Download 270191 - Service Manual
Transcript
Index 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Technical Specifications, Opening Instructions Layout Parts Assembly 1 Parts Assembly 2, Block Diagram Power Supply, Virtual Strip, Logo Led and I/O & Phones Schematics Power Supply, Virtual Strip, Logo Led and I/O & Phones Pcb Layouts Controls & I/O Schematics (part 1 of 2) Controls & I/O Schematics (part 2 of 2) Controls & I/O Pcb Layout (part 1 of 2) Controls & I/O Pcb Layout (part 2 of 2) Cpu/Dsp & AD/DA Schematics (part 1 of 2) Cpu/Dsp & AD/DA Schematics (part 2 of 2), Hybrid Mic/Line and Output Schematics Timings, Update Procedure, Memory Reset Procedure, Potentiometers Calibration Procedure Cpu/Dsp & AD/DA Pcb Layout Spare Part List Warnings SERVICE MANUAL Notice Service must be carried out by qualified personnel only.Any tampering carried out by unqualified personnel during the guarantee period will forfeit the right to guarantee. For a correct operation of the instrument, after having switched off, be careful to wait at least 3 seconds before switching on again. To improve the device's specifications, the schematic diagrams may be subject to change without prior notice. All components marked by this symbol have special safety characteristics, when replacing any of these components use only manufacturer's specified parts. The (µ) micro symbol of capacitance value is substituted by U. The (Ω) omega symbol of resistance value is substituted by E. The electrolytic capacitors are 25Vdc rated voltage unless otherwise specified. All resistors are 1/8Ω unless otherwise specified. All switches shown in the "OFF" position. All DC voltages measured to ground with a voltmeter 20KOhm/V. Soldering point. Supply voltage. Logic supply ground. Male connector. Test point. Analog supply ground. Female connector. M/F faston connector. Flag joined with one or more flags Chassis ground. with the same signal name inscribed. Earth ground. ATTENTION Observe precautions when handling electrostatic sensitive devices. Address L CODE: 270191M GENERALMUSIC S.p.A. Sales Division: 47842 S.Giovanni in Marignano (RN) ITALY - Via delle Rose, 12 - tel. 0541/959511 - fax 0541/957404 GENERALMUSIC on the NET: http://www.generalmusic.com 1J FALCON • TECHNICAL SPECIFICATIONS SECTION MONO INPUT CHANNEL MIC/LINE A input LEVELS & DATA sensitivity PAD impedance LINE B input sensitivity impedance A/D converter EQ HIGH MID LOW STEREO INPUT CHANNEL LINE input sensitivity impedance A/D converter EQ HIGH HI-MID LO-MID LOW STEREO DIGITAL INPUT Format Level MASTER SECTION MIX 1 ouputs D/A converter impedance D/A converter output level impedance AUX 1&2 outputs D/A converter output level impedance DIGITAL output format output level HEADPHONES output from +4 to -10dB 10kOhms 18 bit linear, oversampling 64 times ±15dB, from 40Hz to 16kHz, from SHELVING to Q=10 ±15dB, from 40Hz to 16kHz, from SHELVING to Q=10 ±15dB, from 40Hz to 16kHz, from SHELVING to Q=10 ±15dB, from 40Hz to 16kHz, from SHELVING to Q=10 IEC958 Professional (AES/EBU) RS422 output level MIX 2 ouputs from -20 to -60dB 30dB 2kOhms / 10kOhms from +10 to -30dB 10kOhms 20 bit linear, oversampling 64 times ±15dB, from 40Hz to 16kHz, from SHELVING to Q=10 ±15dB, from 250Hz to 16kHz, from Q=0.7 to Q=10 ±15dB, from 40Hz to 16kHz, from SHELVING to Q=10 minimum impedance output level 20 bit linear +4dB 600 Ohms 18 bit linear +4dB 600 Ohms 20 bit linear +4dB 600 Ohms IEC958 Consumer (S/PDIF) 0.5Vpp/75Ohms 32 Ohms 2W Opening Instructions CONNECTORS Disconnect the instrument from the mains. Carefully turn the mixer over and unscrew the screws marked with the arrows. Hold the top and bottom chassis tightly and turn the the mixer right way up, lift off the top chassis as shown below with care without forcing the cables. Balanced XLR-F Balanced JACK Balanced JACK XLR-F Balanced XLR-M Impedance Balanced JACK Impedance Balanced JACK Phono RCA Stereo JACK GENERAL SPECIFICATIONS Sampling frequency 48kHz Dynamic range 117dB adiacent input CH -90dB @ 1kHz Crosstalk input to output -100dB @ 1kHz PAN -85dB @ 1kHz all faders closed -110dB Noise MIX fader nominal -105dB MIX fader nominal + 1 CH -95dB Total harmonic distorsion <0.03%, 20Hz - 20kHz (THD + Noise) <0.02%, 20Hz - 20kHz kg 5.7 Weight mm (WxHxD) 440x110x500 Dimensions J2 DRW G.Boccato DWG# 550638 PCB# GENERALMUSIC S.p.A. ITALY CKD M.Mulazzani DISK: 4 PRT: 1/1 Opening Instructions APP. F.Gazzilli REV: 05/05/99 ALL RIGHTS ARE RESERVED, NO COPIES OR REPRODUCE THIS DOCUMENT WITHOUT WRITTEN CONSENT BY GENERALMUSIC. 3 3 23 3 22 21 2 1 3 24 4 25 26 27 26 28 29 30 31 5 6 7 10 8 11 7 10 7 20 10 33 32 19 8 11 18 8 11 17 7 12 9 13 13 13 13 13 13 14 14 8 11 8 11 15 8 10 8 11 16 3J 25 33 34 35 24 36 43 44 CN31 CN7 37 CN3 CN2 CN4 21 CN1 CN5 CN1 CN2 CN1 CN2 CN4 CN3 39 CN5 CN1 CN3 45 CN9 CN8 CN1 CN14 CN7 CN2 CN7 CN13 CN6 CN6 CN10 CN12 CN5 CN26 CN11 CN5 CN1 CN4 CN4 CN9 CN3 46 CN2 CN1 CN6 CN28 CN3 41 J4 38 40 CN29 CN30 49 DRW G.Boccato DWG# 550636 PCB# GENERALMUSIC S.p.A. ITALY CKD M.Mulazzani DISK: 4 PRT: 1/1 APP. F.Gazzilli REV: 05/05/99 Parts Assembly 1 (for descriptions see REF column on Spare Part List further on this manual.) ALL RIGHTS ARE RESERVED, NO COPIES OR REPRODUCE THIS DOCUMENT WITHOUT WRITTEN CONSENT BY GENERALMUSIC. POWER SWITCH 2 238086 TRANSFORMER 60W 230Vac (EU) 230087 TRANSFORMER 60W 115Vac (US) CN2 CN1 768197 - MAINS FILTER BOARD 23 3 +48V 50 CH1 IN A MIC-XLR BALANCED PAD -30dB 768190 - POWER SUPPLY BOARD CN11,12,13,14 GAIN A/B + - 22 +48V PHANTOM SUPPLY +/-12V ANALOG SUPPLY +3,7V AD/DA SUPPLY +/-5V AD/DA SUPPLY +5V DIGITAL SUPPLY SLIDER MOTOR SUPPLY +/-12V PHONES SUPPLY FAN CH1 IN B LINE-JACK BALANCED +48V CN7 GAIN CN1 PAD -30dB CN3 CN9 20bit MODULATOR ADC RS-232 AES/EBU DSP SECTION CH7/8 A/B 18bit ADC 1/2 CODEC + - 18bit ADC 1/2 CODEC CN1 CN4 +48V GAIN PAD -30dB 4Mbit DRAM A/B MIX1 L + - 20bit PCM DAC SP/DIF AUDIO DIGITAL TRANSMITTER FOOT SWITCH CN7 AD0-AD15 ARM SECTION PERIPHERIAL SECTION CH9/10 IN B LINE-JACK BALANCED 4Mbit DRAM DA0-DA19 RED - ARM/CPU & DSP PAD -30dB AUDIO DIGITAL RECEIVER DD0-DD31 CN4 +48V CH4 CH5 MIDI IN MIDI OUT MIDI THRU CH5/6 GAIN IN A MIC-XLR BALANCED CN8 20bit MODULATOR ADC + - IN B LINE-JACK BALANCED IN A MIC-XLR BALANCED CN10 768201 - CPU/DSP & AD/DA BOARD CLOCK 24.576 MHz CH3/4 A/B CH3 52 CN7 20bit MODULATOR ADC +48V GAIN CH4 CN9 CH1/2 IN B LINE-JACK BALANCED 20 CN2 + CN6 CH3 CN3 A/B CH2 IN A MIC-XLR BALANCED CN5 768191 - I/O & PHONES BOARD 6 PAD -30dB CN4 CN5 CH2 IN A MIC-XLR BALANCED CN6 8Mbit FLASH MEMORY PHONES 4Mbit DRAM CN2 56 CN4 51 18bit DAC 1/2 CODEC PHONES POWER AMPLIFIER PHONES AA0-AA19 OPTION BOARD CH5 PAD -30dB A/B MIX2LR IN B LINE-JACK BALANCED CN27 CN5 + - CN1 CH7 768193 - VIRTUAL STRIP BOARD 18bit DAC 1/2 CODEC SENS. +4dB -10dB LINE-JACK BALANCED INPUT CN2 20bit PCM DAC CH6 CN2 BIR0-BIR7 AUX1/2 + - SENS. +4dB -10dB AD0-AD13 CONTROLS ADC IN INTERFACE CONTROLS INTERFACE CN2 CN8 CN3 CH6 CN1 20bit PCM DAC +48V GAIN IN A MIC-XLR BALANCED RESET MIX1 R CN3 IN B LINE-JACK BALANCED CN1 CH8 + - LINE-JACK BALANCED INPUT SENS. +4dB -10dB CH9 LINE-JACK BALANCED INPUT 54 49 53 PHANTOM POWER + CN3 SENS. +4dB -10dB CH10 55 CN2 CN31 CN30 CN29 +48V CN26 768196 - LCD DISPLAY 128X64dots CN28 768195 LOGO LED BOARD CN5 CN27 + - LINE-JACK BALANCED INPUT CN2 X2 CN1 MIX1LR XLR BALANCED OUTPUT POTs & FADERS MATRIX DEMULTIPLEXERS X2 METERS & INDICATORS LATCH S/P REGISTERS CN6-25 MIX2LR LINE-JACK IMP. BAL. OUTPUT SWITCH SHIFT P/S REGISTERS X2 AUX1-2 LINE-JACK IMP. BAL. OUTPUT 768192 - CONTROLS & I/O BOARD DRW G.Boccato DWG# 550637 PCB# GENERALMUSIC S.p.A. ITALY DRW G.BOCCATO DWG# 550634 CKD M.Mulazzani DISK: 4 PRT: 1/1 DSK# REV: 05/05/99 ALL RIGHTS ARE RESERVED, NO COPIES OR REPRODUCE THIS DOCUMENT WITHOUT WRITTEN CONSENT BY GENERALMUSIC. CKD APP. F.Gazzilli Parts Assembly 2 (for descriptions see REF column on Spare Part List further on this manual.) M.MULAZZANI APP. F.GAZZILLI PART: REV: 05/05/99 GENERALMUSIC S.p.A. ITALY PCB# SCHEMATIC DIAGRAM FALCON BLOCK DIAGRAM ALL RIGHTS ARE RESERVED, NO COPIES OR REPRODUCE THIS DOCUMENT WITHOUT WRITTEN CONSENT BY GENERALMUSIC. 5J J6 MAINS FILTER BOARD (PCB#310642) LOGO LED BOARD (PCB#313049) POWER SUPPLY BOARD (PCB#313039) VIRTUAL STRIP BOARD (PCB#313046) I/O & PHONES BOARD (PCB#313023) DRW: BOCCATO DWG: 313039/046/ 049/023 CKD: MULAZZANI DISK: 4 PART: 1/1 APP: GAZZILLI REV: 05-05-99 SCHEMATIC DIAGRAM FALCON Power Supply, Virtual Strip and I/O & Phones Board Pcb Layouts GENERALMUSIC S.p.A. Italy ALL RIGHTS ARE RESERVED, NO COPIES OR REPRODUCE THIS DOCUMENT WITHOUT WRITTEN CONSENT BY GENERALMUSIC. 7J J8 9J CONTROLS & I/O BOARD (PCB#313045) PART 1 OF 2 J 10 DRW: BOCCATO DWG: 313045 SCHEMATIC DIAGRAM CKD: MULAZZANI DISK: 4 PART: 1/2 Controls & I/O Board Pcb Layout APP: GAZZILLI REV: 05-05-99 FALCON GENERALMUSIC S.p.A. Italy ALL RIGHTS ARE RESERVED, NO COPIES OR REPRODUCE THIS DOCUMENT WITHOUT WRITTEN CONSENT BY GENERALMUSIC. CONTROLS & I/O BOARD (PCB#313045) PART 2 OF 2 DRW: BOCCATO DWG: 313045 SCHEMATIC DIAGRAM CKD: MULAZZANI DISK: 4 PART: 1/1 Controls & I/O Board Pcb Layout APP: GAZZILLI REV: 05-05-99 FALCON GENERALMUSIC S.p.A. Italy ALL RIGHTS ARE RESERVED, NO COPIES OR REPRODUCE THIS DOCUMENT WITHOUT WRITTEN CONSENT BY GENERALMUSIC. 