Download sony chassis FE-1-32015-05-09 01:345.7 MB - Wiki Karat
Transcript
SELF-DIAGNOSTIC FUNCTION SERVICE MANUAL MODEL KV-25K5K COMMANDER RM-883 DEST OIRT CHASSIS NO. SCC-Q03M-A FE-1 MODEL COMMANDER KV-29K5K RM-883 CHASSIS DEST OIRT CHASSIS NO. SCC-Q03N-A / MENU PROGR RM-883 TRINITRON ® COLOR TV ® MICROFILM 1 [TELEVISION SYSTEM] - B/G/H, D/K [COLOUR SYSTEM] 21-pin Euro connector. inputs for Audio and Video signals. inputs for S Video. outputs for Audio and Video signals (selectable). Phono Jack Outputs for Audio Signals [FRONT] PAL SECAM NTSC 3.58,4.43 (Video in) Video input - phono jack Audio inputs - phono jacks S Video input 4 pin DIN Headphone jacks : stereo minijack [CHANNEL COVERAGE] PAL B/G/H VHF : E2-E12, A-H2 UHF : E21-E69 CABLE TV : S1-S5, S1-S20 ITALIA VHF : A-H2 (C) UHF : 21-69 D/K VHF : R01-R12 UHF : R21-R69 Sound output 2 x 20W (Music Power) Power requirements 220 - 240V Power Consumption KV-25K5 KV-29K5 97W 108W Dimensions KV-25K5 KV-29K5 Approx 612x515x485mm Approx 679x581x526mm Weight KV-25K5 KV-29K5 Approx 37kg Approx 49.5kg [STEREO SYSTEM] GERMAN/NICAM STEREO [PICTURE TUBE] KV-25K5 KV-29K5 Super Trinitron Approx. 63cm (25 inches) (Approx. 59cm picture measured diagonally) 110 degree deflection Super Trinitron Approx. 72cm (29 inches) (Approx. 68cm picture measured diagonally) 110 degree deflection Supplied accessories Other features [RM-883] Remote control system Power requirements Input/Output Terminals [REAR] - Dimensions Weight 21-pin Euro connector (CENELEC standard). Inputs for Audio and Video signals. Inputs for RGB. Outputs of TV Video and Audio signals. RM-883 Remote Commander (1) IEC designated R6 battery (2) FASTEXT, TOPTEXT, NICAM infrared control 1.5V dc 2 batteries IEC designation R6 (size AA) Approx 65x225x21mm (w/h/d) Approx 157g (Not including batteries) Design and specifications are subject to change without notice. 2 Model Name KV-25K5K KV-29K5K Pal Comb OFF OFF Velocity Modulation OFF ON DF & DQP OFF ON Woofer Box OFF OFF Scart 1 ON ON Scart 2 ON ON Front in ON ON Scart 4 OFF OFF Projector OFF OFF AKB in 16:9 mode ON ON Norm B/G/H ON ON Norm I OFF OFF Norm D/K ON ON Norm AUS OFF OFF Norm L OFF OFF Norm SAT OFF OFF Norm M OFF OFF Teletext ON ON Nicam Stereo ON ON OIRT OIRT Item Language Preset The ASA T flexible mains lead is supplied connected to a B.S. 1363 fused plug having a fuse of 5 AMP capacity. Should the fuse need to be replaced, use a 5 AMP FUSE approved by ASTA to BS 1362, ie one that carries the the mark. IF THE PLUG SUPPLIED WITH THIS APPLIANCE IS NOT SUITABLE FOR THE OUTLET SOCKETS IN YOUR HOME, IT SHOULD BE CUT OFF AND AN APPROPRIATE PLUG FITTED. THE PLUG SEVERED FROM THE MAINS LEAD MUST BE DESTROYED AS A PLUG WITH BARED WIRES IS DANGEROUS IF ENGAGED IN A LIVE OUTLET SOCKET. When an alternative type of plug is used it should be fitted with a 5 AMP FUSE, otherwise the circuit should be protected by a 5 AMP FUSE at the How to replace the fuse. distribution board. Open the fuse compartment with a screwdriver blade and replace the fuse. FUSE 3 21 pin connector ( , 21 20 19 18 17 2/ 2) Pin No 1 2 4 1 2 Audio output B (right) Standard level : 0.5V rms Output impedence : More than 10kohm* 3 Audio output A (left) Standard level : 0.5V rms Output impedence : Less than 1kohm* 4 Ground (audio) 5 Ground (blue) 6 Audio input A (left) Standard level : 0.5V rms Output impedence : More than 10kohm* 7 Blue input 0.7 +/- 3dB, 75 ohms positive 8 Function select (AV control) High state (9.5-12V) : Part mode Low state (0-2V) : TV mode Input impedence : More than 10K ohms Input capacitance : Less than 2nF 9 Ground (green) 10 Open 11 Green 12 Open 13 Ground (red) Green signal : 0.7 +/- 3dB, 75 ohms, positive Ground (blanking) 16 _ _ Red input 0.7 +/- 3dB, 75 ohms, positive (S signal Chroma input) 0.3 +/- 3dB, 75 ohms, positive High state (1-3V) Low state (0-0.4V) Input impedence : 75 ohms 14 15 12 16 Blanking input (Ys signal) 10 17 Ground (video output) 8 18 Ground (video input) 6 19 Video output 1V +/- 3dB, 75ohms, positive sync 0.3V (-3+10dB) Video input 1V +/- 3dB, 75ohms, positive sync 0.3V (-3+10dB) Video input Y (S signal) 1V +/- 3dB, 75ohms, positive sync 0.3V (-3+10dB) _ 13 11 9 7 5 Signal level Standard level : 0.5V rms Output impedence : Less than 1kohm* 14 15 Signal Audio output B (right) 4 3 2 _ 20 1 21 Pin No 1 2 3 4 4 _ _ Common ground (plug, shield) Signal Signal level Ground Connected Not Connected (open) * at 20Hz - 20kHz Ground Y (S signal) input 1V+/- 3dB 75 ohm, positive Sync 0.3V -3/+10dB C (S signal) input 0.3V+/- 3dB 75 ohm, positive Sync TABLE OF CONTENTS Section Title Page Section 1. GENERAL Title Overview of TV buttons Using Select Mode Adjusting the Picture Adjusting the Sound Using the Sleep Timer Viewing Teletext Exchanging Programme Pos Manually Tuning the TV Fine-Tuning Channels Using Optional Equipment Troubleshooting Specifications .....................6 .....................6 .....................7 .....................7 .....................8 .....................8 .....................9 .....................9 .....................10 .....................10 .....................11 .....................11 4-1. 4-2. 4-3. Rear Cover Removal Chassis Assy Removal Service Position H1 Board Removal S1 Board Removal Picture Tube Removal Removal and Replacement of the Main - Bracket bottom plates Electrical Adjustments Test Mode 2 FE-1 Self Diagnostic Software .....................20 .....................23 .....................24 5. DIAGRAMS 5-1. 5-2. 5-3. 2. DISASSEMBLY 2-1. 2-2. 2-3. 2-4. 2-5. 2-6. 2-7. Page 4. CIRCUIT ADJUSTMENTS 5-4. 5-5. .....................12 .....................12 .....................13 .....................13 .....................13 .....................14 Block Diagram Circuit Board Location Schematic Diagrams and Printed Wiring Boards * S1 Board * A Board * VM Board * C Board * H1 Board Semiconductors IC Blocks .....................25 .....................32 .....................32 .....................34 .....................41 .....................46 .....................49 .....................51 .....................53 .....................55 6. EXPLODED VIEWS 6-1. 6-2. .....................15 Chassis Picture Tube 7. ELECTRICAL PARTS LIST .....................56 .....................57 .....................58 3. SET-UP ADJUSTMENTS 3-1. 3-2. 3-3. 3-4. Beam Landing Convergence Screen [G2] White Balance Focus .....................16 .....................17 .....................19 .....................19 CAUTION ATTENTION SHORT CIRCUIT THE ANODE OF THE PICTURE TUBE AND THE ANODE CAP TO THE METAL CHASSIS, CRT SHIELD, OR THE CARBON PAINTED ON THE CRT, AFTER REMOVAL OF THE ANODE CAP APRES AVOIR DECONNECTE LE CAP DE’LANODE, COURT-CIRCUITER L’ANODE DU TUBE CATHODIQUE ET CELUI DE L’ANODE DU CAP AU CHASSIS METALLIQUE DE L’APPAREIL, OU AU COUCHE DE CARBONE PEINTE SUR LE TUBE CATHODIQUE OU AU BLINDAGE DU TUBE CATHODIQUE. WARNING !! AN ISOLATING TRANSFORMER SHOULD BE USED DURING ANY SERVICE WORK TO AVOID POSSIBLE SHOCK HAZARD DUE TO LIVE CHASSIS. THE CHASSIS OF THIS RECEIVER IS DIRECTLY CONNECTED TO THE POWER LINE. ATTENTION !! AFIN D’EVITER TOUT RISQUE D’ELECTROCUTION PROVENANT D’UN CHÁSSIS SOUS TENTION, UN TRANSFORMATEUR D’ISOLEMENT DOIT ETRE UTILISÈ LORS DE TOUT DÈPANNAGE. LE CHÁSSIS DE CE RÈCEPTEUR EST DIRECTMENT RACCORDÈ Á L’ALIMENTATION SECTEUR. SAFETY-RELATED COMPONENT WARNING !! COMPONENTS IDENTIFIED BY SHADING AND MARKED ON THE SCHEMATIC DIAGRAMS, EXPLODED VIEWS AND IN THE PARTS LIST ARE CRITICAL FOR SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. ATTENTION AUX COMPOSANTS RELATIFS Á LA SÈCURITÈ !! LES COMPOSANTS IDENTIFIÈS PAR UNE TRAME ET PAR UNE MARQUE SUR LES SCHÈMAS DE PRINCIPE, LES VUES EXPLOSÈES ET LES LISTES DE PIECES SONT D’UNE IMPORTANCE CRITIQUE POUR LA SÈCURITÈ DU FONCTIONNEMENT, NE LES REMPLACER QUE PAR DES COMPSANTS SONY DONT LE NUMÈRO DE PIÈCE EST INDIQUÈ DANS LE PRÈSENT MANUEL OU DANS DES SUPPLÈMENTS PUBLIÈS PAR SONY. 5 SECTION 1 GENERAL The operating instructions mentioned here are partial abstracts from the Operating Manual. The page numbers of the Operating Instruction Manual remain as in the manual. Basic TV Features Additional TV Features Overview of TV Buttons Using Select Mode You can select different preset picture and sound modes. 1 / MONO g + P _ s On/Off Switch. + Press the MENU button on the remote control to display the menu on the TV screen. SELECT SELECT OFF OK OFF g _ 2 L/G/S/I R/D/D/D 2 Video Input Button. (selects input signals from VCR etc.). Auto Tune Button 2 Volume Control Buttons. With the cursor pointing at the symbol on the TV screen as shown, press the yellow button. SELECT SELECT OFF + MONO + P _ _ 2 L/G/S/I R/D/D/D 2 s Programme Up or Down Buttons. (selects TV channels). 3 Personal Mode - reverts to settings made in “Adjusting the Picture and Sound” sections of the manual Movie Mode - for films MENU Overview of Remote Control Buttons Live Mode - for live broadcast programmes PROGR 6 To Mute Sound / To Select Channels Press to select channels. Note: The mode selected in step 3 is now stored. Changing Modes Quickly Press to view programmes in 16:9 mode. Press again to return to 4:3 mode. 1 Press the button on the remote control to display the three different modes. 2 Press the mode. To Reveal On Screen Information Press to reveal all on-screen indications. Press again to cancel. To Change Screen Format PROGR To Adjust TV Volume To Select Channels Press to adjust the volume of the TV. Press to select channels. Press the MENU button to remove the menu display from the TV screen. RM-883 For double-digit programme numbers, e.g. 23, press -/-- first, then the buttons 2 and 3. MENU 4 To Temporarily Switch Off TV Press to temporarily switch off TV. Press again to switch on TV from standby mode. To save energy we recommend switching off completely when TV is not in use. NOTE: After 15 -30 minutes without a TV signal and without any button being pressed, the TV switches automatically into standby mode. Press to mute TV sound. Press again to restore the sound. Press the blue button to select the desired mode: RM-883 7 8 button again to select your desired Additional TV Features Additional TV Features Adjusting the Picture Adjusting the Sound Although the picture is adjusted at the factory, you can modify it to suit your own requirement. Although the sound is adjusted at the factory, you can modify it to suit your own requirement. 1 / 2 3 Press the button on the remote control to display the three different modes on the TV screen. Press the symbol 1 / button to highlight the personal mode as shown. Press the MENU button to display the menu on the TV screen. 2 3 SELECT MENU Press the button on the remote control to display the three different modes on the TV screen. Press the button to highlight the personal mode symbol as shown. Press the MENU button to display the menu on the TV screen. SELECT MENU OFF OFF 4 PROGR Press the blue button on the control to select the symbol on the TV screen then press the yellow button. 4 SELECT Press the blue button to select the symbol on the TV screen then press the yellow button. SELECT PROGR OFF OFF 7 5 Press the blue button to select the item you wish to change (see below). RM-883 5 IIIIIIIIIIIIIII - - - - - IIIIIIIIIIIIIII - - - - - IIIIIIIIIIIIIII - - - - - - Press the blue button to select the item you wish to change (see below). RM-883 IIIIIIIIIIIIIII - - - - - IIIIIIIIIIIIIII - - - - - - MONO STEREO DSP ON OFF IIIIIIIIIIIIIIIIIIIIIII - - - - - IIIIIIIIIIIIIIIII - - - - - - - - IIIIIIIIIIIIIII- -IIIIIIIIIIIIIII 0 6 Press the red or yellow button to alter the selected item. 6 Press the red or yellow button to alter the selected item. 7 Press the MENU button to remove the menu display from the TV screen. 7 Press the MENU button to remove the menu display from the TV screen. Symbol Symbol Item • • • • • • • Contrast Colour Brightness Sharpness Hue control (only for NTSC video signals) Reset - resets to factory preset picture level Picture rotation - adjusts picture tilt (only for KV-29C5D model) • Represents the mode selected in the “Using Select Mode” section. DSP 9 10 Item • Mono sound/Stereo sound A: Channel 1 sound/B: Channel 2 sound (to select your desired language from a dual sound broadcast) • On/Off (digital sound processor) • Treble • Bass • Balance • Reset (resets to factory preset sound level) • Represents the mode selected in the “Using Select Mode” section of the manual. Additional TV Features Additional TV Features Using the Sleep Timer Viewing Teletext The TV may be set to switch automatically to the standby mode after a length of time chosen by you. You may set the time in 15 minute steps up to 4 hours. Teletext is an information service transmitted by most TV stations. 