Download Samsung VP-D102 Service manual
Transcript
BDP-S300/S301 RMT-B101A/B101P SERVICE MANUAL US Model Canadian Model Ver. 1.1 2007.07 BDP-S300/S301 AEP Model UK Model E Model Russian Model Australian Model Singapore Model Thai Model BDP-S300 Photo: BDP-S300 SPECIFICATIONS System Laser: Semiconductor laser Outputs (Jack name: Jack type/Output level/ Load impedance) AUDIO OUT L/R: Phono jack/2 Vrms/10 kilohms DIGITAL OUT (OPTICAL): Optical output jack/−18 dBm (wave length 660 nm) DIGITAL OUT (COAXIAL): Phono jack/0.5 Vp-p/75 ohms 5.1CH OUTPUT: Phono jack/2 Vrms/10 kilohms HDMI OUT: HDMI 19-pin standard connector COMPONENT VIDEO OUT(Y, /PB/CB, PR/CR): Phono jack/Y: 1.0 Vp-p/PB/CB, PR/CR: progressive or interlace = 0.7 Vp-p/75 ohms TM VIDEO: Phono jack/1.0 Vp-p/75 ohms S VIDEO: 4-pin mini DIN/Y: 1.0 Vp-p, C: 0.286 Vp-p/75ohms (US, CND) 1.0 Vp-p, C: 0.3 Vp-p (PAL)/Y: 1.0 Vp-p, C: 0.286 Vp-p (NTSC)/75ohms (SP) 1.0 Vp-p, C: 0.3 Vp-p (PAL)/75ohms (Except US, CND, SP) General Power requirements: 120 V AC, 60 Hz (US, CND) 110–240 V AC, 50/60 Hz (E32) 220–240 V AC, 50/60 Hz (Except US, CND, E32) Power consumption: 33 W Dimensions (approx.): 430 × 79 × 375 mm (17 × 3 1/8 × 14 7/8 in.) (width/height/depth) incl. projecting parts Mass (approx.): 4.5 kg (10 lb) Operating temperature: 5 °C to 35 °C (41°F to 95°F) Operating humidity: 25 % to 80 % Supplied accessories • Video cord (phono plug × 1) (1) • Stereo audio cord (phono plug × 2) (1) • HDMI cord (1) (supplied with BDP-S301 only) • Power cord (1) • Remote commander (remote) (1) • Size AA (R6) batteries (2) • Plug Adaptor (1) (E32) • GNU License Information (1) (Except US, CND) Specifications and design are subject to change without notice. • Abbreviation CND : Canadian model E32 : Latin American model SP : Singaporean model BLU-RAY DISC PLAYER SAFETY CHECK-OUT After correcting the original service problem, perform the following safety checks before releasing the set to the customer: LEAKAGE TEST The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microamperes). Leakage current can be measured by any one of three methods. 1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges. 2. Check the interboard wiring to ensure that no wires are “pinched” or contact high-wattage resistors. 3. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement. 1. A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers' instructions to use these instruments. 4. Look for parts which, though functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement. 2. A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. 3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The “limit” indication is 0.75V, so analog meters must have an accurate lowvoltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2V AC range are suitable. (See Fig. A) 5. Check the line cord for cracks and abrasion. Recommend the replacement of any such line cord to the customer. 6. Check the B+ voltage to see it is at the values specified. 7. Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. CAUTION: The use of optical instrument with this product will increase eye hazard. To Exposed Metal Parts on Set 0.15 µF 1.5 kΩ CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. AC voltmeter (0.75 V) Earth Ground Fig. A. Using an AC voltmeter to check AC leakage. This label is located on the laser protective housing inside the enclosure. WARNING!! WHEN SERVICING, DO NOT APPROACH THE LASER EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO CONFIRM LASER BEAM EMISSION, BE SURE TO OBSERVE FROM A DISTANCE OF MORE THAN 25 cm FROM THE SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK. This appliance is classified as a CLASS1 LASER product. The CLASS1 LASER PRODUCT MARKING is located on the laser protective housing inside the enclosure. Unleaded solder Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.) : LEAD FREE MARK Unleaded solder has the following characteristics. • Unleaded solder melts at a temperature about 40°C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350°C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! • Strong viscosity Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. • Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder. SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ! LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY. –2– TABLE OF CONTENTS Section Title Page Section SERVICE NOTE 1. 5. DISC REMOVAL PROCEDURE IF THE TRAY CANNOT BE EJECTED (FORCED EJECTION) .......... INSTALLATION METHOD OF EARTH SPRING (FRONT) ........................................................................ INSTALLATION METHOD OF REAR GASKET ............ INSTALLATION METHOD OF NON-HALOGENE TAPE .............................................................................. TEST DISC .................................................................... 1. GENERAL 2. 3. 4. This Player Can Play the Following Discs and Files .... Main Features ................................................................ Getting Started .............................................................. Basic Operations ........................................................... Watching Movie Files .................................................... Listening to Music Files ................................................. Viewing Photo Files ....................................................... Changing the Initial Settings ......................................... Additional Information ................................................... 2. 3. BLOCK DIAGRAMS 3-1. 3-2. 3-3. 3-4. 3-5. 3-6. 3-7. Main Diagram ................................................................ Audio Block Diagram ..................................................... FL/FR Block Diagram .................................................... Power 1 Block Diagram ................................................. Power 2 Block Diagram ................................................. Power 3 Block Diagram ................................................. Power 4 Block Diagram ................................................. Page 4. SCHEMATIC DIAGRAMS AND PRINTED WIRING BOARDS 4-1. 4-2. Frame Schematic Diagram ............................................ Printed Wiring Boards and Schematic Diagrams ......... AU-258 (ANALOG AUDIO) Schematic Diagram ........... AU-258 Printed Wiring Board ........................................ FL-176 Printed Wiring Board ........................................ FL-176 (FL/LED) Schematic Diagram .......................... FR-271 Printed Wiring Board ........................................ FR-271 (SW/IR, INPUT/LED) Schematic Diagram ...... 5. TROUBLESHOOTING 4 4 4 5 5 1-1 1-1 1-2 1-4 1-7 1-8 1-9 1-10 1-13 Main Set, Power Supply Section ................................... Operation&Display Section ........................................... Audio Section ................................................................ FL Section ..................................................................... 6. 2-1 2-1 2-1 2-2 2-2 2-3 2-3 2-4 2-4 2-5 2-5 2-5 2-6 2-6 2-7 2-7 3-1 3-3 3-5 3-7 3-9 3-11 3-13 –3– 4-1 4-5 4-5 4-7 4-11 4-13 4-15 4-17 5-1 5-9 5-13 5-14 REPAIR PARTS LIST 6-1. Exploded Views ............................................................. 6-1-1. Case Assy ................................................................ 6-1-2. Main Chassis Block .................................................. 6-1-3. Main Block ................................................................ 6-2. Electrical Parts List ....................................................... DISASSEMBLY AND REASSEMBLY 2-1. DISASSEMBLY .............................................................. 2-1-1. Disassembly Flow ......................................................... 2-1-2. Upper Case ................................................................... 2-1-3. Tray Cover Assy ............................................................ 2-1-4. BD Drive (Service Use) ................................................. 2-1-5. MAIN Board ................................................................... 2-1-6. AU-258 Board ................................................................ 2-1-7. Power Block ................................................................... 2-1-8. Circuit Boards Location ................................................. 2-2. REASSEMBLY ............................................................... 2-2-1. Upper Case ................................................................... 2-2-2. Tray Cover Assy ............................................................ 2-2-3. BD Drive (Service Use) ................................................. 2-2-4. MAIN Board ................................................................... 2-2-5. FL-176 Board/FR-271 Board ........................................ 2-2-6. DC FAN .......................................................................... Title 6-1 6-1 6-2 6-3 6-4 SERVICE NOTE 1. DISC REMOVAL PROCEDURE IF THE TRAY CANNOT BE EJECTED (FORCED EJECTION) 1. Remove the upper case. (Refer to page 2-1) 2. Insert a clip in the hole of a drive and open a tray. clip tray 2. INSTALLATION METHOD OF EARTH SPRING (FRONT) 1. Please install earth spring (front) at an installation position of right and left in a front frame. Please be careful to directions of installation. 2. Please fix by for each one place with a screw. earth spring (front) 3. INSTALLATION METHOD OF REAR GASKET 1. Please remove a rear panel fixed screw and jack fixed screw (total 9 screws) and remove a rear panel. 2. Please stick a rear gasket inside the lower part of a rear panel. Refer to a lower picture. The location of the gasket is between the optical terminal and the audio terminal. 3. Please install a rear panel in the chassis from the slanting bottom and install a removed screws. rear gasket –4– 4. INSTALLATION METHOD OF NON-HALOGENE TAPE 1. Please connect a drive power supply harness after an exchange of a drive and fix by a reuse clamp. 2. Please stick a non-halogene tape so that a power supply harness may be fixed on the drive back. non-halogene tape 5. TEST DISC Part No. Description Layer J-6090-199-A J-6090-200-A 3-702-101-01 J-6090-088-A J-6090-089-A J-6090-077-A J-6090-078-A BLX-104 BLX-204 CD (YEDS-18) HLX-504 HLX-505 HLX-506 HLX-507 Single Layer Dual Layer Single Layer (NTSC) Dual Layer (NTSC) Single Layer (PAL) Dual Layer (PAL) 5-1. Operation and Display Check Items 1) BLX-104 1. Select 23.976Hz 1080p 2. Play “4.Motion pictures” 3. Check whether player can play back or not 4. Check each outputs Video: Composite/S Video/ component/HDMI Audio: Digital out(Coaxial/Optical)/Audio out/5.1Ch output * When 1080/24p monitor is nothing, 1080i(59.94Hz or 50Hz) can use instead of 1080/24p. However this is temporary correspondence. 2) BLX-204 1. Select 1080i(59.94Hz or 50Hz) 2. Play “4.Motion pictures” 3. Check whether player can play back or not (Check the picture and sound output) 3) CD (YEDS-18) Check whether player can play back or not (Check the sound output) 4) HLX-504/505(NTSC) HLX506/507(PAL) 1. After displayed Main Menu, select “1.Video” 2. Play “1.Color Bar 100%” (Check the picture and sound output) 3. Return to Menu 4. Play “Demonstration 4:3” or “5.Demonstration 16:9” (Check the picture and sound output) –5– 5-1-1. BLX-104 Menu Function (1) Main Menu X X X X X X X X X X X X X X X X 1) When the disc is inserted, 1. Video Signal of 59.94Hz/1080i of the Main Menu is selectively displayed. 5-1-2. BLX-104 Menu Function (2) Main Menu To Main Menu after playback of T62_C1 To Main Menu after playback of T61_C1 To Main Menu after playback from T54_C1 to T60_C1 Sub_menu3 is displayed To Main Menu after playback of T21_C1 To Main Menu after playback of T20_C1 To Main Menu after playback from T2_C1 to T19_C1 Sub_menu1 is displayed * When returning to Main Menu after playback from each button of 59.94Hz/1080i, 1. Video Signal of 59.94Hz/1080i is selectively displayed. * When returning to Main Menu after playback from each button of 50Hz/1080i, 1. Video Signal of 50Hz/1080i is selectively displayed. * 5. AV Sync does not operate. Note: Txx_ Cxx Chapter No. Title No. –6– 5-1-3. BLX-104 Menu Function (3) Main Menu To Main Menu after playback of T52_C1 To Main Menu after playback of T51_C1 To Main Menu after playback from T44_C1 to T50_C1 Sub_menu2 is displayed To Main Menu after playback of T42_C1 To Main Menu after playback of T41_C1 To Main Menu after playback from T23_C1 to T40_C1 Sub_menu4 is displayed * When returning to Main Menu after playback from each button of 59.94Hz/720P, 1. Video Signal of 59.94Hz/720P is selectively displayed. * When returning to Main Menu after playback from each button of 23.976Hz/1080P, 1. Video Signal of 23.976Hz/1080P is selectively displayed. * 5. AV Sync does not operate. –7– 5-1-4. BLX-104 Menu Function (4) Sub menu1 X X X X X X 1) At the display of Sub menu1, 1. Color Bar 100% is selectively displayed. 2) Selection of 1. Color Bar 100% t Return to Sub menu1 after seamless playback from T1_C1 to T1_C13. 1. Color Bar 100% is selectively displayed on Sub menu1 screen. 3) Selection of 2. Color Bar 75% t Return to Sub menu1 after seamless playback from T1_C2 to T1_C13. 1. Color Bar 100% is selectively displayed on Sub menu1 screen. 4) At the selection of 3 - 13, item 3 mentioned above is executed as the routine. 5) At the display of Sub menu1, Main Menu is selected t Jump to Main Menu. At the display of Main Menu, 1. Video Signal of 59.94Hz/1080i is selectively displayed. 6) Selection of LPCM Audio t Playback from T2_C1 to T19_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed. During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to Sub menu1 after playback. 1. Color Bar 100% is selectively displayed on Sub menu1 screen. 7) Selection of Dolby AC-3 Audio t Playback of T20_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed. During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to Sub menu1 after playback. 1. Color Bar 100% is selectively displayed on Sub menu1 screen. 8) Selection of Motion Picture t Return to Sub menu1 after playback of T21_C1. 1. ColorBar 100% is selectively displayed on Sub menu1 screen. 9) At the selection of Main Manu, 1. VideoSignal of 1080/59.94i of Main Menu is selectively displayed. 10) AV Sync does not operate. –8– 5-1-5. BLX-104 Menu Function (5) Sub menu2 X X X X X X 1) At the display of Sub menu2, 1. Color Bar 100% is selectively displayed. 2) Selection of 1. Color Bar 100% t Return to Sub menu2 after seamless playback from T43_C1 to T43_C13. 1. Color Bar 100% is selectively displayed on Sub menu2 screen. 3) Selection of 2. Color Bar 75% t Return to Sub menu2 after seamless playback from T43_C2 to T43_C13. 1. Color Bar 100% is selectively displayed on Sub menu2 screen. 4) At the selection of 3 - 13, item 3 mentioned above is executed as the routine. 5) At the display of Sub menu2, Main Menu is selected t Jump to Main Menu. At the display of Main Menu, 1. Video Signal of 23.976Hz/1080P is selectively displayed. 6) Selection of LPCM Audio t Playback from T44_C1 to T50_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed. During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to Sub menu2 after playback. 1. Color Bar 100% is selectively displayed on Sub menu2 screen. 7) Selection of Dolby AC-3 Audio t Playback of T51_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed. During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to Sub menu2 after playback. 1. Color Bar 100% is selectively displayed on Sub menu2 screen. 8) Selection of Motion Picture t Return to Sub menu2 after playback of T52_C1. 1. Color Bar 100% is selectively displayed on Sub menu2 screen. 9) At the selection of Main Manu, 1. Video Signal of 1080/23.976P of Main Menu is selectively displayed. 10) AV Sync does not operate. –9– 5-1-6. BLX-104 Menu Function (6) Sub menu3 X X X X X X 1) At the display of Sub menu3, 1. Color Bar 100% is selectively displayed. 2) Selection of 1. Color Bar 100% t Return to Sub menu3 after seamless playback from T53_C1 to T53_C13. 1. Color Bar 100% is selectively displayed on Sub menu3 screen. 3) Selection of 2. Color Bar 75% t Return to Sub menu3 after seamless playback from T53_C2 to T53_C13. 1. Color Bar 100% is selectively displayed on Sub menu3 screen. 4) At the selection of 3 - 13, item 3 mentioned above is executed as the routine. 5) At the display of Sub menu3, Main Menu is selected t Jump to Main Menu. At the display of Main Menu, 1. Video Signal of 50Hz/ 1080i is selectively displayed. 6) Selection of LPCM Audio t Playback from T54_C1 to T60_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed. During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to Sub menu3 after playback. 1. Color Bar 100% is selectively displayed on Sub menu3 screen. 7) Selection of Dolby AC-3 Audio t Playback of T61_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed. During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to Sub menu3 after playback. 1. Color Bar 100% is selectively displayed on Sub menu3 screen. 8) Selection of Motion Picture t Return to Sub menu3 after playback of T62_C1. 1. Color Bar 100% is selectively displayed on Sub menu3 screen. 9) At the selection of Main Manu, 1. Video Signal of 1080/50i of Main Menu is selectively displayed. 10) AV Sync does not operate. – 10 – 5-1-7. BLX-104 Menu Function (7) Sub menu4 X X X X X X 1) At the display of Sub menu4, 1. Color Bar 100% is selectively displayed. 2) Selection of 1. Color Bar 100% t Return to Sub menu4 after seamless playback from T22_C1 to T22_C13. 1. Color Bar 100% is selectively displayed on Sub menu4 screen. 3) Selection of 2. Color Bar 75% t Return to Sub menu4 after seamless playback from T22_C2 to T22_C13. 1. Color Bar 100% is selectively displayed on Sub menu4 screen. 4) At the selection of 3 - 13, item 3 mentioned above is executed as the routine. 5) At the display of Sub menu4, Main Menu is selected t Jump to Main Menu. At the display of Main Menu, 1. Video Signal of 59.94Hz/720P is selectively displayed. 6) Selection of LPCM Audio t Playback from T44_C1 to T50_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed. During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to Sub menu4 after playback. 1. Color Bar 100% is selectively displayed on Sub menu4 screen. 7) Selection of Dolby AC-3 Audio t Playback of T51_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed. During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to Sub menu4 after playback. 1. Color Bar 100% is selectively displayed on Sub menu4 screen. 8) Selection of Motion Picture t Return to Sub menu4 after playback of T52_C1. 1. Color Bar 100% is selectively displayed on Sub menu4 screen. 9) At the selection of Main Manu, 1. Video Signal of 720/59.94P of Main Menu is selectively displayed. 10) AV Sync does not operate. – 11 – 5-2-1. BLX-204 Menu Function (1) Main Menu X X X X X X X X X X X X X X X X X X 1) When the disc is inserted, 1. Video Signal of 59.94Hz/1080i of the Main Menu is selectively displayed. 2-2-2. BLX-204 Menu Function (2) Main Menu To Main Menu after playback of T83_C1 To Main Menu after playback of T62tT82 To Main Menu after playback of T61_C1 To Main Menu after playback of T54_C1-T60_C1tT83_C1-T94_C1 Sub_menu3 is displayed To Main Menu after playback of T67_C1 To Main Menu after playback of T21tT63tT64tT65tT66 To Main Menu after playback of T20_C1 To Main Menu after playback from T2_C1 to T19_C1 Sub_menu1 is displayed * When returning to Main Menu after playback from each button of 59.94Hz/1080i, 1. Video Signal of 59.94Hz/1080i is selectively displayed. * When returning to Main Menu after playback from each button of 50Hz/1080i, 1. Video Signal of 50Hz/1080i is selectively displayed. Note: Txx_ Cxx Chapter No. Title No. – 12 – 5-2-3. BLX-204 Menu Function (3) Main Menu To Main Menu after playback of T70_C1 To Main Menu after playback of T52_C1tT69 To Main Menu after playback of T51_C1 To Main Menu after playback of T44_C1-T50_C1tT71_C1-T81_C1 Sub_menu2 is displayed To Main Menu after playback of T68_C1 To Main Menu after playback of T42_C1 To Main Menu after playback of T41_C1 To Main Menu after playback from T23_C1 to T40_C1 Sub_menu4 is displayed * When returning to Main Menu after playback from each button of 59.94Hz/720P, 1. Video Signal of 59.94Hz/720P is selectively displayed. * When returning to Main Menu after playback from each button of 23.976Hz/1080P, 1. Video Signal of 23.976Hz/1080P is selectively displayed. – 13 – 5-2-4. BLX-204 Menu Function (4) Sub menu 1 X X X X X X 1) At the display of Sub menu1, 1. Color Bar 100% is selectively displayed. 2) Selection of 1. Color Bar 100% t Return to Sub menu1 after seamless playback from T1_C1 to T1_C13. 1. Color Bar 100% is selectively displayed on Sub menu1 screen. 3) Selection of 2. Color Bar 75% t Return to Sub menu1 after seamless playback from T1_C2 to T1_C13. 1. Color Bar 100% is selectively displayed on Sub menu1 screen. 4) At the selection of 3 - 13, item 3 mentioned above is executed as the routine. 5) At the display of Sub menu1, Main Menu is selected t Jump to Main Menu. At the display of Main Menu, 1. Video Signal of 59.94Hz/1080i is selectively displayed. 6) Selection of LPCM Audio t Playback from T2_C1 to T19_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed. During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to Sub menu1 after playback. 1. Color Bar 100% is selectively displayed on Sub menu1 screen. 7) Selection of Dolby AC-3 Audio t Playback of T20_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed. During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to Sub menu1 after playback. 1. Color Bar 100% is selectively displayed on Sub menu1 screen. 8) Selection of Motion Picture t Return to Sub menu1 after playback of T21_C1. 1. Color Bar 100% is selectively displayed on Sub menu1 screen. 9) Selection of AV Sync t Return to Sub menu1 after playback of T67_C1. 1. Color Bar 100% is selectively displayed on Sub menu1 screen. 10) At the selection of Main Manu, 1. Video Signal of 1080/59.94i of Main Menu is selectively displayed. – 14 – 5-2-5. BLX-204 Menu Function (5) Sub menu 2 X X X X X X 1) At the display of Sub menu2, 1. Color Bar 100% is selectively displayed. 2) Selection of 1. Color Bar 100% t Return to Sub menu2 after seamless playback from T43_C1 to T43_C13. 1. Color Bar 100% is selectively displayed on Sub menu2 screen. 3) Selection of 2. Color Bar 75% t Return to Sub menu2 after seamless playback from T43_C2 to T43_C13. 1. Color Bar 100% is selectively displayed on Sub menu2 screen. 4) At the selection of 3 - 13, item 3 mentioned above is executed as the routine. 5) At the display of Sub menu2, Main Menu is selected t Jump to Main Menu. At the display of Main Menu, 1. Video Signal of 23.976Hz/1080P is selectively displayed. 6) Selection of LPCM Audio t Playback from T44_C1 to T50_C1 and from T71_C1 to T81_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed. During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to Sub menu2 after playback. 1. Color Bar 100% is selectively displayed on Sub menu2 screen. 7) Selection of Dolby AC-3 Audio t Playback of T51_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed. During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to Sub menu2 after playback. 1. Color Bar 100% is selectively displayed on Sub menu2 screen. 8) Selection of Motion Picture t Return to Sub menu2 after playback of T52_C1 and T69. 1. Color Bar 100% is selectively displayed on Sub menu2 screen. 9) Selection of AV Sync t Return to Sub menu2 after playback of T70_C1. 1. Color Bar 100% is selectively displayed on Sub menu2 screen. 10) At the selection of Main Manu, 1. Video Signal of 1080/23.976P of Main Menu is selectively displayed. – 15 – 5-2-6. BLX-204 Menu Function (6) Sub menu 3 X X X X X X 1) At the display of Sub menu3, 1. Color Bar 100% is selectively displayed. 2) Selection of 1. Color Bar 100% t Return to Sub menu3 after seamless playback from T53_C1 to T53_C13. 1. Color Bar 100% is selectively displayed on Sub menu3 screen. 3) Selection of 2. Color Bar 75% t Return to Sub menu3 after seamless playback from T53_C2 to T53_C13. 1. Color Bar 100% is selectively displayed on Sub menu3 screen. 4) At the selection of 3 - 13, item 3 mentioned above is executed as the routine. 5) At the display of Sub menu3, Main Menu is selected t Jump to Main Menu. At the display of Main Menu, 1. Video Signal of 50Hz/ 1080i is selectively displayed. 6) Selection of LPCM Audio t Playback from T54_C1 to T60_C1 and from T84_C1 to T94_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed. During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to Sub menu3 after playback. 1. Color Bar 100% is selectively displayed on Sub menu3 screen. 7) Selection of Dolby AC-3 Audio t Playback of T61_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed. During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to Sub menu3 after playback. 1. Color Bar 100% is selectively displayed on Sub menu3 screen. 8) Selection of Motion Picture t Return to Sub menu3 after playback of T62_C1tT82. 1. Color Bar 100% is selectively displayed on Sub menu3 screen. 9) Selection of AV Sync t Return to Sub menu3 after playback of T83_C1. 1. Color Bar 100% is selectively displayed on Sub menu3 screen. 10) At the selection of Main Manu, 1. Video Signal of 1080/50i of Main Menu is selectively displayed. – 16 – 5-2-7. BLX-204 Menu Function (7) Sub menu 4 X X X X X X 1) At the display of Sub menu4, 1. Color Bar 100% is selectively displayed. 2) Selection of 1. Color Bar 100% t Return to Sub menu4 after seamless playback from T22_C1 to T22_C13. 1. Color Bar 100% is selectively displayed on Sub menu4 screen. 3) Selection of 2. Color Bar 75% t Return to Sub menu4 after seamless playback from T22_C2 to T22_C13. 1. Color Bar 100% is selectively displayed on Sub menu4 screen. 4) At the selection of 3 - 13, item 3 mentioned above is executed as the routine. 5) At the display of Sub menu4, Main Menu is selected t Jump to Main Menu. At the display of Main Menu, 1. Video Signal of 59.94Hz/720P is selectively displayed. 6) Selection of LPCM Audio t Playback from T44_C1 to T50_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed. During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to Sub menu4 after playback. 1. Color Bar 100% is selectively displayed on Sub menu4 screen. 7) Selection of Dolby AC-3 Audio t Playback of T51_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed. During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to Sub menu4 after playback. 1. Color Bar 100% is selectively displayed on Sub menu4 screen. 8) Selection of Motion Picture t Return to Sub menu4 after playback of T52_C1. 1. Color Bar 100% is selectively displayed on Sub menu4 screen. 9) Selection of AV Sync t Return to Sub menu4 after playback of T68_C1. 1. Color Bar 100% is selectively displayed on Sub menu4 screen. 10) At the selection of Main Manu, 1. Video Signal of 720/59.94P of Main Menu is selectively displayed. – 17 – MEMO – 18 – BDP-S300/S301 SECTION 1 GENERAL About this manual Instructions in this manual describe the controls on the remote. You can also use the controls on the player if they have the same or similar names as those on the remote. The meanings of the icons used in this manual are described below: Icon Examples of discs that the player cannot play This Player Can Play the Following Discs and Files The player cannot play the following discs: • BD-REs/BD-Rs. • BDs with cartridge. • DVD-RWs/DVD-Rs of VR mode. • DVD-RAMs. • HD DVDs. • DVD Audio discs. • DATA CDs (CD-Rs/CD-RWs other than music CD format). • CD-ROMs recorded in PHOTO CD format. • Data part of CD-Extras. • VCDs/Super VCDs. • HD layer on Super Audio CDs. Disc Format Meaning Functions available for BD-ROMs including DL discs. Blu-ray Disc DVD Functions available for DVD VIDEOs and DVD+RWs/DVD+Rs in +VR mode or DVD-RWs/DVD-Rs in video mode, including 8 cm discs. DVD VIDEO DATA DVD Functions available for DATA DVDs (DVD+RWs/DVD+Rs/DVD-RWs/DVDRs containing MPEG-2 PS movie files, MP3* audio tracks, and JPEG image files). CD Functions available for music CDs or CDRs/CD-RWs in music CD Format. BD * MP3 (MPEG-1 Audio Layer III) is a standard format defined by ISO (International Organization for Standardization)/IEC (International Electrotechnical Commission) MPEG which compresses audio data. Note The on-screen display illustrations used in this manual may not match the graphics displayed on your TV screen. This section is extracted from instruction manual (3-196-787-11). DVD-RW/-R Also, the player cannot play the following discs: • A BD-ROM/DVD VIDEO with a different region code. • A disc recorded in a color system other than NTSC, such as PAL (this player conforms to the NTSC color system). • A disc that has a non-standard shape (e.g., card, heart). • A disc with paper or stickers on it. • A disc that has the adhesive of cellophane tape or a sticker still left on it. DVD+RW/+R CD Notes “Blu-ray Disc” is a trademark. “Blu-ray Disc,” “DVD+RW,” “DVD-RW,” “DVD+R,” “DVDR,” “DVD VIDEO,” and “CD” logos are trademarks. • Notes about DVD+RWs/DVD+Rs, DVD-RWs/DVD-Rs, or CD-Rs/ CD-RWs Some DVD+RWs/DVD+Rs, DVD-RWs/DVD-Rs, or CD-Rs/ CD-RWs cannot be played on this player due to the recording quality or physical condition of the disc, or the characteristics of the recording device and authoring software. The DVD disc will not play if it has not been correctly finalized. For more information, refer to the operating instructions for the recording device. Note that some playback functions may not work with some DVD+RWs/DVD+Rs, even if they have been correctly finalized. In this case, view the disc by normal playback. Supported file formats (DATA DVD only) DVD+RWs/DVD-RWs/DVD+Rs/DVD-Rs are called “DATA DVD” in this manual when the discs contain playable files. The following file formats are supported: • MPEG-2 PS movie files. • MP3 music files. • JPEG* image files. * JPEG format conforming to UDF (Universal Disk Format). • Music discs encoded with copyright protection technologies This product is designed to playback discs that conform to the Compact Disc (CD) standard. Recently, various music discs encoded with copyright protection technologies are being marketed by some record companies. Please be aware that among those discs, there are some that do not conform to the CD standard and may not be playable by this product. Notes about BD-ROM compatibility This player supports BD-ROM Profile 1 only. Playback of later versions and BDs other than BD-ROM is not guaranteed. Since the Blu-ray Disc specifications are new and evolving, some discs may not play depending on the disc type and the version. The audio output differs depending on the source, connected output jack, and selected audio settings. For details, see page 48. • Note on DualDiscs A DualDisc is a two sided disc product which mates DVD recorded material on one side with digital audio material on the other side. However, since the audio material side does not conform to the Compact Disc (CD) standard, playback on this product is not guaranteed. • Note about double-layer DVDs The playback pictures and sound may be momentarily interrupted when the layers switch. ,continued 6 5 HDMI (High-Definition Multimedia Interface) digital interface Main Features BD/DVD region code When connected to an HDMI-equipped display device using a single HDMI cord, the player can output both SD to HD video and multi-channel audio signals, in digital form without degradation. The HDMI specification supports HDCP (High-bandwidth Digital Content Protection), a copy protection technology that incorporates coding technology for digital video signals. Your player has a region code printed on the back of the unit and only will play BD-ROM/DVD VIDEOs (playback only) labeled with identical region codes. This system is used to protect copyrights. DVD VIDEOs labeled will also play on this player. ALL Depending on the BD-ROM/DVD VIDEO, there may be no region code indication, even though playing the BD-ROM/DVD VIDEO is prohibited by area restrictions. 