Download Denon DRA-697CI Operating instructions

AM-FM STEREO RECEIVER
DRA-697CI
OPERATING INSTRUCTIONS
ENGLISH
SAFETY INSTRUCTIONS
¢SAFETY PRECAUTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
1.
Read Instructions – All the safety and operating instructions should be read
before the product is operated.
2. Retain Instructions – The safety and operating instructions should be
retained for future reference.
3. Heed Warnings – All warnings on the product and in the operating
instructions should be adhered to.
4. Follow Instructions – All operating and use instructions should be followed.
5. Cleaning – Unplug this product from the wall outlet before cleaning. Do not
use liquid cleaners or aerosol cleaners.
6. Attachments – Do not use attachments not recommended by the product
manufacturer as they may cause hazards.
7. Water and Moisture – Do not use this product near water – for example,
near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement;
or near a swimming pool; and the like.
8. Accessories – Do not place this product on an unstable cart, stand, tripod,
bracket, or table. The product may fall, causing serious injury to a child or
adult, and serious damage to the product. Use only with a cart, stand,
tripod, bracket, or table recommended by the manufacturer, or sold with
the product. Any mounting of the product should
follow the manufacturer’s instructions, and should
use a mounting accessory recommended by the
manufacturer.
9. A product and cart combination should be moved
with care. Quick stops, excessive force, and
uneven surfaces may cause the product and cart
combination to overturn.
10. Ventilation – Slots and openings in the cabinet are provided for ventilation
and to ensure reliable operation of the product and to protect it from
overheating, and these openings must not be blocked or covered. The
openings should never be blocked by placing the product on a bed, sofa,
rug, or other similar surface. This product should not be placed in a built-in
installation such as a bookcase or rack unless proper ventilation is provided
or the manufacturer’s instructions have been adhered to.
11. Power Sources – This product should be operated only from the type of
power source indicated on the marking label. If you are not sure of the type
of power supply to your home, consult your product dealer or local power
company. For products intended to operate from battery power, or other
sources, refer to the operating instructions.
12. Grounding or Polarization – This product may be equipped with a polarized
alternating-current line plug (a plug having one blade wider than the other).
This plug will fit into the power outlet only one way. This is a safety feature.
If you are unable to insert the plug fully into the outlet, try reversing the
plug. If the plug should still fail to fit, contact your electrician to replace
your obsolete outlet. Do not defeat the safety purpose of the polarized
plug.
FIGURE A
EXAMPLE OF ANTENNA GROUNDING
AS PER NATIONAL
ELECTRICAL CODE
I
13. Power-Cord Protection – Power-supply cords should be routed so that they
are not likely to be walked on or pinched by items placed upon or against
them, paying particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the product.
15. Outdoor Antenna Grounding – If an outside antenna or cable system is
connected to the product, be sure the antenna or cable system is grounded
so as to provide some protection against voltage surges and built-up static
charges. Article 810 of the National Electrical Code, ANSI/NFPA 70,
provides information with regard to proper grounding of the mast and
supporting structure, grounding of the lead-in wire to an antenna discharge
unit, size of grounding conductors, location of antenna-discharge unit,
connection to grounding electrodes, and requirements for the grounding
electrode. See Figure A.
16. Lightning – For added protection for this product during a lightning storm,
or when it is left unattended and unused for long periods of time, unplug it
from the wall outlet and disconnect the antenna or cable system. This will
prevent damage to the product due to lightning and power-line surges.
17. Power Lines – An outside antenna system should not be located in the
vicinity of overhead power lines or other electric light or power circuits, or
where it can fall into such power lines or circuits. When installing an
outside antenna system, extreme care should be taken to keep from
touching such power lines or circuits as contact with them might be fatal.
18. Overloading – Do not overload wall outlets, extension cords, or integral
convenience receptacles as this can result in a risk of fire or electric shock.
19. Object and Liquid Entry – Never push objects of any kind into this product
through openings as they may touch dangerous voltage points or short-out
parts that could result in a fire or electric shock. Never spill liquid of any
kind on the product.
20. Servicing – Do not attempt to service this product yourself as opening or
removing covers may expose you to dangerous voltage or other hazards.
Refer all servicing to qualified service personnel.
21. Damage Requiring Service – Unplug this product from the wall outlet and
refer servicing to qualified service personnel under the following
conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the
operating instructions as an improper adjustment of other controls may
result in damage and will often require extensive work by a qualified
technician to restore the product to its normal operation,
e) If the product has been dropped or damaged in any way, and
f) When the product exhibits a distinct change in performance – this
indicates a need for service.
22. Replacement Parts – When replacement parts are required, be sure the
service technician has used replacement parts specified by the
manufacturer or have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock, or other
hazards.
23. Safety Check – Upon completion of any service or repairs to this product,
ask the service technician to perform safety checks to determine that the
product is in proper operating condition.
24. Wall or Ceiling Mounting – The product should be mounted to a wall or
ceiling only as recommended by the manufacturer.
25. Heat – The product should be situated away from heat sources such as
radiators, heat registers, stoves, or other products (including amplifiers)
that produce heat.
ENGLISH
FCC INFORMATION (For US customers)
¢NOTE ON USE
1. PRODUCT
This product complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this product may not cause harmful
interference, and (2) this product must accept any interference received,
including interference that may cause undesired operation.
2. IMPORTANT NOTICE: DO NOT MODIFY THIS PRODUCT
This product, when installed as indicated in the instructions contained in this
manual, meets FCC requirements. Modification not expressly approved by
DENON may void your authority, granted by the FCC, to use the product.
3. NOTE
This product has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This product generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
product does cause harmful interference to radio or television reception,
which can be determined by turning the product OFF and ON, the user is
encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the product into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the local retailer authorized to distribute this type of product or
an experienced radio/TV technician for help.
• Do not let foreign objects into the apparatus.
• Keep the apparatus free from moisture, water, and
dust.
• Avoid high temperatures.
Allow for sufficient heat dispersion when installed
in a rack.
• Unplug the power cord when not using the
apparatus for long periods of time.
• Do not let insecticides, benzene, and thinner come
in contact with the apparatus.
• Handle the power cord carefully.
Hold the plug when unplugging the cord.
* (For apparatuses with ventilation holes)
• Do not obstruct the ventilation holes.
II
• Never disassemble or modify the apparatus in any
way.
ENGLISH
Thank you for choosing the DENON DRA-697CI AM-FM Stereo Receiver. This remarkable component has been engineered to provide
outstanding high fidelity reproduction of your favorite music sources.
As this product is provided with an immense array of features, we recommend that before you begin hookup and operation that you review
the contents of this manual before proceeding.
Operating the remote control unit
Operating DENON audio components ·······································22
Setting the preset memory function ··········································22
Setting the punch through function···········································22
Operating a component stored in the preset memory ····22 ~ 24
Contents
Troubleshooting ············································································25
Getting Started
Accessories······················································································1
Before using ····················································································2
Cautions on installation ·································································2
About the remote control unit························································2
Inserting the batteries ····································································2
Operating range of the remote control unit ································2
Part names and functions······························································3
Front panel ·····················································································3
Display····························································································3
Rear panel ······················································································4
Remote control unit ···································································4, 5
Connections
Cable indications ············································································5
Speaker connections ······································································6
Connecting a DVD player and monitor ········································6
Connecting a TV/DBS tuner ··························································7
Connecting a CD player ·································································7
Connecting a turntable ··································································7
Connecting a tape deck, CD recorder or MD recorder················7
Connecting a VCR···········································································7
Connecting the antenna terminals ···············································8
Connecting the XM terminal ·························································8
Connecting the iPod® ····································································9
Connecting the MULTI ZONE terminals ·······································9
ZONE2 (or ZONE3) PRE OUT connections ····································9
Connecting the TRIGGER OUT jacks ··········································10
Connecting the RS-232C terminal···············································10
Connecting the AUDIO PRE OUT/MAIN IN terminals ··············10
Connecting the power supply cord ············································10
Setup Menu
Setting the iPod Assignment····················································11
Setting the Trigger Out ·····························································11
Setting the High Pass Filter ······················································12
Operation
Before operating ···········································································12
Playing the input source ······························································12
Turning the sound off temporarily (MUTING)·······························12
Listening over headphones ··························································12
Switching the speakers ·······························································12
Checking the currently playing program source, etc. ··················13
Switching the brightness of the display·······································13
Selecting the play mode (PURE DIRECT) ····································13
Setting the tone control ·······························································13
Adjusting the speaker volume ·····················································13
Combining the currently playing sound
with the desired image (VIDEO SELECT function)····················13
Listening to the radio···································································14
Auto preset memory ····································································14
Auto tuning···················································································14
Manual tuning ··············································································14
Preset memory ············································································14
Recalling preset stations ······························································14
XM Satellite Radio········································································15
Checking the XM signal strength and Radio ID ···························16
Channel selection·········································································16
Category search ···········································································16
Direct access of channels ····························································16
Playing the iPod® ·········································································17
Listening to music········································································17
Listening to music in the Browse mode······································18
Viewing still pictures and videos (only for iPods
equipped with the slideshow/video function) ······························18
Disconnecting the iPod ································································18
Multi zone music entertainment system ···································19
Multi-zone playback using the ZONE2 and
ZONE3 PREOUT terminals···························································19
Outputting a program source to amplifier, etc., in the ZONE2
(or ZONE3) room (ZONE2 or ZONE3 SELECT mode) ··················20
Remote control unit operations during multi-source playback·····20
Recording (audio and/or video) ··················································21
About the memory functions ······················································21
Initialization of the microprocessor············································21
1
ENGLISH
Specifications ················································································26
Getting Started
Accessories
Check that the following parts are attached in addition to the main
unit:
q Operating instructions ..............................................................1
w Warranty (for North America model only).....................................1
e Service station list ....................................................................1
r Power supply cord (Approx. 5.6 ft / 1.7 m) ..............................1
t System remote control unit (RC-1052).....................................1
y R6P/AA batteries (For the RC-1052).........................................2
u ZONE remote control unit (RC-1056) .......................................1
i R03/AAA batteries (For the RC-1056) ......................................2
o AM loop antenna ......................................................................1
!0 FM indoor antenna ...................................................................1
t
r
u
i
y
o
!0
ENGLISH
Getting Started
Getting Started
Before using
About the remote control unit
Pay attention to the following before using this unit:
• Moving the unit.
