Download Extron electronics IN1128 User`s manual

im Vertrieb von
CAMBOARD Electronics
User’s Manual
CAUTION
Do not connect this device to a computer data or
telecommunications network
TP Transmitters and Receivers
www.extron.com
Extron Electronics, USA
Extron Electronics, Europe
Extron Electronics, Asia
Extron Electronics, Japan
1230 South Lewis Street
Anaheim, CA 92805
USA
714.491.1500
Fax 714.491.1517
Beeldschermweg 6C
3821 AH Amersfoort
The Netherlands
+31.33.453.4040
Fax +31.33.453.4050
135 Joo Seng Road, #04-01
PM Industrial Building
Singapore 368363
+65.6383.4400
Fax +65.6383.4664
Daisan DMJ Building 6F
3-9-1 Kudan Minami
Chiyoda-ku, Tokyo 102-0074 Japan
+81.3.3511.7655
Fax +81.3.3511.7656
www.camboard.de
© 2002 Extron Electronics. All rights reserved.
Tel. 07131 911201
Fax 07131 911203
HIgh Resolution Video, Composite Video, and Stereo Audio
Twisted Pair Cable Transmission Products
68-754-01 Rev. A
Printed in the USA
12 02
[email protected]
im Vertrieb von
Precautions
Safety Instructions • English
This symbol is intended to alert the user of important
operating and maintenance (servicing) instructions
in the literature provided with the equipment.
This symbol is intended to alert the user of the
presence of uninsulated dangerous voltage within
the product's enclosure that may present a risk of
electric shock.
Caution
Read Instructions • Read and understand all safety and operating
instructions before using the equipment.
Retain Instructions • The safety instructions should be kept for future
reference.
Follow Warnings • Follow all warnings and instructions marked on the
equipment or in the user information.
Avoid Attachments • Do not use tools or attachments that are not
recommended by the equipment manufacturer because they may be
hazardous.
Consignes de Sécurité • Français
Ce symbole sert à avertir l’utilisateur que la
documentation fournie avec le matériel contient des
instructions importantes concernant l’exploitation
et la maintenance (réparation).
Ce symbole sert à avertir l’utilisateur de la présence
dans le boîtier de l’appareil de tensions dangereuses
non isolées posant des risques d’électrocution.
Attention
Lire les instructions• Prendre connaissance de toutes les consignes de
sécurité et d’exploitation avant d’utiliser le matériel.
Conserver les instructions• Ranger les consignes de sécurité afin de
pouvoir les consulter à l’avenir.
Respecter les avertissements • Observer tous les avertissements et
consignes marqués sur le matériel ou présentés dans la documentation
utilisateur.
Eviter les pièces de fixation • Ne pas utiliser de pièces de fixation ni
d’outils non recommandés par le fabricant du matériel car cela
risquerait de poser certains dangers.
Sicherheitsanleitungen • Deutsch
Dieses Symbol soll dem Benutzer in der im
Lieferumfang enthaltenen Dokumentation
besonders wichtige Hinweise zur Bedienung und
Wartung (Instandhaltung) geben.
Dieses Symbol soll den Benutzer darauf aufmerksam
machen, daß im Inneren des Gehäuses dieses
Produktes gefährliche Spannungen, die nicht isoliert
sind und die einen elektrischen Schock verursachen
können, herrschen.
Achtung
Lesen der Anleitungen • Bevor Sie das Gerät zum ersten Mal verwenden,
sollten Sie alle Sicherheits-und Bedienungsanleitungen genau
durchlesen und verstehen.
Aufbewahren der Anleitungen • Die Hinweise zur elektrischen Sicherheit
des Produktes sollten Sie aufbewahren, damit Sie im Bedarfsfall darauf
zurückgreifen können.
Befolgen der Warnhinweise • Befolgen Sie alle Warnhinweise und
Anleitungen auf dem Gerät oder in der Benutzerdokumentation.
Keine Zusatzgeräte • Verwenden Sie keine Werkzeuge oder Zusatzgeräte,
die nicht ausdrücklich vom Hersteller empfohlen wurden, da diese eine
Gefahrenquelle darstellen können.
Instrucciones de seguridad • Español
Este símbolo se utiliza para advertir al usuario sobre
instrucciones importantes de operación y
mantenimiento (o cambio de partes) que se desean
destacar en el contenido de la documentación
suministrada con los equipos.
Este símbolo se utiliza para advertir al usuario sobre
la presencia de elementos con voltaje peligroso sin
protección aislante, que puedan encontrarse dentro
de la caja o alojamiento del producto, y que puedan
representar riesgo de electrocución.
Precaucion
Leer las instrucciones • Leer y analizar todas las instrucciones de
operación y seguridad, antes de usar el equipo.
Conservar las instrucciones • Conservar las instrucciones de seguridad
para futura consulta.
Obedecer las advertencias • Todas las advertencias e instrucciones
marcadas en el equipo o en la documentación del usuario, deben ser
obedecidas.
Evitar el uso de accesorios • No usar herramientas o accesorios que no
sean especificamente recomendados por el fabricante, ya que podrian
implicar riesgos.
www.camboard.de
CAMBOARD Electronics
Extron’s Warranty
Warning
Power sources • This equipment should be operated only from the power source
indicated on the product. This equipment is intended to be used with a main
power system with a grounded (neutral) conductor. The third (grounding) pin is
a safety feature, do not attempt to bypass or disable it.
Power disconnection • To remove power from the equipment safely, remove all
power cords from the rear of the equipment, or the desktop power module (if
detachable), or from the power source receptacle (wall plug).
Power cord protection • Power cords should be routed so that they are not likely to
be stepped on or pinched by items placed upon or against them.
Servicing • Refer all servicing to qualified service personnel. There are no userserviceable parts inside. To prevent the risk of shock, do not attempt to service
this equipment yourself because opening or removing covers may expose you to
dangerous voltage or other hazards.
Slots and openings • If the equipment has slots or holes in the enclosure, these are
provided to prevent overheating of sensitive components inside. These openings
must never be blocked by other objects.
Lithium battery • There is a danger of explosion if battery is incorrectly replaced.
Replace it only with the same or equivalent type recommended by the
manufacturer. Dispose of used batteries according to the manufacturer's
instructions.
