Download SERVICE MANUAL

DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
RMT-831
SERVICE MANUAL
LEVEL
2
US Model
Ver 1.0 2003. 12
DCR-TRV360/TRV460
Canadian Model
Revision History
DCR-TRV460
AEP Model
UK Model
East European Model
North European Model
Australian Model
How to use
Acrobat Reader
DCR-TRV460E
E Model
DCR-TRV361/TRV460/TRV460E/TRV461E
M2000/M2200 MECHANISM
Photo: DCR-TRV460
Link
SPECIFICATIONS
BLOCK DIAGRAMS
PRINTED WIRING BOARDS
SERVICE NOTE
FRAME SCHEMATIC DIAGRAMS
REPAIR PARTS LIST
DISASSEMBLY
SCHEMATIC DIAGRAMS
• For ADJUSTMENTS (SECTION 6), refer to SERVICE MANUAL, ADJ (987629351.pdf).
• For INSTRUCTION MANUAL, refer to SERVICE MANUAL, LEVEL1 (987629341.pdf).
• For MECHANISM ADJUSTMENTS, refer to the “8mm Video MECHANICAL ADJUSTMENT MANUAL IX
M2000 MECHANISM ” (9-929-861-11).
• Reference No. search on printed wiring boards is available.
• Table for differences of function of each model.
• TO TAKE OUT A CASSETTE WHEN NOT EJECT (FORCE EJECT)
• HELP: Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown.
On the VC-345 board
This service manual provides the information that is premised the circuit board replacement service and not intended repair
inside the VC-345 board.
Therefore, schematic diagrams, printed wiring boards, mounted parts location and electrical parts list of the VC-345 board are
not shown.
The following pages are not shown.
Schematic diagrams ........................... Pages 4-9 to 4-44
Mounted parts location .................. Pages 4-69 and 4-70
Printed wiring boards .......................... Pages 4-59 to 4-62 Electrical parts list ......................... Pages 5-16 to 5-24
DIGITAL VIDEO CAMERA RECORDER
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
TM
SERIES
SPECIFICATIONS
Video camera recorder
System
Video recording system
2 rotary heads, Helical scanning system
Still image recording system
Exif Ver. 2.2*1
*1 Exif is a file format for still images,
established by the JEITA (Japan
Electronics and Information Technology
Industries Association). Files in this format
can have additional information such as
your camcorder s setting information at the
time of recording.
Audio recording system
Rotary heads, PCM system
Quantization: 12 bits (Fs 32 kHz, stereo 1,
stereo 2), 16 bits (Fs 48 kHz, stereo)
Video signal
DCR-TRV360/TRV361/TRV460:
NTSC color, EIA standards
DCR-TRV460E/TRV461E:
PAL color, CCIR standards
Usable cassette
8 mm video format cassette
Tape speed
DCR-TRV360/TRV361/TRV460:
SP: Approx. 28.67 mm/s
LP: Approx. 19.11 mm/s
DCR-TRV460E/TRV461E:
SP: Approx. 28.70 mm/s
LP: Approx. 19.13 mm/s
Recording/play back time
DCR-TRV360/TRV361/TRV460:
(using 120 min. Hi8/Digital8 video cassette)
DCR-TRV460E/TRV461E:
(using 90 min. Hi8/Digital8 video cassette)
SP: 60 min
LP: 90 min
Fast forward/rewind time
DCR-TRV360/TRV361/TRV460:
(using 120 min. Hi8/Digital8 video cassette)
DCR-TRV460E/TRV461E:
(using 90 min. Hi8/Digital8 video cassette)
Approx. 5 min
Viewfinder
Electric viewfinder (monochrome)
Image device
3.0 mm (1/6 type) CCD (Charge Coupled
Device)
DCR-TRV360/TRV361/TRV460:
Gross: Approx. 460 000 pixels
Effective (still): Approx. 290 000 pixels
Effective (movie): Approx. 290 000 pixels
DCR-TRV460E/TRV461E:
Gross: Approx. 540 000 pixels
Effective (still): Approx. 350 000 pixels
Effective (movie): Approx. 350 000 pixels
Lens
Combined power zoom lens
Filter diameter: 37 mm (1 7/16 in.)
20 × (Optical), 990 × (Digital)
F = 1.6 ~ 2.4
Focal length
2.5 - 50 mm (1/8 - 2 in.)
When converted to a 35 mm still camera
In CAMERA-TAPE:
42 - 840 mm (1 11/16 - 33 1/8 in.)
In CAMERA-MEMORY:
42 - 840 mm (1 11/16 - 33 1/8 in.)
Color temperature
Auto
Minimum illumination
4 lx (lux) (F 1.6)
0 lx (lux) (during the NightShot plus
function)*2
*2 Objects unable to be seen due to the dark can
be shot with infrared lighting.
Input/Output connectors
S video input/output
Luminance signal: 1 Vp-p, 75 Ω (ohms),
unbalanced
Chrominance signal:
DCR-TRV360/TRV361/TRV460: 0.286 Vp-p
DCR-TRV460E/TRV461E: 0.3 Vp-p
75 Ω (ohms), unbalanced
4-pin mini DIN
Audio/Video input/output
AV MINIJACK
Video signal: 1 Vp-p, 75 Ω (ohms),
unbalanced, sync negative
Audio signal: 327 mV (at output impedance
more than 47 kΩ (kilohms)), Input impedance
more than 47 kΩ (kilohms), Output impedance
with less than 2.2 kΩ (kilohms)
Stereo minijack (φ 3.5mm)
DV input/output
4-pin connector
USB jack
mini-B
LCD screen
Picture
6.2 cm (2.5 type)
Total dot number
123 200 (560 × 220)
General
Power requirements
DC 7.2 V (battery pack)
DC 8.4 V (AC Adaptor)
Average power consumption (when using the
battery pack)
During camera recording using the viewfinder
2.9 W
During camera recording using the LCD
3.8 W
Operating temperature
0° C to 40° C (32° F to 104° F)
Storage temperature
-20° C to + 60° C (-4° F to + 140° F)
Dimensions (approx.)
85 × 98 × 151 mm (3 3/8 × 3 7/8 × 6 in.)
(w/h/d)
Mass (Approx.)
800 g (1 lb 12 oz) main unit only
940 g (2 lb 1 oz) including the NP-FM30
rechargeable battery pack, Hi8/Digital8
cassette, lens cap, and shoulder strap.
—2—
Supplied accessories
Memory Stick 8MB (1)
(DCR-TRV361/TRV461E)
AC Adaptor (1)
Power cord (1)
Lens cap (1)
Shoulder strap (1)
Wireless Remote commander RMT-831 (1)
A/V connecting cable (1)
USB cable (1)
Rechargeable battery pack NP-FM30 (1)
CD-ROM SPVD-012 USB Driver (1)
21-pin adaptor (1)
(AEP, UK, EE)
Camera Operations Guide (1)
Computer Applications Guide (1)
See page 7.
AC Adaptor AC-L15A/L15B
Power requirements
AC 100 - 240 V, 50/60 Hz
Current consumption
0.35 - 0.18 A
Power consumption
18 W
Output voltage
DC 8.4 V, 1.5 A
Operating temperature
0° C to 40° C (32° F to 104° F)
Storage temperature
-20° C to + 60° C (-4° F to + 140° F)
Dimensions (approx.)
56 × 31 × 100 mm (2 1/4 × 1 1/4 × 4 in.) (w/h/
d) excluding the projecting parts
Mass (approx.)
190 g (6.7 oz) excluding the power cord
Rechargeable battery pack (NP-FM30)
Maximum output voltage
DC 8.4 V
Output voltage
DC 7.2 V
Capacity
5.0 Wh (700 mAh)
Dimensions (approx.)
38.2 × 20.5 × 55.6 mm
(1 9/16 × 1 3/16 × 2 1/4 in.) (w/h/d)
Mass (approx.)
65 g (2.3 oz)
Operating temperature
0° C to 40° C (32° F to 104° F)
Type
Lithium ion
Design and specifications are subject to change
without notice.
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
Table for differences of function
Model
DCR-TRV360
DCR-TRV361
DCR-TRV460
US
E
US, CND, E
Color system
Playback system
NTSC
Digital8
NTSC
Digital8
Mechanism deck
M2200
M2200
Destination
• Abbreviation
AUS : Australian model
CND : Canadian model
DCR-TRV460E
AEP, UK, EE
NE, E, AUS
DCR-TRV461E
NTSC
Hi8/8/Digital8
PAL
Hi8/8/Digital8
PAL
Hi8/8/Digital8
M2000
M2000
M2000
E
EE : East European model
NE : North European model
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
1.
2.
3.
4.
5.
6.
Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes
and bridges.
Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
Look for parts which, through functioning, show obvious signs
of deterioration. Point them out to the customer and
recommend their replacement.
Check the B+ voltage to see it is at the values specified.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
Unleaded solder
Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
—3—
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
TABLE OF CONTENTS
Section
1.
Title
Page
SERVICE NOTE
Section
5.
1-1. Note for Repair ································································ 1-1
1-2. Power Supply During Repairs ········································· 1-1
1-3. To Take Out a Cassette when not Eject (Force Eject) ····· 1-2
1-4. Self-diagnosis Function ··················································· 1-3
1-4-1. Self-diagnosis Function ··················································· 1-3
1-4-2. Self-diagnosis Display ····················································· 1-3
1-4-3. Self-diagnosis Code Table ··············································· 1-4
2.
DISASSEMBLY
2-1.
2-2.
2-3.
2-4.
2-5.
Flow Chart ······································································· 2-1
Mechanism Deck Service Position ·································· 2-3
LCD Service Position ······················································ 2-5
Circuit Boards Location ·················································· 2-6
Flexible Boards Location ················································ 2-7
3.
BLOCK DIAGRAMS
3-1.
3-2.
3-3.
3-4.
3-5.
3-6.
3-7.
3-8.
3-9.
Overall Block Diagram (1/6) ··········································· 3-1
Overall Block Diagram (2/6) ··········································· 3-3
Overall Block Diagram (3/6) ··········································· 3-5
Overall Block Diagram (4/6) ··········································· 3-7
Overall Block Diagram (5/6) ··········································· 3-9
Overall Block Diagram (6/6) ········································· 3-11
Power Block Diagram (1/3) ··········································· 3-13
Power Block Diagram (2/3) ··········································· 3-15
Power Block Diagram (3/3) ··········································· 3-17
4.
PRINTED WIRING BOARDS AND
SCHEMATIC DIAGRAMS
Title
Page
REPAIR PARTS LIST
5-1.
Exploded Views ···························································· 5-2
5-1-1. Overall Assembly ·························································· 5-2
5-1-2. Front Panel Block ························································· 5-3
5-1-3. Lens Block ···································································· 5-4
5-1-4. LCD Block ···································································· 5-5
5-1-5. Cabinet R Block ···························································· 5-6
5-1-6. EVF Block ···································································· 5-7
5-1-7. Battery Panel Block ······················································ 5-8
5-1-8. MD Frame Block ·························································· 5-9
5-1-9. Cassette Compartment Assembly, Drum Assembly ··· 5-10
5-1-10. LS Chassis Block Assembly ······································· 5-11
5-1-11. Mechanical Chassis Block Assembly-1 ······················ 5-12
5-1-12. Mechanical Chassis Block Assembly-2 ······················ 5-13
5-2.
Electrical Parts List ····················································· 5-14
4-1. Frame Schematic Diagrams ············································· 4-1
4-2. Schematic Diagrams ························································ 4-5
CD-472 (CCD IMAGER) ················································ 4-7
PD-205 (LCD DRIVER, BACKLIGHT DRIVE) ········· 4-45
SI-041 (STEADYSHOT, JACK) ··································· 4-47
FP-792 FLEXIBLE ······················································· 4-47
FP-228, FP-299, FP-300, FP-301, FP-302, FP-802
FLEXIBLE ···································································· 4-49
SS-5100, PR-5100 (CONTROL KEY BLOCK) ··········· 4-50
CF-5100 (CONTROL KEY BLOCK) ··························· 4-51
4-3. Printed Wiring Boards ··················································· 4-55
CD-472 ·········································································· 4-57
PD-205 ··········································································· 4-63
SI-041, FP-792 FLEXIBLE ·········································· 4-65
FP-228, FP-299, FP-300, FP-301, FP-302, FP-802
FLEXIBLE ···································································· 4-67
4-5. Mounted Parts Location ················································ 4-71
—4—
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
SECTION 1
SERVICE NOTE
1-1. NOTE FOR REPAIR
Make sure that the flat cable and flexible board are not cracked of
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
When remove a connector, don’t pull at wire of connector.
It is possible that a wire is snapped.
When installing a connector, don’t press down at wire of connector.
It is possible that a wire is snapped.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
1-2. POWER SUPPLY DURING REPAIRS
In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4V), the power is shut off so
that the unit cannot operate.
The following method is available to prevent this.
Method 1.
Use the AC power adaptor (AC-L10, AC-VQ800 etc.).
1-1
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
1-3. TO TAKE OUT A CASSETTE WHEN NOT EJECT (FORCE EJECT)
1 Refer to “SECTION 2 DISASSEMBLY” to remove the mechanism deck block.
2 Disconnect CN2401 (2P) of VC-345 board.
3 Add +5V from the DC POWER SUPPLY and unload with a pressing the cassette compartment.
4 Pull the timing belt in the direction of
arrow A with a pincette while pressing
the cassette compartment (take care
not to damage) to adjust the bending
of a tape.
Press the cassette compartment not to
rise the cassette compartment
Pincette
A
[DC power supply]
(+5V)
Timing belt
5 Let go your hold the cassette
compartment and rise the cassette
compartment to take out a cassette.
A
Loading motor
Disconnect CN2401
of VC-345 board.
Adjust the bending of a tape
Timing belt
1-2
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
1-4. SELF-DIAGNOSIS FUNCTION
1-4-1. Self-diagnosis Function
1-4-2. Self-diagnosis Display
When problems occur while the unit is operating, the self-diagnosis
function starts working, and displays on the viewfinder or LCD what
to do. This function consists of two display; self-diagnosis display
and service mode display.
Details of the self-diagnosis functions are provided in the Instruction
manual.
When problems occur while the unit is operating, the counter of the
viewfinder or LCD shows a 4-digit display consisting of an alphabet
and numbers, which blinks at 3.2 Hz. This 5-character display
indicates the “repaired by:”, “block” in which the problem occurred,
and “detailed code” of the problem.
Viewfinder
Display window
C : 3 1 : 11
C:31:11
Blinks at 3.2Hz
C
Repaired by:
C : Corrected by customer
H : Corrected by dealer
E : Corrected by service
engineer
31
Block
11
Detailed Code
Refer to 1-4-3. Self-diagnosis Code Table .
Indicates the appropriate
step to be taken.
E.g.
31 ....Reload the tape.
32 ....Turn on power again.
1-3
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
1-4-3. Self-diagnosis Code Table
Repaired by:
Self-diagnosis Code
Block
Function
Detailed
Code
Symptom/State
C
C
C
0
2
2
4
1
2
0
0
0
0
0
0
C
3
1
1
0
C
3
1
1
1
C
C
C
C
C
C
C
C
C
C
C
3
3
3
3
3
3
3
3
3
3
3
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
3
3
4
4
4
4
4
0
1
2
3
0
1
0
1
2
3
4
C
3
2
1
0
C
3
2
1
1
C
3
2
2
0
C
3
2
2
1
C
3
2
2
2
T reel fault.
C
3
2
2
3
S reel fault.
C
3
2
3
0
FG fault when starting capstan.
C
3
2
3
1
FG fault during normal capstan
operations.
C
3
2
4
0
FG fault when starting drum.
C
3
2
4
1
PG fault when starting drum.
C
3
2
4
2
C
3
2
4
3
C
3
2
4
4
Correction
Non-standard battery is used.
Condensation.
Video head is dirty.
LOAD direction. Loading does not
complete within specified time
UNLOAD direction. Loading does not
complete within specified time
T reel side tape slacking when unloading.
S reel side tape slacking when unloading.
T reel fault.
S reel fault.
FG fault when starting capstan.
FG fault during normal capstan operations.
FG fault when starting drum.
PG fault when starting drum.
FG fault during normal drum operations.
PG fault during normal drum operations.
Phase fault during normal drum operations.
LOAD direction loading motor timeout.
UNLOAD direction loading motor
time-out.
T reel side tape slacking when
unloading.
S reel side tape slacking when
unloading.
FG fault during normal drum
operations.
PG fault during normal drum
operations.
Phase fault during normal drum
operations.
1-4
Use the InfoLITHIUM battery.
Remove the cassette, and insert it again after one hour.
Clean with the optional cleaning cassette.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Load the tape again, and perform operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
Remove the battery or power cable, connect, and perform
operations from the beginning.
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
Repaired by:
Self-diagnosis Code
Block
Function
Detailed
Code
Symptom/State
E
6
1
0
0
Difficult to adjust focus
(Cannot initialize focus.)
E
6
1
1
0
Zoom operations fault
(Cannot initialize zoom lens.)
E
6
2
0
0
E
6
2
0
1
Correction
Inspect the lens block focus reset sensor (Pin qs of CN1551 of
VC-345 board) when focusing is performed when the control dial
is rotated in the focus manual mode and the focus motor drive circuit
(IC1554 of VC-345 board) when the focusing is not performed.
Inspect the lens block zoom reset sensor (Pin qg of CN1551 of
VC-345 board) when zooming is performed when the zoom switch
is operated and the zoom motor drive circuit (IC1554 of VC345board) when zooming is not performed.
Steadyshot function does not work well.
(With pitch angular velocity sensor output
stopped.)
Steadyshot function does not work well.
(With yaw angular velocity sensor output
stopped.)
1-5
Inspect pitch angular velocity sensor (SE752 of SI-041 board)
peripheral circuits.
Inspect yaw angular velocity sensor (SE751 of SI-041 board)
peripheral circuits.
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
“1-5. CHANGE OF IC4501” is not shown.
Pages 1-6 is not shown.
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
SECTION 2
DISASSEMBLY
HELP
2-1. FLOW CHART
Note: When you remove Cabinet (R) Block,
or when you assembly, please slide
NS knob to the position of "ON".
The following flow chart shows the disassembly procedure.
1
2
NS knob
8
1
3
2
7
2
1
6
5
9
9 q;
5
6
5
7
qd
qf
1
4
3
4
4
8
4
3
1
2
3
4
5
Lock ace x3
Cabi (upper)
Grip belt
Lock ace x3
Cabi (L)
1
6 Lock ace x3
7 Claw
8 Front panel
Note: Flexible board is connected.
9 FP-796: CN754, CN1001
1
2
3
4
5
6
Lock ace x6
NS knob to the position of "ON".
