Download GSS SDSP 908 video switch
Transcript
I N STAL L ATIO N E QUIPM EN T P ROGRAMME 2012/2013 INDEX 2 Editorial 3 Standard Multiswitches for Single Systems 4 Cascadable Standard Multiswitches 8 Cascadable Multiswitches Unicable 16 Professional Multiswitches for Single Systems 18 Cascadable Professional Multiswitches 20 Power Supply Concept 24 Amplifiers 25 Accessories 28 DiSEqC Multiswitches 30 Wideband Amplifiers 32 Taps and Splitters 34 Antenna Outlets and Accessories 36 Dish Antennas and Accessories 38 LNBs 39 Installation Material 40 Order processing: Service: Bettina Wilmerstadt Margareta Kiss Phone: +49/9 11/7 03 - 72 09 Fax: +49/9 11/7 03 - 92 10 Email: [email protected] Phone: +49/9 11/7 03 - 22 21 Fax: +49/9 11/7 03 - 23 26 Email: [email protected] You will find every product for the installation of Broadband communication and SAT IF networks in this catalogue. Beginning with the satellite antenna with the corresponding LNB further to every necessary component of the satellite IF distribution equipment to the point of wall outlet - everything from one source. There are every necessary components for the range of broadband communication installation equipment after the feed-in of the corresponding signal - this equipment consists of broadband communication amplifiers, taps and splitters and wall outlets. There is the suitable product for every application. Two new multiswitches in the range of satellite IF distribution are added. There are a 24 and a 32 output multiswitch version with 16 satellite inputs and 1 terrestrial input. These multiswitches are featured with the well-known advantages of the current multiswitch portfolio: low power consumption and first-class isolation values. For the first time you will find for the most of the products a QR code. You can get to the relevant product site on our homepage and download e.g. the manual or assembly instruction for this product. We are sure that you can equip your distribution network with every necessary components from GSS. On behalf of the Board of Directors Fred Huebner 3 5 inputs Multiswitches with 4 SAT IF inputs and one active terrestrial input. The latter can be attenuated by up to 10 dB and also switched to passive stage which allows return-channel applications. A 22-kHz signal generator can be switched on for controlling Quad LNBs with integrated multiswitch. SDSP 504 SDSP 506 SDSP 508 SDSP 512 SDSP 516 No. of SAT inputs 4 4 4 4 4 No. of terrestrial inputs 1 1 1 1 1 No. of outputs 4 6 8 12 16 Frequency range SAT TERR RETURN CHANNEL 950 – 2200 MHz 87 – 862 MHz 5 – 65 MHz (if TERR is passive!) 22-kHz generator Tap loss • SAT TERR (passive) Distribution 1 dB 15 dB 1 dB 15 dB • 3 dB 18 dB • 3 dB 18 dB 3 dB 0 dB 0 dB -3 dB -3 dB > 30 dB > 25 dB > 20 dB 10 dB 10 dB > 30 dB > 25 dB > 20 dB 10 dB 10 dB > 30 dB > 25 dB > 20 dB 10 dB 10 dB > 30 dB > 25 dB > 20 dB 10 dB 10 dB 12 dB 15 dB 15 dB 18 dB 18 dB 7 dB 6 dB 7 dB 6 dB max. 101 dBμV max. 97 dBμV 7 dB 6 dB 7 dB 6 dB 7 dB 6 dB Feeding for receiver < 65 mA < 65 mA < 65 mA < 65 mA < 65 mA Power consumption without LNB 4.7 W 4.7 W 4.7 W 4.7 W 4.7 W 225x125x60 225x125x60 Return loss Hor./Vert. SAT/TERR Port/Port SAT TERR Return-channel loss Output level Noise figure SAT TERR SAT TERR Mains voltage Dimensions in mm 4 • > 30 dB > 25 dB > 20 dB 10 dB 10 dB Isolation TERR (active) 1 dB 12 dB • 100 – 230 V AC, 50/60 Hz 225x125x60 225x215x60 225x215x60 STANDARD MULTISWITCHES FOR SINGLE S YSTEMS 9 inputs Multiswitches with 8 SAT IF inputs and one active terrestrial input. The latter can be attenuated by up to 10 dB and also switched to passive stage which allows return-channel applications. A 22-kHz signal generator can be switched on for controlling Quad LNBs with integrated multiswitch. SDSP 904 SDSP 906 SDSP 908 SDSP 912 SDSP 916 SDSP 924 SDSP 932 No. of SAT inputs 8 8 8 8 8 8 8 No. of terrestrial inputs 1 1 1 1 1 1 1 No. of outputs 4 6 8 12 16 24 32 Frequency range SAT TERR RETURN CHANNEL 950 – 2200 MHz 87 – 862 MHz 5 – 65 MHz (if TERR is passive!) 22-kHz generator Tap loss • SAT TERR (passive) Distribution 3 dB 15 dB • 3 dB 15 dB • 5 dB 18 dB • 5 dB 18 dB • • 0 dB 28 dB 0 dB 28 dB 3 dB 0 dB 0 dB -3 dB -3 dB 0 dB 0 dB > 30 dB > 25 dB > 20 dB 10 dB 10 dB > 30 dB > 25 dB > 20 dB 10 dB 10 dB > 30 dB > 25 dB > 20 dB 10 dB 10 dB > 30 dB > 25 dB > 20 dB 10 dB 10 dB > 30 dB > 25 dB > 20 dB 10 dB 10 dB > 30 dB > 25 dB > 20 dB 10 dB 10 dB > 30 dB > 25 dB > 20 dB 10 dB 10 dB 12 dB 15 dB 15 dB 18 dB 18 dB 28 dB 28 dB 7 dB 6 dB 7 dB 6 dB max. 101 dBμV max. 97 dBμV 7 dB 7 dB 6 dB 6 dB 7 dB 6 dB 7 dB 8 dB Feeding for receiver < 65 mA < 65 mA < 65 mA < 65 mA < 65 mA < 30 mA < 30 mA Power consumption without LNB 4.7 W 4.7 W 4.7 W 4.7 W 4.7 W 9W 9W Isolation Return loss TERR (active) 3 dB 12 dB • Hor./Vert. SAT/TERR Port/Port SAT TERR Return-channel loss Output level Noise figure Mains voltage Dimensions in mm SAT TERR SAT TERR max. 95 dBμV max. 95 dBμV 7 dB 8 dB 100 – 230 V AC, 50/60 Hz 260x125x60 260x125x60 260x125x60 260x215x60 260x215x60 185x290x60 185x290x60 5 13 inputs Multiswitches with 12 SAT IF inputs and one active terrestrial input. The latter can be attenuated by up to 10 dB and also switched to passive stage which allows return-channel applications. SDSP 1308 SDSP 1312 SDSP 1316 No. of SAT inputs 12 12 12 No. of terrestrial inputs 1 1 1 No. of outputs 8 12 16 Frequency range SAT TERR RETURN CHANNEL 950 – 2200 MHz 87 – 862 MHz 5 – 65 MHz (if TERR is passive!) 