Download Datalogic DS6300 User`s guide

DS6300
INSTALLATION QUICK REFERENCE
CONTENTS
DS6300-100-010 MASTER/SLAVES MODELS.......................................................................................................1
DS6300-100-012 ETHERNET MODELS..................................................................................................................5
DS6300-105-0XX OSCILLATING MIRROR MODELS ............................................................................................9
COMMON FEATURES ..........................................................................................................................................11
For further details on product installation, see the complete Reference Manual available on the
configuration CD-ROM included with this product.
NOTE
DS6300-100-010
Master/Slave Models
1
Figure A
1 Laser Beam Output Window
1
5
1
3
4
3
2
2
Figure B
Figure C
1 Programming Keypad
4 Power On LED (Red)
2 TX Data LED (Green)
5 LCD Display
1 Main/Aux. Interface 25-pin Connector
2 Lonworks 9-pin Male Connector
3 Lonworks 9-pin Female Connector
3 Phase On LED (Yellow)
Available Models:
DS6300 - 10X - 0YY
Decoder Model
Optical Model
10 = Master/Slave
11 = Profibus
12 = Ethernet
15 = Devicenet
0 = Standard
5 = Oscillating Mirror
The following tables display each version’s reading performance.
ELECTRICAL FEATURES
Supply Voltage 12 - 30 Vdc
Power
15 W typical
Consumption
20 W Max. (including startup current)
Communication Main (isolated)
Aux
Other
Interfaces
RS232
RS485 fullduplex
RS232 Lonworks
RS485 halfduplex
Baud Rates
Inputs
Ext. Trigger 1,
3 aux. digital
inputs
Outputs
3 software
programmable
digital outputs
2400 to 115200
115200
(optocoupled NPN or PNP)
(optocoupled)
OPTICAL FEATURES
Light Receiver
Avalanche photodiode
Wavelength
630 to 680 nm
Safety Class
Class 2-EN 60825-1; Class IICDRH
Laser Control
Security system to turn laser
off in case of motor slow down
READING FEATURES
Scan Rate
600-1200 scans/s
Max. Resolution
0.2 mm (8 mils)
Max. Read. Distance
Max. Read. Width
(see reading diagram)
Max. Depth of Field
Aperture Angle
USER INTERFACE
LCD Display
Keypad
LED Indicators
2 lines by 16 characters LCD
3 keys
Power ON (red color)
Phase ON (yellow color)
TX Data (green color)
1
DS6300 QUICK REFERENCE
SOFTWARE FEATURES
Readable Codes
Interleaved 2/5
2/5 compressed
Code 39 standard
Codabar
Code 128
EAN 128
Code 93 (standard & full ASCII)
EAN/UPC
Code Selection
Up to 10 codes during one
reading phase
Headers and
Up to 128-byte headers and
Terminators
128-byte terminators
Operating Modes
On Line, Automatic, Test,
Config. Mode
Genius™ utility program
Parameter Storage Non-volatile internal FLASH
ENVIRONMENTAL FEATURES
Operating
0° to +40 °C (+32 to +104 °F)
Temperature
Storage
-20° to +70 °C (-4° to +158 °F)
Temperature
Humidity
90% non condensing
Vibration
IEC 68-2-6 test FC
Resistance
1.5 mm; 10 to 55 Hz
2 hours on each axis
Shock Resistance IEC 68-2-27 test EA
30 G; 11 ms
3 shocks on each axis
Protection Class
IP64
PHISYCAL FEATURES
Std Models
Dimensions
(inch)
Weight
Oscill. Mirror
mm 110x113x99
113x180x104.5
(4.33x4.45x3.9) (4.45x7.08x4.11)
1.5 kg (3.3 lb)
2.0 kg (4.4 lb)
Accessories:
Name
GFC-60
GFC-600
CAB-6001
CAB-6002
CAB-6005
CAB-6101
