Download Toshiba 27A51 27" TV - C:\Documents and Settings\Owner\My Documents\Toshiba Repair Guide27A51[1]
Transcript
FILE NO. 050-200113 SERVICE MANUAL COLOR TELEVISION 27A51 SERVICING NOTICES ON CHECKING 1. KEEP THE NOTICES 6. AVOID AN X-RAY As for the places which need special attentions, they are indicated with the labels or seals on the cabinet, chassis and parts. Make sure to keep the indications and notices in the operation manual. 2. AVOID AN ELECTRIC SHOCK There is a high voltage part inside. Avoid an electric shock while the electric current is flowing. 3. USE THE DESIGNATED PARTS The parts in this equipment have the specific characters of incombustibility and withstand voltage for safety. Therefore, the part which is replaced should be used the part which has the same character. Especially as to the important parts for safety which is indicated in the circuit diagram or the table of parts as a mark, the designated parts must be used. 4. PUT PARTS AND WIRES IN THE ORIGINAL POSITION AFTER ASSEMBLING OR WIRING Safety is secured against an X-ray by considering about the cathode-ray tube and the high voltage peripheral circuit, etc. Therefore, when repairing the high voltage peripheral circuit, use the designated parts and make sure not modify the circuit. Repairing except indicates causes rising of high voltage, and it emits an X-ray from the cathoderay tube. 7. PERFORM A SAFETY CHECK AFTER SERVICING Confirm that the screws, parts and wiring which were removed in order to service are put in the original positions, or whether there are the portions which are deteriorated around the serviced places serviced or not. Check the insulation between the antenna terminal or external metal and the AC cord plug blades. And be sure the safety of that. (INSULATION CHECK PROCEDURE) There are parts which use the insulation material such as a tube or tape for safety, or which are assembled in the condition that these do not contact with the printed board. The inside wiring is designed not to get closer to the pyrogenic parts and high voltage parts. Therefore, put these parts in the original positions. 5. TAKE CARE TO DEAL WITH THE CATHODE-RAY TUBE 1. Unplug the plug from the AC outlet. 2. Remove the antenna terminal on TV and turn on the TV. 3. Insulation resistance between the cord plug terminals and the eternal exposure metal [Note 2] should be more than 1M ohm by using the 500V insulation resistance meter [Note 1]. 4. If the insulation resistance is less than 1M ohm, the inspection repair should be required. [Note 1] In the condition that an explosion-proof cathoderay tube is set in this equipment, safety is secured against implosion. However, when removing it or serving from backward, it is dangerous to give a shock. Take enough care to deal with it. If you have not the 500V insulation resistance meter, use a Tester. [Note 2] External exposure metal: Antenna terminal Earphone jack HOW TO ORDER PARTS Please include the following informations when you order parts. (Particularly the VERSION LETTER.) 1. MODEL NUMBER and VERSION LETTER The MODEL NUMBER can be found on the back of each product and the VERSION LETTER can be found at the end of the SERIAL NUMBER. 2. PART NO. and DESCRIPTION You can find it in your SERVICE MANUAL. IMPORTANT Inferior silicon grease can damage IC's and transistors. When replacing an IC's or transistors, use only specified silicon grease (YG6260M). Remove all old silicon before applying new silicon. GENERAL SPECIFICATIONS G-1 TV System CRT CRT Size / Visual Size CRT Type Deflection Magnetic Field BV/BH 27 inch / 676mmV Normal 102 degree +0.45G/0.18G NTSC 2Speaker Front 2.0 x 3.5 Inch 8 ohm 2.5 + 2.5 W 2.0 + 2.0 W No US System M 1Tuner Ohers F-Synth VHF/UHF 75 ohm 2 - 69, 4A, A-5 - A-1, A - I, J - W, W+1 - W+84 45.75MHz 41.25MHz 4.50MHz No Yes Yes 120V AC 60Hz - Color System Speaker Sound Output G-2 Tuning System NTSC3.58+4.43 /PAL60Hz Broadcasting System Tuner and Receive CH Intermediate Frequency G-3 Power Preset CH Stereo/Dual TV Sound Tuner Sound Muting Power Source Position Size Impedance MAX 10%(Typical) System Destination Tuning System Input Impedance CH Coverage Picture(FP) Sound(FS) FP-FS AC DC Power Consumption Protector G-4 Regulation G-5 Temperature G-6 Operating Humidity at AC Stand by (at AC) Per Year Power Fuse Safety Radiation X-Radiation Operation Storage 125 W at AC 120 V 60 Hz 4 W at AC 120 V 60 Hz -kWh/Year Yes UL FCC DHHS +5oC ~ +40oC -20oC ~ +60oC Less then 80% RH GENERAL SPECIFICATIONS G-7 On Screen Display Menu Menu Type Picture Contrast Brightness Color Tint Sharpness Audio Bass Treble Balance BBE On/Off Stable Sound On/Off Set Up PIP SOURCE TV/CABLE(CATV) CH Program Add/Erase Option Language V-chip CH Label Favorite CH Color Stream DVD/DTV Control Level Volume Brightness Contrast Color Tint (NTSC Only) Sharpness Tuning Bass Treble Balance Back Light Stereo,Audio Output,SAP Video Color Stream Channel(TV/Cable) CH Label Sleep Timer Sound Mute P-in-P V-chip Rating G-8 G-9 OSD Language Clock and Timer Sleep Timer OSD Language Setting Max Time Step Program(On Tim / Off Tim) On/Off Timer Wake Up Timer Timer Back-up (at Power Off Mode) more than Yes Icon Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No Yes Yes Yes No Yes Yes Yes Yes Yes Yes Yes Yes Yes English French English 120 Min 10 Min No No -Min Spanish Sec GENERAL SPECIFICATIONS G-10 Remote Control Unit Glow in Dark Remocon Format Custom Code Power Source Total Keys Keys P-in-P Keys 2 Tuner P-in-P Only Multi Brand Keys Voltage(D.C) UM size x pcs Power 1 2 3 4 5 6 7 8 9 0 100 CH Up CH Down Volume Up Volume Down TV/Caption/Text CH1/CH2 TV/Video(TV/AV) CH RTN/CH ENT(Quick View) Sleep RE Call(Call) Reset Menu/Enter Mute Exit MTS(Audio Select) Fav.Up Fav.Down Set + Set PIP Swap Locate Still PIP CH Up PIP CH Down CH Up(VCR) CH Down(VCR) Pause/Still TV/VCR(VCR) Code FF Rew Rec Play Stop TV VCR Cable RC-DU Yes Toshiba TV:40-BF h 3V UM-4 x 2 pcs 46 Keys Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No No Yes Yes Yes Yes No No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes GENERAL SPECIFICATIONS G-11 Features Auto Degauss Auto Shut Off Canal+ CATV Anti-theft Rental Memory(Last CH) Memory(Last Volume) V-Chip Yes Yes No Yes No No Type BBE Auto Search CH Allocation SAP Channel Lock Just Clock Function Game Position CH Label VM Circuit Full OSD Premiere Comb Filter G-12 Accessories Auto CH Memory Hotel Lock Closed Caption Stable Sound FBT Leak Test Protect Favorite CH 1 Tuner P-in-P 2 Tuner P-in-P Owner's Manual Language W/ Warranty Remote Control Unit Rod Antenna Yes Yes Yes USA,Toshiba Type No No No Yes No No No Yes No No No Yes 2 Lines Yes No Yes Yes Yes Yes Yes No English Yes Yes No Poles Terminal Loop Antenna No Terminal U/V Mixer DC Car Cord (Center+) Guarantee Card Warning Sheet Circuit Diagram Antenna Change Plug Service Facility List Important Safety Instruction Dew/AHC Caution Sheet AC Plug Adapter Quick Set-up Sheet Battery No No No No No No No Yes No No No UM size x pcs OEM Brand AC Cord AV Cord (2Pin-1Pin) Registration Card (NDL Card) ESP Card PTB Sheet 300 ohm to 75 ohm Antenna Adapter Yes UM4 size x 2 No No No Yes Yes No No GENERAL SPECIFICATIONS G-13 Interface Switch Front Rear Indicator Terminals Front Rear G-14 G-15 Set Size Weight G-16 Carton Power System Select Main Power SW Sub Power Channel Up Channel Down Volume Up Volume Down AC/DC TV/CATV Selector Degauss Main Power SW Power Stand-by On Timer Video Input Audio Input Other Terminal Video Input(Rear1) Video Input(Rear2) Audio Input(Rear1) Audio Input(Rear2) Video Output Audio Output S- Input Euro Scart Color Stream Diversity Ext Speaker DC Jack 12V(Center +) VHF/UHF Antenna Input AC Outlet Approx. W x D x H (mm) Net (Approx.) Gross (Approx.) Master Carton Content Material Dimensions W x D x H(mm) Description of Origin Gift Box Material Dimensions W x D x H(mm) Design Description of Origin Drop Test G-17 Cabinet Material Height (cm) Container Stuffing Cabinet Front Cabinet Rear Yes No No No Yes Yes Yes Yes No No No No Yes No No RCA RCA x 2 No RCA RCA RCA x 2 RCA x 2 RCA RCA x 2 Yes No RCA x 3 No No No F Type No 650 x 500.5 x 560 35kg ( 77.1 lbs) 38Kg ( 83.7 lbs) No ---Sets -/--- x -- x -No Yes Double/Brown 718 x 580 x 655 As per Buyer's Yes Natural Dropping At 1 Corner / 3 Edges / 6 Surfaces 31 192 Sets/40' container PS 94V0 DECABROM PS 94V0 DISASSEMBLY INSTRUCTIONS 3. After one side is removed, pull in the opposite direction to remove the other. 1. REMOVAL OF ANODE CAP Read the following NOTED items before starting work. * After turning the power off there might still be a potential voltage that is very dangerous. When removing the Anode Cap, make sure to discharge the Anode Cap's potential voltage. * Do not use pliers to loosen or tighten the Anode Cap terminal, this may cause the spring to be damaged. NOTE Take care not to damage the Rubber Cap. INSTALLATION 1. Clean the spot where the cap was located with a small amount of alcohol. (Refer to Fig. 1-3.) REMOVAL 1. Follow the steps as follows to discharge the Anode Cap. (Refer to Fig. 1-1.) Connect one end of an Alligator Clip to the metal part of a flat-blade screwdriver and the other end to ground. While holding the plastic part of the insulated Screwdriver, touch the support of the Anode with the tip of the Screwdriver. A cracking noise will be heard as the voltage is discharged. Location of Anode Cap GND on the CRT Fig. 1-3 NOTE Confirm that there is no dirt, dust, etc. at the spot where the cap was located. 2. Arrange the wire of the Anode Cap and make sure the wire is not twisted. 3. Turn over the Rubber Cap. (Refer to Fig. 1-4.) CRT Screwdriver Support Alligator Clip GND on the CRT Fig. 1-1 2. Flip up the sides of the Rubber Cap in the direction of the arrow and remove one side of the support. (Refer to Fig. 1-2.) Fig. 1-4 4. Insert one end of the Anode Support into the anode button, then the other as shown in Fig. 1-5. Rubber Cap CRT Support Fig. 1-2 CRT Support Fig. 1-5 5. Confirm that the Support is securely connected. 