22-kHz generator Tap loss — SAT TERR (passive) — 5 dB 15 dB 7 dB 18 dB 7 dB 18 dB 0 dB -3 dB -3 dB > 30 dB > 25 dB > 20 dB 10 dB 10 dB > 30 dB > 25 dB > 20 dB 10 dB 10 dB > 30 dB > 25 dB > 20 dB 10 dB 10 dB 15 dB 18 dB 18 dB 7 dB 6 dB max. 101 dBμV max. 97 dBμV 7 dB 6 dB 7 dB 6 dB Feeding for receiver < 65 mA < 65 mA < 65 mA Power consumption without LNB 3.5 W 3.5 W 3.5 W Distribution Isolation Return loss TERR (active) Hor./Vert. SAT/TERR Port/Port SAT TERR Return-channel loss Output level Noise figure SAT TERR SAT TERR Mains voltage Dimensions in mm 6 — 100 – 230 V AC, 50/60 Hz 340 x 125 x 60 340 x 215 x 60 340 x 215 x 60 STANDARD MULTISWITCHES FOR SINGLE S YSTEMS 17 inputs Multiswitches with 16 SAT IF inputs and one active terrestrial input. The latter can be attenuated by up to 10 dB and also switched to passive stage which allows return-channel applications. SDSP 1708 SDSP 1712 SDSP 1716 SDSP 1724 SDSP 1732 No. of SAT inputs 16 16 16 16 16 No. of terrestrial inputs 1 1 1 1 1 No. of outputs 8 12 16 24 32 Frequency range SAT TERR RETURN CHANNEL 950 – 2200 MHz 87 – 862 MHz 5 – 65 MHz (if TERR is passive!) 22-kHz generator Tap loss — SAT TERR (passive) Distribution 7 dB 18 dB — 7 dB 18 dB — — 0 dB 28 dB 0 dB 28 dB 0 dB -3 dB -3 dB 0 dB 0 dB > 30 dB > 25 dB > 20 dB 10 dB 10 dB > 30 dB > 25 dB > 20 dB 10 dB 10 dB > 30 dB > 25 dB > 20 dB 10 dB 10 dB > 30 dB > 25 dB > 20 dB 10 dB 10 dB > 30 dB > 25 dB > 20 dB 10 dB 10 dB 15 dB 18 dB 18 dB 28 dB 7 dB 6 dB max. 101 dBμV max. 97 dBμV 7 dB 6 dB 7 dB 6 dB 7 dB 8 dB Feeding for receiver < 65 mA < 65 mA < 65 mA < 30 mA < 30 mA Power consumption without LNB 3.5 W 3.5 W 3.5 W 9W 9W 340 x 125 x 60 340 x 215 x 60 Isolation Return loss TERR (active) 5 dB 15 dB — Hor./Vert. SAT/TERR Port/Port SAT TERR Return-channel loss Output level Noise figure SAT TERR SAT TERR Mains voltage Dimensions in mm 28 dB max. 95 dBμV max. 95 dBμV 7 dB 8 dB 100 – 230 V AC, 50/60 Hz 340 x 215 x 60 220 x 290 x 60 220 x 290 x 60 7 Satellite installation for digital and analogue reception of one satellite (e.g. ASTRA 19.2°) with terrestrial feed for up to 32 participants. The power supply unit can flexibly connected to any of the three multiswitches. 8 C AS C ADAB L E STANDARD MULTISWITCHES 5 inputs The cascadable multiswitch system consists of components with loop-through outputs and terminal units to be installed at the end of the distribution. The multiswitches with 4 SAT IF inputs have an additional passive terrestrial input which is capable for return-channel signals. A 22-kHz signal generator can be switched on for controlling Quad LNBs with integrated multiswitch. No. of SAT inputs SDC 504 SDC 508 SDC 516 4 4 4 No. of terrestrial inputs 1 1 1 No. of loop-through outputs 5 5 5 No. of receiver outputs Frequency range 4 8 SAT TERR RETURN CHANNEL 22-kHz generator Through loss SAT TERR Tap loss SAT TERR Isolation Hor./Vert. SAT/TERR Port/Port Return loss SAT TERR Return-channel loss Output level SAT TERR Noise figure SAT TERR Feeding for receiver Power consumption without LNB Mains voltage Dimensions in mm • 2 dB 2 dB 1 dB 20 dB > 30 dB > 25 dB > 20 dB 10 dB 10 dB 20 dB 16 950 – 2200 MHz 87 – 862 MHz 5 – 65 MHz • 2 dB 2 dB 1 dB 23 dB > 30 dB > 25 dB > 20 dB 10 dB 10 dB 23 dB • 4 dB 4 dB 3 dB 25 dB > 30 dB > 25 dB > 20 dB 10 dB 10 dB 25 dB max. 101 dBμV passive 7 dB passive < 65 mA 7 dB passive < 65 mA 7 dB passive < 65 mA 1.5 W 1.5 W 1.5 W 125x135x60 125x135x60 via SDP 900 125x225x60 9 Satellite installation for digital and analogue reception of two satellites (e.g. ASTRA 19.2° and Eutelsat 13°) with terrestrial feed for up to 76 participants. The input signals are fed via a SAT IF amplifier. 10 C AS C ADAB L E STANDARD MULTISWITCHES 9 inputs The cascadable multiswitch system consists of components with loop-through outputs and terminal units to be installed at the end of the distribution. The multiswitches with 8 SAT IF inputs have an additional passive terrestrial input which is capable for return-channel signals. A 22-kHz signal generator can be switched on for controlling Quad LNBs with integrated multiswitch. SDC 904 SDC 906 SDC 908 SDC 912 SDC 916 No. of SAT inputs 8 8 8 8 8 No. of terrestrial inputs 1 1 1 1 1 No. of loop-through outputs 9 9 9 9 9 No. of receiver outputs 4 6 8 12 16 Frequency range SAT TERR RETURN CHANNEL 950 – 2200 MHz 87 – 862 MHz 5 – 65 MHz 22-kHz generator Through loss Tap loss Isolation Return loss Return-channel loss Output level Noise figure Feeding for receiver • SAT TERR SAT TERR Hor./Vert. SAT/TERR Port/Port SAT TERR • • • • 2 dB 2 dB 3 dB 20 dB > 30 dB > 25 dB > 20 dB 10 dB 10 dB 2 dB 2 dB 3 dB 23 dB > 30 dB > 25 dB > 20 dB 10 dB 10 dB 2 dB 2 dB 3 dB 23 dB > 30 dB > 25 dB > 20 dB 10 dB 10 dB 4 dB 4 dB 5 dB 25 dB > 30 dB > 25 dB > 20 dB 10 dB 10 dB 4 dB 4 dB 5 dB 25 dB > 30 dB > 25 dB > 20 dB 10 dB 10 dB 20 dB 23 dB 23 dB 25 dB 25 dB 7 dB passive max. 101dBμV passive 7 dB passive 7 dB passive 7 dB passive < 65 mA < 65 mA < 65 mA < 65 mA SAT TERR SAT 7 dB TERR passive < 65 mA Power consumption without LNB 1.5 W 1.5 W 1.5 W 1.5 W 1.5 W Mains voltage via SDP 900 via SDP 900 via SDP 900 via SDP 900 via SDP 900 Dimensions in mm 160x135x60 160x135x60 160x135x60 160x225x60 160x225x60 11 Satellite installation for digital and analogue reception of up to three satellites (e.g. ASTRA 19.2°, Eutelsat 13° and Turksat) with terrestrial feed for up to 72 participants. The input signals are fed via two SAT IF amplifiers. 