Download Elta ST104N Instruction manual
Transcript
INSTRUCTION MANUAL ® Orion IntelliScope Computerized Object Locator ™ #7880 Providing Exceptional Consumer Optical Products Since 1975 Customer Support (800) 676-1343 E-mail: [email protected] Corporate Offices (831) 763-7000 P.O. Box 1815, Santa Cruz, CA 95061 IN 229 Rev. B 3/11/04 Coil cable jack RS-232 jack Backlit liquid crystal display Illuminated pushbuttons User-friendly keypad Figure 1. The IntelliScope Computerized Object Locator. 2 Congratulations on your purchase of the Orion IntelliScope™ Computerized Object Locator. When used with any of the SkyQuest IntelliScope XT Dobsonians, the object locator (controller) will provide quick, easy access to thousands of celestial objects for viewing with your telescope. The controller’s user-friendly keypad combined with its database of more than 14,000 celestial objects put the night sky literally at your fingertips. You just select an object to view, press Enter, then move the telescope manually following the guide arrows on the liquid crystal display (LCD) screen. In seconds, the IntelliScope’s high-resolution, 9,216step digital encoders pinpoint the object, placing it smack-dab in the telescope’s field of view! Easy! Compared to motor-dependent computerized telescopes systems, IntelliScope is faster, quieter, easier, and more power efficient. And IntelliScope Dobs eschew the complex initialization, data entry, or “drive training” procedures required by most other computerized telescopes. Instead, the IntelliScope setup involves simply pointing the scope to two bright stars and pressing the Enter key. That’s it — then you’re ready for action! These instructions will help you set up and properly operate your IntelliScope Computerized Object Locator. Please read them thoroughly. Table of Contents 1. Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2. Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 3. Overview of Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 4. Locating the Planets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 5. Locating Deep-Sky Objects by Catalog . . . . . . . . . . . . . . . . . . . . 12 6. Locating Deep-Sky Objects by Object Type . . . . . . . . . . . . . . . . . 14 7. Locating Stars . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 8. Tours of the Best Objects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 9. The Identity Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 10. Adding User-Defined Objects . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 11. The FCN Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 12. The “Hidden” Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 13. Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Appendix A: Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-25 Appendix B: Alignment Star Finder Charts . . . . . . . . . . . . . . . . . 26-29 Appendix C: Constellation Abbreviations . . . . . . . . . . . . . . . . . . . . . 30 Appendix D: ST Catalog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31-46 3 Parts List Your IntelliScope™ Computerized Object Locator comes with the following parts: Qty. Description 1 Object locator computer (controller) 1 Altitude encoder assembly 1 Coil cable 1 Altitude encoder cable (53" long) 1 Azimuth encoder cable (24" long) 6 Wire retaining clips 2 Hook-and-loop strips (1 “hook” strip, 1 “loop” strip) 1 Plastic bumper 3 Wood screws 2 Nylon washers 1 9-volt battery The only tool needed for installation is a Phillips-head screwdriver. Remove the optical tube from the base to begin installation. Note: The IntelliScope Computerized Object Locator is only compatible with Orion SkyQuest XT IntelliScope Dobsonians. If you have another Dobsonian, or any other telescope, the IntelliScope system will not function properly. 1. Installation 1) Install the altitude encoder assembly onto the base’s right side panel. This is the side of the base opposite the side with the IntelliScope Computerized Controller Port. Below the 5/8" through-hole in the panel, there are two predrilled starter holes in the inwardfacing surface (Figure 2). Take two of the supplied wood screws and push them through the two slotted holes in the bottom of the altitude encoder’s computer board. The screw heads should be on the same side as the altitude encoder’s modular jack. Now, with the screws pushed through the encoder board, place a nylon washer on the end of each screw (Figure 3). Then, thread the screws into the starter holes in the side panel. The shaft on the altitude encoder assembly should protrude through the 5/8" through-hole in the side panel. It will take a bit of dexterity to keep the washers on the ends of the screws when installing, so don’t get frustrated if it takes a couple tries. The screws should not be fully tightened; they should be tight, but not tight enough to prevent the altitude encoder from moving up and down within the slots in the encoder board. 2) There is a pilot hole above the 5/8" through hole in the right side panel’s interior surface; this is where the plastic bumper that protects the altitude encoder assembly will be installed. Take the remaining wood screw, push it through the bumper, and thread it into the pilot hole until tight (Figure 4). 3) Connect one end of the azimuth encoder cable (the shorter of the two cables) to the encoder jack in the top baseplate of the Dobsonian base. Connect the other end to the 4 encoder connector board that should be already installed on the base’s left side panel. The cable should plug into the jack on the left side of the encoder connector board (see Figure 5). Altitude encoder pilot holes 4) Connect one end of the altitude encoder cable to the modular jack on the altitude encoder assembly. Connect the other end of the cable to the jack on the right side of the encoder connector board (see Figure 5). Figure 2. The two pilot holes used to mount the altitude encoder assembly are located on the interior surface of the right side panel of the base. Modular jack Altitude encoder assembly Nylon washers 5) Use the provided wire clips to secure the altitude and azimuth cables neatly to the base. We recommend using two clips for the (shorter) azimuth cable, and four clips for the (longer) altitude cable (Figure 5a.). The clips have adhesive backing; simply peel the paper off the back of the clip and press the adhesive back to the base where you want the clip to be located. 6) Place the telescope optical tube into the base. Be very careful not to hit the altitude encoder with the side bearing on the tube when doing this or damage to the encoder could result. The bumper helps to prevent such contact. 7) Reinstall the telescope’s tensioning knob (the one with the Teflon and metal washers) through the base’s left side panel (the side that has the IntelliScope Computerized Controller Port label) and into the threaded hole in the center of the tube’s side bearing. Wood screws Figure 3. Place a nylon washer on the end of each screw after the screws are pushed through the altitude encoder assembly. 8) Reinstall the telescope’s retaining knob, without its black nylon bushing, through the altitude encoder’s aluminum shaft (now protruding from the right side panel) and into the tube’s side bearing (Figure 6). Make sure this knob is fully tightened. 9) Insert one end of the coil cable into the larger of the two jacks on the top of the IntelliScope controller (Figure 1). Insert the other end into the “IntelliScope Computerized Controller Port” on the left side of the Dobsonian base. Figure 4. Install the bumper into the pilot 10) Two hook-and-loop strips (one strip of “hooks” and one strip of “loops”) have been provided to hang the IntelliScope controller in a convenient location on the base when not in use. Place the “hooks” strip on the hole above the altitude encoder assembly. 5 Altitude cable jack Figure 6. The retaining knob now goes Azimuth cable jack Figure 5. The azimuth cable plugs into the jack on the left of the encoder connector board. The altitude cable plugs into the jack on the right. through the shaft of the altitude encoder assembly before threading into the side bearing on the telescope tube. back of the controller, and the “loops” strip on the base in a convenient spot. Make certain the location of the strip on the base will not cause the controller to interfere with the motions of the mount. You may want to consider using the optional holster instead of the supplied hook-and-loop strips. The holster is a metal holder custom-designed to fit the IntelliScope controller. When installed at the top of the Dobsonian base, it provides a firm mounting for the controller at a convenient position for easy access. The controller can be removed from the holster when needed or kept in the holster during use. 11) Slide the battery cover off the back of the hand control and insert the 9-volt alkaline battery. Make sure the positive and negative terminals of the battery are oriented as shown in the bottom of the battery compartment. Replace the battery cover. Your IntelliScope Computerized Object Locator is now installed and ready to be used. Figure 5a. Use the wire clips to secure the cables neatly to the base 6 2. Alignment This section will familiarize you with the alignment procedure for the IntelliScope system. Powering the Controller To turn the controller on, firmly press the Power button. The LED lights will activate and the LCD screen will display its introduction message. The intensity of the illumination can be adjusted by repeatedly pressing the Power button. There are five levels of LED brightness. Choose a brightness level that suits your conditions and needs. (Dimmer settings will prolong battery life.) To turn the controller off, press and hold the Power button for a few seconds, then release it. To conserve battery life, the controller is programmed to shut itself off after being idle for 15 minutes. So, make sure to press a button at least once every 15 minutes if you do not want the controller to turn off. If the controller does turn off, you will need to perform the initial alignment procedure again. If the LCD screen and the buttons’ backlighting automatically begin to dim, it’s time to change batteries. Initial Vertical Alignment After powering up the controller, the top line of the LCD display will read: “POINT VERTICAL.” If the vertical stop you installed on the Dobsonian base during assembly of the telescope is properly adjusted (see below), simply rotate the telescope upwards in altitude until the bottom of the tube comes into contact with the vertical stop. Once the telescope tube is in the vertical position, press the Enter button to start the two-star alignment procedure. Adjusting the Vertical Stop In order for the IntelliScope system to work accurately, the vertical stop must be precisely adjusted so that the optical tube is truly perpendicular to the azimuth axis of the base when the controller says “POINT VERTICAL.” For most IntelliScopes, the vertical stop must use the nylon spacer, one of the 1/16"-thick washers, and the 1/32"-thick washers to achieve this. These parts, plus an extra 1/16"-thick washer are supplied with the Dobsonian base. If you do not have access to a carpenter’s level, then using the spacer, 1/16"-thick washer, and 1/32"-thick washer will be the best you can do to adjust the vertical stop. For the most precise adjustment of the vertical stop (which will allow the best pointing accuracy to be achieved), you should use a carpenter’s level. Any hardware store will have one. First, make sure the base itself is level. Place the carpenter’s level on the top ground board and rotate the base 180˚ in azimuth (Figure 7). The level should indicate that the base is level through the entire rotation. If not, then reposition the base on the ground, or place shims underneath the feet until the base stays level though a 180˚ rotation. Figure 7. Place a carpenter’s level on the base as shown. The base should stay level through a 180˚ rotation in azimuth. Once the vertical stop is set, the base does not need to be level to function properly. 7 Next, place the nylon spacer, the 1/16"-thick washer, and the 1/32"-thick washer on the vertical stop screw, and thread the entire assembly into the insert in the base’s front brace. Now, rotate the telescope upwards in altitude until the mirror cell of the telescope comes into contact with the vertical stop. Place the carpenter’s level across the top of the telescope (see Figure 8). Is the top of the tube level? If so, you are finished adjusting the vertical stop. If not, add or remove a washer to the vertical stop screw until the top of the tube is level when the mirror cell comes into contact with the vertical stop. Figure 8. Once the base is leveled, point the tube up until the mirror cell comes into contact with the vertical stop. Then, place the carpenter’s level across the top of the tube as shown. If the vertical stop is set properly, the top of the tube should also be level. Once the vertical stop is accurately adjusted, it should not need adjustment again. The base does not need to be level for the IntelliScope system to function properly; the base only needs leveling when initially setting the vertical stop. Simple Two-Star Alignment After setting the vertical position of the optical tube, a simple two-star alignment process is all that is needed to ready the IntelliScope system for operation. This is a great simplification from other computerized systems, which require you to enter data such as your longitude, latitude, and time zone. For the IntelliScope controller to accurately find objects, you only need to center two bright stars in your telescope and indicate to the controller which two stars you have centered. This is quite easy to do. For your convenience, we have provided finder charts for the alignment stars in Appendix B. Use the finder chart to locate and identify two bright stars in your current night sky. For best results, choose two stars that are at least 60˚ apart from each other. (The width of your fist at arm’s length is about 10˚, so you want the stars to be at least six fist-widths apart.) So, the optical tube is now in the vertical position and you’ve chosen two bright stars in the sky to use for alignment. The telescope should have a high power eyepiece, such as the 10mm Sirius Plössl, in the eyepiece holder and the finder scope should be properly aligned with the telescope (these procedures are described in your telescope’s manual). The LCD screen will state on its top line “ALIGN STAR 1,” with the name of a star flashing on the second line. Use the arrow buttons to scroll through the names of the alignment stars. The up arrow button scrolls through the stars alphabetically from A to Z. The down arrow button scrolls alphabetically backwards, from Z to A. When you arrive at the name of the star you wish to align on, you can begin to move the telescope so that it is pointing at that star (but don’t press the Enter button yet). Note: The controller will not accept Polaris as the first alignment star. This helps prevent the pointing accuracy from decreasing over time. It is OK to use Polaris as the second alignment star, however. Take hold of the “navigation knob” on the optical tube and move the telescope so that it is pointing in the general area of the