Download SLV-E830B/E830NP/E830VC1/E830VC2 RMT

SLV-E830B/E830NP/E830VC1/E830VC2
RMT-V224/V224B
SERVICE MANUAL
French Model
SLV-E830B
Spanish Model
SLV-E830NP
Germany Model
SLV-E830VC1/E830VC2
G
j
• Refer to the SERVICE MANUAL of VHS MECHANICAL
ADJUSTMENTS for MECHANICAL ADJUSTMENTS.
(9-921-647-11)
S MECHANISM
SPECIFICATIONS
VIDEO CAMERA RECORDER
MICROFILM
FEATURE DIFFERENCE
MODEL NAME (SLV-)
E830VC1
E830VC2
E830NP
®/®
SAFETY SECAM (REC/PB)
G/®
ME-SECAM (REC/PB)
¢
ACS (¢: ACA)
TUNER (BTF-)
¢
3WC402
SYSTEM 1
STEREO
E830B
®
®
WC411
3WC443
BG
BG
BG
L
ZWEI
ZWEI
N/Z
NI
SYSTEM 2
BG
STEREO
RF OUT SYS
REMOTE COMMANDER (RMT-)
ZWEI
G
G
G
L/G
V224
V224
V224
V224B
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE WITH
MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
1.
2.
3.
Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes
and bridges.
Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
4.
Look for parts which, through functioning, show obvious signs
of deterioration. Point them out to the customer and
recommend their replace-ment.
5. Check the B+ voltage to see it is at the values specified.
6. Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
—2—
TABLE OF CONTENTS
SERVICE NOTE
1.
ERROR CODE INDICATION ··········································· 5
1.
GENERAL
Getting Started
Unpacking ·············································································· 1-1
Setting up the remote commander ········································· 1-1
Connecting the VCR ······························································ 1-2
Tuning your TV to the VCR ······················································ 1-3
Setting up the VCR with the Auto Set Up function ··············· 1-4
Setting the clock ···································································· 1-4
Manual setup — Selecting a language ··································· 1-5
Manual setup — Presetting channels ····································· 1-6
Manual setup — Setting station names ································· 1-6
Manual setup — Changing/disabling programme positions · 1-7
Manual setup — Listing the channels as the TV ··················· 1-8
Connecting the Satellite tuner ················································ 1-8
Setting the PAY-TV/Canal Plus decoder ································ 1-9
Basic Operations
Playing a tape ······································································· 1-10
Recording TV programmes ················································· 1-10
Recording TV programmes using ShowView ····················· 1-11
Setting the timer manually ··················································· 1-12
Additional Operations
Playing/searching at various speeds ···································· 1-13
Recording TV programmes using the quick timer ·············· 1-14
Checking/changing/cancelling timer settings ······················ 1-14
Recording stereo and bilingual programmes ······················· 1-15
Searching using the index function ······································ 1-15
Adjusting the picture ··························································· 1-15
Changing options ································································· 1-16
Editing
Connecting to a VCR or stereo system ································ 1-16
Basic editing ········································································ 1-17
Audio dubbing ····································································· 1-17
Additional Information
Index to parts and controls ··················································· 1-17
2.
DISASSEMBLY
2-1.
2-2.
2-3.
2-4.
UPPER CASE, FRONT PANEL BLOCK ASSEMBLY · 2-1
FR-128 BOARD, DM-73 BOARD ································· 2-1
REAR PANEL ································································· 2-1
POWER BLOCK, MA-316 BOARD
(WITH S MECHANISM DECK) ··································· 2-2
2-5. RP-231 BOARD, S MECHANISM DECK ···················· 2-2
2-6. INTERNAL VIEWS ························································ 2-3
2-7. CIRCUIT BOARDS LOCATION ··································· 2-4
3.
BLOCK DIAGRAMS
3-1.
3-2.
3-3.
3-4.
3-5.
3-6.
3-7.
OVERALL BLOCK DIAGRAM ···································· 3-1
VIDEO BLOCK DIAGRAM ·········································· 3-3
SERVO/SYSTEM CONTROL BLOCK DIAGRAM ····· 3-5
AUDIO BLOCK DIAGRAM ·········································· 3-7
MODE CONTROL BLOCK DIAGRAM ······················· 3-9
TUNER BLOCK DIAGRAM ······································· 3-11
POWER SUPPLY BLOCK DIAGRAM ······················· 3-13
4.
PRINTED WIRING BOARDS AND
SCHEMATIC DIAGRAMS
4-1. FRAME SCHEMATIC DIAGRAM ································ 4-1
4-2. PRINTED WIRING BOARDS AND
SCHEMATIC DIAGRAMS ············································ 4-3
• RP-231 (REC/PB AMP)
PRINTED WIRING BOARD ························· 4-3
• RP-231 (REC/PB AMP) SCHEMATIC DIAGRAM ···· 4-5
• MA-316 (VIDEO, SERVO/SYSTEM CONTROL,
AUDIO, TUNER)
PRINTED WIRING BOARD ························· 4-8
• MA-316 (VIDEO, NORMAL AUDIO)
SCHEMATIC DIAGRAM ···························· 4-11
• MA-316 (SERVO/SYSTEM CONTROL)
SCHEMATIC DIAGRAM ·········································· 4-14
• MA-316 (ON SCREEN DISPLAY)
SCHEMATIC DIAGRAM ···························· 4-17
• MA-316 (AFM AUDIO) SCHEMATIC DIAGRAM · 4-19
• MA-316 (TUNER) SCHEMATIC DIAGRAM ·········· 4-21
• MA-316 (FOLLOW TV, PDC, VPS)
SCHEMATIC DIAGRAM ···························· 4-23
• MA-316 (I/O) SCHEMATIC DIAGRAM ·················· 4-25
• FR-128 (MODE CONTROL)
PRINTED WIRING BOARD ······················· 4-29
• FR-128 (MODE CONTROL)
SCHEMATIC DIAGRAM ···························· 4-31
• SE-69 (SECAM VIDEO SIGNAL PROCESS)
SCHEMATIC DIAGRAM ···························· 4-33
• SE-69 (SECAM VIDEO SIGNAL PROCESS)
PRINTED WIRING BOARD ······················· 4-35
• DM-73 (OPERATION SWITCHES)
PRINTED WIRING BOARD ······················· 4-36
• DM-73 (OPERATION SWITCHES)
SCHEMATIC DIAGRAM ···························· 4-37
• POWER BLOCK SR826 (SWITCHING REGULATOR)
PRINTED WIRING BOARD ······················· 4-39
• POWER BLOCK SR826 (SWITCHING REGULATOR)
SCHEMATIC DIAGRAM ···························· 4-41
5.
INTERFACE,
IC PIN FUNCTION DESCRIPTION
5-1. SYSTEM CONTROL —
VIDEO BLOCK INTERFACE
(MA-316 BOARD IC160) ··············································· 5-1
5-2. SYSTEM CONTROL —
SERVO PERIPHERAL CIRCUIT INTERFACE
(MA-316 BOARD IC160) ··············································· 5-1
5-3. SYSTEM CONTROL —
MECHANISM INTERFACE
(MA-316 BOARD IC160) ··············································· 5-2
5-4. SYSTEM CONTROL —
SYSTEM CONTROL PERIPHERAL CIRCUIT
INTERFACE (MA-316 BOARD IC160) ························ 5-2
5-5. SYSTEM CONTROL —
AUDIO BLOCK INTERFACE
(MA-316 BOARD IC160) ··············································· 5-2
5-6. SERVO/SYSTEM CONTROL MICROPROCESSOR
PIN FUNCTIONS (MA-316 BOARDS IC160) ·············· 5-3
5-7. TUNER/TIMER MODE CONTROL PIN FUNCTIONS
(FR-128 BOARD IC180) ················································ 5-4
6.
ADJUSTMENTS
6-1. MECHANICAL ADJUSTMENTS ································· 6-1
6-2.. ELECTRICAL ADJUSTMENTS ··································· 6-1
2-1. PREPARATION BEFORE ADJUSTMENT ··················· 6-1
2-1-1. Equipment Required ························································ 6-1
2-1-2. Equipment Connection ···················································· 6-1
2-1-3. Input Signal Check ·························································· 6-1
2-1-4. Alignment Tape ······························································· 6-1
2-1-5. Input/Output Levels and Impedance ······························· 6-2
2-1-6. Adjustment Sequence ······················································ 6-2
2-2. POWER SUPPLY CHECK ············································· 6-2
2-2-1. Output Voltage Check (MA-316 Board) ························· 6-2
2-3. SERVO SYSTEM CHECK ············································· 6-2
—3—
2-3-1. RF Switching Position/
AF Switching Position Adjustments
(MA-316, RP-231 Boards) ·············································· 6-2
2-4. VIDEO SYSTEM CHECKS ··········································· 6-3
2-4-1. X’tal OSC Check (MA-316 Board) ································· 6-3
2-4-2. SYNC AGC Check (MA-316 Board) ······························ 6-4
2-4-3. White Clip/Dark Clip Check (MA-316 Board) ··············· 6-4
2-4-4. Recording Y Level Check (MA-316 Board) ··················· 6-4
2-4-5. Recording Chroma Level Check (MA-316 Board) ········· 6-4
2-4-6. Playback Level Check (MA-316 Board) ························· 6-5
2-5. AUDIO SYSTEM ADJUSTMENT ································· 6-5
2-5-1. ACE Head Adjustment ···················································· 6-5
2-5-2. E-E Output Level Check ················································· 6-5
2-5-3. Overall Output Level and Distortion Factor Check ········· 6-5
2-5-4. Overall Noise Level Check ·············································· 6-5
2-6. ADJUSTMENT PARTS LOCATION DIAGRAM ········· 6-6
7.
REPAIR PARTS LIST
7-1. EXPLODED VIEWS ······················································ 7-1
7-1-1. FRONT PANEL ASSEMBLY AND
UPPER CASE SECTION ··············································· 7-1
7-1-2. CHASSIS SECTION ······················································· 7-2
7-1-3. MECHANISM DECK-1 ················································· 7-3
7-1-4. MECHANISM DECK-2 ················································· 7-4
7-1-5. MECHANISM DECK-3 ················································· 7-5
7-2. ELECTRICAL PARTS LIST ·········································· 7-6
—4—
SLV-E830B/E830NP/E830VC1/E830VC2
SERVICE NOTE
1.
ERROR CODE INDICATION
• Error codes are indicated using the lower 5 digits in the fluorescent display tube.
“At this time, Colon “:” between character is not indicated.”
Mode code indication when the error has occurred.
Error code
ERROR CODE
0 No error
1 Cam encoder error Loading direction
2 Cam encoder error Unloading direction
3 T reel error
4 S reel error
5 Capstan error
6 Drum error
7 Error on initializing
8 Cassette loading error
9 Reserve
MODE CODE
0 Power-on eject
1 Power-on initial
2 Power-off eject
3 Power-off stop
4 FF
5 REW
6 REC
7 REC- pause
8 Power-on stop
9 PB
10
11
12
13
14
15
16
17
18
19
FWD x1
FWD x2
CUE
PB-pause
RVS-pause
RVS x1
RVS x2
REV
Power-off initial
Mecha. error (Power off)
—5—
20
21
22
23
24
25
26
27
28
REW play
Cas. loading
Tape loading
Power-off loading
Mecha. error (Power on)
Power-on eject initial
Power-off eject initial
APC REC
Cas. loading
(No auto PB check)
SLV-E830B/E830NP/E830VC1/E830VC2
SECTION 1
This section is extracted
GENERAL
from instruction manual.
1-1
1-2
1-3
1-4
1-5
1-6
1-7
1-8
1-9
1-10
1-11
1-12
1-13
1-14
1-15
1-16
1-17
1-18E
SLV-E830B/E830NP/E830VC1/E830VC2
SECTION 2
DISASSEMBLY
NOTE : Follow the disassembly procedure in the numerical order given.
2-1. UPPER CASE, FRONT PANEL BLOCK ASSEMBLY
1 Screws (case)
Upper case
3 Connector
From CN161 on
MA-316 board
2
4 Hooks
1 Screws (case)
3 Flat cable
From CN164 on
MA-316 board
5 Front panel
block assembly
4 Hooks
4 Hooks
2-2. FR-128 BOARD, DM-73 BOARD
3 Flat cable
From CN181 on
FR-128 board
2 FR-128 board
1 Screws
3 Connector
From CN480 on
FR-128 board
1 Screws
2 DM-73 board
Front panel assembly
3 Frexible board
From CN451 on
DM-73 board
3 Flat cable
From CN400 on FR-128 board
or CN452 on DM-73 board
2 Hooks
2-3. REAR PANEL
2 Hooks
2 Hooks
3 Rear panel
2 Hooks
1 Release cable stopper
from rear panel
1 Release harness from
hooks on rear panel
2-1
2-4. POWER BLOCK, MA-316 BOARD (WITH S MECHANISM DECK)
Connector
(From CN101 on power block)
2 Screws
a
3 Power block
1
4 Screws
5 MA-316 board
(with S mechanism deck)
1
a
2-5. RP-231 BOARD, S MECHANISM DECK
1 Connector
From CN302 on
RP-231 board
2 Screws
1 Flexible board
From CN260 on
RP-231 board
1 Connector
From CN301 on
RP-231 board
4 Screws
3 RP-231 board
S mechanism deck
5
MA-316 board
MD base (L)
MD (M) base
MD base (R) (LS)
2-2
2-6. INTERNAL VIEWS
—Top View—
M901
Drum assembly
DZH-86A-R
1-759-373-11 (NP/VC1/VC2)
DZH-98A-R
1-759-557-11 (B)
ACE head block assembly
A-6759-620-A
Pinch press block assembly
A-6759-615-A
FE head
1-500-144-11
FL complete assembly
A-6759-619-C
Reel (T) table
3-977-508-01
Reel (S) table
3-977-507-01
—Bottom View—
M902
DC motor (capstan)
1-698-971-11
M901
Drum assembly
DZH-86A-R
1-759-373-11 (NP/VC1/VC2)
DZH-98A-R
1-759-557-11 (B)
Rubber belt
3-977-510-01
M903
Cam motor assembly
X-3947-577-1
2-3
2-7. CIRCUIT BOARDS LOCATION
MA-316
VIDEO, AUDIO,
SERVO/SYSTEM CONTROL,
TUNER
RP-231 (REC/PB AMP)
SE-69 (SLV-E830B)
SECAM VIDEO SIGNAL
PROCESS
FR-128
(MODE CONTROL)
POWER BLOCK
DM-73
(OPERATION SWITCHES)
2-4E
SLV-E830B/E830NP/E830VC1/E830VC2
SECTION 3
BLOCK DIAGRAMS
3-1. OVERALL BLOCK DIAGRAM
MD BLOCK
RP-231 BOARD
MA-316 BOARD
(SEE PAGE 4-5)
IC661
IC201 (1/2)
(SEE PAGES 4-11, 14, 17, 19, 21, 23, 25)
VIDEO
PB RF
SP
CH1
IC260
VIDEO
REC/PB
AMP
IC202
IC660
1H
OSD
C SYNC
Y/C 1
EP
CH1
D VS
CS
CG V
DELAY
DRUM
SERVO
D PG
DRUM
PG
BUFF
D FG
DRUM
FG
B MODEL ONLY
OSD V
SE-69 BOARD (SEE PAGE 4-33)
MESECAM
Q VD
M
Q662
Y/C 3
CLOCK(SSB)
EP
CH2
MOTOR
IC100
OSD S
Y/C 2
DATA(SSB)
DRUM MOTOR
DRUM
M901
IC160 (2/2)
H DET
S CLK
Y/C
PROC
C ROT
SP
CH2
AFC
REC RF
NT JUDGE
RF SWP
RF ENV
PB C
PB C
IC970
PB RF
REC C
(SEE PAGE 4-31)
C SYNC
CAPSTAN
SERVO
CAPSTAN
MOTOR
IC850
J480
PDC/DAV
L2 V
VIDEO
VPS/PDC
SDA
DECODER
SCL
C FG
JS544
VIDEO
LINE 2 IN
CAPSTAN
FG
IC141
IC140
PB CTL
CTL
HEAD
Y/C 3
CTL RST
CN570
OSD V
SDA
CN500
7
I
16
V IN
20
V OUT
19
AV CONT
8
RF AGC
AFT
SW2
PLL ENABLE
SW1
PLL CLOCK
PLL DATA
SCL
SDA
RF AGC
AFT
SW2
PLL ENABLE
SW1
PLL CLOCK
PLL DATA
SCL
(SEE PAGE 4-5)
TU701
OUT
TU V
FOLLOW TV
PROC.
TU M
B
RP-231
BOARD
IN
TU L
11
UHF/
VHF
TU702
RF
OUT
TU R
G
IC820
RFU 750
V DET
15
NP MODEL
TU M
R
UHF/
VHF
MOD V
LINE 1
(TV)
IN
SCL
TU R
7
SDA
11
B
MOD V
V DET
G
Q510
BUFF
TU L
15
SCL
16
SDA
I
R
MOD A
8
C+ DET
REC CTL
IC540
C+ VIDEO
I/O SEL
C+ DET
TV/VTR
20
19
JS542
V IN
V OUT
DECODER/
LINE 3
M902
M
SECAM DET
VIDEO
FR-128
BOARD
CAPSTAN MOTOR
IC100
C VS
SECAM ON
SECAM
PROC
AV CONT
EXCEPT NP MODEL
FR-128 BOARD
(SEE PAGE 4-31)
CN570
A(L) IN
6
A(R) IN
DECODER/
LINE 3
A(L) OUT
3
A(R) OUT
1
IC182
2
IC160 (1/2)
CONTROL
A(L) IN
6
2
A(L) OUT
3
A(R) OUT
1
AV LINC
10
H DET
PDC/DAV
DATA (SSB)
CLOCK (SSB)
RF SWP
MODE CONT
FOLLOW TV
SDA
RF ENV
TUNER/
TIMER/
MODE
CONTROL
IC183
POWER
FAIL DET
SCL
C SYNC
PLL DATA
RESET
PULSE GEN
PLL CLOCK
PLL ENABLE
L
R
BS C+L
(SEE PAGE 4-31)
J480
DISPLAY
IC180
CG V
RF AGC
J500
(FRONT)
FLUORESCENT
CS
SW2
Q VD
AUDIO
LINE 2 OUT
FLD
DRIVER
EEPROM
SW1
SYSTEM
CN500
A(R) IN
ND4420
AV CONT
C+ DET
LINE 1
(TV)
IC420
MESECAM
NT JUDGE
PH101
SECAM ON
1L
FR-128 BOARD
S411
Q101
T SENS
1R
1L
IC400
REMOTE
CONTROL
RECEIVER
SECAM DET
S REEL
FG
MOD A
BS C+R
PH100
T REEL
FG
S CLK
S CLK
S IN
S OUT
S OUT
AD0
S400
S IN
STANDBY
L
AUDIO
LINE 2 IN
1R
R
POWER
SAVE
ASURA RESET
DEC L
1L
IC360
1R
AUDIO
PROC
(HIFI)
ASURA RESET
DEC R
Q100
S SENS
TU L
ASURA CS
ASURA CS
S401,402,404
406,408
TU R
AD1,2
AV LINC I/O
IC340
TU M
AFM PB
CH1
S101
REC
PROOF
IC201
AFM REC
(2/2)
AF SWP
AF ENV
REC
AF SWP
CH2
AF REC P
AFM
REC/PB
AMP
NORM IN
NORM OUT
DATA (IIC)
AUDIO
PROC
(MONO)
DATA (IIC)
CLOCK (IIC)
AD4,5
DMS1,2
S160
NTSC
PR SW
CLOCK (IIC)
DATA (IIC)
CLOCK (IIC)
HEAD PB
AUDIO
REC/PB
HEAD
AUDIO
ERASE
HEAD
IC301
HEAD
SW
X
NA REC
IC161
T321,Q321
FULL
ERASE
HEAD
BIAS
ERASE
OSC
X
REC
BIAS VCC
AF REC P
AF SWP
FULL ERS
FULL ERS
AF ENV
T331,Q331
BIAS
ERASE
OSC
RP-231 BOARD
(SEE PAGE 4-5)
LOADING
MOTOR
DRIVE
MODE1-4
M
LOADING
MOTOR
CAM
ENCODER
AV LINC
I/O BUFF
16
3-1
3-2
FUNCTION
KEY
DM-73 BOARD
(SEE PAGE 4-37)
S451,453
457-459
DMS
BLOCK
FUNCTION
KEY
SHUTTLE
SWITCH
SLV-E830B/E830NP/E830VC1/E830VC2
3-2. VIDEO BLOCK DIAGRAM
MA-316 BOARD
(SEE PAGE 4-11, 17, 23)
B MODEL ONLY
IC201 #∞ REC
Q662
Q660,661
BUFFER
SECAM
MIX
IC201 #• REC
Q663
(SEE PAGE 4-31)
IC201
FR-128
BOARD
Y/C 1
CN480
Y/C 2
5
TU701 18
FROM/TO
TUNER
BLOCK
TU702 32
RFU750
V IN
V OUT
CN570
CLP
30
CLP
33
SW5V
20
2
Y/C 3
TU V
MOD V
IC540
C+ VIDEO/ I/O SEL
6
(SEE PAGE 3-11, 12)
12
8
I
16
R
15
G
11
B
7
8
Q540
CLP
4
CLP
VIDEO
AMP
QH/QV
INS
P
BUFFER
38
2
R
SUNC
SEP
37
2
3
Y/C
MIX
P
P
1
SW2
2
Q510
6dB
H
16
1
7
SEP
CLP
40
Y NR
42
5
NT 43
12
P
DET 8
H SUNC 12
9 HD
V SYNC 13
5 VD
CN164 10
CG V
CN164 30
OSD S
CN164 26
X661
S IN 23
S CLK 22
BUFFER
7
H DET
FROM/TO
SYSCON
BLOCK
(SEE PAGE 3-6)
VCO O 11
V SYNC 11
9 XS
5.5Vp-p
1H
DL
CS 24
OSD SCLK
Q613
OSD CS
CN164 18
R
IC201 $∞ PB
CLK 10
4.2Vp-p
66 C ROT
BUFFER
CN164 21
VCO I 10
8 EXS
Q209
R
IC201 #¶ REC/PB
3
3 V IN
IC660 8 REC/PB
X660
17.73MHz
6dB
CN600 11
25 V OUT
Q664
17.73MHz
SW1
4
CLP
6
R
2.4Vp-p
H
L206
CLP
PW CONT 1
4
2 VIDEO
OSD
5
CLP
19
C+ DET
32
IC660
L204
C VCC 47
VIDEO
AGC
35
IC160 71
AFC
IC660 @∞ REC/PB
Y VCC 36
34
IC160
SECAM MIX
IC661
2.4Vp-p
H
CN161
5
DECODER/
LINE 3
28
1Vp-p
H
JS542
L2 V
VIDEO
LINE2 IN
JS544
(FRONT) J480
(1/2)
Y/C PROCESSOR
QVD
IC202
(1/2)
H
4
-6dB
10
CN500
R
15
G
11
B
7
I
16
V IN
20
LINE 1
(TV)
V OUT
19
AV CONT
8
SW3
3
15
2
1
FSC
BPF
SCL 11
9
IC201 !∞ PB
IC201 ^º REC/PB
IC202
0.1µsec/div
0.2V/div
5
3
IC820
7
FOLLOW TV
PROCESSOR
1
Q820,821
R
BUFFER
R
FOLLOW TV IC160 57
Q501,502
AV
CONT.