12 C AS C ADAB L E STANDARD MULTISWITCHES 13 inputs The cascadable multiswitch system consists of components with loop-through outputs and terminal units to be installed at the end of the distribution. The multiswitches with 12 SAT IF inputs have an additional passive terrestrial input which is capable for return-channel signals. SDC 1308 SDC 1312 SDC 1316 No. of SAT inputs 12 12 12 No. of terrestrial inputs 1 1 1 No. of loop-through outputs 13 13 13 No. of receiver outputs 8 12 Frequency range SAT TERR RETURN CHANNEL 22-kHz generator Through loss 16 950 – 2200 MHz 87 – 862 MHz 5 – 65 MHz — — — 2 dB 2 dB 5 dB 23 dB > 30 dB > 25 dB > 20 dB 10 dB 10 dB 4 dB 4 dB 7 dB 25 dB > 30 dB > 25 dB > 20 dB 10 dB 10 dB 4 dB 4 dB 7 dB 25 dB > 30 dB > 25 dB > 20 dB 10 dB 10 dB 23 dB 25 dB 25 dB max. 101dBμV passive 7 dB passive max. 101dBμV passive 7 dB passive max. 101dBμV passive 7 dB passive Feeding for receiver < 65 mA < 65 mA < 65 mA Power consumption without LNB 1.5 W 1.5 W 1.5 W Mains voltage via SDP 1700 via SDP 1700 via SDP 1700 Dimensions in mm 240 x 135 x 60 240 x 225 x 60 240 x 225 x 60 Tap loss Isolation Return loss SAT TERR SAT TERR Hor./Vert. SAT/TERR Port/Port SAT TERR Return-channel loss Output level Noise figure SAT TERR SAT TERR 13 Satellite installation for digital and analogue reception of up to four satellites (e.g. ASTRA 19.2°, ASTRA 23.5°, Eutelsat 13° and Turksat) with terrestrial feed for up to 36 participants. The power supply unit can flexibly connected to any of the three multiswitches. 14 C AS C ADABL E STANDARD MULTISWITCHES 17 inputs The cascadable multiswitch system consists of components with loop-through outputs and terminal units to be installed at the end of the distribution. The multiswitches with 16 SAT IF inputs have an additional passive terrestrial input which is capable for return-channel signals. SDC 1708 SDC 1712 SDC 1716 No. of SAT inputs 16 16 16 No. of terrestrial inputs 1 1 1 No. of loop-through outputs 17 17 17 No. of receiver outputs 8 12 Frequency range SAT TERR RETURN CHANNEL 22-kHz generator Through loss Tap loss Isolation Return loss 16 950 – 2200 MHz 87 – 862 MHz 5 – 65 MHz — SAT TERR SAT TERR Hor./Vert. SAT/TERR Port/Port SAT TERR Return-channel loss 2 dB 2 dB 5 dB 23 dB > 30 dB > 25 dB > 20 dB 10 dB 10 dB — 4 dB 4 dB 7 dB 25 dB > 30 dB > 25 dB > 20 dB 10 dB 10 dB — 4 dB 4 dB 7 dB 25 dB > 30 dB > 25 dB > 20 dB 10 dB 10 dB 23 dB 25 dB 25 dB max. 101dBμV passive 7 dB passive max. 101dBμV passive 7 dB passive max. 101dBμV passive 7 dB passive Feeding for receiver < 65 mA < 65 mA < 65 mA Power consumption without LNB 1.5 W 1.5 W 1.5 W Mains voltage via SDP 1700 via SDP 1700 via SDP 1700 Dimensions in mm 240 x 135 x 60 240 x 225 x 60 240 x 225 x 60 Output level Noise figure SAT TERR SAT TERR 15 1-4 1-4 Satellite installation for digital reception of one satellite (e.g. ASTRA 19.2°) with terrestrial feed for up to 16 participants with receiver which support the Unicable standard. The power supply unit can flexibly connected to any of the both multiswitches. 16 SRS 205 1-8 C AS C ADAB L E MULTISWITCHES UNIC ABLE A 22-kHz signal generator can be switched on for controlling Quad LNBs with integrated multiswitch. Cascadable multiswitches Unicable The cascadable multiswitch system unicable consists of satellite and terrestrial inputs as well as loop-through outputs. An optional switching power supply can be used for low current consumption and noise-free transmission of the signals. The terrestrial input is suitable for return-path signals. Both outputs can be combined with the splitter SRS 205 for creating a rope for 8 receivers. SDUC 502 SDUC 902 No. of SAT inputs 4 8 No. of terrestrial inputs 1 1 No. of loop-through outputs 5 9 Output frequencies output 1/chanel ID 1284 MHz / 0 1400 MHz / 1 1516 MHz / 2 1632 MHz / 3 1748 MHz / 4 1864 MHz / 5 1980 MHz / 6 2096 MHz / 7 950 – 2200 MHz 87 – 862 MHz 5 – 65 MHz Output frequencies output 2/channel ID Frequency range SAT TERR RETURN CHANNEL • 22-kHz generator Through loss Tap loss • SAT 2 dB TERR 3.5 dB TERR (passive) 10 dB 2 dB 3.5 dB 10 dB SAT 14 dB 14 dB SAT 10 dB TERR 10 dB TERR 10 dB 10 dB 10 dB 10 dB Gain Return loss Return-channel loss Feeding for receiver < 30 mA < 30 mA Power consumption without LNB 7W 7W via SDP 900 Mains voltage Dimensions in mm 135 x 160 x 60 135 x 160 x 60 17 5 inputs Multiswitches with 4 SAT IF inputs and one active terrestrial input. The latter can be attenuated by up to 10 dB and also switched to passive stage with allows return-path applications. A 22-kHz signal generator can be switched on for controlling Quad LNBs with integrated multiswitch. PDSP 504 PDSP 506 PDSP 508 No. of SAT inputs 4 4 4 No. of terrestrial inputs 1 1 1 No. of outputs 4 6 Frequency range SAT TERR RETURN CHANNEL 22-kHz generator Tap loss • SAT TERR (passive) Gain Isolation Return loss TERR (active) Hor./Vert. SAT/TERR Port/Port SAT TERR Return-channel loss Output level Noise figure SAT TERR SAT TERR 0 dB 17 dB • 0 dB 17 dB • 0 dB 17 dB 0 dB 0 dB 0 dB > 30 dB > 25 dB > 20 dB 10 dB 10 dB > 30 dB > 25 dB > 20 dB 10 dB 10 dB > 30 dB > 25 dB > 20 dB 10 dB 10 dB 17 dB 17 dB 17 dB max. 101 dBμV max. 97 dB 7 dB 6 dB 7 dB 6 dB 7 dB 6 dB Feeding for receiver < 65 mA < 65 mA < 65 mA Power consumption without LNB 4.7 W 4.7 W 4.7 W Mains voltage Dimensions in mm 18 8 950 – 2200 MHz 87 – 862 MHz 5 – 65 MHz 100 – 230 V AC / 50/60 Hz 230 x 133 x 55 230 x 133 x 55 230 x 133 x 55 P ROF ES S IONAL M ULTISW ITC H E S FOR SINGLE S YSTEMS 9 inputs Multiswitches with 8 SAT IF inputs and one active terrestrial input. The latter can be attenuated by up to 10 dB and also switched to passive stage with allows return-path applications. A 22-kHz signal generator can be switched on for controlling Quad LNBs with integrated multiswitch. PDSP 904 PDSP 906 PDSP 908 No. of SAT inputs 8 8 8 No. of terrestrial inputs 1 1 1 No. of outputs 4 6 Frequency range SAT TERR RETURN CHANNEL 22-kHz generator Tap loss 8 950 – 2200 MHz 87 – 862 MHz 5 – 65 MHz • SAT TERR (passive) Gain Isolation Return loss TERR (active) Hor./Vert. SAT/TERR Port/Port SAT TERR Return-channel loss Output level Noise figure SAT TERR SAT TERR 0 dB 17 dB • 0 dB 17 dB • 0 dB 17 dB 0 dB 0 dB 0 dB > 30 dB > 25 dB > 20 dB 10 dB 10 dB > 30 dB > 25 dB > 20 dB 10 dB 10 dB > 30 dB > 25 dB > 20 dB 10 dB 10 dB 17 dB 17 dB 17 dB max. 101 dBμV max. 97 dB 7 dB 6 dB 7 dB 6 dB 7 dB 6 dB Feeding for receiver < 65 mA < 65 mA < 65 mA Power consumption without LNB 4.7 W 4.7 W 4.7 W Mains voltage Dimensions in mm 100 – 230 V AC / 50/60 Hz 230 x 133 x 55 230 x 133 x 55 230 x 133 x 55 19 Satellite installation for digital and analogue reception of one satellite (e.g. ASTRA 19.2°) with terrestrial feed for up to 18 participants. The power supply unit can flexibly connected to any of the three multiswitches. 