To prevent short-circuits or damaged wires in the connection cables,
always unplug the power supply cord and disconnect the connection
cables between all other audio components when moving the unit.
• Cautions on using mobile phones.
Using a mobile phone near this unit may result in noise. If so, move
the mobile phone away from this unit when it is in use.
• Before turning the power operation button on.
Check once again that all connections are correct and that there are
not problems with the connection cables. Always set the power
operation button to the standby position before connecting and
disconnecting connection cables.
In addition to controlling the DRA-697CI, the attached system remote
control unit (RC-1052) can also be used to control the following
products:
q DENON component products
w Component products other than DENON:
• Set using the preset memory function (
page 22).
Inserting the batteries
q Remove the remote control unit’s rear cover.
• Store the operating instructions in a safe place.
After reading the operating instructions, store them in a safe place
as they could come in handy in the future.
• Whenever the power operation button is in the STANDBY state,
the unit is still connected to AC line voltage.
Please be sure to turn off the power switch or unplug the cord
when you leave home for, say, a vacation.
• Note that the illustrations in these instructions may differ from
the actual unit for explanation purposes.
Notes on batteries:
• Replace the batteries with new ones if the set does not operate
even when the remote control unit is operated nearby the unit.
(The attached batteries are only for verifying operation.)
• When inserting the batteries, be sure to do so in the proper
direction, following the “<” and “>” marks in the battery
compartment.
• To prevent damage or leakage of battery fluid:
• Do not use a new battery together with an old one.
• Do not use two different types of batteries.
• Do not short-circuit, disassemble, heat or dispose of batteries
in flames.
• If the battery fluid should leak, carefully wipe the fluid off the
inside of the battery compartment and insert new batteries.
• Remove the batteries from the remote if it will not be in use for
long periods.
• When replacing the batteries, have the new batteries ready and
insert them as quickly as possible.
Operating range of the remote control unit
(RC-1052)
(RC-1056)
w Set two batteries in the battery compartment in the indicated
direction.
Cautions on installation
R6P/AA
• Point the remote control unit at the remote sensor when operating
it.
• The remote control unit can be used from a distance of approximately
23 feet/7 meters, at a horizontal angle of up to 30° with respect to
the sensor.
R03/AAA
Note:
For heat dispersal, do not install this unit in a confined space
such as a bookcase or similar enclosure.
Note
(RC-1052)
(RC-1056)
30°
30°
e Put the rear cover back on.
Approx. 23 feet/7 m
or
(RC-1056)
(RC-1052)
NOTE:
• The set may function improperly or the remote control unit may
not operate if the remote control sensor is exposed to direct
sunlight, strong artificial light from an inverter type fluorescent
lamp or infrared light.
Wall
2
ENGLISH
ENGLISH
Getting Started
Getting Started
Part names and functions
Display
For details on the functions of these parts, refer to the pages given in parentheses ( ).
t
i u y
r
e
Front panel
@7
@6
@5 @4
@3
@2 @1 @0
!9
!8
w
q
q Information display
w Speaker indicators
This lights corresponding to the settings of the
front speakers.
e ZONE2/ZONE3 output indicators
r Volume indicator
qwe
t
i
!0
r y u
o !1 !2
q Power operation button
(ON/STANDBY) ··········································(12)
w Power indicator ·········································(12)
e Power switch ·······································(12, 21)
r Headphones jack (PHONES) ·····················(12)
t MODE button ·······································(14, 18)
y SPEAKER buttons ······································(12)
u PURE DIRECT button·································(13)
i SHIFT button ··············································(14)
o XM RADIO button······································(16)
!0 TONE DEFEAT button ·······························(13)
!1 LOUDNESS button ····································(13)
!2 STATUS button ··········································(13)
!3 MENU button ·············································(11)
This displays the volume level.
t ZONE/REC SELECT indicators
!3 !4 !5 !6 !7
Lights while selecting the ZONE or REC
SELECT mode. (Off when the “SOURCE” is
selected.)
!4 TONE CONTROL button····························(13)
!5 SELECT knob········································(13, 17)
!6 CH VOL button···········································(13)
!7 ENTER button ······································(11, 18)
!8 VOLUME control knob ······························(12)
!9 ZONE on/standby buttons ·······················(20)
@0 Display
@1 TUNING buttons (•, ª) ·····························(14)
@2 PRESET buttons·········································(14)
@3 MEMORY button········································(14)
@4 Remote control sensor································(2)
@5 BAND button··············································(14)
@6 ZONE select buttons ·································(20)
@7 FUNCTION knob ········································(12)
3
ENGLISH
y AUTO indicator
This lights when the broadcast station is selected
in the AUTO tuning mode.
u STEREO indicator
This lights when an FM stereo broadcast has
been received.
i TUNED indicator
This lights when an FM/AM broadcast has been
received.
ENGLISH
Getting Started
Getting Started
Rear panel
Remote control unit
!6 e
!8 !7 !5 !4 !3 !2
¢ System remote control unit (RC-1052)
!1
!0
o
[ Front ]
Remote control signal
transmitter ························(2)
Indicator ··························(22)
Power buttons················(12)
SHIFT button ··················(14)
CHANNEL buttons ·········(14)
Function buttons············(12)
q
t
w e r y
q AUDIO OUT terminals·································(7)
w SUBWOOFER PRE OUT terminal ···············(6)
e AUDIO IN terminals·····························(6, 7, 9)
r ZONE PRE OUT terminals···························(9)
t TRIGGER OUT jacks ··································(10)
y ZONE VIDEO OUT terminals ······················(9)
u Speaker terminals ·······································(6)
i AC outlets···················································(10)
o AC inlet ·······················································(10)
u
i
System buttons··············(23)
Volume control
buttons ····························(12)
!0 AUDIO PRE OUT / MAIN IN terminals ····(10)
!1 VIDEO IN terminals ·····································(7)
!2 VIDEO OUT terminals ·····························(6, 7)
!3 RS-232C terminal ·······································(10)
!4 SIGNAL GND terminal ································(7)
!5 XM terminal ·················································(8)
!6 DOCK CONTROL jack ··································(9)
!7 ANTENNA terminals ···································(8)
!8 REMOTE CONTROL jacks ···························(9)
MUTING button··············(12)
MENU button ·················(11)
DIMMER button··············(13)
Cursor buttons
(D, H, F, G) ····················(17)
ENTER button···········(11, 18)
STATUS button ··············(13)
VIDEO SELECT
button······························(13)
PURE DIRECT button ·····(13)
Mode selector
switches ··············(12, 20, 22)
NOTE:
• If buttons on the front or rear are pressed strongly, the button on the opposite side will be activated
too.
4
ENGLISH
ENGLISH
Getting Started
[ Rear ]
Connections
NOTE:
• If buttons on the front or rear are
pressed strongly, the button on
the opposite side will be
activated too.
ZONE3 ON/OFF
buttons ····························(20)
ZONE2 ON/OFF
buttons ····························(20)
Cable indications
The hookup diagrams on the subsequent pages assume the use of the following optional connection
cables (not supplied).
Audio cable
Number buttons
(0 ~ 9, +10) ··········(14, 16, 22)
A
D
Analog connections (Stereo)
(White)
L
L
(Red)
R
R
BAND button ··················(14)
B
MODE button············(14, 18)
Video connections
(Yellow)
Pin-plug cable
Memory block
buttons (A ~ G)···············(14)
Video cable
Video cable (75 Ω/ohms video pin-plug cable)
Analog connections
(Monaural, for subwoofer)
Signal direction
Function buttons············(12)
Audio signal
MEMORY button ············(14)
MAIN ZONE ON/OFF
buttons ····························(20)
Pin-plug cable
IN
TUNING buttons ············(14)
C
Speaker connections
OUT
IN
Video signal
IN
¢ ZONE remote control unit (RC-1056)
OUT
OUT
OUT
IN
Speaker cable
[ Front ]
ZONE select switch········(20)
NOTE:
• Do not plug in the power supply cord until all connections have been completed.
• When making connections, also refer to the operating instructions of the other components.
• Be sure to connect the left and right channels properly (left with left, right with right).
• Do not bundle power cords together with speaker cables. Doing so could result in humming or noise.
ZONE ON/OFF
buttons ····························(20)
Function buttons············(20)
Number buttons
(0 ~ 9)·························(14, 16)
Volume control
buttons ····························(20)
SEARCH button ··············(16)
Memory block
buttons (A ~ G)···············(14)
BAND button ··················(14)
5
ENGLISH
ENGLISH
Connections
Connections
¢ Connections
Speaker connections
Connect the speaker terminals with the speakers
making sure that like polarities are matched (<
with <, > with >).
NOTE:
When making connections, take care that
none of the individual conductors of the
speaker cable come in contact with adjacent
terminals, with other speaker cable
conductors, or with the rear panel and
screws.
NEVER touch the speaker terminals when
the power is on. Doing so could result in
electric shocks.
Connecting the speaker cables
1. Loosen by turning
counterclockwise.
2. Insert the cable.
Either tightly twist or terminate the
core wires.
• When making connections, also refer to the operating instructions of the other components.
¢ Speaker impedance
Speaker
Impedance
A, B
4 ~ 16 Ω/ohms
A+B
8 ~ 16 Ω/ohms
Speakers
(B)
Subwoofer
(L)
IN
Note on speaker impedance
Connection terminal for
subwoofer with built-in
amplifier.
When using speakers with an impedance
below the designated value (for example 4
Ω/ohms), playing for long periods of time with
the volume high could cause the temperature
to rise, activating the protection circuit.
When the protection circuit is activated, the
output to the speakers is cut off and the power
indicator blinks. If this happens, unplug the
power cord, wait for the set to cool off and
improve ventilation around the unit. Also check
the wiring of the input cables and the speaker
cables. After doing this, plug the power cord
back in and turn the unit’s power back on.