1 / Press the MENU button on the remote control to display the menu on the TV screen. Selecting Teletext SELECT / SELECT OFF OK OFF 2 Press the blue button on the control to select the symbol on the TV screen, then press the yellow button. 1 Press a number button on the remote control to select the channel which carries the teletext service you wish to receive. 2 Press the button on the remote control to switch on teletext. SELECT TELETEXT TELETEXT Index Index Programme 25 News 153 Sport 101 Weather Programme 153 Sport 101 Weather OFF 3 Input three digits for the page number using the numbered buttons on the control. 4 Press the MENU 3 Press the yellow button repeatedly until the required amount of time delay appears on the screen. MENU SELECT 1:00 button to switch off teletext. Note: Teletext errors may occur if the broadcasting signals are weak. PROGR PROGR 4 Using Other Teletext Functions 8 Once the time delay has been selected, press the MENU button to remove the on-screen display. TELETEXT To Superimpose Teletext on to the TV Index Programme RM-883 One minute before standby, the display shown appears on the screen. 0:59 RM-883 once in teletext mode or twice in TV mode to Press superimpose teletext on to the TV screen. Press 153 Sport 101 again to cancel teletext mode. TELETEXT Index To Move to Next or Preceding Page Press PROGR +/- on the remote control to select the previous or next page. Notes: • When watching TV, press the time remaining. button to display To Freeze a Teletext Page on the control to freeze the page. Press Press again to cancel the freeze. • To return to normal operation from standby mode, button. press the / Revealing concealed information (eg: answers to a quiz). to reveal information. Press Press again to conceal the information. Using colour buttons to access pages (Fastext) When the colour coded menu appears at the bottom of a page, press the colour button (green, red, yellow or blue) to access the corresponding page. 11 12 Programme 25 News 153 Sport 101 Weather 25 News Weather 98 25 News 98 98 98 Additional TV Features Additional TV Features Exchanging Programme Positions Manually Tuning the TV After tuning you may wish to change the order in which the channels appear on the TV. You may wish for example to exchange the channel on programme number 8 with the channel on programme number 4. You have already tuned the TV to receive all available channels using the `Automatically Tuning the TV' procedure at the start of this manual. You can however carry out this operation manually using the following instructions. 1 Press the MENU button on the remote control. 1 SELECT / / SELECT OFF OK Press the MENU button on the remote control to display the menu on the TV screen. SELECT SELECT OFF OFF 2 Press the blue button on the control to select the TV screen, then press the yellow button. on OK OFF 2 SELECT Press the blue button to select the symbol on the TV screen then press the yellow button. SELECT OFF OFF 3 Press the blue button to select yellow button. then press the MENU PROGR C S CH 05 3 01 IIIIIIIIIIIIIII - - - - - F MENU on COO 4 PROGR 4 With the cursor pointing at PROGR on the TV screen as shown, press PROGR + or - button until the channel you wish to rearrange appears on screen, then press the blue button once. PROGR - + 01 PROGR With the cursor pointing at PROGR on the TV screen as shown, press PROGR + or - button on the remote control to allocate a programme number to the channel (eg PROGR 01). For double digit numbers e.g. 55, press the -/-- button on the remote control then the corresponding numbered buttons. PROGR C S CH 05 Press the blue button to select the channel type (C to preset a regular channel or S to preset a cable channel) then press the yellow button to highlight the desired channel type. PROGR C S CH 05 Press the blue button to select the tuning bar scale then press the yellow or red button once to start the channel search. (Yellow to search up the scale or red to search down). When a channel is found it appears on the TV screen. PROGR C S CH 05 F COO F COO 01 IIIIIIIIIIIIIII - - - - on 01 IIIIIIIIIIIIIII - - - - on 9 RM-883 5 6 7 8 Press the red or yellow button to select the new programme number (e.g. PROGR 04) for your selected channel. Press the blue button to select then press the yellow button to exchange the channels. 5 RM-883 PROGR - + 04 6 If you do not wish to store this channel on the programme number you selected, press the yellow or red button to continue searching for the desired channel. 7 If this is the channel you wish to store, press the symbol on the screen blue button to select the then press the yellow button to store. PROGR - + 04 F COO PROGR C S CH 05 F COO Repeat steps 4 to 6 if you wish to change the order of the other channels on your TV, then press MENU to return to normal TV screen. 8 Press the PROGR+/- button to view your selected channels on their new programme numbers. 13 14 Repeat steps 3 to 7 if you wish to store more channels then press the MENU button to remove the menu from the TV screen. 01 IIIIIIIIIIIIIII - - - - on 01 IIIIIIIIIIIIIII - - - - on Additional TV Features Optional Connections Fine-Tuning Channels Using Optional Equipment If a channel is slightly off tune, you can use this fine tune procedure to obtain a better picture reception. You can connect optional audio or video equipment to your TV, such as a VCR, a camcorder or video games as shown. 1 / 2 With the channel you wish to fine-tune on the screen, press the MENU button on the remote control. The menu display appears on the TV screen. Press the blue button on the remote control to symbol on the TV screen then press select the the yellow button. SELECT OFF OK OFF 1 Connect your equipment to the designated TV socket. 2 Press the button repeatedly on your remote control until the correct input symbol appears on the TV screen. Symbol 1 Press the blue button to select the F symbol on the TV screen then press the red or yellow button to adjust the tuning. PROGR C S CH 05 F COO 01 IIIIIIIIIIIIIII - - - - - s Press the blue button to select the symbol on the TV screen then press the yellow button to store. PROGR C S CH 05 10 F COO A B C D 8mm/Hi8 camcorder • Audio/video input signal through the Euro AV connector E or the phono sockets C and D • S video input signal through the socket B . + MONO + P _ s _ 2 L/G/S/I R/D/D/D 2 on PROGR 4 • Audio/video input signal through the Euro AV connector F • RGB input signal through the Euro AV connector F 2 3 Input signals SELECT OFF MENU Front of TV Select and View the Input Signal SELECT 3 Switch on the connected equipment. 4 To return to normal TV picture, press the control. button on the remote S-VHS/Hi8 camcorder 01 Note: To avoid picture distortion, do not connect equipment to the B , C or E connectors at the same time. IIIIIIIIIIIIIII - - - - on Rear of TV RM-883 5 Additional Information Press the MENU button to remove the menu from the TV screen. Connecting a VCR We recommend you tune in the VCR signal to TV programme number `0' using the `Manually Tuning in the TV' section of this instruction manual. E F G Connecting Headphones Plug in your headphones to the socket A on the front of the TV set. Connecting Decoders Plug in decoders to the socket F on the rear of the TV. s 2/ L/G/S/I 1/ R/D/D/D Connecting to External Audio Equipment Plug in your Hi-Fi equipment to the G sockets on the rear of the TV if you wish to amplify the audio output from the TV. 1 2 Playstation VCR 15 Hi-Fi 17 Additional Information Troubleshooting Specifications Here are some simple solutions to problems which may affect the picture and sound. Problem Solution No picture (screen is dark), no sound • Plug the TV in. button on the front of TV. • Press the • If the indicator is on press / button or a programme number button on the remote control. • Check the aerial connection. • Check that the selected video source is on. • Turn the TV off for 3 or 4 seconds and then turn it on again using the button on the front of the TV. Poor or no picture (screen is dark), but good sound • Using the MENU system, select the Picture Adjustment display. Adjust the brightness, picture and colour balance levels. to • From the Picture Adjustment display select return to the factory settings. • Press the button repeatedly on the remote control is displayed on the screen. until the RGB symbol Good picture, no sound • Press the +/– button on the remote control. is displayed on the screen, press the button • If on the remote control. 11 Poor picture quality when watching a RGB video source. TV system I Colour system PAL NTSC 3.58, 4.43 (only Video In) Channel coverage UHF: B21-B69 Picture tube KV-25K5U: Super Trinitron Approx. 63 cm (25 inches) (Approx. 59 cm picture measured diagonally), 110 deflection KV-29K5U: Super Trinitron Approx. 72 cm (29 inches) (Approx. 68 cm picture measured diagonally), 110 deflection Inputs • Rear Terminals 1/ 2/ 21-pin Euro connector (CENELEC standard) including audio/video input, RGB input, TV audio/video output s 21-pin Euro connector (CENELEC standard) including audio/video input, S-video input, Monitor audio/video output • Front Terminals 2 video input - phono jack 2 s audio inputs - phono jacks S video input - 4 pin DIN • Using the MENU system, select the Picture Adjustment display. Adjust the colour balance. to • From the Picture Adjustment display select return to the factory settings. Outputs Headphones jack - minijack stereo Audio outputs - phono jacks Distorted picture when changing programmes or selecting teletext • Turn off any equipment connected to the 21 pin Euro connector on the rear of the TV. Power consumption KV-25K5U: 139 W KV-29K5U: 158.5 W Remote control does not function • Replace the batteries. Standby Power consumption 1W No colour on colour programmes • If you continue to have these problems, have your TV serviced by qualified personnel. • NEVER open the casing yourself. Sound output: 2 x 10 W (RMS) Dimensions (wxhxd) KV-25K5U: Approx. 612 x 515 x 485 mm KV-295KU: Approx. 679 x 581 x 526 mm Weight KV-25K5U: KV-29K5U: Approx. 37 kg Approx. 49.5 kg Accessories supplied RM-883 Remote Control (1) IEC designated batteries (2) Other features TELETEXT, Fastext Design and specifications are subject to change without notice. 18 19 SECTION 2 DISASSEMBLY 2-1. REAR COVER REMOVAL 3 Rear Cover 2 8 Screws BTV 4x16 1 1 Screw BTV 4x16 2-2. CHASSIS ASSY REMOVAL 12 2-3. SERVICE POSITION 2-4. H1 BOARD REMOVAL 2-5. S1 BOARD REMOVAL Release the clip indicated. To release, push the claws in the direction of the arrow as indicated. 