alignment star. Aim the telescope so the alignment star appears in finder scope. Be careful not to confuse the alignment star with other stars in the area when doing this. (It will likely be the brightest star in the field of view.) Now, 8 move the telescope until you have centered the star on the crosshairs of the finder scope. Look into the eyepiece of the telescope, and you should see the alignment star in the field of view of the eyepiece. If it isn’t, then your finder scope is out of alignment with your telescope and will need to be adjusted. Once the alignment star is in the eyepiece’s field of view, center it in the eyepiece as best you can by making small movements to the telescope. (If you have one, an illuminated reticle eyepiece is great for centering alignment stars). Once this is done, press the Enter button on the controller. You have now completed one-half of the two-star alignment. The LCD screen will now read “ALIGN STAR 2” on the first line with an alignment star’s name flashing on the second line. As before, scroll through the names of the stars with the arrow buttons until you reach your second chosen alignment star. Repeat the procedure described above for your second alignment star. When you have aligned on the second star, press the Enter button. The LCD will then display a number. It is the alignment error factor, or “warp” (W) factor. The Alignment Error (Warp) Factor The “warp” alignment error factor essentially lets you know if your alignment was accurate or not. Ideally, this number should be as low as possible, but any “W” of 0.5 or smaller is acceptable (regardless of + or - sign). Warp factors of ±0.3 and ±0.4 are the most common. Warp factors under ±0.2 are typically not achievable. If you complete an alignment and the warp factor is larger than ±0.5 (e.g., +0.6, -0.6, +0.7, -0.7, etc.), then you must turn the controller off (by holding down the Power button) and begin the alignment procedure again. Otherwise, there is no guarantee that the controller will consistently place objects within the field of view of a medium-low power eyepiece. An unacceptable warp factor may indicate that you aligned on the wrong star or did not have the telescope initially in a precisely vertical position. If you are having problems getting the warp factor at or below ±0.5, see the troubleshooting section in Appendix A. Your IntelliScope Computerized Object Locator is now ready to find objects. Replace the high- powered eyepiece you used for centering the alignment stars with a low-power, wide-field eyepiece, such as the 25mm Sirius Plössl. 3. Overview of Controller The IntelliScope Computerized Object Locator has been specifically designed for ease of use. This section will help familiarize you with the basic layout and operation of the controller. Pushbuttons Besides the Power, Enter, ID, FCN, and up/down arrows, all pushbuttons have letters on them with numbers above them. The letters designate the function of the pushbutton. The numbers above them are used for entering numerical data only; the numbers are never active until a function is first chosen. The numbers are arranged like a telephone keypad for ease of number entry. None of the function buttons will work properly until an initial alignment, as outlined previously, is completed. If you press a function button before the two-star alignment is completed, the controller will display “MUST STAR ALIGN.” Turn the unit off, then on again (by using the Power button), to begin the alignment routine again. The Guide Arrows The controller leads you to astronomical targets with guide arrows displayed on the LCD screen. After an object is selected to view, you will see two guide arrows, one that points 9 left or right, and one that points up or down. Move the telescope tube in the corresponding direction of the guide arrows. If you are standing to the left of the telescope and facing the same direction the telescope is pointed, the guide arrows will exactly correspond with the direction you should move the telescope (Figure 9). Otherwise, if an up arrow is displayed, move the telescope tube upward, if a down arrow is displayed, move the telescope tube downward, if a left arrow is displayed, rotate the telescope counterclockwise, and if a right arrow is displayed, rotate the telescope clockwise. There is a number next to each guide arrow that indicates how far the telescope needs to be moved to reach the selected object. Figure 9. If you stand to the left of the As you move the telescope toward the telescope, and face the direction the tube is object, this number will decrease. When pointing, the guide arrows will correspond the number goes below ten, the figure will exactly with the direction you should move the be displayed in tenths; this helps to make telescope in order to find the selected object. small, precise movements to the telescope tube in order to bring the object into your field of view. When both numbers reach zero, stop moving the telescope. The object will be within the field of view of a medium-low power eyepiece (25mm focal length or longer). For example, look at Figure 10a, which shows an LCD screen for someone trying to locate M51, otherwise known as the Whirlpool Galaxy. The first arrow is pointing right and gives a number of 34. The second arrow is pointing up and displays the number 12. This means that the telescope tube should be moved to the right (clockwise) and up. When you are close to M51, the numbers will be displayed in tenths, as is shown in Figure 10b. When the numbers reach zero (Figure 10c), the telescope will be pointed right at the Whirlpool Galaxy. a. b. c. Figure 10a-c. This sequence of pictures illustrate how the controller’s guide arrows will look as you are finding an object. (a.) When you are far away from the object, there will be a number (from 10 to 179) to the left of the guide arrows. (b.) When you are close to the object, each guide arrow will display a number on its immediate left (from 0 to 9) and immediate right (from 0 to 9); the number on the left is whole number increments, while the number on the right is in increments of tenths. This helps in making small movements to the telescope to pinpoint the object’s location. (c.) When the guide arrows display “0.0 0.0”, the object will be within the field of view of the telescope (with a 25mm or longer focal length eyepiece). 10 It is easiest to move the telescope in one direction at a time (say altitude) until the corresponding number reached “0.0”. Then move the scope in the other direction (azimuth) until that number also reads “0.0”. If the object selected to view is currently located below the horizon, the word “HORIZON” will flash before the guide arrows are displayed. Choose another object to view. 4. Locating the Planets By far the most popular objects for viewing, after the Moon, are the planets. Since the other eight planets in our solar system are also orbiting the Sun, they do not appear in fixed positions in the night sky like deep-sky objects and stars do. Because of this, the controller requires you to input the date before it can find the planets. To find planets with your IntelliScope Computerized Object Locator, use the following procedure: 1) Press the Planet button on the controller. 2) The LCD screen will display a date similar to the following: DATE 01 JUN 2003 3) The number after the word “DATE” will be flashing and represents the day of the month. Input the two-digit day using the number buttons. 4) The three-letter month will now be flashing. Use the arrow buttons to scroll to the present month and then press the Enter button. 5) Now the year will flash. Input the year using the number buttons. If you make a mistake while inputting the date, press the Enter button at any time while still within the Planet button function. The LCD screen will then display the last date input, with the two-digit day after the word “DATE” flashing. Input the correct date as outlined above. Now, to choose a planet to view, press the arrow buttons and scroll through the planets. The planet’s name will be displayed in the upper left section of the LCD screen, with the guide arrows on the upper right of the LCD screen. Move the telescope in the corresponding direction shown by the guide arrows. The lower left screen shows the constellation that the planet appears in, with its present co-ordinates given in right ascension and declination. When you are finished viewing the planet, you may scroll to another planet by using the arrow buttons. The features and details you can see will vary from planet to planet. The following descriptions give a brief overview of what to expect when viewing them: MERCURY Mercury is often so close to the Sun that it cannot be seen. Sometimes it is visible for a brief period after the Sun sets, and sometimes it’s visible in the morning just before the Sun rises. Mercury does not really show any detail, but is quite bright. With your telescope, you will be able to investigate this planet’s orange-colored hue. Like Venus, Mercury sometimes appears as a crescent, rather than as a full disk. VENUS At its brightest, Venus is the most luminous object in the sky, excluding the Sun and the Moon. It is so bright that sometimes it is visible to the naked eye during full daylight! Ironically, Venus appears as a thin crescent, not a full disk, when at its peak brightness. Because it is close to the Sun, it never wanders too far from the morning or evening 11 horizon. No surface markings can be seen on Venus, which is always shrouded in dense clouds. MARS The Red Planet makes its closest approach to Earth every two years. During close approaches you’ll see a red disk, possibly some light and dark regions, and maybe the polar ice cap. To see surface detail on Mars, you will need a high power eyepiece and very steady air! JUPITER The largest planet, Jupiter, is a great subject for observation. You can see the disk of the giant planet and watch the ever-changing positions of its four largest moons — Io, Callisto, Europa, and Ganymede. Higher power eyepieces should bring out the cloud bands on the planet’s disk and maybe even the Great Red Spot. SATURN The ringed planet is a breathtaking sight when it is well positioned. The tilt angle of the rings varies over a period of many years; sometimes they are seen edge-on, while at other times they are broadside and look like giant “ears” on each side of Saturn’s disk. A steady atmosphere (good seeing) is necessary for a good view. You will probably see a bright “star” close by, which is Saturn’s brightest moon, Titan. URANUS Uranus is a faint planet, and requires high powers (at least 100x) before it starts to show any detail that distinguishes it from stars. Uranus will appear as a pale, blue-green disk. NEPTUNE Like Uranus, Neptune will require high powers before showing anything to distinguish itself from stars. Neptune will appear as a bluish-colored disk, possibly with a very faint moon nearby if you are using a larger-aperture IntelliScope. PLUTO Smaller than our own Moon, Pluto is very, very faint and shows little more than a point of light similar to a star. Even the Hubble Space Telescope is unable to show much detail on Pluto. Many amateur astronomers note how Pluto moves with respect to background stars (over several nights) in order to confirm their observation of our most remote planet. 5. Locating Deep-Sky Objects by Catalog Catalogs are groups of deep sky objects of interest that have been assembled and given designations. Very often a deep-sky object will have a catalog number, as well as a “common” name. For example, the Orion Nebula is listed in the Messier catalog as “M42.” The controller has three catalogs built-in: The Messier catalog (M), the New General Catalog (NGC), and the Index Catalog (IC). Many of the objects in the Messier catalog also have NGC catalog designations. The Messier Catalog The Messier catalog contains 110 galaxies, nebulas, and star clusters identified by the famous French astronomer Charles Messier and his colleagues in the late 1700’s. These are some of the most popular celestial attractions observed by amateur astronomers. To view an object from the Messier catalog, press the M button. Then enter the number of the Messier object you wish to view using the numeric buttons and press the Enter button. For example, to view Messier 57, also known as “the Ring Nebula,” you would press the M button, then press the “5” button, then press the “7” button, followed by the Enter button. If the number of the Messier object you wish to view contains three digits, it is not necessary to press Enter after inputting the third digit. 12 The object’s catalog designation will be shown in the upper left corner of the display screen, with the guide arrows in the upper right. The lower left will display the constellation the object resides in and the object’s common name (if it has one) or a brief description of the object. Move the telescope in the corresponding directions shown by the guide arrows to locate the object. You can get more information about the selected object by pressing the Enter button. The second line of the LCD display will then cycle information about the object you are viewing such as its celestial coordinates (R.A. and Dec.), magnitude (brightness), size (in arc-minutes or arc-seconds), and a brief scrolling text description. When you are finished viewing the selected Messier object, you may scroll to another Messier object by using the arrow buttons, or you can select another Messier object to view by pressing the M button again. The New General Catalog The New General Catalog, or NGC, is a catalog of some 7,840 deep-sky objects compiled by the Danish astronomer J. L. E. Dreyer more than 100 years ago. It contains hundreds of excellent examples of each type of deep-sky object and is the most well known and used catalog by amateur astronomers beyond the already mentioned Messier catalog. To be more precise, the version of the New General Catalog used in the IntelliScope Computerized Object Locator is an improved version known as the “Revised New General Catalog”; this version has many corrections from Dreyer’s original list. To view an object from the NGC catalog, press the NGC button. Then enter the number of the NGC object you wish to view using the numeric buttons and press Enter. For example, to view the Andromeda Galaxy, which is listed as NGC224, you would press the NGC button, then the “2” button twice, then the “4” button, followed by the Enter button. If the number of the NGC object you wish to view contains four digits, it is not necessary to press Enter after inputting the fourth digit. The object’s catalog designation will be shown in the upper left corner of the LCD screen, with the guide arrows in the upper right. The lower left will show the constellation the object resides in, and the object’s common name (if it has one) or a brief description of the object will be shown in the lower right. Move the telescope in the corresponding directions shown by the guide arrows. You can get more information about the selected object by pressing the Enter button. The second line of the LCD display will then cycle information about the object you are viewing such as its celestial coordinates (R.A. and Dec.), magnitude (brightness), size (in arcminutes or arc-seconds), and a brief scrolling text description. When you are finished viewing the selected NGC object, you may scroll to another NGC object by using the arrow buttons, or you can select another NGC object to view by pressing the NGC button again. The Index Catalog The Index Catalog, or IC, contains 5,386 objects discovered in the decade or so after the NGC catalog was first published. This list contains objects similar to the NGC, but IC objects are typically fainter and more difficult to observe. To view an object from the IC catalog, press the IC button. Then input the number of the IC object you wish to view using the numeric buttons and press the Enter button. For example, to view the Flaming Star Nebula, which is listed as IC405, you would press the IC button, then the “4” button, then the “0” button, then the “5” button, followed by the 13 Enter button. If the number of the IC object you wish to view contains four digits, it is not necessary to press Enter after inputting the fourth digit. The object’s catalog designation will be shown in the upper left corner of the LCD screen, with the guide arrows in the upper right. The lower left will show the constellation the object resides in, and the object’s common name (if it has one) or a brief description of the object will be shown in the lower right. Move the telescope in the corresponding directions shown by the guide arrows. You can get more information about the selected object by pressing the Enter button. The second line of the LCD display will then cycle information about the object you are viewing such as its celestial coordinates (R.A. and Dec.), magnitude (brightness), size (in arcminutes or arc-seconds), and a brief scrolling text description. When you are finished viewing the selected IC object, you may scroll to another IC object by using the arrow buttons, or you can select another IC object to view by pressing the IC button again. 