Download Craftsman 917.28001 Operator`s manual
Transcript
Operator's Manual III IIII RRFTSMRN°! IIII II I 30" RIDING MOWER SIDE DISCHARGE ELECTRIC START Model No. 917.28001 I This product has a low emission engine which operates differently from previously built engines. Before you start the engine, read and understand this Owner's Manual, IMPORTANT: Read and follow all Safety Rules and Instructions before operating this equipment, For answers to your questions about this product, Call: 1-800-659-5917 Sears Craftsman Help Line 5 am - 5 pm, Mon- Sat Gasoline containing up to 10% ethanol (El O)is acceptable for use In this machine. The use of any gasoline exceeding 10% ethanol (El0) will void the product warranty. Esta mdqulna puede utilizar gasolina con un contenido de hasta el 10% de etanol (E10). El uso de una gasolina que supere el 10% de etanol (EIO) anularzt la gamntia del producto. SEARS, ROEBUCK AND CO., HOFFMAN ESTATES, IL 60179 Visit our Craftsman website:www.sears.com!craftsman 439526 Rev. 2 U.S.A. Warranty ................................................. Safety Rules ........................................... Product Specifications ............................ AssemblyiPre-Qperation ........................ Operation .............................................. Maintenance Schedule ......................... 2 3 6 7 11 18 Maintenance ......................................... t8 Service and Adjustments ...................... 23 Storage ................................................. 27 Troubleshooting .................................... 28 Sears Service ........................ Back Cover Craftsman Riding Equipment Warranty CRAFTSMAN FULL WARRANTY FOR TWO YEARS from the date of purchase, all non-expendable parts of this riding equipment are warranted against any defects in material or workmanship. A defective non-expendable part will receive free in-home repair or replacement if repair is impossible. FOR FIVE YEARS from the date of purchase, the frame and front axle of this riding equipment are warranted against any defects in materiai or workmanship. A defective frame or front axle will receive free in-home repair or replacement if repair is impossible. FOR 90 DAYS from the date of purchase, the battery {an expendable part) of this riding equipment is warranted against any defects in material or workmanship (our testing proves that it will not hold a charge). A defective battery will receive free in-home replacement. ADDITIONAL LIFETIME LIMITED WARRANTY on CAST IRON FRONT AXLE (if equipped) FOR AS LONG AS IT IS USED by the original owner after the fifth year from the date of purchase, the cast iron front axle (if equipped) of this riding equipment is warranted against any defects in material or workmanship. With proof of purchase, a defective cast front axle will receive free in-home replacement WARRANTY SERVICE For warranty coverage details to obtain free repair or replacement, call 1-800-659-5917 or visit the web site: www.craftsman.com In all cases above, if part repair or replacement is impossible, the riding equipment will be replaced free of charge with the same or an equivalent model. All of the above warranty coverage is void if this riding equipment is ever used while providing commercial services or if rented to another person. This warranty covers ONLY defects in material and workmanship. Warranty coverage does NOT include: • Expendable parts (except battery) that can wear out from normal use within the warranty period, including but not limited to blades, spark plugs, air cleaners, belts, and oil filters. - Standard maintenance servicing, oil changes, or tune-ups. - Tire replacement or repair caused by punctures from outside objects, such as nails, thorns, stumps, or glass. • Tire or wheel replacement or repair resulting from normal wear, accident, or improper operation or maintenance. ; Repairs necessary because of operator abuse, including but not limited to damage caused by towing objects beyond the capability of the riding equipment, impacting objects that bend the frame, axle assembly or crankshaft, or over-speeding the engine. • Repairs necessary because of operator negligence, including but not limited to, electrical and mechanical damage caused by improper storage, failure to use the proper grade and amount of engine oil, failure to keep the deck clear of flammable debris, or failure to maintain the riding equipment according to the instructions contained in the operator's manual. • Engine (fuel system) cleaning or repairs caused by fuel determined to be contaminated or oxidized (stale). In genera], fuel should be used within 30 days of its purchase date. • Normal deterioration and wear of the exterior finishes, or product label replacement. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Sears Brands Management Corporation, Hoffman Estates, IL 60179 2 | | DANGER: This cutting machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury or death. • Never direct discharged material toward anyone. Avoid discharging material against awalf or obstruction. Material may ricochet back toward the operator. Stop the blade when crossing gravel surfaces. • Do not operate machinewithoutthe entire grass catcher, discharge chute, or other safety devices in place and working. * Slow down before turning. • Never leave a running machine unattended. Always turn off blade, set parking brake, stop engine, and remove keys before dismounting. , Disengage blade when not mowing. Shut off engine and wait for all parts to come to a complete stop before cleaning the machine, removing the grass catcher, or unclogging the discharge chute. ° Operate machine only in daylight or good artificial light. , Do not operate the machine while under the influence of alcohol or drugs. • Watch for traffic when operating near or crossing roadways. , Use extra care when loading or unloading the machine into a trailer or truck. - Always wear eye protection when operating machine. - Data indicates that operators, age 60 years and above, are involved in a large percentage of riding mower-related injuries. These operators should evaluate their ability to operate the riding mower safely enough to protect themselves and others from serious injury. - Keep machine free of grass, leaves or other debris build-up which can touch hot exhaust / engine parts and burn. Do not allow the mower deck to plow reaves or other debris which can cause build-up to occur. Clean any oil or fuel spillage before operating or storing the machine. Allow machine to cool before storage. _IbWARNING: In order to prevent accidental starting when setting up,transporting, adjusting or making repairs, always disconnect spark plug wire and place wire where it cannot contact spark plug. _IbWARNING: Do not coast down a hill in neutral, you may lose control of the riding mower. WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of Californiato cause cancer andbirth defects or other reproductive harm. _WARNING:This unit is not intended for the use of wheel weights. Only use attachments designed specifically for this riding mower. _WARNING: Battery posts, terminals and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling. I. GENERAL OPERATION - Read, understand, and follow all instructions on the machine and in the manual before starting. * Do not put hands or feet near rotating parts or under the machine. Keep clear of the discharge opening at all times. - Only allow responsible adults, who are familiar with the instructions, to operate the machine. , Clearthe area of objects such as rocks, toys, wire, etc., which could be picked up and thrown by the blade. • Be sure the area is clear of bystanders before operating. Stop machine if anyone enters the area. , Never carry passengers. , Do not mow in reverse unless absolutely necessary. Always look down and behind before and while backing. 3 Ii. SLOPE OPERATION Slopes are a major factor related to loss of control and tip-over accidents, which can result in severe injury or death. Operation on all slopes requires extra caution. If you cannot back up the slope or ifyoufeel uneasy on it, do not mow it. • Mow up and down slopes (15° Max), not across. • Watch for holes, ruts, bumps, rocks, or other hidden objects. Uneventerrain could overturn the machine. Tall grass can hide obstacles. • Choose a low ground speed so that you will not have to stop or shift while on the slope. ° Do not mow on wet grass. Tires may lose traction, ° Always keep the machine in gear when going down slopes. Do not shift to neutral and coast downhill. • If machine stops while going uphill, disengage blade, shift into reverse and back down slowly. • Avoid starting, stopping, or turning on a slope. Ifthetires]osetraction, disengage the blade and proceed s]owlystraight down the slope. • Keep all movementon the slopes slow and gradual. Do not make sudden changes in speed or direction, which could cause the machine to roll over. • Use extra care while operating machine with grass catchers or other attachments; they can affect the stability of the machine, • Do no use on steep slopes, - Do not try to stabilize the machine by putting your foot on the ground. • Do not mow near drop-offs, ditches, or embankments. The machine could suddenly roll over if a wheel is over the edge or if the edge caves in. III. CHILDREN Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the machine and the mowing activity. Never assume that children will remain where you last saw them. • Keep children outofthe mowing areaand in the watchful care of a responsible adult other than the operator. • Be alert and turn machine off if a child enters the area. • Before and while backing, look behind and down for small children. • Never carry children, even with the blade shutoff. They mayfall offand be seriously injured or interfere with safe machine operation. Children who have been given rides in the past may suddenly appear in the mowing area for another ride and be run over or backed over by the machine. • Never allow children to operate the machine. • Use extra care when approaching blind corners, shrubs, trees, or other objects that may block your view of a child. IV, SERVICE SAFE HANDLING OF GASOLINE To avoid personal injury or property damage, use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors are explosive. • Extinguish all cigarettes, cigars, pipes, and other sources of ignition. • Use only approved gasoline container. • Never remove gas cap or add fuel with the engine running. Allow engine to cool before refueling. • Never fuel the machine indoors. o Never storethe machine or fuel container where there is an open flame, spark, or piJot light such as on a water heater or other appliances. 4 • Never fill containers inside a vehicle or on a truck or trailer bed with plastic liner. Always place containers on the ground away from your vehicle when fitling. - Removegas-poweredequipmentfromthe truck or trailer and refuel it on the ground. If this is not possible, then refuel such equipment with a portable container, rather than from a gasoline dispenser nozzle. • Keep the nozzle in contact with the rim of the fuel tank or container opening at all times until fueling is complete. Do not use a nozzle lock-open device. • Iffuel is spitled on clothing, change clothing immediately. ° Never overfill fuel tank, Replace gas cap and tighten securely. GENERAL SERVICE - Never operate machine in a closed area. • Keep all nuts and bolts tight to be sure the equipment is in safe working condition. - Never tamper with safety devices, Check their proper operation regularly. • Keep machine free of grass, leaves, or other debris build-up. Clean oilorfuelspillage and remove any fuel-soaked debris. Allow machine to cool before storing. If you strike a foreign object, stop and inspectthe machine. Repair, if necessary, before restarting. • Never make any adjustments or repairs with the engine running. • Check grass catcher components and the discharge chute frequently and replace with manufacturer's recommended parts, when necessary. • Mower blade is sharp, Wrap the blade or wear gloves, and use extra caution when servicing them, • Check brake operation frequently. Adjust and service as required. • Maintain or replace safety and instruction labels, as necessary. , Be sure the area is clear of bystanders beforeoperating. Stop machine ifanyone enters the area. • Never carry passengers. • Do not mow in reverse unless absolutely necessary. Always look down and behind before and while backing. PRODUCT SPECIFICATIONS [GasolineCapacity 1.5 Gallons !andType: UnleadedRegular Oil Type (API SG-SL): Oil Capacity: SAE 30 (Above 32°F) SAE 5W30 (Below32°F) 48 Oz. Spark Plug: ChampionRC12YC (Gap: .030") GroundSpeed (Mph): Forward: Reverse: ChargingSystem: BladeBolt Torque: 3 Amps @ Battery 45-55 Ft. Lbs. 0- 4 0- 2 CONGRATULATIONS on your purchase of a new riding mower, It has been designed, engineered and manufactured to give you the best possible dependability and performance. Should you experience any problem you cannot easily remedy, please contact a Sears or other qualified service center. We have competent, well-trained representatives and the proper tools to service or repair this riding mower. Please read and retain this manual. The instructions will enable you to assemble and maintain your riding mower properly. Always observe the "SAFETY RULES". CUSTOMER RESPONSIBILITIES • Read and observe the safety ruies. • Follow a regular schedule in maintaining, caring for and using your riding mower. • Follewthe instructions under Maintenance and Storage sections of this manual. _,WARNING: This riding mower is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush-covered or grass-covered land unless the engine's exhaust system is equipped with a spark arrester meeting applicable local or state taws (ff any). If a spark arrester is used, it should be maintained in effective working order by the operator. lnthe state of Californiathe above is required by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federat lands. A spark arrester for the muffler is available through your nearest Sears service center (See REPAIR PARTS manual). REPAIR PROTECTIONAGREEMENTS Congratulations on making a smart purchase. Your new Craftsman® product is designed and manufactured for years of dependable operation. But like all products, it may require repair from timeto time. That's when having a Repair Protection Agreement can save you money and aggravation. Purchase a Repair Protection Agreement now and protect yourself from unexpected hassle and expense. Here's what's included in the Agreement: , Expert service by our 12,000 professional repair specialists. • Unlimitedserviceand nochargefor parts and labor on all covered repairs. • Product replacement if your covered product can't be fixed. • Discount of t0% from regular price of service and service-related parts not covered bythe agreement; also, 10% off regular price of preventive maintenance check. • Fast help by phone - phone support from a Sears representative on products requiring in-home repair,plus convenient repair scheduling. Onceyou purchasethe Agreement, asimple phone call is all that it takes for you to schedule service. Youcan call anytime dayor night, or schedute a service appointment online. Sears has over 12,000 professional repair specialists, who have access to over 4.5 million quality parts and accessories. That's the kind of professionalism you can count on to help prolong the life of your new purchase for years to come. Purchase your Repair Protection Agreement today[ Some limitations and exclusions apply. For prices and additional information call 1-800-827-6655. SEARS INSTALLATION SERVICE For Sears professional installation of home appliances, garage door openers, water heaters, and other major home items, inthe U.S.A. call 1-800-4-MY-HOME® = Steedng Wheel Insert Steedng (1) 5t16-18 Hex Bolt Shaft (1) Front Bumper x 4 Stee_ng Extension (t) Rear Bumper Wheel (1) Lockwasher j_ Steedng I Steering Boot @ Wheel Adapter Steedng (4)Screw Shaft Cover #10 x 0,200 (1) Large Flat (1) Shroud Washer (1) Cup Washer (2)Key Slope Sheet Seat (I) Knob Your new riding mower has been assembled at the factorywith the exception ofthose parts left unassembled for shipping purposes. To ensure safe and proper operation of your riding mower all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to ensure proper tightness. TOOLS REQUIRED FOR ASSEMBLY NOTE: Only cut carton with a short blade utility knife, a long blade or saw can puncture A socket wrench set will make assembly easier. Standard wrench sizes you need tires on unit. are listed below. HOW TO SET UP YOUR RIDING (1) 1/2" wrench (1) Tire pressure gauge MOWER (1) Utility knife CHECK BA'I-rERY Ensure battery is securelyfastened, andthat all wiresare securely connected, ° Battery is located under the seat, • Battery has been fully charged from the factory, before installation. When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel). TO REMOVE CARTON RIDING MOWER FROM UNPACK CARTON 1. Remove all accessible loose parts and parts boxes from carton. 2. Cut along dotted lines on all four panels of carton. Remove end panels and lay side panels flat. 3. Remove packing materials from riding mower. 4. Check for any additional loose parts or cartons and remove. Seat 7 artery TO INSTALL STEERING WHEEL 1. Slide extension shaft onto steering shaft. 2. Slide steering shaft protective foam cover over steering shaft. 3. Place steering boot over steering shaft and push down to secure. 4. Position fr0nt wheels ofthe riding mower so they are pointing straight forward. 5. Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft, 7. Press steering wheel into position on shaft, install large washer, lock washer, bolt and tighten securely. 8. Snap steering wheel insert into center of steering wheel securely. 