1 COMPONENT VIDEO OUT 1 VIDEO OUT DIGITAL OUT VIDEO AC IN PB HDMI OUT PR S VIDEO PCM/DTS/DOLBY DIGITAL COAXIAL OPTICAL 5.1CH OUTPUT AUDIO OUT Y FRONT L L R R REAR CENTER WOOFER Note on playback operations of BDs/ DVDs Some playback operations of BDs/DVDs may be intentionally set by software producers. Since this player plays BDs/DVDs according to the disc contents the software producers designed, some playback features may not be available. Also, refer to the instructions supplied with the BDs/DVDs. Copyrights This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited. Experience the high definition (HD) quality audio/video output and the library function of this Blu-ray Disc Player. Library function for recorded files (For JPEG image, MP3 audio, MPEG-2 PS movie files only) BD-ROM playback BD-ROM is a next generation optical disc format in the HD era. Featuring massive storage capacity of 25 to 50 GB (five times larger than a DVD) and a high-speed transfer rate of up to 54 Mbps, the format offers not only uncompromised HD quality video*1*2, but also enables rich bonus content on a single disc and HD quality audio up to 8ch, and interactive operability. With DATA DVDs created on other DVD devices, three separate movie/music/photo Title List-browsers allow for easy sorting, searching and playback including a slideshow. *1 A compatible HD display device is necessary to enjoy the same quality. *2 Some discs allow viewing only with an HDMI connection. 24p True Cinema Movies shot with a film camera consist of 24 frames per second. Since conventional televisions (both CRT and flat panels) display frames either at 1/60 or 1/50 second intervals, the 24 frames do not appear at an even pace. When connected to a TV with 24p capabilities, the player displays each frame at 1/24 second intervals — the same interval originally shot with the film camera, thus faithfully reproducing the original cinema image. HDMI Control (‘BRAVIA’ Theatre Sync) ‘BRAVIA’ Theatre Sync Function makes operations simple by connecting Sony components that are compatible with the HDMI Control function with an HDMI cord. BD-J application The BD-ROM format supports Java for interactive functions. “BD-J” offers content providers almost unlimited functionality when creating interactive BD-ROM titles*. Java and all Java-based trademarks and logos are trademarks or registered trademarks of Sun Microsystems, Inc. in the U.S. and other countries. Esmertec and Jbed are trademarks or registered trademarks of Esmertec AG. © 2000-2007 Esmertec AG * This player does not support downloadable BD-J content. Support of uncompressed multi-channel Linear PCM In combination with a compatible AV amplifier, the player can output up to 8ch Linear PCM surround sound*. With a noncompatible amplifier, the player can output 5.1ch analog signals from its 5.1CH OUTPUT jack for high quality audio enjoyment. * Note that the DIGITAL OUT (COAXIAL or OPTICAL) jack does not output 8ch signals. You will need an HDMI cord and an HDMIcompatible device that support 8ch signals. AVCHD format disc playback The player supports AVCHD format files–high definition recordings made on AVCHD-compatible camcorders. Your high definition personal archive is readily playable in HD quality. ,continued 8 7 1-1 About playback of discs recorded in AVCHD format This player can play AVCHD format discs. TM What is the AVCHD format? The AVCHD format is a high definition digital video camera format used to record SD (standard definition) or HD (high definition) signals of either the 1080i specification*1 or the 720p specification*2 on DVDs, using efficient data compression coding technology. The MPEG-4 AVC/H.264 format is adopted to compress video data, and the Dolby Digital or Linear PCM system is used to compress audio data. The MPEG-4 AVC/ H.264 format is capable of compressing images at higher efficiency than that of the conventional image compressing format. The MPEG-4 AVC/H.264 format enables a high definition (HD) video signal shot on a digital video camera recorder to be recorded on DVD discs, in the same way as it would be for a standard definition (SD) television signal. “AVCHD” and the AVCHD logo are trademarks of Matsushita Electric Industrial Co., Ltd. and Sony Corporation. *1 A high definition specification which utilizes 1080 effective scanning lines and the interlace system. *2 A high definition specification which utilizes 720 effective scanning lines and the progressive system. Notes • Some AVCHD format discs may not play, depending on the recording condition. • The AVCHD format disc will not play if it has not been correctly finalized. Step 1: Unpacking Getting Started B Connecting to an S VIDEO input jack Connect using an S VIDEO cord (not supplied). You will enjoy high quality images. Blu-ray Disc player Check that you have the following items: • Video cord (phono plug × 1) (1) • Stereo audio cord (phono plug × 2) (1) • HDMI cord (1) (supplied with BDP-S301 only) • Power cord (1) • Remote commander (remote) (1) • Size AA (R6) batteries (2) Notes • Plug cords securely to prevent unwanted noise. • Refer to the instructions supplied with the components to be connected. • You cannot connect this player to a TV that does not have a video input jack. • Be sure to disconnect the power cord of each component before connecting. • Do not apply too much pressure on the connecting cords. Pushing against the cabinet wall, etc., may damage the cord. Connect this player to your TV monitor, projector or AV amplifier (receiver) using a video cord. Select one of the patterns A through D, according to the input jack on your TV monitor, projector or AV amplifier (receiver). In order to view 1080p progressive signals with a compatible TV, projector, or monitor with an HDMI input jack, you must select pattern D. You can use pattern C to view 480p/720p progressive signals or 1080i interlace signals on a compatible device with component video input jacks. Getting Started Follow steps 1 to 7 to hook up and adjust the settings of the player. For jack and button names, see “Index to Parts and Controls” (page 58). Step 2: Connecting the Video Cords/HDMI Cord COMPONENT VIDEO OUT VIDEO OUT DIGITAL OUT PCM/DTS/DOLBY DIGITAL COAXIAL OPTICAL PB HDMI OUT 5.1CH OUTPUT AUDIO OUT Y VIDEO AC IN PR FRONT L L R R REAR CENTER S VIDEO WOOFER to S VIDEO VIDEO OUT VIDEO S VIDEO cord (not supplied) INPUT S VIDEO S VIDEO A Connecting to a video input jack Connect the supplied video cord (yellow) to the yellow (video) jack. You will enjoy standard quality images. TV, projector, or AV amplifier (receiver) : Signal flow Blu-ray Disc player COMPONENT VIDEO OUT VIDEO OUT DIGITAL OUT PCM/DTS/DOLBY DIGITAL COAXIAL OPTICAL PB HDMI OUT PR FRONT L L R R S VIDEO C Connecting to component video input jacks (Y, PB, PR) 5.1CH OUTPUT AUDIO OUT Y VIDEO AC IN REAR CENTER WOOFER to VIDEO OUT VIDEO OUT VIDEO (yellow) (yellow) S VIDEO INPUT VIDEO Video cord (supplied) Connect the component via the COMPONENT VIDEO OUT jacks using a component video cord (not supplied) or three video cords (not supplied) of the same kind and length. You will enjoy accurate color reproduction and high quality images. You can also enjoy higher quality pictures from 480p/720p progressive signals or 1080i interlace signals, if your TV, projector or AV amplifier (receiver) is compatible. L Blu-ray Disc player AUDIO R COMPONENT VIDEO OUT VIDEO OUT DIGITAL OUT PB : Signal flow When connecting to a standard 4:3 screen TV Depending on the disc, the image may not fit your TV screen. To change the aspect ratio, see page 45. HDMI OUT 5.1CH OUTPUT AUDIO OUT Y VIDEO AC IN TV, projector, or AV amplifier (receiver) PCM/DTS/DOLBY DIGITAL COAXIAL OPTICAL PR FRONT L L R R S VIDEO COMPONENT VIDEO OUT REAR CENTER WOOFER to COMPONENT VIDEO OUT (green) (green) COMPONENT VIDEO IN Y Y (blue) (blue) PB PB PR (red) (red) PR Note Do not connect a VCR, etc., between your TV and the player. If you pass the player signals via the VCR, you may not receive a clear image on the TV screen. If your TV has only one audio/video input jack, connect the player to this jack. Component video cord (not supplied) TV, projector, or AV amplifier (receiver) : Signal flow VCR • Step 1: Unpacking . . . . . . . . . . . . . . . . . . . . . . .9 Blu-ray Disc player • Step 2: Connecting the Video Cords/ HDMI Cord . . . . . . . . . . . . . . . . . . . . . . . . .10 TV Connect directly • Step 3: Connecting the Audio Cords . . . . . . . .12 • Step 4: Connecting the Power Cord . . . . . . . . .16 • Step 5: Preparing the Remote . . . . . . . . . . . . .16 • Step 6: Easy Setup. . . . . . . . . . . . . . . . . . . . . .18 • Step 7: Additional Adjustments . . . . . . . . . . . .19 9 D Connecting to an HDMI input jack Use an HDMI cord to enjoy high quality digital pictures and sound through the HDMI OUT jack. You will enjoy higher quality pictures from 480p/1080i, or 1080p (highest among the player output), if your TV, projector or AV amplifier (receiver) is compatible. Blu-ray Disc player COMPONENT VIDEO OUT VIDEO OUT DIGITAL OUT PB PR FRONT L L R R S VIDEO HDMI OUT REAR CENTER WOOFER to HDMI OUT HDMI cord (supplied with BDP-S301 only) TV, projector, or AV amplifier (receiver) HDMI IN This Blu-ray Disc player incorporates High-Definition Multimedia Interface (HDMI™) technology. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC. Notes on connecting to the HDMI OUT jack Observe the following as improper handling may damage the HDMI OUT jack and the connector. • Carefully align the HDMI OUT jack on the back of the player and the HDMI connector by checking their shapes. Make sure the connector is not upside down or tilted. About indicators for HDMI connection Step 3: Connecting the Audio Cords After the player is turned on, the HD indicator on the front panel lights up when outputting 720p/1080i/1080p video signals. The HDMI indicator lights up when an HDMI device is connected. Notes • Consumers should note that not all high definition television sets are fully compatible with this product and may cause artifacts to be displayed in the picture. In the case of 480/720/1080 progressive scan picture problems, it is recommended that the user switch the connection to the ‘standard definition’ output. If there are questions regarding our TV set compatibility with this model 480p/720p/1080p Blu-ray Disc player, please contact our customer service center. • If the picture is not clear, natural, or to your satisfaction, change the video output resolution by pressing VIDEO FORMAT (page 46). • Be sure to use only an HDMI cord that bears the HDMI logo. About the ‘BRAVIA’ Theatre Sync features (for HDMI connections only) Select the connection that best suits your system. Be sure to read the instructions for the components you wish to connect. Getting Started HDMI OUT PCM/DTS/DOLBY DIGITAL COAXIAL OPTICAL 5.1CH OUTPUT AUDIO OUT Y VIDEO AC IN 10 Connection Your setup A TV B Stereo amplifier (receiver) and two speakers By connecting Sony components that are compatible with the HDMI Control function with an HDMI cord, operation is simplified as below: • One-Touch Play (page 21) You can turn on the player and TV/AV receiver, set the TV/AV receiver’s input to the player, and start playback with one touch of the H button. • System Power-Off When you turn the TV off by using the POWER button on the TV’s remote, the HDMI compatible components turn off automatically. Notes about the HDMI OUT jack • When you connect the player to an AV amplifier (receiver) using an HDMI cord, you will need to do one of the following: – Connect the AV amplifier (receiver) to a TV with the HDMI cord. – Connect the player to the TV with a video cord other than an HDMI cord (component video cord, S VIDEO cord, or video cord). • When connecting to the HDMI OUT jack, carefully align the HDMI connector with the jack. Do not bend or apply pressure to the HDMI cord. • If you change the component connected to the HDMI OUT jack, change “Audio (HDMI)” in “Audio Setup” to match the new component (page 47). The player stores the HDMI related settings for up to five components. • The HDMI connection is compatible with 2ch Linear PCM signals (48 to 192 kHz, 16/20/24 bit), and 6 to 8ch Linear PCM signals (48 to 96 kHz, 16/20/24 bit), in addition to Dolby Digital and DTS bit stream (5.1ch signals up to 96 kHz, 16/20/ 24bit). Note If you connect a component that does not conform to the selected audio signal, a loud noise (or no sound) will come out from the speakers, which could damage your ears or speakers. C AV amplifier (receiver) having a Dolby*1 Surround (Pro Logic) decoder and 3 to 6 speakers • Surround effects: Dolby Surround (Pro Logic) To prepare for the ‘BRAVIA’ Theatre Sync features D-1 AV amplifier (receiver) with 5.1ch input jacks and 6 speakers • Surround effects: Dolby Digital (5.1ch), DTS (5.1ch) Set “HDMI Control” of “Options” setup to “On” (page 52). Note Depending on the connected component, the HDMI Control function may not work. Refer to the operating instructions supplied with the component. D-2 AV amplifier (receiver) with a digital input jack having a Dolby Digital or DTS*2 decoder and 6 speakers • Surround effects: Dolby Digital (5.1ch), DTS (5.1ch) MI HDUT O MI HDUT O D-3 • Be sure to disconnect the HDMI cord when moving the player. AV amplifier (receiver) with an HDMI input jack and 8 speakers • Surround effects: 8ch Linear PCM *1 *2 • If you place the player on the cabinet with the HDMI cord connected, do not apply too much pressure to the cabinet wall. It may damage the HDMI OUT jack or the HDMI cord. • When connecting or disconnecting, do not screw in or rotate the HDMI connector. 11 12 1-2 Manufactured under license from Dolby laboratories. “Dolby,” “Pro Logic,” and the double-D symbol are trademarks of Dolby Laboratories. “DTS” and “DTS Digital Surround” are registered trademarks of DTS, Inc. Connecting to your TV A This connection will use your TV’s speakers for sound. C Connecting to an AV amplifier (receiver) having a Dolby Surround (Pro Logic) decoder and 3 to 6 speakers B Connecting to a stereo amplifier (receiver) and 2 speakers If your stereo amplifier (receiver) only has audio input jacks L and R, use B-1 . If your amplifier (receiver) has a digital input jack, use B-2 . COMPONENT VIDEO OUT DIGITAL OUT PCM/DTS/DOLBY DIGITAL COAXIAL OPTICAL PB PR VIDEO OUT 5.1CH OUTPUT AUDIO OUT Y VIDEO HDMI OUT Getting Started Blu-ray Disc player Blu-ray Disc player COMPONENT VIDEO OUT VIDEO OUT AC IN FRONT REAR CENTER L R R DIGITAL OUT PCM/DTS/DOLBY DIGITAL COAXIAL OPTICAL AC IN PB HDMI OUT S VIDEO PR WOOFER 5.1CH OUTPUT AUDIO OUT Y VIDEO L FRONT L L R R REAR CENTER S VIDEO to AUDIO OUT L/R (white) AUDIO OUT B-2 L WOOFER B-1 DIGITAL OUT If your AV amplifier (receiver) only has L and R audio input jacks, use C-1 . If your amplifier (receiver) has a digital input jack, use C-2 . You can enjoy surround effects only when playing Dolby Surround audio or multi-channel audio (Dolby Digital or DTS) discs. If your AV amplifier (receiver) has 5.1 channel inputs, use D-1 . Blu-ray Disc player Blu-ray Disc player COMPONENT VIDEO OUT COMPONENT VIDEO OUT VIDEO OUT DIGITAL OUT PB HDMI OUT PCM/DTS/DOLBY DIGITAL COAXIAL OPTICAL PR FRONT L L R R REAR CENTER C-2 PR C-1 D-1 AUDIO OUT PCM/DTS/DOLBY DIGITAL COAXIAL OPTICAL FRONT L L R R S VIDEO WOOFER DIGITAL OUT DIGITAL OUT PCM/DTS/DOLBY DIGITAL COAXIAL OPTICAL PB HDMI OUT 5.1CH OUTPUT AUDIO OUT Y VIDEO AC IN S VIDEO L VIDEO OUT 5.1CH OUTPUT AUDIO OUT Y VIDEO AC IN AUDIO OUT PCM/DTS/DOLBY DIGITAL COAXIAL OPTICAL D-1 Connecting to an AV amplifier (receiver) with 5.1ch input jacks and 6 speakers REAR CENTER WOOFER 5.1CH OUTPUT FRONT L REAR CENTER L R (red) R R R TV WOOFER INPUT to AUDIO OUT L/R to DIGITAL OUT (COAXIAL or OPTICAL) Stereo audio cord (supplied) VIDEO to DIGITAL OUT (COAXIAL or OPTICAL) to AUDIO OUT L/R to 5.1CH OUTPUT (white) (white) L AUDIO (white) Optical digital cord (not supplied) (red) R (red) Stereo audio cord (supplied) Coaxial digital cord (not supplied) : Signal flow Optical digital cord (not supplied) or (white) (white) Monaural audio cord (not supplied) to audio input to audio input [Speakers] AV Amplifier (receiver) with a decoder Stereo amplifier (receiver) Stereo audio cord (one is supplied) (red) to coaxial or optical digital input to audio input [Speakers] [Speakers] Stereo audio cord (supplied) Coaxial digital cord (not supplied) (red) to coaxial or optical digital input (red) or [Speakers] AV amplifier (receiver) with 5.1ch inputs [Speakers] Front (L) Front (R) Rear (L) Rear (R) Rear (L) Center Front (R) Center Rear (R) Front (L) Front (R) : Signal flow Subwoofer Subwoofer Rear (mono) Front (L) : Signal flow : Signal flow z Hint z Hint For correct speaker location, see the operating instructions of the connected components. For correct speaker location, see the operating instructions of the connected components. Note When connecting 6 speakers, you do not need the “Rear (mono)” speaker above. ,continued 14 13 D-2 Connecting to an AV amplifier (receiver) with a digital input jack and 6 speakers If you want to use the Dolby Digital, or DTS decoder function on your AV amplifier (receiver), connect to its digital jack using D-2 . You can enjoy a more realistic audio presence. D-3 Connecting to an AV amplifier (receiver) with an HDMI input jack and 8 speakers If your AV amplifier (receiver) accepts 8ch Linear PCM input with an HDMI connection, you can enjoy the surround sound using D-3 . Blu-ray Disc player COMPONENT VIDEO OUT DIGITAL OUT PB PCM/DTS/DOLBY DIGITAL COAXIAL OPTICAL 5.1CH OUTPUT AUDIO OUT Y VIDEO HDMI OUT FRONT L L R R D-2 REAR VIDEO OUT CENTER HDMI OUT DIGITAL OUT PCM/DTS/DOLBY DIGITAL COAXIAL OPTICAL PR WOOFER 5.1CH OUTPUT AUDIO OUT Y VIDEO AC IN PB PR S VIDEO FRONT L L R R S VIDEO REAR CENTER WOOFER After all of the other connections are complete, connect the supplied power cord to the AC IN terminal of the player. Then plug the player and TV power cords into the AC outlet. Getting Started Blu-ray Disc player COMPONENT VIDEO OUT VIDEO OUT AC IN Step 4: Connecting the Power Cord Step 5: Preparing the Remote You can control the player using the supplied remote. Insert two Size AA (R6) batteries by matching the 3 and # ends on the batteries to the markings inside the battery compartment. When using the remote, point it at the remote sensor on the player (page 58). AC IN to AC IN D-3 DIGITAL OUT PCM/DTS/DOLBY DIGITAL COAXIAL OPTICAL HDMI OUT HDMI OUT HDMI cord (supplied with BDP-S301 only) or or to HDMI input HDMI cord (supplied with BDP-S301 only) to HDMI input to coaxial or optical digital input AV amplifier (receiver) having a decoder Center Subwoofer [Speakers] [Speakers] Rear (L) Rear (R) Notes • Do not leave the remote in an extremely hot or humid place. • Do not drop any foreign object into the remote casing, particularly when replacing the batteries. • Do not expose the remote sensor to direct sunlight or a lighting apparatus. Doing so may cause a malfunction. • If you do not use the remote for an extended period of time, remove the batteries to avoid possible damage from battery leakage and corrosion. Coaxial digital cord (not supplied) Optical digital cord (not supplied) [Speakers] to AC outlet to HDMI OUT to DIGITAL OUT (COAXIAL or OPTICAL) to HDMI OUT AV amplifier (receiver) with 8ch outputs Rear1 (L) Center Subwoofer Rear1 (R) Front (R) Rear2 (R) Rear2 (L) Front (L) [Speakers] Front (R) Front (L) : Signal flow z Hint z Hint For correct speaker location, see the operating instructions of the connected components. For correct speaker location, see the operating instructions of the connected components. Note Not all HDMI-compatible AV amplifiers (receivers) accept 8ch Linear PCM signals. See also the operating instructions supplied with the connected AV amplifier (receiver). 15 16 1-3 If you want to control your TV with the supplied remote You can control the volume, input source, and power switch of your Sony TV with the supplied remote. OPEN/ CLOSE DISPLAY TV/VIDEO DIMMER While holding down TV [/1, press the number buttons to select your TV manufacturer’s code (see the table below). 2 4 5 7 8 TV/VIDEO 2 Release TV [/1. 3 ◆Code numbers of controllable TVs If more than one code number is listed, try entering them one at a time until you find the one that works with your TV. 6 9 VIDEO FORMAT 0 CLEAR AUDIO SUBTITLE GREEN ANGLE BLUE YELLOW SYSTEM MENU TOP MENU POP UP/ MENU RETURN PREV SLOW/STEP SCAN Code number Sony 01 (default) Easy Setup SCAN PAUSE STOP PLAY MODE Start Cancel Follow the steps below to make the minimum number of basic adjustments for using the player. If you do not complete Easy Setup, it will appear each time you turn on your player. Make the settings below in the following order. Please use the Initial Setup if you want to make more detailed settings. Use Wait about 90 seconds before the player turns on and starts Easy Setup. The start-up time will be much shorter once Easy Setup is completed. ◆If the above display does not appear Go to step 6. This display appears only when the player is turned on for the first time. f Select the video output format for the Daewoo 22, 04 Emerson 14 GE 06 Hitachi 02, 04 JVC 09 1 2 3 LG/Gold star 03, 17, 04 4 5 6 MGA/Mitsubishi 13, 04 7 8 NEC 04, 12 CLEAR 0 connected TV, and press ENTER. OPEN/ CLOSE TV "/1 DIMMER DISPLAY TV/VIDEO For details about the video output, see page 46. ◆ When using the HDMI OUT jack Easy Setup Output Video Format 9 VIDEO FORMAT CH MUTING MUTING CH +/– Panasonic 19 Philips 08, 21 AUDIO RED VOL +/– Pioneer 16 RCA 10, 04 R.Shack 05 Samsung 04, 12, 20 Sanyo 11 Sharp 05, 18 Toshiba 07, 18 Zenith 15 By pressing You can TV [/1 Turn the TV on or off. VOL +/– Adjust the volume of the TV. ◆To return the remote to its default settings TV/VIDEO Switch the TV’s input source between the TV and other input sources. Select the channel up and down. 1 2 Remove the batteries from the remote. CH +/– MUTING Mute the sound (for Sony TV only). 3 Wait for a few seconds. to select then press ENTER. Confirm SYSTEM MENU Exit When turned on for the first time NEXT PLAY VOL Manufacturer “Easy Setup.” Before using, make some simple settings for the BD player. Getting Started 1 RED 1 e Select “Start,” and press ENTER to start Step 6: Easy Setup You can control the volume, input source, and power switch of nonSony TVs as well. If your TV is listed in the table below, set the appropriate manufacturer’s code. TV TV \/1 Number buttons To control other TVs with the remote SUBTITLE GREEN Auto 480i 480p 720p 1080i 1080p Source Direct ANGLE BLUE YELLOW SYSTEM MENU TOP MENU Select [Auto] to automatically match the video output format with the HDMI-connected TV. Confirm SYSTEM MENU Exit </M/m/,, ENTER RETURN PREV Select from “Auto,” “480i,” “480p,” “720p,” “1080i,” “1080p,” or “Source Direct,” then go to step 8. “TV Type” in step 7 will be set to “16:9” (wide screen). POP UP/ MENU SLOW/STEP NEXT ◆ When using the jacks other than the HDMI OUT jack a Turn on the TV. b Press [/1 to turn on the player. Easy Setup The player turns on after a moment. Re-insert the batteries while pressing down 1, 2, and 3 of the number buttons. Output Video Format S-Video/Video only 480i 480p 720p 1080i Don't Know c Switch the input selector on your TV so that the signal from the player appears on your TV screen. Note Select [Auto] to automatically match the video output format with the HDMI-connected TV. If the display for OSD language selection does not appear, select “Start” of “Easy Setup” in “Options” Setup (page 52). Depending on the connected unit, you may not be able to control your TV using all or some of the buttons on the supplied remote. Confirm SYSTEM MENU Exit Select from “S-Video/Video only,” “480i,” “480p,” “720p,” “1080i” or “Don’t Know.” If you select “720p” or “1080i,” go to step 8. “TV Type” in step 7 will be set to “16:9” (wide screen). d Select the OSD language you want to display, and press ENTER. Easy Setup Language English Français Select the on-screen display language. Audio, subtitle and BD/DVD menu language options will be set to the same language as this. Confirm SYSTEM MENU Exit This will determine the Audio, Subtitle and BD/ DVD menu languages as well. 17 g Select the aspect ratio that matches your TV, and press ENTER. Easy Setup 18 Playing a Disc Step 7: Additional Adjustments TV Type 16:9 4:3 Basic Operations The following settings and adjustments are necessary when your connection applies. Confirm SYSTEM MENU Exit ◆ If you have a wide screen TV or a 4:3 standard TV with a wide screen mode Select “16:9” (page 45). ◆ If you have a 4:3 standard TV Select “4:3” (page 45). h Select “Finish Setup,” and press ENTER. ◆When using the HDMI OUT jack (Pattern D –page 11) • Select the video output resolution for your TV by pressing VIDEO FORMAT (page 46). • Select the type of video output from the HDMI OUT jack in “YCbCr/RGBPC (HDMI)” of “Video Setup” (page 45). Most of the BD playback operations are common to DVD. This section covers BD/ DVD/CD playback in general, together with the basic operation of the player. For browsing recorded files on DATA DVDs*, a separate library function is available. See also page 32 for movie, 36 for music, 40 for photo files. For operations using the remote, a complete list is located on page 24. For audio connection Easy Setup ◆When using the DIGITAL OUT (OPTICAL or COAXIAL) jack (Connection B-2 , C-2 , D-2 –page 13 to 15) • Set “Dolby Digital” and “DTS” in “Audio Setup” (page 47) according to your AV amplifier’s (receiver’s) decoder. Setup is complete! Enjoy using your BD player! Finish Setup Go Back Use ◆When using the COMPONENT VIDEO OUT jacks (Pattern C –page 10) • Select the video output resolution for your TV by pressing VIDEO FORMAT (page 46). Getting Started For video connection Select the screen aspect ratio to match your TV. to select then press ENTER. Confirm SYSTEM MENU Exit z Hints • If you want to reset these settings to their factory defaults, see “Resetting the Player” (page 53). • You can re-run “Easy Setup” from “Options” Setup (page 52). BD DVD CD Z OPEN/ CLOSE TV \/1 DIMMER Number buttons DISPLAY TV/VIDEO 1 2 4 5 7 8 CLEAR 0 3 6 9 VIDEO FORMAT AUDIO RED SUBTITLE GREEN ANGLE BLUE YELLOW SYSTEM MENU TOP MENU </M/m/,, ENTER RETURN * DVD+RWs/DVD+Rs/DVD-RWs/DVD-Rs containing MPEG-2 PS movie, MP3 audio, or JPEG image files. POP UP/MENU POP UP/ MENU RETURN PREV SLOW/STEP SCAN ◆When using the HDMI OUT jack (HDMI connection of D-2 , D-3 –page 15) • Set “Dolby Digital” and “DTS” in “Audio Setup” (page 47) according to your AV amplifier’s (receiver’s) decoder. • Select the audio output method from the HDMI OUT jack in “Audio (HDMI)” of “Audio Setup” (page 47). Color buttons TOP MENU SYSTEM MENU PLAY PAUSE NEXT SCAN STOP H PLAY MODE X VOL CH x MUTING ◆When using the AUDIO OUT (L/R) jacks (Connection C-1 –page 14) • Set “DTS Downmix” to “Lt/Rt” in “Audio Setup” (page 47). ◆When using the 5.1CH OUTPUT jacks (Connection D-1 –page 14) • Set “Audio Output Mode” to “5.1 Channel” in “Speakers” Setup (page 51), and adjust the “Speaker Setup” setting for your system. a Press \/1. The player turns on after a moment. Notes b Switch the input selector on your TV so that • If you connect a component that does not conform to the selected audio signal, a loud noise (or no sound) will come out from the speakers, which could damage your ears or speakers. • If you connect using the HDMI OUT jack or COMPONENT VIDEO OUT jacks and the picture does not appear clearly, the connected display device may not be compatible with the progressive signals. In this case, connect the display device to the S VIDEO jack or the VIDEO jack (pattern A or B – see page 10), re-run the “Easy Setup” from the “Options” Setup (page 52), and select “S-Video/Video only” in step 6 (page 18). Also, check the above items again to see if any additional adjustment is required. the signal from the player appears on your TV screen. c Press Z to open the disc tray. d Place a disc on the disc tray with the playback side facing down. • Playing a Disc. . . . . . . . . . . . . . . . . . . . . . . . . 20 • Guide to Displays . . . . . . . . . . . . . . . . . . . . . . 22 • Guide to the Remote. . . . . . . . . . . . . . . . . . . . 24 • Checking the Disc Information . . . . . . . . . . . . 26 • Clarifying Low Volume Sounds (Audio DRC) . 27 • Adjusting the Pictures . . . . . . . . . . . . . . . . . . 28 • Locking a Disc . . . . . . . . . . . . . . . . . . . . . . . . 