Download User Manual

COMPACT
User manual
www.mobi-click.com
More security in all situations!
Product description: What is Mobi-Click "Compact"?
Important information
At first: change the PIN-code!
Switch on Mobi-Click Compact
Mobile phone, emergency and alarm system at the same time!
How do I save the 3 phone numbers?
My first phone call with Mobi-Click Compact
Switch on the alarm standby with another mobile phone
What should I do in case of an alarm?
How will I be informed per SMS in case of an alarm?
Product description: What is Mobi-Click "Compact"?
3
4
6
8
10
12
14
16
18
20
The easiest
mobile phone...
for seniors:
Mobi-Click Compact is suitable as an emergency system for elder and handicapped persons.
With these three numbers you can call for example your doctor, your daughter or the
emergency call service directly.
Mobi-Click for the car
22-23
Mobi-Click at home
24-25
Mobi-Click in the child’s room
How do I choose the right alarm instruction?
Can I change the sensitivity of the sensors?
Whether everything is set correctly? Test!
What is the meaning of the SMS messages?
Eavesdrop in? Yes, but pay attention...!
PIN-Code – How to protect against outside access?
Can I write personal alarm messages?
How can I test if the text is correct?
Individual SMS-instructions
Security zone and localization of persons or objects
How can I connect extern devices?
Declaration of Conformity
Technical data
2
28
29
30
31
32
33
34
36
37
38
39
40
41
Mobi-Click Compact works nearly like a usual mobile phone, just much more easier!
You can receive any calls and dial three pre-programmed phone numbers directly.
26-27
for children (and anxious parents):
With the three coloured buttons, Mobi-Click is also the perfect mobile phone for children
because parents can always contact their children.
and alarm system:
As an alarm system Mobi-Click protects you in different situations:
Car theft and burglary:
With Mobi-Click Compact you can protect your vehicle against theft or your flat, your house
or your office against burglary.
Baby phone:
As a Baby phone Mobi-Click alarms you immediately if your child is crying or climbing out of
bed.
In case of an alarm you are going to receive up to three SMS or phone calls on your three
pre-programmed numbers. You have the possibility to contact undetected Mobi-Click from
any phone and so listen in the room quietly.
Car
Car theft
theft
Burglary
Burglary
Baby
Baby phone
phone
You can protect your Mobi-Click with a PIN-code, so that only you or any allowed person
can communicate with Mobi-Click quietly.
3
Important information
Important information
1. First steps before using the Mobi-Click Compact
Mobi-Click Compact possesses an integrated circuit for the protection of the battery from over and under
charging as well as from short-circuit. This protective circuit is activated with a small slide switch (see design).
In order to avoid damage during transport, this slide switch is set to the OFF position at the factory. Before
first use the protective circuit must be activated by moving the slide switch from the OFF to the ON position.
.
1.
Leave the Compact connected to the battery charger for a minimum of 40 Minutes to ensure that the battery is fully
charged.
2.
2.
Before switching on the Compact (with the ON/OFF key) the battery charger must be disconnected. Once Compact
is switched on, the battery charger can be connected or disconnected as required, or be permanently connected.
This way, a temporally unlimited working time of Compact can be guaranteed (e.g. monitoring during a vacation).
3.
3.
Compact allows the user a variety of programming options and adjustments of the device functions to suit individual
requirements of the user. If during the programming something does not really work, you can reprogram the device,
reset the Compact by moving the reset switch (located under the rear cover) to the OFF position for a minimum of 5
seconds and then ON again. This does not erase previous settings, but sets the Compact ready to receive new
instructions. Restart the Compact after resetting.
(View of the Compact from the rear)
..
..
..
..
..
..
..
..
To set the Compact in operation
To set the Compact in operation
Open the rear cover
Open the rear cover
Open the SIM-card caddy
Open the SIM-card caddy
Using a pointed tool, move the slide switch to the ON position
Using a pointed tool, move the slide switch to the ON position
Insert SIM-card
Insert SIM-card
Close the SIM-card caddy
Close the SIM-card caddy
Close the rear cover
Close the rear cover
Connect the battery charger
Connect the battery charger
A peep signals indicates that the Compact has successfully started
A peep signals indicates that the Compact has successfully started
4
5
PIN
At first: change the PIN-code!
As Mobi-Click Compact has only 3 buttons and a ON/OFF power button some settings have to be done on a second "normal"
mobile phone at the first use.
These settings have to be done just once!
u
Changing of the PIN-code
For the use of Mobi-Click Compact you also need a SIM-card which is like the SIM-cards you need for other mobile phones. It
does not matter which SIM-card you choose, a prepaid-card or a SIM-card with subscription with an operator. Put the SIMcard, which you are going to use for Mobi-Click Compact later, in a "normal" mobile phone first.
Put
Put the
the new
new SIM-card
SIM-card into
into the
the
"normal"
"normal" mobile
mobile phone
phone
y
SIMcard
Every SIM-card has a PIN-code. Since Mobi-Click utilises it own PIN system to guard against unauthorised access by SMS.
Therefore the original PIN-code of the SIM card must be changed (see your mobile phone handbook for changing PIN
instructions). For changing PIN you can use any mobile telephone.
SIMcard
Bottom
Compact
Place the SIM card intended for use in the Mobi-Click into any mobile phone. Using the mobile phone’s menu, navigate to the
changing PIN code option (see your mobile phone handbook for changing PIN instruction) and change the PIN-code as
follows:
new PIN-Code: 1513.
In case of any problems read the instructions of your operator or the instructions of your mobile phone manufacturer.
After changing the PIN-code of your SIM-card, remove the SIM-card from your mobile phone and place it into Mobi-Click
Compact. Open the small cover at the bottom of Mobi-Click Compact and place the SIM-card into the SIM caddy. Carefully
replace the cover.
ATTENTION!
Mobi-Click Compact works only when you delete all messages you have in the "inbox" of your SIM-card.
6
Place
Place SIM-card
SIM-card with
with the
the changed
changed
PIN
PIN into
into Mobi-Click
Mobi-Click Compact
Compact
v
Enter
Enter the
the original
original PIN-code
PIN-code
w
Change
Change the
the PIN-code
PIN-code
(as
(as per
per page
page 6)
6)
x
Take
Take the
the SIM-card
SIM-card out
out
of
of the
the mobile
mobile phone
phone again
again
z
Ready
Ready to
to start!
start!
7
Start
Switch on Mobi-Click Compact
Switch
Switch on
on
Press
Press the
the ON/OFF-button
ON/OFF-button for
for
about
about 55 seconds
seconds
u
v
w
x
AA dual
dual tone
tone indicates
indicates that
that
telephone
telephone mode
mode has
has started
started
The
The yellow
yellow LED
LED comes
comes on
on
Automatic
Automatic GSM
GSM network
network
search
search (ca.
(ca. 20
20 sec.)
sec.)
Press until you hear "peep".
(During this time the red LED
flashes)
Mobi-Click
Mobi-Click
Compact
Compact
works
worksonly
only
if...
if...