13 2-6. PICTURE TUBE REMOVAL 11 Two DGC holders 12 Degaussing coils 6 Chassis assy 13 Spring Extension 5 Speaker box 7 C board 4 Two screws 8 VM Board 9 Neck assy (KV-29K5 only) (KV-29K5 only) 14 Four PT 10 Deflection yolk screws (M) 3 Speaker box 1 Anode cap 2 Two screws 15 Picture tube Cushion • REMOVAL OF ANODE-CAP Note : Short circuit the anode of the picture tube and the anode cap to the metal chassis, CRT shield or carbon paint on the CRT, after removing the anode. * REMOVING PROCEDURES. c a b b Anode button 1 Turn up one side of the rubber cap in the direction indicated by the arrow a 2 Using a thumb pull up the rubber cap 3 When one side of the rubber cap is firmly in the direction indicated by the separated from the anode button, the arrow b anode-cap can be removed by turning up the rubber cap and pulling it up in the direction of the arrow c • HOW TO HANDLE THE ANODE-CAP 1 2 To prevent damaging the surface of the anode-cap do not use sharp materials. Do not apply too great a pressure on the rubber, as this may cause damage to the anode connector. A metal fitting called a shatter hook terminal is fitted inside the rubber cap. Do not turn the rubber foot over excessively this may cause damage if the shatter hook sticks out. 3 14 REMOVAL AND REPLACEMENT OF THE MAIN-BRACKET BOTTOM PLATES. (1) REMOVING THE PLATES £ (2) In the event of servicing being required to the solder side of the A Board printed wiring board, the bottom plates fitted to the main chassis bracket require to be removed. This is performed by cutting the gates with a sharp wire cutter at the locations shown and indicated by arrows. For safety reasons, on no account should the plates be removed and not refitted after servicing. REFITTING THE PLATES Because the plates differ in size it is important that the correct plates are refitted in their original location. Please note that the plates need to be rotated 180 degrees from the cut position to allow the tabs to be fitted in the catch positions. Note :There are 2 plates fitted to the main bracket and secured by 4 gates. Only remove the necessary plate to gain access to the printed wiring board. Catch Catch Gate Gate Catch 15 Gate Tab Gate Tab Tab Gate Tab Gate Catch Refitting Tab Gate Catch Gate SECTION 3 SET-UP ADJUSTMENTS • • • When complete readjustment is necessary or a new picture tube is installed, carry out the following adjustments. Unless there are specific instructions to the contrary, carry out these adjustments with the rated power supply. Unless there are specific instructions to the contrary, set the controls and switches to the following settings : Contrast ............... 80% [or remote control normal] Brightness ............... 50% Carry out the following adjustments in this order : 3-1. 3-2. 3-4. 3-3. Note : 2. Test equipment required 1. Color bar/pattern generator. 2. Degausser. 3. Oscilloscope. 4. Digital multimeter. 5. DC Power supply. Fig. 3-2 Preparation: 1. Beam Landing Convergence Focus White balance For 29" models align the neck assy as indicated below. In order to reduce the influence of geomagnetism on the set’s picture tube, face it in an easterly or westerly direction. Switch on the TV set’s power and degauss with the degausser. Purity Control 3-1. BEAM LANDING A buckle Neck Assy 1. 2. 3. 4. 5. 6. 7. Input an all-white signal from the pattern generator. Set the Contrast and Brightness to normal. Set the pattern generator raster signal to all Red. Move the deflection yolk forward and adjust with the purity control so that the Red is at the centre and the Blue and Green take up equally sized areas on each side of the screen. [See Fig.3-1 - 3-3]. Move the deflection yolk forward and adjust so that the entire screen becomes Red. [See Fig.3-1]. Switch the raster signal to Blue, then to Green and verify the purity condition. When the position of the deflection yolk has been determined, fasten the deflection yolk with the screws. If the beam does not land correctly in all the corners, use magnets to correct it. [See Fig.3-4]. G1 G2 Deflection Yoke GREEN RED BLUE Fig. 3-3 Disk magnets or rotatable disk magnets correct these areas (a - d). Purity control corrects this area. a b c d Deflection yolk positioning corrects these areas. a c b Fig. 3-1 d Fig. 3-4 16 3-2. CONVERGENCE • Tilt the V.STAT magnet and adjust the static convergence by opening or closing the V.STAT magnet. 4. If the V.STAT magnet is moved in the direction of the a and b arrows, the Red, Green and Blue points move as indicated below. Preparation: • • • Before starting this adjustment, adjust the focus, horizontal size and vertical size. Minimize the Brightness setting. Input a dot pattern from the pattern generator. (1) Horizontal and vertical static convergence Centre dot R G B R G B V.STAT Magnet H.STAT C Board RV701 SCREEN RV702 1. 2. 3. [Moving horizontally], adjust the H.STAT control so that the Red, Green and Blue points are on top of each other at the centre of the screen. [Moving vertically], adjust the V.STAT magnet so that the Red, Green and Blue points are on top of each other at the centre of the screen. If the H.STAT variable resistor is unable to bring the Red, Green and Blue points together at the centre of the screen, adjust the horizontal convergence with the H.STAT variable resistor and the V.STAT magnet in the manner indicated below. [In this case, the H.STAT variable resistor and the V.STAT magnet influence each other]. 17 (2) Operation of the BMC (Hexapole) magnet. R G R B R G B B R G B G R R G B G B V.STAT Purity BMC (Hexapole) • The respective dot position resulting from moving each magnet interact, so be sure to perform adjustment whilst tracking. Use the H.STAT VR to adjust the Red, Green and Blue dots so that they coincide at the centre of the screen [by moving the dots in the horizontal direction]. (3) Dynamic convergence adjustment. Preparation: • 1. 2. 3. Before starting this adjustment, adjust the horizontal and vertical static convergence. Slightly loosen the deflection yolk screws. R B G B R R G B G B G G B 4. 5. Remove the deflection yolk spacer. Move the deflection yolk as indicated in the figure below and optimize the convergence. Tighten the deflection yolk screws. Re-install the deflection yolk spacer. G B B R G B R B R R G R R G B G R B G R 18 R G B 3-3. Screen [G2], White balance (4) Screen corner convergence. • If you are unable to adjust the corner convergence properly, this can be corrected by the use of permalloy assemblies. a G2 Setting 1. 2. 3. b 4. a-d: screen-corner convergence defect d c Input a dot signal from the pattern generator. Set the Picture, Brightness and Colour to minimum. Apply 170Vdc from an external power supply to the R, G and B cathodes of the CRT. Whilst watching the picture, adjust the G2 control [RV701 SCREEN] located on the C Board to the point just before the flyback return lines disappear. White balance adjustment 1. 2. 3. 4. 5. Fit the permalloy assembly to the rear of the CRT to correct the area at fault. 6. 7. 8. a 10. b Input a ‘PAL’ all-white signal from the pattern generator. Enter into the Service Mode. Enter into the ‘Picture’ service menu. Select the ‘Green drive’ and adjust so that the White Balance becomes optimum. Select the ‘Blue drive’ and adjust so that the White Balance becomes optimum. Set the Picture to MIN. Set the ‘R-cut-off’ to 07. Adjust the ‘G-cut-off’, and the ‘B-cut-off’ so that the White Balance becomes optimum. Press the button to return to TV operation. PICTURE Permalloy c d R - Drive Adj G - Drive Adj B - Drive Adj R - cut - off Adj G - cut - off Adj B - cut - off Adj ID - start 02 ID - stop 01 ID - level 01 Bellfo Adj Sub Colour Adj Sub Brightness Adj 3-4. FOCUS 1. 2. 3. Input a Phillips colour pattern Set the picture settings to normal. Adjust the focus control located on the Flyback transformer to bring the centre of the screen into focus. Note :Bring only the centre area of the screen into focus, switch to an all-white pattern and confirm that the magenta ring is hardly noticed. To obtain optimum focus balance the focus setting between optimum screen centre focus and a reduced magenta ring level. FOCUS 19 SECTION 4 CIRCUIT ADJUSTMENTS 4-1. ELECTRICAL ADJUSTMENTS Service adjustments to this model can be performed using the supplied Remote Commander RM-883. PICTURE HOW TO ENTER INTO SERVICE MODE 1. 2. Turn on the main power switch and enter into the stand-by mode. Press the following sequence of buttons on the Remote Commander. i+ 5 + (ON SCREEN DISPLAY) (DIGIT 5) (VOLUME +) • 3. (TV) ‘TT--’ will appear in the upper right corner of the screen. Other status information will also be displayed. Press ‘MENU’ on the remote commander to obtain the following menu on the screen. > Picture 5. 6. Adj G - Drive Adj B - Drive Adj R - cut - off Adj G - cut - off Adj B - cut - off Adj ID - start 02 ID - stop 01 ID - level 01 Bell-f0 Adj Sub Colour Adj Sub Brightness Adj GEOMETRY TEST MENU 4. R - Drive V centre Adj V size Adj V Lin Adj S Corr Adj H Cent Adj H Size Adj Pin Amp Adj Geometry Corner Pin Adj Sound Pin Phase Adj TV Status V Bow Adj AGC Adjust V Angle Adj Technical Upper V Lin Adj Lower V Lin Adj Left HBLK 07 Right HBLK 07 CD Mode (AV) 01 Move to the corresponding adjustment item using the ‘Green’ [up] or ‘Blue’ [down] buttons on the Remote Commander. Press the ‘Yellow’ button to enter into the required menu item. Press the ‘Menu’ button on the Remote Commander to quit the Service Mode when all adjustments have been completed. SOUND Nicam Error Lower 20 Nicam Error Upper 80 Nicam Error Rate xx [Status only] AGC Gain Level xx [Status only] TV STATUS Note :The data shown in the ‘TV STATUS’ table is dependant on destination and country. 20 Destination A/L/E/U/D/B/K/R Text Language East/West Note: Ensure that no signal is applied to the Antenna socket while carrying out the following IF adjustments. TECHNICAL SYSTEM B/G, D/K, I & L I.F ADJUSTMENT GD - Secam 30 BD - Secam 31 RC - Secam 11 GC - Secam 19 BC - Secam 10 GD - Sports 30 BD - Sports 36 RC - Sports 14 GC - Sports 15 BC - Sports 17 Y - Delay (AV) 07 1. 2. 3. SYSTEM L BAND 1 I.F ADJUSTMENT 1. 2. 3. 4. SUB BRIGHTNESS ADJUSTMENT 1. 2. 3. 2. 3. 4. 5. Input a 34.0MHz carrier signal at 100dBuV to Pin 11 [IF output] of the tuner [TU101]. Select ‘system L’ + C00 [channel 00]. Measure the voltage at Pin 17 [IC101]. Adjust RV101 [A Board] to obtain a voltage of 2.5V +/- 0.3V. TUNER AGC ADJUSTMENT Input a Phillips colour pattern. Press ‘TEST’ ‘TEST’ 13 on the Remote Commander. Adjust the ‘Sub-Brightness’ data so that there is barely a difference between the 0 IRE and 10 IRE signal levels. 1. 2. 3. 4. 5. SUB CONTRAST ADJUSTMENT 1. Input a 38.9Mhz carrier signal at 100dBuV to Pin 11 [IF output] of the tuner [TU101]. Measure the voltage at Pin 17 of [IC101]. Adjust L103 [A Board] to obtain a voltage of 2.5V +/- 0.3V. Input a video signal that contains a small 100% white area on a black background Set the picture control to maximum. [‘TT01’] Connect an oscilloscope to Pin 1 of CN504 [A Board]. Enter into the ‘Picture’ service menu. Adjust the ‘R - Drive’ data to obtain the following waveform. Receive a signal of 65dBuV / 75 ohm terminated, via the tuner antenna socket. Connect a voltmeter to JW130 [A Board]. Enter into the ‘Test Menu’. Select the ‘AGC Adjust’ menu item. Adjust the data using the Yellow and Green buttons on the Remote Commander to obtain a voltage of 3.0V +/- 0.2V. A 25" 2.21V +/- 0.01V 29" 2.52V +/- 0.01V RV101 R - out Waveform IC101 17 SUB COLOUR ADJUSTMENT 1. 2. 3. 4. L103 Receive a PAL colour bar signal. Connect an oscilloscope to Pin 3 of CN504 [A Board]. Enter into the ‘Picture’ service menu. Adjust the ‘Sub Colour’ data so that the Cyan, Magenta and Blue colour bars are of equal levels as indicated below. 11 JW130 TUNER Same Level A Board component side B-Out Waveform 21 BELL FILTER ADJUSTMENT (Secam models only). V SIZE Note : Ensure that the TV set has been powered up for at least 1 minute to allow for drift before carrying out the following adjustment. 1. 2. 3. 4. V LIN Input a video SECAM Colour Bar signal via AV1. Connect an oscilloscope to pin 1 of CN504 [R-OUT] on the A board. Enter into the ‘Picture’ menu and select ‘Bell-f0’. Decrease the register of ‘Bell-f0’ until the following waveform change between RED and BLUE is obtained. S CORRECTION V CENTRE H CENTRE H SIZE Before adjustment 5. After adjustment When the correct waveform has been obtained add an additional 7 steps to the register. PIN AMP DEFLECTION SYSTEM ADJUSTMENT 1. 2. PIN PHASE Enter into the ‘Geometry’ service menu. Select and adjust each item in order to obtain the optimum image. CORNER PIN GEOMETRY V ANGLE V centre Adj V size Adj V Lin Adj S Corr Adj H Cent Adj H Size Adj Pin Amp Adj Corner Pin Adj Pin Phase Adj V Bow Adj V Angle Adj Upper V Lin Adj Lower V Lin Adj Left HBLK 07 Right HBLK 07 CD Mode (AV) 01 22 4-2. TEST MODE 2: Is available by pressing ‘TEST’ button twice, OSD ‘TT’ appears. The functions described below are available by pressing the two numbers. To release the Test mode 2, press 0 twice, or switch the TV into stand-by mode, or press the TV button on the remote commander. 