Download BENDIX BW2867 User's Manual

Bendix® Trailer Information Module (TIM™) G2
User Guide
User Manual
tion, long hold
hold jumps to
Navigation Buttons and Functionality
Navigation Buttons
Moves menu cursor down. Short hold jumps down one position,
jumps to end of list (Exit).
Moves menu cursor up. Short hold jumps up one position, long hold
top of list.
ed.
User Manu
Navigation Buttons and Functionality
Navigation Buttons
Selects menu item at cursor position.
Using the Navigation Buttons
Cursor Function display
Moves
cursor
down.down
Short
Press menu
to move
the cursor
onehold
level.jumps down one position, long hold
jumps
endtoofjump
list (Exit).
The cursor
is atnoa point
with no sub menu.
Hold to
down
to the final level. (Exit)
Menu
point has
sub menu.
Moves
cursor
up. Short
holdlevel.
jumps up one position, long holdMenu
jumpspoint
to contains a sub menu or an item that may be modified.
Pressmenu
to move
the cursor
up one
The
cursor
is at a point with a sub menu or
topHold
of list.
down to jump up to the top of the list.
an item that may be modified.
Selectmenu
the chosen
item.
Selects
item atmenu
cursor
position.
Cursor Function display
DISPLAYS
With the ignition “ON”
With the ignition “OFF”
The display is off, push any navigation button for one second to
activate the display. Only limited menus are available.
The display is automatically activated. All menus are
available.
Bendix TIM™
TABS-6™
Advanced ABS
DISCLAIMER
For information
only! Press any key
to continue.
or
or
58368LB
or
Initial Menu
or
or
Bendix TIM™
TABS-6™
Advanced ABS
Main Menu
Stored DTCs
Distance & Serv.
Operating Info
System Info
DISCLAIMER
For information
only! Press any key
to continue
or
or
Initial Menu
<Active DTCs >
ODO:
127mi
Load Rear: 58420lb
Inst. Test Missing
or
SAFE MAINTENANCE PRACTICES
WARNING! PLEASE READ AND FOLLOW
THESE INSTRUCTIONS TO AVOID PERSONAL
INJURY OR DEATH:
When working on or around a vehicle, the following general precautions
should be observed at all times:
2.
Park the vehicle on a level surface, apply the parking brakes, and
always block the wheels. Always wear safety glasses. Where
specifically directed, the parking brakes may have to be released,
and/or spring brakes caged, and this will require that the vehicle be
prevented from moving by other means for the duration of these tests/
procedures.
Stop the engine and remove ignition key when working under or
around the vehicle. When working in the engine compartment, the
engine should be shut off and the ignition key should be removed.
Where circumstances require that the engine be in operation,
EXTREME CAUTION should be used to prevent personal injury
resulting from contact with moving, rotating, leaking, heated or
electrically charged components.
3. Do not attempt to install, remove, disassemble or assemble a
component until you have read and thoroughly understand the
recommended procedures. Use only the proper tools and observe
all precautions pertaining to use of those tools.
+
Main Menu
Stored DTCs
Distance & Serv.
Operating Info
ECU Info
or
BATTERY MODE
For information
only! Values are
read from memory!
Scroll until
“Main Menu”
1.
<Active DTCs >
ODO:
127mi
Main Menu
Exit
Scroll until “Main Menu”
TPMS symbol
(where used)
SUPPLY: 11.9V
ODO: 127MI
Initial Menu
Inst. Test Missing
TPMS Info
Main Menu
Exit
4.
or
If the work is being performed on the vehicle’s air brake system,
or any auxiliary pressurized air systems, make certain to drain the
air pressure from all reservoirs before beginning ANY work on the
vehicle. If the vehicle is equipped with a Bendix® AD‑IS® air dryer
system or a dryer reservoir module, be sure to drain the purge
reservoir.
5. Following the vehicle manufacturer’s recommended procedures,
deactivate the electrical system in a manner that safely removes all
electrical power from the vehicle.
6.
Never exceed manufacturer’s recommended pressures.
7.
Never connect or disconnect a hose or line containing pressure; it
may whip. Never remove a component or plug unless you are certain
all system pressure has been depleted.
8. Use only genuine Bendix® brand replacement parts, components
and kits. Replacement hardware, tubing, hose, fittings, etc. must
be of equivalent size, type and strength as original equipment and
be designed specifically for such applications and systems.
