Download SERVICE MANUAL WINNER 2004

SERVICE MANUAL
WINNER 2004
© 2011 Handicare
All rights reserved.
The information provided herein may not be reproduced and/or published in any form, by print, photo print, microfilm or any other means
whatsoever (electronically or mechanically) without the prior written authorization of Handicare.
The information provided is based on general data concerning the constructions known at the time of the publication of this manual. Handicare
executes a policy of continuous improvement and reserves the right to changes and modifications.
The information provided is valid for the product in its standard version. Handicare cannot be held liable for possible damage resulting from
specifications of the product deviating from the standard configuration.
The available information has been prepared with all possible diligence, but Handicare cannot be held liable for possible errors in the
information or the consequences thereof.
Handicare accepts no liability for loss resulting from work executed by third parties.
Names, trade names, etc. used by Handicare may not, as per the legislation concerning the protection of trade names, be considered as being
available.
XXXXXX-000001000-en.doc
2
Version 2013v1
Table of contents
This manual ................................................................................................................................................................. 4
Product reference ....................................................................................................................................................... 5
Available documentation ........................................................................................................................................... 7
Service and technical support................................................................................................................................... 7
Identification plate ...................................................................................................................................................... 7
Identification of the product ...................................................................................................................................... 7
Warranty stipulations concerning the scooter ........................................................................................................ 8
Liability stipulations concerning the Product ......................................................................................................... 9
Used scooters and the environment ........................................................................................................................ 9
1
Use according to purpose ........................................................................................................................................ 9
1 General safety regulations and instructions .................................................................................................. 10
1.1 Decals and instructions on the scooter ........................................................................................................ 10
1.2 Technical specifications ............................................................................................................................... 10
1.3 Modifications................................................................................................................................................. 10
1.4 Safety ........................................................................................................................................................... 10
2 Adjustment options ........................................................................................................................................... 12
2.1 Seat adjustments .......................................................................................................................................... 12
2.1.1
Adjusting the seat height and depth............................................................................................... 12
2.1.2
Backrest adjustment ...................................................................................................................... 12
2.1.3
Lower-backrest adjustment ............................................................................................................ 12
2.1.4
Adjusting the arm-rest .................................................................................................................... 13
2.1.5
Adjusting the headrest (option) ...................................................................................................... 13
2.2 Adjusting the steering column ...................................................................................................................... 13
3 Drive programs .................................................................................................................................................. 14
3.1 Controller settings Winner Solo .................................................................................................................... 14
3.2 Controller settings Winner S-drive 120A ...................................................................................................... 15
3.3 Controller settings Winner S-drive 140A Schmid. ........................................................................................ 16
3.4 Controller settings Winner S-drive 140A Schmid Alpine. ............................................................................. 17
3.5 Controller settings Winner S-drive 140A CT. ............................................................................................... 18
3.6 Electrical Diagram S-Drive ........................................................................................................................... 20
3.7 Connections printed circuit board ................................................................................................................. 21
4 Technical specifications ................................................................................................................................... 22
4.1 Product specifications .................................................................................................................................. 22
4.1.1
Winner ............................................................................................................................................ 22
4.2 Approval ....................................................................................................................................................... 24
4.3 Service information transaxles. .................................................................................................................... 24
5 Use of the parts lists ......................................................................................................................................... 25
Version 2013v1
3
Preface
This manual
This manual contains the basic instructions for repairs and general maintenance of the Winner electric scooter.
Mechanics who do repairs on this scooter must be well trained and familiar with the repair methods and the
maintenance of the Winner electric scooter.
It is important to see to it that work is always done safely, particularly with respect to activities where the scooter
must be lifted up.
We advise that you contact our service department before doing repair work on a scooter that has been involved in
an accident.
The following specifications are important when ordering parts:
-
Model
Manufacture year
Color
Identification number
Part number
Name of the relevant part
This information can be found on the identification plate. See 'Identification of the product'.
4
Version 2013v1
Preface
Product reference
XXXXXX-010004000-en.doc
B
A
G
E
D
C
F
010004000
The product has the following decals and labels.
A. Charging connection
B. Fuse for lighting
C. Automatic fuse
D. Driving
E. Pushing
F. Tire pressure wheels
G. Reverse – Forward drive
Version 2013v1
5
Preface
A.
Charging connection
For charging the batteries, see 'charging'.
PICPRO-010004210-en.doc
B.
Fuse for the lighting
Here you find the fuse for the lighting. See 'Product specifications'.
C.
Automatic fuse
The scooter has a safety fuse feature. See 'automatic fuse' and 'faults'.
PICPRO-010004270-en.doc
D.
Driving
The drive of the motor is switched on: the scooter can be electrically driven.
E.
Pushing
The drive of the motor is disconnected: the scooter can be pushed electrically.
MAX.
2,7
BAR
F.
Tire pressure wheels
For tire pressure of the wheels, see 'product specification sheet'.
G.
Reverse – Forward drive
When the operating handle is pressed, the scooter will drive forward or in reverse. See ‘Driving
forward and in reverse’.
The following pictograms are used in this manual:
XXXXXX-010004020-en.doc
CAUTION
Procedures that can result - if they are not executed properly - in damage to the product, the
environment, or human injury.
PICDOC-010004110-en.doc
ATTENTION!
Suggestions and advice for conducting the relevant tasks or activities more easily.
PICDOC-010004120-en.doc
Consult the specified information source(s) first.
PICDOC-010004130-en.doc
Pull the charge cord out of the charging connection of the scooter before doing any
maintenance on the scooter.
PICDOC-010004140-en.doc
6
Version 2013v1
Preface
Available documentation
The following technical documentation is available / required to service this scooter:
- Owner's manual
- Service manual.
XXXXXX-010005000-en.doc
Service and technical support
For information concerning specific settings, maintenance or repair work please contacts your dealer. He is always
prepared to help you.
Ensure you have at hand:
Model
Manufacture year
Identification number
This information can be found on the identification plate. See 'Identification of the product'.
XXXXXX-010006000-nl.doc
Identification plate
•
See fig. 000000010.
On this plate (A) information on the product can be found. See: 'Identification
of the product'.
A
000000010
Identification of the product
•
See fig. 010007010.
•
For the place of the identification plate, see 'main components'.
XXXXXX-010007010-en.doc
¤
Model
Manufacture year
Identification number
User area indoors or outdoors
Maximum load in kg
LAGE DIJK 10
5705 BZ HELMOND
THE NETHERLANDS
A.
B.
C.
D.
E.
A
B
C
YEAR/JAAR/JAHR:
D
E
Version 2013v1
CAT
2000
IDNR.: CT 00004
USAGE:
INDOOR/OUTDOOR
GEBRUIKSGEBIED: BINNEN/BUITEN
GEBRAUCHSBEBIET: INNERHALB/AUSSERHALB
MAX.LOAD/MAX.BELASTB./ZUL.GESAMTGEW.: 100 KG
TYPE/TYPE/TYP:
010007010
7
Preface
Warranty stipulations concerning the scooter
In the following warranty and liability stipulations the terms and definitions as summed up hereafter must be
explained as follows:
•
Product:
•
•
•
Customer:
Dealer:
User:
The hand-operated or electrical wheelchair or scooter manufactured and delivered by
Handicare.
The person who directly obtains a Product from Handicare or an authorized representative.
The person who delivers a Product obtained from Handicare to customers or third parties.
The person who uses a Product manufactured by Handicare.
Irrespective of what is determined concerning warranty conditions applicable to the Product, in any case the
following applies with regard to the warranty:
1.
Except insofar as described otherwise Handicare guarantees the Product for its suitability for the purpose for
which the Product is intended - all of these points as described in this manual - and for the quality of the
material of which the Product is made and the manner in which the Product is manufactured.
2.
Repairs or replacement of parts of the Product that may be necessary as a result of faults that are based on
qualitatively faulty material or manufacturing errors will be executed free of charge, as long as such faults
occurred within one (1) year after the date of delivery of the Product to the Customer. The parts to be
replaced must be shipped post-paid to Handicare. Disassembly or assembly of these parts is for the
expense of the Customer. Therefore the following cases are not eligible for free repair or replacement as
meant above:
- The repair or replacement that is necessary in connection with faults that arise after one (1) year after
the date of delivery of the Product to the Customer;
- The repair or replacement that is required in connection with faults due to improper or careless use of
the Product or that are based on the Product being used for another purpose than the one for which it is
intended, in which regard it applies that if the Customer is a Dealer, this Dealer will indemnify Handicare
against possible claims from Users or other third parties for faults based on an incorrect or careless use
of the Product;
- Parts that are subject to wear, and the need for repair or replacement of the parts are the actual
consequence of normal wear. These can include, but are not limited to, tires, shrouds, arm-pads,
seatings etc.
