Download INSTALLATION INSTRUCTIONS

INSTALLATION
INSTRUCTIONS
PARTS LIST
Attachment Kit
P/N 08V03-TR0-100
Accessory
Application
AUTOMATIC DAY/NIGHT
MIRROR
2012 CIVIC
2 AND 4-DOOR
Publications No.
AII 45605
Issue Date
APR 2011
Automatic Day/Night Mirror Kit
P/N 08V03-TR0-100A
Automatic day/night mirror
Automatic day/night mirror harness
Operating Instructions
Harness cover
TOOLS AND SUPPLIES REQUIRED
Phillips screwdriver
Flat-tip screwdriver
Ratchet
10 mm Socket
6
Wire ties
Isopropyl alcohol
Shop towel
Diagonal cutters
Plastic Trim Tool (T/N SILTRIMTL10)
T20 TORX wrench
Flashlight
Clip
Tape
Illustration of the Automatic Day/Night Mirror
Installed in the vehicle
AUTOMATIC
DAY/NIGHT
MIRROR
Urethane tape
AUTOMATIC
DAY/NIGHT
MIRROR
HARNESS
Fuse label
2A FUSE
Q083116AH
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
AII 45605 (1104)
08V03-TR0-1000-90
1 of 12
Without Moonroof and With Hands Free Link
INSTALLATION
Customer Information: The information in this
installation instruction is intended for use only by skilled
technicians who have the proper tools, equipment, and
training to correctly and safely add equipment to your
vehicle. These procedures should not be attempted by
“do-it-yourselfers.”
1.
•
Remove the map light console (unplug two
vehicle connectors).
2 VEHICLE
CONNECTORS
FRONT
4 RETAINING
TABS
RIGHT MAP
LIGHT LENS
Disconnect the negative cable from the battery.
If the vehicle is equipped with map lights, go to step 2,
otherwise go to step 3.
2.
Remove the left and right lenses from the map light
console (four retaining tabs for each lens). Remove
the two bolts.
MAP LIGHT
CONSOLE
With Moonroof
•
BOLTS
Remove the map light console. Then unplug
three vehicle connectors, and remove the switch
(four retaining tabs).
4 RETAINING
TABS
LEFT MAP
LIGHT LENS
Q082401CK
Without Moonroof and Hands Free Link
3 VEHICLE
CONNECTORS
FRONT
•
4 RETAINING
TABS
RIGHT MAP
LIGHT LENS
Remove the map light console (unplug the
vehicle connector).
VEHICLE
CONNECTOR
MAP LIGHT
CONSOLE
FRONT
4 RETAINING
TABS
RIGHT MAP
LIGHT LENS
MAP LIGHT
CONSOLE
2 BOLTS
4 RETAINING
TABS
LEFT MAP
LIGHT LENS
4 RETAINING
TABS
SWITCH
QA21705AH
LEFT MAP
LIGHT LENS
BOLTS
4 RETAINING
TABS
2 of 12
AII 45605 (1104)
Q0D0422BH
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
3.
Remove the driver’s and passenger’s sunvisor
holders.
6.
Wrap the tip of a flat-tip screwdriver with tape. Locate
the slot in the bracket cover, and insert the flat-tip
screwdriver into the slot. Push the hook with the
screwdriver.
FLAT-TIP
SCREWDRIVER
BRACKET COVER
TAPE
PASSENGER’S
SUNVISOR
HOLDER
(Rotate.)
DRIVER’S
SUNVISOR
HOLDER
(Rotate.)
DRIVER’S
SUNVISOR
Q082404BK
4.
HOOK
FRONT
Make sure the
hook slides
into the
bracket cover.
Remove the cover (two retaining tabs).
COVER
Push the
hook.
REARVIEW MIRROR
(Discard.)
While pushing in on the hook,
rotate the sunvisor backward
about 45°.
2 RETAINING TABS
7.
HOOK
Q090602BK
While pushing in on the hook, rotate the driver’s
sunvisor backward about 45°. Make sure the hook
slides into the bracket cover.
NOTE: If the hook did not stay pushed in, return the
driver’s sunvisor to its original position and repeat
steps 6 and 7.