Cabi (R)
VC-345: CN1007
VC-345: CN1003
VC-345: CN1008
1
2
3
4
5
6
7
8
Tripod Screw
Tapping P2 x2
Tapping P2 x6
Claw
CF-5100
Tapping P2 x4
Claw x2
P Cabi (C)
9
q;
qa
qs
qd
qf
qg
qh
Tapping P2 x2
Tapping P2 x1
P Cabi (M)
PD-205: CN6005
PD-205: CN6001
PD-205, LCD901, ND901
Tapping P2 x4
Hinge assy
4
8
5
3
4
7
8
3
6
1
6
7
6
2
Lift up the EVF.
Tapping P2 x4
Down the EVF.
EVF block
4
3
2
1
2
3
4
2
5
6
7
8
6
9
5
1
qs
qh
6
4
qa
HELP qg
1
2
3
4
5
EVF Cabi (upper)
EVF Cabi (lower)
FP-797: LCD902
EVF lens
VC-345: CN1013
VC-345: CN1016
VC-345: CN4001
Lock ace x3
EVF/Battely panel block
2
6
7
8
9
1
2
5
VC-345: CN1009
Tapping P2 x1
Lock ace x1
SS-5100
1 VC-345: CN1501 4 Lock ace x2
2 VC-345: CN1551 5 Boss
6 Lens LSV-820A
3 Lens sheet
2
3
7
3
1
2
8
4
5
1
1 Tapping P2 x4
2 Claw x2
3 P Cabi (C)
2-1
1
2
3
4
6
VF blind sheet
VC-345: CN2403, CN2404, CN3201
VC-345: CN2401
Screw (M1.7) x2
5
6
7
8
1
Claw
Open the VC-345.
VC-345: CN2402
VC-345
1 Screw (M1.7) x3
2 CS frame
2-2
1
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
2-2. MECHANISM DECK SERVICE POSITION
Connection to Check the Mechanism deck
To check the mechanism deck, set the Camera or VTR to the "Forced power ON" mode. (Or, connect the control key
block (SS-5100) to the CN1009 of VC-345 board and set the power switch to the "CAMERA" or "PLAY/edit" position.)
Operate the Camera functions of the zoom and focus, the VTR function using the adjustment remote commander
(with the HOLD switch set in the OFF position).
Setting the "Forced Camera Power ON" mode
Exiting the "Forced Power ON" mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: A, address: 10, set data: 02 and
press the PAUSE button of the adjustment remote
commander.
1) Select page: 0, address: 01, and set data: 01.
2) Select page: A, address: 10, data: 00, and press the PAUSE
button of the adjustment remote commander.
3) Select page: 0, address: 01, and set data: 00.
Setting the "Forced VTR Power ON" mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: A, address: 10, set data: 02 and
press the PAUSE button of the adjustment remote
commander.
1
2
1
How to move up the cassette
compartment manually
6
5
7
9
2
Press the cassette compartment
in the direction of the arrow A
to move it up in the direction of
the arrow B.
Mechanism deck
B
A
4
1
1
8
4
3
Lens block
6
3
2
Info lithium battery
(L series)
2
1
7
3
CPC jig connector
(J-6082-539-A)
1
6
5
Front panel block
1
Contacting
surface
8
4
VC-345 board
4
6
5
Adjustment remote
commander (RM-95)
I/F unit for LANC control
(J-6082-521-A)
4
9
8
3
5
Cabinet R block
Eject switch
4
EVF block/
Battery panel block assembly
6
6
1
7
1
2
5
2
3
4
2-3
AC IN
Control key block
(SS-5100)
AC adaptor
When exiting the "Forced Power ON" mode, connect the control
key block (SS-5100) to the CN1009 of VC-345 board. Or, when
ejecting the cassette, connect the control key block (SS-5100) to
the CN1009 of VC-345 board. and press the Eject switch.
2-4
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
2-3. LCD SERVICE POSITION
2
3
1
CPC jig connector
1
Conductor side
CN1011
16
LCD panel
Back light unit
PD-205 board
CPC jig connector
(J-6082-539-A)
L serices Info
LITHIUM battery (7.2Vdc)
AC adaptor
AC IN
AC adaptor
AC IN
LANC jack
Adjustment
remote commander (RM-95)
I/F unit for LANC control
(J-6082-521-A)
2-5
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
2-4. CIRCUIT BOARDS LOCATION
VC-345
CD-472
SI-041
PD-205
Board Name
Function
CD-472
VC-345
CCD IMAGER
A/D CONVERTER, TIMING GENERATOR, VIDEO/AUDIO DSP,
LENS CONTROL, LENS DRIVE, Hi8/Std8 VTR PROCESS, VIDEO IN/OUT ,
DV SIGNAL PROCESS, REC/PB AMP, DV INTERFACE, STEADYSHOT,
Hi8/Std8 PB AMP, USB/MODE CONTROL, MS INTERFACE, MEMORY,
HI CONTROL, CAMERA/MECHA CONTROL, SERVO, AUDIO, DC CONTROL,
CONNECTOR
LCD DRIVE, BACKLIGHT DRIVE
STEADYSHOT, JACK
PD-205
SI-041
2-6
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
2-5. FLEXIBLE BOARDS LOCATION
SS-5100
FP-797
FFC-005
FP-799
CF-5100
FP-792
FP-796
PR-5100
2-7E
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
HELP
Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown.
Harness (PD-124)
Claw
Claw
Insulating sheet (CF)
Tape (CF)
(TRV360/TRV460/TRV460:E/TRV461E)
Note: Close the LCD panel, when you work.
HELP
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
3. BLOCK DIAGRAMS
Link
OVERALL BLOCK DIAGRAM (1/6)
OVERALL BLOCK DIAGRAM (6/6)
OVERALL BLOCK DIAGRAM (2/6)
POWER BLOCK DIAGRAM (1/3)
OVERALL BLOCK DIAGRAM (3/6)
POWER BLOCK DIAGRAM (2/3)
OVERALL BLOCK DIAGRAM (4/6)
POWER BLOCK DIAGRAM (3/3)
OVERALL BLOCK DIAGRAM (5/6)
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
SECTION 3
BLOCK DIAGRAMS
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
CD-472 BOARD
LENS BLOCK
VC-345 BOARD (1/6)
Q951
IRIS
ZOOM MOTOR
FOCUS MOTOR
M
NIGHT
SHOT
PLUS
LENS
TEMP
SENSOR
IRIS
METER
M
ZOOM
SENSOR
IC951
CCD
IMAGER
CN1501
1
1 – 4 12 – 14
M
FOCUS
SENSOR
CN951
BUFFER
7
V1 – V4,RG,H1,H2
H
Hi8/Std8
7
ı
9
11
ı
14
IC 3701 Y OUT
8
ı
6
5 7 17 19
LENS TEMP AD
ZM RST
FC RST
ZOOM
MOTOR
DRIVE
XNS SW
22 23
13 – 16
EN1, DIR1A,
DIR1B
20
1 2
IRIS
BIAS(–)
HALL GAIN
CONTROL
FOCUS
MOTOR
DRIVE
9 – 12
5
HALL
BIAS
HALL
AMP
IC1552
(4/18)
25
26
28
31
V1 – V4
19
IRIS
DRIVE(–)
4
5
Q1551
14
8
HALL
GAIN
IRIS
DRIVE
TIMING
GENERATOR
(1/18)
3
ADCK
VCK
2
XRST VTR
43
20
R1510
1
OVERALL (3/6)
(PAGE 3-5)
OVERALL (4/6)
(PAGE 3-7)
16
AD0 –AD9
CLPOB
VCK
R1507 TRV360/TRV361
TG HD, TG VD
ZSG1, ZV1, TG ID
VGAT
CAM DD ON
3
OVERALL (2/6)
(PAGE 3-3)
EN0,EN1, DIR0A,B, DIR1A,B,
FC RST, ZM RST
42
CH CS, CH SO, CH SCK
35
37
ı
39
47
EN0, DIR0A, HALL
REF
DIR0B
40
ADCK
9
VCK
12
44
45
ZSG1
34
ZV1
41
TG ID
48
VGAT
36
Hi8/Std8
AD0 – AD9
2
ı
11
IC1502
TRV460/TRV460E
/TRV461E
XRST VTR
IC1501
PB C RF
S/H, AGC,
A/D CONVERTER
(1/18)
46 47 48
X1501
27 MHz
IRIS
DRIVE
Q1554
2 4 21 23
IC1554
(4/18)
21
IRIS BIAS(+)
IRIS HALL(+)
ZOOM A,B,XA,XB
1–4
IRIS HALL(–)
10 – 7
FOCUS A,B,XA,XB
15 12
ZM SENS OUT
FC SENS OUT
17
TEMP
IR SWITCH
5
1
CLPDM, PBLK, 19
2 XSHP, XSHD 21
ı
15
23
16
18
21
22
RG, H1, H2
1
ı
4
CN1551
36
30
34
CCD OUT
14
CH CS, CH SO, CH SCK
3-1. OVERALL BLOCK DIAGRAM (1/6)
3. BLOCK DIAGRAMS
6 7
12
10
HALL
GAIN
HALL
OFFSET
CAM SI, CAM SO, CAM SCK, CAM CS
CK CONT
HALL AD
HALL AD, LENS DET,
LENS TEMP AD, XNS SW
IRIS PWM
IRIS PWM
PITCH AD, YAW AD
SDC IN
XVIDEO IN
XCS IC 3701
SI-041 BOARD (1/4)
SE752
PITCH SENSOR
SE751
YAW SENSOR
CN754 (1/4)
LIA 1 30
LIA 2
29
CN1001
(1/4)
7
8
8
12
IC2001
2
STEADYSHOT
(9/18)
18
PITCH AD
VD SO, VD SCK
LINE Y ON
YAW AD
VSP SI, VSP SO, XVSP SCK
4
OVERALL (4/6)
(PAGE 3-7)
XCS AU1
INT MIC L,R
MIC901
MICROPHONE
L
CN753
INT MIC L
INT MIC R
1
33
32
IC5801
2 MIC AMP
19 (16/18)
IC5402
MIC L,R
9
12
20 – 22 23
4
5
AUDIO L,R I/O
3
XCS IC 3701
Q3701
DC LEVEL
DETECTOR
Q5401, 5402
MUTE
3
64
7
8
57
58
59
SP+,–
11
4 REC OUT L, R
5
9 10
49
51
46
XS JACK IN
13
11
12
S Y I/O
S C I/O
24
26
39
IC3701
48
42 VIDEO IN/OUT
(6/18)
XS JACK IN
25
Q3702, 3703
VIDEO I/O
AUDIO L I/O
J752
A/V
AUDIO R I/O
AV JACK IN
15
22
18
19
17
19
20
18
VIDEO I/O
AV JACK IN
MUTE
AUDIO
PROCESS
(16/18)
Q8504
14
36
18
22
IC 3701
Y OUT
VIDEO
BUFFER
34
46
7
44
5
1
47
IC8501
5
15
A/D
ı
CONVERTER 24
(3/18)
14
1
2
6
OVERALL (3/6)
(PAGE 3-5)
Hi8/Std8, LINE
AD0 C – AD9 C
IC 3701 C OUT
ADCK27
IC 8001 Y OUT
IC 8001 C OUT
IC 8001 Y OUT
IC 8001 C OUT
Hi8/Std8
Hi8/Std8
IC 2201 Y OUT
IC 2201 C OUT
ACC-CONT
AGC-CONT
BEEP
AV JACK IN, XS JACK IN
9
OVERALL (2/6)
(PAGE 3-4)
10
OVERALL (2/6)
(PAGE 3-3)
SP+, –
ACC-CONT, AGC-CONT, CLPVO
05
3-1
AU BPF
BPF MONI
FRQ TUNE
HALL OFFSET, HALL GAIN, HALL REF
CN1008
SP901
SPEAKER
1.7M DEV, 1.5M DEV
Hi8/Std8, LINE
IC 2201 Y OUT
IC 2201 C OUT
5
OVERALL (2/6)
(PAGE 3-3)
PB RF
AFM FSC
RF SWP
17
18
28
29
CONTROL KEY BLOCK (CF-5100) (1/2)
A : VIDEO SIGNAL
A : AUDIO SIGNAL
DATA TO SFD
DATA FROM SFD
SFD BCK
SFD LRCK
SFD FCK
KASYAON
8
9
12
10
11
Hi8/Std8
26
14
24
1
CPLVO
S Y I/O
S C I/O
J751
S VIDEO
PB IN L, R
AUDIO
A/D, D/A
2
3 CONVERTER
(16/18)
15
16
IC5401
VD SO, VD SCK
R
2
63
DEM 0, 1,
XPWAD, XPWDA
6
7
13
14
3-2
7
OVERALL (2/6)
(PAGE 3-3)
8
OVERALL (3/6)
(PAGE 3-5)
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
3. BLOCK DIAGRAMS
3-2. OVERALL BLOCK DIAGRAM (2/6)
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
VC-345 BOARD (2/6)
SPCK
224
ı
231
233
234
AD0 – AD9
CLPOB
VCK
221
241
TG HD, TG VD
ZSG1, ZV1, TG ID
OVERALL (1/6)
(PAGE 3-2)
3
ZSG1
ZV1
TG ID
CAM DD ON
VGAT
EN0,1, DIR0A,B, DIR1A,B
EN0,1
219
220
Hi8/Std8, LINE
AD0 C – AD9 C
OVERALL (1/6)
(PAGE 3-2)
7
IC 3701 C OUT
ADCK27
Hi8/Std8, LINE
IC 8001 Y OUT
IC 8001 C OUT
IC8001
VIDEO/AUDIO DSP,
D/A CONVERTER,
LENS CONTROL
(2/18)
5
279
ı
282
239
248
OVERALL (5/6)
(PAGE 3-9)
13
14
RYO0 – RYO3
RCO0 – RCO3
70 71
121 122
47
48
41
HYO, HCO
ADATAIN0,1
RYI0 – RYI3
13 14
72 73
272
273
275
276
RCI0 – RCI3
123 – 125
166
284
285
HYI, HCI
12
75
237
238
298
299
ADATAOUT0,1
126
167
DSCK VM
252
ı
261
33
245
XSYS RST
SFD BCK
SFD LRCK
86
168
169
154 156
158 159
149
157
OVERALL (6/6)
(PAGE 3-11)
15
PANEL R
PANEL G
PANEL B
10
LCKO
TRCKO
LBUS0-3
54 55 57
107 109 110
152 – 155
189 190 192
3
114
157
15
58
59
111
112
62
21
78
79
47
42
ı
45
27
CN1001
(2/4)
6
IC8301
ı
9
DV INTERFACE
(9/18)
24 – 26
29 – 32
34 – 37
TPA+, –, TPB+, –
28
29
31
32
9
8
6
5
35
34
2
3
36
1
CN754
(2/4)
CN751
24
119
40
39
45
171 174
176 – 185
92
93
196
190
66
64
62
XCS IC 8301
XCS IC 6001
XCS IC 8301
XCS IC 6001
VSP SI, VSP SO, XVSP SCK
VSP SI, VSP SO, XVSP SCK
CAM SI, CAM SO. CAM SCK. CAM CS
FRRV, TRRV, TRRT, DRP
17
OVERALL (4/6)
(PAGE 3-7)
HI SI, HI SO. XHI SCK. XCS MECHA
60
FRRV, TRRV, TRRT, DRP
SWP
USB 3.1V
Q1007
USB
PULL UP
CAM SI, CAM SO. CAM SCK. CAM CS
XCS IC8001
SYS V
XCS IC 8001
SYS V
USB D+, USB D–
USB D+, USB D–
SYS V
HI SI, HI SO. XHI SCK. XCS MECHA
USB CLK
DSCK VM
USB CLK
DSCK VM
D0 VM – D15 VM
A1 VM – A22 VM
MDQ0 T – MDQ15 T
MA0 T – MA10 T, MA12 T
MEMCK OUT
MXCSO
19 – 24
27 – 32
35
18
IC8002
16M
SDRAM
(3/18)
DSCK VM
D0 VM – D15 VM
A1 VM – A11 VM, A13 VM
19 – 24
27 – 32
D0 VM – D15 VM
29 – 36
38 – 45
1 – 10 13
16 – 25
48
IC5702
EEPROM
(11/18)
IC5501
16M
SDRAM
(12/18)
18
IC5502
32M
FLASH
(12/18)
26
12
221
168
97
ı
99
237
177
122
IC5701
USB CONTROL,
MEMORY STICK
INTERFACE,
MODE CONTROL
(11/18)
XCS EEP,
EEP XRDY,
EEP RXD3,
EEP SCK3.