C+ DET
IC160 17
AV CONT
IC160 16
ACC
AMP
P
R
FROM/TO
SYSCON
BLOCK
(SEE PAGE 3-6)
P
MAIN
COMV.
DL
EQ
BPF
R
15
1
48
3
Q210
1H
DL
17
N
PB
EQ
KIL
16
14
FM
AGC
N
BUFFER
3
3
SP
CH1
VIDEO REC/PB AMP
2
B
VXO1
56
55
CLP
60
X201
Q211
BUFFER
REC RF
REC
EQ
FM
MOD
H
0.34Vp-p
ACK OUT 62
DE
EMPH.
SECAM DET 65
NT JUGE
IC160 13
MESECAM
IC160 14
C
TRAP
16
H
L262
0.42Vp-p
5
7
SP
CH2
R,A
P
58
18
29
PB
0.6Vp-p
IC201 $• REC
IC201 @∞ REC
IC201 !¢ REC
L263
SW7 SW3
4
R
59
TRAP
4.43MHz
L206
20
H
SW5V
IC260
26
SW5V
P
52
VXO2
440mVp-p
PB
R
BUFFER
DEM
RP-231 BOARD
CN260
13
DE
EMPH.
25
P
S
Q1352
SEQ
PB Y/C
50
(2/2)
Q208
C
LPF
P
S
DRUM
VIDEO
HEAD
46
75mVp-p
H
SDA
470mVp-p
45
IC201 !∞ REC
6dB
6
CN272
HPF
SW8 SW4
8
ENV
DET
CN306
26
7
7
17
6
6
19
5
5
20
4
4
18
3
3
PB
13
5
EP
CH1
RF SWP
14
COMP
PB
11
1
EP
CH2
10
CLOCK
C SYNC
C ROT
SW9 SW5
2
LOGIC
DATA
SW10 SW6
6
CN271
21
REC
IDEL
4
CN970
3
PB RF
22
SCL
BUFFER
13
1 CTL
12
0.2µsec/div
0.1V/div
VCA
REC RF
11
28
BUFFER
11
LIM
Q974
Q201
SW2
9
REC C
BUFFER
9
2.2M
TRAP
11
REC
MUTE
CN261
1
CHECK
PIN
CN261 1 PB
2
5
PB RF
CN272
AV ADJ
AV ADJ
11
CN306
8
R
1.1M
BPF
CN307
IC260 @• REC
0.1V/div
0.1µsec/div
CN261 2 REC/PB
IC160 66
C SYNC
IC160 81
CLOCK (SSB)
IC160 80
DATA (SSB)
IC160 1
RF SWP
IC160 60
RF ENV
FROM/TO
CN164 13
SYSCON
BLOCK
CN164 14
(SEE PAGE 3-6)
5Vp-p
2
PB RF
11
LPF
13
C SYNC
7
27 C SYNC
CN970
SYNC
GATE
1/4
R
R
4.3M
BPF
4.3M
A BELL
4
2
P
2.2M
BPF
4.3M
BELL
PB
MUTE
17
2.2M
TRAP
BUFFER
Q970
Q975,976
4.3M
BELL
SWITCH
6
PB C
6
X2
SYNC
GATE
R
IC970
SECAM
PROCESSOR
SECAM VIDEO
P
21
P
SECAM
DET
26
SDA
SCL
IC850
5 SDA
4 SCL
PDC DAV
9 DAVN
D5V
VDDA 20
VDDD 19
CVBS 17
Q850
BUFFER
16
3-3
SECAM ON IC160 26
Q973
X2
AGC
AMP
FSC
5
1
PB 3V
SECAM DET
5
1
B MODEL ONLY
VPS/PDC DECODER
CN164 31
CN307
3
AV ADJ
IC160 56
2mV/Div
0.2µsec/div
4
P
8
7
25Hz
1.1M
BELL
1.1M
A BELL
RF SWP
2
15
13
SW1
REC
SECAM ON
15
Q260
REC
IC260 4 REC
(SEE PAGE 4-33)
Q972
CN305
15
SE-69 BOARD
SW5V
3-4
SECAM DET IC160 12
FROM
SYSCON
BLOCK
(SEE PAGE
3-6)
SLV-E830B/E830NP/E830VC1/E830VC2
3-3. SERVO/SYSTEM CONTROL BLOCK DIAGRAM
MA-316 BOARD
IC160 1, 100 REC/PB
(SEE PAGE 4-14)
IC160
IC100
DRUM MOTOR
M901
CN101
VCC
OUTPUT
CN101 3 REC/PB
M
1
2
2
(1/2)
SERVO CONT
DRUM ERR INTEG
MTR12V
D VS
7
+
–
5
(2/2)
SYSTEM CONTROL
(1/2)
6
5Vp-p
25Hz
REF 2.5V
74
D160
L161
D6V
DRUM DA
OUTPUT
CN306 12
HALL
DEVICE
25Hz
1
IC160
MATRIX
TO/FROM
AUDIO
BLOCK
5Vp-p
3
PG
3
IC360
D PG
68
DRUM PG
IC360
41
42
CN101 4 REC/PB
4
53
AVREF
89
VDD
90
5V
AF ENV
IC360
39
AF ENV
59
IC360
40
AF SWP
100 AF SWP
CN306 13
REC
96
REC
CN306 14
AF REC P
2
AF REC P
CN305
6
FULL ERS
36
FULL ERS
IC201
64
DATA (IIC)
28
SDA 0
IC201
63
CLOCK (IIC)
30
SCL 0
IC201
70
A MUTE
31
A MUTE
4
D FG
69
64
T REEL FG
DATA (SSB)
CN306
5
81
CLOCK (SSB) CN306
4
1
RF SWP
CN306
6
RF ENV
60
RF ENV
CN306
CAPSTAN MOTOR
M902
56
AV ADJ
CN306
8
66
C SYNC
IC201
37 ,CN306 3 ,CN307 7
Q VD
4
Q VD
IC201
33
MESCAM
14
MESCAM
IC201
65
NT JUDGE
13
NT JUDGE
IC201
62
1
SECAM DET
12
SECAM DET
CN307
SECAM MIX
71
SECAM MIX
Q660,661
SECAM ON
26
SECAM ON
CN307
AV CONT
16
AV CONT
Q501,502
C+ DET
17
C+ DET
CN570
FOLLOW TV
Q820,821
FOLLOW TV 57
PH100
T REEL
FG
MTR12V SW5V
3
TO/FROM
VIDEO
BLOCK
8
OSD S
IC660
23
OSD S CLK
IC660
22
OSD CS
IC660
24
CG V
IC660
11
H DET
IC661
8
PW CONT1
Q663
PDC DAV
SW5V
CN102
7
VM
HALL
DEVICE
7
AV ADJ
C SYNC
DRUM FG
SW12V
5Vp-p
AVDD
80
RF SWP
(SEE PAGE 3-8)
FG
300Hz
54
DATA (SSB)
CLOCK (SSB)
63
PS130
S REEL FG
IC850
9
SDA
IC540
9 ,IC850
5
SCL
IC540
11 ,IC850
4
7
U+
VCC
1
1
U–
TL
6
6
LIMITER
84
CAP TRQ PWM
V+
99
STEP PLS
V–
35
CAP STOP
(SEE PAGE 3-3, 4)
PH101
S REEL
FG
CN600
POWER SAVE CONT
POWER SAVE CONT 23
W+
IC100
(1/2)
CAP ERR INTEG
W–
D107
U
5
5
C VS
1
+
–
V
W
2
2
3
61
2
73
CAP RVS
72
CAP DA
POWER CONT2
Q101
TAKE END
SENSOR
D6V
REF 2.5V
T SENS
3
3
CAP FG
70
CN164
CAP RVS
S SENS
OSD SCLK
Q100
SUPPLY END
SENSOR
OSD S IN
POWER CONT2
POWER CONT1
LED
DRIVE
CAP FG
32
T/E LED
SCL
PDC DAV
IC160 7 REC/PB
S101
H DET
15
REC
PROOF
5Vp-p
758Hz
42
7
9
REC CTL
S160
3
7
2
7
CTL
REC/PB AMP
7
67
EXTAL
47
S IN 0
45
S OUT 0
46
ASURA RESET
S CLK
S OUT
S IN
ASURA RESET
40
ASURA CS
44
GAIN
SWITCH
92
TU ENABLE
AFT
55
NT PB SW
LANC IN
LANC OUT
ON PAL
TV
4Vp-p
16MHz
Q141
5
PLL CLOCK
NTSC
4.43
NTSC
PB SW
PB CTL
CTL
HEAD
4
43
XTAL
ASURA CS
IC141
CTL AMP
FOR
CHECK
X160
16MHz
IC160 $™ REC/PB
CN302
1
CG V
PLL DATA
IC140
26
22
21
14
31
30
25
24
23
19
20
17
16
15
9
11
12
CN165
2
CTL GAIN
3
CN261
CTL
8
8
8
D6V
HYS HIGH
IC160 ^¶ REC/PB
IC161
LOADING
MOTOR DRIVE
SCL
TU701 19
TU702 33
RFU750
6
SDA
TU701 20
TU702 34
RFU750
7
8
VCC1
AFT
TU701 10
TU702 24
9
VCC2
TU ENABLE
TU701
6
TU702 15
PLL CLOCK
TU701
4
TU702 13
1
2
CAM–
IN1
3
PLL DATA
TU701
5
TU702 14
3
10
CAM+
IN2
4
D131
MTR12V
CN104
LOADING
MOTOR
(
5Vp-p
4
3
)
2
1
MODE1
MODE2
9
CAM2
22
|
19
MODE1
|
MODE4
AUTO PRESET
5
AUTO PRESET
Q703
SW1
18
SW1
TU701 21
TU702 35
SW2
51
SW2
TU701 22
TU702 36
MOD CONT
25
MOD CONT
Q751,752
(SEE PAGE 3-11)
MODE3
MODE4
16
3-5
TO
TUNER
BLOCK
M
S100
CAM
ENCODER
MECHA
POSITION
25Hz
TO/FROM
MODE
CONTROL
BLOCK
FR-128 BOARD
CN181
10
(SEE PAGE 3-9)
4Vp-p
25Hz
CN305
9
6
REC PRF
S CLK
CN271
27
13
CN102 3, IC160 &º
REC/PB
(SEE PAGE 4-5)
18
Q613
62
SDA
RP-231 BOARD
TO
POWER BLOCK
11
13
OSD CS
D102
T/S LED
Q102
CAPSTAN
FG
17
POWER CONT1
3-6
4
CHECK
PIN
SLV-E830B/E830NP/E830VC1/E830VC2
3-4. AUDIO BLOCK DIAGRAM
RP-231 BOARD
MA-316 BOARD
(SEE PAGE 4-5)
J500
(SEE PAGE 4-11, 19)
L
FL504
IC360
SW 5V
IC340
12
CN260
VCC
HA
CN272
FE
REC ON
12
3
VCC
17
37
24
RFU750
3
R
FL505
TO
TUNER
BLOCK
(SEE PAGE 3-11)
15
FL502
A (L) OUT
16
FL503
1
CN500
A (L) IN
L2 L
PNR
R
PLL
20
L2 R
FL500
18
6
CA
2
FL501
9
+
36
15
NORM IN
13
4
14
AF REC P
13
LEVEL
DET
14
CN341
HF ADJ
39
FL573
INPUT SEL
41 42 44
3 4
8
7 6
5
2
2
X
A HEAD PB
IC201
NA REC
PB
PB
9
JS331
1
8
ALC
75
LINE
AMP
MUTE
77
ALC
DET
78
FROM
SYSCON
BLOCK
(SEE PAGE 3-5)
71
BIAS
ERASE
OSC
3
BIAS VCC
5
Q332
AUTO
BIAS
PS331
BIAS
ERASE
OSC
3
1
REC:
EP,LP
PB:EP
SW 12V
6
FULL ERS
79
REC
73
3
REC
T331,Q331
2
31
MUTE
CTL
11
PB:
LP,SP
1
T321,Q321
CN301
X
IC160
70
EQ
5
FULL
ERASE
HEAD
A MUTE
A VCC
CN305
10
1
CN570
DECODER/
LINE 3
6
FL571
L301
2
REC
4
2
1
A (R) IN
SW 5V
(2/2)
AUDIO
PROCESSOR
(MONO)
IC301
HEAD SW
4
A (R) OUT
9 10
6
6
7
4
SERIAL
DECODER
AUDIO
ERASE
HEAD
CN271
1
3
A (L) IN
1
76
CN302
AUDIO
REC/PB
HEAD
A (L) OUT
FL570
2
JS391
5
40 HID
12
REC
CLOCK
12
FL572
20
DATA
1
AF SW P
21
NORM OUT
JS390
1
15
HF
LPF
AGC
DET
CTL
PB ON
10
AFM REC
AGC
AMP
LPF
LINE 1
(TV)
A (R) IN
19
AV LINC
16
3
A (R) OUT
17
MUTE
FM
BPF
HA
13
L1 R
CN306
AFM PB
17
MOD A
14
MUTE
PNR
L
SW 12V
13
L1 L
SEL
35
12
MUTE
OUTPUT
PLL
18
CH2
RF
HF
LPF
17
11
CH1
AUDIO
PROCESSOR
(HIFI)
L341
AFM
REC/PB
AMP
DRUM
AUDIO
HEAD
SW 12V
(REAR)
AUDIO
LINE 2 OUT
L361
64
DATA (IIC)
IC160
28
63
CLOCK (IIC) IC160
30
A-H SW
2
80
Q301
BIAS
SW
(SEE PAGE 4-31)
FR-128
BOARD
J480
(FRONT)
AUDIO
LINE 2 IN
L
R
CN480
3
1
CN161
2L
Q800-804
3
2R
AV LINC
I/O BUFF
1
TUNER (L)
TU701 27 TU702 41
TUNER (R)
TU701 26 TU702 40
TUNER MONO
TU701 25 TU702 39
FROM
TUNER
BLOCK
IC160
59
AF SW P
IC160
100
IC160
96
AF REC P
IC160
2
FULL ERS
IC160
36
AF ENV
TO/FROM
SYSCON
BLOCK
(SEE PAGE 3-5)
16
3-7
TO/FROM
MODE CONT
BLOCK
FR-128 BOARD
CN181
(SEE PAGE 3-9)
(SEE PAGE 3-12)
REC
CN164
OUT
28
IN
32
3-8
SLV-E830B/E830NP/E830VC1/E830VC2
3-5. MODE CONTROL BLOCK DIAGRAM
FR-128 BOARD (SEE PAGE 4-31)
IC180
TIMER/TUNER
MODE CONTROL
ND420
VACUUM FLUORESCENT
INDICATOR TUBE
D186
L182
VDD 53
D6V
AVREF 0 77
AVREF 1 78
AVDD 79
F+
VDD 88
F15 32 . 35
P1
44 36
19
G1
VDD 89
FROM
POWER
BLOCK
9
IC420
D IN
CS
8
D OUT
CLK
FLD
DRIVER
VEE 34
6
5
9
IC183
RST 40
6
RESET
PULSE
GEN.
5
POWER FAIL 63
8
POWER
FAIL
DET.