9. Components with stripped threads or damaged parts should be
replaced rather than repaired. Do not attempt repairs requiring
machining or welding unless specifically stated and approved by the
vehicle and component manufacturer.
10. Prior to returning the vehicle to service, make certain all components
and systems are restored to their proper operating condition.
11. For vehicles with Automatic Traction Control (ATC), the ATC function
must be disabled (ATC indicator lamp should be ON) prior to
performing any vehicle maintenance where one or more wheels on
a drive axle are lifted off the ground and moving.
MENU OVERVIEW
Initial Menu
Main Menu
Repeat until
“Main Menu”
Trailer Information Module
<Active DTCs >
ODO:
Omi
Load Rear: lb
Inst. Test Missing
Active DTCs:
<none>
Inactive DTCs:
<none>
Clear DTCs
Exit
Date Based
Year:
Month:
Day:
Save & Exit
Exit
Stored DTCs
Distance & Serv.
Operating Info
System Info
+
Stored DTCs
Distance & Serv.
System Config
Operating Info
System Info
ECU Info
TIM Info
Exit
1
<Active DTCs >
ODO:
0mi
Load Rear: lb
Inst. Test Missing 2
TPMS Info 3
Main Menu
Exit
Stored DTCs
Trailer Information Module
Distance & Serv.
System Config.
Operating Info
System Info
ECU Info
TIM Info
ODO:
mi
Trip:
mi
Reset Trip
Srv Date:
Srv mi:
Set Next Service
Exit
ABS Config.:
ECU Orient.:
RSP:
Exit
Info Total
Info Period
Exit
TPMS Setup 3
Load Info
Pressure Info
Tilt Angle:
Wheel Speeds
Air Gap Speeds
Installation Test
Exit
Part num:
SW:
Exit
Lang.:
Set LCD Contrast
Manufacturing Info
Exit
Set Next Service
Info Total
Date Based
Distance Based
Exit
ABS Events
RSP Interventions
Brake History
System Powering
Exit
Info Period
Period mi:
ABS Events:
RSP Interventions
Brake History
System Powering
Reset Period Data
Exit
TPMS Setup 3
Distance Based
Srv mi:
Save & Exit
Exit
Load Info
Enter conf. Mode
Learn Sensor 5
Delete Sensor 5
Vehicle param.5
Axle param.5
Altitude comp:5
Change password 5
Leave conf. Mode 5
Exit
6
Front Axle Group
Bogie Load: 4
Rear Axle Group
Exit
4
Set LCD Contrast
Manufacturing Info
Language
LCD Contrast:
Save & Exit
Exit
Part num:
K001966XXXXXX
SW:
Serial:
ManufDate:
Exit
English (US)
N.Am. French
N.Am. Spanish
Exit
Pressure Info
Installation Test
Wheel Speeds
Airgap Speeds
Dem P4:
Dem CAN:
Susp P42:
Pcyl P21:
Pcyl P22:
Res P1:
Exit
Start Inst. Test
Install Check
Reserv. Press
S-A Sensor: 4
S-E Sensor: 4
S-C Sensor:
S-D Sensor:
S-F Sensor: 4
S-B Sensor: 4
Demand Press:
Tilt Angle:
Exit
S-A Sensor:
S-E Sensor: 4
S-C Sensor:
S-D Sensor:
S-F Sensor: 4
S-B Sensor: 4
Exit
S-A Sensor: 4
S-E Sensor: 4
S-C Sensor:
S-D Sensor:
S-F Sensor: 4
S-B Sensor: 4
Exit
RSP Intervention
Brake History
System Powering
Enter conf. Mode 6
Vehicle param. 5
Change password 5
Test Puls:
Step 1:
Step 2:
Step 3:
Exit
Appl vs Dem Values
Over Pressures
Exit
ConstPower:
Stop Lamp:
Exit
Password:
Match password
Exit
FAL% CIP:
SAL % CIP:
Over Temp:
Exit
Password:
New passw.:
Save new passw.