CAB-6102
CAB-6105
CAB-6112
CAB-6115
CAB-6205
CAB-6210
INT-60
PWR-120
BTK-6000
PG6002
PG6001
PG6000
FBK-6000
USX-60
Description
90° mirror
90° mirror close distance
Cable to C-BOX100 1 m
Cable to C-BOX100 2 m
Cable to C-BOX100 5 m
Cable master/slave 1 m
Cable master/slave 2 m
Cable master/slave 5 m
Cable master/slave no power 2 m
Cable master/slave no power 5 m
Cable to SC8000 5 m
Cable to SC8000 10 m
20 mA C.L. interface board
Power unit 110/230 V AC - 24 V DC
Terminator kit (5 pcs)
Single unit power supply – US
Single unit power supply – UK
Single unit power supply – EU
Fast bracket kit (2 pcs)
Adjustable bracket
Part Number
93A201100
93A201102
93A051190
93A051200
93A051210
93A051220
93A051230
93A051240
93A051224
93A051225
93A051250
93A051260
93A151021
93ACC1530
93ACC1710
93ACC1718
93ACC1719
93ACC1720
93ACC1721
93ACC1729
Electrical Connections:
The DS6300 reader provides a 25-pin male D-sub connector for connection to power supply, Host interface (Main
and Aux), and input/output signals.
Two 9-pin connectors provide access to the scanner’s local Lonworks network used for both input and output
connections to build a multi-sided or omni-station system.
2
DS6300 QUICK REFERENCE
The details of the connector pins are indicated in the following table:
25-pin D-Sub Male Connector Pinout
Pin
1
20
21
8
22
11
12
16
17
18
19
6
10
14
15
24
9, 13
23, 25
Name
Function
Shield
RXAUX
TXAUX
OUT 1+
OUT 1OUT 2+
OUT 2OUT 3A
OUT 3B
EXT_TRIG A
EXT_TRIG B
IN2A
IN2B
IN3A
IN4A
IN_REF
VS
GND
Internally connected by capacitor to chassis
Receive data of auxiliary RS232 (referred to GND)
Transmit data of auxiliary RS232 (referred to GND)
Configurable digital output 1 – positive pin
Configurable digital output 1 – negative pin
Configurable digital output 2 – positive pin
Configurable digital output 2 – negative pin
Configurable digital output 3 – polarity insensitive
Configurable digital output 3 – polarity insensitive
External trigger (polarity insensitive)
External trigger (polarity insensitive)
Input signal 2 (polarity insensitive)
Input signal 2 (polarity insensitive)
Input signal 3 (polarity insensitive)
Input signal 4 (polarity insensitive)
Common reference of IN3 and IN4 (polarity insensitive)
Supply voltage – positive pin
Supply voltage – negative pin
1
13
14
25
25-pin male D-sub Connector
Pin
RS232
RS485 Full-Duplex
RS485 Half-Duplex
2
3
4
5
7
TX
RX
RTS
CTS
GND_ISO
TX485+
RX485+
TX485RX485GND_ISO
RTX485+
RTX485GND_ISO
9-pin Lonworks Connector Pinout
Pin
1
9
2
6
3
4
5
7
8
Name
Function
Shield
VS
GND
VS_I/O
Ref_I/O
SYS_ENC_I/O
SYS_I/O
LON A
LON B
Cable shield
Supply voltage – positive pin
Supply voltage – negative pin
Supply voltage of I/O circuit
Reference voltage of I/O circuit
System signal
System signal
Lonworks line (polarity insensitive)
Lonworks line (polarity insensitive)
1
5
9
6
Female
5
1
6
9
Male
Local Lonworks Connectors
Network Termination:
When building a local Lonworks system the network must be properly terminated by positioning a BTK-6000
terminator on the DS6300 master reader (BTK-6000 female side) and on the last slave reader (BTK-6000 male
side).
9-pin female
9-pin male
BTK-6000 Network Terminator
3
DS6300 QUICK REFERENCE
Connectivity:
Point-to-point layout
Local Lonworks Network (Single P.S.)
