Download Sharp XG-C50X Service manual
Transcript
XG-C50X SERVICE MANUAL SERVICE-ANLEITUNG S82O8XG-C50XU LCD PROJECTOR LCD PROJEKTOR MODEL MODELL XG-C50X In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified should be used. Im lnteresse der Benutzersicherheit (erforderliche Sicherheitsregeln in einigen Ländern) muß das Gerät in seinen Originalzustand gebracht werden. Außerdem dürfen für die spezifizierten Bauteile nur identische Teile verwendet werden. INHALT CONTENTS Page » SPECIFICATIONS ............................................. 2 » IMPORTANT SERVICE SAFETY NOTES (for USA) ............................................... 3 » NOTE TO SERVICE PERSONNEL ................... 4 » OPERATION MANUAL ...................................... 8 » REMOVING OF MAJOR PARTS ..................... 13 » RESETTING THE TOTAL LAMP TIMER ......... 15 » THE OPTICAL UNIT OUTLINE ....................... 16 » ELECTRICAL ADJUSTMENT ........................... 20 » TROUBLE SHOOTING TABLE ........................ 29 » CHASSIS LAYOUT .......................................... 90 » BLOCK DIAGRAM ........................................... 92 » OVERALL WIRING DIAGRAM ........................ 94 » SCHEMATIC DIAGRAM .................................. 96 » PRINTED WIRING BOARD ASSEMBLIES ... 138 » PARTS LIST Ë ELECTRICAL PARTS ................................ 148 Ë CABINET AND MECHANICAL PARTS ..... 164 Ë ACCESSORIES PARTS ............................ 169 Ë PACKING PARTS ....................................... 169 » PACKING OF THE SET ................................. 170 SHARP CORPORATION Seite » TECHNISCHE DATEN .................................... 48 » HINWEISE FÜR DAS WARTUNGSPERSONAL ................................ 49 » BEDIENUNGSANLEITUNG ............................ 51 » AUSBAU WICHTIGER TEILE ......................... 56 » RÜCKSTELLUNG DESLAMPEN-TIMERS ..... 58 » KURZBSCHREIBUNG DER OPTIK-EINHEIT ...................................... 59 » ELEKTRISCH EINSTELLUNG ........................ 63 » FEHLERSUCHTABELLE ................................. 72 » CHASSIS-ANORDNUNG ................................ 90 » BLOCKSCHALTBILD ....................................... 92 » GESAMTSCHALTPLAN .................................. 94 » SCHEMATISCHER SCHALTPLAN ................. 96 » LEITERPLATTENEINHEITEN ....................... 138 » ERSATZTEILLISTE Ë ELEKTRISCHE BAUTEILE ....................... 148 Ë GEHÄUSE UND MECHANISCHE BAUTEILE ................................................. 164 Ë ZUBEHÖRTEILE ....................................... 169 Ë VERPACKUNGSTEILE ............................. 169 » VERPACKEN DES GERÄTS ......................... 170 This document has been published to be used for after sales service only. The contents are subject to change without notice. XG-C50X Specifications Product type LCD Projector Model XG-C50X Video system NTSC 3.58/NTSC 4.43/PAL/PAL-M/PAL-N/PAL 60/SECAM/ DTV480I/DTV480P/DTV540P/DTV580I/DTV580P/DTV720P/DTV1035I/DTV1080I Display method LCD panel × 3, RGB optical shutter method LCD panel Panel size: 0.99" (25.1 mm) (15 [H] × 20 [W] mm) No. of dots: 786,432 dots (1,024 [H] × 768 [V]) Standard llens 1–1.27 × zoom lens, F1.7–2.2, f = 36.5–46.3 mm Projection lamp AC 250 W lamp Component input signal 15-pin mini D-sub connector (INPUT1/2) Y: 1.0 Vp-p, sync negative, 75 Ω terminated PB: 0.7 Vp-p, 75Ω terminated PR: 0.7 Vp-p, 75Ω terminated Horizontal resolution 750 TV lines (DTV720P) Computer RGB input signal 15-pin mini D-sub connector (INPUT 1/2) RGB separate/sync on green type analog input: 0–0.7 Vp-p, positive, 75Ω terminated HORIZONTAL SYNC. SIGNAL: TTL level (positive/negative) VERTICAL SYNC. SIGNAL: Same as above Video input signal RCA connector: VIDEO, composite video, 1.0 Vp-p, sync negative, 75Ω (INPUT 3) terminated S-video input signal 4-pin Mini DIN connector (INPUT 4) Y (luminance signal): 1.0 Vp-p, sync negative, 75Ω terminated C (chrominance signal): Burst 0.286 Vp-p, 75Ω terminated Computer control signal (RS-232C) 9-pin mini DIN connector Pixel clock 12–230 MHz Vertical frequency 43–200 Hz* Horizontal frequency 15–126 kHz Audio input signal ø3.5 mm minijack: AUDIO, 0.5 Vrms, more than 47 kΩ (stereo) Audio output 3.0 W (monaural) Speaker system 4 cm × 7 cm Rated voltage AC 100–240 V Input current 3.4 A Rated frequency 50/60 Hz Power consumption (normal) 340 W (Standard mode)/290 W (Low power mode) Power consumption (standby) About 0.8 W (When “Mntr.out/RS232” is set to “OFF”) Heat dissipation 1,280 BTU/hour Operating temperature 41°F to 104°F (+5°C to +40°C) Storage temperature –4°F to 140°F (–20°C to +60°C) Cabinet Plastic I/R carrier frequency 38 kHz Dimensions (approx.) 15 3⁄8" × 3 7⁄8" × 11 9⁄16" (390 (W) × 99.0 (H) × 294 (D) mm) (main body only) 15 1⁄2" × 4 7⁄16" × 11 5⁄8" (393 (W) × 114.0 (H) × 303.2 (D) mm) (including adjustment foot and projecting parts) Weight (approx.) 10.8 lbs. (4.9 kg) Supplied accessories Remote control, Two R-6 batteries, Power cord for U.S., Canada etc. (11'10", 3.6 m), Power cord for Europe, except U.K. (6', 1.8 m), Power cord for U.K., Hong Kong and Singapore (6', 1.8 m), Power cord for Australia, New Zealand and Oceania (6', 1.8 m), RGB cable (9'10", 3 m), USB cable (9'10", 3 m), Computer audio cable (9'10", 3 m), DIN-D-sub RS-232C adaptor (6 45⁄64", 15 cm), Extra air filter, Lens cap (attached), Dust cover, Projector manual and technical reference CD-ROM, Sharp Advanced Presentation Software CD-ROM, Operation manual, Quick reference label Replacement parts Lamp unit (Lamp/cage module) (BQC-XGC50X//1), Remote control (RRMCGA029WJSA), Two R-6 batteries (“AA” size, UM/SUM-3, HP-7, or similar), Power cord for U.S., Canada etc. (QACCDA010WJPZ), Power cord for Europe, except U.K. (QACCV4002CEZZ), Power cord for U.K., Hong Kong and Singapore (QACCBA012WJPZ), Power cord for Australia, New Zealand and Oceania (QACCL3022CEZZ), RGB cable (QCNWGA012WJPZ), USB cable (QCNWGA014WJPZ), Computer audio cable (QCNWGA013WJPZ), DIN-D-sub RS-232C adaptor (QCNWGA015WJPZ), Air filter (PFILDA005WJZZ), Lens cap (PCAPHA003WJSA), Dust cover (GCOVDA001WJZZ), Projector manual and technical reference CD-ROM (UDSKAA007WJZZ), Sharp Advanced Presentation Software CD-ROM (UDSKAA005WJN1), Operation manual (TINS-A163WJZZ), Quick reference label * Temporary noise may be visible with vertical frequencies above 100Hz if OSD functions are activated. This SHARP projector uses a LCD (Liquid Crystal Display) panel. This very sophisticated panel contains 786,432 pixels (× RGB) TFTs (Thin Film Transistors). As with any high technology electronic equipment such as large screen TVs, video systems and video cameras, there are certain accept- able tolerances that the equipment must conform to. This unit has some inactive pixels within acceptable tolerances which may result in inactive dots on the picture screen. This will not affect the picture quality or the life expectancy of the unit. Specifications are subject to change without notice. 2 XG-C50X IMPORTANT SERVICE SAFETY NOTES (for USA) Ë Service work should be performed only by qualified service technicians who are thoroughly familiar with all safety checks and servicing guidelines as follows: » Use an AC voltmeter with sensitivity of 5000 ohm per volt., or higher, sensitivity to measure the AC voltage drop across the resistor (See Diagram). » All checks must be repeated with the AC plug connection reversed. (If necessary, a non-polarized adapter plug must be used only for the purpose of completing these checks.) Any reading of 0.3 volts RMS (this corresponds to 0.2 milliamp. AC.) or more is excessive and indicates a potential shock hazard which must be corrected before returning the unit to the owner. WARNING 1. For continued safety, no modification of any circuit should be attempted. 2. Disconnect AC power before servicing. BEFORE RETURNING THE PROJECTOR: (Fire & Shock Hazard) Before returning the projector to the user, perform the following safety checks: 1. Inspect lead wires are not pinched between the chassis and other metal parts of the projector. 2. Inspect all protective devices such as non-metallic control knobs, insulating materials, cabinet backs, adjustment and compartment covers or shields, isolation resistor-capacity networks, mechanical insulators, etc. 3. To be sure that no shock hazard exists, check for current leakage in the following manner: » Plug the AC cord directly into a 120-volt AC outlet, (Do not use an isolation transformer for this test). » Using two clip leads, connect a 1.5k ohm, 10 watt resistor paralleled by a 0.15µF capacitor in parallel between all exposed metal cabinet parts and earth ground. AC VOLTMETER 1.5k ohm (10W) 0.15µF TEST PROBE TO EXPOSED METAL PARTS CONNECT TO KNOWN EARTH GROUND 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 SAFETY NOTICE AVIS POUR LA SECURITE Many electrical and mechanical parts in Projector have special safety-related characteristics. These characteristics are often not evident from visual inspection, nor can protection afforded by them be necessarily increased by using replacement components rated for higher voltage, wattage, etc. Replacement parts which have these special safety characteristics are identified in this manual; electrical components having such features are identified by “å” and shaded areas in the Replacement Parts Lists and Schematic Diagrams. For continued protection, replacement parts must be identical to those used in the original circuit. The use of a substitute replacement parts which do not have the same safety characteristics as the factory recommended replacement parts shown in this service manual, may create shock, fire or other hazards. De nombreuses pièces, électriques et mécaniques, dans les projecteur à présentent des caractéristiques spéciales relatives à la sécurité, qui ne sont souvent pas évidentes à vue. Le degré de protection ne peut pas être nécessairement augmentée en utilisant des pièces de remplacement étalonnées pour haute tension, puissance, etc. Les pièces de remplacement qui présentent ces caractéristiques sont identifiées dans ce manuel; les pièces électriques qui présentent ces particularités sont identifiées par la marque “å” et hachurées dans la liste des pièces de remplacement et les diagrammes schématiques. Pour assurer la protection, ces pièces doivent être identiques à celles utilisées dans le circuit d’origine. L’utilisation de pièces qui n’ont pas les mêmes caractéristiques que les pièces recommandées par l’usine, indiquées dans ce manuel, peut provoquer des électrocutions, incendies ou autres accidents. WARNING: The bimetallic component has the primary conductive side exposed. Be very careful in handling this component when the power is on. AVERTISSEMENT: La composante bimétallique dispose du conducteur primaire dénudé. Faire attention lors de la manipulation de cette composante sous tension. 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 3 XG-C50X NOTE TO SERVICE PERSONNEL 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 NOTE POUR LE PERSONNEL D’ENTRETIEN 12345678901234567890123456789012123456789012345 UV-RADIATION PRECAUTION 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 PRECAUTION POUR LES RADIATIONS UV 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 The light source, metal halide lamp, in the projector emits small amounts of UV-Radiation. La source de lumière, la lampe métal halide, dans le projecteur émet de petites quantités de radiation UV. AVOID DIRECT EYE AND SKIN EXPOSURE. EVITEZ TOUTE EXPOSITION DIRECTE DES YEUX ET DE LA PEAU. To ensure safety please adhere to the following: Pour votre sécurité, nous vous prions de respecter les points suivants: 1. Be sure to wear sun-glasses when servicing the projector with the lamp turned “on” and the top enclosure removed. 1. Toujours porter des lunettes de soleil lors d’un entretien du projecteur avec la lampe allumée et le haut du coffret retiré. 2. Do not operate the lamp outside of the lamp housing. 2. Ne pas faire fonctionner la lampe à l’extérieur du boîtier de lampe. 3. Do not operate for more than 2 hours with the enclosure removed. 3. Ne pas faire fonctionner plus de 2 heures avec le coffret retiré. UV-Radiation and Medium Pressure Lamp Precautions Précautions pour les radiations UV et la lampe moyenne pression 1. Be sure to disconnect the AC plug when replacing the lamp. 2. Allow one hour for the unit to cool down before servicing. 3. Replace only with same type lamp. Type BQCXGC50X//1 rated 85V/250W. 4. The lamp emits small amounts of UV-Radiation, avoid direct-eye contact. 5. The medium pressure lamp involves a risk of explosion. Be sure to follow installation instructions described below and handle the lamp with care. 1. To u j o u r s d é b r a n c h e r l a f i c h e A C l o r s d u remplacement de la lampe. 2. Laisser l’unité refroidir pendant une heure avant de procéder à l’entretien. 3. Ne remplacer qu’avec une lampe du même type. Type BQC-XGC50X//1 caractéristique 85V/250W. 4. La lampe émet de petites quantités de radiation UVéviter tout contact direct avec les yeux. 5. La lampe moyenne pression implique un risque d’explosion. Toujours suivre les instructions d’installation décrites ci-dessous et manipuler la lampe avec soin. 12345678901234567890123456789012123456789012345 4 XG-C50X 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 1234567890123456789012345678901212345678901234 UV-RADIATION PRECAUTION (Continued) 1234567890123456789012345678901212345678901234 1234567890123456789012345678901212345678901234 PRECAUTION POUR LES RADIATIONS UV (Suite) 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 Lamp Replacement Remplacement de la lampe Note: Remarque: Since the lamp reaches a very high temperature during units operation replacement of the lamp should be done at least one hour after the power has been turned off. (to allow the lamp to cool off.) Installing the new lamp, make sure not to touch the lamp (bulb) replace the lamp by holding its reflector 2. [Use original replacement only.] Comme la lampe devient très chaude pendant le fonctionnement de l’unité, son remplacement ne doit être effectué au moins une heure après avoir coupé l’alimentation (pour permettre à la lampe de refroidir). En installant la nouvelle lampe, s’assurer de ne pas toucher la lampe (ampoule). Remplacer la lampe en tenant son réflecteur 2. [N’utiliser qu’un remplacement d’origine.] 1 Lampe 1 Lamp 2 Reflecteur 2 Reflector DANGER ! –– Never turn the power on without the lamp to avoid electric-shock or damage of the devices since the stabilizer generates high voltages at its start. DANGER ! –– Ne jamais mettre sous tension sans la lampe pour éviter un choc électrique ou des dommages des appareils car le stabilisateur génère de hautes tensions à sa mise en route. Since small amounts of UV-Radiation are emitted from an opening between the duct cover and the lamp housing, it is recommended to place the LENS CAP on the opening during servicing to avoid eye and skin exposure. Comme de petites quantités de radiation UV sont émises par une ouverture entre le couvercle du conduit et le botier de la lampe,il est recommandé de placer le CAPUCHON D'OPTIQUE sur l'ouverture pendant l'entretien pour éviter une exposition des yeux et la peau. 5 XG-C50X WARNING: High brightness light source, do not stare into the beam of light, or view directly. Be especially careful that children do not stare directly in to the beam of light. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO MOISTURE OR WET LOCATIONS. CAUTION The lighting flash with arrowhead within a triangle is intended to tell the user that parts inside the product are risk of electric shock to persons. RISK OF ELECTRIC SHOCK. DO NOT REMOVE SCREWS EXCEPT SPECIFIED USER SERVICE SCREWS CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE CABINET. NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The exclamation point within a triangle is intended to tell the user that important operating and servicing instructions are in the manual with the projector. 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212 AVERTISSEMENT: Source lumineuse de grande intensité. Ne pas fixer le faisceau lumineux ou le regarder directement. Veiller particulièrement à éviter que les enfants ne fixent directement le faisceau lumineux. AVERTISSEMENT: AFIN D’EVITER TOUT RISQUE D’INCENDIE OU D’ELECTROCUTION, NE PAS PLACER CET APPAREIL DANS UN ENDROIT HUMIDE OU MOUILLE. ATTENTION L’éclair terminé d’une flèche à l’intérieur d’un triangle indique à l’utilisateur que les pi‘eces se trouvant dans l’appareil sont susceptibles de provoquer une décharge électrique. RISQUE D’ELECTROCUTION NE PASRETIRER LES VIS, A L’EXCEPTION DES VIS DE REPARATION UTILISATEUR SPECIFIEES Le point d’exclamation à l’intérieur d’un triangle indique à l’utilisateur que les instructions de fonctionnement et d’entretien sont détaillées dans les documents fournis avec le projecteur. ATTENTION: POUR EVITER TOUT RISQUE D’ELECTROCUTION, NE PAS RETIRER LE CAPOT. AUCUNE DES PIECES INTERIEURES N’EST REPARABLE PAR L’UTILISATEUR, A L’EXCEPTION DE L’UNITE DE LAMPE. POUR TOUTE REPARATION, S’ADRESSER A UN TECHNICIEN D’ENTRETIEN QUALIFIE. 6 XG-C50X Precautions for using lead-free solder 1 Employing lead-free solder "Input, Output, R/C Receiver, Key and Fan PWB" of this model employs lead-free solder. The LF symbol indicates lead-free solder, and is attached on the PWBs and service manuals. The alphabetical character following LF shows the type of lead-free solder. Example: LFa Indicates lead-free solder of tin, silver and copper. 2 Using lead-free wire solder When fixing the PWB soldered with the lead-free solder, apply lead-free wire solder. Repairing with conventional lead wire solder may cause damage or accident due to cracks. As the melting point of lead-free solder (Sn-Ag-Cu) is higher than the lead wire solder by 40°C, we recommend you to use a dedicated soldering bit, if you are not familiar with how to obtain lead-free wire solder or soldening bit, contact our service station or service ranch in your area. 3 Soldering As the melting point of lead-free solder (Sn-Ag-Cu) is about 220°C which is higher than the conventional lead solder by 40°C, and as it has poor solder wettabillty, you may be apt to keep the soldering bit in contact with the PWB for extended period of time. However, Since the land may be peeled off or the maximum heat-resistance temperature of parts may be excoeded, remove the bit from the PWB as soon as you conurm the steady soldering condition. Lead-free solder contains more tin, and the end of the soldering bit may be easily corroded. Make sure to tum on and off the power of the bit as required. if a different type of solder stays on the tip of the soldering bit, it is alloyed with lead-free solder. Clean the bit after every use of it. When the tip of the soldering bit is blackened during use, file it with steel wool or fine sandpaper. Becareful when replacing parts with polarity indication on the PWB silk. Lead-free wire solder for servicing Part No. ZHNDAi123250E ZHNDAi126500E ZHNDAi12801KE ★ J J J Description φ0.3mm 250g(1roll) φ0.6mm 500g(1roll) φ1.0mm 1kg(1roll) 7 Code BL BK BM XG-C50X Location of Controls Projector (Front and Top View) Power (ON/OFF) buttons INPUT button For switching input mode 1, 2, 3 or 4. Turn the power on or off. Power indicator KEYSTONE button Illuminates red, when the projector is in standby. When the power is turned on, this indicator will illuminate green. For adjusting Keystone or Digital Shift setting. AUTO SYNC button For automatically adjusting images when connected to a computer. Lamp replacement indicator Illuminates green indicating normal function. Replace the lamp when the indicator illuminates red. \ \ Adjustment buttons ( , ,\ , \ ) For selecting menu items. Temperature warning indicator VOLUME buttons For adjusting the speaker sound level. When the internal temperature rises, this indicator will illuminate red. MENU button For displaying adjustment and setting screens. UNDO button For undoing an operation or returning to the default settings. ENTER button For setting items selected or adjusted on the menu. HEIGHT ADJUST button Zoom knob Focus ring Adjustment foot Intake vent Carrying handle Remote control sensor Attaching and removing the lens cap • Press on the two buttons of the lens cap and attach it on the lens. Then release the buttons to lock it in place. • Press on the two buttons of the lens cap and remove it from the lens. 8 Air filter/cooling fan (Intake vent) (on the bottom of the projector) XG-C50X Projector (Rear View) AUDIO INPUT 1, 2 terminal USB Port Port for connecting a computer using a USB cable. Shared audio input terminal for INPUT 1 and 2. RS-232C terminal WIRED REMOTE control input terminal For controlling projector using a computer. INPUT 3 terminal AUDIO OUTPUT terminal For connecting video equipment. Shared audio output terminal for INPUT 1, 2, 3 and 4. AUDIO (L/R) INPUT 3, 4 terminals INPUT 1 terminal Shared audio input terminals for INPUT 3 and 4. Terminal for computer RGB and component signals. INPUT 4 terminal OUTPUT (INPUT 1, 2) terminal Terminal for connecting video equipment with an S-video terminal Shared computer RGB and component signals output terminal for INPUT 1 and 2. . INPUT 2 terminal Terminal for computer RGB and component signals. AC socket Exhaust vent Kensington Security Standard connector Adjustment Feet Using the Kensington Lock • This projector has a Kensington Security Standard connector for use with a Kensington MicroSaver Security System. Refer to the information that came with the system for instructions on how to use it to secure the projector. Carrying the projector Before carrying the projector, fully extend the carrying handle. 