00 Cancel Test mode 42 Re-initialise geometry settings [Only when Prog=59] 01 Picture maximum 43 No function 02 Picture minimum 44 No function 03 Volume 35% 45 No function 04 Volume 50% 46 No function 05 Volume 65% 47 No function 06 Volume 80% 48 Set NVM as NON Virgin [Only when Prog=59] 07 Ageing mode On/Off 49 Set NVM as Virgin [Only when Prog=59] 08 Set shipping conditions 50 No function 09 Display TV Status 51 No function 10 No function 52 No function 11 Sub Picture Adjustment 53 No function 12 Sub Colour Adjustment 54 No function 13 Sub Brightness Adjustment 55 No function 14 Text H position Adjustment 56 No function 15 Rotation test 57 No function 16 Picture level 50% 58 No function 17 Audio mute ON 59 No function 18 Disable Blanking 60 No function 19 No function 61 Auto AGC Adjust 20 No function 62 Alternative Dest B Autotuning 21 Destination A 63 Enable/Disable Y/C input 22 Destination L 64 Signal Quality Check for Auto Tune 23 Destination E 65 Signal Quality NOT Checked for Auto Tune 24 Destination U 66 No function 25 Destination D 67 Manual AGC Adjust 26 Destination B 68 -100 No function 27 Destination K 28 Destination R 29 No function 30 No function 31 Auto shutoff Disable/Enable 32 RGB priority Disable/Enable 33 Rotation On/OFF 34 Text language East/West 35 Wide CRT/4:3 CRT 36 VM ON/OFF test 37 No function 38 No function 39 No function 40 No function 41 Re-initialize the NVM [Only when Prog=59] 23 4-3. FE-1 SELF DIAGNOSTIC SOFTWARE The identification of errors within the FE-1 chassis is triggered in one of two ways :- 1: Busy or 2: Device failure to respond to IIC. In the event of one of these situations arising the software will first try to release the bus if busy (Failure to do so will report with continuous flashing LED) and then communicate with each device in turn to establish if a device is faulty. If a device is found to be faulty the relevant device number will be displayed through the LED (Series of flashes which must be counted) See Table 1., non fatal errors are reported using this method. Each time the software detects an error it is stored within the NVM. See Table 2. How to enter into Table 2 Table 1 1. LED ERROR COUNT ERROR No error 00 Not allowed (may be confused with Sircs response flash!) 01 Protection circuit trip < ANY TIME > 02 Reserved 03 No vertical sync 04 AKB 05 2. Turn on the main power switch of the TV set and enter into the ‘Standby Mode’. Press the following sequence of buttons on the Remote Commander. i+ 5 (ON SCREEN DISPLAY) (DIGIT 5) 3. 06 NVM no IIC bus acknowledge at Power ON 07 Jungle controller no IIC acknowledge at Power ON 08 Tuner no acknowledge at Power ON 09 Error Sound processor no acknowledge at Power ON 10 2 3 4 5 6 7 8 9 10 Table 2 Flash Timing Example : e.g. error number 3 StBy LED ON OFF (TV) The following table will be displayed indicating the error count. IIC bus clock and/or data lines low at Power ON ON (VOLUME -) ON Times - OFF Note: To clear the error count data press ‘80’ on the Remote commander. 24 5-1 BLOCK DIAGRAMS (1) CN201 A( TUNER, POWER SUPPLY HV OUT AUDIO, MICRO CONTROLLER/TEXT YC JUNGLE VIF DECODER 4 ) R AUDIO TO SPEAKERS 1 L AUDIO 2 4 VIDEO AMP Q408, 409 IC101 VIF/SIF DEMODULATOR 1 HD 5 AF OUT 8 SCL QSS 12 TU101 DET OUT 16 BUFFER Q107 IF1 SWF 101 SWF 102 1 VIF 2 VIF 23 SIF 24 SIF AGC IC001 MICRO CONTROLLER BUFFER Q101 SDA 8 0-COIN 0-MSP/ASW STAND SW RF 3 4 0-RFAGC 9 I-AFT 9 BUFFER Q012 0-V BLK 17 IC201 AUDIO AMP 5 L IN/IN 2 9 STBY LIL SW 0- +B DROP 18 VAR/L MON OUT 0-VOL 2 SWITCH Q006 CN007 RESP 6 SIRCS 7 OSD BLK 35 O-KEY/SCART 13 SDAI CS VAR R/SW L OUT/NC 12 R OUT/OUT 14 3 RST 2 R1 L1 R2 CN602 DGC 6 AMPLIFIER Q007,008, 009 0-KEY SCART 19 0-LED 0-WP 7 7 48 I-PROCDES IC003 RESET A1 IC004 NVM 6 5 SCLO SCL TVR OUT 1 0-ROT/VC D-N-C 42 X-OUT 34 SCLO 2 - 6 + 3 + 2 - 7 +B PIN OUT Q532 1 AUDIO VCC 14 IC604 15 D610 RECT D511 1 1 T602 L AUDIO IN 5VREG 3 1 9VREG 3 +9V 1000V TO C BOARD CN701 200V T801 FBT HV 2 LOW B TO PICTURE TUBE 1 1 5 C 5 4 4 D 7 3 IC609 STANDBY POWER 4 6 DET V OUT MON OUT B8 HP IC608 D632 RECT 5V REG MODE 41 X-IN 0-XRAY PROT 52 EXT B IN 26 SWITCH Q011 HD GREEN A15 EXT R IN 28 RED D571, Q571,574 5 H-DRIVE Q535 DF 13 6 29" only 11 10 H-OUT Q533 D513 +15V RECT 8 V IN B2 ABL IN 3 AUDIO R IN 7 B6 D514 -15V RECT AUDIO L IN EW 11 VD+ 13 VD- 14 EW B15 C IN VD+ -15V B20 YV IN VD- 48 XTAL 1 HD CN504 HD 19 R OUT 22 47 XTAL 2 G OUT 23 1 RED 2 GREEN 3 B OUT 24 2 CI IN 4 Y1/CVBS IN BLUE TO C BOARD CN703 6 26 IK IN 21 IK 27 28 CN503 1 9 BLK ABL VP 37 TO VM BOARD CN1809 ABL A20 Y/CVBS IN 41 1 12 A16 EXT BLK 25 HP 18 PROTECT STBY +5V CN509 FV T531 HDT BLUE A11 EXT G IN 27 0-STBY 51 HP 36 3 +B DET L OUT 15 VM OUT 25 CN502 +5V MUTE SW Q202 L AUDIO IN A3 43 TV/C2 IN C D614 RECT J401 A19 SDAO AUDIO L C 7 A7 5 Y/CVBS 5 2 8 MON L OUT MON OUT 4 H- DY+ HP PROTECT RELAY SWITCH Q601 L AUDIO OUT B3 CN406 Y/CVBS IC603 ERROR AMP 5 S 2 MON R OUT 35 SDAO EXT CVBS 24 AUDIO R D 3 EW 1 16 43 RESET BUFFER Q013 6 DGC 12 A8 1 5 AUDIO R IC606 POWER D605 +B RECT DET R OUT X001 12MHZ TO H BOARD CN906 1 H DY H- DY- B1 CN505 8 4 13 MODE AUDIO L 11 VCC 4 DGC 6 A2 MON OUT VM OUT H- DY+ IC605 30 INT B2 IN SDA 8 TO VM BOARD CN1705 2 J404 31 INT G2 IN B 32 4 6 3 H1 G 33 SDAI NS CORRECT 3 H- DYH- DY+ V DY IC531 PIN CORRECTION 3 FBO CP 1 1 4 DGC CHECK MONO TO S1 BOARD CN1101 V- DY- 5 H- DY- T603 SRT R AUDIO OUT A6 I MODE 2 11 29" only DGC CHECK 16 17 I MODE 1 15 SCLI 1 REF MAIN RECT D601 RELAY RY601 TVL OUT 32 INT R2 IN 12 0-SCART 1/2 12 I-KEY 2 CN603 SIF 1 OUT 5 VD- V- DY+ 6 11 I-KEY-SCART I-KEY/SCART 1/2 10 AGC SDA BOOST V- DY- +B 29 INT BLK R 34 5 LINE FILTER T601 SCL 3 V- DY+ 2 20 0-BAND-L I-KEY/SCART 9 SCLI 2 1 4 IN 4 STBY 5V SIRCS 2 15 NC/IN 2 16 0-BAND-L IC005 SWITCH SCART MATRIX RESP VP L2 1 7 2 R AUDIO OUT 12 4 IC301 Y/C JUNGLE KEY 14 I-KEY CN001 11 10 MUTE 15 0-BAND-M 4 VOLUME 14 AGC DEFEAT 0-SP MUTE 30 KEY 3 10 AGC MON SDA TO H BOARD CN907 10 14 R IN/IN 3 SCL 2 6 14 TU AGC 7 TO H1 BOARD CN604 3 1 4 3 21 BE/DK/I AGC 22 AFC 17 TO H1 BOARD CN908 DY ASSY VD+ CN606 CN101 1 5 SYNC SEP Q005, 004 L AUDIO IN R AUDIO IN L AUDIO OUT IC501 V OUTPUT PH601 ISOLATOR CN208 29" only TO VM BOARD CN1803 5-1 BLOCK DIAGRAMS (2) S1 CN1101 SCL SDA (STEREO DECODER) 1 4 2 5 5-2. CIRCUIT BOARD LOCATION IC1101 STEREO DECODER SIF 5 12 6 XTAI OUT 2 + 3 - +9V VM ( 1 ) VM AMP, QP, DYNAMIC FOCUS ROTATION AMP 9 33 R1 TO A BOARD CN101 10 34 L1 11 5 - 6 + R2 7 14 TVR OUT IC1801 ROTATION AMP 6 ROT + 5 CN1705 7 TO A BOARD CN505 V PULSE 6 NS CORRECT 5 VM 1 7 2 AUDIO R OUT R AUDIO OUT + TO ROTATION COIL + ROT - 1 3 16 L AUDIO OUT 3 17 SCART 1 IN R 37 SCART 2 IN L 47 SCART 1 OUT 48 S601 MAIN OUT R 60 AUDIO/VIDEO IN, HEADPHONE JACK, AUDIO OUT JACK, SIRCS RECEIVER, FUNCTION SWITCH ) CN603 1 1 RB : NON FLAMMABLE CEMENT RW : NON FLAMMABLE WIREWOUND 2 2 TO A BOARD CN606 COIL LF-8L : MICRO INDUCTOR CAPACITOR TA : TANTALUM PS : STYROL PP : POLYPROPYLENE PT : MYLAR MPS : METALIZED POLYESTER MPP : METALIZED POLYPROPYLENE ALB : BIPOLAR Note : ALT : HIGH TEMPERATURE • • ALR : HIGH RIPPLE CN907 KEY TO A BOARD CN007 RESP AUDIO L OUT SIRCS 6 7 H1 Board FUNCTION SWITCH S900-S902 4 2 1 : ADJUSTMENT RESISTOR REMOTE CONTROL RECEIVER IC900 A Board 5-3. SCHEMATIC DIAGRAMS AND PRINTED WIRING BOARDS VM AMP BUFFER Q1704 NECK ASSY VM OUT Q1703,1706 VM 2 GND 4 QP+ CN1803 BUFFER Q1840, 1841 : NON FLAMMABLE METAL OXIDE 29” only S1 Board - VM AMP Q1701, 1702, 1708, 1709,1710 15V PULSE VM Board 61 AUDIO L OUT 1 : NON FLAMMABLE FUSIBLE RS CN604 AUDIO R OUT AUDIO L OUT MAIN OUT L H1( POWER TVL OUT SCART 1 IN L SCART 2 IN R TVR OUT SCART 1 OUT CN908 TO A BOARD CN503 : NON FLAMMABLE CARBON FUSE SIFI TVL OUT CN1801 - +9V TVL OUT FPRD 18 TVR OUT 15 : SOLID C Board SDA 36 12 L2 : METAL FILM RC 17 29 MONO IN MONO IC1901 COMPARATOR RN RESISTOR SCL XTAI IN 29” models only Reference Information QP- TO A BOARD CN208 VM 8 1 AUDIO L IN J900 5 AUDIO R IN AUDIO R OUT 6 2 • HEADPHONES 4 QP IC1902 DF COMPARATOR 2 - 3 + 2 1 5 + 6 - 1 QP T1901 7 DF 1 CN1809 TO A BOARD CN509 TO A BOARD CN504 3 6 R G R DRIVE, BKG Q702, 703 R OUT Q704 G DRIVE, BKG Q705, 706 G OUT Q 707 R • • B CUT OFF PICTURE TUBE AUDIO L AUDIO R B DRIVE, BKG Q708, 709 B OUT Q710 CN900 CN906 G B Note: The components identified by shading and marked £ are critical for safety Replace only with the part numbers specified in the parts list. Pitch : 5mm Electrical power rating : 1/4W CN703 +9V All capacitors are in µF unless otherwise noted. pF : µµF 50WV or less are not indicated except for electrolytic types. Indication of resistance, which does not have one for rating electrical power, is as follows. H R C V G 2 2 L 4 R TO A BOARD CN406 G 4 H V Chip resistors are 1/10W All resistors are in ohms. k = 1000 ohms, M = 1000,000 ohms • : nonflammable resistor. • : fusible resistor. • : internal component. • : panel designation or adjustment for repair. Note: Les composants identifies par une trame et par une marque £ sont d’une importance critique pour le securite. Ne les remplacer que par des pieces de numero specifie. VIDEO Y/CVBS C 1 6 3 8 4 Y/C 2 • CN701 1 TO A BOARD CN502 6 • • • • G2 H1 2 +200V H2 H2 D711 PROTECT RCV RV702 G2 (1000V) H STAT C RV701 G2 • : B + bus. • : B - bus. • : RF signal path. • : earth - ground. • : earth - chassis. SCREEN (RGB OUT) TO A BOARD T511 (FBT) 29 All variable and adjustable resistors have characteristic curve B, unless otherwise noted. All voltages are in Volts. Readings are taken with a 10Mohm digital mutimeter. Readings are taken with a color bar input signal. Voltage variations may be noted due to normal production tolerences. 30 31 32 WAVEFORMS A BOARD 1 PAL 1 1.0 Vp-p (H) 4 SECAM 2.6 Vp-p (H) 6 0.5 Vp-p (H) 10 14 1.1KVp-p (H) PAL 2.4 Vp-p (H) WAVEFORMS C BOARD 1 2 102 Vp-p (H) 3 95 Vp-p (H) 4 93 Vp-p (H) 24 Vp-p (H) SECAM 3.0 Vp-p (H) 3 1.3 Vp-p (H) 2.6 Vp-p (H) 8 1.4 Vp-p (H) 12 142 Vp-p (H) 15 SECAM 7 11 15 2 5.0 Vp-p (H) 12 Vp-p (H) 146 Vp-p (V) PAL 1.0 Vp-p (H) 1.3 Vp-p (H) 5 9 2 2.0 Vp-p (H) 13 56 Vp-p (V) 290 Vp-p (H) 5-4 SEMICONDUCTORS CD4052BCM STR-F6654 2SA1837 TDA9875 TDA9870 9 16 64 32 LETTER SIDE 8 1 (TOP VIEW) 1 1 31 ( TOP VIEW ) B LM358DR-EZ NJM4558M-TE2 NJM2903D C E 5 E C CATHODE B 2SC4793 TOP209P 8 MTZJ-T-77-33A MTZJ-33C MTZJ-7.5B RD3.9ES-B2 RD5.6ESB2 RD6.8ES-B2 RD7.5ESB2 RD9.1ES-B3 1SS119-25TD 1SS133T-77 ERA81-004TP1 ERA83-006 MTZJ-T-77-3.9B MTZJ-T-77-5.6B MTZJ-T-77-5.6C MTZJ-T-77-6.8A MTZJ-T-77-6.8C MTZJ-T-77-7.5C MTZJ-T-77-9.1A MTZJ-T-77-9.1A MTZJ-T-77-10 2SA933AS-QRT 2SA933AS-RT 2SC1740S-RT 5 STV9379 8 5 2SK2251-01-F19 ANODE 1 4 ( TOP VIEW ) 1 4 ( TOP VIEW ) LM393P TDA2822M TEA2124 B E SEL12108-D 3 2 5 4 7 6 7 8 C 1 6 TYA7805CTV TYA7809CTV 5 E BF871-127 B C ST24W08FM6TR 2 1 3 4 8 5 ( TOP VIEW ) SAA5497PS/MIA/038 SAA5497PS/MIA/039 SAA5497PS/MIA040 52 E C ( TOP VIEW ) DTA144ESA DTA144ESA-TP DTC114EK DTC114EKA-T146 DTC143TKA-T146 DTC144EKA-T-146R 2SA1037K-T-146R2SA1162-G 2SC2412K-QR 2SC2412K-T-146-R 27 BF421-AMMO 2SA1091-O TDA7495 1 B 4 1 26 ( TOP VIEW ) SBX1981-51 E 1 C B C ERD28-08S ERC06-15 FMN-G12S RG1CLF-B1 RGP10GPKG23 RU3YX-LF-C4 RU3YX-V1 RU-4AM-T3 1SS292T-77 AK04-V1 AU-012-V1 BYD33G BYD33GAMMO DINL20-TR ERB44-06TP1 EG-1Z-V1 EL1Z ERD28-06S CATHODE ANODE UF4005PK623 ANODE CATHODE CATHODE ANODE 15 E B 2SC688-LK TDA9818-V1 TDA9817-V1 SE-135N SE135N-LF12 24 DAN202K DAN202K-T146 IRF614 13 3 1 1 12 ( TOP VIEW ) 3 1 2 2 E 1 V OUT 2 V IN 3 GND C B B C 53 E 2 3 1 54 5-5. IC BLOCK DIAGRAMS A BOARD IC201 TDA7495 A BOARD IC501 STV 9379 2 6 2 3 VOLUME 1 FLYBACK GENERATOR 14 30K OP AMP - 1 POWER AMPLIFIER 5 + 7 9 MUTE/STBY PROTECTIONS THERMAL PROTECTION 10 VOLUME 60K 5 12 30K OP AMP 4 3 A BOARD IC101 TDA9817/V1 22 15 TUNER AGC 14 4 6 7 19 18 17 21 20 A BOARD IC606 STR-F6654 VOLTAGE REFERENCE VIF AGC 4 4 AFC DETECTOR 3 1 VIF AMPLIFIER 2 23 VCO TWO FPLL SIF AGC VIDEO DEMODULATOR AND AMPLIFIER LATCH DRIVE REG 2 T.S.D O.S.C 8 1 Iconst INTERCARRIER MODE SWITCH 5 O.V.P 16 QSS MIXER INTERCARRIER MIXER AM DEMODULATOR SIF AMPLIFIER 24 START FM-PLL DEMODULATOR 3 12 13 5 9 10 11 A BOARD IC301 CXA2060AS TRAP PAL 4.43MHz NTSC 3.58MHz SECAM 4.2 - 4.43MHz <TRAP OFF> COUNT DOWN MONITOR SW <FIELD FREQ> <CD MODE> <INTERLACE> VIDEO SW 9 <VIDEO SEL> <S SEL> V SYNC SEP <VSS> <VSS LPF> H SYNC SEP <HSS> SECAM VCO CAL. by 4.43MHz 27 26 25 3 VPROT <VNG> VM AMP (OFF YS/YM) R/G/B BLK <PON> <RGB ON> DRIVE AMP <R/G/B DRIVE> CLAMP DAC SW AKB <IKR> BRIGHT CONT <BRIGHT> Y/C MIX RGB CLAMP CLAMP DC TRAN <DC TRAN> ABL/PEAK LIM <ABL MODE> <ABL VTH> CLAMP RGB 2/2 COLOR AMP <COLOR> <C DFF> AXIS <COL MATRIX> DPIC <DPIC> <AGING> 31 30 29 42 EYUV CLAMP YUV SW <Y SEL> YUV OUT <C DECOD> 1H DELAY LINE (PAL/SECAM) 32 GAMMA AMP <GAMMA> DEEMPHASIS 28 PC BUS DECODER STATUS I/T 21 24 23 22 35 34 FILTER ALIGNMENT Y SW 7 6 PLL SECAM FM DEMOD ACC DET ATT CHROMA SW LIM AMP (ZAP) ACC AMP 43 4 BELL FILTER LINE BLK 39 38 37 36 CUTOFF CONT <R/G/B CUTOFF> BPF PAL 4.43MHz NTSC 3.58MHz <C BPF> 15 SW NTSC PAL,SECAM KILLER <KILLER OFF> PAL/NTSC DEMOD COLOR SYSTEM DISCRIMINATOR PAL ID <PAL/NTSC> <XTAL ID> PAL/NTSC COLOR KILLER <KILLER> SECAM ID <SECAM> <XTAL> <COL SYSTEM> <COL LOOP> <ID START> <ID STOP> <HUE> 1 PICTURE AMP <PICTURE> CHROMA AMP 41 5 DYNAMIC COLOR <DY COL> ACO DET. 2 46 YM SW APC <HUE> ACC AMP 47 C VCO 4.433619MHz 3.579545MHz 9.582058MHz Y32 SW 48 YS1 SW <RGB SEL> 45 AFC <APC GAIN> <FH HIGH> <H CENT> 20 DL PAL/NTSC 300 x 200nS SECAM 300 x 200nS <Y DELAY> LINE COUNTER V TIM GEN <UNDER SCAN> SHARPNESS DL SHARPNESS AMP <SHARPNESS> <SHP FO> <PREOVER> VD SAW FUNC <VON> <VSIZE> <V POSITION> WIDE SAW FUNC <ASPECT> <SCROLL> <UPPER VLIN> <LOWER VLIN> <V ZOOM> <V UNDER SCAN> V SAW GEN (50/50) VTIM EW PARABOLA FUNC <H SIZE> <TRAPEZIUM> <PIN AMP> <EW DC> <CORNER PIN> <FIELD ID> H SAW GEN H OSC <ZAP> PHASE DET <H POSITION> <AFC BOW> <AFC ANGLE> HPROT <HNG> H TIM GEN <H BLK> <LEFT HBLK> <RIGHT HBLK> 17 5 18 55 14 <S CORRECTION> <V LINEARITY> <EHT COMP> HD GEN <HD W> 19 IREF 10 12 REG 16 33 13 11 SECTION 6 EXPLODED VIEWS NOTE : • • Items with no part number and no description are not stocked because they are seldom required for routine service. The construction parts of an assembled part are indicated with a collation number in the remarks column. • Items marked “ * “ are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. 