Download Altinex CAT-5 to VGA + Audio Receiver DA1931CT User`s guide
Transcript
SPECIAL APPLICATION MANUAL PART NUMBER: 400-0199-003 DA1931CT CAT-5 TO VGA + AUDIO RECEIVER USER’S GUIDE SPECIAL APPLICATION TABLE OF CONTENTS Page PRECAUTIONS / SAFETY WARNINGS ..............2 GENERAL..........................................................2 INSTALLATION .................................................2 CLEANING.........................................................2 FCC / CE NOTICE..............................................2 ABOUT YOUR DA1931CT ...................................3 TECHNICAL SPECIFICATIONS...........................3 PRODUCT DESCRIPTION ..................................4 APPLICATION DIAGRAM ....................................5 DIAGRAM 1: TYPICAL CONFIGURATION ........5 DIAGRAM 2: RJ-45 PINOUT ..............................6 DIAGRAM 3: INTERNAL VIEW .........................7 DIAGRAM 4: DIP SWITCH SETTINGS..............8 INSTALLING YOUR DA1931CT...........................9 OPERATION ........................................................9 VIDEO EQUALIZATION .....................................9 TROUBLESHOOTING GUIDE ...........................10 LED IS NOT RED .............................................10 LED IS NOT GREEN ........................................10 NO SOUND......................................................10 NO REMOTE IMAGE .......................................10 RECEIVING DISPLAY QUALITY IS POOR ......11 ALTINEX POLICY ..............................................11 LIMITED WARRANTY/RETURN POLICY ........11 CONTACT INFORMATION ..............................11 400-0199-003 1 SPECIAL APPLICATION PRECAUTIONS / SAFETY WARNINGS • 1 Please read this manual carefully before using your DA1931CT. Keep this manual handy for future reference. These safety instructions are to ensure the long life of your DA1931CT and to prevent fire and shock hazard. Please read them carefully and heed all warnings. 1.1 GENERAL • Qualified ALTINEX service personnel, or their authorized representatives must perform all service. 1.2 INSTALLATION • • • • To prevent fire or shock, do not expose this unit to rain or moisture. Do not place the DA1931CT in direct sunlight, near heaters or heat radiating appliances, or near any liquid. Exposure to direct sunlight, smoke, or steam can harm internal components. Handle the DA1931CT carefully. Dropping or jarring can damage the unit. Do not pull the cables that are attached to the DA1931CT. 1.3 CLEANING • Clean only with a dry cloth. Never use strong detergents or solvents, such as alcohol or thinner. Do not use a wet cloth or water to clean the unit. Do not open the unit to clean. 1.4 FCC / CE NOTICE • This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 400-0199-003 2 This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Any changes or modifications to the unit not expressly approved by ALTINEX, Inc. could void the user’s authority to operate the equipment. SPECIAL APPLICATION ABOUT YOUR DA1931CT 2 MECHANICAL Material Finish Top Panel Height (inches) Width (inches) Depth (inches) Weight (pounds) Ship Weight (pounds) T° Operating T° Maximum Humidity MTBF (calculations) DA1931CT CAT-5 TO VGA + AUDIO RECEIVER The DA1931CT provides a means of receiving computer video and audio signals over twisted pair (CAT-5) type cable when used together with an ALTINEX Twisted Pair Video Transmitter, such as the DA1930CT. The