Download Chauvet WELL User guide

Omega II
DMX-255
User Guide
Please read these instructions carefully before use
World-wide Headquarters:
3000 North 29th Ct.
Hollywood, FL 33020
U.S.A.
Tel: +1-954-929-1115 Fax: +1-954-929-5560
www.ChauvetLighting.com
Introduction
Congratulations on the purchase of your new CHAUVET lighting effect. We are confident you will enjoy many trouble
free hours with this unit. To assist with the care and use of the product we have prepared this short guide.
General Instructions
Please read the enclosed instructions carefully as they include important points about safety for usage, installation and
maintenance of this unit.
• Please keep this booklet for future consultation. If you sell this unit to another user, be sure that the new user also receives this
manual so that they have the necessary information about the use and maintenance of the unit,
• Before the initial start-up, please unpack and carefully check all components in case any damage may have occurred during
shipment.
• Locate a suitable location for installation where there is good ventilation. Make certain that the fan or vents are not blocked.
• Protect our enviroment! Please dispose of packacking material properly.
• The electrical work that may be necessary for installation must be done by qualified personnel.
• Always remember to unplug the unit from the main power before any service is done.
Do not open the unit other than to replace the lamp. There are no serviceable parts inside.
• It is very important to ground the yellow / green conductor to earth in order to meet regulations for safety.
• Check the surrounding area and make sure that there are no flammable liquids, water or metal objects that could enter the fixture. If a foreign object enters the unit, immediately disconnect the main power. Also, place the fixture in a well-ventillated spot at
about 15 cm from the walls.
• Do not touch any wires during operation, as high voltage is hazardous.
• In the event of serious operating problems, stop using the unit immediately. Never try to repair the unit yourself. Repairs carried
out by unqualified personnel can lead to damage and will void the warranty. Please contact CHAUVET Technical Assistance.
Always use genuine spare parts.
Main Features
• Voltage: AC Switchable 120V, 60Hz / 230V, 50Hz
• Bulb: ELC3 24V 250W
• Beam Angle: 8.8o
• DMX-512 control, 5 DMX channels
• 11 Indexable Colors plus white
• 14 Indexable Gobos plus open
• Pan: 180o
• Tilt: 84o
• Master / Slave mode
• Sound Activated
Top
• Sound Sensitivity
• Power LED
• DMX Signal LED
• Microphone
• CH-X Jack
• DMX In
• DMX Out
• Power Socket
• Fuse Holder
• 110/220V Selector
Lamp
ELC3 24V 250W (300 Hrs)
• Always switch off the main power supply and never handle the lamp or luminaire
when it is hot.
• Never touch the bulb with bare hands. Oils on your skin may greatly reduce the life
of the bulb.
•Screws
• To insert a new lamp, remove the 4 screws on the side of the lamp cover. Insert
the new lamp into the socket and place into the lamp holder. Replace the 4 screws.
• Always use the type of lamp specified.
DMX Operation
Before connecting this unit to the main power supply for the first time you must first install the lamp. (See 'Replacing Lamps' for
details).
This lighting effect has been designed to function on a main power supply of 120V, 60Hz or 230V, 50Hz and has been fitted with
a suitable power plug.
The Omega II (DMX-255) is a DMX fixture that can be operated with CHAUVET's DMX-6, DMX-40, DMX-50, ShowXpress or
any other universal DMX controller. The unit will also work in stand alone mode sound activated. To operate in DMX mode, you
must link the units together using a premium quality 3-pin DMX cable in the following configuration. 'Out' from the first unit to 'In'
on the second, 'Out' from the second to 'In' on the third and so on.
The Omega II (DMX-255) is a 5 channel DMX fixture. Please consult the controller manual to determine the proper address for
the units.
Example: To set the address at 12
1
2
3
4
5
6
7
8
9
1
2
4
8
16
32
64
128
256
Off
On
Value
1.Set SW 10 to OFF.
2. Count the value of the switches in the on position.
and SW 4 equals 8.
3. Set SW 3 and SW 4 to the ON position. (4 + 8 = 12)
DMX Channels
Channel 1
Gobo
Level
Blackout
0-9
Open
10-19
Gobo 1
20-29
Gobo 2
30-39
Gobo 3
40-49
Gobo 4
50-59
Gobo 5
60-69
Gobo 6
70-79
Gobo 7
80-89
Gobo 8
90-99
Gobo 9
100-109
Gobo 10
110-119
Gobo 11
120-129
Gobo 12
130-139
Gobo 13
140-149
Gobo 14
150-159
Auto
160-250
Rotation
Slow-Fast
Channel 2
Color
Level
White
0-9
Color 1
10-19
Color 2
20-29
Color 3
30-39
Color 4
40-49
Color 5
50-59
Color 6
60-69
Color 7
70-79
Color 8
80-89
Color 9
90-99
Color 10
100-109
Color 11
110-119
Auto
120-255
Rotation
Slow-Fast
Channel 3
Strobe
Level
None
0-45
Gobo/Color
46-115
Strobe
Slow-Fast
Color
116-185
Strobe
Slow-Fast
Gobo
186-255
Strobe
Slow-Fast
Channel 4
Pan
Level
Right
0
Left
255
Channel 5
Tilt
Level
Down
0
Up
255
Sound Active Mode
In the absence of a DMX signal, the Omega II will automatically go into sound activation. The first unit in the system will
become the master and all other units will be slave units. In sound activaation, the dip switch settings are irrelevant. The
Omega II will shut off automatically in a few seconds if no DMX signal or sound is received.
Sound activation may also be accessed via your DMX controller. If channel 1is set between 250-255, the Omega II will
run sound activated.
Pan & Tilt Inversion
The pan and tilt may be inverted by use of dip switch #10. By setting dip switch #10 on for 1 unit and off for another, the
Omega II’s will move in opposite directions. This is a very useful feature in creating an interesting show.
LED DMX Indicator
When a DMX signal is present, the blue LED will pulsate rapidly. In sound activation, the led will pulsate to the beat of
the music.
CH-X Blackout Controller
The CH-X blackout controller may be used whenever the Omega II is run in
sound activation. Simply plug the 1/4” plug into the jack on the top of the unit.
Press the button twice and the OMega II will go into blackout. Press again
twice and the program will resume. The CH-X will not operate when a DMX
signal is present.
Installation / Mounting
This unit has been designed to be hung. It is recommended that, for safety purposes, your lighting effect be properly mounted
using a suitable hanging clamp and safety cable. CHAUVET offers a range of items, which are ideal for safe mounting.
Use in a well-ventilated area without obstruction to the vents or fan.
Replacing Fuses
If the unit does not function at all when connected to the main power supply i.e. does not illuminate after replacing the lamp.
Then it is highly likely that the fuse has blown.
Disconnect from main power supply before attempting to replace either lamps or fuse.
In order to replace the fuse, disconnect from the main power supply first, and then pry up the fuse holder cover to reveal the
fuse. The unit has a label attached which indicates the correct fuse rating and you will also find this listed as part of the specifications for the unit later in this guide. It is most important that replacement fuses are of the correct rating. Failure to use the
correct fuse could damage the lighting effect beyond economic repair.
The fuse should simply be placed inside the holder and the fuse holder replaced. When this is done, connect to the main power
supply to check. If the unit is still not working then please contact CHAUVET for servicing.
Specifications
Voltage:
Fuse:
Lamp:
Weight:
Dimensions:
AC 110V 50/60Hz or 240V 50Hz
110V: 7A 250V
240V: 5A 250V
ELC3 24V 250W
22 lbs / 9.8 kgs
18.75” x 8” x 6” / 476mm x 203 mm x 152 mm