Download Vestax PCV-150 Owner`s manual
Transcript
Professional Mixing Controller OWNER'S MANUAL VESTAX CORPORATION 1-18-6 Wakabayashi, Setagaya-ku, Tokyo 154-0023 Japan Phone:03-3412-7011 Fax: 03-3412-7013 Web:www.vestax.jp VESTAX America (west Corst) 15320 Valley View Rord Unit 9 La Mirada, CA 90638 Phone:(562)623-9881 Fax:(562)483-7304 Web:www.vestaxdj.com VESTAX (Europe)Ltd. Unit 5 Riverwey Industrial Park Alton, Hampshire GU34 2QL England, U.K Phone:(0)1420-83000 Fax: (0)1420-80040 Web:www.vestax.co.uk Vestax Technical Center of America 8489 W.Third Street Ste.1044 Los Angeles CA 90048 Phone:1-323-801-2111 Fax:1-323-801-2112 Vestax Europe Technical Support Rheinstr.213 D-53332 Bornheim Germany Phone:49(0)2222-95-23-72 Fax:49(0)2222-95-23-74 CONGRATULATIONS! The PCV-150 is a high profile mixer designed to meet various professional requirements of today's dance music DJs. Please read this owner's manual carefully before you start to use your mixer, so that you will fully understand all of the special features and enjoy the full use of the product. CONTENTS C A U T I O N IMPORTANT SAFEGUARDS F E AT U R E S FUNCTIONS FRONT PANEL R E A R PA N E L HOW TO CHANGE THE FADERUNIT CONNECTIONS SPECIFICATIONS 1 2 3 4 5 7 8 9 10 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTl0N:TO REDUCE THE RlSK OF ELECTRlC SHOCK DO NOT REMOVE COVER(OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVlCING T0 QUALIFIED SERVlCE PERSONNEL The lightning flash with arrowhead symbol,within an equilateral triangle,is intended to alert the user to the presence of uninsulated“dangerous voltage”within the product's enclosure that may be of sufficient magnitude to consitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance(servicing)instructions in the literature accompanying the appliance. T0 REDUCE THE RISK 0F FIRE 0R ELECTRlC SHOCK,DO NOT EXPOSE THIS APPLIANCE T0 RAIN 0R M0ISTURE. 1 IMPORTANT SAFEGUARDS READ BEFORE OPERATING EQUIPMENT P This product was designed and manufactured to meet strict quality and safety standards. There are, however, some installation and operation precautions which you should be particularly aware of. 5 V 1. Read instructions-All the safety and operating instructions should be read before the appliance is operated. 2. Retain instructions-The safety and operating instructions should be retained for future reference. 3. Heed Warnings-All warnings on the appliance and in the operating instructions should be adhered to. 4. Follow Instructions-All operating and use instructions should be followed. 5. Cleaning-Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 6. Attachments-Do not use attachments not recommended by the product manufacturer as they may cause hazards. 7. Water and Moisture-Do not use this product near water-for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like. 8. Accessories-Do not place this product on an unstable cart, stand, tripod, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the appliance. Use only with a cart,. stand, tripod, bracket, or table recommended by the manufacturer, or sold with product. Any mounting of the appliance should follow the manufacturer's instructions, and should use a mounting accessory recommended by the manufacturer. 