Download Art CX310 Operating instructions

CX310
Stereo 2-Way / Mono 3-Way Active Crossover
SERVICE GUIDE
IMPORTANT SAFETY INSTRUCTIONS – READ FIRST
This symbol, wherever it appears,
alerts you to the presence of uninsulated
dangerous voltages inside the enclosure that
may be sufficient to constitute a risk of shock.
This symbol, wherever it appears, alerts you
to important operating and maintenance
instructions in the accompanying literature.
Please read the manual.
Read instructions
Retain these safety and operating instructions for future reference. Heed all warnings printed here and on the
equipment. Follow the operating instructions printed in this user guide.
Do not open
There are no user serviceable parts inside. Refer any service work to qualified technical personnel only.
Power sources
Only connect the unit to mains power of the type described in this user guide or marked on the rear panel. The
power source must provide a good ground connection.
Power cord
Use the power cord with sealed mains plug appropriate for your local main supply as provided with the
equipment. If the provided plug does not fit into you outlet consult your service agent. Route the power cord so
that it is not likely to be walked on, stretched or pinched by items placed upon or against.
Grounding
Do not defeat the grounding and polarization means of the power cord plug. Do not remove or tamper with the
ground connection on the power cord.
Moisture
To reduce the risk of fire or electrical shock, do not expose the unit to rain, moisture or use in damp or wet
conditions. Do not place container of liquid on it, which may spill into any openings
Heat
Do not locate the unit in a place close to excessive heat or direct sunlight, as this could be a fire hazard.
Locate the unit away from any equipment, which produces heat such as: power supplies, power amplifiers and
heaters.
Environment
Protect from excessive dirt, dust, heat, and vibration when operating and storing. Avoid tobacco ash, drink
spillage and smoke especially that associated with smoke machines.
Handling
Protect the controls from damage during transit. Use adequate padding if you need to ship the unit. To avoid
injury to yourself or damage to the equipment take care when lifting, moving or carrying the unit.
Servicing
Switch off the equipment and unplug the power cord immediately if it is exposed to moisture, spilled liquid or
the power cord or plug becomes damaged during a lightning storm or if smoke odor or noise is noted. Refer
servicing to qualified technical personnel only.
Installation
Install the unit in accordance with the instruction printed in the user guide.
2
IMPORTANT SAFETY INSTRUCTIONS – READ FIRST ............................................................2
OVERVIEW .....................................................................................................................................................4
Features ...........................................................................................................................................................4
INSTALLATION .............................................................................................................................................5
AC POWER HOOKUP......................................................................................................................................5
INPUT/OUTPUT CONNECTIONS ....................................................................................................................5
MONO 3-WAY CONFIGURATION ...................................................................................................................5
Connections:..................................................................................................................................................5
Controls: ........................................................................................................................................................5
OPERATION......................................................................................................................................................6
FRONT PANEL CONTROLS ...................................................................................................................6
POWER SWITCH..........................................................................................................................................6
CLIP INDICATORS .......................................................................................................................................6
INPUT LEVEL CONTROLS...........................................................................................................................6
MUTE SWITCHES ........................................................................................................................................6
LOW AND HIGH OUTPUT LEVEL CONTROLS...........................................................................................6
CROSSOVER FREQUENCY CONTROLS and RANGE SWITCHES ..........................................................7
REAR PANEL CONNECTORS and CONTROLS .............................................................................7
XLR JACKS ...................................................................................................................................................7
1/4” PHONE JACKS ......................................................................................................................................7
MONO/STEREO MODE SWITCH.................................................................................................................7
APPLICATIONS ............................................................................................................................................8
Typical Setup...................................................................................................................................................8
Signal Flow ......................................................................................................................................................8
Initial Setup Tips .............................................................................................................................................8
SERVICE PARTS .........................................................................................................................................9
FULL BILL OF MATERIALS ...................................................................................................................10
Assembly .......................................................................................................................................................10
Main Ckt Board..............................................................................................................................................11
SCHEMATICS ..............................................................................................................................................13
WARRANTY INFORMATION ................................................................................................................15
Limited Warranty...........................................................................................................................................15
SERVICE ........................................................................................................................................................16
SPECIFICATIONS......................................................................................................................................17
3
OVERVIEW
The ART CX310 Stereo 2-Way/ Mono 3-Way Active Crossover is a perfect addition to any sound
reinforcement system. Designed for PA and fixed-installation applications, the CX310 employs 24dB/
octave state-variable, fourth-order, Linkwitz-Riley filters. These filters guarantee in-phase outputs at
all frequencies. This ensures the proper acoustic summing of common signals from adjacent drivers
in the crossover region.