If the protection circuit is activated again even
though there are no problems with the wiring or
the ventilation around the unit, switch off the
power and contact a DENON service center.
B
<
Speakers
(A)
(R)
>
>
(L)
<
<
C
(R)
>
>
<
C
Connecting a DVD player and monitor
3. Tighten by turning clockwise.
Monitor
D
VIDEO
IN
Connecting banana plugs
D
DVD player
VIDEO
OUT
Turn clockwise to tighten, then
insert the banana plug.
AUDIO OUT
A
L
L
L
R
R
R
• Connect a non-DVD video disc player (such as a laser disc, VCD/SVCD, or future high definition disc
player) to the DVD/VDP terminals in the same way.
6
ENGLISH
ENGLISH
Connections
Connections
Connecting a TV/DBS tuner
• The phono input can accept signals from moving magnet (MM) and high output moving coil (MC) phono
cartridges. If your turntable is equipped with a low output MC cartridge, you will need to use a separate
MC head amplifier or step-up MC transformer.
NOTE:
• If humming or other noise is generated when the ground wire is connected to the SIGNAL GND
terminal, disconnect the ground wire.
TV/DBS tuner
D
VIDEO
OUT
AUDIO OUT
A
L
L
R
R
L
Connecting a tape deck, CD recorder or MD recorder
R
Tape deck/
CD recorder/
MD recorder
Connecting a CD player
AUDIO IN
A
L
L
L
R
R
R
AUDIO OUT
A
CD player
L
L
R
R
L
R
AUDIO OUT
A
L
L
R
R
L
R
Connecting a VCR
Video deck
D
VIDEO
IN
Connecting a turntable
D
VIDEO
OUT
Turntable
Turntable
(MM cartridge)
cartridge)
(MM
AUDIO OUT
A
L
L
R
R
R
AUDIO IN
A
A
L
L
AUDIO OUT
R
GND
7
ENGLISH
L
L
L
R
R
R
ENGLISH
Connections
Connections
Connecting the antenna terminals
Connecting the XM terminal
• DRA-697CI is the XM Ready® receiver. You can receive XM® Satellite Radio by connecting to the XM
Mini-Tuner and Home Dock (includes home antenna, sold separately) and subscribing to the XM service.
• Position the Home Dock antenna near a south-facing window to receive the best signal.
For details, see “XM Satellite Radio” (
page 15, 16).
When making connections, also refer to the operating instructions of the XM Mini-Tuner and Home
Dock.
An F-type FM antenna cable plug can be connected directly.
Direction of broadcasting
station
FM antenna
AM loop antenna
(Supplied)
75 Ω/ohms Coaxial
cable
XM Mini-Tuner and
Home Dock
AUX OUT
XM
FM indoor antenna (Supplied)
AM outdoor antenna
Ground
¢ AM loop antenna assembly
Connect to the AM
antenna terminals.
1
2
NOTE:
• Keep the power supply cord unplugged until the XM Mini-Tuner and Home Dock connection has been
completed.
Connection of AM antennas
1. Push the lever.
• The XM name and related logo are registered trademarks of XM Satellite Radio Inc. All rights
reserved.
• XM Ready is a registered trademark of XM Satellite Radio Inc. All rights reserved.
3
2. Insert the conductor.
Remove the vinyl tie
and take out the
connection line.
Bend in the reverse
direction.
3. Return the lever.
4
a. With the antenna on
top any stable
surface.
Mount
b. With the antenna
attached to a wall.
Installation hole Mount on wall, etc.
NOTE:
• Do not connect two FM antennas
simultaneously.
• Even if an external AM antenna is used, do
not disconnect the AM loop antenna.
• Make sure the AM loop antenna lead
terminals do not touch metal parts of the
panel.
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC
which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall
be connected to the grounding system of the building, as close to the point of cable entry as practical.
8
ENGLISH
ENGLISH
Connections
Connecting the
Connections
iPod®
Connecting the MULTI ZONE terminals
For instructions on operations using the MULTI ZONE functions (
When using an iPod, you must connect the Control Dock for iPod (ASD-1R, sold separately) and the DOCK
CONTROL jack on the DRA-697CI with a mini-jack and assign the iPod to any AUDIO terminal(s).
The diagram below shows an example of connections for when the iPod is assigned to the CD-R/TAPE
terminals.
page 19).
ZONE2 (or ZONE3) PRE OUT connections
• If another power amplifier or pre-main (integrated) amplifier is connected, the ZONE2 (or ZONE3) preout (variable or fixed level) terminals can be used to play a different program source in ZONE2 (or
ZONE3) the same time (
page 19).
• The ZONE2 video out is only for the ZONE2.
• The ZONE3 video out is only for the ZONE3.
For instructions on assigning the iPod to a specific terminal, see “Setting the iPod Assignment” (
page 11).
For instructions on playing the iPod, see “Playing the iPod” (
page 17).
iPod
Input
+
Extension terminal for future use.
AUX OUT
Infrared retransmitter
ASD-1R
Output
+
G
Infrared sensor
Monitor
Monitor
(ZONE2
or ZONE3)
(ZONE2)
VIDEO
IN
A
R
R
L
L
A
AUDIO OUT
Power
Power amplifier
amplifier
(ZONE2 or
or ZONE3)
ZONE3)
(ZONE2
L
L
L
R
R
R
IN
Monitor (S VIDEO IN)
• The optional standard Control Dock for iPod is DENON ASD-1R sold separately.
• For the AUDIO output, use high quality pin-plug cables and wire in such a way that there is no humming
or noise.
• For instructions on installation and operation of separately sold devices, refer to the devices’ operating
instructions.
9
ENGLISH
ENGLISH
Connections
Connections
Connecting the TRIGGER OUT jacks
Connecting the AUDIO PRE OUT/MAIN IN terminals
A
Premain amplifier or
Power amplifier
(MAIN)
L
L
L
R
R
R
IN
Turn the DC 12 V voltage on and off for the
individual functions.
A
L
L
L
R
R
R
OUT
Connecting the RS-232C terminal
Connecting the power supply cord
This terminal is used for an external controller.
AC outlet
(wall)
Perform the following operation before using an
external controller connected to the RS-232C
terminal:
1. Press the ON/STANDBY button on the main unit
and set the unit to the operating mode.
2. Perform the operation to turn off the power
from the external control.
3. Check that the product has been set to the
standby mode.
After checking the above, check the connections of
the external controller. Operation is possible.
Power supply cord
(Supplied)
AC 120 V, 60 Hz
AC OUTLETS
• SWITCHED (total capacity – 120 W (1 A))
The power to the outlet is turned on and off in
conjunction with the POWER switch on the
main unit, and when the power is switched
between on and standby from the remote
control unit.
No power is supplied from this outlet when
this unit’s power is at standby. Never connect
equipment whose total power consumption
exceeds 120 W (1 A).
NOTE:
• Insert the plugs securely. Incomplete connections will result in the generation of noise.
• Only use the AC OUTLETS for audio equipment. Never use it for hair driers, monitors or other
electrical appliances.
10
ENGLISH
ENGLISH
FUNCTION
<SPEAKER>
MENU
ENTER
VOLUME
Setup Menu
Setting the iPod Assignment
It is possible to assign the Control Dock for iPod’s (ASD-1R, sold
separately) audio to any input terminals on the DRA-697CI and play
them.
<POWER>
<ON/STANDBY> <PHONES>
<SELECT>
<CH VOL>
[POWER ON]
FUNCTION
VOLUME
ENTER
MENU
[MODE SELECTOR 1]
[MUTING]
[D H F G]
[MODE SELECTOR 2]
1
Press MENU with the function set to something other
“FM/AM”, “XM” or the function selected at “iPod
Assignment”.
2
D H] to select “iPod Assign”,
Press <CH VOL> or [D
then press ENTER.
3
F G] to set.
Use <SELECT> or press [F
Setting the Trigger Out
Use the DC 12 V output of the DRA-697CI’s two trigger out jacks in
association with the various input sources.
MENU with the function set to something other
1 Press
“FM/AM”, “XM” or the function selected at “iPod
Assignment”.
<CH VOL> or [D
D H] to select “Trigger Out”,
2 Press
then press ENTER.
<SELECT> or press [F
F G] to select the trigger out
3 Use
jacks, then press ENTER.
DVD, VCR, V.A:
When using a Control Dock for iPod, it is possible to connect with
the audio and video input terminals of the assigned function.
<SELECT> or press [F
F G] to select “ZONE”, then
4 Use
press ENTER.
CDR, CD:
When using a Control Dock for iPod, it is possible to connect with
the audio input terminal of the assigned function.
<CH VOL> or [D
D H] to select the input source,
5 Press
F G] to set.
then use <SELECT> or press [F
None:
Select this when not assigning an iPod to the DRA-697’s input
terminal.
ON, OFF:
When that input source is selected, the power supplied from the
trigger out jack turns on or off.
6 Press ENTER.
4 Press ENTER.
Canceling setup menu:
To cancel the setup menu press MENU.
Canceling setup menu:
To cancel the setup menu press MENU.
1
System Setu p
FUNCTION
2
System Setu p
iPod Assign
3
About the button names in this explanation
<
> : Buttons on the main unit
[
] : Buttons on the remote control unit
Button name only :
Buttons on the main unit and remote control unit
iPod Assign
iPod:
DVD
1
System Setu p
2
System Setu p
Trigger Out
3
Trigger Out
Trigger Out 1
4
Trigger Out 1
ZONE
2/3
5
11
ENGLISH
Trigger Out 1
DVD/VDP
ON
ENGLISH
Setup Menu
Setting the High Pass Filter
Set this to “ON” if your speakers do not have a very strong capacity
for producing low bass.
Operation
Before operating
Turning the sound off temporarily (MUTING)
MENU with the function set to something other
1 Press
“FM/AM”, “XM” or the function selected at “iPod 1 Press <POWER>.
Assignment”.
Press [MUTING].
¢ ON:
2
D H] to select “H. P. F.”, then
Press <CH VOL> or [D
press ENTER.
The power indicator lights red.
£ OFF:
The power turns off and the indicator is off.