3.
Irrespective of that stipulated under 2, it applies as far as an electric Product is concerned that with regard to
the battery that forms part of the Product warranty is only given in case of faults or non-functioning of the
battery that are demonstrably the direct consequence of material or manufacturing errors. A fault or nonfunctioning of the battery as a result of normal wear is not covered by the warranty as meant in these
warranty stipulations. Similarly not covered by the warranty are faults or non-functioning that are the
consequence of improper or unprofessional use of the Product or the battery that is part of the Product,
including the incorrect charging of the battery and the failure to carry out timely and good maintenance, in
which context it also applies that if the Customer is a Dealer, this Dealer will indemnify Handicare against
possible claims from Users or other third parties that are based on the above mentioned improper or
unprofessional use of the Product or the battery that is part of the Product. Handicare does not guarantee
batteries provided by dealers or purchased by the customer.
4.
The warranty conditions as mentioned in above stipulations in any case become null and void if:
- The guidelines of Handicare for the maintenance of the Product are not, or insufficiently, followed;
- A necessary repair or replacement of parts is based on neglect, damage or abuse of the Product or a
use of the Product for another purpose than the one for which it was intended;
- Parts of the Product are replaced by parts of another origin than those which Handicare uses and/or
parts of the Product are replaced without the permission of Handicare.
5.
The warranties as mentioned in stipulations 1 through 3 also become null and void if what is involved is reused by a new user within the warranty period and that such re-use necessitates adaptations to the product
and those adaptations are carried out without the instructions and/or at the order of Handicare.
6.
To retain rights under the above delineated warranties the Customer must, in case of damage or other
calamities, as rapidly as possible contact Handicare and inform them as fully as possible. The possibility of
taking recourse to the above-mentioned warranty conditions becomes null and void for the Customer in any
case after 20 workdays after the claim situation or the calamity arises that was the reason for the recourse to
the guarantee.
7.
The replacement of a part or the repair or the reconditioning of the Product within a current warranty period
does not extend the warranty period.
8.
Handicare gives no warranty on repair to or reconditioning of the Product carried out other than under order
of and/or at the instructions of Handicare. If repairs and/or reconditioning are executed by or on behalf of a
Customer, the Customer indemnifies Handicare with respect to the claims of third parties who result, in the
broadest sense of the word, from such repairs or reconditioning.
EBAXXX-010008010-en.doc
8
Version 2013v1
Preface
Liability stipulations concerning the Product
Irrespective of what is determined regarding liability in the general conditions applicable to the Product, with regard
to liability in any case the following applies:
1.
taking into consideration the following stipulations, Handicare only accepts liability for loss due to death or
physical injury that is the result of a defect in the Product for which Handicare is responsible and for damage
to another object that is the private property of the user of the Product, as long as said loss is the direct
result of a fault in the Product.
2.
Handicare accepts no other or further liability than delineated under 1. In particular Handicare accepts no
liability for consequential damage, in any form whatsoever.
XXXXXX-010008020-en.doc
Used scooters and the environment
If your scooter has become superfluous or needs to be replaced, it can usually be taken back by
your dealer. If this is not possible, please contact your local authorities for the possibilities of
recycling or an environmentally friendly way of disposing of the used materials.
For the production of the scooter several plastics and metals have been used. The scooter also
contains electronic components that must go to electronic waste. Used batteries belong to
chemical waste.
1
Use according to purpose
The scooter Winner was designed for:
transport of persons with a weight of up to 159 kg
use on paved roads, sidewalks, footways, and bike-ways.
use in and around the house
•
•
•
Your supplier should give you good user's instructions before you can independently operate the product and
participate in traffic.
You must be able to correct the consequences of actions while driving the Winner.
Consider operating the Winner scooter under the monitoring of an experienced dealer during first operations.
The Winner scooter is not a motorized vehicle in the traffic regulations sense.
The Winner has a maximum speed of approximately 12 or 15 km/h (7 or 10 mph), depending on the model.
PLEASE MAKE SURE YOU ARE WELL ACQUAINTED WITH THE CONTENTS OF THIS OWNER’S MANUAL
BEFORE DRIVING THE WINNER.
If you use the scooter for other purposes than those for which it is intended, Handicare accepts no liability
whatsoever for damage or injury resulting from such use other than that for which the scooter was developed and
designed.
'Use according to purpose' as established in EN 292-1 is the use for which the technical product is suitable according to the statement of the manufacturer, including his
instructions in the sales brochure. In case of doubt this is the use that follows from the construction, execution and function of the product. Use according to purpose also
includes taking into consideration the instructions in the owner's manual.
Version 2013v1
9
General safety guidelines and instructions
1 General safety regulations and instructions
Handicare accepts no liability whatsoever for damage or injury caused by the failure to (strictly) adhere to the safety
guidelines and instructions or else due to carelessness during the use and cleaning of the scooter and possible
accessories. Depending on the specific work circumstances or the accessories used, additional safety instructions
may be required. Please contact your dealer immediately if you observe a potential danger during the use of the
product.
The user of the scooter (see under 'use according to purpose') is at all times fully responsible for
the fulfillment of the locally applicable safety regulations and guidelines.
1.1
Decals and instructions on the scooter
Signs, symbols and instructions placed on this scooter comprise part of its safety facilities. They must never be
covered or removed and must remain present and clearly legible throughout the entire life span of the scooter.
Immediately replace or repair illegible or damaged signs, symbols and instructions. Contact your dealer with regard
to this.
1.2
Technical specifications
The technical specifications may not be changed.
1.3
Modifications
Modification of (parts of) this product is not permitted.
1.4
Safety
To avoid accidents and undesirable situations, it is of great importance to pay attention to the following safety
instructions.
• Pay extra attention to riding on slopes:
- Never drive the Winner up a slope with an angle greater than 11°.
- On slopes always drive slowly and with awareness.
- Never drive down a slope at full speed.
- Do not drive down slopes with loose gravel or a sandy surface, because one of the back
wheels might slip.
- Do not turn on a slope.
• Never take curves at full speed. Decrease speed on the approach and on the curve.
• Be sure that no items of clothing hang loose. These could become caught between the wheels.
• Make sure your fingers do not get caught in the mechanism of the steering adjustment.
• Adjust your driving according to the circumstances:
- Drive carefully on slippery roads, resulting from rain, ice, or snow!
- Drive more slowly in crowded environments.
- Do not use the scooter on uneven roads.
- Avoid the Winner from coming into contact with seawater. Seawater is caustic and may
damage the scooter.
- Avoid the Winner from coming into contact with sand. Sand can affect the moving parts of the
scooter, resulting in unnecessarily rapid wear.
• Never operate the scooter when you are under the influence of drugs, alcohol or medication that
could affect your driving ability.
• You must have sufficient visual acuity to be able to drive safely in the scooter.
• You are obliged to put the lights on when the view is hindered.
• Only use the indicator lights to indicate an intended change in driving direction.
• Only use the horn when it is necessary to warn pedestrians of other road users of dangerous
circumstances.
• Never place metal parts on top of the batteries: this may cause a short in the batteries, resulting
in damage.
• Do not take along any passengers: your scooter was specifically designed to transport only
yourself.
• Do not burden your scooter with any more load than can be placed in the basket.
• Never hang anything from the handlebars.
10
Version 2013v1
General safety guidelines and instructions
• Never use your scooter to pull a cart: the scooter was not designed for this. Anyway, it is
prohibited to do so. You might seriously damage your scooter if you do.
• Do not use the footplate as a step.
• Do not place your feet close to the front wheel and the front fork. Always keep your feet on the
rubber mat, rather than against the front cover.
• The scooter is electronically operated. Certain parameters have been factory-set. These settings
guarantee a comfortable and efficient use. It is not permitted to change these parameters.
• The standard version of your scooter was tested according to the strictest EMC requirements.
Mobile telephones have no influence on the driving behaviour of the scooter.
When using a mobile telephone in the vicinity of a scooter with special adaptations, you are
advised to first switch off the scooter.
• Your scooter may influence electromagnetic fields such as alarm systems.
• If the electronics of the scooter is not properly screened off, this may affect sensitive electrical
appliances, such as shop alarms and garage openers. The scooter has been tested for this.
Should any problems of this nature occur, please report these to your supplier immediately.
• Take care in ultra-violet light: this may cause premature deterioration of materials such as rubber,
plastic, and enamel.
• Watch out for protruding parts: these may damage your scooter or the environment.
• Keep your scooter away from open flames.
Version 2013v1
11
Adjustment options
2 Adjustment options
XXXXXX-010500000-en.doc
2.1
Seat adjustments
The Winner seat offers a number of adjustment options to increase the sitting and driving comfort.