The CX310 may be used as either a stereo 2-way crossover network, splitting the signal in each
channel into two separate frequency ranges (Lo and Hi), or as a mono 3-way crossover network,
splitting one signal into three separate frequency ranges (Lo, Mid and Hi).
Each channel features input level, high and low output level and crossover frequency rotary controls.
A frequency x10 switch is provided for varying the crossover frequency from the standard 80Hz 920Hz to 800Hz - 9200Hz. Front-panel output mute switches are provided for each individual output
to ease system setup. The rear panel features balanced XLR and 1/4” TRS input and output
connectors as well as a 2-way/ 3-way mode selector switch. Power for the CX310 is internal.
The ART CX310 Stereo 2-Way/ Mono 3-Way Active Crossover has the features and performance you
need for any audio application requiring a crossover. Housed in a rugged all-steel chassis, the model
CX310 will provide years of reliable and continuous service.
Features
• Stereo 2-way or mono 3-way configurations
• Fourth-order Linkwitz-Riley filters
• Balanced XLR and 1/4" TRS input and output connectors
• Adjustable crossover frequency range (80Hz to 920Hz or 800Hz to 9.2kHz)
• Independent output level control for each output
• Individual output muting switches
• Clipping indicators on all outputs
• Rugged, fully shielded all-steel chassis
• Internal AC power supply
• Three year warranty
4
INSTALLATION
The ART CX310 may be used in a wide variety of applications and environments. Enclosed in a 1U
(1.75 inches high) rack-mountable, all-steel enclosure, the unit is designed for continuous
professional use. The depth is 6.5 inches, exclusive of the power cord. Mounting location is not
critical. However, for greater reliability, we recommend that you not place the unit on top of power
amps or other sources of heat.
AC POWER HOOKUP
The CX310 has an internal power supply designed to operate from 105 to 120VAC at 50/60Hz.
Export units are configured with a different power cord and the voltage switch is set for the country of
destination. Before plugging the CX310 into the AC mains, make sure that all of the equipment
following the crossover outputs are turned off or that all of the outputs are turned down.
INPUT/OUTPUT CONNECTIONS
The CX310 has XLR and 1/4" TRS phone jack connectors for each input and output. All connections
are active balanced although the 1/4" phone jack connections can easily be converted to unbalanced
operation by using two-conductor phone plugs. Inserting a plug into a 1/4" jack disconnects the
associated XLR connector.
MONO 3-WAY CONFIGURATION
This information is intended to clarify how the CX310 is used in the mono 3-way configuration.
Connections:
Input
Low Output
Mid Output
High Output
Channel One INPUT
(Channel Two INPUT not used)
Channel One LOW OUTPUT
Channel Two LOW OUTPUT
Channel Two HIGH OUTPUT
(Channel One HIGH OUTPUT not used)
Controls:
Input Level
Low Output Mute
Low Output Level
Low/Mid Crossover
Mid Output Mute
Mid Output Level
Mid/High Crossover
High Output Mute
High Output Level
Channel One INPUT LEVEL control
Channel One LOW MUTE switch
Channel One LOW OUTPUT LEVEL control
Channel One RANGE switch and FREQUENCY control
(Channel One HIGH MUTE switch and
HIGH OUTPUT LEVEL control not used)
(Channel Two INPUT LEVEL control not used)
Channel Two LOW MUTE switch
Channel Two LOW OUTPUT LEVEL control
Channel Two RANGE switch and FREQUENCY control
Channel Two HIGH MUTE switch
Channel Two HIGH OUTPUT LEVEL control
5
OPERATION
FRONT PANEL CONTROLS
POWER SWITCH
The POWER switch applies and removes power to the unit. Make sure that all equipment after the
CX310 is either off or the outputs are turned all the way down before turning the CX310 on or off.
CLIP INDICATORS
Separate HIGH and LOW CLIP indicators are provided for each channel of the CX310. These
indicators will light at approximately 3dB before clipping occurs in any stage of the channel. To
prevent overloading the channel, either turn down the CX310 input control or turn down the output
level of the piece of equipment feeding the CX310 (i.e. mixer, equalizer or other piece of processing
equipment.).
INPUT LEVEL CONTROLS
An INPUT LEVEL control is provided on each channel of the CX310. If you are using the CX310 as a
mono 3-way crossover, the Channel One INPUT CONTROL is the only one used. The INPUT LEVEL
control should be set at its 0 marking in most cases. Increasing or decreasing gain should only be
done to make up for deficiencies in other parts of the system.
MUTE SWITCHES
MUTE switches are provided for each output on the CX310. These are intended for use when setting
up your system and testing either the crossover frequency point or the separate amplifiers and
speakers they are feeding. These switches allow you to isolate a specific frequency output on a
specific channel for fine-tuning or troubleshooting. It is not recommended that you mute or un-mute
any frequency band during normal usage. Levels should be turned down when the MUTE switches
are activated or de-activated.