6. Locating Deep Sky Objects by Object Type Rather that trying to select objects by catalog numbers, you may wish to simply view certain types of objects. This is where the Nebula, Galaxy, and Cluster buttons come in handy. These buttons will access a selection of the best and brightest nebulas, galaxies, and star clusters in the night sky. The Nebula, Cluster and Galaxy buttons are organized by constellation. So, before using these buttons, decide in which constellation you would like to view an object. Choose a constellation that is at least 40˚ high in the sky to get a good view. If you are unsure of the constellations currently visible in your night sky, consult a planisphere or the monthly star chart at telescope.com. Locating Nebulas Amongst the most beautiful objects in the night sky, nebulas are clouds of dust and gas that are lit by a nearby stellar source. There are several different types of nebulas; emission nebulas, which are where star systems form, planetary nebulas, which are the result of a star dying, and reflection nebulas, which are caused by dust reflecting starlight. Most have low surface brightness, so a dark sky free of light-pollution is best for a night of viewing nebulas. To view a nebula, press the Nebula button on the controller. The LCD screen will then display the word “NEBULA” with a flashing three-letter constellation designation after it. Now, select the constellation in which you would like to view a nebula. Use the arrow buttons to scroll through the list of constellations. If you are unsure which constellation the three-letter designation represents, refer to Appendix C. Once you have selected the constellation, press Enter. A nebula in that constellation will now appear on the LCD screen, along with the guide arrows to lead you to the nebula. The current constellation is shown in the lower left, and the nebula’s proper name or catalog number is in the lower right. For more information about the nebula selected, press the Enter button. To go to the next nebula in the selected constellation, simply press the up arrow button. The guide arrows will now direct you to the next nebula in the constellation. If there are no more nebulas available in that constellation, a nebula from the next constellation (in 14 alphabetical order) will be displayed. To select another constellation in which to view nebulas, press the Nebula button again. Locating Star Clusters Star clusters are just what their name implies; groupings of stars. Star clusters come in two main types, open and globular. Open star clusters reside within our Milky Way galaxy and usually contain a handful of stars clustered together because they were spawned from the same gas cloud. Globular clusters are more like miniature galaxies, with hundreds or thousands of stars packed into a spherical shape by mutual gravity. Globular clusters reside outside the disk of the Milky Way galaxy and orbit the galaxy’s center. It is believed that globular clusters are formed as a natural consequence of galaxy formation. Star clusters, in general, are somewhat bright compared to other deep-sky objects, so many will appear quite spectacular, even in the smaller telescopes. To view a star cluster, press the Cluster button on the controller. The LCD screen will then display the word “STAR CLUSTER” with a flashing three-letter constellation designation after it. Now, select the constellation in which you would like to view a star cluster. Use the arrow buttons to scroll through the list of constellations. If you are unsure which constellation the three- letter designation represents, refer to Appendix C. Once you have selected the constellation, press Enter. A star cluster in that constellation will now appear on the LCD screen, along with the guide arrows to lead you to the star cluster. The current constellation is shown in the lower left, and the star cluster’s proper name or catalog number is in the lower right. For more information about the star cluster selected, press the Enter button. To go to the next star cluster in the selected constellation, simply press the up arrow button. The guide arrows will now direct you to the next star cluster in the constellation. If there are no more star clusters available in that constellation, a star cluster from the next constellation (in alphabetical order) will be displayed. To select another constellation in which to view a star cluster, press the Cluster button again. Locating Galaxies Nebulas may be beautiful and star clusters impressive, but nothing has quite the breathtaking power of observing a galaxy. Galaxies are collections of billions of stars that come in a variety of shapes and sizes. Viewing a galaxy always gives the observer a revelation of just how vast our universe truly is. Keep in mind, however, that most galaxies are quite faint, and may be challenging to identify, especially in smaller telescopes. To view a galaxy, press the Galaxy button on the controller. The LCD screen will then display the word “GALAXY” with a flashing three-letter constellation designation after it. Now, select the constellation in which you would like to view a galaxy. Use the arrow buttons to scroll through the list of constellations. If you are unsure which constellation the three-letter designation represents, refer to Appendix C. Once you have selected the constellation, press Enter. A galaxy in that constellation will now appear on the LCD screen, along with the guide arrows to lead you to the galaxy. The current constellation is shown in the lower left, and the galaxy’s proper name or catalog number is in the lower right. If you wish to have more information about the galaxy selected, press the Enter button. To go to the next galaxy in the selected constellation, simply press the up arrow button. The guide arrows will now direct you to the next galaxy in the constellation. If there are no more galaxies available in that constellation, a galaxy from the next constellation (in alphabetical order) will be displayed. To select another constellation in which to view galaxy, press the Galaxy button again. 15 7. Locating Stars The IntelliScope database contains 837 stars. Stars always appear like tiny points of light. Even powerful telescopes cannot magnify a star to appear as more than a point of light! You can, however, enjoy the different colors of the stars and locate many pretty double and multiple stars. You can also monitor variable stars from night to night to see how their brightness changes over time. To view a star, press the Star button on the controller. The LCD screen will then display the word “STAR” with the word “NAMED” flashing next to it. From this screen, use the arrow buttons to choose from “NAMED,” “DOUBLE,” “VARIABLE,” and “CATALOG.” Named Stars The named stars are the brightest in the night sky. These are the stars that the ancients gave proper names to, like “Arcturus” or “Mizar.” To select a named star, press Enter after selecting “NAMED” from the Star button choices. You can now use the arrow buttons to scroll through the list of named stars. The stars are listed in alphabetical order. Once you have found the named star you would like to observe, the guide arrows will direct you to move the telescope to the star’s position. The upper left corner of the LCD screen will show the named star’s ST catalog number (the IntelliScope’s entire ST catalog is printed in Appendix D for easy reference), and the lower left shows the constellation in which the star resides. Pressing Enter again will display the star’s R.A. and Dec. coordinates, its magnitude, and a brief description. To find another named star to observe, simply continue scrolling through the list of named stars. Double (and Multiple) Stars Many stars in the night sky appear to be single stars, but they are not. They are actually double or multiple star systems. Some of these systems comprise two or more stars gravitationally bound to each other, while others are just two (or more) stars in the same line of sight. At high magnifications, it is possible to “split” many double (and multiple) stars into their individual components. It can also be interesting to contrast and compare the different colors and magnitudes of the stars in the system. Be aware, however, that good seeing conditions are critical for separating close components of a double or multiple star. To select a double (or multiple) star to observe, press Enter after selecting “DOUBLE” from the Star button choices. The LCD screen will then display the word “DOUBLE” with a flashing three- letter constellation designation after it. Now, select the constellation in which you would like to view a double star. Use the arrow buttons to scroll through the list of constellations. If you are unsure which constellation the three-letter designation represents, refer to Appendix C. Once you have selected the constellation, press Enter. A double star in that constellation will now appear on the LCD screen, along with the guide arrows to lead you to the double star. The current constellation is shown in the lower left, and the double star’s name is in the lower right. Note: Double stars typically have names like “Zeta” (Greek letter designation) or a number like “36” (Flamsteed number). The full names for these double stars are actually linked to the constellation they reside in. For example, in the constellation Andromeda, these stars would be “Zeta And” and “36 And.” For more information about the double star selected, press the Enter button. (The “S=” now refers to the separation, in arc-seconds, between the double stars. For multiple stars, 16 the “S=” refers to the separation between the two brightest stars. The “M=” now refers to the magnitude of the brightest star.) To go to the next double star in the selected constellation, simply press the up arrow button. The guide arrows will now direct you to the next double star in the constellation. If there are no more double stars available in that constellation, a double star from the next constellation (in alphabetical order) will be displayed. To select another constellation in which to view a double star, press the Star button, select “DOUBLE”, and press Enter. Variable Stars Variable stars are stars that change their brightness, also called magnitude, over time. The period of brightness change varies greatly from star to star; some variable stars change brightness over several days while others may take several months to noticeably change. It is fun and challenging to watch a star’s magnitude change over time. Observers typically compare the current brightness of the variable star to other stars around it (whose magnitudes are known and do not change over time). To select a variable star to observe, press Enter after selecting “VARIABLE” from the Star button choices. The LCD screen will then display the word “VARIABLE” with a flashing three-letter constellation designation after it. Now, select the constellation in which you would like to view a variable star. Use the arrow buttons to scroll through the list of constellations. If you are unsure which constellation the three-letter designation represents, refer to Appendix C. Once you have selected the constellation, press Enter. A variable star in that constellation will now appear on the LCD screen, along with the guide arrows to lead you to the variable star. The current constellation is shown in the lower left, and the variable star’s name is in the lower right. Note: Variable stars typically have names like “Eta” (Greek letter designation) or a letter designation like “R.” The full names for these variable stars are actually linked to the constellation they reside in. For example, in the constellation Aquila, these stars would be “Eta Aql” and “R Aql.” For more information about the variable star selected, press the Enter button. (The “M=” refers to the mean magnitude of the variable star.) To go to the next variable star in the selected constellation, simply press the up arrow button. The guide arrows will now direct you to the next variable star in the constellation. If there are no more variable stars available in that constellation, a variable star from the next constellation (in alphabetical order) will be displayed. To select another constellation in which to view a variable star, press the Star button, select “VARIABLE,” and press Enter. Catalog (ST) Stars The “ST” catalog contains all of the stars in the IntelliScope Computerized Object Locator’s database. This catalog has 837 of the most interesting stars to view in the night sky. The full list of stars appearing in the ST catalog is printed Appendix D. Generally, the best way to use the ST catalog to observe stars is first to peruse Appendix D, and then note the catalog number of the star you wish to observe. To select an ST catalog star to observe, press Enter after selecting “CATALOG” from the Star button choices. The LCD screen will then display the letter “ST” with three digits blinking after it. Now, input the ST catalog number of the star you wish to observe, and press Enter. If the ST catalog number of the star you wish to view contains three digits, it is not necessary to press Enter after inputting the third digit. 