}}…it
…itisisswitched
switchedon
onand
and
the
theaccumulator
accumulator
isisloaded.
loaded.
}}…the
…thePIN-code
PIN-codeofofthe
the
SIM-card
SIM-cardhas
hasbeen
been
changed.
changed.
}}…the
…theSIM-card
SIM-cardisisput
putinin
correctly.
correctly.
y
Ready
Ready for
for use
use
8
The
The green
green LED
LED begins
begins
to
to flash
flash and
and the
the yellow
yellow
LED
turns
LED turns off
off
}}…a
…aperfect
perfectGSM
GSM
reception
receptionisisgiven.
given.
ATTENTION!
Should the green LED not start flashing, turn off the Mobi-Click using the ON/OFF-button and
check to ensure the SIM-card has been inserted correctly. Also ensure that you are in a good
mobile phone reception area.
You need
}
}
}
1 Mobi-Click Compact
1 SIM-card
1 mobile phone for changing the PIN-code of the SIM-card and
to program the three phone numbers
Connect Mobi-Click
}
}
}
Ensure the Mobi-Click is turned OFF and connect the battery charger
to ensure that the battery is fully charged.You will hear a short peep
tone when the charging cycle begins
Orange LED is blinking: the battery is not charged
Switch on your device as described on the left page. You should
NOT turn on the Mobi-Click with the charger connected. An
integrated protection circuit is built into the Mobi-Click to ensure
that the battery delivers optimal supply to the Mobi-Click.
Security advise
Mobi-Click Compact was produced by keeping to the strict
manufacturing and quality controls. Thus your device works correctly
and to prevent that the guarantee expires there has to be considered
the following security councils:
}
}
}
}
Take care of your Mobi-Click Compact.
Mobi-Click is full of electronics and sensitive sensors. Therefore
do not drop Mobi-Click, do not expose Mobi-Click any hard hit as
the electronic printed circuit board could get any defect because
of this.
Moisture, heat or cold could influence the perfect work of the
device strongly and lead to damages.
Do not try to open the Mobi-Click device. Thus you damage the
housing and you loose the guarantee service.
What to do if...
…there is no dual tone and the green LED does not light?
}
Is the device switched on?
}
Does the battery have enough power?
}
Is the PIN-code changed, and is the SIM-card inserted correctly?
}
Attention! General Reset (s. pages 4 and 37)
9
Multifunctions
Mobile phone, emergency and alarm system at the same time!
Activate
Activate as
as mobile
mobile phone
phone
Activate
Activate as
as emergency
emergency system
system
Press when switching
on (power ON/OFF).
+
GREY
Set
Set up
up connection
connection
RED
If
If it
it is
is ringing
ringing
ON/OFF
Keep the two
buttons pressed
when switching on
until you hear a
signal tone!
During
During phone
phone call
call
Activate
Activate as
as alarm
alarm system
system
+
BLUE
ON/OFF
Press the two
buttons when
switching on until
you hear a signal
tone!
Switch
Switch on
on alarm
alarm standby
standby
(RED)
Dial
Dial the
the 1st
1st number
number
Reject
Reject call
call
Switch
Switch to
to mute
mute
AUTO
AUTO
(GREEN)
Dial
Dial the
the 2nd
2nd number
number
Answer
Answer the
the call
call
loudly
loudly
Hear
Hear loudly
loudly
(free
(free speaker)
speaker)
HOME
HOME Protection
Protection against
against burglary
burglary
(BLUE)
Dial
Dial the
the 3rd
3rd number
number
Answer
Answer the
the call
call
normally
normally
Hang
Hang up
up
BABY
BABY
Emergency mode:
The call will be answered
automatically after 1 ring.
10
Emergency mode:
Hear the call automatically
loudly (free speaker).
Car
Car monitoring
monitoring
Baby
Baby phone
phone
Press the button until the countdown starts
(peep...peep...). You now have 15 seconds
to leave of the room.
To switch off: press the button again.
Activate
Activate test
test mode
mode
+
GREEN
ON/OFF
Press the two
buttons when
switching on until
you hear a signal
tone!
In
In the
the test
test mode
mode
Switch on: press the same buttons as
described on the left. With the test mode you
can test the different sensors. In case of an
alarm you hear a siren. Switch off: Press the
chosen number again.
In
In an
an emergency
emergency case:
case:
In case of an alarm the three SMS or phone
numbers will be informed. See page 20 and
21.
11
Start
How do I save the 3 phone numbers?
Entering on a normal mobile phone
As easy as SMS...
With Mobi-Click Compact you can dial three different
numbers, without the tiring typing of the phone numbers:
just press one of the three coloured buttons and you are
connected directly to the number you have chosen!
Before you can profit from this short dialling, you have to
save those three numbers first. (You can change them easily
at any time). Therefore you need a normal mobile phone.
At first you have to choose a number for every coloured
button.
Start Mobi-Click Compact in the alarm mode!
Press and hold the blue button at the same time as pressing
the ON/FF button (see page 11)
For every single number you have to create an SMS on a
normal mobile phone and send it to Mobi-Click Compact. You
can also send and save all three number simultaneously using
the set key command (see page 13).
After the numbers have been saved, switch off the
Mobi-Click and restart Mobi-Click in mobile phone
mode.
ATTENTION!
Even if you have one or more of these three numbers set as
SMS in alarm mode – in telephone mode always this number
will be called independently of the alarm set-up.
12
v
Activate Mobi-Click Compact in the alarm mode (see page 11)
u
+
Write
Write aa SMS
SMS instruction:
instruction:
e.g.:
+
Write
WriteaaSMS
SMS
(message)
(message)on
onaa
normal
normalmobile
mobilephone
phone
and
andsend
sendititto
to
Mobi-Click!
Mobi-Click!
Activate
Activate as
as alarm
alarm
system
system (page
(page 11)
11)
Set
Set TEL1
TEL1 +41791234567
+41791234567 red
red button:
button: 1.
1. receiver
receiver
x
w
Send
Send SMS
SMS instruction
instruction
to
to Mobi-Click
Mobi-Click Compact
Compact
The
The number
number isis saved:
saved:
button
button 11 (red)
(red)
{
You
You receive
receive confirmation
confirmation
(SMS)
(SMS)
31.03.2004
10:11
31.03.2004
10:11
COMPACT
COMPACT 42
42
Tel1
== call
Tel1
call
004191123456
004191123456
y
Confirmation
Confirmation of
of
the
the SMS
SMS instruction
instruction
z
triple
triple tone
tone
|
Next
Next number:
number:
continue
continue with
with u
u
e.g:
Set
Set TEL2
TEL2 004179111...
004179111...
e.g.:
Set
Set TEL3
TEL3 +4152765...
+4152765...
TEL1
TEL1 ...
...
red
red button
button
TEL2
TEL2 ...
...
green
green button
button
TEL3
TEL3 ...
