Download Mitsubishi Electric PKFY-P-VKM-E Service manual

SPLIT-TYPE, HEAT PUMP AIR CONDITIONERS
December 2012
No. OCH447
REVISED EDITION-B
TECHNICAL & SERVICE MANUAL
R410A
Indoor unit
[Model names]
PKFY-P63VKM-E
PKFY-P100VKM-E
R407C
[Service Ref.]
PKFY-P63VKM-E.TH
PKFY-P63VKM-ER1.TH
PKFY-P100VKM-E.TH
PKFY-P100VKM-ER1.TH
R22
Revision:
• PKFY-P63/100VKM-ER1.TH
have been added in
REVISED EDITION-B.
• Some descriptions have
been modified.
• Please void OCH447
REVISED EDITION-A.
Note:
• This manual describes only
service data of the indoor
units.
• RoHS compliant products
have <G> mark on the spec
name plate.
CONTENTS
INDOOR UNIT
1. TECHNICAL CHANGES ......................... 2
2. SAFETY PRECAUTION.......................... 2
3. PART NAMES AND FUNCTIONS .......... 6
4. SPECIFICATION ................................... 14
5. OUTLINES AND DIMENSIONS ............ 16
6. WIRING DIAGRAM ............................... 17
7. REFRIGERANT SYSTEM DIAGRAM........19
8. TROUBLESHOOTING .......................... 19
9. DISASSEMBLY PROCEDURE ............. 27
PARTS CATALOG (OCB447)
1
TECHNICAL CHANGES
PKFY-P63VKM-E.TH
PKFY-P100VKM-E.TH
PKFY-P63VKM-ER1.TH
PKFY-P100VKM-ER1.TH
• INDOOR CONTROLLER BOARD (I.B.) has been changed. (S/W version up)
2
SAFETY PRECAUTION
CAUTIONS RELATED TO NEW REFRIGERANT
Cautions for units utilizing refrigerant R407C
Do not use the existing refrigerant piping.
Do not use a refrigerant other than R407C.
The old refrigerant and lubricant in the existing piping
contain a large amount of chlorine which may cause the
lubricant deterioration of the new unit.
If another refrigerant (R22, etc.) is used, the chlorine in the
refrigerant may cause the lubricant deterioration.
Use “low residual oil piping”
If there is a large amount of residual oil (hydraulic oil, etc.)
inside the piping and joints, deterioration of the lubricant
will result.
Store the piping indoors, and both ends of the
piping sealed until just before brazing.
(Leave elbow joints, etc. in their packaging.)
If dust, dirt, or water enters the refrigerant cycle,
deterioration of the oil and compressor trouble may result.
Use ESTR , ETHER or HAB as the lubricant to
coat flares and flange connection parts.
If large amount of mineral oil enters, that can cause
deterioration of refrigerant oil etc.
Use liquid refrigerant to charge the system.
Use a vacuum pump with a reverse flow check valve.
The vacuum pump oil may flow back into the refrigerant
cycle and cause the lubricant deterioration.
Use the specified refrigerant only.
Never use any refrigerant other than that specified.
Doing so may cause a burst, an explosion, or fire when the
unit is being used, serviced, or disposed of.
Correct refrigerant is specified in the manuals and on the
spec labels provided with our products.
We will not be held responsible for mechanical failure,
system malfunction, unit breakdown or accidents caused
by failure to follow the instructions.
Ventilate the room if refrigerant leaks during
operation. If refrigerant comes into contact with
a flame, poisonous gases will be released.
If gas refrigerant is used to seal the system, the composition
of the refrigerant in the cylinder will change and performance
may drop.
OCH447B
2
[1] Cautions for service
· After recovering the all refrigerant in the unit, proceed to working.
· Do not release refrigerant in the air.
· After completing the repair service, recharge the cycle with the specified amount of liquid refrigerant.
[2] Refrigerant recharging
(1) Refrigerant recharging process
1Direct charging from the cylinder.
· R407C cylinder available on the market has a syphon pipe.
· Leave the syphon pipe cylinder standing and recharge it.
(By liquid refrigerant)
Unit
Gravimeter
(2) Recharge in refrigerant leakage case
· After recovering the all refrigerant in the unit, proceed to working.
· Do not release the refrigerant in the air.
· After completing the repair service, recharge the cycle with the specified amount of liquid refrigerant.
[3] Service tools
Use the below service tools as exclusive tools for R407C refrigerant.
No.
Tool name
Specifications
1
Gauge manifold
2
Charge hose
3
Electronic scale
· Only for R407C
· Use the existing fitting SPECIFICATIONS. (UNF7/16)
· Use high-tension side pressure of 3.43MPa·G or over.
· Only for R407C
· Use pressure performance of 5.10MPa·G or over.
—
4
Gas leak detector
· Use the detector for R134a or R407C.
5
Adaptor for reverse flow check
· Attach on vacuum pump.
6
Refrigerant charge base
7
Refrigerant cylinder
8
Refrigerant recovery equipment
—
· For R407C
· Top of cylinder (Brown)
· Cylinder with syphon
OCH447B
3
—
Cautions for units utilizing refrigerant R410A
Do not use the existing refrigerant piping.
The old refrigerant and lubricant in the existing piping
contains a large amount of chlorine which may cause the
lubricant deterioration of the new unit.
Use the following tools specifically designed for
use with R410A refrigerant.
The following tools are necessary to use R410A refrigerant.
Gauge manifold
Charge hose
Gas leak detector
Torque wrench
Use “low residual oil piping”
If there is a large amount of residual oil (hydraulic oil, etc.)
inside the piping and joints, deterioration of the lubricant
will result.
Tools for R410A
Flare tool
Size adjustment gauge
Vacuum pump adaptor
Electronic refrigerant
charging scale
Handle tools with care.
Store the piping indoors, and both ends of the
piping sealed until just before brazing.
(Leave elbow joints, etc. in their packaging.)
If dirt, dust or moisture enters into refrigerant cycle, that can
cause deterioration of refrigerant oil or malfunction of compressor.
If dirt, dust or moisture enters into refrigerant cycle, that can
cause deterioration of refrigerant oil or malfunction of compressor.
Do not use a charging cylinder.
The refrigerant oil applied to flare and flange
connections must be ester oil, ether oil or
alkylbenzene oil in a small amount.
If large amount of mineral oil enters, that can cause deterioration of refrigerant oil etc.
Charge refrigerant from liquid phase of gas
cylinder.
If the refrigerant is charged from gas phase, composition
change may occur in refrigerant and the efficiency will be
lowered.
Do not use refrigerant other than R410A.
If other refrigerant (R22 etc.) is used, chlorine in refrigerant can cause deterioration of refrigerant oil etc.
If a charging cylinder is used, the composition of refrigerant will change and the efficiency will be lowered.
Use the specified refrigerant only.
Never use any refrigerant other than that specified.
Doing so may cause a burst, an explosion, or fire when the
unit is being used, serviced, or disposed of.
Correct refrigerant is specified in the manuals and on the
spec labels provided with our products.
We will not be held responsible for mechanical failure,
system malfunction, unit breakdown or accidents caused
by failure to follow the instructions.
Ventilate the room if refrigerant leaks during
operation. If refrigerant comes into contact with
a flame, poisonous gases will be released.
Use a vacuum pump with a reverse flow check
valve.
Vacuum pump oil may flow back into refrigerant cycle and
that can cause deterioration of refrigerant oil etc.
OCH447B
4
[1] Cautions for service
(1) Perform service after recovering the refrigerant left in unit completely.
(2) Do not release refrigerant in the air.
(3) After completing service, charge the cycle with specified amount of refrigerant.
(4) When performing service, install a filter drier simultaneously.
Be sure to use a filter drier for new refrigerant.
[2] Additional refrigerant charge
When charging directly from cylinder
· Check that cylinder for R410A on the market is syphon type.
· Charging should be performed with the cylinder of syphon stood vertically. (Refrigerant is charged from liquid phase.)
Unit
Gravimeter
[3] Service tools
Use the below service tools as exclusive tools for R410A refrigerant.
No.
1
Tool name
Gauge manifold
Specifications
· Only for R410A
· Use the existing fitting specifications. (UNF1/2)
· Use high-tension side pressure of 5.3MPa·G or over.
2
Charge hose
· Only for R410A
3
Electronic scale
4
Gas leak detector
· Use the detector for R134a, R407C or R410A.
