Download CDX-GT06/CXS-GT06HP - Wiki Karat

CDX-GT06/CXS-GT06HP
SERVICE MANUAL
US Model
Ver. 1.0 2006.07
• CXS-GT06HP is composed of CDX-GT06,
2 way speaker, 3 way speaker.
(Photo: CDX-GT06)
• The tuner and CD sections have no adjustments.
Model Name Using Similar Mechanism
CDX-GT10W/GT100
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL HARMONIC DISTORTION
22 watts per channel minimum continuous average power into
4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more
than 5% total harmonic distortion.
CD Drive Mechanism Type
MG-611XE-186//C
Optical Pick-up Name
KSS1000E
SPECIFICATIONS
CD Player section
Signal-to-noise ratio:
Frequency response:
Wow and flutter:
120 dB
10 – 20,000 Hz
Below measurable limit
Tuner section
Power amplifier section
Outputs:
Speaker outputs (sure seal connectors)
Speaker impedance:
4 – 8 ohms
Maximum power output: 45 W × 4 (at 4 ohms)
General
Outputs:
FM
Tuning range:
87.5 – 107.9 MHz
Antenna terminal:
External antenna connector
Intermediate frequency: 10.7 MHz/450 kHz
Usable sensitivity:
9 dBf
Selectivity:
75 dB at 400 kHz
Signal-to-noise ratio:
67 dB (stereo), 69 dB (mono)
Harmonic distortion at 1 kHz:
0.5 % (stereo), 0.3 % (mono)
Separation:
35 dB at 1 kHz
Frequency response:
30 – 15,000 Hz
Inputs:
Tone controls:
Power requirements:
Dimensions:
Mounting dimensions:
AM
Tuning range:
Antenna terminal:
Intermediate frequency:
Sensitivity:
530 – 1,710 kHz
External antenna connector
10.7 MHz/450 kHz
30 µV
Mass:
Supplied accessories:
Audio outputs terminal (sub/rear switchable)
Power antenna relay control terminal
Power amplifier control terminal
Antenna input terminal
AUX input jack (stereo mini jack)
Low: ±10 dB at 60 Hz (XPLOD)
Mid: ±10 dB at 1 kHz (XPLOD)
High: ±10 dB at 10 kHz (XPLOD)
12 V DC car battery (negative ground)
Approx. 178 × 50 × 179 mm
(7 1/8 × 2 × 7 1/8 in) (w/h/d)
Approx. 182 × 53 × 161 mm
(7 1/4 × 2 1/8 × 6 3/8 in) (w/h/d)
Approx. 1.2 kg (2 lb 11 oz)
Parts for installation and connections (1 set)
– Continued on next page –
FM/AM COMPACT DISC PLAYER
9-887-357-01
2006G04-1
© 2006.07
Sony Corporation
eVehicle Division
Published by Sony Techno Create Corporation
CDX-GT06/CXS-GT06HP
6 × 9 Speaker
Altavoz de 6 × 9
222 (8 3/4)
237 (9 3/8)
ø 125 (5)
ø 80 (3 1/4)
166 (6 5/8)
ø 75 (3)
4.5 × 7.5 (3/16 × 5/16)
117 (4 5/8)
194 (7 3/4)
153 (6 1/8)
35 (1 7/16)
16 (21/32)
75 (3)
168 (6 5/8)
6 1/2 Speaker
Altavoz de 6 1/2
5
(1
ø 142 (5 5/8)
ø 158 (6 1/4)
5
(7
/ 32
)
/8)
Design and specifications are subject to change
without notice.
ø 168 (6 3/4)
27 (1 1/8)
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
2
Unit: mm (in)
Unidad: mm
2.
6 1/2 Speaker (2-way Speaker)
Speaker
Coaxial 2-way:
Woofer 16 cm (6 3/8 in),
HOP, cone type
Tweeter 4 cm (1 5/8 in),
Al, cone type
Peak power
190 W
Rated power
40 W
Impedance
4Ω
Sensitivity
90 dB/W/m
Frequency response
35 – 22,000 Hz
Mass
Approx. 560 g (1 lb 4 oz) per
speaker
Supplied accessory
Parts for installation
Dimensions
Dimensiones
264 (10 1/2)
6 × 9 Speaker (3-way Speaker)
Speaker
Coaxial 3-way:
Woofer 16 × 24 cm
(6 3/8 × 9 1/2 in), cone type
Midrange 5.5 cm (2 1/4 in),
cone type
Tweeter 1.4 cm (9/16 in),
balanced dome type
Peak power
300 W
Rated power
60 W
Impedance
4Ω
Sensitivity
93 dB/W/m
Frequency response
27 – 30,000 Hz
Mass
Approx. 1,150 g (2 lb 9 oz)
per speaker
Supplied accessory
Parts for installation
ø 5 (7/32)
8.9 (3/8)
44
(1 3/4)
CDX-GT06/CXS-GT06HP
SERVICE NOTES
CAUTION
Use of controls or adjustments or performance of procedures other
than those specified herein may result in hazardous radiation
exposure.
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
breakdown because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.
Notes on Chip Component Replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be damaged
by heat.
If the optical pick-up block is defective, please replace the whole
optical pick-up block.
Never turn the semi-fixed resistor located at the side of optical pickup block.
optical pick-up
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
semi-fixed resistor
EXTENSION CABLE AND SERVICE POSITION
When repairing or servicing this set, connect the jig (extension cable)
as shown below.
• Connect the MAIN board (CNP301) and the SERVO board (CN1)
with the extension cable (Part No. J-2502-076-1).
MAIN BOARD
CNP301
J-2502-076-1
SERVO BOARD
CN1
3
CDX-GT06/CXS-GT06HP
TEST DISCS
Please use the following test discs for the check on the voltage and
the waveforms of the CD section.
TABLE OF CONTENTS
1.
Location of Controls and Basic Operations .................... 5
Connections ..................................................................... 5
YDES-18 (Part No. 3-702-101-01)
PATD-012 (Part No. 4-225-203-01)
Notes on CD-DA/CD-R/CD-RW
• CD playback:
You can play CD-DA and CD-R/CD-RW for audio use.
SOLDER
• UNLEADED
Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
4
GENERAL
2.
DISASSEMBLY
2-1.
2-2.
2-3.
2-4.
2-5.
2-6.
2-7.
2-8.
2-9.
2-10.
Sub Panel Assy ................................................................
CD Mechanism Block .....................................................
Main Board ......................................................................
Chassis (T) Sub Assy .......................................................
Roller Arm Assy ..............................................................
Chassis (OP) Assy ...........................................................
Optical Pick-up ................................................................
SL Motor Assy (M902) ...................................................
LE Motor Assy (M903) ...................................................
Servo Board .....................................................................
3.
DIAGRAMS
3-1.
3-2.
3-3.
3-4.
3-5.
3-6.
3-7.
3-8.
3-9.
3-10.
3-11.
3-12.
Block Diagram –CD Section– .........................................
Block Diagram –Main Section– ......................................
Block Diagram –Display Section– ..................................
Circuit Boards Location ..................................................
Printed Wiring Boards –CD Mechanism Section– ..........
Schematic Diagram –CD Mechanism Section– ..............
Printed Wiring Board –Main Section– ............................
Schematic Diagram –Main Section (1/3)– ......................
Schematic Diagram –Main Section (2/3)– ......................
Schematic Diagram –Main Section (3/3)– ......................
Printed Wiring Boards –Key Section– .............................
Schematic Diagram –Key Section– .................................
4.
EXPLODED VIEWS
4-1.
4-2.
4-3.
4-4.
4-5.
4-6.
Main Section ....................................................................
Front Panel Section .........................................................
CD Mechanism Section (1) (MG-611XE-186//C) ..........
CD Mechanism Section (2) (MG-611XE-186//C) ..........
CD Mechanism Section (3) (MG-611XE-186//C) ..........
CD Mechanism Section (4) (MG-611XE-186//C) ..........
5.
ELECTRICAL PARTS LIST .................................. 37
8
8
9
9
10
10
11
11
12
12
13
14
15
15
16
17
18
19
20
21
22
23
31
32
33
34
35
36
CDX-GT06/CXS-GT06HP
SECTION 1
GENERAL
This section is extracted
from instruction manual.
Location of controls and basic operations
Main unit
CDX-GT06
1 OFF button
To power off; stop the source.
2 Volume control dial/select button
To adjust volume (rotate); select setup items
(press and rotate).
3 EQ3 (equalizer) button
To select an equalizer type (XPLOD,
VOCAL, CLUB, JAZZ, NEW AGE,
ROCK, CUSTOM or OFF).
4 Disc slot
To insert the disc (label side up), playback
starts.
5 Display window
6 Z (eject) button
To eject the disc.
7 DSPL (display)/DIM (dimmer) button
To change display items (press); change the
display brightness (press and hold).
(front panel release) button
8
9 SEEK –/+ buttons
CD:
To skip tracks (press); skip tracks
continuously (press, then press again within
about 1 second and hold); reverse/fastforward a track (press and hold).
Radio:
To tune in stations automatically (press);
find a station manually (press and hold).
0 SOURCE button
To power on; change the source (Radio/CD/
AUX).
qa BTM button
To start the BTM function (press and hold).
qs MODE button
To select the radio band (FM/AM).
qd RESET button (located behind the front
panel)
qf Number buttons
CD:
(3): REP
To play the current track repeatedly.
(4): SHUF
To play the tracks in random order.
Radio:
To receive stored stations (press); store
stations (press and hold).
qg SENS button
To improve weak reception: LOCAL/
MONO.
qh AUX input jack
To connect a portable audio device.
• CONNECTIONS
Connection
Connection example
A
Notes (2-B)
• Be sure to connect the ground lead before connecting the
amplifier.
• The alarm will only sound if the built-in amplifier is used.
Conexion
Ejemplo de conexiones
Notas (2-B)
• Asegúrese de conectar primero el cable de conexión a masa
antes de realizar la conexión del amplifi cador.
• La alarma sonará únicamente si se utiliza el amplifi cador
incorporado.
B
Active subwoofer
(not supplied)
Altavoz potenciador de
graves activo
(no suministrado)
Power amplifier
(not supplied)
Amplifi cador de potencia
(no suministrado)
Rear speaker
(not supplied)
Altavoz posterior
(no suministrado)
* AUDIO OUT SUB/REAR
5
CDX-GT06/CXS-GT06HP
Power amplifier
(not supplied)
Amplifi cador de potencia
(no suministrado)
*1
Active subwoofer
(not supplied)
Altavoz potenciador de
graves activo
(no suministrado)
Rear speaker
(not supplied)
Altavoz posterior
(no suministrado)
*1 RCA pin cord (not supplied)
*2 AUDIO OUT can be switched to SUB
or REAR.
For details, see the supplied Operating
Instructions.
L
R
*1 Cable con terminales RCA
(no suministrado)
*2 AUDIO OUT (Salida de audio) puede
cambiarse a SUB (Secundaria) o
REAR (Posterior).
Para obtener información, consulte el
manual de instrucciones suministrado.
BUS
AUDIO
IN
Fuse (10 A)
Fusible (10 A)
from car antenna
desde la antena del automóvil
2
AMP REM
Blue/white striped
Con rayas azules y blancas
Max. supply current 0.3 A
Corriente máx. de alimentación de 0,3 A
White
Blanco
Left
Izquierdo
Black
Negro
White/black striped
Con rayas blancas y negras
Gray
Gris
Right
Derecho
Blue
Azul
Max. supply current 0.1 A
Corriente máx. de alimentación de 0,1 A
Gray/black striped
Con rayas grises y negras
Green
Verde
Left
Izquierdo
Red
Rojo
Green/black striped
Con rayas verdes y negras
Purple
Morado
Right
Derecho
Purple/black striped
Con rayas moradas y negras
Connection diagram
1 To a metal surface of the car
First connect the black ground lead, then connect the yellow
and red power input leads.
2 To the power antenna control lead or power
supply lead of antenna booster amplifier
Notes
• It is not necessary to connect this lead if there is no power
antenna or antenna booster, or with a manually-operated
telescopic antenna.
• When your car has a built-in FM/AM antenna in the rear/side
glass, see “Notes on the control and power supply leads.”
