Download Snapper 3538 User's Manual

ATTACHMENT
ILLUSTRATED
PARTS LIST
ATTACHMENT
Mfg. No. Description
1694148
Lift Lever Kit
MANUFACTURING, INC.
500 N Spring Street / PO Box 997
Port Washington, WI 53074-0997 USA
www.simplicitymfg.com
© Copyright 2002 Simplicity Manufacturing, Inc.All Rights Reserved.
Rev. 0 9/2002
TP 400-3538-00-AT-SMA
Lift Lever KIt
986030
NOTE: Unless noted otherwise,
use the standard hardware torque
specification chart.
25
3
Torque to
23-28 ft. lbs.
(31-38 Nm)
2
4
5
1
6
Rotate clockwise
as far as possible
before tighting.
7
8
9
24
23
22
21
20
18
11
19
10
12
10
17
14
16
15
8
13
16
29
28
26
16
27
Assemble into
lower hole of Ref. Item 20.
R Side View
Mower
Lift Arm
30
The above parts group applies to the following Mfg. Nos.:
1694148 Lift Lever Kit
© Copyright 2002 Simplicity Manufacturing, Inc. All Rights Reserved.
2
TP 400-3538-00-AT-SMA
Lift Lever KIt
REF NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
PART NO.
QTY.
1927557
1931333
1722291
1723124
1960518
1723321
1721581
1926149
1721712
1960636
1722482
1722112
156302
1723163
1723795
1919381
1921160
1722819
1960033
1721654
1935255
1675232
1723499
1722357
1724378
1707514
1930570
1919438
1724432
1931277
2
4
1
1
1
1
1
6
1
5
1
1
1
1
1
7
1
1
1
1
1
1
1
1
1
2
2
2
2
4
DESCRIPTION
NUT, Flange, 5/16-18
CARRIAGE BOLT, 5/16-18 x 3/4
GRIP, Lift Lever
BUTTON, Red Nylon, for 1/4 Rod
NUT, Push
SPRING, Compression, Lift Lever
QUADRANT, Lift, Powdered Metal
CAPSCREW, 5/16-18 x 1, G8
LEVER ASSEMBLY, Lift
NUT, Hex, 5/16-18
ROD, Latch
LOCK, Lift, Powdered Metal
SPRING, Extension
SPACER, 1/2 x 3/4 x 23/32
BAR, Lift Link
WASHER, 5/16, Black
CAPSCREW, Hex Head, 5/16-18 x 2-1/4
PIN, Flat Head, 1/2 x 2-1/8
CLIP, Hair Pin, 2-9/16 Long
SHAFT ASSEMBLY, Lift
NUT, Speed, 5/16-18, Lug
SPRING, Extension
RETAINER, Spring Flat
CAPSCREW, Hex Head, 5/16-18 x 4-1/2
COVER, Hand Control
CHAIN, 3-Link
CAPSCREW, Hex Head, 5/16-18 x 1-1/2
NUT, Nylock, 5/16-18
ARM, Lift, Duel, Mower
NUT, Whizlock, 5/16-18
Footnotes:
The above parts group applies to the following Mfg. Nos.:
1694148 Lift Lever Kit
TP 400-3538-00-AT-SMA
3
Hardware Identification & Torque Specifications
Common Hardware Types
Torque Specification Chart
Hex Head Capscrew
FOR STANDARD MACHINE HARDWARE (Tolerance ± 20%)
Washer
Hardware
Grade
Lockwasher
Carriage Bolt
No
Marks
SAE Grade 2
Hex Nut
Size Of
Hardware
Standard Hardware Sizing
8-32
8-36
10-24
10-32
1/4-20
1/4-28
5/16-18
5/16-24
3/8-16
3/8-24
7/16-14
7/16-20
1/2-13
1/2-20
9/16-12
9/16-18
5/8-11
5/8-18
3/4-10
3/4-16
7/8-9
7/8-14
1-8
1-12
When a washer or nut is identified as 1/2”, this is the
Nominal size, meaning the inside diameter is 1/2 inch; if a
second number is present it represent the threads per inch
When bolt or capscrew is identified as 1/2 - 16 x 2”, this
means the Nominal size, or body diameter is 1/2 inch; the
second number represents the threads per inch (16 in this
example, and the final number is the body length of the
bolt or screw (in this example 2 inches long).
The guides and ruler furnished below are designed to
help you select the appropriate hardware and tools.
0
1/4
Nut, 1/2”
1/2
Inside
Diameter
3/4
1
1/4
1/2
3/4
Screw, 1/2 x 2
2
1/4
Body
Diameter
in/lbs
ft/lbs
19
20
27
31
66
76
11
12
20
23
30
35
50
55
65
75
90
100
160
180
140
155
220
240
Nm.
2.1
2.3
3.1
3.5
7.6
8.6
15.0
16.3
27.2
31.3
40.8
47.6
68.0
74.8
88.4
102.0
122.4
136
217.6
244.8
190.4
210.8
299.2
326.4
SAE Grade 5
in/lbs
ft/lbs
30
31
43
49
8
10
17
19
30
35
50
55
75
90
110
120
150
180
260
300
400
440
580
640
SAE Grade 8
Nm.
in/lbs
ft/lbs
Nm.
3.4
3.5
4.9
5.5
10.9
13.6
23.1
25.8
40.8
47.6
68.0
74.8
102.0
122.4
149.6
163.2
204.0
244.8
353.6
408.0
544.0
598.4
788.8
870.4
41
43
60
68
12
14
25
27
45
50
70
80
110
120
150
170
220
240
386
420
600
660
900
1,000
4.6
4.9
6.8
7.7
16.3
19.0
34.0
34.0
61.2
68.0
95.2
108.8
149.6
163.2
204.0
231.2
299.2
326.4
525.0
571.2
816.0
897.6
1,244.0
1,360.0
NOTES
1. These torque values are to be used for all hardware
excluding: locknuts, self-tapping screws, thread forming
screws, sheet metal screws and socket head setscrews.
2. Recommended seating torque values for locknuts:
a. for prevailing torque locknuts - use 65% of grade 5
torques.
b. for flange whizlock nuts and screws - use 135% of
grade 5 torques.
3. Unless otherwise noted on assembly drawings, all torque
values must meet this specification.
1/2
Body
Length
3/4
3
1/4
1/2
3/4
4
Wrench & Fastener Size Guide
1/4
5/16
3/8
1/4” Bolt or Nut
Wrench—7/16”
5/16” Bolt or Nut
Wrench—1/2”
3/8” Bolt or Nut
Wrench—9/16”
7/16
DIA.
7/16” Bolt or Nut
Wrench (Bolt)—5/8”
Wrench (Nut)—11/16”
1/2
DIA.
1/2” Bolt or Nut
Wrench—3/4”