The following may be adjusted:
A. Seat height and depth
B. Backrest
C. Lower-back rest
D. Arm-rests
E. Headrest
F. Steering column
2.1.1 Adjusting the seat height and depth
The whole seat may be adjusted as follows:
•
10 cm in height
•
10 cm in forward direction
Both adjustments should be made by the dealer.
2.1.2 Backrest adjustment
•
See fig. 000000140.
The backrest is continuously adjustable, from a fully horizontal to a fully
vertical position.
The adjustment must be done as follows:
•
Pull up the handle (A) while you are on the seat.
The backrest will now automatically move forward.
•
Press the backrest backward by leaning back to a position that is most
comfortable for you.
•
After adjustment, push the handle down to secure the backrest in the
position you have chosen.
A
000000140
Attention:
Do not operate the handle if the seat is unoccupied, because the backrest will come forward
very powerfully.
The backrest must be adjusted in such a way that your back is properly supported while driving.
If the backrest is tilted too far backwards, this will negatively influence the seating stability,
especially on slopes.
2.1.3 Lower-backrest adjustment
•
See fig. 000000150.
A
The lower-backrest can be adjusted to various positions, varying from more or
less support in the lower-back area.
The adjustment must be done as follows:
•
Seat yourself on the seat.
•
Turn knob (A) in such a way that the lower-backrest reaches the most
optimal position for you.
000000150
12
Version 2013v1
Adjustment options
2.1.4 Adjusting the arm-rest
•
See fig. 000000160.
Both armrests can be folded up completely. The height and the angle of the
armrest can be adjusted.
A
The adjustment must be done as follows:
•
Turn wheel (A) to adjust the height and the angle of the arm-rest.
Attention: if the position of the backrest is adjusted, the
position of the
Armrests will change along with it.
000000160
2.1.5 Adjusting the headrest (option)
The headrest can be adjusted as follows:
•
Three height adjustments
•
Tilting forward and back
Adjusting the height of the headrest
The headrest can be pulled up by hand, and will lock into one of three positions by means of a click.
Tilting the headrest:
The headrest can be tilted by hand until the desired position is reached.
2.2
•
Adjusting the steering column
See fig. 000000130.
The steering column can be adjusted as follows:
•
Pull up handle (A) with one hand, while at the same time pulling the
steering column towards you with the other, until the most comfortable
position is reached.
•
Release the handle in the chosen position. Then, release the steering
column.
If you release the steering column while still holding up the handle, the gasspring-loaded steering column will move to its most forward position.
Use caution when adjusting the steering column, to avoid
getting your fingers jammed.
Version 2013v1
A
000000130
13
Drive programs
3 Drive programs
A hand held programmer is deliverable for programming the Winner with Solo controller. An user maunal belongs
to the delivery of this manual. For the Winner with S-Drive controller there is a software program available but it’s
also programmable with the hand held programmer.
The standard adjustments are stated in the table below.
3.1
Controller settings Winner Solo
Function
Forward Acceleration
Forward Deceleration
Reverse Acceleration
Reverse Deceleration
Forward speed
Reverse Speed
Invert Throttle Polarity
Power Down Timer
Help Mode
Diagnostics
Current Limit
Motor Compensation
Hold Factor
Mid Current
Brake Time
ISO Test
Inhibit Polarity
Bridge Hold Time
Throttle Gain
Pulse Reverse Alarm
Wig-wag Throttle
Low Battery Flash Inhibit
Throttle Deadband
Output Voltage
TruCharge Cable Resistance
TruCharge Cal.
Profile values
Scale I factor
Scale V factor
Options register
I limit reduction
Abs I factor
Demand clipping
Solo mode
14
Range
0.1 to 10s, Fast/Slow
0.1 to 10s, Fast/Slow
0.1 to 10s, Fast/Slow
0.1 to 10s, Fast/Slow
0 to 100%, Fast/Slow
0 to 100%, Fast/Slow
Yes/No
0 to 20 minutes
On-line help text
Fault codes from Solo
20A to max rating
0 to 1W
100 to 420%
0 to 100%, 1 to 255s
0 to 1s
On / Off
Hi / Lo
0 to 5s
0 to 1250%
Yes / No
Yes / No
Yes / No
3% to 100%
20 to 40V
10 to 250 mOhm
1 to 200
-
Resolution
100 ms
100 ms
100 ms
100 ms
1%
1%
1 min
*
*
1A
5 mW
4%
1%, 1s
10 ms
20 ms
5%
1%
1V
5 mOhm
High
Low
30
30
12
12
35
35
35
35
100
100
40
40
Yes
0
Not programmable
Not programmable
110
45
152
15
50
80
On
Lo
60
150
Yes
Yes
No
15
24
40
100
40
80
75
157
30
43
160
30
1
Version 2013v1
Drive programs
3.2
Controller settings Winner S-drive 120A
Winner S-Drive 120 15kmh
Speed Settings
Forward Acceleration (0,1 Seconds)
Forward Deceleration (0,1 Seconds)
Reverse Acceleration (0,1 Seconds)
Reverse Deceleration (0,1 Seconds)
Max Forward Speed (%)
Min Forward Speed (%)
Max Reverse Speed (%)
Min Reverse Speed (%)
Speed Limit Pot Enabled
Fast
30
15
35
20
100
30
50
50
Off
Operation Settings
Sleep timer (minutes)
Throttle Invert
20
No
Battery Settings
Low battery Flash Level (Bars)
Cable Resistance (milli-Ohms
Calibration Factor
Low Battery Alarm
2
40
100
Off
Inhibit Settings
Inhibit 1: Mode
Inhibit 1: Operation
Inhibit 1: Speed (%)
Inhibit 2: Mode
Inhibit 2: Operation
Inhibit 2: Speed (%)
Inhibit 3: Mode
Inhibit 3: Operation
Inhibit 3: Speed (%)
Aux Output: Mode
General Settings
Soft Stop
Brake Time (milli-seconds)
Output Voltage (Volts)
Status Output Type
Diagnostic Flash Sequence
Reverse Alarm
Pulsed Reverse Alarm
Diagnostic Alarm
Brake Disconnected Alarm
Brake Fault Detect
Brake Light
Freewheel Speed Limit
Freewheel Time Out (0,01 Seconds)
Freewheel Enable
Inhibit 2 Horn Input Enable
Version 2013v1
1
Latching
0
1
Non Latching
50
1
Latching
0
0
Off
900
24
2
0
Off
Off
Off
Off
On
On
35
20
Disable
Off
Slow
35
13
40
25
100
30
40
40
Motor Settings
Current Limit Max (Amps)
Boost Drive Current (Amps)
Boost Drive Time (Seconds)
Current Foldback Threshold (Amps)
Curerent Foldback Time (Seconds)
Current Foldback Level (%)
Motor Cooling Time (Seconds)
Current Foldback Temperature (Deg C)
Current Limit Min (Amps)
Motor Compensation (milli Ohms)
Anti Rollback Level
Pull-away Delay (centi-Seconds)
Slope Factor
Anti Rollback Velocity
110
120
10
80
70
59
660
30
10
20
12
0
1275
90
Factory Settings
Acceleration (0,1 Seconds)
Deceleration (0,1 Seconds)
Forward Speed (%)
Reverse Speed (%)
Max
100
100
100
100
Throttle Settings
Throttle Type
Throttle Deadband (%)
Throttle Gain (%)
Throttle Operated at Power-up
Throttle Reference Test
Iso Test Resistor
1
15
100
2
On
On
Min
1
1
0
0
(0 = Drive, 1 = Inhibit, 2 = Trip)
(0 = Trucharge, 1 = LED, 2 = Analogue)
15
Drive programs
3.3
Controller settings Winner S-drive 140A Schmid.