EEP TXD3
35
2356
8 9 11
12 39 40
42 43 45
46 48 49
185
186
1 – 4 7 – 12
291 – 298
301 – 304
A1 VM – A19 VM
2356
8 9 11
12 39 40
42 43 45
46 48 49
234
16 – 18
21 – 24
27 – 35
D0 VM – D15 VM
A1 VM – A22 VM
1–3
56
XCS SDRAM VM
XCS FLASH
XSYS RST
256
CN752
USB D+ PULL UP
CN1015
2
5
1
6
7
71
145
144
140
139
69
93
ı
96
253
238
239
2
4
6
MS DIO, MS BS, MS SCLK
MS XIN
FOR JIG
MS XIN
MEMORY
STICK
5
MS LED ON
KEY AD 6
KEY AD 5
KEY AD 1
KEY AD 0
KEY AD 0, 1, 5. 6
MS LED ON
18
IC 5001 RXD0, IC 5001 TXD0, IC 5001 SCK0, IC 5001 CS
OSD V
XDS RESET
XVM MAD
MELODY
Q5701, 5702
MODURATOR
MELODY ENV
AV JACK IN
XS JACK IN
OVERALL (5/6)
(PAGE 3-9)
BEEP
9
AV JACK IN, XS JACK IN
IR ON
254
OVERALL (1/6)
(PAGE 3-2)
19
OVERALL (5/6)
(PAGE 3-10)
250
05
3-3
MS LED ON
MS XIN
CN1016
287
124
131
137
249
138
1
USB DET
220
86
274
SFD LRCK
CAM DD ON
TP X
TP SEL1
TP Y
TP SELECT SWITCH
TP
SEL2
Q5703
(USB)
VCC
USB D+, USB D–
78
81
85
80
235 236
103 – 105
2
3
D+, –
MS DIO, MS BS, MS SCLK
230
A : VIDEO SIGNAL
A : AUDIO SIGNAL
A : VIDEO/AUDIO SIGNAL
A : VIDEO/AUDIO/SERVO SIGNAL
DV
D24A00 – D31A07, DXXA08, DXXA09, ALE, WRX, RDX
REC PROOF
98
ı
116
198 – 205
207 208
210 – 215
1
ı
4
TPA, NTPA, TPB, NTPB
D24A00 – D31A07, ALE, WRX, RDX
D24A00 – D31A07, DXXA08, DXXA09, ALE, WRX, RDX
188
158
OVERALL (3/6)
(PAGE 3-5)
RF IN
X5703
48 MHz
Q8001
ACC-CONT, AGC-CONT,
CLPVO
RF IN
IC5703
XTAL OSC
(11/18)
95
96
PANEL HD, PANEL VD
TPX, TPY, TP SELE1
OVERALL (1/6)
(PAGE 3-2)
IC6001
104
DV SIGNAL
PROCESS
149
150
(7/18)
186 187
16
RECCK
D755
46
BUFFER
RECCK
SI-041 BOARD (2/4)
VSP SI, VSP SO, XVSP SCK
121 122
124 – 137
EVF HD, EVF VD
RECA1,2
REC PROOF
141
EVF G/BW Y
RECDT
RECA1,2
139
80
160
161
162
163
164
165
LINEOUT V
XSYS RST
RECDT
FRRV, TRRV, TRRT
150
ı
152
82
83
85
91
USB XEN
VFI OE
ALIGN VD
BIRDS VD
BIRDS FLD
LINEOUT V
VREF
127
168
DIR1A,B 250
251
87
89
SFD BCK
SFD LRCK
SFD FCK
KASYAON
164
165
264
ı
267
28
29
OVERALL (4/6)
(PAGE 3-8)
45
119 120
162 163
287
288
301
302
216
217
236
222
143
53
60
DATA TO SFD
DATA FROM SFD
OVERALL (1/6)
(PAGE 3-2)
VCK
268
ı
271
DIR0A,B 246
247
FC RST, ZM RST
LCKO
USB D+
12
20
XCS IC 8301
OVERALL (4/6)
(PAGE 3-7)
139
DATA BUS
11
SPCK
ADDRESS BUS
OVERALL (3/6)
(PAGE 3-5)
3-4
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
3. BLOCK DIAGRAMS
3-3. OVERALL BLOCK DIAGRAM (3/6)
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
M2000/M2200
MECHA DECK (1/2)
VC-345 BOARD (3/6)
M2000: TRV460/TRV460E/TRV461E
M2200: TRV360/TRV361
VIDEO HEAD
ODD
16
OVERALL (2/6)
(PAGE 3-4)
RECDT
RECDT
RECA1,2
RECA1,2
RECCK
RECCK
RF IN
RF IN
DV PB RF
RF MON
TRV460/TRV460E/TRV461E
1
OVERALL (1/6)
(PAGE 3-2)
Hi8/Std8
Hi8/Std8
187
ı
196
185
198
AD0 – AD9
ADCK
VCK
8
OVERALL (1/6)
(PAGE 3-2)
IC 2201 Y OUT
IC 2201 C OUT
Hi8/Std8
Hi8/Std8
4
213
VCO
JOG VD
X1/2 SWP
SWP DIR
ATF SAMPLE
SYS V
RF AGC OUT
PB C RF
PB RF
51
49
77
DOP
REC Y/MT CONT
REC L CONT
RP IR
DOC DET
MT FO
MT Q
MECHA HD, MECHA VD
79
93
94
101
157
158
98
99
CK CONT
XTBC V RST
TBC VD
XCS IC 2201
XRST IC 2201
SPCK
66
9
11
14
7
53
83
84
85
87
88
35
25
30
IC3201
REC/PB AMP
(8/18)
3
4
ODD (SP1)
10
9
EVEN (SP2)
Q3206 – 3209
Hi8/Std8
PB ON SWITCH
22
36
34
13
37
43
EVEN
XME/MP
SW PS
ALL PS
3
48
8
12
15
19
IC3001
Hi8/Std8
PB AMP
(10/18)
18
XMP/ME
Q3001
10
46
13
AGC
CONTROL
FE (X)
ERASE HAED
OSC
11
AGC SLOW
RP POWER SAVE
RP PB MODE
Q3002
5
Q3202, 3204, 3205
BUFFER
RF ENV DET
AFM FSC
DRUM 8PB
XME/MP
SW PS
ALL PS
XFE ON
AFC F0 ADJ
67
CN1011 (1/3)
RF MON
9
SW DIR
5
PB RF
2
BPF MONI
3
DOP
RF SWP
5
20
16
15
23
CAM SO, CAM SCK
11
OVERALL (2/6)
(PAGE 3-3)
FREQ TUNE
AU BPF
1.7M DEV, 1.5M DEV
6
OVERALL (1/6)
(PAGE 3-2)
27
28
SPCK
HALL OFFSET, HALL GAIN, HALL REF
21
OVERALL (4/6)
(PAGE 3-8)
81
AGC SLOW
RP POWER SAVE
RP PB MODE
RF ENV DET
DA STRB
FLYING
ERASE
5
4
7
8
38
Q2207
AFC F0
20
IC2201
Hi8/Std8
VTR PROCESS
(5/18)
95
ı
97
VD SI, VD SO, VD SCK
OVERALL (4/6)
(PAGE 3-7)
PB FBDP
LPF FO
AGC EVR
40
42
44
CN3201
RF SWP
PB C RF
46
17
ı
19
22
10
IC1601
EVR
(D/A CONVERTER)
(10/18)
3
4
24
26
6
8
12
21
9
11
RF SWP
AFM FSC
PB RF
MT FO
MT Q
AFC F0 ADJ
REC Y/MT CONT
REC L CONT
RP IR
DOC DET
XMP/ME
PB FBDP
LPF FO
AGC EVR
A : VIDEO SIGNAL
A : AUDIO SIGNAL
A : SERVO SIGNAL
A : VIDEO/SERVO SIGNAL
A : VIDEO/AUDIO/SERVO SIGNAL
BPF MONI
05
3-5
3-6
CPC
(FOR CHECK)
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
3. BLOCK DIAGRAMS
3-4. OVERALL BLOCK DIAGRAM (4/6)
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
VC-345 BOARD (4/6)
OVERALL (2/6)
(PAGE 3-3)
12
SPCK
SPCK
35
38
36
34
OVERALL (1/6)
(PAGE 3-2)
2
VSP SO, VSP SI, XVSP SCK
VSP SO, XVSP SCK
XRST VTR
XRST VTR
CH CS, CH SO, CH SCK
VSP SI, VSP SO, XVSP SCK
62
73
71
CK CONT
HALL AD,
LENS TEMP AD, XNS SW
OVERALL (1/6)
(PAGE 3-2)
4
SERIAL
INTERFACE
IC2401 (1/3)
45 DRUM ERROR
LPF
43
41
Q2402
DRUM Hi8/Std8
MODE SWITCH
11
M2000: TRV460/TRV460E/TRV461E
M2200: TRV360/TRV361
(15/18)
44
CAP PWM
89
78
77
75
161
37
DRUM PWM
88
69
70
67
CAM SI, CAM SO, CAM SCK, CAM CS
XCS IC 2401
16
100
M2000/M2200
MECHA DECK (2/2)
IC2401 (3/3)
CAP ERROR
25
6
9
24
IC1301 (1/2)
DRUM/CAPSTAN 62
PWM DRIVE
61
(17/18)
IRIS PWM
PITCH AD, YAW AD
SDC IN
XVIDEO IN
XCS IC 3701
LINE Y ON
XCS AU1
DEM 0, 1, XPWAD, XPWDA
CAMERA/
MECHA
CONTROL
(14/18)
76
97
137
139
VD SO, VD SCK
190
119
106
ı
108
64
67
15
13
CAM SO, CAM SCK
AFC F0
JOG VD
X1/2 SWP
SWP DIR
ATF SAMPLE
SYS V
OVERALL (3/6)
(PAGE 3-5)
20
117
38
83
82
80
VSP SO, VSP SI, XVSP SCK
VD SI, VD SO, VD SCK
CAM SI, CAM SO, CAM SCK, CAM CS
31
EVF DD ON
XCS LCD
173
202
MECHA HD, MECHA VD
CK CONT
TBC V RST
TBC VD
XCS IC 2201
XRST IC 2201
AGC SLOW
RP POWER SAVE
RP PB MODE
RF ENV DET
RF SWP
DA STRB
DOP
188
205
154
132
214
26
196
115
172
59
194
DRUM 8PB
ALL PS
SW PS
XME/MP
XFE ON
FG AMP
53
PG AMP
50
FG
52
PG
49
OVERALL (3/6)
(PAGE 3-6)
CAP VS
CAP FWD, CAP ON
CAP FWD, CAP ON
CAP FG
CAP FG
75
77
1
80
CAPSTAN
MOTOR
DRIVE
4
FG AMP
74
76
78
CAP U, V, W
HU1, 2
HV1, 2
HW1,2
10
ı
15
FG1, 2
7
8
DEW AD
DEW AD
MODE SW A-C
MODE SW A – C
LOAD,
UNLOAD
LOAD,
UNLOAD
LM LIM DET
LM LIM DET
180
109
120
TAPE END
TAPE END
TAPE TOP
TAPE TOP
T REEL FG
T REEL FG
S REEL FG
S REEL FG
(15/18)
32
33
45 – 52 32 33
22 24 25
MC BUS 0 – 7, HA0, 1, ALE, WRX, RDX
XCS IC 8301
XCS IC 6001
XCS IC 8001
FRRV, TRRV, TRRT, DRP
SYS V
REC PROOF
TRRV
TRRT
FRRV
DRP
SWP
18
215
155
179
178
23
163
164
DRUM FG
DRUM PG
M902
CAPSTAN MOTOR
14
ı
9
M
7
ı
2
HU, HV, HW
18
16
CAPSTAN FG
22
DEW SENSOR
21
ı
19
S901
MODE SWITCH
69
72
CN2401
LM (+) , LM (–)
2
1
31
21
TAPE END
DETECT
20
19
TAPE TOP
DETECT
18
29
T REEL
FG AMP
26
27
T REEL (+) , (–)
9
10
T REEL H001
SENSOR
25
S REEL
FG AMP
22
23
S REEL (+) , (–)
6
7
S REEL H002
SENSOR
CN2404
TAPE END (C)
XSYS RST
USB XEN
VFI OE
ALIGN VD
BIRDS VD
BIRDS FLD
LINEOUT V
VREF
195
68
207
203
185
201
204
X4501
20MHz
XCS EEP
EEP SI, EEPSO, EEP SCK
1
2
5
6
Q001
TAPE END
SENSOR
D001
TAPE
LED
TAPE TOP
SENSOR
3
S001
13
12
14
15
S002
REC PROOF
ME/MP
HI8 MP
C. C. LOCK
13
OVERALL (2/6)
(PAGE 3-3)
CN1011 (2/3)
CAP FG
4
CPC
16 (FOR CHECK)
1
14
15
IC4502
SI-041 BOARD
(3/4)
VIDEO LIGHT
DRIVE
1
Q002
23
EEPROM
(14/18)
VL 16V
2
M
OVERALL (5/6)
(PAGE 3-9)
EEP SI, EEPSO, EEP SCK
Q1002
91
TAPE LED (K)
ME SW
HI8 MP SW
135
8
9
1
10
87
86
84
TAPE TOP (C)
REC PROOF
ME SW
HI8 MP SW
XCC DOWN
XCC DOWN
ZOOM VR AD
M903
LOADING MOTOR
LOADING
MOTOR
DRIVE
Q2401
LED DRIVE
TAPE LED ON
3
63
ı
66
HI SI, HI SO, XHI SCK, XCS MECHA
3
1
CN2403
21
XCS EEP
VSP SI, VSP SO, XVSP SCK
17
192
193
110
168
169
171
156
181
CAM SI, CAM SO, CAM SCK, CAM CS
OVERALL (2/6)
(PAGE 3-4)
30
M
Q1309
VD SI, VD SO, VD SCK
22
10
ı
5
U, V, W
IC2401 (2/3)
138
OVERALL (6/6)
(PAGE 3-11)
M901
DRUM MOTOR
CN2402
63
65
68
DRUM
MOTOR
DRIVE
SWITCHING
DRUM FG
DRUM PG
28
29
37
170
166
165
DRUM VS
DRUM FG
197
198
IC4501
SWITCHING
(15/18)
DRUM PG
189
HALL AD
128
LENS TEMP AD
127
XNS SW
187
94
PITCH AD
129
YAW AD
130
118
112
99
113
43
Q1310
CN754
(3/4)
CN1001 (3/4)
1
30
FP-792 FLEXIBLE
BOARD
D001 – 003
(VIDEO LIGHT)
VL+
LND754
V LIGHT PWM
A : VIDEO SIGNAL
A : SERVO SIGNAL
05
3-7
3-8
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
3. BLOCK DIAGRAMS
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
3-5. OVERALL BLOCK DIAGRAM (5/6)
CONTROL KEY
BLOCK (PR-5100)
VC-345 BOARD (5/6)
PD-205 BOARD (1/2)
S601
PANEL
REVERSE
SW
CN6005
1
2
CN6001 (1/2)
PANEL REV
20
20
CN1003 (1/2)
PANEL REV
OVERALL (2/6)
(PAGE 3-4)
CN1001 (4/4)
X5001
10MHz
CONTROL KEY BLOCK (SS-5100)
X5002
32.768kHz
CN1009
XPHOTO FREEZE
S003
PHOTO
KEY AD5
D004
XCHARGE LED
CHG
SI-041 BOARD (4/4)
IR ON
19
29
28
52
15
12
25
17
D753, 754
(IR EMITTER)
SIRCS PWM/
IR DRV EN
SIRCS PWM
45
D759
(TALLY)
CN754 (4/4)
XF TALLY LED
D1001
IC5001
51
XF TALLY LED
16
20
Q751
LED DRIVE
HI CONTROL
(13/18)
KEY AD5
14
XCHARGE LED
6
IC751
SIRCS SIG
41
14
REMOTE
1 COMMANDER
RECEIVER
XSIRCS SIG
23
9
S001
START/STOP
SW
CAMERA
D003
TAPE
XS/S SW
XCAM LED
D002
MEMORY
XMEM LED
D001
XVTR LED
PLAY/EDIT
(CHG)
OFF
S004
POWER
XPOWER SW
ON
>
XMODE SW
KEY AD6
1
XCAM LED
7
XMEM LED
8
XVTR LED
9
XPOWER SW
4
XMODE SW
3
10
CN1011 (3/3)
LANC OUT
11
CPC
LANC IN
12
XLANC POWER ON
(FOR CHECK)
13
11
12
40
39
7
1
2
MODE
S002
EJECT SW
XEJECT SW
16
ZOOM VR
12
XEJECT SW
4
RV001
BL REG
D 1.2V
A 1.5V
D 1.5V
RP 2.8V
A 2.8V
D 2.8V
AU 2.8V
D 1.9V
A 4.6V
AU 4.6V
EP 4.6V
RP 4.6V
RP 6.0V
MT 5V
VL 16V
CAM –7.5V
CAM 15V
EP 13.5V
5
14
KEY AD0, 1
Q1009
D002
XCUSTOM LED
EASY
9
LED
DRIVE
17
Q1006
XMS LED
D001
(MS ACCESS)
S001
DISP/
BATT INFO SW
S002
RESET SW
BT001
LITHIUM
BATTERY
11
6
22
3
LED
DRIVE
XBATT INFO SW
XRESET
6
OVERALL (2/6)
(PAGE 3-3)
23
ZOOM VR AD
XCC DOWN
XSYS RST
14
XSYS RST
LINEOUT V
5
18
32
MS LED ON
OVERALL (2/6)
(PAGE 3-4)
18
VTR UNREG
BATT UNREG
BT901
CN4001
Q4003, 4004
IC 5001RXD0, IC 5001 TXD0, IC 5001 SCK0, IC 5001 CS
23
ı
26
OSD V
XDS RESET
XVM MAD