5
Adaptor for reverse flow check
· Attach on vacuum pump.
6
Refrigerant charge base
7
Refrigerant cylinder
8
Refrigerant recovery equipment
· Use pressure performance of 5.09MPa·G or over.
—
—
· Only for R410A
· Top of cylinder (Pink)
· Cylinder with syphon
OCH447B
—
5
3
PART NAMES AND FUNCTIONS
3-1. Indoor unit
Front grille
Filter
Air inlet
Emergency operation
switch
Air outlet
Louver
Vane
OCH447B
6
3-2. WIRED REMOTE CONTROLLER <PAR-30MAA/PAR-31MAA>
Wired remote controller function
* The functions which can be used are restricted according to the model.
Function
Body
: Supported
PAR-30MAA/PAR-31MAA
Slim
Product size H × W × D (mm)
LCD
: Unsupported
PAR-21MAA
City multi
120 × 120 × 19
120 × 130 × 19
Full Dot LCD
Partial Dot LCD
Backlight
Energy-saving
Energy-saving operation schedule
Automatic return to the preset temperature
Restriction
Setting the temperature range restriction
Function
Operation lock function
Weekly timer
On / Off timer
High Power
Manual vane angle
The functions of the function buttons change depending on
the screen. Refer to the button function guide that appears
at the bottom of the LCD for the functions they serve on a
given screen.
When the system is centrally controlled, the button function
guide that corresponds to the locked button will not appear.
<Main display>
<Main menu>
Fri
Room
Cool
Set temp.
Auto
Mode
Temp.
Fan
Function buttons
F1
F2
F3
Main menu
Vane·Louver·Vent. (Lossnay)
High power
Timer
Weekly timer
OU silent mode
Main display:
Cursor
Page
Function guide
F4
ON / OFF lamp
ON / OFF button
This lamp lights up in green while the unit is in operation.
It blinks while the remote controller is starting up or when
there is an error.
Press to turn ON/OFF the indoor unit.
SELECT button
Press to save the setting.
Function button F1
RETURN button
Main display : Press to change the operation mode.
Main menu : Press to move the cursor down.
Press to return to the previous screen.
Function button F2
MENU button
Main display : Press to decrease temperature.
Main menu : Press to move the cursor up.
Press to bring up the Main menu.
Backlit LCD
Operation settings will appear.
When the backlight is off, pressing any button turns the
backlight on and it will stay lit for a certain period of time
depending on the screen.
When the backlight is off, pressing any button turns
the backlight on and does not perform its function.
(except for the (ON / OFF) button)
OCH447B
Main
7
Function button F3
Main display : Press to increase temperature.
Main menu : Press to go to the previous page.
Function button F4
Main display : Press to change the fan speed.
Main menu : Press to go to the next page.
The main display can be displayed in two different modes: "Full" and "Basic".
The factory setting is "Full". To switch to the "Basic" mode, change the setting on the Main display setting.
<Full mode>
<Basic mode>
* All icons are displayed for explanation.
Fri
Fri
Cool
Room
Cool
Set temp.
Mode
Temp.
Set temp.
Auto
Auto
Mode
Fan
Temp.
Fan
Operation mode
Indoor unit operation mode appears here.
Appears when the buttons are locked.
Preset temperature
Preset temperature appears here.
Clock (See the Installation Manual.)
Appears when the On/Off timer or Night setback function is
enabled.
Current time appears here.
Fan speed
Fan speed setting appears here.
Appears when the Weekly timer is enabled.
Button function guide
Functions of the corresponding buttons appear here.
Appears while the units are operated in the energy-save
mode.
Appears when the ON/OFF operation is centrally controlled.
Appears when the operation mode is centrally controlled.
Appears when the built-in thermistor on the remote controller is activated to monitor the room temperature (a).
appears when the thermistor on the indoor unit is activated to monitor the room temperature.
Appears when the preset temperature is centrally controlled.
Indicates the vane setting.
Appears when the f lter reset function is centrally controlled.
Indicates the louver setting.
Indicates when f lter needs maintenance.
Room temperature
(See the Installation Manual.)
Indicates the ventilation setting.
Current room temperature appears here.
Appears when the preset temperature range is restricted.
Most settings (except ON / OFF, mode, fan speed, temperature) can be made from the Menu screen.
OCH447B
8
Menu structure
Main menu
Press the MENU button.
Move the cursor to the desired item with the
F1
and
F2
buttons, and press the SELECT button.
Vane · Louver · Vent. (Lossnay)
High power
Timer
On / Off timer
Auto-Off timer
Filter information
Error information
Weekly timer
Energy saving
Auto return
Schedule
Night setback
Restriction
Temp. range
Operation lock
Maintenance
Auto descending panel
Manual vane angle
Initial setting
Main / Sub
Clock
Main display
Contrast
Display details
Auto mode
Administrator password
Language selection
Service
Service menu
Test run
Drain pump test run
Input maintenance info.
Function setting
Lossnay (City Multi only)
Check
Self check
Maintenance password
Remote controller check
Not all functions are available on all models of indoor units.
OCH447B
9
Main menu list
Setting and display items
Setting details
Vane · Louver · Vent.
(Lossnay)
Use to set the vane angle.
• Select a desired vane setting from f ve different settings.
Use to turn ON / OFF the louver.
• Select a desired setting from "ON" and "OFF."
Use to set the amount of ventilation.
• Select a desired setting from "Off," "Low," and "High."
High power
Use to reach the comfortable room temperature quickly.
• Units can be operated in the High-power mode for up to 30 minutes.
Timer
On/Off timer
Use to set the operation On/Off times.
• Time can be set in 5-minute increments.
* Clock setting is required.
Auto-Off
timer
Use to set the Auto-Off time.
• Time can be set to a value from 30 to 240 in 10-minute increments.
Filter information
Use to check the f lter status.
• The f lter sign can be reset.
Error information
Use to check error information when an error occurs.
• Error code, error source, refrigerant address, unit model, manufacturing number, contact
information (dealer's phone number) can be displayed.
* The unit model, manufacturing number, and contact information need to be registered in
advance to be displayed.
Weekly timer
Use to set the weekly operation On / Off times.
• Up to eight operation patterns can be set for each day.
* Clock setting is required.
* Not valid when the On/Off timer is enabled.
Energy
saving
Auto return
Use to get the units to operate at the preset temperature after performing energy-save
operation for a specif ed time period.
• Time can be set to a value from 30 and 120 in 10-minute increments.
* This function will not be valid when the preset temperature ranges are restricted.
Schedule
Set the start/stop times to operate the units in the energy-save mode for each day of the
week, and set the energy-saving rate.
• Up to four energy-save operation patterns can be set for each day.
• Time can be set in 5-minute increments.
• Energy-saving rate can be set to a value from 0% or 50 to 90% in 10% increments.
* Clock setting is required.
Night setback
Restriction
Use to make Night setback settings.
• Select "Yes" to enable the setting, and "No" to disable the setting. The temperature range and
the start/stop times can be set.
* Clock setting is required.
Temp. range
Use to restrict the preset temperature range.
• Different temperature ranges can be set for different operation modes.
Operation
lock
Use to lock selected functions.
• The locked functions cannot be operated.
Maintenance Auto
descending
panel
Manual
vane angle
Initial setting Main/Sub
Clock
Auto descending panel (Optional parts) Up / Down you can do.
Use to set the vane angle for each vane to a f xed position.
When connecting two remote controllers, one of them needs to be designated as a sub
controller.
Use to set the current time.
Main display Use to switch between "Full" and "Basic" modes for the Main display.
• The default setting is "Full."
Contrast
OCH447B
Use to adjust screen contrast.
10
Setting and display items
Initial setting Display
details
Auto mode
Setting details
Make the settings for the remote controller related items as necessary.
Clock: The factory settings are "Yes" and "24h" format.
Temperature: Set either Celsius (°C) or Fahrenheit (°F).
Room temp. : Set Show or Hide.
Auto mode: Set the Auto mode display or Only Auto display.
Whether or not to use the AUTO mode can be selected by using the button.
This setting is valid only when indoor units with the AUTO mode function are connected.
Administrator The administrator password is required to make the settings for the following items.
password
• Timer setting • Energy-save setting • Weekly timer setting
• Restriction setting • Outdoor unit silent mode setting • Night set back
Service
Language
selection
Test run
Use to select the desired language.
Select "Test run" from the Service menu to bring up the Test run menu.