Avertissement
Alimentations• Ne faire fonctionner ce matériel qu’avec la source d’alimentation
indiquée sur l’appareil. Ce matériel doit être utilisé avec une alimentation
principale comportant un fil de terre (neutre). Le troisième contact (de mise à la
terre) constitue un dispositif de sécurité : n’essayez pas de la contourner ni de la
désactiver.
Déconnexion de l’alimentation• Pour mettre le matériel hors tension sans danger,
déconnectez tous les cordons d’alimentation de l’arrière de l’appareil ou du
module d’alimentation de bureau (s’il est amovible) ou encore de la prise secteur.
Protection du cordon d’alimentation • Acheminer les cordons d’alimentation de
manière à ce que personne ne risque de marcher dessus et à ce qu’ils ne soient
pas écrasés ou pincés par des objets.
Réparation-maintenance • Faire exécuter toutes les interventions de réparationmaintenance par un technicien qualifié. Aucun des éléments internes ne peut être
réparé par l’utilisateur. Afin d’éviter tout danger d’électrocution, l’utilisateur ne
doit pas essayer de procéder lui-même à ces opérations car l’ouverture ou le
retrait des couvercles risquent de l’exposer à de hautes tensions et autres dangers.
Fentes et orifices • Si le boîtier de l’appareil comporte des fentes ou des orifices,
ceux-ci servent à empêcher les composants internes sensibles de surchauffer. Ces
ouvertures ne doivent jamais être bloquées par des objets.
Lithium Batterie • Il a danger d'explosion s'll y a remplacment incorrect de la
batterie. Remplacer uniquement avec une batterie du meme type ou d'un ype
equivalent recommande par le constructeur. Mettre au reut les batteries usagees
conformement aux instructions du fabricant.
Vorsicht
Stromquellen • Dieses Gerät sollte nur über die auf dem Produkt angegebene
Stromquelle betrieben werden. Dieses Gerät wurde für eine Verwendung mit
einer Hauptstromleitung mit einem geerdeten (neutralen) Leiter konzipiert. Der
dritte Kontakt ist für einen Erdanschluß, und stellt eine Sicherheitsfunktion dar.
Diese sollte nicht umgangen oder außer Betrieb gesetzt werden.
Stromunterbrechung • Um das Gerät auf sichere Weise vom Netz zu trennen,
sollten Sie alle Netzkabel aus der Rückseite des Gerätes, aus der externen
Stomversorgung (falls dies möglich ist) oder aus der Wandsteckdose ziehen.
Schutz des Netzkabels • Netzkabel sollten stets so verlegt werden, daß sie nicht
im Weg liegen und niemand darauf treten kann oder Objekte darauf- oder
unmittelbar dagegengestellt werden können.
Wartung • Alle Wartungsmaßnahmen sollten nur von qualifiziertem
Servicepersonal durchgeführt werden. Die internen Komponenten des Gerätes
sind wartungsfrei. Zur Vermeidung eines elektrischen Schocks versuchen Sie in
keinem Fall, dieses Gerät selbst öffnen, da beim Entfernen der Abdeckungen die
Gefahr eines elektrischen Schlags und/oder andere Gefahren bestehen.
Schlitze und Öffnungen • Wenn das Gerät Schlitze oder Löcher im Gehäuse
aufweist, dienen diese zur Vermeidung einer Überhitzung der empfindlichen
Teile im Inneren. Diese Öffnungen dürfen niemals von anderen Objekten
blockiert werden.
Litium-Batterie • Explosionsgefahr, falls die Batterie nicht richtig ersetzt wird.
Ersetzen Sie verbrauchte Batterien nur durch den gleichen oder einen
vergleichbaren Batterietyp, der auch vom Hersteller empfohlen wird. Entsorgen
Sie verbrauchte Batterien bitte gemäß den Herstelleranweisungen.
Extron Electronics warrants this product against defects in materials and
workmanship for a period of three years from the date of purchase. In the event of
malfunction during the warranty period attributable directly to faulty workmanship
and/or materials, Extron Electronics will, at its option, repair or replace said products
or components, to whatever extent it shall deem necessary to restore said product to
proper operating condition, provided that it is returned within the warranty period,
with proof of purchase and description of malfunction to:
USA, Canada,
South America, and
Central America:
Extron Electronics
1230 South Lewis Street
Anaheim, CA 92805, USA
Europe, Africa, and
the Middle East:
Asia:
Extron Electronics, Europe
Beeldschermweg 6C
3821 AH Amersfoort
The Netherlands
Extron Electronics, Asia
135 Joo Seng Road, #04-01
PM Industrial Bldg.
Singapore 368363
This Limited Warranty does not apply if the fault has been caused by misuse,
improper handling care, electrical or mechanical abuse, abnormal operating conditions
or non-Extron authorized modification to the product.
If it has been determined that the product is defective, please call Extron and ask for an
Applications Engineer at (714) 491-1500 (USA), 31.33.453.4040 (Europe), or 65.383.4400
(Asia) to receive an RA# (Return Authorization number). This will begin the repair
process as quickly as possible.
Units must be returned insured, with shipping charges prepaid. If not insured, you
assume the risk of loss or damage during shipment. Returned units must include the
serial number and a description of the problem, as well as the name of the person to
contact in case there are any questions.
Extron Electronics makes no further warranties either expressed or implied with
respect to the product and its quality, performance, merchantability, or fitness for any
particular use. In no event will Extron Electronics be liable for direct, indirect, or
consequential damages resulting from any defect in this product even if Extron
Electronics has been advised of such damage.
Please note that laws vary from state to state and country to country, and that some
provisions of this warranty may not apply to you.
Advertencia
Alimentación eléctrica • Este equipo debe conectarse únicamente a la fuente/tipo
de alimentación eléctrica indicada en el mismo. La alimentación eléctrica de este
equipo debe provenir de un sistema de distribución general con conductor
neutro a tierra. La tercera pata (puesta a tierra) es una medida de seguridad, no
puentearia ni eliminaria.
Desconexión de alimentación eléctrica • Para desconectar con seguridad la
acometida de alimentación eléctrica al equipo, desenchufar todos los cables de
alimentación en el panel trasero del equipo, o desenchufar el módulo de
alimentación (si fuera independiente), o desenchufar el cable del receptáculo de
la pared.
Protección del cables de alimentación • Los cables de alimentación eléctrica se
deben instalar en lugares donde no sean pisados ni apretados por objetos que se
puedan apoyar sobre ellos.