3 To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting any other
system may damage the unit.
4 To the +12 V power terminal which is energized
in the accessory position of the ignition key
switch
Notes
• If there is no accessory position, connect to the +12 V power
(battery) terminal which is energized at all times.
Be sure to connect the black ground lead to a metal surface
of the car first.
• When your car has a built-in FM/AM antenna in the rear/side
glass, see “Notes on the control and power supply leads.”
5 To the +12 V power terminal which is energized
at all times
Be sure to connect the black ground lead to a metal surface of
the car first.
Notes on the control and power supply leads
• The power antenna control lead (blue) supplies +12 V DC when
you turn on the tuner.
• When your car has built-in FM/AM antenna in the rear/side glass,
connect the power antenna control lead (blue) or the accessory
power input lead (red) to the power terminal of the existing
antenna booster. For details, consult your dealer.
• A power antenna without a relay box cannot be used with this unit.
Memory hold connection
When the yellow power input lead is connected, power will always
be supplied to the memory circuit even when the ignition switch is
turned off.
Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms, and with
adequate power handling capacities to avoid its damage.
• Do not connect the speaker terminals to the car chassis, or
connect the terminals of the right speakers with those of the left
speaker.
• Do not connect the ground lead of this unit to the negative (–)
terminal of the speaker.
• Do not attempt to connect the speakers in parallel.
• Connect only passive speakers. Connecting active speakers (with
built-in amplifiers) to the speaker terminals may damage the unit.
• To avoid a malfunction, do not use the built-in speaker leads
installed in your car if the unit shares a common negative (–) lead
for the right and left speakers.
• Do not connect the unit’s speaker leads to each other.
Note on connection
If speaker and amplifier are not connected correctly, “FAILURE”
appears in the display. In this case, make sure the speaker and
amplifier are connected correctly.
Diagrama de conexión
1 A una superficie metálica del automóvil
Conecte primero el cable de conexión a masa negro, y después
los cables con rayas naranjas y blancas, amarillo, y rojo de
entrada de alimentación.
2 Al cable de control de la antena motorizada
o al cable de fuente de alimentación del
amplificador de señal de la antena
Notas
• Si no se dispone de antena motorizada ni de amplifi cador
de antena, o se utiliza una antena telescópica accionada
manualmente, no será necesario conectar este cable.
• Si el automóvil incorpora una antena de FM/AM en el cristal
posterior o lateral, consulte “Notas sobre los cables de control
y de fuente de alimentación”.
3 A la toma AMP REMOTE IN de un amplificador
de potencia opcional
Esta conexión es sólo para amplifi cadores. La conexión de
cualquier otro sistema puede dañar la unidad.
4 Al terminal de alimentación de +12 V que
recibe energía en la posición de accesorio del
interruptor de la llave de encendido
Notas
• Si no hay posición de accesorio, conéctelo al terminal de
alimentación (batería) de +12 V que recibe energía sin
interrupción.
Asegúrese de conectar primero el cable de conexión a masa
negro a una superfi cie metálica del automóvil.
• Si el automóvil incorpora una antena de FM/AM en el cristal
posterior o lateral, consulte “Notas sobre los cables de control
y de fuente de alimentación”.
5 Al terminal de alimentación de +12 V que recibe
energía sin interrupción
Asegúrese de conectar primero el cable de conexión a masa
negro a una superficie metálica del automóvil.
Notas sobre los cables de control y de fuente de alimentación
• El cable de control de la antena motorizada (azul) suministrará cc
de + 12 V cuando conecte la alimentación del sintonizador.
• Si el automóvil dispone de una antena de FM/AM incorporada
en el cristal posterior o lateral, conecte el cable de control de
antena motorizada (azul) o el cable de entrada de alimentación
auxiliar (rojo) al terminal de alimentación del amplificador de
antena existente. Para obtener más información, consulte a su
distribuidor.
• Con esta unidad no es posible utilizar una antena motorizada sin
caja de relé.
Conexión para protección de la memoria
Si conecta el cable de entrada de alimentación amarillo, el circuito
de la memoria recibirá siempre alimentación, aunque apague el
interruptor de encendido.
Notas sobre la conexión de los altavoces
• Antes de conectar los altavoces, desconecte la alimentación de la
unidad.
• Utilice altavoces con una impedancia de 4 a 8 Ω con la capacidad
de potencia adecuada para evitar que se dañen.
• No conecte los terminales de altavoz al chasis del automóvil, ni
conecte los terminales del altavoz derecho con los del izquierdo.
• No conecte el cable de conexión a masa de esta unidad al
terminal negativo (–) del altavoz.
• No intente conectar los altavoces en paralelo.
• Conecte solamente altavoces pasivos. Si conecta altavoces
activos (con amplifi cadores incorporados) a los terminales de
altavoz, puede dañar la unidad.
• Para evitar fallas de funcionamiento, no utilice los cables de
altavoz incorporados instalados en el automóvil si la unidad
comparte un cable negativo común (–) para los altavoces derecho
e izquierdo.
• No conecte los cables de altavoz de la unidad entre sí.
Nota sobre la conexión
Si el altavoz y el amplificador no están conectados correctamente,
aparecerá “Failure” en la pantalla. En tal caso compruebe la
conexión de ambos dispositivos.
6
ANT REM
Yellow
Amarillo
CDX-GT06/CXS-GT06HP
SECTION 2
DISASSEMBLY
Note: This set can be disassemble according to the following sequence.
SET
2-1.
SUB PANEL ASSY
(Page 8)
2-2.
CD MECHANISM BLOCK
(Page 8)
2-3.
MAIN BOARD
(Page 9)
2-7.
2-4.
CHASSIS (T) SUB ASSY
(Page 9)
2-5.
ROLLER ARM ASSY
(Page 10)
2-6.
CHASSIS (OP) ASSY
(Page 10)
2-8.
SL MOTOR ASSY (M902)
(Page 11)
OPTICAL PICK-UP
(Page 11)
2-10. SERVO BOARD
(Page 12)
2-9.
LE MOTOR ASSY (M903)
(Page 12)
7
CDX-GT06/CXS-GT06HP
Note: Follow the disassembly procedure in the numerical order given.
2-1. SUB PANEL ASSY
3 two claws
2 two claws
1 two screws
(+PTT 2.6 × 6)
4 sub panel assy
2-2. CD MECHANISM BLOCK
6 bracket (CD)
7 CD mechanism block
5 two screws
(+PTT 2.6 × 4)
2 screw
(+PTT 2.6 × 6)
3
4 CNP301
1 screw
(+PTT 2.6 × 6)
8
CDX-GT06/CXS-GT06HP
2-3. MAIN BOARD
1 three screws
(+BTT 2.6 × 5)
2 two screws
(+PTT 2.6 × 8)
3 MAIN board
2-4. CHASSIS (T) SUB ASSY
4 claw
2 two screws
(+P 1.7 × 2.2)
1 two screws
(+P 1.7 × 2.2)
6 chassis (T) sub assy
5 SENSOR board
3 claw
9
CDX-GT06/CXS-GT06HP
2-5. ROLLER ARM ASSY
3 washer (1.1-2.5)
5 roller arm assy
4 gear (RA1)
2 spring (RAR)
1 spring (RAL)
2-6. CHASSIS (OP) ASSY
7
0 chassis (OP) assy
9 compression spring (damper)
lever (D)
5
1 optical pick-up (16 core)
(CN2)
8 two compression springs
(damper)
4 gear (LE1)
6
slider (R)
3 tension spring (KF60)
2 Remove the six solders.
10
CDX-GT06/CXS-GT06HP
2-7. OPTICAL PICK-UP
2 chucking arm sub assy
5 claw
1 tension spring (CHKG)
7 optical pick-up
6 main shaft
4 rack (SL)
3 screw
(+B 1.4 × 5)
2-8. SL MOTOR ASSY (M902)
1 screw
(+P 1.4 × 1.8)
2 SL motor assy (M902)
11
CDX-GT06/CXS-GT06HP
2-9. LE MOTOR ASSY (M903)
7 screw
(+M 1.7 × 2.5)
9 gear (LE) assy
8 bearing (LEB-N)
qd two toothed lock screws
(+M 1.4 )
0 screw
(+M 1.7 × 2.5)
2 gear (LE1)
lever (D)
3
bracket (LEM-N)
qa screw
(+M 1.7 × 2.5)
qs
qf LE motor assy
(M903)
4
5 screw
(+P 1.7 × 2.2)
slider (R)
6 leaf spring (LE)
1 Remove the two solders.
2-10. SERVO BOARD
1 Remove the eight solders.
6 SERVO board
2 Remove the three solders.
4 toothed lock screw
(M 1.7 × 2.5)
5 claw
3 optical pick-up (16 core)
(CN2)
12
CDX-GT06/CXS-GT06HP
SECTION 3
DIAGRAMS
3-1. BLOCK DIAGRAM — CD SECTION —
• R-ch is omitted due to same as L-ch.
• Siganal Path
: CD PLAY
DETECTOR
PD1
PD1
PD2
82 A
PD2
77 AGCI
RFO 78
AGCO 76
71 RFI
EFM 68
69 ASY
ROUT 16
84 B
CD-L
LOUT 20
I-V AMP
RF AMP,DIGITAL SERVO,
DIGITAL SIGNAL PROCESSOR
IC1
E
E
F
F
87 E
FEO 93
92 FE–
86 F
TEO 96
95 TE–
TE2 97
LD
AUTOMATIC
POWER
CONTROL
Q1
1 LD
93 CD_MUTE-R
18 CD_SI
19 CD_SO
20 CD_SCK
RFOK 6
INTQ 7
STB 10
A0 9
RST 8
PD 2
PD
89
55
92
91
90
CD RFOK
CD INTQ
CD_STB
CD_A0
CD RST
SYSTEM CONTROL
IC501 (1/3)
OPTICAL
PICK-UP BLOCK
(KSS1000E)
2-AXIS DEVICE
94 CD_MUTE-L
SO 12
SI 13
SCK 11
LD
PD
LMUTE 30
RMUTE 29
98 TEC
LASER DIODE
FOCUS/TRACKING COIL DRIVE,
SLED/SPINDLE/LOADING
MOTOR DRIVE
IC2
XTAL 23
FCS+
FCS–
11 VO2–
OPIN2+ 5
52 FD+
12 VO2+
OPIN2– 6
53 FD–
13 VO1–
OPIN1+ 2
54 TD+
OPIN1– 3
55 TD–
X1
16.9344MHz
XTAL 24
(FOCUS)
(TRACKING)
TRK+
TRK–
14 VO1+
SW1
(DOWN)
SW2
(SELF)
M902
(SLED)
M
M901
(SPINDLE)
M
M903
(LOADING)
M
99 CD_DSW
96 CD_SELFSW
15 VO4+
OPIN4+ 27
56 SD+
16 VO4–
OPIN4– 26
57 SD–
SW3
(DISC IN)
95 CD_INSW
SW4
(LIMIT)
100 CD_LIMIT
17 VO3+
OPIN3+ 24
58 MD+
18 VO3–
OPIN3– 23
59 MD–
10 VOL+
FWD 1
97 CD LM LO
9 VOL–
REV 28
98 CD LM EJ
CDX-GT06/CXS-GT06HP
13
13
MAIN
SECTION
(Page 14)
R-CH
83 C
85 D
A
CDX-GT06/CXS-GT06HP
3-2. BLOCK DIAGRAM — MAIN SECTION —
ELECTRONIC VOLUME
IC401
CD
(Page 13) SECTION
A
CD-L
R-CH
J901
OUT SUB-L 17
OUT SUB-R 18
L
R-CH
R-CH
R-CH
AUX
AUX
BUFFER
IC901
TU1
(TUNER UNIT)
J1
(ANTENNA)
9 CD LCH
8 CD RCH
1 ANT
L-CH 4
R-CH 3
R-CH
R
5 AUX LCH
3 AUX RCH
I2C-BUS
CONTROLLED
POWER AMP/
MULTIPLE
VOLTAGE
REGULATOR
IC750
MUTE
Q481
7 TU LCH
6 TU RCH
OUT FL 23
12 IN FL
OUT RL 22
OUT FR 25
OUT RR 24
VCC 10
TU VDD 11
E2P VDD 15
TU-SCL 13
TU-SDA 14
J330
AUDIO OUT
REAR
11 IN RL
R-CH (FRONT)
R-CH (REAR)
MUTE
Q441
CN601
1
FL+
9
FL–
OUT FL+ 5
OUT FL– 3
2
OUT RL+ 9
OUT RL– 7
MUTE
Q461
10
MUTE 29
AUDIO+8.3V
TU+5V
BU+3.3V
SCL 30
SDA 31
SCL
SDA
MUTE DRIVE
Q478,479
D479
R-CH
BATT
SCL
SDA
I2C CKO 33
I2C SIO 34
S-METER 6
TU MUTE 7
39 VSM
12 TU ATT
E2P SCL 16
E2P SDA 17
25 EEP CKO
24 EEP SIO
SDA
SCL
SCL
SDA
BATT
2 SDA
4 SCL
VOL ATT 9
ATT
BEEP
AMP STB
DIAG
86
5
26
8
16 BEEP
22 STB
25 DIAG
30
37
31
33
34
: CD PLAY
D580,581
BU IN 54
: AM
: AUX
BATTERY CHECK
Q580-582
BATT
TU+5V
CDX-GT06/CXS-GT06HP
14
14
7
15
TEST IN 73
: FM
16
TU+5V REG
Q1
BATT
AUDIO+8.3V
BU+3.3V
SERVO+3.3V
MECHA+6V
PANEL+B
ACCESSORY
CHECK
Q631
ACC IN 72
• R-CH is omitted due to same as L-CH.
