Download USER MANUAL

USER MANUAL
CTEK BATTERY CHARGER MXS I 0
FOR ALL TYPES OF LEAD-ACID BATTERIES
2YIAR
WARRANTY
fUUY AUTOMAJIC
...z
...Q
...
...
Di:
Ill
!::
....
z
...
Ill
~
Q
0
z
u::
CHARGING
CONGRATULATIONS
to the purchase of your new professional switch mode battery chorger.
This charger is included in o series of professional chargers from CTEK SWEDEN AB ond
represents the latest technology in battery charging.
SUPPLY PLUG •
MAINS CABLE
1. Connect the charger to the battery.
2.Connect the charger lo the woll socket. The power lamp will indicate that the mains
cable is connected to the wall socket. The error lomp will indicate if the battery clomps
ore incorrectly connected. The reverse polarity protection will ensure that the battery
or charger will not be damaged.
3 , Press the MODE-button to se lect charging program.
4. Fallow lhe 8-step display through the charging process.
The battery is ready to start the engine when STEP 4 is lit.
The battery is fully charged when STEP 7 is lit.
5. Stop charging at any time by disconnecting the mains coble from the wall socket.
Ju;:l==J/=1~
READY TO USE
FULLY CHARGED
CTEK COMFORT CONNECT - eyelet MB
CTEK COMFORT CONNECT - damp
•Supply plug• may cfiffH to suit your wa ll tocket.
© Attach the te mpe rature
1e n1or
to the charge r.
@ Atta ch the tem perature H n sor to the clomp .
TEMPERATURE
SENSOR
INDICATOR
NORMAL
BATTERY
PROGRAM
AGM
BATTERY
PROGRAM
RECOND
PROGRAM
SUPPLY
PROGRAM
EN • 3
flll
~
CHARGING PROGRAMS
ERROR LAMP
Sellings are made by pressing the MODE-bullan. After about two seconds the charger
activa tes the selected program. The selected program will be restarted next time the
charger is connected.
If the error lamp is lit, check the following:
The table e x plains the different Char ging Programs:
Batter
.
1mm1•11111~!..lltt'ftlh.J.
Normal batte ry program
14.4V/10A. Use for WET batteries,
Co/Co, MF and for most GEL batteries
AGM battery progrom 14.7V/10A
Use for AGM batteries.
i
-2o· c-+so·c
(·4°f-122°F)
3. Has char g ing b e en In t errupte d in STEP 1, 2 o r 5?
Restart the charger by pressing the MODE-bullon. If charging is still
being interrupted, the battery...
STEP 1: ...is seriosly sulphated ond ma y need to be replace d.
STEP 2 : ... con not accept charge and may need lo be replaced.
STEP 5: ...con not keep charge and may need lo be replaced .
(·4°F-122°f)
POWER LAMP
Recond p rogrom 15.8V/1.5A
-2o·c-+so·c
If the power lamp is lit with a:
Use to return energy to the empty
(-4°f-122°F)
-
1. STEADY LIGHT
The mains cable is connected lo the wall sodcet.
2. FLASHING LIGHT1
The charger hos enlefed the ~ 10Ve mode. This happens ii the
charger isn ·1connected lo the botlery in 2 minutes
~·---
your battery once per yeor ond ofter
deep dischore to maximise lifetime
20-300Ah
2. 11 the chare•r connect9cl to a 12V battery?
1-2o·c-+so•c
WET and Co/Co batteries. Recond
RECOND
11
1. Is the chargers pos itive lead connected to the batterys
positive pole ?
and capacity. The Recond program
odds STEP 6 to the n o rmol bott e ry
prog ram. frequent use of the Recond
program may cause waler loss in the
batteries and reduce service life of
TEMPERATURE SENSOR
electronics. Contocl your vehicle and
battery supplier for advice.
E
Ii\.
m
4 • EN
Supply program 13.6V/10A
.2o·c-+so·c
Use as 12V power supply or use for
(·4°f-122°F)
Root maintenance charging when 100%
capacity of the battery is required.