17 The object’s ST catalog designation will be shown in the upper left corner of the LCD screen, with the guide arrows in the upper right. The lower left will show the constellation the object resides in and the star’s name. You can get more information on the star selected by pressing the Enter button. The second line of the LCD screen will then cycle information about the object you are viewing, such as its celestial coordinates (R.A. and Dec.), magnitude (brightness), and a brief description. When you are finished viewing the selected star, you may scroll to another star in the ST catalog by using the arrow buttons, or you can select another ST catalog star to view by pressing the Star button, and pressing Enter once “CATALOG” is selected. 8. Tours of the Best Objects The IntelliScope controller offers guided tours of the best and brightest celestial objects visible in the sky each month. There are 12 monthly tours, each consisting of 12 preselected objects. The tours are an easy and fun way to locate and observe the finest wonders of the heavens. They are a great place to start for a beginner who is unfamiliar with the night sky, or for a more experienced observer who wants to revisit some old favorites or show friends or family “what’s up” on a given evening. Starting a Tour To start an IntelliScope tour, press the Tour button at any time after you have aligned the IntelliScope system. The LCD screen will display “SKY TOUR” and a flashing three-letter designation for the month. Scroll through the months by using the arrow buttons until you reach the present month, then press the Enter button. The LCD screen will then display the first tour object for the selected month in the lower right of the screen, with the guide arrows in the upper right. Use the guide arrows to point the telescope, and you will soon be observing the first astronomical showpiece of the month. You can get more information about the current tour object by pressing the Enter button. The second line of the LCD screen will then cycle the following information about the object you are viewing: its celestial co-ordinates (R.A. and Dec.), magnitude (brightness), size (in arc minutes or seconds), and a brief text description. When you have finished viewing the first tour object for the selected month, you can continue the tour by pressing the up arrow button to find the next object. You can exit the tour at any time by pressing any one of the other function buttons on the controller. Since several months’ tour objects are visible in the night sky at one time, feel free to select a month before or after the current month. These tour objects will likely be visible also. Remember, however, that viewing objects below 40˚ or so from the horizon will not give the best view due to atmospheric distortion (and usually light pollution). If you are finding that objects in the selected tour month are too close to the horizon, you should choose a month following the selected month, or you can wait a few hours for the objects to rise higher in the sky! 9. The Identify Function There may come a time in your observations when you spot an unidentified deep-sky object or star in the eyepiece and want to know what it is. With the IntelliScope Computerized Object Locator, a simple press of a button will tell you. 18 Using the ID Button When you locate an object and center it in the eyepiece, you can identify it by simply pressing the ID button. The LCD screen will display “IDENTIFY” with the word “ANY” flashing. You can then use the up/and down arrow buttons to scroll through several more specific options (“STAR”, “DOUBLE”, “CLUSTER”, “NEBULA”, and “GALAXY”). If you know which one of these object types you are looking at, selecting the object type will make the identification quicker and more accurate. This is because the computer will search through a shorter list of potential object matches, and will allow proper identification if there are several objects within the same field of view. If you are unsure of the object type you are looking at, simply select “ANY” from the list of choices. Once you have selected the object type (or “ANY”), press the Enter button. The identity of the object centered in the eyepiece will now be displayed in the lower right area of the LCD screen. The constellation in which the object resides is shown in the lower left. As always, to get more information about the object, press the Enter button. An interesting feature of the ID function is that once initiated, it is continually active. So, if you press the ID button, and choose “STAR”, for instance, you can move your telescope from star to star in the sky, and the controller will automatically display the star’s identity when you center the star in the eyepiece. This can be a fun and easy way to identify the stars in the sky. In fact, you can even make a “Name That Star” game out of it! Point your finger at a bright star in the sky and see if you can name it. Then, just point the telescope at the star to see if you were correct or not. If the centered star is not in the controller’s database, it will display the identity of the closest star that is in its database. To exit the identify function, simply press any other of the controller’s function buttons. If you would like to identify another object type, press the ID button again. 10. Adding User-Defined Objects Not only does the IntelliScope’s database contain over 14,000 fascinating objects to view, you can even add your own! Up to 99 user-defined objects can be entered into the database by means of the User button. These user-defined objects can be random stars, a faint object not contained in the controller’s database, or just a pretty object that you would like to come back to at some point in the future. To enter a user-defined object into the database, you must have the right ascension (R.A.) and declination (Dec.) coordinates for the object. If you are currently observing an object that is not in the controller’s database and you wish to add it, but don’t know its coordinates, you can use the FCN button to obtain its coordinates (described in next section). To input a user-defined object, begin by pressing the User button. The LCD screen will display the word “NEW” with a two-digit number flashing after it. Since no user-defined objects currently exist, press Enter to create user-defined (“NEW”) object number 01. The LCD will display the R.A. and Dec. coordinates for the “NEW” object selected in the lower left. Since no data has been input yet, these coordinates will be 00:00 +00.0. The first four digits indicate the R.A. coordinate (in R.A. hours and minutes), and the remaining digits (and the ± sign) indicate the Dec. coordinate (in degrees). Now, press the Enter button, and the first two digits of the R.A. coordinate (R.A. hours) will begin flashing. Press the two numerical buttons on the keypad that correspond the hours value of the R.A. coordinate. If the value of the R.A. hours is less than 10, make sure to enter a zero first. Then the second two digits of the R.A. coordinate (R.A. minutes) will begin flashing. Press the two numerical buttons that correspond to the minutes value of the R.A. coordinate. If the R.A. minutes are less than 10, make sure to enter a zero first. Next, the sign 19 of the Dec. coordinate will be flashing. Use the arrow buttons to select “+” or “-”for the Dec. coordinate. Then, the first two digits of the Dec. coordinate will begin flashing. Press the two numerical buttons that correspond to the degrees value of the Dec. coordinate. Then the tenth of a degree value for the Dec coordinate will begin flashing. Press the numerical button that corresponds to the tenths of a degree value for the Dec. coordinate. You have now input the data for your first user-defined object. Remember that this object is now “NEW01”. If you wish to view this object in the future, press the User button, and press Enter once “NEW01” is selected. The guide arrows will then tell you where to point your telescope to find the user-defined object. If you wish to input another user-defined object, select “NEW02” (by using numerical buttons or the arrow buttons) after pressing the User button and input the data as outlined previously. If you select a “NEW” object number that you have already entered coordinates for and attempt to input new data, you will lose the data that was input previously. You may find it convenient to keep a written log of the “NEW” objects so that you can easily keep track of them. 11. The FCN Button The IntelliScope Computerized Object Locator has several other useful functions, a couple of which can be accessed by using the FCN (function) button. R.A. and Dec. Coordinates By simply pressing the FCN button, the controller will give a continuous readout of the telescope’s current R.A. and Dec. coordinates. This can be helpful and powerful in a number of ways. You can easily find any object in the night sky if you know its right ascension and declination coordinates. Grab any star atlas, choose any object you wish to view, be it faint galaxy or random star, and jot down its coordinates. Then, once you have aligned the IntelliScope system, you can point the telescope to that location by simply pressing the FCN button and moving the telescope until the R.A. and Dec. coordinates displayed match the coordinates of the object you wish to view. You can also press the FCN button at any time to display the current R.A. and Dec. coordinates of whatever you are currently viewing. A common use for the FCN button is to locate “transient” objects, such as comets and asteroids. To find these objects you will need to learn their coordinates from astronomy resources, such as Astronomy, Sky & Telescope or a reliable astronomy website. Comet and asteroid positions will change from night to night, so entering the current coordinates into the user-defined database is generally not useful. After pressing the FCN button, the R.A. and Dec. coordinates corresponding to the center of the telescope’s field of view are displayed on the first line of the LCD screen. The lower left of the screen indicates the current constellation the telescope is pointing to. The lower right numbers are the current azimuth (“AZ”) and altitude (“ALT”) coordinates of the telescope; this information is generally not useful. The Realignment Function This function is useful for obtaining a new alignment fix during an observing session to correct for small pointing errors. Use this function only when pointing accuracy for a certain area of the sky appears to be poor compared to other areas of the sky. This is evident when objects in one area of the sky consistently fall at the edge or just outside the field of view (of the 25mm eyepiece) when the numbers on the LCD screen read 0.0 0.0. 20 This can happen if the alignment stars initially chosen during setup are somewhat close to each other (less than 60˚ apart) or if the area of sky being viewed is a considerable distance away from the alignment stars chosen. To improve pointing accuracy in a specific area of the sky, select an object in the locator’s database from that region, and use the guide arrows to find the object. Precisely center the object in the eyepiece (preferably a high-powered one). Now, press the FCN button, and the R.A. and Dec. coordinates of the centered object will be displayed. Then, press the Enter button. The LCD screen will now display “ALIGN OBJECT 3” on the first line, and will be flashing the object currently centered in the telescope on the second line. Pressing Enter again then realigns the IntelliScope system to the object centered in the telescope. The LCD screen will display a new “warp factor” associated with the new alignment. If this number is greater than ±0.5, you may want to consider resetting the controller to perform another two-star alignment. Turn the controller off, then on again (with the Power button), to do this. If, instead of pressing Enter a second time after pressing the FCN button, you press one of the arrow buttons, the list of initial setup alignment stars will be displayed. If you wish, you can select one of these alignment stars to realign on. Do this by scrolling to the desired alignment star using the arrow buttons, center the star in the telescope, and press Enter. In general, it will not be necessary to use the realignment function, but it is a handy feature to have at your disposal. Also, be aware that while pointing accuracy will increase in the area of sky around the object realigned on, it may decrease in other areas of the sky. 12. The “Hidden” Functions All of the active functions of the IntelliScope Computerized Object Locator have been outlined. There are, however, some additional “hidden” functions that may be of some use to you. To access the hidden functions, press the Enter button while pressing the Power button to turn the controller on. The LCD will display its introduction screen (with software version number) and then show the words “ALT AZM TEST.” This is the first hidden function. Scroll to the other hidden functions by using the arrow buttons. The other hidden functions are “ENCODER TEST,” “DOWNLOAD,” “CHECKSUM,” “REWRITE,” and “CLOCK.” When the hidden function you wish to use is displayed, press Enter to select it. To exit the currently chosen hidden function, press any button except for the Enter or arrow buttons. To completely exit the hidden functions section of the controller, you will need to hold the Power button down until the controller turns off. The rest of this section gives the details and purpose of each hidden function. Altitude and Azimuth Test The altitude and azimuth test (“ALT AZM TEST”) is a diagnostic test that gives relative altitude and azimuth positions for the telescope. This test will allow you to easily see if the encoders are “talking” to the controller, and if the encoders are accurately monitoring the telescope’s motions. To effectively use this test, make sure the telescope optical tube is in the horizontal position when pressing the Enter and Power buttons to access the hidden functions. Once “ALT AZM TEST” is chosen from the hidden function options, the LCD screen will display the telescope’s current relative altitude and azimuth position (in degrees); the relative altitude is in the upper right, while the relative azimuth is in the lower right. To begin 21 with, both of these numbers will be +000.0. The first two sets of numbers on the upper and lower lines of the LCD screen are meaningless for the purposes of this test. If you move the telescope counter-clockwise in azimuth, the number in the lower right should increase, while if you move clockwise in azimuth, the number will decrease. If you rotate the telescope exactly 360˚ in azimuth, the readout should return to the original +000.0 reading. If you move the telescope upwards in altitude, the number in the upper right should increase, while if you move downwards in altitude, the number will decrease. If the telescope tube was perfectly horizontal when you enabled the hidden functions of the controller, then the altitude will read +090.0 when the telescope is pointed precisely vertical. If one, or both, of the encoders are not behaving properly when performing this diagnostic test, there may be a problem with the assembly of the system, or a problem with one of the encoder boards or discs. Also, be sure to check that all cable connections are secure. Encoder Test The encoder test is another diagnostic test that gives information about the performance