7
-30V
IC400
11 FDP CS
18
9
10
14
15
22
23
5
26
6
FROM/TO
SYSCON
BLOCK
MA-316 BOARD
CN164
11
12
13
CN181
OSD CS
19 OSD CS
OSD S CLK
16
19
20
21
27
25
24
FROM/TO
AUDIO
BLOCK
MA-316 BOARD
CN164
4
8
REMOTE
CONTROL
RECEIVER
1
2
47 OSD SO
POWER CONT 2
24 POWER CONT 2
POWER CONT 1
IC180 $™ E-E
XTAL 42
X180
20MHz
23 POWER CONT 1
EXTAL 43
SCL
10 SCL
SDA
9
PDC DAV
H DET
SDA
67 PDC DAV
87 H DET
CG V
20MHz
S CLK
6.4Vp-p
TX 55
X181
32.768kHz
TEX 54
66 CG V
DM -73 BOARD
IC180 %¢ E-E
37 S CLK
S OUT
36 S OUT
S IN
35 S IN
(SEE PAGE 3-6)
17
SIRCS IN 6
48 OSD S CLK
OSD S IN
D187
ASURA RESET
21 ASURA RESET
22 ASURA CS
ASURA CS
PLL DATA
PLL CLK
TU ENABLE
32.768kHz
CN400
4.5Vp-p
LED CS 12
A/D 5 81
1
A/D 4 80
2
DMS 2 85
5
DMS 1 84
3
18 PLL DATA
S407
17 PLL CLK
EJECT
Q450
CN452
7
LED CS
A/D 5
A/D 4
DMS 2
DMS 1
(SEE PAGE 4-37)
D459
LED
DRIVE
5
JOG
11
10
7
9
S453
S457
S458
REW
FF
PAUSE
16 TU ENABLE
AFT
86 AFT
LANC IN
LANC OUT
AV LINC IN
3
LANC IN
4
LANC OUT
69 AV LINC IN
AV LINC OUT
A/D 2 74
S401
PROGRAM /
TRACKING +
A/D 1 73
57 AV LINC OUT
S402
S408
S406
AUTO
SET UP
AUDIO
DUB
QUICK
TIMER
S451
S459
REC
JOG
DMS BLOCK
QUICK SHUTTLE
CN451
1
S404
2
PROGRAM /
TRACKING
3
4
5
(SEE PAGE 3-8)
A/D 0 72
IC182
SCL 6
MODE 7
S411
OFF
POWER
SAVE
S400
EEPROM
SDA 5
ON
STANDBY
7 EEP SDA
8 EEP SCL
99 EEP MODE
Q400
BZ181
LED
DRIVE
62 BUZZER
D5V
D400
POWER ON
16
3-9
3-10
PLAY
STOP
PLAY
COM
DMS 2
DMS 1
STOP
SLV-E830B/E830NP/E830VC1/E830VC2
3-6. TUNER BLOCK DIAGRAM
EXCEPT NP MODEL
RFU 750
(SEE PAGE 4-21)
IN
TU702
UHF/
VHF
IC540
IC820
4
3
L OUT 41
R OUT 40
TU L
TU R
IC360
IC360
1
2
4
SDA
SCL
RF AGC
DATA
CLOCK
ENABLE
BG/L
BG L/L
AFT
(SEE PAGE 3-8)
M OUT 39
5 9 7 6
11 12 25
34 33 21 14 13 15 35 36 24
2 3 11
20 19 7 5 4 6 21 22 10
SDA
SCL
RF AGC
DATA
CLOCK
ENABLE
BG/L
BG/L/L
3
30V
5V
5V
MOD A
30V
5V
5V
RF
MOD
IC360 12
TU VIDEO
TU M
Q751,752
L755
D750
MODE
CONT
L750
D6V
R711
UN30V
L701
SW 5V
IC160 25
CN164 13
CN164 14
MODE CONT
SDA
SCL
Q703
IC160 5
AUTO PRESET
CN164 17
CN164 16
CN164 15
PLL DATA
PLL CLOCK
TU ENABLE
IC160 18
IC160 51
CN164 9
SW 1
SW 2
AFT
(SEE PAGE 3-6)
NP MODEL
UHF/
VHF
IN
OUT
TU701
TU/IF
DEMODULATOR
AFT
TO/FROM
SYSCON
BLOCK
AUTO
PRESET
V DET 18
L OUT 27
R OUT 26
M OUT 25
16
3-11
3-12
TO
VIDEO
BLOCK
(SEE PAGE 3-3)
TO
AUDIO
BLOCK
VTR
2
TV/VTR
FROM
AUDIO
BLOCK
Q510 MOD V
V DET 32
TV
OUT
(SEE PAGE 3-3)
FROM
VIDEO
BLOCK
TU/IF
DEMODULATOR
RF
SPLITTER
UNSW 5V
30V
SDA
SCL
MA-316 BOARD
IC360
44
(SEE PAGE 3-8)
SLV-E830B/E830NP/E830VC1/E830VC2
3-7. POWER SUPPLY BLOCK DIAGRAM
5V
2
3 11
11 12 25
5V
30V
5 4
5V
9
TU701
5V
UNSW 5V
(SEE PAGE 4-41)
30V
POWER BLOCK
(NP MODEL)
TU702
30V
(EXCEPT NP MODEL)
RFU750
TV/VTR
MA-316
BOARD
(SEE PAGE 4-11, 14, 17,
19, 21, 23, 25)
T101
CN101
F101
AC
IN
L101
L102
CN201
4
D251
3
D252
L201
D253
L202
D101-104
IC151,Q151
2
SWITCHING
5
D254
15
.
16
IC201
1
L205
CN600
38V
4
R711
4
UNSW 13V
15
.
16
IC660
L750
Q751,752
12V
REG
2
SW 12V
12
IC201
L705
D750
12
OSD
L701
6
POWER CONT 2
13
D255
6.
7
MOTOR
12V SW
PC151
MTR 12V
POWER CONT 1
11
7 VCC
L204
L206
13
IC661
36 Y VCC
47 C VCC
AFC
L663
13 VCC
Q201,204
L204
(1/2)
Y/C PROC.
SW
4
L203
7
L662
IC202
6.
7
IC820
1H DELAY
L205
FOLLOW TV
2 VDD
11
PS202
2.
3
SW 5V
REG
D 6V
14
IC180
2.
3
SW 5V
PS201
CN164
D 6V
14
CN181
TIMER/TUNER
MODE CONT.
L182
31
5
D187
Q207
IC360
-30V
SW
-30V
18
Q208
+F (5.4V)
16
SWITCH
17
POWER SAVE CONT
-F (0V)
19
12V
1
REG
IC201
AUDIO PROC.
(HIFI)
IC530
18
L530
PS251
FR-128 BOARD (SEE PAGE 4-31)
8 VCC
Q205,206
PHOTO
COUPLER
76 AVCC
Q533,534
PS533
17
C+ BUFFER
POWER SW
21
15
22
14
C+ BUFFER
A/V CONT
IC182
EEPROM
C+ VIDEO
I/O SEL
8 VCC
Q611,612
PVCC 1 20
D610
PVCC 2 19
PS131
C+
VCC
POWER
ON
(SEE PAGE 4-33)
CN970
VCC 22
8
SERVO/SYSTEM
CONTROL
CN307
SW 5V
8
34 VEE
ND420
IC160
L975
45 VDD
IC183
RESET
5 VCC2 PULSE
GEN.
SE-69 BOARD
SECAM DET
14 VDD
33 VDD
D400
PVCC 3 18
IC970
DISPLAY
DRIVER
23 POWER CONT 1
24 POWER CONT 2
IC540
19
2 VCC
IC420
POWER CONT 1
POWER CONT 2
16
REMOTE
CONTROL
RECEIVER
89 VDD
L301
35 12V
77 AVREF 0
78 AVREF 1
79 AVDD
88 VDD
AUDIO PROC.
(MONO)
L361
2
(2/2)
IC400
D186
7 VCC1
L161
D160
POWER
FAIL
DET.
VACUUM
FLUORESCENT
INDICATOR TUBE
F+
AVREF 53
24 POWER SAVE C+
AVDD 54
23 POWER SAVE CONT
VDD 89
B MODEL ONLY
D420
-30V
+F (5.4V)
5V 90
-F (0V)
(SEE PAGE 4-5)
IC140
Q100,101
VCC 29
T/S
SENSOR
L263
VDDA 20
D 6V
L341
VCC 14
BIAS
ERASE
OSC
CN272
10
L321
9
SW 5V
SW 5V
LOADING
MOTOR
DRIVE
CN306
10
CHECK
PIN
9
CN101
IC141
D131
8 VCC
9 VCC
CTL AMP
L141
MTR 12V
1
CN102
MTR 12V
SW 5V
PS331
2
SW 12V
2
7
1
PS130
16
3-13
DRUM
MOTOR
D132
8 VCC
T331,Q331,332
BIAS
ERASE
OSC
4
IC161
AUDIO
REC/PB AMP
T321,Q321
1
CN165
D108
IC340
HEAD
SW
2
35
8 VCC
VDDD 19
L262
VCC 16
IC301
34
DRUM
CAPSTAN
AMP
VPS/PDC
DECODER
T/S
REEL
VIDEO
REC/PB AMP
VCC 8
IC850
PH100,101
IC260
L140
3
IC100
RP- 231 BOARD
CAPSTAN
SPEED
CONTROL
33
3-14E
CAPSTAN
MOTOR
F-
SLV-E830B/E830NP/E830VC1/E830VC2
SECTION 4
PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
4-1. FRAME SCHEMATIC DIAGRAM
4-1
4-2
FRAME SCHEMATIC DIAGRAM
SLV-E830B/E830NP/E830VC1/E830VC2
RP-231 (REC/PB AMP) SCHEMATIC DIAGRAM
— Ref. No.: RP-231 Board; 1,000 Series —
THIS NOTE IS COMMON FOR PRINTED WIRING
BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is
printed in each block.)
• For printed wiring boards.
•
: Pattern from the side which enables seeing.
Caution :
Pattern face side:
(Conductor Side)
Parts on the pattern face side
seen from the pattern face are
indicated.
Pattern face side: parts on the parts face side seen
(Component Side) from the parts face are indicated.
• For schematic diagrams.
• Caution when replacing chip parts.
New parts must be attached after removal of chip.
Be careful not to heat the minus side of tantalum
capacitor, because it is damaged by the heat.
• All resistor are in ohms, 1/4W unless otherwise noted.
Chip resistor are 1/10W unless otherwise noted.
kΩ: 1000Ω, MΩ, : 1000kΩ.
• All capacitors are in µF unless otherwise noted. pF : µ
µF. 50V or less are not indicated except for electrolytics
and tantalums.
•
: panel designation.
•
: internal component.
•
: B+ Line. *
: B– Line. *
•
•
: IN/OUT direction of (+,–) B LINE. *
• Circled numbers refer to waveforms. *
• Readings are taken with a PAL color-bar signal input.
• Voltage are dc between ground and measurement
points.*
• Readings are taken with a digital multimeter (DC10MΩ).*
• Voltage variations may be noted due to normal production
tolerances.*
When indicating parts by reference number, please
include the board name.
• * : indicated by the color red.
4-5
4-6
4-7
REC/PB AMP
RP-231
SLV-E830B/E830NP/E830VC1/E830VC2
MA-316 (VIDEO, NORMAL AUDIO) SCHEMATIC DIAGRAM
— Ref. No.: MA-316 Board; 2,000 Series —
MA-316 BOARD (1/3)
5 IC201 #∞ REC
1 IC201 !∞ REC
75mVp-p
H
1 IC201 !∞ PB
1Vp-p
H
6 IC201 #¶ REC/PB
4.2Vp-p
H
0.1µsec/div
0.2V/div
2 IC201 @∞ REC
7 IC201 #• REC
440mVp-p
H
3 IC201 $• REC
H
8 IC201 !¢ REC
4-11
4-12
4-13
0.6Vp-p
0.42Vp-p
H
0.34Vp-p
4 IC201 ^º REC/PB
4.43MHz
2.4Vp-p
H
9 IC201 $∞ PB
H
470mVp-p
VIDEO, NORMAL AUDIO
MA-316 (1/8)
SLV-E830B/E830NP/E830VC1/E830VC2
MA-316 (SERVO/SYSTEM CONTROL) SCHEMATIC DIAGRAM
— Ref. No.: MA-316 Board; 2,000 Series —
• See page 4-9 for MA-316 BOARD printed wiring board.
MA-316 BOARD (2/3)
!™ CN101 3 REC/PB
25Hz
5Vp-p
!£ CN101 4 REC/PB
300Hz
5Vp-p
!¢ CN102 3, IC160 &º
REC/PB
5Vp-p
758Hz
!∞ IC160 7 REC/PB
25Hz
4Vp-p
(SEE PAGE 4-42)
!§ IC160 $™ REC/PB
16MHz
4Vp-p
!¶ IC160 1, 100 REC/PB
25Hz
5Vp-p
!• IC160 ^¶ REC/PB
25Hz
5Vp-p
SERVO/SYSTEM CONTROL
MA-316 (2/8)
4-14
4-15
4-16
SLV-E830B/E830NP/E830VC1/E830VC2
MA-316 (ON SCREEN DISPLAY) SCHEMATIC DIAGRAM
— Ref. No.: MA-316 Board; 2,000 Series —
• See page 4-9 for MA-316 BOARD printed wiring board.
MA-316 BOARD (3/3)
!º IC660 8 REC/PB
17.73MHz
5.5Vp-p
!¡ IC660 @∞ REC/PB
H
4-17
4-18
2.4Vp-p
ON SCREEN DISPLAY
MA-316 (3/8)
SLV-E830B/E830NP/E830VC1/E830VC2
MA-316 (AFM AUDIO) SCHEMATIC DIAGRAM
— Ref. No.: MA-316 Board; 2,000 Series —
AFM AUDIO
MA-316 (4/8)
• See page 4-9 for MA-316 BOARD printed wiring board.
4-19
4-20
SLV-E830B/E830NP/E830VC1/E830VC2
MA-316 (TUNER) SCHEMATIC DIAGRAM
— Ref. No.: MA-316 Board; 2,000 Series —
• See page 4-9 for MA-316 BOARD printed wiring board.
4-21
4-22
TUNER
MA-316 (5/8)
SLV-E830B/E830NP/E830VC1/E830VC2
MA-316 (FOLLOW TV, PDC, VPS) SCHEMATIC DIAGRAM
— Ref. No.: MA-316 Board; 2,000 Series —
FOLLOW TV, PDC, VPS
MA-316 (6/8), (7/8)
• See page 4-9 for MA-316 BOARD printed wiring board.
4-23
4-24
SLV-E830B/E830NP/E830VC1/E830VC2
MA-316 (I/O) SCHEMATIC DIAGRAM
— Ref. No.: MA-316 Board; 2,000 Series —
• See page 4-9 for MA-316 BOARD printed wiring board.
4-25
4-26
4-27
I/O
MA-316 (8/8)
SLV-E830B/E830NP/E830VC1/E830VC2
FR-128 (MODE CONTROL) SCHEMATIC DIAGRAM
— Ref. No.: FR-128 Board; 3,000 Series —
4-31
4-32
MODE CONTROL
FR-128
SLV-E830B/E830NP/E830VC1/E830VC2
SE-69 (SECAM VIDEO SIGNAL PROCESS) SCHEMATIC DIAGRAM
— Ref. No.: SE-69 Board; 2,000 Series —
SECAM VIDEO SIGNAL PROCESS
SE-69
4-33
4-34
SLV-E830B/E830NP/E830VC1/E830VC2
DM-73 (OPERATION SWITCHES) SCHEMATIC DIAGRAM
— Ref. No.: DM-73 Board; 2,000 Series —
4-37
OPERATION SWITCHES
DM-73
SLV-E830B/E830NP/E830VC1/E830VC2
SLV-E830B/E830NP/E830VC1/E830VC2
POWER BLOCK SR826 (SWITCHING REGULATOR) PRINTED WIRING BOARD
— Ref. No. SR826 Board; 9,000 Series —
POWER BLOCK SR826
MAIN BOARD (CONDUCTOR SIDE)
SUB BOARD (CONDUCTOR SIDE)
IC251
D151
D251
R251 C157
C152
L151
Q151
R154
C256
C251
D252
R156
D156
C151
D158
R152
D155
D153
R153
D154
D152
R157
C252
IC151
R151
C154
D254
D253
R158
R252
D526
D255
C253
C254
R253
C255
PS251
R254
C153
VR251
MA-316
VIDEO, AUDIO,
SERVO/SYSTEM CONTROL,
TUNER
RP-231 (REC/PB AMP)
SE-69 (SLV-E830B)
SECAM VIDEO SIGNAL
PROCESS
FR-128
(MODE CONTROL)
POWER BLOCK
DM-73
(OPERATION SWITCHES)
SWITCHING REGULATOR
SR826
4-39
4-40
SLV-E830B/E830NP/E830VC1/E830VC2
POWER BLOCK SR826 (SWITCHING REGULATOR) SCHEMATIC DIAGRAM
— Ref. No. SR826 Board; 9,000 Series —
C
SUB BOARD
T151
POWER
TRANSFORMER
1, 2
3
!
C104 C103
1000p 1000p
/250
/250
L102
4
!
!
!
S
!
!
C108
1000p
/250V
D156
1N4005
!
C109
1000p
/250V
C161
1500p
IC151
AN8028
D151 AK04
1
R162 2.2K
R163 10K
C162 3300p
C105
1000p
/250V
C163 3300p
*R164
C101
0.1/250
*R165
L101
D158
MA4270
3
4
+
!
6
C164
0.033
S2A
D253
D3S4M
+
!
C253
2200
/ 10
B1
S5
*R167
B2
!
S6
GND
!
*R261
+
C261
0.22 R263
18K
*R252
*R265
C254
47 / 50
R264
15K
+
R207
220
D203
RD5.1ES
D204
1SS119
D205
1SS119
+
The components indentified by mark ! or dotted
7
16
line with mark ! are critical for safety.
Replace onl y with part number specified.
4-41
Ref.No.
*R156
*R164
*R165
*R167
Q205
2SD2394
!
R222
220 R208
220
+
+
L206
GND
C212
0.01
L205 1uH
13
!
C204
100 / 16
+
R206
1.5K
C206
47 / 35
C207
22 / 50
C209
47 / 50
9, 10
CN201
1 GND
2 SW 5V
3 SW 5V
4 38V
5 13V
6 13V
7 MTR 12V
8 MTR 12V
9 GND
10 GND
11 POWER CONT 1
12 SW 12V
13 POWER CONT 2
14 D 6 V
15 GND
16 + F (6.0 V)
17 POWER SAVE CONT
18 - 30 V
19 - F (0 V)
E
TO/FROM
MA-316
BOARD
CN600
(SEE PAGE
4-16)
Q207
2SD774
L203 1uH
PS251
15
C255
470 / 10
C256
0.1
14
*R254
D255
AU02Z
min
typ
max
Ref.No.
0.27
270
330
1.5K
0.33
330
470
1.8K
0.39
330
560
2.2K
*R252
*R254
*R265
R213
47K
L204 1uH
R216
10K
C210
0.047
Note:
R220
4.7K
PS201 1.6A
PS202 2A
+
A
+
!
L202
20uH
R205
2.2K
Q204
2SC1740
R219
4.7K
C205
22 / 50
11, 12
K
SHUNT REG.
AN1431T
R253
0.47
S7
VR251
5K
PC151
PS2561
IC251
D254
AU02Z
PC151
PS2561
L
AC IN
CN101
220-240VAC
50/60Hz
D256
MA2560
S2B
8
R166
1K
REG.
C201
220 PQ12RD08
16
S1
9
!
+
9, 10
7
C154
1
F101
250V T2A
N
+
+
C153
47
R203
180 / 2
IC201
C252
1000
/ 16
D154 AK04
Z101 750V
R101
2.7M 1/2
+
C203
220 / 16
7, 8
S3
5
D155
AU02Z
R201
1K
L201
10uH
D252
S3L20U
2
6
5
P2
Q151
FS2KM
+
Q201
2SB733
C208 470 / 10
C102
0.1/250
!
D152
EG01C
C165
3300p
D153
1SS119
4, 5
R168
10K
R210 1K
*R156
/1W
D102
+
C251
47 / 50
L151
R169 18K
D104
C151
47 / 400
D251 R251
AU02Z 10
S4
6
R161 22K
+
R151
150K
R152
150K
R153
150K
R157 82
D101
D103
L103
R154
C152
100K 2 0.01 / 400 P1
R158 22
2
L
!
MAIN BOARD
D101-104
1N4005
K
J
I
H
R209
220
1
G
F
Q206
2SC2785
POWER BLOCK
(SR826)
E
D
C202 470 / 10
B
*R266
A
min
4.7
2.2
1K
typ
max
10
2.7
10K
10
3.3
22K
Q208
2SD774
R215
8.2K
C211
0.047
Q210
UN4111
R214
47K
Q209
UN4111
Q211
UN4211
4-42E
SWITCHING REGULATOR
SR826
O
I
O
4
^§
!£
QVD
V SYNC
NT JUDGE
STOP
L
*4
L
*1
FF/REW
TAPE
TAPE
L
*5
L
*1
L
*5
*2
*1
PB
L
*5
*3
*1
PB PAUSE
L
*5
*3
*1
SLOW
L
*5
*2
*1
x2
L
*5
*3
*1
CUE
L
*5
*3
*1
REVIEW
L
*5
L
*1
REC
I/O
O
O (O.D)
O
I
I
I
I
Pin No.
7
#∞
(ª
^¶
^•
^ª
&º
REC CTL
CAP STOP
STEP PLS
PB CTL
DRM PG
DRM FG
CAP FG
5-1
O
I/O
&¢
8
DRM DA
CTL RESET
Hi-Z
*10
*8
H/L
*4
*4
H
L
L
Hi-Z
STOP
*1. 25Hz pulse.
*2. Pulse at tape running.