Reparaciones/mantenimiento • Solicitar siempre los servicios técnicos de personal
calificado. En el interior no hay partes a las que el usuario deba acceder. Para
evitar riesgo de electrocución, no intentar personalmente la reparación/
mantenimiento de este equipo, ya que al abrir o extraer las tapas puede quedar
expuesto a voltajes peligrosos u otros riesgos.
Ranuras y aberturas • Si el equipo posee ranuras o orificios en su caja/alojamiento,
es para evitar el sobrecalientamiento de componentes internos sensibles. Estas
aberturas nunca se deben obstruir con otros objetos.
Batería de litio • Existe riesgo de explosión si esta batería se coloca en la posición
incorrecta. Cambiar esta batería únicamente con el mismo tipo (o su equivalente)
recomendado por el fabricante. Desachar las baterías usadas siguiendo las
instrucciones del fabricante.
Tel. 07131 911201
Fax 07131 911203
[email protected]
im Vertrieb von
CAMBOARD ElectronicsQuick Start Guide — IN1124/1128/1130
Transmission System
Step 1
Turn the equipment off and disconnect the equipment from the
power source.
Step 2
If desired, rack mount the transmitter. Use the optional 1U rackmount shelf, part #IN9080, for rack mounting.
Step 3
If desired, furniture mount the receiver. Use the optional mounting
brackets, part #IN9089, to mount the receiver to any flat surface.
Step 4
Video input — Connect the VGA-UXGA RGBHV, RGBS, RGsB video
input to the 15-pin HD Input connector on the transmitter.
Step 5
Audio input — Connect a PC audio source (such as a computer or a
CD player) to the 3.5 mm mini stereo audio connector for unbalanced
audio input on the transmitter. See the figure below for wiring.
Input only analog, line level, audio signals on the audio
input connector.
Tip (Left)
Sleeve (Gnd)
Ring (Right)
Tip (Left)
Sleeve (Gnd)
Step 6
Local monitor video output — If desired, connect a local monitor or
other device to this 15-pin HD female connector on the transmitter
for a buffered output.
Step 7
Local audio output — If desired, connect the PC audio output on
this 3.5 mm stereo jack on the transmitter to local powered speakers.
Step 8
Transmitted signal cabling — Connect up to 4 or 8 Extron skew-free
A/V or CAT 5 (minimum) cables, terminated with RJ-45 connectors,
between the transmitter and all receivers. Terminate the cables in
accordance with the TIA/EIA T 568A or TIA/EIA T 568B wiring
standards. You can use either standard, but use the same standard
on both ends of the cable. See the figure on the next page for wiring.
www.camboard.de
Tel. 07131 911201
Fax 07131 911203
[email protected]
IN1124/28/30 Transmission
System • Quick Start Guide
im Vertrieb
von — IN1124/1128/1130
Quick
Start Guide
Transmission System, cont’d
CAMBOARD Electronics
Table of Contents
Chapter 1 • Introduction ....................................................... 1-1
Side
Clip Down
12345678
Pin
12345678
About this Manual ............................................................ 1-2
About the Transmitter/Receiver System .................. 1-2
RJ-45 connector
TIA/EIA T 568 A
Wire color
TIA/EIA T 568 B
Wire color
TP cable advantages .............................................................. 1-2
System distribution ................................................................ 1-2
Transmission distance ............................................................ 1-2
Signal
1 White-green
White-orange
Red/V. sync+
2 Green
Orange
Red/V. sync-
3 White-orange
White-green
Green/H. sync+
4 Blue
Blue
Blue+
5 White-blue
White-blue
Blue-
6 Orange
Green
Green/H. sync-
7 White-brown
White-brown
Mono audio +
8 Brown
Brown
Mono audio -
About the TP Transmitter/DAs ...................................... 1-3
About the TP Receiver ..................................................... 1-4
Features ................................................................................. 1-4
IN1124 TP transmitter/distribution amplifier ....................... 1-4
IN1128 TP transmitter/distribution amplifier ....................... 1-5
IN1130 TP receiver ................................................................. 1-5
Chapter 2 • Installation and Operation ......................... 2-1
Twisted Pairs
1&2
Installation Overview .......................................................... 2-2
Rack Mounting the Transmitter ..................................... 2-2
Furniture Mounting the Receiver ................................. 2-3
Transmitter Cabling .............................................................. 2-4
Transmitted Signal Cabling .............................................. 2-6
7&8
3&6 4&5
Step 9
Video outputs — Connect the desired video devices to the Output
15-pin HD connectors on each receiver.
Termination of TP cable ........................................................ 2-6
Cable testing .......................................................................... 2-7
Equalizing pair skew ............................................................. 2-8
Step 10
Audio outputs — Connect the desired audio devices, such as local
powered speakers, to these 3.5 mm jacks on each receiver. The
output is mono.
Receiver Cabling .................................................................... 2-9
Operation ................................................................................. 2-10
Troubleshooting ................................................................... 2-10
Step 11
AC power — Plug the external 9V power supply into the power
connector on the transmitter and all receivers. Plug the power
supplies into a 100 to 240VAC, 50 Hz or 60 Hz power source. Each
unit has a power LED that indicates that power is applied.
Appendix A • Reference Information ............................ A-1
Specifications ......................................................................... A-2
Included Parts ......................................................................... A-5
Suggested Accessories ....................................................... A-6
Cables/Adapters .................................................................... A-6
Alternatively, an Extron P/S 100 Universal 12VDC Power Supply can
power up to six transmitters or receivers using only one AC power
connector.
Step 12
Sharpness control — Adjust the sharpness of both output images
from each receiver by using a Tweeker or other small, flat-head,
screwdriver to adjust the control.
68-754-01 Rev. A
Printed in the USA
12 02
All trademarks mentioned in this manual are the properties of their respective
owners.
www.camboard.de
IN1124/28/30
Transmission System • Quick Start Guide
Tel. 07131 911201
Fax 07131 911203
[email protected]
IN1124/28/30 Transmission
System • Table of Contents
i
imContents,
Vertrieb von
Table of
cont’d
CAMBOARD Electronics
IN1124/IN1128/IN1130 Transmission System
1
Chapter One
Introduction
Introduction
Features
ii
www.camboard.de
IN1124/28/30
Transmission System • Table of Contents
Tel. 07131 911201
Fax 07131 911203
[email protected]
im Vertrieb
von
Introduction,
cont’d
Introduction
CAMBOARD Electronics
About this Manual
This manual documents the installation, features, and operation
of the Extron IN1124 and IN1128 TP twisted pair (TP)
transmitters/distribution amplifiers (referred to in this manual
as “transmitters” or “transmitter/DAs”) and the IN1130 TP
receiver (referred to in this manual as a “receiver”).