9 XG-C50X Remote Control (Front View) KEYSTONE button Power (ON/OFF) buttons For adjusting Keystone or Digital Shift setting. For turning the power on or off. MENU button ENTER button For displaying adjustment and setting screens. For setting items selected or adjusted on the menu. Adjustment buttons (', ", \, |) UNDO button For undoing an operation or returning to the default settings. For selecting menu items. PinP button ENLARGE (Enlarge/Reduce) buttons For displaying dual pictures. For enlarging or reducing part of the image. FORWARD/BACK buttons Moves forward or backwards when connected to a computer using a USB cable. Same as the [Page Down] and [Page Up] keys on a computer keyboard. GAMMA button For correcting the brightness of an image, when the images displayed are hard to see because of the brightness of the room. Four gamma modes are available to choose from. FREEZE button For freezing images. BLACK SCREEN button For superimposing a black screen. AUTO SYNC button For automatically adjusting images when connected to a computer. RESIZE button For switching the screen size (NORMAL, BORDER, etc). INPUT buttons For switching to the respective input modes. MUTE button For temporarily turning off the sound. VOLUME buttons BREAK TIMER button For adjusting the speaker sound level. For displaying the break timer. Remote Control (Top View) WIRED R/C JACK For controlling the projector by connecting the remote control to the projector. Remote control signal transmitters 10 XG-C50X Connection Pin Assignments INPUT 1/2 RGB and OUTPUT Signal Terminal: 15-pin Mini D-sub female connector RGB Input 5 10 15 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 1 6 11 Component Input Video input (red) Video input (green/sync on green) Video input (blue) Reserve input 1 Composite sync Earth (red) Earth (green/sync on green) Earth (blue) Not connected GND GND Bi-directional data Horizontal sync signal Vertical sync signal Data clock 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. PR (CR) Y PB (CB) Not connected Not connected Earth (PR) Earth (Y) Earth (PB) Not connected Not connected Not connected Not connected Not connected Not connected Not connected RS-232C Terminal: 9-pin Mini DIN female connector 8 9 7 6 3 4 5 2 Pin No. 1 2 3 4 Signal VCC RD SD EXIR 5 6 SG ERX 7 8 9 RS CS ETX 1 Name +3.3V (Reserved) Receive Data Send Data Detector of Option Unit (Reserved) Signal Ground IR Receive Signal from IR Amplifier (Reserved) Request to Send Clear to Send IR Transmit Signal (Reserved) I/O Output Input Output Input Reference Not connected Connected to internal circuit Connected to internal circuit Not connected Input Connected to internal circuit Not connected Output Input Output Not connected Not connected Not connected 9-pin D-sub male connector of the DIN-D-sub RS-232C adaptor 1 6 Pin No. 1 2 3 4 5 6 7 8 9 5 9 Signal CD RD SD ER SG DR RS CS CI Name I/O N Receive Data Send Data Input Output N Signal Ground Data Set Ready Request to Send Clear to Send N Output Input Reference ot connected Connected to internal circuit Connected to internal circuit ot connected Connected to internal circuit Not connected Connected to internal circuit Connected to internal circuit ot connected RS-232C Cable recommended connection: 9-pin D-sub female connector 5 9 Pin No. 1 2 3 4 5 6 7 8 9 1 6 Signal CD RD SD ER SG DR RS CS CI Pin No. 1 2 3 4 5 6 7 8 9 Signal CD RD SD ER SG DR RS CS CI Note • Depending on the system layout, it is necessary to connect Pin 4 and Pin 6 on the controlling device (e.g. PC). Projector Pin No. 4 5 6 PC Pin No. 4 5 6 USB Port: 4 pin B-type USB connector 2 1 3 4 Pin No. 1 2 3 4 Signal VCC USB– USB+ SG Name USB power USB data– USB data+ Signal Ground 11 XG-C50X Dimensions 1/8 (4) Rear View Top View Side View 3/16 (5.2) 11 9/16 (294) 8 7/16 (213.3) Side View 1/16 (1.5) 15 3/8 (390) 1/16 (1.5) 2 1/8 1 3/4 (54.5) (44.5) 3 1/8 (80) (15) Front View 3 7/8 (99) 5 (126.5) 9/16 9 1/2 (241.5) ø 67.5 3 15/16 (100.5) 4 3/8 (111.75) 2 15/16 (75) (7.5) 5/16 M4 M4 4 1/8 (104) Bottom View 4 15/16 (124.5) 2 11/16 (67.5) M4 M4 Units: inches (mm) 12 XG-C50X REMOVING OF MAJOR PARTS 1. Removal of the bottom filter cover and lamp unit cover 1-1. 1-2. 1-3. 1-4. Detach the bottom filter cover. Loosen the lock screw from the lamp unit cover, and detach the lamp unit cover. Pull out the carrying handle. Press the ~-marked spot of the upper half of the lens cover to unhook the claw, and detach the upper lens cover. 1-5. Detach the lower half of the lens cover. 2. Removal of the top panel and rear panel 2-1. Remove the six lock screws (black) and one lock screw (yellow) from the top panel. 2-2. Remove the eight lock screws from the rear panel and detach the rear panel. 2-3. Slowly lift the top panel and disconnect the connector from the key PWB. Remove another screw and detach the top panel. Lamp unit cover 1-2 1-4 Upper half of the lens cover 1-3 1-1 Carrying handle 1-5 Lower half of the lens cover Top panel Bottom filter cover 2-2 2-3 Rear panel 2-1 (Black) 2-1 (Yellow) 13 XG-C50X 3. Removal of the PWBs 3-1. 3-2. 3-3. 3-4. Remove the two lock screws from the lamp socket angle. Detach the lamp socket angle. Lift the ballast unit. Disconnect the connector and detach the ballast unit. Remove the lock screw from the PWB unit cover and detach the cover. Remove the three lock screws from the PWB assembly, disconnect the connector and detach the PWB assembly. 3-5. Remove the two lock screws from the cooling fan, disconnect the connector and detach the cooling fan. 3-6. Remove the lock screw from the grounding terminal, disconnect the connector and detach the AC inlet PWB. 4. Removal of the optical mechanism, fan PWB, power PWB and R/C receiver PWB 4-1. 4-2. 4-3. 4-4. Remove the seven lock screws from the optical mechanism, and take out the optical mechanism. Remove the lock screw from the cooling fan, and detach the cooling fan and fan PWB. Remove the four lock screws from the power PWB, and detach the power PWB. Take out the R/C receiver PWB. 3-5 3-4 3-4 Cooling Fan PWB Ass'y 3-1 Ballast Unit 3-6 3-2 AC Inlet PWB 4-1 3-3 4-2 Cooling Fan PWB Ass'y cover Fan PWB 4-1 4-3 4-3 Power PWB R/C Receiver PWB 14 XG-C50X RESETING THE LAMP TIMER 1 Connect the power cord. 2 Reset the lamp timer. • Plug the power cord into the AC socket of the projector. • While pressing simultaneously , AC socket ON and on the projector, press the projector. on • “LAMP 100%” is displayed, indicating that the lamp timer is reset. INPUT button ENTER button Power (ON) button UNDO buttom Info • Make sure to reset the lamp timer only when replacing the lamp. If you reset the lamp timer and continue to use the same lamp, this may cause the lamp to become damaged or explode. Ë The warning lights on the projector indicate problems inside the projector. Ë If a problem occurs, either the temperature warning indicator or the lamp replacement indicator will illuminate red, and the power will turn off. After the power has been turned off, follow the procedures given below. About the lamp replacement indicator Power indicator Lamp replacement indicator Temperature warning indicator About the temperature warning indicator If the temperature inside the projector increases, due to blockage of the air vents, or the setting lo” will blink in the cation, “ lower left corner of the picture. If the temperature keeps on rising, the lamp will turn off and the temperature warning indicator will blink, the cooling fan will run for further 90 seconds, then the power ” apwill be shut off. After “ pears, be sure to perform the following measures. Maintenance indicator Abnormal Normal Temperature warning indicator Lamp replacement indicator Power indicator Off Green on Green blinks when the lamp is active. Green on/ Red on Red on/ Power off Red blinks/ Red on Red on/ Power off Red blinks Condition ËThe lamp life becomes 0%, when used for approximately 2,000 hours with “ON” in “Power Save” or when used for approximately 1,500 hours with “OFF” in “Power Save”. ËWhen the remaining lamp life becomes 6% or less, “ ” will be displayed on the screen in yellow. When the percentage becomes 0%, “ ” will change to “ ” (red), the lamp will automatically turn off and then the projector as well. At this time, the lamp replacement indicator will illuminate in red. ËIf you try to turn on the projector a fourth time without replacing the lamp, the projector will not turn on. Problem Blocked air intake Possible Solution • Relocate the projector to an area with proper ventilation. The internal • Cooling fan breaktemperature is • Take the projector to your nearest down abnormally high. • Internal circuit failure Sharp Authorized Projector Dealer or Service Center for repair. • Clogged air intake • Remaining lamp life Time to change becomes 6% or • Carefully replace the lamp. the lamp under. • Take the projector to your nearest Sharp Authorized Projector Dealer or Service Center for repair. • Please exercise care when The lamp does • Burnt-out lamp • Lamp circuit failure not illuminate. replacing the lamp. The power indicator blinks in red when the projector is on. • The filter cover, lamp unit cover or lens cover is open. 15 • Securely install the filter cover. • If the power indicator blinks even when the filter cover is securely installed, contact your nearest Sharp Authorized Projector Dealer or Service Center for advice. XG-C50X THE OPTICAL UNIT OUTLINE Layout for proper setup of the optical components and parts (top view) Projection Lens Relay lens3 L2 M5 AL-coated mirror B M4 AL-coated mirror R Fly-eye lens (Output) Fly-eye lens (Input) L1 Relay lens 2 L2 M3 G reflector R reflector M2 B reflector Relay lens 1 Light source (Lamp) 16 XG-C50X Adjusting the mirrors This adjustment is needed when any of the optical parts of the optical mechanism has been replaced. 1. Disconnect the flat cables from all the LCD panels. 2. Light up the lamp. 3. Project a white-light image and check to see if there is any color tint in any direction. If any, use the M2, M4 and M5 adjusting levers. 4. Loosen the adjusting lever lock screws, make adjustments, and tighten up the lock screws. M5 Adjusting lever M4 Adjusting lever Lock screws Screw A Lock screws Lock screws M2 Adjusting lever Screw B Correcting color irregularities on white-only screen when replacing the lamp If color irregularities are found at the right and left on a white-only screen after replacing the lamp, it is necessary to readjust the optical axis of the new lamp. Take the following steps. 1. Open the lamp cover and loosen the screws A and B at the bottom of the lamp. 2. Using a screwdriver or the like, move the U-shaped groove at the window D in the arrow direction. 3. Temporarily fix the screws A and B, close the lamp cover, and check the white-only screen again for color irregularities. 4. Repeat the above steps 1 and 2 until there will be no color irregularities. Now tighten up the screws A and B. 5. Finally secure the lamp cover back in position. 17 XG-C50X Replacing the prism unit 1. Remove the four lock screws, and take the prism holder unit out of the optical unit. 2. Replace the prism unit with new one. Take the above step 1 in reverse order. Note: Even if just one of the LCD panels is defective, it is necessary to replace the entire prism unit. Do not replace just the defective LCD panel only. Under the present circumstances, please do not touch the display part of LCD. G-LCD panel R-LCD panel Prism unit lock screws B-LCD panel Optical unit 18 XG-C50X How to Release the System Lock Turn on the power. If the system lock is applied, the system-resetting screen appears. Press the following keys in this order. MENU → ENTER → ENTER → MENU → UNDO → UNDO → MENU After pressing the MENU key first, press the remaining six keys within 10 seconds. 19 XG-C50X ELECTRICAL ADJUSTMENT No. Adjustment Items Adjustment Conditions Adjustment Procedures 1 Initialization of EEPROM 1. Turn on the power (the lamp lights up) and warm up the system for 15 minutes. 1. Make the following settings. Press S2601 to enter the process mode, and execute S2 on the SSS menu. Now the EEPROM, except for the PC I/F unit, is initialized. Do not execute S1, or the PC I/F unit itself will be initialized. (The PC I/F unit has been factoryadjusted.) To adjust the PC I/F unit, refer to "How to Adjust the PC I/F unit" on the last page. 2 Adjustment of RGB1 black level signal amplitude 1. Select the following group and subjects. Group: OUTPUT1 Subject: G1-BLK, G1-GAIN For the color R, select the subjects R1-BLK and R1-GAIN. For the color B, select the subjects B1-BLK and B1-GAIN. 2. Make sure the process adjustment color bars are displayed. 3. For the color G, connect a oscilloscope to pin (2) of P1301. 4. For the colors R and B, connect the oscilloscope to pin (1) of P1301 and pin (3) of P1301, respectively. 1. Select the subject G1-GAIN. Using the set's control switch or the remote controller button, adjust the setting so that the signal amplitude is 4.0 Vp-p±0.05 V. 2. Select the subject G1-BLK. Using the set's control switch or the remote controller button, adjust the setting so that the white-to-white level is 1.8 Vp-p±0.1 V. 3. Do the same for the other colors R and B. ~ The G1 subjects are linked with the R1 and B1 subjects. When the G1-BLK setting has been changed, therefore, the R1-BLK and B1-BLK settings vary themselves accordingly. When the G1-GAIN setting has been changed, equally, the R1-GAIN and B1-GAIN settings vary themselves accordingly. First make the G1 settings and then readjust the R1 and B1 settings as required. 3 Adjustment of PSIG 1. Select the following group and subjects. Group: OUTPUT2 Subject: PSIG-H, PSIG-L Make sure the PSIG-H and PSIGL settings are 64 and 100, respectively. 1. Get the PSIG waveform displayed. (Feed the XGA signal.) PSIG 2.5V DC 5.6V DC GND Adjust the PSIG-H setting. Adjust the PSIG-L setting. 20 XG-C50X No. Adjustment Items Adjustment Conditions Adjustment Procedures 4 Checking of sample-and-hold pulse phase 1. Feed the XGA-mode 75-Hz black signal. 2. Select the following group and subject. Group: OUTPUT3 Subject: GCK-PHASE 1. Check the fixed value. Fixed value: 6 5 Adjustment of RGB countervoltage 1. Feed the counter-voltage adjustment signal (XGA) prepared by the Technical Department. 2. Select the following group and subjects. Group: OUTPUT3 Subject: RC (R), GC (G), BC (B) 1. Using the set's control switch or the remote controller button, adjust the settings to minimize flickers. 2. If the results are inconsistent at the center and on both sides onscreen, readjust the settings to get the same results on both sides. 6 Adjustment of RGB gradation reproduction 1. Feed the SMPTE pattern signal. 2. Select the following group and subject. Group: OUTPUT1 Subject: G1-BLK 1. Confirm that the 100% and 95% white gradation as well as the 0% and 5% black gradation are discernible. 2. If the white gradation looks differently, finely adjust the G1-BLK setting. 7 Adjustment of RGB white balance 1. Feed the 32-step gray scale signal (XGA, 60 Hz). 2. Select the following group and subjects. Group: OUTPUT1 Subjects: R1-BLK (R), B1-BLK (B) 1. Adjust the R1-BLK and B1-BLK settings to have the specified gradation balance (according to the standard monitor). 8 Adjustment of video AGC 1. Feed the NTSC 10-step gray scale signal. 2. Select the following group and subject. Group: VIDEO Subject: AGC-ADJ 3. Connect the oscilloscope between TP4501 and TP4502 1. Using the set's control switch or the remote controller button, adjust the setting so that the white-to-black level is 0.72 Vp-p±0.01 V. 9 Adjustment of video brightness/ contrast 1. Feed the NTSC100% window pattern signal. 2. Select the following group and subjects. Group: VIDEO Subject: AUTO, PICTURE/BRIGHT 1. Feed the signal. Using the set's control switch or the remote controller button, select the subject AUTO. The setting will adjust itself. 2. Then adjust the PICTURE/BRIGHT setting until the signal becomes bitless. 21 XG-C50X No. Adjustment Items Adjustment Conditions Adjustment Procedures 10 Adjustment of video tint 1. Feed the split color bar signal. 2. Select the following group and subject. Group: VIDEO1 Subject: TINT 1. Confirm the fixed value. Fixed value: 128 11 Adjustment of NTSC color saturation 1. Feed the split color bar signal. 2. Select the following group and subject. Group: VIDEO Subject: N-COLOR ~ Connect the oscilloscope to pin (1) of P1301. 1. Confirm the fixed value. Fixed value: 54 (Reference: 0.4 Vp-p) Adjustment of PAL 1. Feed the PAL color bar signal. color saturation 2. Select the following group and subject. Group: VIDEO Subject: P-COLOR ~ Connect the oscilloscope to pin (1) of P1301. 1. Confirm the fixed value. Fixed value: 51 (Reference: 0.4 Vp-p) Adjustment of SECAM color saturation 1. Feed the SECAM color bar signal. 2. Select the following group and subject. Group: VIDEO Subject: S-COLOR ~ Connect the oscilloscope to pin (1) of P1301. 1. Confirm the fixed value. Fixed value: 48 (Reference: 0.5 Vp-p) 12 13 100% White Red 100% White Red 100% White Red 14 Adjustment of video white balance 1. Feed the NTSC monoscope pattern signal. 2. Select the following group and subjects. Group: VIDEO Subjects: V-R1-BLK, V-B1-BLK 1. Using the set's control switch or the remote controller button, adjust the settings to have the same white balance as on the standard monitor. 15 Adjustment of COMPO brightness 1. Feed the 0% gray pattern signal (480I). 2. Select the following group and subject. Group: COMPO Subject: G-BRIGHT 1. Feed the signal to INPUT 1. Adjust the setting so that some bits should be missing onscreen. 22 XG-C50X No. Adjustment Items Adjustment Conditions Adjustment Procedures 16 Adjustment of COMPO CB offset and CR offset 1. Feed the Y-0% brightness, Cb and Cr 0% white pattern color difference signal (480I). 2. Select the following group and subject. Group: COMPO Subject: AUTO 1. Feed the signal. Using the set's control switch or the remote controller button, select the subject AUTO. The setting will adjust itself. 17 Adjustment of COMPO white balance 1. Feed the DTV monoscope pattern signal. 2. Select the following group and subjects. Group: DLP Subjects: C-R1-BLK, C-B1-BLK 1. Using the set's control switch or the remote controller button, adjust the settings to have the same white balance as on the standard monitor. 18 Adjustment of sRGB white balance 1. Feed the RGB 50% gray pattern signal. 2. Select the following group and subjects. Group: OUTPUT1 Subjects: S-R1-BLK, S-R1-GAIN, SG1-BLK, S-G1-GAIN, S-B1-BLK, SB1-GAIN 3. Have the BM-5 brightness meter and the standard white board at hand. 1. Make the S-R1-BLK setting the same as the R1-BLK one. Make the S-G1-BLK setting the same as the R1-BLK one. Make the S-B1-BLK setting the same as the R1-BLK one. Make the S-R1-GAIN setting the same as the R1-GAIN one. 2. Adjust the S-B1-GAIN and S-G1GAIN settings so that the chromaticity on the brightness meter should be as follows. x: .313±7/1000 y: .350±10/1000 Teaching intervals: 18 Brightness adjustable direction: Brightness up by increasing the setting (to be checked) Adjusting points: Three dimension (to be checked) Gradation 4 (to be checked) Gradation 5 (to be checked) Gradation 6 (to be checked) Other gradations not to be checked Adjustable colors: R, G and B adjustable (to be checked) (2) Color irregularity correction (adjustment) C50 conditions setup ( ) Correction procedure settings Gradation 7: 2. Lower-gradation correction value to be used. Gradation 6: 0. Correction with correction coefficient. Gradation 5: 0. Correction with correction coefficient. Gradation 4: 0. Correction with correction coefficient. Gradation 3: 1. Upper-gradation correction value to be used. Gradation 2: 1. Upper-gradation correction value to be used. Gradation 1: 4. Initial value to be used. Gradation 0: 4. Initial value to be used. For the model in question, select the name entered in (2) to start the color irregularity correction. If the set has its optical characteristics rather different from the standard ones or if the set has some color irregularity lines missing, do the teaching for that set in particular. Use its specified correction coefficients in making the adjustment. 23 XG-C50X No. Adjustment Items Adjustment Conditions Adjustment Procedures 19 Checking and readjustment of white balance 1. The adjusting conditions for each item are as follows: For RGB input, see Item 7. For video input, see Item 13. For COMPO input, see Item 16. 1. Make sure the white balance is as specified on the standard monitor. For readjustment, proceed in the order of RGB input, video input and COMPO input. 20 Checking colorrelated performance 1. Receive the color bar signal. 1. Select L1 in the process mode. Check the performance of color and tint. 21 Checking of picture-related performance 1. Receive the monoscope pattern signal. 1. Select L2 in the process mode. Check Picture, Brightness and Sharpness. 22 Checking of RGB performance 1. Receive the RGB signal. 1. Select L4 on the process mode. Check Picture, Brightness, Red, Blue, Clock, Phase, H-POS and V-POS. 23 Checking of offtimer performance 24 Checking of thermistor performance 1. Heat the thermistor with a hair dryer. 1. Make sure the temperature is displayed. 25 Automatic sync operation 1. Receive the phase checking pattern signal. 1. Make sure that Clock, Phase, H-POS and V-POS can be automatically adjusted in the VGA/S-VGA/XGA mode. 26 Checking of USB performance 1. Using the USB cable, connect the set to a personal computer. 1. Using the remote controller, make sure that feed and return operations are effective on the screen of the personal computer. 27 Factory settings 1. Select OFF in the process mode. Make sure that the off-timer starts with 5-minute display, counts down 1 minute for 1 second, and turns off when 0 minute is displayed. 1. Make the following settings. Destination / Process adjustment / Remote controller settings North-American models: S4 "Factory Setting 4" Domestic models: S5 "Factory Setting 5" Other models: North-America: S3 "Factory Setting 3" 24 XG-C50X How to Adjust the PC I/F unit 1. Initialization of EEPROM 1) Press SW2601 to enter the process mode. 2) Execute S1 on the SSS menu. (By S1, the PC board alone is initialized. Do not execute S2, or all the adjustment data, except for the PC I/F unit, is initialized.) 3) Make sure that the program version "VER. XXX" on the SPECIAL menu is the latest one. 2. Level adjustments 2-1. Setting the oscilloscope Set the oscilloscope's range to DC1V/div and 5µ S/div. 2-2. Connecting the PC interface 1) Connect the specified cable between ANALOG OUTPUT (on the signal generator) and DSUB connector (INPUT1 on the projector). 2) Set the projector's input selector to INPUT1. 3) Set the signal generator to XGA mode (1024x768, 60Hz, 32-step gradation). Also adjust the output amplitude (between black and white) to 700 mVp-p (terminated with a 75-ohm impedance). 4) Turn on the power. 2-3. Adjusting items 1) Adjustment of RGB drive/gain (1) Feed the window pattern signal that has 100% and 0% signals. (2) Select AUTO among the A/D items in the process mode and make the adjustments. 25 XG-C50X » Entering the adjustment process mode There are follwing two methods. » Press the SW2001 on the KEY PWB unit. » Press the follwing keys in this order. ON→Adj up→Adj down→Adj up→Adj down→ENTER→ENTER→MENU » Adjustment mode process menu Group Adjust PC Image A/D Sub Group Adjust RGB Image OUTPUT1 Adjust Panel Drive OUTPUT2 Adjust Commn Voltage OUTPUT3 Adjust Video Image VIDEO Adjust Component Image COMP 26 Subject R-BRIGHT G-BRIGHT B-BRIGHT R-D B-D G-D AD-AUT R1-BLK R1-GAIN G1-BLK G1-GAIN B1-BLK B1-GAIN S-R1-BLK S-R1-GAIN S-G1-BLK S-G1-GAIN S-B1-BLK S-B1-GAIN PSIG-H PSIG-L RC GC BC GCK-PHASE PICTURE BRIGHT TINT N-COLOR P-COLOR S-COLOR AGC-CNT AGC-ADJ STAT-GAIN V-R1-BLK V-B1-BLK VIDEO-AUTO G-BRIGHT CB-OFFSET CR-OFFSET C-R1-BLK C-B1-BLK COMPO-AUTO XG-C50X Group Process Mode LINE Sub Group Initial Setting SSS Sample Pattern PATTERN Adjust CVIC CVIC Subject L1 L2 L4 OFF TEMP OFF SENSOR CHECK TIME S1 S2 S3 S4 S5 RGB RGB[50] CROSS FOCUS STEP COLOR CHR PROGRESSIVE ENHANCE-VIDE ENHANCE-HDTV ENHANCE-RGB SCREEN NR PTG 27 MODE IP MDSW PTGSW C-TESTSW C-ILG-LY C-MOD-LY C-VE-LV ENH-PLUS ENH-MINUS DFC ENH-PLUS ENH-MINUS DFC MODE ENH-GAIN ENH-PLUS CUBIC-RGB CUBIC-VIDEO YNR-LEVEL YNR-K YNR-FSEL CNR-LEVEL CNR-K CNR-FSEL CNR-FILSW TBL-NO TESTSW ENABLE MV-F VDDYP XG-C50X Group Sub Group Subject CMS-HUE Adjust CVIC CMS-SAT CMS-VAL Adust Digital Convergence CONVER Vesion Cehck etc SPECIAL CC R-CNV-H G-CNV-H B-CNV-H R-CNV-V G-CNV-V B-CNV-V IPL IPL2 E2PROM ADR RD/WR USB-MODE 28 CMS-HUE-R CMS-HUE-Y CMS-HUE-G CMS-HUE-C CMS-HUE-B CMS-HUE-M CMS-SAT-R CMS-SAT-Y CMS-SAT-G CMS-SAT-C CMS-SAT-B CMS-SAT-M CMS-VAL-R CMS-VAL-Y CMS-VAL-G CMS-VAL-C CMS-VAL-B CMS-VAL-M DEGAMMA XG-C50X TROUBLE SHOOTING TABLE Lamp fails to light-up Turn on the power switch. Is discharging sound heard from lamp? Yes Is the lamp out of socket? Yes Reconnect the lamp into socket. No No Replace the lamp No Is the ballast cooling fan running? Check the power supply circuits. Yes Is DC 280V/400V voltage applied between CN704 connetor pins? No Check the power supply circuits. Yes Is 2V or higher voltage applied No between pins(4) and (2) of ballast's CN705 connector. Is the CN705 connector disconnected? Yes Yes Replace the ballast. Reconnect it into socket correctly. 