• Test run • Drain pump test run
Input
Select "Input maintenance Info." from the Service menu to bring up the Maintenance
maintenance information screen.
The following settings can be made from the Maintenance Information screen.
• Model name input • Serial No. input • Dealer information input
Function
Make the settings for the indoor unit functions via the remote controller as necessary.
setting
This setting is required only when the operation of City Multi units is interlocked with
LOSSNAY
LOSSNAY units.
setting
(City Multi only)
Check
Error history: Display the error history and execute delete error history.
Refrigerant leak check: Refrigerant leaks can be judged.
Smooth maintenance: The indoor and outdoor maintenance data can be displayed.
Request cord: Details of the operation data including each thermistor temperature and error
history can be checked.
Self check
Error history of each unit can be checked via the remote controller.
Maintenance Take the following steps to change the maintenance password.
password
Remote
When the remote controller does not work properly, use the remote controller checking
controller
function to troublushoot the problem.
check
OCH447B
11
3-3. WIRED REMOTE CONTROLLER <PAR-21MAA>
“Sensor” indication
Display Section
For purposes of this explanation,
all parts of the display are shown.
During actual operation, only
the relevant items will be lit.
Identifies the current operation
Displays when the remote controller
sensor is used.
Day-of-Week
Shows the current day of the week.
Time/Timer Display
“Locked” indicator
Shows the current time, unless the simple or Auto Off
timer is set.
If the simple or Auto Off timer is set, the time to be
switched off is shown.
Indicates that remote controller buttons have been locked.
“Clean The Filter” indicator
Shows the operating mode, etc.
*Multilanguage display is available.
To be displayed on when it is time to
clean the filter.
TIME SUN MON TUE WED THU FRI SAT
TIMER
Hr
ON
AFTER
Indicates that operation from the
remote controller has been prohibited by a master controller.
“Timer is Off” indicator
Indicates that the timer is off.
WEEKLY
SIMPLE
AUTO OFF
ONLY1Hr.
Shows the target temperature.
The indicator comes on if the corresponding timer is set.
Fan Speed indicator
Shows the selected fan speed.
Up/Down Air Direction indicator
The indicator shows the direction of the outcoming airflow.
“One Hour Only” indicator
Temperature Setting
FUNCTION
FILTER
°F°C
°F°C
“Centrally Controlled” indicator
Timer indicators
AFTER OFF
ERROR CODE
Displays if the airflow is set to
Low or downward during COOL
or DRY mode. (Operation varies
according to model.)
The indicator goes off in one hour,
at which time the airflow direction
also changes.
Room Temperature display
Shows the room temperature. The room
temperature display range is 8 - 39.
The display blinks if the temperature
is less than 8 or 39 or more.
Ventilation indicator
Appears when the unit is running in
Ventilation mode.
Louver display
Indicates the action of the swing louver.
Does not appear if the louver is not
running.
(Power On indicator)
Indicates that the power is on.
Operation Section
ON/OFF button
Temperature setting buttons
Down
Fan Speed button
Up
Timer Menu button
(Monitor/Set button)
Filter
button
(<Enter> button)
Mode button (Return button)
TEMP.
ON/OFF
Set Time buttons
Check button (Clear button)
Back
Ahead
Timer On/Off button
(Set Day button)
Test Run button
MENU
BACK
PAR-21MAA
MONITOR/SET
ON/OFF
FILTER
DAY
CHECK TEST
OPERATION
CLOCK
CLEAR
Airflow Up/Down button
Louver button
(
Operation button)
To return operation
number
Opening the
cover
Built-in temperature sensor
Ventilation button
( Operation button)
To go to next operation
number
Note:
● “PLEASE WAIT” message
This message is displayed for approximately 3 minutes when power is supplied to the indoor unit or when the unit is recovering from a power failure.
● “NOT AVAILABLE” message
This message is displayed if an invalid button is pressed (to operate a function that the indoor unit does not have).
If a single remote controller is used to operate multiple indoor units simultaneously that are different types, this message will not be displayed as
far as any of the indoor units is equipped with the function.
OCH447B
12
3-4. Wireless remote controller
CHECK TEST RUN display
CHECK and TEST RUN display indicate that
the unit is being checked or test-run.
MODEL SELECT display
Blinks when model is selected.
display
Lights up while the signal is transmitted to
the indoor unit when the button is pressed.
display
SET TEMP. display indicates the set desired
temperature.
CLOCK display
display
Displays the current time.
OPERATION MODE display
Operation mode display indicates which
operation mode is in effect.
TIMER display
CHECK TEST RUN
MODEL SELECT
°C
AMPM
AMPM
display
The vertical direction of air flow is indicated.
NOT AVAILABLE
ON/OFF
FAN SPEED SELECT button
Used to change the fan speed.
MODE SELECT button
”“
” display
Displays the order of timer operation.
”“
” display
Displays whether timer is on or off.
display
The unit is turned ON and OFF alternately
each time the button is pressed.
“
“
TEMP
buttons
FAN SPEED display indicates which fan
speed has been selected.
ON/OFF button
Displays when in timer operation or when
setting timer.
MODE
FAN
AUTO STOP
VANE
AUTO START
CHECK LOUVER
TEST RUN
SET
h
min
RESET
Used to switch the operation mode between
cooling, drying, fan, heating and auto mode.
SET TEMPERATURE button sets any desired
room temperature.
TIMER CONTROL buttons
AUTO STOP (OFF timer): when this switch is
set, the air conditioner will be automatically
stopped at the preset time.
AUTO START (ON timer): when this switch is
set, the air conditioner will be automatically
started at the preset time.
CLOCK
h and min buttons
Buttons used to set the “hour and minute” of
the current time and timer settings.
* If the outdoor unit is cool only type, the
heating and auto mode are not available.
LOUVER button
Changes left/right airflow direction.
CHECK-TEST RUN buttons
(Not available for this model.)
Only press this button to perform an
inspection check or test operation.
Do not use it for normal operation.
CLOCK button
RESET button
VANE CONTROL button
SET button
Used to change the air flow direction.
OCH447B
13
4
SPECIFICATION
4-1. Specif cations
Model
PKFY-P100VKM-E
PKFY-P63VKM-E
1-phase 220-240V 50Hz, 1-phase 220V 60Hz
Power source
Cooling capacity
(Nominal)
*1
*1
*1
*2
Power input *4
Current input *4
Heating capacity
(Nominal)
*3
*3
*3
Power input
Current input
External finish
External dimension H × W × D
Net weight
Heat exchanger
Fan
Type x Quantity
External
static press.
Motor type
Motor output
Driving mechanism
Airflow rate
(Low-High)
7.1
6,100
24,200
6,300
0.05
0.37
8.0
6,900
27,300
0.04
0.30
kW
kcal/h
Btu/h
kcal/h
kW
A
kW
kcal/h
Btu/h
kW
A
Plastic, MUNSELL (1.0Y 9.2/0.2)
365 × 1170 × 295
14-3/8" × 46-1/16" × 11-5/8"
21 (46)
Cross fin (Aluminum fin and copper tube)
Line flow fan × 1
0
0
DC motor
0.056
Direct-drive
mm
in.
kg (lb)
Pa
mmH2O
kW
m3/min
L/s
cfm
dB <A>
Noise level (Low-High)
(measured in anechoic room)
Insulation material
Air filter
Protection device
Refrigerant control device
Connectable outdoor unit
Liquid
Diameter of
(R410A) mm (in.)
refrigerant pipe
Gas
(R410A) mm (in.)
Field drain pipe size
Document
Standard
Accessory
attachment
Drain pump kit
Optional parts
Remark
*1 Nominal cooling conditions
Indoor :
Outdoor :
Pipe length :
Level difference :
16 - 20
267 - 333
565 - 706
20 - 26
333 - 433
706 - 918
39 - 45
41 - 49
ø9.52 (ø3/8")
ø9.52 (ø3/8")
ø15.88 (ø5/8")
ø15.88 (ø5/8")
Flare
Flare
Flare
Flare
mm (in.)
Installation
Note :
11.2
9,600
38,200
10,000
0.08
0.58
12.5
10,800
42,600
0.07
0.51
Flare
Flare
Flare
Flare
Installation Manual, Instruction Book
PAC-SH94DM-E
Details on foundation work, insulation work, electrical wiring, power source switch, and other items shall be referred to the
Installation Manual.