11 J J 12 13 J Operating System Update Procedure POWER & RESET TIMING Tools required POWER OFF POWER ON ✓ 4.63V ✓ ✓ 20mS A 486/33 or superior computer with Windows 95 or 98 or NT installed on it, provided with a RS232 compatible serial port. The RS232 cable (code 130436) supplied with the mixer. The last version of FLASH BLASTER II Disk (code 955914), or the last version of the Operating System that can be downloaded from the Lem internet web site: http://www.lemaudio.com Potentiometers Calibration Procedure When you replace or repair a CPU/DSP & AD/DA Board you must execute the potentiometers calibration procedure to align the sliders and rotating potentiometers with their AD converter, to do this perform the following procedure: ✓ ✓ ✓ Setup ✓ >200mS ✓ AD/DA TIMING 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 1 2 3 4 5 6 7 BCLK 3.072MHz Connect the Computer and the Mixer with the appropriate cable. Install the Flash Update Utility program onto your computer. To do this insert the disk named FLASH BLASTER II in your 3.5" drive, or unpack the Operating System file downloaded, open the drive or the folder and double click on Setup.exe icon, follow the instructions that appears on your computer screen. Procedure ✓ LRCK BB_LR 48KHz ✓ BB_LE ✓ DATA1/2 0 CH7/8 CH9/10 0 b19 0 b0 ✓ 0 b0 b17 ✓ ✓ DIGIOUT 0 b23 b0 0 Turn on the mixer, press and hold the HELP/OPTION button until the display shows "OSCILLATOR", press PAGE UP(+) button to jump to the next screen that says: PRESS ENTER TO UPDATE THE SOFTWARE (note: you can exit from this procedure by pressing any other button, or switching off the mixer at this time) Press ENTER, the display screen disappear and the W led lights to confirm that the mixer is waiting to receive the new operating system from RS232 port. Start the Flash Update Utility program and check the connection between mixer and computer correspond to the port setting on Option/Setting menu. Click on Go! button, the display will show the status of the upgrade and the mixer E/H led lights on, during the uploading the meter leds light sequentially, while the Flash memory is cancelled all the meter leds light and when the memory is reprogrammed all meter leds flash, the total time to perform all operations take aprox. 3min. At the end of re-programming all meter and E/H leds turn off. Switch off the mixer. VERY IMPORTANT: to ensure the correct operation of all mixer functions you must execute a MEMORY RESET procedure before using the Falcon. Troubleshooting ✓ DATA/L1 DATA/R1 0 b19 b0 0 ✓ DATAPHONES DATA/MIX2 DATA/AUX 0 0 b19 Low Level Loading Procedure 0 b0 b17 ✓ 0 b0 ADC TIMING (CH3-6) ✓ SYSCLK 12.288MHz With this procedure you can load the Operating System in the mixer from beginning as if it is never been loaded previously. Turn on the mixer holding down the VIEW and ENV buttons of Channel 1 and VIEW DIGITAL and VOL buttons of Virtual Channel, the led W must light to confirm that the mixer is waiting to receive the operating system from RS232 port (see Operating System Update procedure). If the led W does not light the Low Level programming of the CPU/DSP & AD/DA Board does not operate properly: it must be returned to the manufacturer to be re-programmed. Memory Reset Procedure D0,D2,D3,D4 