Download 9927602122015-05-10 13:454.3 MB - Wiki Karat

DP-IF5100
SERVICE MANUAL
US Model
Canadian Model
AEP Model
UK Model
E Model
Ver 1.1 2000. 02
• Manufactured under license from Dolby Laboratories Licensing
SPECIFICATIONS
Corporation.
DOLBY, the double-D symbol ; , “PRO LOGIC”,
“Dolby Digital (AC-3)”, and “VIRTUAL DOLBY DIGITAL” are
trademarks of Dolby Laboratories Licensing Corporation.
Modulation System
Frequency modulation
Carrier wave frequency Right channel 2.8 MHz
Left channel 2.3 MHz
Transmission distance Approx. 10 m to the front
Transmission range
20 – 20,000 Hz
Distortion rate
1% or less (1 kHz)
Audio inputs
Optical input
(rectangular-type) × 1
Analog input (pin jack
left/right) × 1
Power requirements
DC 9 V (from the
supplied AC power
adapter)
Dimensions (w/h/d)
Approx. 85 × 190 × 180
mm (3 3/8 × 7 1/2 × 7 1/8
inch)
Mass
Approx. 1.0 kg
(1000 g) (2 lb 30 oz)
• DP-IF5100 is the component model block one in
MDR-DS5100.
COMPONENT MODEL NAME FOR MDR-DS5100
DIGITAL SURROUND PROCESSOR
DP-IF5100
CORDLESS STEREO HEADPHONES
MDR-IF5000
Design and specifications are subject to
change without notice.
Notes on Chip Component Replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be damaged by heat.
DIGITAL SURROUND PROCESSOR
–1–
TABLE OF CONTENTS
1. GENERAL
Location and Function of Parts ............................................... 3
Listening to the Sound of the Connected Component ............ 3
2. DISASSEMBLY
2-1.
2-2.
2-3.
2-4.
Cover Assy .......................................................................... 5
Panel Assy, Front ................................................................. 5
Panel Assy, Sub ................................................................... 6
TX Board ............................................................................ 6
3. SERVICE MODE
3-1.
3-2.
3-3.
3-4.
General ................................................................................ 7
Setting the Test Mode .......................................................... 7
Releasing the Test Mode ..................................................... 7
Test Mode ............................................................................ 7
4. ELECTRICAL ADJUSTMENTS ................................... 8
5. DIAGRAMS
5-1. IC Pin Descriptions ............................................................. 9
5-1-1. IC201 µPD784216 (Program, System Control) ............ 9
5-1-2. IC301 CXD9511AQ (Dolby Digital (AC-3)/
Pro Logic, DTS Decoder) ............................................ 11
5-1-3. IC302 XCB56362PV100 (24 Bit Audio Digital
Signal Processor) ......................................................... 13
5-2. Block Diagrams ................................................................ 17
5-2-1. Block Diagram –Processor Section– ........................... 17
5-2-2. Block Diagram –Transmitter Section– ........................ 19
5-3. Printed Wiring Boards and Schematic Diagrams .............. 21
5-3-1. Printed Wiring Board –TX Board– ............................. 21
5-3-2. Schematic Diagram –TX Board (1/2)– ....................... 25
5-3-3. Schematic Diagram –TX Board (2/2)– ....................... 27
5-3-4. Printed Wiring Board –LED Board– ........................... 29
5-3-5. Schematic Diagram –LED Board– .............................. 31
5-3-6. Printed Wiring Board –AMP Board– .......................... 33
5-3-7. Schematic Diagram –AMP Board– ............................. 34
5-4. IC Block Diagrams ........................................................... 35
6. EXPLODED VIEW ........................................................... 38
7. ELECTRICAL PARTS LIST ......................................... 39
–2–
SECTION 1
GENERAL
–3–
This section is extracted
from instruction manual.
–4–
SECTION 2
DISASSEMBLY
• The equipment can be removed using the following procedure.
Set
Cover assy
Panel assy, front
Panel assy, sub
TX board
Note : Follow the disassembly procedure in the numerical order given.
2-1. COVER ASSY
5 cover assy
3 PTT 2.6X5
2 PTT 2.6X5
4 PTT 2.6X5
1 PTT 2.6X5
2-2. PANEL ASSY, FRONT
6 P 3X6
8 claws
9 panel assy, front
2 PTT 2.6X5
3 CN102
4 CN103
1 screws (2.6x6)
7 P 3X6
5 CN101
–5–
2-3. PANEL ASSY, SUB
1 P 2X8
2 P 2X8
3 LED board
4 panel assy, sub
2-4. TX BOARD
2 screws BTT
4 TX board
3 screw BTT
1 BVTP 3X8
–6–
SECTION 3
SERVICE MODE
3-1. GENERAL
This set has the test mode of the built-in microprocessor which
allows various check items required repairing.
3-2. SETTING THE TEST MODE
*5) Digital input check : Do not use this in repair.
*6) Analog input check : Other than MUTE check, do not use this
in repair.
*7) Mute mode : Use this in electrical adjustment (see page 8).
*8)
Press the POWER key and the EFFECT key at the same time and
turn on the power. (Insert the DC plug)
C
L
R
HR LED
3-3. RELEASING THE TEST MODE
Remove the DC plug.
LS
3-4. TEST MODE
RS
HL LED
1. LED check
LEDs go on in sequence *1)
POWER,INPUT keys
4. IF test tone
POWER and MUSIC LEDs on
All LEDs on *2)
OUTPUT key
POWER,INPUT keys
All LEDs off *3)
L LED on
1 kHz, –10 dBv
OUTPUT key
Go to Key check
C LED on
*1) In test mode
*2) All infrared LEDs on
*3) All infrared LEDs on
1 kHz, –30 dBv
OUTPUT key
R LED on
2. Key check
100 Hz, –30 dBv
OUTPUT key
Press each key and its corresponding
LED goes on *4)
RS LED on 10 kHz, –30 dBv
POWER,INPUT keys
OUTPUT key
Go to Audio check
LS LED on
*4) Corresponding LEDs
POWER key : POWER LED
INPUT key
: ANALOG LED
EFFECT key : MUSIC LED
OUTPUT key : VIRTUAL LED
1 kHz, FS
OUTPUT key
POWER,INPUT keys
3. Audio check
End of Test mode
POWER, DIGITAL,
L and R LEDs on *5)
POWER,INPUT keys
ANALOG, HR and HL LEDs on *5) *7)
POWER,INPUT keys
HL and HR LEDs off *6)
POWER,INPUT keys
Go to IF test tone
–7–
SECTION 4
ELECTRICAL ADJUSTMENTS
Notes:
1. These adjustments are performed in the order that they are
described.
2. Adjustment and measurement are performed for each channel
unless otherwise specified.
3. Adjustment is made for the right channel first and then the left
channel.
4. The power voltage is supplied with 9 V.
Adjustment Location:
– TX board (side A) –
TP
(A MUTE)
Oscillation Frequency Adjustment
Setting:
digital frequency
counter
LED board
TP03 or TP04 (L-ch)
TP05 or TP06 (R-ch)
+
–
Adjustment method:
• Perform this adjustment without signal.
1. Connect TP (A MUTE) to ground on the TX board (to set the
mute state), or use the test mode to set the mute state (see page
7).
2. Connect a digital frequency counter to TP03 or TP04 for L-ch
and TP05 or TP06 for R-ch on the LED board.
3. Adjust L51 (L-ch) and L1 (R-ch) on the TX board so that the
reading on the digital frequency counter is each within 2.3 MHz
(L-ch) and 2.8 MHz (R-ch).
Specified value:
L-ch
R-ch
L51
L1
– LED board (conductor side) –
TP05
TP06
2.298 to 2.302 MHz
2.798 to 2.802 MHz
RF Level Adjustment
Setting:
digital voltmeter
TP03
LED board
TP03 or TP04 (L-ch)
TP05 or TP06 (R-ch)
+
TP04
–
Adjustment method:
• Perform this adjustment without signal.
1. Connect TP L (L-ch) and TP R (R-ch) to ground on the LED
board (to set the mute state), or use the test mode to set the mute
state (see page 7).
2. Connect a digital voltmeter to TP03 or TP04 for L-ch and TP05
or TP06 for R-ch on the LED board.
3. Adjust RV51 (L-ch) and RV1 (R-ch) on the TX board so that
the reading on the digital voltmeter is 480 mV.