7. Slide seat until a comfortable position is reached whichallows you to pressclutch/ brake pedal all the way down. 8. Get off seat without moving its adjusted position. 9. Raise seat and tighten adjustment knob securely. Seat Pan Pads Cup Washer Steering Boot_..... Adjustment _'_\ Extension Shaft _ FoamCover f g Shaft TO INSTALL SEAT Adjust seat before tightening adjustment knob. t. Remove adjustment knob and cup washer securing seat to cardboard packing and set aside. 2, Remove seat from the cardboard packing and set seat aside, Remove the cardboard packing and discard. 3. Place seat on seat pan so all three (3) bottom pads are positioned over large slotted holes in pan. 4. Push down on seat to engage pads in slots and pull seat towards rear of the riding mower, 5. Pivot seat andpanforward and assemble adjustment knob and cup washer loosely. Do not tighten. 6. Lower seat into operating position and sit in seat, NOTE: You may now rolt your riding mower off the skid. Follow the appropriate instruction below to remove the riding mower from the skid. WARNING: Before starting, read, understand and fo_low all instructionsin the Operation section of this manual. Be sure riding mower is in a well-ventilated area. Be sure the area in front of riding mower is clear of other people and objects. TO ROLL RIDING MOWER OFF SKID (See Operation section for location and function of controls) 1. Raise deck liftleverto itshighest position. 2. Release parking brake by depressing clutch/brake pedal. 3. Shift unit to neutral. 4. Roll riding mower forward off skid. • TO ATTACH REAR BUMPER NOTE: For ease of assembly,you may wisl to obtain the assistance of another person for mountingbumper to riding mower. 1. Remove (4) screws from rear chassisof riding mower, 2. Position bumper as shownandassemble to rear chassis with screws removed in step 1. 3, Tighten the four (4) screws securely, TO ATTACH FRONT BUMPER NOTE: For ease of assembly, you may wish to obtain the assistance of another person for mounting bumper to riding mower. 1. Remove (2) screws from front chassis of riding mower, 2. Tilt the front bumper so that the bumper tabs catch the slots on the front of the chassis and lower the bumper into place. 3, Attach the bumper to front of chassis with screws removed in step 1. 4. Tighten the two (2) screws securely. Rear Bumper CHECK TIRE PRESSURE The tires on your ridingmower were overinflated at the factory for shipping purposes. Correct tire pressure is important for best cuttingperformance. Screw 5, Position plastic shroud over bumper as shown and loosely assmeble to bumper with the four (4) supplied screws, 6, Tighten ati four (4) screws securely. CHECK DECK LEVELNESS For best cutting results, mower housing shouldbe properlyleveled, See "TO LEVEL MOWER HOUSING" in the Service and Adjustments section of this manual. Screws CHECK FOR PROPER POSITON OF MOWER DRWE BELT See the figure that is shownfor replacingthe mower drive belt in the service and adjustment section ofthis manual, Verify that the belt is routed correctly. CHECK BRAKE SYSTEM After you learn how to operate your riding mower, check to see that the brake is operating properly. Plasti_ Shroud 9 t_CHECKLIST Before you operate your new riding mower, we wish to assure that you receive the best performance and satisfaction from this Quaiit,/Product. Please review the following checklist: J All assembly instructions have been completed. ,/ No remaining loose parts in carton. ,/ Battery is properly connected. ,I Seat is adiusted comfortably and tightened securely. ,/ All tires are properly inflated, (For shipping purposes, the tires were overinflated at the factory.) ,/ Be sure mower deck is properly leveled side-to-side/front-to-rear far best cutting results. Fires must be properly inflated for leve_ing.) €" Check mower belt. Be sure it is routed properly around pulleys and inside all belt keepers, v" Check wiring. See that all connections are still secure and wires are properly clamped. While learning how to use your riding mower, pay extra attention to the following important iterr_s: 7" Engine oil is at proper level. J Fuel tank is filled with fresh, clean, regutar unleaded gasoline. J Become familiar with all controls, their location and function. Operate them before you start the engine. ,/ Be sure brake system is in safe operating condition. ,/ Be sure Operator Presence System and Reverse Operation System (ROS) are working properly (Seethe Operation and Maintenance sections in this manual,) 10 These symbols may appear on your riding mower or in literature supplied with the product. Learn and understand R their meaning. N REVERSE NEUTRAL H HIGH L LOW CHOKE FAST SLOW |GNITION ENGINEOFF REVERSE ENGINEON OPERATION SYSTEM(ROS) FUEL OIL PRESSURE ATTACHMENT CLUTCH ENGAGED BATTERY ATTACHMENT CLUTCH DISENGAGED ENGINESTART REVERSE PARKINGBRAKE FORWARD DANGER, KEEP HANDS AND FEET AWAY MOWER KEEP AREA SWITCH PARKING aRAKE PARKINGBRAKE LOCKED UNLOCKED HEIGHT CLEAR (SEE SAFETY MOWER SLOPE RULES LIFT HAZARDS SECTION) DANGER will result indicates In death aorhazard seriouswhich, injury.it not avoided, BRAKE/CLUTCH PEDAL WARNING hazard which, if not avoided, could resultindicates in deatha or serious injury. & Failure to follow instructions could result in serious injury or death. The safety alert symbol is used to identify safety information about hazards which can result in death, serious injury and/or property damage, CAUTION indicates a hazard which, if not avoided, might result in minor or moderate injury. CAUTION awhen usedthat without alertin symbol, indicates situation could the result damage to the tractor and/or engine. HOT SURFACES indicates a hazard which, if not avoided, could result in death, serious injury and/or property damage. FIRE indicates a hazard which, if not avoided, could result In death, serious Injury and/or property damage. 11 KNOW YOUR RIDING MOWER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR RIDING MOWER Compare the illustrations with your riding mower to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference. Brake Pedal Parking Lever Deck Clutch Lever IgniUon Switch Lift Lever Throttle/Choke Height Adjl Lever Motion Control Our riding mowers conform to the applicable safety standards of the American National Standards Institute. PARKING BRAKE LEVER - Locks parking brake into brake position. MOTION CONTROL LEVER - Selects the speed and direction of the riding mower. DECK CLUTCH LEVER - Used to engage the mower blade. BRAKE PEDAL- Used for braking the riding mower and starting the engine. HEIGHT ADJUSTMENT LEVER adjust mower cutting height. - Used to IGNITION SWITCH - Used for starting stopping the engine. ROS "ON" POSITION -Allows operation of mower deck or other powered attachment while in reverse. and LIFT LEVER PLUNGER - Used to release height adjustment lever when changing its position. THROTTLE/CHOKE CONTROL- Used for starting and controlling engine speed. 12 The operation of any riding mower can result in foreign objects thrown into the eyes, which can result in severe eye damage, Always wear safety glasses or eye shields while operating your riding mower or performing any adjustments or repairs. We recommend a wide vision safety mask over spectacles or standard safety glasses. GROUND DRIVE • Tostop ground drive, depress brake pedal all the way down. . Move motion control leverto neutralposition. ControlLever HOW TO USE YOUR RIDING MOWER TO SET PARKING BRAKE Your ridingmoweris equippedwithan operator presence sensing switch. When engine is running, any attempt by the operator to leave the seat withoutfirst setting the parking brake will shut off the engine. 1. Depress brake pedal all the way down and hold. 2. Pull parking brake lever up and hold, release pressure from brake pedal, then release parking brake lever, Pedal should remain in brake position. Ensure parking brake will hold mower secure. ENGINE o Move throttle control between haft and full speed (fast) position. NOTE: Failure to move throttle control between half and full speed (fast) position, before stopping, may cause engineto"backfire". STOPPING MOWER BLADE • To stop mower blade, move deck clutch lever to disengaged position. (_I_) "_ Deck Clutch Control "Engaged .... (!'_1))eck Clutch Control Disengaged" • Turn ignition key to "STOP" position and remove key. Always remove key when leaving riding mower to prevent unauthorized use. IMPORTANT: Leaving the ignitionswitch in any position other than "STOP" witl cause the battery to discharge and go dead. NOTE: Undercertain conditions when riding mower is standing idle with the engine running, hot engine exhaust gases may cause "browning" of grass. To eliminate this possibility, always stop engine when stopping riding mower on grass areas. CAUTION: Always stop riding mower completely, as described above, before leaving the operator's position. 13 TO USE THROTTLE CONTROL Always operate engine at full speed (fast). • Operating engine at less than full speed (fast)reduces engine's operating efficiency. - Full speed (fast) offers the best mower performance. Throttle \ TO MOVE FORWARD AND BACKWARD The direction and speed of movement controlled by the motion control lever. t. Ensure the parking 2, Start riding mower with motion lever in neutral (N) position. 3. Release 4, Slowly desired parking is brake is applied. control brake, move motion position, control Control lever • The average lawn should be cut to approximately 2-1/2" during the cool season and to over 3" during hot months. For healthier and better looking lawns, mow often and after moderate growth, • For best cutting performance, grass over 6" in heightshould be mowedtwice. Make the first cut relatively high; the second to desired height. TO OPERATE MOWER Your riding mower is equipped with an operator presence sensing switch, Any attempt by the operator to leave the seat with the engine running and the deck clutch engaged will shut off the engine, You must remain fully and centrally positioned in the seat to prevent the engine from hesitating or cutting off when operating your equipment on rough, rolling terrain or hills. 1. Select desired height of cut, 2, Start mower blade by engaging deck clutch lever. TO STOP MOWER BLADE Disengage deck clutch lever. DeckClutchLever MowerHeight "Disengaged"Position AdjustmentHigh Position to Lever \ \ \ \ Deck Clutch Lever "Engaged" Position TO ADJUST MOWER CUTTING HEIGHT The position of the mower height deck lift lever determines the cutting height, . Grasp lift lever, • Press lift lever plunger with thumb and move lever to desired position. The cutting height range is approximately 1-I/2to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed. Mower Height Adjustment Low Position _Jl, CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, mulch cover, or the deflector shield in place. Deflector Shield 14 Mulch Cover REVERSE OPERATION SYSTEM (ROS) Yourdding mowerisequippedwitha Reverse Operation System (ROS). Any attempt by the operator to travel in the reverse direction with the deck clutch engaged will shut off the engine unless ignition key is placed in the ROS "ON" position. _lkWARNING: Backing up with the deck clutch engaged while mowing is strong[y discouraged, Turning the ROS "ON", to allow reverse operation with the deck clutch engaged, should only be done when the operator decides it isnecessaryto reposition the machine with the attachment engaged. Do not mow in reverse unless absolutely necessary. USING THE REVERSE OPERATION SYSTEM Only use if you are certain no children or other bystanders will enter the mowing area, 1. Move motion control lever to neutral (N) position. 2. With engine running, turn ignition key counterclockwise to ROS "ON" position. 3. Look down and behind before and while backing. 4. Slowly move motion control lever to reverse (R) position to start movement. 5. When use of the ROS is no longer needed, turn the ignition key clockwise to engine "ON" position. ROS "ON" Position Hinge Bracket Shield 4. Rest the mulch cover on the deflector. 5. Attach the 1 bungee from the deflector to the deck. Deflector Shield TO OPERATE ON HILLS _WARNING: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope. Use the slope guide at the back of this manual. • Choosetheslowestspeed beforestarting up or down hills. • Avoid stopping or changing speed on hills, • If stopping is absolutely necessary, push clutch/brake pedal quickly to brake position and engage parking brake. • Move motion control lever to neutral (N) position. • To restart movement, slowly release parking brake and clutch/brake pedal. • Make all turns slowly. Engine "ON" Position (Normal Operating) TO ATTACH DEFLECTOR 1. Unhook the 2 bungees from deck to the mulch cover. TO TRANSPORT When pushing or towing yourridingmower, besure to disengagetransmission by placing shifter in neutral, o Raise mower height adjustment to its highest position with mower height adjustment lever. o To reengage transmission, press brake and shift out of neutral, Bungee Mulch Cover Cover Bungee 2, Liftthe mulch cover. 3. Attach the deflector to the hinge bracket. 15 BEFORE STARTING THE ENGINE CHECK ENGINE OIL LEVEL The engine in your riding mower has been shipped, from the factory, already filled with summer weight oil. 1. Check engine oil with riding mower on level ground. 2. Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw cap tight, wait for a few seconds, remove and read oil level. If necessary, add oil until "FULL' mark on dipstick is reached. Do not overfill. • For cold weather operation you should change oil for easier starting (See the oil viscosity chart inthe Maintenance section of this manual). • To change engine oil, see the Maintenance section in this manual, ADD GASOLINE • Fill fuel tank to bottom offiller neck. Do not overfill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life). Do not mix oil with gasoline. Purchase fuel inquantities that can be used within 30 days to assure fuel freshness. _, CAUTION: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame. CAUTION: Alcohol blendedfuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation ofacids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur. TO START ENGINE When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine. * Siton seatin operating position, depress clutch/brake pedal and set parking brake. - Place motion control lever in neutral position. • Move deck clutch lever to "DISENGAGED" position. Move throttle control to choke positionl NOTE: Before starting, read the warm and cold starting procedures below. ° Insert key intoignition andturn keyclockwise to "START" position and release key as soon as engine starts. Do not run starter continuously for more than fifteen seconds per minute. If the engine does not start after several attempts, move throttle control to fast position, wait a few minutes and try again. If engine still does not start, move the throttle control back to the choke position and retry. WARM WEATHER STARTING (50°F/10°C AND ABOVE) • When engine starts, move the throttle control to the fast position. , The ground drive can now be used. Ifthe engine does not accept the load, restart the engine and at]ow it to warm up for one minute usingthechoke as described above. COLD WEATHER STARTING (50°F/10°0 AND BELOW) • When engine starts, allow engine to run with the throttle control inthe choke position until the engine runs roughly, then move throttle control tofast position. This may require an engine warm-up period from several seconds to several minutes, depending on the temperature. Cap 16 MOWING TIPS - Mower should be properlyleveled for best mowing performance. See "TO LEVEL MOWER HOUSING" in the Service and Adjustments section of this manual. • The left hand side of mower should be used for trimming. • Drive so that clippings are discharged onto the area that has already been cut. Have the cut area to the right of the riding mower. This will result in a more even distribution of clippings and more uniform cutting. 1I ,1_,, • ° • • • When mowing large areas,startbyturning tothe right sothat clippings wil]discharge away from shrubs, fences, driveways, etc. After one ortwo rounds, mow in the opposite direction making [eft hand turns until finished. tf grass is extremely tall, it should be mowed twice to reduce load and possible fire hazard from dried clippings. Make first cut relatively high; the second to the desired height. Do not mow grass when it is wet. Wet grass will plug mower and leave undesirable clumps. Allow grass to dry before mowing. Regulate ground speed byselecting alow enough gear to give the mower cutting performance as well as the quality of cut desired. When operating attachments, select a ground speed that will suit the terrain and give best performance of the attachment being used. I7 MAINTENANCE R D I Check Operator, Presence & ROe Systems G (_ for Loose Check/Replace Clean BaKery Lubricate Friction Surfaces Check Mower L_velnes5 R; Check V-Beff SEASON STORAGE t/ ........... i/ v" v' v'0 i/ ,i,illllll iii =/ Check En,gine Oil Level Engine ....Ev_.Y F-E_o.E iv" V_3 and Spindles Axles EVERY 100 HOURS I v" Mower B|ad,e and Terminal5 Clean Change i/ EVERY 51) HOURS .IIHI Illl Fast,net5 E E e HOURS v" v" Check BrakePressure Qperatian Check Tire Check EVERY 25 HOURe F.VERY EACH USE SCHEDULE If , tf Oil .... N cIeanA_r Filter G Clean Inspe'ct Air v'2 Screen Muff|edSpark i/ Arc'ester ,= Clean Engine Cooling Replace Spark Replace Afr Filter GENERAL Fins v' ................... v" Plug =/, Paper Cartridge RECOMMENDATIONS BEFORE EACH USE 1. Check engine oil level. 2. Check brake operation. 3. Check tire pressure. 4. Check operator presence and ROS systems for proper operation. 