6. Put on the Rubber Cap without moving any parts. DISASSEMBLY INSTRUCTIONS 2. REMOVAL AND INSTALLATION OF FLAT PACKAGE IC REMOVAL 3. When IC starts moving back and forth easily after desoldering completely, pickup the corner of the IC using a tweezers and remove the IC by moving with the IC desoldering machine. (Refer to Fig. 2-3.) NOTE 1. Put the Masking Tape (cotton tape) around the Flat Package IC to protect other parts from any damage. (Refer to Fig. 2-1.) Some ICs on the PCB are affixed with glue, so be careful not to break or damage the foil of each IC leads or solder lands under the IC when removing it. NOTE Masking is carried out on all the parts located within 10 mm distance from IC leads. Masking Tape (Cotton Tape) Blower type IC desoldering machine IC Tweezers Fig. 2-1 IC Fig. 2-3 2. Heat the IC leads using a blower type IC desoldering machine. (Refer to Fig. 2-2.) 4. Peel off the Masking Tape. NOTE Do not add the rotating and the back and forth directions force on the IC, until IC can move back and forth easily after desoldering the IC leads completely. 5. Absorb the solder left on the pattern using the Braided Shield Wire. (Refer to Fig. 2-4.) NOTE Do not move the Braided Shield Wire in the vertical direction towards the IC pattern. Blower type IC desoldering machine Braided Shield Wire Soldering Iron IC Fig. 2-2 IC pattern Fig. 2-4 DISASSEMBLY INSTRUCTIONS INSTALLATION 1. Take care of the polarity of new IC and then install the new IC fitting on the printed circuit pattern. Then solder each lead on the diagonal positions of IC temporarily. (Refer to Fig. 2-5.) 4. When bridge-soldering between terminals and/or the soldering amount are not enough, resolder using a Thintip Soldering Iron. (Refer to Fig. 2-8.) Thin-tip Soldering Iron IC Soldering Iron Fig. 2-8 Solder temporarily Solder temporarily Fig. 2-5 2. Supply the solder from the upper position of IC leads sliding to the lower position of the IC leads. (Refer to Fig. 2-6.) Solder IC Soldering Iron Supply soldering from upper position to lower position Fig. 2-6 3. Absorb the solder left on the lead using the Braided Shield Wire. (Refer to Fig. 2-7.) NOTE Do not absorb the solder to excess. Soldering Iron IC Braided Shield Wire Fig. 2-7 5. Finally, confirm the soldering status on four sides of the IC using a magnifying glass. Confirm that no abnormality is found on the soldering position and installation position of the parts around the IC. If some abnormality is found, correct by resoldering. NOTE When the IC leads are bent during soldering and/or repairing, do not repair the bending of leads. If the bending of leads are repaired, the pattern may be damaged. So, be always sure to replace the IC in this case. SERVICE MODE LIST This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily. To enter the Service Mode, press both set key and remote control key for more than 1 second. Set Key Remocon Key VOL. (-) MIN 0 Releasing of V-CHIP PASSWORD. Operations VOL. (-) MIN 1 Initialization of the factory. NOTE: Do not use this for the normal servicing. POWER ON total hours is displayed on the screen. Refer to the "CONFIRMATION OF USING HOURS". VOL. (-) MIN 6 Can be checked of the INITIAL DATA of MEMORY IC. Refer to the "NOTE FOR THE REPLACING OF MEMORY IC". VOL. (-) MIN 8 Writing of EEPROM initial data. NOTE: Do not use this for the normal servicing. VOL. (-) MIN 9 Display of the Adjustment MENU on the screen. Refer to the "ELECTRICAL ADJUSTMENT" (On-Screen Display Adjustment). CONFIRMATION OF USING HOURS POWER ON total hours can be checked on the screen. Total hours are displayed in 16 system of notation. ADDRESS 1. Set the VOLUME to minimum. 2. Press both VOL. DOWN button on the set and Channel button (6) on the remote control for more than 1 second. 3. After the confirmation of using hours, turn off the power. INIT 00 CRT ON DATA Initial setting content of MEMORY IC. 83 POWER ON total hours. 0010 = (16 x 16 x 16 x thousands digit value) + (16 x 16 x hundreds digit value) + (16 x tens digit value) + (ones digit value) FIG. 1 NOTE FOR THE REPLACING OF MEMORY IC If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be taken to ensure correct data settings while making reference to TABLE 1. INI +0 +1 +2 +3 +4 +5 +6 +7 +8 +9 +A +B +C +D +E +F 00 A9 C3 37 30 31 B3 27 17 2B 80 F4 C4 00 00 00 5F 10 0F 00 89 28 80 27 40 83 43 00 10 0E 61 63 64 26 20 67 69 2A 6B 6C 6D 6E 6F 70 71 52 72 53 73 54 74 30 55 75 75 56 56 76 76 57 57 77 77 58 58 78 78 59 40 59 79 79 5A 5A 7A 7A 5B 5B 7B 7B 5C 5C 7C 7C 5D 50 5D 7D 7D 5E 5E 7E 7E 5F 5F 5F 7F 7F --- --- --- --- Table 1 1. Enter DATA SET mode by setting VOLUME to minimum. 2. Press both VOL. DOWN button on the set and Channel button (6) on the remote control for more than 1 second. ADDRESS and DATA should appear as FIG 1. 3. ADDRESS is now selected and should "blink". Using the VOL. UP/DOWN button on the remote, step through the ADDRESS until required ADDRESS to be changed is reached. 4. Press ENTER to select DATA. When DATA is selected, it will "blink". 5. Again, step through the DATA using VOL. UP/DOWN button until required DATA value has been selected. 6. Pressing ENTER will take you back to ADDRESS for further selection if necessary. 7. Repeat steps 3 to 6 until all data has been checked. 8. When satisfied correct DATA has been entered, turn POWER off (return to STANDBY MODE) to finish DATA input. The unit will now have the correct DATA for the new MEMORY IC. ELECTRICAL ADJUSTMENTS 1. BEFORE MAKING ELECTRICAL ADJUSTMENTS 2. BASIC ADJUSTMENTS Read and perform these adjustments when repairing the circuits or replacing electrical parts or PCB assemblies. 1. Set condition is AV MODE without signal. 2. Connect the digital voltmeter to TP002. 3. Adjust the VR502 until the digital voltmeter is 135 ± 0.5V. 2-1: CONSTANT VOLTAGE CAUTION • Use an isolation transformer when performing any service on this chassis. • Before removing the anode cap, discharge electricity because it contains high voltage. • When removing a PCB or related component, after unfastening or changing a wire, be sure to put the wire back in its original position. Inferior silicon grease can damage IC's and transistors. • When replacing IC's and transistors, use only specified silicon grease. Remove all old silicon before applying new silicon. Prepare the following measurement tools for electrical adjustments. 1. Oscilloscope 2. Digital Voltmeter 3. AC Voltmeter On-Screen Display Adjustment 1. In the condition of NO indication on the screen. Press the VOL. DOWN button on the set and the Channel button (9) on the remote control for more than 1 second to appear the adjustment mode on the screen as shown in Fig. 1-1. TV 00 OSD 15 Fig. 1-1 2. Use the Channel UP/DOWN button or Channel button (0-9) on the remote control to select the options shown in Fig. 1-2. 3. Press the MENU button on the remote control to end the adjustments. NO. 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 FUNCTION OSD H CUT OFF RF. AGC --H. POSI V. POSI H. SIZE V. SIZE V. CENT V. LIN VS. CORR G. DRV B. DRV R. BIAS G. BIAS B. BIAS BRI SUBCONT UNI COL --TINT SHARP RGB CONT PARABOLA NO. 24 25 26 27 28 29 30 31 32 33 35 36 37 38 39 40 41 42 43 44 45 46 47 48 FUNCTION TRAPEZIU COR TOP COR BTM V EHT H EHT FM. LVL LEVEL SEP1 SEP2 T. STE V POS U V POS L H POS L H POS R H. SIZE V. SIZE H. POSI R G B BRI COL TINT VCO 2-2: RF AGC 1. Receive the VHF LOW (61dB). 2. Connect the digital voltmeter between the TP001 and the GND. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (02) on the remote control to select "RF. AGC". 4. Press the VOL. UP/DOWN button on the remote control until the digital voltmeter is 2.4V. 2-3: CUT OFF 1. Adjust the unit to the following settings. G. DRIVE=64, B. DRIVE=64, R. BIAS=15, G. BIAS=15, B. BIAS=15, BRIGHT=75, UNI COLOR=64 2. Place the set with Aging Test for more than 15 minutes. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (01) on the remote control to select "CUT OFF". 4. Adjust the Screen Volume until a dim raster is obtained. 2-4: WHITE BALANCE NOTE: Adjust after performing CUT OFF adjustment. 1. Place the set with Aging Test for more than 10 minutes. 2. Receive the white 100% signal from the Pattern Generator. 3. Using the adjustment control, set the brightness and contrast to normal position. 4. Activate the adjustment mode display of Fig. 1-1 and press the channel button (13) on the remote control to select "R. BIAS". 5. Using the VOL. UP/DOWN button on the remote control, adjust the R. BIAS. 6. Press the CH. UP/DOWN button on the remote control to select the "G. DRV", "B. DRV", "G. BIAS" or "B. BIAS". 7. Using the VOL. UP/DOWN button on the remote control, adjust the G. DRV, B. DRV, G. BIAS or B. BIAS. 8. Perform the above adjustments 6 and 7 until the white color is looked like a white. 2-5: FOCUS 1. Receive a 70dB monoscope pattern. 2. Turn the Focus Volume fully counterclockwise once. 3. Adjust the Focus Volume until picture is distinct. 2-6: HORIZONTAL POSITION 1. Receive the center cross signal from the Pattern Generator. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (04) on the remote control to select "H. POSI". 4. Press the VOL. UP/DOWN button on the remote control until the right and left screen size of the vertical line becomes the same. Fig. 1-2 ELECTRICAL ADJUSTMENTS 2-7: VERTICAL LINEARITY 2-12: SEPARATION 1, 2 NOTE: Adjust after performing adjustments in section 2-6. 1. Receive the stereo signal (L=2KHz, R=400Hz). 2. Connect the AC voltmeter to AUDIO OUT JACK though stereo filter (L=400Hz, R=2KHz). 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (31) on the remote control to select "SEP1". 4. Press the VOL. UP/DOWN button on the remote control until the output of L-CH and R-CH become minimum. 5. Press the CH UP button once the set to "SEP2" mode. 6. Press the VOL. UP/DOWN button on the remote control until the output of L-CH and R-CH become minimum. 7. Press the CH DOWN button once the set to "SEP1" mode. 8. Repeat step 4 to step 7 several times. The output difference of the between with Filter and without Filter should be more than 25dB for both L and R. 2-13: BRIGHTNESS 1. Receive the center cross signal from the Pattern Generator. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (09) on the remote control to select "V. LIN". 