Supply program activates step 7 wilhout
time or voltage limitation.
T~'(• sp~r~ p'U'l~~~~~~?~)o'''-~'Y chory1._•r
is
d,sobiC"d dur1n9 SUPPLY program
The MXS 10 is equipped with on external temperature se nsor. The temperature sensor is attachable. If so, the charger will compensate voltage accor·
ding to ambient temperature. Activoted temperature sensor will be indicated
by a lit temperature sensor indicator lamp.
READY TO USE
Ii'
m
The table shows the estimated lime for empty batte ry lo 80% charge
BATTERY SIZE (Ah)
TIME TO 80% CHARGED
20Ah
2h
50Ah
5h
100Ah
10h
200Ah
20h
CHARGING PROGRAM
DlSULPHATION
sonSTART
IUUC
ABSORPTION
ANALYSE
l.ECOND
FLOAT
PULSE
1
i
~
.j
g
..
l
STEP 1 DESULPHATION
Detects sulphoted botteries. Pulsing current ond voltoge, removes sulphote from the leod
plotes of the bottery restoring the bottery copocity.
STEP 2 SOFT START
Tests if the bottery con occept chorge. This step prevents thot chorging proceeds with o
defecl bollery.
STEP3 BULK
Chorging with moximum current until opproximotely 80% battery capacity.
STEP 4 ABSORPTION
Charging with declining current to maximize up to 100% bottery capacity.
'
STEP S ANALYSE
Tests if the ballery can hold c harge. Batterie• that can not hold charge may need tobe re placed.
STEP 6 RECOND
Choose the Recond program to add the Recond step to the charging proce"! During the Recond step
voltage increases to creote controlled gosing in the ballery. Gosing mixe• the bollery ocid ond gives
back eneruy to the bottery.
STEP 7FLOAT
Mointoining the bottery voltoge ot moximum level by providing o constont voltoge chorge.
STEP 8 PULSE
Mointoining the bottery ot 95-100% copocity. The chorger monitors the battery voltoge ond gives a
pulse when nece„ory to keep the bottery fully chorged.
EN • 5
CONNECT THE CHARGER TO A BATTERY
TECHNICAL SPECIFICATIONS
INFO
lf the battery clamps ore incorrectly con·
nected, the reverse polority protection
will ensure that the battery ond charger
ore not damaged .
f o r batt• rle1 mo unted ln1lde o vehlcle
1. Connect the ted clomp lo the bollery's
positive pole.
2 . Connect the block cfomp to the vehicle cltos·
sis remote lrom the luel p ipe ond the boltery.
3 . Connecf the chorger to the wofl socket.
4 . Oisconnecf the chorger lrom the woll socket
b.fore disconneding the hottery.
5. Oisconnecf '"• bloclc clomp before the red
clomp.
Som• ve hicfe a may flave poaitiva ly
e arthad batte rie s .
f. Connecf fhe block clomp to the bottery's
negative pole.
2 . Connecl the red clomp lo the vehicle chossis
remole from the fuel p ipe ond the boftery.
3 . Connect the chorger to the woll socket
4 . Oisconnecf the chorger from the woll socket
before disconnecfing the boltery.
5 . Oisconnecf the red clomp b efore the block
domp.
@
6 • EN
Cha..... lllOClel
MXS 10
Model number
1046
aatH Voltage AC
220- 2.olOVAC, 50-60Hz
Chorging voltage
ltartvektip
2.(N
lfil l4.4V, AeM
l4.7V, HCOND l5.8V, I
Charging curre nt
lOA mox
Curnnt, maln•
1.0A rms (at fvff chorging current)
lack curre nt drain'
<l Ah/month
111pp1e· ·
<4%
Ambient
te mpe rature
„
Ull'll'U'
l3.6V
·20'C to +SO'C, output power is reduced
outomoticolly ot high temperoture1
Char9er type
Eight step, fvlly outomatic chorging cyde
latte ry type1
All types ol l2V leod-ocid botteries
(WET, Mf, Co/Co, AGM ond GEL)
lattery capaclty
20 - 200Ah up to 300Ah for molntenance
Dimen1ion1
197 x 93 x 49mm (l x W x HI
lnsulatlan daP
IP65
Weight
0 .8kg
') Bock currenl drein is the currenl thot droins the bottery il the chorger is not connected
lo the moins. CTEK chorgers hos o very low bock currenl.