– TX board (side A) –
RV51
Specified value:
L-ch
R-ch
RV51
RV1
RF LEVEL
ADJUSTMENT
RV1
477.5 to 482.5 mV
477.5 to 482.5 mV
L51
L1
–8–
OSCILLATION
FREQUENCY
ADJUSTMENT
SECTION 5
DIAGRAMS
5-1. IC PIN DESCRIPTIONS
5-1-1. IC201 µPD784216 (PROGRAM, SYSTEM CONTROL)
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
Pin Name
RTP0/P120
RTP1/P121
RTP2/P122
RTP3/P123
RTP4/P124
RTP5/P125
RTP6/P126
RTP7/P127
VDD
X2
X1
VSS
XT2
XT1
RESET
INTP0/P00
INTP1/P01
INTP2/P02
INTP3/P03
INTP4/P04
INTP5/P05
INTP6/P06
AVDD
AVREF0
ANI0/P10
ANI1/P11
ANI2/P12
ANI3/P13
ANI4/P14
ANI5/P15
ANI6/P16
ANI7/P17
AVSS
ANO0/P130
ANO1/P131
AVREF1
SI2
SO2
SCK2
SI1
SO2
SCK1
PCL/P23
BUZ/P24
SI0
SO0
SCK0
A0/P80
A1/P81
A2/P82
A3/P83
I/O
O
O
O
O
O
O
—
—
I
O
I
—
—
—
I
I
—
O
O
O
O
I
I
—
I
—
I
I
I
I
—
I
—
—
—
I
I
O
O
I
O
O
O
—
I
O
O
O
O
O
O
Pin Description
Analog circuit block mute signal output (H: Mute)
D/A mute signal output (H: Mute)
IF circuit block power control signal output (H: ON)
Main circuit block power control signal output (H: ON)
DIR block clock select signal output (H: Digital, L: Analog)
DIR serial select signal output
Not used. (Open)
Not used. (Open)
Power supply pin
Connect to crystal for main system clock oscillator
Connect to crystal for main system clock oscillator
Ground
Not used. (Open)
Not used. (Fix to “L”.)
Reset signal input
DIR audio data detect signal input
Not used. (Open)
Sub DSP serial select signal output
Decoder serial select signal output
Main DSP serial select signal output
SLAVE reset signal output
DIR lock signal input
Power supply pin
Ground
DSP serial BUSY 5 V signal input
Not used. (Open)
Not used. (Open)
Not used. (Open)
Not used. (Open)
Auto mute detect signal (L: OFF, H: ON)
Not used. (Open)
Audio input level signal input
Analog ground
Not used. (Open)
Not used. (Open)
Power supply pin
Main serial data signal input
Main serial data signal output
Main serial clock signal output
Main serial data signal input
Not used. (Open)
Main serial clock signal output
Main DSP reset signal output
Not used.
LED/FLASH serial data signal input
LED/FLASH serial data signal output
LED/FLASH serial clock signal output
Main DSP mute signal output
Not used. (Main DSP ATT setting bit HIGH)
Not used. (Main DSP ATT setting bit LOW)
Main DSP ALC ON signal output
–9–
Pin No.
52
53
54
55
56 – 63
64
65
66
67
68 – 71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95 – 100
Pin Name
A4/P84
A5/P85
A6/P86
A7/P87
AD0 – 7/P40 – 47
A8/P50
A9/P51
A10/P52
A11/P53
A12 – 15/P54 – 57
VSS
A16/P60
A17/P61
A18/P62
A19/P63
RD/P64
WR/P65
WAIT/P66
ASTB/P67
VDD
T05/P100
T06/P101
T07/P102
T08/P103
T00/P30
T01/P31
T02/P32
T03/P33
T04/P34
TI00/P35
TI01/P36
P37
VPP
P90 – 95
I/O
O
O
O
O
—
O
O
O
O
—
—
I
I
I
I
I
I
I
I
I
O
O
O
—
—
—
—
—
—
—
—
—
I
—
Pin Description
Main DSP VR setting bit HIGH signal output
Main DSP VR setting bit LOW signal output
Reserve terminal (Fix to “L”.)
Reserve terminal (Fix to “L”.)
Not used. (Open)
Not used. (Open) (LED 0)
Not used. (Open) (LED 1)
Not used. (Open) (LED 2)
Not used. (Open) (LED 3)
Not used. (Open)
Ground
Power on/off key input
INPUT key input
EFFECT key input
OUTPUT key input
Jump key input
Not used. (Open)
Not used. (Open)
Not used. (Open)
Power supply pin
LEDEN signal output
LEDLAT signal output
LEDRESET signal output
Not used. (Open)
Not used. (Open)
Not used. (Open)
Not used. (Open)
Not used. (Open)
Not used. (Open)
Not used. (Open)
Not used. (Open)
Not used. (Open)
VPP signal input
Not used. (Open)
– 10 –
5-1-2. IC301 CXD9511AQ (DOLBY DIGITAL (AC-3)/PRO LOGIC, DTS DECODER)
Pin No.
1
2
3•4
5
6•7
8
9
10
11
12
13 • 14
15
16
17
18
19
20
21
22
23
24
25 – 29
30
31
32 – 39
40
41
42 – 44
45
46
47
48
49
50
51
52
53
54
55
56
57
58 • 59
60
61
62
63
64
65
66
67
68
69
Pin Name
VDD1
RAMCEN
RAM16 • 15
SDIB0
SDIB1 • 2
XI
XO
VSS
AVDD
SDIB3
TEST
OVFB
DTSDATA
AC3DATA
SPDOB3
CPO
AVSS
ADD2
SDOA2
SDOA1
SDOA0
RAMA14 – 10
VSS
VDD1
OPORT0 – 7
VSS
VDD2
RAMA9 – 7
SDOB2
SDOB1
SDOB0
SDBCK1
SDWCK1
VSS
VDD2
NONPCM
CRC
MUTE
KARAOKE
SCRENC
SDBCK0
RAMA6 • 5
VSS
RAMA4
IC
TEST
RAMA3
CSB
CS
SO
SI
SCK
I/O
I
—
—
I
—
I
—
—
I
—
—
—
—
—
—
O
—
I
O
O
O
—
—
I
—
—
I
—
—
O
O
—
—
—
I
—
—
O
—
—
O
—
—
—
I
—
—
I
I
O
I
I
Pin Description
Power supply pin (+5 V)
Not used. (Open)
Not used. (Open)
PCM signal input
Not used. (Open)
External system clock signal input (12.288 MHz)
Not used. (Open)
Ground
Power supply pin (+3.3 V)
Not used. (Open)
Test pin
Not used. (Open)
Not used. (Open)
Not used. (Open)
Not used. (Open)
PLL signal output
Ground
Power supply pin
PCM signal output (C, LFE output)
PCM signal output (LS, RS output)
PCM signal output (L, R output)
Not used. (Open)
Ground
Power supply pin (+5 V)
Not used. (Open)
Ground
Power supply pin (+3.3 V)
Not used. (Open)
Not used. (Open)
PCM signal output
PCM signal output
Not used. (Open)
Not used. (Open)
Ground
Power supply pin (+3.3 V)
Not used. (Open)
Not used. (Open)
Auto mute detect signal output
Not used. (Open)
Not used. (Open)
SDBCK0 turn over clock signal output
Not used. (Open)
Ground
Not used. (Open)
Initial clear terminal
Test pin
Not used. (Open)
Sub DSP chip select signal input
Interface chip select signal input
Interface data signal output
Interface and sub DSP data signal input
Interface and sub DSP clock signal input
– 11 –
Pin No.
70
71
72 – 79
80
81
82
83
84
85
86 • 87
88
89
90
91
92 • 93
94 – 99
100
Pin Name
RAMA2
VDD1
RAMD0 – 7
VSS
VDD2
SDWCK0
SDBCK0
SDIA0
SDIA1
RAMA1 • 0
RAMWEN
RAMOEN
VSS
VDD2
IPORT7 • 6
IPORT5 – 0
VSS
I/O
—
I
—
—
I
I
I
I
I
—
—
—
—
I
I
—
—
Pin Description
Not used. (Open)
Power supply pin (+5 V)
Not used. (Open)
Ground
Power supply pin (+3.3 V)
SDIA, SDOA, SDIB and SDOB signal word clock signal input
SDIA, SDOA, SDIB and SDOB signal bit clock signal input
AC-3/DTS bitstream (or PCM) data signal input
AC-3/DTS bitstream (or PCM) data signal input
Not used. (Open)
Not used. (Open)
Not used. (Open)
Ground
Power supply pin (+3.3 V)
Input port resister pin
Not used. (Open)
Ground
– 12 –
5-1-3. IC302 XCB56362PV100 (24 BIT AUDIO DIGITAL SIGNAL PROCESSOR)
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50 • 51
52
53
Pin Name
SCK
SS
HREQ
SDO0
SDO1
SDO2
SDO3
VCCS
GNDS
SDO4
SDO5
FST
FSR
SCKT
SCKR
HCKT
HCKR
VCCQL
GNDQ
VCCQL
HDS
HRW
HACK
HOREQ
VCCS
GNDS
ADO
ACI
TIO0
HCS
HA9
HA8
HAS
HAD7
HAD6
HAD5
HAD4
VCCH
GNDH
HAD3
HAD2
HAD1
HAD0
RESET
VCCP
PCAP
GNDP
GNDP1
VCCQH
AA3 • 2
CAS
DE
I/O
I
I
O
O
O
O
O
I
—
O
O
I
I
I
I
—
—
I
—
I
—
—
—
—
I
—
—
—
I
—
—
—
O
—
—
I
I
I
—
I
I
I
I
I
I
I
—
—
I
—
—
—
Pin Description
SPI serial clock signal input
SPI SLAVE select signal input
Host request signal output
Serial data signal output
Serial data signal output
Serial data signal output
Serial data signal output
Power supply pin
Ground
Serial data signal output
Serial data signal output
Transmitter frame sync signal input
Receiver frame sync signal input
Transmitter serial clock signal input
Receiver serial clock signal input
Not used. (Open)
Not used. (Open)
Power supply pin
Ground
Power supply pin
Not used. (Open)
Not used. (Open)
Not used. (Open)
Not used. (Open)
Power supply pin
Not used. (Open)
Not used. (Open)
Not used. (Open)
Timer schmitt trigger signal input
Not used. (Open)
Not used. (Open)
Not used. (Open)
Host address strobe signal output
Not used.