9. This product should never be placed near or over a radiator or heat register. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to. 10. Power sources-This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. 11. Lightning-For added protection of this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet. This will prevent damage to the product due to lightning and power-line surges. 12. Overloading-Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock. 13. Object and Liquid Entry-Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. 14. Servicing-Do not attempt to service product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified personnel. 2 16. Replacement Parts-When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original parts. Unauthorized substitutions may result in fire, electric shock or other hazards. 17. Safety Check-Upon completion of any service or repairs to product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. 18. Carts and Stands-The appliance should be used only with a cart stand that is recommended by manufacturer. 19. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn. 15. Damage Requiring Service-Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. When the power-supply cord or plug is damaged. b. If liquid has been spilled or objects have fallen into the product. c. If the product has been exposed to rain or water. d. If the product dose not operate normally by following the operating instructions. Adjust only those controls that are coverd by the operating instructions as an improper adjustment of other, controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation. e. If the product has been dropped or cabinet has been damaged. f. When the product exhibits a distinct change in performance this indicates need for service. FEATURES ● ● Stereo XLR balanced output with -10/0/+4dB l ev e l s e l e c t s w i t c h e n s u r e s t h e b e s t connection in professional application. Stereo 1/4" unbalanced master output, submaster output and cue output (mono) are also provided for various different occasions. A lot of inputs, 3phono, 5line and 3mic are provided. It makes the PCV-150 into a control center. ● The AC/AC adapter supplies higher current and voltage, which enables the PCV-150 to achieve more dynamic range and better sound quality. ● The cross fader assign switch is newly designed for quick assignment. ● Transformer button is provided for transformer scratch. 3 ● Split/master cue system (selected by switch) meets the different monitoring situation. ● 12segment LED level meter is provided for careful level check. ● A powerful 3band EQ with +6/-24dB range. More sensive and drastic control can be achieved for Techno/Trans mixing. ● The new PCV-150 features removable flat panel that covers screws etc., that will impede fast mixing. The panel is removed for crossfader replacement. ● New superior grade crossfader (CF-PCV) fittde to PCV-150 enabling super smooth operation together with long life. 4 -24dB -24dB MIN +6dB +6dB MAX MAX MAX PHONES MIN OFF MAX SPLIT CUE PHONES LEVEL ON MONITOR TALK OVER LO HI EQ MIC 3 MIN MIC 2 MIN MIC 1 MIC 10 9 8 7 6 5 4 3 2 1 0 LEVEL -24dB CUE LO -24dB MID +6dB +6dB 10 9 8 7 6 5 4 3 2 1 0 LEVEL -24dB CUE