20 C AS C ADAB L E PROF ES S IONAL M ULTISW ITC H E S 5 inputs The cascadable multiswitch system consists of satellite and terrestrial inputs as well as loop-through outputs. An optional switching power supply can be used for low current consumption and noise-free transmission of the signals. A 22-kHz signal generator can be switched on for controlling Quad LNBs with integrated multiswitch. The terrestrial input is suitable for return-path signals. PDC 504 PDC 506 PDC 508 No. of SAT inputs 4 4 4 No. of terrestrial inputs 1 1 1 No. of loop-through outputs 5 5 5 No. of receiver outputs 4 6 Frequency range SAT TERR RETURN CHANNEL 22-kHz generator Through loss Tap loss Isolation Return loss • SAT TERR SAT TERR Hor./Vert. SAT/TERR Port/Port SAT TERR Return-channel loss Output level 8 950 – 2200 MHz 87 – 862 MHz 5 – 65 MHz • 3 dB 3 dB 0 dB 23 dB > 30 dB > 25 dB > 20 dB 10 dB 10 dB 3 dB 3 dB 0 dB 23 dB > 30 dB > 25 dB > 20 dB 10 dB 10 dB 23 dB 23 dB 23 dB SAT TERR Noise figure • 3 dB 3 dB 0 dB 23 dB > 30 dB > 25 dB > 20 dB 10 dB 10 dB max. 101 dBμV passive 7 dB 7 dB Feeding for receiver SAT 7 dB < 65 mA < 65 mA < 65 mA Power consumption without LNB 1.5 W 1.5 W 1.5 W Mains voltage Dimensions in mm via PDP 900 165 x 133 x 55 165 x 133 x 55 165 x 133 x 55 21 Satellite installation for digital and analogue reception of two satellites (e.g. ASTRA 19.2° and Eutelsat 13°) with terrestrial feed for up to 42 participants. The input signals are fed via a SAT IF amplifier. 22 C AS C ADAB L E PROF ES S IONAL M ULTISW ITC H E S 9 inputs The cascadable multiswitch system consists of satellite and terrestrial inputs as well as loop-through outputs. An optional switching power supply can be used for low current consumption and noise-free transmission of the signals. A 22-kHz signal generator can be switched on for controlling Quad LNBs with integrated multiswitch. The terrestrial input is suitable for return-path signals. PDC 904 PDC 906 PDC 908 No. of SAT inputs 8 8 8 No. of terrestrial inputs 1 1 1 No. of loop-through outputs 9 9 9 No. of receiver outputs 4 6 Frequency range SAT TERR RETURN CHANNEL 22-kHz generator Through loss Tap loss Isolation Return loss • SAT TERR SAT TERR Hor./Vert. SAT/TERR Port/Port SAT TERR Return-channel loss Output level 8 950 – 2200 MHz 87 – 862 MHz 5 – 65 MHz • 3 dB 3 dB 0 dB 23 dB > 30 dB > 25 dB > 20 dB 10 dB 10 dB 3 dB 3 dB 0 dB 23 dB > 30 dB > 25 dB > 20 dB 10 dB 10 dB 23 dB 23 dB 23 dB SAT TERR Noise figure • 3 dB 3 dB 0 dB 23 dB > 30 dB > 25 dB > 20 dB 10 dB 10 dB max. 101 dBμV passive 7 dB 7 dB Feeding for receiver SAT 7 dB < 65 mA < 65 mA < 65 mA Power consumption without LNB 1.5 W 1.5 W 1.5 W Mains voltage Dimensions in mm via PDP 900 165 x 133 x 55 165 x 133 x 55 165 x 133 x 55 23 POWER SUPPLY CONCEPT The idea of the GSS-SAT IF distribution system allows a flexible positioning of the power supply units. As a power supply unit can be connected to each component of the SAT IF distribution to feed each other device of the distribution system like multiswitches, amplifiers or LNBs it can be placed wherever you want and wherever necessary. 24 AM PLIF IE RS SAT IF Amplifier The amplifiers SDA 900 and SDA 500 can be used for huge distribution networks. These types have 9 resp. 5 inputs and 18 resp. 10 outputs. SDA 500 SDA 900 No. of SAT inputs 4 8 No. of terrestrial inputs 1 1 No. of outputs SAT TERR Frequency range SAT TERR Gain SAT LINE SAT TAP TERR LINE TERR TAP 8 2 950 - 2200 MHz 40 - 862 MHz 32 dB 25 dB 25 dB 15 dB 16 2 950 - 2200 MHz 40 - 862 MHz 32 dB 25 dB 25 dB 15 dB Isolation > 70 dB > 70 dB Attenuation Slope Output level – IMA 3 – 0 … 15 dB 0 … 7 dB max. 114 dBμV max. 107 dBμV max. 114 dBμV max. 104 dBμV max. 112 dBμV max. 105 dBμV max. 112 dBμV max. 102 dBμV 0 … 15 dB 0 … 7 dB max. 114 dBμV max. 107 dBμV max. 114 dBμV max. 104 dBμV max. 112 dBμV max. 105 dBμV max. 112 dBμV max. 102 dBμV Noise figure 8 dB 8 dB Return loss 10 dB 10 dB Power supply *) 15 V DC 15 V DC Current consumption 750 mA 750 mA Ambient temperature -20° … +50° C -20° … +50° C Dimensions approx. in mm 107 x 142 x 80 193 x 142 x 80 Output level – IMA 2 – SAT LINE SAT TAP TERR LINE TERR TAP SAT LINE SAT TAP TERR LINE TERR TAP *) via delivered power supply unit SDA 15 No. of SAT inputs 4 No. of SAT outputs 4 Frequency range 950 ... 2200 MHz Gain + 14,5 dB Isolation > 70 dB Attenuation 0 ... -10 dB Plugging on Amplifier SDA 15 Plugging on amplifier for 4 SAT IF inputs, gain 14.5 dB max. 103 dBμV (35 dB IMA 3 Ord.) Return loss 10 dB Current consumption SDA 15 ca. 40 mA Output level Current consumption LNC max. 400 mA Ambient temperature -20°C ... +50°C Dimensions approx. in mm 36 x 67 x 62 25 Multi-Amplifier At huge SAT IF distribution systems it may be necessary to use multi-amplifier components for tapped signals in order to level the SAT IF signals. For this case the GSS models with 5 and 9 inputs and outputs with 12 dB and 20 dB gain are the right choice. They are fed by the power supply units of the SAT IF system (e.g. via the power supply unit of the multiswitch). The power supply unit SDP 152 (15 V/2 A) is optionally available if it is necessary! Frequency range Gain SAT TERR SAT TERR Attenuation TERR Return loss SAT TERR SAT TERR SAT TERR Output level Noise figure SDA 512 SDA 520 SDA 912 SDA 920 950 – 2200 MHz 10 – 862 MHz 8 – 12 dB 12 dB 950 – 2200 MHz 10 – 862 MHz 15 – 