• Signal Path
FU601
VP 35
VP1 20
VP2 6
AUDIO8.3V
B.UP+B
SERVO3.3V
MECHA6V
PANEL+B
4
FR+
12
FR–
3
RR+
11
RR–
5
AMP-REM
6
ANT-REM
AMP-REM 29
ANT-REM 27
SYSTEM CONTROL
IC501 (2/3)
RL+
RL–
AUDIO+8.3V
ACC
TEST
CDX-GT06/CXS-GT06HP
3-3. BLOCK DIAGRAM — DISPLAY SECTION —
SYSTEM CONTROL
IC501 (3/3)
• NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
41 KEYIN0
D503
KEY ACKNOWLEDGE
SWITCH
Q664
RE901
PUSH SELECT
(VOLUME)
LCD SO 28
LCD CKO 29
LCD CE 27
52 KEY ACK
76 XKEY ON
5
S1
|
|
55
S48 •
60
64 DI
CLK
63 CL
62 CE
LCD901
LIQUID
CRYSTAL
DISPLAY
PANEL
COM4 51
|
|
COM1 54
DIMMER
40 KEYIN1
BACK LIGHT
KEY MATRIX
LSW901–903,908–920
THIS NOTE IS COMMON FOR PRINTED WIRING
BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is
printed in each block.)
LCD DRIVER
IC901
1
2
PANEL+B
ROTARY
ENCODER
31 RE IN0
32 RE IN1
(
LED932
LCD BACK
LIGHT
For schematic diagrams.
For printed wiring boards.
Note:
• All capacitors are in µF unless otherwise noted. (p: pF)
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.
•
f
: internal component.
• C : panel designation.
Note:
• X : parts extracted from the component side.
• Y : parts extracted from the conductor side.
a
: Through hole.
•
: Pattern from the side which enables seeing.
•
(The other layers' patterns are not indicated.)
Note: The components identified by mark 0 or dotted line
with mark 0 are critical for safety.
Replace only with part number specified.
)
LSW901–903,
908–920
•
•
•
•
DIMMER
LED DRIVE
Q931
•
LCD BACK LIGHT
LED DRIVE
Q932
7 NOSE DET
•
RESET
IC602
BU+3.3V
77 RESET
2 VDD VOUT 1
•
S702
RESET
X502
32.768kHz
•
79 XOUT
80 XIN
OSC IN 82
OSC OUT 83
X501
18.432MHz
•
•
A : B+ Line.
B : B– Line.
H : adjustment for repair.
Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
CD mechanism section
no mark : CD PLAY
Main (1/3), (2/3), (3/3) and Key sections
no mark : FM
(
) : AM
<
> : CD PLAY
∗ : Impossible to measure
Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production
tolerances.
Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production
tolerances.
Circled numbers refer to waveforms.
Signal path.
J : CD PLAY
F : FM
f : AM
L : AUX
3-4. CIRCUIT BOARDS LOCATION
SERVO board
SENSOR board
tuner unit
(TU1)
MAIN board
KEY board
JACK board
CDX-GT06/CXS-GT06HP
15
15
Caution:
Pattern face side:
(Side B)
Parts face side:
(Side A)
Parts on the pattern face side seen from the
pattern face are indicated.
Parts on the parts face side seen from the
parts face are indicated.
C
Q
These are omitted
B E
BE C
These are omitted
ECB
These are omitted
CDX-GT06/CXS-GT06HP
3-5. PRINTED WIRING BOARDS — CD MECHANISM SECTION — • Refer to page 15 for Circuit Boards Location.
1
2
3
4
5
6
7
: Uses unleaded solder.
8
9
10
11
12
13
14
A
R8
R44
R42
R41
Q1
C7
(Page 18)
C34
C19
C18
R80
R84
MAIN
BOARD
CNP301
2
R70
C17
FB1
CN
D
R12
C35
C39 R15
C21
C37
C26
C23
R14
R6
R7
C20
R78
R82
R72
C25
TP21
B7
R9
FM
R74
R76
C27
C13
JR40
C28
C38
R1
JR41
R4
R13
C36
R11
R3
C30
IC1
C29
C31
R10
C32
JR90
JR91
C
C11
C1
X1
FB2
C2
C5
FB3
R2
R45
C6
B
R5
FMB9
FM
B8
R83 R85
R79
C76
C78 C79
CN1
C72 C71
C70
C73
SW3
R81
C77
IC2
12
C74
F
C75
R77
R75 R73
R71
E
1-864-902-
SW2
(12)
11
FMB10
SW1
(DOWN)
12
G
1-864-902-
CDX-GT06/CXS-GT06HP
16
16
(12)
1-864-903- (11)
CDX-GT06/CXS-GT06HP
• Refer to page 24 for Waveforms.
• Refer to page 24 for IC Block Diagram.
3-6. SCHEMATIC DIAGRAM — CD MECHANISM SECTION — • Refer to page 27 for IC Pin Description of IC1.
C20
R9
C25
Q1
TP32
C23
R7
C21
C19
TP19
CN2
C18
C17
R6
TP33
R14 R15
R13
C36
TP31
C38
C37
TP30
TP14 R12
TP20
C39
TP29
C26
TP21
C35
C27
TP28
TP27
C34
R1
TP26
TP13
R11
C28
C13
TP12
IC1
TP11
TP22
TP10
C29
TP9
C30
TP8
TP23
C31
TP7
TP24
TP6
TP5
TP4
TP25
TP3
SW4
TP2
TP81
C32
TP1
TP80
CN1
FB3
C11
TP65
JR90
JR91
TP64
TP63
TP62
M901
TP61
TP85
TP83
M902
TP60
FB2
R10
R8
R5
R3
R2
R4
C1
TP84
TP82
X1
C5
R45
TP59
R44
TP58
TP57
C6
TP56
FB1
TP55
C2
TP54
TP48
C7
TP27
TP87
TP52
R41
TP51
JR41
SW3
JR40
TP28
TP88
TP29
TP89
TP53
TP49
R42
TP50
SW2
TP47
TP46
TP45
TP44
IC B/D
SW1
TP43
TP90
TP42
TP91
TP41
TP40
R70
R71
C70
R72
R73
C71
R74
R75
R76
R77
IC2
C79
R85
R84
C78
R83
R82
C72
C77
R81 R80
C73
C76
R79 R78
TP100
C74
TP75
M903
TP92
TP74
TP93
TP71
TP70
TP73
TP72
C75
CDX-GT06/CXS-GT06HP
17
17
(Page 21)
CDX-GT06/CXS-GT06HP
3-7. PRINTED WIRING BOARD — MAIN SECTION — • Refer to page 15 for Circuit Boards Location.
2
1
3
4
5
: Uses unleaded solder.
6
7
8
9
10
11
12
13
14
J330
AUDIO OUT
REAR
R
JC754
JC795
YEL
C474
C751
R482
C765 IC750
R461
JW104
JW105
C918
D719
R901
YEL
D601
D760
D752
D751
JW26
R514
R671
R565
FB303
C303
C305
JW46
JW51
JW87
C509
R568
Q664
C519
R680
R601
JW82
R584
JW65
IC602
3
2
4
1
R536
R517
R561
R543
R535
JW62
R583
R582
R631
R541
Q581
Q582
R673
R585
31
S702
1-868-117-
J
CN701
X501
(Page 22)
CDX-GT06/CXS-GT06HP
18
18
Location
F-3
E-6
I-5
F-11
F-11
C-10
D-8
C-9
I-4
D-7
D-7
D-7
D-7
C-5
C-6
C-6
C-6
D-8
D-8
C-9
D-9
I-3
IC401
IC501
IC602
IC750
IC901
E-3
H-6
I-9
B-6
H-2
Q1
Q431
Q441
Q451
Q461
Q471
Q478
Q479
Q481
Q580
Q581
Q582
Q631
Q664
F-2
B-4
B-4
C-4
D-4
B-3
E-6
E-5
C-3
F-11
I-10
I-10
H-10
I-7
FB606
JW58
R567
R519
JC501
C502
FMB4
JC504
D503
R556
R540
JW44
1
50
C514
R503
C301
C343
JW38
IC
R522
R505
R513
R902
C512
C501
R504
FB603
D903
R533
R674
R558
C917
R564
R672
R529
C631
R636 R563
C507
C516
R632
Ref. No.
D1
D479
D503
D580
D581
D601
D609
D617
D719
D751
D752
D753
D754
D755
D756
D757
D758
D759
D760
D761
D762
D903
JW119
C508
C513
R634
R633
R508
X502
R518
R521
Q631
R524
R509
R512
R502
JW139
JW138
D704
JW54
R904
R539
R523
C511
R511
JW74
C902
JW128
JW70
R903
JW133
C901
R566
C510
C503
R510
JW108
R911
R905
I
JW71
R906
FB501
JC536
R525
L501
C504
R570
JW76
R913
C903
R914
IC901
R912
R577
R663
JW35
R661
R575
JW68
JW154
JW67
R907
R676
R756
JW34
R664
JW109
C306
R526
R675
R530
R544
JW103
JW155
JW168
H
D759
R527
JW40
JW69
JW121
JW122
C905
R571
FMB3
R557
R662
R528
R507
R532
R910
R681
R560
R757
JW80
JW156
CN1
(Page 16)
JW117
JW52
G
D580
FB311
JW63
R4
R677
R572
R550
R534
FB310
JC534
R538
JW83
JW107
C407
FB604
R559
C756
JW123
C307
R301
JW75
JW167
JW169
JW166
JW160
JW161
JW162
R5
D581
FB301
R531
R551
JW89
R13
JW100
JW106
Q580
FB307
JW28
JW90
• Semiconductor
Location
JW115
FB305
FB306
JW56
JW81
C410
FB410
FB605
JW50
JW150
Q1
C406
C411
R516
C5
JW29
JW130
JW97
JW30
JW72
C308
R302
X501
L1
JW96
R515
JW129
C302
JW95
C755
JW66
JW124
JW27
FB302
L301
JW141
JW91
R12
C7
C754
R410
CNP301
Q479
R752
R411
JC681
JW55
JW101
JW131
JW132
R407
D1
JW23
D479
R408
FB411
JW94
C4
R3
FB1
C479
R479
R409
F
C622
JW118
IC401
JW164
JW165
JW163
JW93
R406
R1
R2
Q478
FB304
C776
C413
C6
D754
JW25
JW92
JW42
R401
JW111
JW24
C623
JW88
C412
R405
C13
JW31
JW32
JW39
C401
C12
L601
C602
D762
C770
C431
E
R609
D757
C461
JW18
C404
C405
JW137
JW11
JW12
JW13
C750
JW20
D761
D609
D753
C471
R452
R462
Q461
R441
C481
D
C769
C758
D758
C462
C441
TU1
JW17
D756
C455
C465
C601
C618
Q451
D755
R451
JC1
R471
D617
JW5
C435
JW6
R431
C452
JW8
C432
JW2
C617
JW7
Q481
C445
R481
JW15
JW16
C451
JW142
JW143
C
R432
C442
JW22
JW21
JW14
JW3
C753
R472
JW9
JW153
C763
R442
C764
JW1
Q431
Q441
CN601
C774 JW144
FU601
C771
B
Q471
JC753
C775
JC756
C484
JW10
L
JC755
J1
(ANTENNA)
A
S702
RESET
(31)
CDX-GT06/CXS-GT06HP
3-8. SCHEMATIC DIAGRAM — MAIN SECTION (1/3) — • Refer to page 25 for IC Block Diagram.