...
blue
blue button
button
message
(SMS)
}} Please
Pleaseconsider
considerthe
thespace
spacebars
barsbetween
betweensingle
singlewords
words//numbers:
numbers:Set(space
Set(space
bar)TEL2(space
bar)TEL2(spacebar)+41...
bar)+41...
}} Always
Alwaysinclude
includeintl.
intl.prefixes
prefixesfor
forintl.
intl.phone
phonenumbers
numbers(e.g.
(e.g.0041
0041or
or+41
+41for
for
Switzerland).
Switzerland).
}} Use
Usecapital
capitalor
orsmall
smallletters
lettersor
orboth.
both.
}} Every
new
SMS-order
deletes
the
old
one!
Every new SMS-order deletes the old one!
}} You
Youcan
canstore
storeall
allthree
threenumbers
numbersat
atone
onetime
timeby
bysending
sendingthe
theinstruction
instructionset
setkey
key
followed
followedby
bythe
thethree
threenumbers
numbersyou
youwish
wishto
tosend
sendto
tothe
theMobi-Click
Mobi-ClickCompact.
Compact.This
Thisacts
acts
the
thesame
sameas
asthe
theinstruction
instructionfor
foronly
onlyone
onenumber
number(e.g.
(e.g.set
setTEL/SMS1).
TEL/SMS1).(Note!
(Note!The
The
spaces
spacesbetween
betweenthe
thethree
threenumbers
numbersmust
mustbe
beinserted!)
inserted!)
13
Start
My first phone call with Mobi-Click Compact
Keypad
Keypad lock
lock
Activate
Activate as
as mobile
mobile phone
phone
(see
(see also
also page
page 10)
10)
KEYPAD LOCK:
Switch on Mobi-Click: Press ON/OFFbutton, until you hear the dual tone. Wait
until the network is present (green LED is
blinking). Press again the ON/OFF-button
and press immediately button 1.
If you hear a triple tone, all buttons,
except the ON/OFF, are locked.
Dial
Dial the
the number
number
Keep
Keep one
one of
of the
the three
three coloured
coloured buttons
buttons
pressed
pressed at
at minimum
minimum for
for 33 seconds!
seconds!
RED
GREEN
1
BLUE
2
or
3
or
The
The chosen
chosen connection
connection will
will be
be made
made
During
During the
the
connection
connection
(RED)
Switch
Switch to
to mute
mute
(GREEN) Loudspeaker
Loudspeaker (free
(free speaker)
speaker)
(BLUE)
14
Hang
Hang up
up
IfIf it‘s
it‘s ringing...
ringing...
(RED)
Reject
Reject call
call
(GREEN) Answer
Answer the
the call
call loudly
loudly
(BLUE) Answer
Answer the
the call
call normally
normally
KEYPAD UNLOCK:
Press the ON/OFF-button, until you hear
a clicking signal, then press immediately
button 3. If you hear a triple tone again
now, the keypad is unlocked.
Acoustic
Acoustic
confirmation
confirmation (peep)
(peep)
During the phone
connection:
In
Inthe
thenormal
normalspeech
speechmode
modethe
thegreen
greenLED
LEDflashes.
flashes.In
In
the
thefree
freespeech
speechmode
modethe
thegreen
greenand
andthe
thered
redLED
LEDflash
flash
alternately.
alternately.The
Theorange
orangelight
lightisiscontinuously
continuouslylitlitduring
during
the
thecall.
call.After
Afterhanging
hangingup,
up,aapeep
peepwill
willbe
beheard,
heard,which
which
can
canbe
beunderstood
understoodas
asconfirmation
confirmationfor
forterminated
terminatedcall.
call.
Answer a call automatically – more security for people who live alone or
handicapped persons:
+
+
Activate
Activate as
as
emergency
emergency system
system
(see
page
(see page 10)
10)
Answer
Answeraacall
callautomatically:
automatically:
Elderly
Elderlyand
andhandicapped
handicappedperson
person
are
often
living
alone.
are often living alone.Especially
Especially
this
thisgroup
groupof
ofpeople
peopleisisoften
often
exposed
exposedto
todangerous
dangerous
situations:
situations:aafall
fallor
oran
an
unexpected
collapse
unexpected collapsecould
couldhave
have
bad
consequences.
bad consequences.
When
Whenthe
thecall
callisisanswered
answered
automatically
automaticallyyou
youcan
cancontact
contact
your
yourbeloved
belovedperson
persondirectly
directly
whenever
you
want:
Mobi-Click
whenever you want: Mobi-Click
Compact
Compactanswers
answersautomatically
automatically
and
andput
putthe
thehearhear-and
andspeaking
speaking
settings
settingsto
to"loud"
"loud"(free
(free
speaker),
speaker),thus
thusthe
theperson
persondo
do
not
nothave
haveto
topick
pickup
upthe
the
telephone.
telephone.
Mobi-Click Compact answers automatically after 1 ring.
15
Switch on alarm standby
Switch on the alarm standby with another mobile phone
Activate Compact as alarm system
As easy as a SMS…
Mobi-Click Compact can be set per SMS
instructions with every normal mobile phone.
Therefore you should be able to write and send
SMS messages on your mobile phone, then you
are also able to serve Mobi-Click. All settings of
Mobi-Click are made by a simple principle:
} Write a SMS on your mobile phone.
} Send this SMS to the Mobi-Click Compact
u
+
+
Set
Reset
Test
=
=
=
switch on
switch off
test
2. word: determine situation or sensors
Auto
Home
Baby
=
=
=
vehicle monitoring
room monitoring
baby phone
e.g.:
e.g.:
Set
Set home
home
Set
Set auto
auto
w
Send
Send the
the SMS
SMS instruction
instruction
to
to Mobi-Click
Mobi-Click Compact
Compact
You
You receive
receive short
short
message
message (SMS)
(SMS)
on
on your
your mobile
mobile phone
phone
x
set auto:
Protection against vehicle theft
Vibration-sensor and locating activated.
set home:
Protection against burglary
Motion-sensor activated.
set baby:
Baby phone
Motion- and acoustic- sensor/
microphone activated.
examples:
Test Auto
Set
Set baby
baby
Alarm
Alarm standby
standby isis
activated
activated
Alarm
Alarm isis ready!
ready!
16
Write
Write the
the SMS
SMS instruction
instruction
e.g.:
Confirmation
Confirmation of
of the
the SMS
SMS
instruction
instruction
What is the meaning of the SMS?
v
Activate
Activate as
as alarm
alarm
system
system (page
(page 11)
11)
SMS instructions consist of 2 words:
1. word: what do I want to do?
On your own mobile phone
31.03.2003
31.03.2003 10:11
10:11
COMPACT
COMPACT 42
42
Command:
Command:
SET
SET AUTO
AUTO
Message:
Message:
Command
Command OK
OK
>> End
End of
of Report
Report
test monitoring vehicles
(no alarm calls, on the Mobi-Click an
alarm tone is heard)
Reset Home monitoring rooms switched off
Set Baby
Baby phone switched on
}} Always
Alwaysspace
spacebar
barbetween
betweenthe
the
words.
words.
