Download htct180 service manual
Transcript
HT-CT180 SA-CT180 SERVICE MANUAL US Model Canadian Model AEP Model UK Model Australian Model Ver. 1.0 2015.02 • All of the units included in the HT-CT180 (SA-CT180/SA-WCT180/Remote control) are required to confirming operation of SA-CT180. Check in advance that you have all of the units. Photo: SA-CT180 Note: Be sure to keep your PC used for service and checking of this unit always updated with the latest version of your anti-virus software. In case a virus affected unit was found during service, contact your Service Headquarters. COMPONENT MODEL NAME HT-CT180 Bar Speaker (Active Speaker System) Subwoofer (Active Subwoofer) SA-CT180 SA-WCT180 • Please refer to service manual separately issued for Subwoofer. SPECIFICATIONS BLUETOOTH section Amplifier section U.S. models: POWER OUTPUT AND TOTAL HARMONIC DISTORTION: (FTC) Front L + Front R: With 4 ohms loads, both channels driven, from 200 Hz - 20,000 Hz; rated 13 Watts per channel minimum RMS power, with no more than 1% total harmonic distortion from 250 milliwatts to rated output. POWER OUTPUT (reference) Front L/Front R speaker: 25 Watts (per channel at 4 ohms, 1 kHz) Except US models: POWER OUTPUT (rated) Front L + Front R: 13 W + 13 W (at 4 ohms, 1 kHz, 1% THD) POWER OUTPUT (reference) Front L/Front R speaker: 25 Watts (per channel at 4 ohms, 1 kHz) Communication system BLUETOOTH Specification version 4.0 Output BLUETOOTH Specification Power Class 2 Maximum communication range Line of sight approx. 10 m (33 ft) 1) Maximum number of devices to be registered 8 devices Frequency band 2.4 GHz band (2.4000 GHz 2.4835 GHz) Modulation method FHSS (Freq Hopping Spread Spectrum) Compatible BLUETOOTH profiles 2) A2DP (Advanced Audio Distribution Profile) Supported Codecs 3) SBC 4) Transmission range (A2DP) 20 Hz - 20,000 Hz (Sampling frequency 44.1 kHz) Inputs OPTICAL ANALOG 1) The actual range will vary depending on factors such as obstacles between devices, magnetic fields around a microwave oven, static electricity, cordless phone, reception sensitivity, operating system, software application, etc. 2) BLUETOOTH standard profiles indicate the purpose of BLUETOOTH communication between devices. 3) Codec: Audio signal compression and conversion format 4) Subband Codec Speakers Front L/Front R speaker section Speaker system 2-way speaker system, Acoustic suspension Speaker Tweeter: 14 mm - 25 mm ( 9 / 16 in - 1 in) balance dome type Woofer: 40 mm × 120 mm (1 5 / 8 in × 4 3/ 4 in) cone type General Power requirements 120 V AC, 60 Hz (US and Canadian models) 220 V - 240 V AC, 50 Hz/60 Hz (AEP, UK and Australian models) Power consumption On: 17 W Standby mode: 0.5 W or less BLUETOOTH Standby mode: 3 W or less Dimensions (approx.) (w/h/d) 901 mm × 52 mm × 84 mm (35 1/ 2 in × 2 1/ 8 in × 3 3/ 8 in) Mass (approx.) 2 kg (4 lb 7 oz) Wireless transmitter Frequency band 2.4 GHz band (2.404 GHz - 2.476 GHz) Modulation method GFSK Supplied accessories Remote control (1) R03 (size AAA) batteries (2) Optical digital cable (1) Speaker pads for the subwoofer (4) Design and specifications are subject to change without notice. HT-CT180 SOUND BAR SA-CT180 ACTIVE SPEAKER SYSTEM 9-896-127-01 2015B33-1 © 2015.02 Sony Corporation Published by Sony Techno Create Corporation HT-CT180 Copyrights and Trademarks This system incorporates Dolby* Digital Surround System. * Manufactured under license from Dolby Laboratories. Dolby, and the double-D symbol are trademarks of Dolby Laboratories. The BLUETOOTH® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Sony Corporation is under license. The N Mark is a trademark or registered trademark of NFC Forum, Inc. in the United States and in other countries. Android™ is a trademark of Google Inc. “ClearAudio+” is a trademark of Sony Corporation. Other trademarks and trade names are those of their respective owners. SAFETY CHECK-OUT After correcting the original service problem, perform the following safety check before releasing the set to the customer: Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. LEAKAGE TEST The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microamperes.). Leakage current can be measured by any one of three methods. 1. A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers’ instructions to use these instruments. 2. A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. 3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The “limit” indication is 0.75 V, so analog meters must have an accurate low-voltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2 V AC range are suitable. (See Fig. A) To Exposed Metal Parts on Set 0.15 μF 1.5 kΩ AC voltmeter (0.75 V) Earth Ground Fig. A. Using an AC voltmeter to check AC leakage. SAFETY-RELATED COMPONENT WARNING! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. 2 ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ! LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY. HT-CT180 SECTION 1 SERVICING NOTES TABLE OF CONTENTS 1. SERVICING NOTES ............................................. 3 2. DISASSEMBLY 2-1. 2-2. 2-3. 2-4. 2-5. 2-6. 2-7. 2-8. 2-9. 2-10. 2-11. Disassembly Flow ........................................................... Rear Cabinet Block ......................................................... AC Cord (AC1) ............................................................... MAIN Board Block ........................................................ MAIN Board ................................................................... NFC Module ................................................................... LED Board ...................................................................... Antenna (ANT1) ............................................................. Loudspeaker (SP1, SP3) (L-ch) ...................................... BT NFC Board ................................................................ Loudspeaker (SP2, SP4) (R-ch) ...................................... 3. TEST MODE ............................................................ 16 4. DIAGRAMS 4-1. 4-2. 4-3. 4-4. 4-5. 4-6. 4-7. 4-8. 4-9. 4-10. 4-11. 4-12. 4-13. 4-14. Block Diagram ................................................................ Printed Wiring Board - MAIN Board - ........................... Schematic Diagram - MAIN Board (1/6) - ..................... Schematic Diagram - MAIN Board (2/6) - ..................... Schematic Diagram - MAIN Board (3/6) - ..................... Schematic Diagram - MAIN Board (4/6) - ..................... Schematic Diagram - MAIN Board (5/6) - ..................... Schematic Diagram - MAIN Board (6/6) - ..................... Printed Wiring Board - KEY Board -.............................. Schematic Diagram - KEY Board - ................................ Schematic Diagram - BT NFC Board -........................... Printed Wiring Board - BT NFC Board - ........................ Printed Wiring Board - LED Board - .............................. Schematic Diagram - LED Board -................................. 5. EXPLODED VIEWS 6 7 8 9 10 11 11 12 13 14 15 17 19 20 21 22 23 24 25 25 25 26 27 27 27 5-1. Rear Cabinet Section ...................................................... 32 5-2. Front Cabinet Section ..................................................... 33 6. ACCESSORIES ....................................................... 34 The SERVICING NOTES contains important information for servicing. Be sure to read this section before repairing the unit. UNLEADED SOLDER Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size) : LEAD FREE MARK Unleaded solder has the following characteristics. • Unleaded solder melts at a temperature about 40 °C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350 °C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! • Strong viscosity Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. • Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder. ADVANCE PREPARATION WHEN CONFIRMING OPERATION All of the units included in the HT-CT180 (SA-CT180/SAWCT180/Remote control) are required to confirming operation of SA-CT180. Check in advance that you have all of the units. DESTINATION ABBREVIATIONS The following abbreviations for model destinations are used in this service manual. • Abbreviations AUS : Australian model CND : Canadian model 3 HT-CT180 MODEL IDENTIFICATION Distinguish by Part No. on the bottom side of a main unit. Note: The printed contents of following figure model number label may be different from the model number label of a main unit. MODEL NUMBER LABEL US and Canadian models 4-559-553-0[] AEP model 4-559-554-0[] UK model 4-559-555-0[] Australian model 4-562-621-0[] – Bottom view – 4 HT-CT180 ABOUT PARTS REPAIR OF EACH BOARDS When each boards installed in this unit are defective, individual electrical parts that the mount is done cannot be replaced. When each boards are defective, replace the mounted board or the whole parts including an applicable board. Printed wiring board and schematic diagram that have been described on this service manual are for reference. (Printed wiring board and schematic diagram of WIERLESS board have not described) NOTE OF REPLACING THE BT NFC BOARD OR THE NFC MODULE When replacing the BT NFC board or the NFC module, be sure to replace both at the same time. The BT NFC board or the NFC module cannot replace with single. METHOD OF RESET If the system still does not operate properly, reset the system as follows: 1 2 While holding down the @/1 (on/ standby) button on the system, hold down the INPUT and VOL – buttons simultaneously for 5 seconds. All 5 indicators on the Bar Speaker flash 3 times, and the settings return to their initial status. Disconnect the AC power cord (mains lead). WHAT TO DO IF PROTECT If all of the LEDs are lit, it is state in the protect. This state shows an abnormality of the AMP circuit. In this case, there is a possibility that the MAIN board is defective. Please replace the MAIN board. NOTE OF REPLACING THE WIRELESS BOARD When replaced the WIRELESS board, link of SA-CT180 and SAWCT180 will be disconnected. Before you return repaired unit to customers, please link the SACT180 and SA-WCT180 by the following procedure. If, in a state in which only one of SA-CT180 or SA-WCT180 is brought into service field, and replaced the WIRELESS board of SA-CT180 or SA-WCT180, when returning the repaired unit, be sure to inform the customers that it is necessary to link the following procedure. Enabling the Secure Link function You can specify the wireless connection to link the Bar Speaker to the subwoofer using the Secure Link function. This function can help prevent interference if you use multiple wireless products or your neighbors use wireless products. 1 2 Press LINK on the rear of the subwoofer. You will hear beeps from the subwoofer. Hold down PAIRING on the Bar Speaker for 5 seconds, then VOL – for 5 seconds. The OPTICAL and ANALOG indicators flash alternately. When the Bar Speaker is linked to the subwoofer, the indicators stop flashing. If it failed, the indicators light up for 5 seconds. Try again the above operation. 5 HT-CT180 SECTION 2 DISASSEMBLY • This set can be disassembled in the order shown below. 2-1. DISASSEMBLY FLOW SET 2-2. REAR CABINET BLOCK (Page 7) 2-3. AC CORD (AC1) (Page 8) 2-4. MAIN BOARD BLOCK (Page 9) 2-6. NFC MODULE (Page 11) 2-5. MAIN BOARD (Page 10) 2-7. LED BOARD (Page 11) 2-10. BT NFC BOARD (Page 14) 2-8. ANTENNA (ANT1) (Page 12) 2-11. LOUDSPEAKER (SP2, SP4) (R-CH) (Page 15) 2-9. LOUDSPEAKER (SP1, SP3) (L-CH) (Page 13) 6 HT-CT180 Note: Follow the disassembly procedure in the numerical order given. 2-2. REAR CABINET BLOCK 4 rear cabinet block Right side 3 KEY board cable connector (XP3) 1 thirteen screws (3 u 10 B) 2 Lift up the rear cabinet block in the direction of the arrow. Note: Please spread a sheet under a unit not to injure front cabinet. Left side Top side Bottom side :LUHVHWWLQJ groove – Rear top view – –5HDUFDELQHWEORFNIURQWYLHZ– rib wire OK The wire and rib are separated. rib NG The wire and rib are overlapping. wire 7 HT-CT180 2-3. AC CORD (AC1) cord bush 2 claw 2 claw – Front cabinet rear view – 1 AC cord connector (CN501) Bottom side Left side Top side 4 AC cord block Note 1: Please spread a sheet under a unit not to injure front cabinet. – Rear top view – hole 7 AC cord (AC1) 3 Draw the AC cord block out of the hole in rear cabinet block. 5 claw 6 cord bush How to install the cord bush Note 2: When installing the cord bush to the AC cord (AC1), check the directions of the white line of the AC cord (AC1) and the claw of the cord bush, and install correctly. AC cord (AC1) [white line] claw cord bush Installation direction for the cord bush cord bush claw 65 ± 5 mm Note 3: Make sure that the white line is at the bottom. – Front cabinet rear view – 8 HT-CT180 2-4. MAIN BOARD BLOCK 7 antenna wire terminal 3 two screws (3 u 8 S) Right side 5 FFC 22P (FFC2) (XS1) 9 MAIN board block 6 R-ch speaker cable connector (XP11) 8 L-ch speaker cable connector (XP10) 2 NFC cable connector (XP12) Bottom side 1 FFC 10P (FFC1) (XP20) Top side 4 Lift up the MAIN board block in the direction of the arrow. Left side –)URQWFDELQHWEORFNUHDUWRSYLHZ– front side Install the antenna wire straight from the front side. groove groove groove connector colored line connector :LUHVHWWLQJ FFC 22P (FFC2) OK Insert straight into the interior. flexible flat cable colored line NG Insert at a slant. flexible flat cable Note: Please spread a sheet under a unit not to injure front cabinet. speaker wire How to install the flexible flat cable When installing the flexible flat cable, ensure that the colored line is parallel to the connector after insertion. speaker wire WIRELESS board –)URQWFDELQHWEORFNUHDUYLHZ– NG OK The FFC is goes around the parts. –7RSYLHZ– FFC 10P (FFC1) The FFC goes in between the parts. –7RSYLHZ– FFC 10P (FFC1) 9 HT-CT180 2-5. MAIN BOARD 2 WIRELESS board Note 1: When WIRELESS board is replaced, refer to “NOTE OF REPLACING THE WIRELESS BOARD” on page 5. 