Download Scag Power Equipment ST 17KA Tractor Operator`s manual
Transcript
OPERATOR’S MANUAL MODEL SWZ THIS MANUAL CONTAINS THE OPERATING INSTRUCTIONS AND SAFETY INFORMATION FOR YOUR SCAG MOWER. READING THIS MANUAL CAN PROVIDE YOU WITH ASSISTANCE IN MAINTENANCE AND ADJUSTMENT PROCEDURES TO KEEP YOUR MOWER PERFORMING TO MAXIMUM EFFICIENCY. THE SPECIFIC MODELS THAT THIS BOOK COVERS ARE CONTAINED ON THE INSIDE COVER. BEFORE OPERATING YOUR MACHINE, PLEASE READ ALL THE INFORMATION ENCLOSED. PART NUMBER 03073 WARNING: FAILURE TO FOLLOW SAFE OPERATING PRACTICES MAY RESULT IN SERIOUS INJURY. * Keep all shields in place, especially the grass discharge chute. * Before performing any maintenance or service, stop the machine and remove the spark plug wire and ignition key. * If a mechanism becomes clogged, stop the engine before cleaning. * Keep hands, feet and clothing away from power-driven parts. * Read this manual completely as well as other manuals that came with your mower. * Keep others off the tractor (only one person at a time) REMEMBER - YOUR MOWER IS ONLY AS SAFE AS THE OPERATOR! Hazard control and accident prevention are dependent upon the awareness, concern, prudence, and proper training of the personnel involved in the operation, transport, maintenance, and storage of the equipment. This manual covers the operating instructions and illustrated parts list for: SWZ36-14KA SWZ36-15KH SWZ48-14KA SWZ48-15KH SWZ48-17KA SWZ48A-17KA SWZ52-17KA SWZ52A-17KA SWZ52-17KAE SWZ-21KAE SWM-61/E SWM-72/E SWM-52A with a serial number of 5120001 to 5129999 with a serial number of 5130001 to 5139999 with a serial number of 5140001 to 5149999 with a serial number of 5150001 to 5159999 with a serial number of 5160001 to 5169999 with a serial number of 5170001 to 5179999 with a serial number of 5180001 to 5189999 with a serial number of 5190001 to 5199999 with a serial number of 5970001 to 5979999 with a serial number of 5210001 to 5219999 with a serial number of 5230001 to 5239999 with a serial number of 5240001 to 5249999 with a serial number of 5250001 to 5259999 Always use the entire serial number listed on the serial number tag when referring to this product. TABLE OF CONTENTS SUBJECT PAGE Introduction .................................................................................................. 1 General Safety Instructions .......................................................................... 1 Signal Words ............................................................................................... 1 Before Operating ......................................................................................... 2 While Operating ........................................................................................... 2 Maintenance and Storage ........................................................................... 3 Initial Run-In Procedures ............................................................................. 4 Mower Operation ......................................................................................... 4 Cutter Deck Belt Adjustments ...................................................................... 5 Cutter Deck Adjustments ............................................................................. 6 Blade Height Adjustments ........................................................................... 6 Cutter Blades ............................................................................................... 7 Neutral Adjustment ...................................................................................... 7 Steering Control Rod Adjustment ................................................................ 8 Tracking Adjustment .................................................................................... 8 Parking Brake .............................................................................................. 8 Lubrication and Maintenance Chart ............................................................ 9 Troubleshooting Cutting Conditions ............................................................ 10-12 Technical Specifications .............................................................................. 13-14 Notes .........................................................................................................................15 MEMBER c WE SUPPORT OPE Equipment & Engine Training Council TECHNICIAN CERTIFICATION I TABLE OF CONTENTS (CONTINUED) SUBJECT PAGE Illustrated Parts List SWM-36"Cutter Deck ........................................................................ 16-17 SWM-48", 52", 61", 72" Cutter Decks...................................................... 18-19 Engine Deck................................................................................................ 20-21 Drive And Brake Components.................................................................. 22-23 Handle Assembly........................................................................................ 24-25 Hydraulic Assembly .......................................................................... 26-27 Hydraulic Pump Assembly ................................................................ 28-29 Engine Deck Wire Harness-Kohler (Single Cyl.) & 17KA................... 30 Engine Deck Wire Harness- Kohler Command V-Twin...................... 30 Handle Wire Harness-Electric Start......................................................... 31 Wire Harness W/Relay............................................................................... 31 Engine Deck Wire Harness-14 Kawasaki............................................... 32 Handle Wire Harness-Manual Start......................................................... 32 Replacement Decals.................................................................................. 33-35 Warranty Statement...............................................................Inside Back Cover II INTRODUCTION SIGNAL WORDS Your mower was built to the highest standards in the industry. However, the prolonged life and maximum efficiency of your mower depends on you following the operating, maintenance and adjustment instructions in this manual. This symbol means “Attention! Become Alert! Your Safety is Involved!" The symbol is used with the following signal words to attract your attention to safety messages found on the decals and throughout this manual. The message that follows the symbol contains important information about safety. To avoid injury and possible death, carefully read the message! Be sure to fully understand the causes of possible injury or death. We encourage you to contact your dealer for repairs. All Scag dealers are informed of the latest methods to service this equipment and provide prompt and efficient service in the field or at their service shop. They carry a full line of Scag service parts. A replacement Operator's Manual is available from your Scag Servicing Dealer or by contacting Scag Power Equipment, Service Department, at P.O. Box 152, Mayville, WI 53050. Please indicate the complete model and serial number of your Scag product. Signal Word: It is a distinctive word on safety decals and throughout this manual that alerts the viewer to the existence and relative degree of the hazard. USE OF OTHER THAN ORIGINAL SCAG REPLACEMENT PARTS WILL VOID THE WARRANTY. The “Right” and “Left”, “Front” and “Rear” of the machine are referenced from the operator’s perspective when in the normal operating position and facing the forward travel direction. The signal word “DANGER” denotes that an extremely hazardous situation exists on or near the machine that could result in high probability of death or irreparable injury if proper precautions are not taken. GENERAL SAFETY INSTRUCTIONS WARNING: READ THIS OPERATOR'S MANUAL and instructions furnished with attachments. The signal word “WARNING” denotes that a hazard exists on or near the machine that can result in injury or death if proper precautions are not taken. Perform only those maintenance procedures described in this manual. If major repairs are ever needed or assistance is desired, contact an Authorized Scag Dealer. To ensure optimum performance and safety, always purchase genuine SCAG replacement parts and accessories. CAUTION: The signal word “CAUTION” is a reminder of safety practices on or near the machine that could result in personal injury if proper precautions are not taken. Your safety and the safety of others depends significantly upon your knowledge and understanding of all correct operating practices and procedures of this machine. 