29 20 19 1-4 Playback side facing down e Press Z to close the disc tray. Wait a short while until the disc type appears on the front panel display. f Press H to start playback. For more information about the remote’s operations, see page 24. Details X Pauses playback, or restarts playback from the same point. x Stops playback, or cancels the resume point when pressed twice. H Starts or restarts playback from the previous stop point. g When you finish playing, press Z to open the disc tray. h Remove the disc, and press Z again to close About One-Touch Play (for HDMI connections only) With one touch of the H button, the player and your TV/AV receiver automatically turn on and the TV/AV receiver’s input is switched to the player. Playback starts automatically. To use this function, set “HDMI Control” of “Options” setup to “On” (page 52). The TV/AV receiver’s input will also switch to the player automatically, in the following cases: – You press H, SYSTEM MENU, TOP MENU, or POP UP/ MENU buttons on the remote. – A disc with auto playback function is loaded. Title List Guide to Displays To prevent damage to your display device (ghosting), a screen saver image appears when the player is left unattended, has no disc inserted, or no title/slideshow is displayed for 15 minutes. To cancel, press any button on the remote or the player. For DATA DVDs, this display leads further to the Title Lists of content type. The three Title Lists appear similar and are operable in a similar way. Title List BD DVD DATA DVD CD Movies Photos When ‘Select an item, and press ENTER’ appears in this manual, press the </M/m/, keys on the remote to select the item then the entry button in the middle. You can operate the player likewise using displays. Basic Operations Buttons About the screen saver function Music Access the BD-R/RE titles. Select SYSTEM MENU Exit System Menu Select the Title List you want to view; from “Movies,” “Photos,” or “Music,” and press ENTER. Title List ◆Movies Displays movies/video titles only (page 32). A/V Control Setup ◆Photos Displays image files only (page 40). the disc tray. Search for the part you want to play from a list of the disc's content. Select SYSTEM MENU Exit i Press \/1 to turn off the player. a Press SYSTEM MENU to turn on the above “System Menu.” To use the BD’s or DVD’s menu The player’s start menu appears, with entries to all of the functions. When you play a BD-ROM, DVD VIDEO, or a finalized DVD+RW, DVD-RW (Video mode), DVD+R, or DVD-R (Video mode), you can display the disc’s menu by pressing TOP MENU or POP UP/MENU. Some BDs/DVDs display the menu automatically. Either cases, navigate through the menu using </M/m/,, ENTER, or the number buttons and the color buttons as indicated by the disc’s on-screen instructions. The BD menu is operable without interrupting playback. ◆Music Displays music files only (page 36). A/V Control (page 27) Adjusts the audio/video settings. Select either “Video Control,” or “Audio Control,” and press ENTER. b Select an item, and press ENTER. A/V Control Each item leads to the following function displays. See the pages in parentheses for operations. When you want to return to the previous display, press RETURN. Video Control Audio Control To play restricted BDs Set the playback picture quality. If “CAN’T PLAY” appears on the front panel display for a BDROM, change the “BD Parental Control” setting (page 30). Select SYSTEM MENU Exit Setup (page 44) To play restricted DVDs Enters the Setup displays for changing the player’s settings. Select the related Setup display, and press ENTER. For a restricted DVD, the display asks for the password. For “DVD Parental Control” setting, see page 30. 1 Enter your four-digit password using the number buttons. 2 Press ENTER to confirm. To register or change the password, see page 29. Setup Video Setup Audio Setup Language Parental Control Speakers Options Notes about Resume Play • Playback starts from the beginning if the title has not been played or the previous stop point is canceled. • The stop point is canceled when: – you change the settings on the player. – you turn off the player (BD-ROM and CD only). – you press x twice. – you open the disc tray. – you finish a search. • The player remembers the stop point for one title/track/file only. On a music CD, playback resumes from the beginning of the track. TV Type 4:3 Video Output DVD Aspect Ratio YCbCr/RGBPC(HDMI) 24p Output 16:9 Normal Letter Box Y, Cb, Cr Off Use to select an item, then press [RR] or ENTER. Confirm SYSTEM MENU Exit 22 21 Entering characters Guide to the Remote A Z OPEN/CLOSE (page 20) – Opens/closes the disc tray. DATA DVD TV &/1 (page 17) – Turns the TV on or to standby mode. When an on-screen keyboard appears (e.g., when searching for a title), enter the characters as follows. The following covers all of the remote’s functions. Refer to the list when necessary. s_ B L V 2 C M W 3 ( D N X 4 ) SHFT E O Y 5 F P Z 6 G Q , 7 H R . 8 I S : 9 J T ; 0 SPC DEL CLR DONE CANCEL a Select the character you want to enter, and press ENTER. The character appears in the entry field. If necessary, select the following items, and press ENTER. Items Details SHFT Switches between upper and lower case characters. Select this before entering the character. SPC Inserts a space. DEL Deletes the last character input. CLR Clears all input characters. OPEN/ CLOSE Basic Operations A K U 1 _ B DIMMER (page 59) – Changes the brightness of the front panel display on the player (when completely darkened, indicators on the front panel are also turned off and the FL OFF indicator lights up). TV DISPLAY TV/VIDEO DIMMER 1 2 4 5 6 7 8 9 CLEAR 0 3 AUDIO SUBTITLE GREEN ANGLE BLUE YELLOW SYSTEM MENU DISPLAY (page 26) – Displays the disc information on the screen. TV/VIDEO (page 17) – Switches between TV and other input sources. VIDEO FORMAT RED &/1 (page 18) – Turns on, or sets the player to standby mode. TOP MENU b Repeat step 1 to complete the entry. C Number buttons (page 26) – Enters the title/chapter numbers, etc. CLEAR – Clears the entry field. D VIDEO FORMAT (page 45) – Changes the video output resolution from the HDMI OUT jack and the COMPONENT VIDEO OUT jacks. Press this button repeatedly if no picture appears. E AUDIO*1 (page 49) – Selects the sound track or the language track on a BD/DVD. c Select “DONE,” and press ENTER to close the on-screen keyboard. POP UP/ MENU RETURN Note PREV You cannot use the extended character set. SLOW/STEP SCAN PLAY PAUSE NEXT SCAN STOP PLAY MODE VOL CH MUTING Number 5, AUDIO, CH+, and H buttons have a tactile dot. Use the tactile dot as a reference when operating the player. 23 24 1-5 *1 When playing MPEG-2 movie files or MP3 music files on a DATA DVD, or a music CD, you cannot select the left or right channel only. SUBTITLE (page 49) – Selects the subtitle language on a BD/DVD. ANGLE – Switches to other viewing angles when available. F Color buttons (RED/GREEN/BLUE/YELLOW) – Short cut keys for selecting items on some BD’s menus (can also be used for BD’s Java interactive operations). G SYSTEM MENU (page 22) – Enters/exits the player’s start menu (“System Menu”). I For TVs operable with the following buttons, see page 17. TOP MENU (page 20) – Opens/closes the BD’s or DVD’s top menu. Center button (ENTER) (page 20, 22) – Enters the selected item. H ./> PREV/NEXT – Skips to the previous/next chapter, track, or file. SLOW/STEP*2 c/ C – Plays in slow motion or stop motion. To return to normal play, press H. • To play in slow motion C during playback. When slow motion Press play starts, press C repeatedly to change the speed : 1/16 t 1/8 t 1/4 t 1/2 of normal playback speed. • To play in stop motion (step by step) C Press X during playback, then press c or repeatedly. 2 m/M SCAN* – Scans backwards or forward. The speed changes when pressed repeatedly. DATA DVD DVD DATA DVD Number buttons CD a During playback, press PLAY MODE repeatedly. 2 4 5 6 7 8 9 3 CLEAR 0 VIDEO FORMAT AUDIO SUBTITLE GREEN a Press DISPLAY. Example: When playing a DVD VIDEO. Play DVD-VIDEO PREV 1-1 2.01.23 Chapters 12 Title Total Repeat Title 2h15m34s POP UP/ MENU RETURN SLOW/STEP SCAN PLAY PAUSE PLAY MODE CD TOP MENU ENTER ◆When playing a video or movie title DATA DVD You can check the title/chapter/track information including video transmission rate etc., by pressing DISPLAY. The information differs depending on the disc type and the player status. ANGLE BLUE YELLOW SYSTEM MENU Available items differ depending on the current title/ track/file or the disc type. To cancel the Play Mode, press PLAY MODE again. For “Time Search,” see “Searching using the remote” (page 26). Items DISPLAY TV/VIDEO 1 RED DVD TV DIMMER Playing in various play mode BD Checking the Disc Information BD OPEN/ CLOSE CH (channel) +/– (page 17) – Selects the TV channels up and down. NEXT SCAN STOP PLAY MODE VOL Details CH MUTING Repeat Chapter (BD-ROM/DVD VIDEO only) Repeats the current chapter. Repeat Title Repeats the current title. The following information appears: 1 Playback status 2 Disc type ◆When playing a music track 3 Title information Items Details Repeat Track Repeats the current track. Repeat All Repeats all the tracks on the disc or the “Music” Title List. *2 Depending on the disc or file type, the function may not work or the scan speeds may differ. Random Plays all the tracks on the disc or the “Music” Title List in a random order. H PLAY – Starts or re-starts playback. ◆When playing a photo image PLAY MODE – Switches to other play modes (Repeat Play, etc.) when pressed during playback. – Searches for a specific point (page 26). DVD You can search by entering the title/chapter number or the time code (elapsed time from the beginning of the disc). Basic Operations </M/m/, (page 20, 22) – Moves the highlight to select a displayed item. BD VOL (volume) +/– (page 17) – Adjusts the TV volume. POP UP/MENU (page 20) – Opens/closes the BD’s pop up menu, or the DVD’s disc menu. RETURN (page 20, 22) – Returns to the previous display. Searching using the remote MUTING (page 17) – Mutes the TV sound. To search for a title or chapter (BD-ROM, DVD VIDEO only) 1 Items Details Repeat All Repeats all the files on the disc or “Photos” Title List. Random Plays all the files on the disc or “Photos” Title List in a random order. 2 Enter the title number using the number buttons while the player is in stop mode. To search for a chapter, enter the chapter number during playback. If you make a mistake, press CLEAR once and re-enter. • Currently playing title number/currently playing chapter number. • Total number of chapters within the title. • Total playback time of the title. 4 Elapsed time of the current title 5 Play mode b Press DISPLAY again. Press ENTER to start playback. Play DVD-VIDEO 1-1 2.01.23 Chapter Time Chapter Total To search for a specific point X PAUSE – Pauses/re-starts playback. x STOP – Stops playback. – Clears the resume point when pressed twice. The resume point for a title is the last point you played, the last track for an audio file, or the last photo for a photo file. 1 During playback, press PLAY MODE repeatedly until “Time Search” appears. 2 Enter the time code using the number buttons. Enter the time in minutes and seconds (e.g., ‘12030’ for 1 hour, 20 minutes and 30 seconds). If you make a mistake, press CLEAR once and re-enter. 3 Press ENTER to start playback. Repeat Title 01.11.56 2h15m34s 10.03 Mbps The display switches to show the following information: 1 Chapter information Note Depending on the DVD VIDEO/BD-ROM/DATA DVD, these search functions may not work. • Elapsed time of the current chapter. • Total playback time of the current chapter. 2 Video transmission rate and the stream information ,continued 26 25 z Hints • You can check disc information also on the front panel display (page 59) or the Title List display (page 22). • You can check the audio information by pressing AUDIO. Adjusting the Pictures Clarifying Low Volume Sounds (Audio DRC) Fine-tuning the picture to your preference Memory1 BD DVD BD DATA DVD DVD White Adjust DATA DVD Black Adjust Hue Audio DRC Off Max Basic Operations Audio Control Color Level The “cinema tuned” picture preset setting will allow you to maximize the visual impact of the BD or DVD you are watching by optimizing the picture settings for different lighting environments. “Memory” allows you to make your own detailed adjustments. Even at low volume, you can make low sounds such as dialogs more audible. Min Max Min Max Green Red Min Max Use [LL][RR] to set the behavior of film source input. Press ENTER to preview. a Select from “Memory 1” to “Memory 3” in step 4 of “Adjusting the Pictures” (page 28). b Select “Detailed Settings,” and press ENTER to turn on the above display. To switch to another “Memory,” press RETURN. Adjusting sound accentual width (dynamic range). This is effective when playback sound is Dolby Digital. Standard Convenient when you cannot turn up the volume (e.g., at night) Detailed Settings b Select “A/V Control,” and press ENTER. ◆ To adjust while previewing the effect Select a setting and press ENTER to switch the display for the setting. Press </, to adjust while checking the effect on the background playback picture. Then press ENTER to save the adjustment. c Select “Video Control,” and press ENTER to Underlined are the default settings for “Memory.” a Press SYSTEM MENU during playback. a Press SYSTEM MENU during playback. b Select “A/V Control,” and press ENTER. c Select “Audio Control,” and press ENTER to turn on the above display. turn on the above display. d While “Audio DRC” is highlighted, select from “Max” to “Off” by pressing </,. d Press </, to select a setting. e Press ENTER. Items Details Brighter Room For a room brighter than normal. Theater Room For a dark room such as a home theater. Standard (default) Normally, select this. Memory (1-3) Select a setting when you want to use the detailed picture adjustments you previously made, or when you want to make a new set. The player remembers up to three sets (see page 28). Note “Audio DRC” is effective only when the disc is a Dolby Digital Blu-ray Disc or DVD, and: – “Dolby Digital” in “Audio Setup” is set to “Downmix PCM” (page 47) and the audio signals are output from the DIGITAL OUT (OPTICAL or COAXIAL) jack or the HDMI OUT jack. – “Audio (HDMI)” in “Audio Setup” is set to “PCM” (page 47) and the audio signals are output from the HDMI OUT jack. – the audio signals are output from the AUDIO OUT (L/R) jacks or the 5.1CH OUTPUT jacks. e Press ENTER. z Hint The above description applies when the picture setting of your TV (if any) is set to ‘Standard.’ Note “Memory” settings do not affect the output from the S VIDEO OUT or VIDEO OUT jacks. 28 27 1-6 c Select each of the picture elements, and adjust using </,. Items Details White Adjust (Min~(mid)~Max) Adjusts the brightness of white colors. Black Adjust (Min~(mid)~Max) Adjusts the richness of dark colors. Hue (Green~(mid)~Red) Balances the green and the red colors. Color Level (Min~(mid)~Max) Adjusts the color saturation. d Press RETURN. Locking a Disc Setting/changing the password BD DVD Setting the Parental Control for DVD VIDEOs Setting the Parental Control for BDROMs DVD BD Setup BD DVD Video Setup Audio Setup Language Parental Control Speakers Options By setting the password and your limit in “Parental Control” Setup, you can control playback of inappropriate discs. Change Password DVD Parental Control BD Parental Control Setup Next Screen Next Screen Next Screen Video Setup Audio Setup Language Parental Control Speakers Options Basic Operations Use to select an item, then press [RR] or ENTER. Confirm SYSTEM MENU Exit Parental Control BD PLAYER Use the number keys to enter the password to turn off the parental lock. Current Level Disc Level a Press SYSTEM MENU. 3 5 The password is required when the DVD exceeds the level you set. Notes • You cannot limit playback if the DVD VIDEO/BD-ROM does not have the “Parental Control” function. • If you forget the password, you will have to return all of the player settings to their factory defaults (page 53). • The above display does not appear for BD-ROM. If you cannot play a BD-ROM because of Parental Control, reset “Change Age Restriction” of “BD Parental Control” (page 50). Setup Change Level Video Setup Audio Setup Language Parental Control Speakers Options Password Level Off Use the number keys to enter the password, and press ENTER. Change Age Restriction Password Age Restriction 255 Use the number keys to enter the password, and press ENTER. Confirm SYSTEM MENU Exit Confirm SYSTEM MENU Exit a Press SYSTEM MENU. a Press SYSTEM MENU. b Select “Setup,” and press ENTER. b Select “Setup,” and press ENTER. c Select “Parental Control,” and press ENTER to turn on the “Parental Control” Setup. c Select “Parental Control,” and press ENTER to turn on the “Parental Control” Setup. d Select “Change Password (Set Password),” and press ENTER. d Select “DVD Parental Control,” and press ENTER. d Select “BD Parental Control,” and press ENTER. e Select “Next Screen,” and press ENTER to turn on the password display. e Select “Change Level,” and press ENTER to turn on the above display. e Select “Change Age Restriction,” and press ENTER to turn on the above display. b Select “Setup,” and press ENTER. c Select “Parental Control,” and press ENTER to turn on the above “Parental Control” Setup. ◆ When you have not yet registered a password Enter a four-digit password using the number buttons, and press m. Re-enter it for confirmation, and press ENTER. This will set the playback limitation level. f Enter the password using the number buttons, and press ENTER. ◆ When you have already registered a password Enter the four-digit password using the number buttons, and press ENTER. Enter a new password and press m, then re-enter it for confirmation, and press ENTER. g Press </, to select the limitation level from “Off” to “Level 8,” and press ENTER. Note that the lower the value, the stricter the limitation. z Hint h When the display returns to the “Parental Control” Setup, select “DVD Parental Control,” and press ENTER. To continue to set “DVD Parental Control,” go to step 4 of “Setting the Parental Control for DVD VIDEOs” (page 30). i Select “DVD Country Code,” and press ENTER. For BD-ROMs, the restriction is set by age, not by level. f Enter the password using the number buttons, and press ENTER. g Press </, to select the age from “0” to “255,” and press ENTER. h When the display returns to the “Parental Control” Setup, select “BD Parental Control,” and press ENTER. i Select “BD Country Code,” and press ENTER. This ensures that you see the scenes intended for your residential area. This ensures that you see the scenes intended for your residential area. j On the “DVD Country Code” display, enter the password using the number buttons, and press ENTER. k Press </, to select your country code (see page 69), or press m and enter the code for your area using the number buttons. l Press ENTER. j On the “BD Country Code” display, enter the password using the number buttons, and press ENTER. k Press </, to select your country code (see page 69), or press m and enter the code for your area using the number buttons. l Press ENTER. z Hint To continue to set “BD Parental Control,” go to step 4 of “Setting the Parental Control for BD-ROMs” (page 30). ,continued 29 30 Viewing All Titles Watching Movie Files DATA DVD The “Movies” Title List first displays all titles on the disc. All Movies Basic Operations Use the “Movies” Title List to browse through and sort MPEG-2 PS movie files on DATA DVDs. All Movies Browse Search Sort 1214 items Spider 1:31 Smoother 1:02 Sideway 1:31 Home 1:25 Alpinist 1:33 Electricity 1:26 Lemon Grove 1:57 Bridget 1:36 Finding Never-Ever Land 1:18 Meet My Mom 1:18 List Select SYSTEM MENU Exit The Browse menu appears when you press < a Press SYSTEM MENU. b Select “Title List,” and press ENTER. c Select “Movies,” and press ENTER. The above “All Movies” display appears, showing all titles (scrollable by pressing m). From “All Movies” you can apply items to all titles using the Browse menu (see below). To use the Browse menu Press < after step 3 to display the items for the “Movies” Title List. For operations, see the pages in parentheses. Available items differ depending on the display. Items Details All Movies Lists all titles (as above). Browse Displays a list of genres, Quicklist, or folders (page 34). Search Searches for a title using the on-screen keyboard (page 34). Sort Reorders the titles by date or alphabet (see below). ◆Example: To apply “Sort” to all titles A Select “Sort,” and press ENTER. B Select the setting you want to sort by; “Recent first,” “Oldest first,” “By title (AtZ),” “By title (ZtA),” and press ENTER. • Viewing All Titles . . . . . . . . . . . . . . . . . . . . . . 32 • Browsing by Genre, Quicklist, or Folder . . . . . 34 • Searching for a Title . . . . . . . . . . . . . . . . . . . . 34 • Programming Playback (Quicklist) . . . . . . . . . 35 32 31 1-7 About the “Movies” (All Movies) Title List display Playing a title a After step 3 of “Viewing All Titles” above, select the title you want to play, and press ENTER or H. All Movies The title starts playing. You can apply other playback settings to the selected title using the “Options” menu (see below). Date : 2006 Genre : Adventure Format : MPEG 1:31 Smoother 1:02 Sideway 1:31 Home 1:25 Alpinist 1:33 Electricity 1:26 Lemon Grove 1:57 Bridget 1:36 Finding Never-Ever Land 1:18 DATA DVD DATA DVD Narrow down the list of titles by selecting the category type (e.g., “Folders”), then the category. You can find the exact title, or titles with a similar name. 1:18 1214 items List Options Spider Smoother Select SYSTEM MENU Exit 1:31 1:02 Play from Beginning 1:31 Add to Quicklist 1:25 Sideway Home Alpinist 1:33 Electricity 1:26 Lemon Grove Folders 1 Detailed information Displays details about the selected title. 1:57 Bridget 1:36 Finding Never-Ever Land Meet My Mom 1:18 • Date: Displays the recording year. • Genre: Displays the genre name. • Format: Displays the coding format. 1:18 List Select SYSTEM MENU Exit The “Options” menu appears when you select a title and press , 2 List area Displays the title names of all content. To use the “Options” menu Watching Movie Files Date : 2006 Genre : Adventure Format : MPEG Searching for a Title 1214 items Spider Meet My Mom All Movies Browsing by Genre, Quicklist, or Folder Search Results 2 items 5 items Winter games 2006 Say No 1:31 Interviews Sea 1:02 Sideway 1:31 Spider 1:25 Stay Alive 1:33 s_ A B C D E F GH I J K L MNO P QR S T U VWX Y Z , . : ; 1 2 3 4 5 6 7 8 9 0 _ ( ) SHFT b Select “Title List,” and press ENTER. Items Details Play from Beginning Starts playing the title you selected from the beginning. d Press < to turn on the Browse menu. Add to Quicklist Adds the selected title to the Quicklist. c Select “Movies,” and press ENTER. e Select “Browse,” and press ENTER. ◆Example: To apply “Play from Beginning” to the selected title f Select the list you want to view from A Select “Play from Beginning,” and press ENTER. “Genres,” “Quicklist,” or “Folders,” and press ENTER. To play in other play mode The list of genres/Quicklist/folders appears as above. For details about the Quicklist, see “Programming Playback (Quicklist)” (page 35). During playback, press PLAY MODE repeatedly. The selected item changes with each press: “Time Search” (page 26) — “Repeat Title” — “Repeat Off” See page 25 for details. g Select the genre/Quicklist/folder you want to CLR CANCEL Select SYSTEM MENU Exit Search results are narrowed down as more characters are entered a Press SYSTEM MENU. Press , instead of ENTER in the above step to display the “Options” menu settings applicable to the title in the given situation. In the above example, the following items are available. SPC DEL DONE Confirm SYSTEM MENU Exit a Press SYSTEM MENU. b Select “Title List,” and press ENTER. c Select “Movies,” and press ENTER. d Press < to turn on the Browse menu. e Select “Search,” and press ENTER to turn on the above display. f Enter the title name using the on-screen keyboard (see page 23). z Hint You can select a title and start playback by pressing H or ENTER, or using the “Options” menu (press ,). view, and press ENTER. z Hint See page 24 for the remote’s operations. z Hint You can select a title and start playback by pressing H or ENTER, or using the “Options” menu (press ,). 34 33 Programming Playback (Quicklist) To remove the title from the “Quicklist” 1 Select the title you want to remove from the displayed “Quicklist,” and press ,. 2 Select “Remove,” and press ENTER. Viewing All Artists Listening to Music Files z Hint You can play the “Quicklist” content in other play modes by pressing PLAY MODE (page 25). DATA DVD Play your favorite titles in the order you like by making your own “Quicklist.” Quicklist The “Quicklist” may be cleared after some operations (e.g., opening the disc tray, or turning off the player etc.). 1:31 Smoother 1:02 Sideway 1:31 Home 1:25 Alpinist 1:33 Electricity 1:26 Lemon Grove 1:57 Bridget 1:36 Finding Never-Ever Land 1:18 Meet My Mom 1:18 List Select SYSTEM MENU Exit The “Quicklist” does not affect the original recording on the disc DATA DVD The “Music” Title List first displays a list of the artist names on the disc. Use the “Music” Title List to browse through and play the MP3 track files on DATA DVDs. You can make a “Quicklist” of your favorites and play in various play modes. 14 items Spider Watching Movie Files Date : 2006 Genre : Adventure Format : MPEG Note Artists 7 items All Artists Angela Simpson 6 Albums Blue Glass 5 Albums Bohemian Beat 6 Albums Cela 4 Albums Classic Remix 5 Albums Commotion 2 Albums Count Dra"Q"la Main Menu 2 Albums Options Play SYSTEM MENU Exit The Browse menu appears when you press < a Press SYSTEM MENU. a Press SYSTEM MENU. b Select “Title List,” and press ENTER. b Select “Title List,” and press ENTER. c Select “Movies,” and press ENTER. c Select “Music,” and press ENTER. The above “Artists” display appears, showing all artist names (scrollable by pressing m). From “Artists” you can apply items to all tracks using the Browse menu (see below). d When the “All Movies” Title List appears, select the title you want to add to the top of the “Quicklist,” and press ,. To use the Browse menu e Select “Add to Quicklist” from the “Options” Press < after step 3 to display the items for the “Music” Title List. For operations, see the pages in parentheses. Available items differ depending on the display. menu, and press ENTER. f Repeat step 4 and 5 to select all the desired titles. Items Select in the order you want to play. You can add the same title multiple times. The “Quicklist” can contain up to 25 titles. All Songs Lists all tracks (page 37). Browse Details Displays a list of artists, albums, genres, Quicklist, or folders (page 38). Search g Press < to turn on the Browse menu. Searches for a track using the on-screen keyboard (page 38). Sort h Select “Browse,” and press ENTER. Reorders the tracks by alphabet, or year, etc. (see below). Now Playing Displays the track information and the playback information during playback. i Select “Quicklist,” and press ENTER to turn ◆Example: To apply “Sort” to all tracks on the above display. A To display the list of tracks, select “All Songs” from the Browse menu and press ENTER. The “Quicklist” Title List appears with the programmed content. B Press < to turn on the Browse menu. j Select the title you want to start playback, C Select “Sort,” and press ENTER. • Viewing All Artists . . . . . . . . . . . . . . . . . . . . . 36 and press ENTER. • Browsing by Artist, Album, Genre, Quicklist, or Folder . . . . . . . . . . . . . . . . . . . . . . . . . . 38 • Searching for a Track . . . . . . . . . . . . . . . . . . . 38 • Programming Playback (Quicklist) . . . . . . . . . 39 35 36 1-8 D Select the setting you want to sort by; “Recent first,” “Oldest first,” “By title (AtZ),” “By title (ZtA),” “By artist (AtZ),” “By artist (ZtA),” and press ENTER. About the “Music” (All Songs) Title List display Playing a track a After step 3 of “Viewing All Artists” above, narrow down the list of tracks by selecting the artist, then the album. All Songs Artist:Deep Artist : DeepGreen Green Album : Splash! Album:Remixes 81-04 Genre:Alternative Genre : Alternative Format:MP3 Format : MP3 To list all tracks, press < and select “All Songs” from the Browse menu. b Select the track you want to play, and press ENTER or H. All Songs Shout in Rio Artist : Deep Green Album : Splash! Genre : Alternative Format : MP3 Home Rash (Spiritual Mix) 5:26 I Feel You (Remix) 4:57 Route 57 (Beatmasters Mix) 9:36 Free (DJ Remix) 6:18 Personal Note 6:18 Main Menu Options To use the “Options” menu Press , instead of ENTER in the above step to display the “Options” menu settings applicable to the track in the given situation. In the above example, the following items are available. Items Details Play Song Starts playing the track you selected from the beginning. Add to Quicklist Adds the selected track to the Quicklist. 6:33 5:26 4:57 Route 57 (Beatmasters Mix) 9:36 Free (DJ Remix) 6:18 Personal Note 6:18 Options Play SYSTEM MENU Exit 2 List area Displays overall content. • Main area: Displays the track names. • Sub area: Displays the total playback time of each track. Play SYSTEM MENU Exit The “Options” menu appears when you select a track and press , 3:55 Rash (Spiritual Mix) I Feel You (Remix) • Artist: Displays the artist name. • Album: Displays the album name. • Genre: Displays the genre name. • Format: Displays the coding format. 9:31 6:33 7:31 Strangled About unplayable audio track files Searching for a Track DATA DVD DATA DVD Narrow down the list of tracks by selecting the category type (e.g., “Genres”), then the category. You can find the exact track, or tracks with a similar name. Genres Play Song 8:00 7:31 Add to Quicklist 3:55 Strangled 8:00 Shout in Rio Home Search Results 20 items All Genres Alternative 2876 Songs Blues 195 Songs Books And Spoken Listening to Music Files Policies of Truth 9:31 Policies of Truth 1 Detailed information Displays details about the selected track. 1214 items Never Let Me Down (Split Mix) Options Never Let Me Down (Split Mix) Main Menu The title starts playing. You can apply other playback settings to the selected track using the “Options” menu (see below). Browsing by Artist, Album, Genre, Quicklist, or Folder 1214 items 16 Songs Celtic 304 Songs Classical 841 Songs Comedy R A B C D E F GH I J K L MNO P QR S T U VWX Y Z , . : ; 1 2 3 4 5 6 7 8 9 0 _ ( ) 32 Songs Country 2 Songs Dance 460 Songs Dark 60 Songs SHFT Main Menu Options DONE Play SYSTEM MENU Exit b Select “Title List,” and press ENTER. The player does not play the file if: – The DATA DVD is not recorded in an MP3 format that conforms to UDF (Universal Disk Format). – The audio track file does not have the extension “.MP3.” – The data is not formatted properly even though it has the extension “.MP3.” – The data is not MPEG-1 Audio Layer III data. – The data is recorded in mp3PRO format. – The file name contains characters other than numbers and English alphabet. c Select “Music,” and press ENTER. d Press < to turn on the Browse menu. e Select “Browse,” and press ENTER. f Select the list you want to view from “Artists,” “Albums,” “Genres,” “Quicklist” or “Folders,” and press ENTER. The list of artists/albums/genres/Quicklist/folders appears as above. For details about the Quicklist, see “Programming Playback (Quicklist)” (page 39). ◆Example: To apply “Play Song” to the selected track A Select “Play Song,” and press ENTER. To play in other play mode folder you want to view, and press ENTER. z Hint You can select a track from the list of tracks, and start playback by pressing ENTER or H, or using the “Options” menu (press ,). z Hints • See page 24 for the remote’s operations. • Even after stopping playback, the player resumes playback from the last track you played. • Depending on the writing software used, the displayed track or album names may be different from the characters you input. 