Winner S-Drive 140 15kmh Schmid
Speed Settings
Forward Acceleration (0,1 Seconds)
Forward Deceleration (0,1 Seconds)
Reverse Acceleration (0,1 Seconds)
Reverse Deceleration (0,1 Seconds)
Max Forward Speed (%)
Min Forward Speed (%)
Max Reverse Speed (%)
Min Reverse Speed (%)
Speed Limit Pot Enabled
Fast
40
15
35
60
100
30
30
15
Off
Operation Settings
Sleep timer (minutes)
Throttle Invert
20
No
Battery Settings
Low battery Flash Level (Bars)
Cable Resistance (milli-Ohms
Calibration Factor
Low Battery Alarm
2
40
100
Off
Inhibit Settings
Inhibit 1: Mode
Inhibit 1: Operation
Inhibit 1: Speed (%)
Inhibit 2: Mode
Inhibit 2: Operation
Inhibit 2: Speed (%)
Inhibit 3: Mode
Inhibit 3: Operation
Inhibit 3: Speed (%)
Aux Output: Mode
General Settings
Soft Stop
Brake Time (milli-seconds)
Output Voltage (Volts)
Status Output Type
Diagnostic Flash Sequence
Reverse Alarm
Pulsed Reverse Alarm
Diagnostic Alarm
Brake Disconnected Alarm
Brake Fault Detect
Brake Light
Freewheel Speed Limit
Freewheel Time Out (0,01 Seconds)
Freewheel Enable
Inhibit 2 Horn Input Enable
16
1
Latching
0
1
Non Latching
50
1
Latching
0
0
Off
900
24
2
0
Off
Off
Off
Off
On
On
35
20
Disable
Off
Slow
35
13
40
25
100
30
40
40
Motor Settings
Current Limit Max (Amps)
Boost Drive Current (Amps)
Boost Drive Time (Seconds)
Current Foldback Threshold (Amps)
Curerent Foldback Time (Seconds)
Current Foldback Level (%)
Motor Cooling Time (Seconds)
Current Foldback Temperature (Deg C)
Current Limit Min (Amps)
Motor Compensation (milli Ohms)
Anti Rollback Level
Pull-away Delay (centi-Seconds)
Slope Factor
Anti Rollback Velocity
130
140
10
80
70
59
660
30
10
20
12
0
1275
0
Factory Settings
Acceleration (0,1 Seconds)
Deceleration (0,1 Seconds)
Forward Speed (%)
Reverse Speed (%)
Max
100
100
100
100
Throttle Settings
Throttle Type
Throttle Deadband (%)
Throttle Gain (%)
Throttle Operated at Power-up
Throttle Reference Test
Iso Test Resistor
1
15
100
2
On
On
Min
1
1
0
0
(0 = Drive, 1 = Inhibit, 2 = Trip)
(0 = Trucharge, 1 = LED, 2 = Analogue)
Version 2013v1
Drive programs
3.4
Controller settings Winner S-drive 140A Schmid Alpine.
Winner S-Drive 140 15kmh Schmid Alpine
Speed Settings
Forward Acceleration (0,1 Seconds)
Forward Deceleration (0,1 Seconds)
Reverse Acceleration (0,1 Seconds)
Reverse Deceleration (0,1 Seconds)
Max Forward Speed (%)
Min Forward Speed (%)
Max Reverse Speed (%)
Min Reverse Speed (%)
Speed Limit Pot Enabled
Fast
45
15
35
60
100
30
30
20
Off
Operation Settings
Sleep timer (minutes)
Throttle Invert
20
No
Battery Settings
Low battery Flash Level (Bars)
Cable Resistance (milli-Ohms
Calibration Factor
Low Battery Alarm
2
40
100
Off
Inhibit Settings
Inhibit 1: Mode
Inhibit 1: Operation
Inhibit 1: Speed (%)
Inhibit 2: Mode
Inhibit 2: Operation
Inhibit 2: Speed (%)
Inhibit 3: Mode
Inhibit 3: Operation
Inhibit 3: Speed (%)
Aux Output: Mode
General Settings
Soft Stop
Brake Time (milli-seconds)
Output Voltage (Volts)
Status Output Type
Diagnostic Flash Sequence
Reverse Alarm
Pulsed Reverse Alarm
Diagnostic Alarm
Brake Disconnected Alarm
Brake Fault Detect
Brake Light
Freewheel Speed Limit
Freewheel Time Out (0,01 Seconds)
Freewheel Enable
Inhibit 2 Horn Input Enable
Version 2013v1
1
Latching
0
1
Non Latching
50
1
Latching
0
0
Off
900
24
2
0
Off
Off
Off
Off
On
On
35
20
Disable
Off
Slow
35
13
40
25
100
30
40
40
Motor Settings
Current Limit Max (Amps)
Boost Drive Current (Amps)
Boost Drive Time (Seconds)
Current Foldback Threshold (Amps)
Curerent Foldback Time (Seconds)
Current Foldback Level (%)
Motor Cooling Time (Seconds)
Current Foldback Temperature (Deg C)
Current Limit Min (Amps)
Motor Compensation (milli Ohms)
Anti Rollback Level
Pull-away Delay (centi-Seconds)
Slope Factor
Anti Rollback Velocity
130
140
10
80
70
59
660
30
10
15
12
0
1275
0
Factory Settings
Acceleration (0,1 Seconds)
Deceleration (0,1 Seconds)
Forward Speed (%)
Reverse Speed (%)
Max
100
100
100
100
Throttle Settings
Throttle Type
Throttle Deadband (%)
Throttle Gain (%)
Throttle Operated at Power-up
Throttle Reference Test
Iso Test Resistor
1
15
100
2
On
On
Min
1
1
0
0
(0 = Drive, 1 = Inhibit, 2 = Trip)
(0 = Trucharge, 1 = LED, 2 = Analogue)
17
Drive programs
3.5
Controller settings Winner S-drive 140A CT Reduced speed.
Winner S-Drive 140 15kmh CT Reduced Speed
Only for Winners with the following serial numbers:
PW00001 t/m PW00288
NW01950 t/m NW02237
NW1865
NW05106
Speed Settings
Forward Acceleration (0,1 Seconds)
Forward Deceleration (0,1 Seconds)
Reverse Acceleration (0,1 Seconds)
Reverse Deceleration (0,1 Seconds)
Max Forward Speed (%)
Min Forward Speed (%)
Max Reverse Speed (%)
Min Reverse Speed (%)
Speed Limit Pot Enabled
Fast
30
15
35
60
90
30
36
20
Off
Operation Settings
Sleep timer (minutes)
Throttle Invert
20
No
Battery Settings
Low battery Flash Level (Bars)
Cable Resistance (milli-Ohms
Calibration Factor
Low Battery Alarm
2
40
100
Off
Inhibit Settings
Inhibit 1: Mode
Inhibit 1: Operation
Inhibit 1: Speed (%)
Inhibit 2: Mode
Inhibit 2: Operation
Inhibit 2: Speed (%)
Inhibit 3: Mode
Inhibit 3: Operation
Inhibit 3: Speed (%)
Aux Output: Mode
General Settings
Soft Stop
Brake Time (milli-seconds)
Output Voltage (Volts)
Status Output Type
Diagnostic Flash Sequence
Reverse Alarm
Pulsed Reverse Alarm
Diagnostic Alarm
Brake Disconnected Alarm
Brake Fault Detect
Brake Light
Freewheel Speed Limit
Freewheel Time Out (0,01 Seconds)
Freewheel Enable
Inhibit 2 Horn Input Enable
18
1
Latching
0
1
Non Latching
50
1
Latching
0
0
Off
1000
24
2
0
Off
Off
Off
Off
On
On
35
20
Disable
Off
Slow
35
13
40
25
90
30
36
20
Motor Settings
Current Limit Max (Amps)
Boost Drive Current (Amps)
Boost Drive Time (Seconds)
Current Foldback Threshold (Amps)
Curerent Foldback Time (Seconds)
Current Foldback Level (%)
Motor Cooling Time (Seconds)
Current Foldback Temperature (Deg C)
Current Limit Min (Amps)
Motor Compensation (milli Ohms)
Anti Rollback Level
Pull-away Delay (centi-Seconds)
Slope Factor
Anti Rollback Velocity
130
140
10
80
70
59
660
30
10
20
12
0
950
0
Factory Settings
Acceleration (0,1 Seconds)
Deceleration (0,1 Seconds)
Forward Speed (%)
Reverse Speed (%)
Max
100
100
100
40
Throttle Settings
Throttle Type
Throttle Deadband (%)
Throttle Gain (%)
Throttle Operated at Power-up
Throttle Reference Test
Iso Test Resistor
1
15
100
2
On
On
Min
1
1
0
0
(0 = Drive, 1 = Inhibit, 2 = Trip)
(0 = Trucharge, 1 = LED, 2 = Analogue)
Version 2013v1
Drive programs
3.6
Controller settings Winner S-drive 140A CT.