KEY AD0, 1, 5, 6
19
44
33
77
37
38
BATT IN
VTR DD ON
XCS DD
43
42
BATT/XEXT
FAST CHARGE
INIT CHARGE ON
Q5001
BATTERY
CHARGE
DETECTOR
BATT SIG
CHARGE
CONTROL
6
44
38
26
39
XRESET
45
40
VBAT
REG 3V
D1301
+
–
DC IN
2
05
3-9
4
27
28
HI EVER SO, HI EVER SCK
31
35
67
Q4001, 4002
3
EVER 3.0V
VOUT
20
21
OVERALL (4/6)
(PAGE 3-8)
IC1301 (2/2)
DC CONTROL,
RESET,
LANC DRIVER
(17/18)
73
LI 3V
OVERALL (6/6)
(PAGE 3-11)
3-10
BATT SIG
CN1007
KEY AD0, 1
FUNCTION
SW
24
BATT/XEXT
CONTROL KEY BLOCK (CF-5100) (2/2)
BL CONT
14
FAST CHARGE
ZOOM VR AD
INIT CHARGE ON
ZOOM VR
+
5
S
1
–
BATTERY
TERMINAL
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
3. BLOCK DIAGRAMS
3-6. OVERALL BLOCK DIAGRAM (6/6)
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
VC-345 BOARD (6/6)
EVF BLOCK
CN1013
6
EVF DD ON
OVERALL (4/6)
(PAGE 3-7)
22
XCS LCD
EVF HD
EVF VD
EVF G/BW Y
LCD902
B/W
LCD UNIT
NSLEEP
HSYNC
VSYNC
2
4
5
VD SI, VD SO, VD SCK
OVERALL (5/6)
(PAGE 3-10)
24
BL CONT
PD-205 BOARD (2/2)
EVF G/BW Y
EVF HD, EVF VD
LCD901
CN1003 (2/2)
PANEL R
PANEL G
PANEL B
CN6001 (2/2)
10
9
8
13
PANEL R
PANEL G
PANEL B
XCS LCD D/A
CN6004
10
9
8
40
39
38
19
20
21
13
45
25
IC6001
PANEL HD, PANEL VD
OVERALL (2/6)
(PAGE 3-3)
PANEL HD
PANEL VD
12
11
C SYNC/XHD
PANEL XVD
LCD DRIVER
43
42
12
11
15
VD SI, VD SO, VD SCK
14
ı
16
14
ı
16
SI, SO, SCK
VR
VG
VB
VP
2
ı
4
6
14
15
32
ı
35
4
5
3
Q6004, 6005
PSIG DRIVE
6
RGT, HCK1, 2, REF, HST, WIDE, DWN, EN, VCK, VST
Q6008, 6009
TOUCH
PANEL I/F
PSIG
2.5 INCH
COLOR
LCD UNIT
2
RGT, HCK1,2,
7 REF, HST, WIDE,
8
DWN, EN,
11
VCK, VST
12
13
19
ı
22
CN6007
46
ı
48
R
G
B
1
4
5
2
TP R
TP BOT
TP TOP
TP L
TOUCH
PANEL
T6001, Q6003
4
TP X, TP Y, TP SEL1
TP SEL1
TP X
TP Y
6
5
7
BL CONT
TP SEL1
TP X
TP Y
4
28
29
30
INVERTER
TRANSFORMER
BL DET
BL REG
BACKLIGHT
DRIBE
10
ND901
BACKLIGHT
6
5
7
D6004
A : VIDEO SIGNAL
05
3-11
CN6003
BL HIGH
3-12
BL LOW
3
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
3. BLOCK DIAGRAMS
3-7. POWER BLOCK DIAGRAM (1/3)
BT901
BATTERY
TERMINAL
+
S
–
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
VC-345 BOARD (1/2)
Q4003, 4004
CHARGE
CONTROL
CN4001
BATT UNREG
+
BATT SIG
VIDEO
LIGHT
DRIVE
D4001
5
BATT GND
INIT CHARGE ON
1
CN1001
1
VL+
Q1316, 1318, 1320
F003
15
16
5V REG
F001
13
VTR UNREG
10
11
F004
ACV UNREG
MT 5V
A
D 2.8V
POWER(3/3)
(PAGE 3-17)
A 2.8V
4
Q4001, 4002
BATT/XEXT
–
Q1002
6
FAST CHARGE
DC IN
MT 5V
2
F002
ACV GND
3
V LIGHT PWM
MT 5V
55 VCC1
56 VCC0
D1302
BATT UNREG
VTR UNREG
IC1301
DC CONTROL, RESET
(17/18)
36 CDET
VIN
43
OUT1 57
IN1 20
IC5001
HI CONTROL
(13/18)
BATT SENSE 65
ACV SENSE 66
EVER 3.0V
37 FAST CHARGE
38 INIT CHARGE
LI 3V
BATT SIG
VTR DD ON
XCS DD
HI EVER SO
HI EVER SCK
XCS DD 67
FR EVER SO 20
BATT/XEXT
77 BATT/XEXT FR EVER SCK 21
BATT IN
BATT IN 31
VR 34
L1314
Q1307
L1303
A 2.8V
L1315
AU 2.8V
L1312
RP 2.8V
SWITCHING
OUT3 59
IN3 22
38 CTL1
Q1302, 1312, 1313
17
15
4
D001
(MS ACCESS)
13
CUSTOM LED VDD
CAM DD ON
44 CS
D1306
CAMERA
D003
TAPE
D004
CHG
EP 13.5V
L1308
1
5
IC1302
6V REG
(17/18)
MT 5V
A 4.6V
L1318
OUT4 60
IN4 23
D 2.8V
D 2.8V
D 2.8V
EP 4.6V
L1317
AU 4.6V
L1320
RP 4.6V
Q1315
MS LED VDD
D 1.2V
EVER 3.0V
Q1306
SWITCHING
30 RT
L1321
1.2V REG
OUT7 63
–INE7 2
L1302
L1310
37 VREF
1 DTC6
5
IC1305
4
DC
CONTROL
(17/18)
3
1
CN1003
19
EP 4.6V
+INE2 14
BL CONT
18
4
2
10
CHARGE LED VDD
MODE LED VDD
D002
MEMORY
D001
D 2.8V
D 2.8V
PLAY/EDIT
05
3-13
POWER(2/3)
(PAGE 3-15)
RP 6.0V
4
L1319
L1304
OUT2 58
IN2 21
5
B
L1301
CN1009
D 2.8V
11
T
Q1301, 1303
L1311
13.5V REG
CONTROL KEY
BLOCK (SS-5100)
RV001
W (ZOOM)
CAM 15V
+15V REG
CN1007
LI 3V
7
CAM –7.5V
–7.5V REG
SWITCHING
FUNCTION
SWITCH
Q1304, 1314
D1303
26 LD
27 DIN
28 CLK
Q1308
D002
EASY
D 2.8V
L1313
SWITCHING
3
D 1.9V
1.9V REG
Q1311
BT001
LITHIUM
BATTERY
D 1.5V
Q1326, 1327
HOTSHOE ID1 54
HOTSHOE ID2 55
CONTROL KEY
BLOCK (CF-5100)
A 1.5V
L1309
SWITCHING
REG 3V
42 VOUT
VTR DD ON 35
43 IB SI
42 IB SO
VRO
RST
VBAT
L1305
D1301
V OUT
Q5001
BATTERY
CHARGE
DETECTOR
41
29
39
40
Q1305
L1322
3-14
PANEL 13.3V
PANEL 4.6V
BL CONT
BL REG
C
POWER(3/3)
(PAGE 3-17)
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
3. BLOCK DIAGRAMS
3-8. POWER BLOCK DIAGRAM (2/3)
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
M2000/M2200 MECHA DECK
D001
M2000: TRV460/TRV460E/TRV461E
M2200: TRV360/TRV361
H001,002
EVF BLOCK
LCD902
TAPE
LED
T REEL,
S REEL,
SENSOR
CAPSTAN
FG
HU, HV, HW
4
8
17
8
CN1013
IC3201
IC3001
REC/PB
AMP
(8/18)
Hi8/Std8
PB AMP
(10/18)
EVF 4.6V
3
CN2403
VH+
FG VCC
TRV460/TRV460E/TRV461E
SENSOR VCC
CN2404
VC-345 BOARD (2/2)
TAPE LED (A)
EP 4.6V
B/W
LCD
UNIT
3.3V
1
IC1001
IC2401
3.3V REG
(18/18)
5
DRUM/
CAPSTAN/LOADING
MOTOR
DRIVE VMR 3
VH 17
(15/18)
4
1
FB2401
L3001
L3202
USB 3.1V
IC1552
RP 4.6V
TIMING
GENERATOR
(1/18)
MT 5V
CAM –7.5V
CAM 15V
A 1.5V
D 1.5V
D1.9V
D 2.8V
A 2.8V
AU 2.8V
MT 5V
CAM –7.5V
CAM 15V
A 2.8V
D 1.5V
D1.9V
D 2.8V
A 2.8V
IRIS DRIVE,
HALL BIAS CONTROL,
HALL GAIN CONTROL,
HALL AMP
(4/18)
IC1554
FOCUS/ZOOM
MOTOR DRIVE
(4/18)
L1553
FB1501
IC1501
S/H. AGC.
A/D CONVERTER
(1/18)
L1501
IC1502
STEADY
SHOT
(9/18)
L2001
MT 5V
VTR UNREG
EP 13.5V
IC2001
FB1502
V LIGHT PWM
MT 5V
VTR UNREG
CAP VS
DRUM VS
CD-472 BOARD
L1552
L3201
D 2.8V
CN1501
CN951
L951
CN1551
D 2.8V
D 2.8V
24
18
IC5401
AUDIO PROCESS
(16/18)
CAM DD ON
EP 13.5V
RP 6.0V
EP 4.6V
A 4.6V
AU 4.6V
RP 4.6V
D 1.2V
IC5402
AUDIO
A/D, D/A
CONVERTER
(16/18)
IC5801
MIC AMP
(16/18)
IC1601
IC8301
EVR
(D/A CONVERTER)
(10/18)
TEMP
VIDEO IN/OUT
(6/18)
FC SENS VCC
IC4502
CAMERA/MECHA
CONTROL
(14/18)
EEPROM
(14/18)
5
2.9V REG
(18/18)
4
3
7
VCC
1
EP 4.6V
91 STROBO PWM
D 1.2V
D 2.8V
A 2.8V
D 2.8V
CN1015
USB 3.1V
FOR JIG
FB5702
FB5701
FB5703
FB5704
FB5501
FB5502
L6001
L6004
L6007
L6008
FB6002
L6003
FB2205
L2202
L2208
FB2204
FB2202
L2209
D 2.8V
IC8001
IC8002
IC8501
IC6001
IC5502
IC5501
IC5703
IC5702
IC5701
VIDEO/AUDIO DSP,
D/A CONVERTER,
LENS CONTROL
(2/18)
16M SDRAM
(3/18)
A/D CONVERTER
(3/18)
DV SIGNAL PROCESS
(7/18)
32M FLASH
(12/18)
16M SDRAM
(12/18)
XTAL OSC
(11/18)
EEPROM
(11/18)
USB CONTROL,
MEMORY STICK
INTERFACE,
MODE CONTROL
(11/18)
IC2201
Hi8/Std8 VTR PROCESS
(5/18)
TRV460/TRV460E/TRV461E
CAM DD ON
MS VCC ON 286
CAM DD ON
131 CAM DD ON
05
3-15
8
D 1.2V
FB8502
FB8501
FB8003
L8002
FB8002
FB8001
L8003
USB 3.1V
IRIS
METER
TEMP
SENSOR
ZM SENS VCC
ZM RST LED 55
FC RST LED 57
USB 3.1V
A 1.5V
D 1.5V
LENS BLOCK
ZOOM
SENSOR
FOCUS
SENSOR
CN1016
IC1002
IC4501
IC3701
DV INTERFACE
(9/18)
IRIS DRIVE (+)
FB4501
FB1601
CAM –7.5V
CAM 15V
13
FB8301
FB8302
L8301
AU 2.8V
AU 4.6V
FB1602
POWER (1/3)
(PAGE 3-14)
16
A 4.6V
L3705
A 4.6V
L3701
RP 2.8V
CCD
IMAGER
D 1.5V
Q1555
B
IC951
CAM –7.5V
12
3
CAM 15V
10
5
3-16
3
MEMORY
STICK
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
3. BLOCK DIAGRAMS
3-9. POWER BLOCK DIAGRAM (3/3)
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
SI-041 BOARD
D753, 754
(IR EMITTER)
CN754
MT 5V
21
22
D 2.8V
24
IC751
REMOTE
COMMANDER
RECEIVER
D759
(TALLY)
A
POWER(1/3)
(PAGE 3-14)
SE751, 752
A 2.8V
VL+
FP-792 FLEXIBLE BOARD
PITCH, YAW
SENSOR
26
27
D001 – 003
(VIDEO LIGHT)
LND754
36
PD-205 BOARD
PANEL 13.3V
PANEL 4.6V
CN6004
VDD
18
Q6006
CN6001
19
18
5
1
IC6002
2.8V REG
VDOG
4
L6001
16
LCD901
2.5INCH
COLOR
LCD UNIT
D6001
IC6001
LCD DRIVER
C
POWER(1/3)
(PAGE 3-14)
BL CONT
28 EXTDA
29 FBACK XPOFF 16
4
L6002 L6003
BL REG
2
T6001, Q6003
INVERTER
TRANSFORMER
CN6003
BL HIGH
10
BACKLIGHT
DRIVE
ND901
BACK
LIGHT
05
3-17
3-18E
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
4-2. SCHEMATIC DIAGRAMS
4-3. PRINTED WIRING BOARDS
SECTION 4
PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
4-1. FRAME SCHEMATIC DIAGRAMS
1
3
2
4
6
5
7
9
8
11
10
13
12
14
17
16
15
18
19
20
21
FRAME SCHEMATIC DIAGRAM
A
CN951 14P
2
MIC_GND
XCAM_LED
7
MIC_GND
34
3
MIC_GND
XMEM_LED
8
INT_MIC_L
33
4
INT_MIC_L
XVTR_LED
INT_MIC_R
32
5
INT_MIC_R
MODE_LED_VDD
10
VREF1
31
6
VREF1
D_2.8V
11
LIA1
ZOOM_VR
12
REG_GND
13
KEY_AD5
14
XPHOTO_FREEZE
15
XEJECT_SW
16
7
LIA1
29
8
LIA2
28
9
VREF2
15
EEP_SI
A_2.8V
27
10
A_2.8V
14
EEP_SO
A_2.8V
26
11
A_2.8V
13
XLANC_POWER_ON
XF_TALLY_LED
25
12
XF_TALLY_LED
12
LANC_IN
D_2.8V
24
13
D_2.8V
11
LANC_OUT
XSIRCS_SIG
23
14
XSIRCS_SIG
10
REG_GND
MT_5V
22
15
MT_5V
CPC
9
RF_MON
MT_5V
21
16
MT_5V
(FOR CHECK)
8
REG_GND
SIRCS_PWM/IR_DRV_EN
20
17
SIRCS_PWM/IR_DRV_EN
AV_JACK_IN
19
18
AV_JACK_IN
AUDIO_L_I/O
18
19
AUDIO_L_I/O
AUDIO_R_I/O
17
20
AUDIO_R_I/O
REG_GND
16
21
REG_GND
VIDEO_I/O
15
22
VIDEO_I/O
REG_GND
CN1011 16P
16
XCS_EEP
9
VIDEO_IN
VSYNC
HSYNC
EVF_4.6V
NSLEEP
3.3V
6
5
4
3
2
1
NC
DIG_GND
NC
CN1015 8P
VC-345 BOARD
MS_SCLK
1
MS_LED_ON
2
D_2.8V
3
REG_GND
4
5
(FOR JIG)
7
N.C
MS_XIN
6
REG_GND
MS_DIO
6
5
SW_DIR
MS_BS
7
4
CAP FG
3
BPF MONI
2
8mm PB RF
1
EEP_SCK
USB_3.1V
8
CN1016 8P
VSS
1
14
23
REG_GND
BS
2
S_Y_I/O
13
24
S_Y_I/O
VCC
3
XS_JACK_IN
12
25
XS_JACK_IN
DIO
4
S_C_I/O
11
26
S_C_I/O
INS
5
REG_GND
10
27
REG_GND
SCLK
6
NTPA
VCC
7
VSS
8
MS_LED_VDD
KEY_AD1
D_2.8V
KEY_AD3
D_2.8V
KEY_AD2
DIAL_A
DIAL_B
REG_GND
XRESET
13
14
15
16
17
18
19
20
21
22
XMS_LED
11
N.C
REG_GND
10
12
XCUSTOM_LED_ON
9
2P
N.C
1
SE_GND
8
2
BL_REG
CUSTOM_LED_VDD
3
BL_GND
BATT_INFO
4
BL_CONT
7
5
TP_X
6
6
TP_SEL1
KEY_AD0
7
TP_Y
5
8
PANEL_B
D_2.8V
9
4
10
PANEL_R
PANEL_G
LI_3V
11
PANEL_XVD
3
12
C-SYNC/XHD
N.C
13
REG_GND
14
VD_SCK
XCS_LCD_DA
2
15
VD_SO
CN1007 22P
16
VD_SI(HDO)
1
17
REG_GND
SP(+)
18
PANEL_4.6V
SP(-)
19
PANEL_13.3V
CN1008
20
MEMORY STICK
BT901
BATTERY
TERMINAL
LCD901
(2/2)
TOUCH
PANEL
3
2
1
TP_R
1
LED_GND
4
2
LED
N.C.
3
BL_LOW
TP_L
4
N.C
TP_BOT
5
N.C
5
6
N.C
6
7
N.C
N.C.
8
N.C
TP_TOP
9
24
TEST1
23
COM
18
VDD
22
17
VSS
VST
16
VDOG
21
15
VVSSG
VCK
14
CS
20
13
EN
12
HST
DWN 19
11
REF
8
HCK2
WIDE
7
9
6
HCK1
10
5
G
PSIG
SOUT
4
R
CRext
3
B
CN6007 6P
PD-205
BOARD
N.C
PANEL_REV
10
PANEL_REV
BL_HIGH
N.C.
1
CN6003 10P
3
2
2
N.C.