*3. Reverse logic pulse of STEP PLS.
*4. “L” when drum rotation stops.
*5. Unstable period pulse.
*6. Pulse in period in proportional to tape speed.
*7. 300Hz pulse.
*8. Pulse at tape running.
*9. Approx. 2 msec period “H” or “L” pulse.
*10. Approx. 1.5 msec period “H” or “L” pulse.
*11. “L” when FWD SLOW, “H” when RVS SLOW.
O
&£
CAP DA
Signal
Hi-Z
*10
*8
*6
*7
*1
*6
L
Hi-Z (O.D)
Hi-Z
FF
Hi-Z
*10
*8
*6
*7
*1
*6
L
Hi-Z (O.D)
Hi-Z
REW
TAPE
TAPE
Hi-Z
*10
*8
*5
*5
*5
L
Hi-Z (O.D)
Hi-Z
Hi-Z
*10
*8
*5
*5
*5
L
Hi-Z (O.D)
Hi-Z
THREADING UNTHREADING
PB
Hi-Z
*10
*9
*6
*7
*1
*1
L
Hi-Z (O.D)
Hi-Z
Hi-Z
*10
*8
H/L
*7
*1
H/L
L
L
Hi-Z
PB PAUSE
*11
*10
*8
*2
*7
*1
*2
*2
*3
Hi-Z
SLOW
Hi-Z
*10
*9
*6
*7
*1
*6
L
Hi-Z (O.D)
Hi-Z
CUE
x2
Hi-Z
*10
*8
*6
*7
*1
*6
L
Hi-Z (O.D)
Hi-Z
Hi-Z
*10
*9
*6
*7
*1
*6
L
Hi-Z (O.D)
Hi-Z
REVIEW
L
*5
L
*1
REC PAUSE
5-2. SYSTEM CONTROL — SERVO PERIPHERAL CIRCUIT INTERFACE (MA-316 BOARD IC160)
L
*5
L
*1
THREADING UNTHREADING
Synchronized with drum rotation. 25Hz 50% duty cycle.
Normally “L“. “H“ when CTL signal is not generated.
V period “H“ pulse.
Selected by REC mode. “H“ in LP mode.“
Composite sync signal (positive).
O
1
RF SWP
*1
*2
*3
*4
*5
I/O
Pin No.
Signal
5-1. SYSTEM CONTROL — VIDEO BLOCK INTERFACE (MA-316 BOARD IC160)
Hi-Z
*10
*9
*6
*7
*1
*1
L
Hi-Z (O.D)
*1
REC
Hi-Z
*10
*8
H/L
*7
*1
H
L
Hi-Z (O.D)
Hi-Z
REC PAUSE
SLV-E830B/E830NP/E830VC1/E830VC2
SECTION 5
INTERFACE, IC PIN FUNCTION DESCRIPTION
5-2
I
I
I
I
I
I
I
O (O.D)
O (O.D)
O
I
I
@™
@¡
@º
!ª
!∞
^¢
^£
#™
#∞
&™
^¡
^™
MODE 1 (*8)
MODE 2 (*8)
MODE 3 (*8)
MODE 4 (*8)
(IN REC PRF)
T REEL FG
S REEL FG
T/E LED
CAP STOP
CAP RVS
T SENS
S SENS
*4
*4
H
L
*4
H/L
H/L
H
L
L
H
H
L
EJECTED
*4
*4
L
*4
H/L
H/L
*2
H
L
L
L
H
LOADING
TAPE
TAPE
*4
*4
L
*4
H/L
H/L
*2
H
L
L
L
L
L
*6
*6
H
H
*4
*3
H/L
*2
*1
*1
*1
*1
*6
*6
H/L
L
*4
H/L
H/L
*2
L
H
H
H
*7
STOP
*6
*6
L
H
*4
*3
*3
*2
H
L
H
H
*7
FF
*6
*6
H
H
*4
*3
*3
*2
H
L
H
H
*7
REW
*6
*6
L
H
*4
*3
*3
*2
H
L
L
H
*7
PB
*6
*6
L
L
*4
H/L
H/L
*2
L
L
L
H
*7
PB PAUSE
*6
*6
L/*5
*5
*4
*3
*3
*2
L
L
L
H
*7
SLOW
*6
*6
L
H
*4
*3
*3
*2
L
L
L
H
*7
x2
*6
*6
L
H
*4
*3
*3
*2
L
L
L
H
*7
CUE
*6
*6
H
H
*4
*3
*3
*2
L
H
L
L
*7
REVIEW
I
I
I
O
I
$º
$¢
$∞
$§
$¶
ASURA CS
S IN 0
S OUT 0
S CLK
I/O Level
Serial communication clock from timer microprocessor. V period “L” pulse.
Serial communication data to timer microprocessor. V period “L” pulse.
Serial communication data from timer microprocessor. V period “ L” pulse.
Chip select signal from timer microprocessor. V period “L” pulse.
Normally “H”, “L” when service interruption is detected or restored.
I
O (O.D)
O
O
O (O.D)
%ª
#¡
2
`⁄‚‚
#§
AF ENV
A MUTEN
AF REC P
AF SWP
FULL ERS
TAPE
LOADING
TAPE
UNLOADING
PB
H
*1
L
L
H
*1
L
L
H
*1
L
L
H
*1
L
*1
H
*1
L
H
PB PAUSE
AF RF envelope signal input terminal for automatic tracking.
REW
STOP/FF/
*1. 25 Hz 50 % duty pulse approx. 5 msec delayed from RF SW P.
I/O
Pin No.
Signal
H
*1
L
H
SLOW
H
*1
L
H
x2
H
*1
L
H
CUE
5-5. SYSTEM CONTROL — AUDIO BLOCK INTERFACE (MA-316 BOARD IC160)
I/O
Pin No.
Signal
ASURA RESET
H
*1
L
H
REVIEW
L
*1
H
L
REC
H
*1
L
L
REC PAUSE
5-4. SYSTEM CONTROL — SYSTEM CONTROL PERIPHERAL CIRCUIT INTERFACE (MA-316 BOARD IC160)
*7. When transition to UNLOADING direction : “L”.
When transition to LOADING direction : “H”.
When CAM MOTOR is stopped : Hi-Z.
*8. When RVS slow : Mode 1=”L”
When RVS slow : Mode 2=”L”
When RVS slow : Mode 3=”H”
When RVS slow : Mode 4=”L”
*6
*6
L
H
*4
*3
H/L
*2
*1
*1
*1
*1
H
UNLOADING THREADING UNTHREADING
CASSETTE CASSETTE
Uncertainly.
“L” when erasing protection tab is bent. “H” when not bent.
Pause of period in proportion to reel rotating speed.
Approx. 2 msec period “H” pulse.
Pulse at tape running.
Normally “L”. 2 msec period “H” pulse when tape top or tape end is detected.
HI-Z
9
CAM2
*1.
*2.
*3.
*4.
*5.
*6.
I/O
Pin No.
Signal
5-3. SYSTEM CONTROL — MECHANISM INTERFACE (MA-316 BOARD IC160)
*6
*6
L
H
*4
*3
*3
*2
L
L
L
H
*7
REC
REC
*6
*6
L
L
*4
H/L
H/L
*2
L
L
L
H
*7
PAUSE
5-6. SERVO/SYSTEM CONTROL MICROPROCESSOR PIN FUNCTIONS
(MA-316 BOARD IC160)
Pin No.
1
2
3
4
5
6
7
Pin Name
RF SWP
AF REC P
N.C.
QVD
AUTO PRESET
FE ON
REC CTL
I/O
O
O
—
O
O
O
O
Function
RF switching pulse output.
“H” when HiFi audio REC.
Not used.
Quasi VD pulse output.
“H” during auto preset.
Flying erase ON/OFF
REC CTL signal output.
Capstan current control. “H” during
slow mode.
Cam motor control.
Not used.
Tuner audio mute. H: Mute
“H” when the SECAM signal is
detected.
4.43/3.58 judge input.
“H” when the MESECAM signal is
detected.
Erasing protection tab, cassette in
8
CTL RESET
O
9
10
11
CAM 2
N.C.
TA MUTE
I
—
O
12
SECAM DET
I
13
NT JUDGE
I
14
MESECAM DET
I
15
CIN (REC PRE)
I
16
17
18
19
20
21
22
AV CONT
C+ DET
SW1
MODE 4
MODE 3
MODE 2
MODE 1
POWER SAVE
CONT 1
POWER SAVE
C+
O
I
O
I
I
I
I
detection signal input.
TV/VTR.
CANAL + detection.
BG/L control signal.
Cam encoder signal input.
Cam encoder signal input.
Cam encoder signal input.
Cam encoder signal input.
O
–30V Power supply control.
O
C+ IC Power supply control.
23
24
25
MOD CONT
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
SECAM ON
N.C.
SDA 0
N.C.
SCL 0
A MUTE
T/E LED
N.C.
N.C.
CAP STOP
FULL ERS
N.C.
N.C.
MP
ASURA RESET
VSS
XTAL
EXTAL
44
ASURA CS
45
46
47
48
49
50
S IN 0
S OUT 0
SCLK
N.C.
N.C.
N.C.
Tuner modulation output control
signal.
O SECAM control signal output.
— Not used.
I/O I2C data.
— Not used.
I/O I2C clock.
O “H” when audio mute.
O Tape top/end sensors driver.
— Not used.
— Not used.
O Capstan stop signal output.
O Full erase control.
— Not used.
— Not used.
I Fixed to “L”.
I System reset signal.
— Ground.
O System clock 16MHz.
I System clock 16MHz.
Servo/system control microcomputer
I
chip select signal.
I Serial communication signal.
O Serial communication signal.
I Serial communication signal.
— Not used.
— Not used.
— Not used.
O
5-3
Pin No.
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
Pin Name
SW2
AVSS
AVREF
AVDD
NTPB SW
AV ADJ
FOLLOW TV
GND
AF ENV
RF ENV
T SENS
S SENS
S REEL FG
T REEL FG
N.C.
CSYNC
PB CTL
I/O
O
—
—
—
I
I
I
—
I
I
I
I
I
I
—
I
I
Function
BG/L’ control signal.
Unswitched ground.
AD port reference input UNSW 5V.
UNSW 5V.
NTSC playback switch.
Adjustment mode.
Synchro-TP detection signal.
Ground.
HiFi audio playback signal envelope.
Video playback signal envelope.
Take-up end sensor.
Supply end sensor.
Supply reel FG input.
Take-up reel FG input.
Not used.
Composite sync. signal input.
Playback CTL input.
68
69
70
71
DRM PG
DRM FG
CAP FG
SECAM MIX
I
I
I
O
72
CAP RVS
O
73
74
75
76
77
78
79
80
81
82
83
CAP DA
DRM DA
CTL REC
CTL STEP
REC COUNT
GND
DNR RESET
DATA (SSB)
CLOCK (SSB)
N.C.
N.C.
O
O
—
—
I
—
O
O
O
—
—
84
CAP TRQ PWM
O
85
86
87
88
89
90
91
92
93
94
95
96
97
98
N.C.
N.C.
N.C.
VSS
VDD
5V
N.C.
CTL HYS HIGH
N.C.
N.C.
N.C.
REC
N.C.
N.C.
—
—
—
—
—
—
—
O
—
—
—
O
—
—
99
STEP PLS
O
100
AF SWP
O
Drum PG input.
Drum FG input.
Capstan FG input.
SECAM MIX control.
Capstan reverse control “H” when
reverse.
Capstan error D/A output.
Drum PG output.
Not used.
Not used.
Counter signal input when recording.
Ground.
DNR reset signal.
Serial communication data.
Serial communication clock.
Not used.
Not used.
PWM output for capstan torque
control.
Not used.
Not used.
Not used.
Ground.
5V.
5V.
Not used.
CTL amp gain control.
Not used.
Not used.
Not used.
“H” output when hifi audio recording.
Not used.
Not used.
Step pulse “H” when capstan step
driving.
AF switching pulse output.
5-7. TUNER/TIMER MODE CONTROL PIN FUNCTIONS
(FR-128 BOARD IC180)
Pin No.
Pin Name
I/O
1
TXT RST
O
2
—
5
6
7
8
9
10
11
12
13
14
15
16
17
18
N.C.
LANC IN
(SENSOR)
LANC OUT
(SENSOR)
N.C.
SIRCS IN
EEP DATA
EEP SCL
SDA
SCL
FDP CS
LED CS
X-UCOM CS
N.C.
VSS
TU ENABLE
PLL CLK
PLL DATA
19
OSD CS
O
20
N.C.
—
21
ASURA RESET
O
22
ASURA CS
O
23
POWER CONT
O
24
POWER CONT
O
25
26
27
28
29
30
31
32
N.C
OPTION 1
OPTION 2
N.C.
OPTION 3
N.C.
N.C.
Not used
—
O
I
—
—
—
—
—
33
34
35
36
37
38
39
40
41
Not used
— Positive supply voltage
Not used
— Positive supply voltage
SI (TO CME)
I Serial data input
SO (FROM CME) O Serial data output
SCLK
I/O SCLK
N.C.
—
N.C.
—
RST
I System reset
VSS
— Ground
Internal oscillator output for 20MHz
XTAL
O
crystal
Internal oscillator 20MHz crystal
EXTAL
I
input
VDD
— Positive supply voltage
N.C.
—
N.C.
—
OSD SO
O Serial data output
(FROM CME)
3
4
42
43
44
45
46
47
I
Lanc input
O
Lanc output
—
I
I/O
I/O
I/O
I/O
O
O
O
—
—
O
O
O
Pin No.
48
49
50
51
52
53
Function
Teletext IC (ML Board IC950) reset
signal
Remote control input
I2C bus interface data input/output
I2C bus interface clock input/output
I2C bus interface data input/output
I2C bus interface clock input/output
FLD driver chip select
LED driver chip select
ML IC chip select(ML board IC902)
Ground
Tuner chip select
Tuner PLL clock
Tuner PLL data
OSD IC (MA-316 board IC660)
chip select
S/S micon (MA-316 board IC160)
reset signal
S/S micon (MA-316 board IC160)
chip select signal
Main power supply control signal
Secondary power supply control
signal
ML board IC950 enable signal
ML board IC950 busy signal
ML
Positive supply voltage
5-4E
Pin Name
OSD CLK
N.C.
N.C.
N.C.
N.C.
VDD
54
TEX
55
TX
56
57
58
59
60
61
VSS
AV LINK OUT
SIRCS OUT
N.C.
N.C.
N.C.
62
BUZZER
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
POWER FAIL
Not used
Not used
CGV
PDC DAV
Not used
AV LINK IN
Not used
Not used
A/D0
A/D1
A/D2
A/D3
A VSS
A VREF0
A VREF1
A VDD
A/D4
A/D5
A/D6
Not used
DMS1
DMS2
AFT
HDET
VDD
VDD
VSS
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
EEP MODE
100
0X-UCOM RST
I/O
Function
O Serial clock input/output
—
—
—
—
— Positive supply voltage
Internal oscillator 32kHz crystal
I
input
Internal oscillator output for 32kHz
O
crystal
— Ground
O AV LINK output
O Remote control output
—
—
—
Buzzer output/clock crystal
O
frequency division output
I Power voltage drop detection pin
— Positive supply voltage
— Positive supply voltage
I Vertical synchro detection
I VPS/PDC acknowledge signal
— Positive supply voltage
I AV LINK input
— Positive supply voltage
— Positive supply voltage
I Key pad reading
I Key pad reading
I Key pad reading
I Key pad reading
— Ground
— Positive supply voltage
— Positive supply voltage
— Positive supply voltage
I Key pad reading
I Key pad reading
—
—
I
I
I Ground wave tuner AFT detection
I HDET signal input
— Positive supply voltage
— Positive supply voltage
— Ground
—
—
—
—
—
—
—
—
O EEP mode control
X-UCOM reset signal
O
(IC902 ML board)
SLV-E830B/E830NP/E830VC1/E830VC2
SECTION 6
ADJUSTMENTS
2-1-3. Input Signal Check
Video signal produced by a pattern generator is used as an adjustment
signal to perform electrical alignment for this unit. This video signal
must satisfy the specification.
6-1. MECHANICAL ADJUSTMENTS
For the mechanical adjustments, please refer to the
“VHS MECHANICAL ADJUSTMENT MANUAL
(S MECHANISM)” (9-921-647-11).
Unless otherwise specified, place the switches and controls of this
unit in the following positions:
• INPUT SELECT switch ................................................. LINE 1
6-2. ELECTRICAL ADJUSTMENTS
Connect an oscilloscope to the Video Input terminal. Check that the
synchronizing signal of the Y signal has an amplitude of
approximately 0.7V and that the burst signal has an amplitude of
approximately 0.3V and its waveform is flat. And check that the
level ratio of burst signal to “red” signal is 0.30 : 0.66. The video
signal (color bar) used for electrical aligning this unit is shown in
Fig. 6-2-2.
See the adjustment parts location diagram on page 6-6
for the adjustment.
2-1.
PREPARATION BEFORE ADJUSTMENT
2-1-1. Equipment Required
The measuring instruments used for this alignment include:
1) Monitor TV
2) Oscilloscope, dual-trace, bandwidth of 30MHz or more, with
delay mode (A probe 10:1 should be used unless otherwise
specified.)
3) Frequency counter
4) Pattern generator
5) Digital voltmeter
6) Audio generator
7) Audio level meter
8) Audio distortion meter
9) Audio attenuator
10) Alignment tapes
KRV-51P
Part No. : 8-192-605-36
White (Approx. 75%)
Approx. 0.7 V
Approx. 0.3 V
Red
Horizontal sync signal
2-1-2. Equipment Connection
Unless otherwise specified, connect and adjust the measuring
instruments as shown in the following diagram.
2-1-4. Alignment Tape
• Contents of KRV-51P
Mode
VCR
Period
Video signal
7 minutes
3 minutes
7 minutes
3 minutes
Color bar
Monoscope
Color bar
Monoscope
Monitor TV
1
2
3
4
Video output
(75 Ω)
Burst signal
(Should be flat)
Fig. 6-2-2 Color Bar Signals of Pattern Generator
EURO : CN540
VIDEO LINE IN
Pattern generator
Approx.
0.3 V
EURO : CN540
VIDEO LINE OUT
Fig. 6-2-1
6-1
SP
LP
Audio signal
Normal
Hi-Fi
400Hz
(L/R)
400Hz
2-1-5. Input/Output Levels and Impedance
Video input: LINE IN
EURO
Input signal: 1Vp-p, 75ohms, unbalanced,
sync negative
Video output: LINE OUT
EURO
Output signal: 1Vp-p, 75ohms, unbalanced,
sync negative
Audio input: LINE IN
EURO
Input level: –7.5 dBs
(0dBs= 0.775Vrms)
Input impedance: more than 47 kilohms
Audio output: LINE OUT
EURO
Standard level: –7.5dBs at load impedance 47
kilohms
Output impedance: less than 10 kilohms
2-2.
POWER SUPPLY CHECK
2-2-1. Output Voltage Check (MA-316 Board)
Mode
E-E
2-1-6. Adjustment Sequence
The adjustments should be performed in the following sequence.
2-3.
SERVO SYSTEM CHECK
Unless otherwise specified, set the switches to the following
positions.
Measuring Instrument
TUNER 30V Check
Digital voltmeter
Measurement point
Specified value
D702 Cathode
33 ± 2V
VCC 12V Check
Measurement point
IC530 Pin 2
Specified value
D 5V Check
12.0 ± 0.3V
Measurement point
Specified value
D160 Cathode
5.2 ± 0.3V
[Check Method]
1) Each of these supply voltages must meet its specified value.
Power Supply Check
• INPUT SELECT switch ................................................. LINE 1
• TAPE SPEED switch ............................................................ SP
2-3-1.
RF Switching Position/
AF Switching Position Adjustments
(MA-316, RP-231 Boards)
[Adjustment Purpose]
To adjust the link of the A-ch and B-ch of the tape playback outputs.
To make the unit compatible with other tapes and units. If this
specification is not satisfied, the link will appear on the screen and
the screen will be disrupted, etc.