3 Use <SELECT> or press [FF G] to set.
OFF:
Select this when not using a high pass filter.
ON:
Using the high pass filter makes it possible to reduce distortion of
the bass sound.
2 Set [MODE SELECTOR 1] to “A”.
3 Set [MODE SELECTOR 2] to “CD/iPod”.
4 Press <ON/STANDBY> or [POWER ON].
• Canceling MUTING mode:
To cancel the muting mode, either press [MUTING] or adjust the
volume.
Listening over headphones
Connect the headphones to <PHONES>.
• No sound is produced from the speakers automatically.
• The power indicator blinks green and the power turns on.
4
Press ENTER.
Canceling setup menu:
To cancel the setup menu press MENU.
1
System Setu p
2
System Setu p
H.P.F.
3
H.P.F.
ON/OFF:
OFF
NOTE:
• To prevent hearing loss, be careful not to raise the volume level
excessively when using headphones.
Playing the input source
FUNCTION to select the input source you want to
1 Use
play.
2
Start playback on the selected component.
For operating instructions, refer to the component’s manual.
3 Use VOLUME to adjust the volume.
• The volume level is displayed on the volume level display.
12
ENGLISH
Switching the speakers
Press <SPEAKER> to turn the corresponding speaker pair
on.
ENGLISH
Operation
Operation
MENU
ENTER
FUNCTION MODE <PRESET>
BAND SHIFT TUNING
<SELECT>
STATUS
Checking the currently playing program source,
etc.
¢ When you do not want to adjust the tone
Press <TONE DEFEAT> to select “TONE DEFEAT ON”.
Press STATUS.
• The current program source and various settings are indicated on
the display.
¢ When listening with the volume turned low
Press <LOUDNESS> to select “LOUDNESS ON”.
Switching the brightness of the display
<ON/STANDBY> PURE DIRECT <LOUDNESS>
<CH VOL>
MEMORY <TONE DEFEAT> <TONE CONTROL>
Press [DIMMER].
Adjusting the speaker volume
The brightness of the display can be adjusted in three steps. The
display can also be turned off.
1 Press <CH VOL> to select the speaker.
The settable speaker switches each time this button is pressed.
SHIFT
[FM/AM]
[CHANNEL]
FUNCTION
ENTER
MENU
STATUS
PURE DIRECT
Selecting the play mode (PURE DIRECT)
This mode reproduces the sound with extremely high quality. The
display that could affect the audio signals are turned “OFF”.
Press PURE DIRECT.
2 Use <SELECT> to adjust the volume.
Can be adjusted within the range of –12 dB to +12 dB.
Combining the currently playing sound with the
desired image (VIDEO SELECT function)
[DIMMER]
[VIDEO SELECT]
Setting the tone control
Press [VIDEO SELECT] until the desired image appears
on the display.
¢ Adjusting the tone
<TONE
1 Press
“TREBLE”.
[NUMBER]
(0 ~ 9, +10)
2 Use <SELECT> to set the level.
BAND
[MEMORY BLOCK]
FUNCTION
CONTROL> to select “BASS” or
MODE
MEMORY
Can be adjusted within the range of –10 dB to +10 dB.
TUNING
About the button names in this explanation
<
> : Buttons on the main unit
[
] : Buttons on the remote control unit
Button name only :
Buttons on the main unit and remote control unit
13
ENGLISH
• To cancel, press [VIDEO SELECT] to select “SOURCE”.
• The video source selected with the video select function is stored in
the memory for the different input sources.
ENGLISH
Operation
Operation
Listening to the radio
Check that the remote control unit is set to “A”.
Auto preset memory
Auto tuning
FUNCTION
1 Use
“FM/AM”.
Preset memory
or press [FM/AM] to select
the “Auto tuning” or “Manual tuning” operation
1 Use
to tune in the station to be preset in the memory.
1 With the function set to “FM/AM”, press MENU.
2 Press BAND to select “AM” or “FM”.
3 Press MODE to set the auto tuning mode.
2 Press MEMORY.
Press [MEMORY BLOCK] (A to G) or SHIFT to select
3 the
desired memory block (A to G).
2 Press ENTER.
4 Press TUNING.
Press <PRESET>, [CHANNEL] or [NUMBER] to select
4 the
desired preset channel (1 to 8).
This unit is equipped with a function for automatically searching for
FM broadcast stations and storing them in the preset memory.
• “Auto Preset” is displayed.
• The unit automatically begins searching for FM broadcast
stations.
When the first FM broadcast station is found, that station is
stored in the preset memory at channel A1.
Subsequent stations are automatically stored in order at preset
channels A1 to A8, B1 to B8, C1 to C8, D1 to D8, E1 to E8, F1 to
F8 and G1 to G8 for a maximum of 56 stations.
Channel A1 is tuned in after the auto preset memory operation is
completed.
• The “AUTO” indicator lights.
• Automatic searching begins.
5 Press MEMORY again.
• Store the station in the preset memory.
• If tuning does not stop at the desired station, use to the “Manual
tuning” operation.
• “AM” or “FM” can be selected directly by pressing [FM/AM].
• To preset other channels, repeat steps 2 to 5.
A total of 56 broadcast stations can be preset — 8 stations (channels
1 to 8) in each of blocks A to G.
Manual tuning
• If an FM station cannot be preset automatically due to poor
reception, use the “Manual tuning” operation to tune in the station,
then preset it using the manual “Preset memory” operation.
• To interrupt this function, press <ON/STANDBY>.
¢ Default settings
A1 ~ A8
B1 ~ B8
C1
D1
E1
F1
G1
~
~
~
~
~
C8
D8
E8
F8
G8
Auto tuner presets
87.5 / 89.1 / 98.1 / 107.9 / 90.1 / 90.1 / 90.1 /
90.1 MHz
520 / 600 / 1000 / 1400 / 1500 / 1710 kHz,
90.1 / 90.1 MHz
90.1 MHz
90.1 MHz
90.1 MHz
90.1 MHz
90.1 MHz
FUNCTION
1 Use
“FM/AM”.
or press [FM/AM] to select
Recalling preset stations
2 Press BAND to select “AM” or “FM”.
3 Press MODE to set the manual tuning mode.
Check that the display’s “AUTO” indicator turns off.
4 Press TUNING.
The frequency changes continuously when the button is held in.
• When the manual tuning mode is set, FM stereo broadcasts are
received in monaural and the “STEREO” indicator turns off.
14
ENGLISH
Press [MEMORY BLOCK] (A to G) or SHIFT to select
1 the
memory block.
Press <PRESET>, [CHANNEL] or [NUMBER] to select
2 the
desired preset channel.
ENGLISH
Operation
Operation
ENTER
FUNCTION
STATUS
¢ XM READY® SUBSCRIPTIONS
XM Satellite Radio
¢ ABOUT XM SATELLITE RADIO
XM Satellite Radio offers an extraordinary variety of commercial-free
music, plus the best in sports, news, talk and entertainment. XM is
broadcast in superior digital audio from coast to coast. From rock to
reggae, from classical to hip hop, XM has something for every music
fan. XM’s dedication to playing the richest selection of music is
matched by its passion for live sporting events, talk radio, up-to-theminute news, stand-up comedy, children’s programming, and much
more. For U.S. customers, information about XM Satellite Radio is
available online at www.xmradio.com. For Canadian customers,
information about XM Canada is online at www.xmradio.ca.
XM RADIO
FUNCTION
TUNING
¢ XM READY® LEGAL
XM RADIO
ENTER
STATUS
[D H F G]
Hardware and required monthly subscription sold separately. Other
fees and taxes, including a one-time activation fee may apply.
Subscription fee is consumer only. All fees and programming subject
to change. Channels with frequent explicit language are indicated with
an XL. Channel blocking is available for XM radio receivers by calling
1-800-XMRADIO (US residents) and 1-877-GET-XMSR (Canadian
residents).
For a full listing of the XM commercial-free channels and advertisingsupported channels, visit lineup.xmradio.com (US residents) or
xmradio.ca (Canadian residents).
Subscriptions subject to Customer Agreement available at
xmradio.com (US residents) and xmradio.ca (Canadian residents).
Only available in the 48 contiguous United States and Canada. ©2006
XM Satellite Radio Inc. All rights reserved. All other trademarks are
the property of their respective owners.
[NUMBER]
(0 ~ 9, +10)
[SEARCH]
FUNCTION
TUNING
About the button names in this explanation
<
> : Buttons on the main unit
[
] : Buttons on the remote control unit
Button name only :
Buttons on the main unit and remote control unit
15
ENGLISH
Once you have installed the XM Mini-Tuner Dock, inserted the XM
Mini-Tuner, connected the XM Dock to your XM Ready® home audio
system, and installed the antenna, you are ready to subscribe and
begin receiving XM programming. There are three places to find your
eight character XM Radio ID: on the XM Mini-Tuner, on the XM MiniTuner package, and on XM Channel 0. Record the Radio ID in the
following eight squares for reference.
Note: The XM Radio ID does not use the letters “I”, “O”, “S” or “F”.
Activate your XM Satellite Radio service in the U.S. online at
http://activate.xmradio.com or call 1-800-XM-RADIO (1-800-9672346). You will need a major credit card. XM will send a signal from
the satellites to activate the full channel lineup. Activation normally
takes 10 to 15 minutes, but during peak busy periods you may need
to keep your XM Ready home audio system on for up to an hour.
When you can access the full channel lineup on your XM Ready home
audio system you are done. For more information or to subscribe in
Canada, visit XM on the Web at www.xmradio.ca or call XM’s Listener
Care at 1-877-GET-XMSR (1-877-438-9677).
ENGLISH
Operation
Operation
Checking the XM signal strength and Radio ID
Channel selection
Direct access of channels
1 Use FUNCTION to select “XM” or press XM RADIO. 1 Use FUNCTION to select “XM” or press XM RADIO. 1 Press [SEARCH] in the XM mode.
2 Press TUNING to reach the desired channel.
2 Press STATUS until “SIGNAL” is displayed.
2 Press [NUMBER] to enter the desired channel.
• The display changes as shown below according to the receiving
condition.