4. Press the VOL. UP/DOWN button on the remote control until the upside and downside screen size of the horizontal line becomes the same. 2-8: VERTICAL POSITION NOTE: Adjust after performing adjustments in section 2-7. 1. Receive the center cross signal from the Pattern Generator. 2. Adjust the VR401 until the horizontal line becomes fit to the notch of the shadow mask. 2-9: VERTICAL SIZE NOTE: Adjust after performing adjustments in section 2-8. 1. Receive the crosshatch signal from the Pattern Generator. 2. Activate the adjustment mode display of Fig. 1-1 and press the channel button (07) on the remote control to select "V. SIZE". 3. Press the VOL. UP/DOWN button on the remote control until the rectangle on the center of the screen becomes square. 4. Receive a broadcast and check if the picture is normal. 2-10: OSD HORIZONTAL 1. Activate the adjustment mode display of Fig. 1-1. 2. Press the VOL. UP/DOWN button on the remote control until the difference of A and B becomes minimum. (Refer to Fig. 2-1) TV 00 OSD A 15 B Fig. 2-1 2-11: LEVEL 1. Receive the VHF HIGH (70dB). 2. Connect the AC voltmeter to TP901. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (30) on the remote control to select "LEVEL". 4. Press the VOL. UP/DOWN button on the remote control until the AC voltmeter is 75 ± 2mV. 1. Activate the adjustment mode display of Fig. 1-1 and press the channel button (16) on the remote control to select "BRI". 2. Press the VOL. UP/DOWN button on the remote control until the brightness step No. becomes "92" 3. Press the TV/VIDEO button on the remote control to set to the AV mode. Then perform the above adjustments 1~2. 4. Press the TV/VIDEO button on the remote control to set to the CS mode. 5. Activate the adjustment mode display of Fig. 1-1 and press the channel button (16) on the remote control to select "BRI". 6. Press the VOL. UP/DOWN button on the remote control until the brightness step No. becomes "90" 2-14: UNI-COLOR 1. Activate the adjustment mode display of Fig. 1-1 and press the channel button (18) on the remote control to select "UNI COL". 2. Press the VOL. UP/DOWN button on the remote control until the contrast step No. becomes "53" 3. Press the TV/VIDEO button on the remote control to set to the AV mode. Then perform the above adjustments 1~2. 4. Press the TV/VIDEO button on the remote control to set to the CS mode. 5. Activate the adjustment mode display of Fig. 1-1 and press the channel button (18) on the remote control to select "UNI COL". 6. Press the VOL. UP/DOWN button on the remote control until the contrast step No. becomes "54" ELECTRICAL ADJUSTMENTS 2-15: SUB TINT/SUB COLOR 2-17: PIP VERTICAL POSITION U 1. Receive the color bar pattern. (RF Input) 2. Connect the oscilloscope to TP806. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (20) on the remote control to select "TINT". 4. Press the VOL. UP/DOWN button on the remote control until the waveform becomes as shown in Fig. 2-2. 5. Connect the oscilloscope to TP804. 6. Press the CH DOWN button 3 times to set to "SUBCONT" mode. 7. Press the VOL. UP/DOWN button on the remote control until the red color level is adjusted to 105 ± 5% of the white level. (Refer to Fig. 2-3) 8. Receive the color bar pattern. (Audio Video Input) 9. Press the TV/VIDEO button on the remote control to set to the AV mode. Then perform the above adjustments 2~7. 10. Press the TV/VIDEO button on the remote control to set to the CS mode. 11. Activate the adjustment mode display of Fig. 1-1 and press the channel button (20) on the remote control to select "TINT". 12. Press the VOL. UP/DOWN button on the remote control to increase the step numbers by 6 steps to the AV. 13. Press the CH DOWN button 3 times to set to "SUBCONT" mode. 14. Press the VOL. UP/DOWN button on the remote control to set the same step number as the AV. 1. Receive the monoscope pattern. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (35) on the remote control to select "V. POS U". 4. Press the VOL. UP/DOWN button on the remote control until the value from the PIP screen frame to the shadow mask becomes 20(+3, -0)mm. (Refer to Fig. 2-4) Shadow mask 20mm Fig. 2-4 2-18: PIP VERTICAL POSITION L 1. Receive the monoscope pattern. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (36) on the remote control to select "V. POS L". 4. Press the VOL. UP/DOWN button on the remote control until the value from the PIP screen frame to the shadow mask becomes 20(+3, -0)mm. (Refer to Fig. 2-5) Fig. 2-2 20mm Shadow mask White 100% RED Level Fig. 2-3 2-16: PIP HORIZONTAL POSITION 1. Receive the center cross signal from the Pattern Generator. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (41) on the remote control to select "H. POSI". 4. Press the VOL. UP/DOWN button on the remote control until the right and left screen size of the vertical line becomes the same. Fig. 2-5 ELECTRICAL ADJUSTMENTS 2-19: PIP HORIZONTAL POSITION L 2-21: PIP R, G, B LEVEL 1. Receive the monoscope pattern. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (37) on the remote control to select "H. POSI". 4. Press the VOL. UP/DOWN button on the remote control until the value from the PIP screen frame to the shadow mask becomes 35(+3, -0)mm. (Refer to Fig. 2-6) 1. Set condition is TV MODE without signal. 2. Connect the oscilloscope to pin 16 of IC751. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (42) on the remote control to select "R". 4. Press the VOL. UP/DOWN button on the remote control until the waveform value becomes 0.9 ± 0.04V. (Refer to Fig. 2-8) 5. Connect the oscilloscope to pin 11 of IC751. 6. Press the CH UP button once to set to "G" mode. 7. Press the VOL. UP/DOWN button on the remote control until the waveform value becomes 0.9 ± 0.04V. (Refer to Fig. 2-8) 8. Press the VOL. DOWN button on the remote control to decrease the step numbers by 2 steps. 9. Connect the oscilloscope to pin 8 of IC751. 10. Press the CH UP button once to set to "B" mode. 11. Press the VOL. UP/DOWN button on the remote control until the waveform value becomes 0.9 ± 0.04V. (Refer to Fig. 2-8) Shadow mask 35mm Fig. 2-6 2-20: PIP HORIZONTAL POSITION R 1. Receive the monoscope pattern. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (38) on the remote control to select "H. POS R". 4. Press the VOL. UP/DOWN button on the remote control until the value from the PIP screen frame to the shadow mask becomes 35(+3, -0)mm. (Refer to Fig. 2-7) 0.9V Fig. 2-8 2-22: Confirmation of Fixed Value (Step No.) Please check if the fixed values of the each adjustment items are set correctly referring below. 35mm Shadow mask Fig. 2-7 NO. 05 06 08 10 21 22 23 24 25 26 27 28 29 39 40 45 46 47 FUNCTION V. POSI H. SIZE V. CENT VS. CORR SHARP RGB CONT PARABOLA TRAPEZIU COR TOP COR BTM V EHT H EHT FM. LVL H. SIZE V. SIZE BRIGHT COLOR TINT RF 00 00 32 12 30 19 00 00 00 00 00 00 01 55 68 31 18 27 AV --------30 --------------------31 18 30 CS --------30 --------------------------- S ------------------------------31 18 31 * To switch the AV mode of the PIP screen, press the channel button "77" on the remote control. To switch the S terminal input mode of the PIP screen, press the channel button "77" on the remote control after S terminal input. ELECTRICAL ADJUSTMENTS 3. PURITY AND CONVERGENCE ADJUSTMENTS NOTE 1. Turn the unit on and let it warm up for at least 30 minutes before performing the following adjustments. 2. Place the CRT surface facing east or west to reduce the terrestrial magnetism. 3. Turn ON the unit and demagnetize with a Degauss Coil. 3-1: STATIC CONVERGENCE (ROUGH ADJUSTMENT) 1. Tighten the screw for the magnet. Refer to the adjusted CRT for the position. (Refer to Fig. 3-1) If the deflection yoke and magnet are in one body, untighten the screw for the body. 2. Receive the green raster pattern from the color bar generator. 3. Slide the deflection yoke until it touches the funnel side of the CRT. 4. Adjust center of screen to green, with red and blue on the sides, using the pair of purity magnets. 5. Switch the color bar generator from the green raster pattern to the crosshatch pattern. 6. Combine red and blue of the 3 color crosshatch pattern on the center of the screen by adjusting the pair of 4 pole magnets. 7. Combine red/blue (magenta) and green by adjusting the pair of 6 pole magnets. 8. Adjust the crosshatch pattern to change to white by repeating steps 6 and 7. 3-2: PURITY 3-3: STATIC CONVERGENCE NOTE Adjust after performing adjustments in section 3-2. 1. Receive the crosshatch pattern from the color bar generator. 2. Combine red and blue of the 3 color crosshatch pattern on the center of the screen by adjusting the pair of 4 pole magnets. 3. Combine red/blue (magenta) and green by adjusting the pair of 6 pole magnets. 3-4: DYNAMIC CONVERGENCE NOTE Adjust after performing adjustments in section 3-3. 1. Adjust the differences around the screen by moving the deflection yoke upward/downward and right/left. (Refer to Fig. 3-2-a) 2. Insert three wedges between the deflection yoke and CRT funnel to fix the deflection yoke. (Refer to Fig. 3-2-b) RGB R G B RGB R G B UPWARD/DOWNWARD SLANT NOTE Fig. 3-2-a Adjust after performing adjustments in section 3-1. 1. Receive the green raster pattern from color bar generator. 2. Adjust the pair of 2-Y pole magnets so the magnets is at just down position. 3. Adjust the pair of 2-X pole magnets to center the color on the screen. Adjust the pair of 2-X pole magnets so the color at the ends are equally wide. 4. Move the deflection yoke backward (to neck side) slowly, and stop it at the position when the whole screen is green. 5. Confirm red and blue colors. 