29 No Check the microproccessor and its peripheral circuits. XG-C50X TROUBLE SHOOTING TABLE (Continued) Checking the power unit There is no voltage output at CN708 No Check the Output PWB unit Yes Which output voltage line fails? Other Check the T703, IC703, IC705, IC706 and their peripheral circuits. BU5.3V Is AC voltage(90~264V)applied across the CN701 connector? No Check the CN701 or AC cord. Yes Is AC voltage(90~264V)applied across the CN706 connector? Yes Yes Is the resistor R775 open? No No Replace Power unit. Yes Is the fuse F701 open? Replace the F701. No Is the resistor R702 open? Yes Replace the R702. No Is the Bimetal SW open Yes Push the red button of the bimetal. No Replace Inlet unit. 30 Replace the R775. XG-C50X TROUBLE SHOOTING TABLE (Continued) No audio output No Check the P301 and its peripheral circuits. Is its signal inputted into pin(2) and No (15) of IC303? Check the IC303 and its peripheral circuits. Is the audio signal outputted from the emmitor of Q306? Yes Yes No Is its signal inputted into pin(12) and (5) or pin(3) and (13) of IC302? Check theIC302 and its peripheral circuits. Yes Is its signal outputted from pin(14) and (15) or pin(16) and (17) of P3102? No Check the Q304 and Q305 and its peripheral circuits. No Check the connection between P3102 and SC3102. Yes Is its signal inputted into pin(14) and (15) or pin(16) and (17) of SC102? Yes Check the J431, J421 and their peripheral circuits. 31 XG-C50X TROUBLE SHOOTING TABLE (Continued) Checking the video system Is the lamp on ? No Go to "Lamp fails to light-up". Yes Is specified voltage EA connectors? No Check power circuit and its parts. Yes No Check the video terminal and its peripheral circuits. Is the signal outputted from the pin No (7) of IC4502? Check IC4502 and its peripheral circuits. Is the video signal inputted into the pin (23) of P3102? Yes Yes Is the signal outputted from the pin (5) of IC4505? No Check IC4505 and its peripheral circuits. No Check Q4501 and its peripheral circuits. Yes Is the signal inputted into pin(72) of P8002? Yes Go to "Checking the PC I/F unit". 32 XG-C50X TROUBLE SHOOTING TABLE (Continued) Checking the S-video system No Is the lamp on ? Go to "Lamp fails to light-up". Yes Is specified voltage EA connectors? No Check power circuit and its parts. Yes Is the video signal inputted into the pin (19) and (21) of P3102? No Check the video terminal and its peripheral circuits. No Check IC4502 and its peripheral circuits. No Check Q4513 and its peripheral circuits. No Check Q4502 and its peripheral circuits. Yes Is the Y-signal outputted from the pin (7) of IC4502? Yes Is the C-signal outputted from the emitter of Q4513? Yes Is the signal inputted into pin(72) and (73) of P8002? Yes Go to "Checking the PC I/F unit". 33 XG-C50X TROUBLE SHOOTING TABLE (Continued) Checking the RGB signal. Are the RGB signals outputted from No pin(16), (18) and (20) of IC3101? Check IC 3101 and its peripheral circuits. Yes Are their signals outputted from pin(26), (28) and (30) of P3102? No Check SC3102 and P3102 and their peripheral circuits. No Check Q2419 and Q2420 and their peripheral circuits. No Check IC2401,Q2401 Q2402 and Q2404 and their peripheral circuits. Yes Are their signals inputted into pin(1), (5) and (25)? Yes Are their signals inputted into pin(54), (58) and (62)? Yes Are their signals outputted from pin(45)-(54), pin(57)-(66) and pin(69)-(78) of P8001? No Goto "Checking the PC I/F unit". Yes No Are their signals inputted into IC1101, IC1102, IC1201, IC1202, IC1301 and IC1302? Check IC1101,IC1102,IC1201, IC1202,IC1301 and IC1302 and their peripheral circuits. Yes Are their sgnals inputted into SC1101, SC1201, SC1301? Yes Check the connection of LCD panels And when video signal and OSD are also not displaied, replace the LCD panels. 34 XG-C50X TROUBLE SHOOTING TABLE (Continued) Checking the RGB Sync. Are the sync inputted into pin(2) and (4) of SC3102? No Check IC3152, IC3153, IC3154 and IC3151and their peripheral circuits. No Check P3102 and its peripheral circuits. No Check IC2404 and its peripheral circuits. Yes Are their signal inputted into pin(2) and (12) of IC2404? Yes Are their signal inputted into pin(63) and (66) of P8002? Yes Go to "Checking the PC I/F unit". 35 XG-C50X TROUBLE SHOOTING TABLE for PC I/F UNIT Checking of PC I/F UNIT 0 Is the user menu displayed onscreen? Yes Yes Check the onscreen display. Check the RGB input. Yes Check the component input. Yes Check the video input. Yes End 36 XG-C50X TROUBLE SHOOTING TABLE for PC I/F UNIT (Continued) Checking of Onscreen Display Is the user menu displayed onscreen normally by the MENU key? Yes No problem with the onscreen display. No Enter the process menu and select PATTERN. Then select the COLOR pattern. Is the onscreen display color normal? No Yes In the process mode, make the LCD line adjustment. Select the STEP signal. 0 Is the STEP signal as specified? Yes No Rewrite the onscreen display data. 0 Is the signal compatible with the STEP signal outputted at TL106 thru TL111? Yes No IC8025 is defective. Go to "Checking of GA4 and Its Periphery". Rewrite the onscreen display data. 37 XG-C50X TROUBLE SHOOTING TABLE for PC I/F UNIT (Continued) Checking of RGB Input Feed the sync separation type analog RGB signal to INPUT1. 1 Select INPUT1 using the set's key or the remote controller. 2 Does the picture appear? No Yes Is the picture disturbed? Go to "Confirmation of Video Input". Yes No 3 Go to "Checking of Sync Signal". Do the three colors R, G and B appear? No Yes Go to "Checking of RGB Signal". Carry out the AUTOSYNC process. Is the contour of picture clear? No Yes Is there any disturbance in the vertical stripe pattern? No Yes IC8013, IC8025 or their periphery is defective. End 38 XG-C50X TROUBLE SHOOTING TABLE for PC I/F UNIT (Continued) Confirmation of Video Input Make "Confirmation of Input Signal Setting". Is there the video signal at the land of C8070? No Yes Is there the signal at pin (55) of SC8002 (B-to-B connector)? Go to "Checking of Sync Signal". Yes Somewhere in the signal route is defective. Check the capacitors and resistors between SC8002 and IC8013. IC8025 or IC8013 is defective. The signal source or connector is defective. Confirmation of Input Signal Setting Is the right item selected from input menu? No Yes Select the right item. 2 Are the connectors connected correctly? No Yes Connect the connectors correctly. End 1 39 No XG-C50X TROUBLE SHOOTING TABLE for PC I/F UNIT (Continued) Checking of Sync Signal Is there the vertical sync signal at pin (11) of IC8363? No Yes Is there the horizontal sync signal at pin (5) of IC8363? No Yes Make confirmation of input signal setting. R997, R996, SC8002 or their periphery is defective. Is there the vertical sync signal at TL8131? No Yes Is there the horizontal sync signal at TL8130? No Yes Are both the vertical and horizontal sync signals in appropriate timing? IC8363 is defective. Yes No The sync signals are as specified. End of checking. Is the signal generator (input source) appropriate? Yes No Set the signal source appropriately. R997, R996, SC8002 or their periphery is defective. 2 40 XG-C50X TROUBLE SHOOTING TABLE for PC I/F UNIT (Continued) Checking of R, G and B Signals Is the signal type set to RGB? No Yes Set the signal type to RGB. Set the process mode. Select R, G and B individually on the pattern menu. Go to "Checking of GA4 and Its Periphery". For checking the input signal, set the signal generator to gradation signal. Measure the signals at TL8169, TL8170 and TL8180 on the oscilloscope. (MSB bit after A/D conversion) Are there the specified signals at TL8169, TL8170 and TL8180? Yes IC8025 or its periphery is defective. No Does the signal come to C8062, C8070 and C8078? No Yes IC8013 or its periphery is defective. 41 Go to "Confirmation of Video Input". XG-C50X TROUBLE SHOOTING TABLE for PC I/F UNIT (Continued) Checking of GA4 and Its Periphery Select R, G and B individually on the pattern menu in the process mode. Is picture outputted appropriately in R, G and B? Yes No Checking of GA4 and its periphery ends. Measure the signals at pins (54), (66) and (78) of SC8001 on the oscilloscope. These signals are MSB of B/G/R/. Do the oscilloscope-measured signals match with those selected on the pattern menu? Yes No The OUTPUT PWB is defective. Does the clock signal come to pins No (40) and (42) of SC8001? Yes Is there the clock (37.5 MHz) signal at TL8114? Yes No IC8029 is defective. Is there the clock (37.5 MHz) signal at FL8110? Measure the signals at TL8106, TL8107, TL8108, TL8110 and TL8111 on the oscilloscope. Yes X8005 is defective. IC8025 is defective. Do the oscilloscope-measured signals match with those selected on the pattern menu? Yes No No IC8025 is defective. IC8029 is defective. 42 XG-C50X TROUBLE SHOOTING TABLE for PC I/F UNIT (Continued) Checking of Component Input (except 480I) Feed the component signal to INPUT1. Select INPUT1 using the set's key or the remote controller. Does the picture appear? No Yes 4 Go to "Checking of SOG Circuit". Are the colors normal? No Is the signal type set at component? No Yes Set the signal type to component. Carry out the process adjustment. 4 Is the contour of picture clear? No Yes The component is normal. End. IC8013 or IC8025 is defective. 43 XG-C50X TROUBLE SHOOTING TABLE for PC I/F UNIT (Continued) Checking of SOG Circuit Measure the signal at pin (2) of IC8365 on the oscilloscope. Is the composite sync signal reproduced in correct timing? Yes No The SOG circuit is normal. End. Measure the land of C8070 on the oscilloscope. Is there the Y signal including sync signal? No Yes The SOG sync separation circuit (INPUT PWB) is defective. Go to "Confirmation of Input Signal Setting". 44 XG-C50X TROUBLE SHOOTING TABLE for PC I/F UNIT (Continued) Checking of Video Input Feed the composite video signal to INPUT3. Select INPUT3 using the set's key or the remote controller. 5 Does the picture appear? No Yes Is there any disturbance in the picture? Go to "Checking of Video Sync Signal". Yes No Are the colors normal? Go to "Checking of Video Sync Signal". Carry out the process adjustment. No 5 Yes The video input is normal. End. Is the video signal inputted to C8141? No Yes Is there the signal at R8114? 6 Yes Q8002 or its periphery is defective. No No Is there the signal at pin (3) of SC8002? Yes R8114 or its periphery is defective. The INPUT/OUTPUT PWB is defective. 45 XG-C50X TROUBLE SHOOTING TABLE for PC I/F UNIT (Continued) 6 Check the clock signal of IC8015 by FL8114. Is the clock signal normal? No Yes IC8015 is defective. Go to "Checking of Video Sync Signal". IC8025 or its periphery is defective. Checking of Video Sync Signal Measure the signal at pin (10) of IC8363 on the oscilloscope. (Checking of vertical sync signal) Is the vertical sync signal normal? No Yes Measure the signal at pin (6) of IC8363 on the oscilloscope. (Checking of horizontal sync signal) Is the horizontal sync signal normal? No Go to "Confirmation of Input Signal Setting". Yes 7 46 XG-C50X TROUBLE SHOOTING TABLE for PC I/F UNIT (Continued) 7 Are the horizontal and vertical sync signals outputted at TL8130 and TL8131, respectively? No IC8015 or its periphery is defective. Yes Is there the specified clock (13.5 MHz) signal at FL8114? Yes No IC8015 or its periphery is defective. End. 47 XG-C50X Technische Daten Produkttyp LCD PROJEKTOR Modell XG-C50X Videosystem NTSC 3.58/NTSC 4.43/PAL/PAL-M/PAL-N/PAL 60/SECAM/ DTV480 /DTV480P/DTV540P/DTV580 /DTV580P/DTV720P/DTV1035 /DTV1080 Wiedergabeverfahren LCD-Panel x 3, optische RGB-Verschlussmethode LCD-Panel Panel-Größe: 0,99tum(25,1 mm)(15[H] × 20[B] mm) Anzahl der Bildpunkte: 786.432 Bildpunkte (1.024 [H] × 768 [V]) Standard-Objektiv 1–1,27 × Zoom-Objektiv, F1,7–2,2, f = 36,5–46,3 mm Projektionslampe Wechselstromlampe 250 W Komponenten-Eingangssignale 15-poliger Mini-D-Sub-Anschluss (INPUT 1/2) Y: 1,0 Vs-s, negatives Sync., 75 Ω terminiert PB: 0,7 Vs-s, 75 Ω terminiert PR: 0,7 Vs-s, 75 Ω terminiert Horizontale Auflösung 750 Fernsehzeilen (DTV720P) Computer-RGB-Eingangssignal 15-poliger Mini-D-Sub-Anschluss (INPUT 1/2) RGB getrennt/Sync auf Grün-Typ analoger Eingang: 0-0,7 Vs-s, positiv, 75 Ω terminiert HORIZONTALES SYNC.-SIGNAL: TTL-Pegel (positiv/negativ) VERTIKALES SYNC.-SIGNAL: Wie oben Videoeingangssignal RCA-Anschluss: VIDEO, gemischtes Video, 1,0 Vs-s, negatives Sync., 75 Ω terminiert (INPUT 3) S-Videoeingangssignal 4-pol. Mini DIN-Anschluss (INPUT 4) Y (Luminanzsignal): 1,0 Vs-s, negatives Sync., 75 Ω terminiert C (Chrominanzsignal): Stoß 0,286 Vs-s, 75 Ω terminiert Computer-Steuerungssignal (RS-232C) 9-Pin Mini-DIN-Stecker Pixeltakt 12-230 MHz Vertikale Frequenz 43-200 Hz* Horizontale Frequenz 15-126 kHz Audioeingangssignal ø 3,5 mm Minibuchse: AUDIO, 0,5 Vrms, mehr als 47 kΩ (Stereo) Audioausgang 3,0 W (Mono) Lautsprechersystem 4 cm × 7 cm Nennspannung 100-240 V Wechselstromspannung Eingangsspannung 3,4 A Nennfrequenz 50/60 Hz Leistungsaufnahme (normal) 340 W (Standard-Modus)/290 W (Modus mit niedrigem Stromverbrauch) Leistungsaufnahme (Bereitschaft) Ca. 0,8 W (wenn “Monitor/RS232” auf “OFF” gestellt ist) Wärmeableitung 1.280kWh Betriebstemperatur 41°F bis 104°F (+5°C bis +40°C) Lagertemperatur – 4°F bis 140°F (–20°C bis +60°C) Gehäuse Plastik I/R-Trägerfrequenz 38 kHz Abmessungen (ca.) 15 3⁄8" × 3 7⁄8" × 11 9⁄16" (390 (B) × 99,0 (H)× 294 (T) mm) (nur Hauptgerät) 15 1⁄2" × 4 7⁄16" × 11 5⁄8" (393 (B) × 114,0 (H) × 303,2 (T) mm) (einschließlich Drehfüße und Projektionsteile) Gewicht (ca.) 11,3 lbs. (5,1 kg) Mitgeliefertes Zubehör Fernbedienung, zwei R6-Batterien, Netzkabel für USA, Kanada usw. (11'10", 3,6 m), Netzkabel für Europa, ausgenommen Großbritannien (6', 1,8 m), Netzkabel für Großbritannien, Hongkong und Singapur (6', 1,8 m), Netzkabel für Australien, Neuseeland und Ozeanien (6', 1,8 m), RGB-Kabel (9' 10", 3m), USB-Kabel (9' 10", 3m), Audio-Computerkabel (9' 10", 3m), DIN-D-Sub RS232C-Adapter (6 45⁄64", 15 cm), zusätzlicher Luftfilter, Objektivkappe (befestigt), Projektorhandbuch-und technische ReferenzCD-ROM, Sharp Advanced Presentation Software CD-ROM, Bedienungsanleitung,Kurzanleitungskennung Ersatzteile Lampeneinheit (Lampen-/Gehäusemodul) (BQC-XGC50X//1), Fernbedienung (RRMCGA029WJSA), zwei R 6-Batterien (“AA”, UM/SUM-3, HP-7 oder ähnlich), Netzkabel für USA, Kanada usw. (QACCDA010WJPZ), Netzkabel für Europa, ausgenommen Großbritannien (QACCV4002CEZZ), Netzkabel für Großbritannien, Hongkong und Singapur (QACCBA012WJPZ), Netzkabel für Australien, Neuseeland und Ozeanien (QACCL3022CEZZ),RGB-Kable (QCNWGA012WJPZ), USB-Kable (QCNWGA014WJPZ), Audio-Computerkabel (QCNWGA013WJPZ), DIN-D-Sub RS-232C-Adapter (QCNWGA015WJPZ), Luftfilter (PFILDA005WJZZ), Objektivkappe (PCAPHA003WJSA), Projektorhandbuch-und- technische Referenz-CD-ROM (UDSKAA007WJZZ), Sharp Advanced Presentation Software CD-ROM (UDSKAA005WJN1), Bedienungsanleitung (TINSA163WJZZ), Kurzanleitungskennung. *Bei vertikalen Frequenzen über 100 Hz kann eine zeitweise Störung sichtbar werden, wenn die OSD-Funktionen eingeschaltet sind. Dieser SHARP Projektor verwendet eine LCD (Liquid Crystal Display)-Anzeige.Diese hochmoderne Anzeige enthält 786.432 Pixel (xRGB) TFTs (Thin Film Transistors). Bei allen technologisch fortschrittlichen, elektronischen Geräten, z. B. Großbild-Fernsehern, Videosystemen bzw. Videokameras, sind bestimmte Toleranzgrenzen für die Funktionen gegeben. Dieses Gerät hat einige inaktive, innerhalb akzeptierter Toleranzgrenzen liegende Bildpunkte, die als leuchtende oder als nicht aktive Punkte auf der Bildwand wiedergegeben werden. Dies hat keinen Einfluss auf die Bildqualität oder die Lebensdauer des Gerätes. Änderungen der technischen Daten ohne vorherige Ankündigung vorbehalten. 48 XG-C50X HINWEIS FÜR DAS WARTUNGSPERSONAL 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 Ë Auswechseln der Lampe ACHTUNG: UV-STRAHLUNG 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 12345678901234567890123456789012123456789012345 Hinweis: Da die Lampe während des Betriebs sehr heiß wird, sollte die Lampe erst ausgewechselt werden, nachdem das Gerät mindestens eine Stunde ausgeschaltet war, damit die Lampe ausreichend abkühlen kann. Beim Installieren der neuen Lampe muß darauf geachtet werden, die Lampe selbst (Glaskolben) nicht zu berühren. Vielmehr muß die Lampe am Reflektor 2 gehalten werden. [Es darf nur ein Original-Ersatzteil verwendet werden.] Die Lichtquelle im Projektor, eine Metall-HalogenLampe, gibt eine geringe UV-Strahlung ab. DIREKTE BESTRAHLUNG AUF AUGEN UND HAUT MUSS VERMIEDEN WERDEN. Zur Gewährleistung der Sicherheit muß folgendes beachtet werden: 1. Bei Arbeiten am Projektor bei eingeschalteter Lampe und abgenommenem oberen Gehäuse muß unbedingt eine Sonnenbrille getragen werden. 1 Lampe 2 Reflektor GEFAHR! — Niemals die Spannungsversorgung einschalten, ohne daß eine Lampe vorhanden ist, um elektrische Schläge und Schäden am Gerät zu vermeiden, da der Stabilisator anfangs hohe Spannungen erzeugt. 2. Die Lampe darf nicht außerhalb des Lampengehäuses eingeschaltet werden. Da eine geringe UV-Strahlung aus einer Öffnung zwischen der Schachtabdeckung und dem Lampengehäuse austritt, sollte der Objektivdeckel bei Wartungsarbeiten auf die Öffnung gesetzt werden, um die Bestrahlung von Augen und Haut zu vermeiden. 3. Betrieb für länger als 2 Stunden bei abgenommenem Gehäuse ist nicht zulässig. Zur Beachtung bei UV-Strahlung und Mitteldruck-Lampen 1. Vor dem Auswechseln der Lampe muß der Netzstecker gezogen werden. 2. Vor Durchführung von Wartungsarbeiten muß das Gerät eine Stunde abkühlen. 3. Nur mit dem gleichen Lampentyp ersetzen Typ BQC-XGC50X//1; Nennleistung 85 V/250 W. 4. Die Lampe gibt eine geringe UV-Strahlung ab, daher muß direkter Augenkontakt vermieden werden. 5. Die Mitteldruck-Lampe weist ein Explosionsrisiko auf. Daher müssen die nachstehenden Installationsanweisungen beachtet werden, und die Lampe muß vorsichtig behandelt werden. 49 XG-C50X Vorsichtsmaßregeln für bleifreien Lötzinn 1 Verwendung von bleifreiem Lötzinn Die "Eingangs-, Ausgangs-, Fernbedienungs-, Schlüsell-, Fächer-Platine" dieses Modells verwendet bleifreien Lötzinn. Das LF-Symbol zeigt bleifreien Lötzinn an und ist an den Platinen und Wartungsanleitungen angebracht. Der Buchstabe nach LF zeigt den Typ des bleifreien Lötzinns an. Beispiel: LFa Zeigt bleifreien Lötzinn aus Zinn, Silber und Kupfer an. 2 Bei Reparatur der mit bleifreiem Lötzinn gelöteten Platine immer bleifreien Lötzinn verwenden. Reparatur mit herkömmlichem Lötzinn kann zu Schäden oder Unfällen aufgrund von Rissen führen. Da der Schmelzpunkt bleifreien Lvtzinns (Sn-Ag-Cu) um 40°C höher als der von Bleidraht-Lötzinn ist, empfehlen wir die Verwendung einer speziellen Lötspitze. Wenn Fragen über den Beschaffung leitfreien Lötzinns oder spezieller Lötspitzen bestehen, wenden Sie sich an unsere Kundendienstvertretung in Ihrem Gebiet. 3 Löten Da der Schmelzpunkt bleifreien Lötzinns (Sn-Ag-Cu) etwa 220°C beträgt, was um 40°C höher als der von bleihaltigem Lötzinn ist, und außerdem schlechte Löt-Benetzbarkeit aufweist, kann es erforderlich werden, die Lötspitze längere Zeit in Kontakt mit der Platine zu halten. Da die Lötlauge abfliessen kann oder der maximale Hitzewiderstand von Teilen überschritten werden kann, die Lötspitze sofort von der Platine nehmen, sobald eine gute Lötung erzielt ist. Bleifreier Lötzinn enth_lt mehr Zinn, und das Ende der Lötspitze kann leicht angegriffen werden. Immer sicherstellen, dass der Lötkolben nur bei Bedarf eingeschaltet wird. Wenn ein anderer Typ von Lötzinn an der Lötspitze haften bleibt, verschmilzt er mit dem bleifreien Lötzinn. Die Lötspitze nach jeder Verwendung reinigen. Wenn die Lötspitze bei der Verwendung geschwärzt wird, die Spitze mit Stahlwolle oder feinem Sandpapier abschmirgeln. Immer beim Austausch von Teilen vorsichtig sein, und die Polaritätsanzeige auf der Platinenbeschriftung beachten. Bleifreier Lötzinn zur Wartung Teile-Nr. ZHNDAi123250E ZHNDAi126500E ZHNDAi12801KE ★ J J J Beschreibung φ0.3mm 250g(1roll) φ0.6mm 500g(1roll) φ1.0mm 1 Rolle 50 Code BL BK BM XG-C50X Bedienelemente Projektor (Vorder- und Draufsicht) Netz-Tasten(ON/OFF) INPUT-Taste Schaltet die Stromversorgung ein oder aus. Für das Umschalten zwischen Eingangsmodus 1, 2, 3 und 4. Netz-Anzeige KEYSTONE-Taste Leuchtet rot, wenn sich der Projektor im Bereitschaftsbetrieb befindet. Wenn die Stromversorgung eingeschaltet ist, leuchtet diese Anzeige grün. Für das Einstellen der Trapezverzerrungs- oder Digitalen Verschiebungs-Einstellung. AUTO SYNC-Taste LAMP-Anzeige (Lampenaustausch) Für das automatische Einstellen von Bildern, wenn ein Computer angeschlossen ist. Bei vorschriftsmäßiger Funktion leuchtet diese Anzeige grün. Die Lampe austauschen, wenn die Anzeige rot .leuchtet Einstelltasten (', ", \, |) Für die Wahl der Menüpunkte. TEMP.-Anzeige (Temperaturwarn) VOL-Tasten Wenn die interne Temperatur ansteigt, leuchtet diese Anzeige . rot Für das Einstellen des Lautsprecher-Tonpegels. MENU-Taste UNDO-Tast e Für das Rückgängigmachen eines Bedienschrittes oder für die Rückkehr zu den Grundeinstellungen. Für die Anzeige des Justierungsund Einstellungsbildschirms. ENTER-Taste Für die Einstellung der gewählten oder eingestellten Menüpunkte. HEIGHT ADJUST-Taste Zoom-Knopf Fokusring Einstellfuß Luftzufuhr Tragegriff Fernbedienungssensor Anbringen und derder Objektivkappe Anbringen undAbnehmen Abnehmen Objektivkappe Drücken Sie beiden Tasten der Objektivkappe, •O Drücken Sieananden den beiden Tasten der und bringen Sie diese anbringen dem Objektiv an. Danach Objektivkappe, und Sie diese an dem geben Sie die Tasten frei, um die Objektivkappe zu Objektiv an. Danach geben Sie die Tasten frei, um verriegeln. die Objektivkappe zu verriegeln. O Drücken Sie die beiden Tasten der Objektivkappe, und •nehmen Drücken die beiden Tasten derObjektiv Objektivkappe, Sie Sie die Objektivkappe von dem ab. und nehmen Sie die Objektivkappe von dem Objektiv ab. 51 Luftfilter/Ventilator (Luftzufuhr) (auf der Unterseite des Projektors) XG-C50X Projektor (Hintersicht) USB-Anschluss AUDIO INPUT 1, 2Anschluss Für den Anschluss eines Computers unter Verwendung eines USBKabels. Geteilter Audioeingabeanschluss für INPUT 1 und 2. WIRED REMOTEEingabeanschluss RS-232C-Anschluss Für die Bedienung des Projektors über Computers. INPUT 3-Anschluss Für den Anschluss eines Videogerätes. AUDIO OUTPUTAnschluss AUDIO (L/R) INPUT 3, 4-Anschlüsse Geteiltes Audio Ausgabeanschluss r fü INPUT 1, 2, 3 und 4. INPUT 1-Anschluss Geteilter Audioeingabeanschluss für INPUT 3 und 4. Anschluss für Computer RGB und Komponentensignale. INPUT 4-Anschluss OUTPUT (INPUT 1, 2)Anschluss Anschluss für ein Videogerät mit einem SVIDEO-Anschluss. Geteilter Computer-RGBund KomponentensignaleAusgabeanschluss r fü INPUT 1 und 2. INPUT 2-Anschluss Anschluss für Computer RGB und Komponentensignale. Netzanschluss Luftaustritt-öffnung KensingtonSicherheitsstandardanschluss Einstellfuß Verwendung der Kensington-Sperre • Dieser Projektor ist mit einem Kensington-Sicherheitsstandardanschluss für die Verwendung des Kensington MicroSaver-Sicherheitssystem ausgestattet. Lesen Sie hinsichtlich der Verwendung die Informationen, die dem System beiliegen, um den Projektor zu sichern. Transportieren des Projektors Bevor Sie den Projektor transportieren, muss der Tragegriff vollkommen ausgeklappt werden. 