Download Kenwood KVT-729DVD Car Video System User Manual
Transcript
MONITOR WITH DVD RECEIVER KVT-729DVD INSTALLATION MANUAL © B54-4516-00/00 (EV) B54-4516-00_00.indd 1 07.1.9 7:20:49 PM Accessories 1 0 ..........1 2 ..........1 ! ..........1 ..........2 3 ..........1 4 ..........1 5 ..........1 6 ..........2 7 ..........4 8 ..........4 9 ..........2 2 | KVT-729DVD B54-4516-00_00.indd 2 07.1.9 7:20:49 PM Installation Procedure 1. To prevent short circuits, remove the key from the ignition and disconnect the - terminal of the battery. 2. Make the proper input and output wire connections for each unit. 3. Connect the wire on the wiring harness. 4. Take Connector B on the wiring harness and connect it to the speaker connector in your vehicle. 5. Take Connector A on the wiring harness and connect it to the external power connector on your vehicle. 6. Connect the wiring harness connector to the unit. 7. Install the unit in your car. 8. Reconnect the - terminal of the battery. 9. Press the reset button. 2WARNING • If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box. • Do not cut out the fuse from the ignition wire (red) and the battery wire (yellow). The power supply must be connected to the wires via the fuse. ¤ • If the power is not turned ON (or it is ON, but will be OFF immediately), the speaker wire may have a short-circuit or touched the chasis of the vehicle and the protection function may have been activated. Therefore, the speaker wire should be checked. • If your car is not prepared for this special connectionsystem, consult your Kenwood dealer. • Only use antenna conversion adapters (ISO-JASO) when the antenna cord has an ISO plug. • Make sure that all wire connections are securely made by inserting jacks until they lock completely. • If your vehicle’s ignition does not have an ACC position, or if the ignition wire is connected to a power source with constant voltage such as a battery wire, the power will not be linked with the ignition (i.e., it will not turn on and off along with the ignition). If you want to link the unit’s power with the ignition, connect the ignition wire to a power source that can be turned on and off with the ignition key. • If the fuse blows, first make sure that the wires have not caused a short circuit, then replace the old fuse with one with the same rating. • Insulate unconnected wires with vinyl tape or other similar material. To prevent short circuits, also do not remove the caps on the ends of the unconnected wires or the terminals. • Connect the speaker wires correctly to the terminals to which they correspond. The unit may receive damage or fail to work if you share the - wires and/or ground them to any metal part in the car. • After the unit is installed, check whether the brake lamps, indicators, wipers, etc. on the car are working properly. • If the console has a lid, make sure to install the unit so that the faceplate does not hit the lid when closing and opening. • Mount the unit so that the mounting angle is 30° or less. English | B54-4516-00_00.indd 3 3 07.1.9 7:20:50 PM Connection Monitor/Player unit USB device (commercially available) Do not connect. USB connector Accessory ! Wiring harness (Accessory 2) Ground wire (Black) Ground wire (Black) FUSE ( 5A ) Connector A Battery wire (Yellow) 8 7 6 5 4 3 2 1 8 7 6 5 4 3 2 1 BATT The cable (Accessory 3) is fixed with a chassis using harness band (Accessory !). Ignition wire (Red) ACC Accessory 0 (ISO–JASO) Connector B Antenna Cord (ISO) (Orange/White) Accessory 4 FUSE ( 10A ) Dimmer control wire (Orange/White) Connect to the vehicle's parking brake detection switch harness using the supplied relay connector. For the sake of safety, be sure to connect the parking sensor. Parking sensor wire (Light Green) PRK SW To vehicle's reverse lamp harness To steering remote Connect to the terminal that is grounded when either the telephone rings or during conversation. To connect the Kenwood navigation system, consult your navigation manual. Connect either to the power control terminal when using the optional power amplifier, or to the antenna control terminal in the vehicle. To "EXT.AMP.CONT." terminal of the amplifier having the external amp control function. Reverse sensor wire (Purple/White) Steering remote control input (Light Blue/Yellow) Mute wire (Brown) Power control/ Motor antenna control wire (Blue/White) External amplifier control wire (Pink/Black) If no connections are made, do not let the cable come out from the tab. 4 | KVT-729DVD B54-4516-00_00.indd 4 07.1.9 7:20:50 PM Receiver unit Accessory ! Accessory 3 Receiver unit The cable (Accessory 3) is fixed with a chassis using harness band (Accessory !). FM/AM antenna input Wiring harness (Accessory 1) ILLUMI Ground wire (Black) - (To car chassis) A REVERSE REMO.CONT MUTE A + ANT CONT P. CONT Battery EXT. CONT If you connect the ignition wire (red) and the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box. English | B54-4516-00_00.indd 5 5 07.1.9 7:20:52 PM Connecting Wires to Terminals Connector Function Guide Pin Numbers for ISO Connectors External Power Connector A-4 A-5 