" JThe quolity ol the chorging volto9e ond chorging current is very importonl. A high
current ripple heots up the bottery which hos an oging ellect on the positive electrode.
High voltoge ripple could horm other equipment thot is connected to the bottery. CTEK
bottery chorgers produce very clean voltoge ond current with low ripple.
SAFETY
LIMITED WARRANTY
• The charger is designed lor charging 12V lead-acid batteries. Do not use the charger
lor ony other purpose.
Check the charger coble s prior to use. Ensure that no crocks have occurred in the
cables or in the bend protection. A chorger with domoged cables must not be used.
A do moge coble must be reploced by o CTEK represento tive.
• Never charge a damaged battery.
• Never charge a frozen battery.
Never place the charger on top of the battery when charging.
Always provide lor proper ventilation during charging.
Avoid covering the chorger.
A battery being charged could emit explosive gasses. Prevent sporks close to the
bollery. When botte ries are reaching the end ol their lifecycle internol sporks may occur.
All batteries fail sooner or later. A battery that fails during charging is normally
taken care of by the chargers odvonced control, but some rare errors in the battery
could still exist. Don't leove ony bottery during charging unattend ed lor a langer period
oflime.
• Ensure that the cabling does not jam or comes into contoct with hot surfaces or sharp
edges.
CTEK SWEDEN AB, issues this limited worronty to the original purchoser of this product.
This limited wo rro nty is not transferable. The warranty opplies to monufocturing Faults
ond ma terial defects lor 2 yeors from the dote of purchose. The customer must return the
product together with the re ce ipt of purchose to the point of purcho se. This wo rronty is
void if the bottery charger ha s been opened, hondled co relessly or repoire d by onyone
other thon CTEK SWEDEN AB or its outhorised representotives. O ne ol the screw holes
in the bottom of the chorger is seo led. Removing or domoging the seol will void the
worronty. CTEK SWEDEN AB mo kes no worronty other thon this limited worronty ond
is not lioble for ony other costs other thon those mentioned obove, i.e. no consequentiol
do moges. Moreover, CTEK SWEDEN AB is not obligoted to ony other wo rronty other
thon this worronty.
• Battery acid is corrosive. Rinse immediotely with water if ocid comes into contact
SUPPORT
CTEK offers o professionol custom support: www.ctek.com.
For lotest revised user manual see www.ctek.com. By e-mail: [email protected],
by telerhone: +46(0) 225 351 80, by lax +46(0) 225 351 95.
By moi: CTEK SWEDEN AB, Rostugnsvägen 3, SE-776 70 VIKMANSHYTIAN,
SWEDEN.
VIKMANSHYTIAN, SWEDEN 2011-09-01
with skin or eyes, seek immediate medicol odvice.
• Always check that the charger has switched to STEP 7 before leaving the charger
unattended and connected for long periods. lf the charger has not switched to STEP 7
within 55 hours, this is an indication af an error. Ma nually disconnect the chorger.
Batteries consume woter during use and charging. For bolleries where woter con
be odded, the wate r level should be checked regularly. lf the water level is low a dd
distilled water.
This appliance is not de signed lor use by young children or people who connot reod
or understond the mo nual unless they a re under the supervision ol o responsible person
ta ensure thot they con use the battery chorger sofely. Store ond use the bottery chorger
out of the reoch of children, ond ensure thot children connot ploy with the chorger.
Connection to the moins supply must be in accordonce with the national regulotions
lor electricol installotions.
/'h r
/~-
__,..
Bengt Hagander, President
CTEK SWEDEN AB
EN • 7
~
t::ll.