6-1. CHASSIS 7-685-663-79 x 1 7-685-663-71 x 8 6 7 8 11 9 5 10 1 2 4 3 REF. NO. 1 2 3 4 5 PART.NO £ £ £ £ 6 DESCRIPTION REMARK 1-571-433-21 *4-204-141-01 *4-202-531-01 1-765-286-11 1-453-264-11 SWITCH, PUSH (AC POWER) BRACKET, MAIN AC CORD LOCK (SC) CORD, POWER TRANSFORMER ASSY, FLYBACK (NX-1680/U2B4) (KV-25K5K) 1-453-265-11 TRANSFORMER ASSY, FLYBACK (NX-1681/U2B4) (KV-29K5K) 8-598-432-00 TUNER (FSS-BTP-AC411) REF. NO. PART.NO DESCRIPTION 7 8 *A-1652-054-A *A-1632-794-A *A-1632-795-A *A-1646-160-A X-4200-307-3 X-4200-304-2 4-203-713-11 4-203-705-11 S1 BOARD, COMPLETE A BOARD, COMPLETE (KV-25K5K) A BOARD, COMPLETE (KV-29K5K) H1 BOARD, COMPLETE COVER ASSY, REAR (KV-25K5K) COVER ASSY, REAR (KV-29K5K) COVER, REAR (KV-25K5K) C0VER, REAR (KV-29K5K) 9 10 11 56 REMARK 6-2. PICTURE TUBE 68 73 67 74 75 71 76 77 67 72 69 70 64 65 66 63 62 60 72 70 59 71 61 51 69 58 57 52 55 53 56 54 REF. NO. PART.NO DESCRIPTION 51 £ X-4200-306-5 X-4200-305-7 4-047-464-01 4-203-693-21 4-204-071-01 4-203-704-01 4-202-964-01 4-204-070-01 4-203-128-11 8-733-254-05 £ 8-733-856-05 £ £ £ £ £ 8-451-404-23 8-451-466-11 8-733-254-76 8-733-856-75 8-453-005-21 BEZNET ASSY (KV-25K5K) 52 & 55-57 BEZNET ASSY (KV-29K5K) 52 & 55-57 CATCHER PUSH DOOR, ORNAMENTAL PLATE, ORNAMENTAL BUTTON POWER SPRING GUIDE, LIGHT SHEET, BLOTTING PICTURE TUBE (SD-257)(M60LCS60X) (KV-25K5K) PICTURE TUBE (SD-269)(M68LCT60X) (KV-29K5K) DEFLECTION YOKE (Y25GXABA) (KV-25K5K) DEFLECTION YOKE (Y29GXC2B) (KV-29K5K) ITC (KV-25K5K) ITC (KV-29K5K) NECK ASSY PICTURE TUBE (NA297-M2) (KV-29K5K) 52 53 54 55 56 57 58 59 60 61 62 REMARK REF. NO. 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 57 PART.NO £ £ *A-1644-093-A *A-1638-112-A 4-369-318-31 1-416-465-11 1-416-654-11 4-203-390-01 4-203-877-01 4-203-878-01 1-505-484-11 1-505-674-11 1-505-673-11 4-039-358-01 4-308-870-00 1-452-094-00 1-452-032-00 X-4387-214-1 3-701-007-00 DESCRIPTION REMARK VM BOARD, COMPLETE (KV-29K5K) C BOARD, COMPLETE SPRING, TENSION COIL, DEMAGNETIZATION (KV-25K5K) COIL, DEMAGNETIZATION (KV-29K5K) CUSHION, DGC HOLDER, DGC BRACKET 25” (KV-25K5K) HOLDER, DGC BRACKET 29” (KV-29K5K) SPEAKER (2.6CM) SPEAKER MID RANGE (8CM) SPEAKER WOOFER (10CM) SCREW (4X16), (+) BV TAPPING CLIP, LEAD WIRE MAGNET, ROTATABLE DISK; 15MM Ø MAGNET, DISK; 10MM Ø PERMALLOY ASSY, CORRECTION BAND, BINDING SECTION 7 ELECTRICAL PARTS LIST • Items marked “ * “ are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. All variable and adjustable resistors have characteristic curve B, unless otherwise noted. RESISTORS All resistors are in ohms. F : nonflammable. When indicating parts by reference number, please include the board name. • CAPACITORS MF : mF, PF : mmF COILS MMH : mH , uH • • • A REF. NO. PART.NO DESCRIPTION REMARK REF. NO. *A-1632-794-A A BOARD, COMPLETE (KV-25K5K) ***************** *A-1632-795-A A BOARD, COMPLETE (KV-29K5K) ***************** PART.NO DESCRIPTION REMARK C041 C042 C043 C103 C105 1-163-205-00 1-126-933-11 1-126-935-11 1-104-665-11 1-126-965-11 CERAMIC CHIP 0.001MF ELECT 100MF ELECT 470MF ELECT 100MF ELECT 22MF 10% 20% 20% 20% 20% 50V 16V 16V 25V 50V C108 C109 C110 C111 C112 1-163-465-11 1-164-004-11 1-163-038-00 1-216-296-00 1-163-031-11 CERAMIC CERAMIC CERAMIC SHORT CERAMIC 0.25PF 50V 10% 25V 25V C115 C116 C117 C118 C119 1-164-489-11 1-126-961-11 1-126-961-11 1-163-038-00 1-163-141-00 CERAMIC CHIP 0.22MF ELECT 2.2MF ELECT 2.2MF CERAMIC CHIP 0.1MF CERAMIC CHIP 0.001MF 10% 20% 20% C129 C134 C135 C137 C138 1-126-963-11 1-128-551-11 1-164-004-11 1-163-017-91 1-165-319-11 ELECT 4.7MF ELECT 22MF CERAMIC CHIP 0.1MF CERAMIC CHIP 0.0047MF CERAMIC CHIP 0.1MF 20% 20% 10% 10% C139 C140 C143 C160 C201 1-163-031-11 1-163-031-11 1-104-664-11 1-163-017-00 1-104-666-11 CERAMIC CHIP 0.01MF CERAMIC CHIP 0.01MF ELECT 47MF CERAMIC CHIP 0.0047MF ELECT 220MF 20% 10% 20% 50V 50V 25V 50V 25V C203 C204 C206 C207 C208 1-126-942-61 1-126-942-61 1-126-960-11 1-126-972-11 1-126-960-11 ELECT ELECT ELECT ELECT ELECT 1000MF 1000MF 1MF 1000MF 1MF 20% 20% 20% 20% 20% 25V 25V 50V 50V 50V C215 C301 C302 C303 C304 1-164-004-11 1-163-038-00 1-126-967-11 1-101-004-00 1-126-964-11 CERAMIC CHIP 0.1MF CERAMIC CHIP 0.1MF ELECT 47MF CERAMIC 0.01MF ELECT 10MF 10% 25V 25V 16V 50V 50V 4-382-854-11 SCREW (M3X10), P, SW (+) < CAPACITOR > C004 C005 C006 C007 C008 1-163-038-00 1-163-105-00 1-163-105-00 1-126-935-11 1-126-964-11 CERAMIC CHIP 0.1MF CERAMIC CHIP 33PF CERAMIC CHIP 33PF ELECT 470MF ELECT 10MF 5% 5% 20% 20% 25V 50V 50V 16V 50V C009 C010 C011 C012 C013 1-126-965-11 1-126-959-11 1-126-965-11 1-126-959-11 1-163-017-00 ELECT ELECT ELECT ELECT CERAMIC CHIP 20% 20% 20% 20% 10% 50V 50V (KV-29K5K) 50V 50V 50V C016 C018 C019 C022 C024 1-164-004-11 1-164-232-11 1-163-038-00 1-126-935-11 1-104-665-11 CERAMIC CHIP 0.1MF CERAMIC CHIP 0.01MF CERAMIC CHIP 0.1MF ELECT 470MF ELECT 100MF 10% 10% 20% 20% 25V 50V 25V 16V 25V C025 C028 C029 C030 C031 1-130-495-00 1-163-117-00 1-163-077-00 1-104-665-11 1-163-017-00 FILM 0.1MF CERAMIC CHIP 100PF CERAMIC CHIP 0.1MF ELECT 100MF CERAMIC CHIP 0.0047MF 5% 5% 10% 20% 10% 50V 50V (KV-29K5K) 25V 25V 50V C032 C033 C035 C036 C037 1-163-077-00 1-164-004-11 1-164-232-11 1-163-017-00 1-163-017-00 CERAMIC CERAMIC CERAMIC CERAMIC CERAMIC 0.1MF 0.1MF 0.01MF 0.0047MF 0.0047MF 10% 10% 10% 10% 10% 25V 25V 50V 50V 50V C038 C039 C040 1-126-964-11 ELECT 10MF 1-163-017-00 CERAMIC CHIP 0.0047MF 1-163-125-00 CERAMIC CHIP 220PF 20% 10% 5% 50V 50V 50V CHIP CHIP CHIP CHIP CHIP 22MF 0.47MF 22MF 0.47MF 0.0047MF 58 CHIP 9PF CHIP 0.1MF CHIP 0.1MF 0 CHIP 0.01MF 50V 5% 20% 20% 16V 50V 50V 25V 50V 50V 25V 25V 50V 50V The components identified by shading and marked are critical for safety Replace only with the part number specified. REF. NO. PART.NO A DESCRIPTION C305 C307 C308 C309 C312 1-163-005-11 1-164-232-11 1-164-004-11 1-126-963-11 1-163-099-00 CERAMIC CERAMIC CERAMIC ELECT CERAMIC C313 C314 C316 C317 C319 1-163-099-00 1-163-038-00 1-163-259-91 1-136-169-00 1-126-964-11 C321 C322 C328 C329 C330 CHIP 470PF CHIP 0.01MF CHIP 0.1MF 4.7MF CHIP 18PF REMARK REF. NO. PART.NO DESCRIPTION REMARK 10% 10% 10% 20% 5% 50V 50V 25V 50V 50V C436 C437 C438 C443 C444 1-163-017-00 1-535-465-11 1-535-465-11 1-163-017-00 1-163-017-00 CERAMIC CHIP LEAD, JUMPER LEAD, JUMPER CERAMIC CHIP CERAMIC CHIP 0.0047MF (5.0MM) (5.0MM) 0.0047MF 0.0047MF 10% 50V 10% 10% 50V 50V CERAMIC CHIP 18PF CERAMIC CHIP 0.1MF CERAMIC CHIP 220PF FILM 0.22MF ELECT 10MF 5% 50V 25V 50V 50V 50V C445 C501 C502 C503 C504 1-163-017-00 1-126-968-11 1-163-038-00 1-126-968-11 1-106-220-00 CERAMIC CHIP 0.0047MF ELECT 100MF CERAMIC CHIP 0.1MF ELECT 100MF MYLAR 0.1MF 10% 20% 20% 10% 50V 50V 25V 50V 100V 1-126-963-11 1-164-004-11 1-104-664-11 1-164-232-11 1-163-038-00 ELECT 4.7MF CERAMIC CHIP 0.1MF ELECT 47MF CERAMIC CHIP 0.01MF CERAMIC CHIP 0.1MF 20% 10% 20% 10% 50V 25V 25V 50V 25V C505 C506 C507 C508 C509 1-136-173-00 1-164-232-11 1-126-933-11 1-126-960-11 1-137-047-11 FILM 0.47MF CERAMIC CHIP 0.01MF ELECT 100MF ELECT 1MF FILM 0.01MF 5% 10% 20% 20% 10% 50V 50V 16V 50V 400V C331 C332 C333 C334 C335 1-164-232-11 1-164-232-11 1-126-960-91 1-163-021-91 1-164-232-11 CERAMIC CERAMIC ELECT CERAMIC CERAMIC CHIP 0.01MF CHIP 0.01MF 1MF CHIP 0.0047MF CHIP 0.01MF 10% 10% 20% 10% 10% 50V 50V 50V 50V 50V C510 C511 C512 C513 C515 1-163-133-00 1-102-125-00 1-162-114-00 1-107-662-11 1-104-666-11 CERAMIC CHIP 470PF CERAMIC 0.0047MF CERAMIC 0.0047MF ELECT 22MF ELECT 220MF 5% 10% 50V 50V 2KV 250V 25V C336 C337 C338 C339 C350 1-164-232-11 1-164-232-11 1-126-967-11 1-163-038-00 1-163-017-91 CERAMIC CERAMIC ELECT CERAMIC CERAMIC CHIP 0.01MF CHIP 0.01MF 47MF CHIP 0.1MF CHIP 0.0047MF 10% 10% 20% C517 C518 C519 C520 C522 1-104-666-11 1-106-375-12 1-163-275-11 1-163-038-00 1-137-399-11 ELECT 220MF MYLAR 0.022MF CERAMIC CHIP 0.001MF CERAMIC CHIP 0.1MF FILM 0.1MF 20% 99% 5% 10% 50V 50V 50V 25V 50V 5% 25V 200V 50V 25V 50V C351 C401 C402 C403 C405 1-163-017-91 1-163-141-00 1-126-960-11 1-163-017-00 1-163-141-00 CERAMIC CERAMIC ELECT CERAMIC CERAMIC CHIP 0.0047MF CHIP 0.001MF 1MF CHIP 0.0047MF CHIP 0.001MF 10% 5% 20% 10% 5% 50V 50V 50V 50V 50V C531 C532 C533 C535 C536 1-126-964-11 1-163-037-11 1-163-017-00 1-163-251-11 1-115-522-11 ELECT 10MF CERAMIC CHIP 0.022MF CERAMIC CHIP 0.0047MF CERAMIC CHIP 100PF FILM 1MF 20% 10% 10% 5% 5% 50V 50V 50V (KV-29K5K) 50V 200V C406 C407 C408 C410 C413 1-126-960-11 1-126-964-11 1-126-964-11 1-126-964-11 1-163-141-00 ELECT ELECT ELECT ELECT CERAMIC CHIP 20% 20% 20% 20% 5% 50V 50V 50V 50V 50V C537 C538 C539 C540 C541 1-137-417-11 1-164-004-71 1-111-230-11 1-136-206-11 1-106-383-00 MYLAR 0.0047MF CERAMIC CHIP 0.1MF ELECT 1MF FILM 0.033MF MYLAR 0.047MF 10% 10% 20% 10% 10% 200V 25V 160V 400V 200V C414 C415 C416 C417 C418 1-126-960-11 1-163-017-00 1-126-964-11 1-163-141-00 1-126-960-11 ELECT 1MF CERAMIC CHIP 0.0047MF ELECT 10MF CERAMIC CHIP 0.001MF ELECT 1MF 20% 10% 20% 5% 20% 50V 50V 50V 50V 50V C542 C543 C545 C546 C547 1-162-134-11 1-162-134-11 1-126-960-11 1-130-895-00 1-117-813-11 CERAMIC CERAMIC ELECT FILM FILM 470PF 470PF 1MF 0.056MF 0.75MF 10% 10% 20% 5% 5% 2KV 2KV 50V 400V 200V C422 C423 C430 C432 C433 1-163-017-00 1-126-964-11 1-104-664-11 1-163-141-00 1-163-141-00 CERAMIC CHIP 0.0047MF ELECT 10MF ELECT 47MF CERAMIC CHIP 0.001MF CERAMIC CHIP 0.001MF 10% 20% 20% 5% 5% 50V 50V 25V 50V 50V C548 C550 C552 C553 1-162-134-11 1-107-638-11 1-102-212-00 1-137-417-11 CERAMIC ELECT CERAMIC MYLAR 470PF 33MF 820PF 0.0047MF 10% 20% 10% 10% 2KV 160V 500V 200V C555 C434 C435 1-126-935-11 ELECT 470MF 1-163-017-00 CERAMIC CHIP 0.0047MF 20% 10% 16V 50V 1-117-717-11 FILM 1-117-648-11 FILM 17000P 15000PF 3% 3% 1.2KV(KV-25K5K) 1.2KV(KV-29K5K) 1MF 10MF 10MF 10MF 0.001MF 5% 5% 20% 59 20% 20% The components identified by shading and marked are critical for safety Replace only with the part number specified. A REF. NO. PART.NO C571 C572 C580 C582 C584 C601 C602 C603 C604 C605 C606 C607 C609 C610 C611 C612 C613 C614 C615 C618 £ £ £ £ DESCRIPTION REMARK REF. NO. PART.NO 1-564-511-11 *1-580-798-11 *1-691-135-11 *1-564-507-11 *1-564-509-11 1-123-024-21 1-128-526-11 1-164-232-11 1-163-275-11 1-126-963-11 ELECT 33MF ELECT 100MF CERAMIC CHIP 0.01MF CERAMIC CHIP 0.001MF ELECT 4.7MF 20% 10% 5% 20% 160V 16V 50V 50V 50V CN406 CN501 CN502 CN503 CN504 1-107-563-11 1-107-563-11 1-117-700-51 1-117-700-51 1-104-652-11 FILM FILM CERAMIC CERAMIC ELECT 0.1MF 0.1MF 0.0022MF 0.0022MF 470MF 20% 20% 99% 99% 20% 300V 300V 250V 250V 10V CN505 *1-568-882-51 PIN, CONNECTOR CN506 1-695-915-11 TAB (CONTACT) CN509 *1-508-784-00 PIN, CONNECTOR CN602 £ 1-508-765-00 PIN, CONNECTOR CN603 £ 1-508-786-00 PIN, CONNECTOR CN606 £ *1-691-291-11 PIN, CONNECTOR 1-125-555-11 1-125-787-51 1-107-915-11 1-104-665-11 1-165-127-11 ELECT(BLOCK) CERAMIC ELECT ELECT CERAMIC 330MF 680PF 2200MF 100MF 470PF 20% 10% 20% 20% 10% 400V 2KV 50V 25V 500V 10% 20% 250V 250V 250V 400V 25V £ 1-161-964-51 CERAMIC £ 1-161-964-51 CERAMIC £ 1-161-964-51 CERAMIC 1-130-202-00 FILM 1-107-890-11 ELECT 0.0047MF 0.0047MF 0.0047MF 0.022MF 2200MF C621 C622 £ C624 C625 C628 1-163-005-11 1-161-964-51 