C484
TU1
J330
IC B/D
IC401
C401
R12
R2
R3
J1
FB410
C411
C410
R13
JC1
FB411
C474
C413
C405 C404
R405
C412
C431
C435
C432
R451
C455
C452
R441
C445
C442
C465
C462
R431
R432
Q431
R452
Q451
R406
C7
R407
FB1
C406
R408
C407
C451
R409
C5
R401
R411
C441
C13
R4
R442
Q441
R462
Q461
R410
D1
R5
R905
C461
C6
C4
C12
R461
R913
R906 R912
R1
C481 R481
Q1
L1
R482
JW169
R472
C471
C902
C901
Q481
Q471
(Page 20)
R471
IC901
Q479
R914
C903
Q478
R903
R904
D479
R907
C479
R911
C905
D903
R910
(Page 21)
CDX-GT06/CXS-GT06HP
19
19
CDX-GT06/CXS-GT06HP
3-9. SCHEMATIC DIAGRAM — MAIN SECTION (2/3) — • Refer to page 26 for IC Block Diagram.
JC795
C775
C764
C765
C774
IC B/D
C751
D751
D752
C750
D753
D754
JC754
JC755
D755
D756
IC750
TDA8589BJ/N2/R1
D757
CN601
D758
D759
D760
JC753
(Page 19)
R609
C753
C618
C754
D761
C769
R752
C755
C770
L601
C756
C602
C771
JW111
JC681
C623
C622
C776
C758
Q631
R633
R634
D617
D762
JC756
R479
C617
C763
C631
R631
D609
R632
(Page 21)
CDX-GT06/CXS-GT06HP
20
20
C601
D601
FU601
CDX-GT06/CXS-GT06HP
• Refer to page 24 for Waveforms.
3-10. SCHEMATIC DIAGRAM — MAIN SECTION (3/3) — • Refer to page 29 for IC Pin Description of IC501.
(Page 19)
(Page 20)
(Page 17)
L301
FB603
D719
CN701
FB304
CNP301
R516
FB303
C343
R515
JW55
C301
C308
C302
FB305
FB310
R302
FB311
R301
FB302
FB307
FB306
C303
(Page 23)
R901
JW107 FB301
C307
R902
C917
C918
D704
JW141
C305
C306
JW28
FB604
JC534
R531
R533
R556
R535
R519 R536
IC602
JW46
FB606
R601
R558
C508
X502
C507
S702
C509
R680
R674
R543
R568
C519
JC501
R517
R672
FB605
R636
Q664
R518
R529
R541
R563
R585
R561
X501
R565
R508
R540
R584
Q581
D503
R567
C510
L501
R509
C514
JC504
D580
R582
Q582
C511
R566
R675
R671 C502
R505
R673 R504
R539
R503
C512
R524
IC501
R525
R502
R523
C516
C501
JC536
C513
R526
R527
R681
R677
R572
R528
Q580
D581
R676
R571
R560
R661 R522
R530 R559
R510
R514
FB501
R551
R550
R507
R538
R513
CDX-GT06/CXS-GT06HP
21
R664
R662
C503
21
R532
R512
R570
JW35
C504
R511
R575
R544
R577
R534
R557
R757
JW38
JW34
R663
R756
R521
R583
CDX-GT06/CXS-GT06HP
3-11. PRINTED WIRING BOARDS — KEY SECTION — • Refer to page 15 for Circuit Boards Location.
1
2
3
4
5
: Uses unleaded solder.
6
7
8
9
10
11
13
12
A
LED932
(LCD BACK LIGHT)
LED951
LSW908
R902
B
LSW901
R957
LSW910
LCD901
LIQUID CRYSTAL DISPLAY PANEL
LED932
LSW910
LSW909
LSW920
LSW920
DSPL/DIM
R903
R958
SEEK–
LSW911
R909
R953
R952
R954
C
LSW901
R942
LSW908
EQ3
LSW909
M>
SEEK+
R941
R943
LSW902
LSW902
OFF
52
1
LSW914
LSW912
LSW903
LSW915
LSW916
R910
R918 LSW919
LSW918
LSW917
LSW913
12
R917
R916
1-868-118- (12)
D
LSW911
BTM
LSW903
SOURCE
LSW913
1
LSW912
MODE
LSW914
LSW915
3/REP
2
LSW917
5
LSW916
4/SHUF
LSW919
SENS
LSW918
6
RED
R
BLK
E
GND
WHT
12
L
1-868-119- (12)
(Page 18)
F
MAIN BOARD
CN701
B
12
(12)
R912
R913
R949
R950
R914
WHT
BLK
GND L
D982
R933
R932 R944
RED
FB902
FB901
R
R945
R982
R981
R985
D981
R984
C981
RE901
PUSH SELECT
(VOLUME)
R987
R978
R931
FMB3
C986
C985
R904
R906
R901
I
R991
IC901
FB903
D901
R955
• Semiconductor
Location
R976
Q932
R974
D903
Q931
R977
R979
RE901
FMB4
R934
R907 R908
2
J901
AUX
CN901
R947
R956
R905
H
3
R946
R948
R951
1
R915
C983
R986
C984
C921
R922
G
C922
R921
1-868-119R911
1-868-118-
CDX-GT06/CXS-GT06HP
22
22
12
(12)
Ref. No.
D901
D903
D981
D982
Location
H-10
H-10
H-10
H-10
IC901
H-8
LED932
B-5
Q931
Q932
H-5
H-5
CDX-GT06/CXS-GT06HP
3-12. SCHEMATIC DIAGRAM — KEY SECTION —
R981
LSW909(2/2)
LSW902(2/2)
R943
LSW919(2/2)
LSW914(2/2)
LSW916(2/2)
LSW908(2/2)
R955
R931
R932
LED951
R933
R942
R957
R956
R941
R958
LSW903(2/2)
LSW913(2/2)
LSW918(2/2)
LSW910(2/2)
LSW920(2/2)
LSW901(2/2)
LSW917(2/2)
LSW915(2/2)
R982
R952
LSW911(2/2)
LSW912(2/2)
LED932
R948
R950
R953
R945
R947
R949
R951
R954
D981
R934
R986
R987
R946
D982
R944
Q931
IC901
R984
R985
C983
C984
C981
R977
C985
C986
R978
R979
Q932
R991
D901
CN901
D903
RE901
R976
LCD901
R974
R922
R901
R902
R903
R921
R905
R904
LSW901(1/2)
LSW902(1/2)
LSW903(1/2)
R906
R907
R908
R909
LSW909(1/2)
LSW910(1/2)
LSW911(1/2)
R916
R917
R918
LSW920(1/2)
LSW916(1/2)
R915
LSW919(1/2)
R914
LSW918(1/2)
R913
LSW917(1/2)
R912
LSW915(1/2)
R911
LSW913(1/2)
R910
LSW914(1/2)
C921
LSW912(1/2)
FB901
FB903
FB902
(Page 21)
LSW908(1/2)
C922
J901
CDX-GT06/CXS-GT06HP
23
23
CDX-GT06/CXS-GT06HP
• WAVEFORMS
• IC BLOCK DIAGRAMS
— SERVO Board — (CD PLAY)
1
— MAIN Board —
1
IC1 wd (XTAL)
IC2 BA5966FP-FE2 (SERVO Board)
IC501 i; (XIN)
28 REV
FWD 1
0.7Vp-p
1.2Vp-p
FWD REV
27 OPIN4+
LDCTL 2
32.768 kHz
16.9344MHz
0.2 V/DIV, 0.2 µsec/DIV
OUTR OUTF
NC 3
26 OPIN4–
OPOUT1 4
0.2 V/DIV, 0.1 µsec/DIV
25 OPOUT4
NC 5
2
2
IC1 uj (AGCI)
24 OPIN3+
NC 6
IC501 is (OSC IN)
23 OPIN3–
OPOUT2 7
22 OPOUT3
0.8Vp-p
0.85V to
1.45Vp-p
POWVCC 8
VOL– 9
18.432 MHz
VCC
MUTE
VOL+ 10
1 V/DIV, 0.1 µsec/DIV
0.5 V/DIV, 0.5 µsec/DIV
3
18 VOL3–
VOL2– 11
LEVEL
SHIFT
IC1 od (FEO)
LEVEL
SHIFT
VOL2+ 12
17 VOL3+
VO1– 13
VO1+ 14
Approx. 620mVp-p
200 mV/DIV, 5 msec/DIV
4
16 VOL4–
LEVEL
SHIFT
0V
IC1 oh (TEO)
0V
Approx. 200mVp-p
50 mV/DIV, 5 msec/DIV
CDX-GT06/CXS-GT06HP
24
24
21 MUTE
20 VOL+
19 GND
LEVEL
SHIFT
15 VOL4+
CDX-GT06/CXS-GT06HP
DGND
SDA
SCL
MUTE
SEL
ADJ
VCC
OUT
FR
OUT
RR
OUT
FL
OUT
RL
NC
NC
NC
OUT
SUB R
OUT
SUB L
IC401 BD3806AFS-E2 (MAIN Board (1/3))
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
VCC
2
I C BUS
LOGIC
FADER
(0~-58,
-∞dB)
VCO
FADER
(0~-58,
-∞dB)
FADER
(0~-58,
-∞dB)
FADER
(0~-58,
-∞dB)
GAIN+ATT
(+10~-29,
-∞dB)
2ND ORDER LPF
fc:OFF,80,120,160Hz
Q: 0.707
BASS
fo:60,70,80,100,120,140,160,200Hz
Q:0.5,0.75,1,1.25
2ND ORDER
LPF
MIX
TONE
PASS
TONE
PASS
MIDDLE
fo:500Hz,1kHz
Q:1
BASS,TREBLE, MIDDLE
(-15dB~+15dB,1dB STEP)
BASS,TREBLE, MIDDLE
(-15dB~+15dB,1dB STEP)
TABLE
fo:5,7.5,10,12.5kHz
VOLUME
(+23~-79dB,-∞dB
1dB STEP)
VOLUME
(+23~-79dB,-∞dB
1dB STEP)
fc:53.3kHz
fc:53.3kHz
ANTI-ALIASING
FILTER
ANTI-ALIASING
FILTER
INPUT GAIN
(0~15dB,1dB STEP)
INPUT GAIN
(0~15dB,1dB STEP)
MUTE
MUTE
INPUT SELECTOR
(3 STEREO INCLUDE 1 ISOLATION INPUT)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
AGND
FIL
AUX
RCH
AN
AUX
LCH
TU
RCH
TU
LCH
CD
RCH
CD
LCH
NC
NC
NC
NC
NC
NC
NC
VCC/2
25
CDX-GT06/CXS-GT06HP
IC750 TDA8589BJ/N2/R1 (MAIN Board (2/3))
TAB 1
2 SDA
OUT-FL- 3
I2C BUS
4 SCL
FL
OUT-FL+ 5
6 VP2
OUT-RL- 7
RL
8 PGND3
OUT-RL+ 9
PROTECTION/
DIAGNOSTIC
IN-RR 15
12 IN-FL
14 IN-FR
MUTE
S-GND 13
10 SVR
MUTE
IN-RL 11
16 BEEP
VP
OUT-RR+ 17
RR
18 PGND2
OUT-RR- 19
20 VP1
OUT-FR+ 21
FR
OUT-FR- 23
STANDBY/
MUTE
22 STB
CHIP DETECT/
DIAGNOSTIC
24 PGND1
BATTERY
DETECTION
DIAG 25
TEMPERATURE
PROTECTION
ENABLE
LOGIC
26 RST
ANT-REM 27
SWITCH
AMP-REM 29
SWITCH
28 CRES
REGULATOR
30 AUDIO8.3V
SERVO5V 31
MECH6V 33
32 GND
34 PANEL+B
VP 35
REFERENCE
VOLTAGE
B.UP+B 37
26
REGULATOR
36 CBU
LOADDUMP
PROTECTION
BACK-UP
SWITCH
CDX-GT06/CXS-GT06HP
• IC PIN DESCRIPTIONS
IC1 µPD63712GC-8EU-A (RF AMP, DIGITAL SERVO, DIGITAL SIGNAL PROCESSOR) (SERVO BOARD)
Pin No.