8:00 7:31 Ree 7:32 Rise 6:33 Rose Bed 6:34 Rule the World 6:35 CLR CANCEL Select SYSTEM MENU Exit a Press SYSTEM MENU. b Select “Title List,” and press ENTER. c Select “Music,” and press ENTER. d Press < to turn on the Browse menu. e Select “All Songs,” and press ENTER. f Press < to turn on the Browse menu. g Select “Search,” and press ENTER to turn on the above display. h Enter the track name using the on-screen keyboard (see page 23). g Select the artist/album/genre/Quicklist/ During playback, press PLAY MODE repeatedly. The selected item changes with each press: “Repeat Track” — “Repeat All” — “Random” — “Repeat Off” See page 25 for details. 9:31 Raging Plants Ragamufin Search results are narrowed down as more characters are entered Genres without content do not appear in the list a Press SYSTEM MENU. SPC DEL 7 items Raga z Hints • You can select a track from the search result, and start playback by pressing ENTER or H, or using the “Options” menu (press ,). • You can search for a genre, artist, album, or folder name from each Title List (e.g., “Genres”). Notes • Playback time of MP3 audio tracks may not be displayed correctly. • If you put an extension “.MP3” to a non-MP3 file, the file may accidentally play on the player. Note that such output may cause the connected device to malfunction. • Playback may not start immediately after skipping to another album. • When using the Resume function on MP3 tracks, playback starts from the beginning of the track. 37 Programming Playback (Quicklist) 38 To remove the title from the “Quicklist” 1 Select the track you want to remove from the displayed “Quicklist,” and press ,. 2 Select “Remove,” and press ENTER. Viewing All Folders Viewing Photo Files z Hint You can play the “Quicklist” content in other play modes by pressing PLAY MODE (page 25). DATA DVD Play your favorite tracks in the order you like by making your own “Quicklist.” Note The “Quicklist” may be cleared after some operations (e.g., opening the disc tray, or turning off the player etc.). Quicklist Never Let Me Down (Split Mix) 9:31 8:00 Shout in Rio 7:31 Options Play SYSTEM MENU Exit The “Quicklist” does not affect the original recording on the disc a Press SYSTEM MENU. b Select “Title List,” and press ENTER. Listening to Music Files Artist : Deep Green Album : Splash! Genre : Alternative Format : MP3 Main Menu Use the “Photos” Title List to view the JPEG images on DATA DVDs. You can reorder the files and start playing a slideshow. 3 items Policies of Truth DATA DVD The “Photos” Title List first displays all the folders on the disc. Folders 2 items Kurobe-dam 2005 Jungfraujoch 2006 Confirm SYSTEM MENU Exit The Browse menu appears when you press < while on the leftmost row a Press SYSTEM MENU. b Select “Title List,” and press ENTER. c Select “Photos,” and press ENTER. c Select “Music,” and press ENTER. The above “Folders” display appears, showing all folders (scrollable by pressing m). From “Folders” you can apply items to all files using the Browse menu (see below). d Press < to turn on the Browse menu. e Select “All Songs,” and press ENTER. To use the Browse menu f When the “All Songs” Title List appears, Press < after step 3 to display the items for “Photos” Title List. For operations, see the pages in parentheses. Available items differ depending on the display. select the track you want to add to the top of the “Quicklist,” and press ,. g Select “Add to Quicklist” from the “Options” Items Details All Photos Displays all files in alphabetical order (page 41). menu, and press ENTER. h Repeat step 6 and 7 to select all the desired tracks. Select in the order you want to play. You can add the same track multiple times. The “Quicklist” can contain up to 25 tracks. Browse Displays a list of dates, Quicklist, or folders (page 42). Search Searches for a file using the on-screen keyboard (page 42). Sort Reorders the files by date or alphabet (see below). ◆Example: To apply “Sort” to all files i Press < to turn on the Browse menu. A To display the list of all files, select “All Photos” from the Browse menu and press ENTER. j Select “Browse,” and press ENTER. B Move the highlight to the left most row, and press < to turn on the Browse menu. k Select “Quicklist,” and press ENTER to turn C Select “Sort,” and press ENTER. on the above display. • Viewing All Folders . . . . . . . . . . . . . . . . . . . . . 40 The “Quicklist” Title List appears with the programmed content. • Browsing by Date, Quicklist, or Folder . . . . . . 42 • Searching for a Photo. . . . . . . . . . . . . . . . . . . 42 l Select the track you want to start playback, • Programming a Slideshow Playback (Quicklist) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 and press ENTER. 40 39 1-9 D Select the setting you want to sort by; “Recent first,” “Oldest first,” “By title (AtZ),” “By title (ZtA),” and press ENTER. About the “Photos” (All Photos) Title List display Playing a slideshow a After step 3 of “Viewing All Folders” above, press < and select “All Photos” from the Browse menu. All Photos Browsing by Date, Quicklist, or Folder 1214 items File : DSC00434.jpg File:Summer of '06.jpg Date:July/23/2006 Date : 7/23/2006 Resolution:196x298 Resolution: 293 x 196 pixels Format:JPEG Format: JPEG b Select the file you want to start from, and press ENTER to turn on the “Options” menu. Searching for a Photo DATA DVD DATA DVD Narrow down the list of files by selecting the category type (e.g., “Date”), then the category. You can find the exact file, or files with a similar name. Confirm SYSTEM MENU Exit c Select “Slideshow,” and press ENTER. Year Slideshow starts. You can apply other playback settings to the selected file using the “Options” menu (see below). All Photos Slideshow Add to Quicklist File : DSC00434.jpg Date : 7/23/2006 Resolution: 293 x 196 Format: JPEG 2 List area Displays overall photo content in thumbnail. Confirm SYSTEM MENU Exit To use the “Options” menu Available “Options” menu settings differ depending on the situation. In the above example of the use of the “Options” menu, the following items are available. Items Details Slideshow Starts playing a slideshow as above. Add to Quicklist Adds the selected file to the Quicklist for later slideshow playback. To play in other play mode During playback, press PLAY MODE repeatedly. The selected item changes with each press: “Repeat All” — “Random” — “Repeat Off” See page 25 for details. 7 items 2006 About unplayable photo files The player does not play the file if: – The DATA DVD is not recorded in a JPEG format that conforms to UDF (Universal Disk Format). – The photo file is not recorded in a format that conforms to the DCF*. – The file has an extension other than “.JPEG.” – The image is larger than 4,096 (width) × 4,096 (height) in normal mode, or progressive JPEG. – The image does not fit the screen (the image is reduced). – The file name contains characters other than numbers and English alphabet. • Even when the above are not applicable, some files may not play depending on the recording condition or the method (e.g., writer software). • Files may not play on this player if edited on a PC. 2005 File:Summer of '06.jpg Date:July/23/2006 Resolution:196x298 pixels Format:JPEG 2004 2003 R_ 2002 A B C D E F GH I J K L MNO P QR S T U VWX Y Z , . : ; 1 2 3 4 5 6 7 8 9 0 _ ( ) 2001 2000 1999 1998 Viewing Photo Files • File: Displays the file name. • Date: Displays the shooting date. • Resolution: Displays the picture resolution in width × height. • Format: Displays the recording format. 1214 items Options The “Options” menu appears when you select a file and press ENTER Search Results 10 items 2007 1 Detailed information Displays details about the selected file. SHFT a Press SYSTEM MENU. b Select “Title List,” and press ENTER. c Select “Photos,” and press ENTER. d Press < to turn on the Browse menu. e Select “Browse,” and press ENTER. f Select the list you want to view from “Date,” “Quicklist,” or “Folders” and press ENTER. The list of date/Quicklist/folders appears as above. For details about the Quicklist, see “Programming a Slideshow Playback (Quicklist)” (page 43). * “Design rule for Camera File system”: Image standards for digital cameras regulated by JEITA (Japan Electronics and Information Technology Industries Association). g Select the date/Quicklist/folder you want to view, and press ENTER. You can select a file and start slideshow by using “Options” menu (press ,). • See page 24 for the remote’s operations. • Even after stopping playback, the player resumes playback from the last file you played. CLR CANCEL Select SYSTEM MENU Exit Search results are narrowed down as more characters are entered a Press SYSTEM MENU. b Select “Title List,” and press ENTER. c Select “Photos,” and press ENTER. d Press < to turn on the Browse menu. e Select “All Photos,” and press ENTER. f Move the highlight to the leftmost row, and press < to turn on the Browse menu. g Select “Search,” and press ENTER to turn on the above display. h Enter the file name using the on-screen keyboard (see page 23). z Hint z Hints SPC DEL DONE Confirm SYSTEM MENU Exit z Hint You can select a file and start slideshow by using “Options” menu (press ,). Note The photos may appear slowly depending on the size and the number of files. 42 41 Programming a Slideshow Playback (Quicklist) m Select “Slideshow” from the “Options” Using the Setup Displays menu, and press ENTER. To remove from the “Quicklist” DATA DVD Play a slideshow in the order you like by making your own “Quicklist.” Quicklist 1 Select the file you want to remove from the displayed “Quicklist,” and press ENTER. 2 Select “Remove,” and press ENTER. Changing the Initial Settings z Hint You can play the “Quicklist” content in other play modes by pressing PLAY MODE (page 25). Select “Setup” from the “System Menu” when you need to change the settings of the player (e.g., when changing the connected device or the audio/video output, etc.). The last part of this section explains how to return all of these settings to their factory defaults. 22 items Note The “Quicklist” may be cleared after some operations (e.g., opening the disc tray, or turning off the player etc.). File : DSC00434.jpg Date : 7/23/2006 Resolution: 293 x 196 Format: JPEG a Press SYSTEM MENU. b Select “Title List,” and press ENTER. Viewing Photo Files Confirm SYSTEM MENU Exit The “Quicklist” does not affect the original recording on the disc BD DVD CD Setup Video Setup Audio Setup Language Parental Control Speakers Options TV Type 4:3 Video Out DVD Aspect Ratio YCbCr/RGBPC(HDMI) 24p Output 16:9 Normal Letter Box Y, Cb, Cr Off Use to select an item, then press [RR] or ENTER. Confirm SYSTEM MENU Exit Note Playback settings described in this section may not work when there is any preset playback setting in the disc. The disc’s playback settings take priority over the player’s playback settings. DATA DVD From the “System Menu,” enter the “Setup” displays to change the settings of the player. a Press SYSTEM MENU while the player is stopped. b Select “Setup,” and press ENTER. c Select the “Setup” display you want to use, c Select “Photos,” and press ENTER. from “Video Setup,” “Audio Setup,” “Language,” “Parental Control,” “Speakers,” or “Options,” and press ENTER. d Press < to turn on the Browse menu. e Select “All Photos,” and press ENTER. The “Setup” display appears with the related items. Note that the display switches to the screen saver if you do not operate for 15 minutes. f When the “All Photos” Title List appears, select the file you want to add to the top of the “Quicklist,” and press ENTER. d Select the item you want to change, and press ENTER. Refer to the explanations in the following sections. g Select “Add to Quicklist” from the “Options” menu, and press ENTER. To return to the previous display h Repeat step 6 and 7 to select all the desired Press RETURN. files. Select in the order you want to play. You can add the same file multiple times. The “Quicklist” can contain up to 25 files. i Move the highlight to the leftmost row, and press < to turn on the Browse menu. • Using the Setup Displays . . . . . . . . . . . . . . . . 44 • Video Setup . . . . . . . . . . . . . . . . . . . . . . . . . . 45 j Select “Browse,” and press ENTER. • Audio Setup . . . . . . . . . . . . . . . . . . . . . . . . . . 47 k Select “Quicklist,” and press ENTER to turn • Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 on the above display. • Parental Control . . . . . . . . . . . . . . . . . . . . . . . 50 The “Quicklist” Title List appears with the programmed content. • Speakers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 • Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 l Select the file you want to start playback, and • Resetting the Player . . . . . . . . . . . . . . . . . . . . 53 press ENTER. 43 44 1-10 To set the video output resolution Video Setup Press VIDEO FORMAT repeatedly to select the desired resolution. Note that the resolution differs depending on the display device, connecting jack and the source material as below. Underlined items are the default settings. TV Type – Select your TV type. 4:3 – 4:3 screen TV. 16:9 – Wide-screen TV, or a TV with a wide mode function. 4:3 Video Out – Select the display configuration for a 4:3 screen picture on a 16:9 wide screen TV. Full – Displays a 4:3 screen picture in 16:9 aspect ratio. HDMI OUT COMPONENT VIDEO OUT VIDEO/S VIDEO Automatically selects the recommended resolution acceptable for your TV. 480i 480i 480i 480i 480i 480p 480p 480i 720p 720p BD:720p, DVD:480p*3 480i 1080i 1080i BD:1080i, DVD:480p*3 480i 1080p 1080p 480i 480i Source Direct Output differs depending on source material*1 Output differs depending on source material*2 480i * Outputs in the same resolution and frequency as recorded on the disc. *2 1080/24p video signals are not output from the COMPONENT VIDEO OUT jacks. *3 Outputs in the resolution of the original setting (720p or 1080i) when the DVD is not copy guarded. Normal – Displays a 4:3 screen picture in 4:3 aspect ratio with black bands on the sides. Select this if your TV does not have a 4:3 screen mode. Notes • If the picture is not clear, natural or to your satisfaction, try another resolution that suits the disc and your TV/projector, etc. For the details, refer also to the instruction manual supplied with the TV/projector, etc. • 480i or 480p video signals may be output when you connect to the COMPONENT VIDEO OUT jacks and play some copy-guarded BDs/DVDs. To enjoy the HD quality resolution in this case, connect the display device to the HDMI OUT jack using an HDMI cord. • Even when you select a setting other than “Auto,” the player automatically adjusts the video signals if the TV cannot accept the set resolution. Changing the Initial Settings – Select the type of output from the HDMI OUT jack. 480i 480p 1 DVD Aspect Ratio Letter Box – Select the display configuration for a 16:9 – Displays a wide picture with black bands on the top and DVD picture on a 4:3 screen TV (selectable bottom. when “TV Type” is set to “4:3”). Note that the aspect ratio is fixed on some Pan & Scan discs. For example, a 4:3 letterbox picture – Displays a full-height picture on the entire screen, with trimmed sides. may appear even when “Pan & Scan” is selected. YCbCr / RGBPC (HDMI) Connecting jack Auto Settings Y, Cb, Cr – Select this when connecting to an HDMI device. RGB (16-235) – Select this when connecting to a device with an HDCP-compliant DVI jack. RGB (0-255) – Select this when connecting to an RGB (0-255) device. To output the 1080/24p video signals A 1080/24p-compatible TV is required for this setting. 1 2 Set “24p Output” in “Video Setup” to “On” (page 45). Press VIDEO FORMAT repeatedly to select “Auto” or “Source Direct.” Note If there is no picture, press VIDEO FORMAT repeatedly until the picture appears correctly. 24p Output On – For connection to a 1080/24p-compatible TV – Sends 1920 × 1080p/24 Hz video signals when playing Film-based materials on BDROMs (720p/24 Hz or 1080p/24 Hz). Select this when the connection applies. using the HDMI OUT jack. Off – Select this for any other connection. Note “TV Type” and “DVD Aspect Ratio” can be set when video output resolution is 480i/480p. ,continued 46 45 About the audio output signals Audio Setup The audio output differs as follows, depending on the source, output jack, and the selected settings. Jacks/ settings Disc/source BDLinear PCM 2ch ROM Underlined items are the default settings. Since many factors affect the type of audio output, see also “About the audio output signals” on page 48. Dolby Digital Dolby Digital – Select the audio signals output when playing – Select this when connecting to a device with a built-in Dolby Digital decoder. Dolby Digital discs. This setting affects the Downmix PCM output from the DIGITAL OUT (COAXIAL – Converts to output Linear PCM signals. Select this when connecting to a device or OPTICAL) jack. without a built-in Dolby Digital decoder. DIGITAL OUT (OPTICAL/ COAXIAL) jacks*2 HDMI OUT jack*3 2ch 5.1ch PCM Bitstream PCM*4 2ch 2ch 2ch LPCM 2ch LPCM 2ch LPCM 2ch LPCM 2ch Downmix LPCM 2ch Downmix LPCM 2ch Downmix LPCM 2ch Downmix LPCM 5.1ch LPCM 5.1ch LPCM 5.1ch*5 2ch Downmix 5.1ch 7.1ch DTS Downmix – Select the type of 2-channel signals when down-mixed from multi-channel DTS sources (effective for audio connections when “DTS” is set to “Downmix PCM”). Audio (HDMI) – Select the output method from the HDMI OUT jack. Stereo – Downmixes multi-channel audio signals for two channel stereo. Lt/Rt – Allows you to hear surround sound when the connected device has a built-in Dolby Pro Logic decoder. Auto – Normally, select this. Outputs audio signals according to the status of the connected HDMI device. PCM – Converts all audio signals to Linear PCM. DVD CD Auto*4 2ch Downmix 5.1ch Downmix 7.1ch LPCM 7.1ch LPCM Dolby Digital 2ch Downmix 5.1ch 2ch Downmix LPCM Dolby Digital 5.1ch LPCM Dolby Digital Dolby Digital Plus 2ch Downmix 5.1ch 2ch Downmix LPCM Dolby Digital 7.1ch LPCM*6 Dolby Digital Dolby TrueHD 2ch Downmix 5.1ch Dolby Digital 5.1ch LPCM Dolby Digital DTS 2ch Downmix 5.1ch DTS 5.1ch LPCM DTS DTS-HD 2ch Downmix 5.1ch DTS 5.1ch LPCM DTS Linear PCM 2ch 2ch 2ch LPCM 2ch LPCM 2ch LPCM Dolby Digital 2ch Downmix 5.1ch Dolby Digital 5.1ch LPCM Dolby Digital DTS 2ch Downmix 5.1ch DTS 5.1ch LPCM DTS MPEG 2ch 2ch 2ch LPCM — 2ch LPCM 2ch LPCM Linear PCM 2ch 2ch 2ch 2ch LPCM 2ch LPCM 2ch LPCM 2ch LPCM DTS 2ch Downmix 5.1ch 2ch Downmix LPCM DTS 5.1ch LPCM DTS DTS Changing the Initial Settings DTS – Select the audio signals output when playing – Select this when connecting to a device with a built-in DTS decoder. DTS discs. This setting affects the output Downmix PCM from the DIGITAL OUT (COAXIAL or – Converts to output Linear PCM signals. Select this when connecting to a device OPTICAL) jack. without a built-in DTS decoder. AUDIO OUT L/R jacks*1 2ch Downmix LPCM 2ch Downmix LPCM 2ch Downmix LPCM 2ch LPCM 2ch Downmix LPCM 2ch Downmix LPCM *1 “2 Channel” and “5.1 Channel” are selectable under “Audio Output Mode” in “Speakers” Setup (page 51). *2 PCM : when “Dolby Digital” or “DTS” in “Audio Setup” is set to “Downmix PCM” (page 47). Bitstream : when “Dolby Digital” or “DTS” in “Audio Setup” is set to “Dolby Digital” or “DTS” (page 47). *3 Selectable under “Audio (HDMI)” in “Audio Setup” (page 47). *4 Selectable under “Audio (HDMI)” in “Audio Setup” (page 47). Resulting output may differ depending on the connected HDMI device. *5 When the sampling frequency is 192 kHz, the player downmixes to 2ch signals even if the disc or source is 5.1ch. *6 Outputs 7.1ch LPCM signals decoded from Dolby Digital Plus audio stream. ,continued 48 47 1-11 Language Parental Control Underlined items are the default settings. This function limits playback of DVD VIDEOs and BD-ROMs. To activate, see “Locking a Disc” (page 29). The default settings are underlined. Notes • When you select a language in “Audio,” “Subtitles,” “BD/DVD Menu” that is not recorded on the disc, one of the recorded languages is automatically selected. • Playback settings stored in the disc take priority over these settings. Notes • You cannot limit playback if the disc does not have the Parental Control function. • If you forget the password for “Parental Control,” you will need to reset the player (page 53). Note that all the settings you made also return to their defaults. OSD English – Select your language for the player on-screen – Displays the menus and messages in English. displays. Français – Displays the menus and messages in French. Audio – Select the default soundtrack language for BD-ROMs/DVD VIDEOs. English – Plays the soundtrack in English. Other – See “Language Code List” on page 68 and enter the code for your language. Subtitles English – Select the default subtitle language for BD- – Displays the subtitles in English. ROMs/DVD VIDEOs. French – Displays the subtitles in French. Other – See “Language Code List” on page 68 and enter the code for your language. BD/DVD Menu – Select the default menu language for BDROMs/DVD VIDEOs. w/Subtitle – Displays BD’s/DVD’s menus in the same language as the subtitle language. Changing the Initial Settings French – Plays the soundtrack in French. Change Password (Set Password) Next Screen – Set or change the password for the “Parental Control” function. You will be asked for the password when playing restricted discs or when changing the control level. DVD Parental Control Change Level – Set the control level. The display asks for the password if the disc’s pre-determined level exceeds the limit you set. The default setting is “Off.” DVD Country Code – This ensures that you see the scenes intended for your residential area. BD Parental Control Change Age Restriction – Set the control level. The display asks for the password if the disc’s pre-determined age restriction is higher than the age you set. The default setting is “255.” BD Country Code – This ensures that you see the scenes intended for your residential area when playing BD-ROMs. English – Displays BD’s/DVD’s menus in English. French – Displays BD’s/DVD’s menus in French. Other – See “Language Code List” on page 68 and enter the code for your language. Subtitle Display On – Turns on the subtitles. Off – Turns off the subtitles. 49 50 Speakers Options The following items are necessary when using the 5.1CH OUTPUT jacks. The default settings are underlined. Audio Output Mode – For analog connection. Speaker Setup 2 Channel – Select this when connecting to an AV amplifier (receiver) using the AUDIO OUT (L/ R) jacks. On Screen Display On – Select whether to display the playback status – Displays playback status. on the screen (Stop, Play, etc.). Off – Playback status is not displayed. 5.1 Channel – Select this when connecting to an AV amplifier (receiver) using the 5.1CH OUTPUT jacks. – Select whether to activate the “Auto Power Off” function of the player. Next Screen 1 Select the speaker setting that needs adjusting by pressing M/m. • “C” (center speaker): “Yes” or “No” • “Ls/Rs” (left surround speaker/right surround speaker): “Yes” or “No” • “L/R” (left front speaker/right front speaker): “Large” or “Small” 2 Adjust the setting by pressing </,. • For “C” and “Ls/Rs,” select whether the speakers are included in your system. • For “L/R,” select the size. This setting is disabled if either of “C” or “Ls/Rs” is set to “No.” 3 Press ENTER to save the adjustments. Auto Power Off Easy Setup Changing the Initial Settings – This setting affects the output from the 5.1CH OUTPUT jacks. Underlined items are the default settings. – Re-runs the Easy Setup to make the basic settings. On – Turns off the player when the player is left in stop or pause mode without operation for 30 minutes. Off – The player remains turned on with or without operation. Start – Press ENTER and see page 18. HDMI Control On – Select whether to activate the HDMI Control – Activates the function. Off function of the player (page 11). – Turns off the function. Hybrid Disc Playback Layer – Select the layer priority when playing a Hybrid Disc. Remove the disc when you change the setting. 51 52 1-12 BD – Plays BD layer. DVD – Plays DVD layer. CD – Plays CD layer. Troubleshooting Resetting the Player Additional Information You can return all of the player settings to their factory defaults. @/1 x HDMI HD If you experience any of the following difficulties while using the player, use this troubleshooting guide to help remedy the problem before requesting repairs. Should any problem persist, consult your nearest Sony dealer (For customers in the USA only). FL OFF Power a When the power is on, hold down x on the The power does not turn on. , Check that the power cord is connected securely. , It takes a short while before the player turns on. front panel, and press @/1. The player turns off, and all of the settings return to their factory defaults. Changing the Initial Settings Picture There is no picture/picture noise appears. • Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . 54 • Self-Diagnosis Function . . . . . . . . . . . . . . . . . 57 , Re-connect the connecting cord securely. , The connecting cords are damaged. , Check the connection to your TV (page 10) and switch the input selector on your TV so that the signal from the player appears on the TV screen. , The disc is dirty or flawed. , If the picture output from your player goes through your VCR to get to your TV or if you are connected to a combination TV/VIDEO player, the copy-protection signal applied to some BD/DVD programs could affect picture quality. If you still experience problems even when you connect your player directly to your TV, try connecting your player to your TV’s S VIDEO input (page 10). , The player is connected to an input device that is not HDCPcompliant (the HDMI indicator on the front panel does not light up). See page 11. , If the HDMI OUT jack or the COMPONENT VIDEO OUT jacks are used for video output, changing the output resolution may solve the problem (page 46). Press VIDEO FORMAT repeatedly until the picture appears correctly. , Depending on the disc, the picture quality may be poor when the VIDEO FORMAT setting is set to other than “480i,” even when the player is connected to a progressive or HD TV using a component cord or an HDMI cord. If this happens, press VIDEO FORMAT repeatedly to switch to “480i.” , When playing a double-layer DVD, the video and audio may be momentarily interrupted at the point where the layers switch. • Index to Parts and Controls . . . . . . . . . . . . . . 58 • GNU License Information . . . . . . . . . . . . . . . . 60 • Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 • Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 67 • Language Code List . . . . . . . . . . . . . . . . . . . . 68 • Parental Control Country/Area Code List . . . . 69 • Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 , The aspect ratio of the disc is fixed on your BD/DVD. See page 45. The dark area of the picture is too dark/the bright area is too bright or unnatural. , Set “Video Control” in “A/V Control” to “Standard” (default) (page 28). , Adjust each picture setting for “Memory” in “Video Control” to midpoint (default) (page 28). Sound There is no sound. The sound is not output correctly. , Check the “Audio Output Mode” in “Speakers” Setup (page 51) if the AUDIO OUT (L/R) jacks or the 5.1CH OUTPUT jacks are used for audio connection. , The disc is skewed. , The player cannot play certain discs (page 6). , The region code on the BD/DVD does not match the player. , Moisture has condensed inside the player (page 3). , The player cannot play a recorded disc that is not correctly finalized (page 6). , The movie file size exceeds 2 GB. , The file on the DATA DVD contains characters other than numbers and English alphabet. Some functions such as Stop, Search, Slowmotion Play, Repeat Play, or Random Play cannot be performed. , Depending on the disc, you may not be able to do some of the operations above. Refer to the operating manual that comes with the disc. The language for the soundtrack cannot be changed. The MP3 audio track file cannot be played (page 36). , Try using the BD’s or DVD’s menu instead of the direct selection button on the remote (page 21). , Multi-lingual tracks are not recorded on the BD/DVD being played. , The BD/DVD prohibits the changing of the language for the sound track. , The DATA DVD is not recorded in the MP3 format that conforms to UDF (Universal Disk Format). , The audio track file does not have the extension “.MP3.” , The data is not formatted properly even though it has the extension “.MP3.” , The data is not MPEG-1 Audio Layer III data. , The player cannot play audio tracks in mp3PRO format. , Characters other than numbers and English alphabet are contained in the file name. The subtitle language cannot be changed or turned off. , Try using the BD’s or DVD’s menu instead of the direct selection button on the remote (page 21). , Multi-lingual subtitles are not recorded on the BD/DVD being played. , The BD/DVD prohibits the changing of subtitles. The photo file cannot be played (page 40). , The disc is dirty or flawed. , The DATA DVD is not recorded in a JPEG format that conforms to UDF (Universal Disk Format). , The file has an extension other than “.JPEG” or “.JPG.” , The image is larger than 4,096 (width) × 4,096 (height) in normal mode. (Some progressive JPEG files cannot be displayed even if the file size is within this specified capacity.) , The image does not fit the screen (the image is reduced). , The photo file format does not conform to DCF* (page 41). , Characters other than numbers and English alphabet are contained in the file name. Additional Information , The disc is dirty or flawed. , Re-connect the connecting cord securely. , The connecting cord is damaged. , The player is connected to the wrong input jack on the amplifier (receiver) (page 12). , The amplifier (receiver) input is not correctly set. , The player is in pause mode or in Slow-motion Play mode. , The player is in scan mode. , If the audio signal does not come through the DIGITAL OUT (OPTICAL or COAXIAL)/HDMI OUT jack, check the audio settings (page 47). , The equipment connected to the HDMI OUT jack does not conform to the audio signal format, in this case set “Audio (HDMI)” in “Audio Setup” to “PCM” (page 47). The angles cannot be changed. , Try using the BD’s or DVD’s menu instead of the direct selection button on the remote (page 21). , Multi-angles are not recorded on the BD/DVD being played. , The BD/DVD prohibits changing of the angles. The HDMI Control function does not work. , If the HDMI indicator on the front panel does not light up, check the HDMI connection (page 11, 15). , Set “HDMI Control” to “On” (page 52). , Make sure that the connected component is compatible with the HDMI Control function. Refer to the operating instructions of the component for details. , Check that the power cord of the connected component is connected securely. , Check the connected component’s setting for the HDMI Control function. Refer to the operating instructions of the component. , If you change the HDMI connection, connect and disconnect the power cord, or if power failure occurs, set “HDMI Control” to “Off,” then set “HDMI Control” to “On” (page 52). , For details on the HDMI Control function, see “About the ‘BRAVIA’ Theatre Sync features (for HDMI connections only)” (page 11). * “Design rule for Camera File system”: Image standards for digital cameras regulated by JEITA (Japan Electronics and Information Technology Industries Association). The file name is not correctly displayed. No sound is output from the HDMI OUT jack , Try the following: 1Turn the player off and on again. 