1 BEFORE OPERATING WHILE OPERA TING OPERATING 1. Know the controls and how to stop quickly. 1. Start the engine when the neutral latches are in the neutral lock position, the cutter blades are disengaged, the parking brake is on and the speed adjustment lever is in the neutral position. 2. Do not allow children to operate the machine. Do not allow adults to operate the machine without proper instruction. 2. Do not run the engine in a confined area without adequate ventilation. Exhaust fumes are hazardous and could possibly be deadly. 3. Remove all debris or other objects that might be picked up and thrown by the cutter blades. Keep all bystanders away from the mowing area. 3. Using the machine demands attention. To prevent loss of control: A. Mow only in daylight or when there is good artificial light. B. Watch for holes or other hidden hazards. C. Do not drive close to a drop-off, ditch, creek bank, or other hazard. D. Reduce speed when making sharp turns and when turning on hillsides. E. Always be sure of your footing. Keep a firm hold on the handles and walk---never run. F. Do not operate where conditions are slippery. 4. Keep all shields, safety devices, and decals in place. If a shield, safety device or decal is defective or damaged, repair or replace it before operating. Also, check all nuts, bolts and screws for proper tightness, to assure the machine is in safe operating condition. 5. Do not operate the machine while wearing sandals, tennis shoes, sneakers or shorts. Also, do not wear loose fitting clothing which could get caught in moving parts. Always wear long pants and substantial shoes. Wearing safety glasses and safety shoes is advisable and required by some local ordinances and insurance regulations. 4. The discharge chute must always be installed and in the down position on the side discharge cutter deck except when the Scag optional grass catcher or mulching plate are properly installed. If the discharge area should plug, shut the engine off and wait for all movement to stop before removing the obstruction. 6. Fill the fuel tank with clean, fresh gasoline, with a minimum octane rating of 87. Avoid spilling gasoline. Gasoline is highly flammable, handle it carefully. A. Use an approved gasoline container. B. Do not fill the tank while the engine is hot or running. C. Do not smoke while handling gasoline. D. Fill the fuel tank outdoors and up to approximately 1" (25 mm) below the bottom of the filler neck. E. Wipe up any spilled gasoline. 5. Disengage the blades and wait for them to stop before crossing gravel drives, walks or roads. 6. Shut the engine off and wait until the blades come to a complete stop before removing the grass catcher container. 7. Never raise the cutter deck while the blades are rotating. 7. Before attempting to start the engine, move the speed adjustment lever into the neutral position, move the blade engagement switch to the OFF position, apply the parking brake, and move the neutral latches to neutral. 8. Always park the mower and/or start the engine on a level surface. Apply the parking brake to prevent the mower from moving when you are not in the operator’s position. 2 14. Use only Scag approved riding attachments. 9. If the cutting blades should strike a solid object or the equipment should start to vibrate abnormally, stop the engine, disconnect the spark plug wire, and check immediately for the cause. Vibration is generally a warning of trouble. Check the machine for damaged or defective parts. Repair any damage before starting the engine or operating the cutter deck. Be sure the blades are in good condition and the blade bolts are tight. Scag Approved Riding Attachments: RS-ZT Using unapproved attachments, (especially "stand-up" riding attachments) may be hazardous. MAINTENANCE AND STORAGE 1. Disconnect the spark plug wire from the spark plug to prevent accidental starting of the engine when servicing, adjusting or storing the machine. 10. Reduce speed and exercise extreme caution on slopes and in sharp turns to prevent tipping or loss of control. Be especially cautious when changing directions on slopes. 2. If the mower must be tipped to perform maintenance or adjustment, remove the battery, drain the gasoline from the fuel tank and the oil from the crankcase. WARNING: DO NOT operate on steep slopes. To check a slope, attempt to back up it (with the cutter deck down). If the machine can back up the slope without the wheels slipping, reduce speed and use extreme caution. ALWAYS FOLLOW OSHA APPROVED OPERATION. 3. To reduce potential fire hazard, keep the engine free of excessive grease, grass, leaves and accumulations of dirt. 4. Be sure the machine is in safe operating condition by keeping nuts, bolts, and screws tight. Check the blade mounting bolts and nuts frequently to be sure they are tightened. 11. Do not touch the engine or muffler while the engine is running or soon after it is stopped. These areas could be hot enough to cause a burn. 5. If the engine must be running to perform a maintenance adjustment, keep hands, feet, clothing and other parts of the body away from the cutter deck blades and other moving parts. 12. Before leaving the operator’s position or leaving the mower unattended, move the speed adjustment lever into the neutral position, place the neutral latches in the neutral lock position, apply the parking brake, and move the blade engagement switch to OFF. Shut the engine OFF and remove the key. 6. Do not overspeed the engine by changing governor settings. To be sure of safety and accuracy, have an authorized dealer check maximum engine speed with a tachometer. 7. The engine must be shut off before checking the oil or adding oil to the crankcase. 13. Do not pass or stand on the grass discharge side of any mower with the engine running. Stop operation when another person approaches. 8. Allow the engine to cool before storing the mower in any enclosure such as a garage or storage shed. Make sure the fuel tank is empty if the machine is to be stored in excess of 30 days. Do not store the mower near any open flame or where gasoline fumes may be ignited by a spark. WARNING FALLING HAZARD USE ONLY SCAG APPROVED RIDING ATTACHMENTS SEE OPERATOR'S MANUAL 481109 3 9. Always store gasoline in a safety-approved, red container. MOWER OPERATION 1. Read and understand the safety instructions before attempting to operate this machine. 10. Be careful when servicing the battery as it contains acid, which is corrosive and could cause burns to skin and clothing. 2. Before starting the engine: * Check the oil level in the engine and the hydraulic reservoir. * Fill the fuel tank with clean, fresh, leadfree gasoline. * Open the fuel valve on the bottom of the fuel tank. 11. Batteries release explosive gases when being charged or discharged. Keep batteries away from any source of sparks and/or flame. 12. Make sure all hydraulic connections are tight and all hydraulic hoses and lines are in good condition before starting the machine. -NOTEUse gasoline with an octane rating no less than 87. 13. Hydraulic fluid is under high pressure. If you need service on your hydraulic system, please see your authorized Scag dealer. * The speed adjustment lever must be in NEUTRAL. * The blade clutch switch must be in the OFF position. * The neutral latches must be in the neutral lock position. * The key switch must be on. * The parking brake must be on. INITIAL RUN-IN PROCEDURES (FIRST DAY OF USE OR APPROXIMATELY 10 HOURS) 1. Check the belts for proper tension at 2, 4 and 8 hours. Adjust as needed. 