4 cushion (A) (See Fig. A) 7 four screws (3 u 6 B) 5 cushion (B) (See Fig. A) 0 MAIN board 6 cushion (EVA) (See Fig. B) 1 connector (XP7) 7 two screws (3 u 6 B) 3 cushion (C) (See Fig. A) 9 sheet (IC) (See Fig. C) 8 Remove the MAIN board block in the direction of the arrow. 3 cushion (C) (See Fig. A) –0$,1ERDUGEORFNIURQWYLHZ– 3DVWLQJSRVLWLRQRIFXVKLRQV Note 2: When replacing the MAIN board, make sure to affix these cushions and the sheet. The cushions and the sheet are supplied as a set. < Fig. A> cushion (C) MAIN board MAIN board screw (3 u 6 B) 1 ± 0.5 mm MAIN board cushion (C) cushion (A) 1 ± 0.5 mm guide line cushion (B) MAIN board –7RSYLHZ– cushion (B) cushion (C) cushion (B) cushion (A) guide line cushion (C) –0$,1ERDUGEORFNUHDUYLHZ– < Fig. B> < Fig. C> sheet (IC) IR602 guide line guide line cushion (EVA) MAIN board guide line –)URQWYLHZ– 10 cushion (EVA) metal panel –0HWDOSDQHOWRSYLHZ– HT-CT180 2-6. NFC MODULE Note 1: When replacing the BT NFC board or the NFC module, be sure to replace both at the same time. The BT NFC board or the NFC module cannot replace with single. 2 screw (3 u 8 S) 1 connector (XP12) 5 NFC module 4 NFC bracket +RZWRLQVWDOOWKH1)&PRGXOH Note 3: When installing the NFC module to the NFC bracket, install so that the solder portion of the wire is positioned as shown in the figure below. 3 Peel off the adhesive sheet. NFC bracket solder portion Bottom side Left side Note 2: Please spread a sheet under a unit not to injure front cabinet. Top side – Front cabinet block rear top view – 2-7. NFC module – NFC module block bottom view – LED BOARD 1 FFC 10P (FFC1) (XP5) How to install the flexible flat cable When installing the flexible flat cable, ensure that the colored line is parallel to the connector after insertion. terminal side 2 two screws (3 u 8 S) Right side 3 LED board OK Insert straight into the interior. flexible flat cable colored line connector NG Insert at a slant. flexible flat cable colored line connector Note: Please spread a sheet under a unit not to injure front cabinet. Bottom side – Front cabinet block rear bottom view – Left side 11 HT-CT180 2-8. ANTENNA (ANT1) :LUHVHWWLQJ three grooves three grooves antenna wire groove Note 2: Pass the antenna wire between the loudspeaker and the front cabinet block. woofer (L-ch) tweeter (L-ch) Right side 1 Peel off the adhesive sheet. Note 1: Please spread a sheet under a unit not to injure front cabinet. 2 antenna (ANT1) Bottom side Left side –)URQWFDELQHWEORFNUHDUERWWRPYLHZ– 12 HT-CT180 2-9. LOUDSPEAKER (SP1, SP3) (L-CH) 6SHDNHUFRUGVHWWLQJ/FK terminal (wide side) [red] Note 2: Pass the speaker cord over the top of the loudspeaker (SP2). terminal (narrow side) [black] 2 speaker cord 1 terminal (narrow side) [black] 1 terminal (wide side) [red] 3 four screws (3 u 8 S) loudspeaker (SP1) 4 loudspeaker (4.3 u 12 cm) (SP1) terminal (narrow side) [black] terminal (wide side) [red] loudspeaker (SP3) 1 terminal (narrow side) [black] 5 screw (2.6 u 8 S) 1 terminal (wide side) [red] 5 screw (2.6 u 8 S) 6 loudspeaker (1.4 u 2.5 cm) (SP3) Right side Note 1: Please spread a sheet under a unit not to injure front cabinet. Bottom side – Front cabinet block rear bottom view – Left side ,QVWDOODWLRQGLUHFWLRQIRUWKHORXGVSHDNHU4.3 × 12 FP63 terminal (wide side) [red] top side terminal (narrow side) [white] How to install the speaker terminal Insert the speaker terminal straight into the interior. There is a possibility that using this unit without the speaker terminal correctly installed will damage it. OK Insert straight into the interior. speaker cord speaker terminal loudspeaker (SP1) – Front cabinet block rear view – NG nsert only part way. speaker cord speaker terminal 13 HT-CT180 2-10. BT NFC BOARD Note 1: When replacing the BT NFC board or the NFC module, be sure to replace both at the same time. The BT NFC board or the NFC module cannot replace with single. :LUHVHWWLQJ Right side Top side tweeter (R-ch) BT NFC board Bottom side +RZWRLQVWDOOWKHIOH[LEOHIODWFDEOH When installing the flexible flat cable, ensure that the colored line is parallel to the connector after insertion. Note 3: Pass the FFC 22P (FFC2) between the loudspeaker and the front cabinet block. Left side 2 FFC 22P (FFC2) (XP19) terminal side Left side 3 BT NFC board NG Insert at a slant. flexible flat cable Bottom side colored line connector Note 2: Please spread a sheet under a unit not to injure front cabinet. Right side –)URQWFDELQHWEORFNUHDUERWWRPYLHZ– 14 FFC 22P (FFC2) 1 Remove the BT NFC board block straightly in the direction of the arrow. OK Insert straight into the interior. flexible flat cable colored line connector woofer (R-ch) HT-CT180 2-11. LOUDSPEAKER (SP2, SP4) (R-CH) 6SHDNHUFRUGVHWWLQJ5FK terminal (narrow side) [black] loudspeaker (SP4) terminal (narrow side) [black] terminal (wide side) [red] Note 2: Pass the speaker cord over the top of the loudspeaker (SP2). loudspeaker (SP2) terminal (wide side) [red] +RZWRLQVWDOOWKHVSHDNHUWHUPLQDO Insert the speaker terminal straight into the interior. There is a possibility that using this unit without the speaker terminal correctly installed will damage it. OK Insert straight into the interior. speaker cord speaker terminal 2 speaker cord 1 terminal (wide side) [red] 3 screw (3 u 8 S) 1 terminal (narrow side) [black] 3 three screws (3 u 8 S) 1 terminal (narrow side) [black] 4 loudspeaker (4.3 u 12 cm) (SP2) NG nsert only part way. speaker cord speaker terminal 1 terminal (wide side) [red] 5 screw (2.6 u 8 S) 5 screw (2.6 u 8 S) Left side 6 loudspeaker (1.4 u 2.5 cm) (SP4) Note 1: Please spread a sheet under a unit not to injure front cabinet. ,QVWDOODWLRQGLUHFWLRQIRUWKHORXGVSHDNHU×FP63 top side Right side Bottom side terminal (narrow side) [white] terminal (wide side) [red] –)URQWFDELQHWEORFNUHDUERWWRPYLHZ– loudspeaker (SP2) –)URQWFDELQHWEORFNUHDUYLHZ– 15 HT-CT180 SECTION 3 TEST MODE VERSION DISPLAY The check of the software version can be performed. Procedure: 1. Press the [@/1] button to turn the power on. 2. Press three buttons of the [INPUT], [VOL+] and [VOL−] simultaneously for 2 seconds. 3. When enter the version display mode, the software version is shown by the frequency of blinking of each LED. LED showing the software version DEMO MODE The demo mode can be performed. (This mode is used by shop front) Procedure: 1. Press the [@/1] button to turn the power on. 2. Press two buttons of the [INPUT] and [VOL−] simultaneously for 5 seconds. 