2Turn the connected equipment off and on again. 3Disconnect and then reconnect the HDMI cord. , The HDMI OUT jack is connected to a DVI device (DVI jacks do not accept audio signals). The sound volume is low. , The sound volume is low on some BDs/DVDs. The sound volume may improve if you adjust the “Audio Control” setting in “A/V Control” (page 27). , The player can only display numbers and alphabet. Other characters may be displayed differently. , Depending on the writing software used, the input characters may be displayed differently. The disc does not start playing from the beginning. , Random Play or Repeat Play is selected (page 25). , Resume play mode is on (page 20). The player starts playing the disc automatically. The display language on the screen switches automatically. , The disc features an auto playback function. Operation The remote does not function. , The batteries in the remote are weak (page 16). , There are obstacles between the remote and the player. , The distance between the remote and the player is too far. , The remote is not pointed at the remote sensor on the player. , When “HDMI Control” is set to “On” (page 52), the display language on the screen automatically switches according to the language setting of the connected TV (if you change the setting on your TV, etc). Playback stops automatically. , While playing discs with an auto pause signal, the player stops playback at the auto pause signal. The player does not operate properly. , When static electricity, etc., causes the player to operate abnormally, unplug the player. The disc does not play. , The disc is turned over. Insert the disc with the playback side facing down. , Try the following: 1Turn the player off and on again. 2Turn the connected equipment off and on again. 3Disconnect and then connect the HDMI cord again. , If the HDMI OUT jack is used for video output, changing the video output resolution may solve the problem (page 46). Press VIDEO FORMAT repeatedly until the picture appears correctly. 54 53 The picture does not fill the screen, even though the aspect ratio is set in “TV Type” under “Video Setup.” There is no picture or picture noise appears when connected to the HDMI OUT jack. ,continued 55 56 1-13 The disc tray does not open and “LOCK” appears on the front panel display. , Contact your Sony dealer or local authorized Sony service facility. The disc tray does not open and you cannot remove the disc even after you press Z. , Turn on the player. As soon as “POWER ON” appears on the front panel display, press x on the player (not the remote) repeatedly until the tray opens. Repeat the above procedure several times if the tray does not open on the first try. “UNPLAYABLE” appears when playing a DATA DVD. , See also “The photo file cannot be played” or “The MP3 audio track file cannot be played” (page 55). , The MP3 audio track/JPEG image file you want to play/view is damaged. , The data is not MPEG-1 Audio Layer III data. , The JPEG image file format does not conform to DCF* (page 41). , The JPEG image file has the extension “.JPG” or “.JPEG,” but is not in JPEG format. * “Design rule for Camera File system”: Image standards for digital cameras regulated by JEITA (Japan Electronics and Information Technology Industries Association). The player does not accept any button. , Hold down \/1 on the player for more than five seconds until the indicators on the front panel display turn off. Index to Parts and Controls Self-Diagnosis Function Buttons on the remote and the player have the same function if they have the same or similar name. For details, see the pages in parentheses. When the self-diagnosis function is activated to prevent the player from malfunctioning, the “ERR” error code appears on the front panel display indicating the cause. Error code Cause and/or corrective action AACS ERR AACS read failure. tRemove the protected disc. LSI1 ERR LSI2 ERR LSI3 ERR MEM ERR FLASH ERR ROM ERR tContact your nearest Sony dealer or local authorized Sony service facility and give the error code. Front panel HDMI Additional Information A @/1 (20) – Turns on the player, or sets to standby mode. B Disc tray (20) C H, X, x (20) – Starts, pauses, or stops playback. D ./> (24) – Skips to the previous/next chapter or track. – Scans forward or backwards when held down. E A (20) – Opens or closes the disc tray. HD FL OFF F HDMI indicator (11) – Lights up when an HDMI device is connected. HD indicator (11) – Lights up when outputting 720p/1080i/1080p video signals. FL OFF indicator (24) – Lights up when the front panel display and other indicators on the front panel are turned off. G Remote sensor (16) H Blu-ray Disc indicator – Lights up when a BD is recognized. – Lights up for a few seconds when the player is turned on. I Front panel display (59) 58 57 GNU License Information Front panel display Regarding the GNU General Public License The software programs used on this component include the GNU/Linux system. The GNU/Linux system contains software licensed for use based on the terms of a GNU General Public License. If necessary, the user may request the source code for this licensed software. The source code is available on our website. Access the following URL to download: http://www.sony.net/Products/Linux Please refrain from making inquiries about the source code content. Details of the GNU General Public License can be found at the GNU website (http://www.gnu.org). The playback information is displayed as follows. A H – Lights up during playback. Example: When playing a DVD VIDEO or a BD-ROM B Playback information z Hint You can change the brightness of the front panel display by pressing DIMMER (page 24). GNU General Public License A Current title number C Elapsed time of the title Rear panel Version 2, June 1991 Copyright (C) 1989, 1991 Free Software Foundation, Inc. 59 Temple Place - Suite 330, Boston, MA 021111307, USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. Additional Information B Current chapter number Note that the chapter number is not displayed if the title’s elapsed time exceeds 10 hours. ◆Preamble The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public License is intended to guarantee your freedom to share and change free software-to make sure the software is free for all its users. This General Public License applies to most of the Free Software Foundation’s software and to any other program whose authors commit to using it. (Some other Free Software Foundation software is covered by the GNU Lesser General Public License instead.) You can apply it to your programs, too. When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs; and that you know you can do these things. To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These restrictions translate to certain responsibilities for you if you distribute copies of the software, or if you modify it. For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights. We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to copy, distribute and/or modify the software. Also, for each author’s protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the software is modified by someone else and passed on, we want its recipients to know that what they have is not the original, so that any problems introduced by others will not reflect on the original authors’ reputations. Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses, in effect making the program proprietary. To prevent this, For connections, see page 10 to 16. COMPONENT VIDEO OUT VIDEO OUT DIGITAL OUT PB HDMI OUT PR S VIDEO PCM/DTS/DOLBY DIGITAL COAXIAL OPTICAL 5.1CH OUTPUT AUDIO OUT Y VIDEO AC IN FRONT L L R R REAR CENTER WOOFER A AC IN terminal (16) F AUDIO OUT (L/R) jacks (13, 14) B HDMI OUT jack (11, 12, 15) G 5.1CH OUTPUT (FRONT L/R, REAR L/R, CENTER, WOOFER) jacks (14) C VIDEO OUT (VIDEO/S VIDEO) jacks (10) D COMPONENT VIDEO OUT (Y/PB/PR) jacks (10) E DIGITAL OUT (COAXIAL/OPTICAL) jacks (13, 14) 60 59 1-14 we have made it clear that any patent must be licensed for everyone’s free use or not licensed at all. The precise terms and conditions for copying, distribution and modification follow. TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION 0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License. The “Program”, below, refers to any such program or work, and a “work based on the Program” means either the Program or any derivative work under copyright law: that is to say, a work containing the Program or a portion of it, either verbatim or with modifications and/or translated into another language. (Hereinafter, translation is included without limitation in the term “modification”.) Each licensee is addressed as “you”. Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running the Program is not restricted, and the output from the Program is covered only if its contents constitute a work based on the Program (independent of having been made by running the Program). Whether that is true depends on what the Program does. 1. You may copy and distribute verbatim copies of the Program’s source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program. You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee. 2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions: a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change. b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part thereof, to be licensed as a whole at no charge to all third parties under the terms of this License. c) If the modified program normally reads commands interactively when run, you must cause it, when started running for such interactive use in the most ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty (or else, saying that you provide a warranty) and that users may redistribute the program under these conditions, and telling the user how to view a copy of this License. (Exception: if the Program itself is interactive but does not normally print such an announcement, your work based on the Program is not required to print an announcement.) These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the 3. 4. 5. Program, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it. Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Program. In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program) on a volume of a storage or distribution medium does not bring the other work under the scope of this License. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you also do one of the following: a) Accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or, b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing source distribution, a complete machine-readable copy of the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or, c) Accompany it with the information you received as to the offer to distribute corresponding source code. (This alternative is allowed only for noncommercial distribution and only if you received the program in object code or executable form with such an offer, in accord with Subsection b above.) The source code for a work means the preferred form of the work for making modifications to it. For an executable work, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the executable. However, as a special exception, the source code distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable. If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Program (or any work based Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally. ◆NO WARRANTY 11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BYAPPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THEPROGRAM “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIROR CORRECTION. 12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHOMAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL,SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. ◆END OF TERMS AND CONDITIONS ◆How to Apply These Terms to Your New Programs If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achieve this is to make it free software which everyone can redistribute and change under these terms. To do so, attach the following notices to the program. It is safest to attach them to the start of each source file to most effectively convey the exclusion of warranty; and each file should have at least the “copyright” line and a pointer to where the full notice is found. <one line to give the program’s name and an idea of what it does.> Copyright (C) yyyy name of author This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation; either version 2 of the License, or (at your option) any later version. This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. Also add information on how to contact you by electronic and paper mail. If the program is interactive, make it output a short notice like this when it starts in an interactive mode: Gnomovision version 69, Copyright (C) year name of author Gnomovision comes with ABSOLUTELY NO WARRANTY; for details type ‘show w’. This is free software, and you are welcome to redistribute it under certain conditions; type ‘show c’ for details. The hypothetical commands ‘show w’ and ‘show c’ should show the appropriate parts of the General Public License. Of course, the commands you use may be called something other than ‘show w’ and ‘show c’; they could even be mouse-clicks or menu items-whatever suits your program. You should also get your employer (if you work as a programmer) or your school, if any, to sign a “copyright disclaimer” for the program, if necessary. Here is a sample; alter the names: Yoyodyne, Inc., hereby disclaims all copyright interest in the program ‘Gnomovision’ (which makes passes at compilers) written by James Hacker. signature of Ty Coon, 1 April 1989 Ty Coon, President of Vice This General Public License does not permit incorporating your program into proprietary programs. If your program is a subroutine library, you may consider it more useful to permit linking proprietary applications with the library. If this is what you want to do, use the GNU Lesser General Public License instead of this License. GNU Lesser General Public License Version 2.1, February 1999 Copyright (C) 1991, 1999 Free Software Foundation, Inc. 59 Temple Place, Suite 330, Boston, MA 021111307, USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. [This is the first released version of the Lesser GPL. It also counts as the successor of the GNU Library Public License, version 2, hence the version number2.1.] and recompiling it. And you must show them these terms so they know their rights. We protect your rights with a two-step method: (1) we copyright the library, and (2) we offer you this license, which gives you legal permission to copy, distribute and/or modify the library. To protect each distributor, we want to make it very clear that there is no warranty for the free library. Also, if the library is modified by someone else and passed on, the recipients should know that what they have is not the original version, so that the original author’s reputation will not be affected by problems that might be introduced by others. Finally, software patents pose a constant threat to the existence of any free program. We wish to make sure that a company cannot effectively restrict the users of a free program by obtaining a restrictive license from a patent holder. Therefore, we insist that any patent license obtained for a version of the library must be consistent with the full freedom of use specified in this license. Most GNU software, including some libraries, is covered by the ordinary GNU General Public License. This license, the GNU Lesser General Public License, applies to certain designated libraries, and is quite different from the ordinary General Public License. We use this license for certain libraries in order to permit linking those libraries into non-free programs. When a program is linked with a library, whether statically or using a shared library, the combination of the two is legally speaking a combined work, a derivative of the original library. The ordinary General Public License therefore permits such linking only if the entire combination fits its criteria of freedom. The Lesser General Public License permits more lax criteria for linking other code with the library. We call this license the “Lesser” General Public License because it does Less to protect the user’s freedom than the ordinary General Public License. It also provides other free software developers Less of an advantage over competing non-free programs. These disadvantages are the reason we use the ordinary General Public License for many libraries. However, the Lesser license provides advantages in certain special circumstances. For example, on rare occasions, there may be a special need to encourage the widest possible use of a certain library, so that it becomes a de facto standard. To achieve this, non-free programs must be allowed to use the library. A more frequent case is that a free library does the same job as widely used non-free libraries. In this case, there is little to gain by limiting the free library to free software only, so we use the Lesser General Public License. In other cases, permission to use a particular library in non-free programs enables a greater number of people to use a large body of free software. For example, permission to use the GNU C Library in non-free programs enables many more people to use the whole GNU operating system, as well as its variant, the GNU/ Linux operating system. Although the Lesser General Public License is Less protective of the users’ freedom, it does ensure that the user of a program that is linked with the Library has the freedom and the wherewithal to run that program using a modified version of the Library. The precise terms and conditions for copying, distribution and modification follow. Pay close attention to the difference between a “work based on the library” and a “work that uses the library”. The former contains code derived from the library, whereas the latter must be combined with the library in order to run. Additional Information on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it. 6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients’ exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to this License. 7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Program at all. For example, if a patent license would not permit royalty-free redistribution of the Program by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Program. If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances. It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system, which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice. This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License. 8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License. 9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns. Each version is given a distinguishing version number. If the Program specifies a version number of this License which applies to it and “any later version”, you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Program does not specify a version number of this License, you may choose any version ever published by the Free Software Foundation. 10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to the author to ask for permission. For software which is copyrighted by the Free ◆Preamble The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public Licenses are intended to guarantee your freedom to share and change free software-to make sure the software is free for all its users. This license, the Lesser General Public License, applies to some specially designated software packages-typically libraries-of the Free Software Foundation and other authors who decide to use it. You can use it too, but we suggest you first think carefully about whether this license or the ordinary General Public License is the better strategy to use in any particular case, based on the explanations below. When we speak of free software, we are referring to freedom of use, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish); that you receive source code or can get it if you want it; that you can change the software and use pieces of it in new free programs; and that you are informed that you can do these things. To protect your rights, we need to make restrictions that forbid distributors to deny you these rights or to ask you to surrender these rights. These restrictions translate to certain responsibilities for you if you distribute copies of the library or if you modify it. For example, if you distribute copies of the library, whether gratis or for a fee, you must give the recipients all the rights that we gave you. You must make sure that they, too, receive or can get the source code. If you link other code with the library, you must provide complete object files to the recipients, so that they can relink them with the library after making changes to the library 1. 2. TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION 0. This License Agreement applies to any software library or other program which contains a notice placed by the copyright holder or other authorized party saying it may be distributed under the terms of this Lesser General Public License (also called “this License”). Each licensee is addressed as “you”. A “library” means a collection of software functions and/or data prepared so as to be conveniently linked with application programs (which use some of those functions and data) to form executables. The “Library”, below, refers to any such software library or work which has been distributed under these terms. A “work based on the Library” means either the Library or any derivative work under copyright law: that is to say, a work containing the Library or a portion of it, either verbatim or with modifications and/or translated straightforwardly into another language. (Hereinafter, translation is included without limitation in the term “modification”.) “Source code” for a work means the preferred form of the work for making modifications to it. For a library, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the library. Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running a program using the Library is not restricted, and output from such a program is covered only if its contents constitute a work based on the Library (independent of the use of the Library in a tool for writing it). Whether that is true depends on what the Library does and what the program that uses the Library does. You may copy and distribute verbatim copies of the Library’s complete source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and distribute a copy of this License along with the Library. You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee. You may modify your copy or copies of the Library or any portion of it, thus forming a work based on the Library, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions: a) The modified work must itself be a software library. b) You must cause the files modified to carry prominent notices stating that you changed the files and the date of any change. c) You must cause the whole of the work to be licensed at no charge to all third parties under the terms of this License. d) If a facility in the modified Library refers to a function or a table of data to be supplied by an application program that uses the facility, other than as an argument passed when the facility is invoked, then you must make a good faith effort to ensure that, in the event an application does not supply such function or table, the facility still operates, and performs whatever part of its purpose remains meaningful. (For example, a function in a library to compute square roots has a purpose that is entirely well-defined independent of the application. Therefore, Subsection 2d requires that any application-supplied function or table used by this function must be optional: if the application does not supply it, the square root function must still compute square roots.) These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Library, and can be 3. 4. 5. reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Library, the distribution of the whole must be on the terms of this license, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it. Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Library. In addition, mere aggregation of another work not based on the Library with the Library (or with a work based on the Library) on a volume of a storage or distribution medium does not bring the other work under the scope of this License. You may opt to apply the terms of the ordinary GNU General Public License instead of this License to a given copy of the Library. To do this, you must alter all the notices that refer to this License, so that they refer to the ordinary GNU General Public License, version 2, instead of to this License. (If a newer version than version 2 of the ordinary GNU General Public License has appeared, then you can specify that version instead if you wish.) Do not make any other change in these notices. Once this change is made in a given copy, it is irreversible for that copy, so the ordinary GNU General Public License applies to all subsequent copies and derivative works made from that copy. This option is useful when you wish to copy part of the code of the Library into a program that is not a library. You may copy and distribute the Library (or a portion or derivative of it, under Section 2) in object code or executable form under the terms of Sections1 and 2 above provided that you accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange. If distribution of object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place satisfies the requirement to distribute the source code, even though third parties are not compelled to copy the source along with the object code. A program that contains no derivative of any portion of the Library, but is designed to work with the Library by being compiled or linked with it, is called a “work that uses the Library”. Such a work, in isolation, is not a derivative work of the Library, and therefore falls outside the scope of this License. However, linking a “work that uses the Library” with the Library creates an executable that is a derivative of the Library (because it contains portions of the Library), rather than a “work that uses the library”. The executable is therefore covered by this License. Section 6 states terms for distribution of such executables. When a “work that uses the Library” uses material from a header file that is part of the Library, the object code for the work may be a derivative work of the Library even though the source code is not. Whether this is true is especially significant if the work can be linked without the Library, or if the work is itself a library. The threshold for this to be true is not precisely defined by law. If such an object file uses only numerical parameters, data structure layouts and accessors, and small macros and small inline functions (ten lines or less in length), ,continued 62 61 6. component itself accompanies the executable. It may happen that this requirement contradicts the license restrictions of other proprietary libraries that do not normally accompany the operating system. Such a contradiction means you cannot use both them and the Library together in an executable that you distribute. 7. You may place library facilities that are a work based on the Library side-by-side in a single library together with other library facilities not covered by this License, and distribute such a combined library, provided that the separate distribution of the work based on the Library and of the other library facilities is otherwise permitted, and provided that you do these two things: a) Accompany the combined library with a copy of the same work based on the Library, uncombined with any other library facilities. This must be distributed under the terms of the Sections above. b) Give prominent notice with the combined library of the fact that part of it is a work based on the Library, and explaining where to find the accompanying uncombined form of the same work. 8. You may not copy, modify, sublicense, link with, or distribute the Library except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense, link with, or distribute the Library is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance. 9. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Library or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Library(or any work based on the Library), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Library or works based on it. 10. Each time you redistribute the Library (or any work based on the Library), the recipient automatically receives a license from the original licensor to copy, distribute, link with or modify the Library subject to these terms and conditions. You may not impose any further restrictions on the recipients’ exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties with this License. 11. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Library at all. For example, if a patent license would not permit royalty-free redistribution of the Library by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Library. If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply, and the section as a whole is intended to apply in other circumstances. It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice. This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License. 12. If the distribution and/or use of the Library is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Library under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License. 13. The Free Software Foundation may publish revised and/or new versions of the Lesser General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns. Each version is given a distinguishing version number. If the Library specifies a version number of this License which applies to it and “any later version”, you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Library does not specify a license version number, you may choose any version ever published by the Free Software Foundation. 14. If you wish to incorporate parts of the Library into other free programs whose distribution conditions are incompatible with these, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally. ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE LIBRARY (INCLUDING BUT NOTLIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OFTHE LIBRARY TO OPERATE WITH ANY OTHER SOFTWARE), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. ◆END OF TERMS AND CONDITIONS ◆How to Apply These Terms to Your New Libraries If you develop a new library, and you want it to be of the greatest possible use to the public, we recommend making it free software that everyone can redistribute and change. You can do so by permitting redistribution under these terms (or, alternatively, under the terms of the ordinary General Public License). To apply these terms, attach the following notices to the library. It is safest to attach them to the start of each source file to most effectively convey the exclusion of warranty; and each file should have at least the “copyright” line and a pointer to where the full notice is found. <one line to give the library’s name and an idea of what it does.> Copyright (C) year name of author This library is free software; you can redistribute it and/or modify it under the terms of the GNU Lesser General Public License as published by the Free Software Foundation; either version 2.1 of the License, or (at your option) any later version. This library is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU Lesser General Public License for more details. You should have received a copy of the GNU Lesser General Public License along with this library; if not, write to the Free Software Foundation, Inc., 59Temple Place, Suite 330, Boston, MA 02111-1307, USA Also add information on how to contact you by electronic and paper mail. You should also get your employer (if you work as a programmer) or your school, if any, to sign a “copyright disclaimer” for the library, if necessary. Here is a sample; alter the names: Yoyodyne, Inc., hereby disclaims all copyright interest in the library ‘Frob’ (a library for tweaking knobs) written by James Random Hacker. signature of Ty Coon, 1 April 1990 Ty Coon, President of Vice That’s all there is to it! Additional Information then the use of the object file is unrestricted, regardless of whether it is legally a derivative work. (Executables containing this object code plus portions of the Library will still fall under Section 6.) Otherwise, if the work is a derivative of the Library, you may distribute the object code for the work under the terms of Section 6. Any executables containing that work also fall under Section 6, whether or not they are linked directly with the Library itself. As an exception to the Sections above, you may also combine or link a “work that uses the Library” with the Library to produce a work containing portions of the Library, and distribute that work under terms of your choice, provided that the terms permit modification of the work for the customer’s own use and reverse engineering for debugging such modifications. You must give prominent notice with each copy of the work that the Library is used in it and that the Library and its use are covered by this License. You must supply a copy of this License. If the work during execution displays copyright notices, you must include the copyright notice for the Library among them, as well as a reference directing the user to the copy of this License. Also, you must do one of these things: a) Accompany the work with the complete corresponding machinereadable source code for the Library including whatever changes were used in the work (which must be distributed under Sections 1 and 2 above); and, if the work is an executable linked with the Library, with the complete machine-readable “work that uses the Library”, as object code and/or source code, so that the user can modify the Library and then relink to produce a modified executable containing the modified Library. (It is understood that the user who changes the contents of definitions files in the Library will not necessarily be able to recompile the application to use the modified definitions.) b) Use a suitable shared library mechanism for linking with the Library. A suitable mechanism is one that (1) uses at run time a copy of the library already present on the user’s computer system, rather than copying library functions into the executable, and (2) will operate properly with a modified version of the library, if the user installs one, as long as the modified version is interfacecompatible with the version that the work was made with. c) Accompany the work with a written offer, valid for at least three years, to give the same user the materials specified in Subsection 6a, above, for a charge no more than the cost of performing this distribution. d) If distribution of the work is made by offering access to copy from a designated place, offer equivalent access to copy the above specified materials from the same place. e) Verify that the user has already received a copy of these materials or that you have already sent this user a copy. For an executable, the required form of the “work that uses the Library” must include any data and utility programs needed for reproducing the executable from it. However, as a special exception, the materials to be distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that ◆NO WARRANTY 15. BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE LIBRARY, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE LIBRARY “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIESOF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THELIBRARY IS WITH YOU. SHOULD THE LIBRARY PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION. 16. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHOMAY MODIFY AND/OR REDISTRIBUTE THE LIBRARY AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING OpenSSL License ◆OpenSSL Copyright (c) 1998-2004 The OpenSSL Project. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. ,continued 64 63 1-15 3. 4. 5. 6. All advertising materials mentioning features or use of this software must display the following acknowledgment: “This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.openssl.org/)” The names “OpenSSL Toolkit” and “OpenSSL Project” must not be used to endorse or promote products derived from this software without prior written permission. For written permission, please contact [email protected]. Products derived from this software may not be called “OpenSSL” nor may “OpenSSL” appear in their names without prior written permission of the OpenSSL Project. Redistributions of any form whatsoever must retain the following acknowledgment: “This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit (http://www.openssl.org/)” THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT “AS IS” AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. This product includes cryptographic software written by Eric Young ([email protected]). This product includes software written by Tim Hudson ([email protected]). Original SSLeay License ◆Original SSLeay Copyright (C) 1995-1998 Eric Young ([email protected]) All rights reserved. This package is an SSL implementation written by Eric Young ([email protected]). The implementation was written so as to conform with Netscapes SSL. This library is free for commercial and noncommercial use as long as the following conditions are aheared to. The following conditions apply to all code found in this distribution, be it the RC4, RSA, lhash, DES, etc., code; not just the SSL code. The SSL documentation included with this distribution is covered by the same copyright terms except that the holder is Tim Hudson ([email protected]). Copyright remains Eric Young's, and as such any Copyright notices in the code are not to be removed. If this package is used in a product, Eric Young should be given attribution as the author of the parts of the library used. This can be in the form of a textual message at program startup or in documentation (online or textual) provided with the package. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. 3. All advertising materials mentioning features or use of this software must display the following acknowledgement: “This product includes cryptographic software written by Eric Young ([email protected])” The word 'cryptographic' can be left out if the rouines from the library being used are not cryptographic related :-). 4. If you include any Windows specific code (or a derivative thereof) from the apps directory (application code) you must include an acknowledgement: “This product includes software written by Tim Hudson ([email protected])” THIS SOFTWARE IS PROVIDED BY ERIC YOUNG ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. The licence and distribution terms for any publically available version or derivative of this code cannot be changed. i.e. this code cannot simply be copied and put under another distribution licence [including the GNU Public Licence.] FreeType The FreeType Project is copyright (C) 19962000 by David Turner, Robert Wilhelm, and Werner Lemberg. All rights reserved except as specified below. THE FREETYPE PROJECT IS PROVIDED ‘AS IS’ WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT WILL ANY OF THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY DAMAGES CAUSED BY THE USE OR THE INABILITY TO USE, OF THE FREETYPE PROJECT. Howl Copyright (c) 2003, 2004 Porchdog Software All rights reserved. THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. jpeg-6b If only executable code is distributed, then the accompanying documentation must state that “this software is based in part on the work of the Independent JPEG Group”. libpng COPYRIGHT NOTICE, DISCLAIMER, and LICENSE: If you modify libpng you may insert additional notices immediately following this sentence. Cosmin Truta libpng versions 1.0.7, July 1, 2000, through 1.2.5 - October 3, 2002, are Copyright (c) 2000-2002 Glenn Randers-Pehrson, and are distributed according to the same disclaimer and license as libpng-1.0.6 with the following individuals added to the list of Contributing Authors Simon-Pierre Cadieux Eric S. Raymond Gilles Vollant and with the following additions to the disclaimer: There is no warranty against interference with your enjoyment of the library or against infringement. There is no warranty that our efforts or the library will fulfill any of your particular purposes or needs. This library is provided with all faults, and the entire risk of satisfactory quality, performance, accuracy, and effort is with the user. libpng versions 0.97, January 1998, through 1.0.6, March 20, 2000, are Copyright (c) 1998, 1999 Glenn Randers-Pehrson, and are distributed according to the same disclaimer and license as libpng-0.96, with the following individuals added to the list of Contributing Authors: Tom Lane Glenn Randers-Pehrson Willem van Schaik libpng versions 0.89, June 1996, through 0.96, May 1997, are Copyright (c) 1996, 1997 Andreas Dilger Distributed according to the same disclaimer and license as libpng-0.88, with the following individuals added to the list of Contributing Authors: John Bowler Kevin Bracey Sam Bushell Magnus Holmgren Greg Roelofs Tom Tanner For the purposes of this copyright and license, “Contributing Authors” is defined as the following set of individuals: Andreas Dilger Dave Martindale Guy Eric Schalnat Paul Schmidt Tim Wegner The PNG Reference Library is supplied “AS IS”. The Contributing Authors and Group 42, Inc. disclaim all warranties, expressed or implied, including, without limitation, the warranties of merchantability and of fitness for any purpose. The Contributing Authors and Group 42, Inc. assume no liability for direct, indirect, incidental, special, exemplary, or consequential damages, which may result from the use of the PNG Reference Library, even if advised of the possibility of such damage. Permission is hereby granted to use, copy, modify, and distribute this source code, or portions hereof, for any purpose, without fee, subject to the following restrictions: 1. 2. 3. The origin of this source code must not be misrepresented. Altered versions must be plainly marked as such and must not be misrepresented as being the original source. This Copyright notice may not be removed or altered from any source or altered source distribution. The Contributing Authors and Group 42, Inc. specifically permit, without fee, and encourage the use of this source code as a component to supporting the PNG file format in commercial products. If you use this source code in a product, acknowledgment is not required but would be appreciated. A “png_get_copyright” function is available, for convenient use in “about” boxes and the like: printf(“%s”,png_get_copyright(NULL)); Glossary Luxi fonts copyright (c) 2001 by Bigelow & Holmes Inc. Luxi font instruction code copyright (c) 2001 by URW++ GmbH. All Rights Reserved. Luxi is a registered trademark of Bigelow & Holmes Inc. THE FONT SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OF COPYRIGHT, PATENT, TRADEMARK, OR OTHER RIGHT. IN NO EVENT SHALL BIGELOW & HOLMES INC. OR URW++ GMBH. BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, INCLUDING ANY GENERAL, SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF THE USE OR INABILITY TO USE THE FONT SOFTWARE OR FROM OTHER DEALINGS IN THE FONT SOFTWARE. AACS “Advanced Access Content System” is a specification for managing digital entertainment contents stored on the next generation of prerecorded and recorded optical media. The specification enables consumers to enjoy digital entertainment content, including high-definition content. AVCHD (page 6) The AVCHD format is a high definition digital video camera format used to record SD (standard definition) or HD (high definition) signals of either the 1080i specification*1 or the 720p specification*2 on DVDs, using efficient data compression coding technology. The MPEG-4 AVC/H.264 format is adopted to compress video data, and the Dolby Digital or Linear PCM is used to compress audio data. The MPEG-4 AVC/H.264 format is capable of compressing images at higher efficiency than that of the conventional image compression format. The MPEG-4 AVC/ H.264 format enables a high definition (HD) video signal shot on a digital video camera recorder to be recorded on DVDs in the same way as for a standard definition (SD) television signal. TIFF Copyright (c) 1988-1997 Sam Leffler Copyright (c) 1991-1997 Silicon Graphics, Inc. THE SOFTWARE IS PROVIDED “AS-IS” AND WITHOUT WARRANTY OF ANY KIND, EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND, OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. Also, the PNG logo (in PNG format, of course) is supplied in the files “pngbar.png” and “pngbar.jpg (88x31) and “pngnow.png” (98x31). This software is based in part on zlib see http:// www.zlib.net for information. Libpng is OSI Certified Open Source Software. OSI Certified Open Source is a certification mark of the Open Source Initiative. This software is based in part on Mozilla Public License 1.1 see http://www.mozilla.org/MPL/ for information. Glenn Randers-Pehrson glennrp at users.sourceforge.net December 3, 2004 This software is based in part on Apple Public Source License or the reciient's rights thereunder see http://developer.apple.com/ for information. Libungif This software is based in part on Intel License see http://www.intel.com/ for information. Additional Information libpng version 1.2.6, December 3, 2004, is Copyright (c) 2004 Glenn Randers-Pehrson, and is distributed according to the same disclaimer and license as libpng-1.2.5 with the following individual added to the list of Contributing Authors libpng versions 0.5, May 1995, through 0.88, January 1996, are Copyright (c) 1995, 1996 Guy Eric Schalnat, Group 42, Inc. *1 A high definition specification that utilizes1080 effective scanning lines and the interlace format. *2 A high definition specification that utilizes 720 effective scanning lines and the progressive format. BD-J application The BD-ROM format supports Java for interactive functions. “BD-J” offers content providers almost unlimited functionality when creating interactive BD-ROM titles. The GIFLIB distribution is Copyright (c) 1997 Eric S. Raymond THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE. BD-R TinyLogin This software is copyright 1988 - 1994, Julianne Frances Haugh. All rights reserved. BD-R (Blu-ray Disc Recordable) is a recordable, write-once Blu-ray Disc, available in the same capacities as the BD below. Since contents can be recorded and cannot be overwritten, a BD-R can be used to archive valuable data or storing and distributing video material. The shadow utilities license This software is copyright 1988 - 1994, Julianne Frances Haugh. All rights reserved. Vera.ttf/VeraMono.ttf Copyright © 2003 by Bitstream, Inc. All Rights Reserved. Bitstream Vera SansBitstreamVeraSans-RomanRelease 1.10 Copyright © 2003 by Bitstream, Inc. All Rights Reserved. Bitstream Vera is a trademark of Bitstream, Inc. Interlace format shows every other line of an image as a single “field” and is the standard method for displaying images on television. The even number field shows the even numbered lines of an image, and the odd numbered field shows the odd numbered lines of an image. DVD-RW (page 5) A DVD-RW is a recordable and rewritable disc that is the same size as a DVD VIDEO. The DVD-RW has two different modes: VR mode and Video mode. DVDs created in Video mode have the same format as a DVD VIDEO, while discs created in VR (Video Recording) mode allow the contents to be programmed or edited. DVD+R (page 5) DVD+RW (page 5) A DVD+RW (read “plus RW”) is a recordable and rewritable disc. DVD+RWs use a recording format that is comparable to the DVD VIDEO format. Film-based software, Video-based software DVDs can be classified as Film-based or Video-based software. Film-based DVDs contain the same images (24 frames per second) that are shown at movie theaters. Video-based DVDs, such as television dramas or sitcoms, display images at 30 frames (or 60 fields) per second. One of the video data compression schemes established by the Moving Picture Experts Group (MPEG), which is adopted for DVD VIDEOs and digital broadcasts worldwide. The scheme specifies MPEG-2 PS (Program Stream) for recordable media such as a DVD VIDEO, and MPEG-2 TS (Transport Stream) for digital broadcasts and other communications. Pop-up menu An enhanced menu operation available on BD-ROMs. The pop-up menu appears when MENU is pressed during playback, and can be operated while playback is in progress. Progressive format Compared to the Interlace format that alternately shows every other line of an image (field) to create one frame, the Progressive format shows the entire image at once as a single frame. This means that while the Interlace format can show 30 frames/60 fields in one second, the Progressive format can show 60 frames in one second. The overall picture quality increases and still images, text, and horizontal lines appear sharper. Title (page 26) The longest section of a picture or music feature on a DVD, movie, etc., in video software, or the entire album in audio software. Specifications Language Code List A disc format developed for recording/ playing high-definition (HD) video (for HDTV, etc.), and for storing large amounts of data. A single layer Blu-ray Disc holds up to 25 GB, and a dual-layer Blu-ray Disc holds up to 50 GB of data. Digital audio compression technology that DTS, Inc. developed. This technology conforms to multi-channel surround sound. The rear channel is stereo and there is a discrete subwoofer channel in this format. DTS provides the same discrete channels of high quality digital audio. Good channel separation is realized because all of the channel data is recorded discretely and little deterioration occurs because all channel data processing is digital. DTS-HD (page 48) Chapter (page 25) Sections of a picture or a music feature that are smaller than titles. A title is composed of several chapters. Depending on the disc, no chapters may be recorded. Dolby Digital (page 47) Digital audio compression technology developed by Dolby Laboratories. This technology conforms to multi-channel surround sound. The rear channel is stereo and there is a discrete subwoofer channel in this format. Dolby Digital provides the same discrete channels of high quality digital audio found in “Dolby Digital” theater surround sound systems. Good channel separation is realized because all of the channel data is recorded discretely and little deterioration occurs because all channel data processing is digital. Dolby Digital Plus (page 48) Developed as an extension to Dolby Digital, the audio coding technology supports 7.1 multi-channel surround sound. Dolby Surround (Pro Logic) (page 47) Audio signal processing technology that Dolby Laboratories developed for surround sound. When the input signal contains a surround component, the Pro Logic process outputs the front, center and rear signals. The rear channel is monaural. DTS-HD is an extended format of the Coherent Acoustics audio coding system, which also encompasses DTS Digital Surround, DTS-ES, and DTS 96/ 24. DTS-HD is highly flexible in supporting the number of discrete surround sound channels. While 7.1ch surround sound is planned for Blu-ray Discs, the audio signals can be downmixed to 5.1 or 2 channels for backward compatibility, and the reproduced audio quality can either be at the bit rate of DTS Digital Surround or the lossless mode. DVD VIDEO (page 5) A disc format that contains up to eight hours of moving pictures on a disc the same diameter as a CD. A single-layer single sided DVD holds up to 4.7 GB; a double layer single-sided DVD, 8.5 GB; a single layer double-sided DVD, 9.4 GB; double-layer double-sided DVD, 17 GB. The MPEG 2 format is adopted for the efficient video data compression. The variable rate coding technology that changes the data to be allocated according to the status of the picture is adopted for reproducing high-quality pictures. Audio information is recorded in a multi-channel format, such as Dolby Digital, allowing for a realistic audio presence. Language (abbr.) Code Language (abbr.) Code Hindi (hi) 0809 Sinhalese (si) 1909 Croatian (hr) 0818 lovak (sk) 1911 Hungarian (hu) 0821 Slovenian (sl) 1912 Armenian (hy) 0825 Samoan (sm) 1913 Interlingua (ia) 0901 Shona (sn) 1914 Interlingue (ie) 0905 Somali (so) 1915 Laser: Semiconductor laser Language (abbr.) Code Inupiak (ik) 0911 Albanian (sq) Outputs Japanese (ja) 1001 Indonesian (in) 0914 Serbian (sr) 1918 (Jack name: Jack type/Output level/ Load impedance) AUDIO OUT L/R: Phono jack/2 Vrms/10 kilohms DIGITAL OUT (OPTICAL): Optical output jack/–18 dBm (wave length 660 nm) DIGITAL OUT (COAXIAL): Phono jack/0.5 Vp-p/75 ohms 5.1CH OUTPUT: Phono jack/2 Vrms/10 kilohms HDMI OUT: HDMI 19-pin standard connector COMPONENT VIDEO OUT(Y, PB, PR): Phono jack/Y: 1.0 Vp-p/PB, PR: progressive or interlace = 0.7 Vp-p/75 ohms VIDEO: Phono jack/1.0 Vp-p/75 ohms S VIDEO: 4-pin mini DIN/Y: 1.0 Vp-p, C: 0.286 Vp-p/75 ohms English (en) 0514 Icelandic (is) 0919 Siswati (ss) 1919 French (fr) 0618 Hebrew (iw) 0923 Sesotho (st) German (de) 0405 Yiddish (ji) 1009 Sundanese (su) 1921 Italian (it) 0920 Javanese (jw) 1023 Swedish (sv) 1922 For details, see page 49. System General Power requirements: 120 V AC, 60 Hz Power consumption: 33 W Dimensions (approx.): 430 u 79 u 375 mm (17 × 3 1/8 × 14 7/8 in.) (width/height/depth) incl. projecting parts Mass (approx.): 4.5 kg (10 lb) Operating temperature: 5 ºC to 35 ºC (41°F to 95°F) Operating humidity: 25 % to 80 % Spanish (es) See page 9. HDMI is an interface that supports both video and audio on a single digital connection. The HDMI connection carries standard to high definition video signals and multi-channel audio signals to AV components such as HDMI equipped TVs, in digital form without degradation. The HDMI specification supports HDCP (High-bandwidth Digital Contents Protection), a copy protection technology for digital entertainment contents for HDMI. Specifications and design are subject to change without notice. 67 68 1-16 1920 0519 Georgian (ka) 1101 Swahili (sw) 1923 1412 Kazakh (kk) 1111 Tamil (ta) 2001 Russian (ru) 1821 Greenlandic (kl) 1112 Telugu (te) 2005 Chinese (zh) 2608 Cambodian (km) 1113 Tajik (tg) 2007 Korean (ko) 1115 Kannada (kn) 1114 Thai (th) Greek (el) 0512 Kashmiri (ks) 1119 Tigrinya (ti) 2009 Afar (aa) 0101 Kurdish (ku) 1121 Turkmen (tk) 2011 2008 0102 Kirghiz (ky) 1125 Tagalog (tl) 2012 Afrikaans (af) 0106 Latin (la) 1201 Setswana (tn) 2014 Amharic (am) 0113 Lingala (ln) 1214 Tonga (to) 2015 Arabic (ar) 0118 Laothian (lo) 1215 Turkish (tr) 2018 Assamese (as) 0119 Lithuanian (lt) 1220 Tsonga (ts) 2019 Aymara (ay) 0125 Latvian (lv) 1222 Tatar (tt) 2020 Azerbaijani (az) Supplied accessories HDMI (High-Definition Multimedia Interface) 1917 Dutch (nl) Abkhazian (ab) Additional Information A DVD+R (read “plus R”) is a recordable disc that is the same size as a DVD VIDEO. Contents can be recorded only once to a DVD+R, and will have the same format as a DVD VIDEO. MPEG-2 Blu-ray Disc (BD) (page 5) DTS (page 47) 66 65 Interlace format Dolby TrueHD is a lossless coding technology that supports up to 8 channels of multi-channel surround sound for the next generation optical discs. The reproduced sound is true to the original source bit-for-bit. BD-RE (Blu-ray Disc Rewritable) is a recordable and rewritable Blu-ray Disc, available in the same capacities as the BD below. The re-recordable feature makes extensive editing and timeshifting applications possible. Bigelow & Holmes Inc and URW++ GmbH Luxi font license A DVD-R is a recordable disc that is the same size as a DVD VIDEO. Contents can be recorded only once to a DVD-R, and will have the same format as a DVD VIDEO. The DVD-R has two different modes: VR mode and Video mode. DVDs created in Video mode have the same format as a DVD VIDEO, while discs created in VR (Video Recording) mode allow the contents to be programmed or edited. Dolby TrueHD (page 48) BD-ROMs (Blu-ray Disc Read-Only Memory) are commercially produced discs and are available in the same capacities as the BD below. Other than conventional movie and video contents, these discs have enhanced features such as interactive content, menu operations using pop-up menus (see below), selection of subtitle display, and slideshow. Although a BD-ROM may contain any form of data, most BD ROM discs will contain movies in High Definition format, for playback on Bluray Disc players. BD-RE Luxi font DVD-R (page 5) BD-ROM (page 5) 0126 Malagasy (mg) 1307 Twi (tw) Bashkir (ba) 0201 Maori (mi) 1309 Ukrainian (uk) 2111 Byelorussian (be) 0205 Macedonian (mk) 1311 Urdu (ur) 2118 Bulgarian (bg) 0207 Malayalam (ml) 1312 Uzbek (uz) 2126 Bihari (bh) 0208 Mongolian (mn) 1314 Vietnamese (vi) 2209 Bislama (bi) 0209 Moldavian (mo) 1315 Volapük (vo) 2215 Bengali (bn) 2023 0214 Marathi (mr) 1318 Wolof (wo) 2315 Tibetan (bo) 0215 Malay (ms) 1319 Xhosa (xh) 2408 Breton (br) 0218 Maltese (mt) 1320 Yoruba (yo) 2515 Catalan (ca) 0301 Burmese (my) 1325 Zulu (zu) 2621 Corsican (co) 0315 Nauru (na) 1401 Czech (cs) 0319 Nepali (ne) 1405 Welsh (cy) 0325 Norwegian (no) Danish (da) 0401 Occitan (oc) 1503 Bhutani (dz) 0426 Oromo (om) 1513 Esperanto (eo) 1415 0515 Oriya (or) Estonian (et) 0520 Panjabi (pa) 1601 Basque (eu) 0521 Polish (pl) 1612 Persian (fa) 0601 Pashto, Pushto (ps) 1619 Finnish (fi) 0609 Portuguese (pt) 1620 Fiji (fj) 0610 Quechua (qu) 1721 Faroese (fo) 0615 Rhaeto-Romance (rm) 1813 Frisian (fy) 0625 Kirundi (rn) 1814 Irish (ga) 0701 Romanian (ro) 1815 Scots-Gaelic (gd) 0704 Kinyarwanda (rw) 1823 Galician (gl) 0712 Sanskrit (sa) 1901 Guarani (gn) 0714 Sindhi (sd) 1904 Gujarati (gu) 0721 Sangho (sg) 1907 Hausa (ha) 0801 Serbo-Croatian (sh) 1908 1518 Index Parental Control Country/Area Code List Words in quotations appear in the onscreen displays. Area (abbr.) Code Argentina (ar) 0118 Numerics Australia (au) 0121 5.1CH OUTPUT 14, 51 Austria (at) 0120 Belgium (be) 0205 Brazil (br) 0218 Canada (ca) 0301 0314 Denmark (dk) 0411 Finland (fi) 0609 France (fr) 0618 Germany (de) A “A/V Control” 22 AACS 66 ANGLE 24 AUDIO 24 “Audio Control” 27 “Audio Output Mode” 51 “Audio Setup” 47 AVCHD 6, 66 0312 China (cn) B 0405 0811 India (in) 0914 Indonesia (id) 0904 Italy (it) 0920 Batteries 16 Blu-ray Disc 5, 66 ‘BRAVIA’ Theatre Sync 11 Additional Information Hong Kong (hk) C CD 5 Chapter 66 Color buttons 24 Connecting the audio cords 12 the video cords 10 Japan (jp) 1016 Korea, Republic of (kr) 1118 Malaysia (my) 1325 Mexico (mx) 1324 Netherlands (nl) 1412 New Zealand (nz) 1426 D Norway (no) 1415 DIMMER 24 Disc Information 26 DISPLAY 24 Display front panel display 59 Dolby Digital 14, 47, 66 Dolby Digital Plus 48, 66 Dolby TrueHD 48, 66 DTS 47, 66 “DTS Downmix” 47 DTS-HD 48, 66 DVD VIDEO 66 DVD+R 67 DVD+RW 67 DVD-R 67 DVD-RW 67 Pakistan (pk) 1611 Philippines (ph) 1608 Portugal (pt) 1620 Russian Federation (ru) 1821 Singapore (sg) 1907 Spain (es) 0519 Switzerland (ch) 0308 Sweden (se) 1905 Taiwan (tw) 2023 Thailand (th) 2008 United Kingdom (gb) 0702 United States of America (us) 2119 “Language” 49 M For details, see pages 50 and 52. Chile (cl) L E Easy Setup 18 F Film based software 67 Front panel display 59 H HDMI 11, 12, 18, 45, 47, 67 HDMI Control 11, 21, 52 I Interlace format 67 70 69 1-17 “Memory” 28 “Movies” 32 MPEG 32 “Music” 36 O “Options” 52 P “Parental Control” 50 “Photos” 40 POP UP/MENU 25 Pro Logic 14, 47, 66 Progressive format 67 R Region code 7 Remote 16, 17, 24 Resetting the Player 53 S Searching 26, 34, 38, 42 “Setup” 22 Setup Displays 44 “Slideshow” 41 “Speaker Setup” 51 “Speakers” 12, 51 SUBTITLE 24 T Title 67 Title List 22 TOP MENU 25 Troubleshooting 54 “TV Type” 45 U Usable discs 5 V Video based software 67 “Video Control” 28 “Video Setup” 45 MEMO 1-18E BDP-S300/S301 SECTION 2 DISASSEMBLY AND REASSEMBLY 2-1. DISASSEMBLY • This set can be disassembled in the order shown below. 