52 XG-C50X Fernbedienung (Vordersicht) Netz-Tasten(ON/OFF) KEYSTONE-Taste MENU-Taste ENTER-Taste Einstelltasten (', ", \, |) UNDO-Taste PinP-Taste ENLARGE-Tasten (Vergrößern/Verkleinern) FORWARD/BACK-Tasten GAMMA-Taste FREEZE-Taste BLACK SCREEN-Taste AUTO SYNC-Taste RESIZE-Taste INPUT-Tasten MUTE-Taste VOL-Tasten BREAK TIMER-Taste Fernbedienung (Draufsicht) WIRED R/C JACK Signalsender für Fernbedienung 53 XG-C50X Pin-Belegung INPUT-1/2-RGB und OUTPUT-Signalanschluss: 15-Pin Mini-D-Sub weiblich RGB-Eingabe 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 1 6 11 5 10 15 Komponenteneingabe Videoeingabe (rot) Videoausgabe (grün/sync auf grün) Videoausgabe (blau) Reserveeingabe 1 Composite-Sync Erde (rot) Erde (grün/sync auf grün) Erde (blau) nicht angeschlossen GND GND Bi-directionale Daten Horizontal-Sync-Signal Vertikal-Sync-Signal Datenuhr 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. PR (CR) Y PB (CB) Nicht angeschlossen Nicht angeschlossen Erde (PR) Erde (Y) Erde (PB) Nicht angeschlossen Nicht angeschlossen Nicht angeschlossen Nicht angeschlossen Nicht angeschlossen Nicht angeschlossen Nicht angeschlossen RS-232-Anschluss: 9-Pin Mini-DIN weiblich 8 9 7 6 3 4 5 2 Pin-Nr. 1 2 3 4 Signal VCC RD SD EXIR 5 6 SG ERX 7 8 9 RS CS ETX 1 Name I/O +3.3V (Reserviert) Ausgabe Daten empfangen Eingabe Daten senden Ausgabe Detektor der Optionseinheit Eingabe (Reserviert) Signalgrund IR-Signalempfang von Eingabe IR-Verstärker (Reserviert) Sendeanfrage Ausgabe Sendebereit Eingabe IR Signal übetragen Ausgabe (Reserviert) Referenz Nicht angeschlossen interner Stromkreisanschluss interner Stromkreisanschluss Nicht angeschlossen interner Stromkreisanschluss Nicht angeschlossen Nicht angeschlossen Nicht angeschlossen Nicht angeschlossen 9-Pin D-Sub männlicher Anschluss des DIN-D-Sub-RS-232C-Adapter 1 6 Pin-Nr. 1 2 3 4 5 6 7 8 9 5 9 Signal CD RD SD ER SG DR RS CS CI Name I/O N Daten empfangen Daten senden N Signalgrund Datensatz bereit Sendeanfrage Sendebereit N Eingabe Ausgabe Ausgabe Eingabe Referenz icht angeschlossen interner Stromkreisanschluss interner Stromkreisanschluss icht angeschlossen interner Stromkreisanschluss Nicht angeschlossen interner Stromkreisanschluss interner Stromkreisanschluss icht angeschlossen RS-232C Kabel empfohlene Verbindung: 9-Pin-D-Sub weiblich 5 9 Pin-Nr. 1 2 3 4 5 6 7 8 9 1 6 Signal CD RD SD ER SG DR RS CS CI Pin-Nr. 1 2 3 4 5 6 7 8 9 Signal CD RD SD ER SG DR RS CS CI Hinweis • Je nach Systemlayout kann es nötig sein, Pin 4 und Pin 6 beim kontrollierenden Gerät (z. B. Computer) zu verbinden. PC Pin-Nr. 4 5 6 Projektor Pin-Nr. 4 5 6 USB-Anschluss: 4-Pin-B-Typ USB-Stecker 2 1 3 4 Pin-Nr. 1 2 3 4 Signal VCC USB– USB+ SG Name USB-Strom USB-Daten– USB-Daten+ Signalgrund 54 XG-C50X Abmessungen 11 9/16 (294) 3/16 (5,2) 1/16 15 3/8 (390) (1,5) 1/16 2 1/8 1 3/4 (54,5) (44,5) 3 1/8 (80) (15) 3 7/8 (98,8) 5 (126,5) 9/16 9 1/2 4 3/8 (111,75) 2 15/16 (75) (7,5) 5/16 4 15/16 (124,5) 2 11/16 (67,5) 55 ø 67,5 3 15/16 (100,5) (241,5) 4 1/8 (104) 8 7/16 (213,8) 1/8 (4) Einheiten: Zoll (mm) (1,5) XG-C50X AUSBAU WICHTIGER TEILE 1. Ausbau von Bodenfilter-Abdeckung und Lampeneinheit-Abdeckung 1-1. 1-2. 1-3. 1-4. Bodenfilter-Abdeckung abtrennen. Die Sperrschraube von der Lampeneinheit-Abdeckung lösen und die Lampeneinheit-Abdeckung abnehmen. Den Tragegriff herausziehen. Die mit * markierte Stelle auf der oberen Hälfte der Objektiv-Abdeckung drücken, um die Klaue zu lösen, und dann die obere Objektiv-Abdeckung entfernen. 1-5. Die untere Hälfte der Objektiv-Abdeckung entfernen. 2. Oberplatte und Rückplatte entfernen 2-1. Sechs Sperrschrauben (schwarz) und eine Sperrschraube (gelb) von der Oberplatte entfernen. 2-2. Die acht Sperrschrauben von der Rückplatte entfernen, und die Rückplatte abnehmen. 2-3. Langsam die Oberplatte anheben und den Steckverbinder von der Schlüssel-Leiterplatte abtrennen. Eine andere Schraube entfernen, und die Oberplatte abnehmen. Lampeneinheit-Abdeckung 1-2 1-4 Obere Hälfte der Objektiv-Abdeckung 1-3 1-1 Tragegriff 1-5 Untere Häfle der Objektiv-Abdeckung Oberplatte Bodenfilter-Abdeckung 2-2 2-3 Rückplatte 2-1 (Schwarz) 2-1 (Gelb) 56 XG-C50X 3. Entfernen der Leiterplatten 3-1. 3-2. 3-3. 3-4. Die zwei Sperrschrauben vom Lampenfassung-Winkel entfernen. Den Lampenfassung-Winkel abtrennen. Die Ballast-Einheit anheben. Den Steckverbinder abtrennen, und die Ballast-Einheit abtrennen. Die Sperrschraube von der Leiterplatten-Einheit-Abdeckung lösen und die Abdeckung abnehmen. Die drei Sperrschrauben vom Kühlgebläse entfernen, den Steckverbinder abtrennen, und die LeiterplattenBaugruppe abnehmen. 3-5. Die zwei Sperrschrauben vom Kühlgebläse entfernen, den Steckverbinder abtrennen, und das Kühlgebläse abnehmen. 3-6. Die Sperrschraube von der Masseklemme entfernen, den Steckverbinder abtrennen, und die AC-EingangLeiterplatte abnehmen. 4. Entfernen von Optik-Mechanismus, Gebläse-Leiterplatte, Strom-Leiterplatte und R/CEmpfänger-Leiterplatte. 4-1. Die sieben Sperrschrauben vom Optik-Mechanismus entfernen, und den Optik-Mechanismus herausnehmen. 4-2. Die Sperrschraube vom Kühlgebläse entfernen, den Steckverbinder abtrennen, und die KühlgebläseLeiterplatte abnehmen. 4-3. Die vier Sperrschrauben von der Strom-Leiterplatte entfernen, und die Strom-Leiterplatte abnehmen. 4-4. Die R/C-Empfänger-Leiterplatte herausnehmen. 3-5 3-4 3-4 Kühlgebläse Leiterplatten-Baugruppen 3-1 Ballast-Einheit 3-6 3-2 AC-Eingang-Leiterplatte 4-1 4-2 Kühlgebläse 3-3 Gebläse-Leiterplatte Leiterplatten-Baugruppen-Abdeckung 4-1 4-3 4-3 Strom-Leiterplatte R/C-Empfänger-Leiterplatte 57 XG-C50X RÜCKSTELLUNG DES LAMPEN-TIMERS 1 Das Netzkabel anschließen. 2 Den Lampen-Timer zurückstellen. • Das Netzkabel am Netzanschluss des Projektors anschließen. • Während , und auf dem Projektor gleichzeitig gedrückt wird, Netzanschluss ON auf dem Projektor drücken. • “LAMPE 100%” erscheint und zeigt damit an, dass der Lampen-Timer zurückgestellt ist. INPUT-Taste Netz-Taste (ON) ENTER -Taste Info • Stellen Sie sicher, dass Sie den LampenTimer nur nach dem Austausch der Lampe zurücksetzen. Wenn Sie den Lampen-Timer zurücksetzen und dieselbe Lampe weiterhin verwenden, könnte die Lampe beschädigt werden oder explodieren. UNDO -Taste ■ Die Warnleuchten auf dem Projektor weisen auf Fehlfunktionen im Projektor hin. ■ Falls ein Problem auftritt, leuchtet entweder die Temperaturwarn-Anzeige oder die LampenaustauschAnzeige rot auf und die Stromversorgung wird ausgeschaltet. Nach dem Ausschalten des Gerätes den unten aufgeführten Schritten folgen. Über die LampenaustauschAnzeige Netz-Anzeige LampenaustauschAnzeige TemperaturwarnAnzeige Die restliche Lebensdauer der Lampe sinkt auf 0%, wenn sie ungefähr 2.000 Stunden im “Stromsparmodus” bei der Option “ON” verwendet wurde oder nach ungefähr 1.500 Stunden im “Stromsparmodus” bei der Option “OFF” (siehe Seite 69). Wenn die restliche Lebensdauer der Lampe auf 6% oder weniger absinkt, wird “ ” auf dem Bildschirm in gelb eingeblendet. Wenn der Prozentsatz 0% wird, ändert “ ” auf “ ” (rot), worauf die Lampe und danach der Projektor automatisch ausgeschaltet werden. Gleichzeitig leuchtet die Lampenaustausch-Anzeige rot auf. Nachdem Sie zum vierten Mal versucht haben den Projektor einzuschalten, ohne dass die Lampe ausgetauscht wurde, kann der Projektor nicht mehr eingeschaltet werden. Über die Temperaturwarn-Anzeige Wenn der Projektor wegen Problemen bei der Aufstellung oder wegen Blockierens der Luftöffnungen zu warm wird, blinkt “ ” in der unteren linken Ecke des Bildes. Wenn die Temperatur weiter ansteigt, schaltet sich die Lampe aus und die Temperaturwarn-Anzeige blinkt; der Kühlventilator dreht sich für weitere 90 Sekunden und anschließend wird die Stromversorgung ausgeschaltet. Nachdem “ ” angezeigt wird, unbedingt die folgenden Maßnahmen durchführen. Wartungsanzeige Unnormal Normal TemperaturwarnAnzeige LampenaustauschAnzeige NetzAnzeige Aus Grün ein Grün blinkt, wenn die Lampe aktiviert ist. Symptom Problem Rot ein/ Strom aus Die Temperatur im Inneren des Gerätes ist zu hoch. Rot blinkt / Rot eingeschaltet Die Lampe muss • Restliche Lebensdauer der ausgetauscht Lampe sinkt auf 6% oder werden weniger ab. Rot ein/ Strom aus Die Lampe leuchtet nicht. Grün eingeschaltet / Rot blinkt Rot eingeschaltet Die Netz-Anzeige blinkt bei eingeschaltetem Projektor rot auf. Abhilfe • Belüftungsöffnungen blockiert. • Den Projektor an einem besser belüfteten Ort aufstellen. • Den Projektor einem von Sharp • Kühlventilator beschädigt • Interne Schaltkreise beschädigt autorisierten Händler für Projektoren oder dem Kundendienst zur Reparatur geben. • Luftfilter verstopft • Ersetzen Sie die Lampe. • Den Projektor einem von Sharp autorisierten Händler für Projektoren oder dem Kundendienst zur Reparatur oder zum Lampenaustausch geben. • Ausgebrannte Lampe • Lassen Sie beim Austausch der Lampe • Lampen-Schaltkreis beschädigt bitte die nötige Vorsicht walten. • Setzen Sie die Filterabdeckung sorgfältigein. • Die Filterabdeckung, die Abdeckung der Lampeneinheit • Sollte die Netzanzeige auch bei korrekt eingesetzter Filterabdeckung rot aufblinken, oder die Objektivkappe ist dann wenden Sie sich bitte an Ihren einen geöffnet. von Sharp autorisierten Händler für Projektoren oder anderen Kundendienste. 58 XG-C50X KURZBESCHREIBUNG DER OPTIK-EINHEIT Layout für richtige Einrichtung der optischen Komponenten und Teile (Draufsicht) Projektionslinse Relaislinse 3 L2 M5 Al-vergüteter Spiegel B M4 Al-vergüteter Spiegel R Fliegenauge-Objektiv (Ausgang) L1 Relaislinse 2 Fliegenauge-Objektiv (Eingang) L2 M3 Reflektor G Reflektor R M2 Reflektor B Relaislinse 1 Lichtquelle (Lampe) 59 XG-C50X Einstellen der Spiegel Diese Einstellung ist erforderlich, wenn optische Teile des Optik-Mechanismus ersetzt wurden. 1. Die Flachkabel von allen LCD-Platten abtrennen. 2. Die Lampe einschalten. 3. Ein Weißlichtbild projizieren und prüfen, ob ein Farbstich in einer Richtung vorhanden ist. Falls vorhanden, die Einstellhebel M2, M4 und M5 verwenden. 4. Die Einstellhebel-Sperrschrauben lösen, Einstellungen vornehmen, und die Sperrschrauben festziehen. Einstellhebel M5 Einstellhebel M4 Sperrschrauben Schraube A Sperrschrauben Sperrschrauben Einstellhebel M2 Schraube B Korrigieren von Farbabweichungen auf rein weißen Bildschirm beim Ersetzen der Lampe Falls Farbabweichungen rechts und links in einem rein weißen Bildschirm nach dem Ersetzen der Lampe vorgefunden werden, ist es erforderlich, die optische Achse der neuen Lampe nachzujustieren. Die folgenden Schritte ausführen. 1. Die Lampenabdeckung öffnen und die Schrauben A und B am Boden der Lampe lösen. 2. Mit einem Schraubenzieher o.ä. die U-förmige Rille im Fenster D in Pfeilrichtung bewegen. 3. Provisorisch die Schrauben A und B festziehen, die Lampenabdeckung schließen und den rein weißen Bildschirm auf Farbabweichungen prüfen. 4. Die obigen Schritte 1 und 2 wiederholen, bis keine Farbabweichungen vorliegen. Jetzt die Schrauben A und B festziehen. 5. Schließlich die Lampenabdeckung in der ursprünglichen Position befestigen. 60 XG-C50X Ersetzen der Prismen-Einheit 1. Die vier Sperrschrauben entfernen, und die Prismen-Einheit aus der Optik-Einheit nehmen. 2. Die Prismen-Einheit durch die neue ersetzen. Den obigen Schritt 1 in umgekehrter Reihenfolge ausführen. Hinweis: Auch wenn nur eine der LCD-Platten defekt ist, ist es erforderlich, die gesamte Prismen-Einheit zu ersetzen. Nicht nur die defekte LCD-Platte ersetzen. Unter den gegebenen Umständen bitte nicht den Displayteil des LCD berühren. LCD-Platte G LCD-Platte R Prismen-Einheit-Sperrschrauben LCD-Platte B Optik-Einheit 61 XG-C50X Freigabe der Systemsperre Das Gerät einschalten. Wenn die Systemsperre aktiviert wird, erscheint die System-Nullstellungsanzeige. Danach sind die folgenden Tasten in der vorgeschriebenen Reihenfolge zu betätigen. MENU → ENTER → ENTER → MENU → UNDO → UNDO → MENU Zuerst die MENU-Taste drücken, dann die verbleibenden Tasten innerhalb von 10 Sekunden betätigen. 62 XG-C50X ELEKTRISCHE EINSTELLUNG Nr. Einstellgegenstände Einstellbedingungen Einstellverfahren 1 Initialisieren von EEPROM 1. Die Betriebsstromversorgung einschalten (die Lampe leuchtet auf), und das System 15 Minuten lang warmlaufen lassen. 1. Die folgenden Einstellungen vornehmen. S2601 drücken, um auf Prozessmodus zu schalten, und S2 im SSS-Menü ausführen. Jetzt ist der EEPROM, ausgenommen für die PCSchnittstelleneinheit, initialisiert. Nicht S1 ausführen, oder die PCSchnittstelleneinheit selber wird initialisiert. (Die PC-Schnittstelleneinheit ist werkseitig eingestellt.) Zum Einstellen der PCSchnittstelleneinheit siehe Abschnitt "Einstellen der PC-Schnittstelleneinheit" auf der letzten Seite. 2 Einstellung der RGB1SchwarzpegelSignalamplitude 1. Die folgende Gruppe und die folgenden Gegenstände wählen. Gruppe: OUTPUT1 Gegenstand: G1-BLK, G1GAIN Für die Farbe R die Gegenstände R1-BLK und R1-GAIN wählen. Für die Farbe B die Gegenstände B1-BLK und B1-GAIN wählen. 2. Sicherstellen, dass die ProzesseinstellungFarbbalken angezeigt werden. 3. Für die Farbe G ein Oszilloskop an Stift (2) von P1301 anschließen. 4. Für die Farben R und B das Oszilloskop jeweils an Stift (1) von P1301 und Stift (3) von P1301 anschließen. 1. Den Gegenstand G1-GAIN wählen. Mit dem Steuerschalter am Gerät oder der betreffenden Taste an der Fernbedienung die Einstellung so einstellen, dass die Signalamplitude 4,0 Vs-s ±0,05 V beträgt. 2. Den Gegenstand G1-BLK wählen. Mit dem Steuerschalter am Gerät oder der betreffenden Taste an der Fernbedienung die Einstellung so einstellen, dass der Weiß-Weiß-Pegel 1,8 Vs-s ±0,1 V beträgt. 3. Gleichermaßen für die anderen Farben R und B verfahren. 1. Die folgende Gruppe und die folgenden Gegenstände wählen. Gruppe: OUTPUT2 Gegenstand: PSIG-H, PSIG-L Sicherstellen, dass die Einstellungen für PSIG-H und PSIG-L bei 64 bzw. 100 sind. 1. Die angezeigte PSIG-Wellenform erhalten. (Das XGA-Signal einspeisen.) 3 Einstellung von PSIG 63 ~ Die G1-Gegenstände sind mit den R1und B1-Gegenstände verknüpft. Wenn die Einstellung für G1-BLK geändert wurde, sind deshalb die Einstellungen für R1-BLK und B1-BLK gleichermaßen geändert. Wenn die Einstellung für G1-GAIN geändert wurde, sind deshalb die Einstellungen für R1GAIN und B1-GAIN gleichermaßen geändert. Zuerst die G1-Einstellungen vornehmen, und dann die Einstellungen für R1 und B1 nach Bedarf korrigieren. PSIG 2,5 V DC 5,6 V DC Die Einstellung von PSIG-H justieren. Masse Die Einstellung von PSIG-L justieren. XG-C50X Nr. Einstellgegenstände Einstellbedingungen Einstellverfahren 4 Prüfen der Abtasten-HalteImpulsphase 1. Das XGA-Mode 75-Hz Schwarz-Signal einspeisen. 2. Die folgende Gruppe und die folgenden Gegenstände wählen. Gruppe: OUTPUT3 Gegenstand: GCK-PHASE 1. Den festen Wert prüfen. Fester Wert: 6 5 Einstellung der RGBGegenspannung 1. Das GegenspannungEinstellsignal (XGA), wie von der Technischen Abteilung vorbereitet, einspeisen. 2. Die folgende Gruppe und die folgenden Gegestände wählen. Gruppe: OUTPUT3 Gegenstand: RC (R), GC (G), BC (B) 1. Mit dem Steuerschalter am Gerät oder der betreffenden Taste an der Fernbedienung die Einstellungen einstellen, um Flimmern zu minimieren. 2. Wenn die Ergebnisse in der Mitte und an beiden Seiten auf dem Bildschirm inkonsistent sind, die Einstellungen nachjustieren, um das gleiche Ergebnis an beiden Seiten zu erhalten. 6 Einstellung der RGB-GradationReproduktion 1. Das SMPTE-Mustersignal einspeisen. 2. Die folgende Gruppe und die folgenden Gegenstände wählen. Gruppe: OUTPUT1 Gegenstand: G1-BLK 1. Bestätigen, dass die 100% und 95% Weißgradation ebenso wie die 0% und 5% Schwarzgradation unterscheidbar sind. 2. Wenn die Weißgradation unterschiedlich aussieht, die Einstellung für G1-BLK fein justieren. 7 Einstellung des RGBWeißabgleichs 1. Das 32-StufenGrauskalasignal (XGA, 60 Hz) einspeisen. 2. Die folgende Gruppe und die folgenden Gegenstände wählen. Gruppe: OUTPUT1 Gegenstand: R1-BLK (R), B1-BLK (B) 1. Die Einstellungen R1-BLK and B1-BLK so justieren, dass sie die vorgeschriebene Gradationsbalance habe (entsprechend Standard-Monitor). 8 Einstellung von Video-AGC 1. Mit dem Steuerschalter am Gerät oder der betreffenden Taste an der Fernbedienung die Einstellung so einstellen, dass der Weiß-Schwarz-Pegel 0,72 Vs-s ±0,01 V beträgt. 9 Einstellung von Videohelligkeit/ Kontrast 1. Das NTSC 10-StufenGrauskalasignal einspeisen. 2. Die folgende Gruppe und und die folgenden Gegenstände wählen. Gruppe: VIDEO Gegenstand: AGC-ADJ 3. Das Oszilloskop zwischen TP4501 und TP4502 anschließen. 1. Das NTSC 100% FensterMustersignal einspeisen. 2. Die folgende Gruppe und die folgenden Gegenstände wählen. Gruppe: VIDEO Gegenstand: AUTO, PICTURE/BRIGHT 64 1. Das Signal einspeisen. Mit dem Steuerschalter am Gerät oder der betreffenden Taste an der Fernbedienung den Gegenstand AUTO wählen. Die Einstellung wird automatisch vorgenommen. 2. Dann die Einstellung von PICTURE/ BRIGHT justieren, bis das Signal bitfrei wird. XG-C50X Nr. Einstellgegenstände 10 Einstellung von Video-Farbton 1. Das Teil-Farbbalken-Signal einspeisen. 2. Die folgende Gruppe und die folgenden Gegenstände wählen. Gruppe: VIDEO1 Gegenstand: TINT 1. Den festen Wert bestätigen. Fester Wert: 128 11 Einstellung von NTSCFarbsättigung 1. Das Teil-Farbbalken-Signal einspeisen. 2. Die folgende Gruppe und die folgenden Gegenstände wählen. Gruppe: VIDEO Gegenstand: N-COLOR ~ Das Oszilloskop an Pin (1) von P1301 anschließen. 1. Den festen Wert bestätigen. Fester Wert: 54 (Zur Bezugnahme: 0,4 Vs-s) 1. Das PAL-Farbbalken-Signal einspeisen. 2. Die folgende Gruppe und die folgenden Gegenstände wählen. Gruppe: VIDEO Gegenstand: P-COLOR ~ Das Oszilloskop an Stift (1) von P1301 anschließen. 1. Den festen Wert bestätigen. Fester Wert: 51 (Zur Bezugnahme: 0,4 Vs-s) 1. Das SECAM-Farbbalken-Signal einspeisen. 2. Die folgende Gruppe und die folgenden Gegenstände wählen. Gruppe: VIDEO Gegenstand: S-COLOR ~ Das Oszilloskop an Stift (1) von P1301 anschließen. 1. Den festen Wert bestätigen. Fester Wert: 48 (Zur Bezugnahme: 0,6 Vs-s) 12 13 Einstellung der PALFarbsättigung Einstellung der SECAMFarbsättigung Einstellbedingungen Einstellverfahren 100% Weiß Rot 100% Weiß Rot 100% Weiß Rot 14 Einstellung des VideoWeißabgleichs 1. Das NTSC-TestbildröhrenMustersignal einspeisen. 2. Die folgende Gruppe und die folgenden Gegestnände wählen. Gruppe: VIDEO Gegenstand: V-R1-BLK, V-B1BLK 1. Mit dem Steuerschalter am Gerät oder der betreffenden Taste an der Fernbedienung die Einstellungen einstellen, die den gleichen Weißabgleich wie auf dem Standard-Monitor haben. 15 Einstellung der 1. Das 0%-Graumustersignal (480I) COMPO-Helligkeit einspeisen. 2. Die folgende Gruppe und die folgenden Gegenstände wählen. Gruppe: COMPO Gegenstand: G-BRIGHT 1. Das Signal an INPUT1 einspeisen. Die Einstellung so justieren, dass einige Bites auf dem Bildschirm fehlen. 65 XG-C50X Nr. Einstellgegenstände Einstellbedingungen Einstellverfahren 16 Einstellung von COMPO CBOffset und CROffset 1. Das Y-0% Helligkeit, Cb und Cr 0% Weißmuster-FarbdifferenzSignal (480I) einspeisen. 2. Die folgende Gruppe und die folgenden Gegenstände wählen. Gruppe: COMPO Gegenstand: AUTO 1. Das Signal einspeisen. Mit dem Steuerschalter am Gerät oder der betreffenden Taste an der Fernbedienung den Gegenstand AUTO wählen. Die Einstellung wird automatisch vorgenommen. 17 Einstellung von COMPOWeißabgleich 1. Das DTV-TestbildröhrenMustersignal einspeisen. 2. Die folgende Gruppe und die folgenden Gegenstände wählen. Gruppe: COMPO Gegenstand: CR-R1-BLK, C-B1BLK 1. Mit dem Steuerschalter am Gerät oder der betreffenden Taste an der Fernbedienung die Einstellungen einstellen, die den gleichen Weißabgleich wie auf dem Standard-Monitor haben. 18 Einstellung des RGBWeißabgleichs 1. Das RGB 50%-Graumustersignal einspeisen. 2. Die folgende Gruppe und die folgenden Gegenstände wählen. Gruppe: OUTPUT1 Gegenstand: S-R1-BLK, S-R1GAIN, S-G1-BLK, S-G1-GAIN, SB1-BLK, S-B1-GAIN 3. Den Helligkeitsmesser BM-5 und das Standard-Whiteboard bereit halten. 1. Sicherstellen, dass die Einstellung von S-R1-BLK die gleiche ist wie die von R1-BLK. Sicherstellen, dass die Einstellung von S-G1-BLK die gleiche ist wie die von R1-BLK. Sicherstellen, dass die Einstellung von S-B1-BLK die gleiche ist wie die von R1-BLK. Sicherstellen, dass die Einstellung von S-R1-GAIN die gleiche ist wie die von R1-GAIN. 2. Die Einstellungen von S-B1-GAIN und S-G1-GAIN so justieren, dass die Farbsättigung am Helligkeitsmesser wie folgt angezeigt wird. x: 313 ±7/1000 y: 350 ±10/1000 Teaching-Intervalle: 18 Helligkeit-einstellbare Richtung: Helligkeit höher durch höhere Einstellung (zu prüfen) Einstellpunkte: Dreidimensional (zu prüfen) Gradation 4 (zu prüfen) Gradation 5 (zu prüfen) Gradation 6 (zu prüfen) Andere Gradationen, nicht zu prüfenEinstellbare Farben: R, G und B einstellbar (zu prüfen) (2) Farbabweichung-Korrektur (Einstellung) C50 Bedingungen Einrichtung ( ) Korrekturverfahren-Einstellungen Gradation 7: 2. Korrekturwert mit niedrigerer Gradation zu verwenden. Gradation 6: 0. Korrektur mit Korrekturkoeffizient. Gradation 5: 0. Korrektur mit Korrekturkoeffizient. Gradation 4: 0. Korrektur mit Korrekturkoeffizient. Gradation 3: 1. Korrekturwert mit höherer Gradation zu verwenden. Gradation 2: 1. Korrekturwert mit höherer Gradation zu verwenden. Gradation 1: 4. Anfangswert zu verwenden. Gradation 0: 4. Anfangswert zu verwenden. Für das betreffende Modell den in (2) eingegebenen Namen verwenden, um die FarbabweichungKorrektur zu starten. Wenn das Gerät optische Eigenschaften hat, die sich von den Normaleigenschaften stark unterscheiden oder wenn es fehlende Farbabweichung-Linien aufweist, den Teaching-Vorgang für das betreffende Gerät ausführen. Seine spezifizierten Korrekturkoeffizienten bei der Einstellung verwenden. 66 XG-C50X Nr. Einstellgegenstände Einstellbedingungen Einstellverfahren 19 Prüfen und Nachjustieren des Weißabgleichs 1. Die Einstellbedingungen für jeden Gegenstand sind wie folgt: Für RGB-Eingang siehe Gegenstand 7. Für Video-Eingang siehe Gegenstand 13. Für COMPO-Eingang siehe Gegenstand 16. 1. Sicherstellen, dass der Weißabgleich so ist, wie beim Standardmonitor angegeben. Nur Nachjustierung in der Reihenfolge RGB-Eingang, VideoEingang und COMPO-Eingang verfahren. 20 Farbbezogene Leistung prüfen 1. Das Farbbalken-Signal empfangen. 1. L1 im Prozessmodus wählen. Die Leistung von Farbe und Farbton prüfen. 21 Die bildbezogene Leistung prüfen 1. Das Testbildröhren-Mustersignal empfangen. 1. L2 im Prozessmodus wählen. Bild, Helligkeit und Schärfe prüfen. 22 Die RGB-Leistung prüfen 1. Das RGB-Signal empfangen. 1. L4 im Prozessmodus wählen. Bild, Helligkeit, Rot, Blau, Takt, Phase, H-POS und V-POS prüfen. 23 Die AusschaltTimer-Funktion prüfen 24 Prüfen der Thermistor-Funktion 1. Den Thermistor mit einem Haarfön erhitzen. 1. Sicherstellen, dass die Temperatur angezeigt wird. 25 Automatische Sync-Funktion 1. Das Phasen-Prüfmustersignal empfangen. 1. Sicherstellen, dass Takt, Phase, HPOS und V-POS automatisch im Modus VGA/S-VGA/XGA eingestellt werden können. 26 Die USB-Leistung prüfen 1. Mit dem USB-Kabel das Gerät an einen PC anschließen. 1. Mit der Fernbedienung sicherstellen, dass Einspeise- und Rückführvorgänge auf dem Bildschirm des PC wirksam sind. 27 Werkseitige Einstellungen 1. OFF im Prozessmodus wählen. Sicherstellen, dass der AusschaltTimer mit 5-Minuten-Anzeige startet, 1 Minute für 1 Sekunde herunterzählt, und ausschalten, wenn 0 Minuten angezeigt wird. 1. Die folgenden Einstellungen vornehmen. Ziel / Prozesseinstellung / Fernbedienung-Einstellungen Nordamerika-Modelle: S4 "Werkseitige Einstellung 4" Inlandsmodelle: S5 "Werkseitige Einstellung 5" Andere Modelle: Nordmerika: S3 "Werkseitige Einstellung 3" 67 XG-C50X Einstellung der PC-Schnittstelleneinheit 1. Initialisieren von EEPROM 1) SW2801 drücken, um auf Prozessmodus zu schalten. 2) S1 im SSS-Menü ausführen. (Mit S1 wird die Platine alleine initialisiert. Nicht S2 ausführen, oder alle Justierdaten, ausgenommen die für PC-Schnittstelle, werden initialisiert. 3) Sicherstellen, dass die Programmversion "VER. XXX" im Menü SPECIAL die neueste ist. 2. Pegel-Einstellungen 2-1. Einstellen des Oszilloskops Den Oszilloskop-Bereich auf DC1V/div und Sµ S/div stellen. 2-2. Anschließen der PC-Schnittstelle 1) Das vorgeschriebene Kabel zwischen ANALOG OUTPUT (am Signalgenerator) und der Buchse DSUB (INPUT1 am Projektor) anschließen. 