Servo System Adjustments
Audio System Adjustments
Video System Adjustments
6-2
Mode
Signal
Playback
Alignment tape: SP color bar portion
Measurement point
Measuring instrument
CH1: Video LINE OUT
(RF switching position)
CN341 pin 1 (HF ADJ)
(AF switching position)
(RP-231 board)
CH2: CN261 pin 3 (RF SWP)
(RP-231 board)
Oscilloscope
Specified value
6.5 ± 0.5H (416 ± 32 µsec)
2-4.
VIDEO SYSTEM CHECKS
For the video system checks, follow the checking procedures given
below as a rule. The color bar video signal supplied from the pattern
generator is used as the video input signal for the video system
adjustment of the recording mode. Check that the signal satisfies
the specified value designated in the “Check of input signal” (Fig.
6-2-2)
Unless otherwise specified, set the switches to the following
positions.
[Adjustment Method]
1) Short-circuit between pin 5 (AV ADJ) and 3 (GND) of CN261
for about 1 second to activate the RF switching position
adjustment mode.
2) Check that “AF” is indicated on FL display.
3) Using the program + and – buttons, adjust to 416 ± 32µsec
(6.5 ± 0.5H).
4) Press the PAUSE button.
5) The set goes to the AF switching position adjustment mode.
CH1
Approx.
1Vp-p
CH2
Approx.
5Vp-p
• INPUT SELECT switch ................................................. LINE 1
• TAPE SPEED switch ............................................................ SP
[Checking Sequence]
1) X’tal OSC Check
2) SYNC AGC Check
3) White clip/Dark clip Check
4) Recording Y Level Check
5) Recording Chroma Level Check
6) Playback Level Check
V
Enlargement
Vertical sync. signal
2-4-1.
Mode
CH1
CH2
(CN261 PIN 2
(RF SWP))
(RP-231)
6.5 ± 0.5H
(416 ± 32 µsec)
Fig. 6-2-3
6)
7)
8)
9)
X’tal OSC Check (MA-316 Board)
Playback
Signal
Measurement point
Alignment tape: SP Color bar portion
Q211 Emitter
Measuring instrument
Specified value
Oscilloscope and Frequency counter
4,433,619 ± 96Hz
Note: A frequency counter should be connected through a buffer
amplifier (oscilloscope, etc.) having a high impedance and
a low capacitance.
Check that “AH” is indicated on FL display.
Using the program + and – buttons, minimize a chipped portion.
At this time, confirm that a noisy sound is not heard.
Press the PAUSE button.
Press the EJECT button.
[Check Method]
1) Check that the oscillation frequency satisfies the specified value
and that the oscillation voltage is 500 ± 200mVp-p.
CH2
RF SWP
(CN261 PIN 2)
(RP-231)
500 ± 200mVp-p
OK
CH1
HF ADJ
(CN341
PIN 1)
(RP-231)
NG
4,443,619 ± 96Hz
Fig. 6-2-5
Should be minimized
RF signal dropout
Fig. 6-2-4
6-3
2-4-2.
Mode
SYNC AGC Check (MA-316 Board)
E-E
2-4-4.
Mode
Recording Y Level Check (MA-316 Board)
E-E
Signal
Measurement point
Color bar
IC201 pin #•
Signal
Measurement point
No-signal
IC201 pin !•
Measuring instrument
Specified value
Oscilloscope
A=2.1 ± 0.1Vp-p
Measuring instrument
Specified value
Oscilloscope
A=307 ± 50mVp-p
[Check Method]
1) Check that the Video signal level (A) satisfies the specified
value.
[Check Method]
1) Check that the recording RF signal satisfies the specified value.
A
A
H
Fig. 6-2-8
2-4-5.
Fig. 6-2-6
2-4-3.
Mode
Mode
White Clip/Dark Clip Check (MA-316 Board)
E-E
Signal
Measurement point
Color bar
IC201 pin #¶
Measuring instrument
Specified value
Oscilloscope
White clip : 190 ± 15%
Dark clip : 58.5 ± 5%
Recording Chroma Level Check
(MA-316 Board)
Recording
Signal
Measurement point
Color bar
IC201 pin !¢
Measuring instrument
Specified value
Oscilloscope
A=350 ± 40mV
[Check Method]
1) Confirm the amplitude of recording chroma level becomes the
specified value.
Connect a resistor of 3.3kΩ between IC201 pin $™ and GND.
[Check Method]
1) Check that the white clip level is 190 ± 15% to the white (100%)
level.
2) Check that the dark chip level is 58.5 ± 5% to the white (100%)
level.
A
Fig. 6-2-9
White (100%)
A
100%
B
H
Fig. 6-2-7
6-4
2-4-6.
Mode
Playback Level Check (MA-316 Board)
Playback
Signal Alignment
Measurement point
Alignment tape : SP mode color bar
portion
Video LINE OUT terminal
Measuring instrument
Specified value
Oscilloscope
A=1.0 ± 0.1Vp-p (75Ω terminated)
2-5-1. ACE Head Adjustment
Refer to the “VHS mechanical adjustment manual
11).
2-5-2.
Mode
Measurement point
Measuring instrument
Specified value
RP-231 BOARD (Conductor side)
1
5
2
1
CN341
CN261
400Hz, –7.5dBs : J480 (LINE IN 2)
on FR-128 board
J500 (AUDIO OUT), CN500 (LINE 1)
RF/AF
Switching Position
Audio level meter
J500 : –7.5 ± 2.0dBs,
CN500 : –6.3 ± 2.0dBs
[Check Method]
1) Input signal of 400Hz and –7.5dBs to J480 (LINE IN 2).
2) Check that the audio output level is the specified value.
A
2-5-3.
H
Fig. 6-2-10
Mode
Overall Output Level and Distortion Factor
Check
Self-record playback
Signal
2-5.
AUDIO SYSTEM ADJUSTMENT
• For the adjustment of the audio system, perform in the SP mode
if there is no special notes. Use the alignment tape.
Measurement point
Measuring instrument
[Connecting Instruments]
Specified value
(CN500 or J500)
Audio line OUTPUT L/R
(J480)
Audio line
INPUT L/R
Audio level meter
or distortion meter
47 kΩ
600 Ω
Audio
oscillator
ADJUSTMENT PARTS LOCATION DIAGRAM
E-E Output Level Check
E-E
Signal
[Check Method]
1) Check that the playback level satisfies the specified value.
2-6.
” (9-921-647-
400Hz, –7.5dBs : J480 (LINE IN 2)
on FR-128 board
CN500 (LINE 1) Pin 3 (L), Pin 1 (R)
Audio level meter and Distortion
meter
Playback Level: –6.3 ± 3dBs
Distortion: 4.0% or less
MA-316 BOARD (Conductor side)
20
2
21
1
J500
CN500
LINE 1
AUDIO OUT
IC530
[Check Method]
1) Input signal of 400Hz and –7.5dBs to J480 (LINE IN 2).
2) Record signal.
3) Playback the recorded portion.
4) Check that the output level is –6.3 ± 3dBs.
5) Check that the distortion factor is 4.0% or less.
Attenuator
VTR
2-5-4.
Fig. 6-2-11
• Adjust in the SP mode if there is no special indications.
• Perform the adjustment setting the switch on the following
positions.
• INPUT SELECT switch ........................................... LINE IN 2
[Adjustment Method]
1. ACE head adjustment.....Refer to the VHS mechanical
adjustment manual .
2. E-E output level check
3. Overall Output level and distortion factor check
4. Overall noise level check.
Overall Noise Level Check
Mode
Signal
Self-record playback
No signal (Insert a shorting plug into
the Audio LINE IN terminal)
Measurement point
Measuring instrument
CN500 (LINE 1) Pin 3
Audio level meter (IHF-A weighing
filter is used)
Specified value
– 45.5dBs or less
25
24
4
40
41
IC201
1
SYNC AGC
White/Dark Clips
REC Y Level
REC C Level
80
Q211
64
1
Tuner
30V
65
E
X'tal OSC
IC160
[Check Method]
1) Record.
2) Playback recorded portion.
3) Check that noise level is – 45.5dBs or less.
D160
D5V
6-5
D702
VCC 12V
6-6E
SLV-E830B/E830NP/E830VC1/E830VC2
SECTION 7
REPAIR PARTS LIST
7-1. EXPLODED VIEWS
Note:
• -XX, -X mean standardized parts, so they may
have some differences from the original one.
• Items marked “*” are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering these
items.
•
The mechanical parts with no reference number
in the exploded views are not supplied.
The components identified by mark ! or
dotted line with mark ! are critical for safety.
Replace only with part number specified.
7-1-1. FRONT PANEL ASSEMBLY AND UPPER CASE SECTION
8
7
24
23
22
21
14
15
7
3
5
13
16
15
9
15
12
6
15
10
11
4
2
Ref. No.
1
Part No.
Description
1
2
2
3
3
3-979-310-21
3-979-309-21
3-979-309-31
X-3948-225-1
X-3948-402-1
RING (AV), JO
BUTTON (AV), CENTER (NP,VC1,VC2)
BUTTON (AV), CENTER (B)
PANEL ASSY, FRONT (VC1,VC2)
PANEL ASSY, FRONT (B)
3
4
5
6
* 8
X-3948-403-1
X-3948-226-1
3-953-432-01
3-979-302-21
3-987-684-21
PANEL ASSY, FRONT (NP)
DOOR ASSY, FRONT
SPRING (GE), FL
DOOR (AV), CASSETTE
CASE (BN), UPPER
!9
* 10
11
12
1-782-012-11
A-6794-519-A
1-762-844-31
1-783-169-11
CORD, POWER
DM-73 BOARD, COMPLETE
SWITCH, ROTARY
CABLE, FLAT (FFD-2)
Remarks
Ref. No.
Part No.
Description
* 13
* 13
* 13
14
15
A-6791-533-A
A-6791-535-A
A-6794-520-A
1-783-167-11
3-968-554-01
FR-128 BOARD, COMPLETE (VC1,VC2)
FR-128 BOARD, COMPLETE(B)
FR-128 BOARD, COMPLETE(NP)
CABLE, FLAT (FFM-18)
SCREW (WN1411 D2.5 EJOT K25)
16
21
7-1
Remarks
21
22
23
3-987-691-01 KNOB, SLIDE
1-475-564-11 COMMANDER, STANDARD (RMT-V224)
(NP,VC1,VC2)
1-475-564-31 COMMANDER, STANDARD(RMT-V224B) (B)
3-709-126-01 COVER, BATTERY
3-972-783-21 RING, JOG
24
24
3-972-850-01 BUTTON, FUNCTION (NP,VC1,VC2)
3-972-850-21 BUTTON, FUNCTION (B)
7-1-2. CHASSIS SECTION
#1
57
53
54
#1
#1
58
56
57
SLV-E830B
#1
52
55
#2
51
Not supplied
Ref. No.
*
*
*
*
51
52
52
52
53
Part No.
Description
3-959-381-01
A-6791-536-A
A-6791-530-A
A-6791-534-A
A-6791-531-A
BASE (L), MD
MA-316 BOARD, COMPLETE (NP)
MA-316 BOARD, COMPLETE (VC1,VC2)
MA-316 BOARD, COMPLETE (B)
RP-231 BOARD, COMPLETE
Remarks
Ref. No.
Part No.
Description
! 54
* 55
56
57
* 58
1-468-273-11
3-987-710-61
1-779-725-11
3-970-608-21
A-6791-537-A
POWER BLOCK
PANEL (BN), REAR
CONNECTOR, BOARD TO BOARD 5P
SUMITITE (B3), +BV
SE-69 BOARD, COMPLETE (B)
Note :
7-2
Remarks
The components identified by mark ! or dotted
line with mark ! are critical for safety.
Replace only with part number specified.
7-1-3. MECHANISM DECK-1
707
#701
710
708
709
706
not supplied
723
704
712
711
703
705
702
722
701
713
720
701
716
721
714
719
715
717
718
#701
Ref. No.
724
Part No.
Description
Part No.
Description
701
702
703
704
705
3-977-509-01
3-977-507-01
3-977-508-01
1-500-144-11
3-977-495-01
WASHER, THRUST
TABLE, REEL (S) (GRAY)
TABLE, REEL (T) (BLACK)
HEAD, FE
SHAFT TG2
Remarks
Ref. No.
713
714
715
716
717
3-977-447-01
3-977-514-01
3-977-441-01
3-977-445-01
3-977-465-01
GEAR, ELEVATOR
OPENER, LID
GEAR, PINCH PRESSING
GEAR, TG8 ARM DRIVING
SPRING,EXTENSION(RVS BRAKE)
706
707
708
709
710
3-977-494-01
A-6759-619-C
3-977-535-01
3-977-536-01
3-970-471-01
HOLDER, FEH
FL COMPLETE ASSY
PLATE, LUMINOUS(END SENSOR)
PLATE, LUMINOUS(TOP SENSOR)
SPRING (DECK OPEN), TORSION
718
719
720
721
722
X-3947-582-1
3-977-446-01
X-3947-590-1
A-6759-620-A
3-974-556-01
ARM ASSY, RVS BRAKE
GEAR, TG8 ARM
TG8 ASSY
HEAD BLOCK ASSY, ACE (TDK)
+ HEXA TT 2.6X9 (TAPER)
711
712
A-6759-615-A PRESS BLOCK ASSY, PINCH
3-958-455-01 SPRING (PINCH), TENSION
723
724
3-979-508-01 SCREW
3-978-485-01 PLATE, GUIDE CASSETTE
7-3
Remarks
7-1-4. MECHANISM DECK-2
#701
767
770
771
769
772
761
#701
764
760
763
762
758
759
762
773
757
763
#702
766
756
774
765
755
754
752
753
751
Ref. No.
Part No.
Description
Part No.
Description
751
752
753
754
755
X-3947-581-1
3-977-462-01
X-3947-573-1
X-3947-580-2
3-977-513-02
BRAKE ASSY,MAIN(T)
SPRING,EXTENTION. (MAIN BRAKE)
ARM ASSY, PENDULUM
BRAKE ASSY, MAIN(S)
LEVER, REC. PROOF
Remarks
Ref. No.
764
765
766
767
768
3-969-632-04
A-6750-325-E
3-977-501-01
X-3943-899-8
2-643-205-01
BASE, DRUM
SHUTTLE (T) BLOCK ASSY
PLATE, LUMINOUS
GROUND ASSY, SHAFT
SCREW
756
757
758
759
760
3-976-767-01
3-977-487-01
X-3947-587-1
X-3947-589-1
3-977-488-01
SPRING, TENS. (REC. PROOF)
BOSS, TG1 FULCRUM
TG1 ASSY
BAND ASSY, TG1
SPRING (POWER TENSION)
769
769
770
771
1-759-373-11
1-759-557-11
A-6746-074-G
X-3947-255-1
DRUM ASSY DZH-86A-R (NP,VC1,VC2)
DRUM ASSY DZH-98A-R (B)
ROLLER BLOCK ASSY, HC
ROLLER ASSY, HC
761
762
763
A-6750-324-E SHUTTLE (S) BLOCK ASSY
X-3944-378-2 ROLLER ASSY, GUIDE
3-965-178-01 SPRING
772
773
774
3-975-724-07 ARM, HC
X-3946-855-1 SHUTTLE (S) ASSY
X-3946-856-1 SHUTTLE (T) ASSY
7-4
Remarks
7-1-5. MECHANISM DECK-3
816
815
817
M902
803
818
803
814
#701
812
813
828
811
829
820
810
808
809
819
827
821
826
807
805
822
806
804
823
824
M903
803
801
825
802
#703
Ref. No.
Part No.
Description
* 801
802
803
804
805
3-977-437-01
X-3947-584-1
3-977-443-01
3-977-438-01
3-977-506-01
RETAINER,CAM MOTOR
ASSY, REEL DIRECT
WASHER, STOPPER
WORM - WHEEL
ARM, LIMITTER SELECTION
806
807
808
809
810
3-977-444-01
3-977-515-01
3-977-517-01
3-977-519-01
3-977-518-02
811
812
813
814
815
3-977-516-01
3-977-877-01
3-977-504-01
X-3947-585-1
3-977-510-01
816
3-977-440-01 WASHER, STOPPER
Remarks
Ref. No.
Part No.
Description
817
818
819
820
821
3-977-439-01
3-977-442-01
3-977-455-01
3-977-456-03
X-3947-579-1
GEAR, CAM
SLIDER
GEAR, LOADING(T)
SPRING, TORSION (LOAD T)
LEVER ASSY, LOADING(T)
GEAR, PINCH TRANSMISSION
GUIDE, FL SLIDER
PLATE, SLIDE, FL
SPRING, TENS. (LIMIT, FL)
PLATE, LIMITTER, FL
822
823
824
825
826
3-977-451-01
3-977-452-01
X-3947-578-1
X-3947-576-2
3-977-468-01
GEAR, LOADING(S)
SPRING, TORSION (LOAD S)
LEVER ASSY, LOADING(S)
CHASSIS ASSY, MECHANICAL
SHAFT, CAPSTAN BRAKE
HOLDER, FL SLIDER
PLATE, RETAINER
GEAR, CLUTCH
GEAR ASSY, PULLEY
BELT, RUBBER
827
828
829
830
M902
3-977-467-02
X-3947-583-1
3-977-489-01
A-6759-616-A
1-698-971-11
SPRING, CAP BRAKE
BRAKE ASSY, CAPSTAN
ARM, TG1 DRIVING
GEAR BLOCK ASSY, LOADING
MOTOR, DC
M903
X-3947-577-1 MOTOR ASSY, CAM
7-5
Remarks
DM-73
FR-128
7-2. ELECTRICAL PARTS LIST
Note:
•
When indicating parts by reference number,
please include the board name.
The components identified by mark ! or
dotted line with mark ! are critical for safety.
Replace only with part number specified.
•
•
•
Due to standardization, replacements in the
parts list may be different from the parts
specified in the diagrams or the components
used on the set.
-XX, -X mean standardized parts, so they may
have some difference from the original one.
Items marked “*” are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering these
items.
CAPACITORS:
uF: µF
Ref. No.
Part No.
Description
Remarks
Ref. No.
*
A-6794-519-A DM-73 BOARD, COMPLETE
*********************
(Ref.No.:2,000 series)
< CONNECTOR >
CN451
CN452
1-784-484-11 CONNECTOR, FFC/FPC 5P
1-784-453-11 CONNECTOR, FFC/FPC 11P
< DIODE >
D459
•
•
RESISTORS
All resistors are in ohms.
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F: nonflammable
COILS
uH: µH
SEMICONDUCTORS
In each case, u: µ, for example:
uA...: µA... , uPA... , µPA... ,
uPB... , µPB... , uPC... , µPC... ,
uPD..., µPD...
Part No.