Pin Name
I/O
Pin Description
1
LD
O
Laser diode ON/OFF control signal output (L: laser OFF, H: laser ON)
2
PD
I
Dimmer monitor input from optical pick-up laser diode.
3
PN
I
Not used. (Fixed at L in this set.)
4
AVDD
—
Analog power supply pin (+3.3 V)
5
DGND
—
Ground pin
6
RFOK
O
RFOK signal output to system control IC.
7
INTQ
O
CD text pack synchronization signal output to system control IC.
8
RST
I
CD reset signal input from system control IC.
9
A0
I
10
STB
I
Data strobe signal input from system control IC.
11
SCK
I
Serial clock signal input from system control IC.
12
SO
O
Serial data signal output to system control IC.
Serial data signal input from system control IC.
Command/parameter discrimination signal input from system control IC.
(L: command transmission, H: parameter transmission)
13
SI
I
14
DVDD
—
Power supply pin (+3.3 V)
15
DAVDD
—
D/A converter power supply (+) pin (+3.3 V)
16
ROUT
O
Analog audio signal output (R-ch)
17
DAGND
—
Ground pin
18
REGC
—
Capacitor connection pin for SCF regulator.
19
DAGND
—
Ground pin
20
LOUT
O
Analog audio signal output (L-ch)
21
DAVDD
—
D/A converter power supply (+) pin (+3.3 V)
22
XVDD
—
Power supply pin (+3.3 V)
23
XTAL
O
Main system clock output (16.9344 MHz)
Main system clock input (16.9344 MHz)
24
XTAL
I
25
XGND
—
Ground pin
26
DVDD
—
Power supply pin (+3.3 V)
27
C1D1/FZD
O
Not used. (Open)
28
C1D2/TZD
O
Not used. (Open)
29
C2D1/RMUTE
O
CD R-ch data zero detection signal output
30
C2D2/LMUTE
O
CD L-ch data zero detection signal output
31
C2D3/SHOCK/SBSY
O
Not used. (Open)
32
LOCK/FR
O
Not used. (Open)
33
WFCK/MIRR
O
Not used. (Open)
34
RFCK/HOLD
O
Not used. (Open)
35
PLCK
O
Not used. (Open)
36
C16M
O
Not used. (Open)
37
DGND
—
Ground pin
38
TX
O
Not used. (Open)
39
EMPH/RAMOVER
O
Not used. (Open)
40
FLAG
O
Not used. (Open)
41
DVDD
—
42
LIMIT
I
43
XTALEN
I
44
DGND
—
Power supply pin (+3.3 V)
Not used. (Fixed at L in this set.)
Oscillation circuit ON/OFF control signal input (L: ON, H: OFF)
(Fixed at L in this set.)
Ground pin
45
DIN
I
Not used. (Connect to DOUT in this set.)
46
DOUT
O
Not used. (Connect to DIN in this set.)
27
CDX-GT06/CXS-GT06HP
Pin No.
Pin Name
I/O
47
SCKIN
I
Pin Description
48
SCKO
O
Not used. (Connect to SCKIN in this set.)
49
LRCKIN
I
Not used. (Connect to LRCK in this set.)
Not used. (Connect to SCKO in this set.)
50
LRCK
O
Not used. (Connect to LRCKIN in this set.)
51
DVDD
—
Power supply pin (+3.3 V)
52
FD+
O
Focus servo drive PWM signal output (+)
53
FD–
O
Focus servo drive PWM signal output (–)
54
TD+
O
Tracking servo drive PWM signal output (+)
55
TD–
O
Tracking servo drive PWM signal output (–)
56
SD+
O
Sled servo drive PWM signal output (+)
57
SD–
O
Sled servo drive PWM signal output (–)
58
MD+
O
Spindle servo drive PWM signal output (+)
59
MD–
O
Spindle servo drive PWM signal output (–)
60
DGND
—
Ground pin
61
TESTEN
I
62 to 66
TEST4 to TEST0
I
67
ADGND
—
A/D converter power supply (–) pin
68
EFM
O
EFM signal output
28
Test setting input (Fixed at L in this set.)
Test setting input (Fixed at L in this set.)
69
ASY
I
EFM comparator reference voltage input
70
ADVDD
—
A/D converter power supply pin (+3.3 V)
71
RFI
I
72
EQ2
—
RF signal input for EFM data growing.
73
EQ1
—
74
RF–
I
Not used. (Open)
75
RF2–
I
RF amplifier inversion input
76
AGCO
O
RF signal output after on AGC.
77
AGCI
I
RF AGC signal amplifier input
78
RFO
O
RF signal output before on AGC.
79
ATEST
I
Not used. (Open)
Not used. (Open)
RF amplifier equalizer parts connection pin
80
C3T
—
Capacitor connection pin for 3T detection.
81
AGND
—
Ground pin
82
A
I
Signal input (A) from optical pick-up detector.
83
C
I
Signal input (C) from optical pick-up detector.
84
B
I
Signal input (B) from optical pick-up detector.
85
D
I
Signal input (D) from optical pick-up detector.
86
F
I
Signal input (F) from optical pick-up detector.
87
E
I
Signal input (E) from optical pick-up detector.
88
VREFIN
I
Reference voltage (+1.65 V) input
89
AVDD
—
Analog power supply pin (+3.3 V)
90
REFOUT
O
Reference voltage (+1.65 V) output
91
REFC
—
Capacitor connection pin for reference voltage output.
92
FE–
I
Focus error signal amplifier inversion input
93
FEO
O
Focus error signal amplifier output
94
ADCIN
I
Not used. (Open)
95
TE–
I
Tracking error signal amplifier inversion input
96
TEO
O
Tracking error signal amplifier before output
97
TE2
O
Tracking error signal amplifier after output
98
TEC
I
Tracking error signal comparator input
99
AGND
—
100
PWMSW
I
Ground pin
Not used. (Fixed at L in this set.)
CDX-GT06/CXS-GT06HP
IC501 MB90488BPF-G-186-AE1 (SYSTEM CONTROL) (MAIN BOARD (3/3))
Pin No.
Pin Name
I/O
Pin Description
1
AREASEL2
I
Destination setting pin
2
AREASEL1
I
Destination setting pin
3
AREASEL0
I
Destination setting pin
4
COL SW
I
Illumination color select signal input
5
BEEP
O
Beep signal output
6
CYRIL SEL
I
Cyril select signal input
7
NOSE SW
I
Front panel open/close detect signal input
8
DIAG
I
Power AMP status signal input
9
VOL ATT
O
Electronic volume attenuate control signal output
10
NCO
O
Not used. (Open)
11
VSS
—
Ground pin
12
TU ATT
O
Tuner mute control signal output
13
NS MASK
O
Noise mask signal output
14
ILLUMI SEL1
I
Illumination voltage setting signal input 1
15
ILLUMI SEL2
I
Illumination voltage setting signal input 2
16, 17
NCO
O
Not used. (Open)
18
CD SI
I
CD servo serial data signal input
Not used in this set. (Open)
Not used in this set.
Not used in this set. (Open)
19
CD SO
O
CD servo serial data signal output
20
CD SCK
O
CD servo serial clock signal output
21, 22
NCO
O
Not used. (Open)
23
VCC5
—
Power supply pin (+3.3 V)
24
EEP SIO
I/O
EEPROM bus serial data input/output
25
EEP CKO
O
EEPROM bus serial clock output
26
AMP STB
O
Power AMP standby signal output
27
LCD CE
O
LCD driver chip enable signal output
28
LCD SO
O
LCD driver serial data signal output
29
LCD CKO
O
LCD driver serial clock signal output
30
RDS ON
O
RDS ON signal output
31
RE IN0
I
Rotary encoder signal input 0
Not used in this set. (Open)
32
RE IN1
I
Rotary encoder signal input 1
33
I2C CKO
O
I2C bus serial clock signal output
34
I2C SIO
I/O
I2C bus serial data signal input/output
35
DAVDD
—
A/D converter power supply pin (+3.3 V)
36
AVRH
—
A/D converter external reference power supply pin (+3.3 V)
37
DAVSS
—
Ground pin
38
QUALITY
I
Noise detect signal input
39
VSM
I
S-meter voltage detect signal input
40
KEY IN1
I
Key signal input 1
41
KEY IN0
I
Key signal input 0
42
VSS
—
43
RC IN0
I
Rotary commander key signal input
44 to 48
NCO
O
Not used. (open)
49
MD0
I
Operation mode setting pin (Connect to VDD.)
50
MD1
I
Operation mode setting pin (Connect to VDD.)
51
MD2
I
Operation mode setting pin (Connect to VSS.)
52
KEY ACK
I
Key acknowledgment detect signal input
53
TU ATT IN
I
Tuner mute zero cross detect signal input
54
BU IN
I
Back-up power supply detect signal input
55
CD INTQ
I
CD servo text pack synchronization signal input
Not used in this set.
Ground pin
29
CDX-GT06/CXS-GT06HP
Pin No.
Pin Name
I/O
56
DAVN
I
RDS data block synchronized detect signal input
Pin Description
57
NCO
O
Not used. (Open)
58
UNISI
I
SONY bus data signal input
59
UNI SO
O
SONY bus data signal output
60
UNI SCK
O
SONY bus clock signal output
61
611 SEL
I
Mechanism deck select signal input
62
WMA
I
WMA select signal input
63
NCO
O
Not used. (Open)
Not used in this set.
Not used in this set. (Open)
Not used in this set.
Not used in this set. (Open)
Not used in this set. (Open)
64
SIRCS
I
Remote control signal input
65 to 67
NCO
O
Not used. (Open)
Not used in this set.
68
FLASH W
I
Memory mode select signal input
69, 70
NCO
O
Not used. (Open)
71
RC IN1
I
Rotary commander shift key signal input
72
ACC IN
I
Accessory power supply detect signal input
73
TEST IN
I
Test mode detect signal input
74
TEL ATT
I
Telephone attenuate detect signal input
75
NCO
O
Not used. (Open)
76
XKEY ON
O
A/D converter power supply control signal output
77
RESET
I
CPU reset signal input
78
NCO
O
Not used. (Open)
79
XOUT
O
Sub-clock output (32.768 kHz)
80
XIN
I
Sub-clock input (32.768 kHz)
81
VSS1
—
82
OSC IN
I
Main-clock input (18.432 MHz)
83
OSC OUT
O
Main-clock output (18.432 MHz)
84
VCC3
—
Power supply pin (+3.3 V)
85
DEMOSEL
I
DEMO select signal input
86
ATT
O
Audio mute control signal output
87
BUS ON
O
Bus on signal output
30
Not used in this set.
Not used in this set.
Not used in this set.
Not used in this set.
Ground pin
88
SYS RST
O
System reset signal output
89
CD RFOK
O
Shutter open information signal output to CD mechanism
90
CD RST
O
CD servo reset signal output
91
CD A0
O
CD servo command/parameter signal output
92
CD STB
O
CD servo data strob signal output
93
CD MUTE R
I
CD mechanism zero cross mute detect signal input R
94
CD MUTE L
I
CD mechanism zero cross mute detect signal input L
95
CD INSW
I
CD mechanism disc in switch detect signal input
96
CD SELFSW
I
CD self switch signal input
97
CD LM LO
O
CD mechanism loading motor (+6 V) control signal output
98
CD LM EJ
O
CD mechanism eject motor control signal output
99
CD DSW
I
CD mechanism disc in switch detect signal input
100
CD LIMIT
I
CD mechanism limit switch detect signal input
CDX-GT06/CXS-GT06HP
SECTION 4
EXPLODED VIEWS
NOTE:
• The mechanical parts with no reference
number in the exploded views are not supplied.