Master
DS6300
* C-BOX 100
CAB600X
CAB610X
* C-BOX 100
BTK6000
CAB600X
Local Host
Slave 1
Local Host
P.S.
BTK6000
CAB610X
PG6000
PWR120
Slave 2
Single P.S. with 3 Readers
Local Lonworks Network (Single P.S.)
Master
CAB600X
* C-BOX 100
CAB611X
Slave 1
CAB610X
PWR120
Slave 2
Local Host
CAB610X
Slave 3
Single P.S. with more than 3 Readers
Local Lonworks Network (Multi P.S.)
CAB611X
Slave 3
CAB610X
CAB610X
Slave 2
Slave 1
CAB600X
Master
* C-BOX 100
* C-BOX 100
PWR120
Local Host
*
4
C-BOX 100 can support up to 2 DS6300 readers. Please contact Datalogic USS Technical Support, if your
application requires a multi-slave network.
DS6300-100-012
Ethernet Models
1
Figure A
1 Laser Beam Output Window
3
5
1
3
4
1
2
2
Figure B
Figure C
1 Programming Keypad
4 Power On LED (Red)
2 TX Data LED (Green)
5 LCD Display
1 RJ45 Modular Connector for Ethernet Interface
2 Lonworks 9-pin Female Connector
3 Main/Aux. Interface 26 D-Sub Male Connector
3 Phase On LED (Yellow)
Available Models:
DS6300 - 10X - 0YY
Decoder Model
Optical Model
10 = Master/Slave
11 = Profibus
12 = Ethernet
15 = Devicenet
0 = Standard
5 = Oscillating Mirror
The following tables display each version’s reading performance.
ELECTRICAL FEATURES
Supply Voltage 12 - 30 Vdc
Power
15 W typical
Consumption
20 W Max. (including startup current)
Communication Main (isolated)
Aux
Other
Interfaces
RS232 Lonworks
RS232
Ethernet
RS485 fullduplex
RS485 halfduplex
Baud Rates
Inputs
Ext. Trigger 1,
3 aux. digital
inputs
Outputs
3 software
programmable
digital outputs
2400 to 115200
115200
(optocoupled NPN or PNP)
(optocoupled)
OPTICAL FEATURES
Light Receiver
Avalanche photodiode
Wavelength
630 to 680 nm
Safety Class
Class 2-EN 60825-1; Class IICDRH
Laser Control
Security system to turn laser
off in case of motor slow down
READING FEATURES
Scan Rate
600-1200 scans/s
Max. Resolution
0.2 mm (8 mils)
Max. Read. Distance
Max. Read. Width
(see reading diagram)
Max. Depth of Field
Aperture Angle
USER INTERFACE
LCD Display
Keypad
LED Indicators
2 lines by 16 characters LCD
3 keys
Power ON (red color)
Phase ON (yellow color)
TX Data (green color)
5
DS6300 QUICK REFERENCE
SOFTWARE FEATURES
Readable Codes
Interleaved 2/5
2/5 compressed
Code 39 standard
Codabar
Code 128
EAN 128
Code 93 (standard & full ASCII)
EAN/UPC
Code Selection
Up to 10 codes during one
reading phase
Headers and
Up to 128-byte headers and
Terminators
128-byte terminators
Operating Modes
Config. Mode
On Line, Automatic, Test,
Genius™ utility program
Parameter Storage
Non-volatile internal FLASH
ENVIRONMENTAL FEATURES
Operating
0° to +40 °C (+32 to +104 °F)
Temperature
Storage
-20° to +70 °C (-4° to +158 °F)
Temperature
Humidity
90% non condensing
Vibration
IEC 68-2-6 test FC
1.5 mm; 10 to 55 Hz
Resistance
2 hours on each axis
Shock Resistance IEC 68-2-27 test EA
30 G; 11 ms
3 shocks on each axis
PHISYCAL FEATURES
Std Models
Dimensions
(inch)
Weight
Oscill. Mirror
mm 110x113x99