3. When enter the demo mode, ANALOG function LED is blink twice quickly, then changed to the setting of initial value for demo mode. blink twice quickly Software version X.XX Minor version (Lower) (BLUETOOTH function LED) Minor version (Upper) (ANALOG function LED) Major version (OPTICAL function LED) Example: When the software version is “1.02” OPTICAL function LED is blink once. ANALOG function LED is not blink. BLUETOOTH function LED is blink twice. 4. When the version display is finished, return to the normal mode. FACTORY RESET It can clear all settings and the Bluetooth pairing history to initial conditions. Execute this mode when returning this unit to the customer. Procedure: 1. Press the [@/1] button to turn the power on. 2. Press three buttons of the [INPUT], [VOL−] and [@/1] simultaneously for 5 seconds. 3. Blink three times all LEDs, then lights up all LEDs. When the reset is complete, all LEDs light off and becomes the standby status. 16 Initial value for demo mode: Function : OPTICAL Volume : 25 Muting : OFF Sound field : CLEAR AUDIO+ Night mode : OFF Voice : OFF Subwoofer volume : 10 Dual mono : MAIN Note 1: When demo mode is “ON”, the operation of the [@/1] button on the unit, and the operation of the [@/1] and [INPUT] buttons on the remote commander is invalid. Note 2: When the non-operation and no sound for five minutes is followed, setting will return to the initial value for demo mode. Releasing method: Perform the “FACTORY RESET”. Note: The demo mode does not release by unplug the AC cord. HT-CT180 SECTION 4 DIAGRAMS 4-1. BLOCK DIAGRAM Wireless Module IA2S4M Optical In AUDIO_IN ADC AK5358 TAS3157*2 TBMC830 DATA3 MCLK BCLK LRCLK I/O BCLK1 MCLK LRCLK1 I/O NFC NFC-FS2 SPI FLASH 16M DATA0 MTK8301 BTL IIC2 REST BCLK2 LRCLK2 DATA1 4ɏ 25W THD 30% Audio Processor STA339BW IIC1 SPI1 BTL SDRAM IR 27M 01U0IRR CV-102 crystall DC-DC 16.5V STB_3.3V STB 3 3V STB_3.3V 16.5V DC-DC EUP3482A 16.5V HT-CT180 5V For IA2S4M ˈAK5358, TAS3157*2, F4558*1, power LED *5 5 signal )RUMTK8301Ƚ)ODVKȽSDRAMǃIRǃ NFCǃ TBM-C830 EUP3482A POWER SUPPLY KEY *5 5 STB_3.3V 4ɏ 25W THD 30% LDO CW1117 Switch G9012M 1 25V 1.25V 3.3V )RU 67$%: )RU67$%: 17 17 )RU07. )RU67$%:Ƚ/(' Ƚ237 HT-CT180 THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) For Printed Wiring Boards. For Schematic Diagrams. Note: • : Pattern from the side which enables seeing. (The other layers’ patterns are not indicated.) Note: • All capacitors are in μF unless otherwise noted. (p: pF) 50 WV or less are not indicated except for electrolytics and tantalums. • All resistors are in Ω and 1/4 W or less unless otherwise specified. Caution: Pattern face side: (Conductor Side) Parts face side: (Component Side) Parts on the pattern face side seen from the pattern face are indicated. Parts on the parts face side seen from the parts face are indicated. Note: The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. • Circuit Boards Location LED board Note: Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. NFC module WIRELESS board MAIN board BT NFC board KEY board HT-CT180 18 18 HT-CT180 4-2. PRINTED WIRING BOARD - MAIN Board 1 2 3 • See page 18 for Circuit Boards Location. 4 5 6 • : Uses unleaded solder. 7 8 MAIN BOARD (COMPONENT SIDE) A B C D MAIN BOARD (CONDUCTOR SIDE) E F HT-CT180 19 19 9 10 11 12 13 14 HT-CT180 SCHEMATIC DIAGRAM - MAIN Board (1/6) - 1 3 4 5 6 7 8 MAIN BOARD (1/6) HV 1M LIF501 2 1M RV501 CN501 FB502 2PIN/7.92mm F501 T3.15AL250V TR501 FB90@100MHz CE502 4 - VDR/620VR502B R502D 470pF/250VAC CY501 1M 1M + + 1 82uF/450V 3 1 2 1 2 KBP306 BD1 LIF4-22-15 470pF/250VAC CY502 2 FB504 FB90@100MHz R502C 4 R502A 1 A 2 • See page 28 for IC Block Diagrams. 3 4-3. C537 NC/1500pF/1KV FB501 CX501 FB90@100MHz NTC/3ohm/5A 0.33uF/250VAC B CY507 HV 220pF/250VAC CY506 220pF/250VAC C533 1500pF/1KV R569 0 R570 0 T502 EF25 HV VDD 1 VDD D533 A9 A122 MUR420/4A/200V 8 9 C531 1500pF/1KV C MUR420/4A/200V 3 R572 R565 22 2M R571 150K + R566 22 D 7 R510 NC U531 D D A12 A13 11 12 6 ZD536 NC V R544 68.1K/1% P-GND R541 1.5K 0.1uF/50V/X7R CE532 + ZD535 47uF/35V 100 NC/BZX79C27 * CAUTION : ARE IMPORTANT PARTS ON THE SAFETY. PLEASE USE THE PARTS HAVING THE DESIGNATED PARTS NUMBER WITHOUT FAIL. HT-CT180 20 20 C534 0.1uF/50V/X7R U533 1 ZD531 BZX79C12 3 R533 0 R543 100K 2 3 CE531 + 47uF/35V C532 C535 220pF/50V/X7R U532 LTV-817S R539 E R542 3.3K R538 5.6 4 X F C549 0.1uF/50V/X7R FR104/1A/400V C 100pF/1KV THE PARTS MARKED WITH + GND FB R540 D532 15 C536 F CE533 470uF/35V FB CONTROL TOP256EN S 4 CE535 470uF/25V D531 FR207/2A/1000V R537 2M D R567 150K R568 150K 2 150K N.C 1 R536 +18V AS431 R557 12.1k/1% R546 100K ZD533 NC HT-CT180 4-4. SCHEMATIC DIAGRAM - MAIN Board (2/6) - 1 A 2 • See page 28 for IC Block Diagrams. 3 4 5 6 7 8 MAIN BOARD (2/6) STB_3V3 R3 10K POWER_18V Vout=0.923(R1+R2/R2) 600/2A input Vout FB EUP3482ADIR1 3 5 100pF FB=0.923V C11 3300pF//50V/X7R C152 R10 150 ohm 39.2K/1% CE25 + C236 SW R96 7.5K/1% R97 7.5K/1% 7.5K 2 4 1 NC/10uF/10V/X7R 0.1uF/25V/Y5V R19 C80 NC/120/1% 10uF/10V/X7R 1uF 1.25V C24 C79 Out 0 0.1uF SS NC EN 100UF/25V 22K 8 D542 C7 1V2 R18 C23 C199 4.7uF/16V/Y5V ADJ/GND 3 R16 10uH/2A 10uF/10V/X7R C L1 1 2 7 R6 0.1uF/25V/Y5V U4 AS1117 0.01uF R57 C10 STB_3V3 STB_3V3 R99 IN 220uF35V C6 U2 C75 330pF/50V/NP0 NC/0.1uF 1uF/50V/X7R 56 C4 C200 + BS C3 R5 47K COMP 10K R1 CE7 GND FB19 0.1uF/25V/Y5V 4 POWER_ON 0.1uF 10K C12 C234 R9 B Rate : 2A 30V 160m 340KHz In Range: 4-30V Out Range: 0.923V-12V 0.1uF R8 AMP_VCC TP43 Close to U2_EUP3482A Q1 NPN_3DG3904M EN2 6 POWER_18V EN2 C16 0.01uF HT-CT180 R21 560 0.1uF/25V/Y5V C25 EN2 0.1uF/25V/Y5V R81 100pF FB=0.923V 3300pF//50V/X7R C162 R95 150 ohm CE27 + 51K/1% C255 D543 5 R120 1K/1% R121 7.5K 21 10K/1% 0.1uF 3 100UF/25V C19 NC 1 BS COMP FB 6 IN GND 2 21 SW SS 4 0.1uF 100 EN EUP3482ADIR1 0.1uF/25V/Y5V E 22K 8 C18 C755 POWER_ON R122 10uH/1A R123 10uF/10V/X7R 7 C20 Q3 PNP_3CG9012M R774 L2 R115 U3 C82 330pF/50V/NP0 10UF/25V/X7R 10UF/25V/X7R SYS_3V3 C17 SYS_5V C237 56 STB_3V3 Vout=0.923(R1+R2/R2) C15 0.1uF D Close to U2_EUP3482A 0 R25 C116 0 HT-CT180 SCHEMATIC DIAGRAM - MAIN Board (3/6) - 1 2 3 4 5 7 8 9 MAIN BOARD (3/6) A_1V2 A_1V2 Mute AMP_FAULT AMP_SCL AMP_SDA LED3 LED4 LED1 LED4 MTK_DATA1 A_3V3 TX2+ A_3V3 R202 R201 SUB_SDA SUB_SCL A_3V3 33 33 33 33 129 E-PAD/GND MTK_DATA0 R59 MTK_DATA1 R61 D_1V2 TX1+ TX1- TXC+ TXCR51 0 R52 1.5K/1% R53 D_1V2 R82 D_1V2 M_A3 M_A2 M_A1 M_A0 M_A10 BA1 BA0 D_3V3 RAS CAS RWE M_A4 M_A5 M_A6 1K BT_Pairing POWER_ON 10K D_3V3 M_A7 M_A8 22pF/50V/NP0 SDCLK AMP_RST1 Mute R73 R74 R75 R76 10PF/50V/NP0 10PF/50V/NP0 4 C61 2 33 33 33 33 AMCLK ABCLK ALRCLK ADATA AMCLK ABCLK ALRCLK ADATA 4.7K SUB_SDA SUB_SCL SUB_IIC_BUSY 22 22 R119 1/2power_control AMP_FAULT R125 AMP_SCL AMP_SDA 33 AMP_RST Mute NC/33 1/2power-control AMP_FAULT R101 4.7K SUB_SDA SUB_SCL SUB_IIC_BUSY TP1 TXC+ TXC+ TP2 TXC- TXC- TP3 TX0+ TX0+ TX0- TX0- TX1+ TX1+ TX1- TX1- TP4 TP5 TP6 TX2+ TP7 TX2- TP8 TP9 TP10 NC/0 HT-CT180 C62 Put these Compnonents as closer as possible to MT8307 R90 4.7K SF_3V3 SF_CK R28 0 SF_DI R30 0.1uF/25V/Y5V 8 CE# VDD 7 SO HOLD# 6 WP# SCK 5 VSS SI SPI_16Mb_EN25T160 C64 10PF/50V/NPO 4.7K 4.7K 