of the encoders themselves. Select “ENCODER TEST” from the list of hidden functions using the arrow buttons and press Enter. The LCD screen will now display two lines of data. The top line of data corresponds to the altitude encoder, while the lower line of data corresponds to the azimuth encoder. The first two digits on each line denote the amplitude of the signal from one of the magnetic sensors on the encoder board, the second two digits represent the amplitude from the other sensor on the encoder board. The numbers are in hexadecimal (base 16) digits. Therefore “A” in hexadecimal represents “11” in decimal, “B” represents “12” in decimal, “C” represents “13,” “D” represents “14,” “E” represents “15,” and “F” represents “16.” When moving the telescope in altitude or azimuth, you will note that each of the digit pairs rises and falls. None of the digit pairs should ever go above “F3.” If they do, then the encoder disk is too close to the sensors on the encoder board. This will generally not happen in altitude, but can happen in azimuth. If you notice that the first or second digit pair on the second line of the display goes above “F3,” then try loosening the lock nut on the azimuth nut of the base by about 1/16 turn. If this does not work, you will need to disassemble the azimuth encoder (azimuth encoder disk, brass bushing, and azimuth encoder board) and reassemble it carefully according to the instructions that came with the IntelliScope Dobsonian telescope itself. If you notice that the two digit pairs on the first line are going above “F3,” then there is a problem with your altitude encoder assembly. More than likely, the altitude encoder disk is bent. The three-digit number displayed after the digit pairs on each line is the “radius” for each encoder. This number should not go above about 125 or below about 30. If it does, performance may be compromised for the corresponding encoder. If the number goes above 125, then the encoder disk and magnet may be too close to each other. If the number goes below 30, then the encoder disk and magnet may be too far away from each other. Also, if the radius varies by more than 30 counts in a cycle, encoder performance may not be optimal, and you should contact Orion’s Customer Service Department. The four-digit number at the end of each line is the raw encoder “ticks” in hexadecimal numbers. This information will generally not be useful for diagnostic testing of the encoders. 22 Download This function allows downloading of software changes and upgrades available from Orion’s website. To use this option, you must have the optional IntelliScope-to-PC cable, available from Orion. Check www.telescope.com for more information about available software downloads for the IntelliScope Computerized Object Locator. Checksum The checksum function is used to make sure that software has loaded into the controller properly. It has no purpose until a new software version is downloaded. Check the IntelliScope download section on www.telescope.com to see what the proper checksum should be for each new software version. Rewrite Rewrite is also only used after a new software version has been downloaded. It rewrites the new software into its memory in order to prevent any potential problems from arising after the software transfer. Clock This function allows use of the IntelliScope system with equatorial platforms for Dobsonian telescopes. If you are using your IntelliScope with a Dobsonian equatorial platform, press Enter when the selection “CLOCK” is displayed from the available “hidden” function choices. The LCD screen will then show the word “ON” blinking. For normal operation of the IntelliScope system, the controller’s internal clock should be on. For use with a Dobsonian equatorial platform, use the up or down arrow button to change “ON” to “OFF,” and press Enter. The controller is now ready to be used with a Dobsonian equatorial platform. Now, when you press Power to turn the controller on, the LCD screen will state “CLOCK IS OFF” on the second line of its introduction screen. To turn the controller’s internal clock back on, access the hidden functions, select “CLOCK,” press Enter, change the “OFF” back to “ON,” and press Enter again. 13. Specifications Objects in database: • 110 Messier objects • 7840 New General Catalog objects • 5386 Index Catalog objects • 8 Major planets • 99 User-defined objects Computer interface: RS-232 port Power: Requires one 9V battery This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device nay not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes of modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. 23 Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will no occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an output on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. • A shielded cable must be used when connecting a peripheral to the serial ports. Appendix A: Troubleshooting the IntelliScope System This section is intended to help you if you are encountering any problems with your IntelliScope system. If this information is not useful to you in determining the source of the problem, contact Orion Technical Support via phone or email. Azimuth encoder, in general 1. Is the azimuth axis screw’s hex lock nut tight enough? Is it too tight? Remember, it should be tightened 3/16 to 1/4 turn past when the fender washer is no longer loose under the nut. 2. Does the brass bushing extend slightly above the top surface of the top baseplate? If not, the bushing or top baseplate may need replacement, or there may be an assembly problem. 3. Is the azimuth encoder disk (magnet) bent? If so, you will need to flatten it by bending. 4. Is the azimuth encoder board trimmed flush on the side in contact with the top baseplate? If not, the board will not seat flat against the baseplate and this may cause the encoder’s sensors to come too close to the encoder disk. 5. Is the brass bushing properly registered with the azimuth encoder disk? The feature on the front of the bushing needs to seat into the hole in the disk. Altitude encoder, in general 6. Is the altitude encoder disk significantly bent? If so, the altitude encoder assembly will need replacement. Also, if the altitude encoder mounting screws are loose, there is an increased chance of the user bending the altitude encoder disk. 24 Warp factor consistently above ±0.5 but below ±2.0 7. Check accuracy of vertical stop. Use a carpenter’s level to do this. 8. Are alignment stars being centered with reasonable precision? A high-power eyepiece (at least 10mm focal length), or an illuminated reticle eyepiece (preferred) is recommended. 9. Check encoders as outlined previously. 10. Try to use alignment stars that are well above the horizon. Light from stars is refracted as it travels through the atmosphere and starlight near the horizon has to travel through the greatest amount of atmosphere before reaching your telescope. Stars near the horizon can appear as much as 2° away from their actual position. 11. Avoid long delays between aligning on the first and second alignment stars. The stars in the night sky appear to move due to the rotation of the Earth. If you take more than a few minutes to align on the second star, this stellar motion will result in an increase in the warp factor (and decrease the resultant pointing accuracy). This is because the controller does not yet have a frame of reference to tell which way the stars should appear to be moving before the second star is aligned on. Warp numbers larger than 2.0 12. Are the stars you aligned on actually the stars you select-ed on the controller? Consult the finder charts in Appendix A if you are unsure. 13. The encoder sensors may be coming into contact with the encoder disks. Check both the altitude and azimuth encoders as outlined above. Altitude readouts do not change when you move the scope (during “ALT AZM TEST”) 14. Check the altitude cable’s connections. 15. Make sure the knob that goes through the altitude encoder is tight. Azimuth readouts do not change when you move the scope (during “ALT AZM TEST”) 16. Check the azimuth cable’s connections. 17. Make sure the hex lock nut on the azimuth axis screw is tight. The fender washer underneath the hex lock nut should not be able to move. Remember, the hex lock nut should be tightened about 3/16 to 1/4 turn beyond the point where the washer cannot move any longer. 18. Try disassembling then reassembling the azimuth encoder by disassembling the top and bottom groundboards of the base. If you need to contact Orion Technical Support, email [email protected] or call (800) 676-1343. 25 Appendix B: Alignment Star Finder Charts NORTH b ne De CASSI irf a O P EIA G CY C EPH k NU S EUS M EU S a Capell PE RS Ve ga CA ME LO Polaris PAR DAL IS Dip Little p er DR O AC INI C A NI MIN O S R Pr oc yo n ER NC Spic SC OR U PI CO ER OS rd ha Alp S HY CRATER DR A RVU S PU HYD PP I S S LI BR A a TAN OC SEX ON RG O M VI Siriu s Re gu lus O CA LE WEST AM URS EO MI NO R O RION ar Miz CANES VE N ATI CI B O Ö T ES Arcturus SERPENS CAPUT Denebola L Betelgeuse r OR AJ GEM X LYN ippe COR B O R ONA E A LI S ES OPHIUCHUS C a s t or Big D ne Pointers Key sto HER CUL U TAUR S U RSA MINOR LY RA Rasalhague EAST COMA BERENICES RA ANT CEN TAU RU LIA PY XIS IL W S O RI TI N 20 00 VELA SOUTH SPRING Early March Late March Early April Late April Early May Late May Early June *Daylight saving time 26 1:00 AM 12:00 AM 12:00 AM* 11:00 PM* 10:00 PM* 9:00 PM* 8:00 PM (dusk)* NORTH PERS LYN X EUS Mir fak AN CAMELOPARDALIS OM DR LE O M IN OR A JO Polaris CEP Pointers LEO r pe Dip Little Dip per RT A ACO eb as eg fP DR Den o re ua Sq WEST B O ÖTES S O L S Sp ica S VIRG VU A ITT LE S EN RP UT SE AP C Rasalhague AQ UI C BOORONA REA LIS ne ysto Ke A SAG US INU air Alt PH ULE DEL E QU HERCU LA Arcturus Vega R LY Albireo C Y GNUS P E G ASUS RIU AQUA CU COMA B E R E NIC E S us PISCES Denebola IO SS LA CE Big CA US tz ar Miz HE her a IA U RSA M IN OR PE Alp S NE I CA ATIC VEN A ED R U RS MA PI SC ES t ea Gr EAST PE LA OPHIUCHUS IC PR CA SC UTU M OR SERPENS CAUDA NU S s Antare M IC RO S CO PIU M SA GIT TA LIB RA Tea p ot RIU S S PU LU CO AUS RONA TRAL IS SCO RPIUS IL W O RI TI N 20 00 TELESCOPIUM SOUTH SUMMER Early June Late June Early July Late July Early August Late August Early September 2:00 AM* 1:00 AM* 12:00 AM* 11:00 PM* 10:00 PM* 9:00 PM* 8:00 PM (dusk)* *Daylight saving time 27 NORTH URSA MAJOR Big Di pper M iza ters Poin r N LY DR AC O Little Dipp X er U RSA MIN OR CAM ELO L DA IS pe S PAR Ca Polaris GE M INI CU e lhagu Rosa HER S SERPEN S CAUDA SAG AQ UIL A TUM US LE UU EQ SCU SU GA DE S LPH IN U S E PE ir M PI Great Square of Pegasus ES Alta RO ITTA WEST NUS HU OPHIUC EIA CYG A LYR IOP L AC E RTA V U L P E CULA C ASS AND A RIES TRIA N G U L U M SEUS eo Albir P Deneb a Veg CE HEU S Mirfak PER Algo l Hyades TAURUS SC LE Keystone lla Aldebaran N IDA ER IU S US CE TU S US AQUARIUS O IC PR CA haut Fomal SCULP FO RN AX TOR US PISCIS A PHO T RIN US E NIX S RO MIC CO IL W PI SA GI TT AR ORION Betelgeu se EAST Alpheratz DA RN UM O RI TI N 20 00 S GRU SOUTH AUTUMN Early September Late September Early October Late October Early November Late November Early December *Daylight saving time 28 2:00 AM* 1:00 AM* 12:00 AM* 11:00 PM* 9:00 PM 8:00 PM 7:00 PM NORTH CYGN U S HER C CU LE S EPH EUS BO CO DRA CE RT A S Mi za r Big tz ME LOP ARDALIS r pe Dip he ra CA Alp PIS CES ULU ol Alg T RIA N G n ION u se Betelge CET C IN M AN XT US OR Mira I d TA UR US n yo oc I Pr AN O SE S H ph MO ar d Rig NO CER OS el I ER Sirius AN PY TL XIS US FO LEP C A NIS MAJOR RN A X RA US Al YD DA N TER CRA s ulu Reg M IN S Hya des eb a ra x ER LEO CANC Pollu r WEST X Casto PERSEUS N LY LE O MIN OR A RIES ak rf Mi M OR Denebola la pel Ca Gre at of Pe ga su s ES UR SA MA J C BER OMA ENIC ES VIRGO EAST Al GE R Sq ua re CA SIO ÖT er Dipp U RSA MINOR Polaris P EI A AN PE OM DR GA SU A ED S LA Little C VE AN NA ES TIC I ers int Po Adhara IA COLU VEL A PUPPIS MBA CA EL UM IL W O RI TI N 20 00 SOUTH WINTER Early December Late December Early January Late January Early February Late February Early March 2:00 AM 1:00 AM 12:00 AM 11:00 PM 10:00 PM 9:00 PM 8:00 PM 29 Appendix C: Constellation Abbreviations And Andromeda CVn Canes Venatici Ori Ant Antlia Cyg Cygnus Pav Pavo Aps Apus Del Delphinus Peg Pegasus Aql Aquila Dor Dorado Per Perseus Aqr Aquarius Dra Draco Phe Phoenix Ara Ara Equ Equuleus Pic Pictor Ari Eri PsA Piscis Austrinus Aries Eridanus Orion Aur Auriga For Fornax Psc Pisces Boo Boötes Gem Gemini Pup Puppis Cae Caelum Gru Grus Pyx Pyxis Cam Camelopardalis Her Hercules Ret Reticulum Cap Capricorn Hor Horologium Scl Sculptor Car Carina Hya Hydra Sco Scorpius Cas Cassiopeia Hyi Hydrus Sct Scutum Cen Centaurus Ind Indus Ser Serpens Cep Cepheus Lac Lacerta Sex Sextans Cet Cetus Leo Leo Sge Sagitta Cha Chamaeleon Lep Lepus Sgr Sagittarius Cir Lib Libra Tau Taurus Cnc Cancer LMi Leo Minor Tel CMa Canis Major Lup Lupus CMi Canis Minor Lyn Lynx TrA Triangulm Australe Col Columba Lyr Lyra Tri Com Coma Berenices Men Mensa Tuc Tucana CrA Corona Australis Mic Microscopium UMa Ursa Major Mon Monoceros UMi Ursa Minor CrB Corona Borealis Mus Musca Vel Vela Crt Nor Norma Vir Cru Crux Oct Octans Vol Volans Crv Corvus Oph Ophiuchus Vul Vulpecula 30 Circinus Crater Telescopium Triangulum Virgo 31 Name Name O∑∑254 30 ∑3053 SU Ced214 ∑3062 Alpheratz ∑2 Kappa Algenib AD 7 ∑12 S ∑13 ST Groombridge34 ∑24 Iota VX R ∑30 AQ Beta ∑36 Zeta Delta 55 Schedar O∑18 HN122 Delta Eta 65 Do13 Lambda1 36 Navi ∑80 ∑79 U ∑88 ∑90 Zeta Eta Lux Lydiae Mirach Zeta Kappa Number Number ST001 ST002 ST003 ST004 ST005 ST006 ST007 ST008 ST009 ST010 ST011 ST012 ST013 ST014 ST015 ST016 ST017 ST018 ST019 ST020 ST021 ST022 ST023 ST024 ST025 ST026 ST027 ST028 ST029 ST030 ST031 ST032 ST033 ST034 ST035 ST036 ST037 ST038 ST039 ST040 ST041 ST042 ST043 ST044 ST045 ST046 ST047 ST048 ST049 SAO 181 Beta ADS 996 h3423 74 77 Rumker 2 Dunlop 2 ADS 755 “Gamma, Tsih” ADS 683 Alpha ADS 588 ADS 624 Lacaille 119 ADS 449 17 ADS 246 “35, UU” ADS 61 Alpha ADS 102 ß 391 Gamma ADS 180 Other Other RA 00 01.2 00 02.0 00 02.6 00 04.6 00 04.7 00 06.3 00 08.4 00 09.3 00 09.4 00 13.2 00 14.5 00 14.6 00 15.0 00 15.4 00 16.2 00 17.6 00 18.1 00 18.5 00 19.4 00 19.9 00 24.0 00 27.2 00 27.6 00 31.5 00 32.4 00 37.0 00 39.3 00 39.9 00 40.5 00 42.4 00 45.7 00 48.7 00 49.1 00 49.9 00 50.0 00 52.4 00 55.0 00 56.7 00 59.4 01 00.1 01 02.3 01 05.6 01 05.8 01 08.4 01 08.6 01 08.7 01 09.7 01 13.7 01 15.8 RA Dec +60 21 -06.0 +66 06 +43.5 +67.2 +58.4 +29 05 +79.7 -28 00 +15.2 -07.8 -18.9 +08 49 -32.1 +76.9 +50.3 +44.0 +26 08 -08.8 +44.7 +38 35 +49 59 +35.6 -63.0 +06.9 +53.9 +30.9 +21 26 +56.5 +04.2 +75.0 +07.6 +57 49 +27.7 +64.1 -69.5 +23.6 +60.7 +00 47 +44 43 +81 51 +21 28 +04 55 -55.3 -10.2 +86.3 +35.6 +07.6 -68.9 Dec Mag 7.6 4.4 5.9 8 7.8 6.4 2.1 6.6 6.2 2.8 4.9 4.4 5.8 5.5 7 9 8 7.6 3.5 8 5.8 6.9 6.9 4.4 5.7 3.7 3.3 5.4 2.2 7.8 5.7 4.4 3.4 6.3 11 6.5 6 2.5 8.4 6 6.8 5.3 6.8 3.9 3.5 4.3 2 5.6 5.1 Mag Sep 59" * 15" * 30' 1.5" * 0.8" 2" * 1.5° * 12" * 0.9" * 39" 5" * * Stellar 15" * 27" 28" * * 6" * 1.5" 36" * 12" 4.4" 13’ 21" 0.8" * 26" 8" Stellar 30" 33" 6.4" * * * 23" 5.4" Sep Con Cas Psc Cas And Cep Cas And Cep Scl Peg Cet Cet Psc Scl Cep Cas And And Cet And And Cas And Tuc Psc Cas And Psc Cas Psc Cas Psc Cas Psc Cas Tuc And Cas Cet And Cep Psc Psc Phe Cet Cep And