Download AT8020: IPMI Sensor User Guide

Transcript
Sens
or ID
47
48
49
50
Sensor Name
/ Entity (ID)
FRU0 IPMBL State
/ PICMG Front Board
(160.96 )
FRU1 IPMBL State
/ PICMG Front Board
(160.96 )
FRU2 IPMBL State
/ PICMG Front Board
(160.96 )
FRU3 IPMBL State
/ PICMG Front Board
(160.96 )
Event/Reading Type
(Class and Code)
/ Sensor Type (Code)
(Discrete 0x6f)
/ OEM IPMBL Link
State ( 0xc3)
(Discrete 0x6f)
/ OEM IPMBL Link
State ( 0xc3)
(Discrete 0x6f)
/ OEM IPMBL Link
State ( 0xc3)
(Discrete 0x6f)
/ OEM IPMBL Link
State ( 0xc3)
Description
52
(Discrete 0x6f)
/ Processor ( 0x07)
[7:6] - 00b = unspecified byte 2
01b = previous state and/or severity in byte 2
10b = OEM code in byte 2
11b = sensor-specific event extension code in byte 2
[5:4] - 00b = unspecified byte 3
01b = reserved
10b = OEM code in byte 3
11b = sensor-specific event extension code in byte 3
[3:0] - Offset from Event/Reading Code for discrete event state
02h (bit 2): IPMB-L Disable
03h (bit 3): IPMB-L Enable
[7:6] - 00b = unspecified byte 2
01b = previous state and/or severity in byte 2
10b = OEM code in byte 2
11b = sensor-specific event extension code in byte 2
[5:4] - 00b = unspecified byte 3
01b = reserved
10b = OEM code in byte 3
11b = sensor-specific event extension code in byte 3
[3:0] - Offset from Event/Reading Code for discrete event state
00h (bit 0): S0 / G0 “working”
[7:6] - 00b = unspecified byte 2
01h (bit 1): S1 “sleeping with system h/w & processor
01b = previous state and/or severity in byte 2
context maintained”
10b = OEM code in byte 2
02h (bit 2): S2 “sleeping, processor context lost”
11b = sensor-specific event extension code in byte 2
03h (bit 3): S3 “sleeping, processor & h/w context
[5:4] - 00b = unspecified byte 3
lost, memory retained.”
01b = reserved
04h (bit 4): S4 “non-volatile sleep / suspend-to disk”
10b = OEM code in byte 3
05h (bit 5): S5 / G2 “soft-off”
11b = sensor-specific event extension code in byte 3
06h (bit 6): S4 / S5 soft-off, particular S4 / S5 state [3:0] - Offset from Event/Reading Code for discrete event state
Advance Configuration cannot be determined
and Power Interface 07h (bit 7): G3 / Mechanical Off
08h (bit 8): Sleeping in an S1, S2, or S3 states (used
State
when particular S1, S2, S3 state cannot be
determined)
09h (bit 9): G1 sleeping (S1-S4 state cannot be
determined)
0Ah (bit 10): S5 entered by override
0Bh (bit 11): Legacy ON state
0Ch (bit 12): Legacy OFF state
0Eh (bit 13): Unknown
General health status,
Aggregation of critical
(Discrete 0x03)
sensor. This list is
/ Platform Alert ( 0x24)
flexible and could be
adjust based on
customer requirements.
CPU 0 ThermTrip
/ PICMG Front Board
(160.96 )
02h (bit 2): IPMB-L Disable
03h (bit 3): IPMB-L Enable
#N/A
Health Error
/ PICMG Front Board
(160.96 )
54
[7:6] - 00b = unspecified byte 2
01b = previous state and/or severity in byte 2
10b = OEM code in byte 2
11b = sensor-specific event extension code in byte 2
[5:4] - 00b = unspecified byte 3
01b = reserved
10b = OEM code in byte 3
11b = sensor-specific event extension code in byte 3
[3:0] - Offset from Event/Reading Code for discrete event state
IPMB-L branch from
FRU2 fault detection
sensor
(Discrete 0x6f)
/ System ACPI Power
State ( 0x22)
(Discrete 0x6f)
/ Processor ( 0x07)
02h (bit 2): IPMB-L Disable
03h (bit 3): IPMB-L Enable
IPMB-L branch from
FRU1 fault detection
sensor
ACPI State
/ PICMG Front Board
(160.96 )
CPU 0 Status
/ PICMG Front Board
(160.96 )
Data Byte 1
[7:6] - 00b = unspecified byte 2
01b = previous state and/or severity in byte 2
10b = OEM code in byte 2
11b = sensor-specific event extension code in byte 2
[5:4] - 00b = unspecified byte 3
01b = reserved
10b = OEM code in byte 3
11b = sensor-specific event extension code in byte 3
[3:0] - Offset from Event/Reading Code for discrete event state
IPMB-L branch from
FRU0 fault detection
sensor
51
53
Offset
02h (bit 2): IPMB-L Disable
03h (bit 3): IPMB-L Enable
CPU 0 Status
CPU 0 ThermTrip
00h (bit 0): State Deasserted
01h (bit 1): State Asserted
Data Byte 3
Bit[7:3]: Always 0
Bit[2:0]:
0h = No failure
1h = Unable to drive clock HI
2h = Unable to drive data HI
3h = Unable to drive clock LO
4h = Unable to drive data LO
5h = clock low timeout
6h = Under test (the IPM Controller is
attempting to
determine who is causing a bus hang)
7h = Undiagnosed Communication Failure
Always 0
Bit[7:3]: Always 0
Bit[2:0]:
0h = No failure
1h = Unable to drive clock HI
2h = Unable to drive data HI
3h = Unable to drive clock LO
4h = Unable to drive data LO
5h = clock low timeout
6h = Under test (the IPM Controller is
attempting to
determine who is causing a bus hang)
7h = Undiagnosed Communication Failure
Always 0
Bit[7:3]: Always 0
Bit[2:0]:
0h = No failure
1h = Unable to drive clock HI
2h = Unable to drive data HI
3h = Unable to drive clock LO
4h = Unable to drive data LO
5h = clock low timeout
6h = Under test (the IPM Controller is
attempting to
determine who is causing a bus hang)
7h = Undiagnosed Communication Failure
Always 0
Bit[7:3]: Always 0
Bit[2:0]:
0h = No failure
1h = Unable to drive clock HI
2h = Unable to drive data HI
3h = Unable to drive clock LO
4h = Unable to drive data LO
5h = clock low timeout
6h = Under test (the IPM Controller is
attempting to
determine who is causing a bus hang)
7h = Undiagnosed Communication Failure
[7:4] - Optional offset from ‘Severity’ Event/Reading Code. FFh
(0Fh if unspecified).