5. Check for loose fasteners. The warranty on this riding mower does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator must maintain riding mower as instructed in this manual. Some adjustments will need to be made periodically to properly maintain your riding mower, IMPORTANT: Do not oil or grease the pivot points which have special nylon bearings. Viscous lubricants will attract dust and dirt that willshorten the life of the self-lubricating bearings, lfyou feel they must be lubricated, use only a dry, powdered graphite type lubricant sparingly. At least once a season, check to see if you should make any of the adjustments described in the Service and Adjustments section of this manual. - At least once a year you should replace the spark plug, clean or replace air filter, and check blade and belt for wear. A new spark plug and clean airfilter assure proper air-fuel mixture and help your engine run better and last longer. 18 RIDING MOWER Always observe safetyruleswhen performing any maintenance. BRAKE OPERATION If riding mower requires more than four (4) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced at your nearest authorized service center. TIRES - Maintain tire pressure at 12 PSI. o Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber. • Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage. NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion. AXLE AND SPINDLES • Front wheelaxles and front spindles should be properly lubricated. • Wheel axles and spindles should be lubricated with grease. CHECK REVERSE OPERATION (ROS) SYSTEM - Whenthe engine isrunning with the ignition switch inthe engine "ON" positionand the deck clutch lever engaged, any attempt by the operator to shift into reverse should shut off the engine. • When theengine is running withthe ignition switch in the ROS "ON" position and the deck clutch lever engaged, anyattempt by the operator to shift into reverse should NOT shut off the engine. ROS "ON" Position BLADE CARE For best results mower blades must be sharp, Replace worn, bent or damaged blades. -&CAUTION: Use only a replacement blade approved by the manufacturer of your riding mower. Using a blade not approved by the manufacturer of your riding mower is hazardous, could damage your riding mower and void your warranty. BLADE REMOVAL !. Raise mower to highest position to allow access to blade, NOTE: Protect your hands with gloves and/ or wrap blade with heavy cloth, 2. Remove blade bolt by turning counterclockwise. 3. Install new blade with stamped "THIS SIDE UP" facing deck and mandrel assembly. Whe Sel pinAxlde_. OPERATOR PRESENCE SYSTEM AND REVERSE OPERATION SYSTEM (ROS) Be sure operator presence and reverse operation systems are working properly. If your riding mower does not function as described, repair the problem immediately. - The engine should not start unless the brake pedalisfully depressed, andthe deck clutch lever is in the disengaged position. CHECK OPERATOR PRESENCE SYSTEM - When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine. • When the engine is running and the deck clutch Feveris engaged, any attempt by the operator to leave the seat should shut off the engine. • Never operatethe deck clutch lever unless you are seated in the seat. Engine "ON" Position (Normal Operating) Mandrel Assembly (Special .Star Center Hole IMPORTANT: To ensure proper assembly, center hole in blade must align with star on mandrel assembly. 4. Install and tighten blade bolt securely (45-55 Ft. Lbs.). IMPORTANT: Special blade bolt is heat treated. 19 BATTERY Your riding mower has a battery charging system which is sufficient for normal use. - Keep battery and connectors clean. * Only recharge battery with charger approved for a 12V 6 amp. hour battery. • Charging with any other charger or an automotive style charger can cause permanent damage to the battery. * Charge battery for 24 hours for a full charge. NOTE: The original equipment battery on your riding mower is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary, _WARNING: Do not jump start battery. Permanent damage to the battery or personal injury may occur. TRANSAXLE COOLING Keep transaxle free from build-up of dirt and chaff which can restrict cooling. V-BELT Check V-belt for deterioration and wear after 100 hours of operation and replace if necessary. The belt is not adjustable. Replace belt ff it begins to slip from wear. ENGINE LUBRICATION Only use high quality detergent oil rated with API service classification SG-SL. Selectthe oil's SAE viscosity grade according to your expected operating temperature, SAE V_SCOSITY TO CHANGE ENGINE OIL Determine temperature range expected before oil change. All oil must meet API service classification SG-SL. • Be sure riding mower is on level surface. • Oil will drain more freely when warm. • Catch oil in a suitable container. _IL CAUTION: If engine has been operated for an extended period of time immediately prior to draining oit, oil will be hot. 1. Lift engine cover. 2. Remove oi! fill cap/dipstick. Be careful not to allow dirt to enter the engine when changing oil. 3. Position a container to catch oil. 4. Remove drain plug and drain oil into container. 5. Afteroil has drained completely, replace oil drain plug and tighten securely. 6. Refill engine with oil through oil fill dipstick tube. Pour slowly. Do not overfill. For approximate capacity see "PRODUCT SPECIFICATIONS" section of this manual. 7. Use gauge on oil fill cap/dipstick for checking level. For accurate reading, tighten dipstick cap securely onto the tube before removing dipstick. Keep oil at "FULL' line on dipstick. Tighten cap onto the tube securely when finished. 8. Lower engine cover. Engine Cover GRADES Oil Fill Cap/Dipstick Drain Plug NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, the oils will result in increased oil consumption when used above 32°E Check your engine oiI level more frequently to avoid possible engine damage from running low on oil. Change the oil after every 25 hours of operation or at least once a year if the riding mower is not used for 25 hours in one year. Check the crankcase oil level before starting the engine and after each eight (8) hours of operation. Tighten oil fill cap/dipstick securely each time you check the oil level. 20 \\ \ _/ // DECK WASHOUT PORT Your riding mower's deck is equipped with a washout port on its surface as part of its deck wash system. It should be utilized after each use. 1. Drive the riding mower to a level, clear spot on your lawn, near enough to a water spigot for your garden hose to reach. IMPORTANT: Make certain the riding mower's discharge chuteis directed AWAY from your house, garage, parked cars, etc. Remove bagger chute or mulch cover ff attached. 2. Make sure the attachment clutch control is in the "DISENGAGED" position, set the parking brake, and stop the engine, 3. Thread the nozzle adapter (packaged with your riding mower's Operator's Manual) onto the end of your garden hose. 4. Pull back the lock collar of the nozzle adapter and push the adapter onto the deck washout port at the left end of the mower deck, Release the lock collar to lock the adapter on the nozzle. Nozzle _/Hose Adapter_.._ Washout 8, Move the riding mower's attachment clutch control to the "DISENGAGED" position. Turn the ignition key to the STOP position to turn the tractor's engine off. Turn the water off. 9. Pull back the lock collar of the nozzle adapter to disconnect the adapter from the nozzle washout port. 10. Move the riding mower to a dry area, preferably a concrete or paved area. Place the attachment clutch control in the "ENGAGED" position to remove excess water and to help dry before putting the riding mower away. _LWARNING: A broken or missing washout fitting could expose you or others to thrown objects from contact with the blade. • Replace broken or missing washoutfitting immediately, prior to using mower again. • Plug any holes and Iocknuts. in mower with bolts AIR FILTER Your engine will not run properly using a dirty air filter. Service air cleaner more often under dusty conditions. See engine manual, CLEAN AIR SCREEN Air screen must be kept free ofdirt and chaff to preventenginedamagefrom overheating. Clean witha wire brushorcompressed airt0 remove dirt and stubborn dried gum fibers. IMPORTANT: Tug hose ensuring connection is secure. 5. Turn the water on. 6. While sitting in the operator's position on the riding mower, re-start the engine and place the throttle lever in the Fast "4_" position. IMPORTANT: Recheck the area making certain the area is clear. 7. Move the riding mower's attachment clutch control to the "ENGAGED" position. Remain in the operator's position withthe cuttingdeckengaged until the deck is cleaned. 21 CLEAN AIR INTAKE/COOLING AREAS To ensure proper cooling, make sure the grass screen, coolingfins, and other external surfaces of the engine are kept clean at all times. Every 100 hours of operation (more often under extremely dusty, dirty conditions), remove the blower housing and other cooling shrouds. Cieanthe cooling fins and external surfaces as necessary. Ensure the cooling shrouds are reinstalled. NOTE: Operating the engine with ablocked grass screen, dirty or plugged cooling fins, and/or cooling shrouds removed will cause engine damage due to overheating, CLEANING FRICTION SURFACES To ensure proper drive performance keep the friction surfaces free from dirt, chaff and excess rubber at all times. Every 25 hours of operation, the friction surfaces need to be rubbed clean with isopropyl alcohol or other non-filming cleaner. Engine Plate Friction Disc MUFFLER inspect and replace corroded muffler and spark arrester (if equipped) as it could create a fire hazard and/or damage. SPARK PLUG(S) Replace spark plug(s) at the beginning of each mowing season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in "PRODUCT SPECIFICATIONS" section of this manual. CLEANING • Clean engine, battery, seat, finish, etc. of all foreign matter, • Keep finished surfaces and wheels free of all gasoline, oil, etc. • Protect painted surfaces with automotive type wax. We do not recommend using a garden hose or pressure washer to clean your riding mower unless the engine and transmission are covered to keep water out. Water in engine or transmission wiil shorten the useful life of your riding mower, Use compressed air or a leaf blower to remove grass, leaves and trash from riding mower and mower. 22 SERVICE ORTO WARNING: ADJUSTMENTS: AVOID SERIOUS INJURY, BEFORE PERFORMING ANY 1. Depress clutch/brake pedal fully and set parking brake. 2. Place motion control lever in neutral (N) position. 3. Place deck clutch in "DISENGAGED" position. 4. Turn ignition key to "STOP" and remove key, 5, Ensure the blade and all moving parts have completely stopped. 6. Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug, RIDING MOWER TO REMOVE MOWER 1. Place deck clutch in "DISENGAGED" position. 2. Move mower height adjustment lift lever forward to lower mower to its lowest position. 3, Remove mandrei cover. 4. Remove pins holding left and right front mower suspension arms in place. 5. Remove bolt holding deck front to rear leveling rod in place. 6. Remove pin holding deck lift link arm in place. 7. Remove bolt holding deck side to side leveling rod in place, 8, Remove belt from around pulleys. 9. Slide deckout from under side of mower. TO INSTALL MOWER Installin reverseorderfollowinginstructions in "TO REMOVE MOWER" section. Deck Leveling Side to Side Rod Bolt Mandrel Cover Front Leveling Lift Link Pin Mower Suspension Arm Pin 23 TO LEVEL MOWER HOUSING Adjust the mower while riding mower is parked on level ground or driveway. Ensure tires are properly inflated. If tires are over or underinflated, you will not properly adjust your mower. SI DE-TO-SIDE ADJUSTMENT • Raise mower to its highest position. • Measure distance "A" from bottom edge of mower to ground level at front corners of mower, Bottom Edgeof Mower to Ground BottomEdgeof Mowerto Ground t!! il ....... tl !tJ x' • To raise the right side ofthe mower, tighten lift link adjustment nut. • To lower the rightsideofthe mower, loosen lift link adjustment nut. NOTE: Each full turn of adjustment nut will change mower height about 3/16". • Recheck measurements after adjusting. Adjustment FRONT-TO-BACK ADJUSTMENT IMPORTANT: Deck must be level side-to side. Toobtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its highest position. Check adjustment on right side of riding mower. Measure distance"F" directly infront and behind the mandrel at bottom edge of mower housing as shown. • To lower front of mower housing turn nuts "G" and "H" clockwise. • When distance "F" is 1/8" to 1/2" lower at front than rear, tighten nut "H" against trunnion on front link. • To raise front of mower housing turn nuts "G" and "H" counter clockwise. • When distance "F" is 1/8" to 1/2" lower at front than rear, tighten nut "H" against trunnion on front link. NOTE: Each full turn of "G" will change "F" by approximately about 3/8". Nut • Recheck Turn nut left "\'\_'_/_. _-_" side-to-side Turnnut right Nut to raise mower . \-_\i__ _o iower mower Trunnion i 24 adjustment. TO REPLACE MOWER BLADE DRIVE BELT TO ADJUST STEERING WHEEL ALIGNMENT Ifsteeringwheeicrossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steering wheel and reassemble per instructions in the "INSTALL STEERING COLUMN" section of this manual. MOWER DRIVE BELT REMOVAL I. Park riding mower on a level surface. 2. Set parking brake. 3, Lower mower to its lowest position, 4. Remove mandrelcoverfrem mowerdeck. 5. Remove rear engine plate from unit. 6. Remove rear belt keeper from unit. 7, Carefully roll belt over the top of the mower blade mandrel, TO REMOVE WHEEL FOR REPAIRS FRONT WHEEL 1. Block up front axle securely. 2. Remove dust cover, retaining ring, and washer to allow wheel removal. 3. Repair tire and reassemble. 4. Replace washer and retaining ring securely in axle groove. REAR WHEEL 1. Block up Rear axle securely. 2. Remove dustcover,retainingring,washer, and square key while pulling tire off. 3. Repair tire and reassemble. 4, Replacesquare keywhile putting tire back on, then replace washer and retaining ring securely in axle groove. Ma _drel 8, Remove belt from idler pulleys, 9. Check idler pulleys to seethatthey rotate freely, 10, Remove belt from rear drive pulley. MOWER DRIVE BELT INSTALLATION Install in reverse order following instructions in "MOWER DRIVE BELT REMOVAL" section. TO CHECK BRAKE If riding mower requires more than four (4) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced. You may also check brake by: 1. Park riding mower on a level, dry concrete or paved surface, depress clutch/ brake pedal all theway down and engage parking brake. 2. Place motion control lever in neutral position. The rear wheels must lock and skid when you try to manually push the riding mower forward. If the rear wheels rotate, then the brake needs to be serviced. Contact a Sears or other qualified service center, Washer Retaining [ Ring Dust Cover / SquareKey (rear wheel only) NOTE: To seal tire punctures and prevent flat tires due to slow leaks, purchase and use tire sealantfrom Sears. Tire sealant also prevents tire dry rot and corrosion. TO START ENGINE WITH A WEAK BATTERY _I_CAUTION: Lead-acid batteries generate explosive gases. Keep sparks, flame and smokingmaterials away from batteries. Always wear eye protection when around batteries. If your battery is too weak to startthe engine, _tshould be recharged. (See "BATTERY" in the Maintenance section of this manual). 25 REPLACING BATTERY _t, WARNING: Do not short battery terminals by allowing awrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc. Positive terminal must be connected first to prevent sparking from accidental grounding. t. Lift seat pan to raised position. 2. Remove terminal cover. 3. Disconnect BLACK battery cable then RED battery cabie, battery strap and carefully remove battery from riding mower. 4. Install new battery with terminals insame position as old battery, 5. Reinstall terminal cover. 6. First connect RED battery cable to positive (+) battery terminal with bolt and nut as shown. Tighten securely, 7, Connect BLACK grounding cable to negative (_) battery terminal with remaining bolt and nut, Tighten securely 8. Lower seat 3an. Nut. Cable [_-_'. _t _ Nut uaoie INTERLOCKS AND RELAYS Loose or damaged wiring may cause your riding mower to run poorly, stop running, or prevent it from starting. • Check wiring. Ensure all wiring and connectors are secure, ENGINE Your carburetor is net adjustable. If your engine does not operate properly due to suspected carburetor problems, take your riding mower to a qualified service center for repair and/or adjustment. 26 Immediately prepare yourriding mower for • Empty the fuel tank by starting the engine storage attheendoftheseason Orifthe and letting it run until the fuel lines and ridingmower wiltnotbeusedfor30days carburetor are empty. or more. • Never use engine or carburetor cleaner _kWARNING: Neverstorethe riding mower products in the fuel tank or permanent withgasoline inthetankinside a building damage may occur, where fumesmayreach anopenflame or • Use fresh fuet next season. spark. Allowtheengine tocootbefore stor- NOTE: Fuel stabilizer is an acceptable alingin any enclosure. ternative in minimizing the formation of fuel MOWER Remove deckfrom mower for winter storage. When mower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in aclean, dryarea. I. Clean entire riding mower (See"CLEANING" in the Maintenance section of this manual). 2. Inspect and replace belt, if necessary (See belt replacement instructionsinthe Service and Adjustments section of this manual), 3. Lubricate as shown in the Maintenance section of this manual, 4. Be sure that all nuts, bolts and screws are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary. 5, Touch up all rusted or chipped paint surfaces; sand lightly before painting. BATTERY •FuIly charge • If battery is for storage, on concrete gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not empty the gas tank and carburetor if using fuel stabilizer, ENGINE OIL Drain oil (with engine warm) and replace with clean engine oil. (See "ENGINE" in the Maintenance section of this manual). CYLINDER(S) 1. Remove spark plug(s). 