1
4
MEMORY
STICK
CONNECTOR
6P
24P
SE_GND
RGT
SE_GND
5
TEST2
6
ND901
BACKLIGHT
CN6004
CN6005
CONTROL
KEY
BLOCK
(PR-5100)
PANEL_REV
CN6001 20P
L
2
SE_GND
1
LCD901(1/2)
2.5INCH
COLOR
LCD UNIT
1
BL_REG
2
USB_DET
BL_GND
USB_D+
36
3
35
1
BL_CONT
2
4
USB_D+
USB_DET
TP_X
USB_D-
5
34
TP_SEL1
6
3
6
5
USB_D-
TP_Y
BATT_SIG
BATT_UNREG
REG_GND
PANEL_B
4
NTPB
33
7
3
ACV_UNREG
32
4
8
2
ACV_GND
5
PANEL_G
1
BATT/XEXT
NTPB
PANEL_R
BATT_GND
9
TPB
10
31
PANEL_XVD
6
C-SYNC/XHD
TPB
11
CN4001 6P
12
REG_GND
XCS_LCD_DA
TPA
30
VD_SCK
NTPA
29
7
13
28
8
14
9
TPA
REG_GND
REG_GND
CONTROL
KEY
BLOCK
(SS-5100)
FP-799
FLEXIBLE
FP-796 FLEXIBLE
30
LIA2
VREF2
PD-124
HARNESS
M
ANA_GND
1
PG
35
VD_SO
TPA
MIC_GND
VD_SI(HDO)
4
VL+
15
NTPA
6
1
16
TPB
3
5
36
REG_GND
2
4
XCHARGE_LED
VL+
PANEL_4.6V
NTPB
3
CHARGE_LED_VDD
CN1001 36P
CN754 36P
17
DV
K
1
1
2
3
4
CN751 4P
1
2
18
GND
8
XS/S_SW
REG_GND
PANEL_13.3V
ID
5
7
XMODE_SW
19
D+
4
FP-797
FLEXIBLE
6
XPOWER_SW
PANEL_REV
3
5
DIG_GND
20
D-
4
VIDEO_IN
CN1003 20P
(USB)
2
3
VSYNC
INT_MIC_L
GND
GND
CN753 4P
INT_MIC_R
REG_GND
REG_GND
VL+
LND754
LND763
LND757
J
VCC
2
HSYNC
ANA_GND
SI-041
BOARD
1
1
CN1009 16P
H
CN752 5P
8
2
FG-PG_COM
MIC901
MICROPHONE
R
L
F
I
9
3
3.3V
NSLEEP
E
G
10
4
FG
1
5
W
COM
2
6
W
LM(-)
7
V
LM(+)
8
V
CN2401 2P
9
U
CN1013 8P
EVF_4.6V
FP-792
FLEXIBLE
BOARD
7
PG
COM
FG
FG-PG_COM
W
V
V
10
U
CN2402 10P
1
GND
1
VH-
2
2
HW2
GND
3
HW1
3
4
HV2
GND
5
HV1
4
6
HU2
5
7
HU1
6
8
VH+
GND
9
CAP_V
XODD(SP1X)
10
CAP_V
LM
FP
YODD(SP1Y)
11
CAP_W
7
12
CAP_W
XEVEN(SP2X)
13
CAP_U
8
14
CAP_U
9
15
REG_GND
10
16
FG2
GND
17
FG VCC
FE(Y)
18
FG1
YEVEN(SP2Y)
19
11
20
M-SW(C)
FE(X)
21
M-SW(A)
M-SW(B)
W
U
U
GND
GND
GND
XODD(SP1X)
YODD(SP1Y)
GND
GND
XEVEN(SP2X)
FE(Y)
YEVEN(SP2Y)
VH-
FE(X)
HW2
HW1
HV2
HV1
HU2
HU1
VH+
CAP_V
CAP_V
CAP_W
CAP_W
CAP_U
CAP_U
REG_GND
FG2
FG VCC
FG1
M-SW(C)
M-SW(B)
22
15
C_LOCK_SW
FP
DEW
14
HI8_MP
CN2403 22P
13
T_REEL(-)
12
9
10
T_REEL(+)
11
8
SENSOR_VCC
ME/MP
7
HALL_COM
6
REC_PROOF
5
REG_GND
S_REEL(-)
FP
S_REEL(+)
4
TAPE_LED(A)
1
3
2
2
3
V4
1
4
V3
TAPE_LED(K)
5
V2
15P
6
V1
CN2404
7
GND
TAPE_TOP(C)
8
H2
TAPE_END(C)
9
4
FOCUS_A
H1
5
IR_SWITCH
10
6
IR_SWITCH
RG
7
ZOOM_XA
11
8
ZOOM_XB
GND
9
ZOOM_B
12
10
ZOOM_A
CAM_15V
11
GND
13
12
FC_SENSE_OUT
GND
13
FC_SENSE_VCC
VSHT
14
LENS_DET
CAM_-7.5V
15
ZM_SENSE_OUT
1
16
ZM_SENSE_VCC
14
17
TEMP
CCD_OUT
18
TEMP
2
19
IRIS_DRIVE(-)
CN1501 14P
20
IRIS_BIAS(-)
3
21
IRIS_HALL(-)
FOCUS_XA
22
IRIS_BIAS(+)
FOCUS_B
23
IRIS_HALL(+)
FOCUS_XB
24
IRIS_DRIVE(+)
FP
CN3201 11P
D
CN1551 24P
EVF BLOCK
LCD902
B/W
LCD
UNIT
M-SW(A)
1
C_LOCK_SW
2
DEW
3
GND
CCD_OUT
HI8_MP
4
ME/MP
VSHT
CAM_-7.5V
M2000/M2200 MECHANISM DECK
HALL_COM
5
REC_PROOF
6
SENSOR_VCC
7
TAPE_TOP(C)
C
RG
GND
CAM_15V
M2000: TRV460/TRV460E/TRV461E
M2200: TRV360/TRV361
FFC-005
FLEXIBLE
FLAT CABLE
T_REEL(-)
CD-472
BOARD
8
T_REEL(+)
LENS
BLOCK
9
H1
S_REEL(-)
10
H2
S_REEL(+)
11
GND
REG_GND
12
V1
B
TAPE_END(C)
13
V2
TAPE_LED(A)
14
V3
TAPE_LED(K)
V4
SP901
SPEAKER
CONTROL
KEY
BLOCK
(CF-5100)
N
05
4-1
4-2
FRAME
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
4-2. SCHEMATIC DIAGRAMS
Link
CD-472 BOARD (CCD IMAGER)
PD-205 BOARD
(LCD DRIVER, BACKLIGHT DRIVE)
SI-041 BOARD (STEADYSHOT, JACK)
FP-792 FLEXIBLE BOARD
FP-228, FP-299, FP-300, FP-301, FP-302,
FP-802 FLEXIBLE BOARD
COMMON NOTE FOR SCHEMATIC DIAGRAMS
CONTROL KEY BLOCK (SS-5100)
CONTROL KEY BLOCK (PR-5100)
CONTROL KEY BLOCK (CF-5100)
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
4-2. SCHEMATIC DIAGRAMS
4-2. SCHEMATIC DIAGRAMS
THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS
(In addition to this, the necessary note is printed in each block)
(For schematic diagrams)
• All capacitors are in µF unless otherwise noted. pF : µ
Link
µF. 50 V or less are not indicated except for electrolytics
and tantalums.
• Chip resistors are 1/10 W unless otherwise noted.
kΩ=1000 Ω, MΩ=1000 kΩ.
• Caution when replacing chip parts.
New parts must be attached after removal of chip.
Be careful not to heat the minus side of tantalum
capacitor, Because it is damaged by the heat.
• Some chip part will be indicated as follows.
Example
C541
L452
22U
10UH
TA A
2520
1. Connection
Pattern box
1m
Front of the lens
Kinds of capacitor
Case size
External dimensions (mm)
• Constants of resistors, capacitors, ICs and etc with XX
indicate that they are not used.
In such cases, the unused circuits may be indicated.
• Parts with ★ differ according to the model/destination.
Refer to the mount table for each function.
• All variable and adjustable resistors have characteristic
curve B, unless otherwise noted.
• Signal name
XEDIT → EDIT
PB/XREC → PB/REC
• 2: non flammable resistor
• 5: fusible resistor
• C: panel designation
• A: B+ Line
• B: B– Line
• J : IN/OUT direction of (+,–) B LINE.
• C: adjustment for repair.
• A: VIDEO SIGNAL (ANALOG)
• A: AUDIO SIGNAL (ANALOG)
• A: VIDEO/AUDIO SIGNAL
• A: VIDEO/AUDIO/SERVO SIGNAL
• A: VIDEO/SERVO SIGNAL
• A: SERVO SIGNAL
• Circled numbers refer to waveforms.
(Measuring conditions voltage and waveform)
• Voltages and waveforms are measured between the
measurement points and ground when camera shoots
color bar chart of pattern box. They are reference values
and reference waveforms.
(VOM of DC 10 MΩ input impedance is used)
• Voltage values change depending upon input
impedance of VOM used.)
Note :
A B
Red
Blue
White
Magenta
H
Cyan
Green
Yellow
2. Adjust the distance so that the output waveform of
Fig. a and the Fig. b can be obtain.
A=B
B A
Fig. a (Video output terminal output waveform)
Fig.b (Picture on monitor TV)
When indicating parts by reference number, please
include the board name.
Note :
The components identified by mark 0 or
dotted line with mark 0 are critical for safety.
Replace only with part number specified.
4-5
Les composants identifiés par une marque
0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
le numéro spécifie.
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
4-2. SCHEMATIC DIAGRAMS
CD-472 BOARD
For Schematic Diagram
• Refer to page 4-57 for printed wiring board.
1
2
3
1
CD-472 BOARD
A
5
4
2
IC951 1 REC
CCD IMAGER
6
7
3
IC951 2 REC
7.6 Vp-p
XX MARK:NO MOUNT
NO MARK:REC/PB MODE
R:REC MODE
P:PB MODE
8
IC951 3 REC
22 Vp-p
V
9
7.6 Vp-p
V
V
LND951
C954
XX
B
4
IC951 4 REC
GND
10
H2
9
H1
8
RG
7
GND
6
R11.5/P0
R-0.3/P0
R-0.3/P0
6
7
CCD_OUT
11
5
GND
V1
4
NC
12
3
V1
13
V2
2
V2
V3
1
ICX219CKA-43:TRV360
/TRV361
/TRV460
ICX223CKA-43:TRV460E
/TRV461E
5
4
CAM-7.5V
3
GND
2
CCD_OUT
1
H2
H1
RG
VL
SUB
NC
VDD
13
12
11
10
9
8
R10.2/P0.1
5
VSHT
14
R-7.6
/P0.4
CAM_15V
D951
XX
R12.5
/P0
D
R969
XX
R1.6
/P0
PAGE 4-9
of LEVEL3
R1.3
/P0
THROUGH THE FFC-005
FLEXIBLE FLAT CABLE
IC951 7 REC
1.9 Vp-p
CN1501
R15.0/P0
VC-345
(1/18)
14
V3
C
V4
R-7.2
/P0
CCD IMAGER
IC951
CN951 14P
V
V4
IC951
R-7.2/P0
22 Vp-p
H
C957
XX
R970
0
9
IC951 q; REC
R968
XX
22 Vp-p
E
C955
0.1u
R15/P0
L951
100uH
C951
22u
16V
SIGNAL PATH
F
VIDEO
SIGNAL
H
Q951
2SC4178-F13F14-T1
BUFFER
6
C952
XX
R952
82
IC951 qf REC
R11.5
/P0
R953
3300
7
R10.7
/P0
8
C953
47u
10V
IC951 qs REC
2.6 Vp-p
13.5 MHz
IC951 qd REC
Y/CHROMA
Precautions for Replacement of CCD Imager
• The CD-472 board mounted as a repair part is not equipped
with a CCD imager.
When replacing this board, remove the CCD imager from the
old one and mount it onto the new one.
• If the CCD imager has been replaced, carry out all the
adjustments for the camera section.
• As the CCD imager may be damaged by static electricity from
its structure, handle it carefully like for the MOS IC.
In addition, ensure that the receiver is not covered with dusts
nor exposed to strong light.
3.6 Vp-p
3.6 Vp-p
REC
H
H
G
05
4-7
4-8
CD-472
Schematic diagrams of the VC-345 board are not shown.
Pages from 4-9 to 4-44 are not shown.
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
4-2. SCHEMATIC DIAGRAMS
PD-205 BOARD
For Schematic Diagram
• Refer to page 4-63 for printed wiring board.
1
2
3
4
5
6
7
10
9
8
11
13
12
14
15
17
16
18
PD-205 BOARD
A
LCD DRIVER,BACKLIGHT
XX MARK:NO MOUNT
NO MARK:REC/PB MODE
5
1
2
4.7
PANEL_4.6V
18
REG_GND
17
3
H
C6025
XX
15
SI
VD_SCK
14
XCS_LCD_DA
13
C-SYNC/XHD
12
L6001
47uH
C6016
XX
0.1
XPOFF
C6006
0.01u
XLED
EXTDA
28
27
26
25
VP
29
XLED
30
7
13.4
2.6
2
1.9
2.8
31
CN6004 24P
CL6008
BIN
IC6001 rs REC/PB
COM
6.7
GIN
0.01u
VCC2
2.8 Vp-p
1.7
RIN
VB
VG
20
41
V
SCAN
CL6012
13.4
7
CL6004
XPOFF
44
XSCK
SI
WIDE
19
7
RB6001
10
VDD
OP_OUT
OP_IN
XCLR
Filter2
Filter
VSS
1
2
3
4
5
6
7
8
9
10
11
12
R6026
XX
0
XPOFF
HCK2
0.2
WIDE
TP_TOP
5
N.C.
6
VVSSG
14
CS
13
WIDE
12
HST
11
REF
10
SOUT
9
CRext
8
HCK2
7
HCK1
6
PSIG
5
G
4
R
3
B
2
RGT
1
TEST2
LCD901
(1/2)
2.5INCH
COLOR
LCD
UNIT
HCK1
0.1
HST
VG
2.8
VR
R6022
10k
7.6
Q6005
HN1B04FE-Y/GR(TPLR3)
4
1.2
1.3
2.6
1.4
13.4
IC6001 ql REC/PB
VP
6
5
2
7.6
R6008
XX
7
R6019
10k
6.4
2H
CL6011
1
REF
Q6007
XX
C6010
560p
D6006
XX
R6009
68k
3
5
2
R6012 10k
1/16W ± 0.5%
6.4
7
6
C6009
0.1u
1
3
7.0 Vp-p
C6022
XX
R6027
XX
R6023
150k
7
HCK2
4
C6018
0.1u
16V
C6015
0.1u
CL6002
HCK1
3
VDOG
15
HST
H
RGT
2
N.C.
VSS
16
REF
9
TP_L
VDD
17
RGT
2.8
2.8 Vp-p
REF
G
TP_BOT
DWN
18
VB
1.4
IC6001 rd REC/PB
13
SO
1.4
48
R6030 470
5
14
HST
2.7
LCD901
(2/2)
TOUCH
PANEL
CL6006
0.2
HDO
SO
1
EN
19
2.7
SI
TP_R
VCK
20
WIDE
18
15
SCK
CN6007 6P
C6017
1u
VR
17
16
XCS
HCK2
6
VB
CL6005 VG
2.8
0
SE_GND
GND1
HCK1
5
1.4
4
VCC1
RGT
N.C.
SE_GND
GND2
LCD DRIVER
IC6001
CXA3622BR-T4
XWRT/CLKIN
PAGE 4-50
of LEVEL2
VR
IC6001
7.1
D6001
RD3.3UM-T1B
2.8
XCS
45
3
HD
2.7
46
N.C.
XVD
2.8
XHD
47
2
42
CN6005 6P
43
XVD
1
VST
21
DWN
1.7
E
PANEL_REV
COM
22
EN
1.7
PANEL_REV
TEST1
23
VST
24
23
0.01u
4
22
C6004
NC
21
0.01u
VDD
2.8
38
C6003
C6005
CONTROL
KEY
BLOCK
(PR-5100)
24
VCK
1
SE_GND
32
C6014
4.7u
10V
VP
H
2
BL_REG
33
R6018
XX
VCC3
3
34
FBACK
BL_GND
35
EXTDA
4
36
PWM
BL_CONT
340 mVp-p
BLDET
5
DWN
6
39
D
7
TP_X
2.5
8
TP_Y
TP_SEL1
IC6001 ek REC/PB
EN
PANEL_B
1
VCK
9
0.1
10
PANEL_G
VST
PANEL_R
PAGE 4-44
of LEVEL3
BLDET
C6020
3.3u
25V
C6002
1u
VSS
11
37
PANEL_XVD
1.4
C6019 C6001
0.1u
22u
4V
XVD
THROUGH THE
PD-124 HARNESS
H
13.4
XCS
XHD
CN1003
F
Q6006
NDS356AP
VDD SWITCH
2H
R6021
100k
40
VC-345
(18/18)
2H
FB6001
XX
SCK
C
7.0 Vp-p
13.4
VST
16
VD_SO
IC6001 w; REC/PB
7.0 Vp-p
2H
SO
VD_SI(HDO)
8
IC6001 wa REC/PB
5.0 Vp-p
H
FB6002
XX
EN
19
7
IC6001 wg REC/PB
360 mVp-p
DWN
20
6
IC6001 r; REC/PB
360 mVp-p
CN6001 20P
PANEL_REV
PANEL_13.3V
3
IC6001 el REC/PB
2.8V REG
IC6002
TK11128CSCL-G
VCK
B
2.8
4
1.3
C6029
0.1u
6.3V
2
IC6002
4.7
R6013 100k
1/16W ± 0.5%
13.4
Q6004
HN1B04FE-Y/GR(TPLR3)
4
7
Q6004,6005
PSIG DRIVE
C6027
XX
I
2.8
1
C6028
2200p
R6029
XX
Q6009
UP04111008S0
EXTDA
R6028
XX
2.8
4
L6002
4.7uH
L6003
82uH
R6005
1800
1/10W
5
2.8
2.8
2
J
5
6
0
1
3
2
6
2.8
C6011
0.015u
Q6008,6009
TOUCH PANEL
I/F
2.8
0
6
2
Q6008
UP04111008S0
K
4
10
-0.6
5
C6007
4.7u
10V
4
6
1
2
2.8
1
CN6003
3
5
4
5.5
Q6002
XX
C6013
12p
4
1
3
T6001
INVERTER
TRANSFORMER
5.5
2
5
Q6003
TPC6C01(TE85R)
INVERTER DRIVE
R6011
XX
Q6001
XX
D6002
XX
D6004
MA111-(K8).S0
XLED
10
BL_HIGH
9
N.C
8
N.C
7
N.C
6
N.C
5
N.C
4
N.C
3
BL_LOW
VIDEO SIGNAL
CHROMA
ND901
BACKLIGHT
REC
PB
2
LED
1
LED_GND
(N,C)
(SE_GND)
D6005
XX
BLDET
L
R6001 XX
LND605
R6010
22k
C6012
0.1u
R6014
470
R6002 XX
A
D6003 XX
05
PD-205
SIGNAL PATH
10P
-0.6
3
0
3
4-45
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
4-46
Les composants identifiés par une marque 0 sont
critiques pour la sécurité. Ne les remplacer que
par une piéce portant le numéro spécifié.
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
4-2. SCHEMATIC DIAGRAMS
SI-041 BOARD, FP-792 FLEXIBLE BOARD
For Schematic Diagram
• Refer to page 4-65 for printed wiring board.
1
2
4
3
5
6
8
7
9
11
10
12
SIGNAL PATH
A
VIDEO SIGNAL
Y
CHROMA
Y/CHROMA
AUDIO
SIGNAL
FP-792 FLEXIBLE BOARD
VIDEO LIGHT
REC
D002
NSPW500BS-TL2
PB
REG_GND
1
VL+
B
D001
NSPW500BS-TL2
D003
NSPW500BS-TL2
D001-003
(VIDEO LIGHT)
LAND1
STATIC_GND
REG_GND
3
STATIC_GND
LAND2
C
SI-041 BOARD
LND757
REG_GND
STEADYSHOT,JACK
LND763
REG_GND
D
1
LND754
VL +
XX MARK:NO MOUNT
NO MARK:REC/PB MODE
Note: CN751, CN752, D753, D754, IC751, J751 and J752 are
not included in SI-041 complete board.