MIRROR
MOUNT
Q083101AH
5.
While holding down the hook as shown, remove the
rearview mirror from the mirror mount.
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
AII 45605 (1104)
3 of 12
8.
Remove the driver’s sunvisor.
11. Put a shop towel in the opening between the driver’s
A-pillar trim and the dashboard to catch any A-pillar
clips that drop.
DRIVER’S
A-PILLAR TRIM
DRIVER’S
A-PILLAR
FRONT
DRIVER’S
SUNVISOR
SHOP TOWEL
Q090603AK
9.
Pull the driver’s door opening seal away from the
A-pillar.
Click to Stop
Click to Play
Q092001AK
12. Remove the driver’s A-pillar trim from the upper clip
and unplug the vehicle connector, if equipped.
Carefully remove the shop towel and any clips that
fell from the driver’s A-pillar trim.
Pull the clip.
NOTE: The upper clip will stay in the body.
UPPER CLIP
DRIVER’S
A-PILLAR
DRIVER’S
A-PILLAR
TRIM
DOOR
OPENING
SEAL
(Pull away.)
VEHICLE CONNECTOR
(if equipped)
if equipped
2 CLIPS
Q082301AK
DRIVER’S
A-PILLAR
TRIM
10. Pull out the driver’s A-pillar trim to release the clips.
Q082308AK
4 of 12
AII 45605 (1104)
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
13. Remove the remaining upper clip from the driver’s
A-pillar.
15. Pull away the door opening seal from around the
dashboard.
2 RETAINING TABS
Push two tabs.
DRIVER’S A-PILLAR
3 CLIPS
UPPER
CLIP
(Discard.)
DOOR OPENING
SEAL
(Pull away.)
HOOKS
DRIVER’S
DASHBOARD
SIDE COVER
Q083001AH
Q082303AK
16. Remove the driver’s dashboard side cover (three
clips, two retaining tabs, and two hooks).
14. Install the new clip to the driver’s A-pillar trim.
17. Remove the driver’s dashboard lower cover (nine
clips and unplug the vehicle connector, if equipped).
CLIP
(supplied)
VEHICLE CONNECTOR
(if equipped)
DRIVER’S
A-PILLAR TRIM
Q0N0533AH
9 CLIPS
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
AII 45605 (1104)
DRIVER’S
DASHBOARD
LOWER COVER
Q072055AK
5 of 12
Installing the Automatic Day/Night Mirror
Without Another Accessory Harness
18. Install the automatic day/night mirror on the mirror
mount as shown, and tighten the TORX screw.
21. Plug the automatic day/night mirror harness 6-pin
connector into the fuse box 6-pin connector.
T20 TORX WRENCH
Torque: 1.6 - 2.0 N·m (0.16 - 0.20 kgf·m, 1.2 - 1.5 lbf·ft).
DRIVER’S SIDE
FUSE BOX
AUTOMATIC DAY/NIGHT MIRROR
HARNESS 6-PIN CONNECTOR
MIRROR
MOUNT
VIEW FROM FRONT
AUTOMATIC DAY/NIGHT
MIRROR
Q083099CH
FUSE BOX 6-PIN
CONNECTOR
Routing the Automatic Day/Night Mirror Harness
Q083102AH
Click to Stop
Click to Play
19. Using isopropyl alcohol on a shop towel, thoroughly
clean the fuse case where the fuse label will attach.
With Another Accessory Harness
22. Unplug the other accessory harness 6-pin connector
from the fuse box 6-pin connector.
AUTOMATIC DAY/NIGHT MIRROR
HARNESS 6-PIN CONNECTOR
FUSE BOX 6-PIN
CONNECTOR
AUTOMATIC DAY/NIGHT
MIRROR HARNESS
2A FUSE LABEL
FUSE CASE
(Clean with isopropyl alcohol.)
Q091801AH
DUMMY
CONNECTOR
(Discard.)
OTHER
ACCESSORY
HARNESS
6-PIN
CONNECTOR
20. Attach the 2A fuse label to the fuse case on the
automatic day/night mirror harness.