X M___
DIRECT SEARCH
Channel number
XM040
DeepTrks
¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡
Display
Condition
GOOD
Signal strength is good
MARGINAL
Signal strength is marginal
WEAK
Signal strength is poor
NO
Loss of the signal
the antenna location until “SIGNAL:GOOD”
3 Adjust
is displayed.
Channel name
Song title / Artist name
The channel changes continuously when you press and hold
TUNING.
When the artist name and song title are received, they are
displayed.
For example, if you want to access channel 123 (ex.XM123)
press [NUMBER] as shown below.
XM001
DIRECT SEARCH
Category search
XM012
DIRECT SEARCH
Press STATUS until the XM channel (ex.XM001) is
4 displayed.
1 Press [FF G] in the XM mode.
• The current category name is displayed.
XM123
DIRECT SEARCH
5 Press TUNING to select channel 0 (XM000).
XM000
RADIO ID
¡¡¡¡¡¡¡¡
Radio ID
XM006
CAT:
60's
Rock
Channel category
(Remote control unit)
F G] to select the category, and press [D
D H] to
[F
Once all number have been input, press ENTER to
2 Press
3 change
select the channel within the selected category.
the channel.
• “LOADING” is displayed while receiving the channel or information.
• “UPDATING” is displayed while updating encryption code.
• When the selected channel is not available, “XM – – –” is displayed.
• Information on the artist name, song title, category and signal level
can be checked using STATUS.
• The XM Satellite Radio channels can be preset in the same way as
AM/FM band.
• In addition to AM/FM band presetting, a total of 56 stations can be
preset.
• “XM” can be selected directly by pressing XM RADIO.
16
ENGLISH
If the next [NUMBER] is not pressed within several seconds, the
channel automatically switches to the channel number that was
input.
ENGLISH
Operation
Operation
Playing the
ENTER
STATUS
MODE
MEMORY
FUNCTION
<SELECT>
<ON/STANDBY>
iPod®
Listening to music
The music recorded on the iPod can be played when using a Control
Dock for iPod (ASD-1R, sold separately). The iPod can be controlled
using the buttons on the main unit and the remote control unit.
the DRA-697CI and iPod using the Control
1 Connect
Dock for iPod (ASD-1R) (
page 9).
iPod is a trademark of Apple Computer, Inc., registered
in the U.S. and other countries.
the input terminal at “Setting the iPod
2 Assign
Assignment” (
page 11).
With the iPod, non-copyrighted contents and contents that may be
legally reproduced or played may be reproduced and played by
individuals for their personal use. Violating copyrights is prohibited
by law.
3 Use FUNCTION to select the function assigned in step 2.
MENU
• The optional standard Control Dock for iPod is DENON ASD-1R sold
separately.
• To assign to a different function after a function has already been
assigned, switch to a function other than the one that is assigned
then repeat the procedure.
[POWER OFF]
• Display “Remote iPod” on the main unit’s display.
Remote iPod
If the screens above are not displayed, the iPod may not be
properly connected. Check the connections and settings.
D H F G] and
using MENU, <SELECT>, [D
4 Operate
ENTER while watching the iPod’s screen.
FUNCTION
MENU
STATUS
FUNCTION
ENTER
[D H F G]
NOTE:
• DENON will accept no responsibility whatsoever for loss or
damage of data on an iPod occurring when the iPod is used
connected to the DRA-697CI.
• Some of the functions may not operate, depending on the type
of iPod and the software version.
MODE
MEMORY
About the button names in this explanation
<
> : Buttons on the main unit
[
] : Buttons on the remote control unit
Button name only :
Buttons on the main unit and remote control unit
17
ENGLISH
• The optional standard Control Dock for iPod is DENON ASD-1R sold
separately.
ENGLISH
Operation
Operation
Listening to music in the Browse mode
The mode switches between the Remote mode and the Browse
mode if MODE is pressed for at least 2 seconds.
D H] to select the music file,
Use <SELECT> or press [D
1 then
G].
press ENTER or [G
F] to return to the music menu screen.
Press [F
2 Press ENTER or [GG].
• Playback starts.
Pause:
Press ENTER during playback.
Press again to resume.
Manual search:
D H] during playback.
Press and hold in [D
• D: Fast reverse
• H: Fast forward
Track search:
D H] during playback.
Press [D
• D: Move to beginning of previous track
• H: Move to beginning of next track
Stop:
Press ENTER for at least 2 seconds during playback.
Repeat play:
Press MODE.
The mode switches as follows each time MODE is pressed.
• Repeat One:
Single track repeat
• Repeat All:
All track repeat
Shuffle play:
Press MEMORY.
The mode switches as follows each time MEMORY is pressed.
• Shuffle Songs: Single track shuffle
• Shuffle Albums: Album shuffle
D H F G], MENU, MODE,
In the Remote mode, only <SELECT>, [D
MEMORY and ENTER can be used.
• When STATUS is pressed during playback, the front panel display
switches between the title name, artist name and album name.
• Depending on the iPod’s software version, it may not be possible to
operate the iPod from the DRA-697CI. Use the latest version of the
software. Information on the latest version of the software can be
obtained on the Apple Computer website.
• With the DRA-697CI it is possible to display folder names and file
names on the screen like titles. The DRA-697CI can display up to 64
characters, consisting of numbers, capital letters and small letters.
A “?” mark is displayed in place of non-compatible characters.
Viewing still pictures and videos (only for iPods
equipped with the slideshow/video function)
Use this procedure to view photo and video data stored on the iPod
on a monitor.
Press MODE for at least 2 seconds to switch from the
1 Browse
mode to the Remote mode.
• “Remote iPod” is displayed on the DRA-697CI’s display.
D H] to select
Watching the iPod’s screen, press [D
2 “Photos”
or “Video”, then press ENTER.
• The iPod’s photo and video data are displayed on the monitor.
• To output photo or video data recorded on the iPod to the monitor,
the iPod’s “TV Out” setting (under “Video Settings”) must be set to
“ON”.
For details, refer to the iPod’s operating instructions.
Disconnecting the iPod
Press <ON/STANDBY> or [POWER OFF] and set the
DRA-697CI’s power to the standby mode.
The iPod can be disconnected after switching to a function other
than the one to which the iPod input is assigned.
18
ENGLISH
ENGLISH
Operation
Operation
Multi zone music entertainment system
• When the outputs of the ZONE2 (ZONE3) OUT terminals are wired and connected to power amplifiers installed in other rooms, different
sources can be played in rooms other than the MAIN ZONE in which this unit and the playback devices are installed. (Refer to ZONE2
(ZONE3) on the diagram below.)
• When a sold separately room-to-room remote control unit is wired and connected between the MAIN ZONE and ZONE2 (ZONE3), the
remote-controllable devices in the MAIN ZONE can be controlled from ZONE2 (ZONE3) using the remote control unit.
To control playback devices other than the ones above, either use that device’s remote control unit or preset a separately sold programmable
remote control unit.
• For instructions on installation and operation of separately sold devices, refer to the devices’ operating instructions.
Multi-zone playback using the ZONE2 and ZONE3 PREOUT terminals
¢ When using the power amplifier as the MAIN ZONE output
• The DRA-697CI is equipped with pre-out terminals for which the volume is adjustable and video output terminals (composite) as the ZONE2
(ZONE3) output terminals, and variable output level as the ZONE2 (ZONE3) output terminals.
[System configuration and connections example]
Using external amplifier.
ZONE2
MAIN ZONE 2.1-channel system
Monitor
Monitor
ZONE3
ZONE3
video out
Monitor
ZONE2
video out
FL
FR
DRA-697CI
DVD player
SW
Power
Amplifer
Power
Amplifer
B
B
Input
ZONE2 audio out
(Variable out)
System remote
control unit (RC-1052)
ZONE
remote control unit
(RC-1056)
ZONE remote
control unit
(RC-1056)
ZONE3 audio out (Variable out)
: Multi source video signal cable
: Multi source audio signal cable
: Room-to-room remote control system
(separately sold) control line
Refer to “Connections” (
page 9).
19
ENGLISH
ENGLISH
Operation
Operation
Outputting a program source to amplifier, etc.,
in the ZONE2 (or ZONE3) room (ZONE2 or
ZONE3 SELECT mode)
FUNCTION
1
Press <ZONE/REC SELECT> to select “M-ZONE”.
RECOUT
M-ZONE
Remote control unit operations during multisource playback
1 Set [MODE SELECTOR 1] to the “B”.
Set [MODE SELECTOR 2] to the
2 “ZONE3”.
“ZONE2” or
Use FUNCTION to select the source you want to
2 output
3 Press [ZONE2 (ZONE3) ON] to turn on the zone power.
appears on the display.
• The “
” indicator and the indicator for the selected
source light.
<ZONE/REC SELECT>
[CHANNEL]
FUNCTION
3 Start playing the source to be output.
For operating instructions, refer to the manuals of the respective
components.
[VOLUME]
• The signals of the source selected in the ZONE mode are also
output from the VCR and CD-R/TAPE recording output terminals.
To cancel the ZONE2 or ZONE3 mode:
Press [ZONE2 OFF] or [ZONE3 OFF].
[FUNCTION] to select the input source you wish
4 Use
to output.
• The “
” indicator and the indicator for the selected
source light.
The MULTI ZONE source switches directly.
When the MULTI ZONE SOURCE function is set to “FM/AM”,
the preset channel can be selected pressing [CHANNEL].
volume of the outputs of the different zones can
5 The
be adjusted with [VOLUME].
[MODE SELECTOR 1]
[ZONE2 ON]
[ZONE2 OFF]
Default volume setting
ZONE2/ZONE3 :
– – – dB (Minimum)
The zone volume can be adjusted within the range of –80 to 18
dB, in steps of 0.5 dB.
[MODE SELECTOR 2]
[ZONE3 OFF]
[ZONE3 ON]
• When using ZONE2 or ZONE3, it is possible to turn the power for
the MAIN ZONE only on or off by pressing [MAIN ON/OFF].