1-104-665-11 1-104-665-11 1-124-347-00 CERAMIC CHIP 470PF CERAMIC 0.0047MF ELECT 100MF ELECT 100MF ELECT 100MF 10% 20% 20% 20% 50V 250V 25V 25V 160V C629 C630 C633 C635 C638 1-136-189-00 1-165-127-11 1-104-332-11 1-107-675-11 1-107-670-11 FILM CERAMIC CERAMIC ELECT ELECT 0.1MF 470PF 470PF 1MF 10MF 10% 10% 10% 20% 20% 250V 500V 2KV 160V 400V C639 C640 C641 C642 C646 1-104-665-11 1-104-664-11 1-104-665-11 1-104-665-11 1-107-974-11 ELECT ELECT ELECT ELECT CERAMIC 100MF 47MF 100MF 100MF 47PF 20% 20% 20% 20% 5% 25V 25V 25V 25V 2KV CF101 1-404-134-00 TRAP, CERAMIC (5.5MHZ) SWF101 SWF102 1-767-874-11 FILTER, SURFACE WAVE 1-767-873-11 FILTER, SURFACE WAVE < CONNECTOR > *1-564-508-11 *1-564-510-11 1-766-922-11 *1-564-507-11 *1-564-508-11 REMARK PLUG, CONNECTOR 8P CONNECTOR PIN (DY) 6P PIN, CONNECTOR (PC BOARD) 4P PLUG, CONNECTOR 4P (KV-29K5K) PLUG, CONNECTOR 6P 7P PLUG, CONNECTOR 5P PLUG, CONNECTOR 7P CONNECTOR, BOARD TO BOARD 18P PLUG, CONNECTOR 4P PLUG, CONNECTOR 5P 60 (KV-29K5K) (5MM PITCH) 1P (5MM PITCH) 3P (5MM PITCH) 2P (PC BOARD) 5P < DIODE > < FILTER > CN001 CN007 CN101 CN201 CN208 DESCRIPTION D001 D002 D004 D005 D007 8-719-109-89 8-719-109-89 8-719-109-89 8-719-109-89 8-719-109-89 DIODE DIODE DIODE DIODE DIODE RD5.6ESB2 RD5.6ESB2 RD5.6ESB2 RD5.6ESB2 RD5.6ESB2 D008 D009 D010 D011 D012 8-719-991-33 8-719-109-89 8-719-109-89 8-719-109-89 8-719-914-43 DIODE DIODE DIODE DIODE DIODE 1SS133T-77 RD5.6ESB2 RD5.6ESB2 RD5.6ESB2 DAN202K D014 D015 D017 D018 D023 8-719-058-24 8-719-914-43 8-719-109-89 8-719-991-33 8-719-109-89 DIODE DIODE DIODE DIODE DIODE RB501V-40TE-17 DAN202K RD5.6ESB2 1SS133T-77 RD5.6ESB2 D101 D201 D202 D204 D205 8-719-982-24 8-719-929-15 8-719-914-43 8-719-109-89 8-719-109-89 DIODE DIODE DIODE DIODE DIODE MTZJ-33A HZS9.INBZ DAN202K RD5.6ESB2 RD5.6ESB2 D206 D306 D307 D308 D309 8-719-109-89 8-719-109-89 8-719-109-89 8-719-109-72 8-719-991-33 DIODE DIODE DIODE DIODE DIODE RD5.6ESB2 RD5.6ESB2 RD5.6ESB2 RD3.9ESB2 1SS133T-77 D320 D402 D405 D406 D407 8-719-929-15 8-719-109-89 8-719-109-97 8-719-109-97 8-719-109-97 DIODE DIODE DIODE DIODE DIODE HZS9.INB2 RD5.6ESB2 RD6.8ES-B2 RD6.8ES-B2 RD6.8ES-B2 D408 D409 D410 D414 8-719-929-15 8-719-109-97 8-719-109-89 8-719-109-97 DIODE DIODE DIODE DIODE HZS9.INB2 RD6.8ES-B2 RD5.6ESB2 RD6.8ES-B2 (KV-29K5K) The components identified by shading and marked are critical for safety Replace only with the part number specified. REF. NO. PART.NO A DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK D415 D417 D418 D419 D422 8-719-929-15 8-719-929-15 8-719-929-15 8-719-929-15 8-719-109-97 DIODE DIODE DIODE DIODE DIODE HZS9.INBZ HZS9-INB2 HZS9-INB2 HZS9-INB2 RD6.8ES-B2 FB610 FB611 FB612 D423 D427 D501 D502 D511 8-719-109-97 8-719-109-97 8-719-302-43 8-719-924-13 8-719-028-72 DIODE DIODE DIODE DIODE DIODE RD6.8ES-B2 RD6.8ES-B2 EL1Z MTZJ-T-77-22B RGP02-17EL-6433 IC001 IC003 IC004 IC005 IC101 8-759-526-01 8-759-468-56 8-759-432-33 8-759-516-41 8-759-466-49 SAA5497PS/MIA/038 IC MN1381T IC ST24W08FM6TR IC CD4052BCM IC TDA9817/V1 D512 D513 D514 D534 D535 8-719-302-43 8-719-979-85 8-719-979-85 8-719-302-43 8-719-908-03 DIODE DIODE DIODE DIODE DIODE EL1Z EGP20G EGP20G EL1Z GP08D IC201 IC301 IC501 IC531 IC603 8-759-442-74 8-752-082-35 8-759-192-71 8-759-450-95 8-749-920-61 IC IC IC IC IC TDA7495 CXA2060AS STV9379 LM393N SE135N D536 D538 D539 D541 D571 8-719-945-80 8-719-908-03 8-719-900-26 1-535-465-11 8-719-911-19 DIODE DIODE DIODE LEAD, DIODE ERC06-15S GP08D ERD29-08J JUMPER (5.0MM) 1SS119-25 IC604 IC605 IC606 IC608 IC609 8-759-524-82 8-759-524-83 8-749-013-75 8-759-524-82 8-759-468-89 IC IC IC IC IC TYA7805CTV TYA7809CTV STR-F6654 TYA7805CTV TOP209P D573 D601 D602 D603 D605 8-719-921-40 8-719-510-53 8-719-046-74 8-719-312-61 8-719-312-10 DIODE DIODE DIODE DIODE DIODE MTZJ-4.7C D4SB60L AU-01Z-V1 EU-1Z RU4AM-T3 D608 D610 D613 D614 D619 8-719-067-88 8-719-067-78 8-719-911-19 8-719-058-38 8-719-043-76 DIODE DIODE DIODE DIODE DIODE RG1CLF-B1 RN3Z-LF014-302 1SS119-25 FMN-G12S AK04V0 D621 D626 D627 D628 D629 8-719-068-00 8-719-068-00 8-719-510-26 8-719-059-23 8-719-979-64 DIODE DIODE DIODE DIODE DIODE ERC04-06SE ERC04-06SE D1NL20 P6KE200AG23 UF4005PKG23 D631 D632 D633 8-719-110-31 DIODE RD12ES-B2 8-719-510-64 DIODE S2LA20F 8-719-109-89 DIODE RD5.6ESB2 1-410-397-21 FERRITE 1.1UH 1-410-397-21 FERRITE 1.1UH 1-535-465-11 LEAD, JUMPER (5.0MM) < IC > < SOCKET > J401 J404 1-766-296-11 CONNECTOR, DUAL SCART 1-770-989-11 JACK, PIN 2P < COIL > < FERRITE BEAD > FB001 FB002 FB601 FB602 FB605 1-412-911-11 1-412-911-11 1-412-911-11 1-412-911-11 1-410-397-21 FERRITE FERRITE FERRITE FERRITE FERRITE 0UH 0UH 0UH 0UH 1.1UH FB608 FB609 1-412-911-11 FERRITE 0UH 1-535-465-11 LEAD, JUMPER (5.0MM) 61 L001 L102 L103 L104 L106 1-408-603-31 1-408-599-21 1-403-686-11 1-410-671-31 1-408-417-00 INDUCTOR INDUCTOR COIL INDUCTOR INDUCTOR 10UH 4.7UH L201 L202 L203 L302 L303 1-535 465 11 1-535-465-11 1-406-979-11 1-408-417-00 1-408-609-41 LEAD, JUMPER (5.0MM) LEAD, JUMPER (5.0MM) INDUCTOR 0UH INDUCTOR 47UH INDUCTOR 33UH L401 L402 L405 L406 L501 1-408-417-00 1-408-417-00 1-216-295-00 1-216-295-00 1-408-417-00 INDUCTOR INDUCTOR SHORT SHORT INDUCTOR 47UH 47UH 0 0 47UH L502 L503 L532 L533 L535 1-412-529-11 1-412-521-31 1-412-553-11 1-406-989-21 1-459-111-00 INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR 22UH 4.7UH 3.3MMH 0UH 0UH 47UH 47UH The components identified by shading and marked are critical for safety Replace only with the part number specified. A REF. NO. L537 L540 L571 L602 PART.NO 1-409-756-11 1-409-855-11 1-535 465 11 1-412-533-21 1-408-417-00 DESCRIPTION REMARK COIL, HORIZONTAL LINEARITY COIL, HORIZONTAL LINEARITY LEAD, JUMPER (5.0MM) INDUCTOR 47UH INDUCTOR 47UH REF. NO. (KV-25K5K) (KV-29K5K) < PHOTO COUPLER > PH601 £ 8-749-010-64 PHOTO COUPLER PC123F2 < TRANSISTOR > PART.NO DESCRIPTION REMARK R001 R002 R003 R004 R005 1-216-025-00 1-216-025-00 1-216-065-00 1-216-065-00 1-216-065-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 100 100 4.7K 4.7K 4.7K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R007 R009 R010 R011 R012 1-216-065-00 1-216-025-00 1-216-025-00 1-216-025-00 1-247-807-31 RES,CHIP RES,CHIP RES,CHIP RES,CHIP CARBON 4.7K 100 100 100 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/4W Q004 Q005 Q006 Q007 Q008 8-729-216-22 1-801-806-11 1-801-806-11 8-729-620-06 8-729-620-06 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR 2SA1162-G DTC144EKA DTC144EKA 2SC3052-EF 2SC3052-EF R013 R014 R015 R019 R023 1-216-214-00 1-216-057-00 1-216-049-00 1-216-053-00 1-216-295-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP SHORT 4.7K 2.2K 1K 1.5K 0 5% 5% 5% 5% 1/8W 1/10W 1/10W 1/10W Q009 Q010 Q011 Q012 Q013 8-729-620-06 8-729-620-06 1-801-806-11 8-729-620-06 8-729-620-06 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR 2SC3052-EF 2SC3052-EF DTC144EKA 2SC3052-EF 2SC3052-EF R029 R030 R032 R034 R035 1-216-073-00 1-216-081-00 1-216-089-00 1-216-065-00 1-216-049-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 10K 22K 47K 4.7K 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W Q014 Q101 Q202 Q401 Q405 8-729-120-28 8-729-216-22 8-729-620-06 1-729-920-72 8-729-120-28 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR 2SC1623-L5L6 2SA1162-G 2SC3052-EF 2SA1037K 2SC1623-L5L6 R036 R038 R039 R050 R051 1-216-065-00 1-216-073-00 1-216-089-91 1-216-041-00 1-216-049-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 4.7K 10K 47K 470 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W Q408 Q501 Q532 Q533 Q535 8-729-120-28 8-729-620-06 8-729-038-83 8-729-040-62 8-729-119-80 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR 2SC1623-L5L6 2SC3052-EF 2SK2251-01-F19 2SD2539(LBSONY) 2SC2688-LK R053 R054 R055 R056 R057 1-216-065-00 1-216-041-00 1-216-081-00 1-216-105-00 1-216-075-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 4.7K 470 22K 220K 12K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W Q571 Q574 Q575 Q576 Q601 8-729-105-08 8-729-120-28 1-801-806-11 8-729-120-28 8-729-216-22 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR 2SA1330-O6 2SC1623-L5L6 DTC144EKA 2SC1623-L5L6 2SA1162-G R058 R059 R060 R061 R062 1-216-063-91 1-216-089-00 1-216-174-00 1-216-174-00 1-216-033-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 3.9K 47K 100 100 220 5% 5% 5% 5% 5% 1/10W 1/10W 1/8W 1/8W 1/10W R065 R066 R067 R069 R070 1-216-025-00 1-216-065-00 1-216-065-00 1-216-049-00 1-216-081-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 100 4.7K 4.7K 1K 22K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R071 R072 R073 R075 R077 1-216-214-00 1-216-097-00 1-216-097-00 1-216-069-00 1-216-083-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 4.7K 100K 100K 6.8K 27K 5% 5% 5% 5% 5% 1/8W 1/10W 1/10W 1/10W 1/10W R078 R080 1-216-065-00 RES,CHIP 1-216-073-00 RES,CHIP 4.7K 5% 10K 5% 1/10W 1/10W (KV-29K5K) < RESISTOR > JR023 JR031 JR033 JR403 JR409 1-216-296-00 1-216-295-00 1-216-296-00 1-216-073-00 1-216-295-00 SHORT SHORT SHORT RES,CHIP SHORT 0 0 0 10K 0 JR411 JR412 JR610 JR613 1-216-295-00 1-216-295-00 1-216-296-00 1-216-296-00 SHORT SHORT SHORT SHORT 0 0 0 0 JW220 8-719-109-89 DIODE 5% (KV-29K5K) 1/10W RDS.6ESB2 62 (KV-29K5K) The components identified by shading and marked are critical for safety Replace only with the part number specified. REF. NO. PART.NO A DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK R081 R082 R083 R084 R085 1-216-073-00 1-216-053-00 1-216-031-00 1-216-053-00 1-216-031-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 10K 1.5K 180 1.5K 180 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R313 R314 R315 R316 R317 1-216-025-00 1-216-025-00 1-216-075-91 1-216-025-00 1-216-049-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 100 100 12K 100 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R086 R087 R088 R089 R090 1-216-053-00 1-216-180-00 1-216-065-00 1-216-081-00 1-216-057-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 1.5K 180 4.7K 22K 2.2K 5% 5% 5% 5% 5% 1/10W 1/8W 1/10W 1/10W 1/10W R318 R319 R320 R321 R323 1-216-025-00 1-216-025-00 1-216-025-00 1-216-025-00 1-216-025-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 100 100 100 100 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R091 R092 R093 R094 R095 1-216-081-00 1-216-073-00 1-216-230-00 1-216-057-00 1-216-025-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 22K 10K 22K 2.2K 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/8W 1/10W 1/10W R324 R325 R326 R327 R331 1-412-002-21 1-412-002-21 1-216-129-00 1-216-295-00 1-216-057-00 INDUCTOR INDUCTOR RES,CHIP SHORT RES,CHIP 4.7UH 4.7UH 2.2M 5% 0 2.2K 5% 1/10W R096 R097 R098 R099 R101 1-247-807-31 1-247-807-31 1-247-807-31 1-247-807-31 1-216-049-00 CARBON CARBON CARBON CARBON RES,CHIP 100 100 100 100 1K 5% 5% 5% 5% 5% 1/4W 1/4W 1/4W 1/4W 1/10W R332 R333 R334 R335 R337 1-216-057-00 1-216-057-00 1-216-025-00 1-216-025-00 1-216-065-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 2.2K 2.2K 100 100 4.7K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R106 R116 R120 R121 R122 1-215-900-11 1-249-437-11 1-216-037-00 1-216-025-00 1-216-025-00 METAL OXIDE CARBON RES,CHIP RES,CHIP RES,CHIP 22K 47K 330 100 100 5% 5% 5% 5% 5% 2W F 1/4W 1/10W 1/10W 1/10W R338 R401 R402 R403 R404 1-216-049-00 1-216-113-00 1-216-295-71 1-216-041-00 1-216-113-00 RES,CHIP 1K RES,CHIP 470K CONDUCTER CHIP RES,CHIP 470 RES,CHIP 470K 5% 5% 1/10W 1/10W 5% 5% 1/10W 1/10W R133 R142 R143 R144 R145 1-216-295-00 1-216-295-00 1-216-025-00 1-216-079-00 1-216-212-00 SHORT SHORT RES,CHIP RES,CHIP RES,CHIP 0 0 100 5% 18K 5% 3.9K 5% 1/10W 1/10W 1/8W R405 R406 R408 R409 R410 1-216-295-00 1-216-113-00 1-216-022-00 1-216-029-00 1-216-029-00 SHORT RES,CHIP RES,CHIP RES,CHIP RES,CHIP 0 470K 75 150 150 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W R151 R154 R155 R204 R206 1-216-049-00 1-216-238-91 1-216-089-00 1-247-863-91 1-216-085-00 RES,CHIP RES,CHIP RES,CHIP CARBON RES,CHIP 1K 47K 47K 22K 33K 5% 5% 5% 5% 5% 1/10W 1/8W 1/10W 1/4W 1/10W R411 R412 R413 R414 R415 1-216-022-00 1-216-029-00 1-216-295-00 1-216-022-00 1-216-022-00 RES,CHIP RES,CHIP SHORT RES,CHIP RES,CHIP 75 150 0 75 75 5% 5% 1/10W 1/10W 5% 5% 1/10W 1/10W R207 R209 R211 R213 R301 1-216-295-00 1-216-065-00 1-215-873-00 1-216-089-00 1-216-025-00 SHORT RES,CHIP METAL OXIDE RES,CHIP RES,CHIP 0 4.7K 4.7K 47K 100 5% 5% 5% 5% 1/10W 1W F 1/10W 1/10W R417 R418 R419 R420 R421 1-260-158-11 1-247-823-31 