Psc Tuc Con Code 5 1 5 1 130 4 21 4 4 21 1 1 5 22 4 1 2 2 21 21 22 2 1 2 2 21 21 5 21 4 2 21 5 5 120 2 4 21 3 3 22 3 2 2 21 21 21 2 2 Code Appendix D: ST Catalog colored double star red variable star colored double star red variable star emission nebula double star challenge star double star challenge double star challenge star red variable star red variable star colored double star variable star double star challenge red variable star double star double star star star variable star double star red variable star double star double star star star colored double star star double star challenge double star star colored double star colored double star scattered group of stars double star double star challenge star double star equal magnitude double star equal magnitude variable star double star equal magnitude double star double star star star star double star double star 32 Name Z ∑113 Psi R Gamma Achernar 51 UV p Nu 44 Phi ∑162 ∑174 ∑163 Baten Kaitos ∑178 ∑180 Psi Epsilon ∑186 56 Lambda Upsilon ∑202 Almach Hamal 59 Iota ∑231 ∑228 ∑232 ∑239 Mira Iota ∑268 ∑274 Polaris Omega 30 R ∑299 ∑305 RZ pi ∑307 R ∑330 Acamar ∑333 Epsilon ∑331 Menkar Rho ∑320 Number ST050 ST051 ST052 ST053 ST054 ST055 ST056 ST057 ST058 ST059 ST060 ST061 ST062 ST063 ST064 ST065 ST066 ST067 ST068 ST069 ST070 ST071 ST072 ST073 ST074 ST075 ST076 ST077 ST078 ST079 ST080 ST081 ST082 ST083 ST084 ST085 ST086 ST087 ST088 ST089 ST090 ST091 ST092 ST093 ST094 ST095 ST096 ST097 ST098 ST099 ST100 ST101 ST102 ST103 ST104 Alpha 25 ADS 2237 Theta Epsilon Eta R TRI Gamma Alpha h 3506 Omicron ADS 1697 66 ADS 1709 Alpha Gamma Alpha 45 ADS 1538 ADS 1534 ADS 1563 Gamma Zeta 1 Dunlop 5 106 Burnham 1103 Alpha 42 ADS 1129 Other 16.2 19.8 25.9 27.0 28.4 37.7 38.0 38.8 39.8 41.4 43.3 43.7 49.3 50.1 51.3 51.5 52.0 53.5 53.6 54.4 55.9 56.2 57.9 00.0 02.0 03.9 07.2 10.9 12.4 12.8 14.0 14.7 17.4 19.3 29.1 29.4 31.5 31.8 33.9 37.0 37.0 43.3 47.5 48.9 49.3 50.7 53.9 57.2 58.3 59.2 59.2 00.8 02.3 05.2 06.2 RA 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 02 02 02 02 02 02 02 02 02 02 02 02 02 02 02 02 02 02 02 02 02 02 02 02 02 02 02 02 03 03 03 03 Dec +25.8 -00 31 +68.1 -32.5 -43.3 -57 14 +48.6 -18.0 -56.2 +05.5 +60.6 +50.7 +47 54 +22.3 +64 51 -10.3 +10 48 +19.3 -46.3 +63.7 +01.9 +37.3 +23.6 -21.1 +02.8 +42.3 +23.5 +39 02 +30.3 -02.4 +47.5 +30 24 +28 44 -03.0 +67.4 +55 31 +01 05 +89 16 -28 13 +24 38 +34.3 +03.2 +19 22 +69 38 +17 28 +55 53 -49.9 -00.6 -40.3 +29.3 +21 20 +52 20 +04.1 +38.8 +79 24 Mag 8.8 6.4 4.7 6.1 3.4 0.5 3.6 7 5.8 4.4 5.8 4.1 5.8 6 6.6 3.7 8.5 4.5 4.4 3.4 6.8 5.7 4.8 4 4 2.2 2 5.6 5 5.7 6.6 8 7 2 4 6.9 7.3 2 5 6.5 5.4 3.6 7.4 6.2 5.2 3.9 4.7 7.3 3.5 4.6 4.6 5.4 2.5 3.4 5.8 Sep * 1.6" 25" * 4’ * * * 11.5" * 1.6" * 2" 2.6" 35" 3’ 3" 8" 5° * 1" 3' 37" * 1.6" 10" * 16" 3.8" 16.5" 1.1" 7" 14" * 2.2" 3" 14" 18" 11" 39" * 2.7" 3" Stellar 3" 28" * 9" 8" 1.4" 1" 12" * * 5" Con Psc Cet Cas Scl Phe Eri And Cet Eri Psc Cas Per Per Ari Cas Cet Ari Ari Phe Cas Cet And Ari Cet Psc And Ari And Tri Cet And Tri Tri Cet Cas Per Cet UMi For Ari Tri Cet Ari Cas Ari Per Hor Cet Eri Ari Ari Per Cet Per Cep Code 21 4 9 22 21 21 21 22 2 21 2 21 8 2 5 2 3 3 1 21 4 2 2 21 4 5 21 5 5 2 4 3 2 22 6 2 3 2 2 5 22 2 4 22 6 9 22 2 2 4 4 2 21 1 5 star double star challenge double star magnitude contrast variable star star star star variable star double star star double star star triple star challenge double star colored double star double star double star equal magnitude double star equal magnitude red variable star star double star challenge double star double star star double star challenge colored double star star colored double star colored double star double star double star challenge double star equal magnitude double star variable star triple star double star double star equal magnitude double star double star colored double star variable star double star double star challenge variable star triple star double star magnitude contrast variable star double star double star double star challenge double star challenge double star star red variable star colored double star 33 Name h3568 Algol Alpha h3556 ∑362 ∑369 ADS2446 Zeta Tau4 Toms Topaz Mirfak Y ∑394 ∑385 ∑389 Sigma ∑401 Epsilon ∑400 O∑36 U1 Omicron Pi Gamma ∑52 F BE Atik 32 Epsilon Zaurak Lambda O∑531 ∑485 Omicron2 Epsilon Theta Phi T ∑528 ADS3169 43 ß 184 ∑552 1 ∑559 46 Aldebaran Nu 53 ∑572 54 R ∑590 Iota Number ST105 ST106 ST107 ST108 ST109 ST110 ST111 ST112 ST113 ST114 ST115 ST116 ST117 ST118 ST119 ST120 ST121 ST122 ST123 ST124 ST125 ST126 ST127 ST128 ST129 ST130 ST131 ST132 ST133 ST134 ST135 ST136 ST137 ST138 ST139 ST140 ST141 ST142 ST143 ST144 ST145 ST146 ST147 ST148 ST149 ST150 ST151 ST152 ST153 ST154 ST155 ST156 ST157 ST158 ST159 55 Dunlop 18 ADS 3305 Alpha 48 Upsilon3 Chi Rumker 3 ADS 3137 Gamma 35 ADS 2995 SZ 40 30 ∆ 16 SAO 12916 Zeta ADS 2850 ADS 2726 26 ADS 2612 ADS 2650 ADS 2544 ADS 2472 SAO 75871 Alpha Beta ADS 2402 Other 07.5 08.2 12.1 12.4 16.3 17.2 17.7 18.2 19.5 20.3 24.3 27.7 28.0 29.1 30.1 30.6 31.3 32.9 35.0 40.0 41.6 44.3 46.1 47.2 48.3 48.6 49.5 54.1 54.3 57.9 58.0 00.7 07.6 07.8 15.2 16.5 17.7 20.4 22.0 22.6 22.7 24.0 27.9 31.4 32.0 33.5 33.9 35.9 36.3 38.2 38.5 40.4 40.5 43.6 50.9 RA 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 04 Dec -79.0 +41.0 -29.0 -44.4 +60 02 +40 29 +38.6 -62.5 -21.8 +29.0 +49 52 +44.2 +20 27 +59.9 +59 21 +48.0 +27 34 -09.5 +60.0 +63.9 +62.6 +32.3 -12.1 -74.2 +11.2 -37 37 +65.5 +31.9 -03.0 +40 01 -13.5 +12.5 +38.1 +62 20 -07.7 -59.3 -63.3 +27.4 +19 32 +25.6 +15.1 -34.0 -21 30 +40 01 +53 55 +18 01 -06.7 +16.5 -03.4 -14.3 +26 56 -19.7 -38.2 -08 48 -53.5 Mag 5.6 2.2 4 6 8.5 6.7 7.8 5.2 3.7 4.5 1.8 8.1 7.1 4.2 6.5 4.4 6.4 3.7 6.8 6.8 8.1 3.8 4.4 3.2 5 4.9 4.5 2.9 5 2.9 3 3.3 7.4 7 4.5 4.4 6.2 5 8.4 5.5 7.3 4 7.3 7 5.4 6.9 5.7 0.9 3.9 3.9 7.3 4.3 6.7 6.7 5.6 Sep * * 9" 8" * * 7" 9" * * 1.4" 90" 83" * 4" 52" Stellar 19.4" 1.4" * 1.7" 9" 10" 3" 4’ 30" 11° * 4" * * 9" 12" 15" * 5" 3.5" 7" 3" 0.9" 5" * 9° * * 7" 2.4" 2.7" * 11" * 1.4" 46" Con Hyi Per For Eri Cam Per Per Ret Eri Ari Per Per Ari Cam Cam Per Tau Eri Cam Cam Cam Per Eri Hyi Tau Eri Cam Per Eri Per Eri Tau Per Cam Eri Ret Ret Tau Tau Tau Tau Eri Eri Per Cam Tau Eri Tau Eri Eri Tau Eri Cae Eri Pic Code 2 22 2 2 3 5 4 2 21 21 21 22 2 2 2 21 3 21 2 2 22 21 1 21 2 3 21 21 5 9 21 22 4 2 8 21 2 2 22 2 4 1 4 3 5 3 2 5 21 21 3 1 22 3 2 double star variable star double star double star double star equal magnitude colored double star double star challenge double star star star star variable star double star double star double star star double star equal magnitude star double star double star variable star star red variable star star double star double star equal magnitude star star colored double star double star magnitude contrast star variable star double star challenge double star triple star challenge star double star double star variable star double star double star challenge red variable star double star challenge double star equal magnitude colored double star double star equal magnitude double star colored double star star star double star equal magnitude red variable star variable star double star equal magnitude double star 34 Name ST Pi4 TT Pi5 Omicron2 Iota Pi6 Omega Hinds Crimson Star ∑627 ∑631 ∑630 Epsilon Zeta W Epsilon Eta O∑98 TX SY ∑644 ∑655 Rho Rigel ∑653 Capella S 476 h3750 UV ADS3954 ∑696 ∑701 Eta Sigma Theta Bellatrix ∑698 ∑716 ∑725 TL9 Delta 119 ∑718 RT ∑747 Lambda Trapezium ∑752 Alnilam Phi2 Zeta Sigma Phact Alnitak U2 Number ST160 ST161 ST162 ST163 ST164 ST165 ST166 ST167 ST168 ST169 ST170 ST171 ST172 ST173 ST174 ST175 ST176 ST177 ST178 ST179 ST180 ST181 ST182 ST183 ST184 ST185 ST186 ST187 ST188 ST189 ST190 ST191 ST192 ST193 ST194 ST195 ST196 ST197 ST198 ST199 ST200 ST201 ST202 ST203 ST204 ST205 ST206 ST207 ST208 ST209 ST210 ST211 ST212 ST213 ST214 Other Alpha Zeta 123 Iota Epsilon ADS 4182 ADS 3984 Dunlop 20 Gamma ADS 4000 118 31 KBC Group ADS 4134 CE ADS 3954 ADS 3962 ADS 3978 Beta ORI 14 Alpha Iota 10 14 8 ADS 3606 ADS 3623 10 ADS 3572 R 8 9 RV 3 51.2 51.2 51.6 54.2 56.4 57.0 58.5 59.3 59.6 00.6 00.7 02.0 02.0 02.5 05.4 05.5 06.5 07.9 09.1 09.8 10.4 12.3 13.3 14.5 15.4 16.7 19.3 20.5 21.8 21.8 22.8 23.3 24.5 24.7 24.8 25.1 25.2 29.3 29.7 30.0 32.0 32.2 32.4 33.2 35.0 35.1 35.3 35.4 36.2 36.9 37.6 38.7 39.6 40.8 42.2 RA 04 04 04 04 04 04 04 04 04 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 05 Dec +68 10 +05.6 +28.5 +02.4 +13.5 +33.2 +01.7 +37.9 -14.8 +03 36 -13.5 +01.6 +43 49 +41.1 +01.2 -22.4 +41.2 +08 29 +39.0 -05.6 +37 17 -11.9 +02 52 -08.2 +32.7 +46 00 -18 30 -21 14 +32.5 -24.8 +03.6 -08.4 -02 24 +37.4 -52.3 +06.3 +34.9 +25 09 -01.1 +17.0 -00.3 +18.6 +49 24 +07.2 -06.0 +09 56 -05 23 -05 55 -01.2 +09.3 +21.1 -02 36 -34.1 -01.9 +62.5 Mag 9.2 3.7 8 3.7 4.1 2.7 4.5 5 5.9 6.6 7.5 6.5 2.9 3.8 8.6 3.2 3.2 5.9 8.5 9 6.8 4.5 4.5 0 5.1 0.1 6.2 4.7 7.4 5.5 5 6 3.4 5 6.8 1.6 6.6 5.8 4.7 5 2.2 4.7 7.5 8 4.8 3.4 5.1 2.9 1.7 4 3 3.7 2.6 2 7.7 Sep Stellar * * * * * * 5.4" * 21" 5.5" 15" Stellar * * * * 0.7" * * 2" 13" 7" 9.4" 11" * 39" 4" * 3.2" 32" 6" 1.5" 9" 38" * 31" 5" * 5° 53" * 8" * 36" 4" 13" 11" * * * 11" * 2.4" * Con Cam Ori Tau Ori Ori Aur Ori Aur Lep Ori Lep Ori Aur Aur Ori Lep Aur Ori Aur Eri Aur Lep Ori Ori Aur Aur Lep Lep Aur Lep Ori Ori Ori Aur Pic Ori Aur Tau Ori Tau Ori Tau Aur Ori Ori Ori Ori Ori Ori Ori Tau Ori Col Ori Cam Code 1 21 22 21 21 21 21 2 22 3 2 2 22 21 22 21 21 4 22 22 4 2 5 9 6 21 3 9 22 2 2 2 4 2 2 21 2 2 21 0 2 21 3 22 2 9 7 9 21 21 21 7 21 9 22 red variable star star variable star star star star star double star variable star double star equal magnitude double star double star variable star star variable star star star double star challenge variable star variable star double star challenge double star colored double star double star magnitude contrast triple star star double star equal magnitude double star magnitude contrast variable star double star double star double star double star challenge double star double star star double star double star star asterism double star star double star equal magnitude variable star double star double star magnitude contrast quadruple star double star magnitude contrast star star star quadruple star star double star magnitude contrast variable star 35 Name Gamma Y Mu Saiph ∑795 Beta Delta Nu ∑817 Betelgeuse U Theta Pi ∆23 ∑855 TU ∑845 SS Gamma Propus ∑872 KS Zeta V Mirzam Mu 8 Canopus BL 15 Beta ADS5150 ∑924 ADS5188 CR ∑928 ADS5201 ∑929 ∑939 ADS5221 Nu1 UU ADS5240 ADS5245 South529 Innes5 ADS5265 Innes1156 SAO172106 ∑953 VW Sirius ∑948 ∑958 Kappa Number ST215 ST216 ST217 ST218 ST219 ST220 ST221 ST222 ST223 ST224 ST225 ST226 ST227 ST228 ST229 ST230 ST231 ST232 ST233 ST234 ST235 ST236 ST237 ST238 ST239 ST240 ST241 ST242 ST243 ST244 ST245 ST246 ST247 ST248 ST249 ST250 ST251 ST252 ST253 ST254 ST255 ST256 ST257 ST258 ST259 ST260 ST261 ST262 ST263 ST264 ST265 ST266 ST267 ST268 ST269 Other 13 Alpha 12 ADS 5311 ADS 5208 ADS 5191 20 Alpha BL Beta Furud Eta ADS 4849 41 Alpha SAO 196149 Kappa 52 Wazn ADS 4334 44.5 45.7 46.0 47.8 48.0 51.0 51.3 51.5 54.9 55.2 55.8 59.7 59.9 04.8 09.0 10.9 11.7 13.4 14.9 14.9 15.6 19.7 20.3 22.7 22.7 23.0 23.8 24.0 25.5 27.8 28.8 31.8 32.3 34.3 34.4 34.7 35.1 35.4 35.9 36.2 36.4 36.5 36.9 37.3 37.6 38.0 38.4 39.1 39.5 41.2 42.2 45.1 46.2 48.2 49.8 RA 05 05 05 05 05 05 05 05 05 05 05 05 05 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 Dec -22.5 +20.7 -32.3 -09.7 +06 27 -35.8 -20.9 +39.1 +07 02 +07 24 +20.2 +37 13 +45.9 -48 27 +02 30 +26.0 +48 42 +47.0 -06.3 +22.5 +36.2 -05.3 -30.1 -02.2 -18.0 +22.5 +04 36 -52 42 +14.7 +20 47 -07 02 +38.9 +17.8 +38.1 +16.1 +38.4 +37.1 +37.7 +05.3 +38.0 -18.7 +38.5 +38.2 +38.4 +12.2 -61.5 +38.8 -29.1 -30.0 +08 59 +31.5 -16.7 +59 27 +55 42 -32.5 Mag 3.7 7.1 5.2 2 6.1 3.1 3.8 4 8.8 0.5 5.3 2.6 4.3 7 6 7.5 6.1 10 4 3.3 6.9 9.5 3 6 2 2.9 4.3 -0.7 8.5 6.6 3.8 11.5 6.3 6.7 8.5 7.6 7.4 7.4 8.3 8.5 6 5.1 9.7 8.8 7.6 6.4 9.6 8 7.8 7.1 8.7 -1 4.9 5.5 4 Sep 97" * * * “1.3" * * 30" 19" Stellar * 3.5" 1° 2.7" 30" * 8" * 8° * 11" * 8.5° * * * 13" * * 27" 3" 4.5" 20" 43" * 3.5" 2.6" 6" 30" 1.3" 17.5" * 2.2" 10" 70" 2.4" 4.6" 0.7" 2.5° 7" * 9" 2" 5" * Con Lep Tau Col Ori Ori Col Lep Aur Ori Ori Ori Aur Aur Pup Ori Gem Aur Aur Mon Gem Aur Mon Cma Mon Cma Gem Mon Car Ori Gem Mon Aur Gem Aur Gem Aur Aur Aur Mon Aur Cma Aur Aur Aur Gem Pic Aur Cma Cma Mon Gem Cma Lyn Lyn Cma Code 2 22 21 21 4 21 21 21 3 21 22 9 1 3 2 22 2 22 21 21 2 22 21 22 21 21 5 21 22 2 6 2 5 2 22 2 2 2 2 4 5 22 2 2 2 2 2 4 1 2 22 9 8 3 21 double star variable star star star double star challenge star star star double star equal magnitude star variable star double star magnitude contrast red variable star double star equal magnitude double star variable star double star variable star star star double star variable star star variable star star star colored double star star variable star double star triple star double star colored double star double star variable star double star double star double star double star double star challenge colored double star variable star double star double star double star double star double star double star challenge red variable star double star variable star double star magnitude contrast triple star challenge double star equal magnitude star 36 ST270 ST271 ST272 ST273 ST274 ST275 ST276 ST277 ST278 ST279 ST280 ST281 ST282 ST283 ST284 ST285 ST286 ST287 ST288 ST289 ST290 ST291 ST292 ST293 ST294 ST295 ST296 ST297 ST298 ST299 ST300 ST301 ST302 ST303 ST304 ST305 ST306 ST307 ST308 ST309 ST310 ST311 ST312 ST313 ST314 ST315 ST316 ST317 ST318 ST319 ST320 ST321 ST322 ST323 ST324 Rumker 8 17 Rumker 7 Dunlop 65 Zeta V Alpha Kappa 2 ADS 6117 “HN19, h269” Alpha 69 h 3948 55 19 4 ADS 5871 28 RV Dunlop 42 ADS 5846 Zeta 21 22 24 Mu 16 14 Other 14 Name ∑963 GY ∑987 Omicron1 Theta 38 ∑997 BG O∑80 RV Epsilon Sigma Omicron2 Dunlop38 Mekbuda ∑1009 R W Gamma Tau ∑1035 ∑1037 Omega h3945 Tau Delta ∑1062 Gamma Sigma ∑1093 n Castor Upsilon ∑1121 K Procyon O∑179 ∑1138 ∑1127 ∑1149 U Chi Dunlop59 S-h86 Naos RT RU Epsilon Gamma Zeta c Beta R Kappa AC Number 53.1 53.2 54.1 54.1 54.2 54.6 56.1 56.4 58.1 58.4 58.6 01.7 03.0 04.0 04.1 05.7 07.4 08.1 08.8 11.1 12.0 12.8 14.8 16.6 18.7 20.1 22.9 28.2 29.2 30.3 34.3 34.6 35.9 36.6 38.8 39.3 44.4 45.5 47.0 49.4 55.1 56.8 59.2 02.5 03.6 05.4 07.5 07.9 09.5 12.2 15.3 16.5 16.6 19.8 22.7 RA 06 06 06 06 06 06 06 06 06 06 06 07 07 07 07 07 07 07 07 07 07 07 07 07 07 07 07 07 07 07 07 07 07 07 07 07 07 07 07 07 07 07 07 08 08 08 08 08 08 08 08 08 08 08 08 Dec +59.5 -04.6 -05 51 -24.2 -12.0 +13 11 -14 02 +07.1 +14.2 +06.2 -29.0 -27.9 -23.8 -43.6 +20.6 +52 45 +22.7 -11 55 -70.5 +30.2 +22 17 +27.2 -26.8 -23 19 -24 57 +21 59 +55 17 +08.9 -43.3 +50.0 -23 28 +31.9 +26.9 -14 29 -26 48 +05 14 +24 23 -14 41 +64 03 +03 13 +22 00 -53.0 -50.0 +63.1 -40.0 -38.8 -22.9 -68.6 -47.3 +17 39 -62.9 +09.2 +11.7 -71.5 -15.9 Mag 5.7 9.4 7.1 3.9 4.1 4.7 5.3 9.2 7.3 7 1.5 3.5 3 5.6 3.7 6.9 6 6.4 4 4.4 8.2 7.2 3.9 4.5 4.4 3.5 5.6 4.3 3.3 8.8 5.1 2 4.1 7.9 3.8 0.4 3.7 6.1 7 7.9 8.2 3.5 6.5 6 2.3 8.5 8.9 4.4 1.9 4.7 5.3 3.5 6.1 5.4 8.9 Sep 0.4" * 1.3" * * 7" 2.8" * 2’ * 7.5" * * 20.5" * 4.1" * Stellar 13.6" 1.9" 4" 1.3" * 27" 15" 6" 15" * 22" 0.8" 10" 1.8" 2.5° 7" 10" Stellar 7" 17" 5" 22" Stellar 4° 16" 49" 4° * * 6" 41" 0.6" 4" * * 65" * Con Lyn Mon Mon Cma Cma Gem Cma Mon Gem Mon Cma Cma Cma Pup Gem Lyn Gem CMa Vol Gem Gem Gem Cma CMa CMa Gem Lyn Cmi Pup Lyn Pup Gem Gem Pup Pup CMi Gem Pup Cam Cmi Gem Car Pup Cam Pup