Winner S-Drive 140 15kmh CT
Speed Settings
Forward Acceleration (0,1 Seconds)
Forward Deceleration (0,1 Seconds)
Reverse Acceleration (0,1 Seconds)
Reverse Deceleration (0,1 Seconds)
Max Forward Speed (%)
Min Forward Speed (%)
Max Reverse Speed (%)
Min Reverse Speed (%)
Speed Limit Pot Enabled
Fast
30
15
35
60
100
30
40
20
Off
Operation Settings
Sleep timer (minutes)
Throttle Invert
20
No
Battery Settings
Low battery Flash Level (Bars)
Cable Resistance (milli-Ohms
Calibration Factor
Low Battery Alarm
2
40
100
Off
Inhibit Settings
Inhibit 1: Mode
Inhibit 1: Operation
Inhibit 1: Speed (%)
Inhibit 2: Mode
Inhibit 2: Operation
Inhibit 2: Speed (%)
Inhibit 3: Mode
Inhibit 3: Operation
Inhibit 3: Speed (%)
Aux Output: Mode
General Settings
Soft Stop
Brake Time (milli-seconds)
Output Voltage (Volts)
Status Output Type
Diagnostic Flash Sequence
Reverse Alarm
Pulsed Reverse Alarm
Diagnostic Alarm
Brake Disconnected Alarm
Brake Fault Detect
Brake Light
Freewheel Speed Limit
Freewheel Time Out (0,01 Seconds)
Freewheel Enable
Inhibit 2 Horn Input Enable
Version 2013v1
1
Latching
0
1
Non Latching
50
1
Latching
0
0
Off
1000
24
2
0
Off
Off
Off
Off
On
On
35
20
Disable
Off
Slow
35
13
40
25
100
30
40
20
Motor Settings
Current Limit Max (Amps)
Boost Drive Current (Amps)
Boost Drive Time (Seconds)
Current Foldback Threshold (Amps)
Curerent Foldback Time (Seconds)
Current Foldback Level (%)
Motor Cooling Time (Seconds)
Current Foldback Temperature (Deg C)
Current Limit Min (Amps)
Motor Compensation (milli Ohms)
Anti Rollback Level
Pull-away Delay (centi-Seconds)
Slope Factor
Anti Rollback Velocity
130
140
10
80
70
59
660
30
10
20
12
0
950
0
Factory Settings
Acceleration (0,1 Seconds)
Deceleration (0,1 Seconds)
Forward Speed (%)
Reverse Speed (%)
Max
100
100
90
36
Throttle Settings
Throttle Type
Throttle Deadband (%)
Throttle Gain (%)
Throttle Operated at Power-up
Throttle Reference Test
Iso Test Resistor
1
15
100
2
On
On
Min
1
1
0
0
(0 = Drive, 1 = Inhibit, 2 = Trip)
(0 = Trucharge, 1 = LED, 2 = Analogue)
19
Front Signal Light Wire
20
HORN
S/W
LAMP
Charge
connector
batt. right.
harness
batt.left
harness
100A
100A
motor
M
3.7
fuse
5A
S-Drive 140
Normally closed
freewheel switch
EM Brake 24V 1.25A
Transaxle incl.
wiring
Electrical diagrams
Electrical Diagram S-Drive
Version 2013v1
fuse 24V+
15A
1423111A
KEY S/W
Electrical diagrams
3.8
Connections printed circuit board
1
CN4
2
CN3
6
3
CN14
5
CN1
CN8
14
CN12
4
CN5
13
CN13
12
CN11
8
11
CN10
CN7
10
CN9
9
CN6
7
CN2
The
PCB
connecti
ons are
stated in
the
table below.
Number
1
2
3
4
5
6
Connection Number
CN4
CN3
CN1
CN5
CN8
CN14
7
CN2
8
9
10
11
12
13
14
CN7
CN6
CN9
CN10
CN11
CN13
CN12
Version 2013v1
Function
Lighting switch
Head light
Main harness
Throttle
Key Switch
Horn switch left
Speed potentiometer/ Horn switch right / Battery
indicator
Horn
Hazard light switch
Indicator switch right
Indicator switch left
Indicator right
Indicator left
Not used
21
Electrical diagrams
4 Technical specifications
XXXXXX-010900000-nl.doc
4.1
Product specifications
Manufacturer
4.1.1
Handicare Nederland b.v.
Winner
Model
Maximum user's weight
3 Wheel
159 kg
4 Wheel
159 kg
Description
Total length
Total width
Minimal height (without chair and tiller folded
downwards)
Total weight incl. batteries
Weight of heaviest part
Static stability downward
Static stability upward
Static stability sideways
Energy consumption: theoretic maximum
distance
Dynamic stability on slopes
Climbing capacity for obstacles
Maximal speed forward
Minimum brake distance from maximum speed
Seat angle
Effective seating depth
Effective seating width
Sitting height from the front
(adjustable in steps of 25 mm (0.8"))
Back angle
Back height
Armrest height
3 Wheel
1410 mm
673 mm
4 Wheel
1410 mm
673 mm
1000 mm
1000 mm
153 kg (80Ah)
n.v.t.
15°
15°
15°
158 kg (80Ah)
n.v.t.
15°
15°
15°
60 km (80Ah)
60 km (80Ah)
11°
100 mm
15 km/u
2°
430 mm
500 mm
455 mm-520 mm
11°
100 mm
15 km/u
2°
430 mm
500 mm
455 mm-520 mm
85°-180°
85°-180°
550 mm
250 mm
550 mm
250 mm
3 Wheel
260 mm
1400 mm
100 mm
114 mm
< 2000 mm
4 Wheel
260 mm
1905 mm
100 mm
114 mm
< 2000 mm
Test data
Weight test dummy
3 Wheel
159 kg
4 Wheel
Operating force
Operating-handle power
Resetting automatic fuse
Electronic switches
Parking brake
Inserting charging plug
3 Wheel
< 60 N
< 60 N
< 15 N
< 60 N
< 60 N
4 Wheel
< 60 N
< 60 N
< 15 N
< 60 N
< 60 N
3 Wheel
310 x 108 mm
310 x 108 mm
270 kPa (2,7 Bar)
4 Wheel
292 x 108 mm
310 x 108 mm
270 kPa (2,7 Bar)
Omschrijving
Front armrest to backrest
Minimum radius
Capacity to drive over obstacles
Ground clearance
Turning space
Technical data
Diameter front wheel
Diameter rear wheels
Tire pressure wheels
22
Version 2013v1
Technical specifications
Batteries
Maximum dimensions batteries
Weight scooter without batteries
Battery capacity
Maximum permissible charging voltage
Maximum charging current
Connector type
3 Wheel
324 x 175 x 213 mm
93 kg
80 Ah/20h
13,6 V
7A
A DIN 72311
4 Wheel
324 x 175 x 213 mm
98 kg
80 Ah/20h
13,6 V
7A
A DIN 72311
4.2
Approval
The product meets the following standards:
1.
NEN-EN 12182 Technical tools for the handicapped - General standards and testing methods October 1997.
2.
NEN-EN 12184 Electrically driven wheelchairs, scooters and associated charging equipment - Standards and
testing methods April 1999.
3.
The Winner 3-wheel scooter is classified according to EN12184 (1999) in class C.
4.
ISO 7176-8 Requirements and test methods for impact, static, and fatigue strength July 1998.
5.
ISO 7176-9 climate tests for electric wheelchairs and scooters.
6.
ISO 7176-14 Standards and test methods for controller systems of electrically driven wheelchairs 1997.
7.
ISO 7176-16 Requirements of resistance to fire, May 1997.
4.3
Service information transaxles.
Service-check for:
Part
Winner with Schmid transaxle
Winner with CT transaxle
Carbon brushes
Once a year or every 3000 Km
Once a year or every 3000 Km
Length off carbon brush
16mm new / 8mm end length
18mm new / 8mm end length
24
Version 2013v1
Parts lists
5
Use of the parts lists
This document is meant as a reference book to be able to order parts for the scooter as shown on the front.
How to order:
To order parts please specify:
• Serial number (see the identification plate).
• Group (to which the relevant part belongs).
• Article number.
• Number of parts required.
• Description (in the relevant language).
• Dimensions (if applicable).
Remark:
• If a part does not have a position number, it means that the relevant part cannot be bought separately. The relevant
part is part of the composition that is shown. Only the composition can be ordered, so it must be replaced in its entirety.
• Boxed position numbers refer to the relevant drawing.
Order address:
Please send orders by post or fax to your supplier.
Service technicians:
Repairs may only be done by trained and authorized service technicians.
In the execution of their work they are at all times fully responsible for the fulfilment of locally applicable safety
guidelines and standards.
Temporary employees and persons in training may only execute repair and replacement work under the
supervision of an authorized service technician.