3. Start the engine: 2. Check the steering control rods and the speed control for neutral adjustment. (See Adjust ments, page 6-8) * Choke as required. If the engine is cold, pull the choke knob out. When the engine starts, slowly push the choke in. If the engine stalls, repeat the above operation. When the engine is warm, choking may not be necessary. 3. Check the tires for proper pressure. Caster Wheels 25 psi. Drive Wheels 15 psi. 4. Check for loose hardware. Tighten as needed. 4. Engage the cutter blades by pulling the blade clutch switch into the ON position. Push the switch to the OFF position to disengage the cutter blades. 5. Check the safety switches for proper adjustment: * The engine should crank and start if the machine is in neutral, the PTO engagement switch is OFF and the parking brake is ON. 6. Apply lubricant to all the grease fittings. Lubricant was applied at the factory. This is just a precautionary check to make sure that all the fittings have been lubricated. PULL UP TO ENGAGE PUSH DOWN TO DISENGAGE 390S0138 4 -NOTEWhen PTO is engaged or (possibly) disengaged, a squealing sound from the underside of the machine is normal. It is caused by the electric clutch plates meshing as the mower comes up to speed. For best equipment life, engage the clutch with the engine at 1/2 throttle, not under full load. WARNING: If you are not familiar with the operation of the hydrostatic drive and zero turn feature, practice turning and maneuvering with the hand controls before engaging the blades. Dump Valve Levers (normal position) Figure 1. Dump Valves SGB112 CUTTER DECK BEL T ADJUSTMENTS BELT 5. Release the parking brake. Move the speed adjustment lever to the desired mowing speed. -NOTEThe hydro drive belt is spring loaded and does not require adjustment. -NOTETop speed is suggested only for transport! 6. While squeezing the steering brake levers with both hands, release both neutral latches. 1. Remove the belt cover. 7. When the steering brake levers are released, the machine will travel straight. To make a right turn, squeeze the RH lever. To turn left, squeeze the LH lever. 2. Adjust the cutter deck drive belt using a belt tension gauge. Adjust the belt so that the belt moves 1/2" with 10 pounds of pressure. Adjust the tension by tightening or loosening the J-bolt nut. (See figure 2) END OF L-SHAPED BRACKET 8. TO STOP, squeeze both levers, lock the neutral latches, and move the speed adjustment lever to neutral. BELT NUT 9. To move the machine in reverse, squeeze up on both steering control levers. "J" BOLT ire pressure canWASHER be adjusted for 10. To "freewheel" or move the machine around without the engine running, turn the dump valve levers located at the back of the pumps to the "freewheel" positions (see Figure 1). To operate the machine, the dump valve levers must be returned to the closed positions. CUTTER DECK DRIVE BELT TENSION ALIGNMENT IDLER - L.H. SC400G Figure 2. Deck Drive Belt Adjustment 5 LOW CUT (1 3/4"- 3") -NOTEDue to initial belt stretch and to prevent the belt from slipping, check this adjustment after the first 2 hours, 4 hours and 8 hours of operation. MID RANGE (2 1/2"- 3 3/4") 3. Adjust the RH blade drive belt using a belt tension gauge. Adjust the belt so that the belt moves 1/2" with 10 pounds of pressure. Adjust the tension by tightening or loosening the J-bolt nut (See figure 3). HIGH CUT (3 1/4"- 4 1/2") 4. Replace the belt cover. Nut CUTTER DECK HEIGHT ADJUSTMENT Washer SC405G Figure 4. Cutting Height Adjustment Deck Caster spacers also can be repositioned to change cutting heights and to change the pitch of the deck. (See figure 5) "J" Bolt PIN SPACERS Belt Figure 3. Cutter Deck Belt Adjustment R.H. CUTTER DECK ADJUSTMENTS Due to the many cutting conditions that exist, it is difficult to suggest a cutter deck setting that will work for every lawn. There are two adjustments that can be made on these decks, pitch and height. PITCH is the angle of the blades (comparing front to rear). A 1/4" downward pitch (front of deck down) is recommended for best cutting performance. HEIGHT is the nominal distance the blade is off of the ground. This measurement is made with the blades pointed side to side and distance is measured between cutting tip and ground. (Also see Blade Height Adjustment) Changes to the cutting height can be achieved by repositioning the cutter deck. (This adjustment will also effect the pitch of the deck). There are three available positions (see figure 4). REPOSITIONING SPACERS SC406G99 Figure 5. Caster Wheel Spacers BLADE HEIGHT ADJUSTMENT Adjusting the blade height can be done by moving any number of the five smaller 1/4" spacers on the blade mounting bolts to the top of the spindle shaft or below the spindle shaft. -NOTEAll blades should be positioned equally. For best cut and discharge, a minimum of three spacers should be installed between the blade and the spindle (See figure 6). 6 NEUTRAL ADJUSTMENT -NOTENeutral has been set by your Scag dealer at the time of setup and normally does not need to be adjusted. If, however, you find that the neutral has come out of adjustment follow the procedure below. 1. Raise the drive wheels off the ground and block the caster wheels. 2. Make sure the speed control lever is in neutral, the steering control levers are in the neutral latch position, and the parking brake is on. Start the engine. 3. Release the parking brake an note if the tires are rotating. 4. Starting on the left side of the machine, rotate the tracking adjustment knob counter clockwise just until the LH wheel starts to creep forward. Make a note of the position of the adjusting knob (see Figure 8). SC407G Figure 6. Blade Spacers CUTTER BLADES 5. Turn the adjusting knob clockwise just until the wheel turns rearward. Make a note of the position of the adjusting knob. To adjust neutral, split the difference between the two noted positions of the adjusting knob. Do not sharpen beyond 1/3 of the width of the blade. (See figure 7) -NOTEDress the blade with a file. Using a wheel grinder may burn the blade. Check the balance of the blade. If blades are out of balance, vibration and premature wear of spindle assembly can occur. See your authorized Scag dealer for blade balancing or special tools, if you choose to balance your own blades. 6. Turn the engine off. TRACKING ADJUSTMENT SEE OPERATOR'S MANUAL ANGLE BLADE BACK DO NOT CUT IN FAST 481878 X 30 SLOW X MUST NOT EXCEED 1/3 BLADE WIDTH Figure 8. Neutral Adjustment SC4O8G Figure 7. Blade Sharpening 7 2. Squeeze the steering control levers and release the neutral latch. Slowly release the steering control levers, allowing the machine to move forward. STEERING CONTROL ROD ADJUSTMENT -NOTEThis adjustment is made to allow the steering control levers to be moved out of the neutral latch without engaging reverse. 3. If the machine pulls to one side, turn the tracking adjustment knob on the slower side counter clockwise until the machine tracks straight (see Figure 6). Before making this adjustment be sure that the speed control bearing is just touching the speed control cam and that the bellcrank bearing is resting in the center groove of the neutral cam. 4. Bring the steering control levers back to the neutral lock position and check to see that the machine does not creep forward on the adjusted wheel. 1. Remove the speed control spring. Remove the steering control rod swivel hair pin. Check the location of the swivel in the slotted hole in the bell crank . 5. If the machine creeps in neutral you have moved out of the neutral band and will have to turn the tracking adjustment knob clockwise until the machine does not creep. 2. Turn the swivel joint on the steering control rods until the swivel joint is centered in the slot in the bellcrank. 