2. Pourone ounce of oil through spark plug hole(s) into cylinder(s). 3. Turn ignition key to "START" position for a few seconds to distribute oil. 4. Replace with new spark plug(s). OTHER • Do not store gasoline from one season to another. the battery for storage. removed from riding mower do not store battery directly or damp surfaces. ENGINE FUEL SYSTEM IMPORTANT: It is important to prevent gum deposits from forming in essential fuel system parts such as carburetor, fuel hose, ortankduring storage. Also, alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. • Replaceyourgasolinecan ifyourcan starts to rust. Rust and/or dirt in your gasoline will cause problems. • if possible, storeyour riding mower indoors and cover it to give protection from dust and dirt. • Cover your riding mower with a suitable protectivecoverthat does not retain moisture. Do not use plastic. Plastic cannot breathe which allows condensation to form and wilt cause your riding mower to rust. IMPORTANT: Never cover riding mower while engine and exhaust areas are still warm, 27 TROUBLESHOOTING CHART: See appropriate section in manual PROBLEM CAUSE Will not start Hard to start unless directed to Sears service center. 1 2 3 4 Out of fuel. 1 Fill fuel tank. Bad spark plug. Dirty air filter. Water in fuel, 2 3 4 5 6 Loose or damaged wiring, Engine valves out of adjustment. Replace spark plug. Glean/replace air filter, Empty fuel tank and carburetor, refill tank with fresh gasoline and replace fuel filter, Check all wiring. Contact a Sears or other qualified service center. 1 Didy air filter. 2 _Bad spark plug, 2, Weak or dead battery. 4 Stale or didy fuel. !5 6 Loose or damaged wiring, Engine valves out of adjustment. 5 16 1 Clean/replace air filter, 2 Replace spark plug. 3 Recharge or replace battery. 4 I Empty fuel tank and refill tank with i fresh, clean gasoline, 5 Check all wiring, 6 Contact a Sears or other qualified service center, Engine will not turn over 1 2 3 4 5 6 7 8 9 Clutchs/brake pedal not depressed. Deck clutch is engaged. Weak or dead battery. Blown fuse. Corroded battery terminals, Loose or damaged wiring. Faulty ignitionswitch. Faulty solenoid or starter, Faulty operator presence switch(es), I 2 3 4 5 6 7 8 9 Depress clutch/brake pedal. Disengage deck clutch. Recharge or replace battery. Replace fuse, Clean batten./terminals. Check all wiring, Check/replace ignition switch. Check/replase solenoid or starter, Contact a Sears or other qualified servme center, Engine clicks but will not start 1 2 3 4 Weak or dead battery. Corroded battery terminals, Loose or damaged wiring. Faulty solenoid or starter. 1 2 3 4 Recharge or replace battery. Clean battery terminals, Check all wiring. Check/replace solenoid or starter. Loss of power t 2 1 2 Raise cutting height/reduce speed Clean underside of mower housing. 3 4 5 6 Cutting too much grass!toe fast. Build-up of grass, leaves and trash under mower. Dirty air filter. Low oil level/dirty ei[ Faulty spark plug. Stale or dirty fuel. 3 4 5 6 7 Water in fuel. 7 Clean/replace air filter, Check oil leve!/change oil. Ctean& regap or change spark plug Empty fuel tank and refill tank with fresh, clean gasoline, Empty fuel tank and carburetor,refill tank with fresh gasoline. 8 Spark plug wire loose. 8 Connect & tighten spark plug wire, 9 Dirtyengine air screen/fins. 9 Clean engine air scrae_fins. I0 Clean/replace muffler, ...... ,,,,,,,,,,,,,, 10 Excessive vibration muffler. wiring, !11 Check all wiring. out of adjustment, t2 Contact a Sears or other qualified service center. 11 Loose or damaged 12 Engine 1 i2 Engine continues to run when operator leaves seat with attachment clutch engaged =Dirty/clogged Worn. valves bent or loose Bent blade blade. mandrel. 3 Loose/damaged 1 Faulty operator-safety control system. 1 Replace blade. Tighten blade bolt. , Contact a Sears or other qualified service center, 3 Tighten loose part(s), Replace damaged parts. 2 part(s), presence 28 1 Check wiring, switches and connections, If not corrected, Contact a Sears or other qualified sewice center. TROUBLESHOOTING CHART: See appropriate section PROBLEM in manual unless directed Sears service center. tl CAUSE' CORRECTION .... ,,,,, , ,,,,,,,,,,, ,,,,, ,,, Poor cut - uneven cutting t 2 3 14 Worn, bent or loose blade. Mower deck not level. 1Buildup of grass, leaves, and trash under mower, Bent blade mandrel. 1 2 Replace blade. Tighten blade bolt. Level mower deck, 3 Clean underside of mower housing. 4 C]ogged mower deck vent from build.up of grass, leaves, and trash around mandrel. 5 Contact a Sears or other qualified service center. Clean around mandrels to open vent holes, 1 2 3 4 Mower blade will not rotate 1 2 3 4 Obstruction in clutch mechanism. Worn]damaged mower ddve belt. Frozen idler pulley. Frozen blade mandrel Poor grass discharge 1 2 3 4 5 Travel speed too fast. Wet grass. Mower deck not level. Low/uneven tire air pressure. Worn. bent or loose blade. 1 2 3 Shift to slower speed. Allowgrass to dr,/before mowing. Level mower deck, 4 5 Buildup of grass, leaves and trash under mower. Mower drive belt worn. Blade improperly installed. Improper blade used. 6 7 8 9 Clogged mower deck vent holes from buildup of grass, leaves, and trash around mandrels. _o Check tires for proper PSI, Replace/sharpen blade. Tighten blade bolt. Clean underside of mower housing. Replace mower drive belt. Reinstall blade sharp edge down. Replace w_thblade listed in parts manual, i Clean around mandrels to open vent holes. Remove obstruction. Replace mowerdrive belt. Replace idler pultey. Contact a Bears or other qual_ed service center. ,,, ,,,, 10 7 8 9 ,,,,, 1 2 3 Battery will not charge ,,.,,,_,, Bad battery cell(s). Poor cable connections. Fault,,/alternator. 1 2 3 Replace battery, Check/clean al[ connections, Replace aRemator, 1 tnstali axle key at rear wheel. See 'q'O REMOVE WHEEL" in the Service and Adjustments section. 1 Turn ignition key to ROB "ON '_ 2 position. Bee Operation section, Allow engine warm-up by running for I several seconds to several minutes. I ,,,,,,,,, ,,, Axle key missing. Loss of drive ,,,,,,,,, , i Engine dies when riding mower is shifted into reverse i2 NEED MORE ........... Reverse operation system (ROB) is not "ON" while mower or other ;attachment is engaged. Engine is cold, HELP? You'll find the answer and more on managemyhome.com • Find this and atl your other product manuals online. • Get answers from our team of home experts. • Get a personalized • Find information manage maintenance and tools p[an for your to help with home. home projects. home brought to yeu by Sez=_rs 29 - for free! SUGGESTED GUIDE FOR SIGHTING SLOPES ONLY RIDE UP AND NOT ACROSS HILL 15 DEGREES DOWN FOR SAFE OPERATION HILL, MAX. down the face of slopes, never across the face. Do not mow WARNING: To avoid serious injury, operate your tractor up and slopes greater than 15 degrees. Make turns gradually to prevent tipping or loss of control. Exercise extreme caution when changing direction on stopes. 1. Fold this page along dotted line indicated above. 2. Hold page before you so that its left edge is vertically parafle! to a tree trunk or other upright structure. 3. Sight across the fold in the direction of hill slope you want to measure, 4. Compare the angle of the-fold with the slope of the hill. Garantfa ............................................ ,.,, 31 Reglas de seguridad ............................. 32 Especificaciones del producto .............. 35 EnsambladoiPreoperaci6n ................... 36 Operaci6n ............................................. 40 Garantia para GARANTiA equipos COMPLETA tractores Programa de mantenimiento ................ Mantenimiento ...................................... Servicio y Ajustes ................................. Almacenamiento ................................... SotuciSn de problemas ......................... 47 47 52 56 57 Craftsman DE CRAFTSMAN PeR DOS At-JOS desde la fecha de compra, todas las pai'tes no sustituibles de eete eqUZpo tractor estdn garantizadas contra cualquier defecto de material o mane de obra. Una parle no sustituible defectuosa recibir& reparaciSn o reemptazo gratuito en casa si la reparaci6n es imposible. PeR CINCO ANOS desde la fecha de compra, e] bastidor y el eje delantero de este equips tractor est&n garantizados contra cualquier defecto de material o mane de obra. Un bastictor o eje delantero defectuoso recibir& reparaciSn o reemplazo gratuito en casa sila reparaciSn es imposible. DURANT_ 90 DiAS desde la fecha de compra, ta baterla (una parle sustituible) de este equipo tractor est& garantizada contra cua[quier defecto de material o mane de obra (nuestra prueba comprueba que no contendr& carga). Una bateda defectuosa recibir& un reemp|azo gratuito en casa. GARANTJA LIMITADA DE PeR VIDA ADICIONAL en el EJE DELANTERO DE HIERRO COLADO (sJ est_ prov[sto) DURANTE EL TIEMPO EN QUE SE USE per el propietario original despu_s del quinto a_o a partir de [a fecha de compra, el eje delantero de hierro colado (si est_ provisto) de este equipo tractos est_ garantizado contra cualquier defecIo de mateda[ o mane de obra. Con el comprobante de ¢ompra, un eje delantero de hierro colado recibir& un reemplazo gratuito en casa. SERVICIO DE GARANTIA Para conocer los detalIes de la cobertura de garantia para obtener una reparaci6n I[am_ aI 1-800-659-5917 6 visite el sitio web: www. craftsman.corn o reemplazo gratuito, En todos los cases anteriores, si el reemplazo es lmposible, el equipo tractor ser,'_sustituido sin cargo con el mismo modelo o uno equivatente. Toda [a coberlura de garantia anterior ser,_ nufa si este equipo tractor se utiliza alguna vez para brindar servicios comerciales osi se alquila a otra persona. Eeta garantiacubre _INICAMENTEdefectos de materialy mane deobra. La coberturade garantfa NO incluye: • Panes sustituibJes (excepto la bateria) que se puedan desgastar per el use normal dentro del periodo de garantia incluso, pete sin timitarse a, cuchillas, buj(as, fittros de aire, correas y fillies de aceite. • Servicios de mantenimiento est&ndar, ¢ambios de aceite o afinaciones. • Reemplazo o reparaciSn de neum_,ticos per pinchazos causados per objetos externos come clavos, espinas, 'tocones o vittles. • Reemp[azo o reparaci6n de neum_ticos o ruedas per desgaate normal, accidentes o per operaci6n o mantenimiento incorrectos. • Reparaciones necesar_as pot abuse del operador incluso, pete sin limitarse a, daSos causados per remolcar obietos que superen la capacidad del equipo tractor, chocar contra objetos que doblen el baetidor, el ensamble del eje o el cig0ef_al o sobrepasar la velocidad del motor. • Reparaciones necesarias per negligencia del opeTador, Incluso (pete sin timitarse a silo) dafios el_ctricos y mec&nicos causados porel almacenamiente incorrecto, per no usarel grade y la cantidad correctos de aceite de motor, per no mantener del muelle fibre de residues inflamables o per no mantener el equipo tractor de acuerdo con lz,s instrucciones que contiene el manual gel operador, • Limpieza o reparaciones deI motor (sistema de combustible) cuando se determina que se us6 combustible contaminado y oxidado (sarro). En general, et combustible debe usarse dentro de los 30 dias posteriores a su compra. • Deterioro y desgaste normal de los acabados exterioras o sustituci6n de r6tulos de productos. Esta garantia re otorga derechos legales espectficos, y usted tambi_n puede tenet otros dereohos que vat[an de un estado a otro. Sears Brands Management Corporation, Hoffman Estates, IL 60179 31 PELIGRO: Esta Maquina cortadora es capaz de amputar las manosy los pies y de lanzar objetos. si no se observan |as instruceiones de seguridad siguientes se pueden producir lesiones graves o ta muerte. _lb ADVERTENCIA: Con el fin de prevenir un arranque accidental cuando configure, transporte, ajuste o repare la m&quina, siernpre desconecte el cable de la bujia y coloque el cable deride no pueda entrar en contacto con la bujia. _I, ADVERTENOIA: No descienda per una colina en neutral, pues puede perder et control de la cortadora de cesped. _ADVERTENOIA: El escape deI motor, algunas de sus partes y ciertos componentes del vehfcu]o contienen o em_ten productos quimicos de los que se sabe en el Estado de California que causan c&ncer y defectos de nacimiento u otros daSos reproductivos. _ADVERTENOIA: Esta unidad no es para usarse con pesas para ruedas. Use s61o accesorios disehados especificamente para esta cortadora de c_sped. _I_ ADVERTENCIA: Los postes, las terminates y los accesorios relacionados de Ia baterfa contienen plomo y compuestos de plomo, productos quimicos de los que se sabe en el Estado de California que causan c&ncer y defectos de nacimiento u otros da_os reproductivos. I. OPERAGION GENERAL • Lea, entienda y siga todas las instrucciones sobre ta m&quina en el manual antes de comenzar, • No co]oque Jas manes ni los pies cerca de ias partes giratorias ni debajo de la m&quina. Mant_ngase alejade de la abertum de descarga en todo memento. • $61o permita que los aduitos responsables, que est_n familiarizados con las instrucciones, operen la m_.quina. • Libere el &rea de objetes come piedras, juguetes, cables, etc., pues podrian atraparse y lanzarse con la cuchilla. • AsegSrese de que el area est@libre de curiosos antes de operar la m_quina, Detenga la m_.quina si alguien entra en el &rea, • Nunca transporte pasajeros. . No corte en reversa, a menos que sea absolutamente necesario. Siempre mire hacia abajo y hacia atr&santes y cuando vaya en reversa. • Nunca dirija el material que se descarga hacia nadie. Evite descargar el materis] contra una pared u otra obstruccibn. El material puede rebotar hacia el operador. Detenga la cuchilla cuando cruce per superficies con grava, 32 • No maneje la m&quina si no tiene el colector de c_sped complete, la canaleta de descarga u otres dispositivos de seguridad en su Iugar y en fiJncionamiento. • Desacelere antes de dar la vuelta. • Nunca deje la m&quina en funcionamiento sin vigilar. Siempre detenga la cuchilla, active el freno de estacionamiento, detenga et motor y retire la Ilave antes de descender. • Desactive ]a cuchilla cuando no est6 cortando c_sped. Apague el motor y espere hasta que todas las partes so detengan per complete antes de limpiar Jam&quina, retirar el colector de c@spedo destapar la canaleta de descarga. • Opere la m&quina enicamente durante el dia o con buena luz artificial • No opere la m&quina mientras est_ bajo la influenciade alcohol o drogas. • Est6 pendiente del tr&fico cuando opere la m&quina cerca de caminos o al cruzarlos. • Tenga cuidado extreme cuando cargue o descargue Ia m_quina de un trailer o cami6n. • Use siempre protecci6n ocu[ar cuando opere la m&quina, • Los datos indican que los operadores de 60 6 m&sa5os de edad entran en un alto poroentaje de lesiones relacionadas con cortadoras do c_sped, Estos operadores deben evaiuar su habilidad para operar la cortadora de c6sped en forma suficientemente segura come para protegerse a s_mismos y a los dem&s de una lesi6n grave. • Mantenga la m_.quina libre de cualquier acumuiaci6n de e_sped, hojas u otra basura, pues podrian entrar en contacto con e] escape caliente y!o Ias partes del motor y quemarse. No permita que la plataforma de la cortadora de c_sped levante hojas u otra basura que pueda causar acumu]aciones. Limpiecualquier derrame de aceite o combustible antes de operaro almacenar la m&quina. Permita que la m&quina se enfrie antes de almacenarla, II. OPERACION EN PENDIENTES IlL NiI_IOS ]_as pendientes son un factor principal que se relaciona con Ia p6rdida de control y Josaccidentes de voicaduras, Io que puede dar come resultado una lesion grave o la muerte. La operaci6n en ted,s las pendientes requiere tener precauciones extras. Si usted no puede retroceder de una pendiente o si se siente inc6modo en la pendiente, no la pode. •Pode las pendientes hacia arriba y hacia abajo (a 15° come mdximo), no de un Iado a otro. • Tenga cuidado con los hoyos, surcos, protuberancias, piedras y otros objetos ocuitos. El terreno disparejo podr(a vofcar la mdquina. El c_sped alto puede esconder los obstdculos. - EUjauna velocidad terrestre baja de mode que no tenga que detenerse o girar mientras est_ en la pendiente. • Nocorte eWc_spedh_medo. Lasllantas pueden pettier su tracc(6n. • Mantenga siemprela m_.quina en una velocidad cuando baje per las pendientes. No cambie a neutral ni vaya en punto muerto hacia abajo en una colina. • Si (a m_.quina se para mientras sube per una colina, desactive la cuchilla, cambie a reversa y baje despacio. • Evite arrancar, parar o girar en una pendiente. Si las ]lantas pierden su tracci6n, desactive la cuchilla y proceda con lentitud en tfnea recta hacia abajo per la pendiente. • Mantenga todo el movimiento lento y gradual sobre {as pendientes. No haga cambios repentinos de velocidad o direcci6n, pues podHa causar que ]a mdquina se vuelque. • Tenga cuidaod extreme mientras opera la m_quina con colectores de c_sped u otros accesodos; pueden afectar [a estab]lidad de la m&quina. - No la use sobre pendientes pronunciadas. • No (ntente estabilizar Ia m&quina poniendo et pie en el sue]o. ° No corte cerca de deciives, zanjas o terraplenes. La m_.quina podr(a volcarse de repente si una rueda pasa sobre (a oriUa o si la or(lla termina en un hoyo. Pueden ocurrir accidentes trdgicos si el operador no est_ alerta ante (a presencia de ni_os. Con frecuencia (os niSos se sienten atraidos per la mdquina y la actMdad de corte de c_sped. Nunca d_ per un hecho que los ni_os permanecer_.n deride usted los v(o per 5ltima vez, • Mantenga a los niSos alejados delbrea de eorte y bajo la superv(siSn de un adulto responsable a parte del operador. ° Est_ aEerta y apague ta mdquina si un niSo entra en el &tea. • Antes y mientras avance en reversa, mire hacia atrds y hacia abajo per si hay ni(_os presentes. • Nunca I(eve niSosarriba dela mdquina, incluso cuando (a cuchilla est_ desactivada. Pueden caerse ylesionarse gravemente o interfer(r con la operaci6n segura de ta mdquina. Los niffos a quienes se les da una vuelta en la m_.quina pueden aparecer de repente en el &tea de corte para otra vuelta y set atrope]lados o golpeados con la m_quina. • Nunca permita que los nir_osoperen la m&quina. • Tenga cuidado extreme a] aeercarse a las curvas sin visibilidad, arbustos, drboles u otros objetos que puedan bloquearsu vision e Jmpedir observar a un nile. W. SERVIClO manejo seguro de la gasoUna Para evitar una Jesi6npersonal o un daSo en (a propiedad, tenga cuidado extreme al manejar ia gasolina. La gasolina es extremadamente inflamable y los vapores son explosives, • Apague los cigarrillos,habanos, pipas y otras fuentes de ignici6n. • Use s61o un recipiente de gasolina aprobado. • Nunca retire el tap6n de Ia gasolina ni agregue combustible con el motor en funcionamiento. Permita que el motor se enfrie antes de volver a Uenar e( tanque de combustible. • Nunca Ilene la m&quina de combustible en (nterieres. • Nunca a(macene la mdqu(na o el recipiente de combustible donde haya una flama abierta, chispa ouna (uz de p(loto come Ia de un calentador de agua u otros aparatos. 