}} Use
Usecapital
capital//small
smallletters
lettersor
orboth.
both.
}} Every
Everynew
newinstruction
instructiondeletes
deletesthe
the
old
oldone!
one!
}} With
Withthe
theinstruction
instructionset
setalarm
alarm
you
youcan
canactivate
activatethe
theMobi-Click
Mobi-Clickinin
alarm
alarmmode.
mode.
17
In case of alarm
What should I do in case of an alarm?
Activate Compact as alarm system
On your own mobile phone
Keep cool!
}
}
}
}
u
Which persons were be alarmed?
Control: send instruction "Test SMS" to
Mobi-Click.
If you were alarmed per SMS:
Send the instruction "Hear" to Mobi-Click.
Mobi-Click calls you back quietly immediately.
If you were called:
Do not hang up! Now you can listen in the
monitored room/place quietly. After about 2
minutes the connection will be disconnected
by Mobi-Click, but before it will be hanged
up, you will hear peep tone twice (so you
know you were connected to Mobi-Click).
If the alarm standby is not switched off then
there will be sent a new alarm message after
5 minutes if necessary.
SMS
SMS
alarm
alarm message
message
You
You receive
receive aa short
short
message
message (SMS)
(SMS)
on
on your
your mobile
mobile phone:
phone:
v
31.03-2004
31.03-2004 10:11
10:11
COMPACT
COMPACT 42
42
Message:
Message: An
An alarm
alarm
was
was released!
released!
AREA
AREA :: off
off
VIBRA
mid
VIBRA :: off
off
mid
MOVE
:
ALARM
MOVE : ALARM mid
mid
VOICE
VOICE :: ALARM
ALARM mid
mid
Write
Write SMS
SMS instruction
instruction and
and send
send to
to Mobi-Click
Mobi-Click Compact:
Compact:
y
w
Mobi-Click
Mobi-Click calls
calls you
you back
back
automatically
automatically
Alarm
Alarm standby
standby isis
switched
switched off
off
18
(example of an alarm SMS)
Alarm
Alarm isis caused
caused
A Mobi-Click alarm message has always to be
taken serious! Keep cool in any case and consider
your next steps exactly:
Hear
Hear
x
or
IfIf you
you pick
pick up
up you
you can
can
listen
listen quietly
quietly in
in the
the room
room
Reset
Reset ...
...
Home
Baby
Auto
All
...
Always
Always your
your mobile
mobile
phone...
phone...
Please
Please ensure
ensure that
that you
you have
have
saved
saved ALL
ALL the
the numbers
numbers that
that
you
you wish
wish Mobi-Click
Mobi-Click to
to alarm
alarm in
in event
event of
of an
an
alarm
alarm (see
(see page
page 12-13)
12-13)
Do you want to be called if
there is an alarm?
By switching on the alarm
standby add the word "Call" to
the instruction.
Example:
Set baby (normal)
Confirmation and alarm message
per SMS.
Set baby call
Confirmation of Set Baby will be
received by a call on your mobile
phone. In the event of an alarm
there will be a call or SMS to your
mobile phone depending on your
saved settings.
19
Alarm messages
How will I be informed per SMS in case of an alarm?
On your own mobile phone
Triple security!
In case of an alarm Mobi-Click Compact can call
3 alarm numbers altogether and therefore send
up to three different persons a SMS or make a
phone call to them. (see also information by email, page 37).
Examples:
You want to monitor a holiday house. In case of
an alarm Mobi-Click should
} send 1 SMS to your mobile phone
} send 1 SMS to the mobile phone of your wife
} make 1 call to a fix net number
The setting looks like:
} Set SMS1 +41791234567
(Your personal mobile phone number)
} Set SMS2 0041791112233
(Mobile phone number of your wife)
} Set TEL3 +41527654321
(Number of your fix net telephone)
20
If the alarm message
should be sent per SMS:
u
Write
Write an
an SMS
SMS instruction:
instruction:
If the alarm message
should be made per call:
u
Write
Write SMS
SMS instruction:
instruction:
For
For professionals:
professionals:
Alarm number…
(Send all instructions from your mobile
phone to Mobi-Click Compact):
e.g.:
st
Set
Set SMS1
SMS1 +4179123…
+4179123… Number
Number of
of the
the 11st receiver
receiver
(will be informed per SMS)
v
w
e.g.:
st
Set
Set TEL1
TEL1 +4179123...
+4179123... Number
Number of
of the
the 11st receiver
receiver
(will be informed per telephone call)
x
e.g.:
nd
Set
Set SMS2
SMS2 00417911…
00417911… Number
Number of
of the
the 22nd receiver
receiver
e.g.:
rd
Set
Set SMS3
SMS3 +4152765…
+4152765… Number
Number of
of the
the 33rd receiver
receiver
You receive a short message with a list
of all alarm numbers.
change:
change:
Send
Send SMS
SMS to
to Mobi-Click
Mobi-Click
Compact
Compact
Next
Next number:
number:
(repeat
(repeat process)
process)
control:
control:
Test SMS
SMS
SMS only
only in
in alarm
alarm mode!
mode!
You
You can
can save
save 33 numbers
numbers altogether
altogether with
with
Mobi-Click
Mobi-Click Compact.
Compact.
IfIf you
you use
use Mobi-Click
Mobi-Click Compact
Compact as
as aa mobile
mobile phone
phone you
you can
can
dial
dial these
these three
three numbers
numbers directly
directly with
with the
the three
three coloured
coloured
buttons.
buttons.
The
The same
same numbers
numbers are
are used
used to
to make
make an
an alarm
alarm call
call or
or to
to
send
send aa SMS
SMS (message)
(message) like
like described
described here,
here, ifif alarm
alarm standby
standby
isis activated.
activated.
e.g. Set SMS2 004179555…
Old number 2 will be overwritten.
switch
switch off:
off:
e.g. Reset SMS2 (leave empty)
Number 2 will be deactivated.
restart:
restart:
e.g. Set SMS2 (leave empty)
The old number 2 will be reactivated.
switch
switch off
off all:
all:
Reset SMS (leave empty)
All numbers (SMS/TEL) switched off
except number 1.
21
Set Auto
Mobi-Click for the car
Activate
Activate the
the alarm
alarm system
system
Vehicle theft
With Mobi-Click Compact you protect your vehicle (car, machine, motorbike, etc.)
reliably and without any problems against thieves and burglars.
The Vibration-sensor reacts on smallest vibrations (shut the car door, drag s.o.
off, etc.) and causes an alarm message immediately per SMS or phone call to up to
3 pre-programmed numbers.
In case of a vehicle theft there will appear constantly the appropriate location
message (GSM zone code) on your own mobile phone display where the vehicle is
located at the moment. Mobile phone operators and the police are able to locate
your vehicle because of this information.
+
BLUE
Press red button for about 3 seconds. Countdown
starts (peep... peep...). You have 15 seconds to
leave your car. To turn off: press red button
within 15 seconds.