Not used.
Host address signal input
Host address signal input
Power supply pin
Ground
Host address signal input
Host address signal input
Host address signal input
Host address signal input
Reset signal input
Power supply pin
PLL capacitor connecting pin
Ground
Ground
Power supply pin
Not used. (Open)
Not used. (Open)
Not used. (Open)
– 13 –
Pin No.
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69 • 70
71
72 • 73
74
75
76 – 79
80
81
82 – 85
86
87
88 • 89
90
91
92 – 94
95
96
97 – 99
100 – 102
103
104
105 – 110
111
112
113 – 118
119
120
121 – 125
126
127
128
129
130
131 – 133
134
135
136
137
Pin Name
GNDQ
EXTAL
VCCQL
VCCC
GNDC
CLKOUT
NC
PINIT
TA
BR
BB
VCCC
GNDC
WR
RD
AA1 • 0
BG
A0 • 1
VCCA
GNDA
A2 – 5
VCCA
GNDA
A6 – 9
VCCA
GNDA
A10 • 11
GNDQ
VCCQL
A12 – 14
VCCQH
GNDA
A15 – 17
D0 – 2
VCCD
GNDD
D3 – 8
VCCB
GNDD
D9 – 14
VCCD
GNDD
D15 – 19
VCCQL
GNDQ
D20
VCCD
GNDD
D21 – 23
MODD
MODC
MODB
MODA
I/O
—
I
I
I
—
—
—
—
—
—
I
I
—
—
—
—
—
—
I
—
—
I
—
—
I
—
—
—
I
—
I
—
—
—
I
—
—
I
—
—
I
—
—
I
—
—
I
—
—
—
I
I
I
Pin Description
Ground
External clock signal input (12.288 MHz)
Power supply pin
Power supply pin
Ground
Not used. (Open)
Not used. (Open)
Ground
Ground
Not used. (Open)
Bus BUSY signal input
Power supply pin
Ground
Not used. (Open)
Not used. (Open)
Not used. (Open)
Ground
Not used. (Open)
Power supply pin
Ground
Not used. (Open)
Power supply pin
Ground
Not used. (Open)
Power supply pin
Ground
Not used. (Open)
Ground
Power supply pin
Not used. (Open)
Power supply pin
Ground
Not used. (Open)
Not used. (Open)
Power supply pin
Ground
Not used. (Open)
Power supply pin
Ground
Not used. (Open)
Power supply pin
Ground
Not used. (Open)
Power supply pin
Ground
Not used. (Open)
Power supply pin
Ground
Not used. (Open)
Not used. (Fix to “L”.)
Mode select/external discontinue request signal input
Mode select/external discontinue request signal input
Mode select/external discontinue request signal input
– 14 –
Pin No.
138
139
140
141
142
143
144
Pin Name
TRST
TDO
TDI
TCK
TMS
SI
SO
I/O
—
—
—
I
—
I
—
Pin Description
Not used. (Open)
Not used. (Open)
Not used. (Open)
Test clock input
Not used. (Open)
SPI master data signal input
Not used. (Open)
– 15 –
– 16 –
DP-IF5100
5-2. BLOCK DIAGRAMS
5-2-1. BLOCK DIAGRAM — PROCESSOR SECTION —
DELTA
SIGMA
MODULATOR
B+
(SW+9V)
6
R CH
-8dB
DIGITAL
AUDIO D OUT
19
INTERFACE
(1/2)
DECIMATION/
FILTER
85 SDIA1
ANALOG
FRONT END
V IN R
DOLBY DIGITAL(AC-3)
/PRO LOGIC,DTS
DECODER
IC301
ATT SW
Q101
0dB
DIGITAL AUDIO,INTERFACE RECEIVER
IC304
OPTICAL
RECEIVER
MODULE
IC305
OUT 1
DIGITAL IN
VCC 3
37
DDIN
B+
(+5V)
EIAJ(AES/EBU)
DIGITAL AUDIO
INTERFACE
DECODER
ASYNCHRONOUS
BUFFER
S/P
P/S
DOUT
MCC
B+
(SW+5V)
39 VDD
24 VDDA
SYSTEM CLOCK
TIMING OCCURENCE
µ-CON
INTERFACE
WC
RSTN
12
13
B+
(+3.3V)
11
•
41
•
51 VDD2
•
81
•
91
DIRSG
3
/BCK
7
LRCK
8
23
B+
(SW+5V)
1
•
31 VDD1
•
71
84 SDIA0
IC307(2/2)
HREQ 3
B+
(+5V)
NOSG3V
BUSY 3V
LOGIC LEVEL
CONVERTER
IC303
1
2
3
5
4
6
LR DATA
SDO1 5
BCK
SDBCK0 57
F1DA
SDOB1 46
SRESET
IC 62
83 SDBCK0
82 SDWCK0
SRESET
8 X1
SO2
SI 68
SCK2
SCK 69
CSB
CS
SO
MUTE
38
39
42
18
19
37
30
BCK
F1DA
SRESET
LRCK
MCK
2
CSSD
65
CSYM
66
SI2
67
YMMUTE
54
A16/P60
A17/P61
A18/P62
A19/P63
BUSY 5V
25
NOSG 5V
32
1
2
POWER
73
SELECT
74
EFFECT
75
OUTPUT
76
SO0
SCK0
TO5/P100
TO6/P101
46
47
82
83
TO7/P102 84
SO0
SCK0
LEDEN
LEDLAT
LEDRES
AMUTE
DAMUTE
SW
BLOCK
SW1-5
DISPLAY
LED DRIVE
IC205
13
14
2
3
15
4
IC306
SIN
SCK
EN
LAT
RES
SO
01 12
I I
08 5
DISPLAY
LED
D201-208
DISPLAY
LED DRIVE
IC206
12M/3V
6 RTP5/P125
13
14
2
3
15
40 SI1
B+
(UN+5.7V)
• Signal Path
9
81
23
36
VDD
VDD
AVDD
AVREF1
PROGRAM,
SYSTEM
CONTROL
IC201
SI0 45
: ANALOG
TRANSMITTER
SECTION
(Page 19)
3
POWER
4 RTP3/P123
LEDPOWER
3 RTP2/P122
15 RESET
RESET
TRANSMITTER
SECTION
(Page 19)
22 INTP6/P06
5 RTP4/P124
VPP 94
04
– 17 –
TRANSMITTER
SECTION
(Page 19)
ANI0/P10
ANI7/P13
RTP0/P120
RTP1/P121
SO2
SCK2
SCK1
INTP2/P02
INTP3/P03
SI2
ANI5/P15
16 INTP0/P00
21 INTP5/P05
: DIGITAL
1
2 34 35 36 37 40 43 44
IC307(1/2)
MCK
LOCKN
CLKSEL
HAS 33
B+
(+3.3V)
20 55 54 53 52 51 48 43
12.288M
X301
12.288MHz
VCCD 103
55 EXTAL
143 SI
22 15 10
CSDIR
SI1
DIRSCK
42 43 44
CLFSG
CLRSG
LRSG
8
18
20
38
45
57
74
DSPMUTE
DSPRESET
R CH
IF5000SG
VCCS
VCCQL
VCCQH
VCCH
VCCP
VCCC
VCCA
HAD4
HAD3
HAD0
RESET
ANALOG
FRONT END
V IN L
24BIT AUDIO
DIGITAL
SIGNAL
PROCESSOR
IC302
SDO0
SDO2
SDO3
SDO4
SDO5
SCKT
SCKR
FST
FSR
SCK
37/P83
A0/P90
PCL/P23
1
4
6
7
10
11
14
15
12
13
1
SS
HAD7
HAD6
HAD5
1
VPOUT
CSDSP
TMP3
TMP2
VRSBL
VRSBH
ALCON
SW101
ATT
2
3
SDIB0 5
SDOB0 47
SDOA2 22
SDOA1 23
SDOA0 24
A7/P87
A6/P86
A5/P85
A4/P84
-1
J101
L
LINE INPUT
R
-2
A/D CONVERTER
IC102(1/2)
INTP4/PO4
LINE AMP
IC101
– 18 –
SIN
SCK
EN
LAT
RES
01 12
I I
08 5
DISPLAY
LED
D209-216
DP-IF5100
5-2-2. BLOCK DIAGRAM — TRANSMITTER SECTION —
MUTE SWITCH
IC104
1
LR DATA
18
LR CK
BCK
16
17
(Page 18)
MCK
22
DIN
DIGITAL
AUDIO
INTERFACE
(2/2)
INTERPOLATION
FILTER
LPF
&
BUFFER
DELTA SIGMA
MODULATION
BIAS
V OUT L
15
V COM
BINAURAL L
5
11
4
CLK/OSC
MANAGER
V OUT R
12
14
9
10
8
BINAURAL L
OSC
Q51
14
L51
FREQUENCY
(L-CH)
6
2.3MHz OSC
COIL
4
1
5
6
7
BINAURAL R
PROCESSOR
SECTION
B+
(+9V)
RV1
RF LEVEL
(R-CH)
OSC
Q1
LED
DRIVE
Q302,352
BUFFER
Q2
13
28
SRESET
RESET
2
(Page 18)
6
L1
FREQUENCY
(R-CH)
LOGIC
LEVEL
CONVERTER
2
4
2.8MHz OSC
COIL
B+
(SW+5V)
9
A MUTE
F1DA
10
DAMUTE
11
B+
(UN+5.7V)
MUTE 15
16 VCC
B+
(UN+5V)
LPF
IC106
SDATA
27
BCK
26
LRCK
25
SERIAL
DATA
INTERFACE
ATTEN/
MUTE
8x
INTERPOLATOR
MULTIBIT
SIGMA-DELTA
MODULATOR
R CH
2
MCLK
DAC
OUTPUT
BUFFER
2
3
17
MUTE
Q901
RV901
PHONES LEVEL
6
5
-1
L
R CH
5
6
12
7
MUTE
Q902
CLOCK
CIRCUIT
24
PD/RST
23
MUTE
B+
(SW+5V) 28
DVDD
-2
R
STEREO AUDIO DAC SYSTEM
IC105
8
8
1
6
5
7
HEADPHONES
AMP
IC901
3
2
J901
PHONES
7
HEADPHONES
AMP
IC902
3
2
1
1
LED POWER
B+
(+9V)
+9V
REG
IC805
LF801
PROCESSOR
SECTION
B+
(+3.3V)
3
+3.3V
REG
IC803
+9V
REG
IC804
(Page 18)
: DIGITAL
B+
(SW+9V)
B+
(SW+5V)
: ANALOG
04
: RF
RESET
IC204
RESET
B+
(UN+5V)
+5V
REG
IC802
UN5.7V
REG
IC801
UN+5V
REG
Q903
B+
(UN+5.7V)
– 19 –
J801
DC IN 9V
!