R759
XX
C754
XX
MIC901
MICROPHONE
CN753 4P
1.3
2.8
1.3
LIA1
Vref1
GND
3
R761
XX
2.8V
4
3
R760 XX
1
1
INT_MIC_L
2
GND
3
INT_MIC_R
4
GND
L
2
R
SE752
PITCH
SENSOR
SE751
YAW
SENSOR
LINE
E
LINE
Vref2
1
4
J751
S VIDEO
8
S3
C
Y
S
S
S2
5
G
G
2
2.8V
2.8
C753
XX
4V
C759
4.7u
C751
XX
1
7
S4
IC751
YGND
F
R762
XX
C758 C755
4.7u XX
4V
FB751
REMOTE COMMANDER
RECEIVER
IC751
RPM7240-V4
LINE
GND
R OUT
6 NC
LINE
Q751
2SD2114KT146
LED DRIVE
G
2.8
VCC
3
GND
L
V
BR
SW
R
2
1
2
3
4
5
7
R751
XX
LINE
D756
RSE6.8XN-TR
D752
RSE6.8XN-TR
R752
56
D754
SI50-RH51CSH870IT
(IR EMITTER)
R753
56
D753
SI50-RH51CSH870IT
(IR EMITTER)
VDR757 XX
D759
TLRMV1021(T15SOY,F)
(TALLY)
R755
XX
LINE
C752
XX
LINE
D751
RSE6.8XN-TR
LINE
LND765
STATIC_GND
LINE
H
36
VL+
35
MIC_GND
34
MIC_GND
33
INT_MIC_L
32
INT_MIC_R
31
VREF1
30
LIA1
29
LIA2
28
VREF2
27
A_2.8V
26
A_2.8V
25
XF_TALLY_LED
24
D_2.8V
23
XSIRCS_SIG
22
MT_5V
21
MT_5V
20
SIRCS_PWM/IR_DRV_EN
19
AV_JACK_IN
18
AUDIO_L_I/O
17
AUDIO_R_I/O
16
REG_GND
15
VIDEO_I/O
14
REG_GND
13
S_Y_I/O
12
XS_JACK_IN
11
S_C_I/O
10
REG_GND
9
NTPA
8
TPA
7
REG_GND
6
TPB
5
NTPB
4
REG_GND
3
USB_D-
2
USB_D+
1
USB_DET
2.8
3
0.2
R763
1k
C757
XX
1
A/V
4
S
S
CGND
J752
3
1.3
R754
XX
S1
6
1.3
Y
3
CN754 36P
LIA2
2
GND
C
VC-345
(9/18)
CN1001
THROUGH THE
FP-796 FLEXIBLE
PAGE 4-25
of LEVEL3
LINE
LINE
LINE
LINE
LINE
LINE
D755
MA728-(K8).S0
USB
I
LF751
XX
CN752 5P
GND
5
ID
4
D+
3
D-
2
VCC
1
(USB)
R756 0
USB
USB
USB
USB
R765
10k
R757
0
USB
R764
10k
C756
XX
USB
USB
USB
USB
USB
USB
J
LF752
XX
CN751 4P
DV
K
TPA
4
NTPA
3
TPB
2
NTPB
1
D760
XX
LND764
STATIC_GND
L
05
4-47
4-48
SI-041, FP-792
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
4-2. SCHEMATIC DIAGRAMS
FP-228, 299, 300, 301, 302, 802 FLEXIBLE BOARD
For Schematic Diagram
• Refer to page 4-67 for printed wiring board.
1
FP-300
FLEXIBLE
ME/MP
REC PROOF
Hi8 MP
S001
15
C_LOCK_SW
2
S001
(START/STOP)
C
S003
D001
R001 1k
D002
D004
1
POWER/MODE_SW
S901
MODE SWITCH
1
DEW
2
M-SW (A)
3
M-SW (B)
4
M-SW (C)
1
5
FG1
2
MR
SENSOR 3
6
FG VCC
7
FG2
4
8
REG_GND
9
CAP_U
10
CAP_U
11
CAP_W
12
CAP_W
13
CAP_V
14
CAP_V
15
VH+
16
HU1
17
HU2
18
HV1
19
HV2
20
HW1
DEW SENSOR
M902
CAPSTAN MOTOR
FP-228
FLEXIBLE
3
4
2
HE
3
4
2
HE
1
21
HW2
22
VH-
HE
W
VC-345 BOARD
(15/18)
D001
T
(ZOOM)
05
CN2403
PAGE 4-37
of LEVEL3
1
2
3
4
CONTROL KEY BLOCK
(PR-5100)
A
XX MARK:NO MOUNT
•
B
REC/PB
CONTROL KEY BLOCK (PR-5100) is replaced as block,
so that PRINTED WIRING BOARD is omitted.
S601
(PANEL REVERSE)
PB
Capstan speed servo
Capstan servo(speed and phase)
1
PANEL_REV
2
PANEL_REV
3
N.C
PD-205
4
N.C
5
SE_GND
CN6005
PAGE 4-45
of LEVEL2
6
SE_GND
C
4-49
FP-228, FP-299, FP-300, FP-301, FP-302, FP-802, SS-5100, PR-5100
S002
(EJECT)
RV001
20k
E
1
SIGNAL PATH
XMODE_SW
MODE
2
3
4
1
CAMERA
XPOWER_SW
PLAY/EDIT
ON
MEMORY D002
REG_GND
D003
S004
TAPE
D
D004
(CHG)
OFF
CHG
POWER
REC
4
PHOTO
S002
C.C. LOCK
FP-299
FLEXIBLE
XPHOTO_FREEZE
Hi8_MP
REC_PROOF
16 XEJECT_SW
14
14 KEY_AD5
ME/MP
15
HALL_COM
12
13
12 ZOOM_VR
T_REEL (-)
11
13 REG_GND
10
CN2404
PAGE 4-37
of LEVEL3
MODE_LED_VDD
T_REEL (+)
11 D_2.8V
SENSOR_VCC
9
9 XVTR_LED
S REEL (+)
8
10
7
B
VC-345 BOARD
(15/18)
8 XMEM_LED
S REEL (-)
7 XCAM_LED
REG_GND
6
CHARGE_LED_VDD
TAPE_LED (A)
5
6 XCHARGE_LED
TAPE_LED (K)
4
5
3
CN1009
PAGE 4-43
of LEVEL3
4 XPOWER_SW
TAPE_END (C)
D003
H001 3
T REEL
1 SENSOR 4
2
TAPE_TOP (C)
2
3 XMODE_SW
H002 3
S REEL
SENSOR
4
1
2
1
VC-345
(18/18)
CONTROL KEY BLOCK (SS-5100) is replaced as block,
so that PRINTED WIRING BOARD is omitted.
LND001
FP-301
FLEXIBLE
5
XX MARK:NO MOUNT
•
D001
TAPE LED
4
CONTROL KEY BLOCK
(SS-5100)
A
Q001
TAPE TOP
3
2 REG_GND
Q002
TAPE END
2
1 XS/S_SW
FP-802 FLEXIBLE
STATIC GND
FP-302
FLEXIBLE
05
4-50
3
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
4-2. SCHEMATIC DIAGRAMS
1
3
2
4
5
6
8
7
9
10
11
12
CONTROL KEY BLOCK (CF-5100)
A
XX MARK:NO MOUNT
•
CONTROL KEY BLOCK (CF-5100) is replaced as block,
so that PRINTED WIRING BOARD is omitted.
S022
B1
2
B
B2 4
S007
XX
R005
1200
S003
XX
1
A1
B1
2
B2 4
3 A2
1
B1
A1
3 A2
R013
2200
S012
XX
R009
1500
1
2
A1
B1
1
B2 4
3 A2
B2 4
2
R020
8200
R017
3900
S015
XX
B1
A1
3 A2
2
B2 4
S023
(PANEL_O/C_SW)
R022
27k
EASY
1
B1
A1
3 A2
2
1
4
3
B2
A1
A2
D002
EASY
BT001
LITHIUM
BATTERY
S016
C
R006
1200
S004
XX
R010
1500
S008
XX
R014
2200
S011
XX
S020
BACKLIGHT
R018
3900
R023
8200
LIGHT
S019
XX
S024
XX
REG_GND
1
N.C
B1
LI_3V
D_2.8V
R001 10k
B2
KEY_AD0
A1
2
1
4
3 A2
B1
2
B2 4
A1
B1
3 A2
B2
1
A1
2
1
4
3 A2
B1
2
1
B2 4
A1
B1
3 A2
2
1
A1
B1
3 A2
B2 4
2
1 A1
B2 4
3 A2
3 A2
R011
1500
S009
XX
R015
2200
S013
XX
R019
3900
S017
XX
R021
8200
S021
XX
B6
R007
1200
S005
XX
SW2 4
B2 4
XCUSTOM_LED_ON
S001
DSPL/BATT
INFO
SW1B 5
A1
1
SW1A 3
2
A1
B1
N.C
COM 2
D
S7
BATT_INFO
CUSTOM_LED_VDD
REG_GND
VC-345
(18/18)
XMS_LED
CN1007
PAGE 4-44
of LEVEL3
N.C
B1
D001
(MS ACCESS)
MS_LED_VDD
2
B2 4
R002 10k
1
A1
B1
2
B2 4
3 A2
1
A1
B1
3 A2
2
B2 4
1
B1
A1
3 A2
2
B2 4
1
A1
3 A2
B1
2
B2 4
1
A1
3 A2
KEY_AD1
D_2.8V
E
R003 10k
KEY_AD3
D_2.8V
KEY_AD2
R008
1200
S006
XX
R004
10k
DIAL_A
R012
1500
S010
XX
S014
XX
R016
2200
S018
XX
DIAL_B
B1
REG_GND
22
2
1
A1
B1
2
A1
B1 2
1 A1
B1
3 A2
B2 4
3 A2
B2 4
1
2
1
A1
XRESET
F
B1
2
1
B2 4
A1
3 A2
B2 4
3 A2
S002
4
B2
G
RESET
3
A2
LND025
CH GND
VC-345
(16/18)
PAGE 4-39
of LEVEL3
SIGNAL PATH
1
SP(+)
CN1008
2
SP901
SPEAKER
SP(-)
AUDIO
SIGNAL
H
PB
05
4-51
4-52
CF-5100
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
4-3. PRINTED WIRING BOARDS
Link
CD-472 BOARD
FP-792 FLEXIBLE BOARD
PD-205 BOARD
FP-228, FP-299, FP-300, FP-301, FP-302,
FP-802 FLEXIBLE BOARD
SI-041 BOARD
COMMON NOTE FOR PRINTED WIRING BOARDS
MOUNTED PARTS LOCATION
CIRCUIT BOARDS LOCATION
Board Name
Function
CD-472
PD-205
SI-041
CCD IMAGER
LCD DRIVE, BACKLIGHT DRIVE
STEADYSHOT, JACK
FLEXIBLE BOARDS LOCATION
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
4-3. PRINTED WIRING BOARDS
4-3. PRINTED WIRING BOARDS
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS
•
•
•
•
•
•
: Uses unleaded solder.
: Circuit board
: Flexible board
Pattern from the side which enables seeing.
: pattern of the rear side
(The other layers’ patterns are not indicated)
Through hole is omitted.
Circled numbers refer to waveforms.
There are a few cases that the part printed on diagram
isn’t mounted in this model.
C: panel designation
Board Name
Parts Location
CD-472
–
• Chip parts.
Transistor
B
Diode
6 5 4 4 5 6 5
C
E
4 4
1 2 3 3 2 1 1 2 3 3 2 1
1
3
3
1 23
2
1 2
1 2
1 3
4 3
4
1
2 3
4
4
3
3
4
5 4 3 3 4 5 2
1 2
1
4
3 2
1 1
2
2
1
3
4 6 5 4 4 5 6
2
1 1 2 3 3 2 1
2 2
Pattern
Total Number of Layers
Layers Not Indicated
8 layers
2 to 7 layers
PD-205
4-71
2 layers
–
SI-041
4-71
2 layers
–
FP-792 Flexible
–
1 layer
–
FP-228 Flexible
–
1 layer
–
FP-299 Flexible
–
1 layer
–
FP-300 Flexible
–
1 layer
–
FP-301 Flexible
–
1 layer
–
FP-302 Flexible
–
1 layer
–
FP-802 Flexible
–
1 layer
–
4-55
3
5
1 6 54
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
4-2. SCHEMATIC DIAGRAMS
4-3. PRINTED WIRING BOARDS
CD-472
Note for Printed Wiring Board (See page 4-55).
: Uses unleaded solder.
13
14
CD-472 BOARD
C953
R953
C
B
1
C952
E
Q951
C954
1
C951
2
R952
L951
5
7
2
3
R970
1
4
LND951
IC951
D951
R969
R968
C957
C955
7
8
14
6
8
9
1-860-937-
11
05
4-57
4-58
CD-472
Printed wiring boards of the VC-345 board are not shown.
Pages from 4-59 to 4-62 are not shown.
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
4-2. SCHEMATIC DIAGRAMS
4-3. PRINTED WIRING BOARDS
MOUNTED PARTS LOCATION
PD-205
Note for Printed Wiring Board (See page 4-55).
: Uses unleaded solder.
PD-205 BOARD
PIN007
C6011
L6003
1
Q6002
R6008
R6012
C6009
C6010
R6013
R6009
C6002
IC6001
12
8
9
3
7
T6001
20
FB6001
6
RB6001
CL6006 CL6005
6
C6018
C6015
PIN002
E
CL6002
B
G
R6022
C6017
D6001
C6016 R6021
CL6012
S
Q6008
Q6009
CL6008
C6014
1
1
R6001
D6002
D6004
C6028
D6003
PIN009
6
C6013
Q6006
R6002
PIN003
24
C6012
R6023
CL6011
R6029
Q6001
R6014
C6027
D
R6010
IC6002
CN6005
C
Q6005
R6028
1
PIN008
10
R6019
C6029
4
3
Q6004
6
CL6004
2
PIN004
R6018
C6025
5
1
1
C6006
25
24
13
2
A C6020 +
CN6001
B
4
5
2
3
6 5 4
1 2 3
R6005
37
36
4
Q6003
PIN005
PIN006
48
Note: Q6002 and Q6003 have the same mount location.
When replacing Q6002 or Q6003, please refer to
schematic diagram and electrical parts list.
2
1
3 4 5
FB6002
1
PIN001
L6001
5
R6030
+ C6019 A
R6026
C6022
C6005
C6001
C6004
D6006
LND605
C6003
1
A
C6007
E B
C
R6027
Q6007
L6002
10
1
R6011
C
CN6004
CN6007
CN6003
HF001
D
D6005
05
PD-205
1
2
4-63
3
1-860-939-
4
11
5
4-64
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
4-2. SCHEMATIC DIAGRAMS
4-3. PRINTED WIRING BOARDS
MOUNTED PARTS LOCATION
D001
(VIDEO LIGHT)
SI-041, FP-792 FLEXIBLE
Note for Printed Wiring Board (See page 4-55).
D002
(VIDEO LIGHT)
: Uses unleaded solder.
FP-792 FLEXIBLE BOARD
FP-792
1-8609291-860-929-
11
D003
(VIDEO LIGHT)
1
3
2
Note: CN751, CN752, D753, D754, IC751, J751 and J752 are
not included in SI-041 complete board.
SI-041 BOARD (SIDE B)
SI-041 BOARD (SIDE A)
5
7
4
3
LND765
A
A
J752
A/V
LND757
LND763
E
1
B
C
Q751
2
LND754
R759
D753
C754
C757
C752
R762
D753, 754
(IR EMITTER)
2
3
D754
B
CN751
DV
4
6
36
35
C758
SE751
(YAW)
1
SE752
(PITCH)
R763
1
3
3
D759
(TALLY)
R751
C755
3
4
4
C751
A
R755
2
1
R761
IC751
B
R752
R753
5
2
A
C753
6
1
1
FB751
3
CN752
C
5
4
D752
LF752
2
CN754
C
R754
D751
R760
C759
R764
LF751
R756
7
D756
(USB)
J751
R765
1
D755
C756
2
8
7
LND764
S VIDEO
3 2 1
D
4
6
1
2
3
5
R757
D
D760
VDR757
4
5
1
4
CN753
1-860-94105
1
2
3
4-65
4
1-860-941-
11
05
4
3
2
11
1
4-66
SI-041, FP-792
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
4-2. SCHEMATIC DIAGRAMS
4-3. PRINTED WIRING BOARDS
FP-228, FP-299, FP-300, FP-301, FP-302, FP-802 FLEXIBLE
Note for Printed Wiring Board (See page 4-55).
FP-300 FLEXIBLE (COMPONENT SIDE)
: Uses unleaded solder.
Q001
TAPE TOP
SENSOR
1-680-436-
1
15
11
1
FP-802 FLEXIBLE
(CONDUCTOR SIDE)
FP-299
FLEXIBLE
M902
CAPSTAN
MOTOR
15
15
1
S002
C.C. LOCK
D001
TAPE LED
S001
REC PROOF
o'
H001
T REEL
SENSOR
MR SENSOR
1
4
1-680-437-
DEW SENSOR
21
1-677-049-
S901
MODE
SWITCH
1
C
B
A
COM
1-680-434-
FP-228
FLEXIBLE
11
FP-301 FLEXIBLE
(CONDUCTOR SIDE)
11
FP-302 FLEXIBLE
(CONDUCTOR SIDE)
H002
S REEL
SENSOR
o'
11
1-689-290-
22
Q002
TAPE END
SENSOR
1-680-438-
11
4-67
FP-228, FP-299, FP-300, FP-301, FP-302, FP-802
4-68
Mounted parts location of the VC-345 board is not shown.
Pages 4-69 and 4-70 are not shown.
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
4-3. PRINTED WIRING BOARDS
no mark : side A
* mark : side B
4-4. MOUNTED PARTS LOCATION
PD-205 BOARD
SI-041 BOARD
C6001
C6002
C6003
C6004
C6005
C6006
C6007
C6009
C6010
C6011
C6012
C6013
C6014
C6015
C6017
C6018
C6019
C6020
C6028
C6029
A-2
B-2
A-3
A-2
A-2
B-3
A-4
B-2
B-2
A-5
C-4
C-4
C-3
C-2
C-2
C-2
A-3
B-3
C-4
C-2
CN6001
CN6003
CN6004
CN6005
CN6007
B-1
D-4
D-2
C-1
D-3
D6001
D6004
C-2
C-4
*
*
*
*
*
*
C758
C759
B-4
C-3
CN751
CN752
CN753
CN754
B-1
C-1
D-4
C-4
D751
D752
* D753
* D754
* D755
D756
D759
C-2
C-2
B-2
B-2
D-3
C-2
C-2
FB751
C-4
* IC751
C-2
* J751
* J752
D-2
A-1
Q751
A-2
IC6001 B-2
IC6002 C-2
*
*
R752
R753
R756
R757
R763
R764
R765
B-2
B-2
C-3
D-3
B-2
C-3
D-3
L6001
L6002
L6003
A-3
A-4
A-4
SE751
* SE752
B-3
B-3
Q6003
Q6004
Q6005
Q6006
Q6008
Q6009
A-4
C-2
C-2
C-3
C-3
C-3
R6005
R6009
R6010
R6012
R6013
R6014
R6019
R6021
R6022
R6023
R6030
RB6001
B-4
B-2
C-4
B-2
B-2
C-4
C-2
C-3
C-2
C-2
B-2
C-4
T6001
B-4
4-71E
PD-205, SI-041
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
NOTE
5. REPAIR PARTS LIST
NOTE: Characters A to L of the electrical parts list indicate location of exploded views in which the desired part is shown.