• Items marked “*” are not stocked since
they are seldom required for routine service.
Some delay should be anticipated
when ordering these items.
• -XX and -X mean standardized parts, so
they may have some difference from the
original one.
4-1.
•
•
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
Color Indication of Appearance Parts
Example :
KNOB, BALANCE (WHITE) ... (RED)
R
R
Parts Color Cabinet’s Color
Accessories are given in the last of this parts list.
MAIN SECTION
A
MG-611XE-186//C
#2
#1
not supplied
A
8
B
FU601
5
#3
4
6
7
3
#1
TU1
not supplied
B
2
#1
not supplied
#1
1
Ref. No.
Part No.
Description
1
2
3
4
5
X-2067-566-1
2-583-939-01
X-2055-203-2
3-246-006-31
2-583-940-01
PANEL ASSY, SUB
SCREW (+B 2X4)
LOCK ASSY (S)
COVER
SCREW +BTT 2.6X5
6
7
A-1206-054-A MAIN BOARD, COMPLETE
2-345-298-01 PLATE (TU), GROUND
Remark
Ref. No.
Part No.
Description
8
FU601
TU1
#1
#2
1-776-206-21
1-532-877-11
A-3220-961-B
7-685-792-09
7-685-790-01
CORD (WITH CONNECTOR) (POWER)
FUSE (BLADE TYPE) (AUTO FUSE) 10A
TUNER UNIT (TUX-032)
SCREW +PTT 2.6X6 (S)
SCREW +PTT 2.6X4 (S)
#3
7-685-793-09 SCREW +PTT 2.6X8 (S)
Remark
31
CDX-GT06/CXS-GT06HP
4-2.
FRONT PANEL SECTION
63
not supplied
(KEY board)
63
RE901
58
61
LCD901
62
59
57
not supplied
56
not
supplied
not supplied
not supplied
51
not supplied
55
53
52
not supplied
(JACK board)
54
60
Ref. No.
Part No.
Description
51
52
53
54
55
X-2067-579-1
X-2149-325-1
2-631-526-11
A-1206-099-A
X-2102-729-1
BUTTON ASSY (S)
PANEL SUB ASSY, FRONT
PLATE (CD), LIGHT GUIDE
PANEL ASSY, FRONT
KNOB (VOL) (SV) ASSY
56
57
58
2-349-626-01 SPRING (RELEASE)
1-780-199-11 CONDUCTIVE BOARD, CONNECTION
2-634-438-01 ILLUMINATOR (LCD)
32
Remark
Ref. No.
59
60
61
62
63
Part No.
Description
X-2067-569-1
3-251-320-01
2-631-511-04
3-040-315-01
3-250-543-91
HOLDER (LCD) ASSY
EMBLEM (NO. 2.5), SONY
PANEL, FRONT BACK
COVER (AC OUT)
SCREW (+B P-TITE M2)
Remark
LCD901 1-805-920-11 DISPLAY PANEL, LIQUID CRYSTAL
RE901 1-478-474-12 ENCODER, ROTARY (PUSH SELECT/VOLUME)
CDX-GT06/CXS-GT06HP
4-3.
CD MECHANISM SECTION (1)
(MG-611XE-186//C)
not supplied
(SENSOR board)
101
not supplied
#4
not supplied
not supplied
not supplied
103
104
106
105
102
107
Ref. No.
101
102
103
104
Part No.
Description
A-1088-624-A
A-1083-497-A
2-345-865-11
2-345-865-01
CHASSIS (T) SUB ASSY
SERVO BOARD, COMPLETE
SPRING (DAMPER), COMPRESSION (BLACK)
SPRING (DAMPER), COMPRESSION (NATURAL)
Remark
Ref. No.
105
106
107
#4
Part No.
Description
2-345-767-21
3-253-748-11
3-352-758-31
7-627-552-87
SPRING (KF60), TENSION
DAMPER (S)
SCREW (M1.7X2.5), TOOTHED LOCK
SCREW, PRECISION +P 1.7X2.2
Remark
33
CDX-GT06/CXS-GT06HP
4-4.
CD MECHANISM SECTION (2)
(MG-611XE-186//C)
155
156
157
154
(including M901)
#5
M902
160
SW4
159
158
not supplied
153
not supplied
151
152
Ref. No.
Part No.
Description
151
152
0 153
154
155
A-1088-612-A
3-316-938-91
8-820-207-12
A-1088-615-A
A-1088-616-A
CHASSIS (OP) COMPLETE ASSY
SCREW (B1.4X5), TAPPING
OPTICAL PICK-UP (KSS1000E/K1RP)
CHASSIS (OP) SUB ASSY (including M901)
ARM SUB ASSY, CHUCKING
156
157
34
A-1088-613-A LEVER (SL) SUB ASSY
X-2024-784-3 LEVER (SL) ASSY
Remark
Ref. No.
Part No.
Description
158
159
160
M902
SW4
3-261-959-21
3-253-736-21
3-253-742-21
A-1088-614-A
1-786-339-11
SPRING (SL), TORSION
SPRING (CHKG), TENSION
WHEEL (SL), WORM
MOTOR ASSY, SL (SLED)
SWITCH (M) (LIMIT)
#5
7-627-850-77 SCREW, PRECISION +P 1.4X1.8
Remark
CDX-GT06/CXS-GT06HP
4-5.
CD MECHANISM SECTION (3)
(MG-611XE-186//C)
203
201
202
207
211
204
209
208
210
205
207
207
M903
#4
206
Ref. No.
Part No.
Description
201
202
203
204
205
3-262-755-11
2-186-699-21
A-1088-618-A
3-259-455-21
3-253-713-21
WASHER (1.1-2.5)
GEAR (RA1)
ARM ASSY, ROLLER
SPRING (RAL)
SPRING (RAR)
206
207
3-259-469-21 SPRING (LE), LEAF
2-134-636-51 SCREW (M1.7X2.5)
Remark
Ref. No.
Part No.
Description
208
209
210
211
M903
2-186-696-22
3-345-648-91
A-1088-623-A
2-186-697-21
A-1088-622-A
BRACKET (LEM-N)
SCREW (M1.4), TOOTHED LOCK
GEAR (LE) ASSY
BEARING (LEB-N)
MOTOR ASSY, LE (LOADING)
#4
7-627-552-87 SCREW, PRECISION +P 1.7X2.2
Remark
35
CDX-GT06/CXS-GT06HP
4-6.
CD MECHANISM SECTION (4)
(MG-611XE-186//C)
253
256
254
251
252
255
Ref. No.
251
252
253
36
Part No.
Description
2-186-700-21 GEAR (CHK1)
3-259-470-24 GEAR (LE1)
3-253-755-23 LEVER (D)
Remark
Ref. No.
254
255
256
Part No.
Description
2-590-545-22 GEAR (LE2-M)
A-1088-620-A CHASSIS (M) BLOCK ASSY
3-262-755-11 WASHER (1.1-2.5)
Remark
CDX-GT06/CXS-GT06HP
SECTION 5
ELECTRICAL PARTS LIST
NOTE:
• Due to standardization, replacements in
the parts list may be different from the
parts specified in the diagrams or the
components used on the set.
• -XX and -X mean standardized parts, so
they may have some difference from the
original one.
• RESISTORS
All resistors are in ohms.
METAL:Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F:nonflammable
Ref. No.
Part No.
•
•
•
•
Items marked “*” are not stocked since
they are seldom required for routine service.
Some delay should be anticipated
when ordering these items.
SEMICONDUCTORS
In each case, u : µ, for example:
uA.. : µA.. uPA.. : µPA..
uPB.. : µPB.. uPC.. : µPC.. uPD.. : µPD..
CAPACITORS
uF : µF
COILS
uH : µH
Description
Remark
Ref. No.
Part No.
JACK BOARD
***********
J901
1-819-732-11 JACK (DIA. 3.5) (AUX)
*************************************************************
KEY BOARD
**********
< CAPACITOR >
C921
C922
C981
C983
C984
1-163-031-11
1-163-031-11
1-107-826-11
1-107-826-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
0.1uF
0.1uF
0.1uF
10%
10%
10%
50V
50V
16V
16V
16V
C985
C986
1-131-664-11 CERAMIC CHIP
1-127-715-11 CERAMIC CHIP
0.15uF
0.22uF
10%
10%
10V
16V
< CONNECTOR >
DIODE
DIODE
DIODE
DIODE
0
0
0
6-707-063-01 IC LC75826WH-US-E
< DIODE >
LED932 6-501-339-01 LED NESW505CT-AST (LCD BACK LIGHT)
< RESISTOR >
LED951 1-216-810-11 METAL CHIP
Remark
1-786-806-12
1-786-806-12
1-786-806-12
1-786-806-12
1-786-806-12
SWITCH, TACTILE (WITH LED) (Z)
SWITCH, TACTILE (WITH LED) (OFF)
SWITCH, TACTILE (WITH LED) (SOURCE)
SWITCH, TACTILE (WITH LED) (EQ3)
SWITCH, TACTILE (WITH LED)
(M > SEEK +)
LSW915
LSW916
LSW917
LSW918
LSW919
1-786-806-12
1-786-806-12
1-786-806-12
1-786-806-12
1-786-806-12
SWITCH, TACTILE (WITH LED) (3/REP)
SWITCH, TACTILE (WITH LED) (4/SHUF)
SWITCH, TACTILE (WITH LED) (5)
SWITCH, TACTILE (WITH LED) (6)
SWITCH, TACTILE (WITH LED) (SENS)
120
8-729-027-44 TRANSISTOR DTC114TKA-T146
8-729-027-58 TRANSISTOR DTC143ZKA-T146
< RESISTOR >
< IC >
IC901
Description
LSW910 1-786-806-12 SWITCH, TACTILE (WITH LED)
(. m SEEK –)
LSW911 1-786-806-12 SWITCH, TACTILE (WITH LED) (BTM)
LSW912 1-786-806-12 SWITCH, TACTILE (WITH LED) (MODE)
LSW913 1-786-806-12 SWITCH, TACTILE (WITH LED) (1)
LSW914 1-786-806-12 SWITCH, TACTILE (WITH LED) (2)
Q931
Q932
RSA6.1ENTR
UDZW-TE17-18B
UDZW-TE17-5.1B
1SS355WTE-17
1-216-864-11 SHORT CHIP
1-216-864-11 SHORT CHIP
1-216-295-11 SHORT CHIP
When indicating parts by reference
number, please include the board.
< TRANSISTOR >
< JUMPER RESISTOR >
FB901
FB902
FB903
LSW901
LSW902
LSW903
LSW908
LSW909
1-819-758-12 PLUG, CONNECTOR 15P
6-500-886-01
6-501-180-01
6-501-167-01
6-501-193-01
The components identified by
mark 0 or dotted line with mark.
0 are critical for safety.
Replace only with part number
specified.
LSW920 1-786-806-12 SWITCH, TACTILE (WITH LED) (DSPL/DIM)
< DIODE >
D901
D903
D981
D982
KEY
< SWITCH >
< JACK >
CN901
JACK
5%
1/10W
R901
R902
R903
R904
R905
1-216-819-11
1-216-819-11
1-216-819-11
1-216-821-11
1-216-823-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
680
680
680
1K
1.5K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R906
R907
R908
R909
R910
1-216-819-11
1-216-819-11
1-216-819-11
1-216-821-11
1-216-823-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
680
680
680
1K
1.5K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R911
R912
R913
R914
R915
1-216-823-11
1-216-825-11
1-216-827-11
1-216-829-11
1-218-867-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1.5K
2.2K
3.3K
4.7K
6.8K
5%
5%
5%
5%
0.5%
1/10W
1/10W
1/10W
1/10W
1/10W
R916
R917
R918
R921
1-216-833-11
1-216-835-11
1-216-837-11
1-216-025-11
METAL CHIP
METAL CHIP
METAL CHIP
RES-CHIP
10K
15K
22K
100
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
37
CDX-GT06/CXS-GT06HP
KEY
Ref. No.
MAIN
Part No.
Description
Part No.