Unit converter
*3 Nominal heating conditions
*2 Nominal cooling conditions
27°CDB/19°CWB (81°FDB/66°FWB)
35°CDB (95°FDB)
7.5 m (24-9/16 ft)
0 m (0 ft)
27°CDB/19.5°CWB (81°FDB/67°FWB)
35°CDB (95°FDB)
5 m (16-3/8 ft)
0 m (0 ft)
*4 Electrical characteristic of cooling are included optional drain - pump.
* Nominal conditions *1, *3 are subject to JIS B8615-1.
* Due to continuing improvement, above specification may be subject to change without notice.
OCH447B
Polyethylene sheet
PP honeycomb
Fuse
LEV
R410A, R407C, R22 CITY MULTI
ø9.52 (ø3/8")
ø9.52 (ø3/8")
ø15.88 (ø5/8")
ø19.05 (ø5/8")
I.D. 16mm (5/8")
14
20°CDB (68°FDB)
7°CDB/6°CWB (45°FDB/43°FWB)
7.5 m (24-9/16 ft)
0 m (0 ft)
kcal/h = kW × 860
Btu/h = kW × 3,412
cfm = m3/min × 35.31
lb = kg/0.4536
*Above specification data is
subject to rounding variation.
4-2. Electrical parts specif cations
Service Ref.
Parts name
PKFY-P63VKM-E.TH
PKFY-P63VKM-ER1.TH
Symbol
PKFY-P100VKM-E.TH
PKFY-P100VKM-ER1.TH
Room temperature
thermistor
TH21
Resistance 0/15k, 10/9.6k, 20/6.3k, 25/5.4k, 30/4.3k, 40/3.0k
Liquid pipe thermistor
TH22
Resistance 0/15k, 10/9.6k, 20/6.3k, 25/5.4k, 30/4.3k, 40/3.0k
Gas pipe thermistor
TH23
TH24
Resistance 0/15k, 10/9.6k, 20/6.3k, 25/5.4k, 30/4.3k, 40/3.0k
Fuse
(Indoor controller board)
FUSE
250V 3.15A
Fan motor
MF
8-Pole Output 56W / RCOJ56-AC
Vane motor
MV
MSBPC20 DC12V
Linear expansion valve
LEV
Power supply terminal
block
TB2
(L, N, ) 250V 20A
Transmission terminal
block
TB5
(M1, M2, S) 250V 20A
MA remote controller
terminal block
TB15
(1, 2) 250V 10A
EFM-40YGME
DC 12 V
EFM-80YGME
DC 12 V
4-3. Sound levels
Sound level at anechoic room : Low-High
Sound level dB (A)
1.0m
PKFY-P63VKM-E.TH
PKFY-P63VKM-ER1.TH
PKFY-P100VKM-E.TH
PKFY-P100VKM-ER1.TH
1.0m
Measurement location
* Measured in anechoic room.
4-4. NC curves
PKFY-P63VKM-E.TH
PKFY-P63VKM-ER1.TH
External static pressure : 0Pa
Power source : 220, 230, 240V, 50Hz/220V, 60Hz
70.0
High
Low
65.0
60.0
NC-60
55.0
50.0
NC-50
45.0
40.0
NC-40
35.0
30.0
NC-30
25.0
20.0
15.0
10.0
63
Approximate minimum
audible limit on
continuous noise
125
250
NC-20
500
1k
2k
Octave band center frequencies (Hz)
OCH447B
4k
8k
Octave band pressure level (dB) 0dB=20μPa
Octave band pressure level (dB) 0dB=20μPa
70.0
PKFY-P100VKM-E.TH
PKFY-P100VKM-ER1.TH
External static pressure : 0Pa
Power source : 220, 230, 240V, 50Hz/220V, 60Hz
High
Low
65.0
60.0
NC-60
55.0
50.0
NC-50
45.0
40.0
NC-40
35.0
30.0
NC-30
25.0
20.0
15.0
10.0
63
Approximate minimum
audible limit on
continuous noise
125
250
NC-20
500
1k
2k
Octave band center frequencies (Hz)
15
4k
8k
39 - 45
41 - 49
5
OUTLINES AND DIMENSIONS
PKFY-P63VKM-E.TH
PKFY-P63VKM-ER1.TH
PKYF-P100VKM-E.TH
PKFY-P100VKM-ER1.TH
Unit : mm
Top side
431.7
11
140.3
65.2
423.7
Left side
Right side
Front side
Mount board
365
Knockout hole
for left piping
C
74
A
(855)
295
241
5
Operation lamp
DEFROST/STAND BY lamp
1170
Receiver
Knockout hole for
right piping
Front side (Grille open)
Terminal block for power supply
Terminal block for transmission
Terminal block for
MA-remote controller
Emergency operation switch
(cooling / heating)
30
35
444 (Gas pipe)
66
123
154
482 (Liquid pipe)
585 (Drain hose)
134
Under side
Piping connection department
Refrigerant pipe : 9.52
Flared connection : 3/8F
Gas pipe
Refrigerant pipe : 15.88
Flared connection : 5/8F
Louver (manual)
C
B
3
364
384.5
408.5
439
454
465.5
Mount board
10
0
10
60
110
314
Temporarily fixing hole
Indoor unit outline
54
32
25
0
0
37.5
62.5
50
75
100
117
125
142
192
67
77
87
7.8
77
7.8
65
67
25
77
Center measurement hole Φ2.5
A
15.5
10.7
454
439
408.5
384
364
75-Φ5.1
Tapping screw hole
517.4
4-Φ9 Bolt hole
Knockout hole for piping
O.D
B
Knockout hole
for lower piping
314
Vane (auto)
0
B
54
75~ 80
65
16
Drain hose
Sleeve
Through hole
(purchased locally)
75
Liquid pipe
60
110
32
18
53
Filter hook
65
104.5
129.5
167
217
242
279.5
292
Wall hole for
left rear piping
Min. 48
Air inlet
Air outlet
Min. 52.3
Min. 220
550 mm or greater with optional
drain pump installation
OCH447B
Min. 100.5
108 mm or greater with left or
rear left piping or drain pump installation
Min. 250
Min. 7
265 mm or greater with optional
drain pump installation
Required space (Indoor unit)
16
Wall hole for
right rear piping
585
439
449.2
339
349.2
384
Knockout hole for
left rear piping
(75×480)
216.5
0
189
339
384
439
430.5
585
530.5
7.5
R3
264
292
308.5
311
12.5
12.5
87.5
229.5
6
WIRING DIAGRAM
PKFY-P63VKM-E.TH
SYMBOL
I.B
CN32
CN51
CN52
BZ
DSA
FUSE
LED1
LED2
SW2
SW3
SW4
SWE
X1
MOV 01.02
LEV
MF
MV
TB2
TB5
TB15
1
3
6 1
FAN
CNMF
(WHT)
TB2
RED
L
BLU
N
GRN/YLW
DP
M
1~
FUSE BREAKER
(16A)
PULL (16A)
BOX
POWER SUPPLY
~/N220-240V 50Hz
220V 60Hz
3
6
TO NEXT MV
INDOOR
UNIT
M
LD SWE(B)
LEV
LED2 LD101(B)
M
5
FUSE
CNP
3 (BLU)
X1
DSA
MOV2
MOV1
LED1
U
3
1
LDSWE(A)
(BLU)
5 VANE 1
CN151
(WHT)
5
BRN
RED
BLU
ORN
YLW
WHT
1
6
6 CNRU 1
(WHT)
1
LEV
CN60
(YLW)
DC311~339V
RECTIFICATION
3
ADDRESS
CN81
(RED)
8
1
1
LED2
12345678
5 CN51 1
(WHT)
CN24
(YLW)
2 1
LIQUID/GAS1
CN44
(WHT)
ADDRESS 4
1
CN42
4 (RED) 1 INTAKE
CN20
(RED) 2 1
1
TH24
t○
TH23
t○
TH22
t○
TH21
t○
TB15
1
TO MA-REMOTE
CONTROLLER
DC8.7-13V
2
M1
M2
S
(SHIELD)
TB5
When attaching drain pump
(option)
FLOAT SW
CN4F
(WHT)
FS
Models
P63
1
4
SW2
ON
OFF
ON
P100 OFF
123456
123456
The black square (■) indicates
a switch position.