The transmitters and receiver are designed for CAT 5
cable. The system can be used with CAT 3 cable, but
video performance will be compromised and maximum
cable lengths and video resolutions must be decreased.
About the Transmitter/Receiver System
The Extron IN1124 and IN1128 transmitters and IN1130
receivers provide a system for long-distance distribution of
computer (RGBHV or RGBS) video and mono audio over
Extron’s skew-free A/V UTP cable or over CAT 5 unshielded
twisted pair (UTP), shielded twisted pair (STP), or foil shielded
twisted pair (FTP) cable. With adapter cables, the system can
also distribute component video or S-video and/or composite
video.
Recommended transmission ranges at 60 Hz
Video format
Maximum range
Composite video and audio
800 feet
Component video and S-video
800 feet
640 x 480
500 feet
800 x 600
400 feet
1024 x 768
350 feet
1280 x 1024
300 feet
1600 x 1280
250 feet
TP cable advantages
Extron’s skew-free cable or CAT 5 cable is a fraction of the size
of coaxial cable, as well as being much lighter, more flexible,
and far less expensive. These TP products make cable runs
simpler and less cumbersome. Termination of the cable with
RJ-45 connectors is simple, quick, and economical.
It is possible to exceed the recommended distances,
however, image quality may be reduced.
About the TP Transmitter/DAs
System distribution
The transmitters split and buffer the transmitted signal four
(IN1124) or eight (IN1128) times. The receivers each have two
RGBHV and audio outputs. With this combination of a
transmitter/DA with a local monitor and four or eight buffered
receivers, the input signal can be widely distributed.
The Extron IN1124 inputs RGB video and computer audio,
converts the input to an output comprising the video and audio,
and distributes and transmits four identical proprietary signals
over TP cables to up to four IN1130 TP receivers. The IN1128
distributes and transmits eight proprietary signals on TP cables.
Both transmitter models provide a buffered local monitor video
output.
Transmission distance
The minimum reliable transmission distance between
transmitters and receivers is 50 feet. The maximum distance is
determined by the output frequency and resolution. The table
on the following page specifies the recommended maximum
transmission distances using Extron skew-free A/V UTP cable
or UTP CAT 5 cable, terminated with CAT 5 rated connectors.
1-2
www.camboard.de
IN1124/28/30
Transmission System • Introduction
Extron recommends using the highest quality cable
available and affordable, with less than 8 nanoseconds/
100 meters of skew (see Termination of TP cable in
chapter 2). We also recommend the use of preterminated and tested cables. Cables terminated on site
should be tested before use to ensure that they comply
with Category 5 specifications.
Both transmitter models sum the left and right channels of the
unbalanced stereo audio input and transmit mono audio on the
left and right channels. The transmitters have a local audio
output on a 3.5 mm female mini jack connector.
Tel. 07131 911201
Fax 07131 911203
[email protected]
IN1124/28/30 Transmission
System • Introduction
1-3
im Vertrieb
von
Introduction,
cont’d
CAMBOARD Electronics
IN1128 TP transmitter/distribution amplifier
About the TP Receiver
The Extron IN1130 TP receiver receives the transmission of one
of transmitter’s proprietary video and audio signal over a TP
cable. The receiver then decodes the received signal and buffers
and distributes two identical video outputs on female 15-pin
HD connectors. The receiver buffers and distributes two
identical mono audio outputs on 3.5 mm mini jacks.
The receiver has a sharpness control that fine tunes the
compensation to optimize the video outputs for various cable
lengths.
Computer video input — Accepts computer analog video on a
15-pin HD female connector. With an adapter cable, the
transmitter can accept Macintosh, 13W3 video, RGBHV,
RGBS, RGsB, component video, S-video, or single source
composite video input.
Buffered local monitor output — Allows you to view the
displayed image on a local monitor.
Audio input — Accepts stereo PC audio on a 3.5 mm stereo
mini jack. The transmitter sums the left and right audio
channels into two identical mono channels.
Features
IN1124 TP transmitter/distribution amplifier
Frequency range — Supports 15 kHz to 130 kHz horizontal
frequency.
RJ-45 connectors — Allows connection to up to eight Extron
IN1130 TP RGB video receivers.
Computer video input — Accepts computer analog video on a
15-pin HD female connector. With an adapter cable, the
transmitter can accept Macintosh, 13W3 video, RGBHV,
RGBS, RGsB, component video, S-video, or single source
composite video input.
Mounting — Can be rack mounted with Extron’s 1U rack shelf
(part #IN9080).
IN1130 TP receiver
The IN1130 TP receiver has the following features:
Buffered local monitor output — Allows you to view the
displayed image on a local monitor.
Video output — Provides two RGBHV, RGBS, or RGsB outputs
on 15-pin HD connectors. With an optional SY-VGA
cable, the receiver can output component video, S-video,
or composite video.
Audio input — Accepts stereo PC audio on a 3.5 mm stereo
mini jack. The transmitter sums the left and right audio
channels into two identical mono channels.
Audio output — Outputs mono audio on both the tip (left) and
the ring (right) of two 3.5 mm stereo mini jacks.
RJ-45 connectors — Allows connection to up to four Extron
IN1130 TP RGB video receivers.
RJ-45 connector — Allows attachment to an Extron IN1124 or
IN1128 TP transmitter/DA.
Mounting — Can be rack mounted with Extron’s 1U rack shelf
(part #IN9080).
1-4
Frequency range — Supports 15 kHz to 130 kHz horizontal
frequency.
www.camboard.de
IN1124/28/30
Transmission System • Introduction
Mounting — Can be mounted to virtually any flat surface with
Extron’s optional mounting brackets (part #IN9089).
Tel. 07131 911201
Fax 07131 911203
[email protected]
IN1124/28/30 Transmission
System • Introduction
1-5
im Vertrieb
von
Introduction,
cont’d
CAMBOARD Electronics
IN1124/IN1128/IN1130 Transmission System
2
Chapter Two
Installation and Operation
Installation Overview
Rack Mounting the Transmitter
Furniture Mounting the Receiver
Transmitter Cabling
Transmitted Signal Cabling
Receiver Cabling
Operation
Troubleshooting
1-6
www.camboard.de
IN1124/28/30
Transmission System • Introduction
Tel. 07131 911201
Fax 07131 911203
[email protected]
im Vertrieb
von
Installation
and Operation,
Operation
cont’d
CAUTION
CAMBOARD Electronics
Installation and service must be performed by
authorized personnel only.