DRIVER’S SIDE
FUSE BOX
Q083103AH
6 of 12
AII 45605 (1104)
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
23. Plug the automatic day/night mirror harness 6-pin
connector into the fuse box 6-pin connector.
For Si models, go to step 28. For other models,
continue to step 27.
24. Remove the dummy connector from the automatic
day/night mirror harness 6-pin connector, and plug
the other accessory harness 6-pin connector into the
automatic day/night mirror harness 6-pin connector.
27. Plug the vehicle 5-pin connector (blue) or, if
equipped, the ambient light harness 5-pin connector
(green) to the automatic day/night mirror harness
5-pin connector. Go to step 30.
25. Route the automatic day/night mirror harness to the
driver’s dashboard lower cover opening as shown.
NOTE: If the vehicle is equipped with an ambient
light switch, do not plug the 5-pin connector (blue) to
the automatic day/night mirror harness 5-pin
connector.
VEHICLE 5-PIN
CONNECTOR (Blue)
OR
AMBIENT LIGHT
HARNESS 5-PIN
CONNECTOR (Green)
AUTOMATIC
DAY/NIGHT
MIRROR
HARNESS
5-PIN
CONNECTOR
WIRE TIE
AUTOMATIC DAY/NIGHT
MIRROR HARNESS
VEHICLE
HARNESS
Q083104AH
26. Secure the automatic day/night mirror harness to the
vehicle harness with one wire tie.
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
AII 45605 (1104)
Q083105AH
7 of 12
28. Unplug the vehicle 5-pin connector (blue) or, if
equipped, the ambient light harness 5-pin connector
(green) from the VSA switch, and plug it into the
automatic day/night mirror harness 5-pin connector.
30. Using one wire tie, secure the automatic day/night
mirror harness to the vehicle harness as shown.
NOTE: If the vehicle is equipped with an ambient
light switch, do not plug the 5-pin connector (blue) to
the automatic day/night mirror harness 5-pin
connector.
Align.
VSA SWITCH
WIRE TIE
VEHICLE 5-PIN
CONNECTOR (Blue)
OR
AMBIENT LIGHT
HARNESS 5-PIN
CONNECTOR
(Green) (if equipped)
VEHICLE
HARNESS
AUTOMATIC DAY/NIGHT
MIRROR HARNESS
Q083106BH
31. Route the automatic day/night mirror harness toward
the outside of the vehicle as shown.
AUTOMATIC
DAY/NIGHT
MIRROR
HARNESS
5-PIN
CONNECTOR
Q083107AH
29. Plug the automatic day/night mirror harness 5-pin
connector (blue) to the VSA switch.
VSA SWITCH
AUTOMATIC DAY/NIGHT
MIRROR HARNESS
Q083108AH
AUTOMATIC
DAY/NIGHT
MIRROR
HARNESS
5-PIN
CONNECTOR
(Blue)
Q091901BH
8 of 12
AII 45605 (1104)
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
32. Route the automatic day/night mirror harness
between the dashboard and the driver’s A-pillar.
34. Route the automatic day/night mirror harness behind
the headliner as shown. Be careful not to crease the
headliner.
DASHBOARD
HEADLINER
AUTOMATIC DAY/NIGHT
MIRROR HARNESS
AUTOMATIC DAY/NIGHT
MIRROR HARNESS
DRIVER’S A-PILLAR
Q083109BH
Q083111CH
33. Align the green tape on the automatic day/night
mirror harness with the vehicle clip, and secure the
automatic day/night mirror harness to the vehicle
harness with one wire tie.
35. Plug the automatic day/night mirror harness 7-pin
connector to the automatic day/night mirror.
WIRE TIE
AUTOMATIC
DAY/NIGHT
MIRROR
HARNESS
GREEN
TAPE
AUTOMATIC
DAY/NIGHT
MIRROR
HARNESS
7-PIN
CONNECTOR
VEHICLE
HARNESS
Align.
AUTOMATIC
DAY/NIGHT
MIRROR
Q083112BH
VEHICLE
CLIP
Q083110CH
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
AII 45605 (1104)
9 of 12
2-Door Models
36. Align the green tape on the automatic day/night
mirror harness at the headliner as shown. Route the
automatic day/night mirror harness through the
groove in the harness cover. Secure the harness
cover to the mirror stay, and put the top of the
harness cover behind the headliner.