EXPLODED VIEWS
Link
A
OVERALL ASSEMBLY
B
FRONT PANEL BLOCK
E
LENS BLOCK
EVF BLOCK
G
BATTERY PANEL BLOCK
J
I
LS CHASSIS BLOCK ASSEMBLY
Link
D
LCD BLOCK
F
CABINET R BLOCK
CASSETTE COMPARTMENT
ASSEMBLY, DRUM ASSEMBLY
C
H
MD FRAME BLOCK
K
MECHANICAL CHASSIS
BLOCK ASSEMBLY-1
L
MECHANICAL CHASSIS
BLOCK ASSEMBLY-2
ELECTRICAL PARTS LIST
ACCESSORIES
CD-472 BOARD
C
FP-302 FLEXIBLE BOARD
J
PD-205 BOARD
D
FP-300 FLEXIBLE BOARD
J
FP-792 FLEXIBLE BOARD
B
SI-041 BOARD
B
FP-301 FLEXIBLE BOARD
J
FP-802 FLEXIBLE BOARD
J
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
5. REPAIR PARTS LIST
NOTE:
• -XX, -X mean standardized parts, so they may have some differences from
the original one.
• Items marked “*” are not stocked since they are seldom required for routine
service. Some delay should be anticipated when ordering these items.
• The mechanical parts with no reference number in the exploded views are not
supplied.
• Due to standardization, replacements in the parts list may be different from
the parts specified in the diagrams or the components used on the set.
• CAPACITORS:
uF: µF
• COILS
uH: µH
• RESISTORS
All resistors are in ohms.
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F: nonflammable
• SEMICONDUCTORS
In each case, u: µ, for example:
uA...: µA... , uPA... , µPA... ,
uPB... , µPB... , uPC... , µPC... ,
uPD..., µPD...
• Abbreviation
AUS : Australian model
CND : Canadian model
EE : East European model
NE : North European model
5-1
When indicating parts by reference number,
please include the board name.
The components identified by mark 0 or
dotted line with mark 0 are critical for safety.
Replace only with part number specified.
Les composants identifiés par une marque
0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
le numéro spécifié.
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
5. REPAIR PARTS LIST
5-1. EXPLODED VIEWS
5-1-1. OVERALL ASSEMBLY
6
EVF block
(See page 5-7.)
2
2
2
7
5
MD frame block
(See page 5-9.)
2
11
Battery panel block
(See page 5-8.)
2
3
2
10
8
2
4
9
Cabinet R block
(See page 5-6.)
2
ns
Front panel block
(See page 5-3.)
2 11
11
2
LCD block
(See page 5-5.)
Lens block
(See page 5-4.)
1
Ref. No.
Part No.
Description
1
2
3
4
5
X-3954-008-1
3-080-203-31
3-087-813-01
3-087-812-41
3-087-811-01
CABINET (C) (595) ASSY, P
SREW (M2), LOCK ACE, P2
COVER (51), JACK
SHEET (51), JACK
CABINET (UPPER) (51)
6
3-078-889-11 SCREW (M1.7)
Ref. No.
5-2
Part No.
Description
7
8
9
10
10
3-087-810-01
COUTION
3-079-012-01
3-087-831-21
3-087-831-31
LID (51), CPC
RETAINER (51), EVF FLEXIBLE
SCREW (30), TRIPOD
LABEL (51) (TRV360/TRV361)
LABEL (51) (TRV460/TRV460E/TRV461E)
11
3-080-204-21 SCREW, TAPPING, P2
CAUTION :
For the part of 8 : RETAINER (51), EVF FLEXIBLE
(3-088-616-01), cut WOVEN (T0.25), FABRIC NON
(3-076-631-01) into the desired length and use it.
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
5. REPAIR PARTS LIST
5-1-2. FRONT PANEL BLOCK
ns: not supplied
61
60
D002 D001
58
J752 D003
CN751
D753
58
ns
D754
CN752
SI-
04
1
IC751
J751
58
53
59
57
56
55
ns
54
58
ns
62
52
MIC901
51
(Note)
Ref. No.
Part No.
Description
51
52
53
54
55
3-087-738-11
3-087-740-01
X-3954-009-1
3-087-739-01
3-087-743-01
RETAINER (51), MICROPHONE
PLATE (51), MAGNIFICATION
PANEL (595) ASSY, FRONT
PLATE (51), NAME
SCREW (51), FILTER
56
57
58
59
60
3-087-742-01
3-087-749-01
3-080-204-21
A-7111-982-A
1-860-929-11
RING (51), FRONT
COVER (51), S TERMINAL
SCREW, TAPPING, P2
SI-041 BOARD, COMPLETE (Note)
FP-792 FLEXIBLE BOARD
61
62
3-087-994-01 CUSHION (51), JACK
3-088-031-01 CUSHION (51), MICROPHONE
Ref. No.
CN751
CN752
CN751, CN752, D753, D754, IC751, J751 and J752 are
not included in SI-041 complete board.
Part No.
Description
D001
D002
D003
1-794-276-11 CONNECTOR, SQUARE TYPE 4P (DV) (Note)
1-794-962-11 CONNECTOR, SQUARE TYPE (USB 5P) (USB)
(Note)
6-500-744-01 DIODE NSPW500BS-TL2 (VIDEO LIGHT)
6-500-744-01 DIODE NSPW500BS-TL2 (VIDEO LIGHT)
6-500-744-01 DIODE NSPW500BS-TL2 (VIDEO LIGHT)
D753
D754
IC751
J751
J752
8-719-078-24
8-719-078-24
6-704-975-01
1-778-518-11
1-778-040-11
DIODE DAC3825 (IR EMITTER) (Note)
DIODE DAC3825 (IR EMITTER) (Note)
IC RPM7240-V4 (Note)
CONNECTOR, EXTERNAL (S VIDEO OUT) (Note)
JACK, SMALL TYPE (A/V OUT) (Note)
MIC901 1-542-513-11 MICROPHONE
5-3
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
5. REPAIR PARTS LIST
5-1-3. LENS BLOCK
104
CD
105
-47
2
103
102
IC951
(Note)
101
(Note)
Ref. No.
101
102
103
104
Part No.
Description
8-848-765-01
1-758-554-11
3-053-973-01
A-7111-980-A
DEVICE, LENS LSV-820A
FILTER BLOCK, OPTICAL
RUBBER (W), SEAL
CD-472 BOARD, COMPLETE
Ref. No.
105
IC951
IC951
5-4
Be sure to read “Precuations for Replacement of CCD
Imager” on page 4-8 when changing the CCD imager.
Part No.
Description
3-080-204-21 SCREW, TAPPING, P2
A-7013-401-A CCD BLOCK ASSY (CCD IMAGER)
(TRV460E/TRV461E) (Note)
A-7016-724-A CCD BLOCK ASSY (CCD IMAGER)
(TRV360/TRV361/TRV460) (Note)
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
5. REPAIR PARTS LIST
5-1-4. LCD BLOCK
151
156
LCD901
ND901
152
153
5
-20
PD
154
155
The components identified by
mark 0 or dotted line with
mark 0 are critical for safety.
Replace only with part number specified.
Ref. No.
151
152
153
154
Les composants identifiés par une
marque 0 sont critiques pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
Part No.
Description
Ref. No.
Part No.
Description
X-3954-007-1
3-087-902-01
A-7111-981-A
3-080-204-21
CABINET (M) (595) ASSY, P
FRAME (61), PANEL
PD-205 BOARD, COMPLETE
SCREW, TAPPING, P2
155
156
LCD901
0 ND901
3-078-889-11
3-088-536-01
8-753-052-10
1-518-951-21
SCREW (M1.7)
CUSHION (61), LCD
ACX307AKM-1
TUBE, FLUORESCENT, COLD CATHODE
5-5
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
5. REPAIR PARTS LIST
5-1-5. CABINET R BLOCK
202
212
201
203
211
%
203
204
205
203
203
206
209
207
208
210
! : BT001
(BATTERY, LITHIUM SECONDARY)
Included in the control switch block (CF-5100).
Ref. No.
Part No.
Description
201
202
203
204
205
1-478-416-61
3-080-206-11
3-080-205-21
1-962-648-11
3-087-826-01
KEY BLOCK, CONTROL (CF-5100)
SCREW, TAPPING, P2
SCREW, TAPPING, P2
HARNESS (PD-124)
COVER (M) (51), HINGE
206
3-087-825-11 COVER (C) (51), HINGE
Ref. No.
5-6
Part No.
Description
207
208
209
210
211
3-078-889-11
1-478-418-11
X-3953-962-1
X-3954-005-1
CAUTION
SCREW (M1.7)
KEY BLOCK, CONTROL (PR-5100)
HINGE (51) ASSY
CABINET (R) (595) ASSY
TAPE (CF)
(TRV360/TRV460/TRV460E: E/TRV461E)
212
3-091-207-01 SHEET (CF), INSULATING
CAUTION :
For the part of 211 : TAPE (CF) (3-090-115-01), cut
WOVEN (T0.25), FABRIC NON (3-076-631-01) into
the desired length and use it.
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
5. REPAIR PARTS LIST
5-1-6. EVF BLOCK
ns: not supplied
251
253
254
255
252
254
ns
256
LCD902
ns
ns
257
258
Ref. No.
Part No.
Description
251
252
253
254
255
X-3953-982-1
X-3951-166-1
X-3953-966-1
3-080-204-21
X-3953-967-1
CABINET (UPPER) (587) ASSY, EVF
LENS (M) ASSY, VF
CABINET (LOWER) (515) ASSY, EVF
SCREW, TAPPING, P2
BASE (51) ASSY, SLDE
256
3-087-788-01 BASE (51), SLIDE
Ref. No.
Part No.
Description
257
3-080-203-31 SCREW (M2), LOCK ACE, P2
258
1-860-928-11 FP-797 FLEXIBLE BOARD
LCD902 1-805-465-61 INDICATOR MODULE LIQUID CRYSTAL
(TRV360/TRV361/TRV460)
LCD902 1-805-465-81 INDICATOR MODULE LIQUID CRYSTAL
(TRV460E/TRV461E)
5-7
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
5. REPAIR PARTS LIST
5-1-7. BATTERY PANEL BLOCK
ns: not supplied
ns
303
304
BT901
301
305
ns
302
302
302
302
306
307
Ref. No.
301
302
303
304
Part No.
Description
3-087-799-01
3-078-889-11
X-3954-006-1
3-072-305-01
SHEET METAL (LOWER) (51), STRAP
SCREW (M1.7)
PANEL (595) ASSY, BATTERY
LID (2500), JACK
Ref. No.
305
306
307
BT901
5-8
Part No.
Description
1-816-271-21
1-860-931-11
3-088-741-01
1-694-772-11
MEMORY STICK CONNECTOR 10P
FP-799 FLEXIBLE BOARD
SHEET (61), SHIELD
TERMINAL BOARD, BATTERY
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
5. REPAIR PARTS LIST
5-1-8. MD FRAME BLOCK
365
ns: not supplied
366
351
ns
352
367
364
ns
363
353
ns
362
354
365
Mechanism deck block
(See page 5-10 to 5-13.)
ns
355
355
355
356
355
355
357
Part No.
Description
351
352
353
354
355
1-478-417-41
3-080-253-01
X-3953-958-2
3-080-204-21
3-078-889-11
KEY BLOCK, CONTROL (SS-5100)
SCREW (M1.7), LOCK ACE, P2
FRAME (51) ASSY, CS
SCREW, TAPPING, P2
SCREW (M1.7)
356
357
358
359
3-066-169-01
3-087-809-01
1-860-927-11
A-7112-399-A
359
360
Ref. No.
361
SHEET (30), MD
FRAME (51), MD
FP-796 FLEXIBLE BOARD
VC-345 BOARD, COMPLETE (SERVICE)
(TRV360/TRV361)
A-7112-400-A VC-345 BOARD, COMPLETE (SERVICE)
(TRV460/TRV460E/TRV461E)
1-827-980-11 CABLE, FLEXIBLE FLAT (FFC-005)
5-9
361
359
358
Ref. No.
5
-34
VC
360
Part No.
Description
362
363
364
365
3-089-368-01 LABEL, FUSE REPLACEMENT (51)
(TRV360/TRV460)
X-3953-957-1 CABINET (L) (51) ASSY
3-978-765-01 SLIDER, G LOCK
3-087-802-01 BELT (51), GRIP
3-080-203-31 SREW (M2), LOCK ACE, P2
366
366
366
366
366
3-087-833-51
3-087-833-61
3-088-539-01
3-088-539-11
3-088-539-31
367
3-080-204-11 SCREW, TAPPING, P2
LABEL (L) (56) (TRV360)
LABEL (L) (56) (TRV361)
LABEL (L) (61) (TRV460)
LABEL (L) (61) (TRV460E)
LABEL (L) (61) (TRV461E)
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
5. REPAIR PARTS LIST
5-1-9. CASSETTE COMPARTMENT ASSEMBLY, DRUM ASSEMBLY
ns: not supplied
701
702
701
703
705
706
704
707
708
LS chassis block
assembly
(See page 5-11.)
M901
709
712
711
Mechanical chassis block
assembly
(See page 5-12 to 5-13.)
710
Ref. No.
Part No.
Description
701
702
703
704
705
3-065-932-01
3-065-895-01
3-065-896-01
X-3951-298-1
X-3951-302-1
PAN (2 MAIN M1.4X1.6), CAMERA
LEVER, REEL RELEASE
PLATE, BLIND
CASSETTE COMPARTMENT ASSY
DAMPER ASSY
706
707
X-3951-297-1 GEAR ASSY, R DRIVE
3-065-840-01 CUT (0.98X3X0.13), LUMILER (W)
Ref. No.
5-10
Part No.
Description
708
709
710
711
712
3-065-935-01
3-947-503-01
X-3951-299-1
3-074-309-01
7-624-101-04
HLC CUT 1.8X4X0.5
SCREW (M1.4)
SCREW ASSY, DRUM FITTING
ROLLER A, LS GUIDE
STOP RING 1.2 (E TYPE)
M901
A-7048-986-A DRUM (DKH-04B-R) (SERVICE)
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
5. REPAIR PARTS LIST
5-1-10. LS CHASSIS BLOCK ASSEMBLY
759
ns: not supplied
757
760
767
S001
764
766
758
768
763
769
765
770
761
762
756
771
755
772
781
752
S002
Q001
775
778
780
776
H001
779
774
FP-802
ns
H002
777
Q002
FP-301
ns
773
D001
FP-302
ns
FP-300
ns
ns
754
753
752
783
751
Ref. No.
Part No.
Description
Part No.
Description
751
752
753
754
755
3-065-822-02
3-947-503-01
A-7096-416-B
A-7096-415-A
A-7096-426-A
RAIL (S), GUIDE
SCREW (M1.4)
BASE (S) BLOCK ASSY, GUIDE
BASE (T) BLOCK ASSY, GUIDE
CHASSIS ASSY, LS
Ref. No.
771
772
773
774
775
3-065-830-01
X-3951-288-1
3-065-819-01
3-065-821-01
X-3951-289-1
SPRING, S RATCHET
TABLE (T) ASSY, REEL
SPRING, TG1 ARM
RAIL (T), GUIDE
TABLE (S) ASSY, REEL
756
757
758
759
760
3-065-802-01
A-7096-414-A
3-065-801-01
3-065-932-01
X-3951-303-1
SPRING, TG7 ARM
ARM BLOCK ASSY, TG7
RETAINER, TG7
PAN (2 MAIN M1.4X1.6), CAMERA
ARM ASSY, PINCH
776
777
778
779
780
3-065-833-01
3-065-831-01
X-3951-304-1
3-065-835-01
3-065-820-01
GUIDE, LOCK
PLATE (SPR), RE RETURN
ARM ASSY, TG1
GUIDE (S), CASSETTE
SPRING, RVS ARM
761
762
763
764
765
3-065-823-01
3-065-794-01
3-065-792-01
3-065-834-01
3-065-824-01
ARM, T RATCHET
ROAD (SPR), PINCH ARM
ROLLER, P LIM ARM
GUIDE (T), CASSETTE
SPRING, T RATCHET
781
783
D001
H001
H002
X-3951-296-1
3-067-167-01
8-719-988-42
8-719-033-37
8-719-033-37
BAND (ASSY), BT
SCREW (M1.4X2), CAMERA TAPPING
DIODE GL453 (TAPE LED)
ELEMENT, HALL HW-105C (T REEL)
ELEMENT, HALL HW-105C (S REEL)
766
767
768
769
770
A-7096-417-A
3-071-650-01
3-065-832-01
3-065-828-01
3-065-829-01
SOFT ASSY, T
SCREW (M1.7) (S)
PLATE, LS CAM
ARM, S RATCHET
PLATE, S RATCHET (RE)
Q001
Q002
S001
S002
8-729-907-25
8-729-907-25
1-692-614-11
1-572-688-11
PHOTO TRANSISTOR PT4850F (TAPE TOP)
PHOTO TRANSISTOR PT4850F (TAPE END)
SWITCH, PUSH (3 KEY) (REC PROOF)
SWITCH, PUSH LEVER (1 KEY) (C. C. LOCK)
5-11
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
5. REPAIR PARTS LIST
5-1-11. MECHANICAL CHASSIS BLOCK ASSEMBLY-1
ns: not supplied
816
811
805
815
819
824
ns
815
810
809
817
805
814
802
807
813
M902
812
815
802
821
820
M903
822
806
823
802
808
818
804
803
Mechanical chassis
block assembly-2
(See page 5-13.)
801
Ref. No.
Part No.
Description
Part No.
Description
801
802
803
804
805
A-7096-422-A
3-947-503-01
3-065-928-01
3-065-927-01
3-065-932-01
BASE ASSY, DRUM
SCREW (M1.4)
SPACER, GROUND
GROUND, DRUM
PAN (2 MAIN M1.4X1.6), CAMERA
Ref. No.
814
815
816
817
818
3-065-881-01
3-065-934-01
1-786-096-11
3-065-898-01
3-065-870-01
SPRING, P PRESSURE PLATE
HLW CUT 0.98X3X0.25
SWITCH, ROTARY
SPRING, EJECT ARM
ROLLER, LS GUIDE
806
807
808
809
810
3-067-154-01
3-065-931-01
X-3947-398-1
3-065-933-01
1-677-049-11
SPRING, CAPSTAN
RAIL (T2), GUIDE
SCREW ASSY, M1.7 PW
PAN (2 MAIN 1.4X4.5), CAMERA
FP-228 FLEXIBLE BOARD
819
820
821
822
823
A-7096-421-A
3-065-918-01
A-7096-419-A
3-065-902-01
3-065-905-01
ARM ASSY, HCL
GEAR (2), CAM RELAY
GEAR ASSY, CHANGE
BELT, TIMING
GEAR, RELAY
811
812
813
1-680-434-11 FP-299 FLEXIBLE BOARD
3-065-877-01 PLATE (T), GUIDE LOCK
X-3951-301-1 PLATE ASSY, PINCH PRESSURE
824
M902
M903
3-065-882-01 ARM, EJECT
8-835-701-01 MOTOR, DC SCE13A/C-NP (CAPSTAN)
A-7096-420-A MOTOR ASSY, LD (LOADING)
5-12
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
5. REPAIR PARTS LIST
5-1-12. MECHANICAL CHASSIS BLOCK ASSEMBLY-2
860
863
861
859
857
862
864
858
865
856
855
853
866
854
852
851
867
868
Ref. No.