2) Den Eingangswähler des Projektors auf INPUT1 stellen. 3) Den Signalgenerator auf XGA-Modus stellen (1024x768, 60 Hz, 32-Stufen-Gradation). Außerdem die Ausgangsamplitude (zwischen schwarz und weiß) auf 700 mVs-s einstellen (terminiert mit 75 Ohm Impedanz). 4) Netzstrom einschalten. 2-3. Einstellgegenstände 1) Einstellung von RGB Treiber/Verstärkung (1) Das Fenster-Mustersignal einspeisen, das 100% und 0% Signale hat. (2) AUTO unter den A/D-Gegenständen im Prozessmodus wählen, und die Einstellungen vornehmen. 68 XG-C50X » Eingabe des Einstellprozeßmodus Es gibt die folgenden zwei Verfahren. » Den SW2001 an der Tastenplatinen-Einheit drücken. » Die folgenden Tasten in der vorgeschriebenen Reihenfolge betätigen. Netz→Einstell oben→Einstell unten→Einstell oben→Einstell unten→ENTER→ENTER→MENU » Einstellmodus-Prozessmenü Gruppe Adjust PC Image A/D Untergruppe Adjust RGB Image OUTPUT1 Adjust Panel Drive OUTPUT2 Adjust Commn Voltage OUTPUT3 Adjust Video Image VIDEO Adjust Component Image COMP 69 Gegenstand R-BRIGHT G-BRIGHT B-BRIGHT R-D B-D G-D AD-AUT R1-BLK R1-GAIN G1-BLK G1-GAIN B1-BLK B1-GAIN S-R1-BLK S-R1-GAIN S-G1-BLK S-G1-GAIN S-B1-BLK S-B1-GAIN PSIG-H PSIG-L RC GC BC GCK-PHASE PICTURE BRIGHT TINT N-COLOR P-COLOR S-COLOR AGC-CNT AGC-ADJ STAT-GAIN V-R1-BLK V-B1-BLK VIDEO-AUTO G-BRIGHT CB-OFFSET CR-OFFSET C-R1-BLK C-B1-BLK COMPO-AUTO XG-C50X Gruppe Process Mode Untergruppe LINE Initial Setting SSS Sample Pattern PATTERN Adjust CVIC CVIC Gegenstand L1 L2 L4 OFF TEMP OFF SENSOR CHECK TIME S1 S2 S3 S4 S5 RGB RGB[50] CROSS FOCUS STEP COLOR CHR PROGRESSIVE ENHANCE-VIDE ENHANCE-HDTV ENHANCE-RGB SCREEN NR PTG 70 MODE IP MDSW PTGSW C-TESTSW C-ILG-LY C-MOD-LY C-VE-LV ENH-PLUS ENH-MINUS DFC ENH-PLUS ENH-MINUS DFC MODE ENH-GAIN ENH-PLUS CUBIC-RGB CUBIC-VIDEO YNR-LEVEL YNR-K YNR-FSEL CNR-LEVEL CNR-K CNR-FSEL CNR-FILSW TBL-NO TESTSW ENABLE MV-F VDDYP XG-C50X Gruppe Adjust CVIC Untergruppe Adust Digital Convergence CONVER Vesion Cehck etc SPECIAL 71 Gegenstand CMS-HUE CMS-HUE-R CMS-HUE-Y CMS-HUE-G CMS-HUE-C CMS-HUE-B CMS-HUE-M CMS-SAT CMS-SAT-R CMS-SAT-Y CMS-SAT-G CMS-SAT-C CMS-SAT-B CMS-SAT-M CMS-VAL CMS-VAL-R CMS-VAL-Y CMS-VAL-G CMS-VAL-C CMS-VAL-B CMS-VAL-M DEGAMMA CC R-CNV-H G-CNV-H B-CNV-H R-CNV-V G-CNV-V B-CNV-V IPL IPL2 E2PROM ADR RD/WR USB-MODE XG-C50X FEHLERSUCHTABELLE Die Lampe leuchtet nicht auf. Netzschalter einschalten. Ist ein Entladegeräusch von der Lampe hörbar? Ja Ist die Lampe außerhalb der Fassung? Ja Die Lampe wieder in die Fassung bringen. Nein Nein Lampe wechseln. Nein Die Betriebsstromkreise prüfen. Läuft das Ballast-Kühlgebläse? Ja Liegt DC 280 V/400 V Spannung zwischen den CN704 Stecker-Stiften an? Nein Die Betriebsstromkreise prüfen. Ja Liegt 2 V oder höhere Spannung zwischen Stift (4) und (2) des Ballast-Steckers CN705 an? Nein Ist der Stecker CN705 abgetrennt? Yes Ja Wieder richtig in die Fassung bringen. Den Ballast ersetzen. 72 Nein Den Mikroprozessor und seine Peripheriekreise prüfen. XG-C50X FEHLERSUCHTABELLE (Fortsetzung) Die Netzstufe prüfen. Kein Spannungsausgang an CN708. Nein Die Ausgang-Leiterplatteneinheit prüfen. Ja Welche Ausgangsspannungsleitung Andere T703, IC703, IC705, IC706 und ihre ist nicht in Ordnung? Peripheriekreise prüfen. BU5.3V Liegt AC-Spannung (90-264 V) über dem Stecker CN701 an? Nein CN701 oder Netz-kabel prüfen. Ja Liegt AC-Spannung (90-264 V) über dem Stecker CN706 an? Ja Ja Ist der Widerstand R775 offen? Nein Nein Die Netzstufe ersetzen. Ja IIst die Sicherung F701 offen? F701 ersetzen. Nein Ist der Widerstand R702 offen? Ja R702 ersetzen. Nein Ist der Bimetall-Schalter offen? Ja Die rote Taste am Bimetall drücken. Nein Die Einlasseinheit ersetzen. 73 R775 ersetzen. XG-C50X FEHLERSUCHTABELLE (Fortsetzung) Kein Audio-Ausgang Wird das Audio-Signal vom Emitter Nein von Q306 ausgegeben? P301 und seine Peripheriekreise prüfen. Ja Wird das Signal an Stift (2) und (15) Nein von IC303 angelegt? IC303 und seine Peripheriekreise prüfen. Ja Wird das Signal an Stift (12) und (5) Nein oder Stift (3) und (13) von IC302 angelegt? IC302 und seine Peripheriekreise prüfen. Ja Wird das Signal von Stift (14) und (15) oder Stift (16) und (17) von P3102 ausgegeben? Nein Q304 und Q305 und ihre Peripheriekreise prüfen. Ja Wird das Signal an Stift (14) und (15) oder Stift (16) und (17) von SC102 angelegt? Nein Den Anschluss zwischen P3102 und SC3102 prüfen. Ja J431, J421 und ihre Peripheriekreise prüfen. 74 XG-C50X FEHLERSUCHTABELLE (Fortsetzung) Das Video-System prüfen. Leuchtet die Lampe? Nein Zu "Die Lampe leuchtet nicht auf" gehen. Ja Ist vorgeschriebene Spannung an EA-Steckern? Nein Stromkreis und seine Teile prüfen. Ja Wird das Video-Signal an Stift (23) von P3102 angelegt? Nein Den Videoanschluss und seine Peripheriekreise prüfen. Nein IC4502 und seine Peripheriekreise prüfen. Nein IC4505 und seine Peripheriekreise prüfen. Nein Q4501 und seine Peripheriekreise prüfen. Ja Wird das Audio-Signal von Stift (7) von IC4502 ausgegeben? Ja Wird das Signal von Stift (5) von IC4505 ausgegeben? Ja Wird das Signal an Stift (72) von P8002 angelegt? Ja Zum Abschnitt "Prüfen der PC-Schnittstelleneinheit" gehen. 75 XG-C50X FEHLERSUCHTABELLE (Fortsetzung) Prüfen des S-Video-Systems. Nein Leuchtet die Lampe? Zu "Die Lampe leuchtet nicht auf" gehen. Ja Ist vorgeschriebene Spannung an Nein EA-Steckern? Stromkreis und seine Teile prüfen. Ja Wird das Video-Signal an Stift (19) und (21) von P3102 angelegt? Nein Den Videoanschluss und seine Peripheriekreise prüfen. Nein IC4502 und seine Peripheriekreise prüfen. Nein Q4513 und seine Peripheriekreise prüfen. Nein Q4502 und seine Peripheriekreise prüfen. Ja Wird das Y-Signal von Stift (7) von IC4502 ausgegeben? Ja Wird das C-Signal vom Emitter von Q4513 ausgegeben? Ja Wird das Signal an Stift (72) und (73) von P8002 angelegt? Ja Zum Abschnitt "Prüfen der PC-Schnittstelleneinheit" gehen. 76 XG-C50X FEHLERSUCHTABELLE (Fortsetzung) Prüfen des RGB-Signals. Werden die RGB-Signale von Stift (16), (18) und (20) von IC3101 ausgegeben? Nein IC3101 und seine Peripheriekreise prüfen. Ja Werden die Signale von Stift (26), (28) Nein und (30) von P3102 ausgegeben? SC3102 und P3102 und ihre Peripheriekreise prüfen. Ja Werden die Signale an Stift (1), (5) und (25) angelegt? Nein Q2419 und Q2420 und ihre Peripheriekreise prüfen. Nein IC2401, Q2401, Q2402 und Q2404 und ihre Peripheriekreise prüfen. Nein Zum Abschnitt "Prüfen der PC-Schnittstelleneinheit" gehen. Nein IC1101, IC1102, IC1201, IC1202, I C1301 und IC1302 und ihre Peripheriekreise prüfen. Ja Werden die Signale an Stift (54), (58) und (62) angelegt? Ja Werden die Signale von Stift (45)(54), Stift (57)-(66) und Stift (69)(78) von P8001 ausgegeben? Ja Werden die Signale an IC1101, IC1102, IC1201, IC1202, IC1301 und IC1302 angelegt? Ja Werden die Signale an SC1101, SC1201, SC1301 angelegt? Ja Den Anschluss der LCD-Platten prüfen. Wenn Videosignal und OSD ebenfalls nicht gezeigt werden, die LCD-Platten ersetzen. 77 XG-C50X FEHLERSUCHTABELLE (Fortsetzung) Prüfen des RGB-Sync. Wird die Sync an Stift (2) und (4) von SC3102 angelegt? Nein IC3152, IC3153, IC3154 und IC3151 und ihre Peripheriekreise prüfen. Ja Werden die Signale an Stift (2), und Nein (12) von IC2404 angelegt? P3102 und seine Peripheriekreise prüfen. Ja Werden die Signale an Stift (63) und (66) von P8002 angelegt? Nein Ja Zum Abschnitt "Prüfen der PC-Schnittstelleneinheit" gehen. 78 IC2404 und seine Peripheriekreise prüfen. XG-C50X FEHLERSUCHTABELLE für PC I/F EINHEIT Überprüfen der PC-Platine 0 Wird das Benutzermenü angezeigt? Nein Die Bildschirmanzeige überprüfen. Den RGB-Eingang überprüfen. Den Komponenteneingang überprüfen. Den Videoeingang überprüfen. Ende 79 Ja XG-C50X FEHLERSUCHTABELLE für PC I/F EINHEIT (Fortsetzung) Überprüfen der Bildschirmanzeige Wird das Benutzermenü normalerweise durch die MENUTaste angezeigt? Ja Die Bildschirmanzeige ist normal. Nein Das Prozeßmenü eingeben und PATTERN anwählen. Danach das COLOR-Muster wählen. Die Farbe der Bildschirmanzeige normal? Nein Das DLP-System im ProzeßEinstellmodus einstellen. Ja 0 Die STEP-Signalwahl durchführen. Ist das STEP-Signal normal? Ja Die Bildschirmdaten andern. Nein 0 Ist das Signal mit dem STEPSignal kompatible (am TL106 bis TL111 vorhanden). Nein Ja Zu “Überprüfen von GA4 und seine zugehörigen Komponenten” weitergehen. Die Bildschirmdaten ändern. 80 Der IC8025 ist defekt. XG-C50X FEHLERSUCHTABELLE für PC I/F EINHEIT (Fortsetzung) Überprüfen des RGB-Eingangs Das RGB-Signal (SynchronisationstypAnalogsignal) dem INPUT 1 zuführen. 1 INPUT 1 mit der Gerätetaste bzw. mit der Fernbedienung anwählen. 2 Erscheint das Bild? Nein Zu “Bestätigen des Videoeingangs” weitergehen. Ja Zu “Überprüfen des Synchronisationssignals” weitergehen. Nein Zu “Überprüfen des RGBSignals” weitergehen. Ja Ist das Bild gestört? Nein 3 Erscheinen die drei Farben R, G und B? Ja Den AUTOSYNC-Prozeß ausführen. Erscheinen die Bildumrisse scharf? Nein Ja Liegt eine Störung im VertikalStreifenmuster vor? Ja Nein Ende 81 IC8013, IC8025 oder seine zugehörigen Komponenten sind defekt. XG-C50X FEHLERSUCHTABELLE für PC I/F EINHEIT (Fortsetzung) Bestätigung des Videoeingangs “Bestätigung der EingangssignalEinstellung” vornehmen. Liegt am C8070 ein Videosignal vor? Nein Liegt am stift (55) von SC8002 (B-to-Bker) ein Signal an? Ja Ja Defekt innerhalb des Signalverlaufs. Die Kondensatoren und Widerstände zwischen dem SC8002 und IC8013 überprüfen. Zu “Überprüfen des Synchronisationssignals” weitergehen. IC8025 oder IC8013 sind defekt. Die Signalquelle bzw. der Stecker sind defekt. Bestätigung der EingangssignalEinstellung Wurde das Eingangsmenü korrekt angewählt? Nein Das Eingangsmenü richtig einstellen. Ja 2 Sind die Stecker richtig angeschlossen? Nein Die Stecker ordnungsgemäß anschließen. Ja 1 Ende 82 Nein XG-C50X FEHLERSUCHTABELLE für PC I/F EINHEIT (Fortsetzung) Überprüfen des Synchronisationssignals Liegt am Stift (11) von IC8363 ein Vertikal- Synchronisationssignal an? Ja Nein Liegt am Stift (5) von IC8363 ein Horizontal- Synchronisationssignal an? Ja Nein Bestätigung der EingangssignalEinstellung vornehmen. R997, R996, SC8002 oder ihre zugehörigen Komponenten sind defekt. Liegt am TL8131 ein VertikalSynchronisationssignal an? Nein Ja Liegt am TL8130 ein HorizontalSynchronisationssignal an? Nein IC8363 ist defekt. Ja Sind das Vertikal- und das Horizontal-Synchronisationssignal korrekt abgestimmt? Ja Das Synchronisationssignal ist normal. Ende der Überprüfung. Nein Liegt der geeignete Signalgenerator (Eingangsquelle) vor? Nein Die Signalquelle richtig einstellen. Ja 2 R9697, R996, SC8002 oder ihre zugehörigen Komponenten sind defekt. 83 XG-C50X FEHLERSUCHTABELLE für PC I/F EINHEIT (Fortsetzung) Überprüfen der R-, G- und BSignale Ist der Signaltyp auf RGB eingestellt? Nein Ja Den Signaltyp auf RGB einstellen. Den Prozeßmodus einstellen. R, G und B einzeln auf dem Mustermenü anwählen. Zu “Überprüfen von GA4 und seine zugehörigen Komponenten” weitergehen. Für das Überprüfen des Eingangssignals den Signalgeber auf das Abstufungssignal einstellen. TL8169, TL8170 und TL8180 mit dem Oszilloskop überprüfen. (MSB-Bit nach der A/DWandlung) Liegen bestimmte Signale an TL8169, TL8170 und TL8180 an? Nein Werden C8062, C8070 und C8078 Signale zugeführt? Ja Der IC8025 und seine zugehörigen Komponenten sind defekt. Nein Ja Der IC8013 und seine zugehörigen Komponenten sind defekt. 84 Zu “Bestätigen des Videoeingangs” weitergehen. XG-C50X FEHLERSUCHTABELLE für PC I/F EINHEIT (Fortsetzung) Überprüfen von GA4 und seine zugehörigen Komponenten R, G und B einzeln auf dem Mustermenü anwählen. Wird das Bild korrekt in R-, Gund B-Signalen ausgegeben? Ja Das Überprüfen von GA4 und der zugehörigen Komponenten ist beendet. Nein Die Stifte (54), (66) und (78) von SC8001 mit dem Oszilloskop messen. Diese Signale entsprechen MSB von B/G/R. Stimmen die angewählten Signale im Mustermenü mit den durch das Oszilloskop gemessenen Signalen überein? Ja Die Ausgangs-Platine ist defekt. Nein Wird das Taktsignal dem Stift (40) und (42) von SC8001 zugeführt? Nein Liegt ein Taktsignal von 37,5 MHz am TL8114 an? Ja Ja Nein Der IC8029 ist defekt. Liegt ein Taktsignal von 37,5 MHz am FL8110 an? Nein Ja Der X8005 ist defekt. TL8106, TL8107, TL8108, TL8109, TL8110 und TL8111 mit dem Oszilloskop überprüfen. Stimmen die angewählten Signale im Mustermenü mit den durch das Oszilloskop gemessenen Signalen überein? Der IC8025 ist defekt. Nein Der IC8025 ist defekt. Ja Der IC8029 ist defekt. 85 XG-C50X FEHLERSUCHTABELLE für PC I/F EINHEIT (Fortsetzung) Überprüfen des Komponenteneingangs (außer 480I) Das Komponentensignal dem INPUT 1 zuführen. INPUT 1 mit der Gerätetaste bzw. mit der Fernbedienung anwählen. Erscheint das Bild? Nein Zu “Überprüfen des SOGSchaltkreises” weitergehen. Ja 4 Ist die Farbe normal? Nein Ist der Signaltyp auf die Komponente eingestellt? Nein Ja Den Signaltyp auf die Komponente einstellen. Die Prozeß-Einstellung ausführen. 4 Erscheinen die Bildumrisse scharf? Nein IC8013 oder IC8025 ist defekt. Ja Das Komponentensignal ist normal. Ende. 86 XG-C50X FEHLERSUCHTABELLE für PC I/F EINHEIT (Fortsetzung) Überprüfen des SOG-Schaltkreises Den Stift (2) von IC8365 mit dem Oszilloskop überprüfen. Wird das Farbbildsignal mit dem korrekten Timing reproduziert? Ja Der SOG-Schaltkreis ist normal. Ende. Nein C8070 mit dem Oszilloskop überprüfen. Liegt ein Y-Signal (einschl. Synchronisationssignal) vor? Nein Ja Der SOG-SynchronsignalTrennschaltkreis (Eingangsplatine) ist defekt. 87 Zu “Bestätigung der Eingangssignal-Einstellung” weitergehen. XG-C50X FEHLERSUCHTABELLE für PC I/F EINHEIT (Fortsetzung) Überprüfen des Videoeingangs Das Farbbildsignal dem INPUT 3 zuführen. INPUT 1 mit der Gerätetaste bzw. mit der Fernbedienung anwählen. 5 Erscheint das Bild? Zu “Überprüfen des VideoSynchronsignals” weitergehen. Nein Ja Bestehen irgendwelche Bildstörungen? Ja Nein Zu “Überprüfen des VideoSynchronsignals” weitergehen. Die Prozeß-Einstellung ausführen? Nein Ist die Farbe normal? 5 Ja Der Videoeingang ist normal. Ende. Wird das Videosignal dem C8141 zugeführt? Nein Liegt am R8114 das spezifizierte Signal an? Ja Ja Der Q8002 und seine zugehörigen Komponenten sind defekt. Das Taktsignal von IC8015 durch FL8114 überprüfen. Ist das Taktsignal normal? Nein Nein Der IC8015 ist defekt. Ja Zu “Überprüfen des VideoSynchronsignals” weitergehen. Der IC8025 und seine zugehörigen Komponenten sind defekt. 88 Die Eingangsplatine ist defekt. XG-C50X FEHLERSUCHTABELLE für PC I/F EINHEIT (Fortsetzung) Überprüfen des VideoSynchronsignals Den Stift (10) von IC8363 mit dem Oszilloskop überprüfen. (Überprüfen des Vertikal-Synchronsignals) Ist das Vertikal-Synchronsignal normal? Nein Ja Den Stift (6) von IC8363 mit dem Oszilloskop überprüfen. (Überprüfen des VertikalSynchronsignals) Ist das Horizontal-Synchronsignal normal? Nein Zu “Bestätigung der Eingangssignal-Einstellung” weitergehen. Nein Der IC8015 und seine zugehörigen Komponenten sind defekt. Nein Der IC8015 und seine zugehörigen Komponenten sind defekt. Ja Werden das HorizontalSynchronsignal und das VertikalSynchronsignal an TL8130 und TL8131 ausgegeben? Ja Liegt am FL8114 ein bestimmtes Taktsignal (13,5 MHz) an? Ja Ende 89 XG-C50X CHASSIS LAYOUT/CHASSIS-ANORDNUNG H G F E D C B A 1 2 3 90 4 5 6 7 8 9 10 11 91 12 XG-C50X BLOCK DIAGRAM/BLOCKCHALTBILD H G F E D C B A 1 2 3 92 4 5 6 7 8 9 10 11 93 12 XG-C50X OVERALL WIRING DIAGRAM/GESAMTSCHALTPLAN H G F E D C B A 1 2 3 94 4 5 6 7 8 9 10 11 95 12 XG-C50X DESCRIPTION OF SCHEMATIC DIAGRAM BESCHREIBUNG DES SCHEMATISCHEN SCHALTPLANS VOLTAGE MEASUREMENT CONDITION: SPANNUNGSMESSUNGEN: 1. Voltages at test points are measured at the supply voltage of AC 230V. Signals are fed by a colour bar signal generator for servicing purpose and the above voltages are measured with a 20k ohm/V tester. 1. Spannungen an den Prüfpunkten werden bei einer Netzspannung von 230V gemessen, Signale werden für die Wartung mit einem Farbbalken-Signal generator zugeführt, und Spannungen werden mit einem Meßinstrument (20 kΩ/V) ermittelt. WAVEFORM MEASUREMENT CONDITION: SIGNALFORMMESSUNGEN: 1. Waveforms at test points are observed at the supply voltage of AC 230V. Signals are fed by a colour bar signal generator for servicing purpose. 1. Die Wellenformen an den Testpunkten werden bei einer Netzspannung von 230V verfolgt. Signale werden für die Wartung mit einem Farbbalken-Signal generator zugeführt. INDICATION OF RESISTOR & CAPACITOR: BEZEICHNUNG DES WIDERSTANDS UND KONDENSATORS: RESISTOR 1. The unit of resistance “Ω” is omitted. (K=kΩ=1000 Ω, M=MΩ). 2. All resistors are ± 5%, unless otherwise noted. (J= ± 5%, F= ± 1%, D= ± 0.5%) 3. All resistors are 1/16W, unless otherwise noted. 4. All resistors are Carbon type, unless otherwise noted. W : Cement C : Solid S : Oxide Film T : Special N : Metal Coating CAPACITOR 1. All capacitors are µF, unless otherwise noted. (P=pF=µµF). 2. All capacitors are 50V, unless otherwise noted. 3. All capacitors are Ceramic type, unless otherwise noted. (ML): Mylar (TA): Tantalum (PF): Polypro Film (ST): Styrol WIDERSTAND 1. Die Widerstandseinheit “Ω” wird weggelassen. (K=kΩ=1000 Ω, M=MΩ). 2. Alle Widerstände haben ± 5%, sofern nicht anders angegeben. (J= ± 5%, F= ± 1%, D= ± 0.5%) 3. Alle Widerstände haben 1/16W, sofern nicht anders angegeben. 4. Alle Widerstände sind Kohletyp, sofern nicht anders angegeben. W : Zement C : Fest S : Oxidefilm T : Spezial N : Metallüberzug KONDENSATOR 1. Die Kapazitätseinheit ist µF, sofern nicht anders angegeben. (P=pF=µµF). 2. Alle Kondensatoren haben 50V, sofern nicht anders angegeben. 3. Alle Kondensatoren sind Keramiktyp, sofern nicht anders angegeben. (ML): Mylar (TA): Tantal (PF): Polyprofilm (ST): Styrol CAUTION: This circuit diagram is original one, therefore there may be a slight difference from yours. ACHTUNG: bei diesem Schaltplan handelt es sich um den ursprünglichen. Esönnen daher geringfügige Unterschiede zu dem lhrem bestehen. SAFETY NOTES: 1. DISCONNECT THE AC PLUG FROM THE AC OUTLET BEFORE REPLACEING PARTS. 2. SEMICONDUCTOR HEAT SINKS SHOULD BE REGARDED AS POTENTIAL SHOCK HAZARDS WHEN THE CHASSIS IS OPERATING. SICHERHEITSANMERKUNGEN: 1. VOR DEM AUSWECHSELN VON TEILEN MUSS UNBEDINGT NETZSTECKER AUS DER NETZSTECKDOSE GEZOGEN WERDEN. 2. DIE WARMEABLEITER DER HALBLEITER SOLLTEN BEIM BETRIEB DES CHASSIS ALS MÖGLICHE URSACHEN VON GEFÄHRLICHEN ELEKTRISCHEN SCHLÄGEN BETRACHTET WERDEN. IMPORTANT SAFETY NOTICE: PARTS MARKED WITH “ å ( ) ARE IMPORTANT FOR MAINTAINING THE SAFETY OF THE SET. BE SURE TO REPLACE THESE PARTS WITH SPECIFIED ONES FOR MAINTAINING THE SAFETY AND PERFORMANCE OF THE SET. WICHTIGE SICHERHEITSANMERKUNGEN: MIT “å ( )BEZEICHNETEN TEILE SIND BESONDERS WICHTIG FÜR DIE AUFRECHTERHALTUNG DER SICHERHEIT . BEIM WECHDIESER TEILE SOLLTEN DIE VORGESCHRIEBENEN TEILE IMMER VERWENDET WERDEN, UM SOWOHL DIE SICHERHEIT ALS AUCH DIE LEISTUNG DES GERÄTES AUFRECHTZUERHALTEN. 96 XG-C50X Ë R/C RECEIVER UNIT / FERNBEDIENUNGS-EINHEIT H G F E D C B A 1 2 3 4 97 5 6 XG-C50X Ë INPUT UNIT-1/2 / EINGANGS EINHEIT-1/2 H G F E D C B A 1 2 3 98 4 5 6 7 8 9 10 11 99 12 XG-C50X Ë INPUT UNIT-2/2 / EINGANGS EINHEIT-2/2 H G F E D C B A 1 2 3 100 4 5 6 7 8 9 10 11 101 12 XG-C50X Ë OUTPUT UNIT-1/8 / AUSGANGSEINHEIT-1/8 H G F E D C B A 1 2 3 102 4 5 6 7 8 9 10 11 103 12 XG-C50X Ë OUTPUT UNIT-2/8 / AUSGANGSEINHEIT-2/8 H G F E D C B A 1 2 3 104 4 5 6 7 8 9 10 11 105 12 XG-C50X Ë OUTPUT UNIT-3/8 / AUSGANGSEINHEIT-3/8 H G F E D C B A 1 2 3 106 4 5 6 7 8 9 10 11 107 12 XG-C50X Ë OUTPUT UNIT-4/8 / AUSGANGSEINHEIT-4/8 H G F E D C B A 1 2 3 108 4 5 6 7 8 9 10 11 109 12 XG-C50X Ë OUTPUT UNIT-5/8 / AUSGANGSEINHEIT-5/8 H G F E D C B A 1 2 3 110 4 5 6 7 8 9 10 11 111 12 XG-C50X Ë OUTPUT UNIT-6/8 / AUSGANGSEINHEIT-6/8 H G F E D C B A 1 2 3 112 4 5 6 7 8 9 10 11 113 12 XG-C50X Ë OUTPUT UNIT-7/8 / AUSGANGSEINHEIT-7/8 H G F E D C B A 1 2 3 114 4 5 6 7 8 9 10 11 115 12 XG-C50X Ë OUTPUT UNIT-8/8 / AUSGANGSEINHEIT-8/8 H G F E D C B A 1 2 3 116 4 5 6 7 8 9 10 11 117 12 XG-C50X Ë KEY UNIT / SCHLÜSSELEINHEIT H G F E D C B A 1 2 3 118 4 5 6 7 8 9 10 11 119 12 XG-C50X Ë FAN UNIT / GEBLÄSE-HINHEIT H G F E D C B A 1 2 3 120 4 5 6 7 8 9 10 11 121 12 XG-C50X Ë AC INLET and POWER UNIT / AC EINGANGS-und NETZ-EINHEIT H G F E D C B A 1 2 3 122 4 5 6 7 8 9 10 11 123 12 XG-C50X Ë PC I/F UNIT-1/7 / PC-I/F-EINHEIT-1/7 H G F E D C B A 1 2 3 124 4 5 6 7 8 9 10 11 125 12 XG-C50X Ë PC I/F UNIT-2/7 / PC-I/F-EINHEIT-2/7 H G F E D C B A 1 2 3 126 4 5 6 7 8 9 10 11 127 12 XG-C50X Ë PC I/F UNIT-3/7 / PC-I/F-EINHEIT-3/7 H G F E D C B A 1 2 3 128 4 5 6 7 8 9 10 11 129 12 XG-C50X Ë PC I/F UNIT-4/7 / PC-I/F-EINHEIT-4/7 H G F E D C B A 1 2 3 130 4 5 6 7 8 9 10 11 131 12 XG-C50X Ë PC I/F UNIT-5/7 / PC-I/F-EINHEIT-5/7 H G F E D C B A 1 2 3 132 4 5 6 7 8 9 10 11 133 12 XG-C50X Ë PC I/F UNIT-6/7 / PC-I/F-EINHEIT-6/7 H G F E D C B A 1 2 3 134 4 5 6 7 8 9 10 11 135 12 XG-C50X Ë PC I/F UNIT-7/7 / PC-I/F-EINHEIT-7/7 H G F E D C B A 1 2 3 136 4 5 6 7 8 9 10 11 137 12 XG-C50X H PRINTED WIRING BOARD ASSEMBLIES LEITERPLATTENINHEITIN G F E D C B POWER Unit (Side-A) NETZ-Einheit (Seite-A) A 1 2 3 4 138 5 6 XG-C50X H G F E D C B POWER Unit (Side-B) NETZ-Einheit (Seite-B) A 1 2 3 4 139 5 6 XG-C50X H G F E D C B A INPUT Unit (Side-A) EINGANGS-Einheit (Seite-A) 1 2 3 4 140 5 6 XG-C50X H G F E D C B A INPUT Unit (Side-B) EINGANGS-Einheit (Seite-B) 1 2 3 4 141 5 6 XG-C50X H G F E D C B A OUTPUT Unit (Side-A) AUSGANGS-Einheit (Seite-A) 1 2 3 4 142 5 6 XG-C50X H G F E D C B A OUTPUT Unit (Side-B) AUSGANGS-Einheit (Seite-B) 1 2 3 4 143 5 6 XG-C50X H G F E D C B A PC I/F Unit (Side-A) PC I/F-Einheit (Seite-A) 1 2 3 4 144 5 6 XG-C50X H G F E D C B A PC I/F Unit (Side-B) PC I/F-Einheit (Seite-B) 1 2 3 4 145 5 6 XG-C50X H R/C RECEIVER Unit (Wiring Side) FERNBEDIENUNGS-Einheit (Leiterbahnseite) G F E AC INLET Unit (Wiring Side) AC-EINGANGS-Einheit (Leiterbahnseite) D C B KEY Unit (Wiring Side) SCHLÜSELL-Einheit (Leiterbahnseite) A 1 2 3 4 146 5 6 XG-C50X H G F E FAN Unit (Side-A) GEBLÄSE-Einheit (Seite-A) D C B A FAN Unit (Side-B) GEBLÄSE-Einheit (Seite-B) 1 2 3 4 147 5 6 XG-C50X Ref. No. Part No. ★ Description PARTS LIST Code Ref. No. ★ Part No. Description Code ERSATZTEILLISTE PARTS REPLACEMENT AUSTAUSCH VON TEILEN Parts marked with "å" are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set. Ersatzteile, die besondere Sicherheitseigenschften haben, sind in dieser Anleitung markiert. Elektrische Komponenten mit solchen Eigenshaften sind in den Ersatzteil durch "å" gekenn-zeichnet. Der Gebrauch von Ersatzteilen, die nicht deselben Sicherheitseigenschaften haben wie die vom Hersteller empfohlenen ud in der Bedienungsanleitung angegebenen, können zur Ursache von Blitzeinschlägen, Bränden und anderen Gefahren werden. "HOW TO ORDER REPLACEMENT PARTS" To have your order filled promptly and correctly, please furnish the following informations. "WIE MAN ERSATSTEILE BESTELLT" in USA: 1. MODEL NUMBER 2. REF. NO. 3. PART NO. 4. DESCRIPTION 5. CODE 6. QUANTITY Damit Ihre Bestellung promt und korrekt ausgeführt wird, geben Sie bitte folgende Informationen. 