33 • Nunca ]lene los recipientes adentro de un vehiculo o en un cami6n o trailer con forte de pl&stico. Coloque siempre los recipientes en el suelo y Iejos de su vehiculo du_ante el Ilenado. • Retire el equipo qua flJnciona con gasolina del cami6n o trailer y rellOnelo en el suelooSi esto no es posible, entonces reIlene este equipo con un recipiente port&tiI, en lugar de hacerlo directamente con Ia boquilla del dispensador de gasotina. • Mantenga la boquilla en contacto con el borde del tanque o recipiente de combustible abri_ndote en rode memento basra qua el llenado de combustible est_ complete. No use un dispositivo que mantenga abierta Ia boquilla. • Si el combustible se derrama sobre la ropa, c&mbiesela de inmediato. • Nunca Ilene de m&s el tanque de combustible. Vuelva a colocar el tap6n de la gasolina y apri6telo bien, SERVICIO GENERAL - Nunca opere la maquina en un _.rea cerrada. • Mantengatodas]astuercas y pemos apretados para asegurarse de qua el eq uipo se encuentra en condiciones de trabajo seguras. • Nunca manipule los dispositivos de seguridad. Revise con regularidad que operen bien, • Mantenga Ia m&quinalibre de cualquier acumulaci6n de c6specl, he]as u otra basura. Limpie los derrames de aceite o combustible y retire cualquier basura que contenga combustible, Permita que la m&quina se enfrie antes de almacenarla. • Si usted golpea un objeto extrafio, det@ngase e inspecciona ia m&quina. Rep_.rela, de ser necesario, antes de volver a empezar. . Nunca haga ajustes o reparaciones con el motor en funcionamiento. • Revise !os componentes del colector de c_sped y la canaleta de descarga con frecuencia y sustituya con repuestos recomendados per el fabricante cuando sea necesario. - La cuchillade la cortaclorade c_sped tie_e file. Envuetva la cuchilla o use guantes y tenga precauci6n extrema cuando Ies d_ servicio. • Revise ta operaci6n deI freno con frecuencia. Ajuste y d_ servicio segt3n sea necesario. • Conserve o cambie las etiquetas de seguridad e instrucciones seg_n sea necesaxio. • Aseg_rese de que el &rea est_ Iibre de curiosos antes de operar la m_.quina. Detenga la m&quina si alguien antra en el &rea, • Nunca transporte pasKleros. • No corte en reversa, a menos que sea absolutamente necesario. Siempre mire hacia aba|o y hacia atr&s antes y cuando vaya en reversa. 34 ESPECIFICACIONES DEL PRODUCTO Capacidad de gasolina y Tipo: Tipo de Aceite (APi-SG-SL): Capacidad de aceite: 1,5 GaIlones (5,6 L) Regular sin pJomo ._ SAE 30 (Sobre 32°F/0°C) SAE 5W30 (Deabajo32OF/0_C 48 onzas Bujfa: Champion RC12YC (Abertura: .030"/0,76 ram) Marcha Adelante: 0 - 4/6,4 Atr&s: 0 - 2/3,2 Velocidad de Recarrido: _ph/Kph) Sistema de Carga :3 Amps Bateria PARA Congratu]acionesporsu buena compra. Su nuevo producto Craftsman® estd diseSado y fabric.ado para'_Jncionarde modo ffable por muchos aSos. Pero como todos los productos, puede neees_ar alguna reparacibn de tanto en tanto. En este ca.so tener un Acuerdo de Protecci6n para la Reparaci6n puede hacerles ahorrar dineroy fastidios. Compre ahora un Acuerdo de Protecci6n para la Reparaci6n y prot6gese de mo]estias y gastos inesperados. Un Acuerdo incluye los puntossiguientes: ° Servicio experto de nuestros12.000 especialistas profesionales en la reparaci6n. * Servicio i|imitado sin cargo alguno para las partes y ta mano de obra sobre todas Ias reparaciones garantizadas. Torque deI perno 45-55Pies/lJbras(62-75Nm) de la ¢uchilla: FELICITACIONES pot la compra de su cortadora de c_sped. Ha sido diseSado, planificado y fabricado para darle ta mejor confiabiJidad y et meier rendimiento posible. En el caso de que se encuentre con cualquier problema que no pueda solucionar fdcilmente, haga el favor de ponerse en contacto con un centro de servicio Sears o con un otto centro de servicio cualificado. Cuenta con representantes bien capacitados y competentes y con las herramientas adecuadas para darle servicio o para reparar este cortadora de c_sped. Haga el favor de leer y de guardar este manual. Estas instruc-ciones le permitir&nmontar y mantenet su unidad en forma adecuada. Siempre observe las "REGLAS DE SEGURIDAD." RESPONSABILIDADES ACUERDOS DE_ PROTECClON LA REPARACION DEL CLIENTE • Lea y observe las reglas de seguridad. • Siga un progmma regular at darle mantenimiento, cuidados y uso a su cortadora de c_sped. • Siga Ias instrucciones de las secciones de "Mantenimiento" y '_.lmacenamiento" de este manual del propietario. _IbADVERTENClA: Esta cortadora de cL=s _ pedestd equipada con un motor de combusti6n interna y no se debe usar en o cerca de terrenos cubier_osde bosques sin mejoras, cubiertosde arbustos o cubiertos de pastos, a menos que el sistema de escape de] motor est_ equipado con un parachispas que cumpla con Ias leyes locales o estatales aplicables (de habedas). Si se usa un parachispas, el operador deberd dade mantenimiento en un orden de trabajo efectivo. En el estado de California, las Ieyes exigen el uso de un parachispas (Secci6n 4442 de| C6digo de Recursos P0blicos de California). Otros estados pueden tener leyes similares. En los terrenos federales se ap]ican las ]eyes federales. Se puede obtenerun parachispasparae[silenciadoratrav_s del centro de servicio autorizado rods cercano. 35 * Sustituci6n del producto si su producto garantizado no puede set arreglado. , Descuento de110% sobre el precio corriente del eervicio y de las partes refativas al servicio no cubiertas por el acuerdo; tambi_n el 10% menos sobre el precio corriente de un control de mantenimiento preventivo. - Ayuda rdpida por tel_fono- soportetelef6nico por parte de un representante Sears sobre productosque requieren un arreglo en casa, y adem&s una programaci6n sobre los arreglos mas convenientes. Cuando se ha comprado el Acuerdo, basta con unaIlamadatelef6nica para programarel servicio. Puede Ilamar cuando quiera, dJa y noche o fijar en linea una cita para obtener el servicio. Sears tiene rods de 12,000 especialistas profesionales en Ia reparaci6n, que tienen acceso a rods de 4.5 millones de partes y accesorios de calidad. Este es el tipo de profesiona]idad con que puede contar para ayudar a alargar la vida del producto que acaba de comprar, por muchos aries. iCompre boy su Acuerdo de Protecci6n para Ia Reparaci6nJ Se aplican algunas limitaciones y exclusiones. Para conocer los precios y tener rods Informaci6n, llame al 1-800-827-6655. SERVICIO DE INSTALACION SEARS Para la inetalaeidn profesional Sears de aparatos de casa, puertas de 9araje, calentadores de agua y otros importantes articu]os para la casa, en U.S.A IJamar a 1-800-4-MY-HOME@ Volante (t) Parachoques de la direcci6n traseros (t) Pamchoques delanteros de direcci6a (1) 5/t6-18 x4 Pemo de cabeza (1) Arandela de seguridad -Cobe_tura hexagonal (4) Tomillo #t0 x 0,200 E×tenci6n Adaptador (1) Shroud (1) Arandela (1) Arandeias taza D (2)Llave Hoja de pendiente Asiento (1) Manilla de ajuste Su nueva cortadora de c@sped se ha ensarnblado en la f&brica con excepci6n de aquellas partes que se dejan sin ensamblar para eJenvio. Para asegurar la operaci6n segura y correcta de la cortadora de c6sped, todas las partes y la ferreteria que usted ensamble se deben apretar bien. Use las herramientas correctas necesarias para asegurar un ajuste apropiado. HERRAMIENTAS NECESARIAS EL ENSAMBLADO PARA El ensamblado ser& m#,s simple si cuenta con un conjunto de llaves de cubo. Los tamarios de I[ave est#tndar que necesitase indican en seguida. (1) Llave de 1/2" (I) Herramienta de cuchilla (1) Calibrador de presi6n para Ilantas Cuando se menciona la derecha o la izquierda en este manual, esto significa cuando usted se encuentra en Ia posicibn de operaci6n (sentado al volante). RETIRO DE LA CORTADORA DE LA CAJA DE CARTON NOTA: $61o corte la caja de cart6n con una herramienta de cuchilla corta, pues una de cuchilla larga o una sierra pueden pinchar Tas Ilantas de la unidad. COMO CONFIGURAR SU CORTADORA DE ClaSPED REVISE LA BATERiA AsegSrese de que la bateria est@bien sujetada, y que todos los cables est_n bien conectados. • • La bateria est_ ubicada debajo del asiento. La bateria se ha cargado por completo en la fAbriea antes de su instalaci6n. CF_SPED DE DESEMPACADO DE LACAJA DE CARTON t. Retire todas Ias partes sueltas aecesibles y las cajas de las partes deI cart6n. 2. Corte las lineas punteadas de los cuatro paneles de Ia caja de cart6n. Retire la caja de cart6n y el marco superior come una sola pieza, 3, Retire los matedales de empaque de Ia cortadora de c6sped, 4, Revise si hay cualquier parte sueltao cartones adicionales y retfrelos, 36 • Aslento teria PARA INSTALACI6N DE COLUMNA DE DIRECCION 6. 7. Deslice eI eje de extensi6n sobre el eje de direcci6n. Des]ice ia cubierta de espuma de protecci6n del eje de direcci6n sobre el eje de direcci6n. 3. Coloque eI manguito de direcci6n sobre e] eje de direcci6n y empSlejo hacia abajo para asegurarlo. 4. Coloque Iasruedas delar_erasde [acortadora de cL=sped de mode que apunten en Ifnea recta hacia adelante. 5. Retire el adaptador del volante y deslice el adaptador sebre el eje de direcci6n. 7. Presione el volante en su posici6n sobre el eje, instale Ia arandela grande, bIoquee ta arandela y apriete bien el perno. 8. Coloque bien el inserto deIvolante en eI centre del volante, 2, 8. 9. Baje el asiento a la posici6nde operaci6n y si_ntese en el asiento. Deslice el asiento hasta que I[egue a una posici6n c6moda, que ]e permita presionar eI pedal deI embrague/freno completamente hasta abajo. Desmbntese del asiento sin mover su posici6n ajustada. Levante el asiento y apriete ta manilla de ajuste en forma segura, Base del Asiento Perno Arandela_ Inserto planagrande j_-_ Volante de direcci6n_ ...... "-_ "r-'-- =._x.\. de ladirecci6n---'-_ _ Cubierta ° "_ Manilla de Adaptador //_ Eje de /#"_... /_ PARA INSTALACI6N NOTA: Ahem puedesacar la cortadorade c6sped de latarima. Observe las siguientes instrucciones apropiadas para retirar la cortadora de c_sped de la tarima, Ejede _-direcci6n ADMERTENCIA: Antes de empezar, lea, entienda y siga todas las instrucciones de la secci6n de Operani6n de este manual. AsegSrese de que la cortadora de cL,sped est_ en un &rea bien ventilada, Aseg_rese de que el &rea de enfrente de la cortadora de c_sped est_ libre de gente y objetos. DEL ASIENTO Ajuste el asiento antes de apretar la manilla de ajuste. 1. Remueva [a manilla de ajuste y la arandeta plana que aseguran el asiento aI empaque de cart6n y p6nga[os de lade para poder utilizarlos durante la instalaci6n del asiento sobre el tractor. 2. Remueva y desechese del embalaje de cart6n. 3. Colocar el asiento y en el asiento del recipiente de manera que la tres (3) cojins est_ posicionada en el agujero ancho ranurado en el recipiente, 4. Empujar en el asiento para enganchar eI cojins en la ranura y ernpujar el asiento hacla la parte tra_serade1tractor, 5. Pivotear el asiento y el recipiente hacia adelante y ensamblar el bot6n de regulaci6n y la arandela taza de mode no fuerte. No apretar enroscar fuerte, PARA SACAR LA CORTADORA DE ClaSPED DE LA TARIMA (Consulte Ia secci6n de Operaci6n para ver la ubicaci6n y funci_n de los controles) 1, Eleve lapatanca delelevador de Ia plataforma hasta su posicibn m_xima, 2, Sue[te el freno de estacionamiento al Iiberar et pedal deI embrague_eno. 3. Cambie unidad a la posicidn de neutro. 4, Saque la cortadora de c_sped de ]a tarima, 37 COLOCACION DELANTERA DE LA DEFENSA NOTA: Para que el armado le resulte senciIIo, puedesolicitar ayudaa otra persona cuando monte la defensa en la cortadora de c_sped. 1. Retire los tornillos (2) deI chasis delantro de la cortadora de c_sped. 2, Incline la defensa delantera de modo que las pestaSas de la defensa entrenen las ranuras del frente del chasis y baje la defensa hacia su tugar. Coloque Ia defensa en el frente del chasis con los tornillos que retir6 en el paso t. Apriete bien los dos (2) tornJll0s. 3. 4. REVISE LA PRESION DE LAS LLANTAS Las Ilantas de la cortadora de c6sped se inflaron de rn&s en la f&bdca para su transporte, Corregir la presi6n de las Ilantases irnportantepara obtener el mejor desernpeSo deI corte. • Reduzca la presi6n de tas Ilantas a Ia PSI que se rnues_traen las llantas. REVISE LA NIVELACION DE LA PLATAFORMA Para obtener los rnejores resultados de corte, la carcasa de lacort_dorade c@spedse debe nivelar bien. Consulte la parte de "NIVELACION DE LA CARCASA DE LA CORTADORA DE CESPED" en ta secci6n de Servicio y Ajustes de este manual, 5. 6. Coloque fa envoitura de pl_.stico sobre la defensa conforrne se muestra y ens&mbleta holgadarnente en Ia defensa con los euatro (4) tornill0s provistos. Apriete bien los cuatro (4) tornitlos. Envoltura COLOCACION DELADEFENSATRASERA NOTA: Para que el arrnado le resulte sencillo, puede solicitar ayudaaotrapersonacuando mente Ia defensa en la cortadora de c@sped. 1. Retire los tornillos (4) del chasis trasero de la cortadora de c_sped, 2. Coloque la defensa eonforme se muestra y ensAmblela en el ehasis trasero con Ios tornillos que retir6 en el paso 1. 3. Apriete bien los cuatro (4) tornillos. 38 REVISE LA POSlClON CORRECTA DE LA CINTA DEL IMPULSOR DE LA CORTADORA DE CESPED Observe la figura que se rnuestra para cambiar la cinta deI irnpulsor de la cortadora de c_sped en la secci6n de servicio y ajuste de este manual. Verifique que la cinta est6 en la ruta correcta. REVISE EL SISTEMA DE FRENO Despu@sde que haya aprendido c6mo operar su cortadora de c6sped, revise que el freno funcione bien. Consu3te la parte de '_,JUSTE DE FRENO" en lasecci6n deServicio yAjustes deeste manual. t_LtSTA DE REVISION Antes de operar su nueva cortadora de c6sped, deseamos asegurarnos de que usted obtenga el mejot desempeSo ysaUsfacci6nde este Producto de Calidad. Por favor revise la siguiente lista de revisi6n: J Todas Ias instrucciones de ensamblaje se ban completado. •/ No queda nhguna parte suelta en ]a caja de cartbn. La bateria est& bien conectada. J ,/ Et asiento est& ajustado c6modamente y bien apretado. ,/ Todas las Ilantas estdn bien infladas. (Las Ilantas se inflan de m&s en [a f&brica para su transportaci6n.) ,/ AsegQrese de que la plataforma de lacortadora de c_sped est_ bien nivelada de lado a lado y del frente a la parte posterior para obtener los mejores resultades de corte. (Las Ilantas deben estar bien infladas para ia nivelaci6n.) €" Revise la cinta de la cortadora de c(_sped. Aseg_rese de que est_ en la ruta c0rrecta alrededor de las poleas y adentro de todas las sujeciones de la cinta. •/ Revise el cableado. AsegSrese de que todas [asconexiones est6n bien co]ocadas y que los cables est_n bfen sujetos. AI aprender c6mo usar su cortadora de c_sped, preste atenci6n extra a los siguientes puntos importantes: ,/ Elaceite deI motorest_ en un nivel adecuado. ,/ ,/ ,/ ,/ El tanque de combustible est_ lleno con gasolina sin plemo regular nueva y limpia. Familiar|cese con todos los controles, su ubicaci6n y funci6n. Op_re[os antes de arrancar el motor. AsegQrese de que el sistema de freno est_ en condiciones de operaci6n seguras. Asegurarse de que el Sisterna de Presencia del Operador y el Sistema de Funcionamiento Atr&s (ROS) funcionan de modo adecuado (Ver las Secciones de Funcionamiento y Mantenimiento en este manual.) 39 Estos simbolos pueden aparecer en ta cortadora de c_sped o en Ia literatura provista con el producto, Aprenda y entienda su significado. R MAP_CHA N ATR._S H NEUTRO 8AJO I, al41 6 MOTOR APAGADO ESTRANGULAOI6N MOTOR ENCENDtCO MOTOR ENMARCHA ACCESORIO DEL EMBRAGUE ENGANCHADO LENTO INTERRUPTER BE IGl',_,lC[(:) N PRESION FRENO DEL ACE|TE MANe DE FRENO SE CERR(_ DE MANO ABIERTO (SOS) ;i; BOB£E LUZ DE TEMPERATURAS R,_'PIDO G SISTEMA FUNCIONAM[ENTO ATR_,B i\1 L ALTO COMBUSTIBLE PRESI_,N DEL ACE_E ACCESORIO DEL EMBRAGUE DESENGANCHADO BATERiA MARCHA ATRP, S PELIGRO, GUARDE LAB MANOSY LOS PIES LEJOS + MAROHA HAC|A AOELANTE ALTURA DE LA SEGAOORA MANTENGA EL AREA DESPE, JADA LEVANTAMIENTO DE LA SEGABORA PELIGROS DE PENDIENTES (YeaIa secci6n_e las reglasde segurJdad) CONTROLOE DESAC_VAOO RUEDA MBRE ADVERTENCIA indica un peligro que, si no Be evita, puede provocar muerte o lesiones graves. FRENOtEMBRAGUE PEDAL PELIGRO indica un peligro que, si no se evita, proveca muerte o lesiones graves. DE PRECAUCI()N indica un peligro que, si no se evita, puede provocar lesiones ligeras o moderadas. CONTROLDE RUEDA UBRE ACTWADO No seguir las siguientes instrucciones puede provocar heridas o muerte. Los sfmbolos de aviso de seguridadse utilizan para identifiear informaciones de seguridad relativas a peligros que puedenprovocar ta muerte, heridas graves y/o dafios a la ma.quina. PRECAUCI(_N se utiliza sin elprovocar sfmbolo de aviso, indica unacuando situaeJ6n que puede da_os al tractor y/o al motor. SUPERFICIES CALIENTES indica un peligro que, si no se evita, puede provocar la muerte, lesiones graves yto danes a la mdquina. FUEGO indica un peligro que, si no se evita, puede provocar la muerte, lesi0nes graves y/o danes a Ia mdquina. 