113x180x104.5
(4.33x4.45x3.9) (4.45x7.08x4.11)
1.5 kg (3.3 lb)
2.0 kg (4.4 lb)
Accessories:
Name
GFC-60
GFC-600
CAB-6011
CAB-6012
CAB-6015
CAB-6205
CAB-6210
INT-60
PWR-120
BTK-6000
PG6002
PG6001
PG6000
FBK-6000
USX-60
Description
90° mirror
90° mirror close distance
Cable to C-BOX100 1 m
Cable to C-BOX100 2 m
Cable to C-BOX100 5 m
Cable to SC8000 5 m
Cable to SC8000 10 m
20 mA C.L. interface board
Power unit 110/230 V AC - 24 V DC
Terminator kit (5 pcs)
Single unit power supply – US
Single unit power supply – UK
Single unit power supply – EU
Fast bracket kit (2 pcs)
Adjustable bracket
Part Number
93A201100
93A201102
93A051221
93A051222
93A051223
93A051250
93A051260
93A151021
93ACC1530
93ACC1710
93ACC1718
93ACC1719
93ACC1720
93ACC1721
93ACC1729
Electrical Connections:
The DS6300 Ethernet reader provides a 26-pin male D-sub connector for connection to power supply and
input/output signals.
An Ethernet connector is used for connection to the remote Host (for ex. Remote PC connected via Internet),
while a local Lonworks 9-pin male connector connects the Ethernet master to the first slave reader of the system.
The details of the connector pins are indicated in the following table:
6
DS6300 QUICK REFERENCE
26-pin D-Sub Male Connector Pinout
Pin
Name
1
20
21
8
22
11
12
16
17
18
19
6
10
14
15
24
9, 13
23, 25, 26
Shield
RXAUX
TXAUX
OUT 1+
OUT 1OUT 2+
OUT 2OUT 3A
OUT 3B
EXT_TRIG A
EXT_TRIG B
IN2A
IN2B
IN3A
IN4A
IN_REF
VS
GND
Function
Internally connected by capacitor to chassis
Receive data of auxiliary RS232 (referred to GND)
Transmit data of auxiliary RS232 (referred to GND)
Configurable digital output 1 – positive pin
Configurable digital output 1 – negative pin
Configurable digital output 2 – positive pin
Configurable digital output 2 – negative pin
Configurable digital output 3 – polarity insensitive
Configurable digital output 3 – polarity insensitive
External trigger (polarity insensitive)
External trigger (polarity insensitive)
Input signal 2 (polarity insensitive)
Input signal 2 (polarity insensitive)
Input signal 3 (polarity insensitive)
Input signal 4 (polarity insensitive)
Common reference of IN3 and IN4 (polarity insensitive)
Supply voltage – positive pin
Supply voltage – negative pin
9
1
10
19
18
26
26-pin male D-sub Connector
Pin
RS232
RS485 Full-Duplex
RS485 Half-Duplex
2
3
4
5
7
TX
RX
RTS
CTS
GND_ISO
TX485+
RX485+
TX485RX485GND_ISO
RTX485+
RTX485GND_ISO
9-pin Lonworks Connector Pinout
Pin
1
9
2
6
3
4
5
7
8
Name
Shield
VS
GND
VS_I/O
Ref_I/O
SYS_ENC_I/O
SYS_I/O
LON A
LON B
Function
Cable shield
Supply voltage – positive pin
Supply voltage – negative pin
Supply voltage of I/O circuit
Reference voltage of I/O circuit
System signal
System signal
Lonworks line (polarity insensitive)
Lonworks line (polarity insensitive)
5
1
6
9
Male Local Lonworks Connectors
RJ45 Female Modular Connector
HUB / SWITCH
DS6300
TX+
1
1
TX-
2
2
RX+
3
3
n. c.
4
4
n. c.
5
5
RX-
6
6
n. c.
7
7
n. c.