6. Repeat steps 1 and 2. If the machine pulls to one side, turn the tracking adjustment knob on the faster side clockwise until the machine tracks straight. AD TRA JU CK ST IN E O MAPER ME G NU AT NT A O SE FA S T 8. If tracking cannot be achieved, contact your Scag servicing dealer. L R'S SL OW 48 18 78 TRACKING ADJUSTMENT Center of Slot SEE OPERATOR'S MANUAL FAST SLOW 481878 390s0198 Figure 6. Tracking Adjustment Figure 5. Control Rod Adjustment PARKING BRAKE 3. Reinstall the speed control spring onto the swivel. Install the hair pin onto the swivel. 1. Adjust the parking brake so that when the brake hand lever is against the stop on the handle bar, the brake levers on the brake shaft weldment are against the stops on the engine deck. TRACKING ADJUSTMENT -NOTEBefore proceeding with this adjustment, be sure that the tire pressures are correct. (see page 4) and that the neutral adjustment and the steering control rod adjustment have been completed. CAUTION: Adjust the brake only enough to hold the machine. Excessive force may cause damage to the machine or brake components. 1. With the machine on a flat level surface, start the engine and place the speed adjustment lever into the speed that will most often be used. 2. Adjust the brake actuator rod on either side of the machine to obtain proper brake adjustment. 8 LUBRICA TION & MAINTENANCE LUBRICATION BREAK-IN + Grease spindle until grease comes out the relief valve Compatible Greases: Lidok EP #2 (found at industrial shops) Ronex MP (Exxon service stations) 40 HOURS (WEEKLY) Shell Alvania (Shell service stations) Mobilux #2 (Mobil service stations) 100 HOURS (BIWEEKLY) Super Lub M EP #2 (Conoco service stations) 8 HOURS (DAILY) 500 HRS OR ANNUALLY COMMENTS PROCEDURE X X X X X X X X X X X X X X X X X X X X X X Check all hardware for proper tightness Change engine oil and filter at 5 hours Check engine oil Remove debris from under belt cover Sharpen cutter blades Grease spindle bearings Clean air filter Check belt tension Check tire pressure Check battery level Replace air filter Grease caster wheel bearings Grease caster wheel pivot shafts Grease idler pulley bracket on cutter deck Change hydrostatic oil filter Change engine oil and filter Grease idler arm pivots Grease brake hand lever Grease brake actuator levers Check all hardware for proper tightness Adjust air gap on electric clutch Drain hydraulic system and replace oil Do not over fill More often if needed More often if needed + US Lithium MP White Grease 2125 More often if needed Adjust as needed Add or adjust as required Adjust as needed More often if needed Chassis grease Chassis grease Chassis grease Clean area before removing the filter See engine manufacturer information Chassis grease Chassis grease Chassis grease Contact your Scag dealer for information about making this adjustment. 9 TROUBLESHOOTING CUTTING CONDITIONS CAUSE CONDITION Stringers - Occasional Blades of Uncut Grass Width of Deck CURE Low engine RPM Run engine at full 3600 RPM Ground speed too fast Slow speed to adjust for conditions Wet grass Cut grass after it has dried out Dull blades, incorrect sharpening Sharpen blades Deck plugged, grass accumulation Clean underside of deck Belts slipping Adjust belt tensions Dull, worn blades Sharpen blades Incorrect blade sharpening Sharpen blades Low engine RPM Run engine at full 3600 RPM Belt slipping Adjust belt tension Deck plugged, grass accumulation Clean underside of deck Ground speed too fast Slow speed to adjust for conditions Wet grass Cut grass after it has dried out Bent blades Replace blades Not enough overlapping between rows Increase the overlap of each pass SGB020 Streaking - Strips of Uncut Grass in Cutting Path Width of Deck SGB018 Streaking - Strips of Uncut Grass Between Cutting Paths Width of Deck SGB019 Width of Deck 10 TROUBLESHOOTING CAUSE CONDITION Uneven Cut on Flat Ground - Wavy High-Low Appearance, Scalloped Cut, or Rough Contour CURE Lift worn off of blade Replace blade Blade upside down Mount with cutting edge toward ground Deck plugged, grass accumulation Clean underside of deck Too much blade angle (deck pitch) Adjust pitch and level Deck mounted improperly See your authorized SCAG dealer Bent spindle area See your authorized SCAG dealer Dull blade Sharpen blade Uneven ground May need to reduce ground speed, raise cutting height, and/or change direction of cut Tire pressures not equal Check and adjust tire pressure Wheels uneven Check and adjust tire pressure Deck mounted incorrectly See your authorized SCAG dealer Width of Deck SGB020 Uneven Cut on Uneven Ground Wavy Appearance, High-Low Scalloped Cut, or Rough Contour Width of Deck SGB021 Sloping Ridge Across Width of Cutting Path Width of Deck SGB023 11 TROUBLESHOOTING CAUSE CONDITION Scalping - Blades Hitting Dirt or Cutting Very Close to the Ground Width of Deck CURE Low tire pressures Check and adjust pressures Ground speed too fast Slow speed to adjust for conditions Cutting too low May need to reduce ground speed, raise cutting height, change direction of cut, and/or change pitch and level Rough terrain May need to reduce ground speed, raise cutting height, and/or change direction of cut Ground speed too fast Slow speed to adjust for conditions Wet grass Cut grass after it has dried out Blades not mounted evenly Adjust pitch and level Bent blade Replace blade Internal spindle failure See your authorized SCAG dealer Mounting of spindle incorrect See your authorized SCAG dealer Bent spindle mounting area See your authorized SCAG dealer Internal spindle failure See your authorized SCAG dealer Bent deck housing See your authorized SCAG dealer SGB022 Step Cut Ridge in Center of Cutting Path Width of Deck SGB024 Slope Cut - Sloping Ridges Across Width of Cutting Path Width of Deck SGB025 12 TECHNICAL SPECIFICATIONS ENGINES General Type: Brand: Models: Horsepower: Type: Displacement: Cylinders: Governor: Exhaust Group: Fuel Pump Group: Oil Pump Group: Valve Group: Starter/Electrical: Charging System: Heavy duty industrial/commercial Kohler, Kawasaki, Kohler CV15T, Kaw. FC420V (14HP), FH500V (17HP), Kohler 15HP; Kaw. 14HP; Kaw. 17HP 4 cycle gas, vertical shaft engines Kohler: 15HP = 426cc Kawasaki: 14HP = 423cc, 17HP = 494cc Varied - see manufacturer's specifications Mechanical type governor with variable speed control set at 3600 rpm (+75 rpm), idle set at 1200 rpm (+75 rpm) Single exhaust canister muffler Varied - See manufacturer's specifications Varied - See manufacturer's specifications Varied - See manufacturer's specifications Electronic Ignition with recoil starter or 12 volt battery with alternator, solid state ignition with key start 15 amp ENGINE DECK Thickness: Fuel Tank: Drive Wheels/Tires: Brakes: Axles: Handle Bars: 7 gauge steel 5 gallon (19.0 litres) seamless polyethylene 16x6.50-8 four-ply pneumatic tubeless, radius edge Dynamic braking through hydro drive system 1" tapered 1-1/4" diameter DRIVE SYSTEM Type: Hydro Pumps: Drive Wheel Motors: Hydro Fluid Cooling Group: Steering / Travel Control:: Parking Brakes: Dump Valves: Axles: Wire Harness: Safety Group: Forward Speed Range: Reverse Speed Range: Hydro drive with two variable displacement pumps and two cast-iron high torque motors Two Hydro-Gear Model BDP 10L pumps with dump valves for movement without running the engine Two 12 cu. inch cast-iron high torque motors 4qt. capacity cooling radiator, uses, SAE 20W50 fluid and 10 micron filter Independent handle controls for each wheel, squeeze to move from forward to neutral to reverse, neutral lock lever, speed range controlled with single lever (patented design), in-field tracking adjustment with no tools necessary 7.5" drum, band brake, one on each wheel Allows for movement without engine running 1" tapered motor shafts 14 gauge wire Handle actuated operator presence system (patented design), blade / clutch and transmission interlock to engine kill 0 to 7.4 mph 0 to 3.0 