POWER
• Signal Path
INFRARED
EMITTER
D301-304
2
D1
3
2
BINAURAL R
LED
DRIVE
Q301,351
BUFFER
Q52
3
12
LPF
&
BUFFER
13
12
B+
(+9V)
RV51
RF LEVEL
(L-CH)
D51
D/A CONVERTER
IC102(2/2)
PROCESSOR
SECTION
EMPHASIS & LPF
IC103
– 20 –
INFRARED
EMITTER
D305-308
DP-IF5100
5-3. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
5-3-1. PRINTED WIRING BOARD — TX BOARD —
1
• Semiconductor
Location
2
3
4
5
6
7
8
A
Ref. No.
D1
D51
D101
D102
D103
D104
D201
D202
Location
G-4
F-4
H-10
H-10
G-5
I-10
E-5
B-3
IC101
IC102
IC103
IC104
IC105
IC106
IC201
IC204
IC301
IC302
IC303
IC304
IC306
IC307
G-10
E-6
F-4
G-5
E-7
G-8
C-3
E-3
D-8
C-6
D-4
E-9
E-8
C-4
Q1
Q2
Q51
Q52
Q101
Q102
G-3
H-3
F-3
F-2
G-9
G-10
B
C
D
E
F
TP
(A MUTE)
G
H
Note:
• X : parts extracted from the component side.
a
•
: Through hole.
• b : Pattern from the side which enables seeing.
(The other layer’s patterns are not indicated.)
Caution:
Pattern face side:
(Side B)
Parts face side:
(Side A)
Parts on the pattern face side seen from the
pattern face are indicated.
Parts on the parts face side seen from the
parts face are indicated.
I
J
– 21 –
– 22 –
9
10
11
DP-IF5100
11
10
9
8
7
6
5
4
3
2
1
A
B
(Page 30)
C
• Semiconductor
Location
Ref. No.
IC305
IC801
IC802
IC803
IC804
IC805
Location
E-11
H-8
I-9
H-6
H-9
I-5
• Waveforms
1
5Vp-p
D
21µsec
IC102 qh (LRCK)
2
4.8Vp-p
E
0.3µsec
IC102 qj (BCKIN)
3
3.2Vp-p
F
8MHz
IC201 qa (X1)
4
5Vp-p
G
(Page 29)
0.3µsec
IC301 tj (SDBCK0)
5
5Vp-p
H
22µsec
IC302 qs (FST) qd (FSR)
6
5Vp-p
(Page 33)
I
0.3µsec
IC304 7 (MCC)
7
3.3Vp-p
J
– 23 –
– 24 –
12.288MHz
IC304 qs (XI)
DP-IF5100
5-3-2. SCHEMATIC DIAGRAM — TX BOARD (1/2) — • Refer to page 35 for IC Block Diagrams. • Refer to page 24 for Waveforms.
(Page
31)
(Page
34)
(Page
31)
(Page 27, 28)
Note:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/ 4 W or less unless otherwise
specified.
f
•
: internal component.
• C : panel designation.
• U : B+ Line.
• H : adjustment for repair.
– 25 –
• Power voltage is dc 9 V and fed with regulated dc power
supply from external power voltage jack.
• Voltage and waveforms are dc with respect to ground
under no-signal conditions.
no mark : DIGITAL mode
(
) : ANALOG mode
: Impossible to measure
∗
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production tolerances.
• Circled numbers refer to waveforms.
• Signal path.
F : ANALOG
J : RF
c : DIGITAL
– 26 –
DP-IF5100
5-3-3. SCHEMATIC DIAGRAM — TX BOARD (2/2) — • Refer to page 36 for IC Block Diagrams. • Refer to page 24 for Waveforms.
Note:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/ 4 W or less unless otherwise
specified.
• U : B+ Line.
• Power voltage is dc 9 V and fed with regulated dc power
supply from external power voltage jack.
• Voltage and waveforms are dc with respect to ground
under no-signal conditions.
no mark : DIGITAL mode
(
) : ANALOG mode
: Impossible to measure
∗
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production tolerances.
• Circled numbers refer to waveforms.
• Signal path.
F : ANALOG
J : RF
c : DIGITAL
(Page 26)
LOGIC LEVEL
CONVERTER
LOGIC LEVEL
CONVERTER
(Page 26)
– 27 –
– 28 –
DP-IF5100
5-3-4. PRINTED WIRING BOARD — LED BOARD —
1
2
3
4
5
6
7
8
9
10
11
12
13
A
(Page 24)
(Page 24)
B
C
D
E
F
G
Note:
• X : parts extracted from the component side.
• b : Pattern from the side which enables seeing.
– 29 –
– 30 –
14
DP-IF5100
5-3-5. SCHEMATIC DIAGRAM — LED BOARD — • Refer to page 36 for IC Block Diagrams.
• Semiconductor
Location
Ref. No.
D201
D202
D203
D204
D205
D206
D207
D208
D209
D210
D211
D212
D213
D214
D215
D216
D301
D302
D303
D304
D305
D306
D307
D308
Location
E-13
F-11
F-10
F-3
F-6
E-7
F-5
D-5
C-5
E-4
D-4
F-4
C-4
F-9
F-6
F-9
G-13
G-10
G-7
G-4
B-13
B-10
B-7
B-4
IC205
IC206
C-12
D-7
Q301
Q302
Q351
Q352
G-4
B-3
G-3
B-3
(Page 26)
(Page 26)
– 31 –
Note:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.
• C : panel designation.
• U : B+ Line.
• Power voltage is dc 9 V and fed with regulated dc power
supply from external power voltage jack.
• Voltage is dc with respect to ground under no-signal
condition.
no mark : DIGITAL mode
(
) : ANALOG mode
: Impossible to measure
∗
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production tolerances.
• Signal path.
J
: RF
– 32 –
DP-IF5100
5-3-6. PRINTED WIRING BOARD — AMP BOARD —
2
1
3
5-3-7. SCHEMATIC DIAGRAM — AMP BOARD —
4
5
6
7
(Page 24)
A
B
C
(Page 25)
D
E
F
• Semiconductor
Location
Ref. No.
IC901
IC902
Location
D-5
D-4
Q901
Q902
Q903
C-2
B-2
C-6
Note:
• X : parts extracted from the component side.
• b : Pattern from the side which enables seeing.
– 33 –
Note:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/ 4 W or less unless otherwise
specified.
• C : panel designation.
• U : B+ Line.
• Power voltage is dc 9 V and fed with regulated dc power
supply from external power voltage jack.
• Voltage is dc with respect to ground under no-signal
condition.
no mark : DIGITAL/ANALOG mode
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production tolerances.