8
8
1
8
RJ45 Female Modular Connector
n. c. = not connected
7
DS6300 QUICK REFERENCE
Connectivity:
Point-to-point layout
Remote Host
DS6300
* C-BOX 100
CAB601X
PG6000
Ethernet Network
Remote Host
Ethernet
Master
CAB601X
* C-BOX 100
Slave 1
PWR120
Slave 2
*
8
C-BOX 100 can support up to 2 DS6300 readers. Please contact Datalogic USS Technical Support, if your
application requires a multi-slave network.
DS6300-105-0XX
Oscillating Mirror Models
1
Figure A
1 Laser Beam Output Window
Oscillating mirror models are used when coverage of a large reading area is required, mainly in picket fence
applications.
The DS6300 scanner mounts a dedicated optic head with integrated oscillating mirror driven by a linear motor.
The speed, precision, repeatability, and reliability of this driving technology assure high level performance.
The new oscillating mirror is completely software controlled and software programmable. The Genius™ software
tool allows adjusting the linear motor speed (oscillating frequency) and the upper and lower limits of the oscillation
by defining the top and bottom line limit angles.
When the oscillating mirror is programmed to read barcode labels at very small angles, position the reader to
assure at least 10° for the Skew angle (see DS6300 Reference Manual). This angle refers to the most inclined or
external laser line, so that all other laser lines assure more than 10° Skew. This avoids the direct reflection of the
laser light emitted by the reader.
10°
Oscillating Mirror Skew Angle
Otherwise, the scanner can be mounted at an angle of inclination of 17.5° in order to attain symmetrical deflection
ranges.
10
7.
5°
17.5°
Oscillating Mirror Reading Position
In the above case, the zone where the scan line is perpendicular to the reflecting surface corresponds to a neutral
zone at the center of the reading field.
9
DS6300 QUICK REFERENCE
The mirror can be deflected up to 40°. Oscillation with respect to the output window median axis is asymmetrical
(see figure below).
°
3 7 .5
40°
-2.5°
0°
Oscillating Mirror Maximum Aperture and Asymmetry
By configuring the oscillating speed up to the maximum value of 19 Hz, raster emulation can be performed for
reading fast moving objects.
Hz
Max. Aperture
0-5
6-10
11-15
6-19
40°
30°
20°
10°
By limiting the raster width to the minimum necessary, the number of scans on the reading
surface is increased.
NOTE
Oscillating angles are selected in software where the
minimum and maximum angles correspond to –2.5° and
+37.5°.
+37.5°
+17.5°
The scanner can be tilted in order for the 17.5° software
setting to correspond with the 0° horizontal plane.
-2.5°
Oscillating Mirror Extreme Angle Positions
These models provide higher scanning speed (1200 scans/sec) compared to standard models and the reading
performance is not adversely effected by the oscillating mirror.
The example represents the selection of an angle of
+10° for the bottom line and an angle of +20° for the top
line (see figure below).
+37.5°
+27.5°
+17.5°
Oscillating Mode
10
Common Features
Mechanical Installation:
TM
The DS6300 reader can be positioned and installed in the best way possible as a result of the Step-A-Head
feature. Thanks to the separation between Head and Base, you can modify the orientation of the decoder base,
and therefore display-keypad and connector panels, while keeping the optic head in the correct reading position.
The reading head and the decoder base can be rotated independently from each other allowing the installation
even in the most critical locations.