mph Date of Issue: June 18, 1999 Specifications Subject to Change Without Notice 13 TECHNICAL SPECIFICATIONS CUTTER DECKS (CON'T) SWM 36, SWM 48, SWM 48 Advantage, SWM 52, SWM 52 Advantage, SWM 61, SWM 72 Out-front design with anti-scalp rollers SWM36,48, 48A: 7-gauge steel with 7-gauge (3/16") steel skirt SWM52,52A, 61,72:10-gauge steel with 7-gauge (3/16") steel skirt 35.5" (90.2 cm), 48.0 (122.0 cm), 52.0 " (132.0 cm), 61.0 " (155.0 cm), 71.5" (181.6 cm) Adjustable from 1-3/4" to 4-1/4" in 1/4" increments Marbane®, .197 thickness SWM 36: Two (2) 18"; SWM 48: Three (3) 16.5" SWM 52: Three (3) 18"; SWM 61: Three (3) 21" SM72: Three (3) 24" blades Electric blade brake clutch with instrument panel switch Extra wide 11.5", 13.75 " discharge opening with hinged chute 9.4 x 3.5 smooth tread flotation, inner tubes, split rims, roller bearings, with quick pin removal Cast housing, taper roller bearing, low maintenance with top access grease fitting and grease overfill relief poppet Cast-iron with easily removed taper hubs 5" diameter pulley, welded and riveted construction, 1-3/8" O.D. Bearing Heavy duty idler arm of 1/4" channel steel B-section with Kevlar cord Type: Construction: Cutting Width: Cutting Height Adjustment: Cutter Blades: Blade Engagement: Discharge Opening: Caster Wheels: Spindles: Spindle Pulleys: Idler Pulley: Idler Arm: Cutter Deck Belts: ADDITIONAL SPECIFICATIONS OPTIONAL ITEMS/ATTACHMENTS Fabric Grass Catcher: Metal Grass Catcher: GC-F4 Grass Catcher with 4 cubic ft. capacity GC-4D Grass Catcher with 4 cubic ft. capacity and rope pull dump or pick-up and dump RS-ZT Steerable Sulky with padded seat and full articulation for zero-radius turning Steel plate fits over discharge opening. No blade change or or removal required. Installs and removes in the field. Steerable Sulky: Mulching Plate: APPROXIMATE DIMENSIONS Length: Length with Grass Catcher: Tracking Width: Width: Width (with discharge chute up): With with grass catcher: Height: Height with grass catcher: Weight Weight with grass catcher: Turning Radius: SWM36 SWM48 SWM48A SWM52 74.0" 74.0" 37.0" 54.5" 37.5" 55.0" 43" 43" 515 lbs. 555 lbs. Zero 74.0" 74.0" 42.0" 59.0" 49.0" 65.0" 43" 43" 555 lbs. 595 lbs. Zero 76" 76" 42.0" 59.0" 49.0" 65.0" 43" 43" 560 lbs. 600 lbs. Zero 76" 76" 42.0" 62" 52" 78" 43" 43" 605 lbs. 645 lbs. Zero Date of Issue: June 18,1999 Specifications Subject To Change Without Notice 14 SWM52A 78" 78" 42.0" 62" 52" 78" 43" 43" 610 lbs. 650 lbs. Zero SWM61 SWM72 76.0" 76.0" 42.0" 70.0" 63.0" 80.0" 43" 43" 625 lbs. 665lbs. Zero 76.0" 76.0" 42.0" 81.0" 74.0" 91.0" 43" 43" 695lbs. 730 lbs. Zero NOTES 15 32" & 36" CUTTER DECKS 41 69 9 45 47 43 11 41 69 44 44 45 68 61 59 11 46 46A 43 58 57 22 42 53 A 41 39 39A 40 42 48 7 60 58 54 14 55 50 13 56 37 18 49 52 38 36 51 A 49 2 19 37 20 21 14 55 35 40 22 21 8 20 23 24 1 1A 14 25 62 27 28 26 35 10 5 66 29 22 6 34 32 31 33 4 11 3 12 30 31 11 64 5 15 15A 16 63 67 17 SW-SWZ99CD36 16 65 36" CUTTER DECKS Ref. Part No. Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 15A 16 17 18 19 20 21 22 23 24 25 26 27 28 29 NS 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 461131 46631 43312 48307-08 481022 43294 04001-108 43298 04001-77 04063-08 43278 04001-10 481050 04019-03 481707 481711 04040-10 04001-41 46079 04066-01 43037-01 48100-01 48114-04 46082 45006 43022 04001-37 04021-07 48307 48307-02 48006-03 48307-04 48006-07 48006-06 48114-03 48006-05 04017-16 461054 04021-10 04001-09 46797 04041-07 04029-03 48924 48926 04001-01 Description Cutter Deck (Includes Decals) Cutter Spindle Assy. Spacer, Outside Tapered Nut, 5/16-24 Tapered Bearing (Two) Spindle Housing Bolt, 5/16-18 x 4-1/4" Hex Head Spindle Shaft Bolt, 3/8-16 x 3-1/2" Hex Head Key, 1/4 x 1/4 x 2" Spacer, Cutter Blade - Small Bolt,5/16-18 x 1-1/4" Hex Head Spring, Chutte Return Nut 5/16-18 Serrated Flange Cutter Blade, 18" Cutter Blade, 18 Hi Lift Flatwasher, 5/8 W Hex Hd. Bolt, 5/8-11 x 9-1/2" Caster Assembly (Inc.19-28) Quick Pin Spacer, Caster Yoke, 1/2" long Bronze Bearing Grease Fitting Support Assembly (Inc. 21-23) Caster Yoke Sleeve, Caster Wheel Bearing Hex Hd. Bolt, 1/2-13 x 5-1/2" Elastic Stop Nut, 1/2-13 Wheel Assy. (Inc.4, 29-34) Tire only, Caster Wheel Inner Tube only Rim Pair, Caster Wheel Retainer, Bearing, Caster Wheel Roller Bearing, Caster Wheel Grease Fitting, 45 degree 1/4-28 Hub Assembly Cpscrw,5/16-18 x 3/4" Ser.Flg. Hex Head Discharge Chute Hex Nut, 5/16-18 Elastic Stop Hex Hd Bolt, 5/16-18 x 1" Belt Cover Assy (Includes Decal) Flat Washer, 3/8" Special Wing Nut, 3/8-16 Pulley Tapered Hub Hex Hd. Bolt, 1/4-20 x 3/4" Ref. Part No. Number 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 69 04020-09 48204 43077 04021-05 04019-04 04004-02 04017-42 04019-05 43277 04041-12 04021-09 45423 46748 48100-02 04050-05 44078 48269 481024 43297 43296 481035 48677 481025 48098 04029-04 04029-04 Description Hex Nut, 5/8-11 Belt, Blade Drive Spacer Hex Nut, 3/8-16 Center Locknut Nut, 3/8-16 Serrated Flange Support, Belt Cover Cpscrw, 7/16-14 x 1"Ser.Flg. HH Nut, 7/16-14 Serrated Flange Spacer, J-Hook Washer, 3/8 x 1-1/2 x 16 GA Elastic Stop Nut, 3/8-16 Idler Pivot Idler Arm Assy. (Inc. 22 & 58) Bronze Bearing Retaining Ring, 1-1/8" Ext. ”E” J-Hook Idler Pulley, Belt Clutch Seal, Cutter Spindle Spindle Bushing Spacer, Inside Nut, Relief Fitting, Cutter Spindle Seal, Cutter Spindle Spindle Shield Wing Nut, 3/8-16 (Small) Top Side Wing Nut, 3/8-16 (Small) RH Side * Common hardware which should be purchased locally. All bolts are Grade 5 plated, all other fasteners zinc plated. 17 48, 48A, 52, 52A, 61,72" & 72" CUTTER DECKS 48", 52", 61", & CUTTER DECKS 41 73 22 59 56, 56A 61 51 44 45 40 45 44 11 43 43 11 48 45 7 51 44 58 60 47 4 39 40 11 41 46 46A 46B 41 62, 62A 63 43 64 65 49 82 61 14 76 78 42 42A 42B 52 13 40 63 9 37 74 77 67 7 38 36 36A 18 50 A 55 54 57 51 40 19 37 20 68 77 35 A 35 14 64 14 51 75 21 50 7 21 14 20 23 24 8 35 2 25 27 66 1 28 80 26 79 10 5 53 69 7 6 29 34 11 32 31 33 83 11 30 70 12 3 5 15 15A 31 16 71 81 17 SW-SWZ99CD48" 18 72 48, 48A, 52, 52A, 61, & 72" CUTTER DECKS Ref. Part No. No. Description 1 1 1 1 1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 15 15 15 15A 15A 15A 16 17 18 19 20 21 22 23 24 25 26 27 28 29 NS 30 31 32 33 34 35 36 36A 37 38 39 39 39 39 39 40 41 42 42A Cutter Deck (Includes decals) x Cutter Deck Adv. (Inc. decals) x Cutter Deck (Includes decals) Cutter Deck Adv. (Inc. decals) Cutter Deck (Includes decals) Cutter Deck (Includes decals) Spindle Assembly x Spacer, Inside x Pulley x Tapered Bearing (Two) x Spindle Housing x Grease Fitting Str. 5/16 x Spindle Shaft, Tapered Brng x Idler Pivot x Key, 1/4 x 1/4 x 2" x Spacer, Cutter Blade - Small x Bolt, 5/16-18 x 1-1/4" Hex Head x Bolt, 5/16-18 x 4-1/4" Hex Head x Serrated Flange Nut, 5/16-18 x Cutter Blade 16-1/2" x Cutter Blade 18" Cutter Blade 21" Cutter Blade 24" Cutter Blade 16-1/2 Hi Lift x Cutter Blade 18 Hi Lift Cutter Blade 21 Hi Lift Flatwasher,5/8" (.688 x 1.75 x .134)x Hex Head Bolt, 5/8-11 x 9-1/2" x Caster Assembly, (incl.19-28 & 7) x Quick Pin x Spacer, Caster Yoke, 1/2" thick x Bronze Bearing x Spindle Shield x Support Assembly, (incl. 21-23) x Caster Yoke x Sleeve, Caster Wheel Bearing x Hex Hd Bolt, 1/2-13 x 5-1/2" x Elastic Stop Nut, 1/2-13 x Wheel Assy. (incl. 29-34,81) x Tire only, Caster Wheel x Inner Tube only, Caster Wheel x Rim Pair, Caster Wheel x Bearing Retainer, Caster Wheel x Roller Bearing, Caster Wheel x Grease Fitting 45 deg., 1/4-28 x Hub Assembly, (incl. bolts) x Capscrew, 5/16-18 x 3/4" x Discharge Chute Discharge Chute x Nut, 5/16-18 Elastic Elastic Stop x Bolt, 5/16-18 x 1" Hex Head x Belt Cover (Includes decals) x Belt Cover (Includes decals) 17KA x Belt Cover (Includes decals) Belt Cover (Includes decals) Belt Cover (Includes decals) Flat Washer, 3/8" Special x Wing Nut, 3/8-16 (Large) x Pulley x Pulley 461132 461231 461264 461273 461138 46608 46631 43296 48924 481022 43294 48114-04 43298 45037 04063-08 43278 