Description
R922
R931
R932
R933
R934
1-216-025-11
1-216-812-11
1-216-812-11
1-216-812-11
1-216-822-11
RES-CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
180
180
180
1.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
Remark
C401
C404
C405
C406
C407
1-126-964-11
1-127-715-11
1-127-715-11
1-126-960-11
1-126-960-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
10uF
0.22uF
0.22uF
1uF
1uF
20%
10%
10%
20%
20%
50V
16V
16V
50V
50V
R941
R942
R943
R944
R945
1-216-810-11
1-216-810-11
1-216-810-11
1-216-811-11
1-216-810-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
120
120
120
150
120
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
C410
C411
C412
C413
C431
1-162-923-11
1-162-923-11
1-126-934-11
1-162-970-11
1-126-964-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
47PF
47PF
220uF
0.01uF
10uF
5%
5%
20%
10%
20%
50V
50V
16V
25V
50V
R946
R947
R948
R949
R950
1-216-807-11
1-216-807-11
1-216-811-11
1-216-810-11
1-216-807-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
68
68
150
120
68
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
C432
C435
C441
C442
C445
1-165-908-11
1-165-908-11
1-126-964-11
1-165-908-11
1-165-908-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
1uF
1uF
10uF
1uF
1uF
10%
10%
20%
10%
10%
10V
10V
50V
10V
10V
R951
R952
R953
R954
R955
1-216-807-11
1-216-810-11
1-216-811-11
1-216-810-11
1-216-811-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
68
120
150
120
150
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
C451
C452
C455
C461
C462
1-126-964-11
1-165-908-11
1-165-908-11
1-126-964-11
1-165-908-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
10uF
1uF
1uF
10uF
1uF
20%
10%
10%
20%
10%
50V
10V
10V
50V
10V
R956
R957
R958
R974
R976
1-216-810-11
1-216-811-11
1-216-810-11
1-216-864-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
SHORT CHIP
120
150
120
0
0
5%
5%
5%
1/10W
1/10W
1/10W
C465
C471
C474
C479
C481
1-165-908-11
1-126-964-11
1-163-251-11
1-126-947-11
1-126-964-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
ELECT
1uF
10uF
100PF
47uF
10uF
10%
20%
5%
20%
20%
10V
50V
50V
35V
50V
R977
R978
R979
R981
R982
1-216-809-11
1-216-809-11
1-216-809-11
1-216-811-11
1-216-811-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
150
150
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
C484
C501
C502
C503
C504
1-163-251-11
1-162-970-11
1-162-964-11
1-104-665-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
100PF
0.01uF
0.001uF
100uF
0.01uF
5%
10%
10%
20%
10%
50V
25V
50V
25V
25V
C507
C508
C509
C510
C511
1-162-917-11
1-162-917-11
1-162-966-11
1-162-970-11
1-104-665-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
15PF
15PF
0.0022uF
0.01uF
100uF
5%
5%
10%
10%
20%
50V
50V
50V
25V
25V
C512
C513
C514
C516
C519
1-162-964-11
1-162-964-11
1-162-964-11
1-216-864-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
SHORT CHIP
CERAMIC CHIP
0.001uF
0.001uF
0.001uF
0
0.1uF
10%
10%
10%
50V
50V
50V
10%
16V
C601
C602
C617
C618
C622
1-131-868-81
1-165-319-11
1-163-009-11
1-163-009-11
1-126-916-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
3300uF
0.1uF
0.001uF
0.001uF
1000uF
20%
10%
10%
20%
16V
50V
50V
50V
6.3V
C623
C631
C750
C751
C753
1-126-916-11
1-126-960-11
1-115-340-11
1-115-340-11
1-128-551-11
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
1000uF
1uF
0.22uF
0.22uF
22uF
20%
20%
10%
10%
20%
6.3V
50V
25V
25V
63V
C754
C755
C756
C758
C763
1-126-961-11
1-162-964-11
1-127-715-11
1-126-964-11
1-127-715-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
2.2uF
0.001uF
0.22uF
10uF
0.22uF
20%
10%
10%
20%
10%
50V
50V
16V
50V
16V
C764
C765
C769
1-115-340-11 CERAMIC CHIP
1-115-340-11 CERAMIC CHIP
1-127-715-11 CERAMIC CHIP
0.22uF
0.22uF
0.22uF
10%
10%
10%
25V
25V
16V
R984
1-216-821-11 METAL CHIP
1K
5%
1/10W
R985
1-216-821-11 METAL CHIP
1K
5%
1/10W
R986
1-216-821-11 METAL CHIP
1K
5%
1/10W
R987
1-216-857-11 METAL CHIP
1M
5%
1/10W
R991
1-216-864-11 SHORT CHIP
0
*************************************************************
A-1206-054-A MAIN BOARD, COMPLETE
*********************
7-621-284-40
7-685-134-19
7-685-793-09
7-685-795-09
SCREW +P 2.6X10
SCREW +P 2.6X8 TYPE2 NON-SLIT
SCREW +PTT 2.6X8 (S)
SCREW +PTT 2.6X12 (S)
< CAPACITOR >
C4
C5
C6
C7
C12
1-126-947-11
1-126-947-11
1-162-970-11
1-162-970-11
1-162-970-11
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
47uF
47uF
0.01uF
0.01uF
0.01uF
20%
20%
10%
10%
10%
35V
35V
25V
25V
25V
C13
C301
C302
C303
C305
1-162-970-11
1-128-551-11
1-104-665-11
1-128-551-11
1-104-665-11
CERAMIC CHIP
ELECT
ELECT
ELECT
ELECT
0.01uF
22uF
100uF
22uF
100uF
10%
20%
20%
20%
20%
25V
63V
25V
63V
25V
C306
C307
C308
C343
1-162-970-11
1-162-970-11
1-162-970-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
0.01uF
0.01uF
10%
10%
10%
10%
25V
25V
25V
25V
38
Ref. No.
Remark
CDX-GT06/CXS-GT06HP
MAIN
Ref. No.
Part No.
Description
C770
C771
C774
C775
C776
1-127-715-11
1-127-715-11
1-115-340-11
1-115-340-11
1-162-964-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.22uF
0.22uF
0.22uF
0.22uF
0.001uF
10%
10%
10%
10%
10%
16V
16V
25V
25V
50V
Remark
C901
C902
C903
C905
C917
1-109-982-11
1-109-982-11
1-126-961-11
1-162-970-11
1-163-017-00
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
1uF
1uF
2.2uF
0.01uF
0.0047uF
10%
10%
20%
10%
10%
10V
10V
50V
25V
50V
C918
1-163-017-00 CERAMIC CHIP
0.0047uF 10%
50V
Ref. No.
FB605
FB606
Part No.
Description
Remark
1-216-864-11 SHORT CHIP
1-216-864-11 SHORT CHIP
0
0
< FUSE >
FU601
1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) 10A
< IC >
IC401
IC501
IC602
IC750
IC901
6-708-880-01
6-806-757-01
8-759-659-13
6-705-363-02
8-759-681-42
IC
IC
IC
IC
IC
BD3806AFS-E2
MB90488BPF-G-186-AE1
PST3428UL
TDA8589BJ/N2/R1
NJM12902V(TE2)
< CONNECTOR >
< JACK >
CN601 1-774-701-21 PIN, CONNECTOR 16P
CN701 1-819-773-13 SOCKET, CONNECTOR 15P
CNP301 1-817-536-11 CONNECTOR, BOARD TO BOARD 28P
J1
J330
1-815-185-13 JACK (ANTENNA)
1-774-698-11 JACK, PIN 2P (AUDIO OUT REAR L/R)
< DIODE >
< JUMPER RESISTOR >
D1
D479
D503
D580
D581
6-501-168-01
6-501-193-01
6-501-193-01
6-501-171-01
6-501-180-01
DIODE
DIODE
DIODE
DIODE
DIODE
UDZW-TE17-5.6B
1SS355WTE-17
1SS355WTE-17
UDZW-TE17-7.5B
UDZW-TE17-18B
JC1
JC501
JC504
JC534
JC536
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
D601
D609
D617
D704
D719
8-719-049-38
6-501-170-01
6-501-180-01
1-216-295-11
6-501-180-01
DIODE 1N5404TU
DIODE UDZW-TE17-6.8B
DIODE UDZW-TE17-18B
SHORT CHIP
0
DIODE UDZW-TE17-18B
JC681
JC753
JC754
JC755
JC756
1-216-864-11
1-216-296-11
1-216-296-11
1-216-296-11
1-216-864-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
D751
D752
D753
D754
D755
6-500-522-01
6-500-522-01
6-500-522-01
6-500-522-01
6-500-522-01
DIODE
DIODE
DIODE
DIODE
DIODE
10EDB40-TA1B2
10EDB40-TA1B2
10EDB40-TA1B2
10EDB40-TA1B2
10EDB40-TA1B2
JC795
1-216-864-11 SHORT CHIP
0
D756
D757
D758
D759
D760
6-500-522-01
6-500-522-01
6-500-522-01
6-500-522-01
6-500-522-01
DIODE
DIODE
DIODE
DIODE
DIODE
10EDB40-TA1B2
10EDB40-TA1B2
10EDB40-TA1B2
10EDB40-TA1B2
10EDB40-TA1B2
D761
D762
D903
6-500-522-01 DIODE 10EDB40-TA1B2
6-500-522-01 DIODE 10EDB40-TA1B2
6-501-170-01 DIODE UDZW-TE17-6.8B
< COIL >
L1
L301
L501
L601
1-469-844-11
1-216-295-11
1-216-295-11
1-456-617-11
INDUCTOR
SHORT CHIP
SHORT CHIP
COIL, CHOKE
2.2uH
0
0
< TRANSISTOR >
Q1
Q431
Q441
Q451
Q461
6-551-431-01
8-729-027-44
8-729-027-44
8-729-027-44
8-729-027-44
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC6027T100-QR
DTC114TKA-T146
DTC114TKA-T146
DTC114TKA-T146
DTC114TKA-T146
Q471
Q478
Q479
Q481
Q580
6-551-392-01
1-801-806-11
8-729-027-23
6-551-392-01
8-729-027-43
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
RT6N140C-TP-1
DTC144EKA
DTA114EKA-T146
RT6N140C-TP-1
DTC114EKA-T146
Q581
Q582
Q631
Q664
1-801-806-11
8-729-120-28
8-729-120-28
8-729-027-23
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC144EKA
2SC1623-L5L6
2SC1623-L5L6
DTA114EKA-T146
< FERRITE BEAD >
FB1
FB301
FB302
FB303
FB304
1-500-245-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-295-11
INDUCTOR, FERRITE BEAD
SHORT CHIP
0
SHORT CHIP
0
SHORT CHIP
0
SHORT CHIP
0
FB305
FB306
FB307
FB310
FB311
1-216-295-11
1-216-295-11
1-216-864-11
1-216-864-11
1-216-864-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
FB410
FB411
FB501
FB603
FB604
1-216-864-11
1-216-864-11
1-216-295-11
1-216-295-11
1-500-245-11
SHORT CHIP
0
SHORT CHIP
0
SHORT CHIP
0
SHORT CHIP
0
INDUCTOR, FERRITE BEAD
0
0
0
0
0
< RESISTOR >
R1
R2
R3
R4
R5
1-216-821-11
1-414-595-11
1-414-595-11
1-216-839-11
1-216-843-11
METAL CHIP
1K
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
METAL CHIP
33K
METAL CHIP
68K
5%
1/10W
5%
5%
1/10W
1/10W
39
CDX-GT06/CXS-GT06HP
MAIN
Ref. No.
Part No.
Description
R12
R13
R301
R302
R401
1-414-595-11
1-414-595-11
1-216-821-11
1-216-821-11
1-216-797-11
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
METAL CHIP
1K
METAL CHIP
1K
METAL CHIP
10
Part No.