AUTOMATIC
DAY/NIGHT
MIRROR
HARNESS
Align.
HEADLINER
4-Door Models
AUTOMATIC
DAY/NIGHT
MIRROR
HARNESS
GREEN
TAPE
HARNESS
COVER
Align.
AUTOMATIC
DAY/NIGHT
MIRROR
HARNESS
GREEN
TAPE
HARNESS
COVER
HEADLINER
AUTOMATIC
DAY/NIGHT
MIRROR STAY
AUTOMATIC
DAY/NIGHT
MIRROR
HARNESS
HARNESS
COVER
AUTOMATIC
DAY/NIGHT
MIRROR STAY
AUTOMATIC DAY/NIGHT MIRROR
HARNESS
COVER
37. Using isopropyl alcohol on a shop towel, thoroughly
clean the area where the urethane tape will attach.
VEHICLE PANEL
AUTOMATIC DAY/NIGHT MIRROR
Q091902BH
AUTOMATIC DAY/NIGHT
MIRROR HARNESS
URETHANE TAPE
Q083113BH
HEADLINER
VEHICLE PANEL
(Clean with
isopropyl alcohol.)
AUTOMATIC DAY/NIGHT
MIRROR HARNESS
URETHANE TAPE
Q083114BH
38. Secure the automatic day/night mirror harness to the
vehicle panel with one urethane tape as shown. Be
careful not to crease the headliner.
10 of 12
AII 45605 (1104)
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
39. Using three wire ties, secure the automatic day/night
mirror harness to the vehicle harness as shown.
42. Check that all wire harnesses are routed properly
and all connectors are plugged in.
43. Check the overlap between the headliner and the
driver’s A-pillar trim. Refer to the Service Manual. If
necessary, adjust the overlap.
WIRE TIES
44. Reinstall all removed parts.
45. Reconnect the negative cable to the battery.
46. Press and hold the radio power button for two
seconds to restore the radio and navi (if equipped)
system functions.
VEHICLE
HARNESS
47. Reset the clock.
48. If the IMA battery level gauge is at zero, start the
engine and hold the rpm between 3,500 and 4,000
(no load) in P or N position until the Charge/Assist
meter indicates the IMA system has stopped
charging the battery.
AUTOMATIC
DAY/NIGHT
MIRROR
HARNESS
49. Do the FUNCTION CHECK to verify the operation of
the automatic day/night mirror.
Q083115BH
51. Put the Operating Instructions in the glove box.
40. Non-Si models only: Plug the automatic day/night
mirror harness 5-pin connector (blue) to the VSA
switch.
AUTOMATIC DAY/NIGHT
MIRROR HARNESS
5-PIN CONNECTOR (Blue)
50. Adjust the zone and calibrate as required.
FUNCTION CHECK
1.
Turn the ignition switch to ON (II), but do not start the
engine.
2.
Turn on the switch. Check that the LED lights.
VSA SWITCH
AUTOMATIC DAY/NIGHT MIRROR
SWITCH
(Turn on.)
DRIVER’S
DASHBOARD
LOWER COVER
Q091903AH
41. Reinstall the driver’s dashboard lower cover.
LED
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
AII 45605 (1104)
AUTOMATIC DAY/NIGHT MIRROR
030406AB
11 of 12
3.
Cover the front sensor in the automatic day/night
mirror with your hand, and use a flashlight on the
rear sensor in the automatic day/night mirror. Make
sure the mirror surface becomes dim.
AUTOMATIC DAY/NIGHT
MIRROR
SURFACE
FRONT SENSOR
(Cover.)
FLASHLIGHT
REAR
SENSOR
030407AB
4.
Make sure the parking brake is applied securely.
Step on the brake pedal, and move the select lever
to the “R” position. Repeat step 3, and make sure the
mirror surface does not become dim.
5.
If the automatic day/night mirror does not function
properly, check the fuse and all connectors.
12 of 12
AII 45605 (1104)
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.