XXXXXX-020904000-en.doc
Version 2013v1
25
Parts lists
Winner 2004
Winner 2004
001: SCOOTER ASSY (3W)
Pos
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
26
Article number
No spare part
20456.0682
9003154
00000.4134
1001675
00000.1702
161.00151.000
00000.3200
00000.1700
161.00161.000
1009683
161.00171.000
001.03160.001
001.03160.002
161.00181.000
00000.2101
Units
1
1
1
2
4
2
1
4
4
1
1
1
2
2
2
4
Description
3W Scooter assy
Rubber bellow
Tiller parallel assy
Screw M8xP1.25x35L
Arc Washer
Lock nut M8
Console bottom cover assy
Screw M5xP0.8x12L
Lock nut M5xP0.8
Console panel cover assy (Solo)
Console panel cover assy (S-Drive)
Console top cover assy
Screw 2,9x16mm
Screw 2,9x25mm
Block (Bush 12mm)
Flat washer M5
Version 2013v1
Parts lists
Winner 2004
Winner 2004
002: SCOOTER ASSY (4W)
Pos
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Article number
No spare part
20456.0682
9003154
00000.4134
1001675
00000.1702
161.00151.000
00000.3200
00000.1700
161.00161.000
1009683
161.00171.000
001.03160.001
001.03160.002
161.00181.000
00000.2101
Version 2013v1
Units
1
1
1
2
4
2
1
4
4
1
1
1
2
2
2
4
Description
4W Scooter assy
Rubber bellow
Tiller parallel assy
Screw M8xP1.25x35L
Arc Washer
Lock nut M8
Console bottom cover assy
Screw M5xP0.8x12L
Lock nut M5xP0.8
Console panel cover assy (Solo)
Console panel cover assy (S-Drive)
Console top cover assy
Screw 2,9x16mm
Screw 2,9x25mm
Block (Bush 12mm)
Flat washer M5
27
Parts lists
Winner 2004
003: CONSOLE TOP COVER ASSY
Pos
1
2
3
4
-
28
Article number
1001334
1001335
1001336
264.00121.000
161.00171.000
Units
1
1
1
4
1
Description
Console top cover
Head light assy
Head light seal
Head light DC24 3W
Console top cover assy
Version 2013v1
Parts lists
Winner 2004
Winner 2004
004: CONSOLE BOTTOM COVER ASSY
Pos
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
-
Article number
1001321
9003156
1001323
1001208
1001324
1001325
1001326
1001327
1001328
1001329
008.00000.481
1001281
1001331
1001332
1001333
No spare part
161.00151.000
1001372
Version 2013v1
Units
1
1
2
1
4
1
2
2
1
1
2
2
1
1
2
2
1
1
Description
Console bottom cover
Potentionmeter cable assy
Screw 4,2x12mm
PCB tiller
Screw 2,9x8mm
Horn
Front indicator assy
Toggle switch wire assy
Key switch wire assy
Console fuse wire assy
Label "indicator arrows"
Bulb DC24V 5W T9.5
Fuse 2A glass
Head light extend wire assy
Console indicator assy
Plastic washer
Console bottom cover assy
Contact key
29
Parts lists
Winner 2004
Winner 2004
005: CONSOLE PANEL ASSY
Pos
1
2
3
4
5
6
7
8
9
10
11
12
13
-
30
Article number
1001337
1001338
9003087
1001340
1001340
1001341
1001342
1001343
008.00000.601
008.00000.611
008.00000.621
1001344
1001345
1001346
161.00161.000
1009683
Units
1
1
1
1
1
1
1
1
1
1
1
2
2
2
1
1
Description
Console panel cover
Battery indicator + speedswitch (Solo)
Battery indicator + speedswitch (S-Drive)
Horn switch cable assy
Horn switch cable assy
Speed knob
Warning light control assy
Head light switch cable assy
Label Speed selector
Label console upper
Label console lower
Battery meter bracket
Screw M2,9x8mm
Stuff inserts the panel
Console panel assy (Solo)
Console panel assy (S-Drive)
Version 2013v1
Parts lists
Winner 2004
Winner 2004
006: WIG-WAG ASSY
Pos
1
2
3
4
5
6
7
8
9
-
Article number
No spare part
No spare part
No spare part
No spare part
1001355
1001356
9003092
9003093
00000.3503
9003155
Version 2013v1
Units
1
1
1
2
1
1
1
1
2
1
Description
Wig-wag
Finger control (LH)
Finger control (RH)
Screw M4xP0.7x8L black
Plastic tip finger (LH) (Green)
Plastic tip finger (RH) (Yellow)
Plastic tip thumb (LH) (Yellow)
Plastic tip thumb (RH) (Green)
Set screw M5xP0.8x5L
Wig-Wag assy
31
Parts lists
Winner 2004
Winner 2004
007: TILLER ASSY
Pos
1
2
3
4
5
6
7
8
9
10
11
12
13
-
32
Article number
9003091
125.00031.000
108.00281.000
00000.9002
1001313
1001308
1001315
1001316
1001317
1001318
1001311
00000.1402
1001320
9003154
Units
1
2
1
2
8
1
4
8
8
1
1
2
1
1
Description
Handle
Hand grip (foam)
Brake handle
Plug for hand grip 22x2
Pivot bush
Channel front assy
Pivot pin
Spring washer black
Screw M6xP1.0x10L black
Channel back
Pivot pin
Clip E7
Bottom mounting block of tiller
Tiller assy
Version 2013v1
Parts lists
Winner 2004
008: CHANNEL FRONT ASSY
Pos
1
2
3
4
5
Article number
1001309
1001310
1001311
00000.1402
1001312
Version 2013v1
Units
1
1
1
2
4
Description
Channel front
Gas spring
Pivot pin
Clip E7
Bush
33
Parts lists
Winner 2004
009: BACK TILLER SHROUD ASSY
Pos
1
2
3
4
5
6
7
8
34
Article number
1011153
1009684
008.00000.391
00001.1347
008.00000.371
1001361
9003485
9003484
1001286
00000.1506
No spare part
Units
1
1
1
1
1
1
1
1
2
2
1
Description
Back tiller shroud assy (Solo)
Back tiller shroud assy (S-Drive)
Label "charger"
Label "CE"
Label "tiller adjust"
Charger plug cable assy (Solo)
Charger plug cable assy (S-Drive) (15A)
Charger plug cover
Screw M3xP0.5x10L
Nut M3xP0.5
Label "charger set"
Version 2013v1
Parts lists
Winner 2004
010: SCOOTER ASSY (3W)
Pos
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
Article number
No spare part
108.00291.000
00000.7718
1011153
1009684
1001365
052.00342.000
1001366
1001367
1254
1001368
No spare part
No spare part
00000.4134
00000.2203
9000812
9001135
9003155
1001370
9000704
00000.3612
9000872
9002232
Version 2013v1
Units
1
1
1
1
1
4
1
6
6
3
1
1
1
1
1
1
1
1
2
1
1
Description
3W Scooter pro assy
Brake cable assy
P-clip ACC-4
Back tiller shroud assy (Solo)
Back tiller shroud assy (S-Drive)
Screw M4xP0.7x6L black
Front cover of tiller
Screw M4xP0.7x10L black
Flat washer W4 black
P-clip ACC-3
Hose clamp
X
X
Screw M8xP1.25x35L
Spring washer M8
Basket holder
Basket
Wig-wag assy
Tiller lever
Basket lock
Bolt M4*10
Tape
Handicare logo
35
Parts lists
Winner 2004
011: SCOOTER ASSY (4W)
Pos
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
-
36
Article number
170.00352.000
1004591
1011153
1009684
1001365
052.00342.000
1001366
1001367
1254
1001368
00000.4134
00000.2203
9000812
9001135
9003155
1001370
9000704
00000.3612
9000872
9002232
1009813
Units
1
1
1
1
4
1
6
6
4
1
1
1
1
1
1
1
1
2
1
1
1
Description
Rear wheel assy
Front wheel assy
Back tiller shroud assy (Solo)
Back tiller shroud assy (S-Drive)
Screw M4*P0.7*6mm
Tiller cover assy front
Screw M4*P.07*10mm
Washer Ø3*Ø6*0.5t
P-clip
Hose clamp
Bolt M8*P1.25*35mm
Spring washer M8
Basket holder
Basket
Wig-wag assy
Tiller lever
Basket lock
Bolt M4x10
Tape
Handicare logo
Brake cable assy 4W
Version 2013v1
Parts lists
Winner 2004
Winner 2004
012: FRONT TIRE ASSY (3W)
Pos
1
2
3
4
5
6
7
8
9
10
11
-
Article number
176.00182.000
172.00062.000
176.00191.000
00001.1462
173.00052.000
173.00042.000
171.00021.000
015.07030.001