Description
1-216-845-11
1-216-864-11
1-216-845-11
1-216-845-11
1-216-821-11
METAL CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
0
100K
100K
1K
5%
1/10W
1/10W
1/10W
1/10W
R538
R539
R540
R541
R543
5%
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
R405
R406
R407
R408
R409
1-218-881-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
27K
100
100
100
100
0.5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R544
R550
R551
R556
R557
1-216-821-11
1-216-845-11
1-216-845-11
1-216-833-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
100K
100K
10K
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R410
R411
R431
R432
R441
1-216-809-11
1-216-809-11
1-216-821-11
1-216-833-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
1K
10K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R558
R559
R560
R561
R563
1-216-821-11
1-216-845-11
1-216-845-11
1-216-845-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
100K
100K
100K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R442
R451
R452
R461
R462
1-216-833-11
1-216-821-11
1-216-833-11
1-216-821-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
1K
10K
1K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R565
R566
R567
R568
R570
1-216-845-11
1-216-845-11
1-216-845-11
1-216-821-11
1-216-817-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
100K
100K
1K
470
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R471
R472
R479
R481
R482
1-216-809-11
1-216-833-11
1-216-805-11
1-216-809-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
10K
47
100
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R571
R572
R575
R577
R582
1-216-845-11
1-216-809-11
1-216-845-11
1-216-845-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
100
100K
100K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R502
R503
R504
R505
R507
1-216-821-11
1-216-821-11
1-218-871-11
1-218-871-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
10K
10K
100K
5%
5%
0.5%
0.5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R583
R584
R585
R601
R609
1-216-821-11
1-216-841-11
1-216-849-11
1-216-845-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
47K
220K
100K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R508
R509
R510
R511
R512
1-216-864-11
1-216-812-11
1-216-821-11
1-216-821-11
1-216-821-11
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
180
1K
1K
1K
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
R631
R632
R633
R634
R636
1-249-425-11
1-216-841-11
1-216-841-11
1-216-829-11
1-216-845-11
CARBON
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
47K
47K
4.7K
100K
5%
5%
5%
5%
5%
1/4W
1/10W
1/10W
1/10W
1/10W
R513
R514
R515
R516
R517
1-216-845-11
1-216-845-11
1-247-807-31
1-247-807-31
1-216-841-11
METAL CHIP
METAL CHIP
CARBON
CARBON
METAL CHIP
100K
100K
100
100
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/4W
1/4W
1/10W
R661
R662
R663
R664
R671
1-216-821-11
1-216-845-11
1-216-821-11
1-216-845-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
100K
1K
100K
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R518
R519
R521
R522
R523
1-216-825-11
1-216-845-11
1-216-825-11
1-216-825-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.2K
100K
2.2K
2.2K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R672
R673
R674
R675
R676
1-216-809-11
1-216-833-11
1-216-845-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
10K
100K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R524
R525
R526
R527
R528
1-216-821-11
1-216-821-11
1-216-809-11
1-216-821-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
100
1K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R677
R680
R681
R752
R756
1-216-864-11
1-216-821-11
1-216-821-11
1-216-811-11
1-216-841-11
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
1K
1K
150
47K
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
R529
R530
R531
R532
R533
1-216-821-11
1-216-845-11
1-216-845-11
1-216-845-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
100K
100K
100K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R757
R901
R902
R903
R904
1-216-864-11
1-216-817-11
1-216-817-11
1-216-834-11
1-216-834-11
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
470
470
12K
12K
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
R534
R535
R536
1-216-833-11 METAL CHIP
1-216-845-11 METAL CHIP
1-216-845-11 METAL CHIP
10K
100K
100K
5%
5%
5%
1/10W
1/10W
1/10W
R905
R906
R907
1-216-841-11 METAL CHIP
1-216-841-11 METAL CHIP
1-216-845-11 METAL CHIP
47K
47K
100K
5%
5%
5%
1/10W
1/10W
1/10W
40
Remark
Ref. No.
Remark
CDX-GT06/CXS-GT06HP
MAIN
Ref. No.
R910
R911
R912
R913
R914
Part No.
Description
1-216-789-11
1-216-825-11
1-216-864-11
1-216-864-11
1-216-825-11
METAL CHIP
METAL CHIP
SHORT CHIP
SHORT CHIP
METAL CHIP
2.2
2.2K
0
0
2.2K
Remark
Ref. No.
Part No.
Description
5%
5%
1/10W
1/10W
5%
1/10W
C73
C74
C75
C76
C77
1-162-962-11
1-107-826-11
1-107-826-11
1-162-970-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
C78
C79
1-164-227-11 CERAMIC CHIP
1-164-227-11 CERAMIC CHIP
< SWITCH >
S702
SENSOR
SERVO
Remark
470PF
0.1uF
0.1uF
0.01uF
0.01uF
10%
10%
10%
10%
10%
50V
16V
16V
25V
25V
0.022uF
0.022uF
10%
10%
25V
25V
1-786-826-11 SWITCH, TACTILE (RESET)
< CONNECTOR >
< TUNER UNIT >
TU1
CN1
CN2
A-3220-961-B TUNER UNIT (TUX-032)
1-817-275-21 CONNECTOR, BOARD TO BOARD 28P
1-815-016-61 CONNECTOR, FFC/FPC (ZIF) 16P
< VIBRATOR >
< FERRITE BEAD >
X501
1-813-524-21 VIBRATOR, CERAMIC (18.432MHz)
X502
1-813-202-11 VIBRATOR, CRYSTAL (32.768kHz)
*************************************************************
FB1
FB2
FB3
1-216-864-11 SHORT CHIP
0
1-414-760-21 FERRITE, EMI (SMD) (1608)
1-414-760-21 FERRITE, EMI (SMD) (1608)
SENSOR BOARD
*************
< IC >
IC1
IC2
< SWITCH >
SW2
1-529-566-61 SWITCH, PUSH (1 KEY) (SELF)
SW3
1-529-566-61 SWITCH, PUSH (1 KEY) (DISC IN)
*************************************************************
A-1083-497-A SERVO BOARD, COMPLETE
**********************
6-703-699-01 IC uPD63712GC-8EU-A
6-705-002-01 IC BA5966FP-FE2
< FERRITE BEAD >
JR40
JR41
JR90
JR91
1-414-760-21
1-414-760-21
1-414-760-21
1-414-760-21
< CAPACITOR >
FERRITE, EMI (SMD) (1608)
FERRITE, EMI (SMD) (1608)
FERRITE, EMI (SMD) (1608)
FERRITE, EMI (SMD) (1608)
< TRANSISTOR >
C1
C2
C5
C6
C7
1-107-826-11
1-162-970-11
1-107-826-11
1-100-381-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
0.1uF
0.01uF
0.1uF
10uF
0.1uF
10%
10%
10%
20%
10%
16V
25V
16V
16V
16V
C11
C13
C17
C18
C19
1-107-826-11
1-107-826-11
1-107-826-11
1-162-970-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.01uF
0.1uF
10%
10%
10%
10%
10%
16V
16V
16V
25V
16V
C20
C21
C23
C25
C26
1-107-826-11
1-162-970-11
1-162-923-11
1-162-908-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.01uF
47PF
3PF
0.1uF
10%
10%
5%
0.25PF
10%
16V
25V
50V
50V
16V
C27
C28
C29
C30
C31
1-107-826-11
1-107-826-11
1-107-826-11
1-162-921-11
1-162-925-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
33PF
68PF
10%
10%
10%
5%
5%
16V
16V
16V
50V
50V
C32
C34
C35
C36
C37
1-107-826-11
1-107-826-11
1-107-826-11
1-162-967-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.0033uF
0.01uF
10%
10%
10%
10%
10%
16V
16V
16V
50V
25V
C38
C39
C70
C71
C72
1-104-609-11
1-107-826-11
1-162-965-11
1-162-965-11
1-162-962-11
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100uF
0.1uF
0.0015uF
0.0015uF
470PF
20%
10%
10%
10%
10%
4V
16V
50V
50V
50V
Q1
8-729-904-87 TRANSISTOR 2SB1197K-T-146-R
< RESISTOR >
R1
R2
R3
R4
R5
1-216-841-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
100
100
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R6
R7
R8
R9
R10
1-216-833-11
1-216-840-11
1-414-760-21
1-216-822-11
1-414-760-21
METAL CHIP
10K
5%
METAL CHIP
39K
5%
FERRITE, EMI (SMD) (1608)
METAL CHIP
1.2K
5%
FERRITE, EMI (SMD) (1608)
1/10W
1/10W
R11
R12
R13
R14
R15
1-216-833-11
1-216-809-11
1-216-833-11
1-216-797-11
1-216-797-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R41
R42
R44
R45
R70
1-216-821-11
1-216-821-11
1-414-760-21
1-414-760-21
1-216-842-11
METAL CHIP
1K
5%
METAL CHIP
1K
5%
FERRITE, EMI (SMD) (1608)
FERRITE, EMI (SMD) (1608)
METAL CHIP
56K
5%
1/10W
1/10W
R71
R72
R73
R74
R75
1-216-833-11
1-216-842-11
1-216-833-11
1-216-837-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
56K
10K
22K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R76
1-216-837-11 METAL CHIP
22K
5%
1/10W
10K
100
10K
10
10
1/10W
1/10W
41
CDX-GT06/CXS-GT06HP
SERVO
Ref. No.
Part No.
Description
R77
R78
R79
R80
R81
1-216-833-11
1-216-833-11
1-216-833-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
10K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
Remark
R82
R83
R84
R85
1-216-837-11
1-216-833-11
1-216-837-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
22K
10K
22K
10K
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
< SWITCH >
SW1
1-529-565-61 SWITCH, PUSH (1 KEY) (DOWN)
< VIBRATOR >
X1
1-795-562-21 VIBRATOR, CERAMIC (16.9344MHz)
*************************************************************
Ref. No.
Part No.
Description
Remark
PARTS FOR INSTALLATION AND CONNECTIONS
**************************************
301
302
303
304
305
X-3382-647-1
2-187-743-02
3-246-011-01
3-259-776-01
1-776-206-21
FRAME ASSY, FITTING
COLLAR
KEY (FRAME)
SCREW (+K 5X8 TP)
CORD (WITH CONNECTOR) (POWER)
306
307
308
309
310
2-886-394-01
2-886-389-01
2-886-393-01
2-886-388-01
1-824-847-11
TEMPLATE (for 6X9 in.)
TEMPLATE (for 6 1/2 in.)
GRILLE (for 6X9 in.)
GRILLE (for 6 1/2 in.)
CORD, SPEAKER CONNECTION (0.3m)
311
312
3-240-189-11 SCREW, SPECIAL
2-585-058-01 NUT, SPEED
302
301
303
MISCELLANEOUS
***************
57
0 153
154
LCD901
M902
1-780-199-11
8-820-207-12
A-1088-615-A
1-805-920-11
A-1088-614-A
CONDUCTIVE BOARD, CONNECTION
OPTICAL PICK-UP (KSS1000E/K1RP)
CHASSIS (OP) SUB ASSY (including M901)
DISPLAY PANEL, LIQUID CRYSTAL
MOTOR ASSY, SL (SLED)
×2
304
M903
A-1088-622-A MOTOR ASSY, LE (LOADING)
RE901 1-478-474-12 ENCODER, ROTARY (PUSH SELECT/VOLUME)
SW4
1-786-339-11 SWITCH (M) (LIMIT)
*************************************************************
ACCESSORIES
************
1-826-514-11 SPEAKER (6X9 in.)
1-826-515-11 SPEAKER (6 1/2 in.)
2-886-097-11 MANUAL, INSTRUCTION (ENGLISH,SPANISH)
(CDX-GT06)
2-886-098-11 MANUAL, INSTRUCTION, INSTALL (ENGLISH,
SPANISH) (CXS-GT06HP)
*************************************************************
305
×4
306
307
308
6 × 9 Speaker
Altavoz de 6 × 9
6 1/2 Speaker
Altavoz de 6 1/2
6 × 9 Speaker
Altavoz de 6 × 9
×2
309
310
311
0.3 m (11 7/8 in)
×4
ø4 (3/16 in) × 30 (1 3/16)
× 16
6 1/2 Speaker
Altavoz de 6 1/2
×2
312
× 16
42
CDX-GT06/CXS-GT06HP
MEMO
43
CDX-GT06/CXS-GT06HP
REVISION HISTORY
Clicking the version allows you to jump to the revised page.
Also, clicking the version at the upper on the revised page allows you to jump to the next revised page.
44
Ver.
Date
1.0
2006.07
Description of Revision
New