DA1931CT is compact and easy to use. The DA1931CT is able to receive one of the video sources, such as VGA, Component Video, S-Video or C-Video along with Stereo Audio transmitted over the CAT-5/6 cable from the DA1930CT or equivalent Transmitter. Table 2. DA1931CT Mechanical ELECTRICAL DA1931CT Input CAT-5/6 Twisted Pair Video/Sync/Audio Signals Input Altinex Standard Output Video Signals RGBHV/YPbPr - Video 75 Ohms RGBHV - Sync 10 kOhms/TTL S-Video 75 Ohms Composite Video 75 Ohms Output Audio Signals Gain at 1 KHz- Balanced +6dB +/- 10% Gain at 1 KHz- Unbal. 0dB +/- 0.5dB Amplitude Matching 10% maximum (difference Left to Right) Frequency Response 20Hz-18KHz (+/-0.5dB) Power External Adapter (included) 9V DC, 1A The DA1931CT provides both Audio and Video outputs. The DA1931CT offers a female 15-pin HD output for RGBHV/YPbPr signals, a 4 pin Mini-Din connector for S-Video and an RCA connector for Composite Video Output. A 5 pin terminal block is available for balanced stereo output and a 3.5mm jack is used for unbalanced stereo output. The unit also offers hardware Video Equalization for transmission lengths up to 400 feet. The Video Equalization work in conjunction with the Video Equalization on the transmitter. There is also a Signal Detect feature which shows when an input signal is present. TECHNICAL SPECIFICATIONS FEATURES/ DESCRIPTION GENERAL Inputs Video/Audio Altinex CAT-5/6 Twisted Pair Standard Outputs RGBHV/YPbPr S-Video Composite Video Stereo Audio – unbal. Stereo Audio – balanced Compatibility 3 Table 3. DA1931CT Electrical DA1931CT RJ-45 15 Pin HD 4 Pin Mini DIN RCA female 3.5mm female 5 Pin Terminal Block VGA through UXGA, Stereo Audio, C-Video, S-Video Table 1. DA1931CT General 400-0199-003 DA1931CT 0.1” Al ALTINEX Grey Lexan Overlay 5.28in (134mm) 4.29in (109mm) 0.98in (25mm) 1.0lb (0.45kg) 1.6lbs (0.73kg) 10°C-40°C 50°C 90% non-condensing 40,000 hrs 3 SPECIAL APPLICATION PRODUCT DESCRIPTION 400-0199-003 4 4 SPECIAL APPLICATION APPLICATION DIAGRAM 5 DIAGRAM 1: TYPICAL CONFIGURATION 400-0199-003 5 SPECIAL APPLICATION DIAGRAM 2: RJ-45 PINOUT TOP 1 1 8 FRONT Pin Number RJ-45 Output Signals 1 Orange/White 2 Orange 3 Green/White 4 Blue 5 Blue/White 6 Green 7 Brown/White 8 Brown Table 1 Standard 568B Wiring Color Code 400-0199-003 6 8 SPECIAL APPLICATION DIAGRAM 3: INTERNAL VIEW VGA + AUDIO TO CAT-5 RECEIVER POWER 2.5mm 9V, 1A POWER SUPPLY OUTPUT RCA C-VIDEO SIGNAL DETECT POWER CHROMA LUMA OUTPUT 4PIN MINI DIN S-VIDEO PAIR 1 INPUT PORT RJ 45 CAT5 PAIR 2 PAIR 3 H/W EQ PAIR 4 LOOP1 PORT RJ 45 CAT5 PAIR 1 BLUE PAIR 2 RED PAIR 3 GREEN SYNC ON GREEN + + - PAIR 4 SYNC PROCESSING PAIR 1 LOOP2 PORT RJ 45 CAT5 HOR VER PAIR 2 PAIR 3 PAIR 4 LP LP R1+ R1- LP LP L1+ L1- AUDIO SEPARATOR RIGHT LEFT 400-0199-003 OUTPUT 15PIN VGA RGBHV/ Y Pb Pr 7 OUTPUT 5P TB BALANCED STEREO AUDIO OUTPUT 3.5mm UNBALANCED STEREO AUDIO SPECIAL APPLICATION DIAGRAM 4: DIP SWITCH SETTINGS The DA1931 has an internal Dip-Switch with 6 positions to achieve following features: Position Description 1 Video Gain (G=1/G=2) SW1 x1 R45 C35 Factory Default = G1. SW1 ON 1 2 3 4 5 2 6 Factory Default = OFF U16 ON V- ON V+ ON H- ON H+ R50 SOG OFF x2 Sync on Green (ON/OFF) 3, 4 HSync Polarity (Positive/Negative) 3 ON, 4 OFF = Positive (Factory Default) 3 OFF, 4 ON = Negative 5, 6 VSync Polarity (Positive/Negative) 5 OFF, 6 ON = Positive (Factory Default) 5 ON, 6 OFF = Negative C64 U15 C52 C53 D5 R114C100 C101 