Description
Remarks
C192
C193
C196
C198
C199
1-126-924-11
1-163-031-11
1-126-916-11
1-163-031-11
1-163-031-11
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
330uF
0.01uF
1000uF
0.01uF
0.01uF
C200
C400
C421
C422
C423
1-163-038-91
1-163-809-11
1-165-319-11
1-124-589-11
1-163-031-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
0.1uF
0.047uF
0.1uF
47uF
0.01uF
C424
C481
C491
C493
C495
1-165-319-11
1-163-009-11
1-163-009-11
1-163-009-11
1-163-038-91
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.001uF
0.001uF
0.001uF
0.1uF
C496
1-163-038-91 CERAMIC CHIP
20%
20%
10%
20%
10V
50V
6.3V
50V
50V
25V
25V
50V
16V
50V
8-719-056-06 DIODE SLR-342DCT31
< TRANSISTOR >
Q450
•
8-729-424-08 TRANSISTOR UN2111
10%
10%
10%
50V
50V
50V
50V
25V
< RESISTOR >
R459
R464
R465
R466
R467
1-216-033-00
1-216-057-00
1-216-073-00
1-249-429-11
1-216-057-00
METAL CHIP
METAL CHIP
METAL CHIP
CARBON
METAL CHIP
220
2.2K
10K
10K
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/4W
1/10W
R468
R469
R470
R471
R472
1-216-057-00
1-216-057-00
1-216-073-00
1-216-061-00
1-216-065-91
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
RES,CHIP
2.2K
2.2K
10K
3.3K
4.7K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
0.1uF
25V
< CONNECTOR >
CN181
CN400
* CN480
1-784-514-11 CONNECTOR, FFC/FPC 35P
1-784-453-11 CONNECTOR, FFC/FPC 11P
1-564-004-11 PIN, CONNECTOR 5P
< TRIMMER >
CT180
1-141-227-00 CAP, TRIMMER
20PF
< DIODE >
< SWITCH >
S451
1-762-196-21 SWITCH, TACT (REC)
S453
1-762-196-21 SWITCH, TACT (REW)
S457
1-762-196-21 SWITCH, TACT (FF)
S458
1-762-196-21 SWITCH, TACT (PAUSE)
S459
1-762-196-21 SWITCH, TACT (JOG)
************************************************************
A-6794-520-A FR-128 BOARD, COMPLETE (NP)
***************************
A-6791-533-A FR-128 BOARD, COMPLETE (VC1,VC2)
********************************
A-6791-535-A FR-128 BOARD, COMPLETE (B)
**************************
(Ref.No.:3,000 series)
*
*
*
< BUZZER >
BZ181
1-529-104-11 BUZZER, PIEZOELECTRIC
D186
D187
D400
D420
D480
8-719-200-82
8-719-200-82
8-719-056-07
8-719-110-08
8-719-109-97
D481
D490
D491
8-719-108-12 DIODE RD9.1E-W
8-719-108-12 DIODE RD9.1E-W
8-719-108-12 DIODE RD9.1E-W
1-163-031-11
1-163-104-00
1-163-104-00
1-125-705-11
1-163-038-91
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
DOUBLE LAYER
CERAMIC CHIP
11ES2
11ES2
SLR-342MCT31
RD8.2ES-B2
RD6.8ES-B2
< IC >
IC180
IC180
IC182
IC183
IC400
8-759-483-32
8-759-483-33
8-759-432-34
8-759-248-87
8-749-011-05
IC420
8-759-438-82 IC uPD16311GC-AB6
IC
IC
IC
IC
IC
S579C15PJ-VSX9373 (NP,VC1,VC2)
S579C15PJ-VSX9374 (B)
ST24W16FM6TR
MM1256XF-BE
GP1U28X
< JACK >
< CAPACITOR >
C180
C188
C189
C190
C191
DIODE
DIODE
DIODE
DIODE
DIODE
0.01uF
30PF
30PF
0.22F
0.1uF
5%
5%
0
50V
50V
50V
5.5V
25V
J480
7-6
1-580-845-11 JACK, PIN 3P (LINE 2 IN)
FR-128
Ref. No.
Part No.
Description
Remarks
Ref. No.
< JUMPER RESISTOR >
JR101
JR102
JR103
JR104
JR105
1-216-295-91
1-216-295-91
1-216-295-91
1-216-296-91
1-216-296-91
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
JR106
JR107
JR108
JR109
JR110
1-216-296-91
1-216-296-91
1-216-296-91
1-216-296-91
1-216-296-91
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
JR111
JR181
JR190
JR191
JR192
1-216-295-91
1-216-295-91
1-216-296-91
1-216-295-91
1-216-295-91
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
< JUMPER RESISTOR >
JS181
JS490
1-216-295-91 SHORT
1-216-295-91 SHORT
0
0
< COIL >
L182
1-414-934-21 INDUCTOR
10uH
MA-316
Part No.
Description
R404
R405
R406
R407
R408
1-216-073-00
1-216-073-00
1-216-073-00
1-216-073-00
1-216-061-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
10K
10K
3.3K
5%
5%
5%
5%
5%
Remarks
1/10W
1/10W
1/10W
1/10W
1/10W
R409
R410
R411
R415
R416
1-216-065-91
1-216-073-00
1-216-081-00
1-216-075-00
1-216-073-00
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
10K
22K
12K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R417
R418
R421
R422
R423
1-216-295-91
1-216-073-00
1-216-295-91
1-216-049-91
1-216-049-91
SHORT
0
METAL CHIP
SHORT
0
RES,CHIP
RES,CHIP
10K
5%
1/10W
1K
1K
5%
5%
1/10W
1/10W
R424
R425
R426
R427
R428
1-216-049-91
1-216-085-00
1-216-073-00
1-216-069-00
1-216-073-00
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
33K
10K
6.8K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R429
R430
R480
R481
R490
1-216-065-91
1-216-073-00
1-216-022-00
1-216-295-91
1-216-295-91
RES,CHIP
METAL CHIP
METAL CHIP
SHORT
0
SHORT
0
4.7K
10K
75
5%
5%
5%
1/10W
1/10W
1/10W
R491
R492
R493
R494
1-216-295-91
1-216-035-00
1-216-089-91
1-216-295-91
SHORT
0
METAL CHIP
RES,CHIP
SHORT
0
270
47K
5%
5%
1/10W
1/10W
< FLUORESCENT INDICATOR >
ND420
1-517-745-21 TUBE, FLUORESCENT INDICATOR
< TRANSISTOR >
Q400
8-729-421-19 TRANSISTOR UN2213
< SWITCH >
< RESISTOR >
R180
R181
R182
R183
R184
1-216-073-00
1-216-073-00
1-216-295-91
1-216-295-91
1-216-113-00
METAL CHIP
METAL CHIP
SHORT
0
SHORT
0
METAL CHIP
10K
10K
5%
5%
1/10W
1/10W
470K
5%
1/10W
R185
R186
R187
R188
R190
1-216-073-00
1-216-041-00
1-216-041-00
1-216-049-91
1-249-417-11
METAL CHIP
METAL CHIP
METAL CHIP
RES,CHIP
CARBON
10K
470
470
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/4W F
R191
R192
R195
R196
R197
1-216-073-00
1-216-049-91
1-216-049-91
1-216-049-91
1-216-049-91
METAL CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
10K
1K
1K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R198
R199
R201
R202
R203
1-216-049-91
1-216-037-00
1-216-295-91
1-216-095-00
1-216-113-00
RES,CHIP
METAL CHIP
SHORT
0
METAL CHIP
METAL CHIP
1K
330
5%
5%
1/10W
1/10W
82K
470K
5%
5%
1/10W
1/10W
R204
R400
R401
R402
R403
1-218-179-11
1-216-029-00
1-216-089-91
1-216-065-91
1-216-073-00
RES,CHIP
METAL CHIP
RES,CHIP
RES,CHIP
METAL CHIP
10M
150
47K
4.7K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
S400
S401
S402
S404
S406
1-762-196-21
1-762-196-21
1-762-196-21
1-762-196-21
1-762-196-21
SWITCH, TACT (ON/STANDBY)
SWITCH, TACT (PROGRAM/TRACKING:+)
SWITCH, TACT (AUTO SET UP)
SWITCH, TACT (PROGRAM/TRACKING:-)
SWITCH, TACT (QUICK TIMER)
S407
S408
S411
1-762-196-21 SWITCH, TACT (EJECT)
1-762-196-21 SWITCH, TACT (AUDIO DUB)
1-571-588-31 SWITCH, SLIDE (POWER SAVE)
< VIBRATOR >
X180
1-760-014-11 VIBRATOR, CERAMIC 20MHz
X181
1-579-463-11 VIBRATOR, CRYSTAL 32.768kHz
************************************************************
A-6791-530-A MA-316 BOARD, COMPLETE (VC1,VC2)
********************************
A-6791-534-A MA-316 BOARD, COMPLETE (B)
**************************
A-6791-536-A MA-316 BOARD, COMPLETE (NP)
***************************
(Ref.No.:2,000 series)
*
*
*
1-558-924-21 CABLE, PIN
3-960-273-01 SPACER, TOP END
3-960-274-01 SPACER, LED
*
*
< CAPACITOR >
C100
C101
C102
C103
C104
7-7
1-128-057-11
1-163-009-11
1-163-009-11
1-163-009-11
1-163-009-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
330uF
0.001uF
0.001uF
0.001uF
0.001uF
20%
10%
10%
10%
10%
6.3V
50V
50V
50V
50V
MA-316
Ref. No.
Part No.
Description
C105
C107
C108
C109
C130
1-164-232-11
1-130-489-00
1-137-441-11
1-126-157-11
1-163-031-11
CERAMIC CHIP
MYLAR
FILM
ELECT
CERAMIC CHIP
0.01uF
0.033uF
0.027uF
10uF
0.01uF
Remarks
5%
5%
20%
50V
50V
50V
16V
50V
C131
C132
C134
C159
C160
1-163-031-11
1-124-589-11
1-124-463-00
1-163-809-11
1-163-038-91
CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
0.01uF
47uF
0.1uF
0.047uF
0.1uF
20%
20%
10%
50V
16V
50V
25V
25V
C161
C162
C164
C165
C166
1-124-589-11
1-163-251-11
1-163-229-11
1-163-229-11
1-163-038-91
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
47uF
100PF
12PF
12PF
0.1uF
20%
5%
5%
5%
16V
50V
50V
50V
25V
C167
C170
C172
C173
C201
1-124-589-11
1-126-154-11
1-164-346-11
1-163-121-00
1-109-982-11
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
47uF
47uF
1uF
150PF
1uF
20%
20%
16V
6.3V
16V
50V
10V
C202
C204
C205
C206
C207
1-163-809-11
1-163-031-11
1-163-037-11
1-164-232-11
1-164-232-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.047uF
0.01uF
0.022uF
0.01uF
0.01uF
10%
10%
25V
50V
25V
50V
50V
C208
C209
C210
C211
C212
1-163-241-11
1-128-131-11
1-163-131-00
1-163-237-11
1-163-259-91
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
39PF
22uF
390PF
27PF
220PF
5%
20%
5%
5%
5%
50V
50V
50V
50V
50V
C213
C214
C217
C219
C220
1-163-257-11
1-163-235-11
1-109-982-11
1-163-038-91
1-109-982-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
180PF
22PF
1uF
0.1uF
1uF
5%
5%
10%
50V
50V
10V
25V
10V
C222
C223
C224
C226
C228
1-163-038-91
1-126-154-11
1-162-306-11
1-163-038-91
1-126-157-11
CERAMIC CHIP
ELECT
CERAMIC
CERAMIC CHIP
ELECT
0.1uF
47uF
0.01uF
0.1uF
10uF
C229
C230
C231
C232
C233
1-162-306-11
1-124-589-11
1-126-157-11
1-109-982-11
1-109-982-11
CERAMIC
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
0.01uF
47uF
10uF
1uF
1uF
C234
C235
C236
C237
C238
1-164-232-11
1-164-232-11
1-126-160-11
1-163-031-11
1-162-306-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC
0.01uF
0.01uF
1uF
0.01uF
0.01uF
C239
C240
C241
C242
C243
1-124-584-00
1-109-982-11
1-163-037-11
1-109-982-11
1-163-031-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100uF
1uF
0.022uF
1uF
0.01uF
20%
10%
10%
10%
10V
10V
25V
10V
50V
C244
C245
C246
C247
C248
1-107-725-11
1-163-809-11
1-109-982-11
1-163-809-11
1-163-031-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.047uF
1uF
0.047uF
0.01uF
10%
10%
10%
10%
16V
25V
10V
25V
50V(B)
5%
10%
10%
20%
25V
6.3V
16V
25V
16V
30%
20%
20%
10%
10%
16V
16V
16V
10V
10V
20%
50V
50V
50V
50V
16V
20%
30%
30%
Ref. No.
7-8
Part No.
Description
Remarks
C248
1-216-065-91 RES,CHIP
4.7K
5%
1/10W
(NP,VC1,VC2)
20%
6.3V
25V
25V
50V
C249
C250
C251
C252
1-126-154-11
1-163-038-91
1-163-038-91
1-164-232-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
47uF
0.1uF
0.1uF
0.01uF
C253
C254
C255
C257
C301
1-163-038-91
1-163-038-91
1-163-038-91
1-163-038-91
1-164-159-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
C302
C305
C306
C307
C308
1-126-154-11
1-109-982-11
1-109-982-11
1-126-157-11
1-124-589-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
47uF
1uF
1uF
10uF
47uF
20%
10%
10%
20%
20%
6.3V
10V
10V
16V
16V
C309
C310
C311
C312
C313
1-126-163-11
1-163-011-11
1-163-011-11
1-137-370-11
1-126-157-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
FILM
ELECT
4.7uF
0.0015uF
0.0015uF
0.01uF
10uF
20%
10%
10%
5%
20%
50V
50V
50V
50V
16V
C314
C315
C317
C318
C361
1-164-232-11
1-126-160-11
1-126-163-11
1-124-589-11
1-126-960-11
CERAMIC CHIP
ELECT
ELECT
ELECT
ELECT
0.01uF
1uF
4.7uF
47uF
1uF
20%
20%
20%
20%
50V
50V
50V
16V
50V
C362
C363
C364
C365
C366
1-126-960-11
1-126-960-11
1-126-960-11
1-126-960-11
1-126-960-11
ELECT
ELECT
ELECT
ELECT
ELECT
1uF
1uF
1uF
1uF
1uF
20%
20%
20%
20%
20%
50V
50V
50V
50V
50V
C369
C370
C371
C372
C373
1-126-964-11
1-126-964-11
1-126-964-11
1-126-964-11
1-126-964-11
ELECT
ELECT
ELECT
ELECT
ELECT
10uF
10uF
10uF
10uF
10uF
20%
20%
20%
20%
20%
50V
50V
50V
50V
50V
C374
C375
C376
C377
C378
1-126-960-11
1-164-489-11
1-163-016-00
1-126-967-11
1-126-964-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
1uF
0.22uF
0.0039uF
47uF
10uF
20%
10%
10%
20%
20%
50V
16V
50V
50V
50V
C379
C380
C381
C382
C383
1-126-961-11
1-126-964-11
1-126-967-11
1-163-016-00
1-164-489-11
ELECT
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
2.2uF
10uF
47uF
0.0039uF
0.22uF
20%
20%
20%
10%
10%
50V
50V
50V
50V
16V
C384
C385
C386
C390
C391
1-163-037-11
1-126-933-11
1-163-037-11
1-126-960-11
1-163-037-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
0.022uF
100uF
0.022uF
1uF
0.022uF
10%
20%
10%
20%
10%
25V
16V
25V
50V
25V
C392
C393
C394
C395
C500
1-126-960-11
1-126-960-11
1-126-960-11
1-126-960-11
1-163-017-00
ELECT
ELECT
ELECT
ELECT
CERAMIC CHIP
1uF
1uF
1uF
1uF
0.0047uF
20%
20%
20%
20%
5%
50V
50V
50V
50V
50V
C501
C510
C511
C512
C513
1-163-017-00
1-163-031-11
1-126-967-11
1-126-967-11
1-126-935-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
ELECT
0.0047uF
0.01uF
47uF
47uF
470uF
5%
50V
50V
16V
16V
6.3V
25V
25V
25V
25V
50V
20%
20%
20%
MA-316
Ref. No.
Part No.
Description
C530
C531
C532
C541
C542
1-126-967-11
1-107-725-11
1-126-933-11
1-124-584-00
1-107-725-11
ELECT
CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
47uF
0.1uF
100uF
100uF
0.1uF
20%
10%
20%
20%
10%
Remarks
16V
16V
16V
10V
16V
C543
C544
C545
C546
C547
1-107-725-11
1-107-725-11
1-164-489-11
1-107-725-11
1-107-725-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.22uF
0.1uF
0.1uF
10%
10%
10%
10%
10%
16V
16V
16V
16V
16V
C571
C572
C573
C660
C661
1-163-017-00
1-126-964-11
1-126-964-11
1-163-239-11
1-126-967-11
CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
ELECT
0.0047uF
10uF
10uF
33PF
47uF
5%
20%
20%
5%
20%
50V
50V
50V
50V(B)
16V
C662
C663
C665
C667
C668
1-163-031-11
1-107-725-11
1-126-967-11
1-164-505-11
1-163-239-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.1uF
47uF
2.2uF
33PF
C669
C670
C671
C672
C673
1-163-239-11
1-164-505-11
1-163-227-11
1-163-235-11
1-163-235-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
33PF
2.2uF
10PF
22PF
22PF
5%
C674
C675
C676
C677
C678
1-126-967-11
1-163-038-91
1-164-232-11
1-126-960-11
1-126-961-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
47uF
0.1uF
0.01uF
1uF
2.2uF
20%
20%
20%
16V
25V
50V
50V
50V
C679
C680
C681
C682
C701
1-163-037-11
1-163-139-00
1-163-037-11
1-109-982-11
1-126-964-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.022uF
820PF
0.022uF
1uF
10uF
10%
5%
10%
10%
20%
25V
50V
25V
10V
50V
C704
C705
C708
C709
C710
1-126-964-11
1-163-031-11
1-126-967-11
1-163-031-11
1-126-969-11
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
10uF
0.01uF
47uF
0.01uF
220uF
20%
C710
C730
C731
C752
C753
1-126-965-11
1-126-964-11
1-126-964-11
1-126-933-11
1-107-725-11
ELECT
ELECT
ELECT
ELECT
CERAMIC CHIP
C755
C820
C821
C822
C823
1-126-935-11
1-163-017-00
1-163-017-00
1-163-003-11
1-163-003-11
C824
C825
C850
C851
C852
1-126-964-11
1-126-964-11
1-163-038-91
1-126-157-11
1-164-161-11
C853
C855
C856
1-163-989-11 CERAMIC CHIP
1-164-489-11 CERAMIC CHIP
1-163-038-91 CERAMIC CHIP
Ref. No.
Part No.
Description
CN101
CN102
CN104
* CN161
CN164
1-779-724-11
1-779-723-11
1-766-716-11
1-564-004-11
1-784-514-11
CONNECTOR, BOARD TO BOARD 5P
CONNECTOR, BOARD TO BOARD 9P
CONNECTOR, BOARD TO BOARD 3P
PIN, CONNECTOR 5P
CONNECTOR, FFC/FPC 35P
CN165
CN305
* CN306
CN500
CN570
1-506-469-11
1-573-847-11
1-766-718-21
1-784-415-11
1-784-415-11
PIN, CONNECTOR 4P
CONNECTOR, BOARD TO BOARD 15P
CONNECTOR, BOARD TO BOARD 17P
CONNECTOR, SQUARE TYPE 21P (LINE 1(TV))
CONNECTOR, SQUARE TYPE 21P
(DECODER/LINE 3 IN)
CN600
1-569-341-11 CONNECTOR, BOARD TO BOARD 19P
< DIODE >
10%
20%
50V
16V
16V
16V
50V
D102
D107
D108
D131
D132
8-719-048-26
8-719-911-19
8-719-200-82
8-719-200-82
8-719-200-82
DIODE
DIODE
DIODE
DIODE
DIODE
GL528V1
1SS119
11ES2
11ES2
11ES2
D160
D500
D501
D502
D503
8-719-200-82
8-719-109-97
8-719-109-97
8-719-109-97
8-719-109-97
DIODE
DIODE
DIODE
DIODE
DIODE
11ES2
RD6.8ES-B2
RD6.8ES-B2
RD6.8ES-B2
RD6.8ES-B2
D504
D505
D506
D507
D508
8-719-109-97
8-719-109-97
8-719-109-97
8-719-109-97
8-719-109-97
DIODE
DIODE
DIODE
DIODE
DIODE
RD6.8ES-B2
RD6.8ES-B2
RD6.8ES-B2
RD6.8ES-B2
RD6.8ES-B2
D510
D511
D512
D513
D514
8-719-109-97
8-719-109-97
8-719-921-86
8-719-109-97
8-719-109-97
DIODE
DIODE
DIODE
DIODE
DIODE
RD6.8ES-B2
RD6.8ES-B2
MTZJ-13
RD6.8ES-B2
RD6.8ES-B2
50V
50V
20%
16V
50V
20%
50V
(NP,VC1,VC2)
D515
D516
D517
D518
D519
8-719-109-97
8-719-109-97
8-719-108-12
8-719-108-12
8-719-108-12
DIODE
DIODE
DIODE
DIODE
DIODE
RD6.8ES-B2
RD6.8ES-B2
RD9.1E-W
RD9.1E-W
RD9.1E-W
22uF
10uF
10uF
100uF
0.1uF
20%
20%
20%
20%
10%
50V(B)
50V
50V
16V
16V
D540
D541
D542
D543
D544
8-719-109-97
8-719-109-97
8-719-109-97
8-719-109-97
8-719-109-97
DIODE
DIODE
DIODE
DIODE
DIODE
RD6.8ES-B2
RD6.8ES-B2
RD6.8ES-B2
RD6.8ES-B2
RD6.8ES-B2
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
470uF
0.0047uF
0.0047uF
330PF
330PF
20%
5%
5%
10%
10%
6.3V
50V
50V
50V
50V
D570
D571
D572
D573
D574
8-719-109-97
8-719-109-97
8-719-109-97
8-719-109-97
8-719-109-97
DIODE
DIODE
DIODE
DIODE
DIODE
RD6.8ES-B2
RD6.8ES-B2
RD6.8ES-B2
RD6.8ES-B2
RD6.8ES-B2
ELECT
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
10uF
10uF
0.1uF
10uF
0.0022uF
20%
20%
50V
50V
25V
16V
100V
D575
D576
D577
D578
D579
8-719-109-97
8-719-109-97
8-719-109-97
8-719-109-97
8-719-109-97
DIODE
DIODE
DIODE
DIODE
DIODE
RD6.8ES-B2
RD6.8ES-B2
RD6.8ES-B2
RD6.8ES-B2
RD6.8ES-B2
0.033uF
0.22uF
0.1uF
10%
10%
25V
16V
25V
D580
D610
D660
D661
D663
8-719-109-97
8-719-200-82
8-719-911-19
8-719-911-19
8-719-911-19
DIODE
DIODE
DIODE
DIODE
DIODE
RD6.8ES-B2
11ES2
1SS119
1SS119
1SS119
5%
0.5PF
5%
5%
20%
10%
Remarks
< CONNECTOR >
50V
16V
50V
50V
50V
7-9
MA-316
Ref. No.