20 dB 20 dB 950 – 2200 MHz 10 – 862 MHz 8 – 12 dB 12 dB 950 – 2200 MHz 10 – 862 MHz 15 – 20 dB 20 dB — 10 dB 10 dB max. 110 dBμV max. 106 dBμV 7 dB 6 dB 0 – 15 dB 10 dB 10 dB max. 113 dBμV max. 106 dBμV 7 dB 6 dB — 10 dB 10 dB max. 110 dBμV max. 106 dBμV 7 dB 6 dB 0 – 15 dB 10 dB 10 dB max. 113 dBμV max. 106 dBμV 7 dB 6 dB Current consumption 15 V/180 mA 15 V/250 mA 15 V/220 mA 15 V/450 mA Remote current supply Dimensions in mm max. 1000 mA 145 x 71 x 35 max. 1000 mA 145 x 71 x 35 max. 1000 mA 210 x 71 x 35 max. 1000 mA 210 x 71 x 35 26 AM P LIF IE RS Multi-Amplifier At huge SAT IF distribution systems it may be necessary to use multi-amplifier components for tapped signals in order to level the SAT IF signals. There are models with 5 and 9 inputs and outputs with a gain of 20 dB. Every input (TERR + SAT) is equipped with an attenuation controller by 15 dB. They are fed by the power supply units of the SAT IF system (e.g. via the power supply unit of the multiswitch). The power supply unit SDP 152 (15 V/2 A) is optionally available if it is necessary! SDA 521 SDA 921 950 – 2200 MHz 10 – 862 MHz 15 – 20 dB 20 dB 950 – 2200 MHz 10 – 862 MHz 15 – 20 dB 20 dB Attenuation control 0 – 15 dB 0 – 15 dB Return loss 12 dB Frequency range Gain Output level SAT TERR SAT TERR SAT 111 dBμV TERR 109 dBμV 12 dB 111 dBμV 109 dBμV Noise figure 5 dB 5 dB Current consumption 15 V / 250 mA 15 V / 500 mA Remote current supply max. 1000 mA max. 1000 mA Dimensions in mm 145 x 71 x 35 210 x 71 x 35 27 Multi-Tap Multi-Taps are necessary for tapping the signals at huge SAT IF distribution systems. There are models with 5 loop-through and tap outputs available resp. 9 loopthrough and tap outputs. The power supply unit SDP 152 (15 V/2 A) is optionally available if it is necessary! SDM 512 SDM 912 SDM 522 SDM 922 Frequency range SAT TERR Tap loss SAT TERR RETURN CHANNEL Through loss SAT TERR RETURN CHANNEL Return loss SAT TERR 950 – 2200 MHz 10 – 862 MHz 12 – 16 dB 12 dB 12 dB 1.8 dB 2 dB 2 dB 10 dB 10 dB 950 – 2200 MHz 10 – 862 MHz 12 – 16 dB 12 dB 12 dB 1.8 dB 2 dB 2 dB 10 dB 10 dB 950 – 2200 MHz 10 – 862 MHz 2 x 11 – 17 dB 2 x 15 dB 2 x 15 dB 2 – 3 dB 1 dB 1 dB 10 dB 10 dB 950 – 2200 MHz 10 – 862 MHz 2 x 11 – 17 dB 2 x 15 dB 2 x 15 dB 2 – 3 dB 1 dB 1 dB 10 dB 10 dB Remote current supply max. 1000 mA max. 1000 mA max. 1000 mA max. 1000 mA Dimensions in mm 145 x 71 x 35 210 x 71 x 35 199 x 98 x 35 254 x 98 x 35 28 AC C ES S OR I E S Multi Splitter Multi splitter are necessary for splitting the satellite signals at the end of a satellite IF line. There are models with double 5 and 9 splitting outputs. The power supply unit SDP 152 (15 V/2 A) is optionally available if it is necessary! SDS 526 SDS 926 950 – 2200 MHz 5 – 862 MHz 2 x 6 dB 2 x 4 dB 950 – 2200 MHz 5 – 862 MHz 2 x 6 dB 2 x 4 dB Isolation > 30 dB > 30 dB Return loss 12 dB 12 dB Frequency range SAT TERR SAT TERR Split-loss Remote current supply max 1000 mA max 1000 mA Dimensions in mm 145 x 71 x 35 210 x 71 x 35 Power Supply Unit for SDC, SDT and SDUC SDP 900 for SDC/SDT/SDUC 5XX – 9XX 100 V … 230 V AC, 50/60 Hz SDP 1700 for SDC/SDT 13XX – 17XX 100 V … 230 V AC, 50/60 Hz PDP 900 for PDC 5XX and 9XX 100 V … 230 V AC, 50/60 Hz 18 V DC 15 V DC 18 V DC Max. output current 1000 mA DC 2000 mA DC 1000 mA DC Ambient temperature -20° … + 50° C -20° … + 50° C -20° … + 50° C Dimensions approx. in mm 122 x 112 x 60 122 x 112 x 60 82 x 133 x 55 Mains voltage Output voltage Power Supply Unit for PDC 29 DiSEqC multiswitches are needed for satellite reception sytems to distribute the signals to one receiver. With these switches one receiver can get access to the signals of up to four satellites. 30 DiSEqC MULTISWITCHES DiSEqC Multiswitches DiSEqC multiswitches are needed for satellite reception sytems to distribute the signals to one receiver. With these switches one receiver can get access to the signals of up to four satellites. They are operated by the connected receiver without any external power supply. The GSS DiSEqC multiswitches are supplied with an UV and weather resistant housing which can be mounted either at an aerial mast or at walls. No. of SAT inputs SD 201 SD 301 SD 401 SD 501 2 2 4 4 No. of terrestrial inputs – No. of outputs Frequency range Through loss 1 SAT 950 – 2400 MHz TERR – SAT 1 dB TERR – 1 – 1 1 1 1 950 – 2400 MHz 47 – 862 MHz 2 dB 0,5 dB 950 – 2400 MHz – 1 dB – 950 – 2400 MHz 47 – 862 MHz 2,5 dB 0,5 dB Return loss > 12 dB > 12 dB > 12 dB > 12 dB DiSEqC control DiSEqC 2.0 DiSEqC 2.0 DiSEqC 2.0 DiSEqC 2.0 Isolation > 30 dB > 30 dB > 30 dB > 30 dB Linearity ± 1 dB ± 1 dB ± 1 dB ± 1 dB Control signal Position Position Position/Option Position/Option Remote current supply max. 700 mA max. 700 mA max. 700 mA max. 700 mA Current consumption < 30 mA < 30 mA < 30 mA < 30 mA 50 x 45 x 18 80 x 45 x 18 80 x 45 x 18 90 x 45 x 18 75 x 75 x 45 105 x 75 x 45 105 x 75 x 45 105 x 75 x 45 97 g 133 g 136 g 141 g Dimensions without weather resistant housing in mm Dimensions with weather resistant housing in mm Weight 31 AR 4218, AR 4298 Distribution amplifiers for single and master antenna systems. Frequency range up to 862 MHz. Output adjustable with variable level controller. 230 V mains voltage. AR 4218 AR 4298 Frequency range 40 – 862 MHz 40 – 862 MHz Gain 21 dB 29 dB Noise figure typ. 6 dB 6 dB Output level, IMR = 60 dB IMR 2 acc. EN 50083-3 IMR 3 acc. EN 50083-3 IMR 3 acc. EN 50083-5 CSO Cenelec 42 channels 862 MHz CTB Cenelec 42 channels 862 MHz 100 dBμV 107 dBμV 113 dBμV 97 dBμV 100 dBμV 105 dBμV 109 dBμV 115 dBμV 101 dBμV 101 dBμV Attenuator 0 to -20 dB 0 to -20 dB Mains voltage (50 - 60 Hz) 230 V AC 230 V AC Power consumption 3W 5W RF connectors F connectors F connectors Weight approx. 700 g approx. 