LOW AND HIGH OUTPUT LEVEL CONTROLS
Each channel of the CX310 has LOW and HIGH OUTPUT LEVEL controls. These controls are used
to trim the output levels to the LOW and HIGH OUTPUT jacks on the rear of the unit, respectively. If
you are using the CX310 as a mono 3-way crossover, the Channel One LOW OUTPUT LEVEL
control sets the level of the LOW OUTPUT, the Channel Two LOW OUTPUT LEVEL control sets the
level of the MID OUTPUT, and the Channel Two HIGH OUTPUT LEVEL control sets the level of the
HIGH OUTPUT.
6
These controls attenuate only (there is no gain). In most cases you would set them to 0 (fully
clockwise). You can use these controls to prevent overdriving the inputs of your amplifiers or to
compensate for variations in amplifier gain or speaker efficiency. Additionally, you can use these
controls to balance the level between highs and lows in your system.
CROSSOVER FREQUENCY CONTROLS and RANGE SWITCHES
Each channel of the CX310 has a crossover FREQUENCY control and RANGE switch to set the
crossover point for the high and low frequencies. These controls cover the frequency range of 80Hz 920Hz, with the RANGE switch in the out position (x1), or 800Hz to 9.2kHz, with the RANGE switch
in the in position (x10). All frequencies below the set frequency will be sent to the LOW OUTPUT and
all frequencies above will be sent to the HIGH OUTPUT.
When the CX310 is used as a stereo 2-way crossover, both RANGE switches will most commonly be
used in the out position (80Hz-920Hz). When used as a mono 3-way crossover, the Channel One
FREQUENCY control is used to set the Low/Mid frequency point and the Channel Two
FREQUENCY control is used to set the Mid/High frequency point. In this case, the Channel One
RANGE switch will most commonly be used in the out position (80Hz-920Hz), while the Channel
Two RANGE switch will most commonly be used in the in position (800Hz-9.2kHz).
The crossover filters are 4-pole Linkwitz-Riley designs (24dB/octave). This yields a sharp roll off to
help protect speakers and the outputs sum to a flat response.
NOTE:
Never change the frequency range switches (from x1 to x10 position - or vice versa) with the
crossover passing audio signals. This may produce transients that can damage speakers.
REAR PANEL CONNECTORS and CONTROLS
It is easy to interface the unit with a wide variety of equipment. The rear panel has balanced XLR and
1/4” phone jack connectors.
XLR JACKS
The XLR connections are balanced and follow the AES standard for wiring: Pin 1 = Ground, Pin 2 =
Hot (+) and Pin 3 = Cold (-). These connectors directly parallel the associated 1/4” connectors.
1/4” PHONE JACKS
The 1/4” connections are balanced with Tip = Hot (+), Ring = Cold (-), and Sleeve = Ground. A twoconductor (tip and sleeve) shorts the Cold (-) and Ground connections together to convert to
unbalanced operation. Inserting a plug into a 1/4" jack disconnects the associated XLR connector.
MONO/STEREO MODE SWITCH
This switch configures the CX310 for stereo 2-way operation with the switch in the out position or for
mono 3-way operation with the switch in the in position.
7
APPLICATIONS
The following guidelines refer to a P.A. system, but the same basic ideas apply to a home recording
setup or a Hi-Fi system.
Typical Setup
For a stereo 2-way system, separate high frequency (horn or tweeter) and low frequency (bass or
subwoofer) speaker cabinets are used for each channel (left and right) of the stereo sound system
and are driven by their own power amplifiers. For a mono 3-way system, separate high frequency
(horn or tweeter), mid frequency (mid or full range) and low frequency (bass or subwoofer) cabinets
are used for each channel of the sound system.
The crossover is used to split each channel's signal into two or three frequency bands, which feed
separate amplifiers. This delivers the proper frequencies to each speaker cabinet as well as allowing
its associated amplifier to produce acoustic power more efficiently.
Note: You will need two 310 crossovers if your three-way system is stereo.
It is very important that you use caution when selecting the crossover points for any system.
Refer to the documentation that came with your speaker cabinets for information on their
proper frequency ranges. This is especially important for high frequency horns; damage may
occur from sending lower frequencies than specified into the drivers!
Signal Flow
In most situations, the crossover is the last piece of equipment in the signal chain before the power
amplifiers. Signal flow is as follows:
Mixer → Equalizer → Crossover → Power Amplifier → Speaker Cabinets
Sometimes a limiter is placed between the mixer outputs and the equalizer or after the equalizer for
system protection.
