Download 1 - Miller Electric
Transcript
FIRE OR EXPLOSION can result from unit on, over, combustible surfaces. placing 1. Do not locate unit on, over, surfaces. 2. Do not install unit near services, or near can cause Have electronic injury. Keep away from moving parts 2. all doors, panels, covers, and and securely in place. such Keep and equipment. only qualified persons familiar with equipment perform this installation. The user is responsible for having a qualified electrician promptly correct any interference problem resulting from the installation. If notified by the FCC about interference, stop using the equipment at once. Have the installation regularly checked and 1. flammables. 1. can navigation, safety computers, communications combustible 2. MOVING PARTS RADIATION HIGH-FREQUENCY interfere with radio near or as fans. 3. guards closed 4. maintained. STATIC ELECTRICITY on circuit boards. 1. Put on boards 2. grounded or can wrist strap BEFORE static-proof bags ship PC boards. OVERUSE 2. Allow can cause and boxes to store, OVERHEATED 4 MAGNETIC FIELDS CURRENTS can 1. cooling period. Follow rated HIGH pacemaker Pacemaker wearers keep away. Wearers should consult their doctor before 2. near Reduce amperage (thickness) or reduce before starting to cut again. FROM affect operation. duty -c plasma going cutting operations. arc SIGNIFICANT DC VOLTAGE exists after removal of input power on inverters. cycle 3. Keep high-frequency source doors and panels tightly shut, keep spark gaps at correct setting, and use grounding and shielding to minimize the possibility of interference. handling EQUIPMENT. 1. 5. parts. Use proper move, or damage parts duty cycle. Turn Off inverter, disconnect 1. input discharge in instructions capacitors input power, according Maintenance Section arid to before touching any parts. 1-4. Principal Safety Standards Safety in Welding and Cutting, ANSI Standard Z49.1, from Ameri Welding Society, 550 N.W. LeJeune Rd, Miami FL 33126 can Safely and Health Standards, OSHA 29 CFR 1910, from tendent of Documents, U.S. Government Safe Handling of Compressed Gases in CGA Cylinders, Pamphlet P-i, from Compressed Gas Association, 1235 Jefferson Davis Highway, Suite 501, Arlington, VA 22202. Superin Printing Office, Washing Code for ton, D.C. 20402. Recommended Practices for Plasma Arc Cutting, American Weld AWS C5.2, from American Welding Society, Safety in Welding and Cutting, CSA Standard W117.2, from Canadian Standards Association, Standards Sales, 178 Rexdale Boulevard, Rexdale, Ontario, Canada M9W 1 R3. ing Society Standard 550 N.W. LeJeune Ad, Miami, FL 33126 Safe Practices For Occupation And Educational Recommended Safe Practices for the Cutting Preparation for Welding and of Containers That Have Held Hazardous Substances, Eye And Face Pro tection, ANSI Standard Z87. 1, from American National Standards Institute, 1430 Broadway, New York, NY 10018. Welding Society Standard AWS F4.1, from American Welding Society, 550 N.W. LeJeune Ad, Miami, FL 33126 American Cutting And Welding Processes, National Electrical Code, NFPA Standard 70, from National Fire Protection Association, Batterymarch Park, Quincy, MA 02269. 1-5. al Fire Protection Association, 02269. NFPA Standard SiB, from Nation Batterymarch Park, Quincy, MA EMF Information Considerations About To reduce Electric And Welding And The Effects Of Low Frequency Magnetic Fields The following is a quotation from the General Conclusions Section of the U.S. Congress, Office of Technology Assessment, Biological Effects of Power Frequency Electric & Magnetic Fields Background Paper, OTA-BP-E-53 (Washington, DC: U.S. there is now a very Government Printing Office, May 1989): . large volume of scientific findings based on experiments at the cellular level and from studies with animals and people which clearly establish that low frequency magnetic fields can interact with, and produce changes in, biological systems. While most of this work is of very high quality, the results are complex. Current scientific understanding does not yet allow us to interpret the evidence in a single coherent framework. Even more frustrating, it does not yet allow us to draw definite conclusions about questions of possible risk or to offer clear science-based advice on strategies to minimize or avoid potential risks. procedures: . . magnetic fields in the 1. Keep 2. Arrange cables 3. Do not coil 4. Keep welding power practical. source 5. Connect work to cables close or to workplace, together by twisting one clamp as following operator. body. and cables workpiece the taping them. side and away from the cables around the drape or use as far away as close to the weld as possible. About Pacemakers: The above wearers. procedures are also recommended for pacemaker Consult your doctor for complete information. OM-182 701 Page 3