C51 C50 x1 C54 C35 SW1 P6 285-0382-001 RECEIVER DA1931 LED1 C89 C31 R45 R28 C-VIDEO R113 C32 R81 R112 U1 R115 P7 C68 R80 C104 R10 R59 R56 R116 R9 U25 LOOP2 U14 C120 C26 C34 R36 C36 BLUE R17 C24 U16 R34 CUT P2 R10 C65 R59 R56 U13 R57 R73 R44 R16 P13 R33 R41 C76 C44 U9 P1 C5 U8 C61 R54 R43 R3 R38 C29 R65 C59 R25 R47 C3 C87 C62 R61 C56 C57 R35 R21 R31 R12 C28 C117 U7 L1 R118 C116 SW3 P9 P8 R37 R60 C118 R64 C91 x2 R13 R1 C55 C58 CUT R2 C1 J1 VIDEO GAIN RED R24 C78 U11 R49 R48 R71 P10 P11 R42 C2 R58 INPUT CUT R4 C4 R14 R53 R72 RGBHV/ YPbPr R26 R19 C75 U12 R55 R15 R62 C60 GREEN C6 C119 C66 P12 Q4 C72 R66 C63 R11 LOOP1 C23 C108 C64 R9 R5 R117 ON V- ON V+ ON H- SOG x2 R50 ON H+ R6 S-VIDEO R68 R69 C103 x1 D2 D1 C110 C111 -6V CUT C115 U19 P5 C90 C16 R97 C99 C47 C30 R95 C96 R92 C85 U3 C82 C79 C10 R52 C84 R104 U22 C113 U2 C69 U23 R109 R90 R87 R93 C40 C81 R86 R85 C33 C80 R88 R84 C14 C71 C112 8 R110 R67 C114 C67 C70 R89 R91 R105 VIDEO EQ C42 C95 C46 C9 C83 U4 C12 AUDIO 400-0199-003 R22 R83 TP2 C39 C74 C13 P3 R27 R63 C45 C49 TP1 C18 C98 R98 R96 R29 C11 R30 C25 U26 R94 R100 C92 R106 R51 C97 R108 R46 U5 C107 R99 C38 R103 C27 C41 C15 C106 R101 C93 R8 R39 U10 C43 C22 C21 R23 U27 U20 U18 C102 R102 R32 R107 U21 OGI AUDIO C109 R40 R74 C77 C8 C7 R7 C86 C17 U6 C37 C94 POWER C105 C73 R82 P4 U17 C19 C20 C48 SPECIAL APPLICATION INSTALLING YOUR DA1931CT 6 OPERATION Step 1. Determine the settings required for Gain, Sync On Green, Horizontal Sync Polarity and Vertical Sync Polarity. If necessary to change the factory defaults, open the unit and set the switches per DIAGRAM 4 on page 8. The DA1931CT requires only one adjustment to be made for optimal performance. Video Equalization is required for long cable lengths and may be adjusted to fine tune the video display. 7.1 VIDEO EQUALIZATION Video Equalization is provided to fine tune the displayed image on the remote display. Typically, for short cable runs the equalization will be set to near minimum. Cable lengths up to 400 feet will require near maximum equalization. Step 2. Plug the 9V power adapter into an AC outlet and then connect the other end to the POWER input jack on the DA1931CT. Step 3. Verify the LED near the top of the unit is illuminated RED indicating power is applied. The equalization adjustments on the DA1931CT Receiver and DA1930CT Transmitter work together to provide equalization for maximum cable lengths. For example, for cable runs less than 50 feet, both equalization settings may be set to approximately minimum, since on the short distances no equalization is required. Where as cable runs of 400 feet will see equalization settings at about the three-quarter position. Step 4. Connect the CAT-5/6 cable from the video output of the CAT-5 Transmitter to the CAT-5 Input port on the DA1931CT. Step 5. Verify the power LED at the top of the unit changes to GREEN, indicating a SYNC signal has been detected. Step 6. Connect the stereo audio output from the DA1931CT to the audio receiving device. Step 7. Connect the receiving monitor to the applicable DA1931CT Video Output connector, either RGBHV/YPbPr, S-Video or C-Video depending on the input type to the transmitter. Step 8. Verify the picture quality on the receiving monitor is equivalent to the quality as displayed on the local monitor at the transmitter. If the quality of the image is poor or non-existent, it may be necessary to adjust the Video Equalization on the DA1931CT and/or DA1930CT. See the OPERATION section that follows for details. 