Download Snapper 2385 User's Manual
Transcript
Attachment Illustrated Parts List MANUFACTURING, INC. 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 USA © Copyright 2000 Simplicity Manufacturing, Inc.All Rights Reserved. Rev. 11/2000 TP 400-2385-00-AT-SMA Lift Lever - Lift Lever 984905 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 1 2 7 26 3 4 5 16 15 12 8 13 9 14 11 10 10 13 12 The above parts group applies to the following Mfg. Nos.: 1692623 Lift Lever - Regent © Copyright 2000 Simplicity Manufacturing, Inc. All Rights Reserved. 2 TP 400-2385-00-AT-SMA Lift Lever - Regent REF NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 PART NO. 1650157 1713995 1704718 1934953 1667286 1657648 1667290 1704715 1674669 1919438 1704716 1921977 1675795 1665591 1921719 1927609 QTY. 1 1 1 1 1 1 1 1 1 4 1 4 2 1 1 1 DESCRIPTION BUTTON GRIP LEVER ASSEMBLY PUSH NUT, 5/16 SPRING LATCH, Lift Lever ROD BRACKET SPACER LOCKNUT, 5/16-18 SPACER CAPSCREW, Hex Head 5/16-18 x 1-1/4 SPACER QUADRANT, Lift CAPSCREW, Hex Head, 3/8-18 x 2-1/2 ROLL PIN, 3/8 x 1 Footnotes: The above parts group applies to the following Mfg. Nos.: 1692623 Lift Lever - Regent TP 400-2385-00-AT-SMA 3 Hardware Identification & Torque Specifications Common Hardware Types Torque Specification Chart Hex Head Capscrew FOR STANDARD MACHINE HARDWARE (Tolerance ± 20%) Washer Hardware Grade Lockwasher Carriage Bolt No Marks SAE Grade 2 Hex Nut Size Of Hardware Standard Hardware Sizing 8-32 8-36 10-24 10-32 1/4-20 1/4-28 5/16-18 5/16-24 3/8-16 3/8-24 7/16-14 7/16-20 1/2-13 1/2-20 9/16-12 9/16-18 5/8-11 5/8-18 3/4-10 3/4-16 7/8-9 7/8-14 1-8 1-12 When a washer or nut is identified as 1/2”, this is the Nominal size, meaning the inside diameter is 1/2 inch; if a second number is present it represent the threads per inch When bolt or capscrew is identified as 1/2 - 16 x 2”, this means the Nominal size, or body diameter is 1/2 inch; the second number represents the threads per inch (16 in this example, and the final number is the body length of the bolt or screw (in this example 2 inches long). The guides and ruler furnished below are designed to help you select the appropriate hardware and tools. 0 1/4 Nut, 1/2” 1/2 Inside Diameter 3/4 1 1/4 1/2 3/4 Screw, 1/2 x 2 2 1/4 Body Diameter in/lbs ft/lbs 19 20 27 31 66 76 11 12 20 23 30 35 50 55 65 75 90 100 160 180 140 155 220 240 Nm. 2.1 2.3 3.1 3.5 7.6 8.6 15.0 16.3 27.2 31.3 40.8 47.6 68.0 74.8 88.4 102.0 122.4 136 217.6 244.8 190.4 210.8 299.2 326.4 SAE Grade 5 in/lbs ft/lbs 30 31 43 49 8 10 17 19 30 35 50 55 75 90 110 120 150 180 260 300 400 440 580 640 SAE Grade 8 Nm. in/lbs ft/lbs Nm. 3.4 3.5 4.9 5.5 10.9 13.6 23.1 25.8 40.8 47.6 68.0 74.8 102.0 122.4 149.6 163.2 204.0 244.8 353.6 408.0 544.0 598.4 788.8 870.4 41 43 60 68 12 14 25 27 45 50 70 80 110 120 150 170 220 240 386 420 600 660 900 1,000 4.6 4.9 6.8 7.7 16.3 19.0 34.0 34.0 61.2 68.0 95.2 108.8 149.6 163.2 204.0 231.2 299.2 326.4 525.0 571.2 816.0 897.6 1,244.0 1,360.0 NOTES 1. These torque values are to be used for all hardware excluding: locknuts, self-tapping screws, thread forming screws, sheet metal screws and socket head setscrews. 2. Recommended seating torque values for locknuts: a. for prevailing torque locknuts - use 65% of grade 5 torques. b. for flange whizlock nuts and screws - use 135% of grade 5 torques. 3. Unless otherwise noted on assembly drawings, all torque values must meet this specification. 1/2 Body Length 3/4 3 1/4 1/2 3/4 4 Wrench & Fastener Size Guide 1/4 5/16 3/8 1/4” Bolt or Nut Wrench—7/16” 5/16” Bolt or Nut Wrench—1/2” 3/8” Bolt or Nut Wrench—9/16” 7/16 DIA. 7/16” Bolt or Nut Wrench (Bolt)—5/8” Wrench (Nut)—11/16” 1/2 DIA. 1/2” Bolt or Nut Wrench—3/4”