0.1uF/25V/Y5V XO AMP_SCL AMP_SDA AMP_SCL AMP_SDA 10PF/50V/NP0 R88 R89 C65 F C66 U7 33 27pF/50V/NP0 SF_3V3 1 2 3 4 R84 C63 0 SF_CS SF_DO 1 BT_RESET BT_STATUS2 BT_FN BT_POWER_CONTROL BT_PIO7 BT_STATUS1 TP12 TP13 33 C59 25mA 27pF/50V/NP0 R34 SF_3V3 IR NFC_INT MP3_BT_SW R72 C60 STB_3V3 LED3 LED1 BT_RESET BT_STATUS2 BT_FN BT_POWER_CONTROL BT_PIO7 BT_STATUS1 AD_MCLK AD_BCLK AD_LRCK AD_DATA 1M VOL+ VOLFUNCTION LED3 LED1 NFC_INT MP3_BT_SW E 3 10K VOL+ VOL- IR R94 R83 AMP_DATA0 AMP_DATA1 R381 R380 SYS_3V3 XI AMP_DATA0 AMP_DATA1 33 33 SYS_3V3 M_A11 M_A9 DQ13 DQ12 DQ11 DQ10 DQ9 DQ8 UDQM DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 LDQM DQ15 DQ14 D_3V3 4PIN/2.0mm SDCLK SD_3V3 M_A11 M_A9 M_A8 M_A7 M_A6 M_A5 M_A4 D_3V3 1K/1% MT8301_OQE LQFP128-630630-0.4-88D5100 C72 TP18 UDQM SD_CLK R42 4.7K R370 10K TX0+ TX0- DV_C1 DV_C2 DV_C3 SD_MS_D2 SD_MS_D3 GPIO13 GPIO9 GPIO8 GPIO7/CKE_ DVDD33 RD0 RD1 RD2 RD3 RD4 RD5 RD6 RD7 DQM0 RD15 RD14 DVDD12 RD13 RD12 RD11 RD10 RD9 RD8 DQM1 RCLK RA11 RA9 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 BT_RESET BT_STATUS2 BT_POWER_CONTROL BT_PIO7 33 R93 AMP_RST1 BT_STATUS1 BT_FN MP3_BT_SW NC/0.1uF/25V/Y5V 1 2 3 4 SD_3V3 DQ8 NC/15pF/50V/NP0 DSP_RXD DSP_TXD XP2 DQ10 DQ9 C33 1 2 3 4 SD_3V3 DQ12 DQ11 10PF/50V/NP0 TP14TP15TP16 TP17 STB_3V3 DQ14 DQ13 10PF/50V/NP0 STB_3V3 DQ15 C50 10K 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 C51 10K STB_3V3 100pF/50V/NP0 R371 R369 R64 100pF/50V/NP0 0.1uF/25V/Y5V R63 1K 1K 4.7K C273 0.1uF/25V/Y5V 4.7K 33 VSS DQ15 VSSQ DQ14 DQ13 VDDQ DQ12 DQ11 VSSQ DQ10 DQ9 VDDQ DQ8 VSS NC UDQM CLK CKE NC A11 A9 A8 A7 A6 A5 A4 VSS C77 0.1uF/25V/Y5V IR R70 NFC_INT R963 FUNCTION R962 POWER V1.0 U5 VDD DQ0 VDDQ DQ1 DQ2 VSSQ DQ3 DQ4 VDDQ DQ5 DQ6 VSSQ DQ7 VDD LDQM WE CAS RAS CS BA0 BA1 A10/AP A0 A1 A2 A3 VDD SYS_3V3 TX2- 0.1uF/25V/Y5V 1.2K/1% 1.2K/1% C274 C58 0.1uF/25V/Y5V 0.1uF/25V/Y5V C57 500/500mA C78 C56 0.1uF/25V/Y5V 0.1uF/25V/Y5V 0.1uF/25V/Y5V C54 4.7uF/16V/Y5V C55 FB8 R67 R68 LQFP 128 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 4.7uF/16V/Y5V 1K SF_CK TX2N AVDD12_D TX1P TX1N AVSS12 TX0P TX0N AVDD12_C TXCP TXCN AVDD33_12 EXT_RES GPIO10/HPLG SPDIF/GPIO12 DVDD12 RA3 RA2 RA1 RA0 RA10 BA1 BA0 DVDD33 RAS_ CAS_ RWE_ RA4 RA5 RA6 DVDD33 RA7 RA8 MT8307 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 SDRAM_64Mb_M12L64164A-7T C44 D_3V3 AVDD12_2 AVDD33_1 XTALI XTALO V14 GPO5 AVDD33_2 NC NC GPIO2 USB_DP USB_DM VDD33_USB PAD_VRT VDD12_USB DV_Y2 DV_Y3 DV_Y4 SF_CS SF_DO SF_DI DVDD33 SF_CK UP1_6/SCL UP1_7/SDA GPIO11 GPIO6 PRST_ IR_ GPIO3/INT_ GPIO4 DV_C0 LDQM R40 0 R47 0 R48 0 R43 4.7K R44 0 R45 0 M_A10 M_A0 M_A1 M_A2 M_A3 SD_3V3 C45 100pF/50V/NP0 DQ5 DQ6 BA0 BA1 100pF/50V/NP0 C279 SD_3V3 C275 SF_CS SF_DO SF_DI DQ3 DQ4 33 33 33 C278 DQ1 DQ2 100pF/50V/NP0 RWE CAS RAS 560 100pF/50V/NP0 5.1K/1% D_1V2 1K C28 C53 C52 D R55 SPDIF_OPT DQ0 SD_3V3 R36 STB_3V3 USB_DP USB_DM USB_DP USB_DM 1K STB_SD_3V3 500/200mA LED2R199 33 A_3V3 1/2power_control 33 33 FB7 SD_3V3 XI XO LED2 HDMI_SCL HDMI_SDA DSP_RXD DSP_TXD 8301_RST R49 STB_SD_3V3 R964 10uF/10V/Y5V VOL+ R965 0.1uF/25V/Y5V 4.7uF/16V/Y5V 0.1uF/25V/Y5V 0.1uF/25V/Y5V 0.1uF/25V/Y5V 0.1uF/25V/Y5V 0.1uF/25V/Y5V C37 C38 C36 C35 C41 22uF/6.3V/X5R 22uF/6.3V/X5R 4.7uF/16V/Y5V VOL- C40 D_3V3 500/200mA C43 C42 STB_SD_3V3 D_3V3 C39 C159 0.1uF/25V/Y5V C157 0.1uF/25V/Y5V 0.1uF/25V/Y5V C158 0.1uF/25V/Y5V C31 4.7uF/16V/Y5V C156 0.1uF/25V/Y5V C32 D_3V3 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 A_1V2 A_3V3 A_1V2 A_3V3 10uF/10V/X7R A_3V3 500/200mA R38 R37 A_1V2 A_3V3 FB5 D_3V3 C30 1K 0.1uF/25V/Y5V R33 C117 0 R39 R69 R54 C29 C809 22uF/6.3V/X5R NPN_3DG3904M R112 SD_3V3 DQ7 R204 R203 22K 0.1uF/25V/Y5V STB_SD_3V3 C807 C806 10PF/50V/NP0 33 33 R24 10K 0.1uF/25V/Y5V Q5 Q4 NPN_3DG3904M 4.7K/1% C49 0.1uF/25V/Y5V 3.9K/1% R27 C48 0.1uF/25V/Y5V C160 0.1uF/25V/Y5V C47 R26 close to IC pin U6 FB4 C179 TP19 MTK_DATA0 ALRCLK R77 R205 SUB_IIC_BUSY R23 15K 8301_RST D_1V2 C46 B R22 D_1V2 500/500mA 10PF/50V/NP0 STB_3V3 1V2 FB6 150mA C177 D_1V2 0.1uF/25V/Y5V 0.1uF/25V/Y5V 22uF/6.3V/X5R 22uF/6.3V/X5R MTK_DATA0 => L, R MTK_DATA1 => Wireless SUB ADATA C27 500/500mA C26 FB9 ABCLK AMCLK 1V2 C808 C805 C 6 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 104 103 102 101 100 99 98 97 A • See page 28 for IC Block Diagrams. • See page 29 for IC Pin Function Description. NC AVDD12 ADACVDD2 ADACVDD1 ASDATA0 ALRCK AL/GPIO AVCM AR/GPIO0 ABCK LFE/GPIO ADACVSS APLLCAP/GPIO35 APLLVDD_GPIO/GPIO34 AADVDD AKIN1/GPIO21 ADVCM/GPIO20 AKIN2/GPIO19 NC NC AGND12 AVDD33 NC FS VREF/GPIO14 AVDD33 GPIO33 GPIO32 GPIO31 GPIO30 GPIO29 TX2P 4-5. HDMI_SDA HDMI_SCL TX2+ TX2BT_LED1 BT_LED2 HT-CT180 SCHEMATIC DIAGRAM - MAIN Board (4/6) - 1 3 4 5 6 7 8 P5V MP3_L 500/200mA IR 7.5K C801 AGND MP3-R 1 4.7UF/10V/X5R 2 ESD10 1 1 2 C619 C620 47pF/50V/NP0 VCC GND R133 B1 A R13 6 1K MP3_BT_SW 5 4 C802 100pF/50V/NP0 C96 MP3_L C74 SYS_3V3 AGND AGND 10PIN/0.5mm NC/2200pF//50V/X7R R118 7.5K C803 AGND MP3-L 1 4.7UF/10V/X5R 2 U22 3 R134 BT_L GND VCC B1 A 1 2 3 4 5 6 7 8 9 10 11 12 13 14 6 5 4 C804 10uFADC_INL C100 74LVC1G3157GV MP3&BT Switch Circuit 5.6K/1% C S B2 AGND SYS_5V 1 2 3 4 5 6 7 8 9 10 11 12 13 14 R80 R387 R386 R385R388R373R375 0 10K XP20 SYS_3V3 AMCLK SUB_IIC_BUSY 500/200mA 10uF/10V/Y5V 10PF/50V/NPO 0.1uF/25V/Y5V 33 SUB_SDA R151 33 SUB_SCL U11 1 2 3 4 5 6 7 8 AINR AINL CKS1 VCOM AGND VA VD DGND CKS0 CKS2 DIF PDN SCLK MCLK LRCK SDTO 16 15 14 13 12 11 10 9 AD_BCLK AD_MCLK AD_LRCK AD_DATA AD_BCLK AD_MCLK AD_LRCK AD_DATA ADC_AK5358A Slave 0.1uF/25V/Y5V R919 R152 C301 C81 100pF/50V/NP0 15PF C299 C306 C300 15PF 15PF 15PF 0 2.2 AGND C108 10uF/10V/X7R 0 0 0 R35 C109 FB12 ADC_INR ADC_INL R127 R128 R129 AMP_DATA1 ALRCLK ABCLK NC/33 10mA 4.7K 4.7K 4.7K 33 33 33 R149 100uF/16V/SMD R146 R148 R147 SYS_5V C303 XP7 20pin/2.0mm 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 R912 R913 R914 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 + C103 4.7 CE11 R124 0.1uF/25V/Y5V R915 R916 R917 R918 SYS_3V3 2.2uH/30mA AGND 23 23 100pF/50V/NP0 L5 0 0 0 0 C304 HT-CT180 SYS_5V R150 4.7K C302 F 1.5V 2.NC 3.NC 4.GND 5.GPIO 33 6.GPIO 26 7.GPIO 17 8.I2C_DAT 9.GND 10.I2C_CLK 11.I2S_DATI 12.I2S_LRCK 13.I2S_BCK 14.GPIO 31 15.I2S_MCLK 16.GND 17.GPIO 1 18.GPIO 2 19.GPIO 3 20.I2C_Busy 100pF/50V/NP0 20mA SYS_3V3 11 12 13 14 15 16 17 18 19 20 1 2 3 4 5 6 7 8 9 10 C91 C812 4.7UF/10V/X5R C88 0.1uF/25V/Y5V 100pF/50V/NP0 100pF/50V/NP0 100pF/50V/NP0 100pF/50V/NP0 C262 100pF/50V/NP0 C258 100pF/50V/NP0 C261 C250 100pF/50V/NP0 100pF/50V/NP0 C249 100pF/50V/NP0 C256 C247 100pF/50V/NP0 100pF/50V/NP0 C248 100pF/50V/NP0 C246 C251 C245 33pF/50V/NP0 100pF/50V/NP0 C257 C252 33pF/50V/NP0 C253 AGND C621 POWER FUNCTION BT_Pairing VOL+ VOL- 100pF/50V/NP0 POWER INPUT BT_Pairing VOL+ VOL- 100pF/50V/NP0 AGND BT_NFC 100pF/50V/NP0 500/200mASTB_SD_3V3 BT_NFC NC/33 C86 FB21 SYS_5V BT_FN BT_STATUS1 BT_RESET BT_PIO7 BT_POWER_CONTROL BT_STATUS2 C85 BT_FN BT_STATUS1 BT_RESET BT_PIO7 BT_POWER_CONTROL BT_STATUS2 