3/4 or 5/6 ✓ LRCK3/4 LRCK5/6 48KHz J 14 If, for any reason, the system is not updated or the mixer do not operate correctly, you can restart it with the Low Level loading procedure, see below. Any other malfunction is described in the Flash update utlity disk in a folder named Docs. DRW BOCCATO DWG# 550639 PCB# GENERALMUSIC S.p.A. ITALY CKD CARBONI DISK: 4 PRT: 1/1 TIMING TABLE APP. GAZZILLI REV: 05/05/99 ALL RIGHTS ARE RESERVED, NO COPIES OR REPRODUCE THIS DOCUMENT WITHOUT WRITTEN CONSENT BY GENERALMUSIC. When you update the Operating System, or when you replace or repair the CPU/DSP & AD/DA Board you must execute the Memory Reset procedure to clean all memory data. Switch on the mixer holding down the VIEW and ENV buttons of 7/8 and 9/10 channels, the display shows a warning message and execute the RAM memory reset. ✓ ✓ ✓ ✓ ✓ Press GLOBAL and then press PAGE UP twice, the display shows PASSWORD: - +++++++. Press ENTER, the display shows PASSWORD: - M Write FALKNET instead M using the Dial and the ENTER button. Press rapidly ENTER twice: the display shows POT CALIBRATION, press ENTER. Set the controls as follow: HIGH, MID, LOW (and also MID-HIGH, MID-LOW for CH7/8 and CH9/10) and PAN potentiometers of all channells at the centre of their strokes, CH1 up to CH4 faders at MIN, CH5 up to CH9/10 faders at MAX, (the other potentiometers are irrelevant). Press ENTER to view the current reading values of the potentiometers. Press and hold the ENTER button to start the calibration, when the display shows CALIBRATION DONE you may press and hold ENTER to view the new reading values. Press ESC to stop reading, press rapidly ESC twice to escape from calibration and GLOBAL to return at the main screen. CPU/DSP & AD/DA BOARD (PCB#313057) DRW: BOCCATO DWG: 313057 SCHEMATIC DIAGRAM CKD: MULAZZANI DISK: 4 PART: 1/1 Cpu/Dsp & AD/DA Board Pcb Layout APP: GAZZILLI REV: 05-05-99 FALCON GENERALMUSIC S.p.A. Italy ALL RIGHTS ARE RESERVED, NO COPIES OR REPRODUCE THIS DOCUMENT WITHOUT WRITTEN CONSENT BY GENERALMUSIC. 15 J 141102 141101 141100 140917 140085 120857 110119 100920 100066 100059 100058 100045 100043 090918 090916 090863 090194 090183 080606 080605 080342 080168 080156 060561 060512 060048 042615 042558 042537 042475 042435 042425 030880 030858 030520 Spare Part List Legend w EU =Specify European Version (230Vac) US =Specify United States Version (115Vac) 1st =This version has the power switch on logo 2nd =This version has the power switch on rear panel Ref Code Description Optional Accessories 130301 44 2mt Midi Cable Optional I/O kit Accessories 955926 955914 300617 277337 277336 277335 277330 130436 130432 130297 130283 Dump Utility Disk for Windows 95/98/NT Flash Update Utility Disk for Windows 95/98/NT Owner's Manual Folder Quick Guide (Italian-English) Midi Reference Book (all languages) Owner's Manual (English) Owner's Manual (Italian) 25 to 9 pins RS232 Serial Cable 9 to 25 pins RS232 Adaptor Mains Cord (EU) Mains Cord (US) Assembly 21 17 1 19 9 16 54 14 13 15 18 35 41 32 33 36 24 38 25 37 Top Assembly 657264 Logo Rubber Pad 657263 Data Entry Rubber Pad 657262 Top Chassis 