Installation Overview
To install and set up a TP transmitter/DA and the associated TP
receiver(s) for operation, perform the following steps:
1
Disconnect power from all of the equipment, including the
video source(s) (such as computers or HDTV set-top
boxes), the transmitter, the receivers, and the output
display(s).
2
If desired, mount the transmitter in a rack. See Rack
Mounting the Transmitter in this chapter.
4
3
If desired, mount the receivers under furniture or to the
desired flat surfaces. See Furniture Mounting the Receiver in
this chapter.
4
Connect the input to the transmitter. See Transmitter
cabling in this chapter.
5
Connect the local monitor to the transmitter. See
Transmitter cabling in this chapter.
Figure 2-1 — Rack mounting the IN1124
6
Connect the cables between the transmitter and the TP
receivers. See Transmitted signal cabling in this chapter.
3.
Install an optional IN9088B blank panel or another unit to
the rack shelf.
7
Connect the output cables from the receivers to the
displays. See Output cabling in this chapter.
4.
Insert the shelf into the rack, aligning the holes in the shelf
with those in the rack.
5.
Secure the shelf to the rack.
8
Connect power supplies to the TP receivers and the TP
transmitter. Turn on the video source(s) and the output
display(s).
9
The receiver can be mounted under furniture or to any other flat
surface using optional mounting brackets for IN1130
(part #IN9089) (figure 2-2).
On each receiver, as necessary, adjust the sharpness
control. See Operation in this chapter.
The transmitter can be mounted in a 19" equipment rack using
an optional Rack-mount shelf (part #IN9080) (figure 2-1). The
transmitter mounts on the left or right side of the rack.
1.
If feet were previously installed on the bottom of the
transmitter, remove them.
2.
Mount the transmitter on the rack shelf, using the two
provided #6-32 x 1/4 screws to secure the receiver to the
shelf.
6-32 x 1/4" Screws
Use 2 mounting holes
Furniture Mounting the Receiver
Rack Mounting the Transmitter
2-2
False Front panel
Use 2 mounting holes
www.camboard.de
IN1124/28/30
Transmission System • Installation and OperationTel.
1.
Attach the mounting brackets to the receiver with the
machine screws provided.
2.
Hold the receiver with the attached brackets against the
surface where you want to mount the receiver. Mark the
location of the screw holes of the bracket on the mounting
surface.
3.
Drill pilot holes in the mounting surface at the marked
screw locations.
4.
Place the receiver against the surface and align the holes in
the brackets. Insert screws into the four pilot holes and
tighten all four screws to secure the receiver in place.
07131 911201IN1124/28/30 Transmission System
[email protected]
• Installation and Operation
Fax 07131 911203
2-3
im Vertrieb
von
Installation
and Operation,
cont’d
CAMBOARD Electronics
10
4
5
Figure 2-2 — Under-desk or through-desk mounting
1
5
5
5
2
3
4
2
1
4
3
9
Figure 2-3 — Installation features, IN1124
Transmitter Cabling
The IN1124 (figure 2-3) and the IN1128 (figure 2-4) accept and
transmit computer video and PC audio. These transmitters can
also accommodate component video, S-video, or composite
video if input on the R, G, and B pins of the 15-pin HD
connector using an Extron IN9045-L6 15HD male-to-5 BNC
male, 6’cable.
10
8
Video input connector — Connect computer video to this 15pin HD female connector.
1
5
1
15
11
5
The sense lines on the Input connector are
tied directly to the Local Output connector.
Input only sync signals, no video signals, on
the sync pins, 13 and 14.
5
5
6
7
8
1
2
3
4
5
5
5
2
1
4
3
9
Figure 2-4 — Installation features, IN1128
2
For composite video, use the G pin and the associated
return pin. For additional video signals, use the R, B,
and associated return pins.
5
5
For component video, use the R (R-Y) and R return pins
(pins 1 and 6), G (Y) and G return pins (pins 2 and 7),
and B (B-Y) and B return pins (pins 3 and 8).
For S-video, use the R, R return (C-chroma), G, and G
return (Y-luma) pins.
5
Audio input connector — Connect PC audio to this 3.5 mm,
stereo jack. Wire the male plug as shown in figure 2-5.
Input only analog, line level, audio signals on the audio
input connector.
Tip (L)
Sleeve (GND)
Ring (R)
Tip (L)
Sleeve (GND)
Figure 2-5 — Audio input wiring
2-4
www.camboard.de
IN1124/28/30
Transmission System • Installation and OperationTel.
07131 911201IN1124/28/30 Transmission System
[email protected]
• Installation and Operation
Fax 07131 911203
2-5
im Vertrieb
von
Installation
and Operation,
cont’d
Local Output connector — If desired, connect a local monitor
video cable to this 15-pin HD female connector.
3
4
CAMBOARD Electronics
5
1
15
11
standards. You can use either standard, but ensure you use the
same standard on both ends of the cable.
The sense lines on the Local Output
connector are tied directly to the Input
connector.
Side
Clip Down
12345678
Local audio output connector — If desired, connect the PC
audio output on this 3.5 mm, stereo jack to local powered
speakers.
Pin
Transmitted Signal Cabling
The IN1124 (figure 2-3) and IN1128 (figure 2-4) transmit
computer video and PC audio. The IN1130 (figure 2-6) receives
the transmission.
CAUTION
RJ-45 connector
12345678
Do not connect these devices to a computer data or
telecommunications network
TIA/EIA T 568 A
Wire color
TIA/EIA T 568 B
Wire color
Signal
1 White-green
White-orange
Red/V. sync+
2 Green
Orange
Red/V. sync-
3 White-orange
White-green
Green/H. sync+
4 Blue
Blue
Blue+
5 White-blue
White-blue
Blue-
6 Orange
Green
Green/H. sync-
7 White-brown
White-brown
Mono audio +
8 Brown
Brown
Mono audio -
Twisted Pairs
RJ-45 termination must comply with the
TIA/EIA T 568A or TIA/EIA T 568B wiring standards
for all connections.