LO -24dB MID -24dB HI MIN GAIN HI -24dB PGM 2 PHONO 2 EQ +6dB MAX LINE 1 +6dB +6dB +6dB MAX LINE 2 10 9 8 7 6 5 4 3 2 1 0 LEVEL -24dB -24dB CUE LO MIN -24dB MID HI EQ GAIN LINE 3 PGM 3 +6dB +6dB +6dB MAX PHONO 3 PROGRAM INPUT SECTION EQ MIN GAIN PHONO 1 PGM 1 MIC INPUT SECTION MONITOR SECTION PGM 4 10 9 8 7 6 5 4 3 2 1 0 LEVEL -24dB -24dB CUE LO MIN -24dB MID HI EQ GAIN LINE 4 +6dB +6dB +6dB MAX LINE 5 MIN -20 TRANSFORMER PGM 1 PGM 2 CF ASSIGN CROSS FADER SUB MASTER OUTPUT MASTER LEVEL -10 -8 MIN CUE OUT -12 MAX -16 PCV-150 / PROFESSIONAL MIXING CONTROLLER FOR THE CREATIVE DJ / PRODUCER ALLOWS YOU TO CREATE YOUR OWN MUSIC WITH VESTAX’S UNSURPASSED ENGINEERING AND DESIGN. -4 -2 +2 +4 MAX +8 L MIN MASTER OUT BALANCE 0 MASTER SECTION R PGM 3 PGM 4 MASTER CUE TRANSFORMER CF ASSIGN MAX +12 dB 150 FUNCTIONS 9 FRONT PANEL 8 PGM 1 MIC MIC 1 PHONO 1 MIN GAIN MAX PGM 3 PGM 2 LINE 1 PHONO 2 LINE 2 GAIN LINE 3 PGM 4 PHONO 3 GAIN LINE 4 GAIN MIC 2 1 MIN MIN 2 3 MIN MAX EQ EQ EQ HI HI HI HI +6dB -24dB +6dB -24dB +6dB -24dB MAX EQ MID HI -24dB +6dB -24dB +6dB LO MID -24dB +6dB -24dB +6dB LO 4 TALK OVER 5 ON SPLIT CUE 6 MAX PHONES 7 11 qMIC INPUT LEVEL This knob is used to adjust the input of each mic connected to mic jack on the rear panel. wMIC EQ-HI(Equalizer High) Boosts of +6dB and cuts of -24dB are possible above 10kHz. eMIC EQ-LOW(Equalizer Low) Boosts of +6dB and cuts of -24dB are possible below 100Hz. +6dB -24dB +6dB -24dB +6dB -24dB +6dB CUE -24dB CUE LEVEL 10 9 8 7 6 5 4 3 2 1 0 13 -24dB LO LEVEL 10 9 8 7 6 5 4 3 2 1 0 MID LO LEVEL PHONES LEVEL MIN -24dB CUE CUE OFF MID LO MONITOR rTALK OVER SWITCH MIN MAX EQ -24dB MIN MIN MAX MAX MIC 3 10 9 8 7 6 5 4 3 2 1 0 LEVEL 10 9 8 7 6 5 4 3 2 1 0 14 yHEADPHONE LEVEL Adjusts the monitor level through the headphone jack. uHEADPHONE JACK Use this jack to connect the headphones. Headphones from 8ohm to 600ohm can be used. 150 ohm is recommended. iINPUT SELECT SWITCH Used to select the input to be sent to each PGM channel. It allows for selection of one of the two inputs connected rear panel. When this switch is depressed, the levels of all sources except MIC muted. oGAIN VOLUME Adjust input level of each channel. Set INPUT tSPLIT CUE SWITCH FADER and MASTER FADER to 7-8position. When this switch is ON, the master signal is always Adjust TRIM so that MASTER LED METER heard through the right earcup of the headphone. The flashes occasionally at ±5dB. CUE signal will be heard in the left earcup when that input is selected by the CUE SELECT !0INPUT EQ-HI(Equalizer High) SWITCH( !3) . This enables both programs to be Auxiliary treble knob. Boosts of +6dB and cuts of monitored simultaneously, thus assisting in beat 24dB are possible at 20kHz. mixing. !1INPUT EQ-MID(Equalizer Middle) Auxiliary mid knob. Boosts of +6dB and cuts of 5 24dB are possible at 1kHz. 16 10 LINE 5 15 PCV-150 / PROFESSIONAL MIXING CONTROLLER FOR THE CREATIVE DJ / PRODUCER ALLOWS YOU TO CREATE YOUR OWN MUSIC WITH VESTAX'S UNSURPASSED ENGINEERING AND DESIGN. 