• Signal path.
F : ANALOG
– 34 –
5-4. IC BLOCK DIAGRAMS
X-COM
IX
OX
A
B
C
13
12
11
10
9
IN
OUT
C
27 FMT0
26 FMT1
IN
OUT
C
25 FMT2
24 DGND
–
23 VDD
+
CLK/OSC
MANAGER
22 CLKIO
21 XTO
20 XTI
C
OUT
IN
C
OUT
IN
IN
1
2
3
4
5
6
7
8
GND
C
OUT
IN
DELTA SIGMA MODULATOR
VCOM
VOUTR
AGND2
VCC2
OUT
C
VEE
INTERPOLATION
FILTER
DOUT
DIN
BCKIN
LRCIN
Z-COM
19
18
17
16
DIGITAL
AUDIO
INTERFACE
IZ
DECIMATION
FILTER
OY
–
IY
+
DELTA SIGMA MODULATOR
INH
7
8
9
10
ANALOG
FRONT-END
15 14
OZ
ANALOG
FRONT-END
16
LOGIC LEVEL CONVERTOR
REFERENCE
VINR 6
CINPR
CINNR
CINNL
CINPL
28 RSTB
RESET
Y-COM
1
2
3
4
5
FORMAT CONTROL
INTERFACE
VINL
VCC1
AGND1
VREFL
VREFR
VCC
IC104 TC74HC4053AFT
IC102 PCM3001E-T2
BIAS
11
12
13
14
LPF &
BUFFER
LPF &
BUFFER
15 VOUTL
IC204 RN5VL42AA-TL
IC105 AD1855JRSRL
DIGITAL
SUPPLY
DGND 1 DGND
28 DVDD
VSS
3
VDD
2
OUT
1
MCLK 2
CS 3
SCK 4
SI 5
27 SDATA
26 BCK
25 LRCK
SERIAL
DATA
INTERFACE
SERIAL
CONTROL
INTERFACE
PD/RST
384/256 6
X2CLK 7
CLOCK
CIRCUIT
ZEROR 8
FLAG
DEEMP 9
DE-EMPHASIS
ATTEN/
MUTE
96/48 10
AGND 11 AGND
OUTR+ 12
OUTR– 13
FILTR 14
OUTPUT
BUFFER
ATTEN/
MUTE
MUTE
8X
INTERPOLATOR
8X
INTERPOLATOR
MULTIBIT
SIGMA-DELTA
MODULATOR
MULTIBIT
SIGMA-DELTA
MODULATOR
DAC
DAC
VOLTAGE
REFERENCE
24 PD/RST
–
+
VREF
23 MUTE
22 ZEROL
21 IDPM0
20 IDPM1
19 FILTB
ANALOG
SUPPLY
18 A VDD
OUTPUT
BUFFER
17 OUTL+
16 OUTL–
AGND 15 AGND
– 35 –
4
NC
5
NC
IC205, 206 µPD6345GS
16 VDD
Vss 1
15 RES
EN 2
100k
100k
100k
100k
14 SCK
LAT 3
SO 4
S8
S7
S6
S5
S4
S3
S2
13 SIN
S1
100k
P8
P7
P6
P5
P4
P3
P2
P1
O8 5
12 O1
O7 6
11 O2
O6 7
10 O3
O5 8
9 O4
KM0
KM2
TSTN
VSSA
CTPL
(NC)
PCD
CLTN
VDDA
RSTN
31
32
31
30 29
28 27 26 25
24 23
FSO 34
CSM 35
EXTW 36
DDIN
LR
VDD
ERR
EMP
IC303 TC74VHCT08AFT (EL)
FS1
IC304 YM3436D
21
20
19
18
17
16
15
14
CDO 42
DATA CLOCK
CONTROL
SYSTEM CLOCK
TIMING OCCURENCE
1
2
3 4
5 6 7 8 9 10 11
OPT
SYNC
MCC
WC
MCB
MCA
SKSY
P/S
DOUT
VFL
ASYNCHRONOUS
BUFFER
(L, R ONE WORD)
HDLT
S/P
DAUX
CCK 43
CLD 44
1B 2
13 4B
1Y 3
12 4A
2A 4
11 4Y
2B 5
10 3B
2Y 6
9 3A
GND 7
8 3Y
22 KM1
EIAJ (AES/EBU)
DIGITAL AUDIO
INTERFACE
DECODER
u-CON
INTERFACE
14 VCC
PLL
SEL
37
38
39
40
41
1A 1
DOM0
DOM1
DIM0
DIM1
TST2
VSS
LOCKN
P256
13 XO
12 XI
IC305 TORX178A
AMP
CIRCUIT
CONVERTER
1 OUT
2 GND
3 VCC
– 36 –
GND
IN A
IN B
IC306 TC7SH08FU
3
2
1
5
OUT Y
VCC
1
IN
4
2
GND
3
OUT
EXCLUSIVE
IC
1
2
VIN VOUT
IC803 BA033T
REFERENCE
VOLTAGE
1
VCC
IC802 PQ05RD11
IC804, 805 PQ09RD11
IC801 TA78057S
IC307 TC7W04FU
–
IN1
1
8
VDD
OUT2
2
7
OUT1
IN3
3
6
IN2
VSS
4
5
OUT3
+
2
GND
3
OUT
– 37 –
3
GND
4
VC
SECTION 6
EXPLODED VIEW
NOTE:
• The mechanical parts with no reference
number in the exploded views are not supplied.
• Items marked “*” are not stocked since
they are seldom required for routine service.
Some delay should be anticipated
when ordering these items.
• -XX and -X mean standardized parts, so
they may have some difference from the
original one.
• Color Indication of Appearance Parts
Example :
KNOB, BALANCE (WHITE) ... (RED)
R
R
Parts Color Cabinet’s Color
15
8
9
6
17
15
3
1
17
10
2
7
17
5
11
not
supplied
supplied with RV
16
17
4
17
18
14
13
supplied with JACK
12
18
16
18
not
supplied
13
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
1
* 2
* 3
4
* 5
X-4952-190-1
4-223-990-01
4-223-989-01
4-213-828-01
4-223-991-01
PANEL ASSY, FRONT
PLATE (B), LIGHT GUIDE
PLATE (A), LIGHT GUIDE
KNOB (VOL)
PLATE (C), LIGHT GUIDE
Remark
10
11
* 12
13
14
1-790-199-11
X-4952-191-1
A-4542-613-A
3-922-535-11
4-224-922-01
WIRE, PARALLEL 6P
COVER ASSY
TX BOARD, COMPLETE
SCREW (+BTT)
SCREW (2.6X6) (S TITE)
6
* 7
* 8
9
4-223-999-01
A-4542-611-A
A-4542-612-A
1-790-200-11
PANEL, SUB
AMP BOARD, COMPLETE
LED BOARD, COMPLETE
WIRE, PARALLEL 12P
15
16
17
18
7-685-105-19
7-685-645-79
7-685-791-04
7-685-647-79
SCREW +P 2X8 TYPE2 NON-SLIT
SCREW +P 3X6 TYPE2 NON-SLIT
SCREW +PTT 2.6X5 (S)
SCREW +BVTP 3X8 TYPE2 IT-3
– 38 –
Remark
SECTION 7
ELECTRICAL PARTS LIST
NOTE:
• Due to standardization, replacements in
the parts list may be different from the
parts specified in the diagrams or the
components used on the set.
• -XX and -X mean standardized parts, so
they may have some difference from the
original one.
• RESISTORS
All resistors are in ohms.
METAL:Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F:nonflammable
• Items marked “*” are not stocked since
they are seldom required for routine service.
Some delay should be anticipated
when ordering these items.
• SEMICONDUCTORS
In each case, u : µ, for example:
uA.. : µA.. uPA.. : µPA..
uPB.. : µPB.. uPC.. : µPC.. uPD.. : µPD..
• CAPACITORS
uF : µF
• COILS
uH : µH
Ref. No.
Part No.
Description
Remark
*
A-4542-611-A AMP BOARD, COMPLETE
*********************
Ref. No.