4
8
3
See fig.+1
S.B
<fig:1>
1
GAS2
CN2G
(BLK) 2 1
SWE1 SWE2
LED1
When attaching drain
pump(option), remove
the jumper connector
CN4F and fit the drain
float switch (FS).
MA-REMOCON
CN3A
(BLU)
ORN
SW3
ORN
BLU
M-NET
SW4
SW2
CN2M(BLU) ON
OFF
1
2
123456 1234
1
W.B
CN52
(GRN)
FLOAT SW
CN4F
(WHT) 4
BZ
CN32
(WHT)
BLU
RU
I.B
CND
(BLK)
GRN
YLW
ORN
RED
BRN
BLK
WHT
YLW
BLU
RED
MS
3~
NAME
NAME
SYMBOL
INDOOR CONTROLLER BOARD
TH21
THERMISTOR ROOM TEMP. DETECTION
(0°C/15kΩ, 25°C/5.4kΩ)
CONNECTOR REMOTE SWITCH
CENTRALLY CONTROL
TH22
PIPE TEMP. DETECTION/LIQUID
(0°C/15kΩ, 25°C/5.4kΩ)
REMOTE INDICATION
BUZZER
TH23
PIPE TEMP. DETECTION/GAS1
(0°C/15kΩ, 25°C/5.4kΩ)
SURGE ABSORBER
FUSE (T3.15AL 250V)
TH24
PIPE TEMP. DETECTION/GAS2
(0°C/15kΩ, 25°C/5.4kΩ)
POWER SUPPLY (I.B)
POWER SUPPLY (I.B)
ADDRESS BOARD
A.B
SWITCH CAPACITY CODE
SWA SWITCH
FAN SPEED SELECTOR
MODE SELECTION
SW1
MODE SELECTION
MODEL SELECTOR
SW11
ADDRESS SETTING 1s DIGIT
DRAIN PUMP (TEST MODE)
ADDRESS SETTING 10ths DIGIT
SW12
AUX.RELAY DRAIN PUMP (OPTION)
SW14
BRANCH No.
VARISTOR
S.B
SWITCH BOARD
SWE1 EMERGENCY OPERATION (HEAT)
LINEAR EXPANSION VALVE
FAN MOTOR
SWE2 EMERGENCY OPERATION (COOL)
VANE MOTOR
W.B
PCB FOR WIRELESS REMOTE CONTROLLER
TERMINAL POWER SUPPLY
LED1 LED (OPERATION INDICATOR: GREEN)
TRANSMISSION
LED2 LED (OPERATION FOR HEATING: ORANGE )
BLOCK
MA-REMOTE CONTROLLER
RU
RECEIVING UNIT
DRAIN PUMP (OPTION)
DP
DRAIN FLOAT SWITCH (OPTION)
FS
RED
BLU
BLK
MF
PKYF-P100VKM-E.TH
TO OUTDOOR UNIT
BC CONTROLLER
REMOTE CONTROLLER
DC24-30V
ADDRESS
CN43
(RED)
SW1
ON
OFF
1 2 3 4 5 6 7 8 9 10
SW12
3
2
1
SWA
SW11
10ths
DIGIT
1s
DIGIT
ADDRESS
CN82
(RED)
SW14
BRANCH
No.
A.B
LED on indoor board for service
Mark
Meaning
LED1
Main power supply
LED2
Power supply for
MA-Remote controller
Function
Main power supply (Indoor unit:220-240V)
Power on → Iamp is lit
Power supply for MA-Remote controller
on → Iamp is lit
NOTES:
1. At servicing for outdoor unit, always follow the wiring diagram of outdoor unit.
2. In case of using MA-Remote controller, please connect to TB15.
(Remote controller wire is non-polar.)
3. In case of using M-NET, please connect to TB5. (Transmission line is non-polar.)
4. Symbol [S] of TB5 is the shield wire connection.
5. Symbols used in wiring diagram above are,
: terminal block,
:connecter.
6. The setting of the SW2 dip switches differs in the capacity. For the detail, refer to fig.1.
OCH447B
17
PKYF-P63VKM-ER1.TH
3
6
LD SWE(B)
LEV
LED2
RED
BLU
BLK
M
I.B
X1
LED1
5 VANE 1 6
CN151
(WHT)
BZ1
CNRU
(WHT)
6
1
3
Pair
No.
8
J41
J42
ADDRESS
CN81
(RED)
LIQUID/GAS1
CN44
(WHT)
ADDRESS
4
1
CN42
4 (RED) 1 INTAKE
CN20
(RED) 2 1
1
1
LED2
See fig:+1
SW3
12345678
1
When attaching drain pump
(option)
FS
8
1
4
The black square(■) indicates a
switch position.<+1>
Models
SW2
TH24
tº
TH23
tº
FLOAT SW
CN4F
(WHT)
TH22
P63
ON
OFF
P100
ON
OFF
tº
TH21
IT terminal
PAC-IT52AD-E
1
5
IT terminal
PAC-IT51AD-E
1
5
tº
5 4
1
CN100(WHT)
5 3
1
123456
123456
4
3
ON
OFF
TB15
1
2
0 1
9 0 1
10ths
DIGIT
1s
DIGIT
E
F0 1 2
3456
9
TO OUTDOOR UNIT
BC CONTROLLER
REMOTE CONTROLLER
DC24-30V
2 3
M1
M2
S
(SHIELD)
TB5
3
2
ADDRESS
1
CN82
1 2 3 4 5 6 7 8 9 10 SWA
(RED)
SW12 SW11 SWC SW14
2 3
TO MA-REMOTE
CONTROLLER
DC8.7-13V
ADDRESS
CN43
(RED)
SW1
BRANCH
No.
A.B
NOTES:
1. At servicing for outdoor unit,always follow the wiring diagram
of outdoor unit.
2. In case of using MA-Remote controller, please connect
to TB15. (Remote controller wire is non-polar.)
3. In case of using M-NET, please connect to TB5.
(Transmission line is non-polar.)
4. Symbol [S]of TB5 is the shield wire connection.
5. Symbols used in wiring diagram above are,
: terminal block,
:connecter.
6.The setting of the SW2 dip switches differs in the capacity.
For the detail, refer to the fig:+1.
OCH447B
LED on indoor board for service
Mark
Meaning
LED1
Main power supply
LED2
Power supply for
MA-Remote controller
18
8
5 4
1
CN100(WHT)
5
1
CN52(GRN)
CN51(WHT)
In connecting optional IT terminal, use
either CN51 or CN52 which is not connected.
Be careful for connector colors.
8
MA-REMOCON
CN3A(BLU)
ORN
SW4
1234
ORN
BLU
BLU
M-NET
SW2
CN2M(BLU) ON
OFF
1
2
123456
+2
1
GAS2
CN2G
(BLK) 2 1
CN32
(WHT)
S.B
LED1
When attaching drain
pump(option), remove
the jumper connector
CN4F and fit the drain
float switch (FS).
CN24
(YLW) 2 1
CN100 +2
(WHT)
W.B
1
FLOAT SW
CN4F
(WHT) 4
1
OFF ON
5
1
CN51 +2
(WHT)
1
LEV
CN60
(YLW)
8
SWE
+
5
CN52 +2
(GRN)
7 8
FUSE
CNP
3 (BLU)
1
LDSWE(A)
(BLU)
SWE1 SWE2
7 8
3
BRN
RED
BLU
ORN
YLW
WHT
5
CND
(BLK)
LD101(B)
RU
BCD
TO NEXT MV
INDOOR
M
UNIT
GRN
YLW
ORN
RED
BRN
BLK
WHT
YLW
BLU
RED
1
3 FAN 6 1
CNMF
(WHT)
POWER SUPPLY
~/N220-240V 50Hz
220V 60Hz
5 6
M
1~
FUSE BREAKER
PULL (16A)
(16A)
BOX
4
DP
MS
3~
1
TB2
RED
L
BLU
N
GRN/YLW
4 5 6
MF
NAME
NAME
SYMBOL
INDOOR CONTROLLER BOARD
TH21
THERMISTOR ROOM TEMP. DETECTION
(0ºC/15kΩ, 25ºC/5.4kΩ)
CONNECTOR REMOTE SWITCH
CENTRALLY CONTROL
PIPE TEMP. DETECTION / LIQUID
TH22
(0ºC/15kΩ, 25ºC/5.4kΩ)
REMOTE INDICATION
IT TERMINAL
PIPE TEMP. DETECTION / GAS1
TH23
(0ºC/15kΩ,25ºC/5.4kΩ)
BUZZER
FUSE (T3.15AL 250V)
TH24
PIPE TEMP. DETECTION / GAS2
(0ºC/15kΩ, 25ºC/5.4kΩ)
POWER SUPPLY(I.B)
POWER SUPPLY(I.B)
ADDRESS BOARD
A.B
SWITCH CAPACITY CODE
SWA SWITCH
FAN SPEED SELECTOR
MODE SELECTION
SW1
MODE SELECTION
MODEL SELECTOR
SW11
ADDRESS SETTING 1s DIGIT
DRAIN PUMP(TEST MODE)
SW12
ADDRESS SETTING 10ths DIGIT
AUX.RELAY DRAIN PUMP(OPTION)
SW14
BRANCH No.
