Download FireplaceXtrordinair 95400411 User's Manual
Transcript
564 SS / 564 E Rectangular Face Black 95400411 Compatibility: • 564 SS Fireplace • 564 Electric Fireplace Nickel 95400413 Packing List: • Face • (2) 564 SS Top Brackets (w screws) • 564 E Top and Bottom Brackets • 564 E Top and Bottom Shims • (2) 564 SS Upper Mounting Brackets • (2) 564 SS Lower Mounting Brackets • (2) 10-24 1-1/2" Screws (564 SS only) • 564 E Upper Heat Shield • (14) 8-32 Nuts The center deflectors must be in place when using this face to prevent the facing above the fireplace from becoming too hot. If this face is replacing a Lopi Grill (96200801), make sure to replace the center deflectors. Installation Details – 564 SS 36” SIDE OF FIREPLACE 29” 1” 0” TO 1” NOTE: This face has an adjustable bracket that allows for different facing depths to be tucked under the face. Page 1 of 6 7/19/07 © Travis Industries, Inc. 564 SS / 564 E Rectangular Face Black 95400411 Nickel 95400413 Installation – 564 SS 1 Remove the glass frame (see the owner's manual for details). Install face mounting brackets to the fireplae.. Remove and discard the nuts and bushings above and below the firebox. Discard the stock bushings and nuts. Upper Bracket Place the upper and lower brackets in place and secure using the nuts included with this kit. Discard the stock bushings and nuts. Lower Bracket Repeat these steps for the opposite side. Bracket Alignment - Facing material under 1/2” thick Upper Left Lower Left Page 2 of 6 Bracket Alignment - Facing material 1/2” to 1” thick Upper Upper Left Right Lower Lower Left Right 11/19/07 Upper Right Lower Right © Travis Industries, Inc. 564 SS / 564 E Rectangular Face Black 95400411 Nickel 95400413 Installation – 564 SS (continued) 2 The facing and hearth (if applicable) must be installed prior to attaching the face. See the installation manual for complete details. Raised Fireplaces AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAAAAAA AAAAAAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAAAAAA AAAAAAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA Note how the tile is 1” (maximum) above the base of the fireplace. AAA AAA AAA AAAA AAAAAAA AAAA AAA AAA AAAA AAAA AAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAAAAA AAAA AAAAAAA AAAAAA AAAA AAAAAAA AAAAAA AAAA AAAAAAA AAAAAA AAAA AAAAAAA AAAAAA Floor-Level Fireplaces Maximum 1`” Hearth Page 3 of 6 7/19/07 © Travis Industries, Inc. 564 SS / 564 E Rectangular Face Black 95400411 Nickel 95400413 Installation – 564 SS (continued) 3 Install the face following the directions below. AAAA AAAA AAAA AAAAAAAA AAAA AAAAAAAA AAAAAAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAAA AAA AAAA AAA AAAA AAAA AAAA AAAAAAAAAAA AAA AAAA AAAA AAA AAAA AAAA AAAA AAAAAAAA c a Attach the upper brackets to the face with the included nuts. The face is secured to the fireplace Slide the face into place. The b with four screws. Two of the screws are fastened to the upper brackets tabs on the upper brackets insert into the slots on the fireplace with press nuts. The lower screws brackets, holding the face in place are included with the face. while the screws are tightened. Plated Surfaces Use denatured alcohol and a soft cloth to clean plated surfaces. Marks left on the surface may damage the face. Page 4 of 6 7/19/07 Denatured Alcohol Soft Cloth © Travis Industries, Inc. 564 SS / 564 E Rectangular Face Black 95400411 Nickel 95400413 Installation – 564 Electric 1 Install the upper heat shield onto the 564 E fireplace. Remove the stock upper heat shield. Place the upper heat shield included with this kit on top of the fireplace (note position of heat shield). Place the stock heat shield on top of it and secure with the same screws. AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAA AAAAAAAAAAAA AAAAAA AAAAA AAA AAAAAAAAAAAA AAAAA AAA AAA AAAAAAAAAAAA AAAAA AAA AAAAAAAAAAAA AAAAA AAA AAAAAAAAAAAA AAAAA AAAAAAAAAAAA Page 5 of 6 AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAAAAAAAA AAAAAA AAAAAAAAAAAA AAAAAA AAAA AAAA AAAAAAAAAAAA AAAA AAAA AAAA AAAAAAAAAAAA AAAA AAAA AAAAAAAAAAAA AAAA AAAA AAAAAAAAAAAA AAAA AAAAAAAAAAAA 7/19/07 © Travis Industries, Inc. 564 SS / 564 E Rectangular Face Black 95400411 2 Nickel 95400413 Place the face, face down, on a soft, non-scratching surface. Install the 564 Electric mounting brackets onto the back of the face. c Attach the upper 564 E bracket (and shim). Use the nuts included with this kit. Attach the lower 564 E bracket (and b shim). Use the nuts removed earlier and one of the nuts included with this kit. Remove and a d discard the hinge assembly Repeat steps “a” through “c” for the opposite side. from the face. e Before installing the face verify the lower grill is centered. Loosen the nuts and adjust if necessary. 3 Pull the electric fireplace out of the mantel (or built-in location). Attach the cove covers and face following the directions below. Slide the fireplace back into place to complete the installation. b Lift the face up slightly, tilt it forward and insert the top hooks until the face locks in place. AAAAAAAAAAA AAAAAAAAAAA AAAAAAAAAAA AAAAAAAAAAA AAAAAAAAAAA AAAAAAAAAAA AAAAAAAAAAA AAAAAA AAAAAAAAAAA AAAA AAAAAA AAAAAAAAAAA AAAA AAAA AAAAAAAAAAA AAAA AAA AAAA AAAAAAAAAAA AAAA AAA AAAAAAAAAAA AAAA AAAAAAAAAAA AAAA AAAAAAAAAAA a Tilt the face back slightly and insert the bottom hooks into the slots on the fireplace. Page 6 of 6 7/19/07 © Travis Industries, Inc.