Initial Setup Tips
1.
2.
3.
4.
5.
6.
7.
8.
9.
Set all level controls to their full counter-clockwise position.
Connect the output(s) of your mixer (or equalizer) to the input(s) of the CX310. If stereo,
Channel One is left.
Connect the LOW OUTPUT of each channel (LOW OUTPUT of Channel One for mono
3-way configuration) to the power amplifier powering the low frequency cabinet(s).
If set for mono 3-way, connect the MID output (LOW OUTPUT of Channel Two) to the
power amplifier powering the mid frequency cabinet.
Connect the HIGH OUTPUT of each channel (HIGH OUTPUT of Channel Two for mono
3-way configuration) to the power amplifier powering the high frequency cabinet(s).
Set the crossover frequency for each channel (they should be the same if your PA
cabinets are the same) or each frequency band for mono 3-way configuration.
With the power amplifier volume controls turned all the way down, turn on all equipment in
the system.
With a program source running through the system, turn up the power amplifier volume
controls and slowly turn up the crossover input level controls while checking for clipping.
Turn up each of the crossover's output level controls while checking each individual output
for sound and performance.
8
SERVICE PARTS
PART #
DESCRIPTION
PART USAGE
SWT DPDT LATCHING
CON JACK 1/4" STEREO
RSP POT 10KB
RSP POT 50KX4
switches for low mute,
range, high mute,
mono/stereo
input and output jacks
level pots
frequency pots
310-2003-101
MLD CAP SWITCH BLACK
switch caps for low mute,
range, high mute,
mono/stereo
310-2004-101
310-2005-101
MLD CAP POT BLK,GREY CAP
W/WHITE LINE
CON FUSE 1/2 A 5X20MM SLO-BLO
100-5021-101
100-5225-102
310-2001-101
310-2002-101
341-2008-101
341-2009-101
310-2006-101
CON JACK XLR MALE
CON JACK XLR FEMALE
XFM POWER SUPPLY BOARD
UPDATED
3102007101
3102008101
1005269104
DIG I.C. JRC2068
DIG I.C. HCF4068
Pwr swt SPST 6A w/LED
LOCATION
(ALL)
IN/OUTPUTS
FREQUENCY
All switches
All pots
fuse
output jacks
input jacks
X4, X6,
HIGHOUTPUT*2
X1, X5
New XFM TFC006EIS1
IC101-104, IC108-109,
IC 111-112
IC113, IC213
Front panel
9
FULL BILL OF MATERIALS
Assembly
ART part# Vendor part#
3102006101 APDR016001
APDR016002
APDR056002
1001094110 FU31502D21
JAH20622I1
3102003101 KPCR061201
3102004101 KPCT131602
3102001201 MBP00R0261
3102003201 MCP00R0261
3102002201 MPP00R0261
MFS00R0561
DESCRIPTION
power board module CX-152/SE-100A
ART-310 main board DIP
LED board DIP
fuse 0.5A/250V 5*20mm SLOW BLOW
FUSE-HOLDER CQ-206F
button P-08 M704Y1001H01 SQ BLK SWT CAP
knob CP-MB1-5-T18(M704D0001H15 POT KNOBS
chassis FOR ART-311 black
top cover, black
front plate CX311 black silk-printing
front stand
LOCATION
Shelf-finished
Shelf-finished
Shelf-finished
Slow-off type
lock LED board to the front
stand
NSA3006RB1 screw M3*6mm black
NNN3025HN1 nut M3*2.5mm tinning
GE026BAGL1
GR025INBP1
GE136BAGL1
GA136BAGL3
GE136CSHC1
3102004102 GR026G0001
4
1
NSA3006FB1 screw M3*6mm black
NSA3016PB1
NSM3008PB1
NSS3006PB1
NWG35071N1
1005269104 SW18110002
NSM3006PB1
SW09120001
WPE13633F2
WPS08663H1
QTY
1
1
2
1
1
7
8
1
1
1
1
screw M3*16mm﹐round, black FOR 1U
screw M3*8mm round black
screw M3*6mm round black
Plum meson d=3.5mm*D=7mm
switch 6A with LED
screw M3*6mm round black
switch 115V/230V
power cord USA round 180 degree SVT 18#*3G