4O CONOZCA SU CORTADORA DE ClaSPED LEA ESTE MANUAL DEL PROPtETARIO Y LAS REGLAS DE SEGURIDAD ANTES DE OPEPAR SU CORTADORA DE ClaSPED Compare las ilustraciones con su cortadora de c_sped para familiarizarse con las ubicacionesde los diferentes controles y ajustes, Conserve este manual para futuras consultas. Pedal dei freno Freno de (ROS) en posici6n "on" Palanca del embrague de Ia E_mbolode la palanca del =ptor de arranque Aceleraci6ni EstrangulaoiSn de ajuste de altura de controlde movimiento Nuestra cortadorade c6spedcumple con las normasde seguridad aplicables de] Institute Nacional Estadounidensede Normas. PALACA DEL EMBRAGUE DE LA PLATAFORMA - Se usa para activar la cuchilla de la cortadora de c_sped. PALANCA DE FRENO DE ESTACIONAMIENTO - Fija el freno de estacionamiento en la posici6n de freno. PALANCA DE CONTROL DE MOVIMIENTO Selecciona lavelocidad y direcci6n de la cortadora de c_sped. |NTERRUPTOR DELSISTEMA DE FUNCIONAMIENTO HACIA ATRAS (ROS) EN POSICI6N "ON" - Permite laoperaci6n delconjuntosegador o otroaccesorioaccionado mientrasqueen rev_s. CONTROL DEACELERACION/ESTRANGULACION - Se usa para hacer arrancar y controlarla velocidad deI motor. FRENO DE ESTACIONAMIENTO- Se usa para frenar la certadora de c6sped y arrancar el motor, PALANCA DE AJUSTE DE ALTURA - Se usa para ajustar Ia altura de corte de Ia cortadora de c@sped. INTERRUPTER DE ARPANQUE - Se usa para arrancar y detener e[ motor. I_MBOLO DE LA PALANCA DEL ELEVADOR Se usa para soltar la palanca de ajuste de altura cuando se cambia su posioi6n. 41 La operaci6n de cualquier cortadora de c_sped puede causar que entren objetos extraEos en los ojos, 1oque puede provocar un daEo severe en los mismos. Use siempre lentes de seguddad o protecciones oculares mientras est_ operando la cortadora de c_sped o realizando cualquier ajuste o reparaci6n. Se recomienda usar una careta de seguridad de visi6n amplia sobre los anteojos o lentes de seguridad est&ndar. COMO USAR LA CORTADORA DE CESPED ACTIVAClON DEL FRENO DE ESTACIONAMIENTO IMPULSI6N DE RECORRIDO - La cortadora de c_sped est_ equipada con un interruptor de detecci6n de presencia del operador. Cuando el motor est_ en funcionamiento, cualquier intento del operador de dejar el asiento sin primero activar eJfreno de estacionamiento apagara el motor. 1. 2. Presione el pedal deI freno completamente hasta abajo y mant_ngalo presionado. Jale y sostenga la palanca del freno de estacionamiento hacia arriba, libere la presibn del pedal de freno y {uegosuelte Ia palanca de! freno de estacionamiento. El pedal debe permanecer en posiciEn de frenado. Aseg6rese de que el freno de estacionamiento mantendr& detenida la cortadora de c6sped. * Para parar el mecanismo impulsor,presione el pedal del freno completamente. , Mueva la palanca de control de movimiento a la posici6n de neutro. q ._._____----Palancade controlde movimientc_ MOTOR • Mover Ia palanca de mando entre la posici6n de velocidad media y m&xima (r&pida). AVISO:Si no se mueve la palanca de mando entre Ia posiciEn de velocidad media y m_xima (r&pida), antes de pararse, se puede causar un "retorno de llama" deJ motor. Control De Acelemci6n PARADA CUCHILLA DE LA CORTADORA DE C_:SPED • Para detener la cuchitta de la cortadora de c_sped, mueva ]a palanca det embrague de !a plataforma a Ia posici6n de "desactivada". • Gire la Ilave de ignici6n a la posici6n de apagado "STOP" y remueva la llave aI abandonar e] cortadora de c_sped para evitar el uso no autorizado. IMPORTANTE: Dejando e[ interruptor de la ignici6n en cualquier posici6n otra que "STOP" causar i que la bateria se descargue (muerta). AVISO: Bajo ciertas condiciones, cuando el cortadora de c_sped est& parade con el motor andando en vacio, los gases de escape deI motor catiente pueden hacer que el c_sped se ponga "caf_." Para eliminar esta posibilidad, siempre pare el motor cuando pare el cortadora de c_sped en &teas con c_sped. _ PRECAUCI6N: Siempre pare el cortadora de c_sped completamente, seg6n se ha descdto anteriormente, antes de abandonar la posicibn det operador, (I_) "Enganchado" (Engaged) (1"_) "Desenganchado" (Disengaged) 42 PARA USAR EL CONTROL ACELERACION DE LA Eltango de altura de cortees de aproximadamente 1-1/2 a 4". Las alturas se miden desde el suelo hasta la punta de la cuchi]la con el motor sin funcionar. Estas alturas son aproximadas y pueden radar segdn las condic]ones de] suelo, laalturade[ c_sped y Iostipos de c@spedesque sevan a cortar. ° EIc_sped promedio se debe corr.araproximadamente a 2 i/2" (6.35 cm) durante la temporada frfa y a m_.s de 3" (7 cm) durante los meses de calor. Para que el c_sped crezca m&s sano y tenga mejor aspecto, cbrtelo con frecuencia y despu@sde un crecimiento moderado. • Para un mejor rendimiento del corte, el c_sped de m&s de 6" (I5.20 cm) de aItura debe cortar dosveces. Hagael primercorte relativamente alto; el segundo deber& ser a laaltura deseada. Siempre opere el motor a una aceleraci6n completa. . Si el motor funciona a unaveIocidad ]nfedor a la mbxima (r&pida), su rendimiento disminuye. • El rendimiento 6pUmose obtiene alavelocidad mdxima (r&pida). Control De Aceleracl6n OPERACION C_SPED MOVIMIENTO HAClA ADELANTE HACIA ATRAS DE La cortadora de c_sped estd equipada con un interruptorde detecci6n de presenciadeloperador. Cualquier intento del operador de dejar el asiento conel motor en funcionamientoyel embraguede la plataforma activado apagardel motor. Usteddebe permanecer colocado por comp{eto en el centro del asiento para evitar que el motor se desoriente o se apague cuando opere el equipo sobre un terreno lieno de baches u ondulante o en colinas. 1, Seleccione la altura de corte deseada, Y La direcci6n y Ia velocidad del movimiento se controla por medio de fa palanca de control de mevimiento. 2. 1. Aseg_resede que elfreno deestacionamiento est_ aotivado, 2, Arranque la cortadora de c@spedcon la palanca de controlde movimiento en Ia posicibn neutral (N), 3. Libere el freno de estacionamientoo 4. DE LA CORTADORA Active ]a euchilla de la cortadora de c_sped at accionar Ia palanca del embrague de Ia plataforma. PARA DETENER LA.CUCHILLA DE LA CORTADORA DE CESPEDDesactive la palanca plataforma. Mueva lentamente la palanca de control de movimiento a Ia posiof6ndeseada. Posici6n de "desactivada" de Ia palanca de[ embrague de Ia p]ataforma n_ovimiento del embrague de la Posic[6n alta de ajuste de a]tura de la cortadora de \ AJUSTE DE LA ALTURA DE CORTE LA CORTADORA DE ClaSPED DE La posicibn de la palanca de] elevador de la plataforma de la cortadora de c_sped determina la altura de corte. PosiciSn de "act_vada" de la palanca del embrague de la plataforma • Agarre la palanca del eievador, ° Presione el @mbo[ode la palanca del elevador con et pulgar y rnueva ta palanca a la posici6n deseada. & PRECAUCI6N: c_sped sin e] colector cortadoras de c_sped la coraza del deflector 43 baja de ajuste de altura de Ia cortadora de c_sped No opere la cortadora de de c_sped entero, en las equipadas con _ste, o sin en su sitio. Correa el&stica Oorazadel deflector Cor_a eI_stica Oubierta de Ia alcochadora Cubiertade ta alcoch_dora FUNOIONAMIENTO ATRAS (ROS) Su cortadora de c@sped est& equipada con un Sistema de Operaci6n en Reversa (SOR). CuaP quier intento pot parte deI operador de avanzar en reversa con el embrague de la plataforma activado apagar& el motor, a menos que Ia llave de encendido est6 en la posici6n de "ENCENDIDO" (ON) deI SOR 3. Coloque bisagra. el deflector en la abrazadera 4. Coloque la cubierta de paiote sobre el deflector, Soporte de Ia bisagra _llJ ADVERTEN CIA: lr marcha atr_.scon el embrague puesto para cortar, no es recomendable. Poniendo el ROSen posici6n "ON", para permitir el funcionamiento atr,_s con el embrague pues_o, se tiene que hacer s6Io cuando el operador Ioconsidem necesario para reposicionar Jam&quina con el dispositivo embragado. No siegoe en rev_s a menos que sea absolutamente necesario. USA R EL SISTEMA DE FUNCIONAMIENTO ATRAS 4. 5. Mover despacio la palanca de mando del movimiento hacia la posici6n atr&s (R) para empezar el movimiento. Cuando el uso del ROSes m&s necesario, d@ vuelta a la llave de ignici6n en el sentido de tas agujas del reloj hasta Ia posici6n "ON". Posiei6n ROS "ON" COLOCACION 1. 2, deflector 5. Utilice elcortadora de cesped solamente si est& seguro de que no ingresar_n nif,os ni otras personas o animales al &rea donde se va a cortar el c_sped. 1. Mover Ia palanca de mando deI movimiento en la posici6n neutro (N). 2. Con el motor en marcha, girar la Ilave del interruptor de Ia ignicidn en el sentido inverso al de las agujas del reloj hasta la posici6n "ON". 3. Mire hacia abajo y hacia atr&s no s61o antes de ir marcha atrAs, sino mientras est@yendo marcha atrzts. DEL DEFLECTOR Cotoque la correa el&stica 1 desde el deflector a la plataforma. Coraza del deflector OPERACION A CubJefta de la alcochadora EN COMNAS ADVERTENCIA: No conduzca hacia arriba o hacia abaio en colinas con pendientesmayores de 15° y noconduzca de un Iadoa otroen ninguna pendiente. Use Ia guia de pendientes de la parte posteriorde este manual. • Elija la velocidad m&s tenta antes de comenzar a bajar o subir colinas. • Evite detenerse o cambiar de velocidad en las colinas. • Si es absolutamente necesado detenerse, empuje con rapidez el pedal del embrague! freno a la posici6n de freno y active el freno de estacionamiento. • Mueva la palanca de control de movimiento a la posici6n neutral (N). • Pare reiniciar e] mavimiento, suelte despacio el freno de estacionamiento y el pedal del embragueifreno. Motor en posici6n "ON" (Operaci6n Normal) Desenganche las 2 correas el&sticas de la plataforma a la cubierta de pajote. Levante la cubierta de pajote. D@todas las vueltas despacio. 44 de TRANSPORTE At empujar o remolcar ta cortadora de c_sped, asegQrese de desactivar latransmisi6n al colocar la palanca de velocidades en neutral • Eteve el ajuste de altura de la cortadora de c@sped a su posici6n m&s alta con la palanca de ajuste de altura de Ia cortadora de c@sped. • Para volver a actJvar la transmisi6n, presione el freno y cambie la palanca de velocidades de neutral a otra posici6n. ANTES MOTOR DEL ARRANQUE REVISE MOTOR EL NIVEL DEL DE ACEITE DEL El motor de ta cortadora de c_,sped se envla desde la f&brica ya Ilena con aceite de peso para el verano. 1. Revise el aceite del motor con ta cortadora de c_sped sobre un suelo nivelado. 2. • - Retire el tap6n/la varilla de Ilenado de aceite y limpiela con un patio, reinserte la vari[Ia y atornitle bien el tap6n, espere unos cuantos segundos, retirelo y verifique el nivel del aceite. Si es necesario, agregue aceite hasta que Ilegue a la marca que dice "LLENO" en la varilla. No Io llene de re&s. Para operarlaenclimafrio, usted debe camblar el aceite para obtener un arranque m&s f&ciI (Consulte la tabla de viscosidad de aceite de ta secci6n de Mantenimiento de este manual). Para cambiar el aceite deI motor, consulte la secci6n de Mantenimiento en este manual COMO AGREGAR GASOUNA • Llene eltanque de combustible hasta la parte inferior del cuello de relleno. No Io Ilene de rods. Use gasolina sin plomo regular nueva y timpia con un minimo de 87 octanos. (Usar gasolina con plomo incrementar&los dep6sitos de carbono y 6xido de plomo y reducird la vida de la v&lvula), No mezcle aceite con gasolina. Compre combustib]een cantidades que se puedan usaren 30 dias para asegurar il_ltla frescura del combustib[e. PRECAUCI6N: Limpie cualquier derrame de aceite o combustible. No almacene, derrame ni use gasolina cerca de una flama abierta. _1_ PRECAUCI6N: Los combustibles mezcla- dos con alcohol (lIamados gasohol o que usan etanol o metanoI) pueden atraer la humedad, Io que provoca la separacibn y formaci6n de _cidos durante e] almacenamiento. El gas &cido puede dafiar el sistemade combustiblede un motor mientras se encuentra en almacenamiento. Para evitar problemas con el motor, el sistemadecombustible se debe vaciar antes deI almacemaniento d urante 30 dfas o m&s. Drene el tanque de gasolina, arranque et motor y hdgalo funcionar hasta que las lineas de combustible y el carburador est_n vac{os. Use combustible nuevo en la pr6xima temporada. Consu[te las Instrucciones de Aimacenamiento para obtener informaci6n adicional. Nunca use productos limpiadores para motor o carburador en el tanque de combustible porque puede ocurrir un dafio permanente. PARA HACER ARRANCAR EL MOTOR AI hacer arrancar e] motor por la primera vez o si se ha acabado el oombustible del motor, se necesitard tiempo para e] arranque extra para mover el combustible desde el estanque hasta el motor. • Si_ntase en el sill6n en la posici6n de operaci6n, suelte el pedal del freno y ponga el freno de estacionamiento. • Ponga la palanca de control de movimiento en la posici6n de neutro. • Mueva el embrague de[ accesorio a Ia posici6n "DESENGANCHADO". • Mueva la palanca de control de la aceleraci6n a la posici6n de estrangulaci6n. AVISO: Antes de arrancar, lea las instrucciones siguientes para el arranque en clima fr[o y templado. • lnserte Ia llave en Ia ignici6n y gire la ilave en el sentido que giran tas mani[tas deI reloj a la posici6n de arranque start, y sue[re la Ilave tan pronto como arranque el motor. No haga funcionar el arrancador continuamente por m_is de quince segundos pot minuto. Si el motor no arranca despu_s de varios intentar]os, mueva e[ control de la aceleraci6n a la posici6n de r&pido, espere unos cuantos minutos y trate de nuevo. Si el motor sigue sin funcionar, mueva el control de la aceleraci6n a la posici6n de estrangulaci6n y intente de nuevo. ARRANQUE CON TIEMPO TEMPLADO (50° F/I 0°O Y MAS) , Cuando arranque el motor, mueva el control de la aceleraciSn a la posici6n de r&pido. • Ahora puede usar el mecanismo de desplazamiento. Si el motor no acepta la carga, vuelva a encender el motor y permita}e que se caliente durante un minuto usando el ahogador conforme se describe arriba. Combustible de tapa \ 45 ARRANQUE CON TIEMPO FRiO (50 ° F/IO°C Y MENOS) ° AI hacer arrancar el motor, mantenga el control de Ia aceleracion a la posfci6n de estrangulaci6n hasta qua el motor se caliente y empieze fundonar maI. Una vez que ernpieze a funcionar mat, mueva inmediatarnente el control de la aceIeraci6n a fa posici6n r&pida. El calentamiento del motor puede tomar a partir de varios segundos a varios rninutos (cuanto rn&sfrfa es la ternperatura, rn_s largo es el catentarniento). OONSEJOS PARA CORTAR EL ClaSPED La cortadora de c_sped debe estar bien nivelada para que su desempeSo sea.el mejor. Consulte la parte de "NIVELACION DE LA CARCASA DE LA CORTADORA DE CESPED" en ta secci6n de Servicio y Ajustes de este manual. • El lado izquierdo de la cortadora de c6sped se debe usar para podar. Conduzca de manera qua los recortes de descarguen sobre el _.rea que ya se ha cortado. Et &tea de corte debe estar del lado derecho de la cortadora de c_sped. Esto crear& una distribuci6n m_.s uniforrne de los recortes y un corto rn&s uniforrne. • f • • • Cuando corte &reas grandes, cornience girando hacia la derecha, de modo qua los recortes se descarguen [ejosde los arbustos0 bardas, carninos, etc. Despu@sde una o dos vueltas, corte en la direcci6n opuesta, dando vueltas hacia la izquierda hasta que terrnine. Si el c6sped est& dernasiado alto, so debar& cortar dos veces para reducir ta carga y Ja posibilidad de un peligro de incendio 13orlos recortes secos. Haga el pdmer corte relativamonte alto; el segundo debar& sera la altura deseada. No corte el c@sped cuando est@h_medo. E[ cesped hSrnedo taponarA la cortadora de c6sped y dejar_ rnatas indeseables. Permita que el c_sped se seque antes do podarlo. Regule ta velocidad terrestre at solecci0nar un avance 1osuficientemente lento para ajustar el desernper_o de corte de ia cortadora de c_sped asi como la calidad del corte deseada. Cuando utilice accesorios, seleccione una ve[ocidad terrestre que se adapte al terreno y obtenga el rnejor desemper_o del accesodo qua est@usando. 46 ANTES DE CADA USO 1. Revise el nivel del _ceite del motor. 2. Revise I_ operaci6n det freno. 3. Revise la presi6n de las Ilantas. 