150 MASTER LEVEL L -20 MAX -16 -12 -10 -8 -4 -2 0 +2 +4 +8 +12 dB R 17 +6dB OUTPUT BALANCE 18 +6dB L SUB MASTER CUE OUT R MASTER OUT MASTER CUE +6dB 19 20 CROSS FADER L MIN MAX MIN MAX MIN CF ASSIGN MAX PGM 3 PGM 4 TRANSFORMER 12 22 CF ASSIGN PGM 1 PGM 2 TRANSFORMER 21 23 !2INPUT EQ-LOW(Equalizer Low) !9MASTER OUTPUT LEVEL Auxiliary bass knob. Boosts of +6dB and cuts of 24dB are possible at 80Hz. Adjust the signal level output from MASTER OUT jack on the rear panel. !3CUE SWITCH @0MASTER CUE SWITCH Used to send the signal to the monitor section for head phone. Used to send the signal to the monitor section for head phone. !4INPUT FADER @1CROSS FADER Used to adjust input level of the various PGM channels. Usually at 7-8. Mixes the signals assigned by CROSSFADER ASSIGN SWITCH (@2) to left side of the crossfader and right side. When the crossfader is in the center position, both left and right signals can be heard. This is a detachable feder for ease of replacement with CF-PCV when it is worn out. !5PEAK LEVEL METER The bar graph level meters indicate the peak L&R output. !6SUB MASTER OUTPUT LEVEL @2CROSSFADER ASSIGN SWITCH Adjust the signal level output from SUB MATER OUT jack on the rear panel. Used to assign the signals from each of the PGM channels to either side of the crossfader or to the master section. !7CUE OUTPUT LEVEL Adjust the signal level output from CUE OUT jack on the rear panel. @3TRANSFORMER SWITCH !8MASTER BALANCE With the crossfeder moved to either right or left, the opposite program can be heard instantly by pressing the opposite transformer button. Determines balance between left and right channels. 6 REAR PANEL 24 28 26 29 31 33 35 MADE IN CHINA UNDER LICENCE OFVESTAX TOKYO,JAPAN CAUTION WARNING;SHOCK HAZARD-DO NOT OPEN. AVIS;RISQUE DE CHOC ELELCTRIQUE -NE PAS OUVRIR. RISK OF ELECTRIC SHOCK. DO NOT OPEN MASTER SUB MASTER L +4 MIC AC 12V 600mA SERIAL NO. MIC 1 CUE OUT MIC1,2 EFF LOOP INPUT PGM 4 R LINE 5 PGM 3 LINE 4 LINE 3 PGM 2 PHONO 3 PGM 1 LINE 2 PHONO 2 LINE 1 PHONO 1 SEND 0 -10(dB) BALANCE OUT LEVEL R POWER 37 L L L L L R R R R MIC 2 REC OUT MIC 3 AC IN 12V PIN 1 GND PIN 2 HOT R L PIN 3 COLD GND GND GND RETURN 25 27 30 32 @4POWER SWITCH @5AC POWER JACK 34 36 #1CUE OUT JACK The signal selected by CUE SWITCH and MASTER CUE SWITCH is mono output. It can be sampled by connecting to the input of any sampler without hearing over the P.A. constant level output. MASTER OUTPUT LEVEL does not effect level. Connect to the AC-12 adaptor. @6MASTER OUT JACK(UNBALANCE) Parallel out of P.A.output. Connect with the input of power amp. #2LINE INPUT JACK @7MASTER OUT JACK(BALANCE) Input connector for line level equipment such as CD players, tape decks. Parallel output of LINE output, Connect with the input of power amp. #3PHONO INPUT JACK @8BALANCE OUT LEVEL SWITCH Input jack for each PGM turntable. Connect turntable equipped with MM pickup cartridge only. Used to select output level @9SUB MASTER OUT JACK SUB MASTER output jack. Connect to input of #4GROUND TERMINAL Connect this terminal to ground lead of turntable. power amp as monitor in DJ booth or as a separate This helps to reduce noise and hum. sound zone for entrance foyer,etc. #5MIC EFFECT LOOP SEND JACK #0REC OUT JACK Connect to the input of external effects. Output for recording. Connect with the input jack of #6 M IC EFFECT LOOP RETURN JACK the tape deck. Also use for sub output when you need Connect to the output of external effects. the output beside main output. Pre-fader constant level output. INPUT FADER ( !4) and MASTER #7MIC INPUT JACK OUTPUT LEVEL (!9) does not effect level. Input jack of MIC. 7 HOW TO CHANGE THE FADER UNIT Top panel Driver ■HOW TO REMOVE THE CROSSFADER PANEL 1 Remove crossfader knob and 2screws which fix ○ the crossfader panel. 