LINEAR EXPANSION VALVE
S.B
SWITCH BOARD
SWE1 EMERGENCY OPERATION(HEAT)
FAN MOTOR
SWE2 EMERGENCY OPERATION(COOL)
VANE MOTOR
TERMINAL POWER SUPPLY
W.B
PCB FOR WIRELESS REMOTE CONTROLLER
TRANSMISSION
LED1 LED(OPERATION INDICATOR:GREEN)
BLOCK
MA-REMOTE CONTROLLER
LED2 LED(PREPARATION FOR HEATING : ORANGE)
RU
RECEIVING UNIT
DRAIN PUMP (OPTION)
DP
DRAIN FLOAT SWITCH (OPTION)
FS
789A
SYMBOL
I.B
CN32
CN51
CN52
CN100
BZ1
FUSE
LED1
LED2
SW2
SW3
SW4
SWE
X1
LEV
MF
MV
TB2
TB5
TB15
PKFY-P100VKM-ER1.TH
Function
Main power supply (Indoor unit:220-240V)
Power on → Iamp is lit
Power supply for MA-Remote controller
on → Iamp is lit
7
REFRIGERANT SYSTEM DIAGRAM
PKFY-P63VKM-E.TH
PKFY-P63VKM-ER1.TH
PKYF-P100VKM-E.TH
PKFY-P100VKM-ER1.TH
Gas pipe thermistor (1) TH23
Strainer (#50mesh)
Gas pipe
Gas pipe thermistor (2) TH24
Flare connection
Liquid pipe thermistor TH22
Heat exchanger
Liquid pipe
Linear expansion valve
Strainer1 (#50mesh)
Strainer2 (#100mesh)
Strainer (#100mesh)
Room temparature thermistor TH21
Unit : mm (inch)
Item
8
Model
PKFY-P63VKM-E
PKFY-P100VKM-E
Gas pipe
:15.88 (5/8)
:15.88 (5/8)
Liquid pipe
:9.52 (3/8)
:9.52 (3/8)
TROUBLESHOOTING
8-1. HOW TO CHECK THE PARTS
PKFY-P63VKM-E.TH
PKYF-P100VKM-E.TH
PKFY-P63VKM-ER1.TH
PKFY-P100VKM-ER1.TH
Parts name
Check points
Room temperature
thermistor (TH21)
Liquid pipe temperature
thermistor (TH22)
Gas pipe temperature
thermistor (TH23 ,24)
Vane motor (MV)
Red
Abnormal
4.3k~9.6k
Open or short
Orange Green
Abnormal
-
-
-
-
Brown-Red Brown-Orange Brown-Yellow Brown-Green
Open or short
Yellow
Orange
Blue
Red
Brown
OCH447B
250 ± 7%
Refer to 8-1-3.
Linear expansion
valve (LEV)
CN60
White
Refer to the next page for the details.
Normal
M
Fan motor (MF)
LEV
Normal
Measure the resistance between the terminals with a tester. (Coil temperature 20)
Yellow
Brown
Connect pin No.
Disconnect the connector then measure the resistance with a tester.
(At the ambient temperature 10 - 30)
1
2
3
4
5
6
Disconnect the connector then measure the resistance valve with a tester.
(Coil temperature 20)
Normal
Abnormal
(1)-(5)
(2)-(6)
(3)-(5)
(4)-(6)
White-Red Yellow-Brown Orange-Red Blue-Brown
Open or short
200 ± 10%
19
8-1-1. Thermistor
<Thermistor Characteristic graph>
Thermistor for
lower temperature
< Thermistor for lower temperature >
0:
10:
20:
25:
30:
40:
1
273+t
40
Resistance (K)
Thermistor R0=15k" ± 3%
Fixed number of B=3480 ± 2%
Rt=15exp { 3480(
50
Room temperature thermistor (TH21)
Liquid pipe temperature thermistor (TH22)
Gas pipe temperature thermistor (TH23)
(TH24)
1
)}
273
15k"
9.6k"
6.3k"
5.4k"
4.3k"
3.0k"
30
20
10
0
-20
-10
0
10 20 30
Temperature ()
40
50
8-1-2. Liner expansion valve
1 Operation summary of the linear expansion valve
• Linear expansion valve opens/closes through stepping motor after receiving the pulse signal from the indoor controller board.
• Valve position can be changed in proportion to the number of pulse signal.
<Connection between the indoor controller board and the linear expansion valve>
Controller board
DC12V
Linear expansion valve
Brown
6
Red
5
4
Blue
M
Brown
:4
Blue
4
:4
6
Yellow
Orange
3
:3
2
:3
5
:2
Yellow
2
:2
:1
White
1
:1
1
White Red
3
Orange
Drive circuit
Connector(CN60)
Note : Since the number of the connector at the controller board side and the relay connector are different, follow the color of
the lead wire.
OCH447B
20
<Output pulse signal and the valve operation>
Output
Output
(Phase)
1
2
3
4
{1
ON
OFF
OFF
ON
{2
ON
ON
OFF
OFF
{3
OFF
ON
ON
OFF
{4
OFF
OFF
ON
ON
2 Linear expansion valve operation
Open
C
Valve position (capacity)
D
Close
Open
A
E
Close
Closing a valve : 1 → 2 → 3 → 4 → 1
Opening a valve : 4 → 3 → 2 → 1 → 4
The output pulse shifts in above order.
• When linear expansion valve operation stops, all output phase
become OFF.
• At phase interruption or when phase does not shift in order, motor
does not rotate smoothly and motor will lock and vibrate.
• When the switch is turned on, 2200 pulse closing valve signal will
be sent till it goes to point A in order to define the valve position.
• When the valve moves smoothly, there is no noise or vibration
occurring from the linear expansion valves : however, when the
pulse number moves from E to A or when the valve is locked,
more noise can be heard than in a normal situation.
• Noise can be detected by placing the ear against the screw driver
handle while putting the screw driver tip to the linear expansion
valve.
Outdoor unit R410A model
: 1400 pulse
Outdoor unit R22/R407C model : 2000 pulse
Opening a valve
all the way
Pulse number
B
Extra tightening (200~800 pulse)
3 Troubleshooting
Symptom
Check points
Countermeasures
Operation circuit
failure of the micro
processor
Disconnect the connector on the controller board, then con- Exchange the indoor controller board in case of
nect LED for checking.
6
5
drive circuit failure.
4
3
2
1
1k LED
When power is turned on, pulse signals will output for 10
seconds. There must be some defects in the operation circuit
if the LED does not light while the signals are output or keeps
lighting even after the signals stop.
Linear expansion
valve mechanism is
locked.
Exchange the linear expanMotor will idle and make a ticking noise when the motor is
operated while the linear expansion valve is locked. This tick- sion valve.
ing sound is the sign of the abnormality.
Short or breakage
Measure the resistance between each coil (white-red, yellow- Exchange the linear expanof the motor coil of
brown, orange-red, blue-brown) using a tester. It is normal if sion valve.
the linear expansion the resistance is in the range of 200 ±10%.
valve
Valve does not close To check the linear expansion valve, operate the indoor unit If large amount of refrigercompletely.
in fan mode and at the same time operate other indoor units ant is leaked, exchange
the linear expansion valve.
in cooling mode, then check the pipe temperature <liquid
pipe temperature> of the indoor unit by the
outdoor multi controller board operation
monitor. During fan operation, linear expansion valve is closed completely and if there
Thermistor
(Liquid pipe) is any leaking, detecting temperature of
the thermistor will go lower. If the detected
Linear
temperature is much lower than the temexpansion
valve
perature indicated in the remote controller,
it means the valve is not closed all the way.