FUNCTION
[MAIN ON/OFF]
About the button names in this explanation
<
> : Buttons on the main unit
[
] : Buttons on the remote control unit
Button name only :
Buttons on the main unit and remote control unit
20
ENGLISH
ENGLISH
Operation
Operation
Recording (audio and/or video)
FUNCTION
<ZONE/REC SELECT>
1
Press <ZONE/REC SELECT> until “RECOUT”
appears on the display.
RECOUT
M-ZONE
FUNCTION to select the source to be recorded
2 Use
(audio and/or video).
• The “
” indicator lights.
3 Record (the audio or video signals).
<POWER>
<SPEAKER A, B>
For operations, see the operating instructions of the device from
which you are recording (audio or video signals).
About the memory functions
¢ Last function memory
The various settings set when the DRA-697CI’s power is switched to
standby are stored in the memory. When the power is turned back on,
the settings made when the power was switched to standby are
recalled.
¢ Backup memory
The various settings are stored in the memory for about 1 week, even
when the power is turned off or the power cord is unplugged.
Initialization of the microprocessor
If the indication on the display is not normal or if the operation of the
unit is not correct, then the microprocessor should be reset by the
following procedure.
• To cancel, press <ZONE/REC SELECT> and set the function to “ZONE”.
FUNCTION
[MODE SELECTOR 1]
[MODE SELECTOR 2]
NOTE:
• When the REC OUT mode is selected, FUNCTION (ZONE) cannot
be operated.
1 Switch off the unit using <POWER>.
and hold in <SPEAKER A>, <SPEAKER B> and
2 Press
<POWER> simultaneously until “PLEASE WAIT” is
displayed.
• The microprocessor will be initialized.
[ZONE2 OFF]
[ZONE3 ON]
• If step 2 does not work, start over from step 1.
• If the microprocessor has been reset, all the button settings are
reset to the default values (the values set upon shipment from the
factory).
[NUMBER]
(0 ~ 9, +10)
[A]
[D]
FUNCTION
About the button names in this explanation
<
> : Buttons on the main unit
[
] : Buttons on the remote control unit
Button name only :
Buttons on the main unit and remote control unit
21
ENGLISH
ENGLISH
Operating the remote control unit
Operating DENON audio components
to the included list of preset codes, press
4 Referring
[NUMBER] to input the preset code (a 3-digit number)
Setting the punch through function
“Punch Through” is a function allowing you to operate 1, 2, 0, 3,
6, 7, 8 and 9 on CD, DVD/VDP, TAPE/CD-R/MD or VCR
components when in the TV or DBS/CABLE mode. By default, nothing
is set.
1
[MODE SELECTOR 2] to the position for the
2 Set
store the codes of another component in the
component to be operated.
5 Tomemory,
repeat steps 1 to 4.
1 Set [MODE SELECTOR 1] to “A”.
3 Operate the audio component.
[MODE SELECTOR 2] to the component to be
2 Set
registered (TV or DBS/CABLE).
Set [MODE SELECTOR 1] to “A” or “B”.
For details, refer to the component’s operating instructions.
While this remote control is compatible with a wide range of
infrared controlled components, it may be the case that some
component models cannot be operated with this remote control.
Setting the preset memory function
• DENON and other makes of components can be operated by setting
the preset memory.
• This remote control unit can be used to operate components of
other manufacturers without using the learning function by
registering the manufacturer of the component as shown in the list
of preset codes (
End of this manual).
• Operation is not possible for some models.
for the manufacturer of the component whose signals
you want to store in the memory.
• The signals for the pressed buttons are emitted while setting the
preset memory. To avoid accidental operation, cover the remote
control unit’s transmitting window while setting the preset memory.
• Depending on the model and year of manufacture, this function
cannot be used for some models, even if they are of makes listed in
the list of preset codes.
• Some manufacturers use more than one type of remote control
code. Refer to the included list of preset codes to change the
number and verify correct operation.
• The preset memory can be set for one component only among the
following: CD/iPod, DBS/CABLE and CD-R/TAPE.
1 Set [MODE SELECTOR 1] to “A” or “B”.
3 Press [A] and [D] at the same time.
• The indicator starts flashing.
4 Input the number of the component you want to set.
CD
DVD/VDP
TAPE/CD-R/MD
VCR
No setting
No.
1
2
3
4
0
Operating a component stored in the preset
memory
Set to the A side for the CD/iPod, TV, DBS/CABLE or DVD
position, and to the B side for the CD-R/TAPE or VCR position.
[MODE SELECTOR 2] to the component to be
2 Set
registered.
1 Set [MODE SELECTOR 1] to “A” or “B”.
Set to the A side for the CD/iPod, TV, DBS/CABLE or DVD
position, and to the B side for the CD-R/TAPE or VCR position.
3 Press [ZONE2 OFF] and [ZONE3 ON] at the same time.
• The indicator starts flashing.
[MODE SELECTOR 2] to the component you want
2 Set
to operate.
3 Operate the component.
For details, refer to the component’s operating instructions.
Some models cannot be operated with this remote control unit.
22
ENGLISH
ENGLISH
Operating the remote control unit
Operating the remote control unit
¢ Functions of buttons for the different devices
[Front]
Device operated
CD player or iPod
TV
(Monitor)
Satellite tuner
Cable TV
DVD player
CD recorder
Tape deck
Video deck
B
A
MODE SELECTOR 1
MD recorder
CD-R/TAPE
VCR
MODE SELECTOR 2
CD/iPod
TV
OFF
Power off
–
–
–
Power off
Power off
Power off
Power off
–
ON
Power on
Power on
Power on
Power on
Power on
Power on
Power on
Power on
Power on
CHANNEL –
Preset –
TV channels –
Channels –
Channels –
Preset –
Preset –
Preset –
Preset –
TV channels –
CHANNEL +
Preset +
TV channels +
Channels +
Channels +
Preset +
Preset +
Preset +
Preset +
TV channels +
1
Play
Punch through
Punch through
Punch through
Play
Play
Forward play
Play
Play
2
Stop
Punch through
Punch through
Punch through
Stop
Stop
Stop
Stop
Stop
3, A/B
Pause
Punch through
Punch through
Punch through
Pause
Pause
A/B switching
Pause
Pause
0, SKIP +
Disc skip +
Punch through
Punch through
Punch through
Disc skip +
–
Reverse play
–
–
6
Search (reverse)
Punch through
Punch through
Punch through
Search (reverse)
Search (reverse)
Rewind
Search (reverse)
Search (reverse)
7
Search (forward)
Punch through
Punch through
Punch through
Search (forward)
Search (forward)
Fast forward
Search (forward)
Search (forward)
8, VCR CH –
Skip (reverse)
Punch through
Punch through
Punch through
Skip (reverse)
Skip (reverse)
–
Skip (reverse)
Channel –
9, VCR CH +
Skip (forward)
Punch through
Punch through
Punch through
Skip (forward)
Skip (forward)
–
Skip (forward)
Channel +
MENU
Menu
Menu
Menu
Menu
Top menu
Menu
Menu
Menu
–
DHFG
Cursor operation
Cursor operation
Cursor operation
Cursor operation
Cursor operation
Cursor operation
Cursor operation
Cursor operation
–
DIMMER
Dimmer
Dimmer
Dimmer
Dimmer
Menu
Dimmer
Dimmer
Dimmer
Dimmer
ENTER
Enter
Enter
Enter
Enter
Enter
Enter
Enter
Enter
–
STATUS
Status
Display
Display
Display
Display
Status
Status
Status
–
VIDEO SELECT
Video selection
Return
Return
Return
Return
Video selection
Video selection
Video selection
–
PURE DIRECT
Pure direct
Pure direct
Pure direct
Pure direct
Set up
Pure direct
Pure direct
Pure direct
Pure direct
DBS/CABLE
DVD
23
ENGLISH
ENGLISH
Operating the remote control unit
Operating the remote control unit
[Rear]
Device operated
CD player or iPod
TV
(Monitor)
MODE SELECTOR 1
Satellite tuner
Cable TV
DVD player
CD recorder
Tape deck
A
MD recorder
Video deck
B
MODE SELECTOR 2
CD/iPod
TV
DBS/CABLE
NUMBER (0 ~ 9, +10)
Channels
Channels
Channels
Channels
Channels
Channels
Channels
Channels
Channels
BAND
FM/AM switching
TV/VCR switching
TV/VCR switching
TV/VCR switching
TV/VCR switching
FM/AM switching
FM/AM switching
FM/AM switching
TV/VCR switching
A, AUDIO
Memory block
–
–
–
Audio
Memory block
Memory block
Memory block
–
B, SUBTITLE
Memory block
–
–
–
Subtitle
Memory block
Memory block
Memory block
–
C, ANGLE
Memory block
–
–
–
Angle
Memory block
Memory block
Memory block
–
D, PICT ADJ.
Memory block
–
–
–
Picture adjust
Memory block
Memory block
Memory block
–
E, S.MODE
Memory block
–
–
–
Search mode
Memory block
Memory block
Memory block
–
TUNING +
Tuning +
TV volume +
Volume +
Volume +
TV volume +
Tuning +
Tuning +
Tuning +
TV volume +
TUNING –
Tuning –
TV volume –
Volume –
Volume –
TV volume –
Tuning –
Tuning –
Tuning –
TV volume –
Default setting
(Preset code)
DENON
(111)
HITACHI
(134)
–
ABC
(007)
DENON
(111)
–
DENON
(114)
–
HITACHI
(108)
Special remarks
q
q, e
q, e
DVD
q, w
Special remarks:
q It is only possible to set the preset memory for one device per mode. When a new code is preset, the previous code is automatically deleted.
w Note that the function names of the DVD buttons on the remote control unit may differ for some brands. Check beforehand.
e The CD, TAPE/CD-R/MD, VCR or DVD/VDP buttons can be assigned to a TV or satellite tuner (or cable TV) (
page 22).
24
ENGLISH
VCR
CD-R/TAPE
q
q
ENGLISH
Troubleshooting
Symptom
Troubleshooting
This unit does not
operate properly when
remote control unit is
used.
If a problem should arise, first check the following.