Step-A-Head™ Feature
The following diagrams give the overall dimensions of the reader standard model, oscillating mirror model and
mounting bracket. They may be used for their installation:
16.5
0.65
85
3.34
42
1.65
22
0.86
4
0.15
30
1.18
76
2.99
50
1.96
35
1.37
5.11
130
30
1.18
82
3.22
50
1.96
20
0.78
60
2.36
25
0.98
18
0.71
10
0.4
Ø4.1
0.16
11
0.43
14
0.55
R5
11
0.43
14
0.55
R36
mm
inch
R22
75
2.95
113
4.45
50
1.96
72
2.83
100
3.93
36
1.41
74
2.85
99
3.90
R1
Ø8
110
4.33
.5
DS6300 Mounting Bracket Overall Dimensions
60
2.36
30
1.18
DS6300 Overall Dimensions
mm
inch
16.5
0.65
99
3.90
63.5
2.50
104.5
4.11
85
3.35
69
2.72
113
4.45
114
4.48
102
4.01
110.3
4.34
56
2.20
mm
inch
180
7.08
DS6300 Oscillating Mirror Model Overall Dimensions
11
DS6300 QUICK REFERENCE
Focus Adjustment:
The DS6300 provides a manual adjustment of the optics to optimize the reading performance by choosing the
best focus between two extreme positions. The focus adjustment is continuous and not by step; thus, allowing an
optimum adjustment around the selected position. The relative focus positions range from 0 to 100.
The adjustment can be simply made through an external screw placed on the back of the optic HEAD and
protected by a cap. The screw may be rotated either clockwise or counterclockwise in order to move the scanner
internal lenses. In particular, a clockwise rotation causes a farther focus from the scanner, while a
counterclockwise rotation causes a nearer focus to the scanner.
An internal sensor tracks the exact laser beam focusing position allowing it to be shown on the reader display or
through the Genius™ software program.
Do not stare at the laser beam output window during this operation to avoid hazardous visible
laser light.
WARNING
Refer to the following instructions when adjusting the focus:
1)
Remove the regulation screw protecting cap (see following Figure) positioned on the back of the optic Head;
2)
Press and hold both the ▲ (up arrow) or ▼ (down arrow) key for about 2 seconds to enter the Main menu;
3)
Use the ▲ (up arrow) or ▼ (down arrow) key to select “Test Mode” item, then press the ENT (enter) key to
confirm. The reader enters Test Mode;
4)
Press the ENT (enter) key to toggle between the graphical (default) and numerical visualization of the focus
position;
Display Visualization
The first line of the display shows the read code and Good Read percentage. Possible suspending commas
at the end of the code mean that the code is too long to be displayed.
The second line of the display indicates the value of the focus position according to the table below. The
indications “Too Near” or “Too Far” are represented for values outside the focus range.
Graphical Visualization
A |---^----------| Æ where . indicates the
focus position
B N-------------| Æ where N indicates that
the focus position is
“Too Near”
C |--------------F Æ where F indicates that
the focus position is
“Too Far”
CodeRead… 100%
|------^------------------|
Graphical Visualization
Numerical Visualization
Fxxx Æ where xxx ranges from
000 to 100
TooNear
Fxxx* Æ where xxx is greater
than 100
CodeRead… 094%
F034
Normal Visualization
5)
Rotate the focus adjustment screw to reach the desired focus position. The display is refreshed with the new
values;
6)
Press the ▲ (up arrow) key to exit the Test Mode;
12
DS6300 QUICK REFERENCE
7)
Use the ▲ (up arrow) and ▼ (down arrow) key to select the “Exit” item, then press the ENT (enter) key to
confirm. The scanner exits the Main Menu and returns to its current operating mode.
Focus Adjustment Screw
The reader display shows the focus position only when the laser beam is activated.
NOTE
It is possible to visualize the focus position and the reading percentage on the terminal tool provided by the
Genius™ configuration program (see Genius™ Help On-Line for details).
Reading Diagrams:
In the following reading diagrams (0,0) is the center of the laser beam output window.