Pup Pup Vol Vel Cnc Car Cnc Cnc Vol Pup Code 4 22 4 21 21 5 9 22 0 22 2 21 21 2 22 3 22 1 2 2 3 4 21 5 6 9 6 21 2 4 3 4 1 3 3 21 9 3 6 2 22 21 2 2 21 22 22 2 2 8 2 21 22 2 22 double star challenge variable star double star challenge star star colored double star double star magnitude contrast variable star asterism variable star double star star star double star variable star double star equal magnitude variable star red variable star double star double star double star equal magnitude double star challenge star colored double star triple star double star magnitude contrast triple star star double star double star challenge double star equal magnitude double star challenge red variable star double star equal magnitude double star equal magnitude star double star magnitude contrast double star equal magnitude triple star double star variable star star double star double star star variable star variable star double star double star triple star challenge double star star variable star double star variable star 37 Name 31 Beta h4903 ∑1224 ∑1223 h4104 ∆70 h4107 ∑1245 Sigma h4128 ∑1254 Alpha Delta ∑1270 ∑1268 Epsilon ∑1282 X ∑1298 Rho ∑1311 Suhail Sigma2 a h4188 h4191 ∑1321 g RT ∑1334 ∑1338 Alpha Kappa ∑1347 Kappa ∑1355 Alphard ∑1356 Dunlop76 ∑1360 Zeta N ∑1351 Alterf R ∑1369 Iota Upsilon R W Y Rasalas h4262 Regulus Number ST325 ST326 ST327 ST328 ST329 ST330 ST331 ST332 ST333 ST334 ST335 ST336 ST337 ST338 ST339 ST340 ST341 ST342 ST343 ST344 ST345 ST346 ST347 ST348 ST349 ST350 ST351 ST352 ST353 ST354 ST355 ST356 ST357 ST358 ST359 ST360 ST361 ST362 ST363 ST364 ST365 ST366 ST367 ST368 ST369 ST370 ST371 ST372 ST373 ST374 ST375 ST376 ST377 ST378 ST379 Mu ADS 7571 Alpha Rumker 11 RV ADS 7438 23 Lambda Alpha Omega ADS 7351 40 38 Lambda 66 Innes 10 ADS 6977 Iota 5 HYA 24 Phi Other 22.8 25.7 26.3 26.7 26.7 29.1 29.5 31.4 35.8 38.8 39.2 40.4 43.6 44.7 45.3 46.7 46.8 50.8 55.4 01.4 02.5 07.5 08.0 10.4 11.0 12.5 14.4 14.9 16.2 18.4 18.8 21.0 21.1 22.1 23.3 24.7 27.3 27.6 28.5 28.6 30.6 30.8 31.2 31.5 31.7 32.2 35.4 39.9 47.1 47.6 51.0 51.1 52.8 54.5 08.4 RA 08 08 08 08 08 08 08 08 08 08 08 08 08 08 08 08 08 08 08 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 09 10 Dec +43.2 -66.1 -39.1 +24 32 +26 56 -47.9 -44 44 -39 04 +06 37 +03.3 -60.3 +19 40 -33.2 -54.7 -02.6 +28 46 +06 25 +35 03 +17.2 +32 15 +67.6 +22 59 -43 26 +67 08 -59.0 -43.6 -43 13 +52 42 -57.5 +51.4 +36 48 +38 11 +34.4 -55.0 +03 30 +26.2 +06 14 -08 40 +09.1 -45.5 +10 35 -31 53 -57.0 +63 03 +23.0 -62.8 +40.0 -01.1 -65.1 +11 26 -02.0 -23.0 +26.0 -12.9 +11 58 Mag 4.3 3.8 6.5 7.1 6.3 5.5 5 6.4 6 4.4 6.9 6.4 3.7 2.1 6.4 4 3.4 7.5 5.6 5.9 4.8 6.9 2.2 4.8 3.4 6.7 5.2 8.1 4.3 8.6 3.9 6.6 3.1 2.5 7.2 4.5 7.5 2 5.9 7.8 8.3 5.8 3.1 3.8 4.3 3.8 6.5 3.9 3.1 4.4 9 8.3 3.9 8.7 1.4 Sep 15° 6° 8" 6" 5" 3.6" 5" 4" 10" * 1.4" 21" * 2.6" 5" 30" 3" 4" * 5" 1° 8" Stellar 4" 50’ 2.7’ 6" 18" 5’ * 3" 1" * * 21" 2.1" 2.3" Stellar 0.5" 61" 14" 8" * 23" * * 25" * 5" Stellar * * * 8" Stellar Con Lyn Vol Pup Cnc Cnc Vel Vel Vel Cnc Hya Car Cnc Pyx Vel Hya Cnc Hyd Lyn Cnc Cnc Uma Cnc Vel Uma Car Vel Vel Uma Car Uma Lyn Lyn Lyn Vel Hya Leo Hya Hya Leo Vel Leo Ant Vel Uma Leo Car Lyn Hya Car Leo Sex Hya Leo Hya Leo Code 21 21 2 2 3 2 2 6 2 21 4 7 21 2 2 5 9 3 22 2 21 3 21 9 21 2 9 3 21 22 4 4 21 21 2 6 3 21 4 2 3 2 21 9 21 22 2 21 2 1 22 22 21 2 21 star star double star double star double star equal magnitude double star double star triple star double star star double star challenge quadruple star star double star double star colored double star double star magnitude contrast double star equal magnitude variable star double star star double star equal magnitude star double star magnitude contrast star double star double star magnitude contrast double star equal magnitude star variable star double star challenge double star challenge star star double star triple star double star equal magnitude star double star challenge double star double star equal magnitude double star star double star magnitude contrast star variable star double star star double star red variable star variable star variable star star double star star 38 Name S ADS7704 Adhafera q h4306 Algieba Tania Australis Mu Alpha 45 Delta p Rho 49 U Gamma U Dunlop95 ∑1466 R VY Delta ∑1476 Nu 54 SAO251342 Xi Alula Borealis ∑1529 h4432 Iota ∑1540 Tau Giausar 88 N Innes78 ∑1552 Nu Denebola Beta O∑112 ∑1579 Epsilon ∑1593 Zeta Delta ∑1604 Epsilon Rumker14 Delta 2 Epsilon ∑1627 R Number ST380 ST381 ST382 ST383 ST384 ST385 ST386 ST387 ST388 ST389 ST390 ST391 ST392 ST393 ST394 ST395 ST396 ST397 ST398 ST399 ST400 ST401 ST402 ST403 ST404 ST405 ST406 ST407 ST408 ST409 ST410 ST411 ST412 ST413 ST414 ST415 ST416 ST417 ST418 ST419 ST420 ST421 ST422 ST423 ST424 ST425 ST426 ST427 ST428 ST429 ST430 ST431 ST432 ST433 ST434 ADS 8489 2 65 h4486 Beta ADS 8148 83 84 Lambda x ADS 8119 Nu ADS 7979 40 x 35 47 HN 50 Gamma Mu 42 Zeta Other 09.4 16.3 16.7 17.1 19.1 20.0 22.3 26.1 27.2 27.6 29.6 32.0 32.8 35.0 35.2 35.5 37.6 39.3 43.4 44.6 45.1 45.8 49.3 49.6 55.6 17.5 18.2 18.5 19.4 23.4 23.9 26.8 27.9 31.4 31.8 32.3 33.6 34.7 45.9 49.1 52.9 54.6 55.1 59.6 03.5 04.3 08.4 09.5 10.1 14.0 15.1 16.1 17.6 18.1 19.6 RA 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 11 11 11 11 11 11 11 11 11 11 11 11 11 11 11 11 11 11 11 12 12 12 12 12 12 12 12 12 12 12 Dec -61.6 +17.7 +23.4 -61.3 -64.7 +19.8 +41.5 -16.8 -31.1 +09.8 -30 36 -61.7 +09.3 +08 39 -39.6 -78.6 -13.4 -55.6 +04 44 +68.8 +67.4 -80.5 -04 01 -16.2 +24.8 -63.5 +31.5 +33.1 -01 38 -65.0 +10.5 +03 00 +02.9 +69.3 +14 21 -29 16 -40.6 +16 48 +06.5 +14 34 -33.9 +19.4 +46 29 -78.2 -02 26 +21.5 -50.7 -11 51 -22.6 -45.7 -58.7 +40.7 -68.0 -03 56 -19.3 Mag 4.5 7.2 3.4 3.4 5.6 2.5 3 3.8 4.3 6 5.7 3.3 3.9 5.7 8.1 4.1 7 4.3 6.3 7.5 5.9 4.5 6.9 3.1 4.5 7 4.5 3.5 7 5.1 4 6.2 5.5 3.8 6.4 5.8 6 6 4 2.1 4.7 8.4 6.7 5.4 8.7 6 2.6 6.6 3 5.6 2.8 6 4.1 6.6 6.7 Sep * 1.4" 5.5’ * 2.1" 4.4" * * * 3.8" 11" * * 2" * * * 52" 7" * * 4.5’ 2.5" * 6.8" 7" 1.3" 7" 10" 2.3" 1.3" 29" 1.5’ 20’ 16" 9" 1" 3" * Stellar 0.9" 73" 4" 0.9" 1.3" 3.6" 4.5’ 10" * 2.9" * 11.5" * 20" * Con Car Leo Leo Car Car Leo Uma Hya Ant Leo Ant Car Leo Leo Ant Cha Hya Vel Sex Uma Uma Cha Sex Hya Leo Car Uma Uma Leo Mus Leo Leo Leo Dra Leo Hyd Cen Leo Vir Leo Hya Leo Uma Cha Vir Com Cen Crv Crv Cen Cru Cvn Mus Vir Crv Code 22 4 2 21 2 2 21 21 21 2 9 21 21 4 22 21 22 2 2 22 22 2 2 21 2 9 4 2 2 2 4 6 2 1 2 3 4 6 21 21 5 2 2 5 4 2 2 6 21 2 21 5 1 3 22 variable star double star challenge double star star double star double star star star star double star double star magnitude contrast star star double star challenge variable star star variable star double star double star variable star variable star double star double star star double star double star magnitude contrast double star challenge double star double star double star double star challenge triple star double star red variable star double star double star equal magnitude double star challenge triple star star star colored double star double star double star colored double star double star challenge double star double star triple star star double star star colored double star red variable star double star equal magnitude variable star 39 Name ∑1633 Epsilon M40 17 ∑1639 S SS Acrux 3C273 Algorab Gacrux ∑1649 24 Alpha ADS8612 ∑1669 Gamma Porrima Y Iota Beta Mimosa ∑1694 ∑1687 Mu Delta Cor Caroli RY ∑1699 Delta Theta ∑1724 Alpha 54 J Mizar Spica O∑∑123 R ∑1755 S 25 ∑1763 Epsilon ∑1772 Dunlop141 T Alkaid ∑1785 2 Upsilon 3 Zeta Hadar Pi Number ST435 ST436 ST437 ST438 ST439 ST440 ST441 ST442 ST443 ST444 ST445 ST446 ST447 ST448 ST449 ST450 ST451 ST452 ST453 ST454 ST455 ST456 ST457 ST458 ST459 ST460 ST461 ST462 ST463 ST464 ST465 ST466 ST467 ST468 ST469 ST470 ST471 ST472 ST473 ST474 ST475 ST476 ST477 ST478 ST479 ST480 ST481 ST482 ST483 ST484 ST485 ST486 ST487 ST488 ST489 Beta k Eta ADS 9031 1 ADS 8974 ADS 8972 V ADS 8934 Dunlop 133 Zeta Alpha Rumker 16 “51, Theta” Alpha Beta 32 35 Dunlop 126 h4539 Gamma RV h4547 Delta Gamma ADS 8585 RV Alpha Winnecke 4 ADS 8531 ADS 8539 Other 20.6 21.4 22.4 22.5 24.4 24.6 25.3 26.6 29.1 29.9 31.2 31.6 35.1 37.2 37.7 41.3 41.5 41.7 45.1 45.6 46.3 47.7 49.2 53.3 54.6 55.6 56.0 56.4 58.7 02.3 08.1 09.9 10.0 13.4 22.6 23.9 25.2 27.1 29.7 32.3 33.0 37.5 37.6 39.9 40.7 41.7 41.8 47.5 49.1 49.4 49.5 51.8 55.5 03.8 06.4 RA 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 13 14 14 Dec +27 03 -60.4 +58 05 +05.3 +25.6 -49.4 +00 48 -63.1 +02.0 -16.5 -57.1 -11.1 +18 23 -69.1 -27.1 -13 01 -49.0 -01.4 +45 26 -61.0 -68.1 -59.7 +83 25 +21 14 -57.2 +03.4 +38.3 +66.0 +27 28 -71.5 -65.3 -05 32 +17 32 -18 50 -61.0 +54 56 -11.2 +64 43 -23 17 +36.8 -07.2 +36.3 -07.9 -53.5 +19 57 -54.6 -33.6 +49.3 +27.0 -34.5 +15.8 -33.0 -47.3 -60.4 -26.7 Mag 6.3 3.6 9 6.5 6.8 9.2 6 1 12.8 3 1.6 8 5 2.7 5.5 5.3 2.2 3.5 7.4 4.7 3.7 1.3 5.3 5.1 4.3 3.4 3 6.8 8.8 3.6 5.7 4.4 5 6.8 4.7 2.3 1 6.7 4 7 6 5 7.9 2.3 5.7 5.3 5.5 1.9 7.6 4.2 4.1 4.5 2.6 0.6 3.3 Sep 9" * 50" 21" 1.6" * Stellar 4.4" * 24" 10" 15" 20" * 1.3" 5" 1" 3" Stellar 27 1.4 * 22" 29" 35" * 19" * 1.5" 8’ 5.3" 7" 0.5" 5" 1’ 14" * 69" Stellar 4.4" * 1.8" 2.8" * 5" 5.3" * * 3.4" * * 8" 5° * * Con Com Cru UMa Vir Com Cen Vir Cru Vir Crv Cru Vir CVn Mus Hya Crv Cen Vir CVn Cru Mus Cru Cam Com Cru Vir Cvn Dra Com Mus Mus Vir Com Vir Cen Uma Vir Dra Hyd Cvn Vir Cvn Vir Cen Boo Cen Cen Uma Boo Cen Boo Cen Cen Cen Hya 3 21 2 2 4 22 1 2 0 2 2 2 5 21 4 3 4 2 1 2 4 21 3 9 2 1 2 22 4 21 2 8 4 2 2 2 21 5 22 2 22 9 2 21 9 2 22 21 2 21 21 2 21 21 21 Code double star equal magnitude star double star double star double star challenge variable star red variable star double star asterism double star double star double star colored double star star double star challenge double star equal magnitude double star challenge double star red variable star double star double star challenge star double star equal magnitude double star magnitude contrast double star red variable star double star variable star double star challenge star double star triple star challenge double star challenge double star double star double star star colored double star variable star double star variable star double star magnitude contrast double star star double star magnitude contrast double star variable star star double star star star double star star star star 40 Name Kappa Kappa ∑1819 Arcturus Iota R ∑1834 ∑1833 Dunlop159 ∑1835 SHJ 179 5 Proxima Rho h4690 Rigil Kentaurus Pi ∑1864 Zeta Alpha q Alpha c1 Izar Dunlop 54 Alpha ∑1883 Mu 39 58 Kochab Zubenelgenubi Xi h4715 33 Beta Pi 44 Sigma Dunlop178 Kappa X ∑1932 Mu ∑1931 S Phi1 Eta Mu Edasich ∑1972 Lal123 ∑1954 Gamma Number ST490 ST491 ST492 ST493 ST494 ST495 ST496 ST497 ST498 ST499 ST500 ST501 ST502 ST503 ST504 ST505 ST506 ST507 ST508 ST509 ST510 ST511 ST512 ST513 ST514 ST515 ST516 ST517 ST518 ST519 ST520 ST521 ST522 ST523 ST524 ST525 ST526 ST527 ST528 ST529 ST530 ST531 ST532 ST533 ST534 ST535 ST536 ST537 ST538 ST539 ST540 ST541 ST542 ST543 ST544 Delta Iota Pi h4753 Dunlop 177 H 28 Beta Alpha 37 Epsilon Dunlop 169 H 97 Dunlop 166 Alpha ADS 9338 pi ADS 9296 ADS 9286 ADS 9229 Alpha ADS 9198 Other 12.9 13.5 15.3 15.7 16.2 16.6 20.3 22.6 22.6 23.4 25.5 27.5 29.9 31.8 37.3 39.6 40.7 40.7 41.1 41.9 42.0 42.5 43.7 45.0 45.2 46.0 47.9 48.9 49.3 49.7 50.3 50.7 50.9 51.4 56.5 57.3 58.5 01.8 03.8 04.1 11.6 11.9 14.3 18.3 18.5 18.7 21.4 21.8 23.2 24.5 24.9 29.2 33.1 34.8 35.1 RA 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 Dec -10.3 +51 47 +03 08 +19 11 +51.4 -59.9 +48.5 -07 46 -58.5 +08 26 -19 58 +75.7 -62.7 +30.4 -46 08 -60 50 +16.4 +16 25 +13 44 -47.4 -37.8 -65.0 -35.2 +27 04 -55.6 -25 26 -79.0 +05 57 -14 09 +48 43 -28.0 +74.2 -16.0 +19 06 -47.9 -21 22 -43.1 -83.2 +47 39 -25.3 -45.3 -48.7 -70.1 +26 50 -47.9 +10 26 +31.4 -36.3 +30 17 +37 23 +59.0 +80 26 -24 29 +10.5 -41.2 Mag 4.2 4.4 7.8 0 4.9 5.3 8.1 7.6 5 5.1 6.4 4.3 10.7 3.6 5.4 0 5 4.9 3.8 2.3 4 3.2 4 2.4 6.2 5.2 3.8 7.6 5.4 5.7 4.4 2.1 2.8 4.6 6 5.9 2.6 5.7 4.8 3.2 6.7 3.9 8.1 6.6 5.1 7 5.8 3.6 5.6 4.3 3.3 6.9 7.5 4 2.8 Sep * 13" 0.8" Stellar 39" * 1.3" 6" 9" 6" 35" * * * 19" 20" 5.6" 6" 1" * * 16" 17’ 3" 68" 8" 10° 0.7" 2" 3" * * 4’ 7" 2.4" 23" * 18’ 1.5" * 32" 27" * 1.5" 1.2" 13" * 50’ 1.0" 2" * 31" 9" 3.9" * Con Vir Boo Vir Boo Boo Cen Boo Vir Cen Boo Lib Umi Cen Boo Lup Cen Boo Boo Boo Lup Cen Cir Cen Boo Cir Hya Aps Vir Lib Boo Hya Umi Lib Boo Lup Lib Lup Oct Boo Lib Lup Lup Tra CrB Lup Ser Crb Lup CrB Boo Dra Umi Lib Ser Lup Code 21 5 4 21 2 22 4 3 5 2 2 21 22 21 9 2 2 2 4 21 21 2 21 5 2 2 21 4 4 2 21 21 2 5 2 2 21 2 4 1 2 2 22 4 4 2 22 21 4 6 21 2 3 2 21 star colored double star double star challenge star double star variable star double star challenge double star equal magnitude colored double star double star double star star variable star star double star magnitude contrast double star double star double star double star challenge star star double star star colored double star double star double star star double star challenge double star challenge double star star star double star colored double star double star double star star double star double star challenge red variable star double star double star variable star double star challenge double star challenge double star variable star star double star challenge triple star star double star double star equal magnitude double star star 41 Name h4788 Upsilon Omega ∑1962 Tau ∑1965 ∑1967 Unukalhai R Kappa R Xi Rho Epsilon Pi T Eta Delta Xi Graffias Omega1 Kappa Nu Yed Prior ∑2032 Delta Sigma Rho V Epsilon Iota ∑2052 Antares Lambda R 16 H Zeta SU Zeta Atria Eta Epsilon Mu ∑2118 RR Kappa Zeta Epsilon1 Mu Sabik Rasalgethi Delta Pi 36 Number ST545 ST546 ST547 ST548 ST549 ST550 ST551 ST552 ST553 ST554 ST555 ST556 ST557 ST558 ST559 ST560 ST561 ST562 ST563 ST564 ST565 ST566 ST567 ST568 ST569 ST570 ST571 ST572 ST573 ST574 ST575 ST576 ST577 ST578 ST579 ST580 ST581 ST582 ST583 ST584 ST585 ST586 ST587 ST588 ST589 ST590 ST591 ST592 ST593 ST594 ST595 ST596 ST597 ST598 ST599 Other 67 Eta Alpha 27 20 26 ADS 10157 Alpha 13 h4853 Dunlop 201 ADS 10075 Alpha ADS 10087 H 121 ADS 10049 Delta “17, Sigma” Beta 9 5 13 6 V Rmk 21 7 40 Zeta Gamma Alpha V 35 d ADS 9705 35.9 37.0 38.1 38.7 38.7 39.4 42.7 44.3 48.6 48.7 50.7 56.9 56.9 57.6 58.9 59.5 00.1 00.3 04.4 05.4 06.8 08.1 12.0 14.3 14.7 20.3 21.2 25.6 26.7 27.2 28.0 28.9 29.4 30.9 32.7 36.2 36.4 37.2 40.6 41.3 48.7 49.8 50.2 52.3 56.4 56.6 57.7 58.6 59.6 05.3 10.4 14.6 15.0 15.0 15.3 RA 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 16 17 17 17 17 17 17 Dec -45.0 -28.1 -42.6 -08 47 -29.8 +36.6 +26.3 +06.4 +28 09 +18.1 +15.1 -33 58 -29.2 +26.9 -26.1 +25 55 -38 24 -22.6 -11 22 -19.8 -20.7 +17 03 -19 28 -03.7 +33 52 -78.7 -25 35 -23.5 -12.4 -47.6 -64.1 +18.4 -26.4 +02.0 +66.8 +52 55 -35.3 -10.6 -32.4 +31.6 -69.0 -59.0 -34.3 -38.0 +65.0 -30.6 +09.4 -56.0 -53.2 +54 28 -15.7 +14.4 +24 50 +36.8 -26 36 Mag 4.7 3.6 4.3 5.8 3.7 5 4.2 2.7 5.7 4.1 5.2 5.2 3.9 4.2 2.9 2 3.6 2.3 4.2 2.5 4 5 4 2.7 5.2 4.7 2.9 5.3 7.3 4.8 5.3 7.7 1 4.2 6.7 5.1 4.2 2.6 8 3 1.9 3.8 2.3 3 7.1 5.1 3.2 3.1 4.1 4.9 2.4 3 3.2 3.2 4.3 Sep 2.2" 3" * 12" 2° 6.3" 0.3" * Stellar * * 10" * * * Stellar 15" * 1" * 14’ 28" 1" * 7" * 20" 3.1" * 23" 20" 1.7" 3" 1.4" * 3" * * * 1.4" * * * * 1.4" * 75’ * 40’ 2" 0.6" 4.6" 10" 7° 5" Con Lup Lib Lup Lib Lib Crb Crb Ser CrB Ser Ser Lup Sco Crb Sco CrB Lup Sco Sco Sco Sco Her Sco Oph CrB Aps Sco Oph Oph Nor Tra Her Sco Oph Dra Dra Sco Oph Sco Her Tra Ara Sco Sco Dra Sco Oph Ara Ara Dra Oph Her Her Her Oph Code 2 5 1 3 21 2 4 21 22 1 