It is not necessary to exchange the linear expansion valve, if
the leakage is small and not affecting normal operation.
Wrong connection
of the connector or
contact failure
OCH447B
Check the color of lead wire and missing terminal of the con- Disconnect the connector
nector.
at the controller board,
then check the continuity.
21
8-1-3. DC Fan motor (fan motor/indoor controller circuit board)
Check method of DC fan motor (fan motor/indoor controller circuit board)
Notes
· High voltage is applied to the connecter (CNMF) for the fan motor. Pay attention to the service.
· Do not pull out the connector (CNMF) for the motor with the power supply on.
(It causes trouble of the indoor controller circuit board and fan motor.)
Self check
Symptom : The indoor fan cannot turn around.
Wiring contact check
Contact of fan motor connector (CNMF)
Is there contact failure?
Wiring recovery
Yes
No
Power supply check (Remove the connector (CNMF))
Measure the voltage in the indoor controller circuit board.
TEST POINT : VDC (between 1 (+) and 3 (-) of the fan connector): VDC DC310~340V
TEST POINT : VCC (between 4 (+) and 3 (-) of the fan connector): VCC DC15V
Is the voltage normal?
No
Indoor controller board fuse check
Yes
No
Is the fuse normal?
Replace
the fuse.
Yes
Replace the indoor
controller board.
NG
Check the operation
OK
Check the operation
END
NG
Replace the fan motor.
Sensor signal check
Measure the voltage between CNMF and DC 0V
and DC 5V in the door controller circuit board.
No
Does the voltage repeat
DC 0V and DC 15V?
Replace the fan motor.
Yes
Yes
Check the operation of fan.
Replace the indoor
controller board.
NG
Replace the indoor controller board.
OK
Check the operation
END
NG
Replace the fan motor.
OCH447B
OK
22
END
OK
END
8-2. Function of Dip switch
PKFY-P63VKM-E.TH
PKYF-P100VKM-E.TH
PKFY-P63VKM-ER1.TH
PKFY-P100VKM-ER1.TH
Switch Pole
Operation by switch
Function
ON
OFF
1
Thermistor<Room temperature>
position
Built-in remote controller
Indoor unit
2
Filter clogging detection
Provided
Not provided
3
Filter cleaning sign
4
Fresh air intake
Address board
2,500 hr
100 hr
Not effective
Not effective
1 2 3 4 5 6 7 8 9 10
Fan operation at Heating mode Thermo ON operation at
heating mode
8
Air flow set in case of heat Low *1
thermo OFF
Setting air flow *1
Depends on SW1-7
9
Auto restart function
Effective
Not effective
Power ON/OFF by breaker Effective
Not effective
SW2
Capacity
1~6
code
switch
P63
ON
OFF
123456
ON
P100 OFF
123456
2
Not used
—
—
3
SW3 4
Function
selection 5
6
Not used
—
—
Second setting *1
First setting
Changing the opening of linear
expansion valve during thermo OFF
Effective
Not effective
Heating 4 degree up
Not effective
Effective
7
Target superheat setting *2
—
—
8
Target subcool
—
—
1 2 3 4
Indoor controller board
<Initial setting>
Set for each capacity
Indoor controller board
<Initial setting>
Under
suspension
Before
power
supply
ON
ON
OFF
1 2 3 4 5 6 7 8
*1 Second setting is same as
first setting.
*2 Please do not change SW3-7
and 3-8.
Indoor controller board
Address board
CDE
AB
F01
78
Before
power
supply
ON
90 1
Address board
<Initial setting>
SW14
F01
23
23
45 6
How to set branch numbers SW14 (Series R2 only)
Match the indoor unit’s refrigerant pipe with
the BC controller’s end connection number.
Remain other than series R2 at "0".
SW11
90 1
78
45 6
SW14
SW12
23
1
<Initial setting>
23
10
How to set addresses
Example : If address is "3", remain SW12
(for over 10) at "0", and match SW11 (for 1 to 9)
with "3".
CDE
AB
78
90 1
45 6
78
SW11
23
90 1
789
SW12
45 6
789
Rotary switch
OFF
23
OCH447B
ON
23
SW14
Branch
No.
Setting
Rotary switch
SW4
Model 1~4
Select
SW11
1s digit
address
setting
SW12
10ths digit
address
setting
Heat pump
Vane horizontal angle
SW1-7 SW1-8 Fan speed
OFF OFF Extra low
ON
OFF Low
OFF
ON Setting air flow
ON
ON Stop
*2 It is impossible to intake
the fresh air.
Before
power
supply
ON
Heat pump/Cool only
*2
Under
suspension
Extra low *1
1
Cooling only
NOTE:
*1
45 6
10
<Initial setting>
ON
OFF
Switching remote controller display Thermo ON signal indication Fan output indication
Humidifier control
Remarks
45 6
SW1
5
Mode
selection 6
7
*2
Effective
timing
Switch
Operation by switch
J41, J42
Jumper
Wireless
remote
controller
Pair No.
Effective
timing
• To operate each indoor unit by each remote controller when installed 2 indoor
units or more are near, Pair No. setting is necessary.
Pair No. setting is available with the 4 patterns (Setting patterns A to D).
.
Make setting for J41, J42 of indoor controller board and the Pair No. of
wireless remote controller.
• You may not set it when operating it by one remote controller.
Setting for indoor unit
Cut jumper wire J41, J42 on the indoor controller board according to the
table below.
Wireless remote controller pair number:
Setting operation
Under
1. Press the SET button (using a pointed implement). Check that the
operation
remote controller's display has stopped before continuing.
or
MODEL SELECT flashes, and the model No. (3 digits) appears (steadily-lit).
2. Press the MINUTE button twice. The pair number appears flashing.
suspension
3. Press the temperature
buttons to select the pair number to set.
4. Press the SET button (using a pointed implement). The set pair number is
displayed (steadily-lit) for 3 seconds, then disappears.
Setting pattern
Indoor controller
jumper wire
Pair No. of wireless
remote controller
J41
J42
A
—
—
0
Initial setting
B
Cut
—
1
—
C
—
Cut
2
—
D
Cut
Cut
3
—
* Pair No .4-9 of wireless remote controller is setting pattern D.
OCH447B
24
Remarks
<Initial setting>
Pattern A
Pair No.
MODEL SELECT
FAN
AUTO STOP
VANE
AUTO START
CHECK LOUVER
SET
h
min
TEST RUN
SET button
Temperature
button
TEMP
ON/OFF
MODE
Model No.
RESET
CLOCK
Minute
button
8-3. TEST POINT DIAGRAM
8-3-1. Indoor controller board
PKFY-P63VKM-E.TH
PKFY-P63VKM-ER1.TH
PKFY-P100VKM-E.TH
PKFY-P100VKM-ER1.TH
CNMF
CN2M
Connect to the terminal block
(TB5) (M-NET transmission
connecting wire)
24-30VDC (non-polar)
Power supply from outdoor unit
Connect to the fan motor (MF)
1-3 : DC310~340V
4-3 : DC15V
5-3 : DC0~6V
6-3 : DC0 or DC15V
CNP
Drain pump output
(DP)
1-3 : 220-240VAC
CND
Power supply for
indoor controller board
1-3 : 220-240VAC
FUSE
3.15A 250V
LED1
Main power supply
(Indoor unit :
220-240V)
CN151
Vane motor output
12VDC pluse
CNRU
Connect to the wireless remote controller
board (W.B)
LDSWE(A)
Connect to the
wireless remote
controller board (S.B)
SW2
Capacity setting
CN52
Remote indicator
1-2: Status lamp 12VDC (1 : +)
Fan motor output
(SW1-5 OFF)
Thermostat ON (SW1-5 ON)
1-3: Cooling/Dry status lamp
12VDC (1 : +)
1-4: Heating status lamp
12VDC (1 : +)
SW4
Model selection
SW3
Function setting
Jumper wire J41, J42
Pair No. setting for
wireless remote
controller
LED2
Power supply for
MA-Remote controller
CN3A
Connected to the termial
block (TB15)
(MA-Remote controller
connecting wire)
1 - 3 : 8.7-13V DC
(Pin1 (+))
CN32
Remote switch
CN2G
Pipe temperature
thermistor
Gas2 (TH24)
CN20
Room temperature
thermistor (TH21)
CN44
Pipe temperature thermistor
1-2 : Liquid (TH22)
3-4 : Gas1 (TH23)
The voltage range of DC12V in this
page is between DC11.5 V to DC 13.7 V.