657261 Dial Rubber Pad 657260 Channels Rubber Pad 347383 White Knob for Motorized Slider 347382 Antidust for Sliders 347354 Yellow Knob for Slider 347343 White Knob for Slider 347342 Red Knob for Slider 340493 Dial Knob 340186 Adhesive Cable Fixing 340115 Adhesive Flat Cable Fixing 210216 Adhesive Rubber Foam 20x5mm (Specify mt) 210215 Adhesive Rubber Foam 10x1.9mm (Specify mt) 177699 Metal Shield for Flat Cable 177698 Dial Support 120960 Dial Steel Sphere 120042 M2x2mm Screw Bottom Assembly 768195 Logo Led Board (Pcb#313049) 340856 * 6,4mm Led Spacer 140918 * 2 Contacts Hor Male Connector 080712 * Led 3mm 44deg High Eff Green 727600 Fan 5Vdc 40x20mm 667680 Option Slot Cover 667679 Bottom Chassis 347030 Board Spacer h=4.8mm 340916 Switch Button (1st) 340754 Rubber Foot 177694 Power Switch Support (1st) 177694 Logo Support (2nd) 110614 Mains Socket 110367 Fan Grid 40mm 110285 Phantom Power Switch 110320 Power Switch (1st) 110291 Power Switch (2nd) 110012 T1.6A Fuse 5x20mm (EU) 110008 T315mA Fuse 5x20mm (EU) 110003 T3.15A Fuse 5x20mm (EU) 768197 230568 140010 020493 010545 49 53 46 20 4 5 12 11 10 22 51 23 2 Mains Filter Board (Pcb#310642) * 10mH 250Vac 1A AC Line EMI Coil "Siemens" * 3 Contacts P=10 Vert Terminal Block * 100n 250Vac MKP EMI Capacitor "Siemens" * 4n7 250V Ceramic Capacitor (Iec-Ul-Csa) Transformer 39 39 238087 238086 40 J 16 768190 340154 340079 340078 3 Transformer 115Vac 60W (US) Transformer 230Vac 60W (EU) Power Supply Board Power Supply Board (Pcb#313039) * TO3/TO218 Mica Washer * TO220 Mica Washer * TO220 Insulated Bush 6 Contacts Vert Male Connector 4 Contacts Vert Male Connector 2 Contacts Vert Male Connector (CN1-5) 2 Contacts Vert Male Connector Vertical 2 contacts P=10mm Terminal Block Vertical Male Faston 6.3mm Fuse Clip 10A max (EU) (US) LM336Z 2.5V 10mA Voltage Reference LM317 1.2-37V 1.5A Adjustable Regulator 7805 +5V 1A Voltage Regulator 7905 -5V 1A Voltage Regulator 7812 +12V 1A Voltage Regulator 7912 -12V 1A Voltage Regulator MJE15030 TO220 Npn Transistor MJE340 TO126 Npn Transistor TIP36C TO218 Pnp Transistor BC560 TO92 LN Pnp Transistor BC550 TO92 LN Npn Transistor GBU8D 8A Rectifier Diodes Bridge KBL02 4A 200V Rectifier Diode Bridge 30V 1W 5% Zener Diode W02M 1.5A Rectifier Diodes Bridge 1N4002 1A 100V Rectifier Diode 4K7 2W 10% Resistor 1K5 1W 5% Resistor 0E22 3W 5% Resistor 12K1 1/4W 1% Metalized Film Resistor 4K42 1/4W 1% Metalized Film Resistor 3K01 1/4W 1% Metalized Film Resistor 825E 1/4W 1% Metalized Film Resistor 432E 1/4W 1% Metalized Film Resistor 332E 1/4W 1% Metalized Film Resistor 10000uF 25V Snap-In Electrolytic Capacitor 4700uF 25V 20% Vert Electrolytic Capacitor 1000uF 100V 20% Vert Electrolytic Capacitor Controls & I/O Assembly Mains Filter Board 34 * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * 52 727599 768193 340771 141015 141013 140918 140529 100963 100066 080705 072000 060260 768192 768196 140946 080754 347385 347384 347353 347348 347346 347334 347333 347027 340771 230559 141206 141188 141120 141119 141018 141015 141013 141010 140918 140899 140863 140531 140529 140236 120849 120790 110261 102014 102004 