Download Avaya Reporting for Call Center User's Manual
Transcript
Reporting for Call Center Set Up and Operations Guide www.nortelnetworks.com © 2004 Nortel Networks P1012912 Issue 02 (05) Table of Contents Change History ........................................................................................................... 1 How to Use This Guide............................................................................................... 2 Introduction ..........................................................................................................................................2 How This Guide is Organized ..............................................................................................................2 Introduction ................................................................................................................. 4 Introduction ..........................................................................................................................................4 Web Based User Interface...................................................................................................................4 Language Support ...............................................................................................................................4 Administrators and Users.....................................................................................................................5 Assigned Skillsets ................................................................................................................................5 SQL Historical Database......................................................................................................................6 System Software ..................................................................................................................................6 PC Requirements.................................................................................................................................6 Minimum PC Specifications ............................................................................................................6 Operating System Compatibility...........................................................................................................7 Installation................................................................................................................... 8 Introduction ..........................................................................................................................................8 Upgrading to Reporting for Call Center ...............................................................................................8 Upgrading a Previous Version of Reporting for Call Center ................................................................8 Deleting Temporary Internet Files ..................................................................................................9 Installation prerequisites ....................................................................................................................10 Installing Nortel Networks Reporting for Call Center software ..........................................................11 TCP/IP Protocol ............................................................................................................................11 Checking whether the Windows Networking Component Is Installed ..........................................11 Installing Nortel Networks Reporting for Call Center ....................................................................12 For a Business Communications Manager Installation ..........................................................12 For a CallPilot Installation.......................................................................................................13 Call Center Reporting Server........................................................................................................21 Administration........................................................................................................... 23 Logging In ..........................................................................................................................................23 Changing Default Password ..............................................................................................................24 Administration Menu ..........................................................................................................................25 Call Center Connection.................................................................................................................26 System Administration ..................................................................................................................30 System Admin Settings ..........................................................................................................31 User Admin .............................................................................................................................32 Administration and User Permissions ....................................................................................35 Skillset Assignment ................................................................................................................38 Reporting.......................................................................................................................................41 Maintenance .................................................................................................................................41 System Status.........................................................................................................................42 ii Table of Contents Logging...................................................................................................................................42 Company Details ..........................................................................................................................44 Reporting ......................................................................................................................................45 Using Reporting for Call Center .............................................................................. 47 Logging In ..........................................................................................................................................47 Time Bins Setup ................................................................................................................................50 Answer Time Bins.........................................................................................................................50 Abandon Time Bins ......................................................................................................................50 Print Schedules..................................................................................................................................54 Daily Schedules ............................................................................................................................55 Skillset List Selection Methods .....................................................................................................60 Adding Selections to the Favourites List ......................................................................................61 Weekly Schedules ........................................................................................................................65 Monthly Schedules .......................................................................................................................74 Real Time...........................................................................................................................................83 Using the Real Time Options........................................................................................................83 Real Time Summary...............................................................................................................83 Real Time Summary - Agent Summary .................................................................................85 Real Time Summary – Call Summary....................................................................................86 Hiding the Real Time Panels..................................................................................................88 Real Time Detail .....................................................................................................................88 Call Detail ...............................................................................................................................89 Agent Detail ............................................................................................................................91 Agent Alarms .....................................................................................................................................94 Wallboard Setup ................................................................................................................................97 Introduction ...................................................................................................................................97 Message Formats .........................................................................................................................98 Parameter Messages .............................................................................................................98 Scrolling Messages ................................................................................................................98 Summary Messages.............................................................................................................100 Using the Wallboard Options ......................................................................................................100 Wallboard Assignment Page ................................................................................................101 Add Wallboard Page ............................................................................................................103 Wallboard Parameters..........................................................................................................105 Wallboard Messages Page ..................................................................................................108 Alarms ..................................................................................................................................111 Schedules.............................................................................................................................117 Instant Messages .................................................................................................................122 Reports .................................................................................................................... 125 Reports Introduction ........................................................................................................................125 General .......................................................................................................................................125 Report Periods .....................................................................................................................125 Skillset Selection ..................................................................................................................125 Voice and Multimedia Calls ..................................................................................................125 Direct and Indirect Calls .......................................................................................................125 Calls and Call Transactions..................................................................................................126 Call Transactions and the Direct and Indirect Calls .............................................................126 In-Progress Calls ..................................................................................................................127 Report Headers ....................................................................................................................127 Report Viewer Toolbar................................................................................................................127 Printing a Report ..................................................................................................................128 Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Table of Contents iii Exporting A Report ...............................................................................................................128 Report Magnification.............................................................................................................130 Report Navigation .................................................................................................................130 Searching for Text Within A Report ......................................................................................130 Using the Reports ............................................................................................................................131 Get latest Call Center Data Button .............................................................................................132 Answered Calls Report ...............................................................................................................132 Abandoned Call Report...............................................................................................................134 Abandoned Calling Line ID Report .............................................................................................137 Agent Capacity Report................................................................................................................139 Help Request Report ..................................................................................................................141 Call Average Report....................................................................................................................144 Agent Average Report ................................................................................................................146 Agent Profile Report....................................................................................................................149 Agent Activity Report ..................................................................................................................153 Agent Audit Report......................................................................................................................156 Activity Code Report by Skillset ..................................................................................................161 Activity Code Report by Agent ....................................................................................................165 Activity Code Report by # of Pegs ..............................................................................................169 Summary Report.........................................................................................................................173 Summary Report Table ........................................................................................................175 Summary Report Graphs......................................................................................................176 Call Profile Report.......................................................................................................................178 Call Profile Report Table ......................................................................................................179 Call Profile Report Graph .....................................................................................................181 Incoming Call Report ..................................................................................................................182 Incoming Call Report Table ..................................................................................................184 Incoming Call Report Graph .................................................................................................186 Unanswered Help Request Report .............................................................................................188 Agent Average Report by Agent .................................................................................................191 Agent Activity Report by Skillset .................................................................................................193 Issue 02 (05) Reporting for Call Center Set Up and Operations Guide iv Table of Contents Reports Explained .................................................................................................. 197 Answered Calls Report ....................................................................................................................197 Abandoned Call Report ...................................................................................................................199 Abandoned Calling Line ID Report ..................................................................................................201 Help Request Report .......................................................................................................................205 Call Average Report ........................................................................................................................207 Agent Average Report .....................................................................................................................208 Agent Profile Report ........................................................................................................................210 Agent Activity Report .......................................................................................................................212 Agent Audit Report ..........................................................................................................................213 Activity Code Report by Skillset.......................................................................................................214 Activity Code Report by Agent.........................................................................................................216 Activity Code Report by # of Pegs ...................................................................................................218 Summary Report..............................................................................................................................220 Call Profile Report............................................................................................................................222 Incoming Call Report .......................................................................................................................224 Unanswered Help Request Report ..................................................................................................225 Agent Average Report by Agent ......................................................................................................226 Agent Activity Report by Skillset ......................................................................................................227 Upgrading to Reporting for Call Center ................................................................ 228 Introduction .................................................................................................................................228 What Do I have to Install?...........................................................................................................228 Can the old Master PC be used as the Web Host PC?..............................................................228 Why is there No ‘Multiple Client’ software to install?..................................................................228 Do I have to remove the old Nortel Networks Call Center Reporting 2.5, 3.0 or 3.5 software?.228 Can the new software co-reside with the old software? .............................................................228 Troubleshooting Reporting for Call Center .......................................................... 230 Slow Updates on Real Time Screen................................................................................................230 Web Host PC Requires a Host File entry ...................................................................................230 Anti-Virus Software Slowing Down the File System ........................................................................230 Cannot Access the Login Page .......................................................................................................231 Turning off script blocking in Norton Anti-Virus 2001 .................................................................231 Turning off script blocking in Norton Anti-Virus 2002 or 2003 ....................................................232 Changing Agent Names...................................................................................................................233 Virtual Folders Not Created in Internet Information Services ..........................................................234 Accessing Networked Printers From the Web Host PC ..................................................................235 Multiple Network Cards in the Web Host PC or an Agent PC .........................................................235 ipView SoftBoard and Wallboard Summaries..................................................................................236 Crystal Reports ActiveX Report Viewer...........................................................................................236 Real Time Screens on Client PCs ...................................................................................................237 Glossary .................................................................................................................. 238 References............................................................................................................... 242 Index ........................................................................................................................ 243 Reporting for Call Center Set Up and Operations Guide Issue 02 (05) ii Table of Figures Table of Figures Figure 1 Internet Properties Window .......................................................................................................................................9 Figure 2 Delete Files Dialog ..................................................................................................................................................10 Figure 3: InstallShield Initialization Dialog ...........................................................................................................................13 Figure 4: Language Selection Dialog .....................................................................................................................................13 Figure 5: InstallShield Windows Installer Configuration Dialog ...........................................................................................14 Figure 6: InstallShield Wizard Start Dialog ...........................................................................................................................15 Figure 7: License Agreement Dialog .....................................................................................................................................16 Figure 8: Customer Information Dialog .................................................................................................................................17 Figure 9: Choose Destination Location ..................................................................................................................................18 Figure 10: Setup Status Dialog...............................................................................................................................................19 Figure 11: Database Installation Dialog .................................................................................................................................19 Figure 12: Java Installation Dialog.........................................................................................................................................20 Figure 13: Installation Complete Dialog ................................................................................................................................20 Figure 14 Log In page ............................................................................................................................................................24 Figure 15 Change Password Page ..........................................................................................................................................25 Figure 16 Administration Menu Page ....................................................................................................................................26 Figure 17 Call Center Connection Page .................................................................................................................................27 Figure 18 Connection Security Setting Changed Reboot Message ........................................................................................28 Figure 19 Starting Data Download notification Message.......................................................................................................29 Figure 20 Download Status Window .....................................................................................................................................29 Figure 21 System Administration Menu Page........................................................................................................................31 Figure 22 System Administrator details page.........................................................................................................................32 Figure 23 User Admin Page ...................................................................................................................................................33 Figure 24 Add User Page .......................................................................................................................................................34 Figure 25 Details for new User Mary Smith ..........................................................................................................................36 Figure 26 Edit User Page........................................................................................................................................................37 Figure 27 Skillset Assignment Page.......................................................................................................................................38 Figure 28 Assigned Skillsets Page .........................................................................................................................................39 Figure 29 Skillsets Assigned to User Mary Smith..................................................................................................................40 Figure 30 Maintenance Menu Page........................................................................................................................................41 Figure 31 System Status Page ................................................................................................................................................42 Figure 32 Logging Menu Page ...............................................................................................................................................43 Figure 33 Logging Menu Page, with the Logging Stopped....................................................................................................44 Figure 34 Company Details Page ...........................................................................................................................................45 Figure 35 Main Menu Page ....................................................................................................................................................46 Figure 36 Log In Page ............................................................................................................................................................47 Figure 37 Change Password Page ..........................................................................................................................................48 Figure 38 User Main Menu Page............................................................................................................................................49 Figure 39 Time Bins Setup (Configuration) Menu Page........................................................................................................51 Figure 40 Time Bin Setup Skillset Selection page .................................................................................................................52 Figure 41 Time Bins Page ......................................................................................................................................................53 Figure 42 Print Schedules Page..............................................................................................................................................55 Figure 43 Your Daily Schedules Page....................................................................................................................................56 Figure 44 Add Daily Schedule Page ......................................................................................................................................57 Figure 45 Add Daily Schedule Page - Example Settings .......................................................................................................59 Figure 46 Daily Schedule Skillsets Page................................................................................................................................60 Figure 47 Save Favourites Page .............................................................................................................................................62 Figure 48 Your Daily Schedules with a Schedule in the List ................................................................................................63 Figure 49 Edit Daily Schedules Page .....................................................................................................................................64 Figure 50 Your Weekly Schedules Page ................................................................................................................................66 Figure 51 Add Weekly Schedule Page ...................................................................................................................................67 Figure 52 Calendar for September 2003.................................................................................................................................68 Figure 53 Add Weekly Schedule Page - Example Schedule ..................................................................................................69 Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Table of Figures iii Figure 54 Weekly Schedules - Skillsets ................................................................................................................................ 70 Figure 55 Your Weekly Schedule Page with a Schedule in the List...................................................................................... 72 Figure 56 Edit Weekly Schedule Page .................................................................................................................................. 73 Figure 57 Your Monthly Schedules Page .............................................................................................................................. 74 Figure 58 Add Monthly Schedule Page................................................................................................................................. 75 Figure 59 Add Monthly Schedule Page with Example Schedule .......................................................................................... 77 Figure 60 Monthly Schedule - Skillsets Page ........................................................................................................................ 78 Figure 61 Your Monthly Schedules Page with a Schedule in the List................................................................................... 80 Figure 62 Edit Monthly Schedule Page ................................................................................................................................. 81 Figure 63 Real Time Menu Page ........................................................................................................................................... 83 Figure 64 Real Time Summary Skillset Selection Page ........................................................................................................ 84 Figure 65 Real Time Summary Real Time Screens............................................................................................................... 85 Figure 66 Real Time Detail Skillset Selection Page .............................................................................................................. 89 Figure 67 Real Time Call Detail Page ................................................................................................................................... 90 Figure 68 Agent Detail Real Time Page ................................................................................................................................ 92 Figure 69 Agent Alarm Menu Page....................................................................................................................................... 95 Figure 70 Agent Alarms Setup Page...................................................................................................................................... 96 Figure 71 Agent Alarms Values Page.................................................................................................................................... 97 Figure 72 Wallboard Menu Page ......................................................................................................................................... 101 Figure 73 Wallboard Assignment Page ............................................................................................................................... 102 Figure 74 Add Wallboard Page ........................................................................................................................................... 103 Figure 75 Wallboard Setup Page with Wallboard Listed .................................................................................................... 105 Figure 76 Edit wallboard Page ............................................................................................................................................ 106 Figure 77 Edit Parameters Page........................................................................................................................................... 107 Figure 78 Assigned Messages Page..................................................................................................................................... 108 Figure 79 Add Message Page .............................................................................................................................................. 109 Figure 80 Add Message Page - Example Text..................................................................................................................... 110 Figure 81 Assigned Messages List - Example Messages .................................................................................................... 111 Figure 82 Assigned Alarms Page ........................................................................................................................................ 112 Figure 83 Add Alarm Page .................................................................................................................................................. 113 Figure 84 Example Settings for a Multi Alarm Period Alarm ............................................................................................. 116 Figure 85 Assigned Schedules Page .................................................................................................................................... 118 Figure 86 Add Schedule Page.............................................................................................................................................. 119 Figure 87 Assigned Schedules Page with Schedule Added ................................................................................................. 120 Figure 88 Edit Schedule Page.............................................................................................................................................. 121 Figure 89 Instant Messages Page......................................................................................................................................... 122 Figure 90 Composing an Instant Message ........................................................................................................................... 123 Figure 91 Example Report Header ...................................................................................................................................... 127 Figure 92 Report Viewer Toolbar........................................................................................................................................ 128 Figure 93 Report Printer Selection Window........................................................................................................................ 128 Figure 94 Export Report Window ....................................................................................................................................... 129 Figure 95 Report Menu Page............................................................................................................................................... 131 Figure 96 Answered Calls Report Skillsets Page ................................................................................................................ 133 Figure 97 Answered Calls Report........................................................................................................................................ 134 Figure 98 Abandoned Call Report Skillset Page ................................................................................................................. 135 Figure 99 Abandoned Call Report....................................................................................................................................... 136 Figure 100 Abandoned Calling Line ID Skillset page......................................................................................................... 137 Figure 101 Abandoned Calling Line ID Report .................................................................................................................. 138 Figure 102 Agent Capacity Report Skillsets page ............................................................................................................... 139 Figure 103 Agent Capacity Report ...................................................................................................................................... 141 Figure 104 Help Request Report page................................................................................................................................. 142 Figure 105 Help Request Report ......................................................................................................................................... 