Part No.
Description
851
852
853
854
855
3-065-920-01
3-065-913-01
3-065-914-01
3-065-917-01
3-065-934-01
ARM, HC DRIVE
GEAR (4), LD
SHEET, COVER
GEAR (1), CAM RELAY
HLW CUT 0.98X3X0.25
856
857
858
859
3-065-915-01
3-065-878-01
3-065-932-01
A-7096-413-A
GEAR (1), CAM
PLATE (S), GUIDE LOCK
PAN (2 MAIN M1.4X1.6), CAMERA
GEAR (S) ASSY, GUIDE
Ref. No.
5-13
Part No.
Description
860
861
862
863
864
7-624-101-04
A-7096-412-A
X-3951-307-1
X-3951-305-1
3-065-901-01
STOP RING 1.2 (E TYPE)
GEAR (T) ASSY, GUIDE
PLATE ASSY, M SLIDE
ARM ASSY, LS
ROLLER, LS ARM
865
866
867
868
3-065-916-01
3-065-919-01
X-3951-308-1
X-3951-300-2
GEAR (2), CAM
ARM, T1 LIMITTER
ARM ASSY, GL
CHASSIS ASSY, MECHANICAL
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
CD-472
FP-300
FP-301
FP-302
FP-792
FP-802
PD-205
5-2. ELECTRICAL PARTS LIST
Ref. No.
Part No.
Description
Ref. No.
A-7111-980-A CD-472 BOARD, COMPLETE
**********************
(IC951 is not included in this complete board.)
D002
D003
Part No.
6-500-744-01 DIODE NSPW500BS-TL2 (VIDEO LIGHT)
6-500-744-01 DIODE NSPW500BS-TL2 (VIDEO LIGHT)
< CAPACITOR >
C951
C953
C955
1-126-395-11 ELECT CHIP
1-128-994-21 ELECT CHIP
1-164-360-11 CERAMIC CHIP
FP-802 FLEXIBLE BOARD (Not Supplied)
********************
22uF
47uF
0.1uF
20%
20%
16V
10V
16V
< HOLE ELEMENT >
H001
H002
< CONNECTOR >
CN951
IC951
8-719-033-37 ELEMENT, HALL HW-105C (T REEL)
8-719-033-37 ELEMENT, HALL HW-105C (S REEL)
1-815-762-11 CONNECTOR, FFC/FPC 14P
< SWITCH >
< IC >
IC951
S001
S002
A-7013-401-A CCD BLOCK ASSY (CCD IMAGER) (Note)
(TRV460E/TRV461E)
A-7016-724-A CCD BLOCK ASSY (CCD IMAGER) (Note)
(TRV360/TRV361/TRV460)
1-692-614-11 SWITCH, PUSH (3 KEY) (REC PROOF)
1-572-688-11 SWITCH, PUSH LEVER (1 KEY) (C.C. LOCK)
A-7111-981-A PD-205 BOARD, COMPLETE
**********************
< COIL >
L951
1-469-528-91 INDUCTOR
< CAPACITOR >
100uH
2SC4178-F14
C6001
C6002
C6003
C6004
C6005
1-125-777-11
1-125-837-91
1-164-943-11
1-164-943-11
1-164-943-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
1uF
0.01uF
0.01uF
0.01uF
10%
10%
10%
10%
10%
10V
6.3V
16V
16V
16V
82
3.3K
0
C6006
C6007
C6009
C6010
C6011
1-164-943-11
1-115-566-11
1-125-777-11
1-164-739-11
1-164-657-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
4.7uF
0.1uF
560PF
0.015uF
10%
10%
10%
5%
1%
16V
10V
10V
50V
50V
C6012
C6013
C6014
C6015
C6017
1-125-777-11
1-100-371-11
1-115-566-11
1-107-826-11
1-165-908-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
12PF
4.7uF
0.1uF
1uF
10%
5%
10%
10%
10%
10V
3.15KV
10V
16V
10V
C6018
C6019
C6020
C6028
C6029
1-107-826-11
1-104-847-11
1-100-502-11
1-162-966-11
1-100-252-11
CERAMIC CHIP
TANTALUM CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
22uF
3.3uF
0.0022uF
0.1uF
10%
20%
20%
1%
10%
16V
4V
25V
50V
6.3V
< TRANSISTOR >
Q951
8-729-117-73 TRANSISTOR
< RESISTOR >
R952
R953
R970
1-218-940-11 RES-CHIP
1-218-959-11 RES-CHIP
1-216-864-11 SHORT CHIP
5%
5%
1/16W
1/16W
FP-300 FLEXIBLE BOARD (Not Supplied)
********************
< PHOTO TRANSISTOR >
Q001
8-729-907-25 PHOTO TRANSISTOR PT4850F (TAPE TOP)
FP-301 FLEXIBLE BOARD (Not Supplied)
********************
< DIODE >
D001
< CONNECTOR >
CN6001
CN6003
CN6004
CN6005
CN6007
8-719-988-42 DIODE GL453S (TAPE LED)
FP-302 FLEXIBLE BOARD (Not Supplied)
********************
D6001
D6004
8-729-907-25 PHOTO TRANSISTOR PT4850F (TAPE END)
1-860-929-11 FP-792 FLEXIBLE BOARD
********************
(D001, D002 and D003 are not included in this flexible board.)
< DIODE >
D001
6-500-744-01 DIODE NSPW500BS-TL2 (VIDEO LIGHT)
Note: Be sure to read “Precautions for Replacement of
CCD Imager” on page 4-8 when changing the
CCD imager.
1-794-997-11
1-764-709-11
1-815-031-11
1-816-176-11
1-816-176-11
PIN, CONNECTOR 20P
FFC/CONNECTOR, FPC (LIF) 10P
CONNECTOR, FFC/FPC (ZIF) 24P
FFC/CONNECTOR, FPC (ZIF) 6P
FFC/CONNECTOR, FPC (ZIF) 6P
< DIODE >
< PHOTO TRANSISTOR >
Q002
Description
5-14
8-719-050-42 DIODE RD3.3UM-T1B
8-719-073-01 DIODE MA111-(K8).S0
< IC >
IC6001
IC6002
8-752-115-66 IC CXA3622BR-T4
6-704-149-01 IC TK11128CSCL-G
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
PD-205
Ref. No.
Part No.
Description
Ref. No.
Part No.
< COIL >
L6001
L6002
L6003
1-469-527-91 INDUCTOR
1-412-056-11 INDUCTOR
1-428-878-11 INDUCTOR
6-550-083-01
8-729-054-48
8-729-054-48
8-729-041-23
8-729-054-89
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
Q6009
8-729-054-44 TRANSISTOR
Description
< FERRITE BEAD >
47uH
4.7uH
82uH
FB751
1-414-760-21 INDUCTOR, FERRITE BEAD
< IC >
< TRANSISTOR >
Q6003
Q6004
Q6005
Q6006
Q6008
SI-041
IC751
TPC6C01 (TE85R)
UP04601008S0
UP04601008S0
NDS356AP
UP04211008S0
6-704-975-01 IC RPM7240-V4
< JACK >
J751
J752
1-778-518-11 CONNECTOR, EXTERNAL (S VIDEO)
1-778-040-11 JACK, SMALL TYPE (A/V)
< TRANSISTOR >
UP04111008S0
Q751
8-729-023-22 TRANSISTOR
2SD2114K
< RESISTOR >
< RESISTOR >
R6005
R6009
R6010
R6012
R6013
1-216-824-11
1-218-975-11
1-218-969-11
1-208-707-11
1-208-935-11
METAL CHIP
RES-CHIP
RES-CHIP
METAL CHIP
METAL CHIP
1.8K
68K
22K
10K
100K
5%
5%
5%
0.5%
0.5%
1/10W
1/16W
1/16W
1/16W
1/16W
R6014
R6019
R6021
R6022
R6023
1-218-949-11
1-218-965-11
1-218-977-11
1-218-965-11
1-216-847-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
METAL CHIP
470
10K
100K
10K
150K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/10W
R6030
1-218-949-11 RES-CHIP
470
5%
1/16W
R752
R753
R756
R757
R763
1-216-806-11
1-216-806-11
1-216-864-11
1-216-864-11
1-216-821-11
METAL CHIP
METAL CHIP
SHORT CHIP
SHORT CHIP
METAL CHIP
R764
R765
1-216-833-11 METAL CHIP
1-216-833-11 METAL CHIP
56
56
0
0
1K
5%
5%
1/10W
1/10W
5%
1/10W
10K
10K
5%
5%
1/10W
1/10W
< SENSOR >
SE751
SE752
1-476-807-41 SENSOR, ANGULAR VELOCITY (YAW)
1-476-807-31 SENSOR, ANGULAR VELOCITY (PITCH)
< COMPOSITION CIRCUIT BLOCK >
RB6001 1-234-369-21 RES, NETWORK 10 x 4 (1005)
< TRANSFORMER >
0 T6001
Electrical parts list of the VC-345 board is
not shown.
Pages 5-16 to 5-24 are not shown.
1-435-786-31 TRANSFORMER, INVERTER
A-7111-982-A SI-041 BOARD, COMPLETE
**********************
(CN751, CN752, D753, D754, IC751, J751 and J752 are not included in this
complete board.)
< CAPACITOR >
C758
C759
1-127-760-11 CERAMIC CHIP
1-127-760-11 CERAMIC CHIP
4.7uF
4.7uF
10%
10%
6.3V
6.3V
< CONNECTOR >
CN751
CN752
CN753
CN754
1-794-276-11
1-794-962-11
1-816-232-11
1-818-074-11
CONNECTOR, SQUARE TYPE 4P (DV)
CONNECTOR, SQUARE TYPE (USB 5P) (USB)
PIN, CONNECTOR (PC BOARD) 4P
CONNECTOR, FFC/FPC (ZIF) 36P
< DIODE >
D751
D752
D753
D754
D755
6-500-044-01
6-500-044-01
8-719-078-24
8-719-078-24
8-719-421-27
DIODE
DIODE
DIODE
DIODE
DIODE
DF6A6.8FU (TE85R)
DF6A6.8FU (TE85R)
DAC3825 (IR EMITTER)
DAC3825 (IR EMITTER)
MA728
D756
D759
6-500-044-01 DIODE DF6A6.8FU (TE85R)
6-500-506-01 DIODE TLRMV1021 (T15SOY, F) (TALLY)
5-15
The components identified by
mark 0 or dotted line with
mark 0 are critical for safety.
Replace only with part number specified.
Les composants identifiés par une
marque 0 sont critiques pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
Checking supplied accessories.
USB cable (1)
1-823-931-21
AC-L15A/L15B AC Adaptor (1)
0 1-477-533-32 (TRV461E)
0 1-477-533-51
(EXCEPT TRV461E)
Shoulder strap (1)
3-987-015-01
Other accessories
Battery holder
3-083-973-01
Wireless Remote Commander
RMT-831 (1)
1-477-898-41
(EXCEPT TRV461E)
1-477-898-61 (TRV461E)
Lens cap (1)
X-3952-971-1
Cap string (1)
3-979-194-12
Rechargeable battery pack
NP-FM30 (1)
0 A-7096-387-A (US, CND)
0 A-7096-388-B
(EXCEPT US, CND)
Memory Stick 8MB (1)
21-pin adaptor (1)
1-770-783-21
(AEP, UK, NE, EE)
Conversion 2P adaptor (1)
0 1-569-008-12
(TRV361: E, TRV460: E,
TRV461: E)
A/V connecting cable (1)
1-824-097-41
CD-ROM
(SPVD-012 (V) USB Driver) (1)
3-086-790-01 (US, CND)
(SPVD-012 USB Driver) (1)
3-087-821-01
(EXCEPT US, CND)
Power cord (1)
0 1-696-819-21 (AUS)
0 1-769-608-11 (AEP, NE, EE, E)
0 1-783-374-11 (UK)
0 1-790-542-12 (US, CND)
CAMERA OPERATIONS GUIDE
3-087-921-11 MANUAL, INSTRUCTION (ENGLISH)
(TRV360/TRV361/TRV460)
3-087-921-21 MANUAL, INSTRUCTION (FRENCH) (TRV460: CND)
3-087-921-31 MANUAL, INSTRUCTION (SPANISH, PORTUGUESE)
(TRV361/TRV460: E)
3-087-921-41 MANUAL, INSTRUCTION (TRADITIONAL CHINESE)
(TRV460: E)
3-087-923-11 MANUAL, INSTRUCTION (ENGLISH)
(TRV460E: AEP, UK, E, AUS/TRV461E)
3-087-923-21 MANUAL, INSTRUCTION (FRENCH) (TRV460E: AEP, E)
3-087-923-31 MANUAL, INSTRUCTION (SPANISH, PORTUGUESE)
(TRV460E: AEP)
3-087-923-41 MANUAL, INSTRUCTION (ITALIAN, GREEK)
(TRV460E: AEP)
3-087-923-51 MANUAL, INSTRUCTION (GERMAN, DUTCH)
(TRV460E: AEP)
3-087-923-61 MANUAL, INSTRUCTION (SWEDISH, RUSSIAN)
(TRV460E: NE)
3-087-923-71 MANUAL, INSTRUCTION (DANISH, FINNISH)
(TRV460E: NE)
3-087-923-81 MANUAL, INSTRUCTION (POLISH, CZECH) (TRV460E: EE)
3-087-923-91 MANUAL, INSTRUCTION (HUNGALIAN, SLOVAKIAN)
(TRV460E: EE)
3-087-924-11 MANUAL, INSTRUCTION (ARABIC, PERSIAN)
(TRV460E: E/TRV461E)
3-087-924-31 MANUAL, INSTRUCTION (SIMPLIFIED CHINESE)
(TRV460E: E)
COMPUTER APPLICATIONS GUIDE
3-087-936-11 MANUAL (PC), INSTRUCTION (ENGLISH)
(EXCEPT TRV460E: AEP, NE, EE)
3-087-936-21 MANUAL (PC), INSTRUCTION (FRENCH)
(TRV460: CND/TRV460E: AEP, E)
3-087-936-31 MANUAL (PC), INSTRUCTION (GERMAN, DUTCH)
(TRV460E: AEP)
3-087-936-41 MANUAL (PC), INSTRUCTION (SPANISH, PORTUGUESE)
(TRV361/TRV460: E/TRV460E: AEP)
3-087-936-51 MANUAL (PC), INSTRUCTION (ITALIAN, GREEK)
(TRV460E: AEP)
3-087-936-61 MANUAL (PC), INSTRUCTION (SWEDISH, RUSSIAN)
(TRV460E: NE)
3-087-936-71 MANUAL (PC), INSTRUCTION (DANISH, FINNISH)
(TRV460E: NE)
3-087-936-81 MANUAL (PC), INSTRUCTION (POLISH, CZECH)
(TRV460E: EE)
3-087-936-91 MANUAL (PC), INSTRUCTION (HUNGALIAN, SLOVAKIAN)
(TRV460E: EE)
3-087-937-11 MANUAL (PC), INSTRUCTION (ARABIC, PERSIAN)
(TRV460E: E/TRV461E)
3-087-937-21 MANUAL (PC), INSTRUCTION (TRADITIONAL CHINESE)
(TRV460: E)
3-087-937-31 MANUAL (PC), INSTRUCTION (SIMPLIFIED CHINESE)
(TRV460E: E)
The components identified by
mark 0 or dotted line with
mark 0 are critical for safety.
Replace only with part number specified.
5-25E
Les composants identifiés par une
marque 0 sont critiques pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
DCR-TRV360/TRV361/TRV460/TRV460E/TRV461E
9-876-293-31
Sony EMCS Co.
— 48 —
2003L0500-1
©2003.12
Published by DI Customer Center
[Description of main button functions on toolbar of the Adobe Acrobat Reader Ver5.0 (for Windows)]
Toolbar
Printing a text
Reversing the screens displayed once
1. Click the Print button
.
2. Specify a printer, print range, number of copies, and other options, and then click [OK].
• To reverse the previous screens (operation) one by one, click
.
the
• To advance the reversed screens (operation) one by one, click
the
.
Application of printing:
To set a range to be printed within a page, select the graphic
and drag on the page to enclose a range to
selection tool
be printed, and then click the Print button.
Application to the Service Manual:
This function allows you to go and back between circuit diagram and printed circuit board diagram, and accordingly it
will be convenient for the voltage check.
Finding a text
1. Click the Find button
.
2. Enter a character string to be found into a text box, and click
the [Find]. (Specify the find options as necessary)
Application to the Service Manual:
To execute “find” from current page toward the previous pages,
select the check box “Find Backward” and then click the
“Find”.
Moving with link
1. Select either palm tool
, zoom tool
, text selection tool
, or graphic selection tool
.
2. Place the pointer in the position in a text where the link exists
(such as a button on cover and the table of contents page, or
blue characters on the removal flowchart page or drawing
page), and the pointer will change to the forefinger form
.
3. Then, click the link. (You will go to the link destination.)
Moving with bookmark:
Click an item (text) on the bookmark pallet, and you can move
to the link destination. Also, clicking
can display the
hidden items.
(To go back to original state, click
)
3. Open the find dialog box again, and click the [Find Again] and
you can find the matched character strings displayed next.
(Character strings entered previously are displayed as they are
in the text box.)
Application to the Service Manual:
The parts on the drawing pages (block diagrams, circuit diagrams, printed circuit boards) and parts list pages in a text
can be found using this find function. For example, find a
Ref. No. of IC on the block diagram, and click the [Find Again]
continuously, so that you can move to the Ref. No. of IC on
the circuit diagram or printed circuit board diagram successively.
Note: The find function may not be applied to the Service
Manual depending on the date of issue.
Zooming or rotating the screen display
“Zoom in/out”
• Click the triangle button in the zoom control box to select the
display magnification. Or, you may click
ing in or out.
or
for zoom-
Switching a page
• To move to the first page, click the
.
• To move to the last page, click the
.
• To move to the previous page, click the
• To move to the next page, click the
.
.
“Rotate”
• Click rotate tool
, and the page then rotates 90 degrees each.
Application to the Service Manual:
The printed circuit board diagram you see now can be changed
to the same direction as the set.
Reverse
987629331.pdf
Revision History
Ver.
Date
1.0
2003.12
History
Official Release
Contents
—
S.M. Rev.
issued
—