Exit
Appl vs Dem Values
Over Pressures
<22psi:
22-36psi:
36-58psi:
>58psi:
Exit
Dem >130psi:
Res >130psi:
Exit
Displayed only if active faults are available
Displayed only if installation test is missing
3 Displayed only if Tire Pressure Monitoring System (TPMS) is configured
4 Displayed only if included by vehicle ABS configuration
5 Displayed only if TPMS configuration mode entered
6 Displayed only if TPMS configuration mode not entered
1
2
Menu choices in green are not available in BATTERY MODE
4
EXAMPLES
a) Setting next service distance to
6,250 miles (mi)
b) Display current Diagnostic
Trouble Code (DTC) status
Main Menu
Stored DTCs
Distance & Serv.
Operating Info
System Info
Main Menu
Stored DTCs:
Distance & Serv.
Operating Info
System Info
1x
*
Srv Mi:
Save & Exit
Exit
+
Reset Trip
Srv Date
Srv Mi:
Set Next Service
18-01-10
6240mi
*
Main Menu
System Info
ECU Info
TIM Info
Exit
Scroll to “TIM Info”
0mi
+
Overview of DTC
= 6250 mi
+
5x
Lang.: US English
Scr Saver: Load
Set LCD Contrast
Manufacturing Info
Active DTCs:
S-C O/C.
S-D O/C.
Module Error
“ ” Indicates cursor buttons
and
are now used to change ‘mi’ values
2x
c) Changing the language
default
1x
+
+
Srv Mi:
Save & Exit
Exit
Date Based
Distance Based
Exit
6250mi
*
NOTE: “ ” inactive, buttons
revert to normal function
1x
+
DTC Detail
S-C Open circuit or
Shorted to Battery
DTC:
and
US English
N.Am. French
N.Am. Spanish
Exit
000D00
1x
Scroll
+
1x
+
Srv Mi:
Save & Exit
Exit
0mi
Occurrence count:
Next service
distance has been
succesfully set in
ECU.
Langue: N.Am. French
Eco ecran Charger
Régl Contraste LCD
Info Fabricant
4
First detection:
0mi
Scroll to “Sortie” (Exit)
Scroll
END
2008-03-15 19:43.44
Last detection:
2008-03-31 10:11.47
Info Fabricant
Test Affichage
Test Touche
Sortie
0mi
END
END
d) Installation test
Initial Menu
<Active DTCs>
ODO:
127mi
Load Rear: 58420lb
Inst. Test Missing
Scroll to “Inst. Test Missing”
+
Confirm that
cables are securely
clipped, then
press ENTER.
all its brakes may
be released automatically! Press
ENTER to confirm
2x
= Confirm
Scroll and follow
instructions on the
screen
Confirm that wheel
speed sensors have
been set, then
press ENTER.
matically! Press
ENTER to confirm
you have secured
the Trailer.
= Confirm
= Confirm
Confirm that all
non connected
ports are plugged
then press ENTER.
SECURE Trailer
against movement!
During this test
all its brakes may
3x
Fully apply the brake
pedal, then release it
Overview of wheel
location, “Confirm”
Installation test
is missing! To
start it browse to:
Main Menu->
Start Inst. Test
Install. Check:
Reserv. Press:
S-C Sensor:
Reserv. Press:
S-C Sensor:
S-D Sensor:
Demand Press:
S-C Sensor:
S-D Sensor:
Demand Press:
Tilt Angle:
Start Inst. Test
Install. Check:
Reserv. Press:
S-C Sensor:
2x
< 5o
Accelerate selected
wheel to 3mph
Installation test
has been successfully executed.
Please switch igni-
Confirm that the
Truck‘s parking
brake is applied
then press ENTER.
= Confirm
Confirm that pneumatic connections
are secure, then
press ENTER.
2x
= Confirm
Confirm that the
Trailer‘s parking
brake is NOT active
then press ENTER.
= Confirm
TEBS mounting angle
within tolorance
= Confirm
(if reservoir pressure > 6Bar)
Overview of wheel
location, “Confirm”
fully executed.
Please switch ignition OFF-ON to
memorize status.
Install. Check:
Reserv. Press:
S-C Sensor:
S-D Sensor:
2x
Accelerate selected
wheel to 3mph
Start Inst. Test
Install. Check:
Reserv. Press:
S-C Sensor:
END
BW2867 © 2011 Bendix Commercial Vehicle Systems LLC, a member of the Knorr-Bremse Group. 10/11. All Rights Reserved.