700 g Dimensions (W x H x D) 170 x 90 x 50 mm 170 x 90 x 50 mm AR 5218, AR 5298 Distribution amplifiers for single and master antenna systems. Frequency range up to 862 MHz. Return-path up to 65 MHz either active or passive switchable. Output level and equalization adjustable with variable controllers. 230 V mains voltage. AR 5218 AR 5298 Frequency range 85 – 862 MHz 85 – 862 MHz Frequency range return-path 5 – 65 MHz 5 – 65 MHz Gain 21 dB 29 dB Gain return-path 19 dB 24 dB Noise figure typ. 6 dB 6 dB 100 dBμV 102 dBμV 107 dBμV 107 dBμV 113 dBμV 113 dBμV 97 dBμV 100 dBμV 105 dBμV 102 dBμV 109 dBμV 107 dBμV 115 dBμV 113 dBμV 101 dBμV 101 dBμV Output level, IMR = 60 dB IMR 2 acc. EN 50083-3 forward return IMR 3 acc. EN 50083-3 forward return IMR 3 acc. EN 50083-5 forward return CSO Cenelec 42 channels 862 MHz CTB Cenelec 42 channels 862 MHz Attenuator 0 to -20 dB 0 to -20 dB Adjustable line equalization 0 to 18 dB 0 to 18 dB Mains voltage (50 – 60 Hz) 230 V AC 230 V AC Power consumption 4.5 W 6W RF connectors F connectors F connectors Weight approx. 700 g approx. 700 g Dimesions (W x H x D) 170 x 90 x 50 mm 170 x 90 x 50 mm 32 W IDEBAND AM PLIF IE RS AR 5368 Distribution amplifiers for single and master antenna systems in cast housing with particulary good cooling properties. Frequency range up to 862 MHz. Return-path up to 65 MHz either active or passive switchable. Selection of the level and the equalization via discrete and switchable attenuation and equalization links. 230 V mains voltage. AR 5368 Frequency range 40 (85) – 862 MHz Frequency range return-path 5 – 65 MHz Gain 36 dB Gain return-path 27 dB Noise figure typ. 5.5 dB Output level, IMR = 60 dB IMR 2 acc. EN 50083-3 CSO Cenelec 42 channels 862 MHz CTB Cenelec 42 channels 862 MHz forward return forward return forward return 114 dBμV 104 dBμV 123 dBμV 115 dBμV 109 dBμV 108 dBμV Attenuators at input (2-dB steps) at input (2-dB steps) at output Interstage forward return return forward 0 to 16 dB 0 to 6 dB/50 dB 0/3/6/9 dB 0/6 dB Line equalization at input (2-dB steps) Interstage slope Interstage slope forward forward return 0 to 16 dB 0/7 dB 0/3/6 dB IMR 3 acc. EN 50083-5 Mains voltage (50 – 60 Hz) 180 – 253 V AC Power consumption 9W RF connectors F connectors Weight approx. 2.0 kg Dimensions (W x H x D) 190 x 110 x 80 mm On our homepage you will find the actual technical datas for the Wideband Amplifiers. 33 Splitter SR 812 SR 610 SR 407 SR 305 SR 203 No. of outputs 8 6 4 3 2 Frequency range 5 – 1000 MHz 5 – 1000 MHz 5 – 862 MHz 5 – 862 MHz 5 – 862 MHz 11.0 dB 11.0 dB 12.5 dB 24 dB 24 dB 20 dB 20 dB 18 dB 18 dB 9.3 dB 9.8 dB 10.5 dB 20 dB 22 dB 20 dB 18 dB 18 dB 18 dB 7.4 dB 7.4 dB 7.4 dB 16 dB 23 dB 23 dB > 14 dB > 20 dB1) > 20 dB1) 5.5 dB 5.5 dB 5.5 dB 16 dB 20 dB 20 dB > 14 dB 20 dB1) 20 dB1) 3.4 dB 3.4 dB 3.4 dB 20 dB 23 dB 23 dB > 16 dB 20 dB1) 20 dB1) Connectors F connector F connector F connector F connector F connector Single-Tap TR 116 TR 112 TR 108 No. of outputs 1 1 1 Frequency range 5 – 862 MHz 5 – 862 MHz 5 – 862 MHz Connectors 16.0 dB 16.0 dB 16.0 dB 0.8 dB 0.5 dB 0.8 dB > 14 dB > 20 dB1) > 20 dB1) > 30 dB > 26 dB > 26 dB F connector 12.0 dB 12.0 dB 12.0 dB 1.0 dB 0.7 dB 1.0 dB > 14 dB > 20 dB1) > 20 dB1) > 30 dB > 30 dB > 26 dB F connector 8.5 dB 8.5 dB 8.5 dB 1.8 dB 1.6 dB 1.8 dB > 14 dB > 20 dB1) > 20 dB1) > 22 dB > 30 dB > 22 dB F connector Double-Tap TR 216 TR 212 TR 208 No. of outputs 2 2 2 Splitt-loss Isolation Return-loss Tap-loss Through-loss Return-loss Directional-loss 5 – 40 MHz 40 – 470 MHz 470 – 862 MHz 5 – 40 MHz 40 – 470 MHz 470 – 862 MHz 5 – 40 MHz 40 – 470 MHz 470 – 862 MHz 5 – 40 MHz 40 – 470 MHz 470 – 862 MHz 5 – 40 MHz 40 – 470 MHz 470 – 862 MHz 5 – 40 MHz 40 – 470 MHz 470 – 862 MHz 5 – 40 MHz 40 – 470 MHz 470 – 862 MHz Frequency range Tap-loss Through-loss Isolation Return-loss Directional-loss Connectors 5 – 40 MHz 40 – 470 MHz 470 – 862 MHz 5 – 40 MHz 40 – 470 MHz 470 – 862 MHz 5 – 40 MHz 40 – 470 MHz 470 – 862 MHz 5 – 40 MHz 40 – 470 MHz 470 – 862 MHz 5 – 40 MHz 40 – 470 MHz 470 – 862 MHz 5 – 862 MHz 5 – 862 MHz 5 – 862 MHz 16.5 dB 16.5 dB 16.5 dB 1.4 dB 0.8 dB 1.4 dB 40 dB 40 dB 36 dB > 14 dB > 20 dB1) > 20 dB1) > 26 dB > 30 dB > 26 dB 12.5 dB 12.5 dB 12.5 dB 1.4 dB 1.2 dB 1.8 dB 40 dB 40 dB 36 dB > 14 dB > 20 dB1) > 20 dB1) > 28 dB > 28 dB > 22 dB 8.5 dB 8.5 dB 8.5 dB 3.7 dB 2.8 dB 3.4 dB 26 dB 26 dB 22 dB > 14 dB > 20 dB1) > 20 dB1) > 18 dB > 18 dB > 16 dB F connector F connector F connector 1) at 40 MHz, -1.5 dB per octave 34 High performance passive taps and splitters with F connector technology for installation of wideband cable distribution networks. Designed as single taps, double taps or multiple taps as well as splitters with 2, 3 and 4 connections, they ensure economical planning of distribution networks. All components fulfil the higher shielding rating required for class A according to the standard EN 50083-2/-4 and are decoupled to prevent hum. TAP S / S PLITTE RS Multi-Tap MTR 08 MTR 06 MTR 04 No. of outputs 8 6 4 Frequency range 5 – 862 MHz 5 – 862 MHz 5 – 862 MHz 12.5 dB 13.5 dB 14.5 dB 15.5 dB 16.5 dB 17.5 dB 18.0 dB 19.0 dB 9.5 dB 8.0 dB 8.0 dB 36 dB 40 dB 36 dB > 12 dB > 20 dB1) > 20 dB1) > 26 dB > 30 dB > 26 dB 12.5 dB 13.5 dB 14.5 dB 15.5 dB 16.5 dB 17.5 dB – – 6.5 dB 6.0 dB 6.0 dB 36 dB 40 dB 36 dB > 12 dB > 20 dB1) > 20 dB1) > 26 dB > 30 dB > 26 dB 12.5 dB 13.5 dB 14.5 dB 15.0 dB – – – – 4.5 dB 3.8 dB 3.8 dB 36 dB 40 dB 36 dB > 12 dB > 20 dB1) > 20 dB1) > 26 dB > 30 dB > 26 dB F connector F connector F connector Tap-loss Through-loss Isolation Return-loss Directional-loss Output 1 Output 2 Output 3 Output 4 Output 5 Output 6 Output 7 Output 8 5 – 40 MHz 40 – 470 MHz 470 – 862 MHz 5 – 40 MHz 40 – 470 MHz 470 – 862 MHz 5 – 40 MHz 40 – 470 MHz 470 – 862 MHz 5 – 40 MHz 40 – 470 MHz 470 – 862 