1. Are the connections correct?
2. Have you operated the receiver according to the Operating Instructions?
3. Are the speakers and other components operating properly?
If this unit is not operating properly, check the items listed in the table below. Should the problem persist,
there may be a malfunction. Disconnect the power immediately and contact your store of purchase.
Symptom
Cause
Measures
Display not lit and sound
not produced when
POWER switch set to
on.
• Power supply cord not plugged in • Check the insertion of the power
securely.
supply cord plug.
Display lit but sound not
produced.
• Speaker
cables
not
securely
connected.
• FUNCTION knob position is not
appropriate.
• Volume control set to minimum.
• MUTING is on.
Nothing is displayed on
monitor.
6
• Switch to the proper position.
12
• Turn volume up to suitable level.
• Switch off MUTING.
12
12
6
—
Copying from DVD to
VCR is not possible.
• Copying between a source such as • Copying is not possible.
DVD and a VCR is not usually
possible, as DVDs are often encoded
with copy-protection signals that
prevent VCR recording.
—
No sound is produced
from subwoofer.
• Subwoofer’s power is not on.
• Turn on the power.
• Subwoofer’s output is not connected. • Connect properly.
• The subwoofer’s channel volume • Turn the subwoofer’s channel volume
level is set to “–12 dB”.
level up.
—
6
13
• Batteries dead.
• Remote control unit too far from this
unit.
• Obstacle between this unit and
remote control unit.
• Different button is being pressed.
• < and > ends of batteries inserted
in reverse.
Measures
Page
• Replace with new batteries.
• Move closer.
2
2
• Remove obstacle.
—
• Press the proper button.
• Insert batteries properly.
—
2
• The set’s internal temperature has • Put the DRA-697CI in a wellventilated place.
risen and the protection circuit has
• Turn off the power, then wait for the
been activated.
set to fully cool off before turning the
power back on.
• The core wires of the speaker cables • Check the connections of all the
speaker cables.
are touching each other or the DRA697CI’s rear panel, activating the
protection circuit.
• Turn off the power and contact a
• DRA-697CI is malfunctioning.
DENON customer service center.
2, 6
“CHECK ANTENNA” is
displayed in the XM
mode.
• DRA-697CI’s XM connectors and the • Check that the connection are
XM Mini-Tuner and Home Dock is not
correct.
properly connected.
8
“NO SIGNAL” is
displayed in the XM
mode.
• The signal cannot be received.
“OFF AIR” is displayed
in the XM mode.
• The selected channel is not currently • Select the another channel.
broadcasting.
Receiving only XM
channels 0 and 1.
• The XM Tuner is not activated.
10
• Connect securely.
• DRA-697CI’s video output terminals • Check that the connections are
correct.
and monitor’s input terminals are not
properly connected.
• Monitor’s input setting is wrong.
• Set the monitor’s input selector to
the terminals to which video signals
are connected.
Power has turned off
and the power indicator
is blinking red.
Page
Cause
25
ENGLISH
• Reposition your XM Mini-Tuner and
Home Dock.
• Contact XM Radio.
6
6
6
8, 15
16
8, 15
ENGLISH
Specifications
¢ Audio section
• Power amplifier
Rated output:
Output terminals:
• Analog
(LINE input-PRE OUT)
Input sensitivity / input impedance:
Frequency response:
S/N:
Total harmonic distortion:
Rated output:
100 W + 100 W (8 Ω/ohms, 20 Hz ~ 20 kHz with 0.08 % T.H.D.)
A or B
4 ~ 16 Ω/ohms
A+B
8 ~ 16 Ω/ohms
200 mV / 47 kΩ/kohms
10 Hz ~ 100 kHz: +1, –3 dB (TONE DEFEAT ON)
98 dB (IHF-A weighted) (TONE DEFEAT ON)
0.009 % (–3 dB at rated output) (1 kHz)
1.2 V
¢ Video section
• Standard video terminals
Input / output level and impedance:
Frequency response:
1 Vp-p, 75 Ω/ohms
5 Hz ~ 10 MHz — +1, –3 dB
¢ Tuner section
Receiving Range:
Usable Sensitivity:
50 dB Quieting Sensitivity:
S/N (IHF-A):
Total Harmonic Distortion (at 1 kHz):
[FM]
(note: µV at 75 Ω/ohms, 0 dBf = 1 x 10–15 W)
87.5 MHz ~ 107.9 MHz
1.0 µV (11.2 dBf)
MONO
1.6 µV (15.3 dBf)
STEREO
23 µV (38.5 dBf)
MONO
77 dB (IHF-A weighted)
STEREO
72 dB (IHF-A weighted)
MONO
0.15 %
STEREO
0.3 %
[AM]
520 kHz ~ 1710 kHz
18 µV
¢ General
Power supply:
Power consumption:
Maximum external dimensions:
Mass:
AC 120 V, 60 Hz
4.2 A
1 W Max (Standby)
434 (W) x 171 (H) x 417 (D) mm (17-3/32” x 6-47/64” x 16-27/64”)
10.5 kg
¢ Remote control unit (RC-1052)
Batteries:
External dimensions:
Mass:
R6P/AA Type (Two batteries)
52 (W) x 243 (H) x 21 (D) mm (2-3/64” x 9-9/16” x 53/64”)
175 g (Approx. 6.2 oz) (included batteries)
¢ ZONE remote control unit (RC-1056)
Batteries:
External dimensions:
Mass:
R03/AAA Type (Two batteries)
54 (W) x 115 (H) x 23 (D) mm (2-1/8” x 4-17/32” x 29/32”)
80 g (Approx. 2.8 oz) (included batteries)
* For purposes of improvement, specifications and design are subject to change without notice.
26
ENGLISH
ENGLISH
¢ List of preset codes
DVD
ASA
042
Go Video
047, 048
Minolta
013, 023
Denon
014, *[111]
Asha
087
Goldstar
000, 006, 012, 062, 088
Mitsubishi
001, 003, 008, 013, 014,
Aiwa
009
Audio Dynamic
005, 085
Gradiente
094
Hitachi
010
Audiovox
088
Grundig
042
JVC
006, 011
Beaumark
087
Harley Davidson
094
Motorola
Konka
012, 013
Broksonic
086, 093
Harman Kardon
040, 062
Montgomery Ward
Magnavox
005
Calix
088
Hi-Q
091
Mitsubishi
004
Candle
006, 087, 088, 089, 090
Hitachi
Panasonic
014
Canon
049, 057
Philips
005, 015, 016, 017
Capehart
025, 055, 056, 071
Pioneer
003, 008
Carver
015
Sanyo
018
CCE
095
Sony
002, 019, 020
Citizen
006, 007, 087, 088, 089,
Toshiba
001, 021, 022
Zenith
023
JC Penny
007, 087, 088, 091, 115
Curtis Mathes
006, 049, 073, 080, 087,
VDP
009, 013, 023, 026, 058,
MTC
009, 087, 094
Multitech
007, 009, 011, 087, 090,
004, 005, 007, 023, 028,
094
013, 026
NEC
JVC
004, 005, 006, 026, 029,
038
004, 005, 006, 018, 026,
029, 045, 061, 062, 085
043, 044, 045, 046, 085
Nikko
088
004, 005, 006, 026, 029,
Noblex
087
033, 045, 085, 090
Optimus
081, 088
090, 092
Kodak
088
Optonica
021
087
Lloyd
009, 094
Panasonic
024, 049, 064, 066, 067,
025, 055, 059, 074, 089,
LXI
088
093, 095, 096
Magnavox
015, 016, 042, 049, 063,
Perdio
009
106
Pentax
009, 013, 023, 058, 090
087
Philco
015, 016, 049
Cybernex
Magnavox
026
Daewoo
Mitsubishi
028
Panasonic
029, 030
Daytron
025, 055
Philips
026
DBX
005, 085
Magnin
Pioneer
028, 031
Dumont
053
Marantz
RCA
032
Dynatech
009
Sony
033, 034, 035, 036
Electrohome
001, 088, 097
Electrophonic
088
Emerson
001, 009, 017, 027, 086,
VCR
001, 002, 007, 009, 049,
*[108], 109, 110, 111
Jensen
Kenwood
081
063, 081, 115, 117
NAD
028, 029, 112
Denon
041, 045, 097
049, 062, 085, 087, 088
090, 095
Craig
017, 027, 029, 039, 040,
068, 069, 107
004, 005, 006, 015, 042,
Philips
015, 021, 042, 049, 105
049, 085, 090
Pilot
088
Marta
088
Pioneer
MEI
049
Memorex
009, 033, 049, 053, 060,
Portland
005, 013, 029, 036, 037,
038, 045, 085
025, 055, 090
Admiral
081
088, 089, 092, 093, 097,
081, 087, 088, 091, 094,
Proscan
063, 080
Aiko
095
100, 101, 102, 103, 104,
115
Pulsar
060
Aiwa
009
Akai
026, 027, 070, 072, 082,
117
Fisher
083, 084
Alba
055
Amstrad
009
GE
Metz
009, 028, 031, 053, 054,
123, 124, 125, 126, 127,
Quartz
033
128
Quasar
034, 035, 049
Radio Shack
091, 099, 115
MGA
001, 017, 027, 041, 097
007, 011, 049, 050, 051,
MGN Technology
087
088, 091, 094, 097, 098,
052, 073, 080, 087
Midland
011
115
1