04001-10 04001-108 04019-03 48110 48108 48111 48112 48184 48185 48304 04040-10 04001-41 46079 04066-01 43037-01 48100-01 48098 46082 45006 43022 04001-37 04021-07 48307 48307-02 48006-03 48307-04 48006-07 48006-06 48114-03 48006-05 04017-16 461055 461054 04021-04 04001-09 46798 461095 46804 46805 46848 04041-07 04029-03 48924 48753 Ref. Part No. No. 48 52 61 72 42B 43 44 45 46 46A 46B 47 47 47 47 48 48 48 48 49 50 51 52 53 54 55 56 56A 57 58 59 60 61 62 62A 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x 19 Description 48967 48926 04001-01 04020-09 48923 48940 48966 48087 48285 48265 48295 48089 48286 48088 48296 04021-05 04019-04 04021-09 04004-02 04001-08 04017-42 04019-05 04041-08 04041-08S 44078 48181 04050-02 46081 48100-05 43028 44078 43077 04041-12 04001-46 481024 46748 43277 48677 43312 43297 481035 04029-04 04001-77 45329 48269 48100-02 04050-05 48038 45944 481025 481050 48307-08 48 52 61 72 Pulley Tapered Hub Bolt, 1/4-20 x 3/4" Hex Head Nut, 5/8-11 Hex Pulley, Double Pulley, Double Pulley, Double Belt, RH Blade Drive Belt, RH Blade Drive Belt, RH Blade Drive Belt, RH Blade Drive Belt, Blade Drive Belt, Blade Drive Belt, Blade Drive Belt, Blade Drive Nut, 3/8-16, Nut Centerlock Nut, 3/8-16, Serrated Flange Nut, 3/8-16 Elastic Stop Support, Belt Cover Bolt, 5/16-18 x 1/2" Hex Head Cpscrw,7/16-14 x 1"Ser Flng H Hd Nut, 7/16-14 Serrated Flange Flat Washer 3/4" Special Flat Washer 3/4" Special J-Hook Idler Pulley, “V” Groove Retaining Ring, 3/4" Ext.”E” Idler Arm Assy. (Incl. 7 & 61) Bronze Bearing J-Rod, Idler Pulley J-Rod, Idler Pulley Spacer, J-Rod Washer, 3/8 x 1-1/2 x 16 ga. Bolt, 3/8-16 x 2-1/4" Hex Head Seal, Cutter Spindle Idler Arm Assy (Includes 22&77) Spacer, J-Rod Reiief Fitting, Cutter Spindle Spacer, Outside, Cutter Spindle Spindle Bushing Nut, Cutter Spindle Wing Nut, 3/8-16 (Small) Top Side Bolt, 3/8-16 x 3-1/2" Hex Head Idler Pivot Idler Pulley, Belt Clutch Bronze Bearing Retaining Ring Guide Roller Roller Shaft Seal, Cutter Spindle Spring, Chute Return Nut, 3/8-24 Tapered x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x ENGINE DECK 5 58 7 4 55 6 2 48 7 1 53 51 8 18 16 50 3 17 38 16 10 37 33 61 BLK 60 RED 9 11 45 63 34 34A 32 42 45 11A 56 65 43 15 ELECTRIC 12 START ONLY 12A 14 20 19 57 13 11 59 35 49 38 38 39 47 47A 64 35 23 27 39 41 22 21 54 62 40 45 43 28 44 26 45 43 25 29 24 46 38 43 30 31 030441698 20 ENGINE DECK Ref. Part No. No. Description 1 1 1 1 2 3 4 5 6 7 8 9 10 11 11A 12 12A 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 34A 35 36 37 38 39 40 Engine 14KA Kawasaki Engine 15KH Kohler Engine 17KA Kawasaki Engine 20CVE Kohler Command Retaining Ring, 1/2" Ext. "E" Hex Nut, 1/4-20 Screw, 1/4-20 x 2" Rnd. Hd. Phil. Strap, Fuel Tank Cap, Fuel Tank Pad, Rubber-Fuel Tank - Upper Fuel Tank Assy. (incl. 9, 10) Bushing Valve, Fuel Shut-off Clamp, Fuel Hose Clamp, Fuel Hose, (KA Only) Fuel Hose, 1/4 ID x 20" KA Fuel Hose, 1/4 ID x 23" Cable Tie Fuel Filter Fuel Hose, 7/32 ID x 3-1/2" Capscrew, #10-32 x 1 Soc. Hd. Lever Assy., Pump Control -LH Lever Assy., Pump Control -RH Battery Bolt, 1/4-20 x .50" Nut, 1/4-20 Pad Battery Cover Wing Nut, 1/4-20 Battery Support Pad, Rubber Bolt, 1/4-20 x 6" Carriage Carriage Bolt, 5/16-18 x 2" Carriage Bolt, 5/16-18 x 1" Stiffener Plate, Backing Nut, 1/4-20 Elastic Stop Pad, Rubber-Fuel Tank, Lower Engine Deck, 16" Wide, W/Decls. Engine Deck, 20" Wide, W/Decls. Bolt,1/4-20 x 1-1/4" Hex Head Nut, 1/4-20 Serrated Flange Capscr., 5/16-18 x 1.25 Sr. Flg. Nut, 5/16-18 Serr. Flange Nut, 3/8-16 Serr. Flange Bolt, 3/8-16 x 2-3/4" Hex Head 48842 48844 481066 48971 04050-10 04020-02 04010-10 421239 481603 48292 46846 48309 48308 48059-01 48059-02 48058 48058 48028-05 48057-02 48179 04015-06 46323 46324 48015 04001-44 04020-02 48099 42392 04029-01 45685 48661 04003-01 04003-28 04003-04 422553 422552 04021-08 48205 461269 461270 04003-09 04019-02 04017-18 04019-03 04019-04 04001-22 14KA 15KH 17KA 20CVE x 41 42 43 44 45 46 47 47A 48 49 50 51 52 53 54 54 55 56 57 58 59 60 61 62 63 64 65 x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x Ref. Part No. No. x x x x x x x 21 Description 04001-08 Hex Head Bolt, 5/16-18 x .75" 04040-14 Flat Washer 1/4" 04021-10 Nut, 5/16-18 Elastic Stop 04003-04 Carrage Bolt, 5/16-18 x 1" 48030-09 Clamp 421370 Clutch Bracket 04017-19 Capscr, 5/16-18 x 1.50" Sr. Flg. 04002-01 Metric HH Bolt, M8-1.25 x M30 04031-09 Lock Washer, 5/16 Int. Tooth 04030-03 Lock Washer, 5/16 48257 Pipe Cap 48402-04 Pipe, 4.75" Nipple 04003-09 Carrage Bolt, 1/4-20 x 1-1/4" 481717 Wire Hrns. Adapter, 17KA 45418 Pulley Guard, 16" Frame 45419 Pulley Guard, 20" Frame 45283 Shaft Weldment, RH Pump Cntl. 421390 Bracket, Capacitor 21013-2064 Condenser (order from Kaw. ) 04002-07 Metric H H Bolt, 8-1.25 x 10 21066-2071 Regulator, (order from Kaw.)M 48029-02 Battery Cable, 31.5" Red 48029-14 Battery Cable, 31.5 Black 421703 Battery Box 48126 Rubber Boot 04003-12 Carrage Bolt, 5/16-18 x .75 48030-10 Cable Clamp, .75 ID 14KA 15KH 17KA 20CVE x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x DRIVE AND BRAKE COMPONENTS 1 2 3, 3A 5 4 7 8 9 6 10, 10A 7 A 49 53 51 40 11 43 44 42 41 42 2 47 45 50 52 48 49 4 50 46 7 39 38 1 A 2 11 48 12 36 47 35 37 34 21 20 19 24 24A 13 14 15 18 33 25 26 32 23 17 16 22 27 30 29 28A 28B 28C SWZ99D&BC 31 22 DRIVE AND BRAKE COMPONENTS Ref. Part No. No. 1 2 3 3A 4 5 6 7 8 9 10 10A 11 12 13 14 15 16 17 18 19 20 21 22 23 24 24A 25 26 27 04050-02 04001-19 45842 45854 04062-01 04003-12 44126 04019-04 43415 48114-05 45860 45861 04001-46 481618 48004-04 422214 48679 04028-01 481502 422215 04008-01 46928 481470 04063-07 481416 48553 48587 461073 04041-28 04030-05 Description Retaining Ring, 3/4 Ext. "E" Bolt, 3/8-16 x 1" Hex Head Brake Shaft Assy. Wlmt.Small Brake Shaft Assy. Wlmt.Large Hair Pin Cotter, .094 x 1.62 Carrage Bolt, 5/16-18 x .75" Rod, Brake Lower Nut, 3/8-16 Serr. Flange Bushing, Brake Grease Fitting Brake Actuator Wlmt., LH Brake Actuator Wlmt., RH Bolt, 3/8-16 x 2-1/4" Tire, 16 x 6.50, 4 ply Rim Assy Lock Washer, Wheel Motor Hex Castle Nut, 3/4-28 UNEF Nut, Lug Wheel Assy., (incl. 31,32) Brake Drum 1/2-20 Serrated Bolt Hub, Wheel Brake Band, 7.5" Key, 3/16 X .75 Woodruff Wheel Motor Belt, Pump Drive (Sm Frame) Belt, Pump Drive (Lg Frame) Electric Clutch Flat Washer .469 x 1.75 x .25 Lock Washer, 7/16 14KA 14KH 17KA 20CVE x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x Ref. Part No. No. 28A 28B 29 30 31 32 33 34 35 36 37 38 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 23 Description 04002-05 Hex Head Bolt, M10-1.5 x 65 04001-149 Hex Head Bolt, 7/16-20 x 2.00" 422534 Plate, Backing 48030-09 Clamp 04021-10 Nut, 5/16-18 Elastic Stop 481716 Rubber Pad, Clutch Stop 422533 Retainer, Clutch Stop 04001-12 Hex Head Bolt, 5/16-18 x 1.75" 481665 Pulley, Pump Drive Engine 04001-13 Hex Head Bolt, 5/16-18 x 2.75" 04021-05 Nut, 3/8-16 Center Lock 04041-08 Washer, 3/4-.766 x 1.2 x .06 04041-08S Washer, 3/4-.766 x 1.2 x .035 48100-05 Bushing, 3/4 Sintered 48114-04 Grease Fitting, Str. 1/4-28 48051 Spring, Pump Belt Idler 04019-03 Nut, 5/16-18 Serr. Flange 04063-24 Key, 1/4x1/4x2.75" Clutch Mtg. 04063-01 Key, 1/4x1/4x1.25" Pulley Mtg. 04041-07 Flat Washer, 3/8 48473 Pulley, Idler Pump Drive 48586 Pulley, Pump Shaft 04012-04 Setscrew, 5/16-18 x 3/8" 04030-04 Lockwasher, 3/8 04063-14 Key, 5.0 x 5.0 x 25mm 45212 Pivot, Idler Arm 43032 Swivel Joint 46940 Arm, Idler 14KA 14KH 17KA 20CVE x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x HANDLE ASSEMBLY 89 74 16 11 68 19 15 90 16 76 71 A 8 7 6 25 18 17 A 11 2 12 9 13 31 20 19 5 4 3 1 10 37 78 22 23 24 15 14 26 81 82 42 24 16 21 35 60 11 27 91 34 29 86 3 61 28 66 30 85 3 37 40 38 92 80 34 36 32 102 69 78 79 104 67 61 40 87 93 3 B 72 39 49 48 C 33 40 47 101 37 94 41 100 11 52 84 C 60 58 73 53 46 58 103 83 98 50 97 70 24 37 61 62 57 95 66 38 96 42 51 99 73 10 79 B 88 60 54 77 20 REF. 75 63 66 82 65 59 45 11 88 64 24 92 6 45 43 44 SWZU00HA HANDLE ASSEMBLY Ref. Part No. No. Description 1 1 2 3 4 5 6 7 8 9 10 11 12 13 13A 14 15 16 16A 16A 17 18 18A 19 19A 20 20A 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 39A 40 41 42 43 44 45 46 47 48 Upper Handle Wlmt. W/Decals Upper Handle Wlmt. W/Decals Quadrant, Speed Control Hairpin, .094 x 1.19 Lever, Speed Adjustment Bushing, Speed Adjustment Lever Hex Head Bolt, 3/8-16 x 1-1/2" Ball Plunger Knob, Speed Adjustment Capscrew, 1/4-20 x 3/4" FHHS Nut, 1/4-20 Elastic Stop Nut, 5/16-18 Elastic Stop Screw, #10-32 x 1/2" PW HD Throttle Control Throttle Control Nut, #10-32 Serr. Flange Bushing Handle, Oper. Presence-RH Handle, Oper. Presence-LH (20") Handle, Oper. Presence-LH (16") Switch,Elec.Clutch Eng. (incl.Nut) Wire Harness, Manual Start Wire Harness, Electric Start Key Switch, Manual Srt. (incl. Hdw) Key Switch, Elec. Start (incl. Hdw.) Neutral Latch-RH Neutral Latch-LH Switch, Neutral Interlock Grip Washer, Curved Spring Flat Washer Lock Washer,1/4" Int. Tooth Hex Head Bolt, 5/16-18 x 2" Hex Hd. Bolt, 5/16-18 x 2-1/2" Lever, Steering Control (incl. 29) Grip, Steering Control Rod, Steering Control Spring, Handle Return Capscr., 3/8-16 x 1" Ser. Flange Lock Washer, !