C901
C902
C903
C904
C905
1-115-197-11
1-115-197-11
1-104-545-11
1-104-545-11
1-124-584-00
ELECT
ELECT
FILM CHIP
FILM CHIP
ELECT
100uF
100uF
0.0033uF
0.0033uF
100uF
20%
20%
5%
5%
20%
25V
25V
16V
16V
10V
C906
C907
C908
C909
C910
1-124-584-00
1-127-694-11
1-127-694-11
1-115-198-11
1-115-198-11
ELECT
ELECT
ELECT
ELECT
ELECT
100uF
47uF
47uF
470uF
470uF
20%
20%
20%
20%
20%
10V
25V
25V
25V
25V
C911
C912
C913
C914
1-127-693-51
1-115-339-11
1-115-339-11
1-124-233-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
1000uF
0.1uF
0.1uF
10uF
20%
10%
10%
20%
16V
50V
50V
16V
< IC >
8-759-358-47 IC NJM2115V(TE2)
8-759-648-12 IC AD8532ARU-REEL
< JACK >
J901
1-216-296-91 SHORT
Description
Remark
1-216-049-11
1-216-049-11
1-216-075-00
1-216-075-00
1-216-081-00
RES,CHIP
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
12K
12K
22K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R906
R907
R908
R909
R910
1-216-081-00
1-216-049-11
1-216-049-11
1-216-083-00
1-216-083-00
METAL CHIP
RES,CHIP
RES,CHIP
METAL CHIP
METAL CHIP
22K
1K
1K
27K
27K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R911
R912
R913
R914
R915
1-216-005-00
1-216-005-00
1-216-073-00
1-216-073-00
1-216-025-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
RES,CHIP
15
15
10K
10K
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R916
R917
R918
R919
R920
1-216-025-11
1-216-049-11
1-216-065-11
1-216-073-00
1-216-073-00
RES,CHIP
RES,CHIP
RES,CHIP
METAL CHIP
METAL CHIP
100
1K
4.7K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R921
R922
1-216-057-00 METAL CHIP
1-216-057-00 METAL CHIP
2.2K
2.2K
5%
5%
1/10W
1/10W
< VARIABLE RESISTOR >
RV901 1-237-671-11 RES, VAR, CARBON 10K/10K (PHONES LEVEL)
*************************************************************
0
A-4542-612-A LED BOARD, COMPLETE
********************
*
< FERRITE BEAD >
L902
L903
L904
L905
L906
1-414-235-22
1-414-235-22
1-414-235-22
1-414-235-22
1-414-235-22
L907
L908
L910
1-414-235-22 FERRITE BEAD INDUCTOR
1-414-235-22 FERRITE BEAD INDUCTOR
1-414-235-22 FERRITE BEAD INDUCTOR
FERRITE BEAD INDUCTOR
FERRITE BEAD INDUCTOR
FERRITE BEAD INDUCTOR
FERRITE BEAD INDUCTOR
FERRITE BEAD INDUCTOR
< TRANSISTOR >
Q901
Q902
Q903
When indicating parts by reference
number, please include the board.
R901
R902
R903
R904
R905
1-766-850-11 JACK (LARGE TYPE) (PHONES)
< JUMPER RESISTOR>
JC901
LED
< RESISTOR >
< CAPACITOR >
IC901
IC902
Part No.
AMP
8-729-043-69 TRANSISTOR UN2225-(TX).SO
8-729-043-69 TRANSISTOR UN2225-(TX).SO
8-729-230-49 TRANSISTOR 2SC2712-YG
< CAPACITOR >
C201
C202
C203
C204
C205
1-163-038-00
1-163-038-00
1-124-589-11
1-163-038-00
1-163-038-00
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
47uF
0.1uF
0.1uF
C206
C207
C209
C210
C211
1-163-038-00
1-163-038-00
1-163-031-11
1-163-031-11
1-163-031-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.01uF
0.01uF
0.01uF
25V
25V
50V
50V
50V
C212
1-163-031-11 CERAMIC CHIP
0.01uF
50V
– 39 –
20%
25V
25V
16V
25V
25V
LED
Ref. No.
C213
C290
C301
C351
TX
Part No.
Description
1-163-031-11
1-163-009-11
1-163-038-00
1-126-382-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
Remark
Part No.
Description
R202
R203
R204
R205
R206
1-216-057-00
1-216-057-00
1-216-057-00
1-216-057-00
1-216-057-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.2K
2.2K
2.2K
2.2K
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
< DIODE >
R207
R208
R209
R210
R211
1-216-061-00
1-216-061-00
1-216-061-00
1-216-061-00
1-216-061-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
3.3K
3.3K
3.3K
3.3K
3.3K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
LED
LED
LED
LED
LED
R212
R213
R214
R215
R216
1-216-061-00
1-216-061-00
1-216-057-00
1-216-057-00
1-216-057-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
3.3K
3.3K
2.2K
2.2K
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R301
R302
R351
R352
1-216-003-11
1-216-003-11
1-216-003-11
1-216-003-11
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
12
12
12
12
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
0.01uF
0.001uF
0.1uF
100uF
10%
20%
Ref. No.
50V
50V
25V
16V
Remark
< CONNECTOR >
CN902
CN903
1-691-071-31 HOUSING, CONNECTOR 12P
1-691-065-31 HOUSING, CONNECTOR 6P
D201
D202
D203
D204
D205
8-719-072-97
8-719-077-16
8-719-077-16
8-719-077-16
8-719-077-16
TLG124A(TPJ52) (POWER)
TLSU124(TPJ52) (DIGITAL)
TLSU124(TPJ52) (ANALOG)
TLSU124(TPJ52) (VIRTUAL)
TLSU124(TPJ52) (DOLBY SURROUND
(DECODE MODE))
D206
D207
D208
D209
D210
8-719-077-16 LED TLSU124(TPJ52) (DOLBY DIGITAL
(DECODE MODE))
8-719-077-15 LED TLOU124(TPJ52-SONY) (L)
8-719-077-15 LED TLOU124(TPJ52-SONY) (C)
8-719-077-15 LED TLOU124(TPJ52-SONY) (R)
8-719-077-15 LED TLOU124(TPJ52-SONY) (HL)
D211
D212
D213
D214
D215
8-719-077-15
8-719-077-15
8-719-077-15
8-719-077-16
8-719-077-16
LED
LED
LED
LED
LED
TLOU124(TPJ52-SONY) (HR)
TLOU124(TPJ52-SONY) (LS)
TLOU124(TPJ52-SONY) (RS)
TLSU124(TPJ52) (CINEMA)
TLSU124(TPJ52) (DTS (DECODE MODE))
D216
D301
D302
D303
D304
8-719-077-16
8-719-052-34
8-719-052-34
8-719-052-34
8-719-052-34
LED
LED
LED
LED
LED
TLSU124(TPJ52) (MUSIC)
DAL5821(INFRARED EMITTER)
DAL5821(INFRARED EMITTER)
DAL5821(INFRARED EMITTER)
DAL5821(INFRARED EMITTER)
D305
D306
D307
D308
8-719-052-34
8-719-052-34
8-719-052-34
8-719-052-34
LED
LED
LED
LED
DAL5821(INFRARED EMITTER)
DAL5821(INFRARED EMITTER)
DAL5821(INFRARED EMITTER)
DAL5821(INFRARED EMITTER)
< SWITCH >
SW1
1-571-760-11 SWITCH, KEY BOARD (POWER)
SW2
1-571-760-11 SWITCH, KEY BOARD (INPUT)
SW3
1-571-760-11 SWITCH, KEY BOARD (OUTPUT)
SW4
1-571-760-11 SWITCH, KEY BOARD (EFFECT)
*************************************************************
A-4542-613-A TX BOARD, COMPLETE
*******************
*
7-685-647-79 SCREW +BVTP 3X8 TYPE2 IT-3
< CAPACITOR >
C5
C6
C7
C8
C9
1-124-234-00
1-124-589-11
1-164-182-11
1-163-227-11
1-164-161-11
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
22uF
47uF
0.0033uF
10PF
0.0022uF
20%
20%
10%
0.5PF
10%
16V
16V
50V
50V
100V
C10
C11
C12
C13
C34
1-163-107-00
1-163-227-11
1-163-109-00
1-164-161-11
1-124-589-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
39PF
10PF
47PF
0.0022uF
47uF
5%
0.5PF
5%
10%
20%
50V
50V
50V
100V
16V
C36
C37
C38
C39
C40
1-163-038-00
1-124-589-11
1-163-038-00
1-124-589-11
1-163-038-00
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
0.1uF
47uF
0.1uF
47uF
0.1uF
C55
C56
C57
C58
C59
1-124-234-00
1-124-589-11
1-164-182-11
1-163-229-11
1-164-161-11
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
22uF
47uF
0.0033uF
12PF
0.0022uF
20%
20%
10%
5%
10%
16V
16V
50V
50V
100V
C60
1-163-109-00 CERAMIC CHIP
47PF
5%
50V
< IC >
IC205
IC206
8-759-560-82 IC uPD6345GS-T1
8-759-560-82 IC uPD6345GS-T1
< JUMPER RESISTOR>
JC202
JC204
1-216-296-91 SHORT
1-216-296-91 SHORT
0
0
< TRANSISTOR >
Q301
Q302
Q351
Q352
8-729-106-68
8-729-106-68
8-729-106-68
8-729-106-68
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SD1615A-GP
2SD1615A-GP
2SD1615A-GP
2SD1615A-GP
< RESISTOR >
R201
1-216-033-00 METAL CHIP
220
5%
1/10W
– 40 –
20%
20%
25V
16V
25V
16V
25V
TX
Ref. No.
Part No.
Description
Part No.
Description
C61
C62
C63
C101
C102
1-163-229-11
1-163-111-00
1-164-161-11
1-163-117-00
1-163-117-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
12PF
56PF
0.0022uF
100PF
100PF
5%
5%
10%
5%
5%
50V
50V
100V
50V
50V
Remark
Ref. No.
