Download Canon PIXMA MP510 Instruction Guide

Start Here
Easy Setup Instructions
Unpack the Machine
Photo All-in-One
• Please confirm the included items against the illustration printed on the lid of the packing box.
• A USB cable is necessary to connect the machine with your computer.
QT5-0453-V02
1 Prepare the Machine
a Place the machine on a flat and horizontal
surface, and do not place any objects in front
of the machine. Open the Front Feeder, and
extend the Paper Output Support and the Paper
Support.
Caution
Before turning on the machine, remove all of the shipping
tapes.
Important
Do not connect the USB cable until after the software is installed.
Important
If an unintended language is displayed on the LCD, proceed
setup to the end of step 3 “Install the Ink Tanks”, and then
refer to “An Unintended Language Is Displayed on the LCD”
in “Troubleshooting” of the User’s Guide on-screen manual to
change the LCD language.
2 Install the Print Head
3 Install the Ink Tanks
a Remove the Print Head from its package.
a Peel back the orange tab completely and remove
the plastic wrapper from the ink tank.
This machine offers two paper sources to load printing
paper; the Auto Sheet Feeder, found at the top of the
machine, and the Front Feeder, found at the front of the
machine.
If the message <Install the print head and set the ink tank.>
appears, go to e.
e Lift the Scanning Unit (Printer Cover) open, and
set the Scanning Unit Support to hold the cover.
The Print Head Holder moves to the center.
Scanning Unit (Printer Cover)
Loading Paper
Caution
There may be some transparent or light blue ink on the inside
of the bag the print head comes in, or the inside of the protective cap - this has no effect on print quality. Be careful not to
get ink on yourself when handling these items.
If the orange-colored protective film is not removed
completely, problems with printing may occur.
b Twist off and discard the orange protective cap
located on the bottom of the ink tank.
b Remove the orange protective cap from the Print
Head and discard it.
Note
• At purchase, the machine is set to feed from the Auto Sheet
Feeder.
• You can load A4, Letter, or B5-sized plain paper in the Front
Feeder. When using any other type of paper, load it in the
Auto Sheet Feeder.
Protective Cap
Ink Port
Do not press!
Auto Sheet Feeder
Electrical Contacts
Electrical Contacts
Important
• Do not touch the electrical contacts.
• Do not touch the ink port.
b Plug the power cord in the back of the machine
and connect the other end to the wall outlet.
f Write down the serial number located inside
the machine. You will need this to register your
product.
Protective Cap
Print Head Nozzles
Note
Do not touch the print head nozzles and the electrical contacts.
c Insert the ink tank into the right-hand slot and
press the
into place.
mark on the ink tank until it clicks
Front Feeder
Loading Paper in the Auto Sheet Feeder
a Load the paper in the Auto Sheet Feeder
with the print side facing UP.
c Firmly raise the Print Head Lock Lever until it
b Align the paper stack against the Cover
stops.
Guide on the right side of the Paper Support.
c Pinch the Paper Guide and slide it against
the left side of the paper stack.
Paper Guide
Print side facing UP.
Serial Number Location
Important
• Plug the power cord all the way in, since it may be difficult to
plug.
• Make sure that the Document Cover is closed.
c Open the Operation Panel, then press the ON/
OFF button to turn on the machine.
d Insert the Print Head.
Cover Guide
d Make sure the ink lamp lights red.
Refer to the color guide on the
Print Head Lock Lever.
Do not touch!
Loading Paper in the Front Feeder
a Load the paper in the Front Feeder with the
e Lower the Print Head Lock Lever carefully.
e Lift the Scanning Unit (Printer Cover) slightly to
set the Scanning Unit Support back to its original
position, and then gently close the Scanning Unit
(Printer Cover).
print side facing DOWN and the leading
edge to the far side.
b Align the paper stack against the right edge
of the Front Feeder.
c Align the near and the left edges of the
paper with the Paper Size Mark.
d Use the { or } button on the Operation Panel to
select the language for the LCD, then press the
OK button.
(1) Press the { or }
button to select the
language.
(2) Press the OK
button.
d Pinch the Paper Guide and slide it against
Important
If the Scanning Unit (Printer Cover) is left open for more than
10 minutes, the Print Head Holder moves to the right. Close
and reopen the Scanning Unit (Printer Cover) to return the
Holder to the center.
the left side of the loaded paper stack.
Paper Guide
Print side facing DOWN.
Important
The machine starts operating. Wait about 2 minutes until the
machine stops making noise.
Hardware setup is complete.
Paper Size Mark
Note
For details, refer to the Quick Start Guide.
Macintosh® MP Drivers Installation
M
ac
W
in
in
do
w
s
to
sh
Windows® MP Drivers Installation
Note
• The screens below refer to Windows XP Service Pack 2 installation.