1&2
7&8
3&6 4&5
10
Figure 2-7 — TP cable termination
Cable testing
7
8
7
8
11
6
To ensure proper cable termination, each transmission cable
system that uses CAT 5 cable should be tested (Extron’s skewfree UTP cable does not need to be tested). Testing the cable
from the RJ-45 connections at the transmitter and receiver gives
the most accurate indications of cable problems.
9
There are two varieties of cable runs: simple runs, in which a
single cable is terminated only at the transmitter and receiver,
and complex runs, which can include patch bays and multiple
terminations and lengths of cable. In either case, the entire
cabling system should be tested.
Figure 2-6 — Installation features, IN1130
5
RGB video transmission connector — Connect one end of a TP
cable to each of these RJ-45 female connectors.
6
RGB video reception connector — Connect the free end of one
of the TP cables connected to the transmitter to this RJ-45
connector.
Termination of TP cable
Figure 2-7 details the recommended termination of TP cables in
accordance with the TIA/EIA T 568A or TIA/EIA T 568B wiring
2-6
www.camboard.de
IN1124/28/30
Transmission System • Installation and OperationTel.
A complete test measures cable length and tests the wire map,
attenuation, NEXT, PSNEXT, ELFEXT, PSELFEXT, return loss,
ACR and PSACR. All of these tests are critical for digital data
transfer, but not for analog video. While all of these tests are
important indicators of the quality of the cable termination, the
most critical testing parameters for video transfer are wire map
(T-568-A or T-568-B termination) and pair length measurements.
The largest concern is equalization of skew between cable pairs.
Cable systems of 300 feet or less should exhibit no transmission
problems if they pass at least CAT 5 channel certification testing.
07131 911201IN1124/28/30 Transmission System
[email protected]
• Installation and Operation
Fax 07131 911203
2-7
im Vertrieb
von
Installation
and Operation,
cont’d
CAMBOARD Electronics
The Microtest OMNI SCANNER 2 performs comprehensive
certification testing to the proposed CAT 6 standards. Other
manufacturers also make testing equipment. The tests include
advanced diagnostics for troubleshooting the cause and location
of many cable and termination problems. For simple
installation testing, the Microtest MICRO SCANNER PRO tests
wire map and cable length, including individual cable pair
length.
Extron skew compensation coax cables are available in lengths
of 2 through 20 feet, see Appendix A for part numbers.
Extron IN1128
TP Transmitter/DA
Equalizing pair skew
8
7
6
5
The manufacturing process for network (CAT 5) UTP cable
leads to a condition called pair skew. For best results, pair skew
needs to be equalized when using the CAT 5 cable in A/V
applications. The design of Extron’s skew-free A/V UTP cable
minimizes pair skew to the point that equalization is not
required.
Computer
CAT 5 UTP Cable
IF cable measurement
indicates that the pair
with wires 1 and 2 is
four feet shorter than
the other signals...
Skew exists between pairs when the physical length of one wire
pair is different from another. As the transmission cable length
increases, the amount of skew increases. Skew affects the
displayed image when the differential length between wire
pairs exceeds 2 feet, causing the timing of the red, green, and
blue video signals to appear out of alignment (horizontal
registration errors). A white vertical line on a black field can
appear as individual red, green, and blue lines that are close
together; the signal transmitted on the shortest wire pair leads
the other colors and appears to the left on the display.
•
TP Receivers
RGB video
1, 2
Red
3, 6
Green
4, 5
Blue
Projector
Receiver Cabling
by using an Extron IN9045-L6 15HD male-to-5 BNC male,
6’cable, to adapt the output on a 15-pin HD connector to
BNC connectors,
The IN1130 (figure 2-6) outputs two identical sets of RGB video
and mono audio. This receiver can also receive component
video, S-video, or composite video and output them on the R,
G, and B signal lines.
7
and then adding an additional length of coax equal to the
length of pair skew, placed on the receiver’s output,
you can equalize the effects of pair skew (figure 2-8).
If UTP cable test measurement cannot be done, pair skew can
still be equalized by viewing a test pattern with a critical eye.
Examine the test pattern for loss of horizontal registration and,
through a process of trial and error, equalize any pair skew with
coax extensions on the red, green, and/or blue outputs.
2-8
Pair
Figure 2-8 — Pair skew equalization
UTP cable test equipment measures and reports wire pair
length. The report on the various pair lengths can be used in
equalizing pair skew. The nominal velocity of propagation
(NVP — the speed at which the signal travels on the
transmission line, measured as a percentage of the speed of
light) of TP cable is very close to that of conventional coaxial
cable. The similarity in NVP means that:
•
Extron IN1130
... THEN insert a 15HD-to-BNC
extension cable and a four-foot
skew compensation cable to
equalize UTP skew for red video.
www.camboard.de
IN1124/28/30
Transmission System • Installation and OperationTel.
8
Output 1 and 2 — Connect the desired video output devices to
the rear panel output 15-pin HD connectors.
5
1
15
11
Outputing component video, S-video, or composite
video on the 15-pin HD connectors requires an
Extron IN9045-L6 15HD male-to-5 BNC male,
6’cable.
Audio output 1 and 2 — Connect the mono PC audio output on
these 3.5 mm jacks to local powered speakers.
07131 911201IN1124/28/30 Transmission System
[email protected]
• Installation and Operation
Fax 07131 911203
2-9
im Vertrieb
von
Installation
and Operation,
cont’d
CAMBOARD Electronics
Operation
9
IN1124/IN1128/IN1130 Transmission System
Power — Plug the external 9V power supply into this power
connector. The power supply is included with the unit. Plug
the power supply into a 100 to 240VAC, 50 Hz or 60 Hz power
source.
Alternatively, an Extron P/S 100 Universal 12VDC Power
Supply can power up to six transmitters or receivers using only
one AC power connector.
10
Power LED — Lights to indicate that power is applied.
11
Sharpness control — Adjusts the sharpness of both images
simultaneously. Use a Tweeker or other small, flat-head,
screwdriver to adjust the control.
Troubleshooting
1.
Ensure that all devices are receiving power. The
transmitter’s and receiver’s front panel Power LEDs
indicate that they are receiving power.
2.
Ensure that the transmitter is receiving a video input.
3.
Ensure that the TP cable(s) are properly terminated in
accordance with TIA/EIA T 568A or TIA/EIA T 568B
standards and that the RJ-45 connections are securely
made.