C87 0 33 33 33 33 33 33 C89 2.2uF R911 R98 R100 R103 R104 R105 R106 BT_R BT_L 100pF/50V/NP0 33 33 R107 C254 XS1 R109 R108 C90 D 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0.1uF/25V/Y5V 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 C22 AGND 10K 10K 10K 10K 10K LED1 LED2 BT_LED1 BT_LED2 LED3 LED4 AGND 22PIN/0.5mm C811 C810 C98 C99 74LVC1G3157GV AGND SYS_3V3 100 10uF ADC_INR 5.6K/1% SPDIF_OPT 4 P5V 10 10K 10uF/16V/X7R SPDIF_OPT 10 S B2 3 BT_R C925 10uF/10V/Y5V R640 1 2 3 IR R11 U21 NC/2200pF//50V/X7R R46 C227 C111 0.1uF +5V SPDIF_IN 10 IR GND VCC 100pF/50V/NP0 C95 MP3_R R778 R138 MP3-L IR602 U12 1 BT_L SYS_5V AGND AGND 2 MP3-R AGND AGND 3 STB_3V3 R137 IRM BT_R 22uF/6.3V/X5R 2 CE363 47uF/SMD R78 + 100K IR 1M 22uF/6.3V/X5R C183 1M 1M R410 0.1uF/25V/Y5V C182 100pF/50V/NP0 B 1M MP3_R 500/200mA 100pF/50V/NP0 ESD7 FB616 GND R411 R406 R405 P4 5PIN/CKX-3.5-29 OPTI Vref2v5 0.1uF/25V/Y5V FB615 Vref2v5 R50 Vref2v5 100K 100pF/50V/NP0 4 5 3 2 1 4 5 3 2 1 E 9 MAIN BOARD (4/6) NC/LVSL10180Z020/18V/2pF A • See page 28 for IC Block Diagrams. 2 NC/LVSL10180Z020/18V/2pF 4-6. LED1 LED2 BT_LED1 BT_LED2 LED3 LED4 HT-CT180 4-7. SCHEMATIC DIAGRAM - MAIN Board (5/6) - 1 A 2 • See page 29 for IC Pin Function Description. 3 4 5 MAIN BOARD (5/6) D5 9 LL4148 + CE13 47uF/SMD NC/500/500mA BT_PIO7 R166 NC/33 TP41 +3.3VD R160 4.7K BT_PIO7 8 R159 STB_3V3 SYS_3V3 7 +3.3VD Q8 PNP_MMBT8550C FB33 6 47K AMP_MUTE AMP_MUTE D6 C235 C207 + 100uF/16V 0.1uF Q9 NPN_3DG3904M LL4148 47K B R126 Mute 10K R162 CE14 8 R161 4.7K 500/500mA 100pF/50V/NP0 FB32 AMP_VCC 8 6 AMP_DATA0 6,9 ALRCLK 6,9 ABCLK 33 R214 33 32 31 AMP_RST C125 1000pF/50V/X7R R167 33 30 AMP_LRCK R191 33 29 AMP_BCLK R198 33 28 AMP_MCLK R200 33 27 C76 AMP_DATA0 10PF/50V/NP0 C130 10PF/50V/NPO AMCLK 33 26 +3.3VD 25 R172 24 2.2 AMP_MUTE R173 0 +3.3VD 23 22 0 C145 C146 0.1uF/50V/X7R 4700pF/50V/X7R R177 0.1uF/50V/X7R C144 680pF/50V/X7R D R176 2.2K C143 21 20 19 SCL TEST_MODE SDA VSS INT_LINE VCC_REG RESET OUT2B SDI GND2 LRCKI VCC2 BICKI OUT2A XTI OUT1B GND_PLL VCC1 FILTER_PLL GND1 VDD_PLL OUT1A GND_REG PWRDN GND_DIG VDD VDD_DIG CONFIG TWARN / OUT4A OUT3B / FFX3B EAPD / OUT4BOUT3A / FFX3A C154 C153 0.22UF 0.22ȝF C118 2 3 L6 4 5 6 FR- 10uH 330pF/50V/X7R 6.2 R165 C122 0.1uF/50V/X7R C121 C123 C124 C155 3.3UF 0.1uF/50V/X7R C128 C127 0.1uF/50V/X7R R169 C126 R168 6.2 0.1uF/50V/X7R 22 8 L7 C129 XP10 C161 3.3UF FR+ 10uH L8 R171 C136 C132 330pF/50V/X7R 0.1uF/50V/X7R 12 13 R174 14 R175 0.1uF/50V/X7R 15 C141 0.1uF L9 16 22 6.2 C131 0.1uF/50V/X7R C140 C133 C134 0.47uF 0.01uF/50V/X7R 6.2 25W*2/30%/4/BTL FL+ 10uH AMP_18V 18 5-26V 3.3V: 70mA PVDD: 2.5A FR+ 2.4K =>1.8K 8 + R185 NC/33 R775 220K R779 220K R780 220K 1 CE17 NC/4.7uF/50V R178 NC/750 C530 10uF/16V/X7R Q756 PNP_3CG3906M FR+ Q757 PNP_3CG3906M R782 100 NC/BAT54C 2 R186 NC/3.9K/1% 10 => 56 1.2K=>3.9K C149 NC/0.1uF/25V/Y5V R182 NC/7.5K R187 NC/4.7K/1% + CE19 NC/100uF/16V/SMD R783 R188 NC/8.2K C150 0.1uF/25V/Y5V 100K C769 0.22UF/50V/Y5V AMP_FAULT Q24 NPN_3DG3904M Power Derating Circuit HT-CT180 3 3 4V => 2.7V 6mA F D7 R180 NC/1.8K 4 - SYS_5V NC/10uF/16V/SMD 220K + CE20 + R781 R776 220K E R184 NC/4.7K 4PIN/2.5mm C142 0.1uF/50V/X7R FL- 1/2power-control FL 17 STA339BW 2 4PIN/2.5mm 1 2 3 4 XP11 FL- 10uH 11 FL+ NC/F4558 U15A NC/1.8K 1 1 2 3 4 0.1uF/50V/X7R 9 10 FR 1 2 3 4 0.01uF/50V/X7R 0.47uF 7 FR- R179 1 2 3 4 C139 AMP_FAULT 34 33 R164 0.22ȝF AMP_SDA R163 1 C138 8 AMP_SCL AMP_SDA SA C137 C AMP_SCL GND_SUB GND_DIG C135 8 VDD_DIG 0.22ȝF 35 U14 GND 0.22ȝF 36 70/3A 0.22UF C120 0.1uF/50V/X7R C259 37 NC/4.7K 1uF/50V/X7R 4.7K FB17 + C260 R32 4.7K 70/3A 1uF/50V/X7R R31 4.7K 0.1uF/50V/X7R C147 R91 R29 FB16 470uF/35V +3.3VD CE15 +3.3VD 0.1uF/50V/X7R AMP_18V 24 24 HT-CT180 4-8. SCHEMATIC DIAGRAM - MAIN Board (6/6) - 1 A 2 3 4 5 6 7 MAIN BOARD (6/6) STB_3V3 C277 "18PF/5%" 3 STB_3V3 D21 R217 4.7K 1 2 1 2 BAT54S R139 NC/15PF D20 3 1 2 1000pF/50V/X7R NFC_INT NFC_INT C289 NFC R135 NPN_3DG3904M Q13 100K 47pF/50V/NP0 C281 "18PF/5%" C292 XP12 NC/100K NFC_INT R140 100K 100pF/50V/NP0 B R102 BT_NFC BT_NFC NC/10K C188 NC/0.1uF/25V/Y5V 1 2 TP60 R136 20K C286 BAT54S 2PIN/2.0mm R143 20K C458 Q10 NC/NPN_3DG3904M NFC Module (NFC-FS2) APPLICATION 4-9. PRINTED WIRING BOARD - KEY Board - • See page 18 for Circuit Boards Location. 1 • 2 4-10. SCHEMATIC DIAGRAM - KEY Board - 1 : Uses unleaded solder. 2 3 4 5 3 KEY BOARD (COMPONENT SIDE) A 6PIN/1.25mm XP4 1 2 3 4 5 6 1 2 3 4 5 6 POWER INPUT BT_Pairing VOL+ VOL- POWER R86 33 INPUT R102 33 BT_Pairing R116 33 VOL+ R85 33 VOL- R87 33 K2 POWER K3 INPUT 8 7 GND GND A KEY BOARD C92 100pF/50V/NP0 100pF/50V/NP0 100pF/50V/NP0 25 100pF/50V/NP0 25 C84 HT-CT180 C83 C 100pF/50V/NP0 KEY BOARD (CONDUCTOR SIDE) C34 B C21 B K4 PAIR K5 VOL+ K6 VOL- HT-CT180 4-11. SCHEMATIC DIAGRAM - BT NFC Board - 1 3 4 5 6 7 8 BT NFC BOARD R938 10K/1% R945 C793 R937 15K 2 4.7UF/10V/X5R 3 5.6nH NC/0 A R955 R954 BT_BT3V3 1000pF/50V/X7R BT_5V R944 20K R940 4.7UF/10V/X5R R941 A 15K 5 15K 6 4.7UF/10V/X5R + 7 - U604B F4558 C796 10uF R223 BT_L1 470 C282 1000pF/50V/X7R A A R942 MIC_BIAS GND PIO31_LED2 PIO18 PIO21 PIO6 PIO7 PIO8/UART_RTS PIO1/UART_TX PIO0/UART_RX PIO9/UART_CTS GND USB_DP USB_DN GND 3V3_OUT VDD 1V8_OUT 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 R614 R647 BT_NFC1 BT_PIO7_1 BT_PIO8_1 PIO8 BT_TX BT_RX 0 R1527 NC/0 R613 NC/10uF/10V/X7R BTVDD R1533 A +5V_D_A BT_FN1 1K 20K BT_BT3V3 BT1V8 BT_GND BT_5V 33 A BT_REFM 47K C798 0.1uF/25V/Y5V CE613 10uF/10V/Y5V R611 51K BT_GND A A 6 5 4 3 2 1 6 5 4 3 2 1 R957 R958 R959 R960 R961 BT_STATUS2 19 20 21 22 23 24 25 26 27 28 29 30 R15 10uF/10V/Y5V 0.1uF/25V/Y5V 100pF/50V/NP0 BT_GND C272 BT_GND BT_STATUS1 BT_GND 100pF/50V/NP0 C71 100pF/50V/NP0 0.1uF/25V/Y5V R111 1K C270 R17 1K 100pF/50V/NP0 C67 C271 BT_BT3V3 C70 BT_BT3V3 C268 BT_RST BT_RESET1 100pF/50V/NP0 XP3 6PIN/1.25mm BT_GND POWER1 INPUT1 BT_Pairing1 VOL+1 VOL-1 33 33 33 33 33 C269 BT_GND TP33 R79 100K C794 10uF/10V/X7R NC/1K SPI_MISO SPI_MISI SPI_CLK SPI_CSB GND BLUETOOTH FIRMWARE UPDATE C283 8 7 R12 C BT_R1 470 GND GND 1K R224 10K/1% C188 R7 GND AIO0 PIO14 PIO15 PIO16 PIO17 PIO10 SCL PIO11 PIO12 PIO13 SPI/PCM GND PIO3/PCM_OUT/MISO PIO2/PCM_IN/MISI PIO5/PCM_CLK/CLK PIO4/PCM_SYNC/CSB GND GND RESET GND PIO30/LED1 PIO29/LED0 VREGENABLE GND VBUS CHG_EXT VBAT_SENSE VBAT GND BTVDD A C795 A 10uF BT_REFM C73 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 10K/1% 10K/1% GND RF GND SPR_LP SPR_LN SPR_RP SPR_RN AGNG LINE_BP LINE_BN LINE_AP LINE_AN U10 4.7UF/10V/X5R C797 U604A F4558 4 BT_BM830 R943 20K 10K/1% R953 1 15K R952 60 59 58 57 56 55 54 53 52 51 50 49 NC/0.1uF/25V/Y5V B R950 10K/1% C69 NC/0.1uF/25V/Y5V BT_GND R951 R939 8 R956 C68 C791 10K/1% 8 R949 TP32 20K 4 10K/1% - R946 + Bluetooth D 9 A A 2 BT_GND BT_GND BT_GND BT_POWER_CONTROL1 4.7K E GND GND 24 23 A BT_GND 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 BT_R1 BT_L1 +5V_D_A BT_FN1 BT_STATUS1 BT_RESET1 BT_PIO7_1 BT_POWER_CONTROL1 BT_STATUS2 BT_BT3V3 BT_NFC1 POWER1 INPUT1 BT_Pairing1 VOL+1 VOL-1 C267 100pF/50V/NP0 100pF/50V/NP0 100pF/50V/NP0 100pF/50V/NP0 C266 100pF/50V/NP0 100pF/50V/NP0 100pF/50V/NP0 100pF/50V/NP0 C244 100pF/50V/NP0 C265 C243 100pF/50V/NP0 C263 C242 100pF/50V/NP0 C264 C241 26 100pF/50V/NP0 26 C240 HT-CT180 BT_GND C239 F C238 XP19 22PIN/0.5mm HT-CT180 4-12. PRINTED WIRING BOARD - BT NFC Board - 4-13. PRINTED WIRING BOARD - LED Board - • See page 18 for Circuit Boards Location. • See page 18 for Circuit Boards Location. 