power cord Europe 90 degree ,H030 75m 2*3G
CX-310 packaging
plastic bag 170*270*0.04mm
gift box FOR ART-CX
plastic bag 260*570*0.07mm
plastic bag 120x250x0.07mm w/warning mark
rubber feet 1U EPE
EPE, white
manual FOR CX-310
10
lock cover, front stand, L type
plate to chassis
lock front plate to front stand
lock ground lug
lock XLR
lock ground lug
lock switchable switch
USA +205# terminal
Europe +205# female terminal
for manual
FOR UNIT
FOR UNIT
FOR POWER CORD
16
4
2
12
1
1
2
1
1
1
1
1
1
1
2
1
Main Ckt Board
ART part#
Vendor part#
DESCRIPTION
LOCATION
QTY
CX310 MAIN CKT BOARD
1001037111
CC1040B4M2 .1uf/50v CC
±20% 5.0mm TAPING
CC2210B4K2 220P/50V CC 10% 5.0mm TAPING
CC2210B4M2 220PF/50V CC ±20% 5.0mm TAPING
C107 108 207 208
C104 102 118 125 128 135
204 202 218 225 228 235
R184 186 284 286
4
12
4
1001162124
CE107022M2 100UF/25V EC ±20% 5.0mm TAPING
1001162109
CE476021M2 47UF/16V EC ±20% 5.0mm TAPING
C120 122 130 132 141-145
220 222 230 232 241-245
C166 167 266 267
CE477022M2 470uF/25V EC ±20% 5.0mm TAPING
C137 138 237 238
4
CM1530B5J2 0.015UF/100V PEI ±5% 5.0mm TAPING
8
RE815013F4 1.5K1/4W
TAPING
RE815423F4
±1%
15.4K1/4W ±1%
2.49K1/4W ±1%
2.67K1/4W ±1%
27.4K 1/4W ±1%
TAPING
R141 241
2
TAPING
R142 242
2
TAPING
R171 172 271 272
4
TAPING
R124 131 224 231
4
CM8220B5J2 8200PF/100V PEI ±5% 5.0mm TAPING
CZ1040B4M2 0.1UF/50V±20% 5.0mm X7R TAPING
DE24148001 diode IN4148 TAPING
DE35235001 diode IN5235B(1/2W 6.8V) TAPING
RE115043J4 1.5M1/4W
1001001401
1001001339
4
C109-112 C209-212
C117 124 127 134 157 160
161 164 217 224 227 234 257
260 261 264
C168 267
C103 106 119 126 129 136
156 158 162 163 165 200 203
219 226 229 236 159 256 258
259 262 263 265
D101-104 D201-204
D105 106 205 206
R173 R174 R177 R178 R273
R277 R274 R278
R121 123 126 129 140 144
155-162 176 221 223 226 229
240 244 255-262 276 184-188
284-288
R107 108 111 112 122 128
175 207 208 211 212 222 228
275
R106 109 110 113 206 209
210 213
R168 179 268 279
CM1820B5J2 1800PF/100V PEI ±5% 5.0mm TAPING
1001029101
1001030104
18
±5%
TAPING
RE810023F4 10K1/4W
±1%
TAPING
RE810033F4 100K1/4W
±1%
TAPING
RE815003F4 1501/4W
±1%
TAPING
RE824913F4
RE826713F4
RE827423F4
16
2
24
8
4
8
40
14
8
4
1001001354
RE835713F4 3.57K1/4W
±1%
TAPING
R143 145 243 245
4
1001001358
RE839213F4 3.92K1/4W
±1%
TAPING
R139 239
2
1001001368
RE849913F4 4.99K1/4W ±1%
TAPING
R125 130 225 230
4
RE856203F4 5621/4W
±1%
TAPING
R181 182 281 282
4
RE875013F4 7.5K1/4W
±1%
TAPING
R127 227 120 220
4
RE882503F4 8251/4W
±1%
TAPING
R183 283
2
CS1040IDK1 0.1UF/400V±10% 15.0mm
C101
1
IC2068DD11 IC NJM2068DD DIP8
IC101-104 108 109 111 112
201-204 208 209 211 212
16
3102007101
11
ART part#
Vendor part#
DESCRIPTION
LOCATION
QTY
IC4066BP11 IC TC4066BP DIP
IC113 213
2
JAB00321I1 jack BASE A2501-WV2-3P
J101
1
RE6220B4J4 2.2R MO 1/2W ±5% TAPING
R102 103
2
RE7B1032G5 8PIN 1/8W B103 ±2%
RP101 102 105 106 107 108
201 202 205 206 207 208
12
1005225102
JA406311L2 jack PHONE D=6.3mm JLJ0661-6
IN1*2 X2-4 X6
6
3412009101
JA700311L1 jack XLR JACK female 94M-007P1
X1 X5
2
3412008101
JA700321L1 jack XLR JACK male 93M-108P1
X7 X8 HIGH OUT1*2
4
3102002101
VR3B503213 B50K*4 VR RV124NG KQ15mm ±10%
VR104 VR204
2
3102001101
VR5B10321D B10K
VR101 102 103 201 202 203
6
1005021101
SW03220001 SWT DPDT LATCHING switch PS-909L-22