100919 100663 100618 Controls & I/O Assembly * Motorized Slider Board (Pcb#313046) ** Led Spacer H=16,3mm ** 14 Contacts Vert Female Connector ** 10 Contacts Vert Female Connector ** 2 Contacts Hor Male Connector ** Microswitch 12V 50mA 0.25mm ** BA6218 SIP Reversible-motor Driver ** LM317 1.2-37V 1.5A Adjustable Regulator ** Led 3mm 60deg Diffused Red ** 10K Lin 60mm Motorized Slider ** 12E 1W 5% Resistor * Controls & I/O Board (Pcb#313045) ** 128x64dots Display Lcd Assembly *** 20 Contacts Bottom-Entry Female Connector *** LMC97S005A Lcd Display 128X64 dots ** Yellow Switch Cap ** White Switch Cap ** Yellow Potentiometer Knob ** White Potentiometer Knob ** Black Potentiometer Knob ** Led Meter Glass ** Led Meter Support ** Led Spacer H=11mm ** Led Spacer H=16,3mm ** 20uH 50V 3A Dc Line Filter ** Vert Male XLR Socket (NC3MAV Neutrik) ** Vert Female XLR Socket (NC3FAV2-0 Neutrik) ** 4 Contacts Hor Male Connector (CN3) ** 2 Contacts Hor Male Connector (CN30) ** 20 Contacts Vert Female Connector ** 14 Contacts Vert Female Connector ** 10 Contacts Vert Female Connector ** 4 Contacts Vert Female Connector ** 2 Contacts Hor Male Connector ** 20 Contacts Strip ** 34 Contacts Hor Female Connector Din41651 ** 2sw 2pos V Slider Switch ** Microswitch 12V 50mA 0.25mm ** Jack V S-F Socket NJ3FDV Neutrik ** Hor Pc Male Faston 2.8 ** Spacer M3-M2 H=8.7mm ** Dial Encoder with Snap ** Hybrid Balanced Mic/Line Input ** Hybrid Master & Balanced Output ** MC33078 Dual LN Operational Amplifier ** 74HC4051 8ch Analog Multiplexer ** 74HC14 Hex Inverter Schmitt Trigger 6 7 8 55 50 43 29 30 28 26 27 31 100613 100608 100602 090183 080733 080731 080716 080706 080705 080242 075589 074696 074695 072600 050493 050492 030931 010713 768191 230569 141187 141120 141119 141015 141010 140861 140251 140217 140212 120849 100911 100734 100602 100035 080103 070231 060255 667686 347030 ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** * ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** * * 74HC4094 8bit Shift/Latch Register 74HC165 8bit P To S Shift Register 74HC04 Hex Inverter BC550 TO92 LN Npn Transistor Led 2.5x5mm Rect Diffused Green Led 2.5x5mm Rect Diffused Red Led 5mm 60deg Diffused Green Led 3mm 60deg Diffused Green Led 3mm 60deg Diffused Red 6V2 1W 5% Zener Diode 10K 9mm Vert Rotary Alog Potentiometer 50K 9mm Vert Rotary Lin Potentiometer w/Click 50K 9mm Vert. Rotary Lin Potentiometer 50K 60mm Slider Lin Potentiometer 10Kx4 1/8w 5% Resistor Array 10Kx8 1/8w 5% Resistor Array 10u 35V 20% Electrolytic Tantalium Capacitor Piezoelectric Buzzer I/O & Phones Board (Pcb#313023) FL5R200PNT EMI Coil For Signal Hor Female XLR Socket (NC3FAH Neutrik) 4 Contacts Hor Male Connector 2 Contacts Hor Male Connector 14 Contacts Vert Female Connector 4 Contacts Vert Female Connector 25 Contacts Hor Male Connector Din41652 Rca Horizontal Female Socket Jack Slim Horizontal S-F Socket 5 Poles Din Horizontal Female Socket Hor Pc Male Faston 2.8 TDA1521Q 12w Dual Power Amp MAX202E RS232 Drivers/Receiver 74HC04 Hex Inverter 6N138 Optocoupler 1N4148 100mA 75V Signal Diode 47K 20% Ver Linear Trimmer +Knob 10E 2W 