4. Revise que los sistemas de presencia deI opemdor y de ROS funcionen bien. 5. Revise que los broches no est_n sue]tos. RECOMENDACIONES GENERALES La g_rantla par_ esta cortadom de c_sped no amparalos articulosquese hansometido alabuso o la negligenciadetoperation. Pare recibirel valor completo de la garantia, el oper_dor debe darle mantenimiento _lacortadoradec_sped conforme se indica en este m_nual. Ser& necesario hacer algunos ajustes en forma peribdica para mantener de manera correcta la cortadora de cf_sped. IMPORTANTE: No aceite ni engrase los puntos de los pivotes que tienen coj!netes de nailon especiales+ Los lubricantes wscosos atraer_.n el polvo y la suciedad, 1oque reducird ta vida de los cojirtetes autelubricantes. Si siente que se deben Iubricar, use s6Io un lubricante tipo grafito en polvo moderadamente, AI rnenos unavez cadatemporada, revise si usted debe hacer alg_n ajuste conforme se describe en la secciSn de Servicio y Ajustes de este manual. . AI menos unavez aIaSo usteddeber_;cambiar [a bujfa, limpiar o cambiar el filtro de aire y revisar si Ia cuohillay la cinta est_n desgastadas. Una nuew bujla y un nuevo filtrode aire aseguran la mezcla adecuada de aire y combustible, Io que ayuda a que el motor funcione mejor y dure m_s tlempo+ 47 CORTADORA DE CESPED Siga s+empre las reglas de seguridad cuando realice cualquier mantenimiento+ OPERACION DEL FRENO Si Ia cortadora de c@sped requiere m_.s de cuatro (4) pies (t +219 metros) para detenerse a la velocidad m_txima sobre una super_cie de concrete o pavimento seco nivelado,entonces se debe dar servicio al freno en el centre de servicio autorizado m&s cercano, LLANTAS • Mantenga Ia presi6n de las Ilantas a t 2 PSI. - Mantenga Ias t+antas tibresde gasolina, aceite o quimicos para el control de insectos, pues pueden dar_ar el caucho+ • Evite los palos, las piedras, los surcos profundos, objetos fi[osos y otros peligros que pueden causar daSo en Ias llantas. NOTA: Para sellar las pinchaduras de [as Ilantas y prevenir Ias Ilantas desinfladas debido a fugas lentas, puede comprar sellador de Ilantas con el distribuidor de partes local. El sellador de llantas tambi6n previene la podredura en seco y la corrosion de las Uantas. EJE Y HUSOS • Los ejes de las ruedas frontales y los husos frontales se deben lubricarbien. ° Los ejes de Ias ruedas se deben lubricar con un lubricante tipo grafito en polvo seco. , Nunca opere la palanca del embrague de ]a plataforma a menos que est_ sentado en el asiento VER[FIEZ SISTEMA FUNCIONAMIENTO ATRAS (ROS) • Cuando el motor est_ en marcha con el interruptor de llave en posiciSn de motor "ON" y e/ embrague det accesorio conectado, cualquier tentativa de[ operador de viajar marcha attics, apagar& el motor. • Cuando el motor est_ en marcha con el interruptor de llave deI sistema de funcionamiento atr,_s(ROS) en la posici6n "ON" y el embrague del accesorio conectado,cualquier tentativa del operador de viajar marcha atr_s, NO apagar& et motor. Posici6n ROS "ON" CUIDADO Motoren posici6n"ON" (Operaci6nNormal) DE LA CUCHILLA Para obtener los mejores resultados,Iacuchillade lacortadoradec_speddebeestarat_lada. Cambie la cuchilla si est&desgastada, dobladao daSada. _ PRECAMCION: Use s61o una cuchitla de reemplazo aprobada per el fabricante de la cortadora de c_sped. Usar una cuchilla no aprobada peligroso, pues podria daSar la cortadora de c@spedy anular {a garantfa. RETIRe DE LA CUCHILLA per el fabricante de la cortadora de c_sped es 1. Eleve ta cortadora de c_sped a la posici6n m&s alta para tener acceso a Ia cuchilla. NOTA: Prot@jase las manes con guantes yio envuelva la cuchilla con un paso grueso. 2. Retire el perno de la cuchilla gir_ndolo hacia la izquierda. 3. Instale la nueva cuchilta con el disei=Ioque dice "ESTE LADe HACIA ARRIBA" hacia ]a H Eje de rueda/_:_ _----+_ _ SISTEMA PRESENCIAOPERADOR Y SISTEMA FUNCIONAMIENTO ATRAS (ROS) Asegurarse de que el sistema de presencia del operador, el sistema de trabajo y el sistema funcionamiento atr&s funcionen bien. Si tu cortadora de c_sped no funciSn come descrito, reparar el problema inmediatamente. plataforma y et ensamblaje del mandril. orificiocentra_ '_ _"+L-_--_\ _ Lf_ • El motor no arrancar& si el pedal de embrague/ Pee rn°chilla_'_'+ freno est,_ mando deI embrague cornpletamente del accesorio presionado est& descoy el nectado.SISTEMA PRESENCIA OPERADOR VERIFIEZ (especial) __ _ . ___+ +_\ _ " __,. CucMla Mandril Armado Estrelta • Cuando el motor est& en marcha, cualquier tentativa del operador de abandonar el asiento sin haber puesto el freno de estacionamiente primero, apagar,_ el motor, IMPORTANTE: Para asegurar un ensambla|e correcto, el orificio central de la cuchilla se debe alinear con la estre[Ia del ensamblaje deI mandril. • Cuando el motor est,_ en marcha y et embrague del accesorio est& conectado, cualquier ten+ tativa del operador de abandonar el asiento, apagar& el motor, 4+ Instale y ajuste bien el perno de la cuchi]la (45 - 55 pies/Libras). IMPORTANTE: Et perno de Ia cuchilfa especial est& tratado con calor. 48 BATERiA CAMBIO La cortadora de c_sped tiene unsistema de carga de la bater|a que es suficiente para el use normal • Mantenga Ia baterta y los conectores limpios. • $61o recargue la bateria con un cargador aprobado para una bateria de 2.8 amperes hera de 12V. Determine el range detemperaturaesperado antes de cambiar el aceite. Todo el aceite debe cumplir con Ia clasificaci6nSG-SL de serviciode API. • AsegSrese de que lacortadora de c_sped est@ sobre una superficie nivelada. • El aceite se drenar& con m&s libertad euando est@tibio. • Cargarla con cualquier otto cargador o con un cargadortipo automotriz puede causar unda_o permanente en la bateria, • Cargue la batefla durante 24 horas para que se cargue per complete. NOTA: La baterladei equipooriginaJde lacortadora de c_sped no necesita mantenimiento. Nointente abrir ni retirar los tapones o las cubiertas.Agregar o revisar el nivel deI electrolito no es necesario. ADVERTENCIA: No fuerce et arranque de la bateria. Puede ocurrir un da_,opermanente en la bateria o una lesi6n personal. ENFRIAMIENTO DEL TRANSEJE Mantenga el transeje tibre de cualquieracumulaci6n de suciedad y paja, Io que puede restringir et enfdamiento. CINTA EN V Revise la cinta en V para vet siest_ detedorada o desgastada despu@sde 100 horas de operaci6n y c_mbiela si es necesario. La cinta no es ajustable. Cambie la cinta si comienza a deslizarse per el desgaste. MOTOR LUBRICACION Use s61o un aceite detergente de alta calidad calif_cado con la clasificaci6n SG-SL de servicio de API. Seleccione el grade de viscosidad SAE del aceite de acuerdo con la temperatura de operaci6n esperada. NOTA: Auque los aceites de viscosidad m6ltip!e 5W30,10W30, etc.) mejoran etarranque en climas fries, los aceites provocar,_n un incremento en el consume de aceite cuando se usan per encima de los 32°F (0°C), Revise el nivel de aceite del motor con m,_sfrecuencia para evitar cualquier posible daSoen el motor debido a un nivel bajo de ace;te. Cambie el aceite despu@s de cada 25 horas de operaci6n o al menos una vez al aSo si no se va a usar la cortadora de c_sped durante 25 horas en un a_o. Revise el nivel de aceite del c&rter antes de arrancar el motor y despu_s de cada echo (8) horas de operaci6n. Apdete bien el tap6n/la varilla de tlenado del aceite cada vez que revise el nivel deI aceite. DE ACEITE DEL MOTOR ° Recolecte el aceite en un recipiente adecuado. _lh PRECAUCI6N: Si el motor se ha operado durante un tiempo prolongado inmediatarnente antes de drenar el aceite, _ste estar& caliente. 1. Levante la cubierta del motor, 2. Retire e[ tap6n/la varilla de Ilenado del aceite. Tenga cuidado de no permitir que entre suciedad en el motor cuando cambie el aceite. 3, Coloque ef recipiente para recolectarel aceite. 4. Retire el tap6n de drenado y drene el ace_te hacia el recipiente. 5. Despu@sde que el aceite se haya drenado per complete, vueiva a colocar el tap_Snde drenado y apri6telo bien. 6. Rellene el motor con aceite a trav6s de1tube de la varilla de ][enado de aceite. Vi_rtalo despacio. No Io Ilene de m_.s. Para conocer la capacidad aproximada, consulte la secci6n de "ESPECIFICACIONES DEL PRODUCTO" de este manual 7. Use un calibrador en el tap6nivarilla de Uenado de aceite para verificar el nivel. Para tenet una lectura exacta, apriete bien el tap6n de lavariUa sobre el tube antes de retirar la varilia. Mantenga el aceite en la linea que dice "LLENO" en la varifla. Apriete bien el tap6n en el tube cuando termine. 8. Baje la cubierta del motor. Tap6n/variIla de Ilenadode aceite Conector del drenaie de aceite 49 Gubiertadel motor. PUERTO DE LAVADO DE LA CUBIERTA La cubierta de su tractor estA equipada con un puerto de Iavado sobre la superficie que forma parte del sistema de lavado de la cubierta. Se deberla utilizer cadavezque se haya usado elt factor. t. Ueve el tractor a un |ugar horizontal y despejado de su c@sped, 1o bastante oerca de una boca de riego como pare que Hegue la manguera del jardin. IMPORTANTE: Asegt_rese de que Ia boca de descarga del tractor est& orientada LEJOS de su case, garaie, coches aparcados, etc. Quite la boca de ensacadc o cubierta de mantillo si est& acoplada. 2. Mueva elcontrolde! embrague de[accesorio ala posiciSn"DESENGANCHADO", ponga el freno de estacionamiento y apague el motor. 3, Enrosque el adaptador de la boquilla (empaq uetado con el man ualdeI operador del tractor) en el extremo de la manguera del jard{n. 4. Eche hacia atr&s ta abrazadera de cierre del adaptador de la boquilta y empuje _ste en el puerto de lavado de la cubierta en el extremo izquierdo de ta cubierta de la segadora. Suelte la abrazadera de cierre pare fijar el adaptador en la boquilla. Puertode LavadO Manguera Adaptador | de B°qu{I}a_-_ IMPORTANTE: Tire de la manguera para asegurarse de que Ia conexi6n est_ bien fija. 5, Abra la {_avedel agua. 6. Desde la posici6n del operador deI tractor, vuelva aarrancarel motory ponga lapalanca de aceleraci6n en la posici6n "Fast" (r&pido). IMPORTANTE: Vuelva a comprobar la zona pare asegurarse de que estA despejada. 7. Muevael controldelembrague delaccesorio a laposici6n"ENGANCHAR". Mant_ngaseenla posici6n del operador con lacubierl_ de corte acoplada haste que la cubierta est@Iimpia. 8. Muevaelcontrolde]embrague de|acceso_io a laposici6n "DESENGANC HADO".Girelallave de encendido ala posici6nSTOP para apagar el motor del tractor. Cierre la Itave del ague. g. Tire hacia atrAs la abrazadera de cierre deI adaptadorde ia boquilla pare desconectar el adaptadordel puertode lavado delacubiert& !0. Ueve e] tractor a una zone seca, preferentemente de cemento o pavimentada. Mueva el control deI embrague det accesorio a ta posici6n "ENGANCHAR" pare quita_ eI exceso de ague y ayudar a que se seque antes de guardar el tractor. _ADVERTENCIA: Si el accesodo de lavado estd roto o no estd, Ud,y otras personae estardn expuestos e que la hoja les lance aquellos objetos con los que entre en contacto. . Sustituya inmediatemente el accesodo de lavado roto o que falta antes de volver a usar la segadora. - Tape todos los or]ficios de ]a segadora pernos y tuercas de seguridad, FILTRO con DEL AIRE Su motor puede sufrir avedas y funcionar de manera inoorrectacon un filtro de] aire sucio. D61e servicio alfiltro de aire m&s a menudo si se usa en condiciones potvorosas. Vea lamanual de lamotor. LIMPIE LA PANTALLA DE AIRE La pantatta de aire se debe rnantener fibre de suciedad y paja para evitar que el motor se daSe por sobrecalentamiento. Limpie con un cepilIo de alambre o conaire comprim[do para retirarta suciedad y Iasfibras de goma secas dificiles de quitar. LIMPIE LAS AREAS DE ENTRADA DE AIRE!ENFRIAMIENTO Pare asegurar un enfriamiento adecuado, cerci6rese de que la pantalla de c6sped, las aletas de enfriamiento y otras superficies externas de] motor se mantengan limpias en todo momento. Cada 100 horas de operacibn (con m&s frecuencia bajo condiciones de po]vo y sueiedad extremas), retire la carcasa del soplador y otras cubiertas de enfriamiento. Lirnpie las aletas de enfriamiento y Ias superficies externas conforme sea necesario. Aseg_rese de reinstalar de nuevo las cubiertas de enfriamiento. NOTA: La operaci6n del motor con la pantalla de c_sped bloqueada, las aletas de enfriamiento sucias o taponadas y/o las cubiertas de enfTiamiento sin colocar causar&dafio pot sobrecalentamiento. 5O LIMPIEZA FRICCION DE SUPERFICIES DE Para asegurar un desempe_o de manejo apropiado, mantenga las superficies de friccibn libres de suciedad, residuos y exceso de goma en todo momento. Cada 25 horas de operaciSn, es necesario limpiar las superficies de fficci6n frot&ndolas con alcohol isopropilo u otro limpiador sin pelicula. Placa del motor Disco de fricci6n SILENCIADOR Inspeccione y cambie el silenciador y et parachispas sitienen corrosi6n (si fa unidadest& equipada con _stos) porque se podria generar un peligro de incendio y/o daSos. BUJJA(S) Cambie [a(s) bujia(s) al principio de cada temporada o despu_s de cada 100 horas de operaci6n, Io que ocurra primero. El tipo de bujfa y la configuraciSn del espacio se muestran en la secci6n "ESPEQIFtCACIONES DEL PRODUCTO" de este manual. LIMPIEZA • Umpie cuaiquier materia extrafia del motor, Ia baterfa, el asiento, el acabado, etc, • Mantenga Ias superficies con acabado y tas Ilantas libres de cualquier residuo de gasolina, aceite, etc. • Proteja Ias superficies pintadas con cem tipo automotriz. No se reoomienda usar una manguera para jardln ni una lavadora a presi6n para limpiar la cortadora de c_sped, a menos que el motor y la transmisiSn est_n cubiertos para protegerlos deI agua. Si entra agua en el motor o la transmisiSn se reducir& la vida 5til de Ia cortadora de c_sped. Use aire comprimido o un soplador de hojas para retirar el c_sped, las hojas y la basura de la cortadora de c_sped. 51 I_ CUALQUIER DVERTENCIA: PARA EVITAR SERVICIO O AJUSTE: UNA LESION SERIA, ANTES DE HACER I, Suelte por completo elpedalde embraguetfreno yaccione el frenode estacionamiento. 2. Coloque Ia palanca de control de movimiento en la posici6n neutral (N), 3. Coloque el embrague de la plataforma en la posici6n "DESACTIVADO", 4. Gire la Ilave de arranque a la posici6n "PARAD,_' y saque la llave. 5. AsegSresedequelacuchillaytodaslaspartesm6vilessehayandetenidoporcompleto. 6. Desconecte el cable de ta bujia de 6sta 5Itima y coloque eI cable donde no pueda entrar en contacto con la bujia. CORTADORA DE ClaSPED RETIRO DE LA CORTADORA 6. DE CteSPED Retire el pasador que sostiene en su lugar el brazo del esfab6n del elevador de la plataforma. 1. Coloque el embrague de la plataforma en la posici6n "DESACTIVADO", 2. Mueva la palanca dee elevador de ajuste de altura de Ia cortadora de c6sped hacia adelante para bajar Ia cortadora de c6sped a su posici6n m_,s baja, Retire la cubierta de] mandril, 8. Retire la cinta del rededor de las poleas. 9, Deslice la plataforma hacia afuera desde el fado inferior de la cortadora de c_sped. Retire los pasadores quesostienen en su lugar tos brazos de suspensi6n frontales izquierdo y derecho de la cortadora de c_sped. Retire el pemo que sostiene en su Iugar la varilla de nivelaci6n deI frente a Ia parte posterior de la plataforma. INSTALAClON DE LA CORTADORA DE ClaSPED Instale en reve rsa de acue rdo con las instrucciones de lasecci6n "RETIRO DE LA CORTADORA DE ClaSPED". 3. 4. 5. 7, Retire eI perno que sostiene en su lugar la varilla de nivelaci6n de lado a lado de la plataforma. Perno de varilIa de lado a lado nivelador de la Perno de varilla de nivelaci6n frontal eslab6n dei elevador de Ia plataforma Pasadordelbrazo desuspensi6n de la corta_orade c_sped 52 NIVELACION CORTADORA DE LA CARCASA DE CESPED AJUSTE DEL FRENTE A LA PARTE POSTERIOR DE LA IMPORTANTE: La plataforma debe estar nivelada de lado a [ado. Ajuste la cortadora de c_sped mientras est_ estacionada en et suelo o en un camino nivelado. Aseg_rese de que tas Ilantas est6n bien infladas (Observe la parte lateral de la [lanta para verificar que la PSI sea correcta). Si [as Ilantas est&n infladas de m&s o de menos, usted no podr& ajustar bien la cortadora de c_sped. AJUSTE DE LADO A LADO Para obtener los mejores resultados de corte, Ia carcasa de la cortadora de c6sped se debe ajustar de modo que el #ente est_ aproximadamente de 1/8" a I/2" m&s abajo que la parte posterior cuando la cortadora de c_sped est,' en su posici6n m&s alta. Revise el ajuste del lado derecho de la cortadora de c_sped. Mida la distancia"F" directamente en #ente y detr&s del mandril en la orilla inferior de la carcasa de la cortadora de c6sped conforme se muestra. • Eleve la cortadora de c_sped a su posici6n m&s alta. • Mida ]a distancia "A" desde la orilla inferior de la cortadora de c_sped al nive] del suelo en ]as esquinas frontales de la cortadora de c6sped. Ori]la inferior de la cortadora de c_sped en relaci6n con el suelo ii Ori[la inferior de la cortadora de c6sped en relaci6n con el suelo (j fA • Para elevar el lado derecho de la cortadora de c_sped, apriete latuerca de ajuste de1eslab6n del elevador. • Para bajar el lado derecho de la cortadora de c_sped, afloje la tuerca de ajuste del eslabSn del elevador, NOTA: Carla vuelta completa de la tuerca de ajuste cambiar& laaltura de lacortadorade c_sped aproximadamente 8/16'L • Vuelvaa revisar las medidas despu_s de] ajuste. NOTA: Cada vuelta completa de '=G"cambiar& "F" aproximadamente 3/8", • Vuelva a revisar el ajuste de lado a lado. Tuerca Haga g,tar i_'_"'_>.__ " tuercahacia / _/_. \ la derecha / i\-._ \.\ _ parasubirla _ _.._\ _ _ segad_d_L_.....__ k._ • Para bajarelfrente de lacarcasa de lacortadora de c_sped gire Ias tuercas "G" y "H" hacia la derecha. • Cuando ladistancia"F" est6 de 1/8"a 1/2" m_s abajo en el frente queen la parte posterior, apdete la tuerca "H" contra el mufi6n en el eslab6n frontal. • Para elevar el frente de Ia carcasa de la cortadora de c6sped gire las tuercas "G" y "H" hacia la izquierda. • Cuando ]a distancia "F" est6 de 1/8"a 1/2" m&s abajo en el frente queen Ia parte posterior, apriete la tuerca "H" contra el mufi6n en el eslab6n frontal. )/ Hagagi_aarcli_ tuerca ' [aizquierda parabajarla sega,ora 53 CAMBIO DE CINTA DEL IMPULSOR LA CUCHILLA DE LA CORTADORA ClaSPED RETIRO DE CINTA DEL IMPULSOR CORTADORA DE CESPED 1. 2. 3, 4, DE DE DE LA Estacione la cortadora de c@spedsobre una superficie nivetada. Accione el freno de estacionamiento, Baje Ia cortadora de c_sped a su posici6n m_.s baja, Retire la cubierta del mandril desde la plataforma de ta cortadora de c6sped. 5, 6. Retire Ia placa det motor posteriorde ta unidad. Retire la sujeci6n de ta cinta posterior de la unidad. 7, Enrolle con cuidado Ia cinta sobre la parte superior deI mandril de Ia cuchilla de la cortadora de c@sped. Cinta de impulsor de Ia cortadora de c@sped Sujeci6n \ de cinta 2, Coloque la palanca de control de movimiento en la posici6n neutral. Las ruedas traseras deben bloquearse y patinar cuando se intente empujar manualmente la cortadora de c@spedhacia adelante. Si ]as ruedas traseras giran, se debe dar mantenimiento aI freno. Comuniquese con un centro de servicios Sears u otro centro de servicios autorizado. AJUSTE DE LA ALINEACION VOLANTE DEL Si los travesa5os del volante no estdn en posici6n horizontal (de izquierda a derecha) cuando Ias ruedas est4n en posici6nrecta hacia adelante, retire el volante y reens&mblelo de acuerdo con las instruccionesde la secci6n "INSTALACION DE LACOLUMNA DE DIRECCION" de este manual. CAMBIO DE RUEDA PARA REPARACION RUEDA FRONTAL I. 2. Bloquee bien el eje frontal, Retire la cubierta para polvo, el anillo de retenci6n y Ia arandela para poder retirar la rueda. 