A-6 A-7 A-8 Cable Colour Functions Yellow Blue/White Orange/White Red Black Battery Power Control Dimmer Ignition (ACC) Earth (Ground) Connection Speaker Connector B-1 B-2 B-3 B-4 B-5 B-6 B-7 B-8 Purple Purple/Black Gray Gray/Black White White/Black Green Green/Black Rear Right (+) Rear Right (–) Front Right (+) Front Right (–) Front Left (+) Front Left (–) Rear Left (+) Rear Left (–) 2WARNING Connecting the ISO Connector The pin arrangement for the ISO connectors depends on the type of vehicle you drive. Make sure to make the proper connections to prevent damage to the unit. The default connection for the wiring harness is described in 1 below. If the ISO connector pins are set as described in 2 or 3, make the connection as illustrated. Please be sure to reconnect the cable as shown 2 below to install this unit to the Volkswagen vehicles etc. 1 (Default setting) The A-7 pin (red) of the vehicle’s ISO connector is linked with the ignition, and the A4 pin (yellow) is connected to the constant power supply. Ignition cable (Red) A-7 Pin (Red) Unit Battery cable (Yellow) Vehicle A-4 Pin (Yellow) 2 The A-7 pin (red) of the vehicle’s ISO connector is connected to the constant power supply, and the A-4 pin (yellow) is linked to the ignition. Ignition cable A-7 Pin (Red) Unit Battery cable (Yellow) Vehicle A-4 Pin (Yellow) 3 The A-4 pin (yellow) of the vehicle’s ISO connector is not connected to anything, while the A-7 pin (red) is connected to the constant power supply (or both the A-7 (red) and A-4 (yellow) pins are connected to the constant power supply). Ignition cable (Red) Unit Battery cable (Yellow) A-7 Pin (Red) Vehicle A-4 Pin (Yellow) ⁄ • When the connection is made as in 3 above, the unit’s power will not be linked to the ignition key. For that reason, always make sure to turn off the unit’s power when the ignition is turned off. To link the unit’s power to the ignition, connect the ignition cable (ACC...red) to a power source that can be turned on and off with the ignition key. 6 | KVT-729DVD B54-4516-00_00.indd 6 07.1.9 7:20:54 PM System Connection Receiver unit ■ Front Preout • Audio left output (White) • Audio right output (Red) ■ Rear Preout • Audio left output (White) • Audio right output (Red) ■ Subwoofer Preout • Audio left output (White) • Audio right output (Red) ■ Audio/Visual input • Visual input (Yellow) • Audio left input (White) • Audio right input (Red) ■ Rear View Camera Input • Visual input (Yellow) ■ Audio/Visual Output • Visual output (Yellow) • Audio left output (White) • Audio right output (Red) English | B54-4516-00_00.indd 7 7 07.1.9 7:20:54 PM Optional Accessory Connection iPod (commercially available) iPod AUDIO IN KCA-iP300V (Optional Accessory) Audio Input Resistance-free stereo type mini plug (3.5Ф) iPod VIDEO IN Audio Output (Black) Visual Input Resistance-free mini plug (3.5Ф) Monitor/Player unit Visual Output (Yellow) USB terminal USB terminal Receiver unit Accessory 3 Connection cable (Included in the Navigation System) Connection cable (Included in the Disc changer) Disc Changer etc. (Optional Accessory) Navigation System (Optional Accessory) TV Tuner (Optional Accessory) TV ANTENNA INPUT TO MONITOR UNIT Connection cable (Included in the TV tuner) 8 | KVT-729DVD B54-4516-00_00.indd 8 07.1.9 7:20:55 PM Installation for Monitor/Player Unit Firewall or metal support Screw (M4X8) (commercially available) Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. Self-tapping screw (commercially available) Metal mounting strap (commercially available) Accessory 5 Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (eg, the sound may skip). Installation for Receiver Unit 1. Attach the installation brackets 9 to the sides of the receiver unit using the sems bolts 7. Installation brackets (Accessory 9) Sems bolts (M4 × 8 mm) (Accessory 7) 2. Use the tapping screw 8 to secure the receiver unit to the audio board. Tapping screw (ø4 × 16 mm) (Accessory 8) English | B54-4516-00_00.indd 9 9 07.1.9 7:20:57 PM Removing Monitor/Player Unit Removing the Hard Rubber Frame (escutcheon) 1. Engage the catch pins on the removal tool 6 and remove the two locks on the lower level. Lower the frame and pull it forward as shown in the figure. Removal Tool (Accessory 6) Removing the Unit 1. Remove the hard rubber frame by referring to the removal procedure in the section <Removing the Hard Rubber Frame>. 2. Remove the Hex-head screw with integral washer (M4 × 8) on the back panel. 3. Insert the two removal tools 6 deeply into the slots on each side, as shown. Removal Tool (Accessory 6) Catch Lock ⁄ • The frame can be removed from the top side in the same manner. 4. Lower the removal tool toward the bottom, and pull out the unit halfway while pressing towards the inside. 2. When the lower level is removed, remove the upper two locations. ⁄ • Be careful to avoid injury from the catch pins on the removal tool. 5. Pull the unit all the way out with your hands, being careful not to drop it. 10 | KVT-729DVD B54-4516-00_00.indd 10 07.1.9 7:20:57 PM B54-4516-00_00.indd 11 07.1.9 7:20:58 PM B54-4516-00_00.indd 12 07.1.9 7:20:58 PM