DS6300-100-0XX – Resolution: 0.20 mm/8 mils
0
0
10
6
8
10 12 14
250
8
200
6
150
4
100
2
50
0
0
-2
-50
-4
-100
-6
-150
-8
-200
16
18
20 22
24 (in)
150 200 250 300 350 400 450 500 550 600
Focus
Position = 0
(mm)
Focus
Position = 40
-10 -250
(in) (mm)
13
DS6300 QUICK REFERENCE
Reading Diagrams:
DS6300-100-0XX – Resolution: 0.30 mm/12 mils
0
0
12
300
10
250
8
200
6
150
4
100
2
50
0
0
-2
-50
8
10
12 14 16
18
20
22 24
26 28
30
32 34 (in)
200 250 300 350 400 450 500 550 600 650 700 750 800 850 (mm)
Focus
Position = 0
Focus
Position = 40
-4 -100
-6 -150
-8 -200
-10 -250
Focus
Position = 60
-12 -300
(in) (mm)
DS6300-100-0XX – Resolution: 0.50 mm/20 mils
0
0
24
600
20
500
16
400
12
300
8
200
4
100
0
0
8
12
16 20 24
Focus
Position = 60
-8 -200
-12 -300
-20 -500
-24 -600
(in) (mm)
14
32
36
40
44
Focus
Position = 100
-4 -100
-16 -400
28
48 52 54
200 300 400 500 600 700 800 900 1000 1100 1200 1300 1400
Focus
Position = 0
(in)
(mm)
DS6300 QUICK REFERENCE
Reading Diagrams:
DS6300-105-0XX (Oscillating Mirror) – Resolution: 0.20 mm/8 mils
0
0
10
250
8
200
6
150
4
100
2
50
0
0
-2
-50
-4
-100
-6
-150
-8
-200
6
8
10 12 14
16
18
20 22
24 (in)
150 200 250 300 350 400 450 500 550 600
Focus
Position = 0
(mm)
Focus
Position = 40
-10 -250
(in) (mm)
DS6300-105-0XX (Oscillating Mirror) – Resolution: 0.30 mm/12 mils
0
0
12
300
10
250
8
200
6
150
4
100
2
50
0
0
-2
-50
8
10
12 14 16
18
20
22
24
26 28
30
32 34 (in)
200 250 300 350 400 450 500 550 600 650 700 750 800 850 (mm)
Focus
Position = 0
Focus
Position = 40
-4 -100
-6 -150
-8 -200
-10 -250
-12 -300
(in) (mm)
Focus
Position = 60
15
DS6300 QUICK REFERENCE
Reading Diagrams:
DS6300-105-0XX (Oscillating Mirror) – Resolution: 0.50 mm/20 mils
0
0
24
600
20
500
16
400
12
300
8
200
4
100
0
0
8
12
16 20 24
28
32
36
40
48 52 54
44
200 300 400 500 600 700 800 900 1000 1100 1200 1300 1400
(in)
(mm)
Focus
Position = 100
Focus
Position = 60
-4 -100
-8 -200
-12 -300
-16 -400
Focus
Position = 0
-20 -500
-24 -600
(in) (mm)
Safety Precautions
1
1
2
Figure A
Figure B
1 Warning and Device Class Label
1 Laser Safety Label
2 Identification Label
1
Figure C
1 Laser Safety Label
16
DS6300 QUICK REFERENCE
The scanner is classified as a Class 2 laser product according to EN 60825-1 regulations and as a Class II laser
product according to CDRH regulations.
Disconnect the power supply when opening the device during maintenance or installation to avoid exposure to
hazardous laser light.
There is a safety device which allows the laser to be switched on only if the motor is rotating above the threshold
for its correct scanning speed.
The laser beam can be switched off through a software command (see also the Genius™ Help On-Line).
AVOID EXPOSURE - LASER LIGHT
IS EMITTED FROM THIS APERTURE
Laser Safety Label for Oscillating Mirror and Standard Models
CAUTION
LASER LIGHT
WHEN OPEN
US AD
DATALOGIC S.P.A. Via Candini, 2
40012 LIPPO DI CALDERARA (BO) ITALY
Amp.
MANUFACTURED VOLT
1.5-0.5
JANUARY 2002
10-30 DC
MODEL No.
J
N2468
R
R
SERIAL No.
EA
FA
LASER LIGHT - DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCT
MAX. OUTPUT RADIATION 1 mW
EMITTED WAVE LENGTH 630~680 nm
EN60825-1:1994
OC
.
F
AVOID EXPOSURE
TO BEAM
N
This product conforms to the applicable requirements
of 21CFR 1040 at the date of manufacture.