RED
Start
}
22
ON/OFF
Press the two
buttons when
switching on until
you hear a signal
tone!
Activate
Activate alarm
alarm standby
standby (auto)
(auto)
Right placement
}
To install Mobi-Click is not as expensive as to install an alarm device in a car repair
shop: just hide it in your vehicle (e.g. in the glove compartment, in the trunk or also
under the seat).
}
Activate the alarm system as described above. Mobi-Click Compact is now ready. To activate car monitoring function press
the red button. Now the countdown starts automatically (peep…peep…). Quickly hide Mobi-Click Compact in your car and
leave. After 15 seconds Mobi-Click is ready.
The alarm function can also be activated from another mobile phone: just send the following SMS-command to Mobi-Click
Compact "set auto".
Switch off Mobi-Click Compact:
- When you enter your vehicle you can switch off your Mobi-Click Compact by pressing the red button.
Remember: you only have 15 seconds time, before the alarm starts!
(When the alarm is turned off, you hear a triple tone.)
- Or:
send the following SMS-instruction from you mobile phone to Mobi-Click Compact: "reset auto".
The monitoring will be switched off.
23
Set Home
Mobi-Click at home
Activate
Activate the
the alarm
alarm system
system
Burglary
With Mobi-Click Compact you can monitor your flat, your house or office reliably: The
Motion-sensor registers persons which move within a distance of 5 meters. If a
stranger enters the room, an alarm will be caused immediately quietly.
You chose who will be informed per SMS or call if there is a break-in. Now you can
listen undetected in the room and make the necessary steps.
Ranges of application: flat, house, holiday house/flat, boat, camper, office, repair
shop, atelier, shop, restaurant, garage, petrol station, etc.
+
BLUE
ON/OFF
Press the two
buttons when
switching on until
you hear a signal
tone!
Activate
Activate alarm
alarm standby
standby (home)
(home)
Press green button for about 3 seconds.
Countdown starts (peep... peep...). You have 15
seconds to leave the room. To turn off: press
green button within 15 seconds.
GREEN
Start
Right placement
The Mobi-Click has a monitoring radius of approx. 5 meters with a angle of approx.
80°. To ensure best coverage for monitoring, place the Mobi-Click Compact in a
corner.
Do not face the Mobi-Click at a window as movement outside the window can cause a
false alarm. Best placement in the corner of a room (away from window) facing to
the door.
ATTENTION!
In order to ensure the most effective monitoring possible over the greatest area,
position the Mobi Click Compact in a place that allows common access to all rooms.
(e.g. Hallway, stairway etc.)
24
}
}
}
Activate the alarm system as described above. Mobi-Click Compact is now ready. To activate the alarm function in homemode press the green button. Now the countdown starts automatically (peep…peep…). Quickly hide Mobi-Click Compact
in the room and leave. After 15 seconds Mobi-Click is ready.
The alarm function can also be activated from another mobile phone: just send the following SMS-command to Mobi-Click
Compact "set home".
Switch off Mobi-Click Compact:
- When you enter the room you can switch off your Mobi-Click Compact by pressing the green button.
Remember: You only have 15 seconds time, before the alarm starts!
(When the alarm is turned off, you hear a triple tone.)
- Or:
send the following SMS-instruction from you mobile phone to Mobi-Click Compact: "reset home".
The monitoring will be switched off.
25
Set Baby
Mobi-Click in the child's room
Activate
Activate the
the alarm
alarm system
system
Baby phone
Mobi-Click Compact reacts because of the integrated acoustic-sensor/
microphone not only when your child is crying, but also when it climbs out of bed
silently (motion-sensor). You can listen quietly in the child’s room at every time
just to make sure everything is alright.
Range of application: at home, with relatives and friends, especially on holidays in
hotel rooms, camping, etc.
The best is you test the acoustic-sensor by starting the Mobi-Click in test mode
(see page 11)
+
BLUE
26
Press blue button for about 3 seconds.
Countdown starts (peep... peep...). You have 15
seconds to leave the room. To turn off: press
blue button within 15 seconds.
BLUE
Start
Right time / placement
Parents often leave the child’s room while the child is still awake. For avoiding wrong
alarms, switch on Mobi-Click Compact not until your child is silent or send the
instruction "set baby call" from your mobile phone to Mobi-Click. Mobi-Click will be
switched on and calls you back immediately for confirmation. With the instruction
"hear" you can also listen in your child’s room later (see on p. 32).
Put the Mobi-Click in the direction of the child’s bed or the door of the room. If the
child is climbing out of bed the alarm will be caused immediately.
Important: The acoustic-sensor/microphone is set as it reacts not until the child is
really awake and makes sounds 3 times within 30 seconds. (e.g. coughing only one
time does not cause an alarm). The best is you test it. ("Test baby"). To increase
sensitivity generally: "set baby high".
ON/OFF
Press the two
buttons when
switching on until
you hear a signal
tone!
Activate
Activate alarm
alarm standby
standby (baby)
(baby)
}
}
}
}
Activate the alarm system as described above. Mobi-Click Compact is now ready. To activate the alarm function as
babyphone press the blue button. Now the countdown starts automatically (peep…peep…). Quickly hide Mobi-Click
Compact in the child’s room and leave. After 15 seconds Mobi-Click is ready. (The baby should be sleeping this time!)
The Mobi-Click baby sensor is set to MID as default. This can be adjusted by setting the sensitivity to LOW, MID or HIGH
when you send the Set Baby command.
The baby phone alarm function can also be activated from another mobile phone: just send the following SMS-command
to Mobi-Click Compact "set baby".
Switch off Mobi-Click Compact:
- When you enter your child's room you can switch off your Mobi-Click Compact by pressing the blue button.
Remember: You only have 15 seconds time, before the alarm starts!
(When the alarm is turned off, you hear a triple tone.)
- Or:
send the following SMS-instruction from you mobile phone to Mobi-Click Compact: "reset baby".
The monitoring will be switched off.
27
Low/Mid/High
Set ...
How do I choose the right alarm instruction?
Can I change the sensitivity of the sensors?
Choose the right situation
Set
Set Auto
Auto
Protect your vehicle (car, machine, motorbike etc.) reliably against thieves or
burglars! Vibration-sensor and locating are activated.
Set
Set Home
Home
Protect your home (flat, house, holiday house, bureau, etc.) reliably against
burglary or unauthorized entering! Motion-sensor is activated.
Set
Set Baby
Baby
The ideal Baby phone! Reacts not only when your child cries but also when it climbs
out of bed! Motion-sensor and acoustic-sensor are activated.
Low
Low
All integrated sensors of Mobi-Click are set in the factory optimal for the appropriate monitoring
situation. The sensitivity can be adjusted with a simple instruction and so can be set to be more
or less sensitive.
Mid
Mid
Choose a sensor and complete this sensor with a further instruction which influence the
sensitivity:
High
High
Set sensors directly
Set
Set Vibra
Vibra
Vibration-sensor: Reacts on smallest vibrations and is suitable for monitoring of
vehicles of each kind.
