Download User's Manual

1.6.
CONFIGURATION NAVIGATION DIAGRAM /1 (hereafter "Navigation Diagram")
ROOT
Stnd.
Stat.
PAr*.
AL.
vErs
rSET
SP
ALrb
LOAd
dE *
In*
In'*
CJ
ConF./ StAt/
[7]=1
dELo
m-SP
dEHi
ALbL
dInP
P.Edt
Pid*
ALbH
mmi2
rLbL
rLbH
mmi3
mmi4
mmi5
mmi6
Int
dEr
rLbH
mrES
dZon
ConF./SYSt/
mmi2[2
Ctr*
Conf./SYSt/
mmi2[3
rEGL
rEDH
Conf./SYSt/
mmi2[1
Src.S
Conf./PrG/
Opt[7]=1
ALSP
GAin
ALbH
rLbL
dInP
dFLt
mmiE
ALhY
PrG
cGn
OPt
Yt.
cYt
Yt and cYt in case ConF./Cnt*/SEt[6]=1
appear, otherwise all of the PID groups
ConF./Cnt*/Yt and ConF./Cnt*/cYt are valid by
ConF./Cnt*/SEt[54]=xx
ConF./PrG/
SEt[10]
SSP*
ConF./PrG/
dEcL[54]
EvnL
EvnH
Cnt*
It is essential for
the appearing a
control block that:
SPLo≠SPHi
PrFL
SttS
Conf./PrG/
dEF[43]
h/Y
SPHi
cYHi
c-hY
2nIn
sEc
ucLb
SEt
dEcL
OPt
SPLo
Yd’
YLo
YHi
H-hY
cYt
cYLo
dAy
rtc
dEF
Yt.
rEG*
EvnL
EvnH
PrEt
Sont
dEF
SEt
dEcL
Src.E
dSt.S
OPCd
PrG
mmi1
mSP1
ALr*
ALbL
SYSt
mSP2
mSP3
mSP4
Y*
ALrb
ConF.
h/m
dAY
StAt
mont
YEAr
ALr*
dEF
SEt
LGE*
LGA*
dEcL
OPt
SOFt
WArn
uGn*
Abstract of the parameters in root:
Stnd. query the system data
query the digital inputs
overwrite the counters
program writing and query the program data
Stat. logging the 4 PID channel PV-SP max-min data
PAr*. the values of the SP-s chosen from digital inputs
PID* parameter setting
manual reset for P and PD controllers
dead-zone set
actuator cycle time set (PWM)
relative cool gain set in HEAT-COOL control
relative cool actuator cycle time set (PWM)
AL. query the ALARM state (it can be seen in Stnd. page too)
setting the ALARM SP and hysteresis
ConF./ALr*/
OPt[54]
rtc
sEc
h/m
dAY
mont
YEAr
Note The * replaces an ordinal (hexa):
0, 1, 2, 3, 4, 5, 6, 7, 8, 9, A, b, C, d, E, F,G
6
ALdt
AHdt
ALSP
ALHY
rtc
Com*
dEF
SEt
Addr
oSP1