Warning and Device Class Label
Device Identification Label
The laser diode used in this device is classified as a Class 3B laser product according to EN 60825-1 regulations
and as a Class IIIb laser product according to CDRH regulations. As it is not possible to apply a classification
label on the laser diode used in this device, the following label is reproduced below:
LASER LIGHT
AVOID EXPOSURE TO BEAM
CLASS 3B LASER PRODUCT
MAXIMUM OUTPUT RADIATION
35 mW
EMITTED WAVE LENGTH
630~680 nm
TO EN60825-1 (1994)
Laser Diode Class Label
Any violation of the optic parts in particular can cause radiation up to the maximum level of the laser diode
(35 mW at 630 ~ 680 nm).
Power Supply
-
This product is intended to be installed by Qualified Personnel only.
All DS6300 Models:
This device is intended to be supplied by a UL Listed Power Unit marked “Class 2” or LPS power source
which supplies power directly to the scanner via the 25/26-pin connector.
17
DATALOGIC S.p.A.,
Via Candini, 2
40012 - Lippo di Calderara
Bologna - Italy
dichiara che
declares that the
déclare que le
bescheinigt, daß das Gerät
declare que el
DS6300-XXX-XXX, Laser Scanner
and all its models
e tutti i suoi modelli
et tous ses modèles
und seine modelle
y todos sus modelos
sono conformi alle Direttive del Consiglio Europeo sottoelencate:
are in conformity with the requirements of the European Council Directives listed below:
sont conformes aux spécifications des Directives de l'Union Européenne ci-dessous:
der nachstehend angeführten Direktiven des Europäischen Rats:
cumple con los requisitos de las Directivas del Consejo Europeo, según la lista siguiente:
89/336/EEC EMC Directive e
92/31/EEC, 93/68/EEC
and
et
und
y
emendamenti successivi
further amendments
ses successifs amendements
späteren Abänderungen
succesivas enmiendas
73/23/ECC Low Voltage Directive
Basate sulle legislazioni degli Stati membri in relazione alla compatibilità elettromagnetica ed alla sicurezza dei prodotti.
On the approximation of the laws of Member States relating to electromagnetic compatibility and product safety.
Basée sur la législation des Etates membres relative à la compatibilité électromagnétique et à la sécurité des produits.
Über die Annäherung der Gesetze der Mitgliedsstaaten in bezug auf elektromagnetische Verträglichkeit und Produktsicherheit
entsprechen.
Basado en la aproximación de las leyes de los Países Miembros respecto a la compatibilidad electromagnética y las Medidas
de seguridad relativas al producto.
Questa dichiarazione è basata sulla conformità dei prodotti alle norme seguenti:
This declaration is based upon compliance of the products to the following standards:
Cette déclaration repose sur la conformité des produits aux normes suivantes:
Diese Erklärung basiert darauf, daß das Produkt den folgenden Normen entspricht:
Esta declaración se basa en el cumplimiento de los productos con las siguientes normas:
EN 55022, August 1994:
LIMITS AND METHODS OF MEASUREMENTS OF RADIO DISTURBANCE CHARACTERISTICS OF INFORMATION
TECHNOLOGY EQUIPMENT (ITE)
EN 61000-6-2, April 1999:
ELECTROMAGNETIC COMPATIBILITY (EMC).
PART 6-2: GENERIC STANDARDS - IMMUNITY FOR INDUSTRIAL ENVIRONMENTS
EN 60950, October 1996:
SAFETY OF INFORMATION TECHNOLOGY EQUIPMENT, INCLUDING ELECTRICAL BUSINESS EQUIPMENT
EN 60825, March 1993:
RADIATION SAFETY OF LASER PRODUCTS, EQUIPMENT CLASSIFICATION, REQUIREMENTS AND USER’S
GUIDE
Lippo di Calderara, 16/04/2002
Ruggero Cacioppo
Quality Assurance Supervisor
821000682 (Rev. B)