Download HCD-CL1/CL3

HCD-CL1/CL3
CD player section
System
Laser
Frequency response
Tape deck section
Recording system
Frequency response
Compact disc and digital
audio system
Semiconductor laser
(λ=780 nm)
Emission duration:
continuous
2 Hz – 20 kHz (±0.5 dB)
4-track 2-channel stereo
40 – 13,000 Hz (±3 dB),
using Sony TYPE I
cassettes
Tuner section
FM stereo, FM/AM superheterodyne tuner
FM tuner section
Tuning range
87.5 – 108.0 MHz
(50 kHz step)
Antenna
FM lead antenna
Antenna terminals
75 ohms unbalanced
Intermediate frequency
10.7 MHz
AM tuner section
Tuning range
AEP models:
531 – 1,602 kHz
(with the interval set at
9 kHz)
Other models:
531 – 1,602 kHz
(with the interval set at
9 kHz)
530 – 1,710 kHz
(with the interval set at
10 kHz)
Antenna
AM loop antenna
External antenna terminals
Intermediate frequency
450 kHz
General
Power requirements
North American model: 120 V AC, 60 Hz
AEP models:
230 V AC, 50/60 Hz
Australian and New Zealand models:
230 – 240 V AC, 50/
60 Hz
Mexican model:
120 V AC, 60 Hz
Korean model:
220 V AC, 60 Hz
Other models:
120 V, 220 V, 230 –
240 V AC, 50/60 Hz
Adjustable with voltage
selector
Power consumption
U.S.A. model:
HCD-CL1:
100 watts
AEP models:
HCD-CL3:
165 watts
HCD-CL1:
100 watts
HCD-CL3/CL1:
0.5 watts (at the Power
Saving Mode)
Other models:
HCD-CL3:
165 watts
HCD-CL1:
100 watts
Dimensions (w/h/d) incl. projecting parts and controls
Approx. 215 × 285 ×
421 mm
Mass
Amplifier/Tuner/Tape/CD section:
HCD-CL3:
Approx. 8.0 kg
HCD-CL1:
Approx. 7.7 kg
Design and specifications are subject to change
without notice.
2
SAFETY CHECK-OUT
After correcting the original service problem, perform the
following safety checks before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs, screws,
and all other exposed metal parts for AC leakage. Check leakage as
described below.
LEAKAGE
The AC leakage from any exposed metal part to earth ground
and from all exposed metal parts to any exposed metal part having
a return to chassis, must not exceed 0.5 mA (500 microamperes).
Leakage current can be measured by any one of three methods.
1.
A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
2.
A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3.
Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The “limit” indication
is 0.75 V, so analog meters must have an accurate low-voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples of
a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2V AC range are suitable. (See
Fig. A)
To Exposed Metal
Parts on Set
0.15 µF
1.5 kΩ
AC
Voltmeter
(0.75 V)
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.