OCH447B
25
CN4F
Drain float
switch (FS)
CN60
Liner expansion
valve (LEV) output
12VDC pluse output
CN51
Centrally control
1-2 : Control signal
12VDC pulse input (1 : +)
3-4 : Operation indicator
12VDC (3 : +)
3-5 : Malfunction indicator
12VDC (3 : +)
LD SWE (B)
Connect to the
indoor controller
board (I.B)
8-3-2. Wireless remote controller board
PKFY-P63VKM-E.TH
PKFY-P63VKM-ER1.TH
PKFY-P100VKM-E.TH
PKFY-P100VKM-ER1.TH
LD101
Connect to the
indoor controller
board (I.B)
8-3-3. Address board
PKFY-P63VKM-E.TH
PKFY-P63VKM-ER1.TH
PKFY-P100VKM-E.TH
PKFY-P100VKM-ER1.TH
SW1
Function setting
SW12
Address setting
10ths DIGIT
OCH447B
SW11
SW14
Address setting
1s DIGIT
Branch No.
26
9
DISASSEMBLY PROCEDURE
PKFY-P63VKM-E.TH
PKFY-P63VKM-ER1.TH
PKFY-P100VKM-E.TH
PKFY-P100VKM-ER1.TH
OPERATION PROCEDURE
Be careful when removing heavy parts.
PHOTOS & ILLUSTRATIONS
1. REMOVING THE PANEL
Photo 1
Screws
Front grille
(1) Press and unlock the knobs on both sides of the front grille
and lift the front grille until it is level. Pull the hinges forward
to remove the front grille. (See Photo 1)
(2) Remove 3 screw caps of the panel. Remove 5 screws.
(See Photo 1)
(3) Unfix 3 hooks. (See Figure 1)
(4) Hold the lower part of both ends of the panel and pull it
slightly toward you, and then remove the panel by pushing
it upward.
(5) Remove the screw of the corner box. (See Photo 1)
Remove the corner box.
Screws and screw caps
Figure 1
2. REMOVING THE ADDRESS BOARD, THE INDOOR
CONTROLLER BOARD, THE WIRELESS
CONTROLLER BOARD
(1) Remove the panel and the corner box. (Refer to
procedure 1)
(2) Remove the screw and hook of address board case. (See
Photo 2)
(3) Disconnect the connectors of address board.
(4) Remove the front and side electrical box covers (each 1
screw).
(5) Disconnect the connectors on the indoor controller board.
(See Photo 3)
(6) Remove the switch board holder and open the cover.
(7) Pull out the indoor controller board toward you then
remove the indoor controller board and switch board. (See
Photo 3)
(8) Remove the holder of wireless remote controller board.
(9) Disconnect the connector of wireless remote controller
board and remove the wireless remote controller board
from the holder.
Screw of the
corner box
Hooks
Photo 2
Screw of address
board case
Hook
Screw of
electrical box
cover (side)
Switch board
holder
Water cut
Screw of electrical box cover
(Front)
Photo 3
Holder of wireless
remote controller board
Electrical box cover
(Front)
Indoor controller board
Terminal block (TB2)
Terminal block (TB5)
Terminal block (TB15)
Room temp. thermistor (TH21)
OCH447B
27
OPERATION PROCEDURE
PHOTOS
3. REMOVING THE ELECTRICAL BOX
Photo 4
Connect for ground
(1) Remove the panel and the corner box. (Refer procedure to 1)
(2) Remove the screw and hook of address board case.
(3) Remove the front and side electrical box covers (each 1
screw).
(4) Remove the transmission wiring of TB5, the power supply
wiring of TB2 and the wiring of MA-remote controller (TB15).
(5) Disconnect the connectors on the indoor controller board.
(6) Disconnect the connector for ground wire.
(7) Remove the screw on lower side of the electrical box.
(See Photo 5)
(8) Push up the upper fixture catch to remove the box, then
remove it from the box fixture.
Fixture
Electrical box
4. REMOVING THE NOZZLE ASSEMBLY (with VANE
and VANE MOTOR) AND DRAIN HOSE
Photo 5
(see the bottom)
Nozzle assembly
Vane motor
(1) Remove the panel and corner box. (Refer to procedure 1)
(2) Remove the electrical box covers. (Refer to procedure 2)
(3) Disconnect the vane motor connector (CN151) on the
indoor controller board.
(4) Pull out the drain hose from the nozzle assembly, and
remove nozzle assembly. (See Photo 5)
Cable strap
Drain hose
5. REMOVING THE VANE MOTOR
Screw of electrical box
Photo 6
(1) Remove the nozzle assembly. (Refer to procedure 4)
(2) Remove 2 screws of the vane motor unit cover, and pull
out the vane motor unit.
(3) Remove 2 screws of the vane motor unit.
(4) Remove the vane motor from the vane motor unit.
(5) Disconnect the connector from the vane motor.
Screws of the vane motor unit
Screws of the vane motor unit cover
OCH447B
28
OPERATION PROCEDURE
PHOTOS
6. REMOVING THE INDOOR FAN MOTOR AND THE
LINE FLOW FAN
Photo 7
Screw of the motor band
(1) Remove the panel and the corner box. (Refer to procedure 1)
(2) Remove the electrical box (Refer to procedure 2) and the
nozzle assembly (Refer to procedure 4).
(3) Remove the water cut. (See Photo 2)
(4) Remove the screw fixing the line flow fan. (See Photo 8)
(5) Remove 5 screws fixing the motor bed. (See Photo 7)
(6) Remove the lead wire of pipe thermistor from the hook of
motor bed. (See Photo 7)
(7) Remove the screw fixing motor band. (See Photo 7)
(8) Remove the motor bed together with fan motor and motor
band.
(9) Remove 3 screws fixing the left side of the heat exchanger.
(See Photo 9)
(10) Lift the heat exchanger, and pull out the line flow fan to the
lower-left.
Lead wire of pipe thermistor
Screws of the motor bed
Photo 9
Photo 8
Screw of the line flow fan
Screws of the left side
of the heat exchanger
7. REMOVING THE LIQUID PIPE THERMISTOR AND
GAS PIPE THERMISTOR
(1) Remove the panel and the corner box. (Refer to procedure 1)
(2) Remove the electrical box covers. (Refer to procedure 2)
(3) Remove the water cut. (See Photo 2)
(4) Remove the liquid pipe thermistor and gas pipe thermistors.
(5) Disconnect the connector (CN44) (CN2G) on the indoor
controller board. (TH22 and TH23/CN44, TH24/CN2G)
Photo 10
Gas pipe thermistor
(TH23) (TH24)
LEV
Connect for ground
Liquid pipe thermistor (TH22)
OCH447B
29
OPERATION PROCEDURE
8. REMOVING THE HEAT EXCHANGER AND LEV
(1) Remove the panel and the corner box. (Refer to procedure 1)
(2) Remove the electrical box (Refer to procedure 3) and the
nozzle assembly (Refer to procedure 4).
(3) Remove the water cut.
(4) Remove the pipe thermistors (Refer to 7.).
(5) Disconnect the connector (CN60) on the indoor controller
board and the connector for ground wire.
(6) Remove 3 screws fixing the left side of the heat exchanger.
(See Photo 9)
(7) Remove the heat exchanger with LEV.
PHOTOS
Photo 11
Heat exchanger
LEV
Water cut
Photo 12
Heat exchanger
9. REMOVING THE ROOM TEMPERATURE THERMISTOR
(1)
(2)
(3)
(4)
LEV
Connect for ground
Photo 13
Remove the panel and corner box. (Refer to procedure 1)
Remove the electrical box covers. (Refer to procedure 2)
Remove the room temperature thermistor.
Disconnect the connector (CN20) on the indoor controller
board.
Indoor controller board
Room temp. thermistor
(TH21)
HEAD OFFICE : TOKYO BLDG., 2-7-3, MARUNOUCHI, CHIYODA-KU TOKYO 100-8310, JAPAN
Copyright 2008 MITSUBISHI ELECTRIC CORPORATION
Distributed in Dec. 2012 No. OCH447 REVISED EDITION-B
Distributed in May 2011 No. OCH447 REVISED EDITION-A
Distributed in Nov. 2008 No. OCH447 PDF 6
Made in Japan
New publication, effective Dec. 2012
Specifications are subject to change without notice.