Download Korg MICROX X50 User's Manual

73: Limit–M.Dly
d
(Limiter – Multitap Delay)
This effect combines a mono-type limiter and a multitap
delay. You can change the order of the effect connection.
e
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Left
Wet / Dry
Routing
f
Multitap Delay
Limiter
Feedback
+
Limiter
Delay
Mt.Dly Wet / Dry
Right
[LMT] Ratio
Sets the signal compression ratio
a
G.Adj (Gain Adjust)
Sets the limiter output gain
c
–15...+15dB
[CMP] Sensitivity
Sets the sensitivity
1...100
☞ Fx:02
Attack
Sets the attack level
1...100
☞ Fx:02
Level (Output Level)
Sets the compressor output level
0...100
☞ Fx:02
h
(Source)
Selects the modulation source of the effect balance
Off...Tempo
(Amount)
Sets the modulation amount of the effect balance
–100...+100
1.0:1...50.0:1, Inf:1
☞ Fx:03
Threshld (Threshold)
Sets the level above which the compressor is applied
b
HiEQ (Pre High EQ Gain)
Sets the gain of High EQ
W/D (Wet/Dly)
Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
Wet / Dry
Envelope - Control
–15...+15dB
[Routing]
XCT→CMP, CMP→XCT
Switches the order of the exciter and compressor connection
g
(2)
Gain Adjust High Damp (1)
LoEQ (Pre Low EQ Gain)
Sets the gain of Low EQ
–40...0dB
☞ Fx:03
–Inf, –38...+24dB
☞ Fx:03
Attack
Sets the attack time
1...100
☞ Fx:03
Release
Sets the release time
1...100
☞ Fx:03
75: Exct–Limiter (Exciter – Limiter)
This effect combines a mono-type exciter and a limiter. You
can change the order of the effect connection.
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Left
Wet / Dry
Routing
d
[DLY] T1 (Tap1 Delay)
Sets the Tap1 delay time
0...680ms
T2 (Tap2 Delay)
Sets the Tap2 delay time
0...680ms
EQ Trim LEQ HEQ
0...100
☞ Fx:45
T2 Fb (Tap2 Feedback)
Sets the Tap2 feedback amount
Right
0...100%
☞ Fx:43
[Routing]
LMT→DLY, DLY→LMT
Switches the order of the limiter and multitap delay connection
a
[XCT] Blend (Exciter Blend)
Sets the intensity (depth) of the Exciter effect
b
Emphatic Point
Sets the frequency range to be emphasized
c
Pre EQ Trim
Sets the EQ input level
W/D (Wet/Dly)
Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
h
(Source)
Selects the modulation source of the effect balance
Off...Tempo
(Amount)
Sets the modulation amount of the effect balance
–100...+100
d
e
74: Exct–Comp (Exciter – Compressor)
This effect combines a mono-type exciter and a compressor.
You can change the order of the effect connection.
f
g
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Left
Wet / Dry
Routing
h
Compressor
Exciter
Comp
Exciter
Output Level
Right
Envelope - Control
a
[XCT] Blend (Exciter Blend)
Sets the intensity (depth) of the Exciter effect
b
Emphatic Point
Sets the frequency range to be emphasized
c
Pre EQ Trim
Sets the EQ input level
–100...+100
☞ Fx:11
0...70
☞ Fx:11
0...100
LoEQ (Pre Low EQ Gain)
Sets the gain of Low EQ
–15...+15dB
HiEQ (Pre High EQ Gain)
Sets the gain of High EQ
–15...+15dB
[LMT] Ratio
Sets the signal compression ratio
1.0:1...50.0:1, Inf:1
☞ Fx:03
Threshld (Threshold)
Sets the level above which the compressor is applied
G.Adj (Gain Adjust)
Sets the limiter output gain
–40...0dB
☞ Fx:03
–Inf, –38...+24dB
☞ Fx:03
Attack
Sets the attack time
1...100
☞ Fx:03
Release
Sets the release time
1...100
☞ Fx:03
[Routing]
XCT→LMT, LMT→XCT
Switches the order of the exciter and limiter connection
W/D (Wet/Dly)
Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
EQ Trim LEQ HEQ
+
Wet / Dry
Envelope - Control
Dry, 1:99...99:1, Wet
HiDamp (High Damp)
Sets the damping amount in the high range
g
Limiter
Exciter
–100...+100
Dly W/D (Delay Wet/Dry)
Sets the multitap delay effect balance
f
+
Gain Adjust
T1 Level (Tap1 Level)
Sets the Tap1 output level
e
142
Limiter
Exciter
i
Wet / Dry
–100...+100
☞ Fx:11
0...70
☞ Fx:11
0...100
(Source)
Selects the modulation source of the effect balance
Off...Tempo
(Amount)
Sets the modulation amount of the effect balance
–100...+100