Set
Set Area
Area
Locating: For protecting individuals and localizing children and elder people but
also for transporting values or demonstration-cars etc.
Set
Set Move
Move
Set
Set Voice
Voice
Set
Set All
All
28
Motion-sensor (PIR): Registers every move within a distance of about 5 meters.
Put your Mobi-Click with the sensor in direction of the corridor or the door but never
in direction of the window.
Acoustic-sensor (microphone): The hyper-sensitive microphone reacts on voices
or sounds in the monitored room.
All sensors are activated at the same time.
A combination of the sensors is also possible, e.g. "set vibra move".
In set baby you can adjust the sensitivity as required:
Set
Set
baby
baby
high
high
e.g.:
Instruction
Instruction
Sensor
Sensor
Action:
Action:
Set
Set
Vibra
Vibra
Sensitivity
Sensitivity
mid
mid
Set
Set
Voice
Voice Move
Move
high
high
acoustic
acoustic and
and motion
motion sensor:
sensor: high
high sensitivity
sensitivity
Set
Set
All
All
low
low
all
all sensors:
sensors: low
low sensitivity
sensitivity
vibration
vibration sensor:
sensor: mid
mid sensitivity
sensitivity
29
Test
Whether everything is set correctly? Test!
Test
Test SMS
SMS
List
List of
of saved
saved
SMS
SMS and
and telephone
telephone
numbers.
numbers.
31.03.2004
31.03.2004 10:11
10:11
MOBI-CLICK
COMPACT
42
COMPACT
42
MOBI-CLICK
Tel1
Alarm
Tel1
Alarm 11 == SMS
SMS
+41791234567
0049222333444
+41791234567
0049222333444
Tel2
Alarm
TEL
Tel2
Alarm 22 == call
call
TEL
0041791112233
0049333444555
0041791112233
0049333444555
Tel3
Alarm
3
=
off
Tel3
Alarm 3 = off
+41527654321
+4179447710003
+41527654321
+4179447710003
30
Test
Test Status
Status
System
System and
and mobile
mobile
phone
phone values.
values.
31.03.2004
31.03.2004 10:11
10:11
COMPACT
COMPACT 42
42
Battery
Battery :: 55
Signal
:: 55
Signal
Zone
:: 2C57
Zone
2C57
PIN
:: 1234
PIN
1234
AREA:
:: off
AREA:
off
VIBRA
:: off
VIBRA
off mid
mid
MOVE
:: on
MOVE
on high
high
VOICE
:
on
VOICE
: on low
low
Test
Test Alarm
Alarm
Practice
Practice alarm.
alarm.
Mobi-Click
Mobi-Click informs
informs
all
saved
all saved numbers
numbers
per
SMS
or
per SMS or call.
call.
31.03.2004
31.03.2004 10:11
10:11
HOLIDAY
HOLIDAY HOUSE
HOUSE
Message:
Message: An
An alarm
alarm
was
was released!
released!
AREA
AREA :: off
off
VIBRA
mid
VIBRA :: off
off
mid
MOVE
MOVE :: ALARM
ALARM low
low
VOICE
VOICE :: ALARM
ALARM high
high
What is the meaning of the SMS messages?
Test
Test Tel
Tel
Mobi-Click
Mobi-Click calls
calls all
all
saved
saved alarm
alarm
numbers
with
"Tel
numbers with "Tel
1-3"
1-3" in
in succession.
succession.
To
To save
save costs:
costs: do
do
not
pick
not pick up
up the
the
phone.
phone.
SMS and telephone alarm numbers
31.03.2004
31.03.2004 10:11
10:11
COMPACT
COMPACT 42
42
Tel1
== SMS
Tel1
SMS
+41791234567
+41791234567
Tel2
== call
Tel2
call
0041791112233
0041791112233
Tel3
=
off
Tel3
= off
+41527654321
+41527654321
Date / time
Name and software version
Information per SMS
Telephone number 1
Information per call
Telephone number 2
Informed. Switched off
Telephone number 3
Status message
Date / time
Battery
Signal
Zone
PIN
AREA:
VIBRA
MOVE
VOICE
Battery strength (0...5)
Signal strength (0...5)
Actual location (GSM zone)
4-digit PIN-Code (or "off")
Sensors
Alarm status (on /off)
sensitivity (low/mid/high)
5
5
2C57
1234
off
off mid
on high
on low
31.03.2004
31.03.2004 10:11
10:11
HOLIDAY
HOLIDAY HOUSE
HOUSE
Command:
Command:
SET
SET NAME
NAME
HOLIDAY
HOLIDAY HOUSE
HOUSE
Message:
Message:
Command
Command OK
OK
>> End
End of
of Report
Report
Date / time
changed name
"Echo" of the sent instruction
(control for the sender)
Message: instruction received
& operated correctly
End of the report
Problem message:
31.03.2004 10:11
COMPACT 42
:
:
:
:
:
:
:
:
Confirmation of the instruction:
Name and software version
31.03.2004
31.03.2004 10:11
10:11
HOLYDAY
HOLYDAY HOUSE
HOUSE
Message:
Message:
BATTERY
BATTERYLOW
LOW
AREA
AREA :: off
off
VIBRA
:
off
mid
VIBRA : off
mid
MOVE
MOVE :: ALARM
ALARM low
low
VOICE
VOICE :: ALARM
ALARM low
low
Date / time
changed name
Message:
Battery/Accumulator low
Control for the receiver if all
sensors are still working
regularly and have the right
status despite low battery
voltage
31
Set Code / PIN
Hear
Eavesdrop in? Yes, but pay attention...!
Protection of the private sphere is in the constitution of
many countries. It should not and is not allowed to abuse
Mobi-Click for unauthorized monitoring purposes!
The instruction "Hear" causes a soundless call from Mobi-Click to you after
you have received your SMS. Now you can listen in the room or place
without being detected. This is useful if you, for example, use Mobi-Click as
a baby phone and you want to control if everything is OK.
e.g.
Instruction
Instruction
Add-on
Add-on
Hear
Hear
Action
Action
With this function Mobi-Click can be protected against outside access. The PIN-code consists of the word "PIN" and a code.
The code is always 4-digit and cannot contain any signs, but just digits (e.g. "1234").
IMPORTANT:
If you have saved your own Mobi-Click text responses, then all instructions which you transmit to Mobi-Click must have the
same text and PIN-code at the end, e.g. "set auto pin 1234". Without the code the instruction will not be fulfilled. If you
forgot to attach the PIN-code or attached a false PIN, you get a message with "Access denied!". (To save costs, Mobi-Click
sends you this message only once).