2-1-1. DISASSEMBLY FLOW SET 2-1-2. UPPER CASE (Page 2-1) 2-1-3. TRAY COVER ASSY (Page 2-2) 2-1-5. MAIN BOARD (Page 2-3) 2-1-6. AU-258 BOARD (Page 2-3) 2-1-7. POWER BLOCK (Page 2-4) 2-1-4. BD DRIVE (SERVICE USE) (Page 2-2) Note: Follow the disassembly procedure in the numerical order given. 2-1-2. UPPER CASE 3 upper case 1 tapping screw 2 three screws 1 tapping screw 2-1 2-1-3. TRAY COVER ASSY 1 Insert a clip in the hole of a drive and open a tray. 4 tray cover assy 2 3 two claws 2-1-4. BD DRIVE (SERVICE USE) 5 two screws 5 two screws 8 BD drive (service use) 6 7 connector 1 three claws 4 two screws 3 connector 1 three claws 2 front panel assy 2-2 2-1-5. MAIN BOARD 8 six screws (BV3) 4 connector 9 MAIN board 5 two connectors 1 harness (MBD-003) 6 four screws (BV3) 7 screw (P3) 2 connector 3 connector 2-1-6. AU-258 BOARD 3 four screws (BV3) 1 connector 5 AU-258 board 2 three screws (BV3) 2-3 2-1-7. POWER BLOCK 1 two connectors 2 connector 3 five screws (BV3) 4 power block 2-1-8. CIRCUIT BOARDS LOCATION AU-258 board MAIN board FL-176 board power block FR-271 board 2-4 2-2. REASSEMBLY • This set can be assembled in the order shown below. 2-2-1. UPPER CASE 1 upper case 3 tapping screw 2 three screws 3 tapping screw 2-2-2. TRAY COVER ASSY 1 Insert a clip in the hole of a drive and open a tray. 3 tray cover assy 2 4 two claws 2-5 2-2-3. BD DRIVE (SERVICE USE) 4 two screws 4 two screws 1 BD drive (service use) 3 2 connector 8 three claws 5 two screws 6 connector 8 three claws 7 front panel assy 2-2-4. MAIN BOARD 2 six screws (BV3) 7 connector 1 MAIN board 6 two connectors 9 harness (MBD-003) 3 four screws (BV3) 4 screw (P3) 5 connector 8 connector 2-6 2-2-5. FL-176 BOARD, FR-271 BOARD 1 FL-176 board 2 two screws 5 flexible flat cable (FLR-011) 4 two screws 3 FR-271 board 2-2-6. DC FAN 1 DC fan 3 connector 2 two screws 2-7 MEMO 2-8E BDP-S300/S301 SECTION 3 BLOCK DIAGRAMS 3-1. MAIN BLOCK DIAGRAM CN5701 MAIN BOARD (DB-BMB102) 256MByte 128MByte DDR 512Mbit DDR 512Mbit DRAM0 DRAM1 I2S CN1802 BD-ROM DRIVE (BDV-102SO) Parallel ATAPI DIGITAL OUT Flash 512Mbit OPTICAL SPDIF1 COAXIAL 27MHz VIDEO OUT BD PLAYER PROCESSOR 1K EEPROM CVBS/Y/C VIDEO VIDEO DRIVER S VIDEO I2C COMPONENT VIDEO OUT Y CN3501 LED_PON FLDATA FLCLK FLSTB LED_FL_OFF LED_HDMI LED_HD LED_Blue Y/Cb/Cr 7 27 29 26 21 20 19 5 VIDEO BUFFER PB PR FIP/LED SPIDF0 I2S HDMI OUT HDMI Tx VOUT 24bit FL/FR (SEE PAGE 3-5) KEY0 KEY1 3 23 MODEL 1 KEY Sub Microcomputer I2C 4 CN6701 IR FAN 1 05 3-1 3-2 XAMUTE 2 XMMUTE 1 ADATA5_1 27 ADATA5_2 26 ALRCK 22 ADATA5_0 21 ABCLK 20 MCLK 18 24 23 16 15 14 13 12 DAC_XCS_2 DAC_XRST DAC_MDO DAC_MDI DAC_MC DAC_XCS_1 DAC_MUT AUDIO (SEE PAGE 3-3) BDP-S300/S301 3-2. AUDIO BLOCK DIAGRAM AU-258 BOARD (SEE PAGE 4-5) ADATA5_2 ALRCK ABCLK MCLK DAC_XCS_2 DAC_XRST DAC_MDO DAC_MDI CN001 DAC_XCS_2 DAC_XCS_2 24 DAC_XRST DAC_XRST 23 DAC_MDO DAC_MDO 16 DAC_MDI DAC_MDI 15 DAC_MC DAC_MC 14 DAC_XCS_1 DAC_XCS_1 13 DAC_MUT DAC_MUT 12 DAC_MC DAC_MUT ADATA5_1 3 DATA ALRCK 1 LRCK ABCLK 2 BICK Aout L- 18 5 MCLK MCLK IC011 AMP IC008 AUDIO DAC 28 X-MS DAC_XCS_2 6 DAC_XRST – 6 X-RST Aout L+ 17 5 + 7 DAC_MDO 25 MDO 3 26 MDI 27 MC + – DAC_MDI 1 DAC_MC 2 DAC_MUT 4 MUTE 3 DATA 1 LRCK 2 BICK 5 MCLK 28 X-MS Aout L- 18 IC010 AMP IC007 AUDIO DAC 6 – 6 X-RST Aout L+ 17 5 + 3 + – 7 25 MDO 26 MDI 27 MC 1 J001 2 CENTER 4 MUTE WOOFER Aout R+ 13 23 DZFL Aout R+ 13 23 DZFL 22 DZFR Q022 MUTE 22 DZFR Q023 MUTE L Aout R- 12 Aout R- 12 MCLK 18 ABCLK 20 ADATA 5_0 MAIN (SEE PAGE 3-2) 21 REAR R MCLK ABCLK Q020 MUTE Q021 MUTE ADATA 5_0 ALRCK ALRCK 22 ADATA 5_2 ADATA 5_1 26 ADATA5_0 ADATA 5_2 ALRCK ABCLK ADATA 5_1 27 MCLK 10 9 5 4 1 2 Q009 SW DAC_XCS_1 Q013 SW DAC_XRST DAC_MDO IC004 GATE XMMUTE 1 XAMUTE 2 Q001 MUTE DRIVE 8 Q003 MUTE DRIVE Q017 SW DAC_MDI 6 DAC_MC 3 DAC_MUT L 3 DATA 1 LRCK 2 BICK 5 MCLK 28 X-MS 6 X-RST Aout L- 18 IC009 AMP IC006 AUDIO DAC J003 6 – Aout L+ 17 5 + L 7 25 MDO R 26 MDI 3 27 MC 2 + – 1 4 MUTE Q018 MUTE A out R+ 13 Q015 SW Q014 SW 23 DZFL 22 DZFR Q011 SW FRONT R Aout R- 12 Q008 SW Q007 SW Q006 SW 05 3-3 3-4 Q019 MUTE AUDIO OUT 5.1CH OUTPUT BDP-S300/S301 3-3. FL/FR BLOCK DIAGRAM FL-176 BOARD (SEE PAGE 4-13) IC100 FL DRIVE 7 DIN SEG1 | SEG16 14 | 29 ND100 FLUORESCENT INDICATOR TUBE S(1)-(16) 8 CLK 9 STB GRID2 41 | | GRID12 31 COM(1)-(11) CN100 LED_PON FR-271 BOARD (SEE PAGE 4-17) 24 4 2 5 28 FLDATA FLCLK FLSTB KEY 0 CN101 3 KEY0 CN600 9 S100 S600 A 1 KEY1 4 8 LED_PON LED_1 LED_FL_OFF MAIN (SEE PAGE 3-1) LED_HDMI LED_HD KEY1 S601 S602 S603 S604 S605 . > X x H POWER 3 (SEE PAGE 3-11) 10 5 11 6 12 7 26 9 LED_FL_OFF LED_HDMI LED_HD LED_Blue LED_Blue 8 7 Q604 LED DRIVE D605 FL OFF 6 Q602 LED DRIVE D603 HDMI 5 Q603 LED DRIVE D604 HD 3 Q600 LED DRIVE +5V MODEL 1 IC601 REMOTO COMMANDER RECEIVER 27 IR 30 2 IR 10 05 3-5 3-6 1 OUT D601 (LED_Blue) BDP-S300/S301 3-4. POWER 1 BLOCK DIAGRAM POWER BLOCK MAIN BOARD (DB-BMB102) CN202 SW+12V 6, 7 4 CN201 SW+12V (A) 11 SW-12V (A) 9 EV+6V 6 11 9 6 SW+1.5V 3, 4 6, 7 2 4 SW+5V P_ON ~AC IN 2 3, 4 SWITCHING POWER SUPPLY CIRCUIT SW+3V 1 1 CN102 CN6002 SW+12V SW+3V SW+5V CN6051 SW+12V (A) SW-12V (A) EV+6V SW+1.5V P_ON Sub Microcomputer FU101 CN5701 1, 2 AC INLET CN203 SW+12V SW+5V 4 6 10 1 4 POWER 2 (SEE PAGE 3-9) SW+12V SW+5V BD-ROM DRIVE (BDV-102SO) CN3501 16 05 3-7 V–12A V+12A V+3D 3-8 V+5FL POWER 3 (SEE PAGE 3-11) BDP-S300/S301 3-5. POWER 2 BLOCK DIAGRAM AU-258 BOARD (SEE PAGE 4-5) CN001 V-12A POWER 1 (SEE PAGE 3-8) V+12A V+3D Q002 B- SWITCH 4 6 IC001 -9V REG. Q004 B+ SWITCH 10 Q005 SWITCH IC009 IC010 IC011 AMP AMP AMP IC008 AUDIO DAC IC007 AUDIO DAC IC006 AUDIO DAC IC002 +9V REG. IC003 +5V REG. IC004 GATE 05 3-9 3-10 BDP-S300/S301 3-6. POWER 3 BLOCK DIAGRAM FR-271 BOARD FL-176 BOARD (SEE PAGE 4-17) (SEE PAGE 4-13) POWER 1 (SEE PAGE 3-8) CN101 CN100 V+5FL CN600 8 15 V+5E 4 IC601 REMOTO COMMANDER RECEIVER D601 (LED Blue) D603 HDMI IC100 FL DRIVE VEE 30 D604 HD D605 FL OFF Q103 B+ SWITCH F100 T100, Q104,105 DC-DC CONVERTER F1 F2 Q101,102 SWITCHING D100 Q100 SW LED_PON FL/FR (SEE PAGE 3-5) LED_1 05 3-11 3-12E ND100 FLUORESCENT INDICATOR TUBE BDP-S300/S301 SECTION 4 SCHEMATIC DIAGRAMS AND PRINTED WIRING BOARDS 4-1. FRAME SCHEMATIC DIAGRAM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 JA4101 VIDEO OUT VIDEO S VIDEO A JA4201 COMPONENT VIDEO OUT AU-258 BOARD D 1 1 XMMUTE XAMUTE 2 2 XAMUTE GND 3 3 GND V-12A 4 4 V-12A GND 5 5 GND V+12A 6 6 V+12A GND 7 7 GND V+6E 8 8 V+6E GND 9 9 GND 10 10 V+3D GND 11 11 GND DAC_MUT 12 12 DAC_MUT E 13 13 27P CN6002 V+3D DAC_XCS_1 DAC_XCS_1 DAC_MC 14 14 DAC_MC DAC_MDI 15 15 DAC_MDI DAC_MDO 16 16 DAC_MDO GND 17 17 GND MCLK 18 18 MCLK GND 19 19 GND ABCLK 20 20 ABCLK ADATA5_0 21 21 ADATA5_0 MAIN BOARD (DB-BMB102) 1 CN202 8P 8P GND 1 SW+12V 2 PM-138 HARNESS 1 GND 2 SW+12V GND 3 3 GND SW+5V 4 4 SW+5V GND 5 5 GND SW+3V 6 6 SW+3V SW+3V 7 7 SW+3V GND 8 8 GND P_ON 1 1 P_ON ALRCK 22 22 ALARCK DAC_XRST 23 23 DAC_XRST DAC_XCS_2 24 24 DAC_XCS_2 GND 2 2 GND ADATA5_3 25 25 ADATA5_3 SW+1.5V 3 3 SW+1.5V ADATA5_2 26 26 ADATA5_2 SW+1.5V 4 4 SW+1.5V ADATA5_1 27 27 ADATA5_1 GND 5 5 GND EV+6V 6 6 EV+6V GND 7 7 GND A GND 8 8 A GND SW-12V (A) 9 9 SW-12V (A) A GND 10 10 A GND SW+12V (A) 11 11 SW+12V (A) 1 SW+12V(W) 2 GND 3 GND 4 SW+5V(W) CN201 11P CN6051 11P B TO B F 2 HARNESS CN101 2P CN5701 27P XMMUTE C AC-259 1 1 R CN001 2 2 R PB PR V++ WOOFER JA5501 COAXIAL L L GND R CENTER FAN HDMI OUT 3 Y 2P L B AC-Inlet CN4501 4 OPTICAL FRONT REAR CN6701 AUDIO OUT L DIGITAL OUT JA5502 N J001 5.1CH OUTPUT J003 PM-139 HARNESS PBD-003 G HARNESS CN203 POWER BLOCK V+13SW LED_Blue MODEL1 KEY0 5 4 3 IR LED_P ON 6 GND GND 1 LED_IOE 7 2 FLDC+ GND 8 FLDC- 9 GND 11 10 FL-29V 12 LED_HD 19 13 LED_HDMI 20 GND LED_FL_OFF 21 14 LED_LAN 22 V+5FL KEY1 23 GND LED_DDHD 24 15 GND 25 GND FLSTB 26 16 FLDATA 27 18 19 20 21 22 23 24 25 26 27 28 29 30 GND FLDC- GND FLDC+ LED_IOE GND LED_P ON V+13SW LED_Blue MODEL1 KEY0 GND IR 17 13 GND FL-29V 12 LED_HD 16 11 LED_HDMI GND 10 LED_FL_OFF 15 9 LED_LAN 14 8 KEY1 GND 7 V+5FL 6 5 FLSTB GND 4 LED_DDHD 3 2 GND FLCLK FLDATA GND CN100 30P 1 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 FFC 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 1 2 3 GND SW+12V(W) 4 GND 4P SW+5V(W) 17 GND 28 FML-003 MBD-003 HARNESS J 18 FLCLK 29 CN3501 GND 40 39 38 36 37 35 34 33 32 31 30 29 28 27 26 25 22 24 21 23 20 19 18 17 16 15 14 13 12 11 10 8 9 7 6 5 4 3 2 1 30 CN1802 40P 30P H I FR-271 BOARD CN101 11P BD-ROM DRIVE (BDV-102SO) K L M 4P FL-176 BOARD CN600 11P GND 1 11 GND IR 2 10 IR KEY0 3 9 KEY0 KEY1 4 8 KEY1 LED_FL_OFF 5 7 LED_FL_OFF LED_HDMI 6 6 LED_HDMI LED_HD 7 5 LED_HD V+5E 8 4 V+5E LED_Blue 9 3 LED_Blue GND 10 2 GND GND 11 1 GND FLR-011 FFC 4-2 05 4-1 FRAME SCHEMATIC DIAGRAM BDP-S300/S301 THIS NOTE IS COMMON FOR WIRING BOARDS AND SCHEMATIC DIAGRAMS (In addition to this, the necessary note is printed in each block) (For printed wiring boards) • b: Pattern from the side which enables seeing. (The other layers’ patterns are not indicated) • Through hole is omitted. • Circled numbers refer to waveforms. • There are few cases that the part printed on diagram isn’t mounted in this model. • Chip parts. Transistor Diode 6 5 4 4 5 6 C B E 4 5 1 3 2 1 2 3 3 2 1 3 2 1 5 4 3 2 3 1 2 3 1 2 1 (For schematic diagrams) • All capacitors are in µF unless otherwise noted. pF : µµF. 50V or less are not indicated except for electrolytics and tantalums. • All resistors are in ohms, 1/4 W (Chip resistors : 1 /10 W) un-less otherwise specified. kΩ=1000Ω, MΩ=1000kΩ. • Caution when replacing chip parts. New parts must be attached after removal of chip. Be careful not to heat the minus side of tantalum capacitor, because it is damaged by the heat. • All variable and adjustable resistors have characteristic curve B, unless otherwise noted. • 2: nonflammable resistor • 5: fusible resistor • C : panel designation • f : internal component. • C : adjustment for repair. • U : B+ Line • V : B– Line • Circled numbers refer to waveforms. • Voltages are dc between measurement point. • Readings are taken with a color-bar signals on Blu-ray disc. • Readings are taken with a digital multimeter (DC 10MΩ). • Voltage variations may be noted due to normal production tolerances. Note: The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Note: Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce por tant le numéro spécifié. When indicating parts by reference number, please include the board name. NOTE 4-3 4-4 BDP-S300/S301 4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS AU-258 (ANALOG AUDIO) SCHEMATIC DIAGRAM – Ref. No. : AU-258 board; 1,000 series – : Uses unleaded solder. • See page 2-4 for circuit boards location. 4 3 6 5 7 AU-258 BOARD 10 11 14 13 12 15 16 17 18 BB+ R103 R081 1.8k 0.5% 470p R084 12 13 14 B+ B+ B+ B+ B+ C020 47 25V C034 XX C058 10 50V C043 0.1 C035 AOUTRAOUTL+ AOUTR+ AGND C VCOM 11 12 13 14 2.5 1.4 5.1 B+ VCC L VCC F 3.3 DZFL MSEL 3.3 B+ 0 1.7 MDI MC 1.7 R134 680 0.5% R095 1.8k 0.5% C116 0.1 0 9 VCC 6 7 8 4 3 2 1 R079 XX B+ C061 10 50V C064 2.2 C054 0.1 100 R080 R149 47k 0.5% C123 0.1 R157 4.7k R163 100k C143 100p Q022 2SD2704K-T146 D015 XX MUTE R150 47k 0.5% C134 0.1 R096 1.8k 0.5% B+ R035 10k 0 Q023 2SD2704K-T146 MUTE R158 4.7k 0.7 R142 470 0.5% C144 100p D016 XX R169 470 0.5% 0 C129 47 63V C108 470p C080 1500p C078 XX C130 XX B- R135 680 0.5% 11.8 B+ B+ 9 0 0.9 VCC OUT -IN 0.9 +IN -IN OUT +IN 0 0.9 -IN OUT C133 0.1 +IN AGND R AOUTL- 10 R168 470 0.5% B+ 5 R132 3.3k 0.5% C107 470p R141 470 0.5% 0.7 C113 XX C106 470p R133 3.3k 0.5% C128 47 63V C105 470p 5.1 VCC R 9 1.4 AGND F 8 AGND L DGND 7 R075 XX SWITCH C112 XX R131 680 0.5% VCC C 1.4 1.4 5.1 3.3 3.3 6 DZFR 5 MDO 4 C048 0.1 Q008 MSB709-RT1 +IN R130 680 0.5% C079 1500p C077 XX 15 VDD 16 R065 XX -9 R031 10k C147 1 17 C044 XX R028 10k 18 3 R071 XX M 19 C045 47 25V 11.8 20 2 R059 XX B+ 21 X_RST 22 MCLK 23 MUTE 24 5.1 0 0 25 1 1.7 L 26 DATA B+ AUDIO DAC X_MS IC008 PCM1791ADBR 8 B+ IC008 27 BICK 28 LRCK 9 C005 0.1 AMP IC011 NJM4580MD-(TE2) R129 3.3k 0.5% B+ XX 0 1A VCC R058 C060 0.1 R094 1.8k 0.5% 3.3 1B 4B XX 3.3 4A 0 0 0 4Y 3B 3Y 3A 10 3.3 11 3.3 12 3.3 13 14 R176 0 R177 0 GATE IC004 SN74LVC08APWR XX C053 0.1 C047 0.1 R093 1.8k 0.5% 1.7 1Y 0 2A 0 2B 0 3.3 2Y 3.3 GND 3.3 7 6 5 4 3 2 1 K XX R064 IC011 C046 39 16V C024 XX R070 C122 47 63V B+ J R074 0.9 C063 2.2 B+ IC004 R167 470 0.5% 0.1 C052 47 25V D014 XX 9 C017 0.1 D004 XX R078 100 C023 XX C142 100p Q021 2SD2704K-T146 MUTE R140 470 0.5% C100 XX R118 3.3k 0.5% R088 1.8k 0.5% VCC C010 0.1 B+ B+ R073 XX R156 4.7k 0.7 C127 0.1 C088 470p OUT O R146 47k 0.5% R117 680 0.5% C074 1500p C068 XX +5V REG. G 1 0 R087 1.8k 0.5% R063 XX R069 XX 5.1 I 2 WOOFER B- 0 12.6 3 D013 XX Q020 2SD2704K-T146 MUTE R145 47k 0.5% C118 0.1 XX B+ D001 DAN202K-T-146 4 -9.1 2.5 1.4 VCC L 5.1 VCC F MDO MDI DZFL 3.3 R116 680 0.5% C141 100p CENTER C115 IC003 REAR 0.7 R R162 100k R155 4.7k 8 OUT 11 L 0 0 10 7 -IN VCOM 9 6 +IN AOUTR+ AGND C 8 VCC C AOUTRAOUTL+ 7 1.4 6 AGND L 5 R053 XX R007 22 FRONT AMP IC010 -VCC 5.1 1.4 1.4 5.1 3.3 3.3 4 DZFR 3 MSEL AGND R AOUTL- 15 VCC R 16 AGND F 17 DGND 18 5 0.9 R008 XX IC003 NJM78M05DL1A-TE1 R175 0 19 2 R057 XX B+ 20 L R R165 470 0.5% IC010 C087 470p IC002 NJM78M09DL1A(TE1) L001 XX I 21 VDD 22 X_RST 23 5.1 0 1.7 0 24 1 B+ -9 25 3.3 I Q004 2SB1561T100Q B+ SWITCH 26 MCLK 12.6 B+ 12.7 G 12.8 27 1.7 R012 10k H AUDIO DAC MUTE +9V REG. 28 IC007 C019 470 16V C016 0.1 0 C004 47 25V IC002 R115 3.3k 0.5% J001 B+ C098 XX C086 470p D012 XX C126 0.1 C085 470p R112 680 0.5% NJM4580MD-(TE2) DATA 12 B+ C009 0.1 C007 47 25V 0 R030 XX R019 10k C018 470 16V C015 0.1 MC -14.4 C008 0.1 C006 47 25V 3.3 R024 220k 1.7 R017 10k O G R114 3.3k 0.5% X_MS -9V REG. BICK IC001 -13.8 XX C140 100p R173 470 0.5% 0 R052 LRCK -14.4 R023 100k B+ -13.8 Q005 MSD601-RST1 SWITCH D002 1SS355TE-17 R011 10k R139 470 0.5% C121 47 63V C097 XX R113 680 0.5% D011 XX C139 100p C083 XX C095 470p C073 1500p C067 XX R056 XX D003 1SS355TE-17 C003 47 25V O COM R166 470 0.5% C120 47 63V R111 3.3k 0.5% R085 1.8k 0.5% B- -9.1 I 0 R138 470 0.5% R171 470 0.5% 0.9 -14.5 R154 4.7k R108 680 0.5% C109 0.1 R107 3.3k 0.5% R086 1.8k 0.5% IC007 PCM1791ADBR B- -14.4 -VCC -9.1 C057 0.1 R068 XX 1.7 -14.4 C096 XX R110 3.3k 0.5% 0.9 C050 0.1 C042 0.1 R062 XX B- B+ 0.9 C037 39 16V IC001 NJM79M09DL1A-TE1 MUTE 0.7 B+ R002 100 C022 XX F AMP C125 0.1 D008 XX Q019 2SD2704K-T146 IC009 C084 470p C072 1500p C066 XX 0.5% 1.8k 0.5% L002 XX R013 XX Q002 2SD1781K-T146-QR B- SWITCH 0.9 VCOM 2.5 1.4 B+ R077 100 R083 1.8k AUDIO OUT R C138 100p R109 680 0.5% C062 2.2 L D007 XX C137 100p IC009 NJM4580MD-(TE2) C056 10 50V J003 R170 470 0.5% R144 47k 0.5% B- B+ XX XX 22 XX 1 0.9 AOUTR+ AGND C R022 0 B- C055 0.1 5.1 AOUTRAOUTL+ VCC L 5.1 VCC F DZFL R072 XX R061 XX R003 R006 R004 R016 VCC C AGND R AOUTL- 14 B+ E 1.4 VCC R 13 1.4 AGND F 12 AGND L DGND 11 2 -IN 100 1.4 0 5.1 0 5.1 VDD 10 DZFR X_RST 9 R067 XX R178 C049 0.1 C040 0.1 C036 39 16V 0 0 8 3 OUT 27 7 4 -IN 26 ADATA5_1 6 8 +IN 25 ADATA5_2 5 7 -VCC 24 ADATA5_3 4 6 0.9 DAC_XCS_2 3 R161 100k R143 47k 0.5% C117 0.1 5 -9.1 23 2 R153 4.7k 0.7 B- DAC_XRST 1 R055 XX R018 22 15 0.1 22 16 XX 21 17 C110 20 ALRCK 18 C099 ABCLK ADATA5_0 C094 XX B- 19 0 R106 3.3k 0.5% XX 18 GND 19 Q018 2SD2704K-T146 MUTE C124 0.1 XX MCLK 20 C032 17 R051 XX R009 22 21 C051 0.1 16 GND AUDIO DAC R015 XX R001 XX 22 C033 47 25V D DAC_MDO R014 XX 23 3.3 15 24 3.3 14 25 B+ 13 DAC_MC DAC_MDI 26 C041 0.1 DAC_XCS_1 IC006 27 MSEL 12 B+ B+ MCLK DAC_MUT 28 B+ 1.7 11 IC006 PCM1791ADBR 9 10 GND 1.7 GND V+3D MDO 8 B+ MAIN BOARD (DB-BMB102) CN5701 R137 470 0.5% R105 680 0.5% C082 470p MUTE V+6E XX 0 7 XX MC 6 GND XX R054 R050 3.3 V+12A R060 1.7 B- B+ MDI 5 DATA 4 GND XX 1.2 V-12A R066 X_MS 3 BICK GND B+ LRCK 2 1.7 1 25 C119 47 63V 27P B+ C R104 680 0.5% C071 1500p C065 XX R082 1.8k 0.5% XAMUTE 24 C081 NO MARK:REC/PB MODE XMMUTE 23 3.3k 0.5% C093 -REF.NO.:1,000 SERIESXX MARK:NO MOUNT B 22 21 B+ AUDIO CN001 20 19 B- C114 A 9 8 5.1CH OUTPUT 2 XX 1 0.9 • • See page 4-7 for printed wiring board. R136 3.3k 0.5% C021 XX C027 XX 0 C030 XX C038 XX R089 XX 0.1 R029 47k Q014 MUN2213T1 SWITCH R090 XX R046 XX R172 XX C135 XX J002 XX Q024 R040 XX XX R159 XX R164 XX (Center) MSB709-RT1 C145 XX SWITCH 11.8 DGND AGND F VCC R 5 6 7 8 9 10 11 12 13 6 7 8 -IN OUT VCC VCC C 5 D010 XX IC012 XX R123 XX OUT VDD 4 15 -IN X_RST 3 16 VCOM MCLK 2 17 AOUTR+ AGND C MUTE 1 18 AOUTRAOUTL+ DATA VCC L 19 BICK DZFL 20 AGND R AOUTL- 21 AGND L 22 VCC F 23 MSEL MDO 24 DZFR 25 MDI 26 LRCK IC005 XX Q015 MUN2213T1 SWITCH 27 X_MS 28 MC 0 0.1 P D009 XX (Sub) 0 3.3 R021 47k R147 XX R036 10k Q007 DTC124TKA-T146 SWITCH Q001 MUN2213T1 MUTE DRIVE C101 XX R122 XX R042 XX Q009 11.1 0.1 3 R032 10k C148 1 R020 10k O 11.8 C089 XX C075 XX R044 XX 11.8 C131 XX R121 XX C069 XX +IN C002 1000 16V +IN 3.1 11.8 -VCC Q003 MUN2213T1 MUTE DRIVE C028 XX N 11.8 Q006 DTC124TKA-T146 SWITCH 0.1 4 3 2 1 C146 XX 14 11.8 Q013 C149 1 R034 10k MSB709-RT1 R010 XX R038 10k 0 Q011 DTC124TKA-T146 SWITCH Q R027 XX SWITCH 11.1 Q017 MUN2213T1 SWITCH R124 XX C090 XX C091 XX R091 XX R047 XX R048 3.3 R126 XX XX R005 XX R092 XX 0.1 C070 XX C076 XX C103 XX R152 XX R127 XX R128 XX Q12 XX C150 XX R151 XX C111 XX R041 XX R043 XX R045 XX 0 C102 XX Q025 XX R160 XX C136 XX C092 XX C104 XX R174 XX R148 XX C132 XX R033 XX SIGNAL PATH R049 100 R037 XX R AUDIO SIGNAL Q016 XX Q010 XX 05 R039 XX C039 XX C025 XX R125 3.3k PB C029 C026 XX XX 4-5 C059 XX C031 XX 4-6 ANALOG AUDIO AU-258 BDP-S300/S301 AU-258 BOARD (SIDE A) IC004 IC006 IC007 IC008 H-11 C-7 D-7 F-7 Q006 Q007 Q008 Q009 Q011 Q013 G-11 G-11 I-11 I-11 G-12 H-12 AU-258 (ANALOG AUDIO) PRINTED WIRING BOARD – Ref. No. : AU-258 board; 1,000 series – There are a few cases that the part isn't mounted in this model is printed on this diagram. : Uses unleaded solder. • See page 2-4 for circuit boards location. AU-258 BOARD (SIDE A) R039 A R016 R007 R050 + C036 C040 C062 C055 R154 C 15 1 IC006 R003 R002 R005 C022 14 R004 C051 R178 R009 B R015 R051 R010 R022 R055 R027 R061 R014 C041 R001 R067 R077 R072 R006 R018 28 R054 R060 R161 R066 C049 R078 R073 R063 R030 R069 R153 C043 R057 R053 C052 D R052 + IC007 C037 15 1 C042 C063 R162 C057 R156 C023 14 R056 28 R062 R068 R155 C050 R079 R158 C048 R071 R075 R080 R065 R059 C054 IC008 15 R058 + R064 28 R070 R074 R043 Q011 R041 C031 R177 R176 R040 Q006 Q007 ECB EC B ECB C150 C149 + R046 C030 14 8 IC004 1 7 C147 R031 C148 R036 R044 R035 R042 28 C005 IC005 C027 15 1 C028 C059 H 14 C038 R159 C021 R032 BC E R045 Q010 C029 R164 R047 R049 R048 G R034 EC B R037 R160 C053 R038 C064 1 R157 C060 F 14 C046 C024 R163 C047 E R033 ECB Q012 Q013 I 05 ANALOG AUDIO AU-258 1 2 3 4-7 4 5 6 7 8 9 10 4-8 ECB ECB Q008 Q009 11 12 1-873-157- 11 BDP-S300/S301 AU-258 BOARD (SIDE B) 1 27 CN001 A R123 R122 C140 C139 D014 D011 J001 R C141 C144 C143 IC012 C145 C E R147 8 C089 G R172 B H C131 C135 1-873-157- 11 R121 I 05 12 11 10 9 4-9 8 7 6 5 4 3 2 4-10 L CENTER AU-258 BOARD (SIDE B) Q024 R151 1 F J002 ECB R152 R141 C132 Q025 C146 R174 C133 C112 C128 5.1CH OUTPUT WOOFER D009 D010 E REAR E D015 D016 D013 R165 C R149 B C136 5 L D R168 C123 Q022 R148 4 R169 R150 C134 ECB R142 8 C104 C103 C102 C111 C091 C090 C070 C076 R125 R126 C142 R171 R146 R145 C126 E C101 R089 C075 R090 R124 C039 R167 C127 C118 C115 C129 R127 C069 C025 R091 R173 R144 R143 C124 C093 C100 B C Q023 1 C105 C092 D012 R170 C125 C117 C094 C099 C110 C098 C114 C116 5 FRONT R139 IC011 C113 C106 R128 R092 R029 BCE 4 C130 C026 B CE C108 R129 C002 Q014 C097 C073 R093 Q015 ECB C Q020 C121 R135 R130 R131 C138 C096 C083 C107 C078 C080 R133 C079 R175 BCE 8 C085 R134 C077 R094 R028 BCE 5 Q021 R140 IC010 R136 R132 C061 ECB R020 R021 Q017 C095 C086 R114 C020 R095 O Q003 C122 1 R112 R096 C044 I 4 C045 IC003 L R Q018 BC E C088 R111 D001 Q016 C119 R117 R113 C067 L001 C017 R085 C010 C087 C074 R115 C019 C058 R116 O R086 D004 C068 R118 Q019 ECB R137 C034 D003 IC002 I Q004 C016 C007 R008 C009 C ECB 8 C081 R088 R012 Q001 R138 R103 R087 B 5 R104 R105 1 C035 C004 E C082 R106 C071 R081 4 IC009 C065 L002 O R082 C018 I D002 R023 IC001 C015 C006 ECB R024 BC E Q005 R013 C003 R017 R019 C008 Q002 R011 R108 AUDIO OUT B R109 C109 C056 C084 C120 R107 C032 C072 R083 C066 R084 R J003 R110 C137 R166 C033 D007 D008 2 26 1 D001 D002 D003 G-11 C-10 D-10 IC001 IC002 IC003 IC009 IC010 IC011 C-10 D-11 E-11 B-4 D-4 F-4 Q001 Q002 Q003 Q004 Q005 Q014 Q015 Q017 Q018 Q019 Q020 Q021 Q022 Q023 G-12 B-11 G-11 D-12 C-12 H-11 H-11 H-12 C-2 C-2 E-2 D-2 F-2 F-2 ANALOG AUDIO AU-258 BDP-S300/S301 FL-176 (FL/LED) PRINTED WIRING BOARD – Ref. No. : FL-176 board; 2,000 series – There are a few cases that the part isn't mounted in this model is printed on this diagram. : Uses unleaded solder. • See page 2-4 for circuit boards location. FL-176 BOARD FB003 S100 R116 R118 R123 R122 BCE R103 4 R105 R121 C124 JW104 R101 F100 R110 T100 JW116 C113 C114 42 4 C104 2 1 Q105 C118 C119 D105 JL107 JW111 Q104 D 05 8 L102 ECB Q101 Q102 E CB 1 Q103 D103 ECB 44 R104 R124 D100 Q100 JL106 45 R125 C108 2 23 2 JW114 C116 D104 D102 D101 JL105 R102 R119 R120 JW105 C102 C117 JW113 C120 ND100 R126 5 R112 12 IC100 R113 JW115 JW110 C111 JW102 JW117 JW109 C101 JL108 11 JL101 C112 JL102 JW121 1 R109 33 34 R117 C123 JW112 CN101 R106 C106 JL104 R111 R107 R115 JL109 C109 JW101 C110 C107 2 C C115 JL103 R114 R100 1 44 JW108 JW120 R108 10 11 JW119 JW107 JW106 JL100 29 30 CN100 2 JW122 JW118 JW103 1 C100 L101 A C105 FB004 B 1 FB001 FB002 E CB 1 2 3 4 5 6 7 8 9 10 1-873-142- 11 FL-176 BOARD FL/LED FL-176 4-11 4-12 CN101 C-1 D100 D101 D102 D103 D104 D105 B-9 C-9 C-9 C-9 C-8 C-7 IC100 C-4 Q100 Q101 Q102 Q103 Q104 Q105 B-9 B-9 B-9 B-10 D-10 D-10 BDP-S300/S301 FL-176 (FL/LED) SCHEMATIC DIAGRAM • See page 4-11 for printed wiring board. – Ref. No. : FL-176 board; 2,000 series – 1 3 2 4 5 6 7 9 8 12 11 14 13 15 16 17 ND100 FLUORESCENT INDICATOR TUBE FL-176 BOARD A 10 INDICATOR DRIVE 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 C104 F2 F2 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 NC NC NC NC NC NC NC NC NC 9 NC 8 NC 6G 7 NC 5G 6 11G 4G 5 10G 3G 4 9G 2G 2 8G 1G 1 7G F1 NO MARK:REC/PB MODE F1 -REF.NO.:2,000 SERIESXX MARK:NO MOUNT 44 45 XX S[1] S[2] S[3] S[4] S[5] S[6] S[7] S[8] S[9] S[10] S[11] S[12] B+ C B+ B+ R117 10k JL104 COM[2] COM[3] COM[4] COM[5] COM[6] COM[7] COM[8] -21.4 -21.4 -21.4 -21.4 -21.4 -21.4 -21.4 VDD GRID1 GRID2 GRID3 GRID4 GRID5 GRID6 GRID7 GRID8 GRID9 -15.4 -17.4 -15.4 S[7] S[8] S[9] SEG9 -17.2 S[6] SEG8 -15.4 S[5] SEG7 -23.1 S[4] SEG6 -23.1 S[3] SEG5 -21.2 S[2] SEG4 -21.2 S[1] SEG3 SEG10 SEG2 KEY2 SEG1 SEG11 22 24 KEY1 21 23 LED_P ON SEG12 20 22 GND STB 19 21 LED_ICE SEG13 CLK 18 20 FLDC+ SEG14 17 19 DIN 15 18 GND SEG15 IC100 PT6315 16 17 GND FLDC- SEG16 FL DRIVE 14 FL-29V IC100 13 16 DOUT 12 GND C110 XX C107 XX CSC 4.9 15 5 VSS 4.9 C106 XX B+ JL101 VEE 10 11 V+5FL 14 47 LED4 VDD R106 GRID12 33 32 31 30 29 28 27 26 25 24 23 13 5 34 GND 5 JL102 35 R107 47 36 12 GRID11 LED3 9 11 LED_HD GRID10 LED2 8 LED_HDMI JL103 37 R108 47 LED1 7 -21.4 COM[9] -21.4 COM[10] -21.4 COM[11] C123 0.01 R116 XX R118 8.2k R123 8.2k R119 12k R124 12k R125 12k S100 C124 0.01 / -23.6 -23.1 S[16] -19.3 S[15] -17.3 S[14] -23.1 S[13] -23.1 S[12] -23.1 S[11] -13.4 S[10] JL109 V+13SW 25 LED_Blue 26 MODEL1 27 KEY0 28 GND 29 1 GND IR 30 2 IR 3 KEY0 4 KEY1 5 LED_FL_OFF 6 LED_HDMI 7 LED_HD 8 V+5E 9 LED_Blue C116 XX B+ G 2.8 JL100 38 9 10 39 LED_LAN LED_FL OFF GND MAIN BOARD (DB-BMB102) CN3501 R111 100k 8 40 KYE1 41 7 6 6 5 GND LED_DDHD R114 XX 4 5 3 4 R126 33k 2 3 FLSTB 42 2 GND 43 FLCLK FLDATA R115 XX C115 0.1 44 1 C112 XX C111 XX R113 10k 1 E GND C109 XX C102 0.1 C101 100 16V C100 XX 30P VSS CN100 R121 1.8k B+ COM[1] B+ -21.4 B+ R109 0 D R120 10k R122 2.2k R100 0 B+ F S[13] S[14] S[15] S[16] COM[11] COM[10] COM[9] COM[8] COM[7] COM[6] COM[5] COM[4] COM[3] COM[2] COM[1] B CN101 11P H FR-271 BOARD CN600 (SEE PAGE 4-17) B+ 4 2 1 R103 22k R110 1.8k Q103 RSS040P03FD5TB B+ SWITCH R104 22k C105 0.022 2 10 3 1 C113 0.01 C108 100 16V 4 7 D101 1SS355TE-17 C114 XX D102 1SS355TE-17 JL106 C119 0.1 0 2.7 0 D100 DAN202UT106 2.4 0 FB002 FB003 K FB004 -0.4 Q100 DTC114YKA-T146 SWITCH 5 8 6 9 JL107 2.7 Q102 FB001 GND JL105 D104 1SS355TE-17 4.8 -0.4 R105 22k J Q104 2SC2411K-T-146-CR DC-DC CONVERTER 4.9 8 4.9 R101 10k D103 1SS355TE-17 4.9 7 4.9 L101 XX GND 11 4.9 6 4.9 10 D105 MM3Z5V6ST1 B+ L102 47uH 5 4.9 3 B+ I 0 R102 0 F100 0.5A 32V DTC124EKA-T146 SWITCHING 0 Q105 2SC2411K-T-146-CR DC-DC CONVERTER T100 DC-DC CONVERTER TRANSFORMER Q101 DTC124EKA-T146 SWITCHING C117 22 C118 0.1 R112 27k C120 0.1 JL108 05 4-13 Note: The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Note: Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce por tant le numéro spécifié. 4-14 FL/LED FL-176 BDP-S300/S301 FR-271 (SW/IR, INPUT/LED) PRINTED WIRING BOARD – Ref. No. : FR-271 board; 2,000 series – There are a few cases that the part isn't mounted in this model is printed on this diagram. : Uses unleaded solder. • See page 2-4 for circuit boards location. FR-271 BOARD A A R611 R607 S604 S602 S601 R609 R606 R608 X G JW607 x . S605 R610 S603 R612 S600 B R630 ECB JL602 1 2 VCC O C605 JW605 JL605 C603 JW610 Q600 R604 JL601 E CB D601 JL603 (LED Blue) R631 JW611 D CN600 C600 IC601 10 HDMI 11 D603 HD JW606 D604 FL OFF C602 D605 R602 C JL600 JW602 ECB JW601 JL606 JW609 ECB R614 Q602 JW603 R615 Q603 R616 JW604 Q604 R629 R628 JL607 JW608 > D606 1-873-143- 11 1 05 2 3 4 5 6 7 8 9 FR-271 BOARD CN600 C-11 D601 D603 D604 D605 D-11 C-5 C-4 C-2 IC601 C-8 Q600 Q602 Q603 Q604 D-10 C-5 C-3 C-2 SW/IR, INPUT/LED FR-271 4-15 4-16 10 11 BDP-S300/S301 FR-271 (SW/IR, INPUT/LED) SCHEMATIC DIAGRAM – Ref. No. : FR-271 board; 2,000 series – 1 • See page 4-15 for printed wiring board. 3 2 4 5 6 8 7 FR-271 BOARD A LED DRIVE, FUNCTION KEY -REF.NO.:2,000 SERIESXX MARK:NO MOUNT NO MARK:REC/PB MODE S600 CN600 B R606 1.8k 11P GND 1 GND 2 LED_Blue 3 V+5E 4 LED_HD 5 LED_HDMI 6 LED_FL_OFF 7 IC601 B+ FL-176 BOARD CN101 (SEE PAGE 4-14) REMOTE COMMANDER RECEIVER JL601 IC601 GP1UM28XK0SF B+ 4.9 VCC 4.9 C R609 2.2k JL602 KEY1 8 OUT KEY0 9 GND IR 10 GND 11 R607 8.2k R610 8.2k R608 12k R611 12k R612 12k JL603 R602 47 B+ C600 XX JL600 C602 0.1 B+ S602 S603 S604 S605 C603 XX C605 47 16V S601 JL607 JL606 B+ JL605 D B+ B+ R604 82 R631 XX B+ R615 330 R614 330 R616 330 (LED Blue) HDMI D601 NSPW-310BST-A0S D606 XX 4 0 R628 XX 0 Q600 MUN2211T1 LED DRIVE R629 XX D605 SLI-343YC D604 SLI-343YC E 3.1 FL OFF HD D603 SLI-343YC 4 Q602 MUN2211T1 LED DRIVE 0 R630 XX 4 Q603 MUN2211T1 LED DRIVE 0 Q604 MUN2211T1 LED DRIVE 05 4-17 4-18 SW/IR, INPUT/LED FR-271 BDP-S300/S301 MEMO 4-20E Main Set, Power Supply Section Flowchart No.1 Power does not turn on Does the power turn on by the Power button of remote controller and main set? No For the remote controller, see Operation and Display section, Flowchart No.1 “Disabled operation from remote controller” Yes No Is the fuse in each line on power board OK? FU101 on primary side CN6051 6pin 6V 5-1 6V P301 3V P401 12V P202 1.5V P501 5V P302 Yes Yes Check/replace the power harnesses (PM-138, PM-139) If not improved by replacement, replace the Power board Is 5V supplied to connector CN100 15pin on FL board? No No Replace the Main board and Power Board SECTION 5 TROUBLESHOOTING Is the power supplied to connector CN6051 on main board? For the Power button of main set, see Operation and Display section, Flowchart No.2 “Disabled key operation” Check/replace the FL board flexible cable (MAIN h FL). If not improved by replacement, replace the Main board. Yes Check/replace the FL board flexible cable (MAIN h FL). If not improved by replacement, replace the Main board. BDP-S300/S301 Main Set, Power Supply Section Flowchart No.2 The set does not start normally by power ON Is about 5V supplied to connector CN100 28pin (=Key 0) on FL board when Power key on the set is pressed? No Is the symptom improved by replacingthe Power switch? No See FL board flowchart 1 Yes Yes Is the error code “∗∗∗ ERR” displayed on FL tube? Replace the Power switch Displayed Replace the Main board Not displayed Is 5V supplied to connector CN6051 1pin on main board by power ON? No Go to Flowchart No.1 “Power does not turn on” 5-2 Yes Is respective voltages supplied to connector CN6021 & CN6051 on main board? CN6002 6pin 3V CN6002 4pin 5V CN6002 2pin 12V CN6051 11pin 12.5V CN6051 9pin -15V CN6051 3pin 1.5V No Is the fuse in each line on power board OK? 3V 5V 12V 12.5V -15V 1.5V P401 P302 P202 P401 P601 P501 Yes Yes Replace the Main Board Check/replace the power harness (PM-138, PM-139). If not improved by replacement, replace the Power board. No Replace the Power board. If not improved by replacement, replace the Main board. Main Set, Power Supply Section Flowchart No.3 Drive does not operate normally Are 12V and 5V supplied to the drive? No Is P303 fuse (5V) on power board OK? Yes Yes Check/replace the power harnesses (PBD-003). If not improved by replacement, replace the Power board Is ATAPI reset? Is connector CN1802 1pin on main board “H”? 