Download INSTALLATION MANUAL

4. SELECTING AN INSTALLATION LOCATION
4.1. Dimensions and Name of parts
23
(7/8)
63.5 (2-1/2)
45.3 (1-13/16)
120 (4-3/4)
(d) (e)
30 (1-3/16) 33 (1-5/16)
17 (11/16)
(c)
(f) (g) (h) (i)
15.3 (5/8)
Hole: 9 × 4.5
(3/8 × 3/16)
120 (4-3/4)
(a) (b)
Unit: mm (in.)
Hole: 6 × 4.5
(1/4 × 3/16)
83.5 (3-5/16)
Remote controller unit
Hole: 12.5 × 4.5
(1/2 × 3/16)
(a) Display panel
(b) On/Off button:
It is possible to operate only while displaying the “Monitor Mode Screen”.
(c) LED lamp (Operation indicator)
Status Icons
Error
Emergency stop
Forced Stop
Under maintenance
Mode mismatch
Filter sign
Defrost operation
Oil recovery operation
Central controlled
Operation prohibited
Child locked
Part locked
Conducting electricity
Anti freeze operation
Test run
Economy Setting is
enabled
Set Temp. Range Setting is
enabled
Auto Off Timer is enabled
On Timer Setting is
enabled
Off Timer Setting is
enabled
Weekly Timer Setting is
enabled
Set Temp. Auto Return
Setting is enabled
Master remote controller
Operation controlled
Remote controller sensor
is enabled
(d) [MODE] button: Set the operation mode. Refer to operating manual.
4.2. Setting the room temperature detection location
(e) [MENU] button
(f) [+],[-] buttons (Set temperature buttons):
Set the operating temperature on “Monitor Mode Screen”. Refer to
operating manual. Used to setting in setting screen.
[<],[>] buttons: Used to setting in setting screen.
(g) [FAN] button: Set the fan speed. Refer to operating manual.
(h) [ENTER] button
(i) Room temperature sensor (inside)
Screen display
Monitor Mode Screen
(j)
(k)
(l)
(m)
Setting Screen
(Ex. Airflow direction setting)
CAUTION
As the temperature sensor of remote controller detects the temperature near the wall, when there is a certain difference between the room
temperature and the wall temperature, the sensor will not detect the
room temperature correctly sometimes. Especially when the outer side
of the wall on which the sensor is positioned is exposed to the open air,
it is recommended to use the temperature sensor of the indoor unit to
detect the room temperature when the indoor and outdoor temperature
difference is significant.
The detection location of the room temperature can be selected from the 2 methods
at the right. Choose the detection location
that is best for the installation location.
The temperature sensor of the indoor unit
or the remote controller can be used to
detect the room temperature.
A sensor of the indoor unit
(inside)
A sensor of the remote
controller (inside)
(n)
(o)
“Monitor Mode Screen” is the home screen of this unit. Except for in the
following cases, the screen will go back to the “Monitor Mode Screen” if
there is no operation for over 10 min. (Unsaved settings will be cancelled.)
• In Menu 2 settings
(j) Operation mode indicator: Refer to operating manual.
Auto
Cool
Dry
Fan
Heat
(k) Temperature indicator: Refer to operating manual.
(l) Fan speed indicator: Refer to operating manual.
(m) When “8.8. The Setting of Using the Current Time” is set to “0: Not
used” , display is not performed.
If using the remote control sensor, setting is required. Refer to “8.7.
Remote Controller Sensor Setting”.
4.3. Installation space
• This product cannot be installed in wall.
• Recommendation installation height of the remote controller is 1.4 m (55
in.) (from the floor surface to the bottom of the remote controller).
• Even when you install a remote controller to one of a switch box and the
surface of a wall, secure the space shown in following figure. When there
is insufficient space, there may be remote controller sensor misdetections and remote controller removal may be difficult.
(n) Airflow direction indicator: Refer to operating manual.
30 (2) or
more
(o) Menu types indicator:
Menu settings *1
Menu 1 settings *1
Menu 2 settings
*1: Concerning setting details and methods, please refer to the OPERATING MANUAL on the CD-ROM.
30 (2)
or more
Unit: mm (in.)
30 (2)
or more
220 (9)
or more
* Please secure enough space where a flat-blade screwdriver to take off a
case can be inserted.
En-2
9373328261-01_IM.indb 2
1/8/2014 1:56:09 PM