1. MODELL NR. 3. ERSATZTEIL NR. 5. KODE Contact your nearest SHARP Parts Distributor. For location of SHARP Parts Distributor, Please call Toll-Free; 1-800-BE-SHARP 2. REF. NR. 4. BESCHREIBUNG 6. QUANTITÄT in CANADA: Contact SHARP Electronics of Canada Limited Phone (416) 890-2100. ★ MARK: SPARE PARTS-DELIVERY SECTION Ref. No. Part No. ★ Description ★ MARKIERUNG : ERSATZTEILE-LIEFERUNG Code Ref. No. ★ Part No. Description Code DUNTKB170DE01 LCD PANELS INPUT UNIT INTEGRATED CIRCUITS NOTE: THE PARTS HERE SHOWN ARE SUPPLIED AS AN ASSEMBLY BUT NOT INDEPENDENTLY. RLCDPA007WJZZ – LCD Module Unit, Red — RLCDPA008WJZZ – LCD Module Unit, Green — RLCDPA009WJZZ – LCD Module Unit, Blue — NOTE: LCD PANEL SHOULD CORRESPOND BY PRISM UNIT REPLACEMENT IN THE FIELD. (Refer to page 18.) CMiR-A004WJ01 J Prism Unit IC3001 IC3051 IC3101 IC3102 IC3151 IC3152 IC3153 IC3154 IC3602 IC3701 VHi24LC21//-1Y VHi24LC21//-1Y VHiAD8185++-1Y VHiLM2664++-1Y RH-iX2242CEZZY VHiTC7W125U-1Y VHiT7WT240U-1Y VHiT7WT240U-1Y VHiUPD4721G-1Y RH-iXA178WJZZY Q3151 Q3701 Q3702 Q3703 VSDTC144EUA-1Y VSBSS84++++-1Y VSRN1905///-1Y VSRN1905///-1Y D401 D402 D3001 D3002 D3004 D3005 D3051 D3052 D3054 D3055 D3102 D3103 D3104 D3105 D3106 D3109 D3110 D3111 D3112 D3113 D3114 D3606 D3607 VHDMA3120WA-1Y VHDMA3120WA-1Y VHDKDS226//-1Y VHDKDS226//-1Y VHDKDS226//-1Y VHDKDS226//-1Y VHDKDS226//-1Y VHDKDS226//-1Y VHDKDS226//-1Y VHDKDS226//-1Y VHDKDS226//-1Y VHDKDS226//-1Y VHDKDS226//-1Y VHDKDS226//-1Y VHDKDS226//-1Y VHDKDS226//-1Y VHDKDS226//-1Y VHDKDS226//-1Y VHDKDS226//-1Y VHDKDS226//-1Y VHDKDS226//-1Y VHDMA3120WA-1Y VHDMA3120WA-1Y J J J J J J J J J J 24LC21T-I/SN 24LC21T-I/SN AD8185ARU LM2664M6X SN74LS14NS TC7W125FU TC7WT240FU TC7WT240FU UPD4721GS-GJG CY7C63413-PVCT AH AH AW AG AE AF AF AF AN AW TRANSISTORS PRINTED WIRING BOARD ASSEMBLIES (NOT REPLACEMENT ITEM) DUNTKB170DE01 DUNTKB171FE01 DUNTKB172DE01 DUNTKB173DE01 RUNTKA021WJZZ RUNTKA026WJZZ RDENCA011WJZZ CPCi-A002CE01 RDENCA012WJZZ – – – – – – – J J Input Unit Output Unit Key Unit R/C Receiver Unit AC Inlet Unit Fan Unit Power Unit PC I/F Unit Ballast Unit (Unit Replacement Item) — — — — — — — CW CB J J J J DTC144EUA BSS84 RN1905 RN1905 AB AE AB AB DIODES 148 J J J J J J J J J J J J J J J J J J J J J J J Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode AD AD AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AD AD XG-C50X Ref. No. ★ Part No. Description Code Ref. No. DUNTKB170DE01 INPUT UNIT(Continued) D3608 D3701 D3702 D3703 VHDDAN202K/-1Y VHDMA3120WA-1Y VHDMA3120WA-1Y VHDMA3120WA-1Y X3701 RFiLZ0003TAZZY J J J J Diode Diode Diode Diode AB AD AD AD PACKAGED CIRCUIT J Crystal AD FILTERS AND COILS FL402 FL403 FL431 FL3001 FL3002 FL3003 FL3051 FL3052 FL3053 FL3101 FL3102 FL3103 L3001 L3101 L3102 L3103 RFiLN0514CEZZY RFiLN0017TAZZY RFiLN0017TAZZY RFiLN0003TAZZY RFiLN0003TAZZY RFiLN0003TAZZY RFiLN0003TAZZY RFiLN0003TAZZY RFiLN0003TAZZY RFiLN0003TAZZY RFiLN0003TAZZY RFiLN0003TAZZY VP-1M100J1R6NY VP-1M100J1R6NY VP-1M100J1R6NY VP-1M100J1R6NY J J J J J J J J J J J J J J J J C421 C422 C431 C432 C441 C442 C3001 C3002 C3003 C3004 C3006 C3007 C3008 C3009 C3051 C3052 C3053 C3055 C3056 C3057 C3058 C3101 C3102 C3103 C3104 C3105 C3106 C3107 C3108 C3109 C3110 C3111 C3112 C3113 C3114 C3115 C3116 C3117 C3118 C3119 C3120 C3121 C3122 C3126 VCCCCY1HH101JY J VCCCCY1HH101JY J VCCCCY1HH101JY J VCCCCY1HH101JY J VCCCCY1HH101JY J VCCCCY1HH101JY J VCEAPF0JW476MY J VCKYCY1HB103KY J VCCCCY1HH330JY J VCCCCY1HH330JY J VCKYCY1EF104ZY J VCCCCY1HH180JY J VCCCCY1HH180JY J VCCCCY1HH180JY J VCKYCY1HB103KY J VCCCCY1HH330JY J VCCCCY1HH330JY J VCKYCY1EF104ZY J VCCCCY1HH180JY J VCCCCY1HH180JY J VCCCCY1HH180JY J VCKYCY1EF104ZY J VCEAPF1CW106MY J VCAAPC1AJ106MY J RC-KZ0416CEZZY J RC-KZ0416CEZZY J VCEAPF1CW226MY J VCEAPF1CW226MY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCE9PF0JW476MY J VCKYCY1HB103KY J VCKYCY1HB103KY J VCE9PF0JW476MY J VCKYCY1HB103KY J VCE9PF0JW476MY J VCKYCY1HB103KY J VCE9PF0JW476MY J VCKYCY1HB103KY J VCE9PF0JW476MY J VCKYCY1HB103KY J VCE9PF0JW476MY J VCCCCY1HH102JY J VCCCCY1HH102JY J Filter Filter Filter Filter Filter Filter Filter Filter Filter Filter Filter Filter Peaking 10µH Peaking 10µH Peaking 10µH Peaking 10µH AE AC AC AD AD AD AD AD AD AD AD AD AB AB AB AB 50V 50V 50V 50V 50V 50V 6.3V 50V 50V 50V 25V 50V 50V 50V 50V 50V 50V 25V 50V 50V 50V 25V 16V 10V 25V 25V 16V 16V 25V 25V 6.3V 50V 50V 6.3V 50V 6.3V 50V 6.3V 50V 6.3V 50V 6.3V 50V 50V Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Electrolytic Ceramic Ceramic Electrolytic Electrolytic Ceramic Ceramic Elect.(N.P) Ceramic Ceramic Elect.(N.P) Ceramic Elect.(N.P) Ceramic Elect.(N.P) Ceramic Elect.(N.P) Ceramic Elect.(N.P) Ceramic Ceramic C3151 C3152 C3153 C3154 C3155 C3156 C3602 C3603 C3604 C3605 C3606 C3607 C3704 C3705 VCKYCY1EF104ZY J VCEAPF1CW106MY J VCEAPF1CW106MY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCEAPF1HW225MY J VCEAPF1HW225MY J VCEAPF1HW225MY J VCEAPF1HW225MY J VCEAPF1HW225MY J VCKYCY1EF104ZY J VCEAPF1CW106MY J VCKYCY1EF104ZY J R402 R403 R404 R407 R408 R409 R410 R421 R431 R432 R441 R3002 R3003 R3004 R3006 R3007 R3008 R3009 R3010 R3011 R3012 R3013 R3014 R3052 R3053 R3054 R3056 R3057 R3058 R3059 R3060 R3061 R3062 R3063 R3064 R3103 R3104 R3105 R3106 R3107 R3108 R3109 R3111 R3113 R3115 R3117 R3119 R3151 R3152 R3155 R3156 R3157 R3158 R3159 R3160 R3161 R3162 R3163 R3164 VRS-TV1JD000JY VRS-TV1JD000JY VRS-TV1JD000JY VRS-TV1JD000JY VRS-TV1JD000JY VRS-TQ2BD750JY VRS-TQ2BD750JY VRS-TV1JD000JY VRS-TQ2BD750JY VRS-TV1JD000JY VRS-TV1JD000JY VRS-TW2ED750JY VRS-TW2ED750JY VRS-TW2ED750JY VRS-CY1JF473JY VRS-CY1JF103JY VRS-CY1JF101JY VRS-CY1JF101JY VRS-CY1JF101JY VRS-CY1JF101JY VRS-CY1JF102JY VRS-CY1JF271JY VRS-CY1JF271JY VRS-TW2ED750JY VRS-TW2ED750JY VRS-TW2ED750JY VRS-CY1JF473JY VRS-CY1JF103JY VRS-CY1JF101JY VRS-CY1JF101JY VRS-CY1JF101JY VRS-CY1JF101JY VRS-CY1JF102JY VRS-CY1JF271JY VRS-CY1JF271JY VRS-TW2ED750JY VRS-TW2ED750JY VRS-TW2ED750JY VRS-TW2ED750JY VRS-TW2ED750JY VRS-TW2ED750JY VRS-CY1JF103JY VRS-CY1JF103JY VRS-CY1JF103JY VRS-CY1JF103JY VRS-CY1JF103JY VRS-CY1JF103JY VRS-CY1JF102JY VRS-CY1JF102JY VRS-CY1JF102JY VRS-CY1JF102JY VRS-CY1JF332JY VRS-CY1JF000JY VRS-CY1JF000JY VRS-CY1JF000JY VRS-CY1JF000JY VRS-CY1JF000JY VRS-CY1JF000JY VRS-CY1JF000JY Description 0.1 10 10 0.1 0.1 0.1 2.2 2.2 2.2 2.2 2.2 0.1 10 0.1 25V 16V 16V 25V 25V 25V 50V 50V 50V 50V 50V 25V 16V 25V Code Ceramic Electrolytic Electrolytic Ceramic Ceramic Ceramic Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Ceramic Electrolytic Ceramic AA Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA RESISTORS CAPACITORS 100p 100p 100p 100p 100p 100p 47 0.01 33p 33p 0.1 18p 18p 18p 0.01 33p 33p 0.1 18p 18p 18p 0.1 10 10 10 10 22 22 0.1 0.1 47 0.01 0.01 47 0.01 47 0.01 47 0.01 47 0.01 47 1000p 1000p ★ Part No. AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AE AE AE AA AA AD AA AA AD AA AD AA AD AA AD AA AD AB AB 149 J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 0 0 0 0 0 75 75 0 75 0 0 75 75 75 47k 10k 100 100 100 100 1k 270 270 75 75 75 47k 10k 100 100 100 100 1k 270 270 75 75 75 75 75 75 10k 10k 10k 10k 10k 10k 1k 1k 1k 1k 3.3k 0 0 0 0 0 0 0 1/10W 1/10W 1/10W 1/10W 1/10W 1/8W 1/8W 1/10W 1/8W 1/10W 1/10W 1/4W 1/4W 1/4W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/4W 1/4W 1/4W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W XG-C50X Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description DUNTKB170DE01 DUNTKB171FE01 INPUT UNIT(Continued) OUTPUT UNIT R3165 R3614 R3615 R3616 R3617 R3701 R3702 R3705 R3706 R3714 R3715 R3716 R3717 R3718 R3719 R3720 R5501 R5502 VRS-CY1JF000JY VRS-CY1JF101JY VRS-CY1JF101JY VRS-CY1JF332JY VRS-CY1JF332JY VRS-TV1JD000JY VRS-CY1JF224JY VRS-CY1JF752FY VRS-CY1JF154JY VRS-CY1JF000JY VRS-CY1JF103JY VRS-CY1JF000JY VRS-CY1JF103JY VRS-CY1JF104JY VRS-CY1JF103JY VRS-CY1JF103JY VRS-CY1JF472JY VRS-CY1JF823JY FB422 FB423 FB431 FB433 FB434 FB442 FB443 FB3002 FB3003 FB3004 FB3005 FB3052 FB3053 FB3054 FB3055 FB3101 FB3102 FB3602 FB3603 FB3609 FB3701 FB3702 FB3703 FB3705 FB5501 J402 J421 J431 J441 J3701 J5501 RBLN-0062CEZZY RBLN-0062CEZZY RBLN-0059CEZZY RBLN-0062CEZZY RBLN-0062CEZZY RBLN-0062CEZZY RBLN-0062CEZZY RBLN-0060TAZZY RBLN-0060TAZZY RBLN-0060TAZZY RBLN-0060TAZZY RBLN-0060TAZZY RBLN-0060TAZZY RBLN-0060TAZZY RBLN-0060TAZZY RBLN-0060TAZZY RBLN-0060TAZZY RBLN-0058CEZZY RBLN-0058CEZZY RBLN-0059CEZZY RBLN-0060TAZZY RBLN-0060TAZZY RBLN-0060TAZZY RBLN-0059CEZZY RBLN-0058CEZZY QSOCD0403GEZZ QJAKJ0008GEZZ QJAKG0064CEZZ QJAKJ0008GEZZ QPLGJ0403CEZZ QJAKJ0007TAZZ J J J J J J J J J J J J J J J J J J 0 100 100 3.3k 3.3k 0 220k 7.5k 150k 0 10k 0 10k 100k 10k 10k 4.7k 82k 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide INTEGRATED CIRCUITS AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA MISCELLANEOUS PARTS J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J SC3001 QSOCN0448FJZZ SC3051 QSOCN0448FJZZ SC3101 QSOCN0344FJZZ J J J SC3102 QCNCW3026TAZZ SC3601 QSOCD0901CEZZ SC3602 QCNCW2026TAZZ PSLDMA009WJFW NSFTZ0134CEFW J J J J J Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead S-Video(INPUT3,4) AUDIO INPUT1,2 Terminal AV Input AUDIO OUTPUT Terminal USB Port Wired Remote Control Input Terminal INPUT1 Terminal INPUT2 terminal OUTPUT(INPUT1,2) Terminal Socket, 30-pin RS-232C Terminal Socket, 20-pin Shield Shaft Code AC AC AB AC AC AC AC AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AE AD AG AD AF AC IC302 IC303 IC1101 IC1102 IC1103 IC1104 IC1105 IC1201 IC1202 IC1301 IC1302 IC2401 IC2402 IC2403 IC2404 IC2601 IC2602 IC2603 IC2604 IC2605 IC2606 IC2701 IC2702 IC2703 IC2751 IC2752 IC4502 IC4505 IC4506 IC4507 IC4508 IC4510 IC4511 IC7001 IC7002 IC7003 IC7004 IC7005 IC7006 IC7007 IC7008 IC7010 VHiLV4053AT-1Y VHiBA3530FS-1Y VHiCXA7000R-1Q VHiCXA7000R-1Q VHiNJM2902V-1Y VHiM62392FP-1Y VHiNJM2904V-1Y VHiCXA7000R-1Q VHiCXA7000R-1Q VHiCXA7000R-1Q VHiCXA7000R-1Q VHiSM5300CS-1Y VHiLMV7239+-1Y VHiLMV7239+-1Y VHiLV125AT+-1Y VHiSNAT541P-1Y RH-iXA176WJZZQ VHiBD4729G+-1Y VHiSN2G32CT-1Y VHiHN24256T-1Y VHiSN2G53CT-1Y VHiM62320FP-1Y VHiM62320FP-1Y VHiSNT1G08C-1Y VHiM62392FP-1Y VHiPQ20WZ11-1Y VHiNJM2244M-1Y VHiBA7655AF-1Y VHiNJM2060V-1Y VHiTHC4538T-1Y VHiSNT1G08C-1Y VHiSNT1G08C-1Y VHiNJM2244M-1Y VHiPQ1R33//-1Y VHiPQ05DZ1U-1Y VHiPQ05DZ1U-1Y VHiPQ05DZ1U-1Y VHiPQ20WZ11-1Y VHiPQ20WZ11-1Y VHiHCT541AF-1Y VHiHCT541AF-1Y VHi74F86NSR-1Y Q301 Q302 Q303 Q304 Q305 Q306 Q307 Q308 Q1101 Q1102 Q1103 Q1104 Q1105 Q1106 Q1107 Q1108 Q1109 Q1201 Q1202 Q1203 Q1204 Q1205 Q1206 Q1207 Q1208 Q1301 VS2SA1530AR-1Y VS2SD1760QA-1Y VS2SD1760QA-1Y VSHN2C01FU/-1Y VSHN2C01FU/-1Y VS2SC3928AR-1Y VSDTC144EUA-1Y VSDTC144EUA-1Y VS2SA1530AR-1Y VS2SC3928AR-1Y VS2SC3928AR-1Y VS2SA1530AR-1Y VS2SA1530AR-1Y VS2SC3928AR-1Y VS2SA1530AR-1Y VS2SC3928AR-1Y VS2SA1530AR-1Y VS2SC3928AR-1Y VS2SA1530AR-1Y VS2SC3928AR-1Y VS2SA1530AR-1Y VS2SC3928AR-1Y VS2SA1530AR-1Y VS2SC3928AR-1Y VS2SA1530AR-1Y VS2SC3928AR-1Y J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J SN74LV4053APWR BA3530FS-E1 CXA7000R CXA7000R NJM2902V M62392FP NJM2904V CXA7000R CXA7000R CXA7000R CXA7000R SM5300CS LMV7239M5X LMV7239M5X SN74LV125APWR SN74AHCt541PWR A176WJ BD4729G-TR SN74AHC2G32HDC HN58X24256TI SN74AHC2G53HDC M62320FP M62320FP SN74AHCT1G08DC M62392FP PQ20WZ1U NJM2244M BA7655AF NJM2060V TC74HC4538AFT SN74AHCT1G08DC SN74AHCT1G08DC NJM2244M PQ1R33 PQ05DZ1U PQ05DZ1U PQ05DZ1U PQ20WZ1U PQ20WZ1U TC74HCT541AF TC74HCT541AF SN74F86NSR AE AM AZ AZ AD AM AF AZ AZ AZ AZ AP AG AG AE AF AQ AD AE AT AE AH AH AD AM AF AG AG AF AL AD AD AG AE AG AG AG AF AF AF AF AD TRANSISTORS AM AM AM AF AH AE AH AD 150 J J J J J J J J J J J J J J J J J J J J J J J J J J 2SA1530AR 2SD1760QA 2SD1760QA HN2C01FU HN2C01FU 2SC3928AR DTC144EUA DTC144EUA 2SA1530AR 2SC3928AR 2SC3928AR 2SA1530AR 2SA1530AR 2SC3928AR 2SA1530AR 2SC3928AR 2SA1530AR 2SC3928AR 2SA1530AR 2SC3928AR 2SA1530AR 2SC3928AR 2SA1530AR 2SC3928AR 2SA1530AR 2SC3928AR AB AC AC AC AC AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB XG-C50X Ref. No. ★ Part No. Description Code Ref. No. DUNTKB171FE01 C310 C311 C312 C313 C314 C315 C316 C317 C318 C319 C320 C321 C322 C323 C324 C1101 C1102 C1103 C1104 C1105 C1106 C1107 C1108 C1109 C1110 C1112 C1113 C1114 C1115 C1116 C1117 C1118 C1119 C1120 C1121 C1122 C1123 C1124 C1125 C1126 C1127 C1128 C1130 C1131 C1140 C1141 C1142 C1143 C1144 C1145 C1146 C1147 C1201 C1202 C1203 C1204 C1205 C1206 C1207 C1208 C1209 C1210 C1211 C1212 C1213 C1214 C1215 C1216 C1217 C1219 C1220 C1222 C1223 C1224 C1225 OUTPUT UNIT(Continued) Q1302 Q1303 Q1304 Q1305 Q1306 Q1307 Q1308 Q2401 Q2402 Q2403 Q2415 Q2416 Q2417 Q2418 Q2419 Q2420 Q2701 Q2702 Q2751 Q2752 Q2753 Q2754 Q2755 Q2756 Q4501 Q4502 Q4504 Q4505 Q4506 Q4511 Q4512 Q4513 Q4514 Q4515 Q7001 Q7002 Q7003 Q7004 Q7005 VS2SA1530AR-1Y VS2SC3928AR-1Y VS2SA1530AR-1Y VS2SC3928AR-1Y VS2SA1530AR-1Y VS2SC3928AR-1Y VS2SA1530AR-1Y VS2SC2735//-1Y VS2SC2735//-1Y VS2SC2735//-1Y VSHN1B04FU/-1Y VS2SC3928AR-1Y VS2SC3928AR-1Y VSDTC114EUA-1Y VSHN1C01FU/-1Y VSHN1C01FU/-1Y VSBSN20////-1Y VSHN1K03FU+-1Y VS2SC3928AR-1Y VSHN2C01FU/-1Y VSDTA114EUA-1Y VS2SC3928AR-1Y VSDTC144EUA-1Y VS2SA1530AR-1Y VS2SC3928AR-1Y VS2SC3928AR-1Y VS2SC3928AR-1Y VS2SA1530AR-1Y VS2SC3928AR-1Y VS2SA1530AR-1Y VS2SA1530AR-1Y VS2SA1530AR-1Y VS2SC3928AR-1Y VS2SC3928AR-1Y VS2SC2412K/-1Y VSHN2C01FU/-1Y VSDTC114EUA-1Y VSDTC114EUA-1Y VSDTC114EUA-1Y J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 2SA1530AR 2SC3928AR 2SA1530AR 2SC3928AR 2SA1530AR 2SC3928AR 2SA1530AR 2SC2735 2SC2735 2SC2735 HN1B04FU 2SC3928AR 2SC3928AR DTC114EUA HN1C01FU HN1C01FU BSN20 HN1K03FU 2SC3928AR HN2C01FU DTA114EUA 2SC3928AR DTC144EUA 2SA1530AR 2SC3928AR 2SC3928AR 2SC3928AR 2SA1530AR 2SC3928AR 2SA1530AR 2SA1530AR 2SA1530AR 2SC3928AR 2SC3928AR 2SC2412K HN2C01FU DTC114EUA DTC114EUA DTC114EUA D2751 D2752 D4501 D4502 D4503 D4504 D7001 D7002 D7003 D7004 D7005 VHDDAN202K/-1Y VHDDAN202K/-1Y RH-EX0519CEZZY RH-EX0519CEZZY VHDMA152WA/-1Y VHDMA152WA/-1Y VHDDAN202K/-1Y VHDDAN202K/-1Y VHDDAN202K/-1Y VHDDAN202K/-1Y VHDDAN202K/-1Y X2601 RCRSB0286CEZZY J Crystal L1101 L1102 L1201 L1202 L1301 L1302 L4501 L4504 VP-1M100J1R6NY VP-1M100J1R6NY VP-1M100J1R6NY VP-1M100J1R6NY VP-1M100J1R6NY VP-1M100J1R6NY VP-1M220J2R9NY VP-1M220J2R9NY C301 C302 C303 C309 VCEAPF1CW106MY J VCEAPF1CW106MY J VCEAPF1CW106MY J VCKYCY1EF104ZY J AB AB AB AB AB AB AB AB AB AB AC AB AB AB AC AC AD AD AB AC AA AB AB AB AB AB AB AB AB AB AB AB AB AB AA AC AB AB AB DIODES J J J J J J J J J J J Diode Diode Zener Diode Zener Diode Diode Diode Diode Diode Diode Diode Diode AB AB AB AB AB AB AB AB AB AB AB PACKAGED CIRCUIT AH COILS AND FILTERS J J J J J J J J Peaking 10µH Peaking 10µH Peaking 10µH Peaking 10µH Peaking 10µH Peaking 10µH Peaking 22µH Peaking 22µH AB AB AB AB AB AB AB AB CAPACITORS 10 10 10 0.1 16V 16V 16V 25V Electrolytic Electrolytic Electrolytic Ceramic AB AB AB AA 151 Part No. ★ VCEAPF1CW106MY J VCEAPF1CW106MY J VCEAPF1CW106MY J VCEAPF1CW106MY J VCEAPF1CW106MY J VCE9PF1HW105MY J VCEAPF0JW107MY J VCE9PF1HW105MY J VCKYCY1AF105ZY J VCKYCY1AF105ZY J VCKYCY1AF105ZY J VCEAPF0JW107MY J VCEAPF1CW106MY J VCEAPF1CW106MY J VCCCCY1HH102JY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J RC-KZ0416CEZZY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J RC-KZ0416CEZZY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCKYCY1AF105ZY J RC-KZ0416CEZZY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J RC-KZ0416CEZZY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J RC-KZ0416CEZZY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCKYCY1AF105ZY J VCKYCY1EF104ZY J RC-KZ0416CEZZY J RC-KZ0416CEZZY J VCKYCY1EF104ZY J RC-KZ0416CEZZY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCKYCY1AF105ZY J VCKYCY1AF105ZY J VCKYCY1AF105ZY J VCKYCY1AF105ZY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J RC-KZ0416CEZZY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J RC-KZ0416CEZZY J VCKYCY1EF104ZY J RC-KZ0416CEZZY J VCKYCY1EF104ZY J VCKYCY1AF105ZY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J RC-KZ0416CEZZY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J RC-KZ0416CEZZY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCKYCY1AF105ZY J RC-KZ0416CEZZY J VCKYCY1EF104ZY J RC-KZ0416CEZZY J VCKYCY1EF104ZY J Description 10 10 10 10 10 1 100 1 1 1 1 100 10 10 1000p 0.1 0.1 10 0.1 0.1 10 0.1 0.1 1 10 0.1 0.1 10 0.1 0.1 10 0.1 0.1 0.1 1 0.1 10 10 0.1 10 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 1 1 1 1 0.1 0.1 10 0.1 0.1 10 0.1 10 0.1 1 0.1 0.1 10 0.1 0.1 10 0.1 0.1 1 10 0.1 10 0.1 16V 16V 16V 16V 16V 50V 6.3V 50V 10V 10V 10V 6.3V 16V 16V 50V 25V 25V 25V 25V 25V 25V 25V 25V 10V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 10V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 10V 10V 10V 10V 25V 25V 25V 25V 25V 25V 25V 25V 25V 10V 25V 25V 25V 25V 25V 25V 25V 25V 10V 25V 25V 25V 25V Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Elect.(N.P) Electrolytic Elect.(N.P) Ceramic Ceramic Ceramic Electrolytic Electrolytic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Code AB AB AB AB AB AC AC AC AC AC AC AC AB AB AB AA AA AE AA AA AE AA AA AC AE AA AA AE AA AA AE AA AA AA AC AA AE AE AA AE AA AA AA AA AA AA AA AA AC AC AC AC AA AA AE AA AA AE AA AE AA AC AA AA AE AA AA AE AA AA AC AE AA AE AA XG-C50X Ref. No. Part No. ★ Description Code Ref. No. AE AA AA AA AA AA AA AA AA AE AA AA AE AA AE AC AA AA AE AA AA AE AA AC AE AA AE AA AE AA AA AA AA AA AA AA AA AA AC AC AC AA AA AB AA AA AB AD AA AA AA AB AA AA AB AA AA AB AB AB AA AA AA AA AA AA AA AA AB AA AA C2613 C2614 C2615 C2616 C2617 C2618 C2701 C2702 C2703 C2751 C2752 C2757 C2759 C2760 C4501 C4502 C4503 C4504 C4505 C4506 C4523 C4524 C4525 C4546 C4547 C4548 C4549 C4551 C4552 C4554 C4555 C4556 C4557 C4558 C4559 C4560 C4561 C4562 C4563 C4564 C4565 C4566 C4567 C4568 C4569 C4570 C4571 C4572 C4573 C4574 C4575 C4576 C7001 C7002 C7003 C7004 C7005 C7006 C7007 C7008 C7009 C7011 C7012 C7013 C7014 C7015 C7016 C7017 C7018 C7019 C7020 C7025 C7036 C7037 C7038 DUNTKB171FE01 OUTPUT UNIT(Continued) C1226 C1227 C1228 C1240 C1241 C1242 C1243 C1301 C1302 C1303 C1304 C1305 C1306 C1307 C1308 C1309 C1310 C1311 C1312 C1313 C1314 C1315 C1316 C1317 C1318 C1319 C1320 C1321 C1322 C1323 C1325 C1326 C1327 C1340 C1341 C1342 C1343 C2401 C2402 C2403 C2404 C2407 C2408 C2409 C2410 C2420 C2421 C2422 C2423 C2424 C2425 C2426 C2427 C2428 C2441 C2442 C2443 C2445 C2446 C2447 C2448 C2601 C2604 C2605 C2606 C2607 C2608 C2609 C2610 C2611 C2612 RC-KZ0416CEZZY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J RC-KZ0416CEZZY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J RC-KZ0416CEZZY J VCKYCY1EF104ZY J RC-KZ0416CEZZY J VCKYCY1AF105ZY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J RC-KZ0416CEZZY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J RC-KZ0416CEZZY J VCKYCY1EF104ZY J VCKYCY1AF105ZY J RC-KZ0416CEZZY J VCKYCY1EF104ZY J RC-KZ0416CEZZY J VCKYCY1EF104ZY J RC-KZ0416CEZZY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCE9PF1HW105MY J VCE9PF1HW105MY J VCE9PF1HW105MY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCEAPF1CW106MY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCEAPF1CW106MY J VCE9PF1HW474MY J VCCCCY1HH5R0CY J VCKYCY1HB222KY J VCKYCY1EF104ZY J VCEAPF1CW106MY J VCKYCY1EF104ZY J VCCCCY1HH101JY J VCEAPF1CW106MY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCEAPF1CW106MY J VCEAPF1CW106MY J VCEAPF1CW106MY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCEAPF0JW476MY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J 10 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 10 0.1 0.1 10 0.1 10 1 0.1 0.1 10 0.1 0.1 10 0.1 1 10 0.1 10 0.1 10 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 1 1 1 0.1 0.1 10 0.1 0.1 10 0.47 5p 2200p 0.1 10 0.1 100p 10 0.1 0.1 10 10 10 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 47 0.1 0.1 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 10V 25V 25V 25V 25V 25V 25V 25V 10V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 50V 50V 50V 25V 25V 16V 25V 25V 16V 50V 50V 50V 25V 16V 25V 50V 16V 25V 25V 16V 16V 16V 25V 25V 25V 25V 25V 25V 25V 25V 6.3V 25V 25V Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Elect.(N.P) Elect.(N.P) Elect.(N.P) Ceramic Ceramic Electrolytic Ceramic Ceramic Electrolytic Elect.(N.P) Ceramic Ceramic Ceramic Electrolytic Ceramic Ceramic Electrolytic Ceramic Ceramic Electrolytic Electrolytic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Ceramic Ceramic 152 Part No. ★ VCKYCY1EF104ZY J VCCCCY1HH220JY J VCCCCY1HH220JY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCEAPF1CW106MY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCEAPF1CW226MY J VCEAPF1CW476MY J VCEAPF1CW476MY J VCEAPF1HW225MY J VCEAPF1CW106MY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCEAPF1CW106MY J VCEAPF1CW106MY J VCKYCY1EF104ZY J VCCCCY1HH471JY J VCKYCY1EF104ZY J VCKYTV1CB334KY J VCKYCY1EF104ZY J VCCCCY1HH270JY J VCCCCY1HH120JY J VCCCCY1HH100DY J VCKYCY1EF104ZY J VCEAPF0JW476MY J VCE9PF1CW106MY J VCKYCY1EF104ZY J VCEAPF1CW106MY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCEAPF1HW225MY J VCKYCY1HB103KY J VCCCCY1HH101JY J VCKYCY1HB103KY J VCE9PF1HW105MY J VCCCCY1HH101JY J VCKYCY1EF104ZY J VCCCCY1HH471JY J VCEAPF1CW106MY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCEAPF1CW106MY J VCCCCY1HH102JY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCE9PF1CW106MY J VCE9PF1CW106MY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCEAPF1CW476MY J VCEAPF0JW107MY J VCEAPF0JW107MY J VCKYCY1EF104ZY J VCEAPF1CW106MY J VCEAPF1CW106MY J VCEAPF0JW107MY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCEAPF1EW226MY J VCEAPF1EW226MY J VCEAPF1EW226MY J VCKYCY1EF104ZY J VCEAPF1EW226MY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J Description 0.1 22p 22p 0.1 0.1 0.1 10 0.1 0.1 0.1 22 47 47 2.2 10 0.1 0.1 10 10 0.1 470p 0.1 0.33 0.1 27p 12p 10p 0.1 47 10 0.1 10 0.1 0.1 2.2 0.01 100p 0.01 1 100p 0.1 470p 10 0.1 0.1 10 1000p 0.1 0.1 10 10 0.1 0.1 0.1 0.1 0.1 47 100 100 0.1 10 10 100 0.1 0.1 22 22 22 0.1 22 0.1 0.1 0.1 0.1 0.1 25V 50V 50V 25V 25V 25V 16V 25V 25V 25V 16V 16V 16V 50V 16V 25V 25V 16V 16V 25V 50V 25V 16V 25V 50V 50V 50V 25V 6.3V 16V 25V 16V 25V 25V 50V 50V 50V 50V 50V 50V 25V 50V 16V 25V 25V 16V 50V 25V 25V 16V 16V 25V 25V 25V 25V 25V 16V 6.3V 6.3V 25V 16V 16V 6.3V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Ceramic Ceramic Ceramic Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Ceramic Ceramic Electrolytic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Elect.(N.P) Ceramic Electrolytic Ceramic Ceramic Electrolytic Ceramic Ceramic Ceramic Elect.(N.P) Ceramic Ceramic Ceramic Electrolytic Ceramic Ceramic Electrolytic Ceramic Ceramic Ceramic Elect.(N.P) Elect.