[3:0] - Optional offset from Event/Reading Type Code for
previous discrete event state. (0Fh if unspecified.)
[7:6] - 00b = unspecified byte 2
01b = previous state and/or severity in byte 2
10b = OEM code in byte 2
11b = sensor-specific event extension code in byte 2
[5:4] - 00b = unspecified byte 3
01b = reserved
10b = OEM code in byte 3
11b = sensor-specific event extension code in byte 3
[3:0] - Offset from Event/Reading Code for discrete event state
00h (bit 0): IERR
[7:6] - 00b = unspecified byte 2
01h (bit 1): Thermal Trip
01b = previous state and/or severity in byte 2
02h (bit 2): FRB1/BIST failure
10b = OEM code in byte 2
03h (bit 3): FRB2/Hang in POST failure (used hang
11b = sensor-specific event extension code in byte 2
is believed to be due or related to a processor failure. [5:4] - 00b = unspecified byte 3
Use System Firmware Progress sensor for other
01b = reserved
BIOS hangs.)
10b = OEM code in byte 3
04h (bit 4): FRB3/Processor Startup/Initialization
11b = sensor-specific event extension code in byte 3
failure (CPU didn’t start)
[3:0] - Offset from Event/Reading Code for discrete event state
05h (bit 5): Configuration Error
06h (bit 6): SM BIOS ‘Uncorrectable CPU-complex
Error’
07h (bit 7): Processor Presence detected
08h (bit 8): Processor disabled
09h (bit 9): Terminator Presence Detected
0Ah (bit 10): Processor Automatically Throttled
(processor throttling triggered by a hardware-based
mechanism operating independent from system
software, such as automatic thermal throttling or
throttling to limit power consumption.)
0Bh (bit 11): Machine Check Exception
(Uncorrectable)
0Ch (bit 12): Correctable Machine Check Error
FFh
00h (bit 0): IERR
[7:6] - 00b = unspecified byte 2
01h (bit 1): Thermal Trip
01b = previous state and/or severity in byte 2
02h (bit 2): FRB1/BIST failure
10b = OEM code in byte 2
03h (bit 3): FRB2/Hang in POST failure (used hang
11b = sensor-specific event extension code in byte 2
is believed to be due or related to a processor failure. [5:4] - 00b = unspecified byte 3
Use System Firmware Progress sensor for other
01b = reserved
BIOS hangs.)
10b = OEM code in byte 3
04h (bit 4): FRB3/Processor Startup/Initialization
11b = sensor-specific event extension code in byte 3
failure (CPU didn’t start)
[3:0] - Offset from Event/Reading Code for discrete event state
05h (bit 5): Configuration Error
06h (bit 6): SM BIOS ‘Uncorrectable CPU-complex
Error’
07h (bit 7): Processor Presence detected
08h (bit 8): Processor disabled
09h (bit 9): Terminator Presence Detected
0Ah (bit 10): Processor Automatically Throttled
(processor throttling triggered by a hardware-based
mechanism operating independent from system
software, such as automatic thermal throttling or
throttling to limit power consumption.)
0Bh (bit 11): Machine Check Exception
(Uncorrectable)
0Ch (bit 12): Correctable Machine Check Error
[7:4] - Optional offset from ‘Severity’ Event/Reading Code. FFh
(0Fh if unspecified).
[3:0] - Optional offset from Event/Reading Type Code for
previous discrete event state. (0Fh if unspecified.)
21
AN09004
Data Byte 2
Always 0
FFh
[7:4] - Optional offset from ‘Severity’ Event/Reading Code. FFh
(0Fh if unspecified).
[3:0] - Optional offset from Event/Reading Type Code for
previous discrete event state. (0Fh if unspecified.)
AT8020: Sensor User Guide v1.0