4.
The transmission distance may be too short. Ensure that
the UTP cable is at least 50 feet long.
5.
The transmission distance may be too long. Try
shortening the distance between the transmitter and
receivers.
6.
Call the Extron S3 Sales & Technical Support Hotline if
necessary.
A
Appendix A
Reference Information
Specifications
Included Parts
Accessories
Installation Kits
Cables/Adapters
2-10
www.camboard.de
IN1124/28/30
Transmission System • Installation and OperationTel.
07131 911201
Fax 07131 911203
[email protected]
imInformation
Vertrieb von
Reference
Reference
Information
cont’d
CAMBOARD Electronics
Video
Input impedance ..........................
Output impedance ......................
Max. propagation delay ..............
Max. rise/fall time .......................
Number/signal type ................... 1, 4 or 8 sets of proprietary analog signals
Connectors .................................... 1, 4 or 8 RJ-45 female
510 ohms
75 ohms
48 ns
3.5 ns
Video input
Number/signal type
IN1124, IN1128 .................. 1 analog VGA-UXGA RGBHV, RGBS, RGsB
and
1 unbuffered local monitor output of
analog VGA-UXGA RGBHV, RGBS, RGsB
IN1130 ............................... 1 set of proprietary analog signals
Connectors
IN1124, IN128 .................... 1 female 15-pin HD for input
1 female 15-pin HD for unbuffered local
monitor loop-through (Mac and Sun/SGI
to VGA adapters are available)
IN1130 ............................... 1 shielded female RJ-45
Nominal level ............................... 0.7V p-p for RGB
Minimum/maximum levels ...... Analog: 0.3V to 1.5V p-p with no offset at
unity gain
Impedance .................................... 75 ohms
Horizontal frequency .................. 15 kHz to 130 kHz
Vertical frequency ....................... 30 Hz to 150 Hz
Audio — audio models only
Number/signal type ...................
Connectors ....................................
Frequency response .....................
THD + Noise ................................
S/N ...............................................
Crosstalk .......................................
Stereo channel separation ..........
CMRR ............................................
Audio input
Number/signal type
IN1124, IN1128 ................. 1 stereo, unbalanced, and 1 local output
IN1130 ............................... 1 set of proprietary analog signals
Connectors
IN1124, IN1128 ................. (1) 3.5 mm mini stereo jack
(1) 3.5 mm mini stereo jack (for
unbuffered local output)
IN1130 ............................... 1 shielded RJ-45 female
Impedance .................................... >5 kohms unbalanced, DC coupled
Nominal level ............................... -10dBV (316mV)
Maximum level ............................ +5.5dBu, (unbalanced) at 1%THD+N
Video output
Number/signal type
IN1124 ...............................
IN1128 ...............................
IN1130 ...............................
Connectors
IN1124 ...............................
IN1128 ...............................
IN1130 ...............................
Nominal level ...............................
Minimum/maximum levels ......
Impedance ....................................
4 sets of proprietary analog signals
8 sets of proprietary analog signals
2 analog RGBHV, RGBS, RGsB
Audio output
Number/signal type
IN1124 ...............................
IN 1128 ..............................
IN1130 ...............................
Connectors
IN1124 ...............................
IN1128 ...............................
IN1130 ...............................
Impedance ....................................
Nominal level ...............................
4 shielded female RJ-45
8 shielded female RJ-45
2 female 15-pin HD
0.7V p-p for RGB
0.3V to 1.5V p-p
75 ohms
Sync
Input type .....................................
Output type ..................................
Input level .....................................
Output level ..................................
A-2
RGBHV, RGBS, RGsB
RGBHV, RGBS, RGsB
2.0V to 5.5V p-p
4.0V to 5.0V p-p
TTL: 5.0V p-p, unterminated
www.camboard.de
IN1124/28/30
Transmission System • Reference Information
4 or 8 sets of analog proprietary signals
4 or 8 RJ-45 female
20 Hz to 20 kHz, ±0.05dB
0.3% @ 1 kHz at nominal level
>68dB at rated maximum output
<-80dB @ 1 kHz
>80dB @ 1 kHz
>33dB @ 20 Hz to 20 kHz
4 sets of proprietary analog signals
8 sets of proprietary analog signals
2 mono, unbalanced
4 shielded RJ-45 female
8 shielded RJ-45 female
(2) 3.5 mm mini jacks
5 kohms unbalanced, 10 kohms balanced
-10dBV (316mV)
0dBu = 0.775 volts (RMS).
Tel. 07131 911201
Fax 07131 911203
[email protected]
IN1124/28/30 Transmission
System • Reference Information
A-3
imInformation
Vertrieb von
Reference
cont’d
CAMBOARD Electronics
General
Included Parts
Power ............................................. 100VAC to 240VAC, 50/60 Hz, 15 watts,
external, autoswitchable
IN1124, IN1128 ................. External 9VDC, 2.0A power supply.
Product requires 1.6 A.
IN1130 ............................... External 9VDC, 0.5A power supply.
Product requires 0.45 A.
Temperature/humidity .............. Storage -40° to +158°F (-40° to +70°C) /
10% to 90%, non-condensing
Operating +32° to +122°F (0° to +50°C) /
10% to 90%, non-condensing
Rack mount
IN1124, IN1128 ................. Yes, with optional 1U rack shelf, part
#IN9080
IN1130 ............................... No, but furniture or other flat surface
mountable with optional #IN9089
mounting brackets
Enclosure type .............................. Metal
Enclosure dimensions
IN1124, IN1128 ................. 1.7” H x 8.5” W x 6.0” D (1U high, half
rack width)
4.2 cm H x 21.6 cm W x 14.7 cm D
(Depth excludes connectors.)
IN1130 ............................... 1.7” H x 5.6” W x 3.75” D (1U high)
(4.3 cm H x 14.2 cm W x 9.5 cm D)
(Depth excludes connectors.)