2 Remove the crossfader panel. ○ Crossfader panel Driver Top panel ■HOW TO CHANGE THE FADER UNIT 1 Remove the screws on the fader panel. ○ 2 Remove the fader unit from position in mixer. ○ 3 Carefully remove the multi-cable connector ○ from fader unit. 4 Attach multi-cable connector to new fader unit. ○ 5 Position the fader unit carefully and secure with ○ screws. Note Use a plus driver fitting screw. Caution: When you change any parts, do not loose the screws with marking. CF-PCV For PMC SERIES ( PMC05ProII, PMC06ProA, etc) Insert the multi-cable connector PMC CONNECTOR Set switch to "PCV" position. Set switch to "PMC" position 8 CONNECTIONS SPEAKER SPEAKER CD, MD player, TAP POWER AMPLIFIER[VESTAX PT-X1000A] CHANNEL A MINI MAX CHANNEL B MINI PROTECT B.T.L POWER MAX PEAK PEAK POWER INPUT INPUT ON / OFF CDPLAYER[VESTAX CDPLAYER[VESTAX CDX-35] CDX-35 SPEAKER CDPLAYER[VESTAXCDPLAYER[VESTAX CDX-35] CDX-35] SPEAKER POWER AMPLIFIER[VESTAX PT-X1000A] CHANNEL A MINI MAX CHANNEL B MINI MAX PROTECT B.T.L POWER PEAK PEAK POWER INPUT INPUT ON / OFF LINE1 LINE4 or 5 LINE3 SUB MASTER LINE2 MIC1∼3 MASTER OUT MADE IN CHINA UNDER LICENCE OFVESTAX TOKYO,JAPAN CAUTION WARNING;SHOCK HAZARD-DO NOT OPEN. AVIS;RISQUE DE CHOC ELELCTRIQUE -NE PAS OUVRIR. RISK OF ELECTRIC SHOCK. DO NOT OPEN MASTER SUB MASTER L +4 MIC1,2 EFF LOOP INPUT PGM 4 R MIC AC 12V 600mA SERIAL NO. MIC 1 CUE OUT LINE 5 PGM 3 LINE 3 LINE 4 PGM 2 PHONO 3 PGM 1 LINE 2 PHONO 2 LINE 1 PHONO 1 SEND 0 -10(dB) BALANCE OUT LEVEL R POWER L L L L MIC 2 L REC OUT R R R R MIC 3 PIN 1 GND PIN 2 HOT R L PIN 3 COLD AC IN 12V GND GND GND RETURN GND REC OUT BALANCE OUT TAPE RECORDER, CD, MD, DAT, etc. SEARCH TRACK MIN SEC PITCH KEY REPEAT FRM OPEN/ CLOSE DISPLAY STOP LOCATE POINT FOCUS ENTER 1 2 3 REVERSE LOOP A PLAY/PAUSE CUE MONITOR START END RELOOP/EXIT GND GND RETURN SEND PHONO2 PHONO1 B PLAY/PAUSE CUE PHONO3 SPEAKER SPEAKER TURNTABLE[VESTAX PDX-2000] TURNTABLE[VESTAX PDX-2000] IN OUT POWER AMPLIFIER[VESTAX PT-X1000A] CHANNEL A CHANNEL B EFFECTOR ( DELAY, REV PROTECT B.T.L POWER PEAK PEAK POWER INPUT INPUT ON / OFF SEARCH TRACK MIN SEC PITCH KEY REPEAT FRM OPEN/ CLOSE MINI MAX MINI MAX DISPLAY STOP LOCATE POINT FOCUS ENTER 1 2 3 REVERSE LOOP A PLAY/PAUSE TURNTABLE[VESTAX PDX-2000] 9 CUE MONITOR START END RELOOP/EXIT B PLAY/PAUSE CUE SPECIFICATIONS INPUT unbalanced OUTPUT unbalanced balanced FREQUENCY RESPONSE FADER CROSS TALK S/N POWER WEIGHT DIMENSIONS NOMINAL MAXIMUM IMPEDANCE MIC INPUT LINE 1-3 PHONO 1-4 -54dBv -10dBv -45dBv -20dBv -20dBv 47k ohm 30k ohm 47k ohm EFFECT RETURN IN -29dBv -21.5dBV 10k ohm MASTER OUT SUB MASTER OUTPUT CUE OUT REC OUTPUT MASTER OUT LINE 1-5 LINE L-R 0dBv 15.5dBv 1k ohm 0dBv 15.5dBv 1k ohm -10dBv 17.5dBv 1k ohm -10dBv -4dBv 220 ohm 0dBv 15.5dBv 1k ohm 20Hz-20kHz(±1.5dBV) more than 60dB CROSSFADER PGM1-3 LINE 1-5 W * H * D(mm) 10 more than 80dB 80dB AC 12V 1000mA 7kg 482 * 84 * 220 Vestax Corporation JUN.2001 PCV150 E2