Download Visual Performance Extreme Manual

SONANCE VISUAL PERFORMANCE ® EXTREME SPEAKERS
VP65R XT
Tweeter:
Woofer:
RotoLock
Screws
FIGURE 6: TIGHTENING
THE
ROTOLOCK SCREWS
• When you notice resistance on the screws the speaker has
been clamped successfully.
I M P O R TA N T : A L WAY S
NEVER OVER-TIGHTEN.
N OTE : A DJUSTING
USE
LOW-TORQUE
THE TENSION OF THE
R OTO L OCK
SETTINGS;
CLAMPS SO
Frequency Response:
Impedance:
Power Handling:
Sensitivity:
Grille Material:
Dimensions (Dia x D):
Cutout Dimensions (Dia):
Shipping Weight:
VP65S XT
Tweeter:
Woofer:
THAT THE SPEAKER FRAME IS FLAT WILL HELP ENSURE THAT THE GRILLE
CONTACTS THE WALL ALL THE WAY AROUND THE SPEAKER FOR A
PROPER FIT.
7. The new micro-trim grille is held in place by several small,
powerful magnets on the rear of the grille. Place the grille
against the speaker and the magnets will hold it firmly in
place. When the grille is properly installed, the grille trim
should make contact with the mounting surface all the way
around the speaker.
1" (25mm) polyurethane dome
6½" (165mm) injection-molded
polypropylene/graphite cone, with
integral Santoprene® surround
55Hz – 20kHz ±3dB
8 ohms nominal; 6 ohms minimum
5 watts minimum; 130 watts maximum
89dB SPL (2.83V/1 meter)
Powder-coated stainless steel
9¾” x 3½” (248mm x 89mm)
8¼” (210mm)
12 lbs (5.4kg) pair
Frequency Response:
Impedance:
Power Handling:
Sensitivity:
Grille Material:
Dimensions (H x W x D):
Cutout Dim. (W x H):
Shipping Weight:
1" (25mm) polyurethane dome
6½" (165mm) injection-molded
polypropylene/graphite cone, with
integral Santoprene surround
55Hz – 20kHz ±3dB
8 ohms nominal; 6 ohms minimum
5 watts minimum; 130 watts maximum
89dB (SPL 2.83V/1 meter)
Powder-coated stainless steel
97/8" x 97/8” x 3½"
(251mm x 251mm x 89mm)
8¼" x 8¼" (210mm x 210mm)
12 lbs. (5.4kg) pair
Painting the Grilles
See the accompanying instruction sheet for painting instructions.
VP65R SST XT
Environmental Specifications
Tweeter:
Woofer:
Maximum Heat:
Maximum Cold:
Maximum Humidity:
+175°F (+79°C)
–30°F (–34°C)
99% (120°F/49°C)
95% (–30°F/–34°C)
These speakers meet or exceed the following:
Salt Spray:
ASTM-B117
UV Test:
ASTM-G23H
IEC/CEE
Water Splashing Test:
IP-X4
Vibration Test:
ASTM D5112-98 and ASTM D3580-95
Frequency Response:
Impedance:
Power Handling:
Sensitivity:
Grille Material:
Dimensions (Dia x D):
Cutout Dimensions (Dia):
Shipping Weight:
Two 1" (25mm) polyurethane domes
6½" (165mm) injection-molded
polypropylene/graphite cone, with
integral Santoprene® surround, dual
voice coil
55Hz – 20kHz ±3dB
8 ohms nominal; 6 ohms minimum
5 watts minimum; 130 watts maximum
89dB SPL (2.83V/1 meter)
Powder-coated stainless steel
9¾” x 5 3/16” (248mm x 132mm)
8¼” (210mm)
4.5 lbs (2.1kg) each
Performance Specifications
VP65 XT
Tweeter:
Woofer:
1" (25mm) polyurethane dome
6½" (165mm) injection-molded
polypropylene/graphite cone, with
integral Santoprene® surround
Frequency Response:
55Hz – 20kHz ±3dB
Impedance:
8 ohms nominal; 6 ohms minimum
Power Handling:
5 watts minimum; 130 watts maximum
Sensitivity:
89dB SPL (2.83V/1 meter)
Grille Material:
Powder-coated stainless steel
Dimensions (W x H x D): 83/8" x 12¼" x 2½”
(213mm x 311mm x 64mm)
Cutout Dimensions (W x H): 615/16” x 10¾" (176mm x 273mm)
Shipping Weight:
12 lbs (5.4kg) pair
3