400-0199-003 7 9 SPECIAL APPLICATION TROUBLESHOOTING GUIDE 8.3 NO SOUND 8 We have carefully tested and have found no problems in the supplied DA1931CT. However, we would like to offer suggestions for the following: Cause 1: The source has a problem. Solution: Check the source and make sure that there is a signal present and all source connections are correct. If the source is working and there is still no sound, see Cause 2. Cause 2: The volume is too low. Solution: Increase the AUDIO GAIN toward maximum. If there is still no sound present, see Cause 3. Cause 3: Cable connections are incorrect. Solution: Make sure that cables are properly connected. Also, make sure that the continuity and wiring are good. If there is still no sound, see Cause 4. 8.1 LED IS NOT RED The LED should be ON and RED when power is applied and there is no video signal present. If the LED is ON and GREEN, the unit is receiving power and a SYNC signal. Cause 1: No AC power. Solution: Verify the adapter is plugged into a working AC outlet and that the outlet has power. Cause 2: Adapter is DA1931CT. not plugged into Solution: Verify the DC power plug coming from the AC adapter is plugged all the way into the DA1931CT. Cause 4: The receiving problem. Cause 3: The DA1931 has a problem. Solution: Solution: If there is AC power to the adapter and the LED still does not turn on, the DA1931CT or the power adapter may require service. Call ALTINEX at (714) 990-2300. Make sure the receiving device has power and is turned ON. If there is still no sound, please call Altinex at (714) 990-2300. There is no power. Solution: Disconnect the video input from the DA1931CT and verify the LED is ON and RED indicating power is present. Reconnect the computer's video output. If the LED is still not GREEN see Cause 2. Cause 2: There is no Sync signal. Solution: Verify the computer output is operating correctly by connecting it directly to a monitor. If the display is good, call ALTINEX at (714) 990-2300. 400-0199-003 has a 8.4 NO REMOTE IMAGE 8.2 LED IS NOT GREEN Cause 1: device Cause 1: The source has a problem. Solution: Check the image on the local monitor and verify the quality is good. If the local image is good, see Cause 2. Cause 2: Video equalization required. Solution: Adjust the VIDEO EQUALIZATION on the DA1931CT. Long cable runs may require adjustment on both the DA1930CT and the DA1931CT. In general, cable runs less then 50 feet require little or no video equalization and should be set to minimum. Cable runs up to 400 feet will require maximum equalization on both the transmitter and receiver. 10 SPECIAL APPLICATION 8.5 RECEIVING DISPLAY QUALITY IS POOR Cause 1: The source has a problem. Solution: Check the image on the local monitor and verify the quality is good. If the local image is good, see Cause 2. Cause 2: Video equalization required. Solution: Adjust the VIDEO EQUALIZATION on the DA1931CT. Long cable runs may require adjustment on both the DA1930CT and the DA1931CT. If the image is still not correct, call ALTINEX at (714) 990-2300. ALTINEX POLICY 9.1 LIMITED WARRANTY/RETURN POLICY Please see the Altinex website at www.altinex.com for details on warranty and return policy. 9.2 CONTACT INFORMATION ALTINEX, INC 592 Apollo street Brea, CA 92821 USA TEL: 714 990-2300 TOLL FREE: 1-800-ALTINEX WEB: www.altinex.com E-MAIL: [email protected] 400-0199-003 9 11