3. 4, Repare la tlanta y vuelva a ensamblarla, Vuelva a colocar bien Ia arandela y el anillo de retencion en la ranura de] eje. RUEDA POSTERIOR t, Bloquee bien el eje posterior. 2. Retire Ia cubierta para polvo, el anilto de retenci6n, la arandela y la llave cuadrada mientras jala la Ilanta hacia afuera. 3, Repare Ia tlanta y vuelva a ensamblarla, 4, Vuelva a colocar la Ilave cuadrada mientras coloca de nuevo ]a Ilanta y despu6s vuelva a colocar bien la arandela y el anillo de retenci6n en ]a ranura del eje. Poleas guia Mandril 8, 9, Retire Ia cinta de las poleas guia. Revise Ias poleas guia paraverque giren con Iibertad, 10. Retire lacintade lapo]eadel impulsorposterior, INSTALACION DE CINTA DEL IMPULSOR DE LA CORTADORA DE CESPED Instale en reversa de acuerdo con las instrucciones de ta secci6n "RETtRO DE LA CINTA DEL IMPULSOR DE LA CORTADORA DE CESPED", Arandela retenedor Anillo VERIFICACION ! DEL FRENO Si la cortadora de c@spedrequiere m_.sde cuatro (4) pies (1,219 metros) para detenerse a la velocidad m_ima sobre una superficie de concreto o pavimento seco nivelado, entonces se debe dar servicio al freno. Tambi4n se puede vedficar el freno mediante las siguientes acciones: 1. Estacione la cortadora de cesped sobre una superficie de concreto o pavimento seco nivefade, presione el pedal del embrague/freno pot completo y apfique et freno de estacionamiento. \\_ Cubierta de polvo Llave cuadrada (s6Io en [a rueda posterior) NOTA: Para seltar las pinchaduras de las Ilantas y evitar que _stas se desinflen debido alas fugas tentas, compre y use sellador para Ilantas. El selfadorde Ilantas tambi@npreviene Ia podredura en seco y la corrosi6n de las llantas. 54 ARRANQUE DEL MOTOR BATERiA DESCARGADA CON UNA 6. Renistale la abrazadera y el pemo de Ia bated& _IIPRECAUCI6N: [_as bateria_s de plomo &cido generan gases e×plosivos. Mantenga los matedales que producen chispas,llamas y humo lejosde las baterias. Use siempre una protecci6n para los ojoscuando est_ cerca de las baterlas. Si su baterla est_ demasiado baja como para arrancar el motos, _sta se debe recargar. (Consuite Ia parte de "BATERIA? en ]a secci6n de Mantenimiento de este manual). Esta unidad est_ equipada con un sistema de arranque manual del motor que se puede usar si Is baterfa est& demasiado descargada corno para arrancado. Consulte la parte de "SISTEMA DE ARRANQUE MANUAL_ en la secci6n de Operac]6n de este manual. CAMBIO DE LA BATERiA ADVERTENCIA: Noproduzcauncortoenlas terminales de la bateria al permitir que una Ilave ingiesa o cuaiquier otro objeto entre en contacto con ambas termina[es aI mismo tiempo. Antes de conectar la baterfa, retfrese cuatquier brazalete de metal, pulsera de reloj, anillos, etc. La terminal positiva se debe conectar primero para evitar que se produzcan chispas pot hacer tierra en forma accidental. 7. Conecte primero el cable ROJO de la bateda en Ia terminal pos_va (+) de ta bateda, 8. Conecte el cable de la tierra NEGRO en Ia terminal negativa (-) de la bated& DISPOSITWOS RELI_S DE SEGURIDAD Y El cableado suelto o da_ado puede causar que la cortadora de c6sped funcione real, deje de avanzar o no arranque. Revise e[ cableado. Aseg_rese de que todo el cableado y los conectores est_n bien colocados. MOTOR La velocidad del motor se ha configurado en la f_brica, No intente incrementar la velocidad del motor porque puede sufrir una lesi6n personal, Si usted cree que el motor estd funcionando demasiado r&pido o demasiado lento, Ileve su cortadora de c6sped a un cantro de servicios Sears u otro centrode serviciosautodzado para su reparaci6n yio ajuste. 1. Levante el asiento para tener acceso al perno. 2, Desconecte el cable NEGRO de la bateria y luego el cable ROJO de la bater_a. 3, Desconecte el cab[e NEGRO de la bater[a, despu_s el cable ROJO de ia baterla, la correa de la baterla y retire con cuidado la bateda de la cortadora de c_sped. 4. Retire el perno de Ia abrazadera de Ia bateria, 5. lnstale la nueva baterfa con las terminales hacia la derecha y lejos del asiento conforme se muestra. DelAsiento_ Perno 55 Prepare de inmediato su cortadora de e@sped para almacenarla al final de ia temporada o si no Io va a utilizar durante 30 alias o m&s. • Nunca use productos limpiadores para motor o carburador en eltanque decombustibleporque puede ocurrir un dafio permanente. A ADVERTENCIA: Nunca almacene la cortadora de c_sped con gaso]ina en el tanque adentro de un edificio deride los humos puedan alcanzar una flama abierta o una chispa. Permita qua el motor seenfrie antes de almacenarla en cualquier lugar cerrado, • Use combustible nuevo en la pr6xima temporada. CORTADORA DE CF-SPEB Retire Ia plataforma de fa cortadora de c@sped para su almacenamiento durante el invierno. Cuando vaya a almacenar la cortadora de c#sped durante un tiempo, Iimpiela a conciencia, retire toda la sicuedad, grasa, hojas, etc. Almac@nela en un _rea limpia y seca. 1. Limpie toda la cortadora de c6sped (consulte la parte de "LIMPIEZ_' en Ia secci6n de Mantenimiento de este manual). 2. ]nspecione y cambie la cinta,, si es necesario (consulte ta parte de instrucciones de cambio en Ia secci6n de Servicio y Ajustes de este manual). 3. Lubrique conforme se indica en ]a secci6n de Mantenimiento de este manual. 4. Asegerese de que todas ias tuercas, pemos ytorniltosest@n bien apretados. Inspeccione las partes m6viles en busca de algt_n dafio, roturay desgaste. Cdmbielas sies necosario. 5. Retoque todas las superficies de pintura oxidadas o desposti!ladas. Iije un poco antes de pintar. ACEITE DEL MOTOR Drene el aceite (con el motor tibio) y c_.mbielo per aceite de motor timpio, (Consulte la parte de "MOTOR" en la seoci6n de Mantenimiento de este manual). CILINDRO(S) 1. Retire la(s) bujia(s). 2. Vierta unaonza de aceite per el(los) orificio(s) de la(s) bujia(s) hacia el(los) cilindro(s). 3. Gire la !lave del arranque a la posici6n de '_RRANQUE" durante unos cuantos segundos para distribuir eI aceite. 4. Coloque Ia(s) bujia(s) nueva(s). OTROS • No almacene la gasolina de una estaci6n a otra. BATERiA • Cargue per complete la bateria antes de almacenar. • Si la bateda se retira de Ia cortadora de c_spad para atmacenada0 no a[macene la baterla directamente sobre superficies de concrete o hL_medas. MOTOR SISTEMA NOTA: El estabilizador de combustible es una alternativa aceptable para minimizar la formaci6n de dep6sitos de goma de combustible durante el almacenamiento, Agregue estabilizador a la gasolina en el tanque de combustible o recipiente de almacenamiento. Siga siempre la proporci6n de mezcla que se encuentra en el recipiente del estabilizador. Deje funcionar el motor al menos durante 10 minutes despu_s de agregar el estabilizador para permitir qua e[ estabilizador llegue al carburador. No vacie el tanque de gasotina y el carburadorsi utilizaestabilizador de combustible. DE COMBUSTIBLE IMPORTANTE: Es importante evitar que se formen dep6sitos de goma en las partes esenciales deI sistema de combustible come el carburader, la manguera de combustible o el tanque durante el almacenamiento. Asimismo, los combustibles mezclados con alcohol (llamados gasoboI o que usan etanol o metanol) pueden atraer la humedad, Io que provoca la separaci6n y formaci6n de Acidos durante el almacenamiento. El gas Acido puede daSar el sistema de combustible de un motor mientras se encuentra en almacenamiento, • Vacie el tanque de combustible al arrancar el motor y dejarlo funcionar hasta que Ias lineas de combustible y e[ carburador est@nvaci'os. 56 • Cambie Ia Iata de Jagasolina si comienza a oxidarse. El 6xido y/o la suciedad en ]agasolina causar& problemas. • Si es posible, almacene lacortadorade c#sped en intedores y c5brala para protegerla deI polvo y Ia suciedad. • Cubra la cortadora de c@sped con una cubierta protectora adecuada que no retenga la humedad, No use pl_.stico. El pldstico no puede respirar, Io que permite qua se forme condensaci6n y causarA que la cortadora de c6sped se oxide. tMPORTANTE: Nunca cubra la cortadera de c@sped mientras el me tory las Areas de escape todav[a est_n calientes. IDENTIFICACION DE PROBLEMAS: Veala secci6napropiadaen elmanuala menos queest_ dirigidoa uncentrede servicioSears. CAUSA PROBLEMA No arranca Dificultad arragcar para CORRECCION t No tiene combustible, 1 Llene e] tanque de combustible, 2 3 4 Buj_a defectuosa, Filtro de aim sucio. Ague en el combustible. 2 3 4 5 6 Cableado suelto 0 dafiado. I_as v&Ivulas del motor estdn desajustadas. Cambie Ia bujia, Limpie/cambie el filtro de airs, Vacie e] tanque de combustible y el carburador, rellene el tanque con gasolina nueva y cambie et filtro de combustible. Revise todo el cableado. Contacte a un centre de servicios Sears u otto centre de servicios autorizado. 1 Filtro de airs sucio. 2 3 4 Bujia defectuosa. Bateda baja o muerta. Combustible viejo o sucio. 5 6 Cableado suelto o daSado. Las v_,lvutas del motor est&a desajustadas, Limpieicambie el fi3tro de airs, 2 3 4 Cambie ]a bujfa. Recargue o cambie Ia bateria, Vacie el tanque de combustible y rell6nelo con gasolina nueva y limpia. 5 Revise rode el cableado, 6 Contacts a un centre de seP_icios Sears u otro centre de servicios autodzado, ,, ,,,,,, El motor no da vueltas 1 2 13 4 5 6 7 8 g LEI motor i ohasquea pero no arranca P_rdida energia de Presione el pedal deI emgrague,ffren0. 2 3 4 5 6 7 8 9 Desacfive el embrague de Ia )Iataforma. Recargue o cambie la batefia. Cambie el fusible. Limpie lasterminales de la baterfa, :_evisetodo el cableado. Revise/cambie elinterrupterde arranque. Revise/cambie el solenoide o arranque, Contacts a un centre de servicios Sears u otto centre de ssrVicIos autodzado. ,,,, ,,,,, .... 1 2 Baterfa baja o muerta, Termina]es de bater[a con corrosi6n. 1 Recargue 0 cambie la bateria. 2 Limpie las terminales de la bateda. 3 Cableado suelte o daP,ado. 3 Revise Jodo el cableado. 4 Solenoids o arranque defectuoso. 4 Reviseicambie el solenoide o arranqu e, 1 Corte de demasiado c_sped/demasiado r&pido, Acumulaci6n de c_sped, he[as y basura debate de la cortadora de cesped. 1 Eleve la altura de corteireduzea la velocidad. Limpie ta parte inferior de ]a carcasa de la corladora de c_sped, 2 Vibraci6n excesiva El franc Gel embragueifmno no estd )resionado, El embrague de ]a plataforma est& act_¢ado, Bateria baja o muerta, Fusible fundido. i Terminales de bateria con corrosi6n, Cab[eado suelto o dafiado. interrupter de arranque defectuoso, Solenoids o arranque defectuoso. Interrupter(as) de presenctade eperador defectuoso(s): ......... 2 i 3 i Limpie/cambie el filtro de airs. i 4 _Revise et hive] de aceite/cambie el ' Iaceite, 5 Limpie y ajuste o cambie ia bujfa. 3 4 Filtro de airs sucio. N_veI bate de acei|e/ace_te sucio, 5 Bujia defectuosa. 6 Combustible viejo o sucio, 6 Vaeie el tanque de combustible y rell_nelo con gasoline nueva y limpia. 7 Ague en el combustible, 7 8 9 10 11 12 Cable de fa bujfa suelto, Pantalla/aletas de airs deI motor sucias. Silenciador sucio/obstruido, Cab_eado suelto 0 daflado. I_asv&ivulas dst motor est&n desajustadas. 8 Vacie el tanque de combustible y e[ carburador y rellene el tanque con gasoline nueva. Conecte y ajusta el cable de la bujia. 1 Cuchil[a desgastada, dobiada o suelta, 2 Mandril de cuchilla doblado. 3 Parle(s) sueita(s)/daSada(s), 9 Limpie la pantafla/aletasd eaire deI motor, 10 Limpie/cambie el silenciador. 11 Revise todo ef cableado. 12 Conlacte a un centre de servicios Sears u otto centre de servicios autodzado. 1 Cambie la cuchilla. Apriete el pemo de la cuchilla. 2 Contacte eun centre de servicies Sears u otto centre de serv[cios autorizado. 3 Apriete la(s) parts(s) suelta(s)/ dafiada(s), Cambie tee partes da_adas, ,, ,,,, 57 IDENTIFICACI6N Vea la secci6n DE PROBLEMAS: apropiada PROBLEMA en el manual a menos que est_ dirigido a un centre CAUSA de servicio El motet sigue funcionando cuando el operador deja el asiento con elembrague activado 1 Sistema de control de presencia de seguridad deI operador defectuoso, Carte deficients - carte no uniforme 1 CuchilIa desgastada, doblada o suelta, t Revfse el cableado_ los interroptores y las conexiones. Si no son correctos, contacts a un centre de servicios Sears u otro centre de servicios autorizado. ..... La cuchitla de la cortadora de c_sped no gira Descarga de c_sped deficiente ,,,,,,, Plataferma de cortadora de c_sped no nivelada, 3 AcumulaciSn de c_sped, he as y basura debajo de a cortadora de cesped, 4 Mandril de cuchilla doblade. Respiradero de ra cortadora de c6sped obstruido per la acumulaci6n de c_sped, hojas y basura alrededor del mandril. 1 Obstrucci6n en el mecanismo del embragua. 2 Cinta de] impulsor de ta cortadora de cesped desgastada/daSada, ;3 Paisa de gu{a congeiada. t 4 Mandril de cuchille congelado. 4 Contacts a un centre de servicios Sears u otro centre de serv{cios autorizado. Gamble a una velocidad m&s Ienta. 1 Valocidad de avance demasiado r_pida. 1 C_sped h6medo. 2 3 PJataformade cortadora de c_sped no niveJada. Presi6n de airs de ias Ilantas baja/no uniforme, Cuchi[la desgastada, dobJada o suelta. 3 5 6 7 8 Acumulaci6n de c_sped, hoias y basura debajo de la eortadora de cesped, Cinta de impu[sorde la cortadora de c6sped desgastada, Cuchilla real instalada. ' 9 :Use inapropiado de cuchille, no carga 1 4 5 6 7 8 9 10 Orificios del respiradero de la codadora de c_sped abstruidos par Ia acumulaci6n de c6sped, hojas y basura alrededor de los manddles. Celda(s) de bateria defectuosa(s), :_ Conexiones de sabre defectuosas. 3 Alternador defectuoso. 10 t de 1 Permita que el c_sped se seque antes de podarlo. , Nivele la plataforma de ]a cortadora de I c_sped Revise que la PSI de las iJantas sea adecuada. Cambie/afile la cuchilla. Apriete el perno de acuch a Limpie la parte inferior de la c_rcasa de la cortadora de c#_sped. Gamble Ia cinta de] impulsor de la cortadora de c_sped, Reinstale la odlla f/lose de la cuchilla hacia aba_o. Cambie per una cuchi]la de la Iista de este manual, Limpie alrededor de los manddles para abrir los oriticios deJ respiradero. Cambie la bater{a. 2. Reviseilimpie 1odes las cone×iones. :3 Cambie el alternador. ..... ,,, P_rdida impulse Retire _aebstrucciSn. 2 Cambio la cinta del impuTsor de Ia cortadora de e_sped, 3 Cambie la paisa de gufa. 2 4 La bater{a 1 Cambie la cachilla, Apriete e] perno de la cuchilla. 2 N_vele la pletaforma de Ia coHadora de c_sped. 3 Limpie ia parts inferior de la carcasa de la cortadom de c_sped. 4 Contacte a un centre de servicios Sears u otro centre de servicios autorizado. 5 Limpie alrededor do los mandriles pare abrir Josorificios del respiradero. 2 5 Sears. CORRECCION ,,,, Falta la Ilave de] eje. t , instals la Ilave deI eje en la rueda po_terior_Consulte la parts de "COMe RETJRAR LA RUEDP_'en la secciSn de Servicio y Ajustes. El motor se muere ouando la cortadora de 1 El sistema de funcionamiento atria (ROS) no est& "ON", cuando enganche ;a segadora o otro accesorio. 1 Girar e] ROS an [a pesici6n "ON".Vea la secciSn de operaci6n. c_sped se cambia ala posici6n de reverse, 2 2 El motor est,. fr{o. 58 Permita que el motor se salients dejbn:tale funcionar de varies segundos a varies minutes. GU{ASUGERIDAPARA MEDIR LAS PENDIENTESCON LA VISTA PARAUNA OPERAClONSEGURA O3 _O ! _b y abajo de _as Pend[entes, nunca transversa]mente con respecto alas I ADVERTENCIA: Para evltar da_os msyores graves, hags su tractor arriba I pendlentes. No cotter pend[entes de 15funsionar grados. Hags los vlrajes gmdualmente para evitar volcarse o le p_rdfda de control. I Tenga mucho cuidado ¢uando cambie de direcci6n en las pend]entes. 1. P{egar eeta pdglna a ]o largo de la Ifnea punteada arriba fndlcada. 2. Tenet la pdglna ante de si mJsmos de modo que su borde Izquierdo sea vertical peralelo a! tronco del _;rbol u otra estructura vertical. 3. Miter a tray,s de! p,egue en direcci6n de la pendiente que se quiere medir. 4. Comparar el =ingulo del pgegue con ]a pendlente del terteno. I NEED MORE HELP.:' i YoU|t find the answer and more on raaaagemyhome.cora - for free! i • Find this anda[[yourother product manuals onSne, • Getanswers fromourteamofhomeexperts. _ i •Geta persona|ized maintenance ptanforyourhome. - Find information andtooL_ tohelp _th homeprojects. _?i _i manage t_'_ home Your Home For repair - in your home - of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold itl For the replacement parts, accessories and owner's manuals that you need to do-it-yourself. For Sears professional installation of home appliances and items like garage door openers and ,water heaters. 1-800-4-MY-HOME ® (1-800-469-4663) Anytime, dayornight (U,S,A, and Canada) www,seaP3.com WWW,Se_ra,_a Our Home For repair of carry-in products like vacuums, lawn equipment, and electronics, call or go on-line for the nearest Sears Parts and Repair Center, %800-488-1222 Anytime. day or night (U,S.A. only) vavw,sears, com _ To purchase a protection agreement (U.SA.) _?L!_ or maintenance agreement (Canada) on a product serviced by Sears: !-800-827-6655 _ _ =_ _ (U.S.A.) 1-800-361-6665 (Canada) Pare pedir serviciode reparaci6n a domidlio, y para on_enarpiezas: 1.888.SU.HOGAR® Au Canada pour service en francis: 1-800-LI=.FOYER_c (1=988-784-6427) ©Se_rs Brands, LL_ ® Regisfered Trademark / TM Trademart_ I SMSsrv_¢e Mark of Seers Brands, LLC ® Mama Registmda t TM Marca de F&btica / _ Ma_'cade Se_vic_ode Sears Stands, LLC _c Marque de commsme / =o Marque d6pos_e de Seers Brands, LLC 03.14.11 TH Printed in the U.S.A.