Action
Action
Instruction
Instruction
Designation
Designation
Set
Set
code
code
1234
1234
Reset
Reset
code
code
pin
pin 1234
1234
Description
Description
write
write and
and save
save PIN-code
PIN-code
switch
switch off
off PIN-code
PIN-code temporarily
temporarily
Mobi-Click
Mobi-Click calls
calls your
your mobile
mobile phone
phone back
back
Hear
Hear
Tel2
Tel2
Mobi-Click
Mobi-Click calls
calls back
back the
the pre-programmed
pre-programmed telephone
telephone alarm
alarm number
number 22
Hear
Hear
Tel3
Tel3
Mobi-Click
Mobi-Click calls
calls back
back the
the pre-programmed
pre-programmed telephone
telephone alarm
alarm number
number 33
The instruction "Hear Tel2" or "Hear Tel3" is useful if, for example, your fix net telephone does not have the
possibility of writing a SMS but you want to be called back on the fix net nevertheless.
32
PIN-Code – How to protect against outside access?
ATTENTION!
Lost PIN-Code? What to do?
It is possible to do a general reset to factory default settings when you start the Mobi-Click Compact in alarm mode
(see page 11). This will also reset the PIN-Code.
After switching to alarm mode, you will hear 5 peeps, after which you must press and hold the blue button until you hear a
triple tone. Afterwards all settings, including the PIN-Code will be reset to factory default settings.
33
Set Name / Text
Can I write personal alarm messages?
Individual alarm messages:
Individual alarm texts:
Personal texts are used to describe an alarm which had happen more exactly, especially if the alarm message goes
to a third person or if there are several Mobi-Click devices in order.
Change
Change name
name of
of Mobi-Click:
Mobi-Click:
Set
Set
name
name
Reset
Reset
name
name
Maserati
Maserati
Write
Write // save
save new
new name
name (max.
(max. 10
10 signs)
signs)
Name
Name will
will be
be deleted
deleted (Mobi-Click
(Mobi-Click isis called
called "Mobi-Click")
"Mobi-Click")
Change
Change name
name of
of system
system alarm:
alarm:
Set
Set
alarm
alarm
text
text
Babyphone
Babyphone Nathalie
Nathalie (example,
(example, max.
max. 21
21 signs)
signs)
Reset
Reset
alarm
alarm
text
text
Text returns
returns to
to factory
factory default
default
Text
For every sensor can be assigned a personal text which is allowed to consist of 21 signs.
See the following samples:
Set
Set
voice
voice
text
text
Baby
Baby is
is crying!
crying!
Set
Set
move
move
text
text
Burglar
Burglar in
in the
the house!
house!
Set
Set
vibra
vibra
text
text
Alfa
Alfa Romeo
Romeo stolen!
stolen!
Set
Set
area
area
text
text
Left
Left way
way to
to school!
school!
text
text
(example
(example for
for reset
reset text)
text)
Reset
Reset
e.g. vibra
vibra
Reset
Reset
all
all
text
text
Set voice text Baby is crying!
e.g.:
Set name Maserati
Reset name
Mobi-Click is now called "Maserati"
Mobi-Click is called "Mobi-Click" again.
Set alarm text Baby phone Nathalie
Reset alarm
System alarm is called "Baby phone Nathalie" now.
Alarm message is called "system alarm" again.
Set area text left way to school!
Reset all text
34
Reset
Reset System:
System:
+
BLUE
(example
(example for
for reset
reset all
all text)
text)
When acoustic sensor / microphone is activated there will be
the alarm message: "Baby is crying!"
When e.g.your child leaves the way to school you get a
message "left way to school!"
No individual messages.
ON/OFF
Keep
Keepthe
thetwo
twobuttons
buttonspressed,
pressed,than
thanyou
youhear
hear55times
timesaapeep.
peep.Stop
Stoppressing
pressingthe
theON/OFF-button,
ON/OFF-button,you
youcan
can
hear
hearaatriple
tripletone.
tone.Keep
Keeppressing
pressingthe
theblue
bluebutton,
button,till
tillthe
theyellow
yellowLED
LEDlights.
lights.
35
Set E-mail
Test Text
Individual SMS-instructions
How can I test if the text is correct?
As per page 35 different SMS text can be assigned to different sensors. In order to test please follow
he instructions below:
How can I use the notification by e-mail?
Send one of the following SMS to Mobi-Click to test the associated sensor:
Instruction
Instruction
Text
Action
Action
Action
Action
Instruction
Set
Set
Email
Email aaa
aaa
Reset
Reset
Email
Email
Test
Test
Text
Text
The
The alarm
alarm SMS
SMS text
text reply
reply and
and the
the e-mail
e-mail address
address will
will be
be sent.
sent.
Set
Set
SMS
SMS *bbb
*bbb
Test
Test
Text1
Text1
The
The alarm
alarm SMS
SMS text
text reply
reply will
will be
be sent.
sent.
Test
Test
Text
Text
Test
Text2
Text2
The
The area
area and
and the
the vibra
vibra SMS
SMS text
text reply
reply will
will be
be sent.
sent.
Test
Test
Text3
Text3
The
The move
move and
and the
the voice
voice SMS
SMS text
text reply
reply will
will be
be sent.
sent.
Description
Description
Save
Save e-mail
e-mail address
address
(aaa
(aaa==address,
address,till
till23
23signs)
signs)
Notification
Notification by
by e-mail
e-mail deactivated
deactivated
Notification
Notification by
by e-mail
e-mail activated
activated (*bbb
(*bbb == SC-number,
SC-number,till
till88signs)
signs)
Acknowledgement
Acknowledgement to
to the
the indicated
indicated e-mail
e-mail address
address
You can also receive notification by e-mail. In addition you need an e-mail receiver to be informed in the case of
emergency. This is useful if, for example, your daughter is to be informed, however she is in the office all day so a
message is more suitable by e-mail, since she may not use her mobile phone during the day, or does not have her
own one.
This instruction can be deactivated simply with the instruction "Reset Email". In order to determine whether the e-mail
address of the receiver was stored correctly, you send the instruction "Test Text" to Mobi-Click, and you receive a reply,
in which the stored e-mail address is indicated.
You can change this e-mail address also at any time, by again sending a SMS with the instruction "Set Email aaa" and
"Set SMS *bbb" to Mobi-Click Compact. The old stored e-mail address is automatically overwritten.
Attention: The asterisk before the service centre number (SC number) must be always set!
You can get the service centre number from your provider.
36
37
Set Alarm
Set Zone / Area
How can I connect extern devices?
Security zone and localization of persons or objects
With Mobi-Click you can define protection zones, e.g. your child’s way to school. If the child leaves this area (e.g.
because it enters a stranger's car) you will be warned immediately per SMS and you can monitor the situation if
necessary.
Set
Set
Zone
Zone
Define security zone
Learning mode is activated. Mobi-Click gives a short peep every 20 seconds. When finding a new unknown GSM
zone the dual tone signal is heard. Interrupt learning mode: when Mobi-Click is switched off previously learnt
zones remain saved. Reactivate learning mode: "set zone". Mobi-Click can store a maximum of 48 zones. When
this number is exceeded there will be an error tone (peep) and the LED lights continuously. Zones will remain
saved. Stop learning mode: Switch off Mobi-Click. "Reset zone": Security zones will be deleted.