PRESET CODE
001, 002, 021, 081, 087,
ENGLISH
Radix
088
Technics
024, 049
Bell & Howell
045, 118
Fujitsu
004, 062
Randex
088
Teknika
009, 010, 022, 049, 088,
Bradford
061
Funai
004, 062
RCA
Realistic
094
Brockwood
003, 047
Futuretech
004
063, 064, 065, 073, 080,
TMK
087, 092
Candle
003, 030, 031, 032, 038,
GE
020, 036, 037, 040, 044,
082, 087
Toshiba
013, 017, 020, 041, 059,
007, 013, 019, 023, 058,
047, 049, 050, 122
058, 066, 088, 119, 120,
089, 098, 099, 117
Capehart
003
007, 087, 088
Celebrity
046
Unirech
087
Circuit City
003
048, 051, 056, 057, 067,
Vecrtor Research
005, 062, 085, 089, 090
Citizen
029, 030, 031, 032, 034,
068, 069, 116
009, 021, 031, 033, 049,
125, 147
053, 081, 087, 088, 091,
Totevision
094, 097, 098
055
Salora
033, 041
Victor
005, 045, 046, 085
038, 047, 049, 050, 054,
Grundy
062
Samsung
007, 011, 051, 059, 070,
Video Concepts
005, 027, 085, 089, 090
061, 095, 122, 123
Hitachi
029, 031, 051, 052, 070,
083, 087, 089, 113
Videosonic
007, 087
Concerto
031, 047, 049
111, 112, 113, 124,
081
Wards
013, 021, 023, 087, 088,
Colortyme
003, 047, 049, 135
*[134]
005, 026, 029, 045, 061,
089, 091, 094, 097, 118,
Contec
013, 051, 052, 061
Hitachi Pay TV
151
085, 114
119, 120
Cony
051, 052, 061
Infinity
017, 071
094
Craig
004, 061
Janeil
122
004, 005, 006, 026, 062,
Crown
029
JBL
017, 071
085
Curtis Mathes
029, 034, 038, 044, 047,
JC Penny
020, 034, 039, 040, 041,
Ricoh
Sanky
Sansui
Sanyo
SBR
Scott
032, 033, 053, 087, 091,
XR-1000
115, 116
Yamaha
042
017, 020, 086, 089, 093,
Zenith
060, 078, 079
Daewoo
117
013, 023, 028, 031, 033,
TV
053, 054, 088, 091, 098,
Admiral
099, 115
055
Sharp
001, 002, 021, 097
Shogun
087
Sears
Sentra
Sony
STS
Sylvania
Goldstar
000, 015, 029, 031, 039,
049, 053, 095, 118
044, 048, 050, 058, 066,
027, 029, 039, 048, 049,
069, 076, 088, 090, 095,
125, 136, 159
054, 055, 106, 107, 137
003, 049
JCB
Dimensia
044
JVC
Dixi
007, 015, 027
016, 027, 046
Electroband
046
Kawasho
018, 046
062
Electrohome
029, 056, 057, 058, 147
Kenwood
038, 056, 057
045, 121
Daytron
Adventura
122
Aiko
054
Akai
Alleron
046
019, 051, 052, 072, 073,
091, 117, 126
075, 076, 077, 078, 079,
A-Mark
007
Elta
027
Kloss
010, 032
121, 122
Amtron
061
Emerson
029, 051, 059, 060, 061,
Kloss Novabeam
005, 122, 127, 131
023
Anam
006, 007, 036
062, 118, 123, 124, 139,
KTV
074, 123
009, 015, 016, 017, 041,
Anam National
061, 147
148
Loewe
071
049, 094
AOC
003, 007, 033, 038, 039,
Envision
038
Logik
144
047, 048, 049, 133
Etron
027
Luxman
031
007
Fisher
014, 021, 063, 064, 065,
LXI
008, 014, 017, 024, 040,
Symphonic
009, 094
Tandy
009
Archer
Tashiko
009, 088
Audiovox
007, 061
118
044, 063, 071, 075, 076,
Tatung
004, 026, 030
Bauer
155
Formenti
155
077, 118, 125
Teac
004, 009, 026, 094
Belcor
047
Fortress
012
2
PRESET CODE
ENGLISH
Magnavox
005, 010, 017, 030, 033,
Philips
038, 050, 056, 071, 078,
005, 015, 017, 050, 051,
Squareview
004
Eastern
015
056, 078, 087, 088, 089,
Supre-Macy
032, 122
Garrard
011
131, 132, 147
Supreme
046
Gemini
030, 033, 034
110, 127, 131, 132, 145
Pioneer
124, 128, 142
Sylvania
005, 010, 017, 030, 078,
General Instrument
030, 031, 032
015, 017, 071, 080
Portland
054
079, 085, 089, 101, 127,
Hytex
006
Matsui
027
Price Club
095
131, 132, 145, 155
Jasco
011
Memorex
014, 027, 045, 083, 118,
Proscan
040, 044, 125
Symphonic
004, 148
Jerrold
009, 016, 017, 026, 032
144
Proton
035, 051, 092, 129
Tandy
012, 121
Magnavox
018
Metz
160, 161, 162, 163
Pulsar
042
Tatung
036, 124
Movie Time
019
MGA
001, 039, 048, 056, 057,
Quasar
036, 037, 074, 141
Technics
037
NSC
019
058, 065, 081, 083
Radio Shack
011, 044, 063, 093, 118
Teknika
001, 030, 032, 034, 052,
Oak
000, 006, 020
Midland
125
RCA
040, 044, 125, 130, 137,
054, 078, 083, 095, 144,
Panasonic
001, 005
Minutz
066
151, 152
156, 157
Philips
011, 012, 013, 018, 021
079, 085, 089, 108, 109,
Marantz
Mitsubishi
001, 016, 039, 048, 056,
Realistic
014, 063, 093, 118
Tera
035, 129
Pioneer
002, 003, 022
057, 058, 065, 081, 082,
Saisho
027
THOMSON
165, 166
RCA
029
083, 105
Samsung
003, 015, 034, 053, 055,
Toshiba
015
008, 014, 034, 063, 075,
Regency
057, 094, 095, 136, 153
076, 095, 097, 136, 158,
Samsung
014, 023
159
Scientific Atlanta
004, 024, 025
Montgomery Ward
011, 020, 144, 145, 146
Motorola
121, 147
Sansui
139
MTC
031, 034, 039, 048, 095
Sanyo
013, 014, 021, 022, 063,
Universal
020, 066, 088
Signal
014
NAD
008, 075, 076, 128
064, 081, 096
Victor
019, 073, 126
SL Marx
014
015
Video Concepts
016
Starcom
009
015
Viking
032, 122
Stargate
014
Wards
National
002, 036, 061, 147
SBR
National Quenties
002
Schneider
031, 038, 039, 048, 057,
Scott
062
084, 086, 135, 147
Sears
008, 014, 021, 022, 023,
NEC
Nikko
054
024, 025, 040, 052, 057,
NTC
054
062, 063, 064, 065, 073,
Optimus
128
075, 076, 097, 098, 125,
Optonica
011, 012, 093, 121
159
Orion
004, 139
Panasonic
Philco
Sharp
002, 009, 017, 036, 037,
Zenith
Zonda
005, 045, 066, 078, 085,
Teleview
014
088, 089, 093, 102, 103,
Tocom
007, 016
131, 132, 148
TV86
019
042, 114, 115, 140, 144,
Unika
011
149
United Artists
006
007
Universal
010, 011
Viewstar
018, 019
Zenith
027, 028
011, 012, 013, 026, 093,
099, 100, 104, 121
CABLE
071, 141, 143, 147
Siemens
013
ABC
006, *[007], 008, 009
005, 010, 030, 050, 051,
Signature
045, 144
Archer
010, 011
DBS (SATELLITE)
056, 079, 085, 127, 131,
Simpson
050
Century
011
Alphastar
054
132, 145, 147
Sony
043, 046, 138, 146, 150
Citizen
011
Chaparral
035, 036
Soundesign
030, 050, 062
Colour Voice
012, 013
Dishnet
053
Spectricon
007, 033
Comtronic
014
Drake
037, 038
3
PRESET CODE
ENGLISH
062, 066
Magnavox
006, 015, 035
Optimus
016, 017
GE
048, 055, 056
Marantz
016, 028, 035
Panasonic
021
General Instruments
039, 040, 041
MCS
016, 024
Philips
011
Grundig
070, 071, 072, 073
Onkyo
025, 027
Pioneer
016, 017, 018
Hitachi
058, 059
Optimus
017, 020, 021, 022, 023
Sony
022, 023, 024
Hughes Network
063, 064, 065, 069
Philips
014, 032, 033, 035
Technics
021
JVC
057
Pioneer
006, 022, 030
Victor
013
Kathrein
074, 075, 076, 083
Sears
006
Wards
016
Magnavox
060
Sony
023, 031
Yamaha
019, 020
Nokia
070, 080, 084, 085, 086
Teac
002, 009, 028
Philips
060
Technics
016, 029, 036
Primestar
051
Wards
035, 037
Proscan
048, 055, 056
Yamaha
038, 039, 040, 041
RCA
048, 055, 056, 068
Zenith
042
Realistic
042
Sierra I
036
Sierra II
036
Denon
*[111], 112
Sierra III
036
Philips
112
Sony
049, 067
STS1
043
MD
STS2
044
Denon
113
STS3
045
Kenwood
003, 004
SRS4
046
Onkyo
007
Technisat
077, 078, 079, 081, 082
Sharp
005
Toshiba
047, 050
Sony
006
Uniden
061
*[ ] : Preset codes set upon shipment from the
factory.
CDR
TAPE
CD
Denon
*[114]
*[111], 044
Aiwa
010, 011
Aiwa
001, 035, 043
Carver
011
Burmster
002
Harman/Kardon
011, 012
Carver
003, 035
JVC
013, 014
Emerson
004, 005, 006, 007
Kenwood
015
Fisher
003, 008, 009, 010
Magnavox
011
JVC
018, 019
Marantz
011
Kenwood
011, 012, 013, 014, 017
Onkyo
025, 027
Denon
4
PRESET CODE
DVD preset codes
111 (default)
DENON Model No.
Echostar Dish
DVD-555
DVD-755
DVD-900
DVD-910
DVD-955
DVD-1000
DVD-1200
DVD-1500
DVD-1710
DVD-1910
DVD-2200
DVD-2800
DVD-2800II
DVD-2900
DVD-2910
DVD-3800
DVD-3910
DVD-5900
DVD-5910
DVD-9000
DVM-715
DVM-1800
DVM-1805
DVM-1815
DVM-2815
DVM-4800
014
DVD-800
DVD-1600
DVD-2000
DVD-2500
DVD-3000
DVD-3300
TOKYO, JAPAN
www.denon.com
Denon Brand Company, D&M Holdings Inc.
Printed in China 00D 511 4538 007