10% Resistor Internal Chassis Board Spacer h=4.8mm 042353 010722 110300 * * * 90E9 1/4W 1% Metalized Film Resistor 24.576MHz Quartz Resonator 4.8V 280mAh Nicd Battery Wiring Connections 841177 840765 778142 841158 841157 841156 841155 841071 840800 840769 840758 840586 2 Wires 25cm Length C. T. Cable with Faston 2 Wires 20cm Length Crimp Terminal Cable Supply Cables Assembly 14 Wires 40cm Length Flat Cable 14 Wires 25cm Length Flat Cable 10 Wires 15cm Length Flat Cable 4 Wires 55cm Length Flat Cable 20 Wires 30cm Length Flat Cable 14 Wires 3cm Length Flat Cable 4 Wires 40cm Length Flat Cable 4 Wires 45cm Length Flat Cable 34 Wires 30cm Length Flat Cable Cpu/Dsp & AD/DA Board 45 768201 250524 231000 230591 177711 141121 141119 141018 141015 141010 140889 140877 140874 140866 106005 106003 106001 105008 104030 104003 103036 103035 103033 103030 103024 103023 103022 103021 103012 103010 103007 103003 103001 103000 100920 090856 090153 090152 081000 042725 042715 042615 042428 042361 Cpu/Dsp & AD/DA Board (Pcb#313057) * 25x25mm Thermoconductor Adhesive * BLM21A102STP Smd EMI Coil For Signal * 0.1-55MHZ Digital Line Transformer * Heatsink for Cpu * 6 Contacts Hor Male Connector * 2 Contacts Hor Male Connector * 20 Contacts Vert Female Connector * 14 Contacts Vert Female Connector * 4 Contacts Vert Female Connector * Dual In Line Vert Male Strip (specify contacts) * Jumper For Contacts Strip (p=2.54mm) * Single In Line Vert Male Strip (specify contacts) * 34 Contacts Vert Male Connector * MC33202D SOIC Rail-to-rail Op. Ampl. * MAX709 Power Monitor With Reset * MC33078P SOIC Dual Low Noise Op. Amp. * RED208 Risc Cpu and Dsp * AM29F400B-90EC TSOP 4Mbit Flash Memory Ta=90nS * HM514260JP SOJ 4Mbit Dynamic Ram Ta=70ns * CS8402A Audio Digital Interface Transmitter * AD1892JR Audio Digital Interface Receiver * TDA1305T SOT Dual Bitstream DA Converter * 74HC32D SOIC Quad 2-In Or Gate * PCM1702U SOP 20bit DA Converter * PCM1760U SOIC Dual 20bit Delta-Sigma Modulator * DF1760U SOIC Decimating Filter * TDA1309HN2 QFP Bitstream AD/DA Converter * 74HC125D SOIC Quad Tri-State Buffer * 74HC04D SOIC Hex Inverter * 74HC74D SOIC Dual Flip-Flop * 74HC374DW SOIC Octal D-Type Flip-Flop * 74HC08D SOIC Quad 2-Input And Gate * 74HC14D Soic Hex Inverter Schmitt Trigger * LM336Z 2.5V 10mA Voltage Reference * J176 TO92 P-Channel J-Fet Transistor * BC327 TO92 Pnp Transistor * BC337 TO92 Npn Transistor * PMLL4148 Smd 100mA 75V Signal Diode * 100K 1/4W 1% Metalized Film Resistor * 82K5 1/4W 1% Metalized Film Resistor * 12K1 1/4W 1% Metalized Film Resistor * 374E 1/4W 1% Metalized Film Resistor * 110E 1/4W 1% Metalized Film Resistor Note: Each spare part is single quantity unless otherwise specified. Asterisk prefix explanation: Omitted = First level spare part. One asterisk = Second level, part of previous listed first level part. Two asterisk = Third level, part of previous listed second level part. Three asterisk = ............ Any request for not above mentioned part must encompass specific description including: 1) Model name, 2) Section name, 3) Module code, 4) Reference name, 5) Quantity number.