C161
C162
C163
C164
C165
1-115-339-11
1-136-478-11
1-136-478-11
1-136-437-11
1-136-437-11
CERAMIC CHIP
FILM
FILM
FILM
FILM
0.1uF
470PF
470PF
220PF
220PF
10%
5%
5%
5%
5%
50V
630V
630V
630V
630V
C103
C104
C107
C108
C109
1-124-233-11
1-124-233-11
1-124-233-11
1-124-233-11
1-163-117-00
ELECT
ELECT
ELECT
ELECT
CERAMIC CHIP
10uF
10uF
10uF
10uF
100PF
20%
20%
20%
20%
5%
16V
16V
16V
16V
50V
C166
C167
C168
C169
C201
1-136-270-11
1-136-270-11
1-115-197-11
1-115-197-11
1-126-916-11
FILM
FILM
ELECT
ELECT
ELECT
47PF
47PF
100uF
100uF
1000uF
5%
5%
20%
20%
20%
630V
630V
25V
25V
6.3V
C110
C111
C112
C113
C114
1-163-117-00
1-163-021-11
1-126-382-11
1-115-339-11
1-124-584-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
100PF
0.01uF
100uF
0.1uF
100uF
5%
10%
20%
10%
20%
50V
50V
16V
50V
6.3V
C202
C203
C204
C205
C206
1-115-339-11
1-126-968-11
1-115-339-11
1-115-339-11
1-126-968-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.1uF
100uF
0.1uF
0.1uF
100uF
10%
20%
10%
10%
20%
50V
6.3V
50V
50V
6.3V
C115
C116
C117
C118
C119
1-124-584-11
1-124-233-11
1-115-339-11
1-124-233-11
1-124-233-11
ELECT
ELECT
CERAMIC CHIP
ELECT
ELECT
100uF
10uF
0.1uF
10uF
10uF
20%
20%
10%
20%
20%
6.3V
16V
50V
16V
16V
C207
C208
C209
C210
C301
1-115-339-11
1-115-339-11
1-115-339-11
1-115-339-11
1-115-339-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
10%
10%
10%
10%
10%
50V
50V
50V
50V
50V
C120
C121
C122
C123
C124
1-163-005-11
1-163-005-11
1-124-233-11
1-124-233-11
1-115-339-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
470PF
470PF
10uF
10uF
0.1uF
10%
10%
20%
20%
10%
50V
50V
16V
16V
50V
C302
C303
C304
C305
C306
1-115-339-11
1-124-584-11
1-115-339-11
1-115-339-11
1-124-584-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.1uF
100uF
0.1uF
0.1uF
100uF
10%
20%
10%
10%
20%
50V
6.3V
50V
50V
6.3V
C125
C126
C127
C128
C129
1-115-339-11
1-163-009-11
1-115-339-11
1-124-234-00
1-124-234-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
0.1uF
0.001uF
0.1uF
22uF
22uF
10%
10%
10%
20%
20%
50V
50V
50V
16V
16V
C307
C308
C309
C310
C311
1-115-339-11
1-115-339-11
1-115-339-11
1-115-339-11
1-115-339-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
10%
10%
10%
10%
10%
50V
50V
50V
50V
50V
C130
C131
C132
C133
C136
1-163-117-00
1-163-117-00
1-163-019-00
1-163-019-00
1-104-542-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
FILM CHIP
100PF
100PF
0.0068uF
0.0068uF
0.0018uF
5%
5%
10%
10%
5%
50V
50V
50V
50V
50V
C312
C313
C314
C315
C316
1-115-339-11
1-115-339-11
1-115-339-11
1-115-339-11
1-115-339-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
10%
10%
10%
10%
10%
50V
50V
50V
50V
50V
C137
C138
C139
C140
C141
1-104-542-11
1-104-538-11
1-104-538-11
1-104-532-11
1-104-532-11
FILM CHIP
FILM CHIP
FILM CHIP
FILM CHIP
FILM CHIP
0.0018uF
820PF
820PF
270PF
270PF
5%
5%
5%
5%
5%
50V
50V
50V
50V
50V
C317
C318
C330
C331
C332
1-130-467-00
1-107-823-11
1-115-339-11
1-115-339-11
1-124-584-11
MYLAR
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
470PF
0.47uF
0.1uF
0.1uF
100uF
5%
10%
10%
10%
20%
50V
16V
50V
50V
6.3V
C142
C143
C144
C145
C146
1-126-382-11
1-115-339-11
1-126-382-11
1-124-584-11
1-115-339-11
ELECT
CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
100uF
0.1uF
100uF
100uF
0.1uF
20%
10%
20%
20%
10%
16V
50V
16V
6.3V
50V
C333
C334
C335
C336
C337
1-115-339-11
1-115-339-11
1-115-339-11
1-115-339-11
1-115-339-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
10%
10%
10%
10%
10%
50V
50V
50V
50V
50V
C150
C151
C152
C153
C154
1-124-233-11
1-115-197-11
1-115-339-11
1-128-197-11
1-115-339-11
ELECT
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
10uF
100uF
0.1uF
10uF
0.1uF
20%
20%
10%
20%
10%
16V
25V
50V
50V
50V
C338
C339
C340
C341
C342
1-107-823-11
1-115-339-11
1-115-339-11
1-115-339-11
1-115-339-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.47uF
0.1uF
0.1uF
0.1uF
0.1uF
10%
10%
10%
10%
10%
16V
50V
50V
50V
50V
C155
C156
C160
1-128-197-11 ELECT
1-115-339-11 CERAMIC CHIP
1-115-197-11 ELECT
10uF
0.1uF
100uF
20%
10%
20%
50V
50V
25V
C343
C344
C345
1-115-339-11 CERAMIC CHIP
1-115-339-11 CERAMIC CHIP
1-115-339-11 CERAMIC CHIP
0.1uF
0.1uF
0.1uF
10%
10%
10%
50V
50V
50V
– 41 –
Remark
TX
Ref. No.
Part No.
Description
Part No.
Description
C346
C347
C348
C349
C350
1-115-339-11
1-115-339-11
1-115-339-11
1-115-339-11
1-115-339-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
10%
10%
10%
10%
10%
50V
50V
50V
50V
50V
Remark
IC103
IC104
IC105
IC106
IC201
8-759-161-75
8-759-523-02
8-759-648-65
8-759-358-47
8-759-666-25
IC
IC
IC
IC
IC
NJM2112V(TE2)
TC74HC4053AFT(E)
AD1855JRSRL
NJM2115V(TE2)
uPD784215GC-153-8EU
C351
C352
C353
C354
C355
1-115-339-11
1-130-493-00
1-115-339-11
1-115-339-11
1-163-009-11
CERAMIC CHIP
MYLAR
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.068uF
0.1uF
0.1uF
0.001uF
10%
5%
10%
10%
10%
50V
50V
50V
50V
50V
IC204
IC301
IC302
IC303
IC304
8-759-526-81
8-759-643-42
8-759-582-38
8-759-491-47
8-759-648-13
IC
IC
IC
IC
IC
RN5VL42AA-TL
CXD9511AQ
XCB56362PV100
TC74VHCT08AFT(EL)
YM3436D
C360
C361
C362
C363
C364
1-124-584-11
1-115-339-11
1-115-339-11
1-163-100-00
1-163-100-00
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100uF
0.1uF
0.1uF
20PF
20PF
20%
10%
10%
5%
5%
6.3V
50V
50V
50V
50V
IC305
IC306
IC307
IC801
IC802
8-749-923-05
8-759-196-96
8-759-082-57
8-759-158-77
8-759-471-81
IC
IC
IC
IC
IC
TORX178 (DIGITAL IN)
TC7SH08FU-TE85R
TC7W04FU
TA78057S(LBSONY)
PQ05RD11
C365
C366
C367
C368
C369
1-115-339-11
1-124-584-11
1-163-017-00
1-115-339-11
1-115-339-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
100uF
0.0047uF
0.1uF
0.1uF
10%
20%
5%
10%
10%
50V
6.3V
50V
50V
50V
IC803
IC804
IC805
8-759-445-59 IC BA033T
8-759-459-99 IC PQ09RD11
8-759-459-99 IC PQ09RD11
C380
C800
C801
C802
C803
1-163-117-00
1-128-548-11
1-115-339-11
1-126-382-11
1-163-038-00
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
100PF
4700uF
0.1uF
100uF
0.1uF
5%
20%
10%
20%
50V
25V
50V
16V
25V
J101
J801
C806
C807
C808
C809
C810
1-163-038-00
1-163-038-00
1-126-382-11
1-115-339-11
1-124-584-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
0.1uF
0.1uF
100uF
0.1uF
100uF
C811
C812
C813
C816
1-163-038-00
1-163-038-00
1-124-584-11
1-126-382-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
0.1uF
0.1uF
100uF
100uF
< CONNECTOR >
* CN101
CN102
CN103
1-568-955-11 PIN, CONNECTOR 6P
1-691-044-11 HOUSING, CONNECTOR 12P
1-691-038-31 HOUSING, CONNECTOR 6P
< DIODE >
D1
D51
D101
D102
D103
8-719-939-02
8-719-939-02
8-719-421-59
8-719-421-59
8-719-988-61
DIODE
DIODE
DIODE
DIODE
DIODE
SVC203CP
SVC203CP
MA3130WA-TX
MA3130WA-TX
1SS355TE-17
D104
D201
D202
8-719-421-59 DIODE MA3130WA-TX
8-719-210-33 DIODE EC10DS2
8-719-210-33 DIODE EC10DS2
< IC >
IC101
IC102
8-759-100-96 IC uPC4558G2
8-759-490-70 IC PCM3001E-T2
20%
10%
20%
25V
25V
16V
50V
6.3V
20%
20%
25V
25V
6.3V
16V
Ref. No.