MHz Connectors 1) at 40 MHz, -1.5 dB per octave Splitters Splitters with F connector technology for the 1st SAT IF for splitting SAT signals, e.g. in Unicable systems or in connection with head-end station systems. The splitter satisfies the higher shielding requirements of class A according to standard EN 50083-2/A1. Splitter SRS 408 DC SRS 308 DC SRS 207 DC SRS 205 No. of outputs 4 3 2 2 No. of outputs with diode protection • • • - Frequency range 40 – 2400 MHz 40 – 2400 MHz 40 – 2400 MHz 40 – 2400 MHz 7.5 dB 8.5 dB 9.0 dB 9.5 dB 20 dB 16 dB 16 dB 16 dB 12 dB 10 dB 10 dB 10 dB 7.0 dB 8.0 dB 8.5 dB 9.0 dB 16 dB 14 dB 14 dB 14 dB 12 dB 10 dB 10 dB 10 dB 4.0 dB 5.0 dB 7.0 dB 7.0 dB 16 dB 14 dB 12 dB 12 dB 18 dB 8 dB 8 dB 8 dB 4.0 dB 5.0 dB 7.0 dB 7.0 dB 16 dB 14 dB 12 dB 12 dB 18 dB 8 dB 8 dB 8 dB F connector F connector F connector F connector Split-loss Isolation Return-loss 40 – 860 MHz 950 – 1750 MHz 1750 – 2150 MHz 2150 – 2400 MHz 40 – 860 MHz 950 – 1750 MHz 1750 – 2150 MHz 2150 – 2400 MHz 40 – 860 MHz 950 – 1750 MHz 1750 – 2150 MHz 2150 – 2400 MHz Connectors On our homepage you will find the latest technical data for taps and splitters. 35 OR series The OR series antenna outlets can be used in distribution networks up to 862 MHz. They are designed for connection of one radio receiver and one TV. The designs as throughtype outlet with staged output attenuations and stub cable outlet ensure economical planning of distribution networks with trunk or star structure. The return channel compatibility and the high return flow attenuation satisfies the requirements for interactive networks for data transmission. The antenna outlets are distinguished by a stable cast housing and can be installed surface-mounted on the wall using the ORF 03 frame. The inner conductor is fastened with a contact screw and the outer conductor with a clamp. All components satisfy the Standard DIN EN 50083 – 2/-4. The following components are available as accessories for the OR series antenna outlets: Terminal resistor ORT 01, surface mount frame ORF 03 and cover plate ORC 02. Wideband sockets for trunk lines OR 02 Connectors DIN IEC female socket for Radio DIN IEC male socket for TV Frequency range 5 – 862 MHz Tap-loss TV 5 - 862 MHz Tap-loss Radio 87.5 – 139 MHz Return-loss 5 – 65 MHz 65 – 862 MHz OR 20 DIN IEC female socket for Radio, DIN IEC male socket for TV Connectors Frequency range Through-loss Wideband Stub cable outlet 5 – 470 MHz 470 – 862 MHz 2.2 dB 5.5 dB > 20 dB > 15 dB OR 15 OR 11 OR 09 DIN IEC female socket for Radio, DIN IEC male socket for TV DIN IEC female socket for Radio, DIN IEC male socket for TV DIN IEC female socket for Radio, DIN IEC male socket for TV 5 – 862 MHz 5 – 862 MHz 5 – 862 MHz 5 – 862 MHz 0.5 dB 0.8 dB 0.8 dB 1.0 dB 1.0 dB 1.3 dB 1.7 dB 2.1 dB Decoupling-loss TV 5 – 862 MHz 20.0 dB 15.0 dB 11.5 dB 9.5 dB Decoupling-loss Radio 5 – 139 MHz 22.0 dB 18.0 dB 15.0 dB 12.0 dB > 38 dB > 33 dB > 33 dB > 35 dB 5 – 65 MHz 65 – 862 MHz > 20 dB > 15 dB > 20 dB > 15 dB > 20 dB > 15 dB > 20 dB > 15 dB Directional-loss Return-loss 36 ANTENNA OUTLETS ORS series The ORS 03 and ORS 04 outlets can be used on stub cable and the ORS 13 DC can be used on loop-through in SAT distribution networks. They offer connection possibilities for one resp. two satellite receivers (ORS 04), radio receiver and TV. The 14 V/18 V converter feed voltage and 22 kHz switching signal are transferred over the SAT socket. The antenna outlets are distinguished by their stable cast housing and can be installed flush in VDE switch boxes or surface-mounted on the wall using the ORF 04 frame. The inner conductor is fastened with a contact screw and the outer conductor with a clamp. The cover plate has dimensions of 80 mm x 80 mm and is included with the outlet. Connectors ORS 03 ORS 04 DIN IEC male socket for TV DIN IEC female socket for RF F connector socket for SAT DIN IEC male socket for TV DIN IEC female socket for RF F connector socket for SAT Frequency range 40 – 2400 MHz 40 – 2400 MHz Tap-loss TV 1.0 dB (40 – 68 MHz) 1.5 dB (174 – 862 MHz) 1.5 dB (40 – 68 MHz) 1.5 dB (174 – 862 MHz) Tap-loss Radio 1.0 dB (87.5 – 125 MHz) Tap-loss SAT 1 2.0 dB (950 – 2150 MHz) 3.0 dB (2150 – 2400 MHz) Tap-loss SAT 2 - max. LNB current 500 mA 1.5 dB (87.5 – 125 MHz) 2.5 dB (950 – 2050 MHz) 4.0 dB (2050 – 2150 MHz) 8.0 dB (2150 – 2400 MHz) 1.5 dB (950 – 2050 MHz) 2.5 dB (2050 – 2150 MHz) 5.0 dB (2150 – 2400 MHz) 500 mA ORS 13 DC Connectors DIN IEC male socket for TV DIN IEC female socket for RF F connector socket for SAT Frequency range 4 – 2400 MHz Tap-loss TV 10.5-13.5 dB (4 – 68 MHz) 10.5-13.5 dB (109 – 470 MHz) 10.5-13.5 dB (470 – 862 MHz) Tap-loss Radio Tap-loss SAT Through-loss TV 10.5-13.5 dB (87.5 – 108 MHz) 10.5-13.5 dB (950 – 2050 MHz) 11.0-14.0 dB (2050 – 2200 MHz) 1.5 dB (4 – 68 MHz) 1.5 dB (109 – 470 MHz) 2.0 dB (470 – 862 MHz) Through-loss Radio 1.5 dB (87.5 – 108 MHz) Through-loss SAT 2.5 dB (950 – 2050 MHz) 3.0 dB (2050 – 2200 MHz) max. LNB current 500 mA 37 D I S H A N T E N N A S / AC C E S S O R I E S STA 1000 100 cm aluminium antenna. Suitable for projects with head-end station systems. Simple installation with wing nuts. Metal feed mount. Colour: STA 855 85 cm aluminium antenna. Suitable for multifeed reception (when additional multifeed mount STM 2 is installed). Simple installation with wing nuts. Metal feed mount. Colour: STA 755 Aluminium antenna with size of 74 cm x 84 cm. With reception reserves (e.g. during bad weather). Simple installation with wing nuts. Metal feed mount. Colour: STA 605 Aluminium antenna with size of 57 cm x 64 cm. Simple installation with wing nuts. Colour: Multifeed Mountings STM 1 and STM 2 colours anthracite The STM 1 (for plastic feed mounting) and STM 2 (for metal feed mounting) multifeed mountings offer reception possibilities for two satellites whose orbital position differs by approx. 