SW102--SW104
SW205
7
3102008101
±20%
VR RV1210 KQ 15mm
SW202-
CX310 LED ASSEMBLY
1001031111
PCR056251A printing circuit FOR CX-152LED board \ 94V0 1.6mm
1
DE51103001 diode D=3mm red
2
EXLEDR0561 LED SUPPORT LED-8 L= 8mm白白
2
CX-310 POWER CKT BOARD ASSEMBLY
1001037111
CC1040B4M2 CC 0.1UF/50V ±20% 5.0mm TAPING
C4 5 8 9 12 13
6
CC4720DDM1 4700PF/400V±20% 10.0mm
C10
1
C1
1
±10%10.0mm
CD4710DTK1 Surge absorber 14D 471
1001162112
CE108021M1 EC 1000UF/16V
±20%5.0mm
C6 7
2
1001162107
CE228033M1 EC 2200UF/35V
±20%7.5mm
C2 3
2
DE70W04001 Bridge rectifier W04M 1A/400V
DB1
1
1001042102
IC00781552 IC 7815 TO-220
IC1
1
1001042101
IC00791552 IC 7915 TO-220
IC2
1
RE112013J1 1.2K 1/4W ±5% MINI F-TYPE
IC3 1-3
1
TFC006EIS1 power supply EI-41 115/230V PIN TYPE FOR CX
12
1
SCHEMATICS
1
2
3
4
RP101
B103J
1
R188
10K
5+ 7
_
6 JRC2068DD
IC101B
D
INPUT
VR101 C142
B10K 100uF/25V
R183
D104
D101
D102
D103
C104
IN4148 IN4148 IN4148 221P
IN4148
-15V
SW101 825R
CD Boost
TO CH2 B1 IN
1
VR104B
B50K
R158
10K
R157
10K
B
10K
C161
182J
R178
C109
153J
1M5
R177
1M5
IC102B
JRC2068DD
_ 6
7
5
+
1
7
D106 10K
6V8
IC103B
JRC2068DD C111
153J
6_
7
5
+ C160
182J
C164
182J
R173
1M5
R174
1M5
R139
3K92
R162
6_
5
+
C112
153J
IC102A
JRC2068DD
_ 2
1
3
+
J102
1K5
R179
3
2
1
VR104D
B50K
R161
10K
R182
560R -15V
R175 D105
100K 6V8
10K
R143
3670R
10K
IC113
TC4066BP
R144
R141
15K4
C110
153J
8
SW104
Range
R176
2490R
10K
+15V
R181
560R
C167
47uF/16V
_ 2
3
+
R159
R110
150R
221P
IC108B
JRC2068DD C128
C127
182J
-15V
R140
10K
R145
3570R
R155
C166
10K
47uF/16V IC104A
VR104A
JRC2068DD
B50K
_ 2
1
3 R156
+
10K
C157
182J
R168
IC104B
JRC2068DD
1
2
3
HIGH OUT
XLR
R112
100K
1
C120
100uF/25V
R106
150R
7
C117
182J
1
R109
150R
C125
IC109A
JRC2068DD 221P
C124
182J
R107
100K
C
C122
100uF/25V
LOW OUT
R120
22K
4
C138
470uF/25V
R171 R121 R123
2670R 10K 10K
R108
100K
XLR
1
104M5Z 104M5Z 104M5Z 104M5Z 104M5Z 100uF/25V 100uF/25V
C106
C165 C162
C145
C136 C126
C158
C144
104M5Z
C137
C107
470uF/25V104Z
_
4
_
4
_
4
_
4
_
4
_
4
_
4
_ -15V
IC101
IC102
IC103
IC104
IC108
IC109
IC111
IC112
8 +
8 +
8 +
8 +
8 +
8 +
8 +
8 +
+15V
R186
10K
2_
3
+
SW6B
2
C134
182J
C118
IC109B
JRC2068DD 221P
C141
C143
C103
C163
C159
C156
C129
C119
104M5Z 104M5Z 104M5Z 104M5Z 104M5Z 104M5Z 100uF/25V 100uF/25V
C108
104Z
1
IC112A
R125
4990R R124 R187 JRC2068DD
27K4 10K
P102
LED101
Low
5
+
6_
+15V
R122
VR102
B10K
LED102
High
R129 R126
10K 10K
221
7
C132
100uF/25V
2
100K_ 6
7
5
+
SW102
Low Mute
D
R111
100K
1
3
+
2_
IC112B
JRC2068DD
1K5
SW6A
Hi Phase
B103J RP105
R128
100K
+15V R127
1K5
C130
100uF/25V
R113
150R
1
C135
IC108A
JRC2068DD 221P
B103J
R184
RP106
JRC2068DD 10K
VR103 IC1112A
2_
SW103
B10K
1
1
3
Hi Mute
+
R130
R172
4990R R131 R185
27K4 10K
2670R
IC111B
JRC2068DD
5
7
+
_ 6
R142
VR104C
B50K
R160
7
3
+
2_
822J/100V
+15V
C
1
5
+
6_
3+ 1
_
2 IC101A
C168 JRC2068DD
8
B103J
RP107
221
IC103A
JRC2068DD
7
1
1
C102
221P
6
RP108
B103J
RP102
B103J
1
2
INPUT
5
B
R102
R103
2R2 1/2W 2R2 1/2W
J101
1
2
3
1K2
C101
POWER
P4
2
1
104K/400JS
RED
G2
P1
250V/0.5A
POWER
AC230V
~
AC115V
POWER SW
A
LC-410104
AC230/110V
C13
104Z/Y5V
C10
472M/400-AA
C12
104Z/Y5V
~
DB1
W04M
1
+
_
POWER
1
2
3
7815
C3
2200uF/35V
C4
104Z/Y5V
C12
470uF/16V
C2
2200uF/35V
C5
C7
470uF/16V
104Z/Y5V
1
7915
15V
P1
C8
1
2
3
104Z/Y5V
15V
A
C9
104Z/Y5V
Title
Size
Number
CH1
Cx310