Screens may vary depending on the operating system you are using.
• For Windows XP or Windows 2000, log on to Windows as a member of the
Administrators group before continuing.
• Before installing the driver, disable all anti-virus programs and automatically
loading programs.
a Turn off the machine.
(1) Press the ON/OFF button.
(2) Make sure that the POWER lamp stops flashing.
b Turn the computer on and start Windows.
f Read the License Agreement carefully and click Yes.
Follow the on-screen instructions to install the software.
If a message asking for your confirmation to restart your
computer appears, click OK.
g When the Printer Connection screen appears, connect the
machine with a USB cable, then turn the machine on. The
software will begin identifying the printer port being used.
Important
If you cannot go to the next procedure after 3 minutes, refer to “Troubleshooting” instructions in the User’s Guide on-screen manual.
Important
Since Mac® OS 9, Mac OS X Classic environments, or Mac OS X v.10.2.7 or
earlier are not supported, do not connect the machine to these.
Note
• Use Mac OS X v.10.2.8 to 10.4.x.
• The screens below refer to Mac OS X v.10.4.x installation. Screens may vary
depending on the operating system you are using.
• Log on as an Administrator before continuing.
• Before installing the driver, disable all anti-virus programs and automatically
loading programs.
a Connect one end of the USB cable to the computer, the
other to the machine.
Important
If you see the Found New Hardware Wizard, remove the USB cable. Click
Cancel to quit the screen. Next, turn off the machine. Then proceed from step
3 to install the MP Drivers.
Note
Make sure the machine is turned on.
g When the list of applications to install appears, confirm the
contents, then click Install.
Note
Move the cursor over items to display explanations of each application below.
h Read the License Agreement carefully and click Yes.
Follow the on-screen instructions to install the software.
i Follow the on-screen instructions to register your product.
Note
When the User Registration screen appears, follow on-screen instructions to
register your product. You will need your product serial number, which is located
on the inside of the machine. See Step 1- f on the front page.
j When the Installation completed successfully screen
appears, click Restart.
The system is restarted automatically.
b Turn on your Mac.
c Insert the Setup CD-ROM. The setup program should run
automatically.
Note
The setup program should run automatically. If the installer in the CD-ROM does
not run automatically, click Start and select My Computer, then double-click the
CD-ROM icon
.
d When the main menu appears, click Easy Install.
c Insert the Setup CD-ROM.
h Follow the on-screen instructions to register your product.
Note
When the User Registration screen appears, follow on-screen instructions to
register your product. You will need your product serial number, which is located on
the inside of the machine. See Step 1- f on the front page.
i When the Installation completed successfully screen
appears, click Exit.
Note
• Select Easy Install in order to install the MP Drivers, on-screen manuals, and
application software. Select Custom Install in order to choose the options you
would like to install.
• To install Adobe® RGB (1998), click Custom Install and follow the on-screen
instructions. If you are using Windows Me/98, Adobe RGB cannot be installed.
e When the list of applications to install appears, confirm the
contents, click Install.
Note
Move the cursor over items to display explanations of each application below.
Note
If the CD-ROM folder does not open automatically, double-click the CD-ROM icon
on the desktop.
d Double-click the Setup icon.
e When the Authenticate screen appears, enter your
administrator name and password. Click OK.
If you do not know your administrator name or password,
click , then follow the on-screen instructions.
*When connecting from Mac OS X v.10.3.3 or earlier:
Restarting the computer while connected to the machine may cause the
machine not to be detected. To resolve this, either unplug the USB cable
then plug it back in again, or turn the machine off then back on again.
k After restarting the computer, start Printer Setup Utility
(start Print Center if you are using Mac OS X v.10.2.8) and
then check that the printer name you want to use is shown
in Printer List. If the printer name is not displayed, click
Add to add the device.
For more detailed instructions, refer to the Mac on-screen
Help.
Now you have completed installation of the
software.
f When the main menu appears, click Easy Install.
If Restart is displayed, make sure that the Restart the system now
(recommended) check box is selected, then click Restart.
Now you have completed installation of the
software.
Note
Select Easy Install in order to install the MP Drivers, on-screen manuals, and
application software. Select Custom Install in order to choose the options you
would like to install.
Part no. QT5-0453-V02 © 2006 Canon Inc. “Windows” is a trademark of Microsoft Corporation, registered in the United States and other countries. “Macintosh” and “Mac” are trademarks of Apple Computer, Inc., registered in the U.S. and other countries. “Adobe” and “Adobe RGB (1998)” are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or other countries. All other product and brand names are trademarks
of their respective owners. Specifications subject to change without notice.
Printed in Vietnam.