143 Figure 106 Call Average Report Skillset page .................................................................................................................... 144 Figure 107 Call Average Report.......................................................................................................................................... 145 Figure 108 Agent Average Report Skillset Selection Page ................................................................................................. 147 Figure 109 Agent Average Report....................................................................................................................................... 149 Issue 02 (05) Reporting for Call Center Set Up and Operations Guide iv Table of Figures Figure 110 Agent Profile Report Skillset page.....................................................................................................................150 Figure 111 Agent Profile Report ..........................................................................................................................................152 Figure 112 Agent Activity Report Skillsets page .................................................................................................................154 Figure 113 Agent Activity Report........................................................................................................................................155 Figure 114 Agent Audit Report Skillset Selection page.......................................................................................................157 Figure 115 Agent Selection Page .........................................................................................................................................158 Figure 116 Agent Selection page with No Agents Available ...............................................................................................159 Figure 117 Agent Audit Report............................................................................................................................................160 Figure 118 Activity Code Report By Skillset Skillset page .................................................................................................161 Figure 119 Select Activity Code page..................................................................................................................................162 Figure 120 Select Activity Codes page – No Activity Codes...............................................................................................163 Figure 121 Activity Code Report by Skillset .......................................................................................................................164 Figure 122 Activity Code Report By Agent Skillset page....................................................................................................165 Figure 123 Select Activity Code page..................................................................................................................................166 Figure 124 Select Activity Codes page – No Activity Codes...............................................................................................167 Figure 125 Agent Activity Code Report by Agent...............................................................................................................168 Figure 126 Activity Code Report By # of Pegs Skillset page ..............................................................................................169 Figure 127 Select Activity Code page..................................................................................................................................170 Figure 128 Select Activity Codes page – No Activity Codes...............................................................................................171 Figure 129 Agent Activity Code Report by Number of Pegs...............................................................................................172 Figure 130 Summary Report Skillset page...........................................................................................................................173 Figure 131 Summary Report ................................................................................................................................................174 Figure 132 Summary Report Graphs....................................................................................................................................177 Figure 133 Call Profile report Skillset Selection page .........................................................................................................178 Figure 134 Call Profile Report .............................................................................................................................................180 Figure 135 Call Profile Report Graph ..................................................................................................................................182 Figure 136 Incoming Call Report Skillset Selection page....................................................................................................183 Figure 137 Incoming Call Report.........................................................................................................................................184 Figure 138 Incoming Call Report Graph..............................................................................................................................187 Figure 139 Unanswered Help Request Report Selection page .............................................................................................189 Figure 140 Unanswered Help Request Report .....................................................................................................................190 Figure 141 Agent Average Report by Agent Skillset Selection Page ..................................................................................191 Figure 142 Agent Average Report by Agent........................................................................................................................192 Figure 143 Agent Activity Report by Agent Skillset Selection Page...................................................................................194 Figure 144 Agent Activity Report by Agent ........................................................................................................................195 Figure 145 Answered Calls Report ......................................................................................................................................197 Figure 146 Abandoned Call Report......................................................................................................................................199 Figure 147 Abandoned Calling Line ID Report ...................................................................................................................201 Figure 148 Agent Capacity Report.......................................................................................................................................203 Figure 149 Help Request Report ..........................................................................................................................................205 Figure 150 Call Average Report...........................................................................................................................................207 Figure 151 Agent Average Report .......................................................................................................................................208 Figure 152 Agent Profile Report ..........................................................................................................................................210 Figure 153 Agent Activity Report........................................................................................................................................212 Figure 154 Agent Audit Report............................................................................................................................................213 Figure 155 Activity Code Report .........................................................................................................................................214 Figure 156 Agent Activity Code Report by Agent...............................................................................................................216 Figure 157 Agent Activity Code Report by Number of Pegs...............................................................................................218 Figure 158 Summary Report ................................................................................................................................................220 Figure 159 Summary Report Graphs Page ...........................................................................................................................221 Figure 160 Call Profile Report .............................................................................................................................................222 Figure 161 Call Profile Report Graph Page..........................................................................................................................223 Figure 162 Incoming Call Report.........................................................................................................................................224 Figure 163 Help Request Unanswered Report .....................................................................................................................225 Figure 164 Agent Average Report by Agent.......................................................................................................................226 Figure 165 Agent Activity Report by Skillset ......................................................................................................................227 Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Table of Figures v Figure 166 Example Host File ............................................................................................................................................. 230 Figure 167 Norton Anti-Virus Options Screen.................................................................................................................... 232 Figure 168 Norton Anti-Virus Options Dialog.................................................................................................................... 233 Figure 169 Page Cannot Be Displayed Error Message........................................................................................................ 234 Figure 170 ipView Help Window........................................................................................................................................ 236 Issue 02 (05) Reporting for Call Center Set Up and Operations Guide Change History 1 Change History Issue 01 (11) – March 2004 1. First Public Release. Issue 01 (12) – April 2004 1. 2. 3. 4. Note on Windows 2003 compatibility added. Call Center Connection Page section expanded. Troubleshooting Section expanded. GOS % Formula changed in Glossary. Issue 02 (2) – August 2004 1. 2. 3. 4. CallPilot 3.0 references added. Deleting temporary internet files added. New report descriptions added. CCRS Installation section added. Issue 02 (3) – August 2004 1. Figure numbers modified in body text. Issue 02 (4) – August 2004 1. Latest CCR installation routine added. Issue 02 (5) – September 2004 1. 2. User and Administrators permissions discussion added. Note adding regarding reboot of the Web Host following the addition of a new Network Interface Card. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 2 How to Use This Guide 1 How to Use This Guide Introduction This document is designed to allow an Administrator or User to set up and operate Nortel Networks Reporting for Call Center. Use this document as an ongoing reference. This chapter tells you what to expect as you read this document and how information in this document is presented. How This Guide is Organized The Reporting for Call Center Set Up and Operations Guide is organized according to the following chapters: How to use this Document Provides a brief overview identifying the organization of this test plan. Introduction Provides an overview of the conceptual organization of the Nortel Networks Reporting for Call Center product. Installation Describes the minimum specification for the PC required to host Nortel Networks Reporting for Call Center. Describes how to install Nortel Networks Reporting for Call Center. Administration Describes the Administration duties and configuration that must be conducted to ensure that Nortel Networks Reporting for Call Center operates correctly. Using Reporting for Call Center Describes the usage and configuration of Nortel Networks Reporting for Call Center from a User’s perspective. Reports Describes the reports that are available within Nortel Networks Reporting for Call Center. Upgrading to Reporting for Call Center Describes how you can upgrade from a previous installation of Call Center Reporting 2.5, 3.0 or 3.5 to Nortel Networks Reporting for Call Center. Glossary Describes the terms used within this User Guide. References Lists any other documents referenced from within the body of this document. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) How to Use this Guide3 Index Issue 02 (05) A cross-reference of topics in this User Guide. Reporting for Call Center Set Up and Operations Guide 4 Introduction Introduction 2 Introduction Nortel Networks Reporting for Call Center is a browser-based Real Time information and Historical Reporting tool for Nortel Networks Call Center. Nortel Networks Reporting for Call Center provides: • • • Real Time windows showing current Call Center activity, for Calls and for Agents Real Time information via hardware and software IP-enabled wallboards A comprehensive Historical Reporting package ! Within this document the phrase ‘the Call Center platform’ is used to refer to either the Business Communications Manager or the CallPilot hardware, and the phrase ‘the Call Center’ is used to refer to the Call Center application running on that platform. The platforms are only referenced specifically by name in areas of this document describing the installation of the Call Center Reporting application software, on Pages 13, 14, 17, 18 & 19, and the discussion concerning the configuration of the Call Center Connection page, on Page 27. Web Based User Interface All of the Administrative and User interactions with Nortel Networks Reporting for Call Center are conducted through a series of Web Pages accessed via Internet Explorer browser sessions. These Web Pages are hosted on a nominated PC which is referred to as the Web Host PC, onto which the Nortel Networks Reporting for Call Center software is installed. The Web Host PC communicates directly with the Call Center to retrieve Real Time updates (for the Real Time screens and wallboards) and Historical information (for the reports). Other PCs that have network access to the Web Host PC can access these Web Pages. This allows multiple Users to use Nortel Networks Reporting for Call Center, without having any software other than Internet Explorer installed on their PCs . Language Support Each Administrator or User of Nortel Networks Reporting for Call Center can have their Web user Interface pages presented to them in one of the following 13 languages: North American Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Introduction 5 English, United Kingdom English, Canadian French, Latin American Spanish, Brazilian Portuguese, Spanish, Dutch, French, German, Italian, Norwegian, Danish, Swedish. Individual wallboards can also be driven in any of these languages. Administrators and Users There are two types of user of Nortel Networks Reporting for Call Center. These are called Administrators and Users. As well as having access to all of the usual features of Nortel Networks Reporting for Call Center, Administrators can specify and change fundamental configuration settings within Nortel Networks Reporting for Call Center. For security purposes and to maintain system stability, ordinary Users cannot change these fundamental configuration settings, only Users with Administrator’s capabilities . User interactions with Nortel Networks Reporting for Call Center are limited to using the features that it provides. Whilst Users cannot modify the core set-up of Nortel Networks Reporting for Call Center, they can however specify and change some personal preferences and they can configure aspects of Nortel Networks Reporting for Call Center which only affect themselves. Administrators and Users are presented with different menus when they login. Assigned Skillsets Administrators create the Users by providing details such as User Name and language to Nortel Networks Reporting for Call Center. The Administrator must then assign Skillsets to the Users. This process defines which Skillsets each User can view in the Real Time screens and request Historical Reports on. Skillsets may be assigned to more than one User. Users can choose to view the Real Time screens or Historical Reports for any of the Skillsets which have been assigned to them, or any combination of the allocated Skillsets, or all of the assigned Skillsets. Selections of Skillsets which are frequently used can be saved as Favourites. The Favourites are given names to identify them. This makes it easy and quick to select a certain selection or category of Skillsets through a single click of the mouse. Favourites are unique to each User. This allows the User to create, modify or delete Favourites to suit themselves. This will not affect the Favourites of any other User. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 6 Introduction SQL Historical Database Historical Report information is stored in a standard MySQL database allowing the User to analyze the data using third-party reporting packages, should they have reporting requirements which are not catered for by the reports contained within Nortel Networks Reporting for Call Center. System Software The software that sends data to Nortel Networks Reporting for Call Center is integral to Nortel Networks Call Center Nortel Networks Reporting for Call Center software on the Web Host PC communicates directly to the Call Center to request Call Center Historical Report statistical data and Real Time data. Other Users (on different PCs) simply point their Internet Explorer browsers to the Nortel Networks Reporting for Call Center Web Pages on the Web Host PC to access the Real Time and Historical Report data. No other PC apart from the Web Host PC needs to communication with the Call Center. ! One PC on your network should be nominated as the Web Host PC. Only install the Nortel Networks Reporting for Call Center application software onto this single PC. All other PCs on your network from which Users wish to access the Real Time screens, Historical Reports or the Nortel Networks Reporting for Call Center user interface must be equipped with Internet Explorer. No other software is required on these PCs. PC Requirements The minimum requirements of the PC required to operate as the Nortel Networks Reporting for Call Center Web Host PC are listed below. Minimum PC Specifications IBM™ Compatible PC Microprocessor Intel® PentiumTM III (or equivalent) minimum, Intel® PentiumTM IV (or equivalent) recommended. Microprocessor Speed 400 MHz minimum, 1.0 GHz recommended Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Introduction 7 Memory 64 MB minimum, 128 MB recommended Network Interface Card TCP/IP protocol SVGA display Mouse (or other Windows® compatible Pointing Device) Microsoft Internet Explorer version 5 or higher Operating System Microsoft Windows NT 4 Service Pack 6a Microsoft Windows 2000 Service SP2 Microsoft Windows XP Professional These are the ONLY supported operating systems. Note: Windows 2003 Server is undergoing compatibility testing, but Windows 2003 Server is currently NOT a supported Operating System. Web Server Nortel Networks Reporting for Call Center has been verified with Microsoft Internet Information Services 4 and 5 Hard Disk Space Required For installation of application on Web Server: 80 MB Storage space required for Historical Data: (approx) 256 bytes per call. Note that the database will grow through time, and that if the diagnostic logging option is turned on the log files will require extra disk space as well. Operating System Compatibility Nortel Networks Reporting for Call Center has been verified for correct operation on the following Operating Systems: Operating System Windows NT Windows 2000 Windows XP Professional Issue 02 (05) Version 4.00.1381 5.00.2195 Version 2002 Reporting for Call Center Set Up and Operations Guide 8 Installation Installation 3 Introduction This chapter describes the installation prerequisites and how to install the Nortel Networks Reporting for Call Center software on the Windows Personal Computer you wish to use as the Web Host PC. The Web Host PC is the one which will communicate with Nortel Networks Call Center. The Web Host PC also stores the Call Center statistical database and the Nortel Networks Reporting for Call Center user interface, which is configured as a web site. Other network users can use Internet Explorer to browse to the Nortel Networks Reporting for Call Center web site on the Web Host PC to access the software features and obtain Real Time displays and Reports. Upgrading to Reporting for Call Center This chapter describes the first-time installation of Nortel Networks Reporting for Call Center on a Web Host PC that has never had Nortel Networks Reporting for Call Center installed on it. If you are upgrading from Call Center Reporting 2.5, 3.0 or 3.5, please refer to the chapter titled Upgrading to Reporting for Call Center on Page 228. If you are upgrading from a previous version of Nortel Networks Reporting for Call Center to a newer version of Nortel Networks Reporting for Call Center please refer to the section titled Upgrading a Previous Version of Reporting for Call Center, below. Upgrading a Previous Version of Reporting for Call Center In order to perform an upgrade of a previous installation of Nortel Networks Reporting for Call Center, please do the following. 1. On the Windows taskbar, click Start, point to Settings and then click Control Panel. The Control Panel window appears. (On some versions of Windows you can click Start, point to Settings and then click Control Panel. 2. Click on Add/Remove Programs. 3. Uninstall Reporting for Call Center Note: You DO NOT need to uninstall the MySQL Servers and Clients 3.23.53, nor the Java 2 Runtime Environment SE v.1.4.0_03. If required, your Nortel Networks Reporting for Call Center databases will be modified during the installation. There will be no loss of statistical data, but new data, tables, columns and/or indexes may be added to them. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Introduction 9 Deleting Temporary Internet Files To prevent Internet Explorer from cacheing old versions of the Nortel Networks Reporting for Call Center web pages, you should delete the temporary internet files that are on your computer. Click on Start, then right click on the Internet Explorer icon, and select Internet Properties. The Figure 1 Internet Properties Window Note: If you do not see this window you have clicked on a shortcut to Internet Explorer. You must click on the Internet Explorer icon in the Start menu. When you see the window shown in Figure 1, click on the Delete Files button. The Delete Files dialog shown in Figure 2 will appear. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 10 Installation Figure 2 Delete Files Dialog Select the Delete all offline content option, and then click on the OK button. You may then click on the OK button to close the Internet Properties window. You may now proceed with the installation of Nortel Networks Reporting for Call Center, as detailed below. Installation prerequisites Before you install Nortel Networks Reporting for Call Center software, you must: 1. Be familiar with the Call Center and the WindowsTM operating system used by your Web Host PC. 2. Ensure that the Call Center is installed and configured. 3. Ensure that the Call Center platform is connected to, and is operational on, the network to which the Nortel Networks Reporting for Call Center Web Host PC is connected. 4. Ensure that Microsoft Internet Information Services is installed and operational on the Web Host PC, and that the Default Web Site is enabled. Microsoft Internet Information Services can be installed through Add/Remove programs, using the Add/Remove Windows Components icon. Note that on Windows NT you must upgrade Internet Information Services to Version 4. This is available on the Windows NT Options pack CD. To ensure correct operation of Nortel Networks Reporting for Call Center the following points must be observed. • The IP address setting for the default website should be ‘(All Unassigned)’ or the IP address setting for the default website should be 127.0.0.1 and the host header should be localhost. • The port should be set to 80. • Ports 3500, 6010 and 6011 must not be blocked by local firewalls. ! It is recommended that you ensure that you have made your Web Host PC Internet Information Services installation as secure as possible. Generally this involves loading security patches and/or service packs for Internet Information Services and for the operating system of the Web Host PC. These are made Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Introduction 11 available free of charge by Microsoft. Contact your network Administrator for further advice. Now you are ready to install the Nortel Networks Reporting for Call Center software from the Call Center platform. ! You must have Administrator’s rights for the installation to be successful. If you do not have Administrator’s rights for the PC on which you wish to install Nortel Networks Reporting for Call Center, the installation will be halted and you will be requested to log out and log back in with Administrator’s rights. Installing Nortel Networks Reporting for Call Center software By default, Nortel Networks Reporting for Call Center software creates a folder called \Program Files\Nortel Networks\Nortel Networks Reporting for Call Center on the installation drive of the Web Host PC. This folder contains the application files used by Nortel Networks Reporting for Call Center. It also contains the Nortel Networks Reporting for Call Center configuration and statistical database. Note: Before Nortel Networks Reporting for Call Center will operate correctly, you must enable the Call Center Reporting Software Keycode. For Software Keycode information, refer to the Software Keycode Installation Guide. TCP/IP Protocol The Call Center platform and Nortel Networks Reporting for Call Center use the industry standard TCP/IP protocol for communication between the Call Center and the Nortel Networks Reporting for Call Center Web Host PC. This means the Windows Network component is required for the Nortel Networks Reporting for Call Center Web Host PC. The Nortel Networks Reporting for Call Center installation process does not install the Windows Network component. For instructions on installing the Windows Networking component, refer to your network or Windows documentation. Checking whether the Windows Networking Component Is Installed To check that the Windows Network component is set up properly on a PC in order for it to operate as a Web Host PC, the following steps must be performed: Note: If your company has a network administrator, check with your administrator before changing any network configuration parameters. 4. Start the Windows system on the PC that will have the Nortel Networks Reporting for Call Center application installed. 5. On the Windows taskbar, click Start, point to Settings and then click Control Panel. The Control Panel window appears. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 12 Installation (If you are using the Windows 2000 operating system, double click instead on Networking and Dial-up Connections. The Networking and Dial-up Connections window appears) (If you are using the Windows XP operating system, point to Start, Connect to and then click on instead on Show All Connections. The Networking Connections window appears) 6. Double click on the Network Configuration tab displayed. icon . The Network window appears with the (If you are using the Windows 2000 or Windows XP operating system, right click on the Connection icon and then click on Properties.) Local Area 7. Check that TCP/IP appears on the list of installed network components. If TCP/IP is not on the list, click Add to install this protocol using the Windows installation instructions, or refer to your network administrator. Installing Nortel Networks Reporting for Call Center For a Business Communications Manager Installation Exit any Windows programs that are running. Start your internet Browser (such as Internet Explorer or Netscape), and use it to connect to the Business Communications Manager. Do this by entering into the browser Address Bar the IP Address of the Business Communications Manager in the following format: https://10.10.10.1/. (Remember to substitute the IP Address of your Business Communications Manager for the 10.10.10.1 shown in the example above.) Nortel Networks Unified Manager page will appear in the browser. Click on the Install Clients link. The Install Clients page will appear in the browser. Click on the Nortel Networks Reporting for Call Center link. Information on the Nortel Networks Reporting for Call Center application will appear in the browser window. (You may need to scroll down through the page to see the button which install the application.) Click on the Nortel Networks Reporting for Call Center button. A dialog will appear from which you can select to either Run this program from its current location or Save this program to disk. The default option is Save this program to disk. Click on OK. The dialog box shown in Figure 2 on Page 13 will appear. Please wait. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Introduction 13 For a CallPilot Installation Exit any Windows programs that are running. Insert the Application Installation CD into the CD drive of the PC you wish to use as the Web Host PC. Double-click on the Setup.exe file. The dialog box shown in Figure 3 on Page 13 will appear. Please wait. Figure 3: InstallShield Initialization Dialog The Extracting Files dialog shown in Figure 3 prepares the installation files required to install the Nortel Networks Reporting for Call Center files on the Web Host PC. Figure 4: Language Selection Dialog Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 14 Installation The dialog shown in Figure 4 This dialog allows you to select the default language for your installation of Nortel Networks Reporting for Call Center. Note that the Users of Nortel Networks Reporting for Call Center are each allocated a language, so that you can have different languages in use by various Users at the same time. This dialog allows you to define the default language for the Log In Page, and for the default Administrator. When you have selected your language, click on the OK button. If you wish to stop the installation, click on the Cancel button. You will then be presented with the InstallShield Windows Installer Configuration Dialog shown in Figure 5 prepares the Wizard which is required to install the Nortel Networks Reporting for Call Center files on the Web Host PC. Figure 5: InstallShield Windows Installer Configuration Dialog If you click on the OK button you will be presented with the dialog shown in Figure 4. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Introduction 15 Figure 6: InstallShield Wizard Start Dialog The dialog shown in Figure 6 is the Welcome dialog. If you wish to cancel the installation procedure, click on the Cancel button. To proceed, click on the Next button. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 16 Installation Figure 7: License Agreement Dialog The dialog shown in Figure 7 is the License Agreement dialog. Please read the Software License Agreement before proceeding. To proceed with the installation you must click the Yes button. To cancel the installation click on the No button. To return to the Welcome dialog, click on the Back button. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Introduction 17 Figure 8: Customer Information Dialog If you clicked the Yes button in the License Agreement dialog shown in Figure 4, you will be presented with the dialog shown in Figure 8. This is the Customer Information dialog. Enter your user name in the User Name field. Enter the Company Name in the Company Name field. When you have entered these fields, the Next button will become available. Until you have entered these fields the Next button is greyed out. To proceed with the installation click the Next button. To cancel the installation click on the Cancel button. To return to the License Agreement dialog, click on the Back button. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 18 Installation Figure 9: Choose Destination Location If you clicked the Next button in the Customer Information dialog shown in Figure 8, you will be presented with the dialog shown in Figure 9. This is the Choose Destination Location dialog. If you do not wish to install Nortel Networks Reporting for Call Center on the default drive (C:) click the Browse button and choose a new destination. To proceed with the installation click the Next button. To cancel the installation click on the Cancel button. To return to the Customer Information dialog, click on the Back button. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Introduction 19 Figure 10: Setup Status Dialog If you clicked the Next button in the Choose Destination Location dialog shown in Figure 9, you will be presented with the dialog shown in Figure 10. This is the Setup Status dialog. This shows the progress of the installation. If you wish to cancel the installation click the Cancel button. If you wish to proceed with the installation please wait for the installation to complete. Presently you will see the message shown in Figure 11 displayed. Figure 11: Database Installation Dialog This informs you that the installation has proceeded to the stage where the MySQL database is being installed. (The MySQL database is not installed into the same folders as Nortel Networks Reporting for Call Center, it is installed into \mysql on the target hard drive.) Please wait. Presently you will see the message shown in Figure 12 displayed. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 20 Installation Figure 12: Java Installation Dialog This informs you that the installation has proceeded to the stage where the Java Runtime is being installed. (The Java Runtime is not installed into the same folders as Nortel Networks Reporting for Call Center, it is installed into \program Files\Java on the target hard drive.) Please wait. Presently you will be presented with the Installation Complete dialog, shown below in Figure 13. Figure 13: Installation Complete Dialog Before Nortel Networks Reporting for Call Center can operate correctly, your Web Host PC must be rebooted. To have the installation reboot your PC straightaway, click the Yes, I want to restart my computer now radio button, and then click the Finish button. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Introduction 21 To complete the installation without rebooting your PC at this time, click the No, I will restart my computer later radio button, then click the Finish button. Call Center Reporting Server If your Call Center Platform is a CallPilot, you will also need to install the Call Center Reporting Server onto a PC. Typically this will be the PC you will use as the Master Web Host. Note: You DO NOT need to perfom this installation if your Call Center platform is a Business Communications Manager. 1. Load the CallPilot 100/150 CD in the CD-ROM drive of your computer. 2. Inside the CD folder double-click the Optional Software folder. 3. Inside the Call Center Application Server folder double-click setup.exe. The Welcome screen appears. 4. Click the Next button. The License Agreement screen appears. 5. Click the Yes button to accept the license agreement. The folder selection screen appears. 6. We recommend you install the reporting server in the default folder shown. Click the Next button. The database folder screen appears. 7. We recommend you install the database in the default folder shown. Click the Next button. If you do not have the Microsoft SQL Desktop Engine (MSDE) installed on your computer, a message appears that asks if you want to install it. 8. If you have MSDE installed, go to step 9. If you do not have MSDE installed, click OK and wait until it is installed. If you do not have Microsoft .NET Framework installed, a message appears that asks if you want to install it. 9. If you have Microsoft .NET Framework installed, go to step 10. If you do not have Microsoft .NET Framework installed, follow the information on the next six screens to install it. A message appears that says that the Call Center Reporter Server configuration tool will now launch. 10. Click the OK button. 11. On the Call Center Reporting Server Config screen: a) In the CallPilot address box your local host address automatically appears. Change this address to the IP address or Fully Qualified Domain Name of your CallPilot. b) If you have a Call Center reporting application installed on the same PC as the Call Center Reporting Application Server software, you must change the HTTP Listen Port Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 22 Installation value from its default (80), by entering the number of the port you want to use. If your reporting application is installed on a different PC, you can leave the value at its default of 80. If you do not know which port to use, ask your installer. c) We recommend you do not change the values for the Control, Real-Time or Historical Ports Click the OK button. The Setup Complete screen appears. 12. Click the Finish button. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Administration 23 4 Administration Logging In Using Internet Explorer, browse to the URL of your Nortel Networks Reporting for Call Center Web pages Log In page. The URL will be http://NameOfWebHostPC/RCC/index.asp Where NameOfWebHostPC should be replaced with the network name or IP Address of the Web Host PC. Note: If you are actually using the browser on the Web Host PC NameOfWebHostPC can be substituted with ‘localhost’. Note: Once you have successfully browsed to the Log In page, you might like to add this location to your Internet Favourites. This can be accomplished in Internet Explorer by pressing Ctrl-D when you are on the Log In page, or by clicking on Favourites, Add to favourites… When you have logged in you will be presented with the page below. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 24 Administration Figure 14 Log In page Note: A System Administrator is already set up for you, with a default password. You will be required to change this password the first time you login. Enter the username admin and the password 0000 and click on the Login button. You will be presented with the Change Password page, shown below. Changing Default Password Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Administration 25 Figure 15 Change Password Page Choose a new password. The password can be from 1 to 10 characters, including upper and lowercase letters, and digits. It can be anything apart from 0000. Enter your new password in the New Password field, and then enter the same password in the Confirm password field. If there were any differences between the two entries you will be informed that the password and confirmation do not match, and you will need to re-enter the password in both fields once more. If you have successfully entered the new password correctly in both fields you will be presented with the Administration Menu page, shown below. Administration Menu The Administration Menu is the page an Administrator will be presented with whenever they login (unless they are logging in with a default password of 0000). Note: To remind you that you have logged in as an Administrator, the word ‘Administration’ is displayed on the right hand end of the blue bar at the top of each Administration page. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 26 Administration Figure 16 Administration Menu Page The options that are available to an Administrator are listed down the left hand side of the page. These will be described in turn below. Call Center Connection The Call Center Connections option allows you to specify the network identifier (IP Address or Network Name) of the Call Center platform. When you select the Call Center Connection option you are presented with the Call Center Connection page, shown below. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Administration 27 Figure 17 Call Center Connection Page Enter the IP Address or the Network Name of the Call Center platform. If you do not know what to enter here, consult the Local Area Network Administrator for your site. ! If you are entering the connection details for the PC on which the CallPilot 3.0 Application Server is running, you must also specify the Port number for which the Application Server has been configured. This is indicated by entering the IP Address, a colon and then the Port number. For example, If the IP address number was 10.1.1.150 and the Port number was 8079, the full entry in this field would be the 10.1.1.150:8079. When Nortel Networks Reporting for Call Center communicates with the Call Center to request Real Time or Historical Report data it includes a password in the data request. This allows the Call Center to verify that the application requesting the data is authorized to receive it. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 28 Administration This password is set within the Call Center using CallPilot Manager. That same password must be entered into the CCRS password field. It must then be entered into the Confirm CCRS password field. Note: The default CCRS password is ‘CCRS’, but this might have been changed within the Call Center from within CallPilot Manager. The Connection Security radio buttons allow you to specify whether you are connecting to the Call Center using HTTPS or HTTP. By default, this connection is HTTPS. If it is changed on the Call Center platform to HTTP you must also change this setting to HTTP. This is an advanced setting that is not usually changed from the default. When you change the Connection Security setting you will see a popup message informing you that you must reboot your Web Host PC in order for the settings to take effect. Figure 18 Connection Security Setting Changed Reboot Message As indicated in the message box shown above, you must close down and restart the Web Host PC before these changes will take effect. The Make data requests every dropdown allows you to specify how frequently the Web Host PC communicates with the Call Center in order to obtain reporting data. It is usual to set this to 15 minutes. The Select An IP Address field allows you to select which IP Address (Network Interface Card) you wish to use to communicate to the wallboards with. If the Web Host PC has more than one IP Address (because it has more than one Network Interface Card configured) the drop down menu will be populated with the IP Addresses that have been configured for the Web Host PC. This allows you to select which Network Interface Card to use for communication with the wallboards. The Network Interface Cards are identified in the drop down menu by their configured IP Addresses. You should select the IP Address which has been configured on the Network Interface Card which is connected to the same network as the wallboards. Note that this is NOT the IP Address of the wallboard – this is the IP Address that has been configured for the Network Interface Card in the Web Host PC. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Administration 29 ! Note that if you add a new Network Interface Card or other network type of device, such as a USB Bluetooth device, or if you enable a disabled Network Interface Card, then you must reboot your Web Host PC in order for the new device to be detected and presented to you in the Select An IP Address dropdown menu. When you click on the Submit button on the Call Center Connection page (see Page 22 of the Reporting for Call Center SUOG) you will see a popup message informing you that the data download might take some time, and to please await further notification. Figure 19 Starting Data Download notification Message When you click the OK button the message box will close and Reporting for Call Center will repeatedly request historical data from the Call Center until the database on the Web Host PC is up to date. A small window will appear which will show an updated display to allow you to monitor the progress of the Call Center download. Figure 20 Download Status Window This window provides information regarding the status of the current download. The Percentage Completed line indicates how near to completion the download is. When Reporting for Call Center is installed it queries the Call Center for any Call Center data that the Call Center has accumulated. The oldest data that is held within the Call Center database defines the start point of the download, and the date of ‘today’ defines the end point of the download. The download has to request data from the Call Center for each day within the download period. The Percentage Completed line indicates how far through the download period the download process has reached in terms of time, not in terms of calls. For example, if the Percentage Completed figure was at 50% and the Calls Extracted from Received Data was at 125, this does not mean the download will be complete when the Calls Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 30 Administration Extracted from Received Data reaches 250. Rather, it means that the download has processed 50% of the download period and has extracted 125 calls so far. Total Call Center Calls in the Database indicates the total amount of calls stored within the Web Host PC database, which will include the Calls Extracted from Received Data figure. Note: The time taken to download the historical data from the Call Center and to store it in the Web Host PC database will depend on the amount of time the Call Center has been recording historical data prior to being connected to the Web Host PC, and the amount of call traffic that your Call Center handles. As a rough guide, 30,000 calls will take between 6 and 18 hours, depending on the level of network traffic and the speed of your Web Host PC. You may use your PC as normal during this period of course, but do not reset it or power it off. When the download has completed you will be informed by another message box. Note: If you have changed the Browser Web Page to something other than the Call Center Connection page, or if you have closed the Browser, then you will not receive the download completed message. The data download will complete as expected, and you will be informed of this in the Download Status Window, but you will not receive another message box from the Browser. Note: If the Browser page has timed out by the time the data download has finished, this is not an error. Microsoft Internet Information Services has a setting which dictates how long it will wait before closing a web page. The data download will complete as expected, and you will be informed of this in the Download Status Window, but you will not receive another message box from the Browser. System Administration Selecting the System Administration option presents you with the System Administration Menu page, shown below. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Administration 31 Figure 21 System Administration Menu Page The System Administration Menu allows you to: • • • Change the username and the password for the default Nortel Networks Reporting for Call Center Administrator To create Users To allocate Skillsets to those Users System Admin Settings Note: This is a special utility to allow you to amend the settings for the single, pre-defined Administrator that is supplied ready-defined with Nortel Networks Reporting for Call Center. This is NOT the way to change the username and password of other Users who have been configured as Administrators. To change the details of those Administrators, use the User Admin Edit feature, described on Page 36. On the System Administrator page you can change the name of the System Administrator or change their password, or both. In either case you must enter the current System Administrator password to confirm that you have authority to make these changes. Selecting the System Admin Settings option presents you with the System Administrator details page, shown below. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 32 Administration Figure 22 System Administrator details page To change the name of the System Administrator provide a new name in the username field, and the current Administrator password in the old password field. To change the password provide the new password in the new password field, and confirm the password by entering the same password in the confirm new password field. (You must also provide the old (that is, the current) password in the old password field.) When you have made the changes you need to, click on the Submit button. You will be returned to the System Administration Menu page. User Admin This option allows you to Add, Delete, Edit the settings or Reset the password for a User. Note: A User is not an Agent! A user is someone that you wish to have access to the Nortel Networks Reporting for Call Center system, in order to monitor Skillsets through the Real Time screens and to be able to obtain Historical Reports on those Skillsets. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Administration 33 You do not have to enter all of your Call Center Agents into Nortel Networks Reporting for Call Center (although you can, if you so wish). Typically, you would enter Skillset Supervisors and other Management personnel who need to know about the performance of the Call Center. Selecting the User Admin option presents you with the user Admin page, shown below. Figure 23 User Admin Page The first time you see this page there will be no Users defined. To add users click the Add button. You will be presented with the Add User page, shown below. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 34 Administration Figure 24 Add User Page This page allows you to enter the details of the new User. You provide the first name and the surname of the User, and the username they will use to log in to Nortel Networks Reporting for Call Center with. You can specify the language preference of the User, which will dictate the language used to display the Nortel Networks Reporting for Call Center Web Pages to them. Finally, you can specify whether the new User is able to configure wallboards (for their assigned Skillsets), and whether they are a regular User or an Administrator. Note 1: You should only make a User an Administrator if it is required for that individual to be able to specify and change fundamental configuration settings within Nortel Networks Reporting for Call Center. Note 2: All new Users have their passwords defaulted to 0000. The first time they login to Nortel Networks Reporting for Call Center they are prompted to change their password. In the example shown below, the new user Mary Smith has been added, with the Username of MaryS, she is going to receive the Web Pages in English and whilst she is able to configure wallboards for her assigned Skillsets, she is not a full Administrator. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Administration 35 Administration and User Permissions The System Administrator, Users created as Administrators, Users who can Assign Wallboard and Standard Users have different administration capabilities regarding other Users, Skillset Assignment and Wallboard Assignment. Regular Users (Standard Users) These are Users who have been created without either the Administrator or the Assign Wallboards check boxes ticked. These Users can perform no configuration of other Users, and they cannot change their own settings. They also cannot assign or work with Wallboards. Regular Users only have access to the Skillsets that were assigned to them by the System Administrator. Users with the Assign Wallboard Box Checked (Wallboard Users) These are Users who have been created without the Administrator check box ticked. These Users can perform no configuration of other Users, and they cannot change their own settings. They can assign and work with Wallboards. Wallboard Users only have access to the Skillsets that were assigned to them by the System Administrator. Users with the Administration Box Checked (User Administrators) These are Users who have been created with the Administrator check box ticked. These Users can perform configuration and editing activities on other Users, including creating Users and assigning Skillsets to them. They cannot change their own settings however, apart from resetting their own password. If the Wallboard check box was ticked when their own account was originally created they are also able to assign and work with Wallboards. User Administrators only have access to the Skillsets that were assigned to them by the System Administrator. System Administrator This is the default Administrator account which is created when Nortel Networks Reporting for Call Center was installed. This User has full access to the system and to all configuration options. They can create and edit and delete Users, and can assign Skillsets to them. They can also reset User passwords, including the System Administrator’s password. Note that they are the only user who can do this. The System Administrator has access to any Skillset. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 36 Administration Figure 25 Details for new User Mary Smith When you have completed the details of your new User, click on the Submit button. This will save the details of the newly entered User. A small dialog box will ask whether you wish to add more Users. If you choose to Add more users the Add User page fields are cleared and you can enter the details of your next new User. If you decide not to add any more Users at this time you are returned to the User Admin page. The newly added User will now be listed on the User Admin page. Beside the user details are some buttons. These allow you to Edit the details of the user, to Delete the User from the system entirely or to Reset their password to 0000, should they have forgotten their password. Edit This button will present you with the Edit user page, shown below. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Administration 37 Figure 26 Edit User Page This is similar to the Add User page but the User detail fields are already populated with the currently stored details for the User. Delete Use this option to remove the details of a User completely. Note: If you Delete a User and subsequently wish that you hadn’t, you will have to Add the User again by using the Add User page and entering their detail once more. When you click the Delete button you will be prompted to make sure that you wish to remove the User. If you do not wish to remove the User click the Cancel button, if you are sure you wish to remove the User click the OK button. In both cases you will be returned to the User Admin page, but if you decide to remove the User they will no longer be included in the list of configured Users. Reset Password This button allows you to reset the password of the User to 0000. This will mean that the User must use the password 0000 when they next login, and they will be forced to select a new password. Use this option when a User has changed their password to something and then forgotten what it was. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 38 Administration When you click the Reset Password button you will be prompted to make sure that you wish to reset the password for the User. If you do not wish to reset their password click the Cancel button, if you are sure you wish to reset their password, click the OK button. In both cases you will be returned to the User Admin page, but if you decide to reset their password they will need to use the password 0000 the next time they login. They will then be prompted to enter a new password. Skillset Assignment This option allows you to assign Skillsets to Users. Assigning Skillsets to a User allows the User to view those Skillsets in the Real Time screens and to obtain Historical Reports on those Skillsets. A User can have multiple Skillsets assigned to them, and a Skillset can be assigned to multiple Users. Selecting the Skillset Assignment option presents you with the Skillset Assignment page, shown below. Figure 27 Skillset Assignment Page Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Administration 39 Each configured user is listed on this page. In our example we only have one configured User, Mary Smith. Beside the entry for Mary Smith there is a button labelled Assign. Clicking the Assign button presents you with the Assigned Skillsets page, shown below. Figure 28 Assigned Skillsets Page Note 1: The Skillset names shown here are intended as examples only. Your copy of Nortel Networks Reporting for Call Center will display whatever Skillset names you have setup in the Call Center using CallPilot Manager. Note 2: The Skillset names are obtained automatically from the Call Center. Your copy of Nortel Networks Reporting for Call Center will have to have been connected to the Call Center for a few moments in order for the Skillset names to appear here. The Skillsets are assigned by moving them from the Unassigned Skillsets list to the Assigned Skillsets list. This is accomplished by highlighting the Skillset name you wish to assign (in the Unassigned Skillsets list) and clicking on the > button. This will move the Skillset from the Unassigned Skillsets list to the Assigned Skillsets list. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 40 Administration Repeat this until you have assigned all the Skillsets you wish to assign to this User. In the example shown below the User Mary Smith has been assigned three Skillsets: Development, Sales and Training. Figure 29 Skillsets Assigned to User Mary Smith To unassign a Skillset, simply highlight it in the Assigned Skillset list and click on the < to move the highlighted Skillset back to the Unassigned Skillsets list. The >> and << buttons will assign or unassign all of the Skillsets in a single mouse-click. Holding down the Control (CTRL) key and clicking different Skillset names will allow you to highlight and select a selection of the Skillsets in the Unassigned Skillsets list. Clicking once on the > button will then assign those selected Skillsets in one step. Likewise, holding down the Control key and clicking different Skillset names will allow you to highlight and select a selection of Skillsets in the Assigned Skillsets list. Clicking once on the < button will then unassign those selected Skillsets in one step. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Administration 41 When you have assigned the Skillsets you wish this User to have access to, click the Submit button. You will be returned to the Skillset Assignment page. Reporting The Reporting option presents you with the Main Menu page, shown below. This is the page all regular Users (that is, non-Administrative Users) are presented with when they login. This option allows an Administrator to use the Nortel Networks Reporting for Call Center as though they were a User, to view Real Time screens and to access the Historical Reports. Maintenance The Maintenance option allows you to check the System Status and to start or stop the XML data feed logging. When you select the Maintenance option you are presented with the Maintenance Menu page, and the Maintenance menu options appear below the main Maintenance heading. This is shown below. Figure 30 Maintenance Menu Page Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 42 Administration System Status Selecting the System Status option presents you with the System Status page, shown below. Figure 31 System Status Page The System Status page shows a variety of information relating to the current status of Nortel Networks Reporting for Call Center. You would normally only need to refer to this page when under the instruction of Support Personnel. Logging Selecting the Logging option presents you with the Logging Menu page, shown below. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Administration 43 Figure 32 Logging Menu Page The Logging Menu page contains a window which lists logging activity information, and two buttons. Various diagnostic logs are always running whenever Nortel Networks Reporting for Call Center is operational. The Logging Menu window allows you to start or stop one of the diagnostic logs. This log captures the XML data sent from the Call Center to Nortel Networks Reporting for Call Center. You would only normally stop this log under the instruction of Support Personnel. The Clear Log Window button erases any text from the Log Data Window. It does not affect the current state of logging. If the XML data logging is on, the first button will be labelled Deactivate Logging. Clicking this will cause the logging to stop, as shown below. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 44 Administration Figure 33 Logging Menu Page, with the Logging Stopped When the logging is stopped, the button is re-labelled with Activate Logging. Clicking the button in this state will start the logging. Company Details Selecting the Company Details option presents you with the Company Details page shown below. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Administration 45 Figure 34 Company Details Page This page allows you to enter the details of your company or site. Completing this page is not a requirement for the correct operation of Nortel Networks Reporting for Call Center, it is purely a means of recording where the software is installed. Reporting The Reporting option presents you with the Main Menu page, shown below. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 46 Administration Figure 35 Main Menu Page This allows you to use the application exactly as if you had logged in as a User. (This is the first page a non-Administrative User will see when they log in). Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Using Reporting For Call Center 47 Using Reporting for Call Center 5 Logging In Using Internet Explorer, browse to the URL of your Nortel Networks Reporting for Call Center Web pages Log In page. The URL will be http://NameOfWebHostPC/rcc/index.asp Where NameOfWebHostPC should be replaced with the network name or IP Address of the Web Host PC. Note: If you are actually using the browser on the Web Host PC NameOfWebHostPC can be substituted with ‘localhost’. Note: Once you have successfully browsed to the Log In page, you might like to add this location to your Internet Favourites. This can be accomplished in Internet Explorer by pressing Ctrl-D when you are on the Log In page, or by clicking on Favourites, Add to favourites… When you have logged in you will be presented with the page below. Figure 36 Log In Page Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 48 Using Reporting for Call Center You must provide a valid username and a password in order to gain access to the features of Nortel Networks Reporting for Call Center. Before you attempt to login, ensure that an Administrator has created a username for you. The first time you log in your password will be set to the default value of 0000. In the username field type the Username you have been allocated, and in the Password field enter the default password of 0000. You must change your password the first time you login. You will be resented with the Change Password page shown below. Figure 37 Change Password Page Choose a new password. The password can be from 1 to 10 characters, including upper and lowercase letters, and digits. It can be anything apart from 0000. Enter your new password in the New Password field, and then enter the same password in the Confirm password field.. If there were any differences between the two entries you will be informed that the password and confirmation do not match, and you will need to re-enter the password in both fields once more. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Using Reporting For Call Center 49 If you have successfully entered the new password correctly in both fields you will be presented with the Main Menu page, shown below. This is the page you will be presented with for all future logins. Figure 38 User Main Menu Page This is the Main Menu for all regular (non-Administrator) Users. Note that the word ‘Administrator’ is not displayed on the right hand end of the blue bar at the top of each page. Also note that Nortel Networks Reporting for Call Center recognises who has just logged in, and it greets them accordingly. In our example shown above User ‘Mary Smith’ has logged in, and the page displays the message ‘Welcome Mary’. The options that are available to Users are displayed on the left-hand side of the Main Menu page. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 50 Using Reporting for Call Center Time Bins Setup This option allows you to specify the settings for the Answer and Abandon Time Bins, for the Skillsets which have been assigned to you. Answer and Abandon Time Bins are collectively known as the Time Bins. Answer Time Bins The Answered Time Bins are a series of six time steps used in the statistical analysis of Answered Calls. Nortel Networks Reporting for Call Center will provide statistical reports on the percentage of incoming calls answered within each of the periods specified in the chosen Answered Time Bins. A seventh Answer period is also used in the reports, which gathers information on all calls which were answered after the period specified by the sixth Answered Time Bin. Abandon Time Bins The Abandon Time Bins are a series of six time steps used in the statistical analysis of Abandoned Calls. Nortel Networks Reporting for Call Center will provide statistical reports on the percentage of incoming calls abandoned within each of the periods specified in the chosen Abandoned Time Bins. A seventh Abandoned period is also used in the reports, which gathers information on all calls which abandoned after the period specified by the sixth Abandoned Time Bin. Note: If other Users have been assigned these Skillsets, they can change these settings. Selecting the Time Bins Setup option presents you with a single menu option (Time Bins Setup), and the Time Bins Setup Menu page, shown below. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Using Reporting For Call Center 51 Figure 39 Time Bins Setup (Configuration) Menu Page Selecting the Time Bins Setup option presents you with the Time Bin Setup page, shown below. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 52 Using Reporting for Call Center Figure 40 Time Bin Setup Skillset Selection page The Time Bin Setup Skillset selection page allows you to select a Skillset you wish to set Time Bin values for. Note that the list of available Skillsets for our Example User Mary Smith only contains those Skillsets assigned to her by the Administrator. Click on any of the displayed Skillsets to highlight the Skillset you wish to set the Time Bin values for, and then click on the Assign Time Bins button. You will be presented with the Time Bins values page, shown below. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Using Reporting For Call Center 53 Figure 41 Time Bins Page This page allows you to enter the time steps required to define the periods into which you wish to have calls that are Answered or Abandoned in these Skillsets categorized. The steps used in the Time Bin periods need not be the same, but the Time Bin periods must be set in ascending order. For example, if you want to have Nortel Networks Reporting for Call Center report on Answered calls, grouping together the calls that were answered within 10 seconds, the calls that were answered between 10 and 20 seconds, the calls that were answered between 20 and 30 seconds, the calls that were answered between 30 and 40 seconds, the calls that were answered between 40 and 50 seconds, the calls that were answered between 50 seconds and one minute, you would set the Time Bins up to be: 00:10, 00:20, 00:30, 00:40, 00:50 and 01:00. Note that Nortel Networks Reporting for Call Center would also include a category for anything greater than the last time period, which in this example would be ‘anything answered after 01:00’. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 54 Using Reporting for Call Center To save the settings you have made, click the Submit button. You will be returned to the Time Bin Setup Menu page. To leave the Time Bins page without saving any changes you might have made, click the Cancel button. You will be prompted to confirm you do not wish to save your changes. You will then be returned to the Time Bin Setup Menu page. Print Schedules Print Schedules configure Nortel Networks Reporting for Call Center to automatically print the a set of requested reports, at a specified time. You can specify Print Schedules to print either Daily, Weekly or Monthly reports. You can configure multiple Daily, weekly and Monthly Schedules. For example you may wish to run off a set of reports each day before you come in, which refer to Call information. You would accomplish this by configuring a Daily Schedule which prints at, say, 08:00. You may also have a different Daily Schedule report which refers to Agent Activity, and configure Nortel Networks Reporting for Call Center to print these reports at, say, 16:30 so that you have time to review them before the end of the day and the departure of your Agents. Note: If the Web Host PC is powered off over the period in which the Schedule print is due to take place, the Schedule Print will not be produced. You can easily obtain the same reports by using the Reports options (see the Report section, on Page 125). Note: If you select the Agent Audit Report, the Activity Code Report by Skillset, Agent Activity Code Report by Agent or the Activity Code Report by # of Pegs Reports to be included in your Print Schedule, you will be further prompted for the Agents and/or the Activity Codes you wish to have included within these Reports. These further steps are described on Pages 156 (Agent Audit Report), 161 (Activity Code Report by Skillset), 165 (Activity Code Report by Agents) and 169 (Activity Code report by # of Pegs). Selecting the Print Schedules option presents you with the Print Schedules page, shown below, with the various Print Schedule options displayed on the left-hand edge of the page, beneath the main Print Schedules heading. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Using Reporting For Call Center 55 Figure 42 Print Schedules Page Daily Schedules Selecting the Daily Schedules option presents you with the Your Daily Schedules page, shown below. Initially this will be empty. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 56 Using Reporting for Call Center Figure 43 Your Daily Schedules Page To add a Daily Schedule, click the Add button. Clicking on the Add button presents you with the Add Daily Schedules page, shown below. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Using Reporting For Call Center 57 Figure 44 Add Daily Schedule Page The Add Daily Schedule page allows you to specify the which reports you wish to have included in the Schedule, which days are to be included in the Schedule and when it is to be printed. You may also specify which period of the day the reports will contain. You must also specify a name for your Schedule and which printer you wish to have the reports generated on. To select a report to be included in the Schedule, click the check box beside the report name. Selected reports will have a tick in the check box beside their name. You can of course select multiple reports. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 58 Using Reporting for Call Center To include the reports from a particular day in the Schedule, click the check box beside the day to place a tick in the check box. You can of course select multiple days. Note: Daily Reports print on the day following the day which is being reported on. That is, if you select a Daily Report Schedule for Monday, it will be printed on Tuesday. This ensures that the report day has completely elapsed when the reports are generated. To set a name for your Schedule, type the name in the Schedule Name field. This is to help you identify, and distinguish between, the different Schedules you create. The Report Period Start Time and Report Period End Time dictate the period within each day for which the reports are generated. For example, if your Call Center has a working day that starts at 08:30 and finishes at 17:30, you may wish to specify the Start Time as 08:00 (to see if you have early calls that you are missing by not having the Call Center open) and 18:00 (to see if there is a late surge of calls). To specify which printer the reports will be generated on, select one of the options from the Select printer drop-down menu. This drop-down menu will list all of the printers which are accessible from the Web Host PC. (The reports are generated from the databases held in the Web Host PC.) Our example User Mary Smith has configured her Daily Schedule as shown below. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Using Reporting For Call Center 59 Figure 45 Add Daily Schedule Page - Example Settings Mary Smith has selected the Answered Calls, Abandoned Calls and CLID reports to be printed at 08:30 each morning, for Monday through to Friday. (So her printouts will be generated on Tuesday for Monday, on Wednesday for Tuesday, and so on until Friday’s reports are printed on Saturday morning.) Her schedule is Called AnswAband, and the reports will start to be generated at 08:30, on the HP 840C DeskJet printer. The reports will cover the period from midnight to midnight for each day. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 60 Using Reporting for Call Center To save your Daily Schedule click on the Submit button. You will be presented with the Daily Schedule – Skillsets page, shown below. To leave the Add Daily Schedule page without saving any changes you might have made, click on the Cancel button. You will be presented with the Your Daily Schedules page. Figure 46 Daily Schedule Skillsets Page The Daily Schedule Skillsets page allows you to select which Skillsets you wish to have included within the generated reports that are produced by the Daily Schedule. Skillset List Selection Methods You can use the following techniques to select Skillsets from the Skillset List. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Using Reporting For Call Center 61 Clicking once on an unselected Skillset name will select it (it will be highlighted) and will remove the highlight from any other currently selected Skillsets. Clicking once on a selected (highlighted) Skillset name will unselect it. But note that if other Skillsets are selected and you click on a Skillset name, you will unselect all of the other Skillsets and you will select the Skillset you clicked on. Clicking with the Control key (CTRL) pressed will allow you to select and highlight multiple Skillsets. Clicking a Skillset with a Shift key held down will highlight all of the Skillsets between position of the currently highlighted Skillset and the Skillset you clicked on. The Select All button can be used to select and highlight all of the Skillsets at once. Adding Selections to the Favourites List If there are collections of the assigned Skillset which you will frequently need to review the Daily Schedules for, you can add the selection of Skillsets to the Favourites list. This will mean that instead of having to select and highlight a particular collection of Skillsets each time you wish to use them, you can just click the Select button beside appropriate Favourite and the collection of Skillsets will be highlighted for you at once. To add a Favourite to the Favourite List, highlight the Skillsets you wish to include in the Favourite and then click the Create Favourite button. You will be presented with the Save Favourites page, shown below. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 62 Using Reporting for Call Center Figure 47 Save Favourites Page Enter a name in the Favourite Name field, and then click on Submit to save it. (Click on Cancel to return without saving the Favourite.) Mary Smith has created a Favourite that contains the Skillsets Training and Development, and she has called the Favourite Dev&Train. When a Favourite has been created it will appear in the Favourite List at the top of the page, as shown above. Note: Many pages within Nortel Networks Reporting for Call Center allow you to use Skillset selection lists and Favourites, and the techniques described here apply to all of those other pages too. All the Favourites you create will be accessible from any point within Nortel Networks Reporting for Call Center which allows you to use Favourites. Mary Smith has clicked on the Select button beside her new Favourite (Dev&Train) and the two associated Skillsets have been highlighted and selected for her. To save your Daily Schedule click on the Submit button. You will be presented with the Your Daily Schedules page, shown below. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Using Reporting For Call Center 63 To leave the Daily Schedule – Skillsets page without saving any changes you might have made, click on the Cancel button. You will be returned to the Your Daily Schedules page. When you have created a Daily Schedule it will appear in the Your Daily Schedule page, as shown below. Note: If you select the Agent Audit Report, the Activity Code Report by Skillset, Agent Activity Code Report by Agent or the Activity Code Report by # of Pegs Reports to be included in your Print Schedule, you will be further prompted for the Agents and/or the Activity Codes you wish to have included within these Reports. These further steps are described on Pages 156 (Agent Audit Report), 161 (Activity Code Report by Skillset), 165 (Activity Code Report by Agents) and 169 (Activity Code report by # of Pegs). Figure 48 Your Daily Schedules with a Schedule in the List Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 64 Using Reporting for Call Center Note that each Schedule can be identified by the Schedule Name that was provided earlier when the Schedule was created. Beside each listed Schedule are two buttons. The Edit button allows you to change the settings for a Schedule. The Delete button allows you to remove the Schedule completely. Edit Clicking on the Edit button presents you with the Edit Daily Schedule page, shown below. Figure 49 Edit Daily Schedules Page Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Using Reporting For Call Center 65 This page operates exactly like the Add Daily Schedule page, except the data fields and check boxes are already populated with the settings of the Schedule you are editing. To save any changes to the Daily Schedule click on the Submit button. You will be returned to the Your Daily Schedules page. To leave the Edit Daily Schedule page without saving any changes you might have made, click on the Cancel button. You will be returned to the Your Daily Schedules page. Delete Clicking on the Delete button will remove the Schedule from the system entirely, and will remove its listing from the Your Daily Schedules page. You will be asked to confirm the deletion, and you will be returned to the Your Daily Schedules page. Weekly Schedules Selecting the Weekly Schedules option presents you with the Your Weekly Schedules page, shown below. Initially this will be empty. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 66 Using Reporting for Call Center Figure 50 Your Weekly Schedules Page Clicking on the Add button will present you with Add Weekly Schedule page, shown below. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Using Reporting For Call Center 67 Figure 51 Add Weekly Schedule Page The Add Weekly Schedule page allows you to specify the which reports you wish to have included in the Schedule, and when it is to be printed. You may also specify which period of the day the reports will contain. You must also specify a name for your Schedule and which printer you wish to have the reports generated on. To select a report to be included in the Schedule, click the check box beside the report name. Selected reports will have a tick in the check box beside their name. You can of course select multiple reports. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 68 Using Reporting for Call Center The reports will be generated for a calendar week. You must specify which day and at what time you wish to have the Weekly Schedule reports generated. Note: Weekly Schedules generate reports on the specified day at the specified time. However, the reports generated contain information from the previous calendar week. An example will make this clear. Suppose a User created a Weekly Schedule that would print on a Saturday. They create this Schedule on September 10th, 2003. On Saturday September 13th the Weekly Schedule would generate Weekly reports. These Reports would contain information relating to the week September 1st –September 7th. Reports containing the information relating to the week September 8th – September 14th would be printed on Saturday 20th September, and so on. September 2003 Mon Tue Wed Thu Fri Sat Sun 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Figure 52 Calendar for September 2003 To set a name for your Schedule, type the name in the Schedule Name field. This is to help you identify, and distinguish between, the different Schedules you create. The Report Period Start Time and Report Period End Time dictate the period within each day for which the reports are generated. For example, if your Call Center has a working day that starts at 08:30 and finishes at 17:30, you may wish to specify the Start Time as 08:00 (to see if you have early calls that you are missing by not having the Call Center open) and 18:00 (to see if there is a late surge of calls). To specify which printer the reports will be generated on, select one of the options from the Select printer drop-down menu. This drop-down menu will list all of the printers which are accessible from the Web Host PC. (The reports are generated from the databases held in the Web Host PC.) Our example User Mary Smith has configured her Weekly Schedule as shown below. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Using Reporting For Call Center 69 Figure 53 Add Weekly Schedule Page - Example Schedule Mary Smith has selected the Answered Calls, Abandoned Calls, CLID and Call Average reports to be printed at 08:30 on Mondays. Her schedule is Called WeeklyCalls. The reports will start to be generated at 08:30, on the HP 840C DeskJet printer. The reports will cover the period from midnight to midnight for each day. To save your Weekly Schedule click on the Submit button. You will be presented with the Weekly Schedules – Skillsets page, shown below. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 70 Using Reporting for Call Center Figure 54 Weekly Schedules - Skillsets The Weekly Schedule - Skillsets page allows you to select which Skillsets you wish to have included within the generated reports that are produced by the Weekly Schedule. • • For a discussion of using Skillset Selection lists see page 60. For a discussion on using Favourites, see page 61. Our example User Mary Smith has used her Dev&Train Favourite to highlight and select the Development and Training Skillsets. To save your Weekly Schedule click on the Submit button. You will be presented with the Your Weekly Schedules page, shown below. To leave the Weekly Schedule – Skillsets page without saving any changes you might have made, click on the Cancel button. You will be returned to the Your Weekly Schedules page. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Using Reporting For Call Center 71 When you have created a Weekly Schedule it will appear in the Your Weekly Schedule page, as shown below. To leave the Add Weekly Schedule page without saving any changes you might have made, click on the Cancel button. You will be prompted to confirm that you do not wish to save your changes. You will be returned to the Your Weekly Schedules page. Note: If you select the Agent Audit Report, the Activity Code Report by Skillset, Agent Activity Code Report by Agent or the Activity Code Report by # of Pegs Reports to be included in your Print Schedule, you will be further prompted for the Agents and/or the Activity Codes you wish to have included within these Reports. These further steps are described on Pages 156 (Agent Audit Report), 161 (Activity Code Report by Skillset), 165 (Activity Code Report by Agents) and 169 (Activity Code report by # of Pegs). When you have created a Weekly Schedule it will appear in the Your Weekly Schedule page, as shown below. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 72 Using Reporting for Call Center Figure 55 Your Weekly Schedule Page with a Schedule in the List Note that each Schedule can be identified by the Schedule Name that was provided earlier when the Schedule was created. Beside each listed Schedule are two buttons. The Edit button allows you to change the settings for a Schedule. The Delete button allows you to remove the Schedule completely. Edit Clicking on the Edit button presents you with the Edit Weekly Schedule page, shown below. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Using Reporting For Call Center 73 Figure 56 Edit Weekly Schedule Page This page operates exactly like the Add Weekly Schedule page, except the data fields and check boxes are already populated with the settings of the Schedule you are editing. To save any changes to the weekly Schedule click on the Submit button. You will be returned to the Your Weekly Schedules page. To leave the Edit Weekly Schedule page without saving any changes you might have made, click on the Cancel button. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 74 Using Reporting for Call Center You will be returned to the Your Weekly Schedules page. Delete Clicking on the Delete button will remove the Schedule from the system entirely, and will remove its listing from the Your Weekly Schedules page. You will be asked to confirm the deletion, and you will be returned to the Your Weekly Schedules page. Monthly Schedules Selecting the Monthly Schedules option presents you with the Your Monthly Schedules page, shown below. Initially this will be empty. Figure 57 Your Monthly Schedules Page Clicking on the Add button will present you with Add Monthly Schedule page, shown below. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Using Reporting For Call Center 75 Figure 58 Add Monthly Schedule Page The Add Monthly Schedule page allows you to specify the which reports you wish to have included in the Schedule, and when it is to be printed. You may also specify which period of the day the reports will contain. You must also specify a name for your Schedule and which printer you wish to have the reports generated on. To select a report to be included in the Schedule, click the check box beside the report name. Selected reports will have a tick in the check box beside their name. You can of course select multiple reports. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 76 Using Reporting for Call Center The reports will be generated for a calendar month. You must specify the time you wish to have the Monthly Schedule reports generated. They will be generated on the 1st day of each Month, at the specified time. To set a name for your Schedule, type the name in the Schedule Name field. This is to help you identify, and distinguish between, the different Schedules you create. The Report Period Start Time and Report Period End Time dictate the period within each day for which the reports are generated. For example, if your Call Center has a working day that starts at 08:30 and finishes at 17:30, you may wish to specify the Start Time as 08:00 (to see if you have early calls that you are missing by not having the Call Center open) and 18:00 (to see if there is a late surge of calls). To specify which printer the reports will be generated on, select one of the options from the Select printer drop-down menu. This drop-down menu will list all of the printers which are accessible from the Web Host PC. (The reports are generated from the databases held in the Web Host PC.) Our example User Mary Smith has configured her Monthly Schedule as shown below. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Using Reporting For Call Center 77 Figure 59 Add Monthly Schedule Page with Example Schedule Mary Smith has selected the Answered Calls, Abandoned Calls, CLID and Call Average reports to be printed at 08:30 (on the 1st day of each new month). Her schedule is Called MonthlyCalls. The reports will start to be generated at 08:30, on the HP 840C DeskJet network printer. The reports will cover the period from midnight to midnight for each day. To save your Monthly Schedule click on the Submit button. You will be presented with the Monthly Schedules – Skillsets page, shown below. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 78 Using Reporting for Call Center To leave the Add Monthly Schedule page without saving any changes you might have made, click on the Cancel button. You will be returned to the Your Monthly Schedules page. Figure 60 Monthly Schedule - Skillsets Page The Monthly Schedule - Skillsets page allows you to select which Skillsets you wish to have included within the generated reports that are produced by the Monthly Schedule. • • For a discussion of using Skillset Selection lists see page 60. For a discussion on using Favourites, see page 61. Our example User Mary Smith has used her Dev&Train Favourite to highlight and select the Development and Training Skillsets. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Using Reporting For Call Center 79 Note: If you select the Agent Audit Report, the Activity Code Report by Skillset, Agent Activity Code Report by Agent or the Activity Code Report by # of Pegs Reports to be included in your Print Schedule, you will be further prompted for the Agents and/or the Activity Codes you wish to have included within these Reports. These further steps are described on Pages 156 (Agent Audit Report), 161 (Activity Code Report by Skillset), 165 (Activity Code Report by Agents) and 169 (Activity Code report by # of Pegs). To save your Monthly Schedule click on the Submit button. You will be presented with the Your Monthly Schedules page, shown below. To leave the Monthly Schedule – Skillsets page without saving any changes you might have made, click on the Cancel button. You will be returned to the Your Monthly Schedules page. When you have created a Monthly Schedule it will appear in the Your Monthly Schedule page, as shown below. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 80 Using Reporting for Call Center Figure 61 Your Monthly Schedules Page with a Schedule in the List Note that each Schedule can be identified by the Schedule Name that was provided earlier when the Schedule was created. Beside each listed Schedule are two buttons. The Edit button allows you to change the settings for a Schedule. The Delete button allows you to remove the Schedule completely. Edit Clicking on the Edit button presents you with the Edit monthly Schedule page, shown below. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Using Reporting For Call Center 81 Figure 62 Edit Monthly Schedule Page This page operates exactly like the Add Monthly Schedule page, except the data fields and check boxes are already populated with the settings of the Schedule you are editing. To save any changes to the Monthly Schedule click on the Submit button. You will be returned to the Your Monthly Schedules page. To leave the Edit Monthly Schedule page without saving any changes you might have made, click on the Cancel button. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 82 Using Reporting for Call Center You will be returned to the Your Monthly Schedules page. Delete Clicking on the Delete button will remove the Schedule from the system entirely, and will remove its listing from the Your Monthly Schedules page. You will be asked to confirm the deletion, and you will be returned to the Your Monthly Schedules page. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Using Reporting For Call Center 83 Real Time Using the Real Time Options Selecting the Real Time option presents you with the Real Time Menu page. The Real Time Menu page is shown below, with the real Time options displayed in the list on the left-hand side of the page. Figure 63 Real Time Menu Page Selecting the Real Time Summary option presents you with the Real Time Summary page, shown below. Real Time Summary This page allows you to specify which Skillsets you wish to include within the Real Time display. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 84 Using Reporting for Call Center Figure 64 Real Time Summary Skillset Selection Page • • For a discussion of using Skillset Selection lists see page 60. For a discussion on using Favourites, see page 61. Our example User Mary Smith has used her Dev&Train Favourite to highlight and select the Development and Training Skillsets. Clicking on the Call Summary button presents you with the Summary Real Time page, shown below. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Using Reporting For Call Center 85 Figure 65 Real Time Summary Real Time Screens The display shows the Agent Summary and the Call Summary Real Time panels. The information represented in these will update as Agent and Call activity changes in your Call Center. Each row in each table represents a single Skillset. The Skillsets contained within the tables are those previously chosen on the Real Time Summary Skillset Selection Page (see Page 84). Real Time Summary - Agent Summary This Real Time panel indicates the numbers and states (current activities) of the logged in Agents, for each of the selected Skillsets. Note that the state of an Agent who has multiple calls on their handset is taken from their active call. For example, if an Agent has an Incoming Call Center Call on hold and they are active on an Outgoing Call then the Agent is shown to be in the Outgoing Call state. Skillset This indicates which Skillset the information in this row represents. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 86 Using Reporting for Call Center Logged In Indicates the number of Agents who are logged into this Skillset. Supervising Indicates the number of Agents (Supervisors) who are currently supervising other Agents. Available Indicates the number of Agents who are Available to take Incoming Call Center Calls. Not Ready Indicates the number of Agents who are in the Not Ready State. They may have invoked the Make Not Ready feature or they might have been placed in the Not ready state because a Call Center Call was presented ringing to their handset but the Agent did not answer it, and Nortel Networks Reporting for Call Center automatically took the call back to the Skillset queue and made them Not Ready. On Call Center Calls Indicates the number of Agents who are currently handling Incoming Call Center Calls. Break Time Indicates the number of Agents who are in Break Time following clear down of an Incoming Call Center Call. On Non-Call Center Calls Indicates the number of Agents who are currently handling calls that have not arrived via the Call Center. These could be calls that have arrived directly at their handset because somebody has rung their DDI line, for example, or a non-Call Center Call has been transferred to them from another handset. On Outgoing Calls Indicates the number of Agents who are currently on Outgoing Calls. On Internal Calls Indicates the number of Agents who have placed or answered internal (intercom) calls. With All Calls Held Indicates the number of Agents who have all of their current calls on hold. Real Time Summary – Call Summary This Real Time panel provides information about calls that are in the Skillset queues waiting to be answered, together with some statistics regarding calls which have been completed. These statistics will update in real time. This information is shown for each of the selected Skillsets. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Using Reporting For Call Center 87 Waiting Indicates the number of calls that are currently waiting in the Skillset queues to be answered. Primary Alert Indicates the number of currently waiting Calls that have waited in excess of the Call Center Primary Alert. (note that this is mutually exclusive with the Secondary Alert). If any calls have waited in excess of the Primary Alert the background to this cell will change to yellow. Secondary Alert Indicates the number of currently waiting Calls that have waited in excess of the Call Center Secondary Alert. (note that this is mutually exclusive with the Primary Alert). If any calls have waited in excess of the Secondary Alert the background to this cell will change to red. Overflow Indicates the number of currently waiting Calls that have waited in excess of the Call Center Overflow Threshold. Note that this does not mean the call has overflowed, but the Call Center is actively looking through the overflow rules that have been defined for this Skillset, in order to try to find a means of answering the call. That is, this call is liable to overflow shortly. If any calls have waited in excess of the Overflow Threshold the background to this cell will change to red. Note that if a call had passed the overflow threshold in one Skillset and was then Moved to another Skillset due to the call routing that had been configured, the call will appear in the new Skillset and the cell background will be red as this call has already passed the overflow threshold of the original Skillset it was in. Abandoned Hour / Day Indicates the number of calls that have abandoned in the Skillsets, in the current hour and in the current day. Answered Hour / Day Indicates the number of calls that have been answered by the Agents in the Skillsets, in the current hour and in the current day. Longest Waiting Time Indicates the waiting time of the call that has waited the longest out of the list of currently waiting calls. Unread Skillset Messages Indicates the number of voice mail messages in the Skillset Mailbox which have not be listened to. If there are any messages which have not been listened to the cell background will be red. GOS Indicates the grade of service currently being offered to incoming callers. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 88 Using Reporting for Call Center Skillset Mode Indicates whether the mode of operation of the Skillset. Hiding the Real Time Panels Hide Agent Summary Above the Agent Summary panel is a link ‘Hide Agent Summary’. Clicking this removes the Agent Summary Panel and leaves the Call Summary Panel on view. The link will change to ‘Show Agent Summary’. Clicking on this link will restore the Agent Summary Panel to the Real Time screen. Hide Skillset Call Summary Above the Call Summary panel is a link ‘Hide Call Summary’. Clicking this removes the Call Summary Panel and leaves the Agent Summary Panel on view. The link will change to ‘Show Call Summary’. Clicking on this link will restore the Call Summary Panel to the Real Time screen. Real Time Detail This page allows you to specify which Skillsets you wish to include within the Real Time display. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Using Reporting For Call Center 89 Figure 66 Real Time Detail Skillset Selection Page Call Detail The Call Detail Real Time screen presents a detailed display of the status of waiting calls together with some statistics relating to completed calls. These statistics will update in real time. The Call Detail Real Time screen displays a separate line of information for Multimedia Calls and for Voice (PSTN) Calls, and a total for both types of calls. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 90 Using Reporting for Call Center Figure 67 Real Time Call Detail Page Media Type Indicates whether the line of statistics relates to Multimedia Call or Voice (PSTN) Calls, or a total for both types of call. Waiting Indicates the number of calls that are currently waiting in the Skillset queues to be answered. Primary Alert Indicates the number of currently waiting Calls that have waited in excess of the Call Center Primary Alert. (note that this is mutually exclusive with the Secondary Alert). If any calls have waited in excess of the Primary Alert the background to this cell will change to yellow. Secondary Alert Indicates the number of currently waiting Calls that have waited in excess of the Call Center Secondary Alert. (note that this is mutually exclusive with the Primary Alert). If any calls have waited in excess of the Secondary Alert the background to this cell will change to red. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Using Reporting For Call Center 91 Overflow Indicates the number of currently waiting Calls that have waited in excess of the Call Center Overflow Threshold. Note that this does not mean the call has overflowed, but the Call Center is actively looking through the overflow rules that have been defined for this Skillset, in order to try to find a means of answering the call. That is, this call is liable to overflow shortly. If any calls have waited in excess of the Overflow Threshold the background to this cell will change to red. Note that if a call had passed the overflow threshold in one Skillset and was then Moved to another Skillset due to the call routing that had been configured, the call will appear in the new Skillset and the cell background will be red as this call has already passed the overflow threshold of the original Skillset it was in. Abandoned Hour / Day Indicates the number of calls that have abandoned in the Skillsets, in the current hour and in the current day. Answered Hour / Day Indicates the number of calls that have been answered by the Agents in the Skillsets, in the current hour and in the current day. On Hold Indicates how many calls are placed on hold. Longest Waiting Time Indicates the waiting time of the call that has waited the longest out of the list of currently waiting calls. Unread Skillset Mailbox Msgs Indicates the number of voice mail messages in the Skillset Mailbox which have not be listened to. If there are any messages which have not been listened to the cell background will be red. GOS Indicates the Grade of Service being offered to incoming callers. Agent Detail The Agent Detail Real Time screen presents a detailed display of the individual status of the logged in Agents, together with some statistics relating to calls answered and made by the Agents. These statistics will update in real time. Each line of the Agent Detail Real Time screen represents a single Agent. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 92 Using Reporting for Call Center Figure 68 Agent Detail Real Time Page ID Indicates the Call Center ID of the Agent. Agent Indicates the name of the Agent, and also indicates the state the Agent is in by colouring the cell background. The state of the Agent is dependant on their current activity. Further detail on the Agent state can be seen in the Status column. Incoming An Agent is in the Incoming State when they have answered an Incoming Call Center Call. The information in the Status column indicates the type of call. The Incoming State is represented by Light Green. Break Time Break Time is the term used to describe the period of time allocated to each Agent to allow post call completion work, also called wrap-up. Break Time is represented by Dark Green. Outgoing Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Using Reporting For Call Center 93 When an Agent makes an Outgoing Call they are said to be in the Outgoing State. The Outgoing State is represented by Yellow. Supervisory Monitoring When an Agent who has been created in the Call Center as a Supervisor undertakes a monitoring session with another Agent they are represented in the Real Time screen using Gold. The Status column will display ‘Monitoring’. Non-Call Call Center Call If the Agent answers a non-Call Center Call they are represented using Grey. Available Blue is used to represent Available Agents. These are Agents who are available to answer Incoming Call Center Calls. All Calls Held Magenta is used to indicate an Agent who has placed all of their calls on hold. Not Ready Dark Grey is used to represent Agents who are in the Not Ready state. Logged Into SS Indicates the Skillsets the Agent is currently logged in to. Status This column is used to provide extra detail regarding the Agent state. A phone icon with the wording Multimedia represents a Multimedia voice call. A phone icon with the wording Voice represents a regular voice call. A phone icon with the wording Outgoing represents an outgoing call. A phone icon with the wording Intercom represents an internal call. The word Available represents an Available Agent. The wording BreakTime represents an Agent in Break Time. The wording Calls Held represents an Agent with all of their current calls on hold. The wording Not Ready represents an Agent who is in the Not Ready state. The word Monitoring represents an Agent who is a Supervisor engaged in a Supervisory Monitoring session with another Agent, or in a Help Session. A smiley icon represents a Multimedia Chat session. A globe icon represents a Multimedia Follow-me browsing session. A number will accompany the status description in the form of SSx. This indicates the Skillset associated with the call. For example, SS2 would indicate Skillset 2. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 94 Using Reporting for Call Center Duration This column displays a timer which represents the time the Agent has spent in the current state. If the Agent has been in the current state for a period in excess of the associated Agent Alarm, the background of this cell will turn red. See the section Agent Alarms, below. Answered Call Center Calls Hour / Day Indicates the number of Call Center Calls that this Agent has answered in the current hour and in the current day. Outgoing Calls Hour / Day Indicates the number of Outgoing Calls that this Agent has made in the current hour and in the current day. Answered Non-Call Center Calls Hour / Day Indicates the number of Non-Call Center Calls that this Agent has answered in the current hour and in the current day. Agent Alarms The Agent Alarms option allows you to set Real Time thresholds which operate with reference to the Call Center activity of the Agents. For example, you can specify average durations of Incoming or Outgoing calls, and Nortel Networks Reporting for Call Center will highlight Agents who have been on a call longer than the specified threshold. Selecting the Agent Alarms option presents you with the Agent Alarms Page (shown below), and the Agent Alarm menu option appears in the menu list on the left-hand side of the page. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Using Reporting For Call Center 95 Figure 69 Agent Alarm Menu Page Selecting the Agent Alarm Setup option presents you with the Agent Alarm Setup Skillset selection page shown below. This page allows the User to select from their assigned Skillsets which Skillsets they wish to establish the Agent Alarms settings for. In our example shown below, the Favourites list is showing the Favourite that was created previously by the User Mary Smith. She has clicked on the Select button and Nortel Networks Reporting for Call Center has automatically highlighted and selected the two Skillset Development and Training. • • For a discussion of using Skillset Selection lists see page 60. For a discussion on using Favourites, see page 61. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 96 Using Reporting for Call Center Figure 70 Agent Alarms Setup Page When you have selected your Skillset, clicking on the Assign values button will present you with the Agent Alarms Values page, shown below. You may specify Agent Alarm settings for the following Agent activities (also called Agent states): Available Internal Call Outgoing Call Incoming Call Center Call Incoming Multimedia Call Incoming Chat Incoming Non-Call Center Not Ready Agent is free to take a call Agent is on an intercom call Agent has placed a call to an external party Agent has answered a Call Center Call Agent has answered a Multimedia Call Center Call Agent is on a Multimedia Call Center Chat session Agent has answered a non-Call Center Call from an external party The Agent is in the Not Ready state Out example User Mary Smith has specified various values, as can be seen below. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Using Reporting For Call Center 97 Figure 71 Agent Alarms Values Page To save the Agent Alarms Values settings you have made, click the Submit button. You will be returned to the Agent Alarms Setup page, To leave the Agent Alarms Values page without saving any changes you might have made, click the Cancel button. You will be returned to the Agent Alarm Setup page. Wallboard Setup Introduction If you have been allocated the rights to the Wallboard Setup option by your Administrator (see the description of the Add User page on Page 34), you will be able to use this option to assign wallboards to your assigned Skillsets, You will also be able to configure the wallboards with features such as wallboard alarms and messages, schedules and summaries. If you have not been awarded the rights to assign wallboards by your Administrator, the Wallboard Setup option will be greyed out. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 98 Using Reporting for Call Center Nortel Networks Reporting for Call Center can drive both hardware and software IP-enabled wallboards. The wallboards which are supported are the ipView Wallboards (hardware tricolour wallboards) and the ipView SoftBoard (software based personal wallboard). They are updated approximately every 3 seconds. Message Formats The information sent to the wallboards is in one of three different formats. Parameter Messages Parameter Messages are the ‘regular’ display message sent to the wallboard. Parameter Messages show 6 statistical parameters, each of which is displayed alongside a two letter mnemonic abbreviation. (If the wallboard is configured to have a title then the number of parameters that can be displayed is dropped to 3.) The parameters available for display on the wallboards are: ID IH AD AH OD OH SD SH AO AI AA AN AL QL QT Number of Incoming calls received in the current Day Number of Incoming calls received in the current Hour Number of Abandoned calls in the current Day Number of Abandoned calls in the current Hour Number of Outgoing calls made in the current Day Number of Outgoing calls made in the current Hour Grade of Service offered in the current Day (%) Grade of Service offered in the current Hour (%) Number of Agents on Outgoing calls Number of Agents on Incoming calls Number of Agents Available to receive calls Number of Agents in the Not Ready state Number of Agents Logged in Current Queue Length - number of calls queuing for this Skillset Current Queue Time for the longest waiting Call for this Skillset (secs.) The numerical values are displayed in yellow and the abbreviations are displayed in green. If one of the parameter values has an associated Alarm threshold configured for it, it will display in red when the threshold is broached. There is an optional audible alert for alarms. Scrolling Messages Scrolling Messages (also known as rolling messages) are supported by the wallboards also. These are either manually dispatched messages, Alarm messages or Scheduled messages. These are described below. Scrolling messages move from right to left across the wallboard until the whole message has been displayed at least two times. There is also an optional audible alert for scrolling messages. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Using Reporting For Call Center 99 Note: On the ipView SoftBoards, the scrolling messages do not ‘scroll’, they are displayed in their entirety in a window, for the duration that it would take for that message to scroll at least two times on the hardware wallboard. Also note that the numerical parameter display is removed from ipView SoftBoards for the duration of the message display. Scrolling message are displayed on the wallboards under three circumstances. Scrolling messages can be triggered because: • A Call Center statistic has entered an Alarm state (generating an Alarm message) • A predefined time has arrived (generating a scheduled message) • A User has generated and dispatched a message (Instant (manual) message). Nortel Networks Reporting for Call Center can be configured to provide an audible alert for any of these scrolling messages. A scrolling message can be up to 64 characters in length and can contain parameter values which are automatically replaced by the numerical equivalent at display time. For example, if a message contained the text: There are (QL) calls waiting… And the Call Center statistic QL currently had a value of 4, the following message would be displayed: There are 4 calls waiting… Alarm Messages Nortel Networks Reporting for Call Center can be configured to automatically provide a scrolling test message when a parameter enters an Alarm condition, by passing a defined Alarm Threshold. A profile of 6 different Alarm Thresholds can be set across a day, for a single Alarm. For example, a 24-hour Call Center which has 25 Agents active during the day might have an Alarm Message set to be triggered if 6 Agents are Not Ready concurrently, but at Night they have a skeleton staff of 4 Agents and so they want to have the same Alarm Message triggered when only 2 Agents make themselves Not ready. Alarm messages scroll at least twice on the wallboards. If the alarm is still valid when the message has scrolled at least twice, the normal numerical display will be shown for 5 seconds before the alarm message is re-scrolled. If several alarms are triggered at once they will be scrolled to the wallboard as follows. Assume three alarms are triggered concurrently. The first alarm message is scrolled at least twice, then the normal numerical display is shown for 5 seconds. The second alarm message is then scrolled at least twice and the normal numerical display is shown again, for 5 seconds. If the third alarm is still valid then the third alarm message is scrolled at least twice and the display then returns to the usual numerical display for 5 seconds. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 100 Using Reporting for Call Center If the first alarm is valid it is scrolled again. If it is not valid then the second alarm is checked to see whether it is valid. If the second alarm is valid it is scrolled again. If it is not valid then the third alarm is checked to see whether it is valid. In this way all alarms are rotated and displayed with a numerical display of 5 seconds in between them. Instant Messages System Administrators or Users can manually enter and dispatch an Instant Message to the wallboards. Instant messages will take priority over Alarm messages. Scheduled Messages Wallboard Messages which need to go out at the same time every day, or on a particular day can be associated with a schedule. For example, weekly fire alarm tests or a start of shift greeting or an end of shift message could be configured so that it automatically triggers at the specified time. Schedules can be configured to trigger on single days, groups of days or every day. Scheduled messages will take priority over Alarm messages. Summary Messages Nortel Networks Reporting for Call Center can be configured to provide pre-defined hourly summaries on the wallboards. Summaries can be configured to have an audible alert. The values displayed in the summary messages are as follows: Incoming Calls for previous Hour and Day so far Outgoing Calls for previous Hour and Day so far Answered Calls for previous Hour and Day so far Grade of Service for previous Hour and Day so far Using the Wallboard Options Selecting the Wallboard Setup option presents you with the Wallboard Menu page shown below, with the wallboard options displayed in the list on the left-hand side of the page. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Using Reporting For Call Center 101 Figure 72 Wallboard Menu Page Selecting the Wallboard Assignment option presents you with the Wallboard Assignment page, shown below. Wallboard Assignment Page This page display a list of the configured wallboards. It displays them for each of the Skillsets you have been assigned, and any which have been configured as System wallboards. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 102 Using Reporting for Call Center Figure 73 Wallboard Assignment Page The Wallboard Setup page will display a list of the assigned wallboards. You are able to delete wallboards or to edit their settings. In this example there are no wallboards assigned to the selected Skillsets (in this example System wallboards and wallboards for Skillsets 3, 7 and 9), so all our example User Mary Smith can do is Add wallboards. Click on the Add button to assign wallboards. This will present you with the Add Wallboard page, shown below. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Using Reporting For Call Center 103 Figure 74 Add Wallboard Page Add Wallboard Page The details of the new wallboard that must be specified are as follows: IP Address or the Network Name. (If the wallboard is an ipView SoftBoard the details to add are the IP Address or the Network Name of the PC on which the SoftBoard will be running.) Port. This is usually left at the default value of 3500. This might be changed for an ipView SoftBoard if an Agent wished to have several copies of ipView SoftBoard running on the same PC. This could be done to display different Skillset statistics to a multi-Skillset Agent for example. Each copy of ipView SoftBoard would be installed on the Agent’s PC with a different Port number. In that case, the corresponding wallboard entry in Nortel Networks Reporting for Call Center must be configured with the appropriate port number. Wallboard Skillset. This denotes the Skillset the wallboard is to report on. That is, the named Skillset is the Skillset from which Nortel Networks Reporting for Call Center will extract the statistical information to display on the wallboard. If you wish to display system wide totals (that is, to have the information displayed represent totals derived from all Skillsets) then select ‘System’ from the drop down menu. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 104 Using Reporting for Call Center In other words, assigning a wallboard to be a System wallboard causes Nortel Networks Reporting for Call Center to send statistics to that wallboard which represent the system totals. For example, the parameter AN (agents not ready) on a System wallboard shows the total figure for the AN values of all Skillsets added together. Notice that the only Skillsets available in this drop-down menu are the ones that our example User Mary Smith has had assigned to her by the Administrator. Language. This drop-down menu allows the User to specify which language the wallboard should be driven in. Individual wallboards can be driven in any of the supported languages, selected from the list. Type. This indicates whether the wallboard is a hardware wallboard or a software SoftBoard. Any of the available parameters can be used on either the hardware or the software wallboards. The parameter spacing on the hardware wallboard allows for the display of two 3 digit and one 4 digit parameter per line, giving 6 parameters in total. The two parameters at the right hand end of the wallboard are able to display up to 4 digits at a time. Those parameters that are able to reach 4 digits can not be configured for the positions which can only display 3 digits. See Wallboard Parameters, below. Title. This checkbox indicates whether the wallboard is to be configured with a title. A title is a string of text up to 16 characters in length which is displayed on the top line of a hardware wallboard, and above the parameter list on a SoftBoard. In both cases it reduces the number of parameters which can be displayed by the wallboard to 3. Title Text. If the Title check box is selected thus field is editable, to allow you to define the text to be displayed as the title. Buzzer. If this check box is selected the wallboard will emit a short bleep whenever a Summary Message or a Scrolling message is sent to it. It will also bleep when a parameter goes into alarm even if there is no Alarm Message associated with the alarm (a static alarm). Summary. If this check box is selected Hourly Summaries will be sent to the wallboard when each hour passes, and whenever the Skillset enter Out Mode (that is, there are no Agents Logged In to the Skillset). To save the changes you have made click the Submit button. You will be returned to the Wallboard Setup page. To leave the Add Wallboard page without saving any changes you might have made, click on the Cancel button. You will be returned to the Wallboard Setup page. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Using Reporting For Call Center 105 Wallboard Parameters Once you have assigned a wallboard, they will be listed on the Wallboard Setup Page. This is shown below. Figure 75 Wallboard Setup Page with Wallboard Listed Beside the wallboard entries are buttons that will allow you to edit the settings for the wallboard (by using the Edit Button) and to specify the parameters you wish to have displayed on the wallboard (by using the Parameter button) and to remove the wallboard from the list entirely (by using the delete button). Edit Button Clicking on the Edit button presents you with the Edit Wallboard page, shown below. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 106 Using Reporting for Call Center Figure 76 Edit wallboard Page The Edit Wallboard page operates exactly like the Add Wallboard page, except the data fields are already populated with the values of the wallboard you have selected to edit. To save the changes you have made click the Submit button. You will be returned to the Wallboard Setup page. To leave the Add Wallboard page without saving any changes you might have made, click on the Cancel button. You will be returned to the Wallboard Setup page. Parameters Button Clicking on the Parameters button presents you with the Edit Parameters page, shown below. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Using Reporting For Call Center 107 Figure 77 Edit Parameters Page The Edit Parameters page allows you to specify which 6 (or three, if you have specified that the wallboard is going to have a title, see Page 104) parameters are going to be displayed on the wallboard. The list of available parameters is shown on Page 98. You select the parameters from the drop down menus. Note: If the wallboard you are specifying parameters for is a hardware wallboard, some parameters only appear in positions 3 and 6. The drop-down menus for positions 1, 2, 4 and 5 will not feature those parameters. This is because those parameters that are restricted to positions 3 and 6 are capable of displaying up to 4 digits. Positions 3 and 6 on the hardware wallboard are larger than positions 1, 2, 4 and 5. Any parameter can occupy any position on a software wallboard. When you have selected your parameters, click on the Submit button. You will be returned to the Wallboard Setup page. To return to the Wallboard Setup page without saving any changes you might have made, click the Cancel button. You will be asked to confirm that you do not wish to save your changes. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 108 Using Reporting for Call Center Delete Button Clicking on the Delete button will remove the wallboard definition from the system entirely, and will remove its listing from the Wallboard Setup page. You will be asked to confirm the deletion, and you will be returned to the Wallboard Setup page. Wallboard Messages Page The Messages option allows you to create and store messages which can be used as Alarm or Scheduled messages. Selecting the Messages option presents you with the Assigned Messages page, shown below. This page will list all of the messages which have been configured. Any message can be used by any Skillset. Initially the list of Assigned Messages will be empty (as shown). Figure 78 Assigned Messages Page Clicking on the Add button will present you with the Add Messages page shown below. You may type your message text into the field. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Using Reporting For Call Center 109 Note that if you include a parameter abbreviation in round brackets ‘(‘ and ‘)’ in the text of the message, that parameter abbreviation will be replaced by the appropriate numerical value of that Call Center statistic when the message is displayed. See the list of available parameters on Page 98, and the discussion of parameter abbreviations being replaced with numerical values on Page 99. Figure 79 Add Message Page Our example User Mary Smith has entered the following message in the Add Message text field, shown below: There are (AN) Agents Not Ready please return to available The parameter abbreviation AN represents Agents Not Ready. When this message is displayed on the wallboards the current numerical value of AN will be inserted into the message instead of the (AN) symbol. If there were 6 Agents Not Ready at the time the message was displayed on the wallboard the following text would be displayed: Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 110 Using Reporting for Call Center There are 6 Agents Not Ready please return to available Figure 80 Add Message Page - Example Text When you have entered the message text you wish to use, click on the Submit button to save it. You will be returned to the Assigned Messages page, shown below. To leave the Add Messages page without saving any changes you might have made, click the Cancel button. You will then be returned to the Assigned Messages page, shown below. Our example User Mary Smith clicked on Submit to save her new message. Her Assigned Messages List would now include the message she saved. This is shown below. Mary Smith has also entered a message which will be used in a schedule. This message does not include any parameter abbreviations, it is purely a text message. This will be use later in a Schedule. The text of the other message is: Morning Shift Log out, Afternoon shift Log In Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Using Reporting For Call Center 111 Figure 81 Assigned Messages List - Example Messages Now that messages have been assigned to these Skillsets, they can be used in Alarms or Schedules. You can use the Edit button to amend the details of a Message, and you can use the Delete button to remove a message from the list altogether. Alarms Selecting the Alarm option presents you with the Assigned Alarms page, shown below. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 112 Using Reporting for Call Center Figure 82 Assigned Alarms Page The Assigned Alarms list will be empty initially. To create an Alarm, click on the Add button. You will be presented with the Add Alarm page, shown below. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Using Reporting For Call Center 113 Figure 83 Add Alarm Page When you assign an Alarm it is specific to a particular Skillset (or the System, if you select the System list item). An Alarm Message may be used by many Skillsets, but an Alarm is specific to a single Skillset. The alarm parameter has to be monitored in the Skillset of interest in order to allow Nortel Networks Reporting for Call Center to decide whether the alarm trigger condition has been met. Note: You may specify the same alarm conditions for different Skillsets, and these different alarms may use the same Alarm message, but they are in fact all separate and distinct alarms, and they have to be created separately. Note: If you configure an Alarm to be a System Alarm that Alarm will be displayed on all wallboards which have been configured as System wallboards. You may specify the same alarm conditions for different Skillsets, and these different alarms may use the same Alarm message, Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 114 Using Reporting for Call Center but they are in fact all separate and distinct alarms, and operate independently from one another, with no interaction what so ever. This page allows you to specify the parameter which the alarm is to be triggered by (see the list of available parameters on Page 98). The alarm message will be sent to the wallboards when the alarm has been triggered. You specify the conditions which will trigger the Alarm by providing a threshold against which the parameter value is compared. You must also specify the type of comparison that Nortel Networks Reporting for Call Center makes when deciding whether the alarm has been triggered or not. The threshold is specified as a figure. Nortel Networks Reporting for Call Center automatically understands whether the figure you supply represents: • • • • Agents (for parameters such as AN and AO) Calls (for parameters such as ID and OD) Seconds (for parameters such as QT) Percentages (for parameters such as SD) The Comparison is specified by selecting from a drop down menu one of the following: <= Less than or equals to. This type of comparison is used when you wish to monitor a parameter against some lower limit. That is, you wish to be informed if the parameter value ever drops to or decreases below the Threshold you supply. For example if you wish an alarm to be triggered if the Grade of Service for the Current Hour (SH) falls below 50, you would use SH <= 50. = Equals. This type of comparison is used when you wish to monitor a parameter against an exact figure. That is, you wish to be informed if the parameter value ever exactly matches a figure, perhaps a target. Note that in this type of comparison, if the parameter value is higher than the threshold the alarm condition is not triggered. The parameter must exactly match the threshold in order to trigger the alarm. For example, you may wish to have a congratulatory message be sent to the wallboards if you exceed your highest number of incoming calls for the day. If your highest number of incoming calls for the day was 1200, you could set an Alarm for the parameter ID. However, if you use >= the Alarm would be triggered for each and every call from 1200 onwards. Instead, you would use the format ID = 1201. This means that the alarm message will be sent only when the number of incoming calls in the day equals 1201 (one higher than your previous highest total). This avoids the message being repeatedly sent as calls continue to come in and the ID figure rise. (At the end of that day you would then take a note of your n highest ID figure, and Edit the Alarm to reflect your new record Incoming Calls in the Day total.) Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Using Reporting For Call Center 115 >= Greater than or equals to. This type of comparison is used when you wish to monitor a parameter against some upper limit. That is, you wish to be informed if the parameter value ever meets the Threshold you supply. For example, if you wish an alarm to be triggered if the number of Agents who have made themselves Not Ready rises above 4, you would use AN >= 4. To finalise the specifications for the Alarm, you must indicate which message you wish to have sent when the alarm is triggered. The available messages are displayed in a drop down menu. Note: There is also a type of Alarm that does not have an alarm message. This is known as a Static Alarm. In the case of a Static Alarm the parameter value is displayed in flashing red on the wallboard. For this type of Alarm to be effective the parameter must be one of the parameters you have chosen to have displayed on your wallboard (see the section ‘Parameters Button’ on Page 106). To specify a Static Alarm, select the No Message option from the Message drop-down menu. Alarm Periods It is possible to specify different Alarm conditions for a single Alarm for up to 6 Alarm Periods throughout a single day. The Alarm Periods are defined by specifying start times for each period. Alarm Periods allow you to specify different Thresholds, Comparisons and Messages for different periods of the day, for a single Alarm. An Alarm period will be in operation once its start time has passed and before the start time of the next period has been reached. Note: If there is only one Alarm Period configured then it will be in operation 24 hours a day. Our example User Mary Smith has configured the following Alarm with three time periods for one of her Skillsets. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 116 Using Reporting for Call Center Figure 84 Example Settings for a Multi Alarm Period Alarm The Alarm that is triggered when the parameter AN (number of Agents Not ready) passes beyond the thresholds. The Skillset in question operate three shifts of Agents. A Morning Shift, which is supplemented by additional Agents in the afternoon forming the Afternoon Shift, and Night Shift which is manned by a skeleton staff of Agents who man the Call Center throughout the night. Because the Skillset has a different number of Agents Logged in during the Morning Shift, the Evening Shift and the Late Shift, an Alarm based on Agents Not ready needs to have different thresholds to cater for the different numbers of Agents Logged in at the various periods throughout the 24 hour cycle. Alarm Period One Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Using Reporting For Call Center 117 The first Alarm Period commences at 08:30 in the morning, The comparison is >= so the Alarm will be triggered when the AN parameter meets or exceeds the threshold. The threshold is 5. This means that whenever the AN parameter reaches 5 or above the selected message is sent to the wallboards which have been assigned to this Skillset. Alarm Period Two The second Alarm Period commences at 17:30 in the evening. The comparison is >= so the Alarm will be triggered when the AN parameter meets or exceeds the threshold. The threshold is 3. This means that whenever the AN parameter reaches 3 or above the selected message is sent to the wallboards which have been assigned to this Skillset. Because there are fewer Agents in the Afternoon Shift the threshold has been lowered to 3. Alarm Period Three The third Alarm Period commences at 22:30. Note that this Alarm Period will operate until the next Alarm Period starts, which in this example will be Alarm Period One, at 08:30 the following morning. As there is only a skeleton staff on in Mary Smith’s Skillset during the Night Shift, the Threshold has been lowered to 2. In all cases the same Alarm Message is used. Because the (AN) symbol will be replaced by the appropriate value of the AN parameter when the message is displayed (which is when the Alarm is triggered) a single message can be flexible enough to be used in differing situations. However, if Mary Smith had wanted to she could have used a different message for each Alarm Period, or she could have configured any of the Alarm Periods to use a Static Alarm. Schedules Schedules allow you to automatically send a message to the wallboards of a Skillset (or the System) at a pre-defined time on a specified day or range of days. Selecting the Schedule option presents you with the Assigned Schedules page, shown below. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 118 Using Reporting for Call Center Figure 85 Assigned Schedules Page The Assigned Schedules page will display a list of the assigned Schedules. Initially this list will be empty. Click the Add button to create a new Schedule. Clicking the Add button presents you with the Add Schedule page, shown below. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Using Reporting For Call Center 119 Figure 86 Add Schedule Page The Add Schedule page allows you to configure the Schedule. When you assign a Schedule it is specific to a particular Skillset (or the System, if you select the System list item). A Schedule Message may be used by many Skillsets, but a Schedule is specific to a single Skillset. Select the Skillset you wish to assign the Schedule to from the Wallboard Skillset drop down menu. Note: If you configure a Schedule to be a System Schedule that Schedule will be displayed on all wallboards which have been configured as System wallboards. Note: You may specify the same Schedule settings for different Skillsets, and these different Schedules may use the same Schedule message, but they are in fact all separate and distinct Schedules, and they have to be created separately. You may set a Schedule to operate on a specific week-day, every day from Monday to Friday, every day from Monday to Saturday, or Daily (every day). Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 120 Using Reporting for Call Center Our example User Mary Smith has created a schedule which will operate on each day of the working week, Monday to Friday. The time the Schedule is to be triggered is specified using the 24 hour clock, and the time is set by selecting hours and minutes from the drop down menus. The message which is to be sent at the specified time on the specified range of days is selected from the drop down message menu which lists the messages which have been assigned to this Skillset. Mary Smith wants the message: Morning Shift Log Out, Afternoon Shift Log In to be sent to the Skillset 3 wallboards at 13:00, each day of her working week, which runs from Monday to Friday. When you have configured the Schedule, click on the Submit button to save it. You will be returned to the Assigned Schedules page, shown below. To leave the Add Schedules page without saving any changes you might have made, click the Cancel button. You will then be returned to the Assigned Schedules page, shown below. Figure 87 Assigned Schedules Page with Schedule Added Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Using Reporting For Call Center 121 The Assigned Schedules page is shown above with the newly created Schedule displayed. To change any of the details of a Schedule, use the Edit button. Clicking on the Edit button presents you with the Edit Schedule page, shown below. This page operates exactly like the Add Schedule page, except the data entry fields are already populated with the current settings of the Schedule when the page appears. Figure 88 Edit Schedule Page When you have edited the Schedule, click on the Submit button to save it. You will be returned to the Assigned Schedules page. To leave the Edit Schedules page without saving any edits you might have made, click the Cancel button. You will then be returned to the Assigned Schedules page. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 122 Using Reporting for Call Center Instant Messages Instant messages allow Users to manually select any one of the stored wallboard messages and to dispatch it to the wallboards at will. Users may also type in any text hand have it sent to the wallboards, for one-off requirements. These messages are dispatched to the wallboards and then discarded, they are not saved. If you wish to save a message, use the Wallboard Message options on Page 108 to add the message to the list of stored messages. Selecting the Instant Messages option presents you with the Instant Messages page, shown below. Figure 89 Instant Messages Page The Instant Messages page allows you to select the Skillsets you wish to dispatch the instant message to, from the list of Skillsets which have been assigned to you by your Administrator. • • For a discussion of using Skillset Selection lists see page 60. For a discussion on using Favourites, see page 61. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Using Reporting For Call Center 123 Our example User Mary Smith has used her Dev&Train Favourite to highlight and select the Development and Training Skillsets. Clicking the Instant Messages button presents you with the Instant messages page, shown below. Figure 90 Composing an Instant Message The Instant Messages page allows the User to select any of the stored messages from the Existing messages drop-down menu. They may also type any ad hoc message in the New message field. To send the message to the wallboards, click the Send button. • • If there is no text in the New message field, the displayed message in the Existing messages drop down will be sent to the wallboards. If there is text in the New message field that text is sent to the wallboards. In both cases you will be returned to the Instant Messages page. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 124 Using Reporting for Call Center To return to the Instant Messages page without sending an Instant Message, click on the Cancel button. Note: As usual, you can include parameter abbreviations in brackets in the text of the New message to have Nortel Networks Reporting for Call Center automatically replace these with the correct numerical value for the parameter when the message is displayed. (See the section on Page 99 which describes parameter substitution.) Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Reports 125 Reports 6 Reports Introduction General Nortel Networks Reporting for Call Center provides you with a flexible and easy to understand set of reports. The reports contain information on the call traffic in and out of your Call Center, and on the activities of your Call Center Agents. Report Periods Reports can be generated for any elapsed period of time. This means that if you want to have a report that contains information from 12:00 mid-day Tuesday to 16:15 Thursday afternoon, you can easily obtain it. There are no pre-defined limitations on the period of time a report can include. Skillset Selection Many reports allow the User to choose to report on any combination of the Skillsets they have been assigned. They can report on a single Skillset, a combination of their assigned Skillsets or all of their assigned Skillsets. But note that some reports might not operate in the way initially expected. For example, if you request an Agent Profile report for Skillset 1, you will receive a report listing all of the Agents who were logged into Skillset 1, including multi-Skillset Agents, and the report will include all of the activity of those Agents, irrespective of the Skillset of the call they handled. If this was not the case, and the report was limited to the Agent activity for the requested Skillset only, you would need to run the same report for each Skillset that each of the multi-Skillset Agents was logged into, to see a full picture of their activity. Voice and Multimedia Calls Nortel Networks Reporting for Call Center reports on both ‘normal’ voice calls and calls conducted through the use of Nortel Networks Multimedia Call Center. Direct and Indirect Calls From the point of view of any given Skillset, Direct Calls are calls that were presented directly to that Skillset. That is, the incoming caller was handled by the Call Routing and was presented by the Call Routing directly to the Skillset in question. Indirect Calls arrived in the Skillset in some other way, such as overflowing from another Skillset or being manually transferred to the Skillset queue by an Agent from another Skillset. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 126 Reports That is, any way a Call can arrive into a Skillset other than being a regular Call Center Call presented Directly to the Skillset (as described above) is counted as an Indirect Call. Whether the call overflowed to the Skillset in question, or was moved to this Skillset by the Move to Queue Call Routing step, or whether it was manually transferred to the Skillset Control Dn, it is counted as an Indirect Call. The total of the Direct calls is the number of calls that rang into the Skillset (how many callers they had). The total of the Indirect calls is the number of calls the Skillset handled that were originally in the system elsewhere, before they found their way to this Skillset. Calls and Call Transactions Calls that are handled within your Call Center are sometimes passed amongst the Skillsets by Agent activities such as transferring a call to the Control Dn of another Skillset or by transferring a call directly to the Agent of another Skillset. This gives rise to separate phases of the call. The portion handled by the first Agent and the subsequent handling by other Agents or other components of your Call Center (such as voice mail) are each counted as a separate phase of the call. Because a call can be transferred back and forth between Skillsets and Agents, a call may therefore have any number of these handling phases. Each of these phases is called a transaction. When two or more Agents handle a single call the various portions of the call are called Call Transactions. Tracking the separate transactions of a Call in this way allows a more accurate and readily understood representation of the activity within your Call Center. Call Transactions and the Direct and Indirect Calls If an incoming Call Center call is handled within a single transaction, that transaction will also be either a Direct Call or an Indirect Call, and the Direct and Indirect columns of the reports will reflect this. However, if an incoming Call Center call is handled by a series of transactions, the second and other following transactions will not affect the Direct Call and Indirect Call columns, because these other transactions are not new Incoming Calls presented to the Skillset. This prevents the transferred portions of the calls skewing such statistics as the number of incoming calls presented to the Skillset, or the Average Waiting time, for example. However, if one of the secondary transactions was a transfer of the call to the Control Dn of a Skillset, that call will appear as a new incoming call in that Skillset in the Indirect column, as this is a queued call that has to be presented to an Agent and answered. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Reports 127 In-Progress Calls In-progress calls are not included in the reports. The reports will only display information on calls that have been completed by the time the report has been requested. Report Headers Each report will show a header of information which will contain: • • • • • • The Company Name (from the Company Details Page, see page 45) The Report Title The Period the report covers (start time and date and an end time and date) The time and date when the report was created The time and date when the report data was obtained from the Call Center The Skillsets included in the report Figure 91 Example Report Header Report Viewer Toolbar When reports have been generated on screen, they are displayed within the report viewer window. The report viewer has a toolbar, shown below. The toolbar allows you to: • Print the report • Export the report • Specify the magnification of the report on screen • Navigate through the report if there are more than one page in the report Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 128 Reports Figure 92 Report Viewer Toolbar Note: The Preview Tab is a label informing you that you are viewing a print preview of the report. It is not a button. Clicking on it will have no action. It is purely descriptive. Printing a Report Clicking on the printer icon opens the printer window, shown below. Figure 93 Report Printer Selection Window This window allows you to select a printer from the list of available printers. This is the printer the report will be generated on. You may specify the number of copies you wish to have printed, and if the report contains several pages you can choose to print the whole report, the page you are currently viewing or a selection of pages. The Preferences button allows you to specify settings such as paper orientation and size. To make sure your printed report correctly fits the paper you are using, you must ensure that you have selected the correct paper size and that you have set the magnification of the report to Page Width (see Page 130). Exporting A Report Clicking on the export report icon opens the export report window, shown below. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Reports 129 Figure 94 Export Report Window File Format Select the desired format from the File Format: drop down menu. The available formats are: Export Format Name Extension Required Viewer Crystal Reports native format .rpt Crystal Reports Microsoft Excel .xls Microsoft Excel or Microsoft Excel Viewer Microsoft Excel (data only) .xls Microsoft Excel or Microsoft Excel Viewer (same as ‘Microsoft Excel’ format above, but in a ‘naked’ format without the shading, highlighting and other report formatting) Microsoft Word .doc Microsoft Word or Word Document Viewer Rich Text Format Adobe Acrobat .rtf Any RTF aware editor or file viewer .pdf Adobe Acrobat Table of Available Report Export Formats Exported File Name and Location You must provide a file name for the exported report. You can optionally provide a file path. If you do not specify a path way in the file name, the file is placed on your desktop. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 130 Reports Note: If you do not specify a file extension of the appropriate type, Windows will not know what file format of the exported report, and will not know what application to use to view it. Pick the appropriate extension from the table above. If you click on the Browse button an explorer style tool allows you to browse to the desired location in which you wish to have the reported exported. Note: If you use the Browse tool it will automatically provide a file extension of the correct type, unless you have specified your own file extension. Page Range You may specify to export the entire report or to export a range of pages. To export the entire report click and highlight the All radio button. To specify a page range, click and highlight the Pages radio button and specifying the start and end page of the section you wish to have exported, in the From and To fields. Note that the All radio button and From and To fields will be greyed out if there is only a single page in the report. Exporting the Report When you have specified the settings you wish to use, such as file name and file format, click on the OK button to export the report. When the report has been exported Nortel Networks Reporting for Call Center will offer to open it to allow you to view it. Note: If you do not have the appropriate viewer installed on your PC then Nortel Networks Reporting for Call Center will not be able to open it to allow you to view it. You must also have used the appropriate file extension for the selected file format. Report Magnification The required report magnification can be chosen from the drop down menu. Note: To make sure your printed report fits the paper in your printer: you must select Page Width from this menu, and ensure that you have selected the correct paper size in the Report Printer Selection Window (see Page 128). Note that once you have selected Page Width, the displayed value reflects the actual magnification, it does not display the text ‘Page Width’. Report Navigation The Arrow head icons and the page field can be used to move forwards or backwards one page, directly to the first or last page or directly to a specific page. Typing a page number into the page field and pressing the Enter key will move you directly to that field. All of the navigation icons will show a tool tip if you position the mouse pointer over them and wait for a moment. Searching for Text Within A Report To locate a string or phrase within the report, click on the Search Text icon (the binoculars). This will allow you to enter your search text. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Reports 131 This could be used to look for a specific Agent in a large Agent Activity report, or to locate a particular Calling Line ID in the Abandoned Calling Line ID report, for example. Using the Reports Selecting the Reports option presents you with the Report Menu page, show below. Each of the reports is listed in turn. To obtain a report click on the button labelled with the report you wish to view. Figure 95 Report Menu Page Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 132 Reports Get latest Call Center Data Button This button causes Nortel Networks Reporting for Call Center to request the most recent report data from the Call Center. For example, if you have specified that Nortel Networks Reporting for Call Center should poll the Call Center every 30 minutes for report data, by clicking on the Get Latest Call Center Data button you ensure that the most recent data is received from the Call Center before the reports are generated. This means that any Call Center activity which has occurred since the last Report Data update is included in the reports. When the reports page is first displayed or whenever the button has been clicked the button is disabled and a short countdown shows the seconds left until it can be used again. This prevents repeated, rapid requests being made. Answered Calls Report Clicking on the Answered Call Report button presents you with the Answered Calls Report Skillsets page, shown below. This page allows you to select the Skillsets you wish to have included in the report, and to specify the time period you wish the report to cover. The time period is specified by providing a From Date and From Time and a To Date and a To Time. The From Date specifies the first date you wish to have included in the report. Information from days before the From Date will not be included in the report. The From Time specifies the time on the From Date from which you wish to have data included in the report. Information from times before the From Time on the From Date will not be included in the report. The To Date specifies the last date you wish to have included in the report. Information from days after the To Date will not be included in the report. The To Time specifies the time on the To Date after which data will not be included in the report. Information from times after the To Time on the To Date will not be included in the report. Drop down menus allow you to choose dates and time values. The Answered Calls Report Skillsets page allows you to select which Skillsets you wish to have included within the report. • • For a discussion of using Skillset Selection lists see page 60. For a discussion on using Favourites, see page 61. Our example User Mary Smith has used her Dev&Train Favourite to highlight and select the Development and Training Skillsets. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Reports 133 Figure 96 Answered Calls Report Skillsets Page Mary Smith has specified that her report should run from the start of day (00:00) on November 30th, 2003 up to 23:59 on November 30th, 2003, and it should include information from the Development and Training Skillsets. Clicking on the Submit button generates the report. This is shown below. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 134 Reports Figure 97 Answered Calls Report For each Skillset the total number of calls is displayed, together with a breakdown of the number and percentage of calls that were answered within each of the Answered Time Bins. For a discussion of Time Bins, see page 50. This reports shows how long those calls that have been answered by your Call Center waited before they were connected to an Agent. Voice calls and Multimedia calls are listed separately and totalled for each Skillset, and for the report total. Abandoned Call Report Clicking on the Abandoned Call Report button presents you with the Abandoned Calls Report Skillsets page, shown below. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Reports 135 Figure 98 Abandoned Call Report Skillset Page This page allows you to select the Skillsets you wish to have included in the report, and to specify the time period you wish the report to cover. The time period is specified by providing a From Date and From Time and a To Date and a To Time. The From Date specifies the first date you wish to have included in the report. Information from days before the From Date will not be included in the report. The From Time specifies the time on the From Date from which you wish to have data included in the report. Information from times before the From Time on the From Date will not be included in the report. The To Date specifies the last date you wish to have included in the report. Information from days after the To Date will not be included in the report. The To Time specifies the time on the To Date after which data will not be included in the report. Information from times after the To Time on the To Date will not be included in the report. Drop down menus allow you to choose dates and time values. The Abandoned Calls Report Skillsets page allows you to select which Skillsets you wish to have included within the report. • • For a discussion of using Skillset Selection lists see page 60. For a discussion on using Favourites, see page 61. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 136 Reports Our example User Mary Smith has used her Dev&Train Favourite to highlight and select the Development and Training Skillsets. Clicking on the Submit button generates the report. This is shown below. Figure 99 Abandoned Call Report For each Skillset the total number of calls is displayed, together with a breakdown of the number and percentage of calls that abandoned within each of the Abandoned Time Bins. For a discussion of Time Bins, see page 50. This report shows how long those calls abandoned waited before they hung up. An Abandoned call is a call that did not get successfully answered. The incoming caller terminated the call before they were connected to an Agent. Voice calls and Multimedia calls are listed separately and totalled for each Skillset, and for the report total. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Reports 137 Abandoned Calling Line ID Report Clicking on the Abandoned Calling Line ID Report button presents you with the Abandoned Calling Line ID Report Skillsets page, shown below. Figure 100 Abandoned Calling Line ID Skillset page This page allows you to select the Skillsets you wish to have included in the report, and to specify the time period you wish the report to cover. The time period is specified by providing a From Date and From Time and a To Date and a To Time. The From Date specifies the first date you wish to have included in the report. Information from days before the From Date will not be included in the report. The From Time specifies the time on the From Date from which you wish to have data included in the report. Information from times before the From Time on the From Date will not be included in the report. The To Date specifies the last date you wish to have included in the report. Information from days after the To Date will not be included in the report. The To Time specifies the time on the To Date after which data will not be included in the report. Information from times after the To Time on the To Date will not be included in the report. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 138 Reports Drop down menus allow you to choose dates and time values. The Abandoned Calling Line ID Report Skillsets page allows you to select which Skillsets you wish to have included within the report. • • For a discussion of using Skillset Selection lists see page 60. For a discussion on using Favourites, see page 61. Our example User Mary Smith has used her Dev&Train Favourite to highlight and select the Development and Training Skillsets. Clicking on the Submit button generates the report. This is shown below. Figure 101 Abandoned Calling Line ID Report For each Skillset and for a report total, the calls that abandoned are shown. The date and time are displayed for each abandoned call, together with the Calling Line ID and the time the call waited before it abandoned. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Reports 139 Agent Capacity Report Clicking on the Agent Capacity Report button presents you with the Agent Capacity Report Skillsets page, shown below. Figure 102 Agent Capacity Report Skillsets page This page allows you to select the Skillsets you wish to have included in the report, and to specify the time period you wish the report to cover. The time period is specified by providing a From Date and From Time and a To Date and a To Time. Note that the report is agent based, not Skillset based. This means that when you request a report on a Skillset, the report will include all of the Agents who were logged into that Skillset during the requested period. For Multi-Skillset Agents the report will include all of the activity of the Multi-Skillset Agents, for all Skillsets into which they were signed during the report period. If this was not the case, and the report was limited to the Agent activity for the requested Skillset only, you would need to run the same report for each Skillset that each of the Multi-Skillset Agents was logged into, to see a full picture of their activity. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 140 Reports Note that the report is agent based, not Skillset based. This means that when you request a report on a Skillset, the report will include all of the Agents who were logged into that Skillset during the requested period. For Multi-Skillset Agents the report will include all of the activity of the Multi-Skillset Agents, for all Skillsets into which they were signed during the report period. If this was not the case, and the report was limited to the Agent activity for the requested Skillset only, you would need to run the same report for each Skillset that each of the Multi-Skillset Agents was logged into, to see a full picture of their activity. The From Date specifies the first date you wish to have included in the report. Information from days before the From Date will not be included in the report. The From Time specifies the time on the From Date from which you wish to have data included in the report. Information from times before the From Time on the From Date will not be included in the report. The To Date specifies the last date you wish to have included in the report. Information from days after the To Date will not be included in the report. The To Time specifies the time on the To Date after which data will not be included in the report. Information from times after the To Time on the To Date will not be included in the report. Drop down menus allow you to choose dates and time values. The Agent Capacity Report Skillsets page allows you to select which Skillsets you wish to have included within the report. • • For a discussion of using Skillset Selection lists see page 60. For a discussion on using Favourites, see page 61. Our example User Mary Smith has used her Dev&Train Favourite to highlight and select the Development and Training Skillsets. Clicking on the Submit button generates the report. This is shown below. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Reports 141 Figure 103 Agent Capacity Report Whenever there are Agents logged into a Skillset but none of those Agents are available to take an Incoming Call Center call, Nortel Networks Reporting for Call Center records how long that state continues. That is, it records the time which elapses before an Agent becomes available to take an Incoming Call Center call. Note that this is recorded whether there are any incoming Call Center calls or not. For each Skillset that was selected, this reports shows the total number of instances when there were no Agents available to take an incoming Call Center call, and the total duration of all of those instances added together. Help Request Report Clicking on the Help Request Report button presents you with the Help Request Report page, shown below. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 142 Reports Figure 104 Help Request Report page This page allows you to specify the time period you wish the report to cover. The time period is specified by providing a From Date and From Time and a To Date and a To Time. The From Date specifies the first date you wish to have included in the report. Information from days before the From Date will not be included in the report. The From Time specifies the time on the From Date from which you wish to have data included in the report. Information from times before the From Time on the From Date will not be included in the report. The To Date specifies the last date you wish to have included in the report. Information from days after the To Date will not be included in the report. The To Time specifies the time on the To Date after which data will not be included in the report. Information from times after the To Time on the To Date will not be included in the report. Drop down menus allow you to choose dates and time values. Click on the Submit button to view the report. Click on the Cancel button to return to the Report Menu page. The Help Request Report is shown below. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Reports 143 Figure 105 Help Request Report This report lists each Supervisor (that has answered a Help Request) together with the details of the Help requests they answered. Supervisor ID Indicates the Call Center ID of the Supervisor who answered the Help Request. Supervisor Name Indicates the name of the Supervisor who answered the Help Request. Time Indicates the time at which the Help Request was answered. Date Indicates the date on which the Help Request was answered. CLID Indicates the CLID of the incoming call on which the Agent who made the Help Request was active at the time they made the Help Request. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 144 Reports Agent ID Indicates the Call Center ID of the Agent who made the Help Request. Agent Name Indicates the name of the Agent who made the Help Request. Call Average Report Clicking on the Call Average Report button presents you with the Call Average Report Skillsets page, shown below. Figure 106 Call Average Report Skillset page This page allows you to select the Skillsets you wish to have included in the report, and to specify the time period you wish the report to cover. The time period is specified by providing a From Date and From Time and a To Date and a To Time. The From Date specifies the first date you wish to have included in the report. Information from days before the From Date will not be included in the report. The From Time specifies the time Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Reports 145 on the From Date from which you wish to have data included in the report. Information from times before the From Time on the From Date will not be included in the report. The To Date specifies the last date you wish to have included in the report. Information from days after the To Date will not be included in the report. The To Time specifies the time on the To Date after which data will not be included in the report. Information from times after the To Time on the To Date will not be included in the report. Drop down menus allow you to choose dates and time values. The Call Average Report Skillsets page allows you to select which Skillsets you wish to have included within the report. • • For a discussion of using Skillset Selection lists see page 60. For a discussion on using Favourites, see page 61. Our example User Mary Smith has used her Dev&Train Favourite to highlight and select the Development and Training Skillsets. Clicking on the Submit button generates the report. Figure 107 Call Average Report Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 146 Reports For each Skillset and for a report total, the number of calls and their average is displayed for three statistics. Voice calls and Multimedia calls are listed separately and totalled for each Skillset, and for the report total. Call Center Call Average Time To Answer The Call Center Call Average Time To Answer column holds the average time before a Call was answered. This statistic tracks Direct and Indirect Calls, not call transactions. This can be used to determine the average time that answered calls had to wait before they were answered. Call Center Call Average Time To Abandon The Call Center Call Average Time To Abandon column holds the average time before a Call abandoned. This statistic tracks Direct and Indirect Calls, not transactions. This can be used to determine how long on average abandoned calls waited for before they abandoned. Call Center Call Transactions Average Incoming Duration The Call Center Call Transactions Average Incoming Duration column holds the average duration of each call transaction. This statistic tracks call transactions, not calls, so a call that is answered in one Skillset and transferred to the Control Dn of another Skillset (or even back to the Control Dn of the same Skillset) will have a call duration for each portion of the call. Both portions will be included in the reports. Agent Average Report Clicking on the Agent Average Report button presents you with the Agent Average Report Skillsets page, shown below. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Reports 147 Figure 108 Agent Average Report Skillset Selection Page This page allows you to select the Skillset you wish to have included in the report, and to specify the time period you wish the report to cover. Note that the report is agent based, not Skillset based. This means that when you request a report on a Skillset, the report will include all of the Agents who were logged into that Skillset during the requested period. For Multi-Skillset Agents the report will include all of the activity of the Multi-Skillset Agents, for all Skillsets into which they were signed during the report period. If this was not the case, and the report was limited to the Agent activity for the requested Skillset only, you would need to run the same report for each Skillset that each of the Multi-Skillset Agents was logged into, to see a full picture of their activity. The time period is specified by providing a From Date and From Time and a To Date and a To Time. The From Date specifies the first date you wish to have included in the report. Information from days before the From Date will not be included in the report. The From Time specifies the time on the From Date from which you wish to have data included in the report. Information from times before the From Time on the From Date will not be included in the report. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 148 Reports The To Date specifies the last date you wish to have included in the report. Information from days after the To Date will not be included in the report. The To Time specifies the time on the To Date after which data will not be included in the report. Information from times after the To Time on the To Date will not be included in the report. Drop down menus allow you to choose dates and time values. Note: You can only select a single Skillet to be included in this report. The report will include all Agents who have signed into the selected Skillset during the requested time period. However, the report will include ALL of the information for those Agents for that time period, even if they were signed into multiple Skillsets and were handling calls from other Skillsets. This means that you do not have to specify a combination of different reports to get the complete picture for the multiple Skillset Agents who were signed into the chosen Skillset. For example, if you have an Agent signed into Skillset 1, another signed into Skillsets 1 and 2, and another signed into Skillsets 1 and 3, by choosing Skillset 1 as the Skillset to report one, you will see all three Agents in your report and the data shown for them will be their complete Activity in all Skillsets for the requested period. For a version of this report categorised by Agent, see the Agent Average report by Skillset on Page 191. Clicking on the Show Report button generates the report. This is shown below. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Reports 149 Figure 109 Agent Average Report For each Agent the average durations of three Call Center activities are displayed. These activities are Call Center Call Transactions Average Incoming Duration, the Average Outgoing Call Duration and the Average Break Time Duration. For the Incoming and Outgoing Call Durations, the number of calls is also provided. This report provides an easy way to compare the average durations of different Agents. If the Incoming Call Duration for one Agent is markedly longer than the duration of the other Agents, this report will show up the anomaly. This might indicate for example, that the Agent requires some training, or perhaps it indicates that they are providing extra care and attention to their callers. Agent Profile Report Clicking on the Agent Profile Report button presents you with the Agent Profile Report Skillsets page, shown below. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 150 Reports Figure 110 Agent Profile Report Skillset page This page allows you to select the Skillset you wish to have included in the report, and to specify the time period you wish the report to cover. The time period is specified by providing a From Date and From Time and a To Date and a To Time. Note that the report is agent based, not Skillset based. This means that when you request a report on a Skillset, the report will include all of the Agents who were logged into that Skillset during the requested period. For Multi-Skillset Agents the report will include all of the activity of the Multi-Skillset Agents, for all Skillsets into which they were signed during the report period. If this was not the case, and the report was limited to the Agent activity for the requested Skillset only, you would need to run the same report for each Skillset that each of the Multi-Skillset Agents was logged into, to see a full picture of their activity. The From Date specifies the first date you wish to have included in the report. Information from days before the From Date will not be included in the report. The From Time specifies the time on the From Date from which you wish to have data included in the report. Information from times before the From Time on the From Date will not be included in the report. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Reports 151 The To Date specifies the last date you wish to have included in the report. Information from days after the To Date will not be included in the report. The To Time specifies the time on the To Date after which data will not be included in the report. Information from times after the To Time on the To Date will not be included in the report. Drop down menus allow you to choose dates and time values. Note: You can only select a single Skillet to be included in this report. The report will include all Agents who have signed into the selected Skillset during the requested time period. However, the report will include ALL of the information for those Agents for that time period, even if they were signed into multiple Skillsets and were handling calls from other Skillsets. This means that you do not have to specify a combination of different reports to get the complete picture for the multiple Skillset Agents who were signed into the chosen Skillset. For example, if you have an Agent signed into Skillset 1, another signed into Skillsets 1 and 2, and another signed into Skillsets 1 and 3, by choosing Skillset 1 as the Skillset to report one, you will see all three Agents in your report and the data shown for them will be their complete Activity in all Skillsets for the requested period. Clicking on the Show Report button generates the report. This is shown below. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 152 Reports Figure 111 Agent Profile Report For each Agent the following are displayed. Logged In Time This is the cumulative duration of all of the Log In sessions the Agent conducted during the period of the report. Available Time This is the cumulative duration of all of the Available time the Agent had during the period of the report. An Agent is Available when they are free to take an Incoming Call Center Call. Not Ready Time This is the cumulative duration of all of the Not Ready time the Agent had during the period of the report. An Agent is Not Ready when they have invoked the Make Not Ready feature. Break Time This is the cumulative duration of all of the Break Time the Agent had during the period of the report. An Agent is in Break Time following an Incoming Call Center Call. This is also known as Wrap-Up. The Skillset supervisor allocates the amount of Break Time that the Agents will receive. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Reports 153 Answered Incoming Call Center Calls This is the number of Incoming Call Center Calls that the Agent handled during the period of the report. The sum of the durations of these calls is given in the following column. Incoming Time This is the cumulative duration of all of the Incoming Call Center Calls that the Agent handled during the period of the report. The number of calls that this duration represents is given in the preceding column. Outgoing Calls This is the number of Outgoing Calls that the Agent made during the period of the report. The sum of the durations of these calls is given in the following column. Outgoing Time This is the cumulative duration of all of the Outgoing Calls that the Agent handled during the period of the report. The number of calls that this duration represents is given in the preceding column. Agent Activity Report Clicking on the Agent Activity Report button presents you with the Agent Activity Report Skillsets page, shown below. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 154 Reports Figure 112 Agent Activity Report Skillsets page This page allows you to select the Skillsets you wish to have included in the report, and to specify the time period you wish the report to cover. The time period is specified by providing a From Date and From Time and a To Date and a To Time. Note that the report is agent based, not Skillset based. This means that when you request a report on a Skillset, the report will include all of the Agents who were logged into that Skillset during the requested period. For Multi-Skillset Agents the report will include all of the activity of the Multi-Skillset Agents, for all Skillsets into which they were signed during the report period. If this was not the case, and the report was limited to the Agent activity for the requested Skillset only, you would need to run the same report for each Skillset that each of the Multi-Skillset Agents was logged into, to see a full picture of their activity. For a Skillset based version of this report, see the Agent Activity Report by Skillset on Page193. The From Date specifies the first date you wish to have included in the report. Information from days before the From Date will not be included in the report. The From Time specifies the time Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Reports 155 on the From Date from which you wish to have data included in the report. Information from times before the From Time on the From Date will not be included in the report. The To Date specifies the last date you wish to have included in the report. Information from days after the To Date will not be included in the report. The To Time specifies the time on the To Date after which data will not be included in the report. Information from times after the To Time on the To Date will not be included in the report. Drop down menus allow you to choose dates and time values. The Agent Activity Report Skillsets page allows you to select which Skillsets you wish to have included within the report. • • For a discussion of using Skillset Selection lists see page 60. For a discussion on using Favourites, see page 61. Our example User Mary Smith has used her Dev&Train Favourite to highlight and select the Development and Training Skillsets. Clicking on the Submit button generates the report. This is shown below. Figure 113 Agent Activity Report Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 156 Reports For each Agent within the report, the following statistics are displayed. Logged In Time This is the cumulative duration of all of the Log In sessions the Agent conducted during the period of the report. Incoming Call Center This is the cumulative duration of all of the Incoming Call Center Calls that the Agent handled during the period of the report. Incoming Non-Call Center This is the cumulative duration of all of the Incoming Non-Call Center Calls that the Agent handled during the period of the report. These are calls that have not come through the Call Center routing, such as direct calls to the Agent on their DDI line, for example. Outgoing Call Time This is the number of Outgoing Calls that the Agent made during the period of the report. Break Time This is the cumulative duration of all of the Break Time the Agent had during the period of the report. An Agent is in Break Time following an Incoming Call Center Call. This is also known as Wrap-Up. The Skillset supervisor allocates the amount of Break Time that the Agents will receive. Not Ready Time This is the cumulative duration of all of the Not Ready time the Agent had during the period of the report. An Agent is Not Ready when they have invoked the Make Not Ready feature. Supervisory Monitoring This is the cumulative duration of all of Supervisory Monitor sessions the Agent undertook during the period of the report. An Agent can only perform Supervisory Monitoring if they have been created as a Skillset Supervisor within the Call Center. Internal Call Time This is the cumulative duration of all of the Internal Calls that the Agent placed or answered during the period of the report. Internal Calls are also called Intercom Calls. Agent Audit Report Clicking on the Agent Audit Report presents you with the Agent Audit Report Skillset Selection page, shown below. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Reports 157 Figure 114 Agent Audit Report Skillset Selection page This page allows you to select the Skillsets you wish to have included in the report, and to specify the time period you wish the report to cover. The time period is specified by providing a From Date and From Time and a To Date and a To Time. The From Date specifies the first date you wish to have included in the report. Information from days before the From Date will not be included in the report. The From Time specifies the time on the From Date from which you wish to have data included in the report. Information from times before the From Time on the From Date will not be included in the report. The To Date specifies the last date you wish to have included in the report. Information from days after the To Date will not be included in the report. The To Time specifies the time on the To Date after which data will not be included in the report. Information from times after the To Time on the To Date will not be included in the report. Drop down menus allow you to choose dates and time values. The Agent Audit Report Skillsets page allows you to select which Skillsets you wish to have included within the report. • For a discussion of using Skillset Selection lists see page 60. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 158 Reports • For a discussion on using Favourites, see page 61. Our example User Mary Smith has used her Dev&Train Favourite to highlight and select the Development and Training Skillsets. Clicking on the Submit button presents you with the Agent Selection page, shown below. Figure 115 Agent Selection Page This page allows you to specify which Agents you wish to have included in the report. You can click on a single Agent to highlight and select a single Agent, you can click the Select All button to highlight and select all Agents, and you can hold down the Control (CTRL) key, and click on individual Agents to highlight and select a selection of Agents on which to report. Note that if you have no Agents created in the Call Center or if no Agents have ever logged into the particular Skillsets you have selected and performed the activity on which you are reporting, you will be presented with Agent Selection page with a message informing you that you have no Agents to choose from. This is shown below. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Reports 159 Figure 116 Agent Selection page with No Agents Available Clicking on the Show Report button (which is visible on the Agent Selection page when there are some Agents available to select) presents you with the Agent Audit report, shown below. This report shows a detailed breakdown of the activities undertook by the specified Agents for the period of the report. Note that this report is intended to provide a highly detailed picture of the Agent activities, and is intended to be used to produce reports that specify a short report period. If the report period is long (more than an hour) or there are many Agents included in the report this report could be very long. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 160 Reports Figure 117 Agent Audit Report Agent ID Indicates the Call Center Log In Id of the Agent. Agent Name Indicates the Call Center name for the Agent. Time and Date Indicates the start time and date of an Activity. Activity Describes the Activity the Agent undertook at the specified time and date. Activity Duration The length of time the Agent undertook the specified Activity for. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Reports 161 Activity Code Report by Skillset Clicking on the Activity Code Report by Skillset button presents you with the Activity Code Report by Skillset Skillset Selection page, shown below. Figure 118 Activity Code Report By Skillset Skillset page This page allows you to select the Skillsets you wish to have included in the report, and to specify the time period you wish the report to cover. The time period is specified by providing a From Date and From Time and a To Date and a To Time. The From Date specifies the first date you wish to have included in the report. Information from days before the From Date will not be included in the report. The From Time specifies the time on the From Date from which you wish to have data included in the report. Information from times before the From Time on the From Date will not be included in the report. The To Date specifies the last date you wish to have included in the report. Information from days after the To Date will not be included in the report. The To Time specifies the time on the To Date after which data will not be included in the report. Information from times after the To Time on the To Date will not be included in the report. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 162 Reports Drop down menus allow you to choose dates and time values. The Activity Code Report by Skillset Skillsets page allows you to select which Skillsets you wish to have included within the report. • • For a discussion of using Skillset Selection lists see page 60. For a discussion on using Favourites, see page 61. Our example User Mary Smith has used her Dev&Train Favourite to highlight and select the Development and Training Skillsets. Clicking on the Submit button presents you with the Activity Code Selection page, shown below. Figure 119 Select Activity Code page This page allows you to specify which Activity Codes you wish to have included in the report. You can click on a single Activity Code to highlight and select a single Activity Code, you can click the Select All button to highlight and select all Activity Codes, and you can hold down the Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Reports 163 Control (CTRL) key, and click on individual Activity Codes to highlight and select a selection of Activity Codes on which to report. Note that if you have no Activities created in the Call Center or if no Agents have ever entered an Activity Code, you will be presented with Select Activity Codes page, with a message informing you that you have no Activity Codes to choose from. This is shown below. Figure 120 Select Activity Codes page – No Activity Codes Clicking on the Show Report button (which is visible on the Activity Code Selection page when there are some Activity Codes available to select) presents you with the Activity Code Report by Skillsets report, shown below. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 164 Reports Figure 121 Activity Code Report by Skillset This report show by Skillset, which Agents entered Activity Codes. A total is provided for each Activity Code giving a total time for which the Activities were entered, the number of individual pegs and the average time devoted to that activity. Activity Code Indicates which Activity Code was entered. Skillset Indicates which Skillset the call was associated with when the Activity Code was entered. Activity Time Total duration of all of the instances when that Activity Code was entered. Number of Pegs Indicates the number of times that Activity Code was entered. Average Time Average time devoted to that Activity. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Reports 165 Activity Code Report by Agent Clicking on the Activity Code Report by Agent button presents you with the Activity Code Report by Agent Skillset Selection page, shown below. Figure 122 Activity Code Report By Agent Skillset page This page allows you to select the Skillsets you wish to have included in the report, and to specify the time period you wish the report to cover. The time period is specified by providing a From Date and From Time and a To Date and a To Time. The From Date specifies the first date you wish to have included in the report. Information from days before the From Date will not be included in the report. The From Time specifies the time on the From Date from which you wish to have data included in the report. Information from times before the From Time on the From Date will not be included in the report. The To Date specifies the last date you wish to have included in the report. Information from days after the To Date will not be included in the report. The To Time specifies the time on the To Date after which data will not be included in the report. Information from times after the To Time on the To Date will not be included in the report. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 166 Reports Drop down menus allow you to choose dates and time values. The Activity Code Report by Agent Skillsets Selection page allows you to select which Skillsets you wish to have included within the report. • • For a discussion of using Skillset Selection lists see page 60. For a discussion on using Favourites, see page 61. Our example User Mary Smith has used her Dev&Train Favourite to highlight and select the Development and Training Skillsets. Clicking on the Submit button presents you with the Activity Code Selection page, shown below. Figure 123 Select Activity Code page This page allows you to specify which Activity Codes you wish to have included in the report. You can click on a single Activity Code to highlight and select a single Activity Code, you can click the Select All button to highlight and select all Activity Codes, and you can hold down the Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Reports 167 Control (CTRL) key, and click on individual Activity Codes to highlight and select a selection of Activity Codes on which to report. Note that if you have no Activities created in the Call Center or if no Agents have ever entered an Activity Code, you will be presented with Select Activity Codes page, with a message informing you that you have no Activity Codes to choose from. This is shown below. Figure 124 Select Activity Codes page – No Activity Codes Clicking on the Show Report button (which is visible on the Activity Code Selection page when there are some Activity Codes available to select) presents you with the Activity Code Report by Agent report, shown below. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 168 Reports Figure 125 Agent Activity Code Report by Agent This report show by Agent, which Activity Codes were entered. A total is provided for each Activity Code per Agent giving a total time for which the Activities were entered, the number of individual pegs and the average time devoted to that activity. Activity Code Indicates which Activity Code was entered. Agent Indicates the Agent Name and ID who entered the Activity Codes. Activity Time Total duration of all of the instances when that Activity Code was entered. Number of Pegs Indicates the number of times that Activity Code was entered. Average Time Average time devoted to that Activity. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Reports 169 Activity Code Report by # of Pegs Clicking on the Activity Code Report by # of Pegs button presents you with the Activity Code Report by # Pegs Skillset Selection page, shown below. Figure 126 Activity Code Report By # of Pegs Skillset page This page allows you to select the Skillsets you wish to have included in the report, and to specify the time period you wish the report to cover. The time period is specified by providing a From Date and From Time and a To Date and a To Time. The From Date specifies the first date you wish to have included in the report. Information from days before the From Date will not be included in the report. The From Time specifies the time on the From Date from which you wish to have data included in the report. Information from times before the From Time on the From Date will not be included in the report. The To Date specifies the last date you wish to have included in the report. Information from days after the To Date will not be included in the report. The To Time specifies the time on the To Date after which data will not be included in the report. Information from times after the To Time on the To Date will not be included in the report. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 170 Reports Drop down menus allow you to choose dates and time values. The Activity Code Report by # of Pegs Skillset page allows you to select which Skillsets you wish to have included within the report. • • For a discussion of using Skillset Selection lists see page 60. For a discussion on using Favourites, see page 61. Our example User Mary Smith has used her Dev&Train Favourite to highlight and select the Development and Training Skillsets. Clicking on the Submit button presents you with the Activity Code Selection page, shown below. Figure 127 Select Activity Code page This page allows you to specify which Activity Codes you wish to have included in the report. You can click on a single Activity Code to highlight and select a single Activity Code, you can click the Select All button to highlight and select all Activity Codes, and you can hold down the Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Reports 171 Control (CTRL) key, and click on individual Activity Codes to highlight and select a selection of Activity Codes on which to report. Note that if you have no Activities created in the Call Center or if no Agents have ever entered an Activity Code, you will be presented with Select Activity Code page, with a message informing you that you have no Activity Codes to choose from. This is shown below. Figure 128 Select Activity Codes page – No Activity Codes Clicking on the Show Report button (which is visible on the Activity Code Selection page when there are some Activity Codes available to select) presents you with the Activity Code Report by # of Pegs report, shown below. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 172 Reports Figure 129 Agent Activity Code Report by Number of Pegs This report shows, by Agent, which Activity Codes were entered. A total is provided for each Activity Code per Agent giving a total time for which the Activities were entered, the number of individual pegs and the average time devoted to that activity. Agent Indicates the Agent Name and ID who entered the Activity Codes. Activity Indicates which Activity Code was entered. Activity Time Total duration of all of the instances when that Activity Code was entered. Number of Pegs Indicates the number of times that Activity Code was entered. Average Time Average time devoted to that Activity. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Reports 173 Summary Report Clicking on the Summary Report button presents you with the Summary Report Skillsets page, shown below. Figure 130 Summary Report Skillset page This page allows you to select the Skillsets you wish to have included in the report, and to specify the time period you wish the report to cover. The time period is specified by providing a From Date and From Time and a To Date and a To Time. The From Date specifies the first date you wish to have included in the report. Information from days before the From Date will not be included in the report. The From Time specifies the time on the From Date from which you wish to have data included in the report. Information from times before the From Time on the From Date will not be included in the report. The To Date specifies the last date you wish to have included in the report. Information from days after the To Date will not be included in the report. The To Time specifies the time on the Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 174 Reports To Date after which data will not be included in the report. Information from times after the To Time on the To Date will not be included in the report. Drop down menus allow you to choose dates and time values. The Summary Report Skillsets page allows you to select which Skillsets you wish to have included within the report. • • For a discussion of using Skillset Selection lists see page 60. For a discussion on using Favourites, see page 61. Our example User Mary Smith has used her Dev&Train Favourite to highlight and select the Development and Training Skillsets. Clicking on the Submit button generates the report. This is shown below. Figure 131 Summary Report The following statistics are displayed. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Reports 175 Number of Presented Calls This is the total number of calls that were presented to the Skillets included in this report. These calls might or might not have been answered. This is the total potential calls that could have been answered. No. of Answered Call Transactions This is the total number of call transactions that were answered. If a call is answered by an Agent and transferred to another Agent, each Agent handles a separate Call Transaction. Number of Outgoing Calls This is the number of Outgoing Calls placed by the Agents in the Skillsets included in the report. Number of Abandoned Calls This is the total number of calls that were presented to the Skillsets but the caller disconnected before they were answered. Number of Unstaffed Calls This is the number of calls that were presented to the Skillsets included in this report during periods when there were no Agents logged into take the calls. Average Time To Answer This is the average time the Answered Calls had to wait before they were answered. Average Time To Abandon This is the average time the Abandoned Calls waited for, before they disconnected. Average Outgoing Duration This is the average length of the Outgoing Calls made by the Agents in the Skillsets included in this report. Average Grade of Service % This is the average Grade of Service offered to the incoming callers for the Skillsets included in the report, for the duration of the period of the report. Summary Report Table The following statistics are presented on an hourly or daily basis according to the timescale of the Report period. As the example Report shown has a period of a single day the Time category is divided into Hours. Time The table is divided into Time Slots, which are either Days or Hours according to the period of the Report. Our example report here covers a single day and so the time slots are Hours. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 176 Reports Presented Calls (Direct and Indirect) The total number of calls presented in this time slot. Direct Calls are those that are presented directly to the Skillset. Indirect Calls have been handled by the Call Routing of another Skillset and have either, for example, Overflowed or been manually transferred to this Skillset. Answered Call Transactions The number of call transactions that were answered in this time slot. Abandoned Calls The number of calls which abandoned during this time slot. Calls Handled in Another Skillset The number of calls that were targeted at this Skillset but which were answered in another Skillset due to an Overflow, Move to Queue or other Call Routing option. Outgoing Calls The number of Outgoing Calls that were placed by the Agents in this Skillset during this time slot. Unstaffed Calls The number of calls that arrived in this Skillset, in this time slot, when there were no Agents logged into it. Grade of Service % The Grade of Service offered to incoming callers during this time slot. Summary Report Graphs The Summary Report also provides a selection of Summary Graphs, each of which shows a profile of a single statistic across the time slots of the Report, covering the time period of the Report. These are shown below. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Reports 177 Figure 132 Summary Report Graphs Presented Calls This graph provides a profile of the number of calls that were presented in each time slot of the time period of the Report. Answered Calls This graph provides a profile of the number of calls that were answered in each time slot of the time period of the Report. Abandoned Calls This graph provides a profile of the number of calls that abandoned in each time slot of the time period of the Report. Outgoing Calls This graph provides a profile of the number of Outgoing Calls that were placed by the Agents in the Skillsets included in the Report, in each time slot of the time period of the Report. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 178 Reports Calls Handled In Another Skillset This graph provides a profile of the number of calls that were targeted at the Skillsets included in this Report but which were answered in another Skillset because of some Call Routing action, in each time slot of the time period of the Report. Grade of Service This graph provides a profile of the grade of service offered to the incoming callers during each time slot of the time period of the Report. Call Profile Report Clicking on the Call Profile Report button presents you with the Call Profile Report Skillsets page, shown below. Figure 133 Call Profile report Skillset Selection page This page allows you to select the Skillsets you wish to have included in the report, and to specify the time period you wish the report to cover. The time period is specified by providing a From Date and From Time and a To Date and a To Time. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Reports 179 The From Date specifies the first date you wish to have included in the report. Information from days before the From Date will not be included in the report. The From Time specifies the time on the From Date from which you wish to have data included in the report. Information from times before the From Time on the From Date will not be included in the report. The To Date specifies the last date you wish to have included in the report. Information from days after the To Date will not be included in the report. The To Time specifies the time on the To Date after which data will not be included in the report. Information from times after the To Time on the To Date will not be included in the report. Drop down menus allow you to choose dates and time values. The Call Profile Report Skillsets page allows you to select which Skillsets you wish to have included within the report. • • For a discussion of using Skillset Selection lists see page 60. For a discussion on using Favourites, see page 61. Our example User Mary Smith has used her Dev&Train Favourite to highlight and select the Development and Training Skillsets. Clicking on the Submit button generates the report. This is shown below. This report provides a breakdown of the period of the report into Time slots. The time slots will be in hours or in days, according to the length of the report period. It is by comparing the values from the various time slots that the profile of the period can be observed. A graph is provided in this report to better understand the profile of the period. Call Profile Report Table The following statistics are provided in the Call Profile Report. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 180 Reports Figure 134 Call Profile Report Presented Call Center Indicates the number of calls that were presented to the Skillset in each time slot. There is a breakdown showing the number of calls that were regular voice calls and those which were conducted through the use of Nortel Networks Multimedia Call Center (Multimedia calls). Number Answered Indicates the number of calls that were Answered in each time slot, with a break down showing the number of calls that were regular Voice calls and those which were conducted through the use of Nortel Networks Multimedia Call Center (Multimedia calls). Number Abandoned Indicates the number of calls that were Abandoned in each time slot, with a break down showing the number of calls that were regular voice calls and those which were conducted through the use of Nortel Networks Multimedia Call Center (Multimedia calls). Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Reports 181 Answered by Agents Indicates the number of calls that were Answered by Agents in each time slot, with a break down showing the number of calls that were regular voice calls and those which were conducted through the use of Nortel Networks Multimedia Call Center (Multimedia calls). Answered by Voice Mail Indicates the number of calls that were Answered by Voice Mail in each time slot, with a break down showing the number of calls that were regular Voice calls and those which were conducted through the use of Nortel Networks Multimedia Call Center (Multimedia calls). Answered by Operator Indicates the number of calls that were Answered by the Operator in each time slot, with a break down showing the number of calls that were regular voice calls and those which were conducted through the use of Nortel Networks Multimedia Call Center (Multimedia calls). Answered by Overflow Agent Indicates the number of calls that were Answered by Overflow Agents, in each time slot. Overflow Agents are Agents logged into another Skillset, who are considered to be temporarily logged in to the Skillset which the overflow call was targeted at. A break down shows the number of calls that were regular voice calls and those which were conducted through the use of Nortel Networks Multimedia Call Center (Multimedia calls). Answered by Non-Agent Indicates the number of calls that were Answered by Non-Agents in each time slot, with a break down showing the number of calls that were regular voice calls and those which were conducted through the use of Nortel Networks Multimedia Call Center (Multimedia calls). Calls Handled in Another Skillset Indicates the number of calls that were Answered by the Agents in other Skillsets, in each time slot, with a break down showing the number of calls that were regular voice calls and those which were conducted through the use of Nortel Networks Multimedia Call Center (Multimedia calls). (Calls can be answered in another Skillset because of a routing step such as Move to Queue.) Grade of Service Indicates the Grade of Service offered to incoming callers during each time slot, with a break down showing the number of calls that were regular voice calls and those which were conducted through the use of Nortel Networks Multimedia Call Center (Multimedia calls). Call Profile Report Graph A graph is included on the last page of the Call Profile Report, this is shown below. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 182 Reports Figure 135 Call Profile Report Graph The graph indicates the number of Call Center calls that were Presented, Answered and Abandoned for each time slot across the period of the report. Incoming Call Report Clicking on the Incoming Call Report button presents you with the Incoming Call Report Skillsets page, shown below. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Reports 183 Figure 136 Incoming Call Report Skillset Selection page This page allows you to select the Skillsets you wish to have included in the report, and to specify the time period you wish the report to cover. The time period is specified by providing a From Date and From Time and a To Date and a To Time. The From Date specifies the first date you wish to have included in the report. Information from days before the From Date will not be included in the report. The From Time specifies the time on the From Date from which you wish to have data included in the report. Information from times before the From Time on the From Date will not be included in the report. The To Date specifies the last date you wish to have included in the report. Information from days after the To Date will not be included in the report. The To Time specifies the time on the To Date after which data will not be included in the report. Information from times after the To Time on the To Date will not be included in the report. Drop down menus allow you to choose dates and time values. The Incoming Call Report Skillsets page allows you to select which Skillsets you wish to have included within the report. • For a discussion of using Skillset Selection lists see page 60. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 184 Reports • For a discussion on using Favourites, see page 61. Our example User Mary Smith has used her Dev&Train Favourite to highlight and select the Development and Training Skillsets. Clicking on the Submit button generates the report. This is shown below. Incoming Call Report Table The following statistics are presented in the Incoming Call Report Table. Figure 137 Incoming Call Report Direct Indicates the number of Direct Calls that have been answered in the Skillset. Direct Calls are those calls that have not been handled by the Call Routing of another Skillset, nor by the Agents of another Skillset. They have come via the Call Routing ‘direct’ to the Skillset in question. Separate figures are presented for voice calls and Multimedia Calls (calls conducted through the use of Nortel Networks Call Multimedia Center.) Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Reports 185 Indirect Indicates the number of Indirect Calls that have been answered in the Skillset. Indirect Calls have been handled by the Call Routing of another Skillset or by the Agent so f another Skillset before they arrived in this Skillset. Separate figures are presented for voice calls and Multimedia Calls (calls conducted through the use of Nortel Networks Call Multimedia Center.) Agent Indicates the number of calls that have been answered by the Agents in this Skillset. Separate figures are presented for voice calls and Multimedia Calls (calls conducted through the use of Nortel Networks Call Multimedia Center.) VM Indicates the number of calls that have been answered by the Voice Mail in this Skillset. Separate figures are presented for voice calls and Multimedia Calls (calls conducted through the use of Nortel Networks Call Multimedia Center.) Oper Indicates the number of calls that were presented to this Skillset but which were eventually answered by the Operator. Separate figures are presented for voice calls and Multimedia Calls (calls conducted through the use of Nortel Networks Call Multimedia Center.) Overflow Agent Indicates the number of calls that were presented to this Skillset and which were answered by Overflow Agents. Overflow Agents are Agents in another Skillset, who are automatically temporarily considered to be in the Skillset that the call was originally targeted at. Separate figures are presented for voice calls and Multimedia Calls (calls conducted through the use of Nortel Networks Call Multimedia Center.) Non-Agent Indicates the number of calls that were presented to this Skillset but which were eventually answered by a Non-Agent. Separate figures are presented for voice calls and Multimedia Calls (calls conducted through the use of Nortel Networks Call Multimedia Center.) Calls Abandoned Indicates the number of calls that were presented to this Skillset but which were never answered because the incoming caller cleared down the call before it could be answered. Separate figures are presented for voice calls and Multimedia Calls (calls conducted through the use of Nortel Networks Call Multimedia Center.) Left Skillset via Overflow Table Indicates the number of calls that left the Skillset due to the Call Routing programmed in the Overflow Table. (These calls have left this Skillset, they are not the same as the calls answered by Overflow Agents in this Skillset.) Separate figures are presented for voice calls and Multimedia Calls (calls conducted through the use of Nortel Networks Call Multimedia Center.) Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 186 Reports Left Skillset via Routing Table Indicates the number of calls that left the Skillset due to the Call Routing programmed in the Routing Table. Separate figures are presented for voice calls and Multimedia Calls (calls conducted through the use of Nortel Networks Call Multimedia Center.) Unstaffed Calls Indicates the number of calls that were presented to the Skillset in the periods when there no Agent logged in. Separate figures are presented for voice calls and Multimedia Calls (calls conducted through the use of Nortel Networks Call Multimedia Center.) <P Indicates the number of calls that were answered before the Primary Alert Threshold. (Mutually exclusive to >P and >S.) Separate figures are presented for voice calls and Multimedia Calls (calls conducted through the use of Nortel Networks Call Multimedia Center.) >P Indicates the number of calls that were answered after the Primary Alert Threshold but before the Secondary Alert Threshold. (Mutually exclusive to <P and >S.) Separate figures are presented for voice calls and Multimedia Calls (calls conducted through the use of Nortel Networks Call Multimedia Center.) >S Indicates the number of calls that were answered after the Secondary Alert Threshold. (Mutually exclusive to <P and >P.) Separate figures are presented for voice calls and Multimedia Calls (calls conducted through the use of Nortel Networks Call Multimedia Center.) GOS Indicates the grade of service that was offered to the incoming callers for the period of the report. Separate figures are presented for voice calls and Multimedia Calls (calls conducted through the use of Nortel Networks Call Multimedia Center.) Incoming Call Report Graph On the last page of the report, the following graph is displayed. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Reports 187 Figure 138 Incoming Call Report Graph Total Presented Indicates the total number of calls (both voice and Multimedia Calls) that were presented to the Skillset. Answered Call Indicates the total number of calls (both voice and Multimedia Calls) that were answered in the Skillset. Abandoned Calls Indicates the total number of calls (both voice and Multimedia Calls) that were abandoned in the Skillset. Unstaffed Calls Indicates the total number of calls (both voice and Multimedia Calls) that were presented to the Skillset during those periods when there were no Agents logged in. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 188 Reports >S Indicates the total number of calls (both voice and Multimedia Calls) that were answered after the Secondary Alert Threshold. Unanswered Help Request Report Clicking on the Unanswered Help Request Report button presents you with the Unanswered Help Request Report Period Selection page, shown below. This page allows you to specify the time period you wish the report to cover. The time period is specified by providing a From Date and From Time and a To Date and a To Time. The From Date specifies the first date you wish to have included in the report. Information from days before the From Date will not be included in the report. The From Time specifies the time on the From Date from which you wish to have data included in the report. Information from times before the From Time on the From Date will not be included in the report. The To Date specifies the last date you wish to have included in the report. Information from days after the To Date will not be included in the report. The To Time specifies the time on the To Date after which data will not be included in the report. Information from times after the To Time on the To Date will not be included in the report. Drop down menus allow you to choose dates and time values. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Reports 189 Figure 139 Unanswered Help Request Report Selection page Clicking on the Show Report button presents you with the report. This is shown below. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 190 Reports Figure 140 Unanswered Help Request Report Agent ID Indicates the Agent Log In ID (as specified in Call Center). Agent Name Indicates the Agent Name (as specified within Call Center). Time Indicates the time the help request was made Date Indicates the date when the help request was made. CLID Calling Line ID of the call the Agent was handling at the time of the help request. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Reports 191 Agent Average Report by Agent Clicking on the Agent Average Report by Agent button presents you with the Agent Average Report by Agent Skillsets page, shown below. Figure 141 Agent Average Report by Agent Skillset Selection Page This page allows you to select the Skillsets you wish to have included in the report, and to specify the time period you wish the report to cover. The time period is specified by providing a From Date and From Time and a To Date and a To Time. The From Date specifies the first date you wish to have included in the report. Information from days before the From Date will not be included in the report. The From Time specifies the time on the From Date from which you wish to have data included in the report. Information from times before the From Time on the From Date will not be included in the report. The To Date specifies the last date you wish to have included in the report. Information from days after the To Date will not be included in the report. The To Time specifies the time on the Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 192 Reports To Date after which data will not be included in the report. Information from times after the To Time on the To Date will not be included in the report. Drop down menus allow you to choose dates and time values. The Call Average Report Skillsets page allows you to select which Skillsets you wish to have included within the report. • • For a discussion of using Skillset Selection lists see page 60. For a discussion on using Favourites, see page 61. Our example User Mary Smith has used her Dev&Train Favourite to highlight and select the Development and Training Skillsets. Clicking on the Submit button generates the report. Figure 142 Agent Average Report by Agent For each Skillset, Agent by Agent the average durations of six Call Center statistics are displayed. For calls that have been transferred to the Agent the word Transferred will appear at Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Reports 193 the start of the line for that Agent. Likewise, if the Call Transaction was for an overflowed call the word Overflow will appear at the start of the line for that Agent. An Agent can therefore have up to three lines displayed for them, separating out the direct Call Center Call Transactions from the Transferred and Overflowed transactions. No. of Answered Call Transactions Indicates the number of Call Center transactions that this Agent has answered. Call Center Call Transactions Average Incoming Duration Indicates the average duration of the Call Center Call Transactions answered by this Agent. No. of Break Time Instances Indicates the number of times this Agent received Break Time from the Call Center. Average Break Time Duration Indicates the average duration of the Break Time periods this Agent received. No. Of Outgoing Calls Indicates the number of Outgoing Calls this Agent placed. This does not include internal calls, only calls that were made outside of the premises. Average Outgoing Calls Duration Indicates the average duration of the Outgoing Calls that this Agent made. Agent Activity Report by Skillset Clicking on the Agent Activity Report by Agent button presents you with the Agent Activity Report by Agent Skillsets page, shown below. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 194 Reports Figure 143 Agent Activity Report by Agent Skillset Selection Page This page allows you to select the Skillsets you wish to have included in the report, and to specify the time period you wish the report to cover. The time period is specified by providing a From Date and From Time and a To Date and a To Time. The From Date specifies the first date you wish to have included in the report. Information from days before the From Date will not be included in the report. The From Time specifies the time on the From Date from which you wish to have data included in the report. Information from times before the From Time on the From Date will not be included in the report. The To Date specifies the last date you wish to have included in the report. Information from days after the To Date will not be included in the report. The To Time specifies the time on the To Date after which data will not be included in the report. Information from times after the To Time on the To Date will not be included in the report. Drop down menus allow you to choose dates and time values. The Call Average Report Skillsets page allows you to select which Skillsets you wish to have included within the report. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Reports 195 • • For a discussion of using Skillset Selection lists see page 60. For a discussion on using Favourites, see page 61. Our example User Mary Smith has used her Dev&Train Favourite to highlight and select the Development and Training Skillsets. Clicking on the Submit button generates the report. Figure 144 Agent Activity Report by Agent For each Skillset in the report, Agent by Agent the average durations of five Call Center statistics are displayed. For calls that have been transferred to the Agent the word Transferred will appear at the start of the line for that Agent. Likewise, if the Call Transaction was for an overflowed call the word Overflow will appear at the start of the line for that Agent. An Agent can therefore have up to three lines displayed for them, separating out the direct Call Center Call Transactions from the Transferred and Overflowed transactions. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 196 Reports Logged In Time Indicates the total time that the Agent was logged in to the Call Center. This may be the sum of several (or many) instances, according to the duration covered by the report. No. Answered Call Center Transactions Indicates the number of Call Center transactions that this Agent has answered. Incoming Call Center Time Indicates the total duration of the Call Center Call Transactions answered by this Agent. No. of Break Time Instances Indicates the number of BreakTime instances this Agent received from the Call Center. Break Time Indicates the total duration of the Break Time periods this Agent received. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Reports Explained 197 Reports Explained 7 Answered Calls Report Figure 145 Answered Calls Report The Answered Call Report shows the total number of calls that were answered by the Skillsets included within the report. This report is calls based, and is not affected by call transactions. (Call Transactions are described on Page126.) Voice (PSTN) calls and Multimedia calls are listed separately and totalled for each Skillset, and for the report total. Both figures and the percentages are provided. The reports shows how long those calls that have been answered by your Call Center waited before they were answered. The breakdown is by the Answer Time Bins values (see Page 53). Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 198 Reports Explained Six time bins are specified, and a seventh is appended automatically, which captures all values higher than the sixth Time Bin. In this example, the time bins have been set in steps of 10 seconds, up to one minute. The seventh time bin will capture any call that was answered after waiting in excess of one minute. By looking at the figures of the answered Call Report the Supervisor of a Skillset can tell how long the calls that were answered by their Skillsets had to wait before they were answered. In this example the large data values in the first and last Time Bins indicate that incoming callers are, in general, answered within 10 seconds, or else they face a wait of over a minute. Very few calls that are not answered within 10 seconds are answered before a wait of at least a minute. This is probably a function of the average length of the calls and the number of callers the Call Center has. • The average length of the calls can be checked by looking at the Call Average Report (see Page 207). Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Reports Explained 199 Abandoned Call Report Figure 146 Abandoned Call Report The Abandoned Call Report shows the total number of calls that were abandoned (cleared down by the incoming caller) because they would not wait any longer, for each of the Skillsets included within the report. Voice (PSTN) calls and Multimedia calls are listed separately and totalled for each Skillset, and for the report total. Both figures and the percentages are provided. The reports shows how long those calls that did abandon waited before they were abandoned. The breakdown is by the Abandoned Time Bins values (see Page 53). Six time bins are specified, and a seventh is appended automatically, which captures all values higher than the sixth Time Bin. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 200 Reports Explained In this example, the time bins have been set in steps of 10 seconds, up to one minute. The seventh time bin will capture any call that abandoned after waiting in excess of one minute. Looking at the report we can see a descending profile from 10 seconds, through to the one minute, and a large value for the seventh Time Bin. This suggests that the callers to this particular Call Center fall into two main camps: those that realise they are going to be placed on hold, and who hang up straight away so that they can ring back later (those who hang up in less than 10 seconds) and those who once they have dialled in are going to hang on for a long time before they give up (those who abandoned after one minute). • • The identity of some of the abandoned callers may be held in the Abandoned Calling Line ID Report (see Page 201). The Call Profile Report (see Page 222) will allow you to see the spread of Abandoned Calls across the day. This can enable you to plan your staffing levels. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Reports Explained 201 Abandoned Calling Line ID Report Figure 147 Abandoned Calling Line ID Report The Abandoned Calling Line ID Report lists various items of information regarding the abandoned calls for the Skillsets included within the report. The data and the time at which each call abandoned is listed, together with the Calling Line Id of the call (when it is know) and the amount of time the caller waited before they abandoned. Some callers do not ‘advertise’ their calling ID when they make a call. In the instances where Nortel Networks Reporting for Call Center does not know the Calling Line ID, it displays the channel or line number on which the call arrived. IF required, this report can be used as the basis of a call-back policy in which abandoned callers are called as a courtesy follow-up. This could be done selectively, so that only the callers who held for the longest times before abandoning were called back (as they were the ones who were most determined to get through Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 202 Reports Explained and to make use of your services) or perhaps the report could be checked for the Calling Line ID of Gold or preferred customers (remember that you can search through on-screen reports, see Page 126). This report can also be used to see whether there is a spate of abandoned calls before or after the Call Center is closed, which can be used as an indicator of whether the Call Center should be staffed for a longer period, perhaps by a reduced skeleton staff populated on a rota basis. On the other hand, perhaps the early and late callers could be rung back to be advised of your opening hours. The Call Profile Report (see Page 222) will also indicate where the peaks of the Abandoned Calls fall throughout the day, but the Abandoned Calling Line ID report will also tell you who abandoned. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Reports Explained 203 Agent Capacity Report Figure 148 Agent Capacity Report The Agent Capacity Report shows how often, and for how long, the Call Center was working at its maximum Agent capacity. It shows the number of times that there were no Agents available to take a call (because they were already on a call, on an Outgoing Call, Not Ready, etc) and it also shows the total duration of all of these periods. That is, it details the instances and the duration of those instances when all Agents were occupied simultaneously with something which prevented them being presented with an incoming Call Center call. The Agent Capacity Report does not count instances when there were no Agents signed in, it only concerns itself with staffed periods. Note that if the Report includes more than one Skillset the Totals represent the cumulative amount of time for those periods in which all Agents were unavailable, across all of the Skillsets. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 204 Reports Explained This is not the same as summing all of the Skillset values. The Total figure in the report represents those times when portions of the individual Skillset maximum capacity periods overlapped with those from all other Skillsets. For example, the following section from a report shows two Skillsets: ID 1 3 Name Development Training Number of instances when No Agents were Available to Answer an Incoming Call Center Call Total 7 30 15 Total Time for All Those Instances Total 05:43 41:28 22:37 This shows that on 30 occasions all Agents in Development were unavailable for new calls, and the total time for these three periods adds up to 41:28. Likewise, Training had all of their Agents in use simultaneously on 15 separate times totalling 22:37 in total. However, the Totals show that there were only 7 occasions, which total to 5 minutes 43 seconds, when all of the Agents in Development and Training were in use at the same time. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Reports Explained 205 Help Request Report Figure 149 Help Request Report The Call Center Supervisory Help feature is intended for ‘emergency’ conditions when an Agent is on a call and urgently requires the help of a Supervisor without alerting the caller that a supervisor is being called in. It is not intended for routine consultations or when the Agent is not on a Call Center call. However, new Agents to your Call Center will most likely use the Help feature more frequently during their initial acclimatisation period. This report can be used to monitor the progress of new Agents, because as time goes by they should make fewer Help requests. It can also be used to determine if a particular customer has complex or troublesome requirements. As the Calling Line ID (where known) is displayed for each Help Request, any ‘difficult’ customers can be spotted. If a lot of Agents have all had to make Help Requests regarding a Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 206 Reports Explained particular caller, it might be decided that all Agents are informed to transfer that particular customer to the Supervisor as soon as the call is answered. If the Calling Line ID is not shown, the Line number is shown. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Reports Explained 207 Call Average Report Figure 150 Call Average Report This report can be used to determine the appropriate settings for the Primary and Secondary Alerts, or wallboard alarms, by looking at the Average Time to Answer and Average Time to Abandon figures. This report shows that the Average Time to Abandon is lower than the Average Time to Answer, so it would be appropriate to establish wallboard alarms when a call has waited (say) 15 seconds in the Skillset queue, to alert the Agents that a Call has been waiting in the Skillset queue for a period approaching the ‘danger time’ which in this Call Center is 26 seconds. The report can also be used to determine the Average Incoming Call Duration. This can then be used to determine an appropriate Agent Alarm for Incoming Calls, so that an Agent who has a call which lasts longer than the average duration is highlighted on the Agent Details Real Time Screen. The Average Incoming Call Duration can also be used to compare against the values in the Agent Average Report (see Page 191). Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 208 Reports Explained Agent Average Report Figure 151 Agent Average Report The Agent Average Report allows you to compare the activities of your Agents to one another. The Agents’ Average Incoming Call Transaction Duration is listed. Not that this report covers incoming call Transactions, not just Direct and Indirect Incoming Calls (see Page 126). If one Agent is taking much longer than other Agents on average to deal with his Incoming Calls this might indicate one of several things. Perhaps he is struggling and needs more training. Perhaps this Agent is better at a certain type of ‘difficult’ or complex call and the other Agents are transferring these harder calls to him because he is starting to become known as an ‘expert’ on them. Perhaps he is just being more attentive to the incoming callers. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Reports Explained 209 If an Agent is taking far less time to deal with their Incoming Calls, perhaps they are just fast, or they are being less attentive to the incoming caller, or perhaps they are transferring their calls to others to deal with. The Average Break Time duration allows you see which Agents are taking the full amount of Break Time and which Agents are not. If some Agents are on average taking 30 seconds and everyone else is taking 15 seconds, then perhaps the Break Time for everyone could be reduced to 20 seconds, and then after a period of acclimatisation, down to 15 seconds. ! Note if you request this report for (say) Skillset 1, you will receive a report listing all of the Agents who were logged into Skillset 1, including multi-Skillset Agents, and the report will include all of the activity of those Agents, irrespective of the Skillset of the call they handled. If this was not the case, and the report was limited to the Agent activity for the requested Skillset only, you would need to run the same report for each Skillset that each of the multi-Skillset Agents was logged into, to see a full picture of their activity. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 210 Reports Explained Agent Profile Report Figure 152 Agent Profile Report This report shows the actual figures and durations (not averages) for different activities that Agents have performed, for each log in session for the period of the report. Looking at the report above we can see that Alison was signed in for a period of 01:28 in the morning and again for a period of 04:55 in the afternoon. For each logged in session, the total time is then broken out into Available Time, Not Ready Time, Break Time, Incoming Time and Outgoing Time. The number of Outgoing and Incoming calls is also presented. We can see that Alison handled 50 Incoming Calls (19 in the morning and 31 in the afternoon). She spent a total of 2:18:43, doing so. This figure of 50 ties in with the figure of 50 on the Agent Average Report (see Page 191), from which we can see that for each of these 50 calls, Alison spent an Average of 02:46 talking to the incoming caller. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Reports Explained 211 ! Note if you request this report for (say) Skillset 1, you will receive a report listing all of the Agents who were logged into Skillset 1, including multi-Skillset Agents, and the report will include all of the activity of those Agents, irrespective of the Skillset of the call they handled. If this was not the case, and the report was limited to the Agent activity for the requested Skillset only, you would need to run the same report for each Skillset that each of the multi-Skillset Agents was logged into, to see a full picture of their activity. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 212 Reports Explained Agent Activity Report Figure 153 Agent Activity Report This report shows the durations for a range of activities that Agents have performed for the duration of the report. (This is a different list of activities than the list in the Agent Profile Report, see Page 210.) ! Note if you request this report for (say) Skillset 1, you will receive a report listing all of the Agents who were logged into Skillset 1, including multi-Skillset Agents, and the report will include all of the activity of those Agents, irrespective of the Skillset of the call they handled. If this was not the case, and the report was limited to the Agent activity for the requested Skillset only, you would need to run the same report for each Skillset that each of the multi-Skillset Agents was logged into, to see a full picture of their activity. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Reports Explained 213 Agent Audit Report Figure 154 Agent Audit Report This report provides a detailed breakdown of the various activities of an Agent, for the period of the report. Note that if the Agent is a multi-Skillset Agent, all of his activities will be included for all Skillsets into which he was signed, for the duration of the report. Also note that as this report is very detailed, it can grow VERY large VERY quickly. This report is best suited to on-screen, detailed examinations of short periods of a single Agent’s activity. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 214 Reports Explained Activity Code Report by Skillset Figure 155 Activity Code Report This report shows the Activity Codes which have been entered on calls for each Skillset included in the report. For each Skillset, the Activity Codes are presented in alphabetical order, with the average call duration time, the number of pegs and the actual accumulated time of all the calls that were associated with each Activity code. Activity Codes can be used to determine different things. If an Activity Code represented each magazine or publication in which advertisements had been placed and each incoming caller was asked to say where they saw the advertisement they were responding to, it is easy to build up a picture of which publications are the most effective vehicles for your advertisements. Activity Codes can be used to identify different types of call. For example, a Help Desk could have activity codes for different products that they support. It is then easy to see which products generate the most calls, or which product support calls have the highest average talk time. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Reports Explained 215 Activity Codes can be used to represent Agent activity as a result of a call, for example, Activity Codes could be established to represent Credit Account Application Letter Sent, or Catalog Posted, etc. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 216 Reports Explained Activity Code Report by Agent Figure 156 Agent Activity Code Report by Agent This report shows the Agents who have entered each Activity Code that has been entered on calls for the period of the report. For each Activity Codes, the Agents who have entered that Activity Code are listed, together with the average call duration time, the number of pegs each Agent has entered and the accumulated time of all the calls that were associated with each Activity code, per Agent. This is a quick and easy way of determining which Agents have handled certain calls, or performed certain call-related activities, such as performing a credit search, or requesting a catalogue dispatch. Activity Codes can be used to determine different things. If an Activity Code represented each magazine or publication in which advertisements had been placed and each incoming caller was asked to say where they saw the advertisement they were responding to, it is easy to build up a picture of which publications are the most effective vehicles for your advertisements. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Reports Explained 217 Activity Codes can be used to identify different types of call. For example, a Help Desk could have activity codes for different products that they support. It is then easy to see which products generate the most calls, or which product support calls have the highest average talk time. Activity Codes can be used to represent Agent activity as a result of a call, for example, Activity Codes could be established to represent Credit Account Application Letter Sent, or Catalog Posted, etc. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 218 Reports Explained Activity Code Report by # of Pegs Figure 157 Agent Activity Code Report by Number of Pegs This report shows the Activity Codes which have been entered on calls for each Skillset included in the report. For each Agent, the Activity Codes they have entered are listed, in descending order of use, together with the average call duration time, the number of pegs entered and the accumulated time of all the calls that were associated with each Activity code, per Agent. This is a quick and easy way of determining which activities or call types each Agent has spent most time on, or been most frequently involved with (which might not be the same thing). Activity Codes can be used to determine different things. If an Activity Code represented each magazine or publication in which advertisements had been placed and each incoming caller was asked to say where they saw the advertisement they were responding to, it is easy to build up a picture of which publications are the most effective vehicles for your advertisements. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Reports Explained 219 Activity Codes can be used to identify different types of call. For example, a Help Desk could have activity codes for different products that they support. It is then easy to see which products generate the most calls, or which product support calls have the highest average talk time. Activity Codes can be used to represent Agent activity as a result of a call, for example, Activity Codes could be established to represent Credit Account Application Letter Sent, or Catalog Posted, etc. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 220 Reports Explained Summary Report Figure 158 Summary Report The Summary report provides a quick one-report summation of the performance and activity of the Skillsets included in the report. A figure based and an average based table are provided, above a profile which spans the period of the report. For each unit of the profile the number of incoming calls, answered calls, abandoned calls, calls handled in another Skillset, Outgoing Calls and Unstaffed Calls are shown, together with the Grade of Service, expressed as a percentage, are shown. Six graphs are included within the Summary Report, these are shown below. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Reports Explained 221 Figure 159 Summary Report Graphs Page Each of the graphs shows a bar chart profile across the period of the report. This allows correlations of data to be highlighted, which can then be investigated using the other more detailed reports. This report would tend to indicate that there should be some investigation into why the two highest numbers of Outgoing Calls are made at the same time as the two highest numbers of Abandoned Calls, which occurs at the same time. Presenting the information in this fashion makes such anomalies easy to spot, allowing the Supervisor to then look further into the matter. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 222 Reports Explained Call Profile Report Figure 160 Call Profile Report This report shows a profile across the period of the report which shows the numbers of calls presented to the Skillsets in the report, and the number answered, abandoned, Answered by Agents, Voice Mail, operator, Overflow Agents, Non-Agents and Other Skillsets. It also presents the Grade of Service expressed as a percentage. This report can be used to look at the numbers and the ‘fate’ of calls that come in across the profile of the report. How many calls come in the various time slots across the report? Are they Answered, if so, where are they answered, buy the Agents in the Skillset or by something else? These questions can be answered by looking at the Call profile Report. The Call profile Report can also be used to help determine such things as staffing levels. Doing a profile of a week may show a peak of calls on a Wednesday. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Reports Explained 223 Generating a Call Profile report for several weeks prior to the first report will identify whether this is a general trend in an ‘average’ week. Perhaps you need to have a higher staff availability on Wednesdays, for some reason? Perhaps an advertisement is placed weekly in a magazine that comes out on Wednesdays? If Activity Codes are used to track the publication callers are responding to the advertisement from, this could be established quite easily. Activity Codes could also be used to determine whether the observed peak of calls on each Wednesday were calls of the same type on all Wednesdays or whether they were different and Wednesday happened to be a busy day for some other reason. The effectiveness (or otherwise) of a marketing campaign could be seen by running a Call Profile report for the same period for a number of previous year and then running another report for the year with the marketing campaign and comparing the figures, which will automatically be seasonally-adjusted as the reports cover the same period. Figure 161 Call Profile Report Graph Page Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 224 Reports Explained Incoming Call Report Figure 162 Incoming Call Report The Incoming Call Report relates to Incoming Direct and Indirect Calls, not Call Transactions (see Page 126). This report provides a consolidated one line summary of the call traffic into the Skillsets included in the report, and the call handling of that traffic. This report makes it easy to find the answers to such questions as how many calls (Direct and Indirect) were presented to the Skillsets, and how many were Answered and Abandoned. Of those that were Answered, where were they answered, and who by? How many calls were answered before the Primary Alert (<P), how many were answered after the Primary Alert but before the Secondary Alert (>P) and how many were answered beyond the Secondary Alert (>S)? Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Reports Explained 225 Unanswered Help Request Report Figure 163 Help Request Unanswered Report This report shows the Help Requests that were made by Agents, but which were not serviced by a Supervisor. This report should be read in conjunction with the Help request Report (see Page 205) to establish the total number of Help Requests and Agent is making. This report can also be used to determine if a Supervisor is refusing too many Help Requests. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 226 Reports Explained Agent Average Report by Agent Figure 164 Agent Average Report by Agent This report allows the work performed by each Agent in each Skillset they have logged into to be reviewed. A report may include a single Skillset or multiple Skillsets. If an Agent has been logged into more than one Skillset and those Skillsets were selected to be included in the Report then the activities of the Agent are segregated so that the work in Skillset is separately displayed. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Reports Explained 227 Agent Activity Report by Skillset Figure 165 Agent Activity Report by Skillset This report allows the work in each Skillset to be reviewed. All of the Agents who have logged into those Skillsets included in the report are reported on. Only the activity directly related to the appropriate Skillsets is displayed for each Skillsets. In the example above, Agent Zoe has been logged into Skillset 1 and Skillset 3, and so the report breaks out her activity for each of these Skillsets, and she appears in the report under both the Skillset 1 and the Skillset 3 categories. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 228 Upgrading to Reporting for Call Center Upgrading to Reporting for Call Center 8 Introduction This section answers the questions that need to be asked during the upgrade of an existing installation of Nortel networks Call Center Reporting version 2.5, 3.0 or 3.5 to Nortel Networks Reporting for Call Center. What Do I have to Install? Nortel Networks Reporting for Call Center has a single software installation onto one PC. This PC is the Web Host PC, which acts in a similar fashion to the ‘Master’ PC in the old Nortel Networks Call Center Reporting 2.5, 3.0 and 3.5 streams. The Web Host PC stores the historical statistical databases. It communicates with the Call Center in order to obtain the historical statistical information and Real Time screen information. The wallboards are also driven from the Web Host PC. See the chapter Installation on page 8. Can the old Master PC be used as the Web Host PC? If the PC hardware and Operating System meet the minimum specifications, then the answer is ‘Yes’. See the question ‘Can the new software co-reside with the old software’, below. See the Minimum Hardware Requirements on page 6, and the Operating System Compatibility on page 7. Why is there No ‘Multiple Client’ software to install? In the Call Center Reporting 2.5, 3.0 and 3.5 streams the customer had to install ‘Multiple Client’ software onto other PCs in order to view the Real Time screens or Reports from those PCs. With Nortel Networks Reporting for Call Center the users of those other PCs use Internet Explorer to browse back to the Web Host PC in order to access the Real Time screens and Reports. There is no ‘Client’ software required for the Users on those other PCs. Do I have to remove the old Nortel Networks Call Center Reporting 2.5, 3.0 or 3.5 software? No, see the question ‘Can the new software co-reside with the old software’, below. Can the new software co-reside with the old software? None of the Nortel Networks Call Center Reporting 2.5, 3.0 or 3.5 software is required for the operation of the new Nortel Networks Reporting for Call Center software. However, the customer may wish to retain the Nortel Networks Call Center Reporting 2.5, 3.0 or 3.5 software in order to allow them to review the historical reports that were gathered with their old system. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Upgrading to Reporting for Call Center 229 Leaving the Nortel Networks Call Center Reporting 2.5, 3.0 or 3.5 Master or Multiple Client software on the PC which is going to be used as the Web Host PC will not affect the operation of Nortel Networks Reporting for Call Center. The two different applications can co-reside on the same PC with no interaction. That is, installing Nortel Networks Reporting for Call Center onto a PC on which Nortel Networks Call Center Reporting 2.5, 3.0 or 3.5 is already installed will not cause either of the applications a problem in running. Note however, that if the Nortel Networks Call Center Reporting 2.5, 3.0 or 3.5 software was configured to drive any IP wallboards that are going to be driven by Nortel Networks Reporting for Call Center, remember to take them out of the Nortel Networks Call Center Reporting 2.5, 3.0 or 3.5 configurations, otherwise both sets of software will try to drive the wallboards, which will result in the wallboard display flashing back and forth between the two sets of data being sent to it by the two different applications. Note also that the hardware used as the Master PC for the Nortel Networks Call Center Reporting 2.5, 3.0 or 3.5 software might not by of sufficient specification to support the Nortel Networks Reporting for Call Center software. See the list of Minimum Hardware Requirements on page 6, and the Operating System Compatibility on page 7. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 230 Troubleshooting Reporting for Call Center Troubleshooting Reporting for Call Center 9 Slow Updates on Real Time Screen The real Time screens should be updated approximately every 3 seconds. If they seem to be slow or sluggish, the following points should be checked. Web Host PC Requires a Host File entry Check with your Network Administrator to add an entry in the Web Host PC Host file. This is a Windows system file and is usually located in the \Windows\System32\drivers\etc folder of the Web Host PC (this may be called the \Winnt\System32\drivers\etc folder). You must enter the IP Address and the network name (machine name) of the Business Communications Manager to this file. Separate the two items by using the Tab key. An example Host file is shown below. # # # # # # # # # # # # # # # # # Copyright (c) 1993-1999 Microsoft Corp. This is a sample HOSTS file used by Microsoft TCP/IP for Windows. This file contains the mappings of IP addresses to host names. Each entry should be kept on an individual line. The IP address should be placed in the first column followed by the corresponding host name. The IP address and the host name should be separated by at least one space. Additionally, comments (such as these) may be inserted on individual lines or following the machine name denoted by a '#' symbol. For example: 102.54.94.97 38.25.63.10 127.0.0.1 10.1.1.105 rhino.acme.com x.acme.com # source server # x client host Localhost BCMMachineName Figure 166 Example Host File Anti-Virus Software Slowing Down the File System Some Anti-Virus software packages have been seen to cause such a significant slow down on the file system of the Web Host PC that the Real Time screens have trouble processing all of the XML data they receive from the Call Center in time to refresh the Real Time data in a timely fashion. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Troubleshooting Reporting for Call Center 231 Norton Anti-Virus is one anti-virus package known to cause this symptom. By Un-checking the “Enable File System Real Time Protection” option in Norton Anti-Virus the operation of the Real Time screens are no longer restricted and cal operate in their usual way. To do this, right click on the Norton Anti-Virus icon in the system tray. If there is a tick by it, select “Enable File System Real Time Protection” to remove the tick. Alternatively, you can try deactivating the Nortel Networks Reporting for Call Center diagnostic logging (if it is activated), see Page 43. Anti-Virus packages vary in their implementations and in the granularity with which you can adjust their operational parameters. Typically, however, the settings which you can adjust that would make the Real Time Screens appear sluggish in updating are the real time file scanning settings. Note: ‘real time’ in this context means that the Anti-Virus software scans the files on your computer constantly – it does not refer to the Reporting for Call Center Real Time screens. It is just a coincidence that both applications have features that have the words ‘real time’ in their title. • • • Some Anti-Virus packages allow you to specify files with certain extensions which are to be ignored during virus scans. If this is possible with your Anti-Virus software, instruct it to ignore files with .log extensions. Some Anti-Virus packages allow you to specify locations on your hard disk which are to be ignored during virus scans. If this is possible with your Anti-Virus software, instruct it to ignore the location of the Reporting for Call Center log files. By default this is \Program Files\Nortel Networks\Reporting for Call Center\Logs. Some Anti-Virus packages allow you to disable or fine tune the real time scanning action of files, and to isolate which types of file modification will trigger a re-scan (create a file, modify a file, write to a file, etc). Cannot Access the Login Page This problem has been seen when the Web Host PC has Norton Anti-Virus running. One setting of Norton Anti-Virus (Script Blocking) prevents Nortel Networks Reporting for Call Center from running normal operations. This option should be disabled in the anti-virus configuration screen on the Web Host PC only. Turning off script blocking in Norton Anti-Virus 2001 To disable Norton Anti-Virus 2001 Script Blocking: 1. Start Norton Anti-Virus. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 232 Troubleshooting Reporting for Call Center 2. Click Options. If a menu appears when you click Options, then click Norton Anti-Virus. The Options for Norton Anti-Virus dialog box appears. Figure 167 Norton Anti-Virus Options Screen 3. Click Script Blocking. 4. Uncheck "Enable Script Blocking (recommended)." 5. Click OK. NOTE: Script Blocking is a feature of Norton Anti-Virus 2001 that was added to as a part of a program update. If Script Blocking does not appear in Options, then the program update is not installed. To install the Norton Anti-Virus program update, run LiveUpdate, and download all program updates. Restart the computer when prompted. Run LiveUpdate until you are told that there are no more updates available. Turning off script blocking in Norton Anti-Virus 2002 or 2003 To disable Norton Anti-Virus Script Blocking: 1. Start Norton Anti-Virus. 2. Click Options. If a menu appears when you click Options, then click Norton Anti-Virus. The Norton Anti-Virus Options dialog box appears. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Troubleshooting Reporting for Call Center 233 Figure 168 Norton Anti-Virus Options Dialog 3. Click Script Blocking. 4. Clear the Enable Script Blocking check box(recommended). 5. Click OK. Restart the computer if prompted to do so. Changing Agent Names If an Agent changes their name, for example if they marry and take a new surname, or if an Agent leaves and their Call Center Log In ID is allocated to another person, this will affect the way in which Reporting for Call Center displays information for the Agent in the reports. The reports will distinguish between the two identities associated with the single Call Center Log In ID as follows. • • • The Agent Activity Report will list each Agent separately. The Agent Audit Report will consider that Call Center Log In ID to be the same person and will show all activity that the Agent with that ID has performed, irrespective of the Agent name in the User Admin screens. In effect, for the same period, reporting on the first Agent name will yield the same information as a report on the second Agent name. The Agent Average Report will reference the first Agent name only. If both Agent names refer to the same person (for example, it is the same person but they have taken a new surname because they have married), these differences do not matter. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 234 Troubleshooting Reporting for Call Center However, if the name change is because of an actual change of personnel, then it is easier to isolate the activities of the two Agents in the reports if the new Agent is allocated a distinct Call Center Log In ID, and the old Log In ID is no longer used. Virtual Folders Not Created in Internet Information Services Reporting for Call Center relies upon some Virtual Folders which are created during the installation of Reporting for Call Center on the Web Host PC. If these Virtual Folders are ever inadvertently removed or altered, or if they are not created during the installation, you will see the following error page. Figure 169 Page Cannot Be Displayed Error Message If you see this, please try the following steps. 1. Click Start, Run and enter the pathway to the file called Create.bat in the RunOnce folder. The RunOnce folder is in the Reporting for Call Center folder. If you installed Reporting for Call Center in the default location the path to this file will be \Program Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Troubleshooting Reporting for Call Center 235 Files\Nortel Networks\Reporting for Call Center\RunOnce\Create.bat on the drive on which you installed Reporting for Call Center. 2. When you have located this file, double-click on it to launch it. You will see a Command Prompt window (DOS Window) open and then close. 3. Try accessing the http://localhost/rcc/main/login.asp page one more. Accessing Networked Printers From the Web Host PC In order for the Web Host PC to contact and utilize network printers, you must have a User logged into Windows on the Web Host PC. This means that if you wish to run Scheduled Prints out of hours, you must have a User logged in to the Web Host PC. Multiple Network Cards in the Web Host PC or an Agent PC Running Nortel Networks Reporting for Call Center is not supported on Web Host PC that has more than one network interface card installed. Currently there is no way to select which network card the Web Host PC Wallboard Driver binds to. If the wallboard driver binds to the wrong network card it will not be able to drive your wallboards and/or ipView SoftBoards. The workaround is to restart the Web Host PC until the wallboard driver binds to the correct network card, and then do not power off your Web Host PC. Currently there is no way to select which network card the ipView SoftBoard binds to. If the ipView SoftBoard binds to the wrong network card it will not be able to receive data from the Web Host PC. The workaround is to close down and re-start ipView until it binds to the desired network card. Note: If you right-click on the ipView icon in the system tray, and select About ipView, the About window will show you the IP Address that ipView has bound to, as shown below. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 236 Troubleshooting Reporting for Call Center Figure 170 ipView Help Window ipView SoftBoard and Wallboard Summaries Note that the Wallboard Summaries are sent to the wallboards on the hour, according to the time of the Web Host PC clock. The regular hourly and daily statistics that are sent to the wallboard are governed by the Call Center platform clock. The hourly statistics are reset to 0 on the hour, according to the clock in the Call Center platform. If the clock in the Web Host PC is set to a different time than the clock in the Call Center platform, the hourly Summaries will not be synchronised with the hourly reset of the regular statistics. To ensure that the wallboard summaries are in time with the hourly resets of the regular wallboard statistics, ensure that your PC and Call Center platform times are the same. Crystal Reports ActiveX Report Viewer The first time that reports are viewed on a client PC (that is, some PC other than the Web Host Viewer) an ActiveX viewer is installed onto the Client PC, from the Web Host PC. If this does not automatically happen, you will not be able to view reports (you will see the Report Viewer window with a red X in the top left corner). If you see this you can start the installation process manually. On the Web Host PC in \Program Files\Common Files\Crystal Decisions\2.0\crystalreportviewers\ActiveXViewer\en there is a file called npviewer.exe. This file should be copied to the Client PC and executed there. This will install the ActiveX viewer. Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Troubleshooting Reporting for Call Center 237 Real Time Screens on Client PCs The first time that the Real Time screens are viewed on a client PC (that is, some PC other than the Web Host Viewer) a Java Run Time Module should be automatically installed onto the Client PC, from the Web Host PC. If this does not automatically happen, you will not be able to view the Real Time screens. To overcome this you can start the installation process manually. On the Web Host PC in C:\Program Files\Nortel Networks\Reporting for Call Center\Javadist there is a file called j2re-1_4_2_03-windows-i586-p.exe. This file should be copied to the Client PC and executed there. This will install the Java Run Time Module. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 238 Glossary Glossary 10 Abandoned Calls........ Abandoned Calls are calls that ring in to the system and the incoming caller clears down the call because they do not wish to wait any longer before they are answered. These calls have not been handled by humans or by voice mail. Abandon Time Bins ... A series of six time steps used in the statistical analysis of Abandoned Calls. Nortel Networks Reporting for Call Center will provide statistical reports on the percentage of incoming calls abandoned within each of the periods specified in the Abandoned Time Bins. A seventh period is also used in the reports, which gathers information on all calls which abandoned after the period specified by the sixth Abandoned Time Bin. Administrator ............. A Nortel Networks Reporting for Call Center User who has been awarded Administration rights. These Users can configure core elements of Nortel Networks Reporting for Call Center that regular Users can not, and they can perform such actions as creating other Users. Alarm Threshold ........ Alarms may be set to trigger an alert on the wallboards, to inform your Agents of some event or circumstance. The value that a parameter must reach, match or exceed to trigger an Alarm is the Alarm Threshold. All Calls Held ............ If an Agent has placed all of their calls on hold, so that they have no active calls, they will be shown in Magenta in the Real Time screens. Answered Time Bins.. A series of six time steps used in the statistical analysis of Answered Calls. Nortel Networks Reporting for Call Center will provide statistical reports on the percentage of incoming calls answered within each of the periods specified in the Answered Time Bins. A seventh period is also used in the reports, which gathers information on all calls that were answered after the period specified by the sixth Answered Time Bin. Available State ........... The Agent is ready to take Incoming Calls. The Available State is shown as Blue in the Real Time Screens. Break Time................. The period allocated to Agents following clear down of an Incoming Call Center Call (also known as Wrap Up and Post Call Completion). Break Time is displayed in the Real Time Screens as Dark Green. Calls Answered .......... ‘Answered’ means the Call was not abandoned, and it did not require the involvement of another Skillset in the handling of the call Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Glossary 239 Calls Presented........... The counts all of the calls that were presented to a Skillset, both Direct (a ‘regular Call Center call’ delivered straight into the Skillset,) and Indirect, which means the Call arrived in the Skillset in some other way. Direct Call.................. From the point of view of any given Skillset, Direct Calls are calls that were presented directly to that Skillset. That is, the incoming caller was handled by the Call Routing and was presented by the Call Routing directly to the Skillset in question. Calls Handled In Another Skillset ......... Calls that have left a Skillset and entered another Skillset because of an Overflow Rule or any other Routing Condition or Step. The fate of these calls is then recorded in the reports for the Skillset they have moved to – not in the Skillset they leave. Indirect Call ............... From the point of view of any given Skillset, Indirect Calls arrived in the Skillset after being handled by the Call Routing or Agents of another Skillet. For example, they may have overflowing from another Skillset or may have been manually transferred to the Skillset queue by an Agent from another Skillset. Any way a Call can arrive into a Skillset other than being a regular Call Center Call presented Directly to the Skillset (as described above) is counted as an Indirect Call. Whether the call overflowed to the Skillset in question, or was moved to the Skillset by the Move to Queue Call Routing step, or whether it was manually transferred to the Skillset Control Dn, it is counted as an Indirect Call. Grade of Service ........ The Grade of Service is a figure that is used to represent the level of service provided to incoming callers, based upon Call Center response times. It is calculated as follows: Presented = Total Number of Direct Call transactions Presented to the Skillset Abandoned = Calls which Abandoned >Secondary = Calls transactions answered after the Secondary Alert G of S% = Presented - Abandoned – >Secondary x 100 Presented Incoming State ........... The Agent is engaged on an Incoming Call Center Call, either a PSTN or a Multimedia call. The Incoming State is shown as Green in the Real Time Screens. If an Agent has been on an Incoming Call in excess of the Incoming Call Duration Threshold their timer will be displayed against a Red background. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 240 Glossary Multimedia Call ......... A call generated and conducted through the use of Nortel Networks Multimedia Call Center. A call which may involve a Follow-me browser session, a Chat session or was initiated by a caller clicking a button on a Web Page. Non-Call Center Call State .................... Grey is used for non-Call Center calls. Not Ready State .......... Either the Agent has invoked the Make Not Ready feature to indicate they are not Available to take calls or the Call Center has placed them in the Not Ready state because a call was unanswered at their handset or the Agent is active on an internal call. The Not Ready State is shown as Dark Grey in the Real Time Screens. If an Agent has been Not Ready in excess of the Not Ready Duration Threshold their timer will be displayed against a Red background. Outgoing State ........... The Agent is engaged on an Outgoing Call. The Outgoing State is shown as Yellow in the Real Time Screens. If an Agent has been on an Outgoing Call in excess of the Outgoing Call Duration Threshold their timer will be displayed against a Red background. PSTN Call .................. Private Switched Telephone Network Call – a ‘regular’ voice call. Real Time................... Information is available that displays the current states of Skillset Calls and Agents. This information is refreshed approximately every 3 seconds. These displays are called the Real Time Screens. Information can also be displayed on hardware and software TCP/IP enabled wallboards, to provide Real Time information to the Call Center Agents. Stat Time Bins............ A collective term for the Abandoned Time Bins and the Answered Time Bins. Supervisor Monitoring If a Supervisor is monitoring an Agent the Supervisor is displayed in the Real Time in Brown, and the Status column will say ‘Monitoring’. TCP/IP........................ Transmission Control Protocol/Internet Protocol: A protocol developed by the US Department of Defense for communications between computers. It has become the de facto standard for data transmission over networks, including the Internet. TCP and IP are transport and address protocols; TCP is used to establish a connection for data transmission, and IP defines the method for sending the data in packets. Title ............................ A string of text displayed on the top line of a wallboard. This restricts the wallboard to being able to display 3 parameters only. User ............................ A User is a person who has been allocated a Username and Password to allow them to use Nortel Networks Reporting for Call Center. Users can configure some elements of their usage of Nortel Networks Reporting Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Glossary 241 for Call Center, but they do not have the same scope for configuration as an Administrator. Unstaffed Calls........... Calls that were presented to the Skillset when there were no Agents logged In to handle those calls. Wallboard................... A device that is used to display Call Center statistics and messages to the Agents and other Call Center staff. Nortel Networks Reporting for Call Center TCP/IP enabled hardware WallBoards and SoftBoards from the ipView range of wallboards. Issue 02 (05) Reporting for Call Center Set Up and Operations Guide 242 References References 1 11 Software Keycode Installation Guide Reporting for Call Center Set Up and Operations Guide Issue 02 (05) Index 243 11 Index A B Abandon Time Bins, 50, 238 Abandoned, 50, 53, 59, 69, 77, 87, 91, 98, 131, 134, 135, 136, 137, 138, 175, 176, 177, 180, 182, 185, 187, 199, 200, 201, 202, 221, 224, 238, 239, 240 Abandoned Call, 50, 59, 69, 77, 131, 134, 135, 136, 137, 138, 175, 176, 177, 187, 199, 200, 201, 202, 221, 238 Abandoned Call Report, 134, 135, 136, 199 Abandoned Calling Line ID Report, 137, 138, 200, 201 Abandoned Time Bins, 50, 136, 199, 238, 240 Activity Code, 54, 63, 71, 79, 161, 162, 163, 164, 165, 166, 167, 168, 169, 170, 171, 172, 214, 215, 216, 217, 218, 219, 223 Activity Code Report by # of Pegs, 54, 63, 71, 79, 169, 170, 171, 218 Activity Code Report by Agent, 54, 63, 71, 79, 165, 166, 167, 168, 172, 216, 218 Activity Code Report by Skillset, 54, 63, 71, 79, 161, 162, 163, 164, 214 Add Alarm, 112, 113 Add Message, 108, 109, 110 Add User, 33, 34, 36, 37, 97 Add Wallboard, 102, 103, 104, 106 Administration Menu, 25, 26, 30, 31, 32 Administrator, 2, 4, 5, 10, 11, 14, 24, 25, 26, 27, 31, 32, 34, 41, 48, 49, 52, 97, 100, 104, 122, 230, 238, 241 Adobe, 129 Agent, 32, 54, 63, 71, 79, 85, 86, 88, 91, 92, 93, 94, 95, 96, 97, 103, 125, 126, 131, 134, 136, 139, 140, 141, 143, 144, 146, 147, 148, 149, 150, 151, 152, 153, 154, 155, 156, 157, 158, 159, 160, 165, 166, 167, 168, 172, 175, 181, 185, 186, 190, 191, 192, 193, 194, 195, 196, 197, 199, 203, 205, 207, 208, 209, 210, 211, 212, 213, 215, 216, 217, 218, 219, 225, 226, 227, 233, 234, 235, 238, 239, 240 Agent Activity Report, 153, 154, 155, 193, 194, 195, 212, 227, 233 Agent Alarms, 94, 95, 96, 97 Agent Audit Report, 54, 63, 71, 79, 156, 157, 160, 213, 233 Agent Average Report, 146, 147, 149, 191, 192, 193, 194, 195, 207, 208, 210, 226, 233 Agent Capacity Report, 139, 140, 141, 203 Agent Detail, 91, 92, 207 Agent Profile Report, 149, 150, 152, 210, 212 Alarm Messages, 99 Alarm Periods, 115, 117 Alarm Thresholds, 99 Answer Time Bins, 50, 197 Answered Call, 50, 59, 69, 77, 94, 100, 132, 133, 134, 175, 176, 177, 187, 193, 196, 197, 238 Answered Calls Report, 132, 133, 134, 197 Anti-Virus Software, 230, 231, 232, 233 Assigned Skillsets, 5, 39, 40 Available, 86, 93, 96, 98, 129, 152, 159, 204, 210, 238, 240 Brazilian Portuguese, 5 Break Time, 86, 92, 93, 149, 152, 156, 193, 196, 209, 210, 238 Browser, 12, 30 Business Communications Manager, 4, 12, 21, 27, 230 Buzzer, 104 Issue 02 (05) C Call Average Report, 141, 144, 145, 192, 194, 198, 207 Call Center, 4, 6, 8, 10, 11, 21, 26, 27, 28, 29, 30, 33, 39, 43, 58, 68, 76, 86, 87, 90, 91, 92, 93, 94, 99, 116, 127, 132, 143, 144, 156, 158, 160, 163, 167, 171, 193, 196, 198, 202, 203, 228, 230, 236, 240 Call Center Connection, 1, 4, 26, 27, 29, 30 Call Center platform, 4 Call Center, the, 4 Call Detail, 89, 90 Call Profile Report, 178, 179, 180, 181, 182, 200, 202, 222, 223 Call Profile Report Graph, 181, 182, 223 Call Routing, 125, 126, 176, 178, 184, 185, 186, 239 Call Transactions, 126, 146, 149, 175, 176, 193, 195, 196, 197, 224 CallPilot, 1, 4, 13, 21, 27, 28, 39 Canadian French, 5 CCRS, 1, 28 Chat session, 93, 96, 240 Company Details, 44, 45, 127 Control key (CTRL), 40, 61, 158, 163, 167, 171 Control Panel, 8, 11 D Daily Schedules, 54, 55, 56, 57, 58, 59, 60, 61, 62, 63, 64, 65, 71 Danish, 5 Direct Call, 125, 126, 176, 184, 239 Dutch, 5 E Edit Parameters, 106, 107 Edit User, 37 Edit Wallboard, 105, 106 Excel, 129 Export, 127, 129 F Favourite, 61, 62, 70, 78, 84, 95, 123, 132, 136, 138, 140, 145, 155, 158, 162, 166, 170, 174, 179, 184, 192, 195 Favourites, 5, 23, 47, 61, 62, 70, 78, 84, 95, 122, 123, 132, 135, 136, 138, 140, 145, 155, 158, 162, 166, 170, 174, 179, 184, 192, 195 Reporting for Call Center Set Up and Operations Guide 244 Index Follow-me, 93, 240 French, 5 Multiple Client, 228, 229 MySQL database, 6, 8, 19 G German, 5 Grade of Service, 91, 98, 100, 114, 175, 176, 178, 181, 220, 222, 239 Graph, 181, 182, 186, 187, 223 H Help Request Report, 141, 142, 143, 188, 189, 190, 191, 193, 205, 225, 226, 227 Help Request Unanswered Report, 188, 190, 191, 193, 225, 226, 227 Hide Agent Summary, 88 Hide Skillset Call Summary, 88 I IBM, 6 Incoming Call Report, 182, 183, 184, 186, 187, 224 Incoming Call Report Graph, 186, 187 Indirect Call, 125, 126, 146, 176, 185, 224, 239 In-Progress Calls, 127 Install Clients page, 12 Installation, 1, 2, 8, 10, 11, 12, 13, 19, 20, 228, 242 InstallShield, 13, 14, 15 Instant Messages, 100, 122, 123, 124 Intel, 6 Internet Explorer, 4, 6, 7, 8, 9, 12, 23, 47, 228 Internet Information Services, 7, 10, 30, 234 Introduction, 2, 4, 8, 97, 125, 228 IP Address, 12, 23, 26, 27, 28, 47, 103, 230, 235 ipView Softboard, 98, 99, 103, 235, 236, 241 Italian, 5 L Language Support, 4 Latin American Spanish, 5 License Agreement, 16, 17, 21 Localhost, 230 Log In, 14, 23, 24, 47, 110, 120, 152, 156, 160, 190, 233, 234 Logging Menu, 42, 43, 44 Longest Waiting Time, 87, 91 M Maintenance, 41 Master PC, 228, 229 Microprocessor, 6 Microsoft, 7, 10, 21, 30, 129, 230 Minimum PC Requirements, 6 Monitoring, 93, 156, 240 Monthly Schedules, 54, 74, 75, 76, 77, 78, 79, 80, 81, 82 Mouse, 7 Multimedia Call, 89, 90, 96, 125, 180, 181, 184, 185, 186, 187, 188, 240 Reporting for Call Center Set Up and Operations Guide N Network Name, 26, 27, 103 Non-Agent, 181, 185, 222 Nortel Networks Call Center Reporting, 2, 4, 8, 11, 21, 228, 229 Nortel Networks Reporting for Call Center, 2, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 18, 19, 20, 23, 27, 29, 31, 32, 33, 34, 39, 41, 42, 43, 45, 47, 48, 49, 50, 53, 54, 62, 86, 94, 95, 98, 99, 100, 103, 104, 113, 114, 124, 125, 130, 132, 141, 201, 228, 229, 230, 231, 233, 234, 235, 237, 238, 240, 241 North American English, 5 Norwegian, 5 Not Ready, 86, 93, 96, 98, 99, 109, 110, 115, 152, 156, 203, 210, 240 O On Call Center Calls, 86 On Internal Calls, 86 On Non-Call Center Calls, 86 On Outgoing Calls, 86 Operating System, 7, 228, 229 Operator, 181, 185 Overflow, 87, 91, 176, 181, 185, 193, 195, 222, 239 Overflow Table, 185 P Page Range, 130 Parameters, 104, 105, 106, 107, 115 Password, 24, 25, 37, 38, 48, 240 Primary Alert, 87, 90, 186, 224 Print Schedules, 54, 55 Printer, 128, 130 Printing a Report, 128 R Real Time screens, 4, 5, 6, 8, 27, 32, 38, 41, 83, 84, 85, 86, 88, 89, 90, 91, 92, 93, 94, 207, 228, 230, 231, 237, 238, 239, 240 Real Time Summary, 83, 84, 85, 86 Report Headers, 127 Report Magnification, 130 Report Periods, 125 Report Viewer, 127, 128, 236 Reset Password, 37, 38 Rich Text Format, 129 Routing Table, 186 S Scheduled Messages, 100 Scrolling Messages, 98 Secondary Alert, 87, 90, 186, 188, 207, 224, 239 Skillset Assignment, 38, 41 Issue 02 (05) Index 245 Skillset selection, 52, 62, 95 Spanish, 5 Statistical Data, 6, 7 Summary Messages, 100 Summary Report, 173, 174, 175, 176, 177, 220, 221 Summary Report Graph, 176, 177, 221 SVGA, 7 Swedish, 5 System Admin Settings, 31 System Administration Menu, 30, 31, 32 System Status, 41, 42 100, 102, 104, 109, 110, 115, 120, 122, 123, 125, 132, 136, 138, 140, 145, 155, 158, 162, 166, 170, 174, 179, 184, 192, 195, 228, 233, 235, 238, 240 User Admin, 31, 32, 33, 36, 37, 38, 233 V Voice (PSTN) Call, 89, 90, 197, 199, 239, 240 Voice Mail, 181, 185, 222 Voice PSTN Call, 89, 90, 93, 125, 134, 136, 146, 180, 181, 184, 185, 186, 187, 197, 199, 239, 240 T W TCP/IP, 7, 11, 12, 230, 240, 241 Time Bins, 50, 51, 52, 53, 54, 134, 136, 197, 198, 199, 238, 240 Time Bins Setup, 50, 51 Title, 104, 127, 240 Troubleshooting, 1, 230 Wallboard, 97, 100, 101, 102, 103, 104, 105, 106, 107, 108, 119, 122, 235, 236, 241 Wallboard Assignment, 101, 102 Web Based User Interface, 4 Web Host PC, 4, 6, 8, 10, 11, 13, 14, 20, 23, 28, 29, 30, 47, 54, 58, 68, 76, 228, 229, 230, 231, 234, 235, 236, 237 Web page, 4, 6, 30, 34, 240 Weekly Schedules, 65, 66, 67, 68, 69, 70, 71, 72, 73, 74 Windows, 1, 7, 8, 10, 11, 12, 13, 14, 130, 230, 235 Windows 2000, 7, 12 Windows 95, 107, 115, 131, 134, 137, 139 Windows Networking Component, 11 Windows NT 4, 7 Windows XP, 7, 12 With All Calls Held, 86 Word, 129 U Unanswered Help Request Report, 225 Unified Manager, 12 United Kingdom English, 5 Unread Skillset Messages, 87 Upgrading, 2, 8, 228 URL, 23, 47 User, 2, 3, 4, 5, 6, 14, 17, 31, 32, 33, 34, 36, 37, 38, 39, 40, 41, 46, 49, 50, 52, 58, 68, 70, 76, 78, 84, 95, 96, 97, 99, Issue 02 (05) Reporting for Call Center Set Up and Operations Guide