/4" Nut, 3/8-16 Serr. Flange Rod Speed Control Bellcrank, Speed Control Setscrew, 1/4-28 x 1/4" Cam, Speed Control (incl. SS) Jackshaft, Speed Control Jackshaft, Speed Control Key, 1/8 x 1/2" Woodruff Nut, 3/8-16 Elastic Stop Pivot, Pump Ctrl. (incl.Bshg & Zrk) Bushing, 1/2" ID Capscrew, 5/16-18 x 1" Serr. Flg. Nut, 5/16-18 Serrated Flange Bar, Speed Control Spacer, Speed Ctrl. Bearing Bearing, Speed Ctrl. Bellcrank 461128 461129 42675 04062-02 45282 43086 04001-20 48493-01 48092 04014-01 04021-08 04021-10 04010-01 481071 48946 04019-01 48312 45572 45571 45573 481687 481680 481681 48609 48798 46942 46941 48717 48159 04032-01 04040-15 04031-08 04001-17 04001-53 46744 48492 44050 48951 04017-27 04030-02 04019-04 44051 45279 04012-02 46335 43166 43155 04063-13 04021-10 46336 48100-04 04017-17 04019-03 42730 43161 48409 14KA 15KH 17KA 20CVE x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x Ref. Part No. No. Description 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 63A 64 64A 65 66 67 68 69 69A 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 Hex Head Bolt, 5/16-18 x 1-3/4" Spring, Return Knob, 5/16-18 Bushing Handle, Neutral Adj Drive Pin, 5/32 x 7/8 Type U HH Bolt,5/16-18 x 3/4" Lock Washer, 5/16 Nut, 5/16-18 Serr. Flange Bearing, Ball Neutral Return Cam, Neutral (incl. grease ftng.) Grease Fitting, 1/4-28 UNF Retaining Ring, 5/8 Ext. "E" Hex Head Bolt, 5/16-18 x 1" Shaft, Pump Control-LH Shaft, Pump Control-RH Bellcrank, Pump Control-LH Bellcrank, Pump Control-RH Retaining Ring, 1/2 Ext. "E" Flat Washer, 15/16x25/64x12 ga Deck, Engine Hex Head Bolt, 5/16-18 x 1-1/4" Choke Control Choke Control Spring, Return Fuse Holder Swivel Joint, Steering Rod Flat Washer (.344 x .688 x .065) Blade Fuse, 20A Nut, #10-32 Elastic Stop Screw, #10-32 x 1-1/2" Phillips Pin, Neutral Lock Swivel Joint Rod, Brake Lever Hex Hd. Bolt, 3/8-16 x 1 3/4 Soc. Hd. Capscrew, #8-32 x 1/2 Nut, 3/8-16 Elastic Stop Washer #8-.170 x .375 x .032 Retaining Ring, 5/8 Ext, "E" Spacer Parking Brake Lever with Grip Switch, Parking Brake Nut, 3/8-24 Bushing, bearing Retainer Bearing, Neutral Lock Grip, Parking Brake Ball Joint, RH Thread Hairpin, .094 x 1.62 Bracket, Choke Mtg. (16" Only) 04001-69 48494-02 481517-02 43308 45292 04065-05 04001-08 04030-03 04019-03 48224 46747 48114-05 04050-01 04001-09 45295 45283 45642 45643 04050-10 04041-07 By Ref. 04001-10 481278 481072 481057 42413 43306 04040-04 48298 04021-01 04010-03 43305 43032 44125 04001-21 04015-13 04021-09 04041-23 04050-01 43212 46954 481476 04020-14 481411 481420 48342 48464 04062-01 481622 14KA 15KH 17KA 20CVE * Common hardware which should be purchased locally. All bolts Grade 5 plated, all other fasteners zinc plated. 25 x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x HYDRAULIC ASSEMBLY 1 2 K B 5 B E 21 13 7 4 4 3 4 29 8 D 12 J 10 19 H J 4 22 D 31 5 13 C 23 18 18A 17 28 24 32 3 20 11 10 30 A 35 10 28 11 H E 6 5 22 35 C A 13 7 4 6 15 4 14 16 10 29 8 28 11 K 19 33 12 28 10 34 11 10 9 F G 26 25 FG 10 19 10 19 21 27 030441798 26 HYDRAULIC ASSEMBLY Ref. Part No. Number Description 1 2 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 18A 19 20 21 22 23 24 25 25 26 27 28 29 30 31 32 33 34 35 Cap, Oil Reservoir Oil Reservoir (small Frame) Oil Reservior (Large Frame) Elbow, 90 deg. Female 1/4 NPT to 1/4 JIC Male Coupling, 7/16-20 SAE Flare Swivel to 1/4" Hose Push On Hose, 1/4" ID - 12" Long (Order By The Inch) Elbow, 90 deg. 7/16-20 JIC to 9/16-18 "O" Ring O-Ring Pump, Hydro-Gear BDP-10L117 Bolt, Carriage, 3/8-16 x 1-1/4" Hose, Pump to Motor O-Ring Elbow, 90 deg., 7/16-20 JIC x 7/16-20 O-Ring Hose, 1/4" ID - 10" Long (Order By The Inch) Oil Filter Base Elbow, 90 deg. Male 3/4-16 JIC to 1/2" Male NPT Spacer, Oil Filter Base (20" Frame) Coupling, 3/4-16 SAE to 1/2" Hose Push On Capscrew, 5/16-18 x .75" (For 16") Serr. Flange Capscrew, 5/16-18 x 2.25" (For 20") Serr. Flange O-Ring Elbow, 90 deg. Male 1/4 NPT to 1/4 Hose Push On Nut, 5/16-18 Serr. Flange Hose, Formed 1/2" ID Coupling, 1/4 straight Male NPT to 1/4 Hose Push On Bolt, 5/16-18 x 3/4" Carriage Engine Deck (16" Wide) W/Decals Engine Deck (20" Wide) W/Decals Nut, 3/8-16 Serr Flange Oil Filter Elbow, 45 Deg.-3/4-16 JIC Male x Male 3/4-16 O-Ring O-Ring Coupling, 3/8 Pipe to 1/2 Push-on T-Fitting, 3/8 NPT Plug, 3/8-18 NPTF Magnetic Screw, 1/4-20 x 2.0" Round Head Phillips Nut, 1/4-20 Elastic Stop Clamp, .87 max dia. 48535 46618 46619 48484-01 48353-02 48482 48350-04 48603-06 48551 04003-11 481265 48603-02 48350-03 48482 48471-02 48489-02 43096 48936-03 04017-16 04017-22 48603-04 48486-01 04019-03 481562 48352-02 04003-12 46946 46947 04019-04 48462-01 48485-01 48603-03 481537-02 48491 48731-01 04010-10 04021-08 48136-05 14KA 15KH x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x 17KA 20CVE * Common hardware which should be purchased locally. All bolts Grade 5 plated, all other fasteners zinc plated. 27 x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x HYDRAULIC PUMP ASSEMBLY 30 26 it e lS u rha K al 25 e Ov 24 23 22 27 28 1 29 19 20 21 17 16 3 15 18 11 2 14 12 13 5 6 7 8 11 10 9 4 SC165G 28 HYDRAULIC PUMP ASSEMBLY Ref. Part No. Number Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Housing Kit (Incl. Housing, Journal Bearing) End Cap Straight Headless Pin Socket Head Screw End Cap Gasket Charge Pump Kit (Incl. Charge Cover, Gerotor Assy., O-Ring) Gerotor Assembly O-Ring Charge Relief Valve Kit Socket Head Screw Check Valve Kit (Incl. Check Plug, Spring, O-Ring, Orifice Check Valve) Bypass Valve Kit (Incl. Bypass Valve, O-Ring, Back-up Ring) Backup Ring Cylinder Block Kit Block Spring Block Thrust Washer Roller Thrust Bearing Swash Plate Trunnion Arm Guide Slot Cradle Bearing Lip Seal Pump Shaft Ball Bearing Retaining Ring Lip Seal Retaining Ring Spacer Shaft Kit (Incl. Pump Shaft, Ball Bearing, Retaining Ring) Overhaul Seal Kit (Incl. Gasket, Trunnion Seal, Input Shaft Seal, Charge Pump O-Ring) HG 2513017 HG 2513016 HG 9004800-2506 HG 9007314-0810 HG 2003067 HG 2513027 HG 50273 HG 9004101-1340 HG 2510064 HG 50095 HG 2510027 HG 2513030 HG 9006110-0120 HG 70079 HG 2003014 HG 2003017 HG 2003044 HG 2003087 HG 2003005 HG 2000015 HG 2003023 HG 9008000-0126 HG 2003020 HG 2003043 HG 2003016 HG 9008000-0128 HG 2003052 HG 2003018 HG 2513038 HG 2513018 * Common hardware which should be purchased locally. All bolts Grade 5 plated, all other fasteners zinc plated. 