5-3 Check/replace the drive flexible cable (MBD-003). If not improved by replacement, replace the Drive. If not still improved by replacement, replace the Main board. No Replace the Main board No Replace the power board. If the fuse blows again, 5V system in drive is faulty. Replace the drive Main Set, Power Supply Section Flowchart No.4 Video is not displayed normall Is the display of FL tube/LED normal? Yes Replace the Main board No Go to Flowchart No.2 “The set does not start normally by power ON” 5-4 Main Set, Power Supply Section Flowchart No.5 Audio is not heard normally No Go to Flowchart No.2 ‘‘The set does not start normally by Power on’’ Display on FL tube/LED normal? Yes No Is the audio signal present to digital output (HDMI/Coax/SPDIF) ? Replace the Main board Yes 5-5 Are audio digital signals output to connector CN5701 on Main board? CN5701 27pin ADATA32 CN5701 26pin ADATA22 CN5701 25pin ADATA42 CN5701 22pin ALRCK2 CN5701 21pin ADATA12 CN5701 20pin ABLCK2 CN5701 18pin AMCLK2 No Replace the Main board Yes Are control signals output to connector CN5701 on Main board? CN5701 23pin DAC_RST# CN5701 16pin DAC_MDO CN5701 15pin DAC_MDI CN5701 14pin DAC_MC CN5701 13pin DAC_CS# CN5701 12pin DAC_MUT CN5701 2pin XAMUTE CN5701 1pin XMMUTE Yes Proceed to ‘‘Audio board flowchart’’ No Replace the Main board Main Set, Power Supply Section Flowchart No.6 Video is not played back normally Try to play CD (YEDS-18), DVD (HLX-504 or HLX-505) and BD (BLX-104) respectively. Is any one played back normally? Yes Check/replace the drive flexible PWB (MBD-003). If not improved by replacement, replace the Drive If not improved by replacement, replace the Main board No Go to Flowchart No.3 “Drive does not operate normally” 5-6 Main Set, Power Supply Section Flowchart No.7 Audio is not played back normally Does the drive operate normally? No See Flowchart No.3 ‘‘Drive does not operate normally’’ in this section Yes No Audio present to Digital OUT (HDMI/COAXIAL/SPDIF)? Replace the Main board Yes 5-7 Audio digital signals outputted to connector CN5701 on Main board? CN5701 27pin ADATA32 CN5701 26pin ADATA22 CN5701 25pin ADATA42 CN5701 22pin ALRCK2 CN5701 21pin ADATA12 CN5701 20pin ABLCK2 CN5701 18pin AMCLK2 No Replace the Main board Yes Control signals outputted to connector CN5701on Main board? CN5701 23pin DAC_RST# CN5701 16pin DAC_MDO CN5701 15pin DAC_MDI CN5701 14pin DAC_MC CN5701 13pin DAC_CS# CN5701 12pin DAC_MUT CN5701 2pin XAMUTE CN5701 1pin XMMUTE Yes Proceed to ‘‘Audio board flowchart’’ No Replace the Main board Main Set, Power Supply Section Flowchart No.8 Fan does not rotate Is about 8V supplied to connector CN6701 1pin on Main board? No EV+12V supplied to connector CN6002 2pin on Main board? Yes Replace the Fan No Is P202 fuse on Power board OK? Yes Replace the Main board Yes Replace the Power board No Replace the Power board 5-8 Operation & Display Section Flowchart No.1 Disabled operation from remote controller Operation from remote controller is disabled though operation is enabled from a key on main set Is the power turned on by Power ON button of remote controller? NO Replace the Main board Yes Is “L” pulse signal input to CN100 30pin on FL board when operating remote controller? 5-9 Yes Check/replace the FL board flexible cable (MAIN h FL). If not improved by replacement, replace the Main board. No Is “L” pulse signal input to CN101 2pin on FL board when operating remote controller? Yes Conductor from CN101 2pin to CN100 30pin on FL board is broken. NO Symptom improved after FR board was replaced? Yes Check peripheral parts of IC601 (light receiver from remote controller) on FR board. If faulty, replace the FR board. No Replace the FL board flexible cable (FLR-011) Operation & Display Section Flowchart No.2 Disabled key operation Are the specified voltages output to connector CN100 8 and 28 pins on FL board when each button is pressed? Power Key0=28pin: 4.06~4.49 [V] Open/Close Key0=28pin: 1.36~1.50 [V] Play Key1=8pin: 3.43~3.79 [V] Pause Key1=8pin: 2.13~2.35 [V] Stop Key1=8pin: 2.78~3.07 [V] Previous Key1=8pin: 0.72~0.80 [V] Next Key1=8pin: 1.36~1.50 [V] Yes Check/replace the FL board flexible cable (MAIN h FL). If not improved by replacement, replace the Main board. No Symptom improved if FR board is replaced? Yes No Symptom improved if FL board flexible cable (FLR-011) is replaced? Yes Replace the FR board Replace the FL board flexible cable (FLR-011) 5-10 Reference: Relation between buttons and voltages KEY Specified voltages [v] SPEC CENTER KEY1 KEY0 0 0 0.76 PREVIOUS 0.72~0.80 NEXT OPEN/CLOSE 1.36~1.50 1.43 2.13~2.35 2.24 PAUSE 2.78~3.07 2.92 STOP 3.43~3.79 PLAY 3.61 P_ON 4.06~4.49 4.27 No FL board flowchart 2 Operation & Display Section Flowchart No.3 FL display tube does not light Is 2V voltage supplied to connector CN100 24pin on FL board? No Check/replace the FL board flexible cable (MAIN h FL). If not improved by replacement, replace the Main board. No Check/replace the FL board flexible cable (MAIN h FL). If not improved by replacement, replace the Main board. No Check/replace the FL board flexible cable (MAIN h FL). If not improved by replacement, replace the Main board. Yes Is 0V voltage supplied to connector CN100 10pin on FL board? Yes Are STB, CLK and DIN signals input to connector CN100 2, 4, 5 pins on FL board? 5-11 CN100 5pin STB CN100 2pin CLK CN100 4pin DATA Yes FL board flowchart 3 Operation & Display Section Flowchart No.4 LED does not light up 5V voltage supplied to connector CN100 15pin on FL board? 3.3V voltage supplied to connector CN100 on FL board? CN100 CN100 CN100 CN100 CN100 No No Check/replace the FL board flexible cable (MAIN h FL). If not improved by replacement, replace the Main board. Check/replace the FL board flexible cable (MAIN h FL). If not improved by replacement, replace the Main board. 24pin Power button 26pin Blue HD 12pin HD 11pin HDMI 10pin FL OFF Does the LED on FR board light up? No 5-12 Check LED peripheral parts on FL board. If faulty, replace the FL board. Yes No Symptom improved if FR board is replaced? Yes Check LED peripheral parts on FR board. If faulty, replace the FR board. Replace the FL board flexible cable (FL h FR). Audio Section No Is each power supplied to Audio board? CN001 CN001 CN001 CN001 24pin 22pin 20pin 18pin Replace the Main board -12V +12V +6V +3V Yes Check the power circuits on Audio board No Check the circuits on input side of IC001, 002, 003 IC003 INPUT pin 12V IC002 INPUT pin 12V IC001 INPUT pin -12V Yes No 5-13 Check the outputs of each Reg IC IC003 OUTPUT pin 5V IC002 OUTPUT pin 10V IC001 OUTPUT pin -10V Check the output of IC006, 007, 008 Check the output and peripheral circuits of IC009, 010, 011 Check the circuits on output side of IC001, 002, 003 FL Section Flowchart No.1 Inactive Power button on main set Yes Is the symptom improved by replacing the FL board? No Replace the Main board Yes Does the potential of CN100 28pin (Key 0) change to around 4.3V when Power button is pressed? Yes Key 1 line is broken. Replace the FL board. No Check the FL-MAIN flexible cable 5-14 FL Section Flowchart No.2 Inactive keys on main set Yes Symptom improved if FL board is replaced? No Replace the Main board Yes Which line of keys is inactive? Key 0 t Go to “Key 0 is inactive” Key 1 t Go to “Key 1 is inactive” Key 0 is inactive (Power button is active) Is about 5V present in CN100 28pin without pressing a key? No Check 5V line, R117 periphery and conductors on the FL board. If faulty, replace the FL board. No Check the resistors and conductors on Key 0 line. If faulty, replace the FL board. No Check 5V line, R120 periphery and conductors on the FL board. If faulty, replace the FL board. No Check the resistors and conductors on Key 1 line. If faulty, replace the FL board. Yes 5-15 Does the potential of CN100 28pin (Key 0) change when CN101 3pin and 1pin are short-circuited? Yes Check resistance of resistors on Key1 line. Also, check peripheral conductor patterns. Key 1 is inactive Is about 5V present in CN100 28pin without pressing a key? Yes Does the potential of CN100 8pin (Key 1) change when CN101 4pin and 1pin are short-circuited? Yes Check resistance of resistors on Key1 line. Also, check peripheral conductor patterns. Reference: Relation between buttons and voltages KEY Specified voltages [v] SPEC CENTER KEY1 KEY0 0 0 0.76 PREVIOUS 0.72~0.80 OPEN/CLOSE NEXT 1.36~1.50 1.43 2.13~2.35 2.24 PAUSE 2.78~3.07 2.92 STOP 3.43~3.79 PLAY 3.61 P_ON 4.06~4.49 4.27 FL Section Flowchart No.3 FL tube does not light Yes No Is about 5V applied to F100? Go to “FL tube switch periphery check” Yes Is about -24V applied to JL105? No Check the FL tube DD converter peripheral circuits. If faulty, replace the FL board. Yes No Is 5V applied to IC100 43pin? Check the 5V line on FL board. Yes No Does the IC100 5pin oscillate? 5-16 Replace the IC100. If not effective, replace the FL board. Yes Are the pulses input to IC100 7, 8, 9 pins? Yes Check the wiring between FL tube and IC100. If OK, replace the IC100. If not effective, replace the FL board. No Replace the FL-MAIN FFC. If not effective, replace the Main board. FL Section Flowchart No.4 FL tube switch periphery check Is the potential of Q103 1, 2, 3 pins 5V? No Check the 5V line on FL board. Yes Is the potential of Q103 4pin around 0V? No No Is the Q102 base voltage about 3V? Yes Yes Replace the Q103 No Is the Q101 base voltage 0V? Yes Replace the Q102 Replace the Q101 5-17 No No Is the CN100 10pin 0V? Does the CN100 10pin become 0V when Dimmer button on remote controller is pressed several times? Yes Yes Replace the Main board Is the Q100 24pin about 3V? Yes Replace the Q100 No Replace the Main board No Dimmer has effect only MEMO 5-18E BDP-S300/S301 SECTION 6 REPAIR PARTS LIST 6-1. EXPLODED VIEWS NOTE: • -XX and -X mean standardized parts, so they may have some difference from the original one. • Color Indication of Appearance Parts Example: KNOB, BALANCE (WHITE) . . . (RED) ↑ ↑ Parts Color Cabinet's Color • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. 6-1-1. • The mechanical parts with no reference number in the exploded views are not supplied. • Accessories and packing materials are given in the last of the electrical parts list. • Abbreviation AUS : Australian model CND : Canadian model E32 : Latin American model RUS : Russian model SP : Singaporean model TH : Thai model The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiquens pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. CASE ASSY A001 5 not supplied 7 4 5 main chassis block 3 2 1 Ref. No. 1 1 2 2 3 4 5 7 Part No. Description Ref. No. Remark X-2177-651-1 PANEL ASSY, FRONT (S300BJ/S300BJP/S300BM) X-2178-128-1 PANEL ASSY, FRONT (S301BJ/S301BM) X-2177-652-1 COVER ASSY, TRAY (S300BJ/S300BJP/S301BJ) X-2186-585-1 COVER ASSY, TRAY (S300BM/S301BM) 2-686-188-02 PLATE, BD INDICATION 7 4-942-568-41 EMBLEM (NO.5), SONY 3-070-883-71 SCREW, TAPPING A-1267-558-A CASE BLOCK ASSY (SERVICE USE SKZ) (S300BJ/S300BJP/S301BJ) A001 6-1 A001 A001 Part No. Description Remark A-1313-101-A CASE BLOCK ASSY (SERVICE USE SOEM) (S300BM/S301BM) 1-479-848-31 REMOTE COMMANDER (RMT-B101A) (S300BJ/S300BJP/S300BM: US, CND/ S301BJ/S301BM) 1-479-848-41 REMOTE COMMANDER (RMT-B101A) (S300BM: E32) 1-480-207-21 REMOTE COMMANDER (RMT-B101P) (S300BM: AEP, UK, RUS, SP, TH, AUS) 6-1-2. MAIN CHASSIS BLOCK 51 58 55 #1 51 not supplied 53 #1 54 not supplied 51 56 not supplied 57 59 not supplied (FL-176 board) 51 51 not supplied main block 51 not supplied (FR-271 board) Note: Please install it when Ref. No. 58 or 59 parts have not adhered when drive is exchanged. Please refer to SERVICE NOTE for the installation method. The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Note: Please use A-1337-670-A for BD drive with priority. (US, CND) Ref. No. Part No. 51 * 53 * 54 3-077-331-01 +BV3 (3-CR) 4-099-553-01 REUSE CLAMP 1-965-333-11 HARNESS (MBD-003) (S300BJ/S300BJP/S301BJ) 1-965-684-11 HARNESS (MBD-007) (S300BM: US, CND/S301BM) 1-965-688-11 HARNESS (MBD-008) (S300BM: AEP, UK, RUS, E32, SP, TH, AUS) * 54 * 54 0 55 55 Description Remark Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. Ref. No. Part No. Description 0 55 0 55 0 55 0 55 A-1337-677-A A-1337-678-A A-1382-235-A A-1382-236-A DRIVE (SOEM (SERVICE USE R2)) (AEP, UK) DRIVE (SOEM (SERVICE USE R4)) (AUS) DRIVE (SOEM (SERVICE USE R3)) (SP/TH) DRIVE (SOEM (SERVICE USE R5)) (RUS) 56 57 58 59 #1 1-787-625-21 3-077-331-31 3-087-220-01 2-348-685-01 7-682-544-09 FAN, DC +BV3 (3-CR) TAPE, NON-HALOGENE SPRING, EARTH (FRONT) +B 3X3 A-1337-670-A DRIVE (P (SERVICE USE R1)) (US, CND) A-1337-673-A DRIVE (SKZ (SERVICE USE R1)) (US, CND) 6-2 Remark 6-1-3. 103 MAIN BLOCK not supplied (AU-258 board) 103 102 102 not supplied not supplied 101 103 not supplied 105 not supplied 108 108 #1 not supplied 109 not supplied The components identified by mark 9 contain confidential information. Strictly follow the instructions whenever the components are repaired and/or replaced. Note: Please install it when Ref. No. 109 part have not adhered when drive is exchanged. Please refer to SERVICE NOTE for the installation method. Les composants identifiés par la marque 9 contiennent des informations confidentielles. Suivre scrupuleusement les instructions chaque fois qu’un composant est remplacé et / ou réparé. The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Ref. No. 101 102 103 Part No. Description 1-834-107-11 CABLE, FLEXIBLE FLAT (FML-003) 3-087-220-01 TAPE, NON-HALOGENE 3-077-331-01 +BV3 (3-CR) Remark Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. Ref. No. Part No. 0 105 1-474-057-41 POWER BLOCK (ZSSR641GA) (US, CND) 0 105 1-474-057-51 POWER BLOCK (ZSSR641IA) (AEP, UK, RUS, SP, TH, AUS) 3-077-331-31 +BV3 (3-CR) 3-274-166-01 GASKET, REAR 7-682-544-09 +B 3X3 108 109 #1 6-3 Description Remark AU-258 6-2. ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. • -XX and -X mean standardized parts, so they may have some difference from the original one. • RESISTORS All resistors are in ohms. METAL: Metal-film resistor. METAL OXIDE: Metal oxide-film resistor. F: nonflammable Ref. No. Part No. The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • SEMICONDUCTORS In each case, u: µ, for example: uA. . : µA. . uPA. . : µPA. . uPB. . : µPB. . uPC. . : µPC. . uPD. . : µPD. . • CAPACITORS uF: µF • COILS uH: µH Description Remark Ref. No. AU-258 BOARD, COMPLETE (Ref. No. 1000 Series) *********************** < CAPACITOR > C002 C003 C004 C005 C006 1-126-767-11 1-126-947-11 1-126-947-11 1-107-826-11 1-126-947-11 ELECT ELECT ELECT CERAMIC CHIP ELECT 1000uF 47uF 47uF 0.1uF 47uF 20% 20% 20% 10% 20% 16V 35V 35V 16V 35V C007 C008 C009 C010 C015 1-126-947-11 1-107-826-11 1-107-826-11 1-107-826-11 1-107-826-11 ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 47uF 0.1uF 0.1uF 0.1uF 0.1uF 20% 10% 10% 10% 10% 35V 16V 16V 16V 16V C016 C017 C018 C019 C020 1-107-826-11 1-107-826-11 1-128-528-11 1-128-528-11 1-126-967-11 CERAMIC CHIP CERAMIC CHIP ELECT ELECT ELECT 0.1uF 0.1uF 470uF 470uF 47uF 10% 10% 20% 20% 20% 16V 16V 25V 25V 50V C022 C023 C024 C033 C035 1-164-230-11 1-164-230-11 1-164-230-11 1-126-947-11 1-126-947-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT ELECT 220PF 220PF 220PF 47uF 47uF 5% 5% 5% 20% 20% 50V 50V 50V 35V 35V C036 C037 C040 C041 C042 1-100-388-21 1-100-388-21 1-107-826-11 1-107-826-11 1-107-826-11 ELECT CHIP ELECT CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 39uF 39uF 0.1uF 0.1uF 0.1uF 20% 20% 10% 10% 10% 16V 16V 16V 16V 16V C043 C045 C046 C047 C048 1-107-826-11 1-126-947-11 1-100-388-21 1-107-826-11 1-107-826-11 CERAMIC CHIP ELECT ELECT CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 47uF 39uF 0.1uF 0.1uF 10% 20% 20% 10% 10% 16V 35V 16V 16V 16V C049 C050 C051 C052 C053 1-107-826-11 1-107-826-11 1-107-826-11 1-107-826-11 1-107-826-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 10% 10% 10% 10% 10% 16V 16V 16V 16V 16V C054 C055 C056 1-107-826-11 CERAMIC CHIP 1-107-826-11 CERAMIC CHIP 1-126-964-11 ELECT 0.1uF 0.1uF 10uF 10% 10% 20% 16V 16V 50V 6-4 Part No. Les composants identifiés par une marque 0 sont critiquens pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. When indicating parts by reference number, please include the board. Description Remark C057 C058 1-107-826-11 CERAMIC CHIP 1-126-964-11 ELECT 0.1uF 10uF 10% 20% 16V 50V C060 C061 C062 C063 C064 1-107-826-11 1-126-964-11 1-165-884-91 1-165-884-91 1-165-884-91 CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 10uF 2.2uF 2.2uF 2.2uF 10% 20% 10% 10% 10% 16V 50V 6.3V 6.3V 6.3V C071 C072 C073 C074 C079 1-130-473-00 1-130-473-00 1-130-473-00 1-130-473-00 1-130-473-00 MYLAR MYLAR MYLAR MYLAR MYLAR 0.0015uF 0.0015uF 0.0015uF 0.0015uF 0.0015uF 5% 5% 5% 5% 5% 50V 50V 50V 50V 50V C080 C081 C082 C083 C084 1-130-473-00 1-130-467-00 1-130-467-00 1-130-467-00 1-130-467-00 MYLAR MYLAR MYLAR MYLAR MYLAR 0.0015uF 470PF 470PF 470PF 470PF 5% 5% 5% 5% 5% 50V 50V 50V 50V 50V C085 C086 C087 C088 C105 1-130-467-00 1-130-467-00 1-130-467-00 1-130-467-00 1-130-467-00 MYLAR MYLAR MYLAR MYLAR MYLAR 470PF 470PF 470PF 470PF 470PF 5% 5% 5% 5% 5% 50V 50V 50V 50V 50V C106 C107 C108 C109 C110 1-130-467-00 1-130-467-00 1-130-467-00 1-107-826-11 1-107-826-11 MYLAR MYLAR MYLAR CERAMIC CHIP CERAMIC CHIP 470PF 470PF 470PF 0.1uF 0.1uF 5% 5% 5% 10% 10% 50V 50V 50V 16V 16V C116 C117 C118 C119 C120 1-107-826-11 1-107-826-11 1-107-826-11 1-128-552-11 1-128-552-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT ELECT 0.1uF 0.1uF 0.1uF 47uF 47uF 10% 10% 10% 20% 20% 16V 16V 16V 63V 63V C121 C122 C123 C124 C125 1-128-552-11 1-128-552-11 1-107-826-11 1-136-165-00 1-136-165-00 ELECT ELECT CERAMIC CHIP FILM FILM 47uF 47uF 0.1uF 0.1uF 0.1uF 20% 20% 10% 5% 5% 63V 63V 16V 50V 50V C126 C127 C128 C129 C133 1-136-165-00 1-136-165-00 1-128-552-11 1-128-552-11 1-136-165-00 FILM FILM ELECT ELECT FILM 0.1uF 0.1uF 47uF 47uF 0.1uF 5% 5% 20% 20% 5% 50V 50V 63V 63V 50V AU-258 Ref. No. Part No. Description C134 C137 C138 C139 C140 1-136-165-00 1-162-927-11 1-162-927-11 1-162-927-11 1-162-927-11 FILM CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 100PF 100PF 100PF 100PF 5% 5% 5% 5% 5% 50V 50V 50V 50V 50V Remark C141 C142 C143 C144 C147 1-162-927-11 1-162-927-11 1-162-927-11 1-162-927-11 1-165-908-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 100PF 100PF 100PF 100PF 1uF 5% 5% 5% 5% 10% 50V 50V 50V 50V 10V C148 C149 1-165-908-11 CERAMIC CHIP 1-165-908-11 CERAMIC CHIP 1uF 1uF 10% 10% 10V 10V Ref. No. < DIODE > D001 D002 D003 8-719-914-43 DIODE DAN202K 8-719-988-61 DIODE 1SS355TE-17 8-719-988-61 DIODE 1SS355TE-17 < IC > IC001 IC002 IC003 IC004 IC006 6-702-296-01 6-700-792-01 8-759-052-52 8-759-679-55 6-707-237-01 IC IC IC IC IC NJM79M09DL1A-TE1 NJM78M09DL1A (TE1) L78M05T-FA SN74LVC08APWR PCM1791ADBR IC007 IC008 IC009 IC010 IC011 6-707-237-01 6-707-237-01 8-759-656-83 8-759-656-83 8-759-656-83 IC IC IC IC IC PCM1791ADBR PCM1791ADBR NJM4580MD-(TE2) NJM4580MD-(TE2) NJM4580MD-(TE2) < JACK > J001 J003 1-785-489-11 JACK, PIN 6P (5.1CH OUTPUT) 1-785-868-21 JACK, PIN 2P (AUDIO OUT L/R) < TRANSISTOR > Q001 Q002 Q003 Q004 Q005 8-729-421-19 8-729-921-80 8-729-421-19 8-729-045-17 8-729-010-29 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR UN2213 2SD1781K-T146-QR UN2213 2SB1561T100Q MSD601-RST1 Q006 Q007 Q008 Q009 Q011 8-729-027-53 8-729-027-53 8-729-010-05 8-729-010-05 8-729-027-53 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR DTC124TKA-T146 DTC124TKA-T146 MSB709-RT1 MSB709-RT1 DTC124TKA-T146 Q013 Q014 Q015 Q017 Q018 8-729-010-05 8-729-421-19 8-729-421-19 8-729-421-19 6-551-287-01 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR MSB709-RT1 UN2213 UN2213 UN2213 2SD2704K-T146 Q019 Q020 Q021 Q022 Q023 6-551-287-01 6-551-287-01 6-551-287-01 6-551-287-01 6-551-287-01 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR 2SD2704K-T146 2SD2704K-T146 2SD2704K-T146 2SD2704K-T146 2SD2704K-T146 < RESISTOR > R002 R004 R007 R009 1-216-809-11 1-216-801-11 1-216-801-11 1-216-801-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100 22 22 22 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 6-5 Part No. Description Remark R011 1-216-833-11 METAL CHIP 10K 5% 1/10W R012 R017 R018 R019 R020 1-216-833-11 1-216-833-11 1-216-801-11 1-216-833-11 1-216-833-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 10K 10K 22 10K 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R021 R022 R023 R024 R028 1-216-841-11 1-216-864-11 1-216-845-11 1-216-849-11 1-216-833-11 METAL CHIP SHORT CHIP METAL CHIP METAL CHIP METAL CHIP 47K 0 100K 220K 10K 5% 1/10W 5% 5% 5% 1/10W 1/10W 1/10W R029 R031 R032 R034 R035 1-216-841-11 1-216-833-11 1-216-833-11 1-216-833-11 1-216-833-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 47K 10K 10K 10K 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R036 R038 R077 R078 R080 1-216-833-11 1-216-833-11 1-216-809-11 1-216-809-11 1-216-809-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 10K 10K 100 100 100 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R081 R082 R083 R084 R085 1-216-657-11 1-216-657-11 1-216-657-11 1-216-657-11 1-216-657-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1.8K 1.8K 1.8K 1.8K 1.8K 0.5% 0.5% 0.5% 0.5% 0.5% 1/10W 1/10W 1/10W 1/10W 1/10W R086 R087 R088 R093 R094 1-216-657-11 1-216-657-11 1-216-657-11 1-216-657-11 1-216-657-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1.8K 1.8K 1.8K 1.8K 1.8K 0.5% 0.5% 0.5% 0.5% 0.5% 1/10W 1/10W 1/10W 1/10W 1/10W R095 R096 R103 R104 R105 1-216-657-11 1-216-657-11 1-216-663-11 1-216-647-11 1-216-647-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1.8K 1.8K 3.3K 680 680 0.5% 0.5% 0.5% 0.5% 0.5% 1/10W 1/10W 1/10W 1/10W 1/10W R106 R107 R108 R109 R110 1-216-663-11 1-216-663-11 1-216-647-11 1-216-647-11 1-216-663-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 3.3K 3.3K 680 680 3.3K 0.5% 0.5% 0.5% 0.5% 0.5% 1/10W 1/10W 1/10W 1/10W 1/10W R111 R112 R113 R114 R115 1-216-663-11 1-216-647-11 1-216-647-11 1-216-663-11 1-216-663-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 3.3K 680 680 3.3K 3.3K 0.5% 0.5% 0.5% 0.5% 0.5% 1/10W 1/10W 1/10W 1/10W 1/10W R116 R117 R118 R129 R130 1-216-647-11 1-216-647-11 1-216-663-11 1-216-663-11 1-216-647-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 680 680 3.3K 3.3K 680 0.5% 0.5% 0.5% 0.5% 0.5% 1/10W 1/10W 1/10W 1/10W 1/10W R131 R132 R133 R134 R135 1-216-647-11 1-216-663-11 1-216-663-11 1-216-647-11 1-216-647-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 680 3.3K 3.3K 680 680 0.5% 0.5% 0.5% 0.5% 0.5% 1/10W 1/10W 1/10W 1/10W 1/10W R136 R137 R138 R139 1-216-663-11 1-208-774-11 1-208-774-11 1-208-774-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP 3.3K 470 470 470 0.5% 0.5% 0.5% 0.5% 1/10W 1/10W 1/10W 1/10W AU-258 Ref. No. FL-176 Part No. Description Remark R140 1-208-774-11 METAL CHIP 470 0.5% 1/10W R141 R142 R143 R144 R145 1-208-774-11 1-208-774-11 1-208-822-11 1-208-822-11 1-208-822-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 470 470 47K 47K 47K 0.5% 0.5% 0.5% 0.5% 0.5% 1/10W 1/10W 1/10W 1/10W 1/10W R146 R149 R150 R153 R154 1-208-822-11 1-208-822-11 1-208-822-11 1-216-829-11 1-216-829-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 47K 47K 47K 4.7K 4.7K 0.5% 0.5% 0.5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R155 R156 R157 R158 R161 1-216-829-11 1-216-829-11 1-216-829-11 1-216-829-11 1-216-845-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 4.7K 4.7K 4.7K 4.7K 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R162 R163 R165 R166 R167 1-216-845-11 1-216-845-11 1-208-774-11 1-208-774-11 1-208-774-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100K 100K 470 470 470 5% 5% 0.5% 0.5% 0.5% 1/10W 1/10W 1/10W 1/10W 1/10W R168 R169 R170 R171 R173 1-208-774-11 1-208-774-11 1-208-774-11 1-208-774-11 1-208-774-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 470 470 470 470 470 0.5% 0.5% 0.5% 0.5% 0.5% 1/10W 1/10W 1/10W 1/10W 1/10W R175 R176 R177 R178 1-216-864-11 1-216-864-11 1-216-864-11 1-216-809-11 SHORT CHIP SHORT CHIP SHORT CHIP METAL CHIP 0 0 0 100 Ref. No. D105 Part No. Description Remark 8-719-036-94 DIODE RD5.6SB-T1 < FUSE > 0 F100 1-576-863-21 FUSE 0.5A 32V < FERRITE BEAD > FB001 FB002 FB003 FB004 1-414-226-21 1-414-226-21 1-414-226-21 1-414-226-21 INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD INDUCTOR, FERRITE BEAD < IC > IC100 8-759-643-83 IC uPD16315GB-3BS < COIL > L102 1-414-743-21 INDUCTOR 47uH < FLUORESCENT INDICATOR TUBE > ND100 1-519-958-11 INDICATOR TUBE, FLUORESCENT < TRANSISTOR > 5% Q100 Q101 Q102 Q103 Q104 8-729-027-46 8-729-901-00 8-729-901-00 6-551-382-01 8-729-901-88 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR Q105 8-729-901-88 TRANSISTOR DTC114YKA-T146 DTC124EK DTC124EK RSS040P03FD5TB 2SC2411K-CR 2SC2411K-CR < RESISTOR > 1/10W FL-176 BOARD, COMPLETE (Ref. No. 2000 Series) ********************** R100 R101 R102 R103 R104 1-216-864-11 1-216-833-11 1-216-864-11 1-216-837-11 1-216-837-11 SHORT CHIP METAL CHIP SHORT CHIP METAL CHIP METAL CHIP 0 10K 0 22K 22K R105 R106 R107 R108 R109 1-216-837-11 1-216-805-11 1-216-805-11 1-216-805-11 1-216-864-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP SHORT CHIP R110 R111 R112 R113 R117 1-216-824-11 1-216-845-11 1-216-838-11 1-216-833-11 1-216-833-11 R118 R119 R120 R121 R122 R123 R124 R125 R126 5% 1/10W 5% 5% 1/10W 1/10W 22K 47 47 47 0 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1.8K 100K 27K 10K 10K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W 1-216-832-11 1-216-834-11 1-216-833-11 1-216-824-11 1-216-825-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 8.2K 12K 10K 1.8K 2.2K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W 1-216-832-11 1-216-834-11 1-216-834-11 1-216-839-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP 8.2K 12K 12K 33K 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W < CAPACITOR > C101 C102 C105 C108 C113 1-125-972-91 1-107-826-11 1-164-227-11 1-125-972-91 1-163-021-91 ELECT CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP 100uF 0.1uF 0.022uF 100uF 0.01uF 20% 10% 10% 20% 10% 16V 16V 25V 16V 50V C115 C117 C118 C119 C120 1-107-826-11 1-107-715-11 1-115-339-11 1-115-339-11 1-115-339-11 CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 22uF 0.1uF 0.1uF 0.1uF 10% 20% 10% 10% 10% 16V 50V 50V 50V 50V C123 C124 1-107-726-91 CERAMIC CHIP 1-107-726-91 CERAMIC CHIP 0.01uF 0.01uF 10% 10% 16V 16V < CONNECTOR > CN100 CN101 1-770-658-11 CONNECTOR, FFC/FPC 30P 1-779-279-11 CONNECTOR, FFC (LIF (NON-ZIF)) 11P < DIODE > D100 D101 D102 D103 D104 8-719-941-86 8-719-988-61 8-719-988-61 8-719-988-61 8-719-988-61 DIODE DIODE DIODE DIODE DIODE DAN202U 1SS355TE-17 1SS355TE-17 1SS355TE-17 1SS355TE-17 The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. 6-6 Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. FL-176 Ref. No. Part No. Description Remark Ref. No. FR-271 Part No. MAIN POWER BLOCK Description Remark < SWITCH > S100 1-771-410-21 SWITCH, TACTILE (I/1) < TRANSFORMER > 0 T100 1-445-229-11 TRANSFORMER, DC-DC CONVERTER ************************************************************ ************************************************************ FR-271 BOARD, COMPLETE (Ref. No. 2000 Series) ********************** 0 1-474-057-41 POWER BLOCK (ZSSR641GA) (US, CND) 0 1-474-057-51 POWER BLOCK (ZSSR641IA) (AEP, UK, RUS, SP, TH, AUS) ************************ < CAPACITOR > C602 C605 1-107-826-11 CERAMIC CHIP 1-124-589-11 ELECT 0.1uF 47uF 10% 20% 16V 16V < CONNECTOR > * CN600 1-779-279-11 CONNECTOR, FFC (LIF (NON-ZIF)) 11P MISCELLANEOUS PARTS ******************** < DIODE > * D601 D603 D604 D605 6-501-546-11 6-501-437-01 6-501-437-01 6-501-437-01 DIODE DIODE DIODE DIODE NSPW-310BST-A0S SLI-343YC3F SLI-343YC3F SLI-343YC3F * 54 * 54 * 54 < IC > IC601 0 55 0 55 55 0 55 0 55 0 55 56 101 6-600-500-01 IC GP1UM28XK0SF < TRANSISTOR > Q600 Q602 Q603 Q604 8-729-421-22 8-729-421-22 8-729-421-22 8-729-421-22 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR UN2211 UN2211 UN2211 UN2211 ACCESSORIES & PACKING MATERIALS ******************************** < RESISTOR > R602 R604 R606 R607 R608 1-216-805-11 1-216-808-11 1-216-824-11 1-216-832-11 1-216-834-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 47 82 1.8K 8.2K 12K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R609 R610 R611 R612 R614 1-216-825-11 1-216-832-11 1-216-834-11 1-216-834-11 1-216-815-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 2.2K 8.2K 12K 12K 330 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R615 R616 1-216-815-11 METAL CHIP 1-216-815-11 METAL CHIP 330 330 5% 5% 1/10W 1/10W A001 A001 A001 0 0 0 0 < SWITCH > 0 S600 S601 S602 S603 S604 1-771-410-21 1-771-410-21 1-771-410-21 1-771-410-21 1-771-410-21 SWITCH, TACTILE (A) SWITCH, TACTILE (.) SWITCH, TACTILE (>) SWITCH, TACTILE (X) SWITCH, TACTILE (x) 1-479-848-31 REMOTE COMMANDER (RMT-B101A) (S300BJ/S300BJP/S300BM: US, CND/ S301BJ/S301BM) 1-479-848-41 REMOTE COMMANDER (RMT-B101A) (S300BM: E32) 1-480-207-21 REMOTE COMMANDER (RMT-B101P) (S300BM: AEP, UK, RUS, SP, TH, AUS) 1-555-074-52 CORD, POWER (S300BM: AUS) 1-569-008-22 ADAPTOR, CONVERSION 2P (S300BM: E32) 1-575-131-82 CORD, POWER (S300BM: AEP, RUS, E32, SP) 1-776-263-22 CORD, CONNECTION 1-823-701-11 CORD, POWER (S300BJ/S300BJP/S300BM: US, CND/ S301BJ/S301BM) 1-827-269-12 CORD, POWER (S300BM: UK) 1-834-169-11 CORD, CONNECTION (HDMI CABLE) (S301BJ/S301BM) The components identified by mark 9 contain confidential information. Strictly follow the instructions whenever the components are repaired and/or replaced. S605 1-771-410-21 SWITCH, TACTILE (H) ************************************************************ The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. 1-965-333-11 HARNESS (MBD-003) (S300BJ/S300BJP/S301BJ) 1-965-684-11 HARNESS (MBD-007) (S300BM: US, CND/S301BM) 1-965-688-11 HARNESS (MBD-008) (S300BM: AEP, UK, RUS, E32, SP, TH, AUS) A-1337-670-A DRIVE (P (SERVICE USE R1)) (US, CND) A-1337-673-A DRIVE (SKZ (SERVICE USE R1)) (US, CND) A-1337-677-A DRIVE (SOEM (SERVICE USE R2)) (AEP, UK) A-1337-678-A DRIVE (SOEM (SERVICE USE R4)) (AUS) A-1382-235-A DRIVE (SOEM (SERVICE USE R3)) (SP/TH) A-1382-236-A DRIVE (SOEM (SERVICE USE R5)) (RUS) 1-787-625-21 FAN, DC 1-834-107-11 CABLE, FLEXIBLE FLAT (FML-003) Les composants identifiés par la marque 9 contiennent des informations confidentielles. Suivre scrupuleusement les instructions chaque fois qu’un composant est remplacé et / ou réparé. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. 6-7 Ref. No. Part No. 0 1-834-539-11 CORD, POWER (S300BM: TH) 3-196-787-11 MANUAL, INSTRUCTION (ENGLISH) (S300BJ: CND/S300BJP/S301BJ) 3-196-787-21 MANUAL, INSTRUCTION (FRENCH) (S300BJ: CND) 3-212-651-11 MANUAL, INSTRUCTION (ENGLISH) (S300BJ: US) 3-214-290-11 MANUAL, INSTRUCTION (ENGLISH) (S300BM: US, CND/S301BM) Description Remark Ref. No. 3-214-290-21 MANUAL, INSTRUCTION (FRENCH) (S300BM/S301BM: CND) 3-214-800-11 MANUAL, INSTRUCTION (ENGLISH) (S300BM: UK) 3-214-800-21 MANUAL, INSTRUCTION (FRENCH) (S300BM: AEP) 3-214-800-31 MANUAL, INSTRUCTION (GERMAN) (S300BM: AEP) 3-214-800-41 MANUAL, INSTRUCTION (ITALIAN) (S300BM: AEP) 3-214-800-51 MANUAL, INSTRUCTION (SPANISH) (S300BM: AEP) 3-214-800-61 MANUAL, INSTRUCTION (DUTCH) (S300BM: AEP) 3-214-800-71 MANUAL, INSTRUCTION (SWEDISH) (S300BM: AEP) 3-214-800-81 MANUAL, INSTRUCTION (RUSSIAN) (S300BM: RUS) 3-214-801-11 MANUAL, INSTRUCTION (ENGLISH) (S300BM: SP, TH, AUS) 3-214-801-21 MANUAL, INSTRUCTION (SPANISH) (S300BM: E32) 6-8E Part No. Description Remark BDP-S300/S301 Sony Corporation 9-883-948-22 Home Electronics Network Company – 102 – 2007G0500-1 © 2007.7 Published by Quality Assurance Dept. BDP-S300/S301 REVISION HISTORY Ver. Date Description of Revision 1.0 2007.06 New 1.1 2007.07 Addition of AEP, UK, E, Russian, Australian, Singapore and Thai Models.