00000.3706
00000.1802
00000.2203
170.00342.000
Version 2013v1
Units
1
1
1
1
1
1
1
2
5
5
5
1
Description
Brake hub
Outer tire 4.10x3.50x6"
Spacer Bush
Label max 2.7 bar
Outer Rim 6"
Inner Rim 6"
Tube Inner with Cap
Bearing 6202/2RS
Screw M8xP1.25x25L
Nut M8xP1.25
Spring washer SW8
Front tyre assy (3W)
37
Parts lists
Winner 2004
Winner 2004
013: FRONT FORK (3W)
Pos
1
2
3
4
5
6
7
8
-
38
Article number
No spare part
No spare part
No spare part
No spare part
No spare part
No spare part
No spare part
No spare part
110.00022.000
Units
1
2
4
2
2
1
1
2
1
Description
Fork Weldment
Tube cap
Nylon bearing
Spring stopper
Compression Spring
Lower tube weldment (LH)
Lower tube weldment (RH)
Dust cap
Front fork (3W)
Version 2013v1
Parts lists
Winner 2004
014: FRONT FORK ASSY (3W)
Pos
1
2
3
4
5
6
7
8
9
Article number
170.00342.000
110.00022.000
00000.2003
00000.2203
1009325
176.00172.000
176.00251.000
108.00271.000
1001257
Version 2013v1
Units
1
1
2
2
2
1
1
1
2
Description
Front wheel assy (3W)
Front fork assy
Flat washer M8
Spring washer M8
Bolt M8x25 (10.9)
Axle for front wheel
Collar for front wheel
Break assy for front wheel
Nut M14xP1.5
39
Parts lists
Winner 2004
015: FRONT FRAME ASSY (3W)
Pos
1
2
3
4
5
6
7
8
9
10
40
Article number
110.00072.000
No spare part
015.07010.002
126.00011.000
No spare part
00000.4104
00000.2002
00000.1701
1001261
No spare part
Units
1
1
1
1
2
4
8
4
6
-
Description
Front frame weldment
Front fork & wheel assy
Head set
Front bumper
Snap button
Screw M6xP1.0x55L
Flat washer W6
Lock nut M6xP1.0
Nut-inserts
X
Version 2013v1
Parts lists
Winner 2004
016: FRONT FRAME ASSY (4W)
Pos
1
2
3-8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Article number
1004626
1004581
015.07010.002
1001261
1004582
1004583
00000.4110
00000.1703
001.03010.003
00000.2103
1004584
1004585
00000.1702
1004586
1004597
1004598
1004588
1004589
1004587
Version 2013v1
Units
1
1
1
10
1
1
2
2
2
4
4
2
6
1
4
2
2
2
1
Description
Frontframe 4w weldment
Steering tube
Head set
Insert
Knuckle RHS
Knuckle LHS
Bolt M10xP1.5*70mm
Nut M10*P1.5
Bolt M8*P1.25*125mm
Washer Ø8*Ø16*1.5
Plug Ø30*20mm
Spring Ø26.5*Ø16.5*94.5mm
Nut M8*P1.25
Rod Ø8*140mm
Nut (rod) M8*P1.25
Nut (rod) M8*P1.25
Bearing (rod)
Bearing (rod)
Rod Ø8*300mm
41
Parts lists
Winner 2004
016: FRONT FRAME ASSY (4W)
Pos
25
26
27
28
29
30
31
32
33
34
35
36
42
Article number
1004591
00000.2005
00000.1703
1004593
00000.4135
1004594
1004595
00000.1502
00000.4311
1004596
00000.2203
00000.2103
Units
2
2
2
4
2
1
1
4
4
2
4
4
Description
Front wheel assy
Washer Ø12*Ø19*1.0
Lock nut M12*P1.75
Bush Ø16*8mm
Bolt M8*P1.25*25mm
Brake assy RHS
Brake assy LHS
Nut M8*P1.25
Bolt M8*P1.25*20mm
Strip 5t*30*100
Spring Washet M8 SW8
Washer Ø8*Ø16*2.0t
Version 2013v1
Parts lists
Winner 2004
017: KNUCKLE RHS ASSY (4W)
Pos
1
2
3
4
5
6
7
-
Article number
1004599
1004600
1004601
00000.2003
00000.1702
1004602
1004603
1004582
Version 2013v1
Units
1
1
2
1
1
1
2
1
Description
Bracket
Knuckle
Ball bearing
Washer M8
Nut M8*P1.5
Bolt M8*P1.5
Washer
Knuckle RHS assy (4W)
43
Parts lists
Winner 2004
018: KNUCKLE LHS ASSY (4W)
Pos
1
2
3
4
5
6
7
-
44
Article number
1004604
1004605
1004601
00000.2003
00000.1702
1004602
1004603
1004583
Units
1
1
2
1
1
1
2
1
Description
Bracket
Knuckle
Ball bearing
Washer M8
Nut M8*P1.5
Bolt M8*P1.5
Washer
Knuckle LHS assy (4W)
Version 2013v1
Parts lists
Winner 2004
019: FLOORPAN ASSY (3W)
Pos
1
2
3
4
5
6
7
-
Article number
No spare part
1001273
00001.1110
126.00032.000
126.00042.000
001.15010.002
008.00000.401
1012256
Version 2013v1
Units
1
2
4
1
1
6
1
1
Description
Front cover 3w
Shroud "J" bracket
Rivet pop
Bumper trim (LH)
Bumper trim (RH)
Snap button
Label "Winner"
Floorpan assy (3W) with floor mat
45
Parts lists
Winner 2004
020: SCOOTER ASSY (3W)
Pos
1
2
3
4
5
6
7
8
9
10
11
12
13
46
Article number
No spare part
1012256
00000.3304
257.00001.000
1001276
00001.1110
00000.2108
138.00011.000
001.15010.001
1001277
1001385
9003107
055.00401.000
005.01210.000
Units
1
1
4
1
1
1
1
2
8
4
1
1
1
1
Description
Body frame assy
Front floorpan assy with floor mat
Screw 4,2x16
Floor mat 3w
Holding Elastic Band
Rivet pop 4-4
Flat washer W3
Battery strap
Rivet pop 6-3
Battery mat
Main wire (Solo)
Main wire (S-Drive)
Charger extend cable
Fuse 15A
Version 2013v1
Parts lists
Winner 2004
021: FLOORPAN ASSY (4W)
Pos
1
2
3
4
5
6
-
Article number
1004579
1001273
00001.1110
1004580
1004198
008.00000.401
1004575
Version 2013v1
Units
1
2
4
2
6
1
1
Description
Front cover
Bracket 2t*10*80
Pop rivet
Side strip 5t*25*380L
Snap button
Label "Winner"
Floorpan assy (4W)
47
Parts lists
Winner 2004
022: SCOOTER ASSY (4W)
Pos
1
2
3
4
5
6
7
8
9
10
11
12
13
14
48
Article number
No spare part
1004575
00000.3304
1004576
1004577
1001276
00001.1110
00000.2108
138.00011.000
001.15010.001
1001277
126.00021.000
00000.2004
00000.1703
Units
1
1
4
1
2
1
1
1
2
8
4
1
2
2
Description
Main frame assy
Front cover assy
Screw M4*16mm
Floor mat 3.0t*390*490
Foot step 3.0t*107*188
Elastic strap
Pop rivet
Washer M3
Battery strap 38mm*800mm
Pop rivet
Battery mat 2.0t*45*145
Bumper front 4w
Washer M10
Nut M10*P1.5
Version 2013v1
Parts lists
Winner 2004
023: BODY FRAME ASSY (3W)
Pos
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Article number
No spare part
No spare part
110.00141.000
00000.1402
See 028 and 029
No spare part
1001266
1012699
00000.2004
00000.1703
013.00000.022
00000.4110
00000.2104
1001267
1001268
1001269
00000.2004
1001233
1001271
Version 2013v1
Units
1
1
2
2
1
4
4
8
4
2
2
12
2
4
5
2
2
2
Description
Front frame assy
Rear frame assy
Axle for rear frame
Clip E7
Transaxle assy
X
Screw M10xP1.5x90L (for Schmid transaxle)
Screw M10xP1.5x100L (for CT transaxle)
Flat washer M10
Lock nut M10xP1.5
Shock absorber
Screw M10xP1.5x70L
Flat washer M10
Screw M10xP1.5x50L
Velcro-hooks
Velcro-hooks
Flat washer M10
Bushing
Bushing
49
Parts lists
Winner 2004
024: BODY FRAME ASSY (4W)
Pos
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
50
Article number
No spare part
No spare part
00000.4105
00000.1502
See 028 and 029
1001266
1012699
00000.2004
00000.1703
013.00000.022
00000.2104
00000.4110
1001268
1001269
00000.2003
9000689
1004606
Units
1
1
2
2
1
6
4
8
8
2
12
2
4
5
4
2
2
Description
Front frame assy 4w
Rear frame assy (modified)
Bolt M8xP1.25*40mm
Nut M8*P1.25
Transaxle assy
Screw M10xP1.5x90L (for Schmid transaxle)
Screw M10xP1.5x100L (for CT transaxle)
Washer M10*P1.5*90mm
Nut M10*P1.5
Shock absorber 10*27*1.8t
Washer M10
Bolt M10*P1.5*50mm
Velcro hooks strip
Velcro hooks strip
Washer M8
Rubber transaxle strip
Bush 20*8mm
Version 2013v1
Parts lists
Winner 2004
025: REAR FRAME ASSY
Pos
1
2
3
4
5
6
7