29 BLADE CLUTCH NEUTRAL INTERLOCK BLACK W/RED STRIPE GROUND ENGINE DECK WIRE HARNESS KOHLER, (SINGLE CYLINDER) & 17 HP Kawasaki PART NO. 481073 BLACK E A BLACK F B G C H D BLUE WHITE WHITE YELLOW WIRE HARNESS ADAPTER - ENGINE INSTRUMENT PANEL HARNESS SWZ99SC421G TRANSMISSION ENGINE DECK WIRE HARNESS KOHLER COMMAND V-TWIN PART NO. 481075 ENGINE GROUND TO ENGINE BLACK W/RED STRIPE RED E A F B G C H D GREEN BLACK BLUE WHITE WHITE YELLOW BLACK ELECTRIC CLUTCH TO INSTRUMENT PANEL CONNECTOR STARTER SOLENOID 30 SC422G HANDLE WIRE HARNESS - ELECTRIC START FUSES PART NO. 481681 YELLOW W/RED STRIPE GREEN YELLOW WHITE WHITE BLACK W/RED STRIPE MOWER ENGAGE SWITCH KEY SWITCH BRAKE SWITCH BLACK BLACK W/RED STRIPE RED GREEN A BLACK B F C G D H E WHITE RED BLACK RED BLUE TO OPERATOR PRESENCE SWITCH YELLOW TO ENGINE DECK WIRE HARNESS BLACK W/RED STRIPE RED W/ YEL STRIPE NEG HOURMETER POS HOURMETER SWZ99-481681 WIRE HARNESS WITH RELAY PART NO. 481275 To Engine Ground RELAY BLACK GREEN To Starter BLUE RED To Blue Wire From Engine SC481275 To Starter Red Battery Cable Post 31 ENGINE DECK WIRE HARNESS KAWASAKI PART NO. 481074 NEUTRAL INTERLOCK BLACK W/RED STRIPE E A BLACK F B BLUE WHITE WHITE YELLOW G C H D REGULATOR RED RED ENGINE BLACK BLADE CLUTCH BLACK INSTRUMENT PANEL HARNESS SWZ99SC417G GROUND BRAKE SWITCH MOWER ENGAGE SWITCH BLACK W/RED STRIPE WHITE KEY SWITCH HANDLE WIRE HARNESS MANUAL START PART NO. 481680 WHITE BLACK W/RED STRIPE BLACK BLACK BLUE WHITE BLACK W/RED STRIPE TO OPERATOR PRESENCE SWITCH NEG HOURMETER YELLOW BLACK YELLOW A E B F C G D H TO ENGINE DECK WIRE HARNESS POS HOURMETER SWZ99-481680 32 REPLACEMENT DECALS & INFORMATION HEAVY DUTY COMMERCIAL 48072 48072 48314 WARNING DANGER ROTATING BLADES AND BELTS SPINNING BLADE KEEP CLEAR CONTACT CAN INJURE 48071 48071 481040 PARKING BRAKE MANUFACTURED UNDER ONE OR MORE OF THE FOLLOWING PATENTS: CHOKE FAST 4,991,382 4,998,948 4,118,617 4,487,006 4,885,903 4,920,733 4,967,543 KEEP HANDS, FEET & CLOTHING CLEAR KEEP ALL GUARDS IN PLACE SHUT OFF ENGINE & DISENGAGE BLADE CLUTCH BEFORE SERVICING CLEAR AREA OF DEBRIS BEFORE MOWING USE CAUTION IN DIRECTING DISCHARGE KEEP BYSTANDERS, CHILDREN & PETS AWAY READ INSTRUCTION MANUAL BEFORE OPERATING DO NOT OPERATE WITHOUT DISCHARGE CHUTE, MULCHING 481040 KIT, OR ENTIRE GRASS CATCHER INSTALLED 36" - 48316 48" - 48318 52" - 48319 61" - 48320 72" - 48327 OFF PATENTS PENDING ON SLOW 48656 481414 CAUTION MOWER DECK ON BEFORE OPERATING PULL OUT TO ENGAGE READ OPERATORS MANUAL AND SAFETY INSTRUCTIONS CAUTION ON KEEP BYSTANDERS AWAY PUSH IN TO DISENGAGE OFF 48404 48481684 48404 481684 WARNING WARNING MOUNT RIDING ATTACHMENT HERE FALLING HAZARD USE ONLY SCAG APPROVED RIDING ATTACHMENTS INSTALL BELT COVER BEFORE OPERATING MACHINE SEE OPERATOR'S MANUAL READ OPERATOR'S MANUAL 481109 481039 481109 33 481039 REPLACEMENT DECALS & INFORMATION PARKING BRAKE CHOKE FAST OFF ON SLOW 481415 PARKING BRAKE FAST OFF ON SLOW 481423 PARKING BRAKE FAST OFF ON SLOW 481438 34 TRACKING ADJUSTMENT FAST CONTROL ROD ADJUSTMENT REVERSE SEE OPERATOR'S MANUAL NEUTRAL ADJUSTMENT OIL 481425 FORWARD 481425 SEE OPERATOR'S MANUAL SPEED CONTROL 481080 SLOW N NEUTRAL 481124 481124 48514 - 20" 48555 - 16" 35 LIMITED WARRANTY - COMMERCIAL EQUIPMENT Any part of the Scag commercial mower manufactured by Scag Power Equipment and found, in the reasonable judgment of Scag, to be defective in materials or workmanship, will be repaired or replaced by an Authorized Scag Service Dealer without charge for parts and labor. This warranty is limited to the original purchaser and is not transferable. Proof of purchase will be required by the dealer to substantiate any warranty claims. All warranty work must be performed by an Authorized Scag Service Dealer. This warranty is limited to the following specified periods from the date of the original retail purchase for defects in materials or workmanship: * Wear items including drive belts, blades, hydraulic hoses and tires are warranted for ninety (90) days. * Batteries are covered for ninety (90) days. * Frame and structural components including oil reservoir, fittings, and oil coolers are warranted for 1 year. * Cutter decks are warranted against cracking for a period of three (3) years. (Parts and labor 1st year; Parts only 2nd and 3rd year) The repair or replacement of the cutter deck will be at the option of Scag Power Equipment. We reserve the right to request components for evaluation. This warranty does not cover any mower that has been subject to misuse, neglect, negligence, or accident, or that has been operated in any way contrary to the operating instructions as specified in the Operators Manual. * Engines and electric starters are covered by the engine manufacturers warranty period. * Major drive system components (hydraulic pumps and hydraulic motors only) are warranted for two (2) years by Scag Power Equipment. (Parts and labor 1st year; Parts only 2nd year) (Two year warranty excludes fittings, hoses, cooling system, oil reservoir, drive belts, transaxles). The repair or replacement of the hydraulic pump or hydraulic motor will be at the option of Scag Power Equipment. This warranty does not cover any mower that has been subject to misuse, neglect, negligence, or accident, or that has been operated in any way contrary to the operating instructions as specified in the Operators Manual. * Electric clutches have a Limited Warranty for 2 year (Parts and labor 1st year; Parts only 2nd year). * Cutter Spindle Assemblies 46631 have a Limited Warranty for three years (Parts and labor 1st year; Parts only 2nd and 3rd year). * Any Scag product used for rental purposes is covered by a 90 day warranty. The Scag mower, including any defective part must be returned to an Authorized Scag Service Dealer within the warranty period. The expense of delivering the mower to the dealer for warranty work and the expense of returning it to the owner after repair will be paid for by the owner. Scags responsibility is limited to making the required repairs and no claim of breach of warranty shall be cause for cancellation or rescission of the contract of sale of any Scag mower. This warranty does not cover any mower that has been subject to misuse, neglect, negligence, or accident, or that has been operated in any way contrary to the operating instructions as specified in the Operators Manual. The warranty does not apply to any damage to the mower that is the result of improper maintenance, or to any mower or parts that have not been assembled or installed as specified in the Operators Manual and Assembly Manual. The warranty does not cover any mower that has been altered or modified, changing performance or durability. In addition, the warranty does not extend to repairs made necessary by normal wear, or by the use of parts or accessories which, in the reasonable judgment of Scag, are either incompatible with the Scag mower or adversely affect its operation, performance or durability. Scag Power Equipment reserves the right to change or improve the design of any mower without assuming any obligation to modify any mower previously manufactured. All other implied warranties are limited in duration to the one (1) year warranty period or ninety (90) days for mowers used for rental purpose. Accordingly, any such implied warranties including merchantability, fitness for a particular purpose, or otherwise, are disclaimed in their entirety after the expiration of the appropriate one year or ninety day warranty period. Scags obligation under this warranty is strictly and exclusively limited to the repair or replacement of defective parts and Scag does not assume or authorize anyone to assume for them any other obligation. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. Scag assumes no responsibility for incidental, consequential or other damages including, but not limited to, expense for gasoline, expense of delivering the mower to an Authorized Scag Service Dealer and expense of returning it to the owner, mechanics travel time, telephone or telegram charges, rental of a like product during the time warranty repairs are being performed, travel, loss or damage to personal property, loss of revenue, loss of use of the mower, loss of time or inconvenience. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. © 1999 SCAG POWER EQUIPMENT DIVISION OF METALCRAFT OF MAYVILLE, INC. PART NO. 030734 PRINTED 6/99 PRINTED IN USA