D702
D750
D800
Part No.
Description
Remarks
Ref. No.
Part No.
Description
< FILTER >
JR026
JR027
JR028
JR029
JR030
1-216-295-91
1-216-296-91
1-216-296-91
1-216-296-91
1-216-295-91
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
8-719-982-26 DIODE MTZJ-33B
8-719-200-82 DIODE 11ES2
8-719-911-19 DIODE 1SS119
Remarks
FL500
FL501
FL502
FL503
FL504
1-236-163-11
1-236-163-11
1-236-163-11
1-236-163-11
1-236-163-11
ENCAPSULATED COMPONENT
ENCAPSULATED COMPONENT
ENCAPSULATED COMPONENT
ENCAPSULATED COMPONENT
ENCAPSULATED COMPONENT
JR031
JR032
JR033
JR034
JR035
1-216-295-91
1-216-295-91
1-216-296-91
1-216-295-91
1-216-296-91
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
FL505
FL570
FL571
FL572
FL573
1-236-163-11
1-236-163-11
1-236-163-11
1-236-163-11
1-236-163-11
ENCAPSULATED COMPONENT
ENCAPSULATED COMPONENT
ENCAPSULATED COMPONENT
ENCAPSULATED COMPONENT
ENCAPSULATED COMPONENT
JR036
JR037
JR038
JR039
JR040
1-216-295-91
1-216-295-91
1-216-295-91
1-216-296-91
1-216-296-91
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
< IC >
JR041
JR042
JR043
JR044
JR045
1-216-295-91
1-216-296-91
1-216-296-91
1-216-296-91
1-216-295-91
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
JR046
JR047
JR048
JR049
JR050
1-216-296-91
1-216-295-91
1-216-296-91
1-216-296-91
1-216-296-91
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
JR051
JR052
JR053
JR054
JR055
1-216-295-91
1-216-296-91
1-216-296-91
1-216-296-91
1-216-295-91
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
JR056
JR057
JR058
1-216-295-91 SHORT
1-216-295-91 SHORT
1-216-295-91 SHORT
0
0
0
IC100
IC141
IC160
IC161
IC201
8-759-702-02
8-759-100-93
8-752-891-51
8-759-481-46
8-759-479-25
IC
IC
IC
IC
IC
NJM062M
uPC393G2
CXP87948-009Q
LB1943
LA71514M-MPB
IC202
IC360
IC530
IC540
IC660
8-759-439-50
8-759-486-63
8-759-438-18
8-759-438-16
8-759-480-24
IC
IC
IC
IC
IC
LC89977M-TE-L
TDA9615H/N1,518
PQ12RD08
STV6400D
MB90089PF-G-VSX9373-BND-ER
IC661
IC820
IC850
8-759-164-09 IC LA7218M-TE-R
8-759-700-07 IC NJM2903M
8-759-484-61 IC SDA5650X-GEG
< JACK >
J500
1-784-414-11 JACK, PIN 2P (AUDIO OUT)
< JUMPER RESISTOR >
< JUMPER RESISTOR >
JR001
JR002
JR003
JR004
JR005
1-216-296-91
1-216-295-91
1-216-295-91
1-216-295-91
1-216-296-91
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
JS201
JS390
JS391
JR006
JR007
JR008
JR009
JR010
1-216-296-91
1-216-296-91
1-216-296-91
1-216-295-91
1-216-295-91
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
L141
L161
L162
L201
L202
1-414-940-21
1-414-934-21
1-414-934-21
1-414-946-21
1-414-940-21
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
100uH
10uH
10uH
39uH
100uH
JR011
JR012
JR013
JR014
JR015
1-216-295-91
1-216-295-91
1-216-296-91
1-216-295-91
1-216-296-91
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
L203
L204
L205
L206
L207
1-469-014-21
1-414-934-21
1-408-982-11
1-414-934-21
1-414-934-21
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
120uH
10uH
100uH
10uH
10uH
JR016
JR017
JR018
JR019
JR020
1-216-295-91
1-216-296-91
1-216-296-91
1-216-296-91
1-216-296-91
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
L301
L361
L510
L530
L540
1-414-940-21
1-414-940-21
1-414-940-21
1-414-940-21
1-414-934-21
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
100uH
100uH
100uH
100uH
10uH
JR021
JR022
JR023
JR024
JR025
1-216-295-91
1-216-295-91
1-216-296-91
1-216-296-91
1-216-295-91
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
L660
L662
L663
L664
L701
1-414-186-31
1-414-940-21
1-414-940-21
1-412-470-21
1-414-930-21
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
33uH
100uH
100uH
22uH
2.2uH
1-216-295-91 SHORT
1-216-296-91 SHORT
1-216-296-91 SHORT
0
0
0
< COIL >
7-10
MA-316
Ref. No.
L750
L755
Part No.
Description
Remarks
1-414-930-21 INDUCTOR
1-414-940-21 INDUCTOR
Ref. No.
2.2uH
100uH
< PHOTO INTERRUPTER >
PH100
PH101
8-749-013-23 PHOTO INTERRUPTER GP3S120
8-749-013-23 PHOTO INTERRUPTER GP3S120
< IC LINK >
! PS130
! PS131
! PS331
! PS533
1-533-586-31
1-533-586-31
1-533-586-31
1-533-586-31
LINK, IC 315mA
LINK, IC 315mA
LINK, IC 315mA
LINK, IC 315mA
< TRANSISTOR >
Q100
Q101
Q102
Q141
Q201
8-729-043-84
8-729-043-84
8-729-281-53
8-729-424-08
8-729-422-27
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
PT380F3
PT380F3
2SC1815-GR
UN2111
2SD601A-Q
Q202
Q208
Q209
Q210
Q211
8-729-422-27
8-729-422-27
8-729-216-22
8-729-422-27
8-729-422-27
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SD601A-Q
2SD601A-Q
2SA1162
2SD601A-Q
2SD601A-Q
Q301
Q501
Q502
Q510
Q533
8-729-281-53
8-729-424-08
8-729-421-19
8-729-216-22
8-729-804-41
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC1815-GR
UN2111
UN2213
2SA1162
2SB1122-S
Q534
Q540
Q611
Q612
Q613
8-729-421-19
8-729-216-22
8-729-804-41
8-729-421-19
8-729-422-27
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
UN2213
2SA1162
2SB1122-S
UN2213
2SD601A-Q
Q660
Q661
Q662
Q663
Q664
8-729-421-19
8-729-422-27
8-729-216-22
8-729-216-22
8-729-216-22
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
UN2213 (B)
2SD601A-Q (B)
2SA1162
2SA1162
2SA1162
Q703
Q751
Q752
Q800
Q801
8-729-421-19
8-729-421-19
8-729-216-22
8-729-216-22
8-729-422-27
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
UN2213
UN2213
2SA1162
2SA1162
2SD601A-Q
Q802
Q803
Q804
Q820
Q821
8-729-422-27
8-729-422-27
8-729-421-19
8-729-422-27
8-729-422-27
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SD601A-Q
2SD601A-Q
UN2213
2SD601A-Q
2SD601A-Q
Q850
8-729-216-22 TRANSISTOR 2SA1162
< RESISTOR >
R100
R101
R102
R103
R104
1-249-400-11
1-249-400-11
1-216-057-00
1-216-085-00
1-216-085-00
CARBON
CARBON
METAL CHIP
METAL CHIP
METAL CHIP
39
39
2.2K
33K
33K
5%
5%
5%
5%
5%
1/4W F
1/4W F
1/10W
1/10W
1/10W
Part No.
Description
R105
R106
R107
R109
R110
1-249-413-11
1-216-089-91
1-216-089-91
1-216-057-00
1-216-057-00
CARBON
RES,CHIP
RES,CHIP
METAL CHIP
METAL CHIP
470
47K
47K
2.2K
2.2K
5%
5%
5%
5%
5%
1/4W F
1/10W
1/10W
1/10W
1/10W
R111
R112
R113
R114
R115
1-216-103-00
1-216-689-11
1-208-806-11
1-208-806-11
1-216-089-91
METAL CHIP
METAL CHIP
RES,CHIP
RES,CHIP
RES,CHIP
180K
39K
10K
10K
47K
5%
0.5%
0.50%
0.50%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R116
R117
R118
R130
R131
1-216-089-91
1-216-089-91
1-216-089-91
1-216-085-00
1-216-085-00
RES,CHIP
RES,CHIP
RES,CHIP
METAL CHIP
METAL CHIP
47K
47K
47K
33K
33K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R132
R133
R134
R145
R147
1-216-065-91
1-216-073-00
1-216-089-91
1-216-105-91
1-208-830-11
RES,CHIP
METAL CHIP
RES,CHIP
RES,CHIP
RES,CHIP
4.7K
10K
47K
220K
100K
5%
5%
5%
5%
0.50%
1/10W
1/10W
1/10W
1/10W
1/10W
R148
R149
R151
R152
R153
1-208-830-11
1-208-830-11
1-208-830-11
1-216-111-00
1-216-057-00
RES,CHIP
RES,CHIP
RES,CHIP
METAL CHIP
METAL CHIP
100K
100K
100K
390K
2.2K
0.50%
0.50%
0.50%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R155
R160
R161
R162
R163
1-216-065-91
1-216-073-00
1-216-073-00
1-216-089-91
1-249-429-11
RES,CHIP
METAL CHIP
METAL CHIP
RES,CHIP
CARBON
4.7K
10K
10K
47K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/4W
R164
R165
R166
R167
R168
1-249-437-11
1-216-041-00
1-216-041-00
1-249-417-11
1-247-807-31
CARBON
METAL CHIP
METAL CHIP
CARBON
CARBON
47K
470
470
1K
100
5%
5%
5%
5%
5%
1/4W
1/10W
1/10W
1/4W F
1/4W
R169
R170
R171
R172
R173
1-247-807-31
1-247-807-31
1-247-807-31
1-249-429-11
1-249-429-11
CARBON
CARBON
CARBON
CARBON
CARBON
100
100
100
10K
10K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R174
R175
R176
R177
R178
1-216-041-00
1-216-049-91
1-249-429-11
1-216-057-00
1-216-295-91
METAL CHIP
RES,CHIP
CARBON
METAL CHIP
SHORT
0
470
1K
10K
2.2K
5%
5%
5%
5%
1/10W
1/10W
1/4W
1/10W
R179
R180
R181
R183
R184
1-249-429-11
1-216-089-91
1-216-097-91
1-249-413-11
1-249-413-11
CARBON
RES,CHIP
RES,CHIP
CARBON
CARBON
10K
47K
100K
470
470
5%
5%
5%
5%
5%
1/4W
1/10W
1/10W
1/4W F
1/4W F
R201
R202
R203
R204
R205
1-216-041-00
1-216-067-00
1-249-413-11
1-216-047-91
1-216-037-00
METAL CHIP
METAL CHIP
CARBON
RES,CHIP
METAL CHIP
470
5.6K
470
820
330
5%
5%
5%
5%
5%
1/10W
1/10W
1/4W F
1/10W
1/10W
Note :
7-11
Remarks
The components identified by mark ! or dotted
line with mark ! are critical for safety.
Replace only with part number specified.
MA-316
Ref. No.
Part No.
Description
Part No.
Description
R206
R207
R208
R209
R210
1-216-037-00
1-216-073-00
1-216-059-00
1-216-041-00
1-216-025-91
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
RES,CHIP
330
10K
2.7K
470
100
5%
5%
5%
5%
5%
Remarks
1/10W
1/10W
1/10W
1/10W
1/10W
Ref. No.
R399
R500
R501
R502
R503
1-216-049-91
1-216-041-00
1-216-041-00
1-216-025-91
1-216-025-91
RES,CHIP
METAL CHIP
METAL CHIP
RES,CHIP
RES,CHIP
1K
470
470
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R218
R219
R221
R222
R223
1-216-065-91
1-216-053-00
1-216-057-00
1-216-051-00
1-216-017-91
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
RES,CHIP
4.7K
1.5K
2.2K
1.2K
47
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R504
R505
R510
R511
R512
1-216-069-00
1-216-069-00
1-249-408-11
1-249-407-11
1-216-021-00
METAL CHIP
METAL CHIP
CARBON
CARBON
METAL CHIP
6.8K
6.8K
180
150
68
5%
5%
5%
5%
5%
1/10W
1/10W
1/4W F
1/4W F
1/10W
R224
R225
R226
R227
R228
1-216-017-91
1-216-017-91
1-216-025-91
1-216-025-91
1-216-057-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
METAL CHIP
47
47
100
100
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R514
R515
R516
R517
R533
1-216-037-00
1-216-049-91
1-216-065-91
1-216-022-00
1-216-049-91
METAL CHIP
RES,CHIP
RES,CHIP
METAL CHIP
RES,CHIP
330
1K
4.7K
75
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R229
R230
R231
R232
R233
1-216-051-00
1-216-045-00
1-216-071-00
1-216-049-91
1-216-055-00
METAL CHIP
METAL CHIP
METAL CHIP
RES,CHIP
METAL CHIP
1.2K
680
8.2K
1K
1.8K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R534
R540
R541
R542
R545
1-216-049-91
1-216-025-91
1-216-053-00
1-216-053-00
1-216-085-00
RES,CHIP
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
100
1.5K
1.5K
33K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R234
R235
R236
R239
R240
1-216-089-91
1-216-049-91
1-216-049-91
1-216-057-00
1-216-049-91
RES,CHIP
RES,CHIP
RES,CHIP
METAL CHIP
RES,CHIP
47K
1K
1K
2.2K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R546
R547
R548
R549
R570
1-216-089-91
1-216-049-91
1-216-022-00
1-247-804-11
1-249-413-11
RES,CHIP
RES,CHIP
METAL CHIP
CARBON
CARBON
47K
1K
75
75
470
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/4W
1/4W F
R243
R248
R301
R302
R306
1-216-061-00
1-216-295-91
1-249-439-11
1-216-067-00
1-216-073-00
METAL CHIP
SHORT
0
CARBON
METAL CHIP
METAL CHIP
3.3K
5%
1/10W
68K
5.6K
10K
5%
5%
5%
1/4W
1/10W
1/10W
R571
R572
R573
R574
R575
1-249-413-11
1-216-025-91
1-216-025-91
1-216-097-91
1-216-097-91
CARBON
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
470
100
100
100K
100K
5%
5%
5%
5%
5%
1/4W F
1/10W
1/10W
1/10W
1/10W
R307
R309
R310
R311
R312
1-216-061-00
1-216-067-00
1-216-129-00
1-216-051-00
1-216-079-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
3.3K
5.6K
2.2M
1.2K
18K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R620
R621
R622
R623
R624
1-216-049-91
1-216-049-91
1-216-073-00
1-249-429-11
1-216-079-00
RES,CHIP
RES,CHIP
METAL CHIP
CARBON
METAL CHIP
1K
1K
10K
10K
18K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/4W
1/10W
R313
R314
R315
R316
R318
1-216-109-00
1-216-035-00
1-216-069-00
1-216-073-00
1-216-075-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
330K
270
6.8K
10K
12K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R660
1-216-073-00 METAL CHIP
10K
5%
R661
1-216-073-00 METAL CHIP
10K
5%
R320
R360
R361
R368
R370
1-216-047-91
1-216-081-00
1-216-081-00
1-216-133-00
1-216-065-91
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
RES,CHIP
820
22K
22K
3.3M
4.7K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R662
R663
R664
1-216-059-00 METAL CHIP
1-216-053-00 METAL CHIP
1-216-081-00 METAL CHIP
2.7K
1.5K
22K
5%
5%
5%
110W
(B)
1/10W
(B)
1/10W
1/10W
1/10W
R371
R372
R378
R380
R381
1-208-820-11
1-216-065-91
1-216-083-00
1-216-295-91
1-216-295-91
RES,CHIP
RES,CHIP
METAL CHIP
SHORT
0
SHORT
0
39K
4.7K
27K
0.50% 1/10W
5%
1/10W
5%
1/10W
R665
R666
R667
R668
R669
1-216-041-00
1-216-041-00
1-216-081-00
1-216-073-00
1-216-033-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
470
470
22K
10K
220
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R382
R383
R384
R385
R389
1-216-079-00
1-216-079-00
1-216-091-00
1-216-091-00
1-216-073-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
18K
18K
56K
56K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R670
R671
R672
R673
R674
1-216-041-00
1-249-407-11
1-216-073-00
1-216-073-00
1-216-073-00
METAL CHIP
CARBON
METAL CHIP
METAL CHIP
METAL CHIP
470
150
10K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/4W F
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
RES,CHIP
18K
18K
18K
18K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
RES,CHIP
RES,CHIP
METAL CHIP
RES,CHIP
SHORT
0
5%
5%
5%
5%
1-216-079-00
1-216-079-00
1-216-079-00
1-216-079-00
1-216-049-91
1-216-063-91
1-216-043-91
1-216-101-00
1-216-049-91
1-216-295-91
3.9K
560
150K
1K
R390
R391
R392
R393
R394
R675
R676
R677
R678
R702
R709
1-216-081-00 METAL CHIP
22K
5%
R709
1-216-105-91 RES,CHIP
220K
R711
1-212-893-00 FUSIBLE
330
7-12
Remarks
1/10W
(NP,VC1,VC2)
5%
1/10W
(B)
5%
1/4W F
MA-316
Ref. No.
Part No.
Description
R713
R714
R715
R716
R717
1-216-025-91
1-216-113-00
1-216-049-91
1-216-049-91
1-216-037-00
RES,CHIP
METAL CHIP
RES,CHIP
RES,CHIP
METAL CHIP
R730
R731
Remarks
Ref. No.
Part No.