6. Adjust the slant of the deflection yoke while watching the screen, then tighten the fixing screw. DEFLECTION YOKE DEFLECTION YOKE SCREW 6 POLE MAGNETS 4 POLE MAGNETS 2-Y POLE MAGNETS 2-X POLE MAGNETS Fig. 3-1 RIGHT/LEFT SLANT WEDGE WEDGE WEDGE WEDGE POSITION Fig. 3-2-b MAJOR COMPONENTS LOCATION GUIDE VR502 IC751 (Solder side) T501 FB401 J203 J704 J703 J702 J701 VR401 TU001 TP001 TP901 TP002 FOCUS VOLUME SCREEN VOLUME MAIN PCB TP804 J801 TP806 CRT PCB TV BLOCK DIAGRAM 1 SVM SPEAKER SP1001 YOUT/R_OUT 3 SDATA VOUT/B_OUT 4 SCLK UOUT/G_OUT PIP IC1801 M65664FP CSYNCS 18 L 35 37 39 ANALOG SW IC751 MM1284 52 8 11 51 16 50 TU001 IF SDA SCL 11 5 4 R 6 2 5 7 12 SOUND AMP IC1001 AN5276 12 3 1 14 7 2 5 14 7 MICON IC101 OEC7062A OSD B 39 SCL OSD G OSD R 52 51 50 7 37 SDA 7 OSD BLK 49 1 YUV IN IF/CHROMA/AUDIO IC201 TB1253N EXT R IN EXT B IN V IN YS/YM IN SCL V OUT EXT G IN IF IN U IN 7 SDA 6 IF IN 8 24 25 43 44 22 21 20 19 18 19 14 H OUT ABCL B OUT G OUT R OUT C IN CVBSLN T IN IF DET OUT 31 34 28 16 15 14 42 47 55 21 10 SCL 22 COMB FILTER IC1501 TC90A45F B G TONE CONTROL IC303 M62420SP 9 SDA IC902 AN5829S DE-EMPH 51 FBP IN 38 PIP VIDEO SW IC750 BA7645N 4 2 24 23 18 SCL 9 17 SDA R 15 13 32 25 G B CRT V801 10 F LINE1 20 8 11 S INPUT 4 R 1 V 22 6 YUV IN 5 C 2 L AV SWITCH IC701 MM1311AD 31 R Y 6 C 3 Y 30 4 CRT DRIVE 19 27 29 14 15 13 8 10 7 L R V L R V 7 LINE2 1 5 HV V.OUTPUT IC401 LA78041 FBT FB401 S F 10 DY H. OUT Q402 Q405 7 1 6 +180V 3 +25V VIDEO3 9 POWER SW. REG. IC501 STR-G6624 4 1 T501 3 5 9 SOUND+B 12 +B D405 0 L402 R429 R409 VR401 C419 TP002 R421 R425 C417 C714 CD701A C733 W824 W070 IC750 W174 D403 W119 W127 W120 W121 C407 R408 L701 W156 4 00 C1 S104X W818 L002 C1008 TP004 R414 R413 C431 R428 R424 W166 S106Y D507 R543 D515 W199 W155 W160 W161 W084 W085 C507 D518 W063 R501 W090 R426 C209 L603 C531 W202 C436 D602 D603 D604 W011 D607 W060 C624 W050 C766 C767 C768 D406 C439 D401 C403_1 D514 B505 B502 C535_1 T501 W112 C769 W164 C408 C527 R436 Q402 W088 W059 X601 C619 C630 CF202 D750 W139 W130 W138 W206 W061 W087 W086 W082 W083 W168 W162 W183 W165 C409 R517 D410 D402 C406 W809 W080 W081 W079 C1007 C1011 C1009 C1006 C522 C426 W173 W171 W170 R432 C415 C715 FB401 C761 C756 R502 C516 R404 W188 IC201 C211 C616 L204 R505 R509 C528 05 D5 W103 C529 C608 L205 C213 C604 C214 W021 C530 R442 R500 D527 D501 C502 D529 D504 R554 C517_1 D509 TH501_1 C541 R131 R128 W149 RY501 L101 CD501 C505 CP501 C519 D508 R553 D516 D528 L501 C533 C539 W833 R125 D601 C513 R515 D519 W110 W817 D103 R142 W805 C935 R908 D107 R107 D111 C117 W822 R139 L901 R907 W832 W026 C929 C303 C329 C919 C917 C921 D510 C118 W801 C924 C925 09 W0 D101 W100 R519 R001_1 W102 W098 W099 W194 D517 W101 W096 C504 W010 W033 W035 W034 W032 W036 W037 W136 C741 W185 W038 W039 W040 W151 W013 W148 W004 W005 W137 W142 W001 W041 W008 W042 L301 W018 W144 W017 W016 W055 W022 C729 W143 W023 W025 W024 D531 B504 D503 D530 W015 L601 C612 C216 W146 R735 W147 Q504 4 C203 W077 R527 D520 C123 R137 W002 W020 C704 C328 C724 FH501 C725 SW105 SW104 D407 C416 C420_1 C421_1 C423_1 R708 C705 L703 C711 R717 R741 R749 R748 W056 D711 R734 C751 R702 R723 R711 R770 R728 R707 W074 R705 W073 D001 TU001 C004 W069 C754 C755 C204 L602 C542 R443 W118 C430 C424 C427 W208 C003 W076 W075 W078 CP751 W197 D521 CP504 R506 D506 F501 FH502 SW103 SW102 SW101 D108 W834 C523 RISK OF FIRE - REPLACE AS MARKED. D109 OS101 J705 W028 CD702 CP702B J706 J707 W031 C506 W209 W111 Q501 W027 C326 S106X C501 R508 Q512 R535 R512 W029 R536 R537 R720 W211 W107 CP503 R520 Q507 C521 D513 W210 IC103 W169 S107X C111 W019 W195 D102 W012 W014 IC303 W030 D110 L302 D512 C508 W126 R624 CP502 IC101 W811 Q511 R141 W006 R534 R635 X101 C918 C122 W003 VR502 W831 C640 CP702A D606 C520 D502 IC504 C536_1 R521 W187 Q510 W186 W051 D614 R522 W106 R605 D611 D613 W128 C532 CD701B W125 D612 D608 R608 C615 D201 R503 W105 C510 Q508 IC502 IC503 W108 HS502 W044 W193 W097 W191 W047 D615 W299 W046 W045 W122 R542 W113 D511 W827 W133 W207 W117 C53 W091 W134 IC501 W807 R406 R430 C518 S103Y CF201 R621 W043 W192 W141 CF203 W092 W839 L202 W093 D106 TP005 W116 _1 38 R4 W114 W135 W049 S107Y W132 W048 L604 D605 W131 W062 C425_1 CP752 5 T401 W052 W182 C402 C625 W823 L203 R416 HS1001 R418 W177 R422 CP1001 R420 HS501 R221 W844 W159 W198 W204 W184 W83 HS402 W200 W181 W115 R407 D404 W179 W094 R152 W180 W145 IC1001 W158 C1003 W196 S105Y L751 W067 W071 W066 CF204 W095 CP1501 W058 W175 W152 L750 W140 W157 W065 W064 S104Y Q405 S103X W072 R439 CP401_1 C413_1 C411 IC401 W153 S102X S101Y C713 C735 W172 D411 S105X TP001 IC701 W804 W123 R441 R437 TP901 S101X CP101 C002 W068 J203 J704 J703 J701 C418 J702 CD801 CP801A S102Y C503 PRINTED CIRCUIT BOARDS MAIN/VIDEO JACK (INSERTED PARTS) SOLDER SIDE 0 R713 C720 C730 R756 IC751 R601 C613 C602 C759 R755 R006 R007 Q201 C762 C760 R211 C922 R118 R144 C201 R762 R761 Q750 Q751 R213 R217 C1002 R1004 C1010 R1011 C1001 R1010 C1012 R1003 R763 C753 C227 R223 R205 R210 R204 R203 R905 R904 Q204 C930 C932 IC902 C772 C773 C774 C633 C210 R212 R747 C202 R202 R327 C218 R768 R767 C620 C208 C606 R207 R750 C627 R140 C339 C931 C335 R325 C338 C928 C337 C336 R326 R328 C332 R619 R604 R607 C333 C605 C330 R614 R613 R612 R611 R610 R609 C618 C629 C601 C222 C634 R209 C215 C206 C212 R320 R323 C331 R758 C220 Q406 C637 R602 C607 C334 R736 R737 R730 C740 R739 R738 Q705 R138 C737 C707 C739 C738 C609 C614 R603 R111 C742 R732 R731 R727 R757 R759 C708 R616 C325 R319 R321 R322 R314 R133 C139 R101 R126 Q509 R760 C731 C763 Q107 C001 R1009 Q603 C617 C638 C639 R632 Q604 C632 C631 C623 C622 C621 R615 R769 R623 R150 C132 R716 Q753 Q754 C626 R638 R617 R110 R124 R119 C125 R532 R324 R003 C750 R123 R122 R154 C103 C105 R132 R129 R151 R130 C101 R109 R108 R121 C752 R714 Q752 R618 R636 C109 C113 C114 C108 R136 C107 R114 R115 R103 C128 R106 C121 R113 R112 C554 R510 C712 C728 C748 R715 C524 C721 R721 Q103 R740 C723 R722 R146 C124 R102 R134 Q101 Q102 C727 C793 R764 Q109 C745 C747 C722 R719 R701 R524 R525 R127 C726 Q709 C734 C746 R724 C744 C706 R147 C526 R511 R116 R726 R415 R419 R435 C438 R403 R533 IC198 R751 R412 R417 C509 R104 C743 R725 R752 C405 C512 PRINTED CIRCUIT BOARDS MAIN/VIDEO JACK (CHIP MOUNTED PARTS) SOLDER SIDE C120 Q704 C926 C112 C138 C927 R906 Q202 Q203 R214 R215 R201 C229 R220 R218 R219 C221 Q1001 R1013 Q701 Q755 C008 PRINTED CIRCUIT BOARDS CRT COMB SOLDER SIDE TP805 R806 R1510 Q1504 R1517 R1516 L1503 L1502 W802 R829 D808 W807 R1509 C1521 C1520 IC1501 C813 D807 R1511 R1512 Q802 L803 W002 W805 C1510 R1508 R814 C1506 CP1501 D802 C1512 R1518 C1509 C1528 C1507 Q811 R812 D809 SOLDER SIDE C1508 R809 (CHIP MOUNTED PARTS) SOLDER SIDE L1501 R819 C805 C815 (INSERTED PARTS) Q1502 Q1503 C1517 C8 08 W003 C1525 C1501 Q1501 C1531 P-IN-P CP805_1 R830 W001 (INSERTED PARTS) (CHIP MOUNTED PARTS) SOLDER SIDE SOLDER SIDE C820 L753 R804 C1837 W807 L1805 R808 W806 C1820 W810 W004 CP803 C1835 R1821 C1838 W001 L1804 W007 X1801 R1801 R1806 C1802 C1812 C1801 C1813 R1808 CP001 W003 IC1802 C064 CP051 C1828 Q1808 R1816 IC051 C1822 C1815 R1823 R1822 R1817 C060 R1831 R055 C1806 R1828 C1805 R1827 W886 R1814 IC1803 C1817 R1813 R1826 C1816 Q1803 C1821 C1814 Q1804 R1825 W808 D1801 R1803 R1805 W008 C1809 C1810 C1824 IC1801 R1810 C1825 R1819 C1827 C1836 R1809 R1812 C1819 C1818 C1826 C1807 C1829 L1802 C1804 C1823 L1801 R1815 TP806 W002 TP804 W005 D801 C779 R803 Q801 R815 R810 Q812 L802 L804 R813 R817 C804 CP806 Q810 Q803 R811 C823 R801 W804 R828 C809 D803 R821 C806 W004 C1513 R1501 C1526 C1522 C1514 C1515 C1505 R1503 R1504 C1503 C1504 L1506 C1519 W801 C1516 R1506 C1511 CP804 W803 R802 R1502 R1505 R1513 Q1805 R1829 R1832 R1830 R1833 Q1806 Q1807 A B C D E F G H MICON / TUNER SCHEMATIC DIAGRAM 8 8 (MAIN PCB) 0.01 B C002 3 4 5 I2C OFF VIDEO OUT 6 2 I2C SDA SDA SCL L002 100uH 2.7K 1/4W R001_1 AGC TP001 50V 2.2 KA FROM/TO CHROMA/IF AGC SCL NC 0 10 AFT 0 11 X RAY PIP_SD 0 NC PIP_AGC_ADJ TV MUTE BBE H IIC OFF C103 47K 1/4W R119 0 0 NC 4.9 0 NC 5.0 H_TONE_H FROM/TO DEFLECTION D107 POWER 1SS133 15.9 0 R142 10K 1/4W 0 X-RAY TEST Q103 KRC102RTK R125 45 KEY 2 EXT MUTE OSD_BLK 4.7K 1/4W X-RAY_TEST 10P CH 0 6 4.7K R141 FROM/TO AV SCL SDA EXT_MUTE 47K R124 47K NC TV_MUTE R138 SDA SCL FROM/TO POWER 40 H TONE OUT GND_POWER R107 0 10K C108 39 38 4.8 0 0 NC 0 0 D110 D111 MTZJ6.8B MTZJ6.8B 37 36 HLF 35 1.7 0 34 AVCC SDA2 (PIP) 5.0 33 NC 5.0 SDA1 0 4 100P CH AT+40V R108 32 14 NC SCL2 (PIP) 5.0 31 0 SCL1 P.CON+5V AT+5V 2.2K DEGAUSS_H C109 3 100P CH R109 P.CON+9V 4 2.2K 10K R102 50V 1 KA 0 17 10K R113 18 R112 P FAIL 19 P.FAIL 15 4.8 NC 16 0 NC X-RAY C122 NC POWER R110 1.5K 1/4W 0.01 B MTZJ5.1B C107 D101 0 13 R146 4.7K 2 POWER 1K C121 SPOT KILLER DEGAUSS H RESET IC103 PST600C 1.7 20 R106 RVCO 3.5 21 200P CH 3 5 FROM/TO SOUND 1K PIP_AV2 VHOLD LED 15K C128 PIPAV2 3 W834 VCC 1 1M 2 VCC 5.0 7 8 0 3 E1 E2 VSS 4 E0 W822 6.3V 2200 YK 0 2 0 1 10K 1SS133 5.0 C117 50V 0.47 KA 2 10K VSS 27 26 0 6 0 5.0 D103 50V1 KA 5 82P CH 5.0 3 0 R133 C111 3.3 1 5.0 MEMORY IC198 S-24C16AFJA-TB-0 OSC1 C101 0.01 B VCC X.OUT 28 25 3 1.9 X101 EFOEC8004T4 C118 2 C114 82P CH C113 MODE 3.2 SCL OSC2 2 X.IN RESET SDA 2.3 CNVSS 5.0 2.7uH 0 GND V.OUT R134 PIPAV1 5.0 1 R103 CVIN L101 0.1 B CV_IN 30 1K 2.8 29 C124 23 R147 22 0.001 B 24 FROM/TO AV AGC 1 I2C SCL TKC-M06X-A1 GND 13 TEST POINT CP101 4.6 1.3 NC 6.2 NC R007 270 5.0 270 5.0 6.3V 470 YK R006 5.0 NC 12 2 NC 1 AGC 3 ADRES 4 SCL 5 SDA 6 V.S 7 BPL 9 BTL 0 NC D001 MTZJ33A 0 NC 0.01 B 30.0 C001 OSD_BLK IF C125 0 44 KEY 1 12 2.5 PIP_AFT PIP_SD PIP_AV1 FROM/TO POWER 7 4.7K 1/4W R140 4.7K W805 1SS133 43 0 2.2K R136 SW103 SKHVBED010 VOL UP SW101 SKHVBED010 CH UP SW105 SKHVBED010 POWER 5.0 2.2K R116 560 SW104 SKHVBED010 56P CH C105 150P CH 10K 0 42 R114 AFC VOL DOWN 0.022 M C004 51 50 52 R154 X-RAY TEST 4.7K R121 41 560 SW102 SKHVBED010 10 NC 11 IF SYNC 7 2.7K 5.0 R104 CH DOWN 1.3 C008 0.3 8 R101 270P CH C120 NC OSD BLK 49 1 2 3 4 REMOCON R123 4.7K R122 D102 48 0 9 R126 OSD_G R139 10K R151 V.OUT1 4 4.9 OSD B 0 47 R118 SYNC SEP. Q109 2SC2412K 0 4.7K FROM/TO DEFLECTION FROM/TO VIDEO SWITCH 10K OSD G 0 4.7K AFT_OUT X-RAY 47K PIP_AFT OSD R 0 46 0 4.7K R144 V SYNC 5 820P CH C132 SYNC_OUT 5 0.3 R115 MICON OEC7062A H SYNC 6 4.8 R150 OSD_R SDA IC101 0 SPOT_KILLER W824 W818 0 4.8 FROM/TO CHROMA/IF 330K FROM/TO VIDEO SWITCH OSD_B 820 R130 33K R132 R131 4.8 0 10K 1/4W 0.01 B R129 3.9K H-BUFFER Q102 2SC2412K R003 C003 0.0022 B C112 MTZJ5.6B R137 68 1/4W D108 6 0 V-BUFFER 0 Q101 2SC2412K D109 SLR-342VCT32 R128 33K 1/4W 1K R127 4.8 RED LED POWER ON ENV56D66G3 14 3 GND 47 R111 BT002 R03(AB)E_20_T C138 TM101 7 2 B+ 4.9 C123 5.0 BT001 R03(AB)E_20_T 16V10 KA 0 1 Vout 15 TU001 8 OS101 PIC-28143SY-2 ACCESORY 0 W833 C139 0.01 B PCB010 TMA509 CAUTION: DIGITAL TRANSISTOR 1 NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. A B NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE C CAUTION: SINCE THESE PARTS MARKED BY CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY D ATTENTION: LES PIECES REPAREES PAR UN ETANT DANGEREUSES AN POINT DE VUE SECURITE N’UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES ARE E F 1 G H A B C D E F CHROMA / IF SCHEMATIC DIAGRAM G H (MAIN PCB) 8 8 FROM/TO AV 10K 1/4W 470 R605 R604 L601 47uH C640 16V1000 YK 75 75 R750 41 1.5 0 39 38 6.0 37 4.9 9.0 36 1 B 16V47 YK C617 2.2K R607 150K C616 100P CH C609 0.022 B R603 3.3K C612 50V2.2 KA 40 C638 0.47 B R632 1K R602 180K 2.7 35 7.1 34 4.0 33 2.1 0 32 31 6.0 30 3.4 NC 29 OSD_BLK SPOT_KILLER 1SS133 2.0 EW OUT 2.5 H_TONE_H 1SS133 DIG VDD 42 0.01 B 0.01 B C608 50V1 KA C633 C614 2.5 FBP IN/GP OUT 43 X-RAY 2.5 SYNC OUT 44 7 D601 270 1/4W H OUT 2.4 SCL D607 6 CHROMA IC201 TB1253N H AFC FILTER 45 R608 H VCC(9V) NC 1.9 V RAMP 46 V OUT 2.5 DIG GND 47 0.1 B 0.1 B C606 R601 2.4 C607 C604 50V 1 KA C605 48 C615 10V100 YK 8 CVBS OUT 3.6 BLACK DET FILTER 49 C IN 2.8 0.1 B C634 0.22 B C601 16V10 KA 50 V IN 3.7 U IN 51 CVBS EXT IN 2.4 52 APL DET FILTER 9.0 CVBS LNT IN 53 EXT AUDIO IN 2.4 MTZJ12B D201 C215 16V10 KA C214 54 DC NF FILTER CF203 TPSRA4M50C00-A0 6 4.1 DE-EMPH IF GND 2.2K 55 LOOP FILTER 3.3K R212 68 0 56 V REF 6 R204 100P CH C229 100 3.5 R210 15uH 470 0 3.1 R213 2.4 0.1 B IF DET OUT TV BUFFER Q203 2SA1037AK L204 C212 R205 TV BUFFER 9.0 Q202 4.1 2SC2412K 33P CH C216 470 C211 50V0.22 KA 10V100 YK NC R211 4 SYNC_OUT 10 SDA C213 1.2K R203 NC 3 220 2 CD701B CH243001 150P CH FROM/TO AV 220 C227 R223 7 1 3.1 C210 3.7 AUDIO BUFFER Q201 2SC2412K FROM/TO MICON/TUNER 11 9 1 B 9.0 TUNER_AUDIO_L TUNER_AUDIO_R 7 Y CLAMP FILTER 270 0.0022 B R215 FSC_OUT C613 R747 R214 IF VCC(9V) 5 L205 Y.OUT TUNER_VIDEO 47uH C.OUT FROM/TO VIDEO SWITCH PIP_OSD_B PIP_OSD_G PIP_OSD_R 10 2.0 11 12 2.9 13 1.6 20 0.1 21 2.2 22 2.2 23 2.2 24 9.0 25 5.0 5.0 26 ABCL IN IK IN EHT IN SDA SCL RGB VCC(9V) EXT B IN EXT G IN EXT R IN YC GND SVM OUT YS/YM IN 19 1.1 27 9.0 28 FROM/TO POWER 6.0 C626 0.012 B 50V 4.7 NA C625 39P CH 100 39P CH C632 100 R617 47uH 0305 R616 10V100 YK C631 C623 0.01 B C624 0.1 B L603 0.1 B C622 2.2K R615 C620 0.1 B C621 10K R623 2.7K R618 220K 11E1-EIC 0.1 B 4 D605 C602 1.5K 14 FROM/TO DEFLECTION H.OUT C221 ABCL 0.01 B B.OUT G.OUT 1 2 3 4 5 IN IN G OUTOUT CF202 SAF45MFG220Z 1SS133 1SS133 D615 1SS133 D612 D608 1SS133 1SS133 D614 68 3 R.OUT 1SS133 D613 220 1/4W 1.2uH 15 D611 R221 L203 470 R219 2.2 V.OUT2 0.1 B 0.6 R220 R218 CF204 MKT47.3MC110P-TF 18 0 C220 PRE AMP Q204 KTC3881S-RTK 1.3 17 4.8 W839 W823 W844 IF 2.2K 3 6.8K R217 6.2 AGC MTZJ6.2B D603 D604 R207 13 AFT_OUT 16 AT+12V P.CON+9V FROM/TO MICON/TUNER 4.8 5 12 GND_POWER P.CON+5V 15 4.8 B OUT G OUT R OUT 14 5.0 MTZJ6.2B 1.2uH YC VCC(5V) CW OUT APC FILTER X’TAL(3.58MHz) 2.1 C627 100uH L202 9 MTZJ6.2B D602 3.2 33K 50V0.22 KA C618 0.01 B L604 8 X601 0.01 B C637 8P CH 3.579545MHz C629 3P CH R619 C630 0.0022 B 2.7 R209 7 RF AGC IF AGC IF IN 0.1 50V0.47 KA C206 6 33K C222 0 0.01 B C209 IF IN 5 0 0.01 B C208 4 NC 0.1 B C218 0 AFT OUT AUDIO OUT VCO ADJ FILTER 3 16V10 KA IF VCC(5V) C203 C202 1K 5.0 0.01 B L602 R202 2 3.0 C619 47uH 0305 R609 6.3V 470 YK R610 100 R611 2.7K R612 100 R613 2.7K R614 100 4 C201 FROM/TO POWER 0.01 B CF201 EFCT4R5YS5A 1 16V100 YK C204 1K R201 5 SIF/H CORR IN PIP_SW R621 AFC R624 C935 V.BLK Q604 0 2SC2412K 2.2 2.2 50V2.2 KA C921 dbx De-Emph 7 0.4 Vcc Expand Spectral 8 9 5.1 2.4 B C D 16V10 KA C922 C918 220K C917 R906 WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. 2.6 3.7 13 0 4.8 SPOT KILLER Q603 0 2SC2412K Filter SAP Demod SAP RMS Det Spectral Det Noise 11 0.4 2 Det SAP Filter Spectral 2.4 V.OUT1 33K 1/4W 0.1 B C931 0.1 B Filter Noise 10 E 14 VCA Input C930 0 NC 2.3 NC2.3 50V4.7 KA C919 6 Filter Stereo Filter Wide Band 3.6 Det Pilot 12 2.3 3.4 0.1 B L+R Demod RMS Det Wide Band 15 R635 2.0 L901 22uH 10V100YK L-R Demod L+R Filter 5 0.047 B C928 Cancel Pilot L-R Filter 50V4.7 KA 4 3.7 St.PLL fH.2fH Trap Filter 2.3 3 C926 ZAP IIC Decoder Switch De-Emph (L-R)/SAP 75us Filter Cancel SAPout Offset Expand Cancel Wide Band Offset 2 16 GND DAC Matrix 1 100 1/4W NC 0 5.0 5.0 0 20 19 18 17 0.1 B C932 OUT SW 2.3 R907 470 21 C924 2.3 50V3.3 KA 22 0.022 B C929 2.3 50V0.33 KA C927 23 NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR. THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP IS NON POLAR ONE. A NC AGC NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE 1 2.3 0.022 B C925 SOUND DECORDER IC IC902 AN5829S 24 100 1/4W R908 NC 2 470 R904 R905 AUDIO_L TP901 120 1/2W 2.2K 50V4.7 KA 120 1/2W R636 3.6 F R638 1K TUNER AUDIO SIGNAL TUNER VIDEO SIGNAL LUMINANCE SIGNAL COLOR SIGNAL DEFLECTION SIGNAL R.SIGNAL G.SIGNAL B.SIGNAL G PCB010 TMA509 H 1 A B C D E F G H DEFLECTION SCHEMATIC DIAGRAM 8 8 (MAIN PCB) V.OUTPUT IC401 LA78041 6 7 12.0 25.0 17 C436 7 18 C414 100V0.068 MKT 680 1/2W 680 1/2W R429 R425 680 1/2W R421 D403 D410 V801 A68AJB82X10 680 1/2W C409 50V10 YK VR401 R409 2.2K METAL 220 1/2W V.POSI R424 R408 2.2K 1/2W C408 R420 R415 C406 W827 R152 2.2 1/2W 0 P.CON+5V R416 HS402 763WAA0216 50V1 YK 820 0 5.6 1/2W S107X S107Y FROM/TO POWER 12K +-1% C405 SWITCH Q107 KRC111RTK 4.8 560P CH R413 6 25V2200 MHE 500V10P SL 27K +-1% R417 33K MTZJ30B MTZJ30B C411 R414 C417 100V 0.22 MKT D402 11E1-EIC C407 3.9K 1/4W 4.0 35V100 YK R407 R442 5 16 R437 1 1/2W 7 2.2K 1/4W PUMP UP VCC GND 1 2 3 4 4.0 25.0 2.0 0 8.2K + THERMAL PROTECTION AMP 16V 47 YK R412 - 9 10 8 6 11 FROM/TO DY CP401_1 TS-80P-04-V1 P.CON+9V 6 R G B 5 7 1 4 3 1K 1/4W +B R439 21 330 R406 2 YR FB401 2.8 +B TP002 2KV 470P C423_1 1 5 4 3 MPP C420_1 0 2KV470P YR 0 200V 0.47 FHS H.OUT Q405 2SD2499(LBOEC1) 2.8 20 0.1 C431 H.DRIVE Q402 2SC2621 C403_1 0.4 50V 1 YK C402 17.3 4.7K 1/2W 500V0.0022 B T401 ZTS7196-3 100 1/4W 19 POWER 500V 0.001 B R428 5 13.1 W807 108.0 105.0 0 0 R404 4 500V330P B FROM/TO VIDEO SWITCH D405 R432 AFC MTZJ9.1B D404 AU02A-EIC 8.2K 1/2W 1 2 9 10 C419 2 1 CD803 SM1098-009-1A 2 CD805 SM1098-009-1A C425_1 5 ANORD HV E180 B+ AFC HEA TER F GND S FORCUS FROM/TO CRT SCREEN 4 GND 0 11 ABL 0 GND 8 NC E8 0.1 5 NC 500V 0.001 B 1 3227008R COL 6 TO CRT 1 ELH5L4113 2KV0.001 YR 8 E12 0.2 4 NC E27 2.0 3 C415 180 1/2W V.OUT1 1K 1W C418 1.25KV 0.015 C421_1 AT+40V R403 2 L402 1SS133 D106 GND_POWER 7 8.1 R443 68K 1/2W C427 100V 0.1 MKT 18K +-1% 1K R435 2.2K V.OUT2 H.OUT ABCL AU02A-EIC B.OUT R.OUT G.OUT 2 TP004 TP005 D407 AU02A-EIC 250V 22 MHE R441 5.6K +-1% C426 R436 8.2K +-1% FROM/TO CRT 35V1000 YK R418 18K +-1% R426 R419 MTZJ11B 500V 0.001 B D411 C430 AFC V.OUT1 C424 15.9 C413_1 10.9 0.001 B D406 3 0.22 1W C439 FROM/TO CHROMA/IF X-RAY TEST Q406 DTA144EKA 100K 1/4W 15.9 +-1% MTZJ27B R438_1 R422 X-RAY 500V470P B 0.001 B D401 68K 1/2W C438 R430 3 100V22 YK X-RAY_TEST V.OUT1 AFC C416 FROM/TO MICON/TUNER CP801A(CP805) B2013H02-10P 180V NC NC PCB010 TMA509 CD801 CU2A3401 1 NC 2 NC 3 GND 4 HEATER 5 B.OUT 6 R.OUT 7 G.OUT 8 P.CON+9V 9 GND 10 DEFLECTION SIGNAL R.SIGNAL G.SIGNAL B.SIGNAL CAUTION: DIGITAL TRANSISTOR 2 CAUTION: DIGITAL TRANSISTOR 1 1 NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. A NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE B C CAUTION: SINCE THESE PARTS MARKED BY CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY D ARE ATTENTION: LES PIECES REPAREES PAR UN ETANT DANGEREUSES AN POINT DE VUE SECURITE N’UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES E NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR. THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP IS NON POLAR ONE. F G H A B C D F G H POWER SCHEMATIC DIAGRAM 6.3A 125V 8 E CAUTION: FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH THE SAME TYPE FUSE 6.3A 125V(F501) (MAIN PCB) ATTENTION: POUR UNE PROTECTION CONTINUE LES RISQUES D’INCEIE N’UTILISER QUE DES FUSIBLE DE MEME TYPE 6.3A 125V(F501) D516 7 8 1SS133 10.9 RELAY DRIVE Q504 KTC3198 7 R515 0 10K 1/4W 0 50V 470 YK C542 10 1/2W 10K1/4W R535 10K C504 R525 C523 8.9 9.5 8.7 R522 27 2W AT+5V 4 P.FAIL 1K 1/4W C533 5.0 MTZJ5.6B R512 3 16V10 KA D513 OUT C532 W811 9.5 GND 2 +5V SW 1 8.7 0 Q510 2SD734 8.9 8.7 DEGAUSS_H AT+40V P.CON+9V P.CON+5V HS502 763WAA0200 GND_POWER POWER 3 C520 B +12V SW Q508 KTA1273_Y 12.1 SB290S 11.3 FROM/TO VIDEO SWITCH 22K 0.1 IN 1 GND OUT 2 3 11.3 GND_POWER 9.0 P.CON+5V P.CON+9V 5.0 C528 27 2W 16V1000 YK STAND BY SW. 0 Q509 KRC102RTK IS THE LIVE CONNECTION 0 R521 1SS133 R519 C527 11.9 C530 R511 1SS133 D517 REG.+9V IC502 KIA7809API 10V470 YK D519 500V 0.0022 D512 CAUTION: 4.9 X-RAY 6.3V 1000 YK C534 R502 250V 0.0033 KH C522 1SS133 100K 1/2W D508 D528 R509 R510 MTZJ5.6B R554 27K 1/2W VR502 10K R508 2.7K 1/4W +B ADJ IN GND1 220 8.9 REG.+5V IC503 KIA7805API +5V SW Q511 KTC3203_Y R534 35V100 MHE D521 1SS133 P.CON+5V GND_POWER 0 16 132.4 NC 1 0.15 1W 1SS133 R506 2.2K 1/4W R542 C524 0.001 B D518 R543 680 1/4W 1N4937 R532 1K 2KV 0.0012 YR C535_1 2KV0.0022 YR D515 9.7 2 D506 C510 0.001 B P.CON+9V 2.2K 5.6 AT+5V REG. Q501 KTC3203_Y C512 C509 1SS133 0.0056 B B502 W4BRH3.5X6X1.0X2 1.5 11EQS04N 3.3K 1/4W R503 1 100 R533 R553 9.7 6.3 FEED BACK SWITCHING Q507 5.7 KTC3198 27K 1/2W W817 3 16.3 10.7 FEED BACK IC504 TLP621(D4-GR-LF2) C554 0.0022 B 3 R524 FROM/TO MICON/TUNER C518 500V 0.0022 B 26.0 15 D507 4 SB290S 2KV 0.0022 YR 20.0 14 P2 16V470 YK 3 390 1/4W C529 138.9 C536_1 13 R520 B505 BL02RN2-R62T4 PT 1N4937 D514 0 C531 16V470 YK 125.0 NC 4 5 FROM/TO AV D511 50V1 KA 5 240.0 12 160V100 YXF 11 AT+40V P.CON+9V +B P.CON+5V GND_POWER C521 0 6 1 4 FROM/TO DEFLECTION 0.68 2W 30DF6-FC 1K 1/2W 47K 3W R505 CP504 005P-2100 CONT VCC GND S D 5 4 3 2 1 4.0 17.6 0 0.1 138.9 FB/ OCP 1 R527 160V100 YXF 10 40.0 6.3A 125V B504 P1 0 CP503 005P-2100 W5RH3.5X5X1.0 7 C526 SW REG. IC501 STR-G6624 25.0 141.6 DRIVER 2 C501 200V470 UP C507 1N4005-EIC 9 HS501 763WAA0181 P.CON+5V GND_POWER C539 D510 8140064S 390 1/4W C508 T501 6.3A125V FH501 FH502 EYF-52BC EYF-52BC 51MS 6.3A L CC SOUND_GND 56K1/4W 47K1/4W 50.0 BLACK 6 P.CON+9V 100V 2.2 MHE R536 2KV0.0022 YR 1 1 BLACK 1 2W C517_1 F501 5 SOUND+B 35V1000 YK 1N4005-EIC D502 1N4005-EIC D530 1N4005-EIC D503 1N4005-EIC D531 2 1N4005-EIC 1 D504 4 C502 CURRENT DET. Q512 2SA1624 16V2200 YK WHITE 21DQ09N-FC4 0.001 B WHITE 3 C503 2KV0.001 B AT+12V FROM/TO SOUND R517 R537 2KV0.001 