(N.P) Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Electrolytic Electrolytic Ceramic Electrolytic Electrolytic Electrolytic Ceramic Ceramic Electrolytic Electrolytic Electrolytic Ceramic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Code AA AA AA AA AA AA AB AA AA AA AB AC AC AB AB AA AA AB AB AA AA AA AC AA AA AA AA AA AB AC AA AB AA AA AB AA AA AA AC AA AA AA AB AA AA AB AB AA AA AC AC AA AA AA AA AA AC AC AC AA AB AB AC AA AA AD AD AD AA AD AA AA AA AA AA XG-C50X Ref. No. ★ Part No. Description Code DUNTKB171FE01 OUTPUT UNIT(Continued) C7039 C7041 C7042 C7043 C7044 C7045 C7046 C7047 C7048 C7049 C7050 C7051 C7052 C7053 C7054 C7055 C7056 C7057 C7058 C7059 C7060 C7061 C7062 C7063 C7064 C7065 C7066 C7067 C7068 C7069 C7070 VCKYCY1EF104ZY VCCCCY1HH120JY VCCCCY1HH120JY VCCCCY1HH120JY VCCCCY1HH120JY VCCCCY1HH120JY VCCCCY1HH120JY VCCCCY1HH120JY VCCCCY1HH120JY VCCCCY1HH120JY VCCCCY1HH120JY VCCCCY1HH120JY VCCCCY1HH120JY VCCCCY1HH120JY VCCCCY1HH120JY VCCCCY1HH120JY VCCCCY1HH120JY VCCCCY1HH120JY VCCCCY1HH120JY VCCCCY1HH120JY VCCCCY1HH120JY VCCCCY1HH120JY VCCCCY1HH120JY VCCCCY1HH120JY VCCCCY1HH120JY VCCCCY1HH120JY VCCCCY1HH120JY VCCCCY1HH120JY VCCCCY1HH120JY VCCCCY1HH120JY VCCCCY1HH120JY R301 R302 R303 R304 R305 R306 R307 R308 R310 R311 R313 R314 R315 R316 R317 R318 R319 R320 R321 R322 R323 R324 R325 R326 R327 R328 R329 R330 R331 R332 R335 R336 R337 R338 R339 R340 R342 R343 VRS-CY1JF682JY VRS-CY1JF103JY VRS-CY1JF471JY VRS-CE3AF1R0JY VRS-TX2HF2R2JY VRS-TX2HF2R2JY VRS-CY1JF223JY VRS-CY1JF152JY VRS-CY1JF682JY VRS-CY1JF432JY VRS-CY1JF102JY VRS-CY1JF102JY VRS-CY1JF101JY VRS-CY1JF101JY VRS-CY1JF102JY VRS-CY1JF101JY VRS-CY1JF101JY VRS-CY1JF103JY VRS-CY1JF103JY VRS-CY1JF104JY VRS-CY1JF562JY VRS-CY1JF562JY VRS-CY1JF103JY VRS-CY1JF104JY VRS-CY1JF104JY VRS-CY1JF104JY VRS-CY1JF104JY VRS-CY1JF103JY VRS-CY1JF224JY VRS-CY1JF224JY VRS-CY1JF562JY VRS-CY1JF562JY VRS-CY1JF103JY VRS-CY1JF104JY VRS-CY1JF104JY VRS-CY1JF224JY VRS-CY1JF103JY VRS-CY1JF104JY J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 0.1 12p 12p 12p 12p 12p 12p 12p 12p 12p 12p 12p 12p 12p 12p 12p 12p 12p 12p 12p 12p 12p 12p 12p 12p 12p 12p 12p 12p 12p 12p 25V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide AA AA AA AC AB AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA RESISTORS J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 6.8k 10k 470 1 2.2 2.2 22k 1.5k 6.8k 4.3k 1k 1k 100 100 1k 100 100 10k 10k 100k 5.6k 5.6k 10k 100k 100k 100k 100k 10k 220k 220k 5.6k 5.6k 10k 100k 100k 220k 10k 100k 1/16W 1/16W 1/16W 1W 1/2W 1/2W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 153 Ref. No. Part No. ★ R344 R345 R347 R348 R349 R350 R351 R352 R353 R354 R355 R356 R357 R358 R1101 R1102 R1103 R1104 R1105 R1107 R1108 R1109 R1110 R1111 R1112 R1113 R1114 R1115 R1116 R1117 R1119 R1120 R1121 R1122 R1123 R1124 R1125 R1126 R1127 R1128 R1129 R1130 R1131 R1132 R1133 R1134 R1135 R1136 R1137 R1138 R1139 R1140 R1141 R1142 R1144 R1145 R1146 R1147 R1148 R1149 R1150 R1151 R1152 R1153 R1154 R1155 R1156 R1157 R1158 R1159 R1160 R1161 R1162 R1164 R1165 VRS-CY1JF104JY VRS-CY1JF224JY VRS-CY1JF154JY VRS-CY1JF154JY VRS-CY1JF104JY VRS-CY1JF104JY VRS-CY1JF103JY VRS-CY1JF473JY VRS-CY1JF473JY VRS-CY1JF562JY VRS-CY1JF681JY VRS-CY1JF681JY VRS-CY1JF105JY VRS-CY1JF105JY VRS-CY1JF102JY VRS-CY1JF102JY VRS-CY1JF332JY VRS-CY1JF332JY VRS-CY1JF102JY VRS-CY1JF680JY VRS-CY1JF102JY VRS-CY1JF102JY VRS-CY1JF332JY VRS-CY1JF332JY VRS-CY1JF102JY VRS-CY1JF680JY VRS-CY1JF270JY VRS-CY1JF272JY VRS-CY1JF222JY VRS-CY1JF103FY VRS-CY1JF100JY VRS-CY1JF100JY VRS-CY1JF100JY VRS-CY1JF100JY VRS-CY1JF203FY VRS-CY1JF100JY VRS-CY1JF100JY VRS-CY1JF100JY VRS-CY1JF100JY VRS-CY1JF103FY VRS-CY1JF100JY VRS-CY1JF100JY VRS-CY1JF101JY VRS-CY1JF222JY VRS-CY1JF3R3JY VRS-CY1JF222JY VRS-CY1JF3R3JY VRS-CY1JF3R3JY VRS-CY1JF101JY VRS-CY1JF222JY VRS-CY1JF3R3JY VRS-CY1JF222JY VRS-CY1JF3R3JY VRS-CY1JF3R3JY VRS-CY1JF000JY VRS-CY1JF332JY VRS-CA1JF332JY VRS-CY1JF203FY VRS-CY1JF103FY VRS-CY1JF103FY VRS-CY1JF203FY VRS-CY1JF203FY VRS-CY1JF153FY VRS-CY1JF153FY VRS-CY1JF153FY VRS-CY1JF682FY VRS-CY1JF682FY VRS-CY1JF682FY VRS-CY1JF562FY VRS-CY1JF562FY VRS-CY1JF562FY VRS-CY1JF103FY VRS-CY1JF682FY VRS-CY1JF000JY VRS-CY1JF000JY J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J Description 100k 220k 150k 150k 100k 100k 10k 47k 47k 5.6k 680 680 1M 1M 1k 1k 3.3k 3.3k 1k 68 1k 1k 3.3k 3.3k 1k 68 27 2.7k 2.2k 10k 10 10 10 10 20k 10 10 10 10 10k 10 10 100 2.2k 3.3 2.2k 3.3 3.3 100 2.2k 3.3 2.2k 3.3 3.3 0 3.3k 3.3k 20k 10k 10k 20k 20k 15k 15k 15k 6.8k 6.8k 6.8k 5.6k 5.6k 5.6k 10k 6.8k 0 0 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Code AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA XG-C50X Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA R1324 R1325 R1326 R1327 R1328 R1329 R1330 R1332 R1333 R1334 R1335 R1336 R1337 R1401 R1402 R1403 R1404 R1405 R1406 R1407 R2410 R2411 R2412 R2413 R2415 R2416 R2418 R2440 R2441 R2442 R2443 R2444 R2445 R2446 R2447 R2448 R2449 R2450 R2451 R2452 R2456 R2457 R2458 R2459 R2460 R2461 R2462 R2463 R2464 R2465 R2466 R2467 R2602 R2603 R2604 R2605 R2609 R2611 R2612 R2614 R2615 R2616 R2618 R2620 R2621 R2622 R2623 R2626 R2635 R2636 R2637 R2638 R2639 R2640 R2641 VRS-CY1JF100JY VRS-CY1JF101JY VRS-CY1JF222JY VRS-CY1JF222JY VRS-CY1JF3R3JY VRS-CY1JF3R3JY VRS-CY1JF3R3JY VRS-CY1JF101JY VRS-CY1JF222JY VRS-CY1JF222JY VRS-CY1JF3R3JY VRS-CY1JF3R3JY VRS-CY1JF3R3JY VRS-CY1JF101JY VRS-CY1JF393FY VRS-CY1JF682FY VRS-CY1JF101JY VRS-CY1JF103FY VRS-CY1JF203FY VRS-CY1JF393FY VRS-CY1JF103JY VRS-TV1JD680JY VRS-CY1JF103JY VRS-TV1JD680JY VRS-CY1JF103JY VRS-TV1JD680JY VRS-CY1JF821JY VRS-CY1JF102JY VRS-CY1JF102JY VRS-CY1JF123JY VRS-CY1JF471JY VRS-CY1JF470JY VRS-CY1JF333JY VRS-CY1JF821JY VRS-CY1JF472JY VRS-CY1JF392FY VRS-CY1JF151FY VRS-CY1JF112FY VRS-CY1JF100JY VRS-CY1JF183JY VRS-CY1JF183JY VRS-CY1JF183JY VRS-CY1JF103JY VRS-CY1JF103JY VRS-CY1JF103JY VRS-CY1JF101JY VRS-CY1JF101JY VRS-CY1JF101JY VRS-CY1JF102JY VRS-CY1JF102JY VRS-CY1JF102JY VRS-CY1JF102JY VRS-CY1JF100JY VRS-CY1JF103JY VRS-CY1JF103JY VRS-CY1JF100JY VRS-CY1JF104JY VRS-CY1JF000JY VRS-CY1JF000JY VRS-CY1JF104JY VRS-CY1JF101JY VRS-CY1JF222JY VRS-CY1JF104JY VRS-CY1JF101JY VRS-CY1JF104JY VRS-CY1JF332JY VRS-CY1JF182JY VRS-CY1JF000JY VRS-CY1JF103FY VRS-CY1JF103FY VRS-CY1JF103FY VRS-CY1JF103FY VRS-CY1JF103FY VRS-CY1JF682JY VRS-CY1JF682JY J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J DUNTKB171FE01 OUTPUT UNIT(Continued) R1166 R1167 R1168 R1169 R1170 R1171 R1172 R1173 R1174 R1189 R1190 R1191 R1192 R1193 R1194 R1195 R1196 R1197 R1198 R1199 R1201 R1202 R1203 R1204 R1205 R1207 R1208 R1209 R1210 R1211 R1212 R1213 R1214 R1215 R1217 R1218 R1219 R1220 R1222 R1223 R1225 R1226 R1227 R1228 R1229 R1230 R1232 R1233 R1234 R1235 R1236 R1237 R1301 R1302 R1303 R1304 R1305 R1307 R1308 R1309 R1310 R1311 R1313 R1314 R1315 R1316 R1318 R1319 R1320 R1321 R1323 VRS-CY1JF132FY VRS-CY1JF152FY VRS-CY1JF132FY VRS-CY1JF132FY VRS-CY1JF152FY VRS-CY1JF152FY VRS-CY1JF102FY VRS-CY1JF102FY VRS-CY1JF102FY VRS-CY1JF101JY VRS-CY1JF222FY VRS-CY1JF332FY VRS-CY1JF222FY VRS-CY1JF332FY VRS-CY1JF222FY VRS-CY1JF332FY VRS-CY1JF203FY VRS-CY1JF101JY VRS-CY1JF682FY VRS-CY1JF393FY VRS-CY1JF102JY VRS-CY1JF102JY VRS-CY1JF102JY VRS-CY1JF332JY VRS-CY1JF332JY VRS-CY1JF102JY VRS-CY1JF102JY VRS-CY1JF332JY VRS-CY1JF332JY VRS-CY1JF102JY VRS-CY1JF100JY VRS-CY1JF100JY VRS-CY1JF100JY VRS-CY1JF100JY VRS-CY1JF100JY VRS-CY1JF100JY VRS-CY1JF100JY VRS-CY1JF100JY VRS-CY1JF100JY VRS-CY1JF100JY VRS-CY1JF101JY VRS-CY1JF222JY VRS-CY1JF222JY VRS-CY1JF3R3JY VRS-CY1JF3R3JY VRS-CY1JF3R3JY VRS-CY1JF3R3JY VRS-CY1JF3R3JY VRS-CY1JF3R3JY VRS-CY1JF222JY VRS-CY1JF222JY VRS-CY1JF101JY VRS-CY1JF102JY VRS-CY1JF102JY VRS-CY1JF102JY VRS-CY1JF332JY VRS-CY1JF332JY VRS-CY1JF102JY VRS-CY1JF102JY VRS-CY1JF332JY VRS-CY1JF332JY VRS-CY1JF102JY VRS-CY1JF100JY VRS-CY1JF100JY VRS-CY1JF100JY VRS-CY1JF100JY VRS-CY1JF100JY VRS-CY1JF100JY VRS-CY1JF100JY VRS-CY1JF100JY VRS-CY1JF100JY J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 1.3k 1.5k 1.3k 1.3k 1.5k 1.5k 1k 1k 1k 100 2.2k 3.3k 2.2k 3.3k 2.2k 3.3k 20k 100 6.8k 39k 1k 1k 1k 3.3k 3.3k 1k 1k 3.3k 3.3k 1k 10 10 10 10 10 10 10 10 10 10 100 2.2k 2.2k 3.3 3.3 3.3 3.3 3.3 3.3 2.2k 2.2k 100 1k 1k 1k 3.3k 3.3k 1k 1k 3.3k 3.3k 1k 10 10 10 10 10 10 10 10 10 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide 154 Description 10 100 2.2k 2.2k 3.3 3.3 3.3 100 2.2k 2.2k 3.3 3.3 3.3 100 39k 6.8k 100 10k 20k 39k 10k 68 10k 68 10k 68 820 1k 1k 12k 470 47 33k 820 4.7k 3.9k 150 1.1k 10 18k 18k 18k 10k 10k 10k 100 100 100 1k 1k 1k 1k 10 10k 10k 10 100k 0 0 100k 100 2.2k 100k 100 100k 3.3k 1.8k 0 10k 10k 10k 10k 10k 6.8k 6.8k 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Code AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA XG-C50X Ref. No. Part No. ★ Description Code Ref. No. AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AC AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA R4561 R4562 R4563 R4564 R4565 R4566 R4567 R4568 R4569 R4570 R4571 R4572 R4574 R4575 R4576 R4577 R4578 R4580 R4581 R4585 R4586 R4587 R4590 R4592 R4593 R4594 R7001 R7002 R7004 R7005 R7009 R7010 R7011 R7012 R7013 R7014 R7015 R7016 R7018 R7019 R7020 R7021 R7022 R7023 R7024 R7026 R7027 R7028 R7029 R7030 R7031 R7032 R7033 R7034 R7035 R7040 R7041 R7042 R7043 R7044 R7045 R7046 R7047 R7048 R7049 R7050 R7054 R7058 R7061 R7062 R7063 R7064 R7065 R7066 R7067 DUNTKB171FE01 OUTPUT UNIT(Continued) R2701 R2703 R2704 R2705 R2706 R2707 R2708 R2711 R2712 R2713 R2714 R2715 R2716 R2718 R2721 R2722 R2723 R2724 R2726 R2727 R2751 R2752 R2753 R2754 R2755 R2756 R2757 R2758 R2759 R2760 R2761 R2762 R2763 R2767 R2770 R2771 R2772 R2773 R2774 R4501 R4502 R4503 R4504 R4505 R4506 R4507 R4518 R4519 R4520 R4521 R4522 R4523 R4524 R4542 R4543 R4544 R4545 R4546 R4547 R4548 R4549 R4550 R4551 R4553 R4554 R4555 R4556 R4557 R4558 R4559 R4560 VRS-CA1JF101JY VRS-CY1JF103JY VRS-CY1JF103JY VRS-CY1JF103JY VRS-CY1JF101JY VRS-CY1JF101JY VRS-CA1JF101JY VRS-CY1JF101JY VRS-CY1JF101JY VRS-CY1JF101JY VRS-CY1JF103JY VRS-CY1JF272JY VRS-CA1JF101JY VRS-CY1JF101JY VRS-CY1JF473FY VRS-CY1JF473FY VRS-CY1JF101JY VRS-CY1JF272JY VRS-CY1JF000JY VRS-CY1JF103JY VRS-CA1JF101JY VRS-CY1JF000JY VRS-CY1JF103JY VRS-CY1JF103FY VRS-CY1JF332FY VRS-CY1JF224FY VRS-CY1JF333FY VRS-CE3AF1R0JY VRS-CY1JF222JY VRS-CY1JF103JY VRS-CY1JF000JY VRS-CY1JF472JY VRS-CY1JF393JY VRS-CY1JF103JY VRS-CY1JF182JY VRS-CY1JF392JY VRS-CY1JF103JY VRS-CY1JF102JY VRS-CY1JF104JY VRS-CY1JF105JY VRS-CY1JF105JY VRS-CY1JF105JY VRS-CY1JF470JY VRS-CY1JF102JY VRS-CY1JF470JY VRS-CY1JF102JY VRS-CY1JF472JY VRS-CY1JF471JY VRS-CY1JF102JY VRS-CY1JF222JY VRS-CY1JF473JY VRS-CY1JF224JY VRS-CY1JF221JY VRS-CY1JF152JY VRS-CY1JF911JY VRS-CY1JF182JY VRS-CY1JF182FY VRS-CY1JF221FY VRS-CY1JF102JY VRS-CY1JF273JY VRS-CY1JF183JY VRS-CY1JF102FY VRS-TV1JD000JY VRS-CY1JF000JY VRS-CY1JF102JY VRS-CY1JF103JY VRS-CY1JF682JY VRS-CY1JF223JY VRS-CY1JF393JY VRS-CY1JF393JY VRS-CY1JF103JY J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 100 10k 10k 10k 100 100 100 100 100 100 10k 2.7k 100 100 47k 47k 100 2.7k 0 10k 100 0 10k 10k 3.3k 220k 33k 1 2.2k 10k 0 4.7k 39k 10k 1.8k 3.9k 10k 1k 100k 1M 1M 1M 47 1k 47 1k 4.7k 470 1k 2.2k 47k 220k 220 1.5k 910 1.8k 1.8k 220 1k 27k 18k 1k 0 0 1k 10k 6.8k 22k 39k 39k 10k 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide 155 Part No. VRS-CY1JF223JY VRS-CY1JF473JY VRS-CY1JF472JY VRS-CY1JF393JY VRS-CY1JF274JY VRS-CY1JF683JY VRS-CY1JF102JY VRS-CY1JF102JY VRS-CY1JF103JY VRS-CY1JF103JY VRS-CY1JF222JY VRS-CY1JF105JY VRS-CY1JF000JY VRS-CY1JF000JY VRS-CY1JF000JY VRS-CY1JF222JY VRS-CY1JF000JY VRS-CY1JF394JY VRS-CY1JF000JY VRS-CY1JF104JY VRS-CY1JF821JY VRS-CY1JF104JY VRS-CY1JF105JY VRS-CY1JF105JY VRS-CY1JF105JY VRS-CY1JF000JY VRS-CY1JF103JY VRS-TX2HF1R0JY VRS-CY1JF471JY VRS-CY1JF471JY VRS-CY1JF101JY VRS-TX2HF1R0JY VRS-CY1JF103JY VRS-TX2HF1R0JY VRS-CY1JF683FY VRS-CY1JF822FY VRS-CY1JF152FY VRS-CY1JF103JY VRS-CY1JF683FY VRS-CY1JF682FY VRS-CY1JF152FY VRS-CY1JF100JY VRS-CY1JF100JY VRS-CY1JF100JY VRS-CY1JF100JY VRS-CY1JF100JY VRS-CY1JF100JY VRS-CY1JF100JY VRS-CY1JF100JY VRS-CY1JF100JY VRS-CY1JF100JY VRS-CY1JF100JY VRS-CY1JF100JY VRS-CY1JF100JY VRS-CY1JF100JY VRS-CY1JF103JY VRS-CY1JF102JY VRS-CY1JF472JY VRS-CY1JF102JY VRS-CY1JF102JY VRS-CY1JF472JY VRS-CY1JF121JY VRS-CY1JF121JY VRS-TV1JD121JY VRS-TV1JD121JY VRN-CY1JF103DY VRN-CY1JF103DY VRS-CY1JF103JY VRS-CB1JF100JY VRS-CY1JF100JY VRS-CA1JF100JY VRS-CB1JF100JY VRS-CB1JF100JY VRS-CB1JF100JY VRS-CB1JF100JY ★ J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J Description 22k 47k 4.7k 39k 270k 68k 1k 1k 10k 10k 2.2k 1M 0 0 0 2.2k 0 390k 0 100k 820 100k 1M 1M 1M 0 10k 1 470 470 100 1 10k 1 68k 8.2k 1.5k 10k 68k 6.8k 1.5k 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10k 1k 4.7k 1k 1k 4.7k 120 120 120 120 10k 10k 10k 10 10 10 10 10 10 10 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/2W 1/16W 1/16W 1/16W 1/2W 1/16W 1/2W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Film Metal Film Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Code AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AA AA AB AA AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA XG-C50X Ref. No. R7068 R7069 R7070 R7071 R7083 R7085 ★ Part No. Description Code Ref. No. ★ Part No. Description DUNTKB171FE01 DUNTKB172DE01 OUTPUT UNIT(Continued) KEY UNIT VRS-CA1JF100JY VRS-CB1JF100JY VRS-CY1JF100JY VRS-CY1JF103JY VRS-TX2HF1R0JY VRS-CY1JF103JY J J J J J J 10 10 10 10k 1 10k 1/16W 1/16W 1/16W 1/16W 1/2W 1/16W Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide TRANSISTORS AA AA AA AA AB AA Q2201 Q2202 Q2203 Q2204 Q2205 SWITCH S2601 QSW-KA001WJZZY J Key Switch Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Plug, 4-pin(SO1) Plug, 4-pin Plug, 13-pin(KY1) Plug, 3-pin(RC) Lead Relay Plug Plug, 11-pin(EB1) Plug, 3-pin(FD) Plug, 30-pin(IA) Plug, 20-pin(IB) Plug, 24-pin(EA) Plug, 2-pin(L1) Plug, 2-pin(L2) Plug, 2-pin(L3) Lug Plug, 80-pin(PCO) Plug, 80-pin(PC1) Socket, 32-pin(RP) Socket, 32-pin(GP) Socket, 32-pin(BP) Cover Angle, x2 Angle, x1 Screw, x3 VSDTC144EUA-1Y J DTC144EUA VSDTC144EUA-1Y J DTC144EUA VSDTC144EUA-1Y J DTC144EUA VSDTC144EUA-1Y J DTC144EUA VSDTC144EUA-1Y J DTC144EUA AB AB AB AB AB DIODES AD D2201 RH-PX0210TAZZY D2202 RH-PX0210TAZZY AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AB AC AB AD AA AA AA AA AD AC AD AC AD AE AC AL AH AD AC AC AC AD AH AH AE AE AE AD AE AG AB D2203 RH-PX0210TAZZY MISCELLANEOUS PARTS FB301 RBLN-0064TAZZY J FB302 RBLN-0064TAZZY J FB1101 RBLN-0059CEZZY J FB1102 RBLN-0059CEZZY J FB1104 RBLN-0059CEZZY J FB1105 RBLN-0059CEZZY J FB1106 RBLN-0059CEZZY J FB1201 RBLN-0059CEZZY J FB1202 RBLN-0059CEZZY J FB1204 RBLN-0059CEZZY J FB1205 RBLN-0059CEZZY J FB1206 RBLN-0059CEZZY J FB1301 RBLN-0059CEZZY J FB1302 RBLN-0059CEZZY J FB1304 RBLN-0059CEZZY J FB1305 RBLN-0059CEZZY J FB1306 RBLN-0059CEZZY J FB2401 RBLN-0059CEZZY J FB2751 RBLN-0062CEZZY J FB2753 RBLN-0059CEZZY J FB4503 RBLN-0061TAZZY J FB7001 RBLN-0065TAZZY J FB7002 RBLN-0065TAZZY J FB7003 RBLN-0065TAZZY J FB7004 RBLN-0065TAZZY J P301 QPLGN0474TAZZY J P1301 QPLGN0463TAZZY J P2601 QPLGN1363TAZZY J P2602 QPLGN0363TAZZY J P2603 QPLGN0198FJZZY J P2751 QPLGN1174TAZZY J P2752 QPLGN0364TAZZY J P3102 QCNCM3021TAZZ J P3602 QCNCM2021TAZZ J P7001 QPLGNA008WJZZ J P7002 QPLGN0264TAZZY J P7003 QPLGN0264TAZZY J P7004 QPLGN0264TAZZY J P7005 QLUGHA001WJZZY J P8001 QCNCMA019WJZZY J P8002 QCNCMA019WJZZY J SC1101 QSOCN3271TAZZY J SC1201 QSOCN3271TAZZY J SC1301 QSOCN3271TAZZY J GCOVHA014WJKZ J LANGTA005WJFW J LANGTA006WJFW J XBPSD30P06R00 J Code J Power Indicator J Lamp Replacement Indicator J Temperature Warning Indicator AC AC AC CAPACITORS C2201 VCKYCY1EF104ZY J 0.1 C2202 VCKYTV1EF104ZY J 0.1 25V 25V Ceramic Ceramic AA AB Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA RESISTORS R2201 R2208 R2210 R2211 R2213 R2214 R2215 R2216 R2217 R2218 R2219 R2220 R2221 R2222 R2223 R2224 R2225 VRS-CY1JF751FY VRS-CY1JF751FY VRS-CY1JF751FY VRS-CY1JF751FY VRS-TW2ED471JY VRS-TW2ED122JY VRS-TW2ED471JY VRS-TW2ED122JY VRS-TW2ED122JY VRS-CY1JF272FY VRS-CY1JF272FY VRS-CY1JF272FY VRS-CY1JF472FY VRS-CY1JF472FY VRS-CY1JF472FY VRS-CY1JF103FY VRS-CY1JF103FY S2201 S2204 S2205 S2206 S2207 S2208 S2209 S2210 S2211 S2212 S2213 S2214 QSW-KA001WJZZY QSW-KA001WJZZY QSW-KA001WJZZY QSW-KA001WJZZY QSW-KA001WJZZY QSW-KA001WJZZY QSW-KA001WJZZY QSW-KA001WJZZY QSW-KA001WJZZY QSW-KA001WJZZY QSW-KA001WJZZY QSW-KA001WJZZY J J J J J J J J J J J J J J J J J 750 750 750 750 470 1.2k 470 1.2k 1.2k 2.7k 2.7k 2.7k 4.7k 4.7k 4.7k 10k 10k 1/16W 1/16W 1/16W 1/16W 1/4W 1/4W 1/4W 1/4W 1/4W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W SWITCHES J J J J J J J J J J J J Power(ON) MENU RIGHT AUTO SYNC DOWN ENTER KEY STONE UNDO LEFT UP Power(OFF) INPUT AD AD AD AD AD AD AD AD AD AD AD AD MISCELLANEOUS PARTS P2201 QPLGN1363TAZZY J P2203 QPLGN0364TAZZY J QCNW-A496WJZZ J QCNW-A899WJZZ J 156 Plug, 13-pin(KYO) Lead Relay Plug Connecting Cord Connecting Cord AD AC AG AD XG-C50X Ref. No. ★ Part No. Description Code Ref. No. ★ Part No. Description DUNTKB173DE01 RUNTKA021WJZZ R/C RECEIVER UNIT AC INLET UNIT DIODES CAPACITORS 6.3V Electrolytic 25V Ceramic AC AA D701 Z701 95KUBA0005KZ 95KUER0002ZZ 1/16W Metal Oxide 1/16W Metal Oxide AA AA L701 L702 95KUKZ1138ZZ 95KUKZ1138ZZ AC AG AD AD C701 C702 C703 C704 C758 C759 95KUGFM474KR 95KUGFM474KR 95KUGZ1016ZZ 95KUGZ1016ZZ 95KUGZ1016ZZ 95KUGZ1016ZZ R701 R702 95KUEEC105CH 95KUEBZ3R9J RL701 MT701 MD702 SC701 SC702 SC703 F701 CN701 CN702 CN703 CN709 95KPHZ0205ZZ 95KLRZ6866ZQ 95KGZZ5491ZZ 95KRAA3060AZ 95KRAB3060AB 95KRAZ4141ZT 95KPJCTP1002 95KPZZ1018ZZ 95KPCZ0278ZZ 95KPKZ0741ZZ 95KEDB7717ZZ C5591 VCEASM0JW107MY J 100 C5592 VCKYCY1EF104ZY J 0.1 J 470 J 22 J J J J Plug, 3-pin(RC) R/C Receiver Shield Connecting Cord AB J Inductor J Inductor CAPACITORS MISCELLANEOUS PARTS P5591 QPLGN0363TAZZY RMC5591 RRMCU0239CEZZ PSLDC3117CEFW QCNW-A495WJZZ J Diode J Varistor COILS RESISTORS R5591 VRS-CY1JF471JY R5592 VRS-CY1JF220JY Code J J J J J J 0.47 275V Film 0.47 275V Film 4700p Ceramic 4700p Ceramic 4700p Ceramic 4700p Ceramic AD AD AD AD RESISTORS J 470k 1/2W J 3.9 5W Metal Oxide AB Fuse Resistor MISCELLANEOUS PARTS 157 J J J J J J J J J J J Relay Angle Shide Socket Socket Socket Fuse, 10A/250V Inlet Connector, 3-pin Connector, 2-pin Connector AA AB XG-C50X Ref. No. ★ Part No. Description Code RUNTKA026WJZZ FAN UNIT INTEGRATED CIRCUITS IC381 IC7201 IC7202 IC7203 IC7204 IC7205 VHiTDA7056A-1 VHiPQ20WZ11-1Y VHiPQ20WZ11-1Y VHiPQ20WZ11-1Y VHiPQ20WZ11-1Y VHiPQ20WZ11-1Y J J J J J J TDA7056A PQ20WZ1U PQ20WZ1U PQ20WZ1U PQ20WZ1U PQ20WZ1U AP AF AF AF AF AF TRANSISTORS Q7201 VS2SA1036KR-1Y Q7202 VS2SC3928AR-1Y J 2SA1036KT146R J 2SC3928AR VHDDAN202K/-1Y VHDDAN202K/-1Y VHDDAN202K/-1Y VHDDAN202K/-1Y VHDDAN202K/-1Y VHDDAN202K/-1Y VHDDAN202K/-1Y VHDDAN202K/-1Y VHDDAN202K/-1Y J J J J J J J J J C831 C382 C384 C385 C7201 C7202 C7203 C7204 C7205 C7206 C7207 C7208 C7209 C7210 VCKYCY1EF104ZY J VCEASM1CW107MYJ VCEASM1CW106MYJ VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCKYCY1EF104ZY J VCEASM1CW107MYJ VCEASM1CW476MYJ VCEASM1CW476MYJ VCEASM1CW476MYJ VCEASM1CW476MYJ VCEASM1CW476MYJ VCEASM1CW226MYJ VCE9PF1CW336MY J R381 R382 R384 R7202 R7203 R7204 R7206 R7207 R7209 R7210 R7211 R7212 R7215 R7216 R7217 R7219 R7220 R7222 R7223 R7224 R7225 R7227 R7229 R7230 R7231 R7232 R7233 R7234 R7235 R7236 R7237 VRS-CY1JF102JY VRS-TX2HF8R2JY VRS-CY1JF681Y VRS-CY1JF103JY VRS-CY1JF822FY VRS-CY1JF332FY VRS-CY1JF273JY VRS-CY1JF103FY VRS-CY1JF103JY VRS-CY1JF822FY VRS-CY1JF302FY VRS-CY1JF104FY VRS-CY1JF103JY VRS-CY1JF822FY VRS-CY1JF332FY VRS-CY1JF273JY VRS-CY1JF103FY VRS-CY1JF103JY VRS-CY1JF682FY VRS-CY1JF272FY VRS-CY1JF823FY VRS-CY1JF103FY VRS-CY1JF103JY VRS-CY1JF682FY VRS-CY1JF332FY VRS-CY1JF105FY VRS-CY1JF183FY VRS-CY1JF103FY VRS-CY1JF472JY VRS-CY1JF472JY VRS-CY1JF472JY DAN202KT146 DAN202KT146 DAN202KT146 DAN202KT146 DAN202KT146 DAN202KT146 DAN202KT146 DAN202KT146 DAN202KT146 AB AB AB AB AB AB AB AB AB 25V 16V 16V 25V 25V 25V 16V 16V 16V 16V 16V 16V 16V 16V Ceramic Electrolytic Electrolytic Ceramic Ceramic Ceramic Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Elect. (N.P) AC AD AC AA AA AA AD AC AC AC AC AC AC AD 1/16W 1/2W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide AA AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA RESISTORS J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 1k 8.2 680 10k 8.2k 3.3k 27k 10k 10k 8.2k 3k 100k 10k 8.2k 3.3k 27k 10k 10k 6.8k 2.7k 82k 10k 10k 6.8k 3.3k 1M 18k 10k 4.7k 4.7k 4.7k ★ R7239 R7240 R7241 R7244 R7245 R7246 R7247 R7248 R7249 R7250 R7251 R7252 R7255 VRS-CY1JF472JY VRS-CY1JF472JY VRS-CY1JF472JY VRS-CY1JF103JY VRS-CY1JF000JY VRS-CY1JF103JY VRS-CY1JF273JY VRS-CY1JF103JY VRS-CY1JF103JY VRS-CY1JF272JY VRS-CY1JF222JY VRS-CY1JF103FY VRS-CY1JF333FY J J J J J J J J J J J J J FB381 FB7201 FB7202 FB7203 FB7204 FB7205 FB7206 FB7207 FB7208 FB7209 FB7210 FB7211 FB7212 FB7213 FB7214 FB7215 FB7216 FB7217 FB7218 P381 P382 P7201 P7202 P7203 P7204 P7205 P7206 P7207 P7208 P7209 P7210 RBLN-0064TAZZY RBLN-0062CEZZY RBLN-0062CEZZY RBLN-0062CEZZY RBLN-0062CEZZY RBLN-0062CEZZY RBLN-0059CEZZY RBLN-0062CEZZY RBLN-0059CEZZY RBLN-0062CEZZY RBLN-0059CEZZY RBLN-0210TAZZY RBLN-0059CEZZY RBLN-0210TAZZY RBLN-0059CEZZY RBLN-0210TAZZY RBLN-0059CEZZY RBLN-0210TAZZY RBLN-0059CEZZY QPLGN0474TAZZY QPLGN0539FJZZY QPLGN1174TAZZY QPLGN0363TAZZY QPLGN0263AZZY QPLGN0458REZZY QPLGN0565FJZZY QPLGN0566FJZZY QPLGN0463TAZZY QPLGN0364TAZZY QPLGN0364TAZZY QPLGN0566FJZZY Description 4.7k 4.7k 4.7k 10k 0 10k 27k 10k 10k 2.7k 2.2k 10k 33k 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Metal Oxide Code AA AA AA AA AA AA AA AA AA AA AA AA AA MISCELLANEOUS PARTS CAPACITORS 0.1 100 10 0.1 0.1 0.1 100 47 47 47 47 47 22 33 Part No. AC AB DIODES D7201 D7202 D7203 D7204 D7205 D7206 D7207 D7208 D7209 Ref. No. 158 J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Plug, 4-pin (SOO) Plug, 2-pin (SP) Plug, 11-pin (EBO) Plug, 3-pin (RT) Plug, 2-pin (PT) Plug, 4-pin (FL) Plug, 3-pin (FP) Plug, 4-pin (FI) Plug, 4-pin (FR) Plug, 3-pin (FG) Plug, 3-pin (FB) Plug, 4-pin (FE) AB AC AC AC AC AC AB AC AB AC AB AB AB AB AB AB AB AB AB AD AD AE AC AB AD AD AD AC AC AC AD XG-C50X Ref. No. Part No. ★ Description Code Ref. No. RDENCA011WJZZ INTEGRATED CIRCUITS 95KUCB0237AZ 95KUCY0006AM 95KUCY0136AZ 95KUCY0021AK 95KUCC0013DZ 95KUCY0116AK 95KUCY0006AM 95KUCY0021AK 95KUCY0149AK 95KUAG0236AZ 95KUAG0236AZ J J J J J J J J J J J MIP290 UPC1093T FA5501N M5233FP UPC78N12H FA3641N UPC1093T M5233FP FA7703 SI4431ADY SI4431ADY 95KUAG0226AB 95KUAY0041AM 95KUAG0226AB 95KUAY0041AM 95KUAG0146DZ 95KUAY0012AK 95KUAY0013AK 95KUAY0013AK 95KUAY0013AM 95KUAD0132AK 95KUAY0136AK 95KUAD0132AK 95KUAY0136AK D702 D703 D704 D705 D706 D707 D708 D709 D710 D711 D712 D713 D714 D715 D716 D717 D718 D719 D720 D721 D722 D723 D7701 D7702 ZD701 ZD702 ZD703 ZD704 ZD705 ZD707 ZD708 ZD706 95KUBY0088AK 95KUBY0020AK 95KUBB0206EZ 95KUBY0033BK 95KUBY0033BK 95KUBC0284BZ 95KUBY0020AK 95KUBY0047AK 95KUBY0045AK 95KUBY0045AK 95KUBY0020AK 95KUBY0020AK 95KUBA0039AZ 95KUBB0166BZ 95KUBC0264BE 95KUBB0194AZ 95KUBC0125DK 95KUBY0043AK 95KUBC0125DK 95KUBC0125DK 95KUBY0020AK 95KUBC0163BK 95KUBY0068AZ 95KUBY0068AZ 95KUBDAK8R2B 95KUBXAD6R2C 95KUBXAD150A 95KUBXAD180A 95KUBXAD270A 95KUBXAD3R3C 95KUBXBK3R9C 95KUBLBL170A PC701 PC702 PC703 PC704 95KUDC0163BB 95KUDC0163BB 95KUDC0163BB 95KUDC0163BB J J J J J J J J J J J J J FS14KM-12A 2SA1797 FS14KM-12A 2SA1797 2SK2480 2SA812 2SC1623 2SC1623 2SC1623 2SD2150 2SB1424 2SD2150 2SB1424 AF AM Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Diode Zener Diode Diode Zener Diode Diode Zener Diode Zener Diode Diode Zener Diode Diode Diode Zener Diode Zener Diode Zener Diode Zener Diode Zener Diode Zener Diode Zener Diode Zener Diode J J J J Photo Coupler Photo Coupler Photo Coupler Photo Coupler 95KUKZ0789ZZ 95KUKZ1141ZZ 95KUKZ1140ZZ 95KULZ1142ZZ 95KULZ1142ZZ T701 T702 T703 95K829205033 95KUKZ1139ZZ 95K829205032 å AG AF J J J J J Inductor Inductor Inductor Coil Coil J Transformer J Transformer J Transformer CONTROL VR701 95KUFBA224DB J Control CAPACITORS AB AB AB AC AN AP AC AC AC AC AD AG AB AB AB AC AB AD AD å å PACKAGED CIRCUITS å å å å L703 L704 L705 L7701 L7702 TRANSFORMERS å DIODES J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J Code AG TRANSISTORS Q701 Q702 Q703 Q704 Q705 Q706 Q707 Q708 Q7701 Q7702 Q7703 Q7704 Q7705 Description COILS POWER UNIT IC701 IC702 IC703 IC704 IC705 IC706 IC707 IC708 IC7701 IC7702 IC7703 ★ Part No. AH AH AH AH 159 C705 C706 C707 C708 C710 C712 C713 C714 C715 C716 C717 C718 C719 C720 C721 C722 C723 C724 C725 C726 C727 C728 C729 C730 C731 C732 C733 C734 C736 C737 C738 C739 C741 C743 C744 C745 C746 C747 C748 C749 C750 C751 C752 C753 C754 C755 C757 C761 C762 C763 C7701 C7702 C7703 C7704 C7705 C7706 C7707 C7708 95KUGA0439ZZ 95KUGA0440ZZ 95KUGXGFD104 95KUGXGCF103 95KUGA0429ZZ 95KUGZ1336ZZ 95KUGXGCF102 95KUGXAED474 95KUGXGCF103 95KUGXKEF224 95KUGXGCF103 95KUGXGFD333 95KUGXGCF102 95KUGA0441ZZ 95KUGCU102EM 95KUGA0431ZZ 95KUGCU102EM 95KUGA0432ZZ 95KUGCU472BW 95KUGA0441ZZ 95KUGZ1251ZZ 95KUGXGCF472 95KUGXKHB106 95KUGXGCF102 95KUGXAED224 95KUGXAED474 95KUGXGFD104 95KUGXGCF152 95KUGXKJT102 95KUGA0433ZZ 95KUGA0433ZZ 95KUGA0434ZZ 95KUGA0435ZZ 95KUGA0436ZZ 95KUGXGFD104 95KUGA0249ZZ 95KUGA0249ZZ 95KUGA0437ZZ 95KUGXHEA105 95KUGXHEA105 95KUGXGFD104 95KUGXGFD104 95KUGXHEA105 95KUGXGFD104 95KUGXGCF102 95KUGZ1016ZZ 95KUGXGFD104 95KUGZ1016ZZ 95KUGXKMS101 95KUGXKMS101 95KUGXKKD106 95KUGXKHB106 95KUGXGCC104 95KUGXGFD473 95KUGXKHB105 95KUGXGFD104 95KUGXKHB106 95KUGXGFD473 J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 3.3 150 0.1 0.01 820 2.2 0.001 0.47 0.01 0.22 0.01 0.033 0.001 39 1000p 330 1000p 56 4700p 39 47p 0.0047 10 1000p 0.22 0.47 0.1 1500p 1000p 1000 1000 56 220 680 0.1 100 100 68 1 1 0.1 0.1 1 0.1 1000p 4700p 0.1 4700p 100p 100p 10 10 0.1 0.047 1 0.1 10 0.047 400V 6.3V 50V 50V 6.3V 450V 50V 25W 50V 25V 50V 25V 1kV 35V 1kV 220V 1kV 25V 1kV 35V 2kV 50V 10V 50V 25V 