Product weight
IN1124 ............................... 1.0 lb (0.5 kg)
IN1128 ............................... 1.5 lb (0.7 kg)
IN1130 ............................... 0.7 lb (0.3 kg)
Shipping weight
IN1124 ............................... 3 lbs (1.4 kg)
IN1128 ............................... 4 lbs (1.8 kg)
IN1130 ............................... 2 lbs (0.9 kg)
Vibration ....................................... ISTA/NSTA 1A in carton (International
Safe Transit Association)
Listings .......................................... ETL (UL1950)
Compliances ................................. CE
MTBF ............................................. 30,000 hours
Warranty ....................................... 3 years parts and labor
These items are included in each order for a specific TP
transmitter or receiver:
Included parts
Replacement part number
IN1124
Twisted pair transmitter/DA for high-resolution
video and audio
IN1124-2
IN1124/28/30 Transmission System User’s Guide
9.0VDC, 120VAC 60Hz, 2.0A external power supply
IN9211-1
-or- 9.0VDC, 230VAC 50 Hz, 2.0A external power supply
IN9211-5
Adjustment tool with technician’s blade
IN9339
IN1128
Twisted pair transmitter/DA for high-resolution
video and audio
IN1128-2
IN1124/28/30 Transmission System User’s Guide
9.0VDC, 120VAC 60Hz, 2.0A external power supply
IN9211-1
-or- 9.0VDC, 230VAC 50 Hz, 2.0A external power supply
IN9211-5
Adjustment tool with technician’s blade
IN9339
IN1130
Twisted pair receiver/DA for high-resolution
video and audio
IN1130-2
IN1124/28/30 Transmission System User’s Guide
9.0VDC, 120VAC 60Hz, 0.5A external power supply
IN9204-1
-or- 9.0VDC, 230VAC 50 Hz, 0.5A external power supply
IN9204-2
Adjustment tool with technician’s blade
IN9339
Specifications are subject to change without notice.
A-4
www.camboard.de
IN1124/28/30
Transmission System • Reference Information
Tel. 07131 911201
Fax 07131 911203
[email protected]
IN1124/28/30 Transmission
System • Reference Information
A-5
imInformation
Vertrieb von
Reference
cont’d
CAMBOARD Electronics
Skew-free A/V cable
Suggested Accessories
Accessory
Part number
P/S 100 Multiple output 12V power supply
60-357-01
1U rack-mount shelf (for IN1124, IN1128)
IN9080
Rack-mount shelf blank panel (for IN1124, IN1128)
IN9088B
Mounting brackets (for IN1130)
IN9089
Cables/Adapters
Skew-Free A/V UTP cables are not recommended for
Ethernet/LAN applications.
3’ Skew-free A/V UTP
26-569-01
6’ Skew-free A/V UTP
26-569-02
12’ Skew-free A/V UTP
26-569-03
25’ Skew-free A/V UTP
26-569-04
35’ Skew-free A/V UTP
26-569-05
Part number
50’ Skew-free A/V UTP
26-569-06
15HD male-to-male, 6’
IN8006M
75’ Skew-free A/V UTP
26-569-07
15HD male-to-male, 12’
IN8012M
100’ Skew-free A/V UTP
26-569-08
15HD male-to-male, 25’
IN8025M
150’ Skew-free A/V UTP
26-569-09
IN80xxM
200’ Skew-free A/V UTP
26-569-10
15HD male-to-female, 6’
IN8006
250’ Skew-free A/V UTP
26-569-11
15HD male-to-female, 12’
IN8012
300’ Skew-free A/V UTP
26-569-12
15HD male-to-female, 25’
IN8025
25’ Skew-free Plenum
26-570-04
15HD male-to-female, 35-240’’
IN80xx
35’ Skew-free Plenum
26-570-05
50’ Skew-free Plenum
26-570-06
75’ Skew-free Plenum
26-570-07
100’ Skew-free Plenum
26-570-08
15HD-terminated cable
15HD male-to-male, 35-240’’
15HD-5BNC adapter cable
A-6
Part number
Part number
15HD male-to-5 BNC male, 6’
IN9045-L6
15HD male-to-5 BNC male, 12’
IN9045-L12
15HD male-to-5 BNC male, 25’
IN9045-L25
15HD male-to-5 BNC male, 35’
IN9045-L50
150’ Skew-free Plenum
26-570-09
15HD male-to-5 BNC male, 50’
IN9045-L50
200’ Skew-free Plenum
26-570-10
250’ Skew-free Plenum
26-570-11
300’ Skew-free Plenum
26-570-12
Plenum 15HD-5BNC adapter cable
Part number
15HD male-to-5 BNC male, plenum, 25’
IN9045FP-L25
15HD male-to-5 BNC male, plenum, 35’
IN9045FP-L50
15HD male-to-5 BNC male, plenum, 50’
IN9045-L50
15HD male-to-5 BNC male, plenum, 75’
IN9045LP-L75
www.camboard.de
IN1124/28/30
Transmission System • Reference Information
Tel. 07131 911201
Fax 07131 911203
Skew-free A/V cable
Bulk cable
Part number
Part number
Skew-free A/V UTP 1000’ (Bulk) (non-plenum)
22-141-03
Skew-free A/V UTP 1000’ (Bulk) (plenum)
22-142-03
[email protected]
IN1124/28/30 Transmission
System • Reference Information
A-7
imInformation
Vertrieb von
Reference
cont’d
RJ-45 connector
Part number
CAT 6 jack (black)
10-463-10
CAT 6 jack (red)
10-463-11
CAT 6 jack (blue)
10-463-12
CAT 6 jack (orange)
10-463-13
CAT 6 jack (grey)
10-463-14
CAT 6 jack (white)
10-463-15
CAT 6 jack (ivory)
10-463-16
Skew compensation cable
Part number
2’ skew cable (red, green, blue)
26-524, 525, 526-01
4’ skew cable (red, green, blue)
26-524, 525, 526-02
6’ skew cable (red, green, blue)
26-524, 525, 526-03
8’ skew cable (red, green, blue)
26-524, 525, 526-04
10’ skew cable (red, green, blue)
26-524, 525, 526-05
12’ skew cable (red, green, blue)
26-524, 525, 526-06
14’ skew cable (red, green, blue)
26-524, 525, 526-07
16’ skew cable (red, green, blue)
26-524, 525, 526-08
18’ skew cable (red, green, blue)
26-524, 525, 526-09
20’ skew cable (red, green, blue)
26-524, 525, 526-10
Assorted cables and adapters
A-8
CAMBOARD Electronics
Part number
SVHS 6’ (6 feet/1.8 meters)
26-316-02
SVHSM - BNCF
26-353-01
SVHSM - BNCM-3’
26-353-03
www.camboard.de
IN1124/28/30
Transmission System • Reference Information
Tel. 07131 911201
Fax 07131 911203
[email protected]