B 1N4005-EIC D529 C505 CP501 A3963WV2-3PD 275V0.1 PHE840 ZPB45BL3R0A 2 2 BLADE WIDE TH501_1 120V 60Hz CD501 250V 470P KH D501 L501 SS28H-20075 275V0.1 PHE840 2 C506 1 1 500V 0.0022 B P.CON+5V GND_POWER D505 R501 1.2 7W 1N4005-EIC D527 4 CP502 TV-50P-02-A1 2 6 3 R500 DEGAUSS COIL L503 8R270008 1 C541 C516 500V 100PB P.CON+9V W801 10ELS6N 2.7M 1/2W +-10% 2 C519 RY501 ALKS321 250V 470P KH C513 250V 470P KH FROM/TO CHROMA/IF D509 2 PIP_PCON+8V D520 1SS133 CAUTION: DIGITAL TRANSISTOR 1 NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. A NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE B C CAUTION: SINCE THESE PARTS MARKED BY CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY D ARE ATTENTION: LES PIECES REPAREES PAR UN ETANT DANGEREUSES AN POINT DE VUE SECURITE N’UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES E 1 NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR. THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP IS NON POLAR ONE. F PCB010 TMA509 G H A B C D E F G H SOUND SCHEMATIC DIAGRAM 8 8 R324 100P CH C336 1.5K C326 100P CH C337 2.7K C328 R314 23 C334 7 1.8K 0.033 B C332 C331 0.47 B R326 W832 AUDIO_L 7 22 50V2.2 KA AUDIO_R 16V47 YK R322 FROM/TO AV 4.7K R321 (MAIN PCB) 100 R328 0.022 B 100 C329 5.0 5.0 4.8 C330 C333 6.5K 9 10 I2C BUS INTERFACE 6.5K CONTROL LOGIC + TONE VR6 AMP2 15 14 13 6 4.7 4.8 0 12 11 5.0 4.9 C339 0.1 B C335 C303 1.8K 0.033 B 16V47 YK 100K C338 R327 1.5K R323 0.1 B L301 47uH 5 0.001 B 4.7K R325 5 C325 7 8 TONE AMP1 + - 4.7 0.022 B 0.47 B 2.7K L302 6 VR5 4.8 S8 S2 5.0 0 4.8 5 VR3 SIMAMP1 VOLAMP16.5K VOLAMP2 SIMAMP26.5K VR2 + 136K 1.8K VR4 20 19 18 17 16 R320 22uH 4.7 + + - REF REF 10.0 R319 4 1.8K + - VR1 4.8 S7 3 136K REF 50V2.2 KA 6 2 5.0 S3 S5 TONE CONTROL IC303 M62420SP 1 5.0 S1 5.0 S4 S6 5.0 W831 FROM/TO MICON/TUNER SCL SDA 4 4 TV_MUTE SOUND AMP IC1001 AN5276 + - + ATT. R1003 C1001 330 R1004 1B C1002 C1003 1B 35V 1000 YK 330 25V1000 YK R1010 10K R1011 10K W835 STAND CH1 VCC -BY OUT 10 11 12 14.9 12.1 6.7 0 C1004 C1010 C1012 R1013 25 3 0.068 B SOUND_GND 25V1000 YK GND_POWER CH2 NC MUTE GND OUT 6 7 8 9 0.7 0 6.7 C1009 C1011 SOUND+B 3 0 0.068 B P.CON+9V 35V100 YK CH1 NC IN 1 2 0 NC P.CON+5V 24 ATT.CONT. + RIPPLE FILTER CH2 GND RF IN 3 4 5 0 13.9 0 10K + FROM/TO POWER W/CONECTOR.2SPEAKER 10K 3.6 W809 MUTE Q1001 KRC111RTK 26 0 HS1001 763WAA0215 C1007 SPEAKER CP1001 TID-X04P-Z1 8 OHM 2.5W 4 4 3 3 2 2 1 1 16V 22 KA C1008 NC 27 0 50V 2.2 KA 2 220P B C1006 R1009 (L) 2 SP1001 070Y435002 (R) 8 OHM 2.5W AUDIO SIGNAL CAUTION: DIGITAL TRANSISTOR 1 NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. A NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE B C CAUTION: SINCE THESE PARTS MARKED BY CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY D ARE ATTENTION: LES PIECES REPAREES PAR UN ETANT DANGEREUSES AN POINT DE VUE SECURITE N’UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES E NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR. THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP IS NON POLAR ONE. F G PCB010 TMA509 H 1 A B C D E F G H AV SCHEMATIC DIAGRAM 8 8 (MAIN PCB) FROM/TO CHROMA/IF YUV_IN(REAR) J704 AV3-19D-5 1 7 MONITOR V.OUT 5 Y IN 4 C IN 3 GND 2 FSC 1 P.CON+5V 4 5 H1 R708 6035B-06Z002-T 75 1/4W CP1501 A/V_OUT(REAR) J203 AV3-19DS-1 4 34 FROM/TO POWER 6 4 L703 1 E 3 75 1/4W 0.0056 B R741 R713 LINE1(REAR) J701 AV3-19DS-1 4 5.2 16V470 YK 68 BUFFER Q709 2SA1037AK 2 E H1 NC H1 H2 0 C715 0.0056 B C744 C743 8P CH 16V47 KANP C706 4.6 270 R726 3.3K C705 5 1K R724 1K 3.3K 16V10 KA 5 5 5 1 3 4 2 6 R707 75 1/4W 75 1/4W 75 1/4W FRONT.AUDIO.L FRONT.AUDIO.R 3 3 FRONT.AUDIO.R GND 4 4 GND P.CON+9V 5 5 P.CON+9V 5.4 3.9K E E 1 E R739 3 C742 C725 50V 1 KA 0.0056 B 220K 2.8 NC 2 2 2 FRONT-AUDIO.R J707 AV1-06DS-2 H FRONT.AUDIO.L 8.8 C740 FRONT.VIDEO 3 0.0056 B S_Y_VIDEO 1 220K FROM/TO VIDEO SWITCH CP702B B2013H02-5P 1 1K CP702A A2001WV2-5P FRONT.VIDEO R731 CD702 CU252002 1 2 3.9K 2 R732 H R737 220K 220K C724 50V 1 KA BUFFER Q705 2SC2412K R738 0 FRONT-AUDIO.L J706 AV1-06D-4 5.4 1K 15 ADRESS 2.8 R727 1 B 8.8 R730 R720 5.4 BUFFER Q704 2SC2412K R736 SDA 5.0 470 1 B C739 16 18 SCL R716 1 B C738 5.4 C793 220 17 50V3.3 KA C741 SDA 5.0 C737 C704 4.8 R719 R701 0.0056 B R702 0 100 1/4W 4.8 1 3.9K 1/4W FRONT-VIDEO J705 AV1-06D-3 PCB170 TEAA68 H 1 B 470 1/4W R734 5.4 R770 10K 1/4W 470 1/4W R748 33P CH 13 MUTE 3.9K 1/4W R717 1 B C746 R735 0 14 EXT_MUTE 19 4.7 20 0 1 B C722 4.8 33P CH 8 9 10 11 S2 1 B R749 C734 25 24 21 GND C745 5.4 4 S-JACK J702 YKF51-5503 1K C747 MTZJ6.2B 4.7 12 4.8 FROM/TO MICON/TUNER R705 0.1 B D711 7 26 BIAS 23 4.7 3 3.9K 1/4W C748 10V470 YK 4.0 22 AUDIO_R 470 R715 4.7 33 220 B 0 5.8 SCL 1 4.7 S1 16V 22 KA 4.8 32 CV_IN 1 B R728 C721 C735 AUDIO_L 3.9K 1/4W C750 R714 5 9.0 150P CH 1.5K Vcc B 6 0.01 B R722 28 C731 C723 C726 1 5.4 27 1.2K 2.5 50V0.47 KANP FROM/TO SOUND 31 3.1 R721 C729 9.0 1.2K Y.OUT R740 4 C733 16V100 YK 470 1/4W R711 2 4.8 2.5 BUFFER Q701 2SC2412K R723 1 B C712 1 C720 33P CH 5.4 30 C728 0.01 B 100uH 0607 C.OUT 5.4 3 5.2 B 4 0.1 L701 31 1B TUNER_VIDEO 4.7 30 C730 5.4 29 1 B 32 C708 C707 75 1/4W C753 FSC_OUT TUNER_AUDIO_L TUNER_AUDIO_R 0.0056 B C727 FROM/TO CHROMA/IF 6 AV SW IC701 MM1311AD E 3 5 1 R751 R725 R752 C711 C714 6 C713 16V10 KA GND_POWER 2 47uH 0305 E H1 NC H1 H2 P.CON+9V P.CON+5V 2 1 LINE2(REAR) J703 AV3-19DS-1 16V100 YK 6 5 6 E 3 2 E H1 NC H1 H2 6 E 29 FROM/TO COMB FILTER 7 H2 3 2 E H1 28 1 2 3 4 CD701A CH243001 2 S_C_VIDEO REAR_VIDEO2 PCB010 TMA509 REAR_VIDEO1 TUNER_VIDEO NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR. THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP IS NON POLAR ONE. 1 A B NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. C AUDIO SIGNAL TUNER AUDIO SIGNAL TUNER VIDEO SIGNAL COLOR SIGNAL LUMINANCE SIGNAL D E F G 1 H A B C D E F G H VIDEO SWITCH SCHEMATIC DIAGRAM 8 8 (MAIN PCB) IC750 PIP-VIDEO SW. BA7645N MUTE LOGIC 7 7 1 2.9 FROM/TO MICON/TUNER 2 5.0 3 5.0 4 5 2.6 0 6 2.6 7 8.9 8 9 2.6 0 10 1.6 L751 100uH OSD_B OSD_G C751 S_Y_VIDEO 0 1 B C763 1 B R763 16V100 YK C761 1K C762 1 B C759 1K R762 1K 4.1 BUFFER Q755 2SA1037AK 1.7 P.CON+9V 1 SCL 2 SDA 3 0.1 B 6 4 NC PIP P.CON+8V 5 GND 6 7 NC 8 PIP AFT 9 NC C752 R756 S_C_VIDEO TUNER_VIDEO R758 16V 10 KA 2.2K 4.1 BUFFER Q751 2SA1037AK CP752 (CP051) IMSA-9130B-09 C756 16V 10 KA 1.1 OSD_R FROM/TO AV 8.2K R757 R755 R761 FROM/TO P-IN-P/TUNER 16V10 KA 6 4.8 BUFFER Q750 2SC2412K 1.8K C754 PIP_AFT OSD_BLK 1K R760 C755 SDA 16V 100 YK SCL 2.2K R759 L750 100uH PIP_SD C760 PIP_AV2 1 B PIP_AV1 1.2K W804 CP751(CP001) IMSA-9130B-09 REAR_VIDEO2 REAR_VIDEO1 1 R764 5 FROM/TO POWER 22K P.CON+9V GND_POWER PIP VIDEO 2 HD 3 VD 4 RGB B 5 RGB G 6 RGB R 7 GND 8 PIP SW 9 5 P.CON+5V BUFFER Q752 2SC2412K 5.0 1.4 0.7 R767 4 4 1K C774 1 B 5.0 PIP_PCON+8V BUFFER 1.4 Q753 2SC2412K 0.7 R768 1K 5.0 BUFFER Q754 2SC2412K 1.4 C769 R769 0.7 6.3V 470 1K YK 3 3 ANALOG SWITCH IC751 MM1234 1 FROM/TO DEFLECTION V.OUT1 AFC 2 1.4 2 0 3 0.7 IN1B SW1 IN1A GND1 IN2B 16 1.4 15 OUT1 0 14 1.4 0 4 5 0.7 6 0.7 7 0.7 8 1.3 GND2 OUT2 OUT3 SW3 VCC SW2 GND3 IN3B 13 12 4.9 IN2A 0 11 1.4 10 IN3A 0 9 1.4 C772 FROM/TO CHROMA/IF 2 1 B 1 C768 C773 B 6.3V 47 KA C767 6.3V 47 KA PIP_SW C766 PIP_OSD_G 6.3V 47 KA D750 PIP_OSD_R 1SS133 PIP_OSD_B PCB010 TMA509 1 NOTE: THE DC VOLTAGE AT EACH PART WAS A 1 NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK B C TUNER VIDEO SIGNAL D E F G H A B C D E F PICTURE IN PICTURE SCHEMATIC DIAGRAM 8 G H (P-IN-P PCB) 8 7 7 L1804 10uH REG.+5V IC051 KIA7805API 0.01 B C1820 3 4 270P CH 10V100 YK C1822 10V 100 YK 0.01 B 3.2 R1812 3.0 390 38 37 36 VOUT/B_OUT 35 BGPM 2.0 3.0 TESTEN 34 5 0.01 B 6 0 NC ADJ_VSUB R1813 390 C1817 R1814 390 0 TEST6 SWMG RESET DVDD2 DVSS2 MCK CSYNCS HD 33 TEST5 VD 32 10 11 0 FSC 5.0 2.2 GREEN BUFFER Q1804 2SC2412K 3.0 R1827 1K 5 5.0 2.2 BLUE BUFFER 5.0 Q1805 2SC2412K 3.0 2.2 R1825 1K 0 12 3 2 1 0 0.1 NC 3.5 SCK 3.0 UOUT/G_OUT C1816 0.01 B 0 13 4 7 NC VOUT 0 NC 14 GND 2.0 ADJ_YSUB R1826 1K 0.01 B 0 15 CN BGPS 8 VIN DVSS1 9 7 NC DVDD1 RED BUFFER Q1803 2SC2412K 3.0 W806 0.7 0.4 SYNC SEP. Q1808 2SA1037AK 8.5 0 R1823 1.2K 680 0.2 0.8 0 W807 FILTER AVDD (VCXO) AVSS AVDD (ADC) 2 PIP VIDEO 3 HD 4 VD 5 RGB B 6 RGB G 7 RGB R 8 GND 9 PIP SW VRT VIN (ADC) 0.01 B 0.4 R1809 6.3V 47 KA X1801 10uH 0305 390 14.31818MHz 18P CH C1824 0.22 B C1825 0.033 B R1819 C1827 3.2 3 0.22 B 3.2 W810 C1818 0.6 0.01 B 1.1 C1819 0.1 B C1836 0.01 B C1826 12K 23 VIN (SYNC SEPA.) 1.9 1.3 22 20 VRB 21 0.01 B C1810 1.6 5.0 1K 33K R1833 0.1 0.7 R1832 3.9K R1830 R1829 R1828 NC 1 1K 0.2 CP001(CP751) IMSA-9130S-09L 22K FROM/TO VIDEO SWITCH H-BUFFER Q1807 2SC2412K 5.0 1K R1831 V-BUFFER Q1806 2SC2412K L1805 3.2 1.6 C1809 0.5 L753 100uH 0305 C1838 BAIS 0.01 B X’TAL (NTSC) 3.2 C1837 1K 1/4W 0 X’TAL (PAL-M) 29 10K 0.01 B 3.2 X’TAL (PAL-N) 4.7M 3.3 R1821 8.5 R1822 39K R1816 C1828 0.47 B R1817 470 470K C1829 R1815 3 0.0015 B W886 C1805 D1801 W808 C1807 16V 10 KA NC 10V100 1SS133 YK C1813 R1808 YK R1810 3.2 15K C1815 R1806 28 10V100 30 L1802 470uH 0607 4 0 27 C1804 AVSS (VCXO) 26 NC 25 0 NC 24 PIP AFT 31 NC 9 2 C1821 2.0 0.01 B C1835 42 41 40 YOUT/R_OUT SCLK 39 AVDD (DAC) 0 C1814 1 2 3 SDATA 19 8 ADJ_USUB 16 GND 7 5.0 470P CH 6 C1801 PIP P.CON+8V ACK 17 270P CH C604_1 5 CONT NC 5 0.1 NC 6 2.2 4 3.7 3.2 10V 100 YK C1802 SDA AVSS (SUB) 18 6.3V 1000 YK C060 SCL 3 2.1 10uH CP051(CP752) IMSA-9130S-09L P.CON+9V 0.7 NC 6 100 1/4W L1801 C779 M65664FP SVM 0.8 5.0 5.0 2 0.8 100 1/4W R1805 16V 47 YK 1 VCC R1803 5 FROM/TO VIDEO SWITCH P-In-P 4 5.0 0.8 C1812 0 0 3.3V REG IC1802 MM1563F 8.7 GND IC1801 5 3 C1823 OUT 2 0.1 B GND 1 C1806 IN R055 27 2W 4 1.5 100 1/4W 1 R1801 6 2 LEVEL SHIFT IC1803 TC7SET08F 6.3V 47 KA 2 PCB250 TEAA69 NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR. THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP IS NON POLAR ONE. 1 A B NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. C NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE D CAUTION: SINCE THESE PARTS MARKED BY CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY E ATTENTION: LES PIECES REPAREES PAR UN ETANT DANGEREUSES AN POINT DE VUE SECURITE N’UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES ARE F G 1 H A B C D E F G H CRT SCHEMATIC DIAGRAM 8 8 R804 FROM DEFLECTION L802 7 TP804 CP805_1(CP801A) A2001WV2-10P RED AMP Q801 2SC2621 7.8 10 GND 9 P.CON+9V 8 G.OUT 7 R.OUT 6 B.OUT 5 HEATER D801 4 GND 1SS133 3 NC NC 2 NC NC R813 R828 220 1/4W 123.5 7.3 121.0 582.0 R801 1SS133 R806 1SS133 0.0022 M D808 D809 0 0 8 9 1SS133 TP805 6.2 10 6 11 5 2.4 C804 1.8K 1/4W C813 D807 3.0 100 1/4W RED AMP Q810 2SC1740SP 12 R817 270 1/4W 180V 7.3 150uH 12K 2W R810 7 117.0 390P B 1 7 37 2.7K 1/4W L803 6 150uH 12K 2W (CRT PCB) 1 0 119.0 6 NC F J801_1 CVT3275-5102 38 R829 2.7K 1/4W R814 5 220 1/4W GREEN AMP Q802 2SC2621 7.8 123.9 5 7.3 D802 1SS133 7.3 2.5 3 NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. 