RP-231
Description
Remarks
< TUNER >
100
470K
1K
1K
330
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
1-216-041-00 METAL CHIP
1-216-041-00 METAL CHIP
470
470
5%
5%
R732
R733
1-216-041-00 METAL CHIP
1-216-041-00 METAL CHIP
470
470
5%
5%
1/10W
1/10W
(B)
1/10W
1/10W
(B)
R754
R755
R756
R757
R800
1-216-025-91
1-216-025-91
1-216-073-00
1-216-049-91
1-216-101-00
RES,CHIP
RES,CHIP
METAL CHIP
RES,CHIP
METAL CHIP
100
100
10K
1K
150K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R801
R802
R803
R804
R805
1-216-073-00
1-216-073-00
1-216-081-00
1-216-073-00
1-216-073-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
22K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R806
R807
R813
R820
R821
1-216-073-00
1-216-085-00
1-216-073-00
1-216-073-00
1-216-073-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
33K
10K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R823
R825
R826
R827
R828
1-216-081-00
1-216-081-00
1-216-065-91
1-216-065-91
1-216-065-91
METAL CHIP
METAL CHIP
RES,CHIP
RES,CHIP
RES,CHIP
22K
22K
4.7K
4.7K
4.7K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R829
R830
R831
R832
R833
1-216-081-00
1-216-081-00
1-216-065-91
1-216-037-00
1-216-065-91
METAL CHIP
METAL CHIP
RES,CHIP
METAL CHIP
RES,CHIP
22K
22K
4.7K
330
4.7K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R834
R850
R851
R852
R853
1-216-065-91
1-247-807-31
1-216-079-00
1-216-083-00
1-216-049-91
RES,CHIP
CARBON
METAL CHIP
METAL CHIP
RES,CHIP
4.7K
100
18K
27K
1K
5%
5%
5%
5%
5%
1/10W
1/4W
1/10W
1/10W
1/10W
R856
R857
R858
R859
R860
1-216-097-91
1-216-069-00
1-216-069-00
1-216-123-11
1-216-123-11
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
6.8K
6.8K
1.2M
1.2M
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R861
R862
1-216-117-00 METAL CHIP
1-216-057-00 METAL CHIP
680K
2.2K
5%
5%
1/10W
1/10W
TU701
TU702
TU702
8-598-402-00 FSS TUNER BTF-WC411 (NP)
1-693-362-11 TUNER, (IF) SOLID TYPE (B)
1-693-368-11 TUNER, (IF) SOLID TYPE (VC1,VC2)
< VIBRATOR >
X160
1-760-494-11 VIBRATOR, CRYSTAL 16MHz
X201
1-579-608-11 VIBRATOR, CRYSTAL 4.433619MHz
X660
1-577-289-11 VIBRATOR, CRYSTAL 17.734475MHz
X661
1-577-165-11 VIBRATOR, CERAMIC
************************************************************
A-6791-531-A RP-231 BOARD, COMPLETE
**********************
(Ref.No.:1,000 series)
*
< CAPACITOR >
< MODULATOR >
RFU750 1-475-058-11 MODULATOR, RF (RFU-2110) (B)
RFU750 1-475-059-11 MODULATOR, RF (RFU-2101) (NP,VC1,VC2)
< SWITCH >
S100
S101
S160
1-771-155-11 SWITCH, ROTARY (ROTARY ENCODER)
1-762-108-11 SWITCH, PUSH (1 KEY)
(CASSETTE IN/REC PROOF)
1-571-588-31 SWITCH, SLIDE (NTSC PB)
7-13
C141
C142
C143
C144
C145
1-163-009-11
1-126-960-11
1-126-967-11
1-163-031-11
1-163-018-00
CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
0.001uF
1uF
47uF
0.01uF
0.0056uF
10%
20%
20%
5%
50V
50V
16V
50V
50V
C146
C147
C260
C261
C264
1-126-933-11
1-126-960-11
1-163-229-11
1-163-229-11
1-163-037-11
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100uF
1uF
12PF
12PF
0.022uF
20%
20%
5%
5%
10%
16V
50V
50V
50V
25V
C265
C266
C267
C268
C269
1-163-037-11
1-163-031-11
1-163-037-11
1-163-243-11
1-163-243-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.022uF
0.01uF
0.022uF
47PF
47PF
10%
10%
5%
5%
25V
50V
25V
50V
50V
C270
C271
C272
C273
C274
1-163-037-11
1-163-037-11
1-163-243-11
1-163-243-11
1-163-037-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.022uF
0.022uF
47PF
47PF
0.022uF
10%
10%
5%
5%
10%
25V
25V
50V
50V
25V
C275
C276
C277
C278
C279
1-109-982-11
1-163-037-11
1-163-037-11
1-163-037-11
1-163-037-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
1uF
0.022uF
0.022uF
0.022uF
0.022uF
10%
10%
10%
10%
10%
10V
25V
25V
25V
25V
C280
C282
C283
C284
C285
1-124-584-00
1-164-232-11
1-163-038-91
1-163-038-91
1-109-982-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100uF
0.01uF
0.1uF
0.1uF
1uF
20%
10V
50V
25V
25V
10V
C286
C287
C288
C289
C298
1-128-057-11
1-163-239-11
1-163-239-11
1-163-038-91
1-163-031-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
330uF
33PF
33PF
0.1uF
0.01uF
20%
5%
5%
6.3V
50V
50V
25V
50V
C321
C322
C323
C324
C331
1-126-967-11
1-164-232-11
1-164-232-11
1-137-462-11
1-126-933-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
FILM
ELECT
47uF
0.01uF
0.01uF
0.018uF
100uF
20%
5%
20%
16V
50V
50V
100V
16V
C332
C334
C335
C340
C341
1-164-232-11
1-163-011-11
1-137-397-11
1-163-031-11
1-124-584-00
CERAMIC CHIP
CERAMIC CHIP
FILM
CERAMIC CHIP
ELECT
0.01uF
0.0015uF 10%
0.047uF 5%
0.01uF
100uF
20%
50V
50V
100V
50V
10V
10%
RP-231
Ref. No.
SE-69
Part No.
Description
C342
C346
C350
C352
C353
1-164-004-11
1-164-232-11
1-164-004-11
1-163-009-11
1-163-038-91
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.01uF
0.1uF
0.001uF
0.1uF
10%
Remarks
Part No.
Description
25V
50V
25V
50V
25V
R264
R265
R266
R267
R268
1-216-295-91
1-216-295-91
1-216-053-00
1-216-071-00
1-216-081-00
SHORT
0
SHORT
0
METAL CHIP
METAL CHIP
METAL CHIP
1.5K
8.2K
22K
5%
5%
5%
1/10W
1/10W
1/10W
C357
C358
C359
1-163-009-11 CERAMIC CHIP
1-163-038-91 CERAMIC CHIP
1-163-031-11 CERAMIC CHIP
0.001uF
0.1uF
0.01uF
10%
50V
25V
50V
< CONNECTOR >
R269
R270
R271
R272
R273
1-216-059-00
1-216-081-00
1-216-049-91
1-216-081-00
1-216-081-00
METAL CHIP
METAL CHIP
RES,CHIP
METAL CHIP
METAL CHIP
2.7K
22K
1K
22K
22K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
CONNECTOR, FFC/FPC 13P
PIN, CONNECTOR 5P
CONNECTOR, BOARD TO BOARD 15P
CONNECTOR, BOARD TO BOARD 17P
PIN, CONNECTOR 2P
R274
R275
R276
R317
R321
1-216-073-00
1-216-073-00
1-216-049-91
1-216-079-00
1-216-017-91
METAL CHIP
METAL CHIP
RES,CHIP
METAL CHIP
RES,CHIP
10K
10K
1K
18K
47
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R322
R323
R324
R332
R333
1-216-067-00
1-249-381-11
1-249-408-11
1-216-083-00
1-249-394-11
METAL CHIP
CARBON
CARBON
METAL CHIP
CARBON
5.6K
1
180
27K
12
5%
5%
5%
5%
5%
1/10W
1/4W F
1/4W F
1/10W
1/4W F
R335
R336
R337
R344
R346
1-216-073-00
1-216-164-00
1-216-164-00
1-216-053-00
1-216-065-91
METAL CHIP
RES,CHIP
RES,CHIP
METAL CHIP
RES,CHIP
10K
39
39
1.5K
4.7K
5%
5%
5%
5%
5%
1/10W
1/8W
1/8W
1/10W
1/10W
R347
R348
1-216-065-91 RES,CHIP
1-216-033-00 METAL CHIP
4.7K
220
5%
5%
1/10W
1/10W
CN260
* CN261
CN271
CN272
CN301
1-784-492-11
1-564-030-00
1-573-829-11
1-766-720-11
1-506-481-11
* CN302
* CN341
1-568-944-11 PIN, CONNECTOR 6P
1-564-027-00 PIN, CONNECTOR 2P
10%
10%
Ref. No.
< IC >
IC140
IC260
IC301
IC340
8-759-438-83
8-759-352-17
8-759-089-84
8-759-486-92
IC
IC
IC
IC
BA6305F-E2
HA118195NT
BA7755AF-T1
LA7256
< JUMPER RESISTOR >
JR260
1-216-295-91 SHORT
0
Remarks
< JUMPER RESISTOR >
< TRANSFORMER >
JS350
1-216-295-91 SHORT
0
T321
1-431-100-11 TRANSFORMER, BIAS OSCILLATION
T331
1-423-415-11 TRANSFORMER, BIAS OSCILLATION
************************************************************
< COIL >
L140
L262
L263
L321
L322
1-414-940-21
1-414-940-21
1-414-940-21
1-414-940-21
1-414-940-21
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
100uH
100uH
100uH
100uH
100uH
L331
L341
1-410-687-11 INDUCTOR
1-414-940-21 INDUCTOR
1.2mH
100uH
A-6791-537-A SE-69 BOARD, COMPLETE (B)
*************************
(Ref.No.:2,000 series)
*
< CAPACITOR >
< IC LINK >
PS331
1-533-586-31 LINK, IC 315mA
< TRANSISTOR >
Q260
Q321
Q331
Q332
8-729-422-27
8-729-802-91
8-729-012-31
8-729-900-51
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SD601A-Q
2SD879
2SC4040-TL2-Q
DTA114TK
< RESISTOR >
R140
R141
R142
R143
R144
1-216-117-00
1-216-037-00
1-216-049-91
1-216-065-91
1-216-043-91
METAL CHIP
METAL CHIP
RES,CHIP
RES,CHIP
RES,CHIP
680K
330
1K
4.7K
560
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R150
R260
R261
R262
R263
1-216-065-91
1-216-043-91
1-216-043-91
1-216-295-91
1-216-295-91
RES,CHIP
RES,CHIP
RES,CHIP
SHORT
SHORT
4.7K
560
560
5%
5%
5%
1/10W
1/10W
1/10W
0
0
7-14
C970
C971
C972
C973
C974
1-163-259-91
1-124-257-00
1-163-017-00
1-164-232-11
1-109-982-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
220PF
2.2uF
0.0047uF
0.01uF
1uF
5%
20%
5%
C975
C976
C977
C978
C979
1-163-037-11
1-163-259-91
1-164-232-11
1-163-017-00
1-163-121-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.022uF
220PF
0.01uF
0.0047uF
150PF
10%
5%
C980
C981
C982
C983
C984
1-107-725-11
1-164-232-11
1-163-007-11
1-163-009-11
1-164-232-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.01uF
680PF
0.001uF
0.01uF
10%
C985
C986
C987
C988
C991
1-163-251-11
1-126-157-11
1-107-823-11
1-163-251-11
1-107-725-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100PF
10uF
0.47uF
100PF
0.1uF
10%
5%
5%
10%
10%
5%
20%
10%
5%
10%
50V
50V
50V
50V
10V
25V
50V
50V
50V
50V
16V
50V
50V
50V
50V
50V
16V
16V
50V
16V
SE-69
Ref. No.
C992
C993
C994
C995
C996
Part No.
Description
1-164-232-11
1-163-031-11
1-163-031-11
1-126-157-11
1-163-227-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
0.01uF
0.01uF
0.01uF
10uF
10PF
20%
0.5PF
Part No.
POWER BLOCK
Remarks
Ref. No.
50V
50V
50V
16V
50V
R998
1-216-073-00 METAL CHIP
10K
5%
1/10W
R999
1-216-295-91 SHORT
0
************************************************************
Description
Remarks
1-468-273-11 POWER BLOCK SR826
*****************
!
< CONNECTOR >
CN970
(Ref.No.: 9,000 Series)
1-573-825-11 CONNECTOR, BOARD TO BOARD 11P
< CAPACITOR >
< IC >
IC970
JR970
JR971
JR972
JR973
JR974
< JUMPER RESISTOR >
C151
C153
C154
C201
C202
9-980-236-01
1-126-967-11
1-126-960-11
1-126-934-11
1-126-925-11
ELECT
ELECT
ELECT
ELECT
ELECT
47uF
47uF
1uF
220uF
470uF
400V
50V
50V
16V
10V
SHORT
SHORT
SHORT
SHORT
SHORT
C203
C204
C205
C206
C207
1-126-934-11
1-126-933-11
1-126-965-11
1-126-947-11
1-126-965-11
ELECT
ELECT
ELECT
ELECT
ELECT
220uF
100uF
22uF
47uF
22uF
16V
16V
50V
35V
50V
C208
C251
C252
C253
C254
1-126-925-11
1-126-967-11
1-126-183-11
1-126-927-11
1-126-967-11
ELECT
ELECT
ELECT
ELECT
ELECT
470uF
47uF
1000uF
2200uF
47uF
10V
50V
16V
10V
50V
C255
1-126-925-11 ELECT
470uF
10V
8-759-438-17 IC LA7337
1-216-296-91
1-216-296-91
1-216-296-91
1-216-295-91
1-216-295-91
0
0
0
0
0
< COIL >
L970
L971
L972
L973
L975
1-414-933-11
1-414-945-11
1-414-938-21
1-414-938-21
1-414-934-21
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
6.8uH
27uH
47uH
47uH
10uH
< TRANSISTOR >
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
< DIODE >
Q970
Q972
Q973
Q974
Q975
8-729-216-22
8-729-424-08
8-729-422-27
8-729-422-27
8-729-424-08
2SA1162
UN2111
2SD601A-Q
2SD601A-Q
UN2111
Q976
8-729-421-19 TRANSISTOR UN2213
< RESISTOR >
R969
R970
R971
R972
R973
1-216-069-00
1-216-085-00
1-216-085-00
1-216-093-00
1-216-689-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
6.8K
33K
33K
68K
39K
5%
5%
5%
5%
0.5%
1/10W
1/10W
1/10W
1/10W
1/10W
R974
R975
R976
R977
R978
1-216-081-00
1-216-295-91
1-216-059-00
1-216-089-91
1-216-071-00
METAL CHIP
SHORT
0
METAL CHIP
RES,CHIP
METAL CHIP
22K
5%
1/10W
2.7K
47K
8.2K
5%
5%
5%
1/10W
1/10W
1/10W
R979
R980
R981
R982
R983
1-216-073-00
1-216-097-91
1-216-083-00
1-216-089-91
1-216-065-91
METAL CHIP
RES,CHIP
METAL CHIP
RES,CHIP
RES,CHIP
10K
100K
27K
47K
4.7K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R985
R986
R988
R989
R990
1-216-041-00
1-216-089-91
1-216-083-00
1-216-049-91
1-216-295-91
METAL CHIP
RES,CHIP
METAL CHIP
RES,CHIP
SHORT
0
470
47K
27K
1K
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
R993
R994
R995
R996
R997
1-216-071-00
1-216-689-11
1-216-073-00
1-216-689-11
1-216-073-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
8.2K
39K
10K
39K
10K
5%
0.5%
5%
0.5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
D151
D153
D154
D155
D203
8-719-043-74
8-719-911-19
8-719-043-74
9-900-535-01
8-719-109-85
DIODE
DIODE
DIODE
DIODE
DIODE
AK04
1SS119
AK04
AU02Z
RD5.1ES
D204
D205
D251
D252
D253
8-719-911-19
8-719-911-19
9-900-535-01
8-719-510-73
8-719-027-20
DIODE
DIODE
DIODE
DIODE
DIODE
1SS119
1SS119
AU02Z
S3L20U
D3S4M
D254
D255
9-900-535-01 DIODE
9-900-535-01 DIODE
AU02Z
AU02Z
< FUSE >
! F101
1-532-388-31 FUSE
T2A, 250V
< IC >
IC151
IC201
9-980-235-01 IC
8-759-438-18 IC
AN8028
PQ12RD08
< PHOTOCOUPLER >
! PC151
8-749-924-80 PHOTOCOUPLER PS2561
< IC LINK >
! PS201
! PS202
! PS251
1-533-592-21 LINK, IC
1-533-593-21 LINK, IC
1-533-588-11 FUSE
Note :
7-15
1.6A
2A
0.5A
The components identified by mark ! or dotted
line with mark ! are critical for safety.
Replace only with part number specified.
POWER BLOCK
Ref. No.
Part No.
Description
Remarks
Ref. No.
Part No.
Description
< TRANSISTOR >
Q201
Q205
Q206
Q208
Q211
8-729-113-32
8-729-019-01
8-729-119-78
8-729-177-32
8-729-422-72
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SB733
2SD2394
2SC2785
2SD773
UN4211
1-696-593-11 CORD, CONNECTION (PAL) (FOR RF) 1.5m
1-696-861-11 CORD, CONNECTION (FOR AUDIO) 1.5m
1-782-213-11 CABLE, CONNECTION (21P) (FOR EURO-AV)
1.5m
3-862-065-11 MANUAL, INSTRUCTION (GERMAN)
(NP,VC1,VC2)
3-862-065-21 MANUAL, INSTRUCTION (FRENCH) (NP,VC2)
< RESISTOR >
R253
9-980-233-01 FUSIBLE
0.47
1/4W
3-862-065-31
3-862-065-41
3-862-065-51
3-862-065-61
3-862-065-71
MISCELLANEOUS
*************
!9
11
12
14
! 54
56
721
769
769
M902
Remarks
ACCESSORIES & PACKING MATERIALS
*******************************
1-782-012-11
1-762-844-31
1-783-169-11
1-783-167-11
1-468-273-11
CORD, POWER
SWITCH, ROTARY
CABLE, FLAT (FFD-2)
CABLE, FLAT (FFM-18)
POWER BLOCK
1-779-725-11
A-6759-620-A
1-759-373-11
1-759-557-11
1-698-971-11
CONNECTOR, BOARD TO BOARD 5P
HEAD BLOCK ASSY, ACE (TDK)
DRUM ASSY DZH-86A-R (M901)(NP,VC1,VC2)
DRUM ASSY DZH-98A-R (M901)(B)
MOTOR, DC (CAPSTAN)
MANUAL, INSTRUCTION (ITALIAN) (VC2)
MANUAL, INSTRUCTION (DUTCH) (NP,VC2)
MANUAL, INSTRUCTION (SPANISH) (NP)
MANUAL, INSTRUCTION (PORTUGUESE) (NP)
MANUAL, INSTRUCTION (SWEDISH) (NP)
3-862-065-81
3-862-065-91
3-862-066-11
3-862-067-11
MANUAL, INSTRUCTION (DANISH) (NP)
MANUAL, INSTRUCTION (FINNISH) (NP)
MANUAL, INSTRUCTION (FRENCH) (B)
MANUAL, INSTRUCTION (GERMAN)
(NP,VC1,VC2)
3-862-067-21 MANUAL, INSTRUCTION (FRENCH) (NP,VC2)
3-862-067-31
3-862-067-41
3-862-067-51
3-862-067-61
3-862-067-71
M903
X-3947-577-1 MOTOR ASSY,CAM
************************************************************
MANUAL, INSTRUCTION (ITALIAN) (VC2)
MANUAL, INSTRUCTION (DUTCH) (NP,VC2)
MANUAL, INSTRUCTION (SPANISH) (NP)
MANUAL, INSTRUCTION (PORTUGUESE) (NP)
MANUAL, INSTRUCTION (SWEDISH) (NP)
3-862-067-81 MANUAL, INSTRUCTION (DANISH) (NP)
3-862-067-91 MANUAL, INSTRUCTION (FINNISH) (NP)
3-862-068-11 MANUAL, INSTRUCTION (FRENCH) (B)
*
3-988-123-01 INDIVIDUAL CARTON (NP,VC1,VC2)
*
3-988-123-11 INDIVIDUAL CARTON (B)
************************************************************
*************
HARDWARE LIST
*************
#1
#2
#701
#702
#703
7-685-648-79
7-685-646-79
7-685-646-79
7-682-547-04
7-685-133-19
Note :
7-16E
SCREW +BVTP 3X12 TYPE2
SCREW +BVTP 3X8 TYPE2 IT-3
SCREW +BVTP 3X8 TYPE2 IT-3
SCREW +P 3X6
SCREW (DIA)(IT3B)
The components identified by mark ! or dotted
line with mark ! are critical for safety.
Replace only with part number specified.
SLV-E830B/E830NP/E830VC1/E830VC2
Sony Corporation
9-921-673-11
Home A&V Products Company
— 118 —
98B1637-1
Printed in Japan ©1998.2
Published by General Engineering Dept.
(Osaki East)