1-216-022-00 1-216-041-00 1-216-113-00 CARBON CARBON RES,CHIP RES,CHIP RES,CHIP 75 470 75 470 470K 5% 5% 5% 5% 5% 1/2W 1/4W 1/10W 1/10W 1/10W R302 R303 R304 R306 R309 1-216-081-00 1-216-073-00 1-216-073-00 1-216-206-00 1-216-675-11 RES,CHIP RES,CHIP RES,CHIP RES,CHIP METAL CHIP 22K 10K 10K 2.2K 10K 5% 5% 5% 5% 0.50% 1/10W 1/10W 1/10W 1/8W 1/10W R422 R425 R426 R427 R429 1-216-295-00 1-216-077-00 1-216-073-00 1-216-113-00 1-216-041-00 SHORT RES,CHIP RES,CHIP RES,CHIP RES,CHIP 0 15K 10K 470K 470 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W R310 R311 1-216-022-00 RES,CHIP 1-216-022-00 RES,CHIP 75 75 5% 5% 1/10W 1/10W R430 R431 1-216-113-00 RES,CHIP 1-216-295-00 SHORT 470K 5% 0 1/10W (KV-29K5K) (KV-29K5K) (KV-29K5K) (KV-29K5K) 63 1/10W The components identified by shading and marked are critical for safety Replace only with the part number specified. A REF. NO. PART.NO DESCRIPTION REMARK REF. NO. R432 R435 R436 R439 R440 1-216-113-00 1-216-022-00 1-216-041-00 1-216-041-00 1-216-113-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 470K 75 470 470 470K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R441 R442 R443 R450 R454 1-216-295-00 1-216-077-00 1-216-073-00 1-216-041-00 1-216-041-00 SHORT RES,CHIP RES,CHIP RES,CHIP RES,CHIP 0 15K 10K 470 470 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W R457 R459 R460 R501 R502 1-216-025-00 1-247-807-31 1-249-403-11 1-216-081-00 1-216-097-00 RES,CHIP CARBON CARBON RES,CHIP RES,CHIP 100 100 68 22K 100K 5% 5% 5% 5% 5% 1/10W 1/4W 1/4W 1/10W 1/10W R546 R503 R504 R505 R506 R507 1-215-888-00 1-249-385-11 1-216-065-00 1-216-061-00 1-216-349-00 METAL OXIDE CARBON RES,CHIP RES,CHIP METAL OXIDE 220 2.2 4.7K 3.3K 1 5% 5% 5% 5% 5% R508 R509 R510 R511 R512 1-216-065-00 1-216-061-00 1-216-081-00 1-215-869-11 1-249-377-11 RES,CHIP RES,CHIP RES,CHIP METAL OXIDE CARBON 4.7K 3.3K 22K 1K 0.47 R513 R514 R515 R516 1-216-097-00 1-249-377-11 1-249-377-11 1-249-493-11 RES,CHIP CARBON CARBON CARBON R517 1-249-434-11 1-249-429-11 1-216-065-00 1-215-884-11 DESCRIPTION REMARK 1-216-107-00 1-216-113-91 1-216-109-00 1-216-101-00 1-216-049-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 220K 470K 330K 150K 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W 1-215-861-00 1-216-095-00 1-216-097-00 1-216-089-00 1-216-089-00 METAL OXIDE RES,CHIP RES,CHIP RES,CHIP RES,CHIP 47 82K 100K 47K 47K 5% 5% 5% 5% 5% 1W F 1/10W (KV-25K5K) 1/10W (KV-29K5K) 1/10W 1/10W METAL OXIDE 47 5% METAL OXIDE 1.5K 5% LEAD JUMPER (7.5MM) METAL OXIDE 1.5K 5% METAL OXIDE 4.7 5% 2W 2W R548 1-249-401-11 1-215-893-11 1-535-143-71 1-215-893-11 1-216-397-11 2W F 1/4W F 1/10W 1/10W 1W F R549 R551 R552 R553 R571 1-216-341-11 1-215-873-21 1-216-061-00 1-249-381-11 1-249-417-11 METAL OXIDE 0.22 5% METAL OXIDE 4.7K 5% RES,CHIP 3.3K 5% CARBON 1 5% CARBON 1K 5% 1W F 1W F 1/10W 1/4W F 1/4W F 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1W F 1/4W F R572 R573 R574 R575 1-216-369-00 1-216-101-00 1-216-097-00 1-216-065-00 1-216-097-00 METAL OXIDE RES,CHIP RES,CHIP RES,CHIP RES,CHIP 1 150K 100K 4.7K 100K 2W F 1/10W (KV-25K5K) 1/10W (KV-29K5K) 1/10W 1/10W 100K 0.47 0.47 56K 5% 5% 5% 5% 1/10W 1/4W F 1/4W F 1/2W R576 R581 R582 R583 R588 1-408-599-31 1-216-089-00 1-216-089-00 1-216-081-00 1-216-053-00 INDUCTOR RES,CHIP RES,CHIP RES,CHIP RES,CHIP 4.7UH 47K 5% 47K 5% 22K 5% 1.5K 5% 1/10W 1/10W 1/10W 1/10W CARBON CARBON RES,CHIP METAL OXIDE 27K 10K 4.7K 47 5% 5% 5% 5% 1/4W (KV-25K5K) 1/4W (KV-29K5K) 1/10W 2W F RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 680K 1M 100K 1M 27K 5% 5% 5% 5% 5% 1/10W (KV-25K5K) 1/10W (KV-29K5K) 1/10W 1/10W 1/10W 1-216-097-00 1-216-081-00 1-217-778-77 1-249-439-11 1-216-057-00 RES,CHIP RES,CHIP FUSIBLE CARBON RES,CHIP 100K 22K 1K 68K 2.2K 5% 5% 5% 5% 5% 1/10W 1/10W 1W F 1/4W 1/10W R522 R523 R524 1-216-117-00 1-208-845-11 1-216-097-00 1-208-845-11 1-216-083-00 R589 R590 R591 R593 R594 R525 R526 R527 R528 R529 1-216-057-00 1-216-089-00 1-216-077-00 1-216-246-00 1-216-073-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 2.2K 47K 15K 100K 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/8W 1/10W R602 1-202-961-11 CEMENTED R603 1-202-933-61 FUSIBLE R607 £ 1-202-961-11 CEMENTED R608 1-215-927-00 METAL OXIDE R611 1-249-415-11 CARBON 1.8 0.1 1.8 47K 680 5% 10W 10% 1/2W F 5% 10W 5% 3W F 5% 1/4W R530 R531 R532 R533 1-216-085-00 1-216-057-00 1-216-063-91 1-216-073-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP 33K 2.2K 3.9K 10K 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W R613 £ 1-240-030-91 METAL R614 £ 1-240-030-91 METAL R615 1-249-422-11 CARBON R616 1-216-393-00 METAL OXIDE R617 1-249-405-11 CARBON 4.7M 4.7M 2.7K 2.2 100 5% 5% 5% 5% 5% R619 4.7K 5% R518 R520 R521 R534 PART.NO R535 R539 R540 R541 R542 R543 R547 64 1-216-065-00 RES,CHIP 5% 5% 5% 5% 5% 2W 3W (KV-25K5K) (KV-29K5K) (KV-25K5K) (KV-29K5K) F (KV-25K5K) F (KV-29K5K) (KV-25K5K) F (KV-29K5K) F 1/2W 1/2W 1/4W 3W F 1/4W F 1/10W The components identified by shading and marked are critical for safety Replace only with the part number specified. REF. NO. PART.NO A DESCRIPTION REMARK R622 R627 R628 R652 R653 1-249-401-11 1-249-389-11 1-247-791-91 1-216-393-00 1-216-393-00 CARBON CARBON CARBON METAL OXIDE METAL OXIDE 47 4.7 22 2.2 2.2 5% 5% 5% 5% 5% 1/4W 1/4W F 1/4W 3W F 3W F R658 R659 R660 R661 R662 1-215-929-11 1-216-383-21 1-216-384-21 1-247-843-11 1-215-929-11 METAL OXIDE METAL OXIDE METAL OXIDE CARBON METAL OXIDE 100K 0.33 0.39 3.3K 100K 5% 5% 5% 5% 5% 3W 3W 3W 1/4W 3W R664 R665 R667 R900 1-249-417-11 1-215-877-11 1-215-927-00 1-249-429-11 CARBON METAL OXIDE METAL OXIDE CARBON 1K 22K 47K 10K 5% 5% 5% 5% 1/4W 1W F 3W F 1/4W REF. NO. F F F C701 C702 C703 C708 C710 1-102-114-00 1-102-115-00 1-102-116-00 1-162-114-00 1-107-652-11 CERAMIC CERAMIC CERAMIC CERAMIC ELECT 470PF 560PF 680PF 0.0047MF 10MF 10% 10% 10% 20% 50V 50V 50V 2KV 250V C712 C714 C717 C718 C719 1-102-116-00 1-126-967-11 1-102-114-00 1-102-114-00 1-102-114-00 CERAMIC ELECT CERAMIC CERAMIC CERAMIC 680PF 47MF 470PF 470PF 470PF 10% 20% 10% 10% 10% 50V 16V 50V 50V 50V C722 C723 C724 1-101-880-00 CERAMIC 1-101-880-00 CERAMIC 1-101-880-00 CERAMIC 47PF 47PF 47PF 5% 5% 5% 50V 50V 50V 5% 1W F < SWITCH > < CONNECTOR > 1-572-707-11 SWITCH, LEVER CN701 CN702 CN703 < TRANSFORMER > T531 £ 1-453-264-11 TRANSFORMER ASSY, FLYBACK (NX-1680/U2B4) (KV-25K5K) 1-453-265-11 TRANSFORMER ASSY, FLYBACK (NX-1681/U2B4) (KV-29K5K) 1-437-195-11 TRANSFORMER, HORIZONTAL DRIVE T532 T601 T602 T603 1-431-228-11 £ 1-427-962-11 1-431-732-11 £ 1-431-777-11 TRANSFORMER, TRANSFORMER, TRANSFORMER, TRANSFORMER, REMARK < CAPACITOR > RY601 £ 1-755-245-11 RELAY T511 DESCRIPTION *A-1638-112-A C BOARD, COMPLETE ***************** < RELAY > SW532 PART.NO 1-784-633-11 PIN, CONNECTOR 4P 1-695-915-11 TAB (CONTACT) *1-564-509-11 PLUG, CONNECTOR 6P < DIODE > POWER MODULATION LINE FILTER CONVERTER (SRT) CONVERTER < THERMISTOR > D702 D703 D704 D705 D706 8-719-991-33 1-535-465-11 1-535-465-11 1-535-465-11 8-719-991-33 DIODE DIODE DIODE DIODE DIODE 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 D707 D708 D709 D710 D711 8-719-991-33 8-719-991-33 8-719-991-33 8-719-991-33 1-216-549-51 DIODE DIODE DIODE DIODE LEAD, 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 RES, FILM 1 D714 D715 D716 D717 D718 8-719-991-33 8-719-991-33 8-719-991-33 8-719-991-33 8-719-991-33 DIODE DIODE DIODE DIODE DIODE 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 D719 8-719-991-33 DIODE 1SS133T-77 THP601 £ 1-810-961-11 THERMISTOR, POSITIVE < TUNER > TU101 8-598-432-00 TUNER (FSS BTP-AC411) < CRYSTAL > X001 X302 X303 1-578-774-11 VIBRATOR, CRYSTAL 1-567-505-11 OSCILLATOR, CRYSTAL 1-567-504-11 OSCILLATOR, CRYSTAL < CRT SOCKET > J701 £ 1-526-990-21 SOCKET, CRT < COIL > L704 65 1-408-609-41 INDUCTOR 33UH C C VM REF. NO. PART.NO The components identified by shading and marked are critical for safety Replace only with the part number specified. DESCRIPTION REMARK REF. NO. < TRANSISTOR > R745 R746 Q702 Q703 Q704 Q705 Q706 8-729-119-78 8-729-906-70 8-729-200-17 8-729-119-78 8-729-906-70 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR 2SC2785-HFE BF871-127 BF421L-AMMO 2SC2785-HFE BF871-127 Q707 Q708 Q709 Q710 8-729-200-17 8-729-119-78 8-729-906-70 8-729-200-17 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR BF421L-AMMO 2SC2785-HFE BF871-127 BF421L-AMMO PART.NO DESCRIPTION 1-249-421-11 CARBON 1-249-421-11 CARBON REMARK 2.2K 5% 2.2K 5% 1/4W 1/4W < VARIABLE RESISTOR > RV701 RV702 1-230-641-11 RES, ADJ, METAL GLAZE 2.2M 1-241-656-21 RES, ADJ, METAL FILM 110M ********************************************************************* *A-1644-093-A VM BOARD, COMPLETE (KV-29K5 ONLY) ****************** < RESISTOR > < CAPACITOR > R701 R704 R705 R706 R707 1-247-895-91 1-216-486-00 1-260-103-11 1-247-815-91 1-247-815-91 CARBON METAL OXIDE CARBON CARBON CARBON 470K 8.2K 2.2K 220 220 5% 5% 5% 5% 5% 1/4W 3W F 1/2W 1/4W 1/4W R708 R709 R711 R712 R713 1-247-791-91 1-202-844-00 1-247-843-11 1-260-103-11 1-247-875-91 CARBON SOLID CARBON CARBON CARBON 22 330K 3.3K 2.2K 68K 5% 10% 5% 5% 5% 1/4W 1/2W 1/4W 1/2W 1/4W R714 R715 R716 R717 R718 1-216-486-00 1-249-417-11 1-247-815-91 1-247-815-91 1-202-814-11 METAL OXIDE CARBON CARBON CARBON SOLID 8.2K 1K 220 220 33K 5% 5% 5% 5% 10% 3W F 1/4W 1/4W 1/4W 1/2W R719 R720 R722 R723 R724 1-247-791-91 1-247-843-11 1-202-848-00 1-249-417-11 1-260-131-11 CARBON CARBON SOLID CARBON CARBON 22 3.3K 680K 1K 470K 5% 5% 10% 5% 5% 1/4W 1/4W 1/2W 1/4W 1/2W R726 R727 R728 R729 R730 1-260-103-11 1-247-815-91 1-216-351-00 1-247-815-91 1-247-791-91 CARBON CARBON METAL OXIDE CARBON CARBON 2.2K 220 1.5 220 22 5% 5% 5% 5% 5% 1/2W 1/4W 1W F 1/4W 1/4W R731 R733 R734 R735 R736 1-247-843-11 1-247-823-91 1-247-807-31 1-247-823-91 1-216-486-00 CARBON CARBON CARBON CARBON METAL OXIDE 3.3K 470 100 470 8.2K 5% 5% 5% 5% 5% 1/4W 1/4W 1/4W 1/4W 3W F R737 R739 R740 R741 R744 1-247-891-91 1-249-417-11 1-247-823-91 1-202-549-00 1-249-421-11 CARBON CARBON CARBON SOLID CARBON 330K 1K 470 100 2.2K 5% 5% 5% 20% 5% 1/4W 1/4W 1/4W 1/2W 1/4W 66 C1701 C1702 C1703 C1704 C1705 1-126-933-11 1-128-551-11 1-126-933-11 1-107-357-11 1-107-638-11 ELECT ELECT ELECT FILM ELECT 100MF 22MF 100MF 0.47MF 33MF 20% 20% 20% 5% 20% 16V 25V 16V 100V 160V C1706 C1707 C1708 C1709 C1710 1-104-999-11 1-136-207-11 1-137-364-11 1-137-364-11 1-163-009-11 FILM FILM FILM FILM CERAMIC CHIP 0.1MF 0.047MF 0.001MF 0.001MF 0.001MF 5% 10% 5% 5% 10% 200V 250V 50V 50V 50V C1720 C1721 C1722 C1723 C1725 1-107-667-11 1-136-207-11 1-126-934-11 1-161-830-00 1-535-465-11 ELECT FILM ELECT CERAMIC LEAD, JUMPER 2.2MF 0.047MF 220MF 0.0047MF (5.0MM) 20% 10% 20% 160V 250V 16V 500V C1726 C1803 C1804 C1805 C1841 1-126-934-11 1-163-037-11 1-126-964-11 1-137-366-11 1-163-023-00 ELECT 220MF CERAMIC CHIP 0.022MF ELECT 10MF FILM 0.0022MF CERAMIC CHIP 0.015MF 20% 10% 20% 5% 10% 16V 50V 50V 50V 50V C1844 C1845 C1901 C1902 C1903 1-130-959-00 1-136-175-00 1-163-251-11 1-137-374-11 1-126-964-11 FILM 0.047MF FILM 0.68MF CERAMIC CHIP 100PF FILM 0.047MF ELECT 10MF 10% 5% 5% 5% 20% 400V 50V 50V 50V 50V C1904 C1905 C1906 C1911 C1912 1-137-366-11 1-137-374-11 1-164-232-11 1-136-189-00 1-129-702-00 FILM 0.0022MF FILM 0.047MF CERAMIC CHIP 0.01MF FILM 0.1MF FILM 0.001MF 5% 5% 10% 10% 5% 50V 50V 50V 250V 630V C1913 C1914 C1915 C1951 1-136-558-11 1-102-157-00 1-137-102-11 1-126-964-11 FILM CERAMIC FILM ELECT 5% 10% 10% 20% 630V 500V 250V 50V 0.0039MF 560PF 0.022MF 10MF The components identified by shading and marked are critical for safety Replace only with the part number specified. REF. NO. PART.NO VM DESCRIPTION REMARK REF. NO. L1901 C1952 C1953 C1954 C1955 C1956 1-164-232-11 1-136-165-00 1-164-232-11 1-136-165-00 1-126-964-11 CERAMIC CHIP 0.01MF FILM 0.1MF CERAMIC CHIP 0.01MF FILM 0.1MF ELECT 10MF 10% 5% 10% 5% 20% 50V 50V 50V 50V 50V C1957 C1958 C1959 C1960 1-126-964-11 1-136-173-00 1-107-714-11 1-107-636-11 ELECT FILM ELECT ELECT 20% 5% 20% 20% 50V 50V 50V 160V 10MF 0.47MF 10MF 10MF *1-564-510-11 1-774-418-11 *1-564-506-11 1-564-507-71 1-508-784-12 DESCRIPTION 1-406-677-11 INDUCTOR REMARK 0UH < TRANSISTOR > < CONNECTOR > CN1705 CN1718 CN1801 CN1803 CN1809 PART.NO PLUG, CONNECTOR 7P CONNECTOR, BOARD TO BOARD 8P PLUG, CONNECTOR 3P PIN, CONNECTOR 4P PIN, CONNECTOR 5MM PITCH 1P < DIODE > Q1701 Q1702 Q1703 Q1704 Q1706 8-729-120-28 8-729-120-28 8-729-017-05 8-729-119-78 8-729-017-06 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR 2SC1623-L5L6 2SC1623-L5L6 2SA1837 2SC2785-HFE 2SC4793 Q1708 Q1709 Q1710 Q1840 Q1841 8-729-216-22 8-729-120-28 8-729-620-06 8-729-120-28 8-729-931-45 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR 2SA1162-G 2SC1623-L5L6 2SC3052-EF 2SC2412K-T-146-QR IRF614-LF Q1901 Q1902 Q1903 Q1904 Q1905 8-729-620-06 8-729-620-06 8-729-043-95 8-729-620-06 8-729-620-06 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR 2SC3052-EF 2SC3052-EF 2SC3840(3) 2SC3052-EF 2SC3052-EF Q1906 Q1907 8-729-119-80 TRANSISTOR 2SC2688-LK 8-729-119-80 TRANSISTOR 2SC2688-LK D1701 D1702 D1703 D1801 D1802 8-719-991-33 8-719-110-88 8-719-110-88 8-719-110-17 8-719-110-17 DIODE DIODE DIODE DIODE DIODE 1SS133T-77 RD39ES-B2 RD39ES-B2 RD10ESB2 RD10ESB2 D1803 D1840 D1841 D1901 D1902 8-719-110-17 8-719-302-43 8-719-991-33 8-719-991-33 8-719-991-33 DIODE DIODE DIODE DIODE DIODE RD10ESB2 EL1Z 1SS133T-77 1SS133T-77 1SS133T-77 R1701 R1702 R1703 R1704 R1705 1-216-049-00 1-216-049-00 1-216-057-00 1-216-045-00 1-247-815-91 RES,CHIP RES,CHIP RES,CHIP RES,CHIP CARBON 1K 1K 2.2K 680 220 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/4W D1903 D1904 D1905 D1906 D1907 8-719-991-33 8-719-991-33 8-719-923-60 8-719-970-87 8-719-970-87 DIODE DIODE DIODE DIODE DIODE 1SS133T-77 1SS133T-77 MTZJ-T-77-9.1A ERA38-06 ERA38-06 R1706 R1708 R1712 R1713 R1714 1-247-815-91 1-216-035-00 1-260-311-11 1-249-384-11 1-249-414-11 CARBON RES,CHIP CARBON CARBON CARBON 220 270 39 1.8 560 5% 5% 5% 5% 5% 1/4W 1/10W 1/2W 1/4W F 1/4W F D1908 D1909 D1910 8-719-300-33 DIODE RU-3AM 8-719-991-33 DIODE 1SS133T-77 8-719-991-33 DIODE 1SS133T-77 R1715 R1716 R1717 R1718 R1719 1-249-432-11 1-249-417-11 1-215-913-11 1-249-432-11 1-249-384-11 CARBON CARBON METAL OXIDE CARBON CARBON 18K 1K 220 18K 1.8 5% 5% 5% 5% 5% 1/4W 1/4W F 3W F 1/4W 1/4W F R1720 R1721 R1722 R1724 R1725 1-249-400-11 1-249-414-11 1-216-017-91 1-216-017-91 1-215-887-00 CARBON CARBON RES,CHIP RES,CHIP METAL OXIDE 39 560 47 47 150 5% 5% 5% 5% 5% 1/4W F 1/4W 1/10W 1/10W 2W F R1728 R1729 R1730 R1731 R1751 1-216-037-00 1-216-041-00 1-216-059-00 1-249-411-11 1-216-049-71 RES,CHIP RES,CHIP RES,CHIP CARBON RES,CHIP 330 470 2.7K 330 1K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/4W 1/10W < RESISTOR > < IC > IC1801 IC1901 IC1902 8-759-603-37 IC M5216P 8-759-450-95 IC LM393N 8-759-008-70 IC LM358N < COIL > L1701 L1702 L1703 L1841 L1843 1-408-603-31 1-408-597-31 1-408-603-31 1-406-674-11 1-406-989-21 INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR 10UH 3.3UH 10UH 0UH 0UH 67 VM REF. NO. The components identified by shading and marked are critical for safety Replace only with the part number specified. H1 PART.NO DESCRIPTION REMARK REF. NO. PART.NO DESCRIPTION REMARK R1752 R1753 R1805 R1806 R1807 1-216-049-71 1-216-049-71 1-216-073-00 1-216-117-00 1-216-073-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 1K 1K 10K 680K 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1961 R1962 R1963 R1964 R1965 1-216-097-00 1-216-101-00 1-216-081-00 1-216-057-00 1-216-081-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 100K 150K 22K 2.2K 22K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1808 R1809 R1810 R1841 R1842 1-216-073-00 1-216-073-00 1-216-073-00 1-216-097-00 1-216-057-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 10K 10K 10K 100K 2.2K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1966 R1967 R1968 R1969 1-216-081-00 1-215-876-00 1-249-416-11 1-215-870-11 RES,CHIP METAL OXIDE CARBON METAL OXIDE 22K 15K 820 1.5K 5% 5% 5% 5% 1/10W 1W F 1/4W 1W F R1843 R1844 R1846 R1847 R1848 1-260-111-11 1-216-061-00 1-260-111-11 1-215-886-11 1-215-875-11 CARBON RES,CHIP CARBON METAL OXIDE METAL OXIDE 10K 3.3K 10K 100 10K 5% 5% 5% 5% 5% 1/2W 1/10W 1/2W 2W F 1W F R1901 R1902 R1903 R1904 R1905 1-249-441-11 1-216-073-00 1-216-073-00 1-216-073-00 1-216-097-00 CARBON RES,CHIP RES,CHIP RES,CHIP RES,CHIP 100K 10K 10K 10K 100K 5% 5% 5% 5% 5% 1/4W 1/10W 1/10W 1/10W 1/10W R1906 R1907 R1908 R1909 R1910 1-216-073-00 1-216-097-00 1-216-033-00 1-215-493-00 1-216-295-00 RES,CHIP RES,CHIP RES,CHIP METAL SHORT 10K 100K 220 1M 0 5% 5% 5% 1% 1/10W 1/10W 1/10W 1/4W R1911 R1912 R1913 R1914 R1915 1-216-073-00 1-216-121-91 1-216-049-00 1-216-057-00 1-216-073-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 10K 1M 1K 2.2K 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1916 R1917 R1921 R1922 R1923 1-216-675-11 1-216-687-11 1-215-896-51 1-215-878-00 1-216-097-00 METAL CHIP METAL CHIP METAL OXIDE METAL OXIDE RES,CHIP 10K 33K 4.7K 33K 100K 0.50% 0.50% 5% 5% 5% 1/10W 1/10W 2W F 1W F 1/10W R1924 R1925 R1951 R1952 R1953 1-216-097-00 1-216-097-00 1-216-073-00 1-216-065-00 1-216-081-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 100K 100K 10K 4.7K 22K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1954 R1955 R1956 R1957 R1958 1-216-097-00 1-216-089-00 1-216-113-00 1-216-073-00 1-216-065-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 100K 47K 470K 10K 4.7K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1959 R1960 1-216-065-00 RES,CHIP 1-216-113-00 RES,CHIP 4.7K 5% 470K 5% 1/10W 1/10W < TRANSFORMER > T1901 1-424-584-11 TRANSFORMER, DYNAMIC FOCUS ********************************************************************* *A-1646-160-A H1 BOARD, COMPLETE ******************* < CAPACITOR > C902 C903 C904 C905 C907 1-137-372-11 1-137-372-11 1-104-665-11 1-126-964-11 1-126-960-11 FILM FILM ELECT ELECT ELECT C908 C911 C912 1-126-960-11 ELECT 1-102-074-00 CERAMIC 1-102-074-00 CERAMIC 0.022MF 0.022MF 100MF 10MF 1MF 5% 5% 20% 20% 20% 50V 50V 25V 50V 50V 1MF 0.001MF 0.001MF 20% 10% 10% 50V 50V 50V < CONNECTOR > CN603 £ *1-580-844-11 PIN, CONNECTOR (POWER) CN604 £ *1-695-292-11 PIN, CONNECTOR (POWER) CN900 1-779-947-11 TERMINAL BLOCK S CN906 *1-564-511-11 PLUG, CONNECTOR 8P CN907 *1-564-510-11 PLUG, CONNECTOR 7P CN908 *1-564-508-11 PLUG, CONNECTOR 5P < DIODE > D901 68 D902 D903 D904 8-719-302-45 4-203-258-01 8-719-929-15 8-719-929-15 8-719-109-97 DIODE SEL1210S-D HOLDER LED (D901) DIODE HZS9.INBZ DIODE HZS9.INBZ DIODE RD6.8ES-B2 D905 D906 D907 D908 8-719-109-97 8-719-923-60 8-719-923-60 8-719-923-60 DIODE DIODE DIODE DIODE RD6.8ES-B2 MTZJ-T-77-9.1A MTZJ-T-77-9.1A MTZJ-T-77-9.1A The components identified by shading and marked are critical for safety Replace only with the part number specified. REF. NO. PART.NO H1 DESCRIPTION REMARK REF. NO. < FUSE > F601 £ 1-576-232-21 FUSE (H.B.C.) 5AMP 250V £ 1-535-725-11 FUSE HOLDER (F601) PART.NO DESCRIPTION S1 REMARK C1112 C1113 C1114 C1115 C1118 1-163-001-11 1-104-664-11 1-163-001-11 1-104-664-11 1-162-637-11 CERAMIC CHIP 220PF ELECT 47MF CERAMIC CHIP 220PF ELECT 47MF CERAMIC CHIP 0.47MF 10% 20% 10% 20% 50V 25V 50V 25V 16V C1120 C1122 C1123 C1124 C1127 1-164-005-11 1-104-664-11 1-164-004-11 1-163-251-11 1-163-239-11 CERAMIC ELECT CERAMIC CERAMIC CERAMIC CHIP 0.47MF 47MF CHIP 0.1MF CHIP 100PF CHIP 33PF 20% 10% 5% 5% 25V 25V 25V 50V 50V C1128 C1129 C1130 C1132 C1133 1-163-239-11 1-163-989-11 1-110-501-11 1-104-664-11 1-164-004-11 CERAMIC CERAMIC CERAMIC ELECT CERAMIC CHIP 33PF CHIP 0.033MF CHIP 0.33MF 47MF CHIP 0.1MF 5% 10% 10% 20% 10% 50V 25V 16V 25V 25V C1143 C1144 C1145 C1146 C1147 1-163-005-11 1-163-005-11 1-163-077-00 1-164-005-11 1-164-005-11 CERAMIC CERAMIC CERAMIC CERAMIC CERAMIC CHIP CHIP CHIP CHIP CHIP 10% 10% 10% 50V 50V 25V 25V 25V C1148 C1149 C1150 C1151 C1152 1-164-005-11 1-126-963-11 1-126-963-11 1-104-664-11 1-164-004-11 CERAMIC CHIP 0.47MF ELECT 4.7MF ELECT 4.7MF ELECT 47MF CERAMIC CHIP 0.1MF < IC > IC900 8-742-014-11 HYB IC SBX1981-51 < SOCKET > J900 1-764-606-11 JACK < COIL > L900 L901 L902 L903 1-412-531-31 1-412-531-31 1-408-603-31 1-408-603-31 INDUCTOR INDUCTOR INDUCTOR INDUCTOR 33UH 33UH 10UH 10UH < RESISTOR > R900 R901 R902 R903 R904 1-247-807-31 1-249-426-11 1-249-437-11 1-260-091-11 1-260-091-11 CARBON CARBON CARBON CARBON CARBON 100 5.6K 47K 220 220 R908 R909 R910 R911 R912 1-249-401-11 1-247-895-91 1-247-895-91 1-535-465-11 1-249-422-11 CARBON CARBON CARBON LEAD, JUMPER CARBON R913 R914 1-249-429-11 CARBON 1-247-863-91 CARBON 5% 5% 5% 5% 5% 1/4W 1/4W 1/4W 1/2W 1/2W 47 5% 470K 5% 470K 5% (5.0MM) 2.7K 5% 1/4W 1/4W 1/4W 10K 22K 5% 5% 470PF 470PF 0.1MF 0.47MF 0.47MF < CONNECTOR > 1/4W CN1101 1/4W 1/4W 1-766-925-11 CONNECTOR, BOARD TO BOARD 18P < DIODE > D1101 8-719-066-72 DIODE BB135 < SWITCH > < FERRITE BEAD > S601 S900 S901 S902 £ 1-571-433-21 1-692-979-21 1-692-979-21 1-692-979-21 SWITCH, SWITCH, SWITCH, SWITCH, PUSH (AC POWER) TACTILE TACTILE TACTILE ********************************************************************* *A-1652-054-A S1 BOARD,COMPLETE ***************** FB1101 FB1102 FB1103 FB1104 FB1105 1-410-396-41 1-410-396-41 1-410-396-41 1-410-396-41 1-410-396-41 FERRITE FERRITE FERRITE FERRITE FERRITE 0.45UH 0.45UH 0.45UH 0.45UH 0.45UH FB1110 FB1111 FB1112 1-412-002-31 INDUCTOR CHIP 4.7UH 1-412-002-31 INDUCTOR CHIP 4.7UH 1-412-002-31 INDUCTOR CHIP 4.7UH < CAPACITOR > < IC > C1103 C1106 C1107 C1108 C1109 1-164-232-11 1-164-232-11 1-164-232-11 1-164-232-11 1-104-664-11 CERAMIC CERAMIC CERAMIC CERAMIC ELECT CHIP CHIP CHIP CHIP 0.01MF 0.01MF 0.01MF 0.01MF 47MF 10% 10% 10% 10% 20% 20% 20% 20% 10% 50V 50V 50V 50V 25V IC1101 IC1102 IC1103 69 8-759-466-48 IC TDA9875P 8-759-100-96 IC UPC4558G2 8-759-394-57 IC PST593C-MMP-4P 25V 50V 50V 25V 25V The components identified by shading and marked are critical for safety Replace only with the part number specified. S1 REF. NO. PART.NO DESCRIPTION REMARK REF. NO. PART.NO < COIL > L1101 L1114 L1115 L1116 1-408-596-31 1-410-671-31 1-408-599-31 1-408-599-31 REMARK MISCELLANEOUS ************** INDUCTOR INDUCTOR INDUCTOR INDUCTOR 2.7UH 47UH 4.7UH 4.7UH £ 1-416-465-11 COIL, DEMAGNETIZATION (KV-25K5K) £ 1-416-654-11 COIL, DEMAGNETIZATION (KV-29K5K) 1-452-032-00 MAGNET, DISC; 10MM Ø 1-452-094-00 MAGNET, ROTATABLE DISC; 15MM Ø £ 8-453-005-21 NECK ASSY (NA297-M2) (KV-29K5K) < RESISTOR > JR1105 JR1112 JR1113 1-216-295-00 SHORT 0 1-216-295-71 CONDUCTOR CHIP 1-216-295-71 CONDUCTOR CHIP R1101 R1102 R1103 R1105 R1110 1-216-073-00 1-216-073-00 1-216-035-00 1-216-035-00 1-216-025-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 10K 10K 270 270 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1111 R1113 R1116 R1117 R1118 1-216-025-00 1-216-073-00 1-216-689-11 1-216-073-00 1-216-682-11 RES,CHIP RES,CHIP METAL CHIP RES,CHIP METAL CHIP 100 10K 39K. 10K 20K 5% 5% 50% 5% 0.50% 1/10W 1/10W 1/10W 1/10W 1/10W R1121 R1122 R1123 R1124 R1125 1-216-065-71 1-216-065-71 1-216-065-71 1-216-073-71 1-216-065-71 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 4.7K 4.7K 4.7K 10K 4.7K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1126 R1164 R1174 R1175 R1176 1-216-073-71 1-216-073-00 1-216-085-00 1-216-085-00 1-216-085-00 RES,CHIP RES,CHIP RES,CHIP RES,CHIP RES,CHIP 10K 10K 33K 33K 33K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R1177 R1178 1-216-085-00 RES,CHIP 1-216-073-71 RES,CHIP 33K 10K 5% 5% 1/10W 1/10W £ 1-453-264-11 TRANSFORMER ASSY, FLYBACK (NX-1680/U2B4) (KV-25K5K) £ 1-453-265-11 TRANSFORMER ASSY, FLYBACK (NX-1681/U2B4) (KV-29K5K) 1-505-484-11 SPEAKER (2.6CM) 1-505-674-11 1-505-673-11 £ 1-571-433-21 £ 1-765-286-11 8-598-432-00 SPEAKER MID RANGE (8CM) SPEAKER WOOFER (10CM) SWITCH, PUSH (AC POWER) CORD, POWER TUNER (FSS-BTP-AC411) £ £ £ £ £ £ PICTURE TUBE (SD-257) (M60LCS60X) (KV-25K5K) PICTURE TUBE (SD-269) (M68LCT60X) (KV-29K5K) DEFLECTION YOKE (Y25GXABA) (KV-25K5K) , DEFLECTION YOKE (Y29GXC2B) (KV-29K5K) ITC (KV-25K5K) ITC (KV-29K5K) 8-733-254-05 8-733-856-05 8-451-404-23 8-451-466-11 8-733-254-76 8-733-856-75 ********************************************************************** ACCESSORIES AND PACKAGING MATERIALS *********************************** 4-395-957-01 4-203-677-01 4-203-670-01 4-203-678-01 4-203-671-01 BAG, PROTECTION INDIVIDUAL CARTON INDIVIDUAL CARTON CUSHION (UPPER) (ASSY) CUSHION (UPPER) (ASSY) (KV-25K5K) (KV-29K5K) (KV-25K5K) (KV-29K5K) 4-203-681-01 CUSHION (LOWER) (ASSY) (KV-25K5K) 4-203-674-01 CUSHION (LOWER) (ASSY) (KV-29K5K) 4-204-276-91 MANUAL, INSTRUCTION (CZECH/ENGLISH/POLISH) < CRYSTAL > X1101 DESCRIPTION 1-767-813-21 VIBRATOR, CRYSTAL REMOTE COMMANDER **************** 1-475-765-11 COMMANDER STANDARD TYPE (RM-883) ******************************************************************** Sony Corporation 9-974-970-01 Sony UK Service Promotions Dept. 70 English 98DP7114-1 Printed in U.K. © 1998.4