1 • : Uses unleaded solder. 2 3 1 BT NFC BOARD BT NFC BOARD (COMPONENT SIDE) (CONDUCTOR SIDE) 2 LED BOARD (COMPONENT SIDE) A A B LED BOARD (CONDUCTOR SIDE) B C 4-14. SCHEMATIC DIAGRAM - LED Board - 1 A 2 4 3 5 7 6 8 LED BOARD +5V +5V XP5 14 13 12 11 10 9 8 7 6 5 4 3 2 1 14 13 12 11 10 9 8 7 6 5 4 3 2 1 R71 180 +5V R154 180 LED2 LED_amber LED1 LED2 BT_LED1 BT_LED2 LED3 LED4 LED1 R41 Q10 4.7K C110 100pF/50V/NP0 C106 100pF/50V/NP0 C102 100pF/50V/NP0 C105 100pF/50V/NP0 2.2uF C104 100pF/50V/NP0 0.1UF C101 100pF/50V/NP0 C97 B R114 0.1UF Q12 4.7K C113 0.1UF NPN_3DG3904M C112 C94 LED2 NPN_3DG3904M 10PIN/0.5mm LED3 LED_amber ANALOG OPTICAL +5V +5V C R155 180 R56 180 LED5 LED_amber LED4 LED_amber +5V +5V R117 Q15 4.7K C114 0.1UF Q16 4.7K C115 0.1UF SURROUND 4 2 LED_4P_2PARTA LED6 NPN_3DG3904M BT_LED1 R142 4.7K 4.7K Q11 0.1UF NPN_3DG3904M C5 R143 CLEAR AUDIO+ BT_LED2 Q14 C107 0.1UF BLUETOOTH HT-CT180 R156 3 180 LED4 NPN_3DG3904M 1 R58 NPN_3DG3904M 180 D LED3 R144 27 27 • : Uses unleaded solder. 3 HT-CT180 • IC Block Diagrams – MAIN Board – U2, 3 EUP3482ADIR1 U11 AK5358A U21, 22 74LVC1G3157GV S 6 1 B1 A 4 3 B0 U4 AS1117 U531 TOP256EN 9 & &21752/& '5$,1' = & 9 9 U5 M12L64164A-7T (;7(51$/ &855(17 /,0,7; HT-CT180 Bank A Column Address Buffer & Refresh Counter 6+87'2:1 $8725(67$57 293 29 89 '& 0$; &855(17/,0,7 &203$5$725 +<67(5(7,& 7+(50$/ 6+87'2:1 6285&(6 &21752//(' 785121 *$7('5,9(5 6723 62)7 67$57 '& 0$; 26&,//$725 :,7+-,77(5 NN )5('8&7,21 ' 0$; &/2&. 6 5 4 /($',1* ('*( %/$1.,1* )5('8&7,21 . 36833(5 . 36/2:(5 L(U)DQM . 36/2:(5 ¹ )5(48(1&< ) 62)767$57 ,)% ,36833(5 ,36/2:(5 3:0 2)) Column Decoder 6285&(6 Data Control Circuit Latch Circuit Control Logic WE Command Decoder CAS 9 /,1( 6(16( 9 ,/,0,7 6723/2*,& 9 Sense Amplifier RAS . 36833(5 9 %* 9 7 92/7$*( 021,7 259 Input & Output Buffer Mode Register Row Address Buffer & Refresh Counter Row Decoder Address CS 212)) Bank D Bank C Bank B 62)767$57 ,17(51$/89 &203$5$725 &855(17 /,0,7 $'-867 CKE 9 ,)% Clock Generator 6+8175(*8/$725 (5525$03/,),(5 CLK ,17(51$/ 6833/< DQ 28 28 HT-CT180 • IC Pin Function Description MAIN BOARD U6 MT8301_OQE (SYSTEM CONTROLLER) Pin No. 1 2 3 4 5 6 7 8, 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 to 50 51 52, 53 54 55 to 60 61 62 63 to 66 67 68 to 70 71 72 73 74 75, 76 Pin Name AVDD12_2 AVDD33_1 XTALI XTALO V14 GPO5 AVDD33_2 NC GPIO2 USB_DP USB_DM VDD33_USB PAD_VRT VDD12_USB DV_Y2 DV_Y3 DV_Y4 SF_CS SF_DO SF_DI DVDD33 SF_CK UP1_6/SCL UP1_7/SDA GPIO11 GPIO6 PRST_ IR_ GPIO3/INT_ GPIO4 DV_C0 DV_C1 DV_C2 DV_C3 SD_MS_D2 SD_MS_D3 GPIO13 GPIO9 GPIO8 GPIO7/CKE_ DVDD33 RD0 to RD7 DQM0 RD15, RD14 DVDD12 RD13 to RD8 DQM1 RCLK RA11, RA9 to RA7 DVDD33 RA6 to RA4 RWE_ CAS_ RAS_ DVDD33 BA0, BA1 I/O I O I O I I/O I/O I I I I O O I O O O I O I I I I I O I O I O I O O I/O I/O O I/O I/O O O O O O O O O Description Power supply terminal (+1.2V) Power supply terminal (+3.3V) System clock input terminal (27 MHz) System clock output terminal (27 MHz) Reference voltage (+1.4V) input terminal LED drive signal output terminal (for analog indicator) Power supply terminal (+3.3V) Not used Power control signal input terminal Two-way USB data (+) bus terminal Not used Two-way USB data (–) bus terminal Not used Power supply terminal (+3.3V) USB generating reference current input terminal Power supply terminal (+1.2V) Volume (–) key input terminal SPDIF signal input terminal (for optical) Volume (+) key input terminal Chip select signal output terminal (for serial flash) Data output terminal (for serial flash) Data input terminal (for serial flash) Power supply terminal (+3.3V) Clock signal output terminal (for serial flash) LED drive signal output terminal (for Bluetooth indicator) LED drive signal output terminal (for Bluetooth indicator) Serial data input terminal (for DSP) Serial data output terminal (for DSP) Reset signal input terminal “L”: reset IR control signal input terminal Interrupt request signal input terminal (for NFC) Input key input terminal Power key input terminal Reset signal output terminal (for Bluetooth) Status signal input terminal (for Bluetooth) Power control signal output terminal (for Bluetooth) Audio enable signal input terminal (for Bluetooth) Reset signal output terminal (for AMP) Status signal input terminal (for Bluetooth) FN signal output terminal (for Bluetooth) Audio selection signal output terminal Not used Power supply terminal (+3.3V) Two-way data bus terminal (for SDRAM) Data mask signal output terminal (for SDRAM) Two-way data bus terminal (for SDRAM) Power supply terminal (+1.2V) Two-way data bus terminal (for SDRAM) Data mask signal output terminal (for SDRAM) Clock signal output terminal (for SDRAM) Address signal output terminal (for SDRAM) Power supply terminal (+3.3V) Address signal output terminal (for SDRAM) Write enable signal output terminal (for SDRAM) Column address strobe signal output terminal (for SDRAM) Row address strobe signal output terminal (for SDRAM) Power supply terminal (+3.3V) Bank address signal output terminal (for SDRAM) 29 HT-CT180 Pin No. 77 to 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107, 108 109, 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125, 126 127 128 129 30 Pin Name RA10, RA0 to RA3 DVDD12 SPDIF/GPIO12 GPIO10/HPLG EXT_RES AVDD33_12 TXCN TXCP AVDD12_C TX0N TX0P AVSS12 TX1N TX1P AVDD12_D TX2N TX2P GPIO29 GPIO30 GPIO31 GPIO32 GPIO33 AVDD33 VREF/GPIO14 FS NC AVDD33, AGND12 NC AKIN2/GPIO19 ADVCM/GPIO20 AKIN1/GPIO21 AADVDD APLLVDD_GPIO/ GPIO34 APLLCAP/GPIO35 ADACVSS LFE/GPIO ABCK AR/GPIO0 AVCM AL/GPIO ALRCK ASDATA0 ADACVDD1, ADACVDD2 AVDD12 NC E-PAD/GND I/O O O I I O O O O O O O O O O O I I/O O I I O O - Description Address signal output terminal (for SDRAM) Power supply terminal (+1.2V) Power on/off control signal output terminal Bluetooth pairing key input terminal External resistor connection terminal Power supply terminal (+3.3V) TMDS clock (negative) signal output terminal Not used TMDS clock (positive) signal output terminal Not used Power supply terminal (+1.2V) TMDS data (negative) output terminal Not used TMDS data (positive) output terminal Not used Ground terminal TMDS data (negative) output terminal Not used TMDS data (positive) output terminal Not used Power supply terminal (+1.2V) TMDS data (negative) output terminal Not used TMDS data (positive) output terminal Not used LED drive signal output terminal (for surround indicator) Serial data output