22 2 21 21 21 22 9 21 8 21 21 5 7 21 2 2 9 2 22 2 2 2 4 4 22 6 21 21 22 5 21 21 21 21 4 22 21 21 21 3 4 3 9 21 3 double star colored double star red variable star double star equal magnitude star double star double star challenge star variable star red variable star variable star double star star star star variable star double star magnitude contrast star triple star challenge star star colored double star quadruple star star double star double star double star magnitude contrast double star variable star double star double star double star double star challenge double star challenge variable star triple star star star variable star colored double star star star star star double star challenge variable star star star star double star equal magnitude double star challenge double star equal magnitude double star magnitude contrast star double star equal magnitude 42 Name 39 Theta ∑2161 Beta Gamma Sigma h4949 ∑2173 Lambda Lesath Alpha Nu Shaula Rasalhague Iota ∑2241 Kappa V Cebalrai ∑2202 SZ SX G Y Grumium Eltanin Barnards Star h5003 ∑2038 95 Tau ∑2276 Theta ∑2280 W Eta Kappa Kaus Media ∑2306 Xi ∑2323 21 Alpha 59 Kaus Borealis SS Delta T ∆222 ∑2348 Alpha O∑359 O∑358 Vega X Number ST600 ST601 ST602 ST603 ST604 ST605 ST606 ST607 ST608 ST609 ST610 ST611 ST612 ST613 ST614 ST615 ST616 ST617 ST618 ST619 ST620 ST621 ST622 ST623 ST624 ST625 ST626 ST627 ST628 ST629 ST630 ST631 ST632 ST633 ST634 ST635 ST636 ST637 ST638 ST639 ST640 ST641 ST642 ST643 ST644 ST645 ST646 ST647 ST648 ST649 ST650 ST651 ST652 ST653 ST654 ADS 11483 Alpha Kappa Lambda Gale 2 39 ADS 11325 1 Delta 100 ADS 11005 70 40-41 Xi Gamma Beta 61 Lambda Alpha 85 Psi 76 Upsilon 49 Dunlop 216 42 “75, Rho” Other 18.0 22.0 23.7 25.3 25.4 26.5 26.9 30.4 30.7 30.8 31.8 32.2 33.6 34.9 39.5 41.9 42.5 43.3 43.5 44.6 45.0 47.5 49.9 52.6 53.5 56.6 57.8 59.1 00.0 01.5 03.1 05.5 06.6 07.8 14.9 17.6 19.9 21.0 22.2 23.2 24.0 25.3 27.0 27.2 28.0 30.4 31.8 32.3 33.4 33.9 35.2 35.5 35.9 36.9 38.3 RA 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 Dec -24 17 -25.0 +37 09 -55.5 -56.4 +04.1 -45.9 -01 04 +26.1 -37.3 -49.9 +55 11 -37.1 +12 34 +46.0 +72 09 -39.0 -57.7 +04.6 +02 34 -18.6 -35.7 -37.0 -06.2 +56.9 +51.5 +04 34 -30 15 +80.0 +21 36 -08.2 +02 30 -50.1 +26 06 +36.7 -36.8 +36.1 -29.8 -15 05 -61.5 +58 48 -20.5 -46.0 +00 12 -25.4 -16.9 -45.9 +37.0 -38 44 +52 18 -08.2 +23 36 +17.0 +38 47 +08.8 Mag 5.2 3.3 4.2 2.9 3.3 4.3 6 6 4.4 2.7 3 4.9 1.6 2.1 3.8 4.9 2.4 5.7 2.8 6.2 9 8.5 3.2 6 3.8 2.2 9.5 5 5.7 4.3 5.2 4 3.7 5.9 7.3 3.1 4.3 2.7 7.9 4.4 4.9 4.9 3.5 5.2 2.8 9 5 7.8 5.9 6 3.9 6.3 6.8 0 5.9 Sep 10" * 4" * * 4° 2.2" 1.1" * * * 62" 35’ * * 30" 2.5° * * 21" * * 2° * * * Stellar 6" 20" 6" 1.8" 1.5" * 14" * * * * 10" * 4" 1.8" 6’ 4" * * 11’ * 21" 26" * 0.7" 1.6" Stellar * Con Oph Oph Her Ara Ara Oph Ara Oph Her Sco Ara Dra Sco Oph Her Dra Sco Pav Oph Oph Sgr Sco Sco Oph Dra Dra Oph Sgr Dra Her Oph Oph Ara Her Lyr Sgr Lyr Sgr Sct Pav Dra Sgr Tel Ser Sgr Sgr Tel Lyr CrA Dra Sct Her Her Lyr Oph Code 5 21 2 21 21 21 2 4 21 21 21 3 21 21 21 2 21 22 21 3 22 22 21 22 21 21 21 5 3 3 4 4 21 3 22 21 21 21 2 21 6 4 21 5 21 22 2 1 3 2 21 4 4 21 22 colored double star star double star star star star double star double star challenge star star star double star equal magnitude star star star double star star variable star star double star equal magnitude variable star variable star star variable star star star star colored double star double star equal magnitude double star equal magnitude double star challenge double star challenge star double star equal magnitude variable star star star star double star star triple star double star challenge star colored double star star variable star double star red variable star double star equal magnitude double star star double star challenge double star challenge star variable star 43 Name HK ∑2398 Double-Double Zeta ∑2375 ∑2379 R Beta S ∑2404 ∑2420 Delta2 O∑525 Nunki 13 ∑2417 ADS11871 ∑2422 UV ∑2426 BrsO14 h5082 V 15 Gamma R ∑2449 ∑2474 ∑2486 O∑178 Tau RY U V1942 UX RR ∑2525 h5114 Alpha Albireo Mu AQ R HN84 54 TT 16 ∑2579 O∑∑191 Tarazed ∑2580 Delta Epsilon ∑2583 Zeta Number ST655 ST656 ST657 ST658 ST659 ST660 ST661 ST662 ST663 ST664 ST665 ST666 ST667 ST668 ST669 ST670 ST671 ST672 ST673 ST674 ST675 ST676 ST677 ST678 ST679 ST680 ST681 ST682 ST683 ST684 ST685 ST686 ST687 ST688 ST689 ST690 ST691 ST692 ST693 ST694 ST695 ST696 ST697 ST698 ST699 ST700 ST701 ST702 ST703 ST704 ST705 ST706 ST707 ST708 ST709 Pi “18, Delta” H V 137 Gamma 17 7 ADS 12767 6 Beta 38 RV V ADS 12447 V 60 RV RV ADS 11869 Sigma R “63, Theta” Omicron ADS 11825 ADS 11726 5 V Epsilon Other 42.8 43.0 44.3 44.8 45.5 46.5 47.5 50.0 50.3 50.8 51.2 54.5 54.9 55.3 55.3 56.3 57.0 57.1 58.6 00.0 01.1 03.1 04.4 05.0 06.4 06.4 06.4 09.1 12.1 15.3 15.5 16.5 18.8 19.2 21.6 25.5 26.6 27.8 28.7 30.7 34.1 34.3 36.8 39.4 40.7 40.9 41.8 45.0 45.9 46.3 46.4 47.4 48.2 48.7 49.0 RA 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 19 Dec +37.0 +59.6 +39 40 +37 36 +05 30 -00 58 -05 42 +33 24 -07.9 +10 59 +59 22 +36.9 +33 58 -26.3 +43.9 +04 11 +32.9 +26.1 +14.4 +12 53 -37 03 -19 14 -05 41 -04 02 -37 00 +08 14 +07 09 +34 35 +49 51 +15.1 +73.4 -33.5 +19 37 -15.9 +76 34 +42 47 +27.3 -54.3 +24.7 +28.0 +07.4 -16.4 +50.2 +16 34 -16.3 +32.6 +50 32 +45 08 +35 01 +10.6 +33 44 +18.5 +70 16 +11.8 +19 09 Mag 9.5 8 4.7 4.4 6.2 5.8 4.5 3.5 6.8 6.9 4.9 4.5 6 2 3.9 4.1 5.4 8 8.6 7.1 6.6 6 6.6 5.4 5 5.5 7.2 6.5 6.6 5.7 4.5 6 6.6 6.4 5.9 7.1 8.1 5.7 4.4 3 4.5 9.1 6.1 6.4 5.4 7.8 6 2.9 6 2.7 5 3.8 3.8 6.1 5 Sep * 13" 2" 44" 2" 13" Stellar 47" 14.3" 4" 35" * 45" * 4" 22" 1" 0.7" * 17" 13" 7" Stellar 38" 3" Stellar 8" 16" 8" 90" * * Stellar * Stellar Stellar 2" 70" * 35" * * * 28" 38" * 39" 2" 39" * 26" * 3" 1.4" 9" Con Lyr Dra Lyr Lyr Ser Aql Sct Lyr Sct Aql Dra Cyg Lyr Sgr Lyr Ser Lyr Lyr Aql Aql Cra Sgr Aql Aql Aql Aql Aql Lyr Cyg Aql Dra Sgr Sge Sgr Dra Lyr Vul Tel Vul Cyg Aql Sgr Cyg Sge Sgr Cyg Cyg Cyg Cyg Aql Cyg Sge Dra Aql Sge Code 22 2 7 2 3 6 22 9 2 2 2 21 5 21 21 2 4 4 22 5 3 6 1 5 3 1 2 2 3 2 21 22 22 22 1 22 2 2 21 5 21 22 22 5 2 22 3 9 5 21 9 21 9 4 2 variable star double star quadruple star double star double star equal magnitude triple star variable star double star magnitude contrast double star double star double star star colored double star star star double star double star challenge double star challenge variable star colored double star double star equal magnitude triple star red variable star colored double star double star equal magnitude red variable star double star double star double star equal magnitude double star star variable star variable star variable star red variable star variable star double star double star star colored double star star variable star variable star colored double star double star variable star double star equal magnitude double star magnitude contrast colored double star star double star magnitude contrast star double star magnitude contrast double star challenge double star 44 Name Chi Altair Eta 57 O∑532 Psi RR RU Gamma BF h1470 X WZ ∑2675 ∑2637 RY FG ∑2644 RS ∑2658 Omicron1 RT Alpha RT P Alpha ∑2671 U Dabih 39 Peacock pi Omicron ∑2716 V Deneb ∑2726 Gamma Lambda 3 S763 4 Omega Epsilon ∑2751 ∑2742 Dunlop236 Lambda 12 Xi ∑2758 24 T Gamma ∑2780 Number ST710 ST711 ST712 ST713 ST714 ST715 ST716 ST717 ST718 ST719 ST720 ST721 ST722 ST723 ST724 ST725 ST726 ST727 ST728 ST729 ST730 ST731 ST732 ST733 ST734 ST735 ST736 ST737 ST738 ST739 ST740 ST741 ST742 ST743 ST744 ST745 ST746 ST747 ST748 ST749 ST750 ST751 ST752 ST753 ST754 ST755 ST756 ST757 ST758 ST759 ST760 ST761 ST762 ST763 ST764 50.6 50.8 52.5 54.6 55.3 55.6 55.9 58.7 58.8 02.4 03.6 05.1 07.6 08.9 09.9 10.4 11.9 12.6 13.4 13.6 13.6 17.1 17.6 17.7 17.8 18.0 18.4 19.6 21.0 23.9 25.6 27.3 29.9 41.0 41.3 41.4 45.7 46.7 47.4 47.7 48.4 51.4 51.8 59.1 02.1 02.2 02.2 02.2 04.1 04.9 06.9 07.1 09.5 10.3 11.8 RA 19 19 19 19 Beta 19 19 19 19 12 19 20 20 20 20 Kappa 20 Theta 20 20 20 20 20 20 “ADS 13554, V 695” 20 20 20 20 20 20 20 20 Beta 20 39 20 Alpha 20 20 SHJ 324 20 49 20 20 Alpha 20 52 20 20 ADS 14296 20 20 20 ADS 14360 20 18 20 1 20 ADS 14575 21 2 21 21 ADS 14556 21 21 62 21 61 21 ADS 14632 21 21 21 ADS 14749 21 Other V Alpha 55 Dec +32 55 +08 52 +01.0 -08 14 +06.4 +52 26 -29.2 -41.9 +19.5 +21.1 +38 19 +20.7 +17.7 +77 43 +20 55 +36.0 +20.3 +00 52 +38.7 +53 07 +46.7 -21.3 -12.5 -39.1 +38 02 -12 32 +55 23 +47.9 -14.8 +32.2 -56.7 -18 13 -18 35 +32 18 +48.2 +45 17 +30.7 +16 07 +36.5 -05.0 -18 11 -05.6 -26.9 +04 18 +56.7 +07 11 -43.0 +07.2 -05 49 +43.9 +38 39 -25.0 +68.5 +10.1 +60.0 Mag 3.3 0.8 3.4 5.7 3.7 4.9 5.4 6 3.5 8.5 7.6 7 7 4.4 6.4 8.5 9.5 6.8 6.5 7.1 3.8 8.9 4.2 6 3 3.8 6 5.9 3.4 4.4 1.9 5.3 6.1 5.5 7.7 1.3 4.2 4.3 4.9 4.4 6.7 6.4 4.1 5.2 6.1 7.4 6 7.4 5.9 3.7 5.2 4.5 5.2 4.7 5.6 Sep Stellar * * 36" 13" 3" * * * * 29" * * 7" 12" * * 3" * 5" * * 44" * Stellar 7" 4" * 3’ * * 3" 19" 3" * * 6" 10" 0.9" * 16" 0.8" * 1" 1.5" 3" 57" 3" 3" * 29" * * 6’ 1.0" Con Cyg Aql Aql Aql Aql Cyg Sgr Sgr Sge Sge Cyg Sge Sge Cep Sge Cyg Sge Aql Cyg Cyg Cyg Cap Cap Sgr Cyg Cap Cyg Cyg Cap Cyg Pav Cap Cap Cyg Cyg Cyg Cyg Del Cyg Aqr Cap Aqr Cap Equ Cep Equ Mic Equ Aqr Cyg Cyg Cap Cep Equ Cep Code 22 21 22 2 2 9 22 22 21 22 5 22 22 9 6 22 35 3 22 2 21 22 21 22 22 7 2 22 2 21 21 9 2 9 22 21 2 2 4 1 2 4 21 8 4 3 2 2 4 21 2 39 22 2 4 variable star star variable star double star double star double star magnitude contrast variable star variable star star variable star colored double star variable star variable star double star magnitude contrast triple star variable star planetary nebula irregular double star equal magnitude variable star double star star variable star star variable star variable star quadruple star double star variable star double star star star double star magnitude contrast double star double star magnitude contrast variable star star double star double star double star challenge red variable star double star double star challenge star triple star challenge double star challenge double star equal magnitude double star double star double star challenge star double star stellar planetary nebula variable star double star double star challenge 45 Name Delta Theta RY Y Beta S ∑2816 V460 SS RV Herschel’s Garnet Star Epsilon Lambda AG ∑2840 ∑2841 RX ∑2873 Eta 29 ∑2863 O∑461 Lambda Al Nair ∑2883 Zeta h1746 41 1 Alpha ∑2894 Pi S 53 Delta Kruger60 Zeta Delta 5 Delta2 ∑2912 Roe47 8 11 Beta Tau1 ∑2947 Tau2 ∑2950 h1823 Lambda Fomalhaut 52 Scheat Dunlop246 Number ST765 ST766 ST767 ST768 ST769 ST770 ST771 ST772 ST773 ST774 ST775 ST776 ST777 ST778 ST779 ST780 ST781 ST782 ST783 ST784 ST785 ST786 ST787 ST788 ST789 ST790 ST791 ST792 ST793 ST794 ST795 ST796 ST797 ST798 ST799 ST800 ST801 ST802 ST803 ST804 ST805 ST806 ST807 ST808 ST809 ST810 ST811 ST812 ST813 ST814 ST815 ST816 ST817 ST818 ST819 73 Alpha ADS 16428 Beta 69 ADS 16291 71 ADS 16317 37 h5334 ADS 15972 ADS 15758 Alpha ß 276 S 802 “17, Xi” ADS 15601 ADS 15431 h5278 Mu RV h5258 Other 14.5 19.9 20.3 24.3 28.7 35.2 39.0 42.0 42.7 43.3 43.5 44.2 50.9 51.0 52.0 54.3 56.4 58.4 00.8 02.5 03.8 03.9 06.1 08.2 10.7 10.9 13.9 14.3 16.0 18.5 18.9 23.1 26.1 26.6 27.3 28.1 28.8 29.2 29.5 29.8 30.0 32.5 35.9 40.5 42.7 47.7 49.0 49.6 51.4 51.8 52.6 57.6 59.2 03.8 07.2 RA 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 21 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 23 23 Dec +10 00 -53.5 -10.8 -69.7 +70 33 +78 37 +57 29 +35.5 +43 35 +38.0 +58 47 +09 52 -82.7 +12.6 +55 47 +19.7 +22.9 +82 51 -28 27 -16 58 +64 38 +59.8 -39.5 -46 58 +70 07 +58.2 +39.7 -21 04 +37.7 -60.3 +37 46 -45.9 -48.4 -16 45 -65.0 +57.7 -00 01 +58 25 +47.7 -43.7 +04.4 +39 46 +39 38 +44.3 -46.9 -14.1 +68.6 -13.6 +61.7 +41 19 -07.6 -29 37 +11.7 +28.1 -50.7 Mag 4.6 4.5 8 8.6 3.3 7.4 5.6 5.6 8.2 7.1 3.4 2.5 5.4 6 5.5 6.4 8 7.1 5.8 7.2 4.3 6.7 4.5 1.7 5.7 3.4 4.5 5.3 4.1 2.9 6.1 5.8 6 6.4 4.5 9.8 4.3 3.8 4.4 4.1 5.8 5.8 6.5 4.5 2.1 5.7 7 4 6.1 7.1 3.7 1.2 6.1 2.4 6.1 Sep 48" 6" * * 13" Stellar 12" * Stellar * Stellar 83" 3" * 18" 22" * 14" 1.9" 4" 8" 11.1" * Stellar 15" * 28" 5" * 5’ 16" 2.7" * 3" 7" 3" 2" 20" 5’ 15’ 1" 43" 22" * * 23" 4.3" 40’ 1.7" 82" * * 0.7" * 9" Equ Ind Aqr Pav Cep Cep Cep Cyg Cyg Cyg Cep Peg Oct Peg Cep Peg Peg Cep Psa Aqr Cep Cep Gru Gru Cep Cep Lac Aqr Lac Tuc Lac Gru Gru Aqr Tuc Cep Aqr Cep Lac Gru Peg Lac Lac Lac Gru Aqr Cep Aqr Cep Lac Aqr PsA Peg Peg Gru Con 9 2 22 22 9 1 6 22 22 22 1 9 2 22 2 2 22 3 2 3 2 2 21 21 2 21 2 5 21 21 5 2 22 3 2 2 4 5 21 1 4 7 6 21 21 2 2 21 2 7 21 21 4 21 2 Code double star magnitude contrast double star variable star variable star double star magnitude contrast red variable star triple star variable star variable star variable star red variable star double star magnitude contrast double star variable star double star double star variable star double star equal magnitude double star double star equal magnitude double star double star star star double star star double star colored double star star star colored double star double star variable star double star equal magnitude double star double star double star challenge colored double star star red variable star double star challenge quadruple star triple star star star double star double star star double star quadruple star star star double star challenge star double star 46 Name ∑2978 Pi Phi Psi3 94 Dunlop249 99 Z Errai Theta R 107 TX ∑3042 Lal192 R Sigma ∑3050 Number ST820 ST821 ST822 ST823 ST824 ST825 ST826 ST827 ST828 ST829 ST830 ST831 ST832 ST833 ST834 ST835 ST836 ST837 19 Gamma Dunlop 251 ADS 16538 90 Other 07.5 07.9 14.3 19.0 19.1 23.9 26.0 33.7 39.3 39.5 43.8 46.0 46.4 51.8 54.4 58.4 59.0 59.5 RA 23 23 23 23 23 23 23 23 23 23 23 23 23 23 23 23 23 23 Dec +32 49 +75.4 -06.0 -09.6 -13 28 -53.8 -20.6 +48 49 +77.6 -46.6 -15 17 -18 41 +03 29 +37 53 -27 03 +51 24 +55 45 +33 43 Mag 6.3 4.6 4.2 5 5.1 6.5 4.4 8 3.2 6.6 5.8 5.3 6.9 7.8 6.9 4.7 4.9 6.6 Sep 8" 1.2" * 1.5" 13" 27" * Stellar * 4" Stellar 7" Stellar 5" 7" Stellar 3" 1.5" Con Peg Cep Aqr Aqr Aqr Gru Aqr And Cep Phe Aqr Aqr Psc And Scl Cas Cas And Code 2 4 1 2 5 2 21 22 21 2 22 3 1 3 2 22 5 4 double star double star challenge red variable star double star colored double star double star star variable star star double star variable star double star equal magnitude red variable star double star equal magnitude double star variable star colored double star double star challenge 47 One-Year Limited Warranty This Orion IntelliScope Computerized Object Locator is warranted against defects in materials or workmanship for a period of one year from the date of purchase. This warranty is for the benefit of the original retail purchaser only. During this warranty period Orion Telescopes & Binoculars will repair or replace, at Orion’s option, any warranted instrument that proves to be defective, provided it is returned postage paid to: Orion Warranty Repair, 89 Hangar Way, Watsonville, CA 95076. If the product is not registered, proof of purchase (such as a copy of the original invoice) is required. This warranty does not apply if, in Orion’s judgment, the instrument has been abused, mishandled, or modified, nor does it apply to normal wear and tear. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state. For further warranty service information, contact: Customer Service Department, Orion Telescopes & Binoculars, P. O. Box 1815, Santa Cruz, CA 95061; (800) 676-1343. Orion Telescopes & Binoculars Post Office Box 1815, Santa Cruz, CA 95061 Customer Support Help Line (800) 676-1343 • Day or Evening