1 A B NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE C D CAUTION: SINCE THESE PARTS MARKED BY CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY E 005P-2100 CP804 PCB110 TCA367 1 SCREEN GND GND CP803 TS-80P-02-V1 FOCUS 2 1 GND GND ARE 2 1 2 CP806 TS-80P-02-V1 FROM DEFLECTION 470P B C806 100 1/4W 1.8K 1/4W BLUE AMP Q812 2SC1740SP R821 270 1/4W R809 100 1/4W 330P B R830 D803 R811 C823 4 39 7.3 1SS133 R803 3.1 3 C808 2KV0.001 B 119.7 7.8 220 1/4W C809 250V2.2 YK W804 2.7K 1/4W BLUE AMP Q803 2SC2621 R815 150uH 12K 2W R808 TP806 L804 C820 4 500V 0.001 B C805 1.8K 1/4W 390P B C815 330P B 100 1/4W 3.0 R819 270 1/4W 7.3 GREEN AMP Q811 2.4 2SC1740SP R802 R812 R.SIGNAL G.SIGNAL B.SIGNAL 2 ATTENTION: LES PIECES REPAREES PAR UN ETANT DANGEREUSES AN POINT DE VUE SECURITE N’UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES F 1 G H A B C D E F G H DIGITAL COMB FILTER SCHEMATIC DIAGRAM 8 8 7 7 (COMB PCB) 6 47P CH 560 1K C1528 R1511 22uH DVSS 6.3V 470 YK C1520 DVDD 0.01 B 5.5 C1521 KILLER CKIN 100P CH 0 CP1501 6035B-06Z002-T MONITOR V.OUT 6 5 C IN 4 GND 3 FSC 2 P.CON+5V 1 47 R1508 3 BUFFER Q1502 2SA1037AK 2.8 W805 C1531 C1519 1K 0.01 B 0.1 B C1517 1.2K 16V100 YK 100 15uH 180 BUFFER Q1503 2SC2412K R1513 Y IN 1K 47P CH C1526 0.1 B R1504 2.4 2.1 3.3K R1503 C1503 100P CH R1509 R1505 L1502 W802 BUFFER 1.1 Q1501 C1505 2SC2412K 56P CH C1504 4.4 1.7 0.1 B 5.0 4.4 5.0 R1512 C1501 6.8K 10uH L1501 R1502 W807 3 4 FROM/TO AV 0.01 B C1522 180P CH 820 C1516 9 2.5 0.1 B VFIL R1506 C1514 8 100 R1501 10 2.2 C1515 0.01 B C1513 0.01 B C1510 0.01 B 0 7 11 3.6 C1506 4 0 6 12 4.2 L1506 0.01 B 2.6 BIAS3 13 1.4 5 TEST C1512 2.6 ADIN 14 3.8 4 C1525 50V3.3 YK 5 BIAS1 3.0 BIAS2 YOUT 15 5.4 3 VRT VRB AVSS 16 0.01 B 0.01 B C1509 2.4 2 COUT 0 AVDD DIGITAL COMB FILTER IC1501 TC90A45F C1507 W801 1 24K L1503 W803 R1517 1.9 KA 820uH 5 27K 2.5 1K 50V0.1 R1516 C1508 27P CH C1511 5.4 R1518 BUFFER Q1504 2SC2412K R1510 6 PCB330 TEAA70 2 A B RECORD COLOR SIGNAL RECORD LUMINANCE SIGNAL TUNER VIDEO SIGNAL NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE 1 WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL. C D 2 E 1 F G H WAVEFORMS MICON/TUNER 1 2.0V 50ns/div 6 500mV 10µs/div 11 500mV 50µs/div 2 2.0V 50ns/div 7 200mV 10µs/div 12 100mV 100ns/div 3 2.0V 50µs/div 8 1.0V 5ms/div 13 4 9 1.0V 20µs/div 14 1.0V 20µs/div 10 2.0V 20µs/div 15 1.0V 20µs/div 2.0V 50µs/div 1.0V 20µs/div CHROMA/IF 5 200mV 10µs/div NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram. WAVEFORMS DEFLECTION 16 1.0V 5ms/div 21 200V 20µs/div 26 500mV 1ms/div SOUND 17 10V 5ms/div 22 1.0V 2ms/div 27 500mV 1ms/div AV 18 10V 5ms/div 23 1.0V 2ms/div 28 200mV 20µs/div 19 50V 20µs/div 24 20mV 1ms/div 29 200mV 20µs/div 20 2.0V 20µs/div 25 20mV 1ms/div 30 100mV 10µs/div NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram. 31 500mV 10µs/div 38 50V 10µs/div 32 1.0V 1ms/div 39 50V 10µs/div 33 1.0V 1ms/div 34 1.0V 10µs/div CRT 37 50V 10µs/div NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram. MECHANICAL EXPLODED VIEW 201 111 201 201 201 201 115 204 204 J801 201 114 108 115 105 PCB110 (CRT PCB) 104 115 201 104 203 103 L503 205 102 115 FB401 114 V801 114 PCB330 (COMB PCB) PCB010 (MAIN PCB) 203 PCB250 (P-IN-P PCB) 205 202 205 116 117 203 203 112 SP1001 113 204 110 204 204 PCB170 (VIDEO JACK PCB) 106 107 109 101 204 MECHANICAL REPLACEMENT PARTS LIST Location No. TSB P/N Reference No. Description 101 102 103 104 105 106 107 108 109 AD300867 AD300757 AD300758 BZ710260 AD300759 AD300760 AD300761 AD300762 AD300763 A3K102E720 771WPA0263 899EFBA001 899HV3T000 741WUA0021 701APJ0082 712APB0001 702APA0128 711WPA0149 CABINET,FRONT ASSY PLATE,JACK WIRING CLIP HOLDER,ANODE WIRE SPRING,EARTH CABINET,FRONT DOOR CABINET,BACK PLATE,FRONT 110 111 112 113 114 115 116 117 AD300764 AD300868 AD300766 AD300767 AD300768 BZ710033 AD300870 AD300869 713WPA0163 7225490054 7260000306 735WPB0134 762WPA0009 8111J50D05 752WSA0184 752WSA0163 GLASS,LED SHEET,RATING SHEET,CAUTION BUTTON,ASS'Y HOLDER,CRT WIRE SCREW,TAPPING(A) GW22 SHIELD,CASE IF SHIELD,COVER IF 201 202 203 204 205 BZ710036 AD300769 BZ710019 BZ710031 BZ710239 8117540B04 8117330A04 8109630802 8110630A04 8109I30A04 SCREW,TAPPING(B0) TRUSS SCREW,TAPPING(B0) FLAT SCREW,TAP TITE(B) BRAZIER SCREW,TAP TITE(P) BRAZIER SCREW,TAP TITE(B) WH7 --------------------- AD300770 AD300771 AD300772 AD300773 AD300871 AD300872 AD300775 AD300776 AD300777 AD300779 791AHA0024 792AHA0085 792AHA0086 793ACD0500 A3K102E975 J3K10201 J3K10516 J3K10517 J3K10536 JA4LD400 FILM BAG PACKAGE,TOP PACKAGE,BOTTOM GIFT BOX INSTRUCTION BOOK KIT INSTRUCTION BOOK IMPORTANT SAFETY REGISTRATION CARD ESP CARD POLY BAG 5x35 4x20 3x10 3x8 3x10 3x10 ELECTRICAL REPLACEMENT PARTS LIST Location No. USA-TOSHIBA Reference No. RESISTORS ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! R055 R416 R418 R420 R422 R426 R435 R436 R438 R439 R441 R500 R501 R505 R517 R521 R522 R527 R542 R543 R554 R621 ! R804 ! R806 ! R808 AD300041 AD300416 BZ210105 BZ210053 BZ210013 BZ210105 AD300655 BZ210090 BZ210190 AD300043 AD300036 BZ210080 AD300720 AD300038 AD300042 AD300041 AD300041 BZ210149 AD300721 BZ210064 AD300722 AD300849 BZ210050 BZ210050 BZ210050 R3X18A270J R002T25R6J R4X5T6183F R002T22R2J R4X5T4104F R4X5T6183F R903N8222J R4X5T6822F R63581R22J R3X181102J R4X5T6562F R0G3K2275K R5X2AE1R2J R3X20B473J R3X18A010J R3X18A270J R3X18A270J R3X18AR68J R3X281R15J R63584681J R002T2273J R00202121J R3X18A123J R3X18A123J R3X18A123J ! C408 ! C413 C418 ! C420 ! C421 ! C423 C425 ! C426 ! C430 ! C501 ! C502 ! C503 ! C504 ! C505 ! C506 ! C507 ! C508 ! C510 ! C513 C517 ! C519 ! C521 ! C522 ! C523 ! C527 ! C531 ! C534 C535 C536 ! C542 C808 C1003 C1004 C1009 BZ110101 AD300067 BZ110056 AD300723 BZ110125 BZ110125 AD300077 AD300061 AD300064 AD300067 AD300078 AD300078 BZ110074 BZ110145 BZ110145 BZ110012 AD300726 BZ110018 AD300726 BZ110115 AD300726 AD300060 AD300727 AD300060 BZ110119 BZ110081 BZ110152 BZ110115 BZ110115 AD300728 AD300078 AD300067 BZ110053 BZ110053 E5EZF3222M E02LF4102M P447F2474J P4N8FJ153H C0JLYR7Q2K C0JLYR7Q2K C0JLYR713K E5EZFD220M E02LT8220M E02LF4102M C0JBB0713K C0JBB0713K E50HU5010M P2472B104M P2472B104M E51CGC471M CB3LB0MQ2K E5EZT4101M CB3LB0MQ2K C0JLYR7H3K CB3LB0MQ2K E62NFB101M CB3LE0ML3M E62NFB101M E02LF2222M E02LT2471M C0JLYR7B3K C0JLYR7H3K C0JLYR7H3K E02LF5471M C0JBB0713K E02LF4102M E02LF3102M E02LF3102M D001 D101 D102 D103 D106 D107 D108 D109 D110 D111 D201 ! D401 D402 D403 D404 ! D405 AD300729 BZ410020 BZ410006 BZ410006 BZ410006 BZ410006 BZ410021 BZ410054 BZ410022 BZ410022 AD300070 AD300069 BZ410043 BZ410019 BZ410023 BZ410063 D97U03301A D97U05R11B D1VT001330 D1VT001330 D1VT001330 D1VT001330 D97U05R61B 0021721150 D97U06R81B D97U06R81B D97U01201B D97U02701B D2WT011E10 D97U03001B D97U09R11B D2WTAU02A0 R,METAL RC R,METAL RC R,METAL R,METAL RC R,METAL R,FUSE R,METAL OXIDE R,METAL RC R,CEMENT R,METAL R,METAL OXIDE R,METAL OXIDE R,METAL OXIDE R,METAL OXIDE R,METAL R,FUSE RC RC R,METAL OXIDE R,METAL OXIDE R,METAL OXIDE Description 27 OHM 2W 5.6 OHM 1/2W 18K OHM 1/6W 2.2 OHM 1/2W 100K OHM 1/4W 18K OHM 1/6W 2.2K OHM 1/8W 8.2K OHM 1/6W 0.22 OHM 1W 1K OHM 1W 5.6K OHM 1/6W 2.7M OHM 1/2W 1.2 OHM 7W 47K OHM 3W 1 OHM 2W 27 OHM 2W 27 OHM 2W 0.68 OHM 2W 0.15 OHM 1W 680 OHM 1/4W 27K OHM 1/2W 120 OHM 1/2W 12K OHM 2W 12K OHM 2W 12K OHM 2W CAPACITORS CE CE CMPP CMPP CC CC CC CE CE CE CC CC CE CMP CMP CE CC CE CC CC CC CE CC CE CE CE CC CC CC CE CC CE CE CE 2200 UF 25V 1000 UF 35V 0.47 UF 200V FHS 0.015 UF 1.25KV 470 PF 2KV YR 470 PF 2KV YR 0.001 UF 2KV YR 22 UF 250V 22 UF 100V 1000 UF 35V 0.001 UF 2KV B 0.001 UF 2KV B 1 UF 50V 0.1 UF 275V PHE840 0.1 UF 275V PHE840 470 UF 200V 470 PF 250V 100 UF 35V 470 PF 250V 0.0022UF 2KV YR 470 PF 250V 100 UF 160V 0.0033UF 250V 100 UF 160V 2200 UF 16V 470 UF 16V 0.0012UF 2KV YR 0.0022UF 2KV YR 0.0022UF 2KV YR 470 UF 50V 0.001 UF 2KV B 1000 UF 35V 1000 UF 25V 1000 UF 25V DIODES DIODE,ZENER DIODE,ZENER DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,ZENER LED DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,SILICON DIODE,ZENER DIODE,ZENER DIODE,SILICON MTZJ33A T-77 MTZJ5.1B T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 MTZJ5.6B T-77 SLR-342VCT32 MTZJ6.8B T-77 MTZJ6.8B T-77 MTZJ12B T-77 MTZJ27B T-77 11E1-EIC MTZJ30B T-77 MTZJ9.1B T-77 AU02A-EIC ELECTRICAL REPLACEMENT PARTS LIST Location No. USA-TOSHIBA Reference No. DIODES ! D406 ! D407 D410 ! D411 ! D501 ! D502 ! D503 ! D504 ! D505 ! D506 D507 D508 ! D509 ! D510 ! D511 ! D512 D513 ! D514 D515 D516 D517 D518 D519 D520 ! D521 ! D527 D528 ! D529 ! D530 ! D531 D601 D602 D603 D604 D605 D606 D607 D608 D611 D612 D613 D614 D615 D711 D750 D801 D802 D803 D807 D808 D809 D1801 AD300071 BZ410063 BZ410019 BZ410063 BZ410085 BZ410085 BZ410085 BZ410085 BZ410052 AD300731 BZ410006 BZ410006 AD300075 AD300076 AD300731 BZ410076 BZ410021 BZ410076 AD300732 BZ410006 BZ410006 BZ410006 BZ410006 BZ410006 BZ410006 BZ410085 BZ410021 BZ410085 BZ410085 BZ410085 BZ410006 BZ410066 BZ410066 BZ410066 BZ410043 AD300850 BZ410006 BZ410006 BZ410006 BZ410006 BZ410006 BZ410006 BZ410006 BZ410066 BZ410006 BZ410006 BZ410006 BZ410006 BZ410006 BZ410006 BZ410006 BZ410006 D97U01101B D2WTAU02A0 D97U03001B D2WTAU02A0 D2WXN40050 D2WXN40050 D2WXN40050 D2WXN40050 D28F21DQN9 D2WXN49370 D1VT001330 D1VT001330 D28TELS6N6 D28F30DF60 D2WXN49370 D2WXB290S0 D97U05R61B D2WXB290S0 D28XQS04N0 D1VT001330 D1VT001330 D1VT001330 D1VT001330 D1VT001330 D1VT001330 D2WXN40050 D97U05R61B D2WXN40050 D2WXN40050 D2WXN40050 D1VT001330 D97U06R21B D97U06R21B D97U06R21B D2WT011E10 D97X05R61B D1VT001330 D1VT001330 D1VT001330 D1VT001330 D1VT001330 