On the way with the car:
It is possible that not all GSM cells can be detected immediately during the security zones learning process
(especially when driving the children's path to school). Some cells may be working to capacity and therefore
they can not be registered by Mobi-Click. That is why it is advisable for urban areas to cross a security zone
slowly or more than once if possible, this allows for every possible GSM cell to be registered by Mobi-Click.
(Security zones can be tested with "Test Area".)
38
Mobi-Click can be connected to an external contact. This contact generates an alarm report to the programmed target call number
in the programmed communication forms (SMS, call, e-mail).
Function/Software
Function/Software
The
The interface
interface of
of Compact
Compact isis normally
normally served
served for
for the
the data-communication
data-communication to
to and
and from
from external
external system-components.
system-components. The
The logical
logical
standby
standby level
level isis in
in this
this case
case LOW.
LOW. IfIf there
there isis aa connection,
connection, then
then this
this stand-by
stand-by level
level will
will logically
logically be
be pulled
pulled up
up to
to HIGH.
HIGH. Therewith
Therewith
Mobi-Click
Mobi-Click Compact
Compact recognises
recognises with
with the
the next
next set
set function
function (SET
(SET XXX)
XXX) or
or with
with the
the next
next mode
mode shift
shift (SET
(SET ALARM)
ALARM) aa standby
standby power
power
connection
connection and
and itit will
will begin
begin to
to monitoring
monitoring this
this additional
additional sensor
sensor automatically.
automatically. ItIt isis also
also important
important to
to make
make the
the connection
connection before
before
activating
activating the
the Mobi-Click
Mobi-Click device
device via
via SMS
SMS or
or buttons.
buttons.
Monitoring
Monitoring together
together with
with other
other sensors
sensors
When
When one
one of
of the
the sensors
sensors isis switched
switched on,
on, then
then this
this contact
contact will
will be
be monitored
monitored automatically
automatically as
as well
well
(e.g.
(e.g. SET
SET HOME,
HOME, SET
SET VIBRA
VIBRA etc.).
etc.).
Sole
Sole Monitoring
Monitoring
With
With the
the command
command SET
SET ALARM
ALARM Mobi-Click
Mobi-Click will
will not
not only
only put
put into
into the
the ""security-mode
security-mode"".. When
When aa contact
contact isis connected
connected itit will
will be
be
focused
focused automatically.
automatically. Because
Because all
all the
the other
other sensors
sensors will
will not
not be
be activated
activated with
with this
this command,
command, solely
solely this
this contact
contact will
will be
be monitored.
monitored.
Activate locating
Alarm
Alarm display
display
Because
Because the
the contact
contact itself
itself does
does not
not own
own aa sole-alarm-display,
sole-alarm-display, an
an identification
identification isis given
given as
as follows:
follows: ifif the
the alarm
alarm report
report isis given
given by
by
SMS
SMS or
or e-mail,
e-mail, then
then aa release
release of
of the
the contact
contact can
can be
be determined
determined because
because even
even though
though there
there was
was an
an alarm
alarm reported,
reported, the
the sensors
sensors
had
no
sole
release.
had no sole release.
Set
Set
Area
Area
Switch
Switch on
on locating
locating monitoring
monitoring
Set
Set
Auto
Auto
Switch
Switch on
on vehicle
vehicle monitoring
monitoring with
with locating
locating monitoring.
monitoring.
Important: Switch your Mobi-Click Compact only on/off when the contact is not connected yet. Else, it can be possible that the
connected hardware will not be interpreted rightly and/or the switching on/off function will not function in proper form.
39
Declaration of Conformity
Technical data
We, MOBI_CLICK AG; Alte Steinhauserstrasse 19; CH-6330 Cham/ZG
declare under sole responsibility that the product:
Mobile Phone and Security System Mobi-Click Compact (suitable for GSM/E-GSM 900 MHz and
PCN 1800 MHz)
To which this declaration relates, is in conformity with the following essential requirements of the
Directive 1999/5/EC: Article 3.1 a), 3.1 b) and 3.2
The product has been tested against the following standards:
Temperature range:
Weight:
Dimensions:
Operating Voltage:
Recharge time:
Standby-Time:
Module:
Battery:
Talk time:
SIM-Card:
Frequency band:
EN 301 511
Harmonised Standard for Mobile Stations in the GSM900/1800 Bands
EN 301 489-01
Electro Magnetic Compatibility Standard for Radio Equipment and Services
EN 301 489-07
Specific (EMC) Conditions for Mobile Radio Equipment, GSM 900/1800
EN 60950/IEC 950
Safety of Information Technology Equipment
EN 50360
Product Standard to demonstrate the Compliance of Mobile Phones with the Basic Restrictions related
to Human Exposure to Electromagnetic Fields
GSM-Class:
EN 50361
Basic Standard for the measurement of Specific Absorption Rate related to Human Exposure to
Electromagnetic Fields from Mobile Phones
Data Service:
1999/519/EC
Council Recommendation on the Limitation of Exposure of the General Public to
Electromagnetic Fields
The product is marked with the CE marking and Notified Body number according to the
Directive 1999/5/EC: Identification mark: 168
Place of Issue: Cham/ZG
40
Date of Issue: 17. 12. 2003
working range –10°C to +55°C
storage range –25°C to +80°C
78g (including battery)
106 mm x 38 mm x 19 mm (LxWxH)
3,45 Volt to 4,2 Volt (nominal 3,6 Volt)
approx. 40 Min. (for a fully discharged battery)
up to 290 hrs. (telephone mode)
up to 200 hrs. (monitoring mode)
Sagem M0110d
BAK 063448S2 Lithium Ion
up to 120 min.
3 Volt
EGSM900 (880 to 960 MHz)
DCS1800 (1.710 to 1.880 MHz)
Class 4 (2 Watt) as per EGSM900
Class 1 (1 Watt) as per DCS1800
SMS
Mobi-Click is designed to the following standards:
GSM 03.03: “Digital cellular telecommunications system
GSM 03.13: “Digital cellular telecommunications system
GSM 04.02: “Digital cellular telecommunications system
GSM 04.03: “Digital cellular telecommunications system
GSM 04.04: “Digital cellular telecommunications system
GSM 04.05: “Digital cellular telecommunications system
GSM 04.07: “Digital cellular telecommunications system
GSM 04.08: “Digital cellular telecommunications system
(Phase
(Phase
(Phase
(Phase
(Phase
(Phase
(Phase
(Phase
2+); numbering, adressing and indentification“. Version 6.6.0.
2+); Discontinuous Reception (DRX) in the GSM system“. Version 6.0.0.
2+); GSM Public Land Mobile network (PLMN) access reference configuration“. Version 6.0.0.
2+); Mobile Station- Base Station System (MS-BSS) interface Channel structures and access capabilities“. Version 6.0.0.
2+); Layer 1 General requirements“. Version 6.0.0.
2+); Data Link (DL( layer General aspects“. Version 6.0.1.
2+); Mobile radio interface signalling layer 3 General aspects“. Version 6.5.1.
2+); Mobile radio interface layer 3 specification“. Version 6.11.0.
41