6° (e.g. Astra 19.2° east and Eutelsat Hotbird 13° east). light grey brick-red Antenna STA 1000 STA 855 STA 755 STA 605 Size of reflector 1090 x 991 mm Ø 850 mm 740 x 840 mm 570 x 640 mm Gain 10.75/11.75/12.75 GHz 39.8/40.5/40.9 dBi 38.12/38.65/39.53 dBi 36.80/37.55/38.50 dBi 34.67/35.15/36.13 dBi Angle of beam < 1.8° < 2.2° < 2.2° < 2.9° Isolation of cross-polarisation > 27 dB > 27 dB > 27 dB > 27 dB Mounting of mast 32 – 76 mm 32 – 76 mm 32 – 50 mm 32 – 50 mm Max. elevation 5 – 90° 15° - 50° 15° - 50° 15° - 50° F/D ratio 0.55 0.6 0.6 0.6 Angle of offset 25° 21.5° 25° 25° 1) Wind load 268 kg 192.1 kg 156.2 kg 91.7 kg Mounting of feed Ø 23 and 40 mm Ø 23 and 40 mm Ø 23 and 40 mm Ø 23 and 40 mm 1) at a speed of wind by 216 km/h 38 On our homepage you will find the actual technical datas for the Antenna Outlets, Dish Antennas and Accessories. LNB Universal Single-LNB Universal Single-LNB GLS40 For reception of digital and analogue channels from satellites transmitting in the 11-GHz and 12-GHz frequency range. Input frequency range 10.7 – 11.7 GHz 11.7 – 12.75 GHz Frequency of oscillator 9.75 GHz 10.6 GHz Output frequency range 950 – 1950 MHz 1100 – 2150 MHz Gain typ. 52 – 64 dB Current supply typ. 110 mA Mounting of feed 40 mm Universal Twin-LNB Universal Twin-LNB GLT40 For connection of 2 receivers or one twin receiver for reception of digital and analogue channels in the 11-GHz and 12-GHz frequency range. Input frequency range 10.7 – 11.7 GHz 11.7 – 12.75 GHz Frequency of oscillator 9.75 GHz 10.6 GHz Output frequency range 950 – 1950 MHz 1100 – 2150 MHz Gain typ. 52 – 65 dB Current supply typ. 120 mA Mounting of feed 40 mm Universal Quattro-LNB Universal Quattro-LNB GLQ40 GLQ400 For multiple subscriber systems for simultaneous reception of digital and analogue channels from satellites transmitting in the 11-GHz and 12-GHz frequency range. Input frequency range 10.7 – 11.7 GHz 11.7 – 12.75 GHz 10.7 – 11.7 GHz 11.7 – 12.75 GHz Frequency of oscillator 9.75 GHz 10.6 GHz 9.75 GHz 10.6 GHz Output frequency range 950 – 1950 MHz 1100 – 2150 MHz 950 – 1950 MHz 1100 – 2150 MHz Gain typ. 50 – 65 dB 55 dB Current supply typ. 220 mA 200 mA Mounting of feed 40 mm 40 mm Universal Quad-LNB/ Universal Oct-LNB Universal Quad-LNB/ Universal Oct-LNB GLOT40 GLQD40 For connection of 4 resp. 8 receivers for reception of digital and analogue channels from satellites transmitting in the 11-GHz and 12-GHz frequency range. Input frequency range 10.7 – 11.7 GHz 11.7 – 12.75 GHz 10.7 – 11.7 GHz 11.7 – 12.75 GHz Frequency of oscillator 9.75 GHz 10.6 GHz 9.75 GHz 10.6 GHz Output frequency range 950 – 1950 MHz 1100 – 2150 MHz 950 – 1950 MHz 1100 – 2150 MHz Terrestrial input - - No. of outputs 8 4 Gain typ. 50 – 65 dB 50 – 65 dB Current supply typ. 210 mA 210 mA Mounting of feed 40 mm 40 mm 39 On our homepage you will find the actual technical datas for the LNBs. Wall holder WAH 25 Wall holder for SAT antennas from aluminium Length 250 mm, Height 250 mm WAH 35 Wall holder for SAT antennas from aluminium Length 350 mm, Height 250 mm WAH 45 Wall holder for SAT antennas from aluminium Length 450 mm, Height 250 mm WSH 28 Wall holder for SAT antennas from steel Length 280 mm, Height 300 mm WSH 40 Wall holder for SAT antennas from steel Length 400 mm, Height 300 mm WSH 50 Wall holder for SAT antennas from steel Length 500 mm, Height 300 mm 40 INSTALL ATION M ATER I A L Accessories for roof installation RMFR Frankfurt pan from plastic, red, for mast installation RMFB Frankfurt pan from plastic, black for mast installation RMPB Lead pan incl. lead-through for cables, for mast installation RMS 60 Mast boot (sealing grommet), black 42/48/60 RM 9 Rafter holder, adjustable for widths of rafters from 56 cm to 92 cm, length of mast 92 cm, diameter of mast 48 mm RME 50 extension for rafter holder RM9, length 50 cm RMT 80 Rhepanol sealing tape, up to 80 mm 41 Compression gripper GCG 1000 Compression gripper for F compression connectors and IEC compression connectors, for Mini, Midi and standard coaxial cables, suitable for F compression connector FCC 70 Wire stripping tool GWS 1000 Wire stripping tool for coaxial cables 7mm, RG 6 for 6/7mm F connectors Connecting cable CCQ 150 HF connecting cable, with Quick-F connector at both sides, Length 1.50 m CCQ 250 HF connecting cable, with Quick-F connector at both sides, Length 2.50 m CCI 150 HF connecting cable, with IEC male connector and IEC female connector, Length 1.50 m 42 INSTALL ATION M ATER I A L Connectors FCC 70 F compression connector, for coax cable with a diameter of 7.0 mm FCW 70 F-connector, screwable, waterproof for coax cable with a diameter of 7.0 mm FC 70 F connector, screwable, for coax cable with a diameter of 7.0 mm FC 60 F connector, screwable, for coax cable with a diameter of 6.0 mm FC 50 F connector, screwable, for coax cable with a diameter of 5.0 mm FCF 70 F connector, female–female FCF 360 F connector, female–female, U-form FQQ 70 F connector, Quick male–Quick male FIM 70 F connector, F connector–IEC male FIF 70 F connector, F connector–IEC female FT 75 F terminator, 75 Ohms FTD 75 F terminator, 75 Ohms, DC decoupled FQF 70 Adaptor from Quick male to F connector ICM 100 IEC connector male, screwable, for coax cable with a diameter up to 7.0 mm ICF 100 IEC connector female, screwable, for coax cable with a diameter up to 7.0 mm 43 da kapo Your GSS System Partner: Printed in Germany We cannot assume any liability for the technical data specified here. Delivery subject to availability. GSS Grundig SAT Systems GmbH Beuthener Strasse 43 D-90471 Nuernberg Phone: +49/911/703-8877 Fax: +49/911/703-9210 [email protected] www.gss.de