D1VT001330 D1VT001330 D97U06R21B D1VT001330 D1VT001330 D1VT001330 D1VT001330 D1VT001330 D1VT001330 D1VT001330 D1VT001330 ! IC051 IC101 IC103 IC198 IC201 IC303 ! IC401 ! IC501 ! IC502 ! IC503 ! IC504 IC701 IC750 IC751 IC902 ! IC1001 IC1501 IC1801 ! IC1802 IC1803 BZ611015 AD300851 AD300050 AD300852 AD300058 BZ611034 AD300414 BZ611036 BZ611033 BZ611015 BZ410040 AD300054 AD300853 BZ611049 AD300059 AD300056 AD300609 AD300854 AD300855 AD300856 I1KA97805A I56D07062A I9UJ0T600C A3K102E015 I05DC12530 I06DF62420 I03TD80410 I2BT06624G I1KA97809A I1KA97805A 0002500560 I0UD013110 I07S07645N I0UF012340 I01FF58290 I0FSP52760 I05FE90A45 I06FE56640 I0UF9563F0 I55F0ET080 Q101 Q102 Q103 BZ510002 BZ510002 BZ510071 T8YJ2412K0 T8YJ2412K0 TNAAB05003 Description DIODE,ZENER DIODE,SILICON DIODE,ZENER DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SCHOTTKY DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,RECTIFER DIODE,RECTIFIER DIODE,SILICON DIODE,SILICON DIODE,ZENER DIODE,SILICON DIODE,SCHOTTKY DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,ZENER DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,ZENER DIODE,ZENER DIODE,ZENER DIODE,SILICON DIODE,ZENER DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,ZENER DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON MTZJ11B T-77 AU02A-EIC MTZJ30B T-77 AU02A-EIC 1N4005-EIC 1N4005-EIC 1N4005-EIC 1N4005-EIC 21DQ09N-FC4 1N4937 1SS133T-77 1SS133T-77 10ELS6N-TA1B2 30DF6-FC 1N4937 SB290S MTZJ5.6B T-77 SB290S 11EQS04N-TA2B5 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1N4005-EIC MTZJ5.6B T-77 1N4005-EIC 1N4005-EIC 1N4005-EIC 1SS133T-77 MTZJ6.2B T-77 MTZJ6.2B T-77 MTZJ6.2B T-77 11E1-EIC MTZJ5.6B T-72 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 MTZJ6.2B T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 1SS133T-77 ICS IC IC IC IC IC IC IC IC IC IC PHOTO COUPLER IC IC IC IC IC IC IC IC IC KIA7805API OEC7062A PST600C S-24C16AFJA-TB-01 TB1253N M62420SP LA78041 STR-G6624 KIA7809API KIA7805API TLP621(D4-GR-LF2) MM1311AD BA7645N MM1234 AN5829S AN5276 TC90A45F M65664FP MM1563F TC7SET08F TRANSISTORS TRANSISTOR,SILICON TRANSISTOR,SILICON COMPOUND TRANSISTOR 2SC2412KT146 R,S 2SC2412KT146 R,S KRC102RTK ELECTRICAL REPLACEMENT PARTS LIST Location No. USA-TOSHIBA Q107 Q109 Q201 Q202 Q203 Q204 Q402 Q405 Q406 Q501 Q504 Q507 Q508 Q509 Q510 Q511 Q512 Q603 Q604 Q701 Q704 Q705 Q709 Q750 Q751 Q752 Q753 Q754 Q755 Q801 Q802 Q803 Q810 Q811 Q812 Q1001 Q1501 Q1502 Q1503 Q1504 Q1803 Q1804 Q1805 Q1806 Q1807 Q1808 BZ510068 BZ510002 BZ510002 BZ510002 BZ510001 AD300734 BZ510027 BZ510040 BZ510049 BZ510070 BZ510069 BZ510069 AD300611 BZ510071 BZ510031 BZ510070 BZ510004 BZ510002 BZ510002 BZ510002 BZ510002 BZ510002 BZ510001 BZ510002 BZ510001 BZ510002 BZ510002 BZ510002 BZ510001 BZ510027 BZ510027 BZ510027 AD300442 AD300442 AD300442 BZ510068 BZ510002 BZ510001 BZ510002 BZ510002 BZ510002 BZ510002 BZ510002 BZ510002 BZ510002 BZ510001 TNAAJ05003 T8YJ2412K0 T8YJ2412K0 T8YJ2412K0 T6YJ1037K0 T8AA03881S TC3Q026210 TDUU024990 TPYJD05001 TCAT032034 TCATC31980 TCATC31980 TAAT01273Y TNAAB05003 TD3T007340 TCAT032034 TA3T016240 T8YJ2412K0 T8YJ2412K0 T8YJ2412K0 T8YJ2412K0 T8YJ2412K0 T6YJ1037K0 T8YJ2412K0 T6YJ1037K0 T8YJ2412K0 T8YJ2412K0 T8YJ2412K0 T6YJ1037K0 TC3Q026210 TC3Q026210 TC3Q026210 TCYT1740S0 TCYT1740S0 TCYT1740S0 TNAAJ05003 T8YJ2412K0 T6YJ1037K0 T8YJ2412K0 T8YJ2412K0 T8YJ2412K0 T8YJ2412K0 T8YJ2412K0 T8YJ2412K0 T8YJ2412K0 T6YJ1037K0 L002 L101 L202 L203 L204 L205 L301 L302 ! L402 ! L501 ! L503 L601 L602 L603 L604 L701 L703 L750 L751 L753 L802 L803 L804 L901 L1501 L1502 L1503 L1506 L1801 L1802 BZ310002 AD300121 BZ310101 BZ310101 BZ310043 BZ310003 BZ310029 BZ310058 BZ310063 AD300402 AD300735 BZ310003 BZ310002 BZ310040 BZ310040 BZ310005 BZ310040 BZ310041 BZ310002 BZ310041 AD300123 AD300123 AD300123 BZ310058 BZ310052 BZ310043 AD300614 BZ310058 BZ310053 AD300857 021673101K 021LA62R7K 0216A61R2K 0216A61R2K 021LA6150K 021673470K 021LA6470K 021LA6220K 022100027A 029X000098 028R270008 021673470K 021673101K 02167F470J 02167F470J 02167D101K 02167F470J 02167F101J 021673101K 02167F101J 021673151K 021673151K 021673151K 021LA6220K 021LA6100K 021LA6150K 021673821K 021LA6220K 021673100K 02167D471K ! ! ! ! ! ! ! ! ! ! ! ! ! ! Reference No. TRANSISTORS Description COMPOUND TRANSISTOR TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON COMPOUND TRANSISTOR TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON COMPOUND TRANSISTOR TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON COMPOUND TRANSISTOR TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON KRC111RTK 2SC2412KT146 R,S 2SC2412KT146 R,S 2SC2412KT146 R,S 2SA1037AKT146R,S KTC3881S-RTK 2SC2621(D,E)-RAC 2SD2499(LB0EC1) DTA144EKAT146 KTC3203_Y-AT KTC3198-AT(Y,GR) KTC3198-AT(Y,GR) KTA1273_Y KRC102RTK 2SD734(E,F)-AA KTC3203_Y-AT 2SA1624-AA 2SC2412KT146 R,S 2SC2412KT146 R,S 2SC2412KT146 R,S 2SC2412KT146 R,S 2SC2412KT146 R,S 2SA1037AKT146R,S 2SC2412KT146 R,S 2SA1037AKT146R,S 2SC2412KT146 R,S 2SC2412KT146 R,S 2SC2412KT146 R,S 2SA1037AKT146R,S 2SC2621(D,E)-RAC 2SC2621(D,E)-RAC 2SC2621(D,E)-RAC 2SC1740SP(R,S) TP 2SC1740SP(R,S) TP 2SC1740SP(R,S) TP KRC111RTK 2SC2412KT146 R,S 2SA1037AKT146R,S 2SC2412KT146 R,S 2SC2412KT146 R,S 2SC2412KT146 R,S 2SC2412KT146 R,S 2SC2412KT146 R,S 2SC2412KT146 R,S 2SC2412KT146 R,S 2SA1037AKT146R,S COILS &TRANSFORMERS COIL COIL COIL COIL COIL COIL COIL COIL COIL,LINEARITY COIL,LINE FILTER COIL,DEGAUSS COIL COIL COIL COIL COIL COIL COIL COIL COIL COIL COIL COIL COIL COIL COIL COIL COIL COIL COIL 100 UH 2.7 UH 1.2 UH 1.2 UH 15 UH 47 UH 47 UH 22 UH ELH5L4113 SS28H-20075 8R270008 47 UH 100 UH 47 UH 47 UH 100 UH 47 UH 100 UH 100 UH 100 UH 150 UH 150 UH 150 UH 22 UH 10 UH 15 UH 820 UH 22 UH 10 UH 470 UH ELECTRICAL REPLACEMENT PARTS LIST Location No. USA-TOSHIBA Reference No. COILS &TRANSFORMERS L1804 L1805 T401 ! T501 AD300612 AD300612 AD300736 AD300737 02167F100J 02167F100J 045013002J 048140064S J203 J701 J702 J703 J704 J705 J706 J707 ! J801 BZ614203 BZ614203 AD300108 BZ614203 AD300738 AD300739 AD300740 AD300741 BZ614057 060Q431018 060Q431018 063Q700002 060Q431018 060Q411017 060Q401048 060Q401049 060Q421018 066C130015 SW101 SW102 SW103 SW104 SW105 BZ612001 BZ612001 BZ612001 BZ612001 BZ612001 0504201T31 0504201T31 0504201T31 0504201T31 0504201T31 VR401 VR502 BZ210194 BZ210067 V1263H3BT7 V116314BTC PCB010 PCB110 PCB170 PCB250 PCB330 AD300858 AD300743 AD300859 AD300860 AD300745 A3K102E010K A3K106E110K A3K102E170K A3K102E250K A3K106E330K B502 B504 B505 CD501 CD702 CD801 CD803 CD805 CF201 CF202 CF203 CF204 CP001 CP051 CP101 CP401 CP501 CP502 CP503 CP504 CP751 CP752 CP803 CP804 CP805 CP806 CD701A CP1001 CP1501 CP702A CP702B CP801A CUS011 BZ310122 BZ310121 BZ310015 AD300746 AD300747 AD300748 BZ614175 BZ614175 BZ613015 BZ613022 AD300686 AD300513 AD300862 AD300862 BZ614238 AD300749 BZ614176 BZ614018 AD300751 AD300751 AD300864 AD300864 BZ614017 BZ614058 BZ614213 BZ614017 AD300622 AD300097 AD300102 AD300752 BZ614276 BZ614273 BZ710279 BZ710001 BZ614044 BZ614043 BZ614125 AD300753 BZ614005 BZ614005 BZ614171 AD300114 AD300754 BZ410079 AD300865 AD300691 AD300755 024HT03563 024HT03553 024AT03482 120R615901 06CU252002 06CU2A3401 06CU82039A 06CU82039A 1011T4R504 1022T45R74 1012T4R519 1012T04702 069J190048 069J190048 0697260650 069W340018 069S320419 069W420029 069D010010 069D010010 069J190038 069J190038 069W320018 069W010010 069S2A0629 069W320018 06CH243001 069W14T299 069J160260 069S250629 067U005049 067U010049 800WFAA006 800WF00004 124120301A 124116281A 081PC6R304 043227008R 06710T0006 06710T0006 077Q014003 0560V20115 070Y435002 DF5EL3R0A0 07660DU020 0145S00052 098T270601 Description COIL COIL TRANS,HORIZONTAL DRIVE TRANSFORMER,SWITCHING 10 UH 10 UH ZTS7196-3 8140064S JACKS RCA JACK RCA JACK JACK RCA JACK RCA JACK RCA JACK RCA JACK RCA JACK SOCKET,CATHODE RAY TUBE AV3-19DS-1 AV3-19DS-1 YKF51-5503 AV3-19DS-1 AV3-19D-5 AV1-06D-3 AV1-06D-4 AV1-06DS-2 CVT3275-5102 SWITCHES SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SKHVBED010 SKHVBED010 SKHVBED010 SKHVBED010 SKHVBED010 VARIABLE RESISTORS VOLUME,SEMI FIXED VOLUME,SEMI FIXED RH0683CJ3R EVNCYAA03B14 P.C.BOARD ASSEMBLIES PCB ASS'Y PCB ASS'Y PCB ASS'Y PCB ASS'Y PCB ASS'Y TMA509B TCA367A TEAA68B TEAA69A TEAA70A MISCELLANEOUS ! ! ! ! ! ! ! ! ! ! ! EL001 EL002 F501 FB401 FH501 FH502 OS101 RY501 SP1001 TH501 TM101 TU001 V801 CORE,BEADS CORE,BEADS CORE,BEADS CORD,AC BUSH CORD,CONNECTOR CORD,CONNECTOR CORD,CONNECTOR CORD,CONNECTOR FILTER,CERAMIC FILTER,SAW FILTER,CERAMIC TRAP FILTER,CERAMIC TRAP CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CORD,CONNECTOR CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE WIRE HOLDER WIRE HOLDER CUSHION A CUSHION-A EYE LET EYE LET FUSE TRANSFORMER,FLYBACK HOLDER,FUSE HOLDER,FUSE REMOTE RECEIVER RELAY SPEAKER DEGAUSS ELEMENT TRANSMITTER TUNER,VHF-UHF CRT W/DY W4BRH3.5X6X1.0X2 W5RH3.5X5X1.0 BL02RN2-R62T4 0R615901 CU252002 CU2A3401 SM1098-009-1A SM1098-009-1A EFCT4R5YS5A SAF45MFG220Z TPSRA4M50C00-A0 MKT47.3MC110P-TF IMSA-9130S-09L IMSA-9130S-09L TKC-M06X-A1 TS-80P-04-V1 A3963WV2-3PD TV-50P-02-A1 005P-2100 005P-2100 IMSA-9130B-09 IMSA-9130B-09 TS-80P-02-V1 005P-2100 A2001WV2-10P TS-80P-02-V1 CH243001 TID-X04P-Z1 6035B-06Z002-T A2001WV2-5P B2013H02-5P B2013H02-10P or XRY20X30BD XRY16X28BD 51MS063LCC 3227008R EYF-52BC EYF-52BC PIC-28143SY-2 ALKS321 070Y435002 ZPB45BL3R0A SBKM0P011A ENV56D66G3 A68AJB82X10 ELECTRICAL REPLACEMENT PARTS LIST Location No. USA-TOSHIBA Reference No. MISCELLANEOUS X101 X601 X1801 AD300624 BZ613004 AD300866 1001T8R004 100CT3R505 100DT01405 RC................... CARBON RESISTOR CC................... CE................... CP................... CPP.................. CPL.................. CMP....................... CMPL................ CMPP................ CERAMIC CAPACITOR ALUMI ELECTROLYTIC CAPACITOR POLYESTER CAPACITOR POLYPROPYLENE CAPACITOR PLASTIC CAPACITOR METAL POLYESTER CAPACITOR METAL PLASTIC CAPACITOR METAL POLYPROPYLENE CAPACITOR CERAMIC,OSCILLATOR CRYSTAL CRYSTAL RESISTOR CAPACITORS Description EFOEC8004T4 HC-49/C AT-49 TOSHIBA AMERICA CONSUMER PRODUCTS,INC. HEAD OFFICE / 82 TOTOWA ROAD,WAYNE,NEW JERSEY 07470 U.S.A. TOSHIBA HAWAII,INC. HEAD OFFICE / 327 KAMAKEE STREET,HONOLULU,HAWAII 96814 U.S.A.