Revision
A2
Date:
File:
1
2
3
4
5
13
6
7
19-Dec-2001
Sheet of
Drawn By:
8
1
2
3
4
5
6
D
RP201
B103J
1
2
5
6
R288
10K
7
+
_
VR201 C242
B10K 100uF/25V
IC201B
JRC2068DD
INPUT
R283
D204
In4148
-15V
1
1
C202
221P
INPUT
D201
D202
D203
C204
In4148 In4148 221P
In4148
SW201 825R
CD Boost
3+
_
2
5
+
6_
IC201A
JRC2068DD
C268
822J/100V
3
+
2_
C
IC203A
JRC2068DD
1
VR204B
B50K
VR204C
B50K
R260
_ 2
3
+
10K
C261
182J
R258
10K
C209
153J
R278
1M5
R277
1M5
R259
10K
IC202B
JRC2068DD
_ 6
7
5
+
C264
182J
R262
10K
R276
C267
47uF/16V
8
SW204
Range
R281
560R
1
7
D206 10K
6V8
R275 D205
100K 6V8
B
IC203B
JRC2068DD C211
153J
6_
7
5
+ C260
IC213
TC4066BP
R273
1M5
R274
1M5
182J
R239
3K92
6_
5
+
C212
153J
10K
R243
3670R
C210
153J
+15V
R244
R241
15K4
IC202A
JRC2068DD
_ 2
1
3
+
VR204D
B50K
R261
10K
R282
560R -15V
R240
10K
J102
R279
3
2
1
1K5
-15V
R245
R255
C266
10K
47uF/16V IC204A
VR204A
JRC2068DD
B50K
_ 2
1
3 R256
+
10K
C257
182J
R268
1K5
R222
IC204B
JRC2068DD
1
2
3
R212
100K
1
SW206B
C
C220
100uF/25V
R206
150R
7
C217
182J
R207
100K
C222
100uF/25V
1
R209
150R
C225
IC209A
JRC2068DD 221P
C224
182J
C237 C207
470uF/25V 104Z
+15V
R220
22K
LOW OUT
C238
470uF/25V
R271 R221 R223
2670R 10K 10K
R208
100K
1
X6(XLR)
C245
C244
C206 C265 C262
C258 C236 C226
104M5Z 104M5Z 104M5Z 104M5Z 104M5Z 104M5Z 100uF/25V 100uF/25V
4
_
4
_
4
_
4
_
4
_
4
_
4
_
4
_ -15V
IC101
IC102
IC103
IC104
IC108
IC109
IC111
IC112
8 +
8 +
8 +
8 +
8 +
8 +
8 +
8 +
B
+15V
C208
104Z
1
IC212A
R225
4990R R224 R287 JRC2068DD
27K4 10K
P202
LED201
Low
2_
3
+
XLR
C218
IC209B
JRC2068DD 221P
R286
10K
VR202
B10K
LED202
High
R229 R226
10K 10K
100K_ 6
7
5
+
SW202
Low Mute
2
C234
182J
2
221P
7
5
+
6_
3
+
2_
IC212B
JRC2068DD
3570R
HIGH OUT
1
R228
100K
+15V R227
1K5
R211
100K
C232
100uF/25V
R213
150R
1
SW206A
Hi Phase
B103J
RP205
R184
RP206
JRC2068DD 10K
VR203 IC212A
B103J
_
2
B10K
SW203
1
1
3
Hi Mute
+
R230
R272
4990R R231 R285
27K4 10K
2670R
IC211B
JRC2068DD
5
7
+
_ 6
2490R
R242
C227
182J
C235
IC208A
JRC2068DD 221P
221P
C230
100uF/25V
R210
150R
7
C228
IC208B
JRC2068DD 221P
+15V
R257
10K
1
Mode Mono/Stereo
SW205
TO-CH1 B1 OUT
1
D
B103J
RP207
RP208
B103J
RP202
B103J
1
8
7
C243
C203 C263 C259 C256 C229 C219 C241
104M5Z 104M5Z 104M5Z 104M5Z 104M5Z 104M5Z 100uF/25V 100uF/25V
R202
R203
2R2 1/2W 2R2 1/2W
J201
1
2
3
POWER
A
A
Title
Size
Number
CH2
Cx310
Revision
A2
Date:
File:
1
2
3
4
5
14
6
7
19-Dec-2001
C:\temp\CX-152-B1.DDB
Sheet of
Drawn By:
YUYEQI
8
WARRANTY INFORMATION
Limited Warranty
Applied Research and Technology will provide warranty and service for this unit in accordance with
the following warrants:
Applied Research and Technology, (ART) warrants to the original purchaser that this product and the
components thereof will be free from defects in workmanship and materials for a period of three
years from the date of purchase. Applied Research and Technology will, without charge, repair or
replace, at its option, defective product or component parts upon prepaid delivery to the factory
service department or authorized service center, accompanied by proof of purchase date in the form
of a valid sales receipt.
This warranty does not apply in the event of misuse or abuse of the product or as a result of
unauthorized alterations or repairs. This warranty is void if the serial number is altered,