terminal (for AMP) Clock signal output terminal (for AMP) Fault signal input terminal (for AMP) Not used Power supply terminal (+3.3V) Muting signal output terminal (for AMP) Full scale adjustment terminal Not used Power supply terminal (+3.3V) Not used Audio data input terminal LED drive signal output terminal (for clear audio+ indicator) LED drive signal output terminal (for optical indicator) Power supply terminal (+3.3V) O Clock signal output terminal (for subwoofer) O O I O I I I O Serial data output terminal (for subwoofer) Ground terminal Master clock signal output terminal Bit clock signal input terminal (for DAC) Audio data (subwoofer) output terminal (for AMP) Reference voltage input terminal (for DAC) I2C busy signal input terminal (for subwoofer) L/R sampling clock signal input terminal (for DAC) Audio data (L-ch/R-ch) output terminal (for AMP) - Power supply terminal (+3.3V) - Power supply terminal (+1.2V) Not used Ground terminal HT-CT180 MAIN BOARD U14 STA339BW (DIGITAL AMP) Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 Pin Name GND_SUB SA TEST_MODE VSS VCC_REG OUT2B GND2 VCC2 OUT2A OUT1B VCC1 GND1 OUT1A GND_REG VDD CONFIG OUT3B/FFX3B OUT3A/FFX3A EPAD/OUT4B TWARN/OUT4A VDD_DIG GND_DIG PWRDN VDD_PLL FILTER_PLL GND_PLL XTI BICKI LRCKI SDI RESET INT_LINE SDA SCL GND_DIG VDD_DIG GND I/O I I I/O I/O O O O O I I O O O I/O I I I I I I I O I I - Description Ground terminal I2C select address signal input terminal Fixed at “L” in this unit Fixed at “L” in this unit Internal reference voltage (–3.3V) input/output terminal Internal reference voltage input/output terminal Audio signal (R-ch) output terminal Ground terminal Power supply terminal Audio signal (R-ch) output terminal Audio signal (L-ch) output terminal Power supply terminal Ground terminal Audio signal (L-ch) output terminal Internal reference ground terminal Internal reference voltage (+3.3V) input terminal Parallel mode command signal input terminal Fixed at “L” in this unit Not used Not used Not used Not used Power supply terminal (+3.3V) Ground terminal Muting signal input terminal Power supply terminal (+3.3V) (for PLL) Connection to PLL filter terminal Ground terminal (for PLL) Master clock signal input terminal Bit clock signal input terminal L/R sampling clock signal input terminal Audio data (L-ch/R-ch) input terminal Reset signal input terminal Fault signal output terminal Serial data input terminal Clock signal input terminal Ground terminal Power supply terminal (+3.3V) Ground terminal 31 HT-CT180 SECTION 5 EXPLODED VIEWS Note: • -XX and -X mean standardized parts, so they may have some difference from the original one. • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. 5-1. • The mechanical parts with no reference number in the exploded views are not supplied. • Color Indication of Appearance Parts Example: KNOB, BALANCE (WHITE) . . . (RED) Parts Color Cabinet’s Color The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. REAR CABINET SECTION AC1 7 5 7 7 8 7 7 7 6 7 7 7 7 6 7 7 not supplied front cabinet section 6 not supplied 3 4 4 Ref. No. Part No. Description 1 2 3 4 5 4-564-845-01 9-885-199-20 4-566-000-01 4-565-998-01 X-2591-065-1 KEY (@/1, INPUT, PAIRING, − VOL, + VOL) KEY BOARD, COMPLETE (Including Cushion) SCREW (2.6X6 S) SCREW (3X8 S) REAR CABINET ASSY 6 4-564-837-01 FOOT CUSHION 32 Remark Ref. No. 7 3 2 1 Part No. Description 7 08 0 AC1 0 AC1 4-565-999-01 4-472-176-01 9-885-199-69 9-885-199-70 SCREW (3X10 B) CORD BUSH AC CORD U (US, CND) AC CORD EURO (AEP) 0 AC1 0 AC1 9-885-199-71 9-885-199-73 AC CORD 13A (UK) AC CORD AU (AUS) Remark HT-CT180 5-2. FRONT CABINET SECTION 56 D 57 56 A 57 58 (CUSHION (A)) (CUSHION (B)) 57 56 (CUSHION (EVA)) E F 57 57 C 56 57 (CUSHION (C)) B not supplied ANT1 54 53 SP3 54 54 A 53 55 54 (SHEET (IC)) 56 (CUSHION (C)) FFC1 54 not supplied 54 E 54 54 52 59 56 NFC module not supplied SP1 54 D 54 54 F B C not supplied FFC2 SP2 54 51 53 54 53 SP4 BT NFC board 60 52 Note 1: When replacing the BT NFC board or the NFC module, be sure to replace both at the same time. The BT NFC board or the NFC module cannot replace with single. Note 2: Ref. No. 56 is a part that bundles the cushions necessary when replacing the MAIN board. Select cushions that are the same as the cushions installed on the MAIN board before replacement, and then affix them to the MAIN board. CUSHION (EVA) : 1 piece, size 350 mm x 8 mm SHEET (IC) : 1 piece, size 10 mm x 10 mm CUSHION (A) : 1 piece, size 126 mm x 13 mm CUSHION (B) : 1 piece, size 183 mm x 15 mm CUSHION (C) : 2 pieces, size 32 mm x 10 mm Note 3: When WIRELESS board is replaced, refer to “NOTE OF REPLACING THE WIRELESS BOARD” on page 5. Ref. No. Ref. No. Part No. Description Remark 51 52 53 54 55 X-2591-064-1 4-564-837-01 4-565-989-01 4-565-998-01 9-885-199-12 FRONT CABINET ASSY FOOT CUSHION SCREW (2.6X8 S) SCREW (3X8 S) LED BOARD, COMPLETE 56 A-2070-034-A 57 58 4-565-990-01 9-885-199-14 59 59 9-885-199-10 9-885-201-21 SERVICE (FOR MAIN PWB) (Cushions, 1 set) (See Note 2) SCREW (3X6 B) WIRELESS BOARD, COMPLETE (Including Cushion) (See Note 3) MAIN BOARD, COMPLETE (US, CND) MAIN BOARD, COMPLETE (AEP, UK, AUS) Part No. Description Remark 60 9-885-199-13 ANT1 FFC1 FFC2 SP1 9-885-199-11 9-885-199-22 9-885-199-21 9-885-199-93 BT NFC BOARD, COMPLETE (Including NFC module, Cushion, Double sided tape) (See Note 1) ANTENNA (Including Wire, Double sided tape) FFC 10P/0.5/M-LED (Including Cushion) FFC 22P/0.5/M-BT (Including Cushion) LOUDSPEAKER (4.3X12 cm) (Including Cushion) (Woofer: L-ch) SP2 9-885-199-93 SP3 SP4 9-885-199-65 9-885-199-65 LOUDSPEAKER (4.3X12 cm) (Including Cushion) (Woofer: R-ch) LOUDSPEAKER (1.4X2.5 cm) (Tweeter: L-ch) LOUDSPEAKER (1.4X2.5 cm) (Tweeter: R-ch) 33 HT-CT180 SECTION 6 ACCESSORIES Ref. No. Part No. Description 4-559-026-11 MANUAL, INSTRUCTION (ENGLISH, FRENCH, SPANISH) (US, CND) MANUAL, INSTRUCTION (ENGLISH) (UK, AUS) MANUAL, INSTRUCTION (FRENCH, SPANISH, DUTCH) (AEP) MANUAL, INSTRUCTION (GERMAN, POLISH, ITALIAN) (AEP) MANUAL, INSTRUCTION (SWEDISH) (AEP) 4-559-026-21 4-559-026-31 4-559-026-41 4-569-356-11 4-569-356-21 Remark 4-569-356-61 MANUAL, INSTRUCTION (DANISH, FINNISH) (AEP) MANUAL, INSTRUCTION (PORTUGUESE) (AEP) MANUAL, INSTRUCTION (GREEK) (AEP) MANUAL, INSTRUCTION (CZECH, HUNGARIAN) (AEP) MANUAL, INSTRUCTION (TURKISH) (AEP) 4-569-356-71 4-569-356-81 4-569-356-91 MANUAL, INSTRUCTION (SLOVAK) (AEP) MANUAL, INSTRUCTION (ESTONIAN) (AEP) MANUAL, INSTRUCTION (ROMANIAN) (AEP) 501 1-492-930-11 502 503 1-783-327-61 4-564-836-01 REMOTE COMMANDER (RMT-AH100U) (Remote control) CABLE, LIGHT PLUG (Optical digital cable) FOOT SET (Speaker pads for the subwoofer) (4 pieces, 1 set) 4-569-356-31 4-569-356-41 4-569-356-51 501 Remote control (1) 503 Speaker pads for the subwoofer (4) 34 502 Optical digital cable (1) HT-CT180 MEMO 35 HT-CT180 REVISION HISTORY Ver. Date 1.0 2015.02 Description of Revision New