8
9
10
11
-
Article number
110.00082.000
No spare part
00001.1110
1010353
00000.2003
00000.1702
1001232
126.00021.000
00000.2004
00000.1703
1001233
1001230
Version 2013v1
Units
1
1
2
4
8
2
2
1
2
2
4
1
Description
Rear Suspension Bridge
Label "serial number"
Rivet pop
Plastic wheel
Flat washer M8 black
Lock nut M8xP1.25 black
Screw M8xP1.25x75L black
Rear bumper
Flat washer M10
Lock nut M10xP1.5
Bushing
Rear frame assy
51
Parts lists
Winner 2004
026: REAR TIRE ASSY
Pos
1
2
3
4
5
6
7
8
9
10
-
52
Article number
176.00202.000
172.00051.000
176.00191.000
00001.1462
173.00052.000
173.00042.000
171.00021.000
00000.4135
00000.2203
00000.1802
170.00352.000
Units
1
1
1
1
1
1
1
5
5
5
2
Description
Hub
Outer tire 4.10x3.50x6"
Spacer Bush
Label max 2.7 bar
Outer Rim 6"
Inner Rim 6"
Tube Inner with Cap
Screw M8xP1.25x25L
Spring washer SW8
Nut M8xP1.25
Rear tire assy
Version 2013v1
Parts lists
Winner 2004
027: TRANSAXLE ASSY
Pos
1
2
3
4
5
6
7
Article number
See 028 and 029
1001246
1001247
170.00352.000
1001387
00000.1703
1001242
1011586
Version 2013v1
Units
1
2
2
2
2
2
1
1
Description
Transaxle
Collar
Set Screw M8xP1.25x5L
Rear tire Assy
Flat washer 12x24x2.5
Lock nut M12xP1.75
Freewheel lever for Schmid transaxle
Freewheel lever for CT transaxle
53
Parts lists
Winner 2004
028: TRANSAXLE STANDARD
Pos
7
8
Article number
1002356
1009685
1012904
No spare part
1003267
9003297
1011584
1002646
103.00031.000
1011585
1001239
103.00091.000
1012123
9000689
No spare part
-
1003209
1
2
3
4
5
6
54
Units
1
1
1
1
1
1
1
2
2
1
2
2
2
2
1
Description
Transaxle Schmid (Solo)
Transaxle Schmid (S-Drive)
Transaxle CT (S-Drive)
Motor 15 kmph
Brake Assy Schmid
Brake Assy Schmid from 09-2008 + S-Drive
Brake Assy CT
Motor brush till 08-2008
Motor brush from 09-2008
Motor brush set CT
Clip E19
Wedge for Schmid transaxle
Wedge for CT transaxle
Transaxle mat
Friction plate for Schmid transaxle
Version 2013v1
Parts lists
Winner 2004
029: TRANSAXLE ALPINE
Pos
5
6
7
8
Article number
9003239
1009686
No spare part
1003267
9003297
1002646
103.00031.000
1001239
103.00091.000
9000689
No spare part
-
1003209
1
2
3
4
Version 2013v1
Units
1
1
1
1
1
2
2
2
2
2
1
Description
Transaxle Alpine, Solo (max. 9 km/h)
Transaxle Alpine, S-Drive (max. 9 km/h)
Motor 15 kmph
Brake Assy
Brake Assy Schmid from 09-2008 + S-Drive
Motor brush till 08-2008
Motor brush from 09-2008
Clip E19
Wedge
Transaxle mat
Friction plate
55
Parts lists
Winner 2004
030: SCOOTER ASSY (3W)
Pos
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
56
Article number
No spare part
No spare part
00000.3200
No spare part
052.00312.000
052.00452.000
1001302
1001303
1001304
1001305
1001306
055.00421.000
9003109
005.01180.000
9003553
055.00431.000
9003108
9002752
99117
1001307
00000.1700
00000.3204
Units
1
1
6
1
1
1
1
2
1
2
1
1
1
1
1
2
2
2
2
1
1
1
Description
3W scooter assy
Controller assy
Screw M5xP0.8x12L
Controller cover assy
Rear motor cover assy
Battery cover assy
Transaxle plate (LH)
Screw M5xP0.8x30L
Transaxle plate (RH)
Bush
Star knob
Controller wire assy (Solo)
Power harness (S-Drive)
Fuse 5A (Solo)
Fuse 5A (S-Drive)
Battery power wire (Solo)
Battery power wire (S-Drive)
Set battery connection covers
Fuse 100A (S-Drive)
Fix bracket rear shroud
Lock nut M5xP0.8
Screw M5xP0.8x25L
Version 2013v1
Parts lists
Winner 2004
031: SCOOTER ASSY (4W)
Pos
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Article number
No spare part
No spare part
00000.3200
1001288
052.00312.000
052.00452.000
1001302
1001303
00000.3204
1001304
1001305
1001306
1001307
00000.1700
No spare part
Version 2013v1
Units
1
1
6
1
1
1
1
2
1
1
2
1
1
1
1
Description
4w scooter por assy
Controller assy
Bolt M5*P0.8*12mm
Controller cover
Rear cover assy
Battery cover assy
Mud guard 1.2t*168*187 LH
Bolt M5*P0.8*30mm
Bolt M5*P0.8*25mm
Mud guard 1.2t*168*187 RH
Bush 12*23mm
Knob
Bracket for rear cover
Lock nut M5*P0.8
Twist cable clip
57
Parts lists
Winner 2004
032: BATTERY COVER ASSY
Pos
1
2
3
4
5
-
58
Article number
No spare part
008.00000.591
1001284
00000.2009
1001286
052.00452.000
Units
1
1
1
2
1
1
Description
Battery cover
Label circuit diagram
Window post
Flat washer M3
Screw M3xP0.5x10L
Battery cover assy
Version 2013v1
Parts lists
Winner 2004
033: REAR MOTOR COVER ASSY
Pos
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
-
Article number
052.00392.000
264.00101.000
1014195
008.00000.411
008.00000.421
008.00000.401
1001268
1001269
126.00052.000
001.15010.002
1001280
00000.3600
00000.1705
051.00021.000
00000.2001
00000.1700
008.00000.291
1001281
055.00411.000
052.00312.000
Version 2013v1
Units
1
1
1
1
1
1
2
2
2
4
1
2
2
1
1
1
2
4
1
1
Description
Rear motor cover
Rear indicator assy (orange)
Rear light assy (red)
Label engage/release
Label circuit breaker
Label "Winner"
Velcro-loops
Velcro-loops
Bumper trim
Snap button
Break light assy
Screw M4xP0.7x16L
Lock nut M4xP0.7
Reflector (red)
Flat washer M5
Lock nut M5xP0.8
Label movingpeople.net
Bulb DC24V 5W T9.5
Rear light cable assy
Rear motor cover assy
59
Parts lists
Winner 2004
034: CONTROLLER COVER ASSY
Pos
1
2
3
4
60
Article number
1001288
1001268
1001290
1001291
Units
1
5
1
1
Description
Cover of controller
Velcro-loops
Circuit breaker 60A (Solo)
Cap of circuit breaker 60A (Solo)
Version 2013v1
Parts lists
Winner 2004
035: CONTROLLER ASSY
Pos
1
2
3
4
5
Article number
162.00031.000
9003481
9003788
No spare part
1001295
9003089
No spare part
No spare part
Version 2013v1
Units
1
1
1
1
1
1
2
2
Description
Controller 110A (not programmed)
S-Drive controller 120A
S-Drive controller 140A
Label control panel s/n
Controller bracket (Solo)
Controller bracket (S-Drive)
Screw M5xP0.8x20L
Nut-inserts
61
Parts lists
Winner
2004
036: SEAT & SEAT FRAME
2
1
3
4
5
Pos
1
2
3
4
5
-
62
Article number
118.00221.000
1002861
1003383
118.00231.000
9000034
9000042
1366
9000932
9003907
Units
1
1
1
1
1
1
1
11
1
1
Description
Armrest, right
Master seat with armrests
Lumbar knob
Armrest, left
Seat frame with slider (right-side operation)
Seat fixation strip
Plastic cover for seat fixation strip
Seat post
Nylon bearing seat post
Version 2013v1
Parts lists
01-01-2012:
Version 2012v1
Page
15-19
Drawing
-
Position
-
Changes
Changed the driving programs
Changes
Changed drawing description and description article numbers 1002356,
1009685 and 1012904
Changed drawing description and description article numbers 9003239 and
1009686
14-03-2012:
Version 2012v2
Page
54
Drawing
28
Position
1
55
29
1
01-01-2013:
Version 2013.v1
Page
56
62
Drawing
30
36
Version 2013v1
Position
-
Changes
Added article number 9002752
Changed article number 9000933 into 9003907
63
Parts lists
64
Version 2013v1