defaced, or removed.
ART reserves the right to make changes in design or make additions to or improvements upon this
product without any obligation to install the same on products previously manufactured.
ART shall not be liable for any consequential damages, including without limitation damages resulting
from loss of use. Some states do not allow limitations of incidental or consequential damages, so the
above limitation or exclusion may not apply to you. This warranty gives you specific rights and you
may have other rights, which vary, from state to state.
For units purchased outside the United States, an authorized distributor of Applied Research and
Technology will provide service.
15
SERVICE
The following information is provided in the unlikely event that your unit requires service.
1. Be sure that the unit is the cause of the problem. Check to make sure that the unit has power
supplied, that all cables are connected correctly, and that the cables themselves are in working
condition. You may want to consult with your dealer for assistance in troubleshooting or testing
your particular configuration.
2. If you believe that the ART unit is at fault, go to www.artproaudio.com. You may contact Customer
Service for more assistance, or directly request a Return Authorization for service in the
“resources” area of the website.
3. If you are returning the unit for service, pack the unit in its original carton or a reasonable
substitute. The original packaging may not be suitable as a shipping carton, so consider putting
the packaged unit in another box for shipping. Print the RA number clearly on the outside of the
shipping box. Print your return shipping address on the outside of the box.
4. Include with your unit: a note with the RA number and your contact information, including a return
shipping address (we cannot ship to a P.O. box) and a daytime phone number, and a description
of the problem, preferably attached to the top of the unit. Also include a copy of your purchase
receipt.
Fill in the following information for your reference:
Date of purchase
___________________
Purchased from
___________________
Serial Number
___________________
16
SPECIFICATIONS
Input Connections
Output Connections
XLR, 1/4” TRS, balanced
XLR, 1/4” TRS, balanced
Frequency Response
10Hz to 20kHz, +0/-1.5dB
Crossover Frequency Range
x1
x10
80Hz to 920Hz
800Hz to 9.2kHz
Crossover Filter Type
Fourth-order Linkwitz-Riley, 24dB/octave
Dynamic Range
Signal to Noise Ratio
118dB
>85dB
Input Impedance
Output Impedance
20k Ohms
150 Ohms
Maximum Input Level
Maximum Output Level
+13dBu
+21dBu
Total Harmonic Distortion (THD)
Maximum Gain
<0.05% (20Hz-20kHz)
+4dB
Power Requirements
105-120V AC, 50-60hz, 3VA (USA)
Export units configured for country of destination
Dimensions (HWD)
1.75” x 19” x 6.5”
44mm x 483mm x 165mm
Weight
7.1 lbs. (3.2 kg)
ART maintains a policy of constant product improvement. ART reserves the right to make changes in
design or make additions or improvements to this product without any obligation to install these
changes on products previously manufactured. Therefore, specifications are subject to change
without notice.
17
www.artproaudio.com
E-mail: [email protected]
© 2010 Applied Research & Technology
CX310
V1.1
18