Download Maintenance Manual Change Tracking

Service Documents > Maintenance Manual Change Tracking
Maintenance Manual Change Tracking
Date
2008.12.06
Status
Index
Rev.
7.2.1
Added
1.0
New item [Y Drive Belt Noise] was added.
7.2.2
Added
1.0
New item [Media Attachment to the Platen] was added.
Date
2008.09.17
Index
Status
Rev.
1.1.1
Revised
1.10
[Indication on LCD] “DPC”  “PDC”
Revised
1.10
[Indication on LCD] “V1.00”  “V1.00.0”
Added
1.10
Step 6:
Revised
1.10
[Indication on LCD] “DPC”  “PDC”
Revised
1.10
[Indication on LCD] “V1.00”  “V1.00.0”
Added
1.10
Step 4:
“When the fuse F13 of the main PCB assy is blown, ...”
Added
1.10
Step 5:
“(Except firmware update)”
Added
1.10
Step 4:
“(Only when MAIN power is on)”
Added
1.10
Step 5:
“(Refer to “1.1.6 Operation for Connecting the Heads”)”
Revised
1.10
Step 2, 4: “When it cannot be detected ...”
 “When detection is impossible or the number of pinch rollers is not recognized, ...”
Added
1.10
Tips Box: “(Only during Step 3 above)”
1.1.5
Revised
1.10
Tips Box: “[PRINT MODE]  [CUT MODE] was switched.”
 “The machine draws a stored pattern which can be selected ...”
1.1.8
Added
1.10
Tips Box: “In service mode, the buzzer sounds ...”
1.2.3
Added
1.10
Step 3:
1.2.9
Revised
1.10
[Indication on LCD]: All the indications on the display revised
Revised
1.10
Description of status No1-1: “... near full or more.”  “... full or more.”
Erased
1.10
Step 2:
Revised
1.10
Important Box: “... is cumulatively counted in this unit.”
 “... is not cumulatively counted in this unit.”
1.3.2
Revised
1.10
In Table: “Execution status when an error occurs” (5, 6, 7, 8)
1.3.6
Revised
1.10
In Table: “Ink consumption through one supply path”
1.3.9
Erased
1.10
Item: “Selection of model”
2.1.1
Revised
1.10
“Connection Diagram Inside the Main Body” revised
2.3.1
Added
1.10
Volume specification: “Type”
Added
1.10
Fuse rating
2.3.2
Added
1.10
Fuse rating
2.3.6
Revised
1.10
List of connectors CN7: “AUX.”  “P Head Lock Solenoid”
2.3.7
Revised
1.10
List of connectors CN19: “Debug Monitor”  “Not equipped”
“CPLD writing”  “AUX.”
Revised
1.10
List of connectors CN21: “X-axis Motor”  “AUX.”
Revised
1.10
List of connectors CN14: “Debug Connector”  “None”
Added
1.10
List of connectors CN14: “AUX.”
Revised
1.10
List of connectors CN2: “For CPLD writing”  “None”
Added
1.10
List of connectors CN2: “AUX.”
Revised
1.10
Item: “Cartridge Assy”  “Print Head Unit Assy”
1.1.2
1.1.3
1.1.4
2.3.8
2.3.11
3.1.1
Manual Ver.
1.20
Remark
Changes
Manual Ver.
1.10
Remark
Changes
“When the fuse F13 of the main PCB assy is blown, ...”
“Press [FUNCTION], and the maintenance washing liquid ...”
“The [!WASTE TANK] is displayed in LOCAL mode.”
WWW.SERVICE-MANUAL.NET
© 2009 MIMAKI ENGINEERING CO.,LTD.
Maintenance Manual Change Tracking P.3