Remark
< JACK >
1-784-653-11 JACK, PHONO 2P (LINE INPUT)
1-785-066-11 JACK, DC (POLARITY UNIFIED TYPE) (DC IN 9V)
< COIL >
L1
L2
L51
L52
L101
1-409-693-11
1-412-961-11
1-409-692-11
1-412-962-11
1-412-953-11
COIL (OSC)
INDUCTOR
COIL (OSC)
INDUCTOR
INDUCTOR
L102
L103
L104
L105
L106
1-412-953-11
1-414-234-22
1-414-235-22
1-414-235-22
1-414-235-22
INDUCTOR
15uH
FERRITE BEAD INDUCTOR
FERRITE BEAD INDUCTOR
FERRITE BEAD INDUCTOR
FERRITE BEAD INDUCTOR
L107
L150
L151
L152
L201
1-412-953-11
1-412-953-11
1-412-953-11
1-412-953-11
1-412-953-11
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
L203
L301
L302
L303
L304
1-414-235-22
1-412-953-11
1-416-668-11
1-414-234-22
1-414-234-22
FERRITE BEAD INDUCTOR
INDUCTOR
15uH
INDUCTOR
10uH
FERRITE BEAD INDUCTOR
FERRITE BEAD INDUCTOR
L305
L306
L307
L308
L310
1-414-234-22
1-414-234-22
1-414-234-22
1-414-234-22
1-412-953-11
FERRITE BEAD INDUCTOR
FERRITE BEAD INDUCTOR
FERRITE BEAD INDUCTOR
FERRITE BEAD INDUCTOR
INDUCTOR
15uH
L315
L330
L331
L332
1-414-234-22
1-416-668-11
1-414-234-22
1-414-234-22
FERRITE BEAD INDUCTOR
INDUCTOR
10uH
FERRITE BEAD INDUCTOR
FERRITE BEAD INDUCTOR
– 42 –
68uH
82uH
15uH
15uH
15uH
15uH
15uH
15uH
TX
Ref. No.
Part No.
Description
Part No.
Description
L333
L360
L361
L362
L363
1-412-953-11
1-412-953-11
1-414-234-22
1-414-234-22
1-414-234-22
INDUCTOR
15uH
INDUCTOR
15uH
FERRITE BEAD INDUCTOR
FERRITE BEAD INDUCTOR
FERRITE BEAD INDUCTOR
Remark
R105
R106
R109
R110
R111
1-216-081-00
1-216-081-00
1-216-072-00
1-216-072-00
1-216-081-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
22K
22K
9.1K
9.1K
22K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
L364
L365
L366
L367
L368
1-414-234-22
1-414-234-22
1-414-234-22
1-412-953-11
1-414-234-22
FERRITE BEAD INDUCTOR
FERRITE BEAD INDUCTOR
FERRITE BEAD INDUCTOR
INDUCTOR
15uH
FERRITE BEAD INDUCTOR
R112
R113
R114
R115
R116
1-216-081-00
1-216-089-11
1-216-089-11
1-216-081-00
1-216-057-00
METAL CHIP
RES,CHIP
RES,CHIP
METAL CHIP
METAL CHIP
22K
47K
47K
22K
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
L801
L802
1-469-349-11 INDUCTOR
1-416-668-11 INDUCTOR
R117
R118
R119
R120
R121
1-216-057-00
1-216-089-11
1-216-089-11
1-216-049-11
1-216-065-11
METAL CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
2.2K
47K
47K
1K
4.7K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R122
R124
R125
R130
R131
1-216-089-11
1-216-021-00
1-216-039-00
1-216-074-00
1-216-074-00
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
68
390
11K
11K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R134
R135
R136
R137
R138
1-216-025-11
1-216-025-11
1-216-073-00
1-216-073-00
1-216-073-00
RES,CHIP
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
10K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R139
R150
R160
R161
R162
1-216-073-00
1-216-296-00
1-216-067-00
1-216-067-00
1-216-082-00
METAL CHIP
SHORT
METAL CHIP
METAL CHIP
RES,CHIP
10K
0
5.6K
5.6K
24K
5%
1/10W
5%
5%
5%
1/10W
1/10W
1/10W
R163
R164
R165
R231
R232
1-216-082-00
1-216-082-00
1-216-082-00
1-216-065-11
1-216-089-11
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
24K
24K
24K
4.7K
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R301
R302
R303
R304
R305
1-216-073-00
1-216-039-00
1-216-039-00
1-216-039-00
1-216-039-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
390
390
390
390
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R306
R307
R330
R333
R335
1-216-039-00
1-216-039-00
1-216-073-00
1-216-073-00
1-216-073-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
390
390
10K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R337
R339
R341
R342
R344
1-216-073-00
1-216-073-00
1-216-039-00
1-216-039-00
1-216-073-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
390
390
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R360
R361
R362
1-216-121-11 RES,CHIP
1-216-039-00 METAL CHIP
1-216-061-00 METAL CHIP
1M
390
3.3K
5%
5%
5%
1/10W
1/10W
1/10W
1uH
10uH
< LINE FILTER >
LF101
LF801
1-403-601-21 FILTER, COMMON MODE
1-416-846-21 COIL, LINE FILTER
< TRANSISTOR >
Q1
Q2
Q51
Q52
Q101
8-729-920-38
8-729-216-22
8-729-920-38
8-729-216-22
1-801-806-11
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC2059K-N
2SA1162-G
2SC2059K-N
2SA1162-G
DTC144EKA-T146
Q102
1-801-806-11 TRANSISTOR DTC144EKA-T146
< RESISTOR >
R7
R8
R9
R10
R11
1-216-061-00
1-216-063-11
1-216-063-11
1-216-081-00
1-216-107-00
METAL CHIP
RES,CHIP
RES,CHIP
METAL CHIP
METAL CHIP
3.3K
3.9K
3.9K
22K
270K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R12
R13
R14
R15
R16
1-216-025-11
1-216-057-00
1-216-747-11
1-216-596-11
1-216-047-11
RES,CHIP
METAL CHIP
METAL CHIP
RES,CHIP
RES,CHIP
100
2.2K
33K
2.7K
820
5%
5%
1%
1%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R30
R33
R57
R58
R59
1-216-049-11
1-216-049-11
1-216-057-00
1-216-063-11
1-216-063-11
RES,CHIP
RES,CHIP
METAL CHIP
RES,CHIP
RES,CHIP
1K
1K
2.2K
3.9K
3.9K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R60
R61
R62
R63
R64
1-216-081-00
1-216-107-00
1-216-025-11
1-216-057-00
1-216-747-11
METAL CHIP
METAL CHIP
RES,CHIP
METAL CHIP
METAL CHIP
22K
270K
100
2.2K
33K
5%
5%
5%
5%
1%
1/10W
1/10W
1/10W
1/10W
1/10W
R65
R66
R101
R102
R103
1-216-596-11
1-216-047-11
1-216-117-00
1-216-117-00
1-216-089-11
RES,CHIP
RES,CHIP
METAL CHIP
METAL CHIP
RES,CHIP
2.7K
820
680K
680K
47K
1%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R104
1-216-089-11 RES,CHIP
47K
5%
1/10W
Ref. No.
– 43 –
Remark
DP-IF5100
TX
Ref. No.
Part No.
Description
R363
R364
R365
R366
R367
1-216-025-11
1-216-039-00
1-216-039-00
1-216-039-00
1-216-039-00
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
390
390
390
390
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
Remark
R368
R369
R805
R806
1-216-039-00
1-216-039-00
1-216-073-00
1-216-073-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
390
390
10K
10K
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
< CERMET RESISTOR >
RV1
RV51
1-241-762-11 RES, ADJ, CERMET 2.2K
1-241-762-11 RES, ADJ, CERMET 2.2K
< SWITCH >
S101
1-554-574-21 SWITCH, SLIDE (ATT)
< VIBRATOR >
X201
1-760-599-11 VIBRATOR, CERAMIC (8MHz)
X301
1-767-878-11 VIBRATOR, CRYSTAL (12.288MHz)
*************************************************************
MISCELLANEOUS
***************
9
10
1-790-200-11 WIRE, PARALLEL 12P
1-790-199-11 WIRE, PARALLEL 6P
Sony Corporation
9-927-602-12
Personal Audio Division Company
– 44 –
2000B0464-1
Printed in Japan C2000. 2
Published by General Engineering Dept.