25V 25V 50V 630V 10V 16V 16V 25V 16V 25V 10V 10V 25V 6.3V 6.3V 50V 25V 6.3V 25V 50V 50V 25V 50V 500V 500V 25V 10V 16V 16V 10V 25V 10V 16V Electrolytic Electrolytic Ceramic Ceramic Electrolytic Film Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Ceramic Electrolytic Ceramic Electrolytic Ceramic Electrolytic Ceramic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Electrolytic Electrolytic Electrolytic Electrolytic Ceramic Electrolytic Electrolytic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic AD AD AD XG-C50X Ref. No. ★ Part No. Description Code RDENCA011WJZZ POWER UNIT (Continued) RESISTORS R703 R704 R705 R706 R708 R710 R711 R712 R713 R714 R715 R716 R717 R718 R719 R720 R721 R722 R723 R724 R725 R726 R727 R728 R729 R730 R731 R732 R733 R734 R735 R736 R737 R738 R739 R740 R741 R742 R743 R744 R745 R746 R747 R748 R749 R750 R751 R752 R753 R754 R756 R757 R758 R759 R760 R761 R762 R765 R766 R767 R768 R769 R770 R771 R772 R773 R774 R775 R776 R777 95KUEXBAH221 95KUEXBAH122 95KUEYCH1003 95KUEYCH1003 95KUEYCH1002 95KUESGR15DT 95KUEXDAK100 95KUEXDAK100 95KUEXDAK474 95KUEXDAK474 95KUEXDAK394 95KUEXBAH123 95KUEXDAK684 95KUEXDAK564 95KUEXDAK564 95KUEXBAH133 95KUEXBAH181 95KUEXBAH223 95KUEXBAH103 95KUEXBAH681 95KUEXDAK334 95KUEXDAK334 95KUEXDAK334 95KUEXBAH153 95KUEXBAH822 95KUEXBAH124 95KUEXBAH332 95KUEXBAH332 95KUEXBAH123 95KUESGR15DT 95KUEFE154EG 95KUEXDAK563 95KUEXDAK563 95KUEXDAK563 95KUEBCR47AG 95KUEXJAPR22 95KPZZ0605ZZ 95KPZZ0605ZZ 95KUEXBAH223 95KUEXBAH103 95KUEXBAH273 95KUEXDAK000 95KUEXDAK100 95KUEXDAK151 95KUEXBAS101 95KUEXBAS331 95KUEXBAH472 95KUEXBAH391 95KUEXBAH473 95KUEXBAH103 95KUEXBAH222 95KUEXBAH000 95KUEXBAH122 95KUEYBG2202 95KUEYBG4701 95KUEXDAK122 95KUEXBAH104 95KUEXBAH152 95KUEXBAH122 95KUEYCH2703 95KUEXBAH122 95KUEXBAH103 95KUEXBAH122 95KUEXBAH104 95KUEXBAH103 95KUEXBAH103 95KUEXBAH103 95KUEBCR10AG 95KUEXBAH103 95KUEXBAH163 J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 220 1/16W 1.2k 1/16W 100k 1/16W 100k 1/16W 10k 1/16W 0.15 5W 10 1/4W 10 1/4W 470k 1/4W 470k 1/4W 390k 1/4W 12k 1/16W 680k 1/4W 560k 1/4W 560k 1/4W 13k 1/16W 82 1/16W 22k 1/16W 10k 1/16W 330 1/16W 330k 1/4W 15k 1/4W 330k 1/4W 15k 1/16W 8.2k 1/16W 120k 1/16W 6.2k 1/16W 3.3k 1/16W 10k 1/16W 0.15 5W 150k 1/2W 560k 1/8W 560k 1/8W 560k 1/8W 0.47 1/2W 0.22 1/2W 0 1/16W 0 1/16W 22k 1/16W 10k 1/16W 27k 1/16W 0 1/4W 10 1/4W 150 1/16W 100 1/16W 330 1/16W 4.7k 1/16W 390 1/16W 47k 1/16W 10k 1/16W 2.2k 1/16W 0 1/10W 1.2k 1/16W 22k 1/8W 4.7k 1/4W 1.2k 1/4W 100k 1/16W 1.5k 1/16W 1.2k 1/16W 330k 1/16W 1.2k 1/16W 11k 1/16W 1.3k 1/16W 100k 1/16W 10k 1/16W 10k 1/16W 10k 1/16W 1 1/2W 10k 1/16W 16k 1/16W Chip Chip Chip Chip Chip Chip Chip Chip Chip Chip Chip Chip Chip Chip Chip Chip Chip Chip Chip Chip Chip Chip Chip Chip Chip Chip Chip Chip Chip Chip Chip Chip AB Chip AB Chip AB Fuse Resistor Chip Chip AA Chip AA Chip Chip Chip Chip AB Chip Chip Chip Chip Chip Chip Chip Chip Chip Chip Chip Chip Chip Chip AB Chip Chip Chip Chip Chip Chip Chip Chip Chip Chip Chip Fuse Resistor AE Chip Chip Ref. No. Part No. ★ R778 R779 R780 R782 R783 R784 R785 R7701 R7702 R7703 R7704 R7705 R7706 R7707 R7708 R7709 R7710 R7711 R7712 R7713 R7714 R7715 R7716 R7717 R7718 R7719 R7720 R7723 R7724 J701 J702 J7701 J7702 95KUEXBAH164 95KUEXBAH103 95KUEXBAH122 95KUEXBAH122 95KUEXBAH122 95KUEXDAK563 95KUEXDAK563 95KUEXBAH123 95KUEXBAH123 95KUEXBAH682 95KUEXBAH153 95KUEXBAH102 95KUEYCH2701 95KUEYCH1201 95KUEXBAH123 95KUEXBAH102 95KUEYCH1501 95KUEYCH1001 95KUEXBAH103 95KUEXBAH682 95KUEXBAH103 95KUEXDAK121 95KUEXDAK100 95KUEXDAK121 95KUEXDAK100 95KUEYCH3300 95KUEYCH2700 95KUEXBAH000 95KUEXBAH470 95KUEXCAS000 95KUEXCAS000 95KUEXBAH000 95KUEXBAH000 J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J FB701 FB702 FB703 FB704 FB706 FB707 FB708 FB709 FB710 F703 CN704 CN-B704 CN705 CN706 CN707 CN708 ET701 RL702 MT702 MT703 MT704 MD704 SC704 SC705 95KBFZ89547Z 95KBFZ89547Z 95KUKY0014AZ 95KUKY0014AZ 95KUKY0014AZ 95KUKZ0828ZZ 95KUKY0014AZ 95KUKY0014AZ 95KUKY0014AZ 95KPJT0160ZZ 95KPKZ1102ZZ 95KECB8034ZZ 95KECB8060ZZ 95KPKZ1135ZZ 95KECB8036ZZ 95KECB8037ZZ 95KFBZ0098ZZ 95KPHZ0206ZZ 95KLRZ6926ZZ 95KLRZ6868ZR 95KLRZ6869ZR 95KGZZ5492ZZ 95KRAZ3211ZB 95KRBA3024ZB Description 160k 1/16W Chip 10k 1/16W Chip 1.2k 1/16W Chip 1.2k 1/16W Chip 1.2k 1/16W Chip 56k 1/8W Chip 56k 1/8W Chip 12k 1/16W Chip 12k 1/16W Chip 6.8k 1/16W Chip 15k 1/16W Chip 1k 1/16W Chip 2.7k 1/16W Chip 1.2k 1/16W Chip 12k 1/16W Chip 1k 1/16W Chip 1.5k 1/16W Chip 1k 1/16W Chip 12k 1/16W Chip 6.8k 1/16W Chip 10k 1/16W Chip 120 1/8W Chip 10 1/8W Chip 120 1/8W Chip 10 1/8W Chip 330 1/16W Chip 270 1/16W Chip 0 1/16W Chip 47 1/16W Chip 0 1/8W Chip 0 1/8W Chip 0 1/16W Jumper 0 1/16W Jumper Code AB AB AB AB MISCELLANEOUS PARTS å å 160 J J J J J J J J J J J J J J J J J J J J J J J J Ferrite Bead Ferrite Bead Ferrite Bead Ferrite bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Ferrite Bead Fuse P130A Plug, 3-pin Plug, 3-pin Plug, 5-pin Plug, 3-pin Plug, 2-pin Plug, 24-pin Terminal Relay Heat Sink Heat Sink Heat Sink Insulating Barrier Screw, x8 Nut, x2 AD AD AD AC AD AD AD AF AC AC AA AA XG-C50X Ref. No. ★ Part No. Description Code Ref. No. CPCi-A002CE01 C8014 C8015 C8016 C8017 C8018 C8019 C8020 C8021 C8022 C8023 C8024 C8025 C8026 C8027 C8028 C8029 C8030 C8031 C8033 C8035 C8038 C8039 C8040 C8041 C8042 C8043 C8044 C8045 C8046 C8047 C8048 C8049 C8050 C8051 C8052 C8053 C8054 C8055 C8056 C8057 C8058 C8059 C8060 C8062 C8063 C8064 C8065 C8066 C8069 C8070 C8071 C8072 C8073 C8074 C8075 C8076 C8077 C8078 C8085 C8082 C8083 C8140 C8141 C8142 C8150 C8151 C8152 C8153 C8154 C8155 C8156 C8157 C8158 C8159 C8160 PC I/F UNIT INTEGRATED CIRCUITS IC8003 IC8004 IC8005 IC8006 IC8007 IC8008 IC8010 IC8013 IC8015 IC8025 IC8028 IC8029 IC8030 IC8319 IC8320 IC8321 IC8322 IC8363 IC8364 IC8365 IC8366 9DK001-11020 9DK001-15115 RH-iXA372WJZZQ 9DK001-15118 RH-iXA147WJZZQ 9DK001-15112 9DK001-15117 9DK001-15113 9DK001-15119 RH-iXA091WJZZQ 9DK001-11028 RH-iX3399CEN1Q 9DK001-11028 9DK001-11024 9DK001-11024 9DK001-11024 9DK001-11024 9DK001-12107 9DK001-15114 9DK001-12103 9DK001-12105 J J J J J J J J J J J J J J J J J J J J J AT24C128N-10SC PQ05VY3H3Z LH28F640BFE-PBTL90 PST9229 HD6417709ABP133V PQ033EZ01 PST9222 AD9888-170 SAA7118E CVIC2(MB87M1370TB-G) HY57V641620HGT-H IX3399 HY57V641620HGT-H HY57V653220BTC-7 HY57V653220BTC-7 HY57V653220BTC-7 HY57V653220BTC-7 74VHC153MTC PQ070XZ01 74LCX157MTC 74LVX125MTC AS AM BE AL BK AM AK BT BM BX AY BM AY BN BN BN BN AK AN AK AK TRANSISTORS Q8002 9DK001-20012 Q8005 9DK001-20012 J 2SA1037AKQ J 2SA1037AKQ AE AE DIODES D8005 9DK001-30018 D8009 9DK001-30018 D8035 9DK001-30018 J 1SS187(D3) J 1SS187(D3) J 1SS187(D3) AD AD AD PACKAGED CIRCUITS X8001 X8004 X8005 X8006 X8007 9DK001-80038 9DK001-80027 9DK001-80039 9DK001-80034 9DK001-80015 FL8001 FL8002 FL8003 FL8041 FL8094 FL8103 FL8098 FL8099 FL8110 FL8114 L8003 L8004 L8005 L8006 L8011 L8012 L8013 L8014 L8015 L8022 9DK001-50121 9DK001-50110 9DK001-81020 9DK001-81020 9DK001-81020 9DK001-81020 9DK001-50110 9DK001-50110 9DK001-50110 9DK001-50110 9DK001-81059 9DK001-81059 9DK001-81059 9DK001-81062 9DK001-81059 9DK001-81059 9DK001-81062 9DK001-81059 9DK001-81062 9DK001-81059 C8003 C8004 C8005 C8007 C8008 C8009 C8010 C8012 C8013 9DK001-42157 9DK001-42099 9DK001-42161 9DK001-42156 9DK001-42157 9DK001-42157 9DK001-42160 9DK001-42103 9DK001-42103 J J J J J Crystal, 16.588MHz Crystal, 25.000MHz Crystal, 37.500MHz Crystal, 24.576MHz Crystal, 32.768kHz AN AR AR AN AS FILTERS AND COILS J J J J J J J J J J J J J J J J J J J J 10 1/10W Chip 2125 0 1/10W Chip 2125 Filter BMK351 Filter BMK351 Filter BMK351 Filter BMK351 0 1/10W Chip 2125 0 1/10W Chip 2125 0 1/10W Chip 2125 0 1/10W Chip 2125 NLC322522T 1.0µH NLC322522T 3.3µH NLC322522T 3.3µH BLM21P221SG NLC322522T 3.3µH NLC322522T 3.3µH BLM21P221SG NLC322522T 3.3µH BLM21P221SG NLC322522T 3.3µH AB AB AG AG AG AG AB AB AB AB AE AE AE AE AE AE AE AE AE AE CAPACITORS J J J J J J J J J 0.1 100p 0.047 1 0.1 0.1 10 15p 15p 25V 50V 25V 10V 25V 25V 6.3V 50V 50V Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic AC AC AB AC AC AC AB AC AC 161 Part No. 9DK001-42156 9DK001-42160 9DK001-42157 9DK001-42156 9DK001-42163 9DK001-42104 9DK001-42104 9DK001-40081 9DK001-42156 9DK001-42156 9DK001-42157 9DK001-42160 9DK001-42157 9DK001-42161 9DK001-42161 9DK001-42161 9DK001-42157 9DK001-42156 9DK001-42156 9DK001-40089 9DK001-42161 9DK001-40089 9DK001-42161 9DK001-42161 9DK001-40091 9DK001-42161 9DK001-42161 9DK001-42161 9DK001-42103 9DK001-42103 9DK001-40081 9DK001-42157 9DK001-40081 9DK001-42156 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-40091 9DK001-42161 9DK001-42161 9DK001-42157 9DK001-42161 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-40091 9DK001-42096 9DK001-42161 9DK001-42096 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42161 9DK001-42157 9DK001-42162 9DK001-40081 9DK001-42161 9DK001-42161 9DK001-42161 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 ★ J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J Description 1 10 0.1 1 1000p 470p 470p 22 1 1 0.1 10 0.1 0.047 0.047 0.047 0.1 1 1 47 0.047 47 0.047 0.047 100 0.047 0.047 0.047 15p 15p 22 0.1 22 1 0.1 0.1 0.1 0.1 0.1 100 0.047 0.047 0.1 0.047 0.1 0.1 0.1 100 0.01 0.047 0.01 0.1 0.1 0.1 0.1 0.1 0.1 0.047 0.1 0.33 22 0.047 0.047 0.047 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 10V 6.3V 25V 10V 25V 50V 50V 6.3V 10V 10V 25V 6.3V 25V 25V 25V 25V 25V 10V 10V 6.3V 25V 6.3V 25V 25V 4V 25V 25V 25V 50V 50V 6.3V 25V 6.3V 10V 25V 25V 25V 25V 25V 4V 25V 25V 25V 25V 25V 25V 25V 4V 50V 25V 50V 25V 25V 25V 25V 25V 25V 25V 25V 10V 6.3V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Ceramic Electrolytic Ceramic Ceramic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Ceramic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Code AC AB AC AC AC AC AC AF AC AC AC AB AC AB AB AB AC AC AE AE AB AE AB AB AF AB AB AB AC AC AF AC AF AC AC AC AC AC AF AF AB AB AC AB AC AC AC AF AC AB AC AC AC AC AC AC AC AB AC AB AF AB AB AB AC AC AC AC AC AC AC AC AC AC AC XG-C50X Ref. No. Part No. ★ Description Code Ref. No. CPCi-A002CE01 PC I/F UNIT (Continued) C8161 C8162 C8163 C8164 C8165 C8166 C8167 C8169 C8170 C8171 C8174 C8176 C8177 C8192 C8197 C8205 C8214 C8218 C8366 C8375 C8575 C8576 C8577 C8578 C8579 C8580 C8581 C8582 C8583 C8584 C8585 C8586 C8589 C8590 C8591 C8592 C8593 C8594 C8595 C8596 C8597 C8598 C8599 C8600 C8601 C8602 C8603 C8607 C8609 C8611 C8613 C8615 C8617 C8619 C8621 C8623 C8625 C8627 C8629 C8631 C8633 C8635 C8637 C8638 C8640 C8641 C8648 C8649 C8656 C8658 C8662 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42158 9DK001-42159 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-40091 9DK001-40091 9DK001-42157 9DK001-42156 9DK001-42156 9DK001-42156 9DK001-42156 9DK001-42157 9DK001-42156 9DK001-42156 9DK001-42156 9DK001-42157 9DK001-42157 9DK001-42156 9DK001-42156 9DK001-42156 9DK001-42156 9DK001-42156 9DK001-42156 9DK001-42157 9DK001-42157 9DK001-42156 9DK001-42157 9DK001-42156 9DK001-42156 9DK001-42157 9DK001-42157 9DK001-40091 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 0.1 0.1 0.1 0.1 0.1 3900p 0.039 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 100 100 0.1 1 1 1 1 0.1 1 1 1 0.1 0.1 1 1 1 1 1 1 0.1 0.1 1 0.1 1 1 0.1 0.1 100 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 25V 25V 25V 25V 25V 16V 16V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 4V 4V 25V 10V 10V 10V 10V 25V 10V 10V 10V 25V 25V 10V 10V 10V 10V 10V 10V 25V 25V 10V 25V 10V 10V 25V 25V 4V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V Ceramic Ceramic Ceramic Ceramic Ceramic Film Film Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic AC AC AC AC AC AL AG AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC ★ Part No. J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J Description C8666 C8668 C8670 C8672 C8678 C8682 C8685 C8686 C8687 C8688 C8689 C8697 C8708 C8759 C8901 C8904 C8905 C8906 C8910 C8915 C8916 C8918 C8920 C8923 C8924 C8930 C8902 C8909 C8911 C8912 C8913 C8914 C8917 C8919 C8921 C8922 C8925 C8927 C8928 C8931 C8932 9DK001-42096 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-40090 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42115 9DK001-42157 9DK001-42115 9DK001-42157 9DK001-42157 9DK001-42157 9DK001-42156 9DK001-42156 9DK001-42156 9DK001-42156 9DK001-42156 9DK001-42156 9DK001-42156 9DK001-40110 9DK001-40091 9DK001-42162 9DK001-42160 9DK001-40091 9DK001-40091 9DK001-42161 9DK001-42156 0.01 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 47 0.1 0.1 0.1 0.1 0.1 0.1 0.1 10p 0.1 10p 0.1 0.1 0.1 1 1 1 1 1 1 1 68 100 0.33 10 100 100 0.047 1 R8001 R8002 R8003 R8008 R8011 R8017 R8018 R8022 R8025 R8026 R8027 R8028 R8029 R8032 R8035 R8036 R8037 R8038 R8039 R8040 R8041 R8042 R8045 R8046 R8047 R8048 R8054 R8063 R8064 R8067 R8069 R8073 9DK001-51030 9DK001-50149 9DK001-50179 9DK001-51030 9DK001-51045 9DK001-50183 9DK001-50186 9DK001-51030 9DK001-51030 9DK001-51037 J J J J J J J J J J 10k 0 2.2k 10k 100 4.7k 22k 10k 10k 6.8k 9DK001-50149 9DK001-50275 9DK001-50150 9DK001-50149 9DK001-50177 9DK001-50159 9DK001-50150 9DK001-50150 9DK001-50044 9DK001-50275 9DK001-50159 9DK001-50044 9DK001-50275 9DK001-50159 9DK001-50044 9DK001-50149 9DK001-50236 9DK001-50213 9DK001-51037 9DK001-50149 9DK001-50185 J J J J J J J J J J J J J J J J J J J J J 0 6.8 10 0 1k 22 10 10 68 6.8 22 68 6.8 22 68 0 910 2k 6.8k 0 10k 50V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 4V 25V 25V 25V 25V 25V 25V 25V 50V 25V 50V 25V 25V 25V 10V 10V 10V 10V 10V 10V 10V 4V 4V 10V 6.3V 4V 4V 25V 10V Code Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Ceramic Electrolytic Electrolytic Ceramic Ceramic Electrolytic Electrolytic Ceramic Ceramic AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AC AM AF AB AB AF AF AB AC 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W Resistor Array Chip 1608 Chip 1608 Resistor Array Resistor Array Chip 1608 Chip 1608 Resistor Array Resistor Array Resistor Array AD AB AA AD AB AA AA AD AD AD 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/10W 1/16W 1/16W 1/10W 1/16W 1/16W 1/10W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W Chip 1608 Chip 1608 Chip 1608 Chip 1608 Chip 1608 Chip 1608 Chip 1608 Chip 1608 Chip 2125 Chip 1608 Chip 1608 Chip 2125 Chip 1608 Chip 1608 Chip 2125 Chip 1608 Chip 1608 Chip 1608 Resistor Array Chip 1608 Chip 1608 AB AB AA AB AA AA AA AA AB AB AA AB AB AA AB AB AB AB AD AB AA RESISTORS 162 XG-C50X Ref. No. Part No. ★ Description Code Ref. No. CPCi-A002CE01 R8997 9DK001-50149 R8998 9DK001-50177 R8999 9DK001-50303 PC I/F UNIT (Continued) R8074 R8075 R8080 R8083 R8088 R8091 R8096 R8097 R8104 R8107 R8109 R8110 R8114 R8117 R8121 R8122 R8134 R8138 R8139 R8140 R8143 R8152 R8153 R8155 R8156 R8157 R8158 R8159 R8160 R8161 R8162 R8165 R8166 R8170 R8172 R8174 R8176 R8178 R8180 R8199 R8201 R8500 R8503 R8509 R8510 R8511 R8512 R8513 R8521 R8552 R8654 R8688 R8690 R8692 R8693 R8694 R8695 R8696 R8697 R8698 R8699 R8700 R8701 R8800 R8801 R8867 R8868 R8869 R8994 R8995 R8996 9DK001-50185 9DK001-50159 9DK001-50044 9DK001-50159 9DK001-50044 9DK001-50159 9DK001-50044 9DK001-50185 9DK001-50149 9DK001-50149 9DK001-51037 9DK001-51037 9DK001-50303 9DK001-50298 9DK001-50292 9DK001-50292 9DK001-50149 9DK001-50177 9DK001-50177 9DK001-50177 9DK001-50177 9DK001-42161 9DK001-42161 9DK001-42161 9DK001-42161 9DK001-50159 9DK001-42161 9DK001-42161 9DK001-42161 9DK001-50149 9DK001-50183 9DK001-50181 9DK001-50149 9DK001-50149 9DK001-50185 9DK001-50149 9DK001-50224 9DK001-50185 9DK001-50149 9DK001-51037 9DK001-50149 9DK001-50149 9DK001-50185 9DK001-50149 9DK001-50149 9DK001-50149 9DK001-50149 9DK001-50149 9DK001-51030 9DK001-50161 9DK001-50204 9DK001-50149 9DK001-50173 9DK001-50149 9DK001-50149 9DK001-50149 9DK001-50149 9DK001-50185 9DK001-50185 9DK001-50185 9DK001-50185 9DK001-50218 9DK001-50257 9DK001-50149 9DK001-50205 9DK001-50275 9DK001-50275 9DK001-50275 9DK001-50236 9DK001-50199 9DK001-50149 J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J 10k 1/16W 22 1/16W 68 1/10W 22 1/16W 68 1/10W 22 1/16W 68 1/10W 10k 1/16W 0 1/16W 0 1/16W 6.8k 1/16W 6.8k 1/16W 39 1/10W 120 1/4W 8.2 1/4W 8.2 1/4W 0 1/16W 1k 1/16W 1k 1/16W 1k 1/16W 1k 1/16W 0.047 25V 0.047 25V 0.047 25V 0.047 25V 22 1/16W 0.047 25V 0.047 25V 0.047 25V 0 1/16W 4.7k 1/16W 3.3k 1/16W 0 1/16W 0 1/16W 10k 1/16W 0 1/16W 150 1/4W 10k 1/16W 0 1/16W 6.8k 1/16W 0 1/16W 0 1/16W 10k 1/16W 0 1/16W 0 1/16W 0 1/16W 0 1/16W 0 1/16W 10k 1/16W 47 1/16W 150 1/16W 0 1/16W 470 1/16W 0 1/16W 0 1/16W 0 1/16W 0 1/16W 10k 1/16W 10k 1/16W 10k 1/16W 10k 1/16W 20k 1/16W 75 1/16W 0 1/16W 1.8k 1/16W 6.8 1/16W 6.8 1/16W 6.8 1/16W 910 1/16W 2.15k1/16W 0 1/16W ★ Part No. Description J 0 J 1k J 39 1/16W 1/16W 1/10W Chip 1608 Chip 1608 Chip 2125 Code AB AA AA SWITCH Chip 1608 AA Chip 1608 AA Chip 2125 AB Chip 1608 AA Chip 2125 AB Chip 1608 AA Chip 2125 AB Chip 1608 AA Chip 1608 AB Chip 1608 AB Resistor Array AD Resistor Array AD Chip 2125 AA Chip 3216 AB Chip 3216 AA Chip 3216 AA Chip 1608 AB Chip 1608 AA Chip 1608 AA Chip 1608 AA Chip 1608 AA Ceramic AB Ceramic AB Ceramic AB Ceramic AB Chip 1608 AA Ceramic AB Ceramic AB Ceramic AB Chip 1608 AB Chip 1608 AA Chip 1608 AA Chip 1608 AB Chip 1608 AB Chip 1608 AA Chip 1608 AB Chip 3216 AB Chip 1608 AA Chip 1608 AB Resistor ArrayAD Chip 1608 AB Chip 1608 AB Chip 1608 AA Chip 1608 AB Chip 1608 AB Chip 1608 AB Chip 1608 AB Chip 1608 AB Resistor ArrayAD Chip 1608 AA Chip 1608 AA Chip 1608 AB Chip 1608 AA Chip 1608 AB Chip 1608 AB Chip 1608 AB Chip 1608 AB Chip 1608 AA Chip 1608 AA Chip 1608 AA Chip 1608 AA Chip 1608 AA Chip 1608 AA Chip 1608 AB Chip 1608 AA Chip 1608 AB Chip 1608 AB Chip 1608 AB Chip 1608 AB Chip 1608 AB Chip 1608 AB SW80019DK001-70012 J SSSS811101 AL MISCELLANEOUS PARTS SC8001 9DK001-60078 SC8002 9DK001-60078 9DK001-99055 9DK001-99056 PSLDMA008WJFW NSFTZA001WJFW 9DK001-99058 163 J J J J J J J 54230-0808 54230-0808 CPV-1.0-039039 CPV-1.0-013019 Shield Shaft EDS-0607M AQ AQ AQ AE AK AD AE XG-C50X CABINET AND MECHANICAL PARTS 2-2 6-1-2 6-1-4 2-5 H 6 2-4 2-9 2-7 6-1 6-2 6-1-5 2-1-4 2-6 2-3 6-1-1 2-1-6 2-1-1 A 6-1-3 6-3 2-8 6-1-6 1-1-5 1-1-2 1-1-4 2-1 1-1-3 2 2-1-3 7 G 40 1-3 7-1 2-1-5 1-2 2-1-2 2-1-5-2 2-1-5-3 36 2-1-2 2-1-5-4 7-2 41 E 1-1 37 1-1-1 44 2-1-5-1 H U 33 37 37 B 21 2-1-7 37 U F 1 J 52 F 37 50 I 32 B 39 22 24 19 G 45 A F K D 15 N 43 L 23 38 11 42 M C 27 30 C 28 49 39 48 Q E 39 10 46 29 37 12 15 47 E 3-18 D Q S 55 J G P 26 3-22 13 S D 39 4-4 N 4-3 3-21 L 4-2 5 17 8 3-27 4-1 3-12 14 3-30 3-11 3-14 I C 3-12 3-25 38 P 3-15 3-1-8 40 3-1-5 4 20 3-23 3-1-7 3-4 31 3-27 J 3-16 16 S 18 3-13 3-1-4 9 3-1-6 3-17 3-1-1 B T 3-2 40 3-2-1 3 3-1-3 3-25 3-1 3-19 3-27 35 3-29 3-7 3-8 3-3 3-9 3-10 K 3-6 A 3-5 3-5 3-28 3-2-2 3-1-2 51 M 3-24 34 T 25 1 2 3 4 164 5 6 XG-C50X Ref. No. Part No. ★ Description Code Ref. No. CABINET AND MECHANICAL PARTS 1 1-1 1-1-1 1-1-2 1-1-3 1-1-4 1-1-5 1-2 1-3 2 2-1 2-1-1 2-1-2 2-1-3 2-1-4 2-2 2-2-1 2-2-2 2-2-3 2-2-4 2-3 2-4 2-5 2-6 2-7 2-8 2-9 2-10 3 3-1 3-1-1 3-1-2 3-1-3 3-1-4 3-1-5 3-1-6 3-1-7 3-1-8 3-2 3-2-1 3-2-2 3-3 3-4 3-5 3-6 3-7 3-8 3-9 3-10 3-11 3-12 3-13 3-14 3-15 3-16 3-17 3-18 3-19 3-20 3-21 3-22 3-23 3-24 3-25 3-26 3-27 3-28 Not Available DBDYRA001WJ01 Not Available HiNDPA084WJSA HiNDPA085WJZZ HiNDPA088WJZZ PSPAKA008WJ00 LX-HZ3106CEFD LX-NZ3173CEFW Not Available – J – J J J J J J HDECQA025WJKA HDECQA026WJKA HDECQA027WJKA JBTN-A014WJKA LANGKA006WJFW MSPRCA001WJFW – J – J – J J – J J J J J J PSPAT0013CEZZ QCNW-A492WJZZ XBPSF26P06000 XEBSD30P08000 XEPSD26P08000 J J J J J Not Available – J – J J J – DBDYTA002WJ01 Not Available GCOVAA032WJKA Not Available HiNDPA057WJSA DBTN-A013WJ01 Not Available DBDYUA003WJ01 Not Available HiNDPA089WJSA HiNDPA090WJSA HiNDPA114WJSB Not Available LX-NZ3120CEFW LX-NZ3122CEFW PFiLDA003WJZZ DCOVAA029WJ01 J J J J Not Available – HPNC-A002WJSA J GCOVA1824CESA J GCOVAA030WJKA J GCOVAA038WJKA J GLEGPA003WJKA J GLEGPA004WJKA J GLEGPA005WJKA J HPNC-A001WJSA J JHNDAA001WJKA J LANGKA040WJFW J LX-HZ3105CEFD J LX-NZ3095CEFD J LX-NZ3123CEFE J LX-NZ3173CEFW J LX-NZA003WJFW J PFiLDA002WJZZ J PSLDMA074WJZZ J PSPAH0648CE00 J PSPAT0013CEZZ J PZETKA013WJZZ J PZETKA014WJZZ J PZETKA015WJZZ J QCNW-A493WJZZ J XBPSD30P08JS0 J XBPSD40P05J00 J XEBSD30P12000 J XEPSD26P08000 J Rear Body Unit Ass'y Rear Body Ass'y Rear Body Terminal Indication Panel Earth Label Lamp Replacement Label Spacer, x2 Screw, x1 Insert Nut, x1 — AZ — AH AD AE AD AB AD Top Body Unit Ass'y Top Body Ass'y Top Body LED Cover "SHARP" Badge "IQ" Label Operation Button Ass'y Operation Button LED Cover LED Cover LED Cover Height Adjust Button Fixing Angle Spring, for Height Adjust Button Tape, x4 Leaf Switch Screw, x1 Screw, x1 Screw, x1 — BE — BB — AF AX — AH AH AH AE AD AB Bottom Body Unit Ass'y Bottom Body Ass'y Bottom Body Model Label FCC Label Hot Caution Label Kensington Standard Security Connector Insert Nut(R) Insert Nut(L) PBS Filter Bottom Filter Cover Ass'y Bottom Filter Cover Intake Punching Cover R/C Cover Exhaust Panel Handle Cover, x2 Adjuster Foot(Front) Adjuster Foot(Rear, Right) Adjuster Foot(Rear, Left) Punching Cover Carrying Handle Anti-Theft Angle Screw, for Insert Nut, x1 Nut Screw(R) Nut Screw(L) Insert Nut, x1 Nut, x3 Filter Shield Spacer, x2 Tape, x1 Shield Spacer, x1 Shield Spacer, x1 Shield Spacer, x1 Leaf Switch Screw, x8 Screw, x3 Screw, x7 Screw, x1 — BE — AN AL AD — AC AH AA AA AA AB AC AG AR — AL AD AM AF AW AH AH AL BH AD AB AA AD AD AD AE AK AB AC AG AH AD AF AA AA AA AA 165 Part No. ★ Description 3-29 3-30 3-31 LANGKA075WJFW J Angle XJPSF30P08000 J Screw, x1 PGiDJA001WJKZ J Spacer 4 4-1 4-2 4-3 4-4 DBFL-A001WJ01 QCNW-5062CEZZ VSP7040PB568A XEBSD30P08000 5 Refer to Optical Mechanism parts 6 6-1 6-1-1 6-1-2 6-1-3 6-1-4 6-1-5 6-1-6 6-2 6-3 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 49 50 51 51 51 52 53 Not Available Not Available – J J J J Code Speaker Net Ass'y Speaker Net Ass'y Connection Cord(SP) Speaker Screw, x4 AG AA — AE AL AA HiNDPA086WJZZ HiNDPA087WJZZ PSPAHA070WJ00 PSPAHA071WJ00 PSPAHA072WJ00 LX-BZ3366CEFN XRESJ30-06000 – J – J J J J J J J Lamp Door Unit Ass'y Lamp Door Ass'y Lamp Door Caution Label Caution Label Spacer Spacer Spacer Screw, x1 E-ring, x1 — AQ — AF AE AB AB AA AD AA CCOVAA027WJKA GCOVAA028WJKA HPNC-A003WJFW LANGTA007WJFW LHLDW1003GEZZ LHLDW1060CEZZ LHLDZA009WJKZ LX-BZA020WJZZ LX-HZA007WJFD NFANRA004WJZZ PCAPFA003WJSA PSPAGA036WJZZ PZETKA004WJZZ PZETKA005WJ00 PZETZA004WJKZ DUNTKB170DE01 DUNTKB171FE01 DUNTKB172DE01 DUNTKB173DE01 RUNTKA021WJZZ CPCi-A002CE01 RDENCA011WJZZ RDENCA012WJZZ QCNW-A491WJZZ QCNW-A774WJZZ QCNW-A496WJZZ QCNW-A899WJZZ QCNW-A495WJZZ XBBSD40P12000 XBBSF30P10000 XBPSD30P06R00 XEBSD30P08000 XEBSD30P12000 XEBSF30P12000 NSFTZ0134CEFW NSFTZA001WJFW GCOVHA014WJKZ LANGTA005WJFW LANGTA006WJFW PSLDMA008WJFW LHLDW1021GE00 PSPAZA061WJZZ PSLDMA009WJFW TLABNA053WJZZ TLABNA110WJZZ TLABNA111WJZZ 95KECB8034ZZ 95KEDB7717ZZ J J J J J J J J J J J J J J J – – – – – J – J J J J J J J J J J J J J J J J J J J J J J J J J J Lens Cover(Upper) Ass’y Lens Cover(Lower) Cooling Fan Attaching Angle AC Socket Attaching Angle Wire Holer, x1 Wire Holer, x1 PWB Holder Screw, x2 Screw, x4 Cooling Fan Lens Cap Fan Spacer, x6 Shield, for Ballast Unit Shield, for Output Unit Insulating Sheet Input Unit Output Unit Key Unit R/C Receiver Unit AC Inlet Unit PC I/F Unit Power Unit Ballast Unit Bi-Metal Connecting Cord(FG) Connecting Cord Connecting Cord Connecting Cord Screw, x1 Screw, x4 Screw, x16 Screw, x4 Screw, x13 Screw, x10 Shaft Screw, x6 Shaft Screw, x4 Shading Cover Attaching Angle, x2 Attaching Angle, x1 Shield Wire Holder, x1 Spacer, x2 Terminal Shield Serial No. Label(XG-C50XU) Serial No. Label(XG-C50XE) Serial No. Label(XG-C50XK) Connecting Cord Connecting Cord AR AH AP AD AA AB BB DDORRA001WJ01 Not Available AB AR AG AD AQ AP AD — — — — — CW — CB AM AD AG AD AD AB AA AB AA AA AA AD AD AD AE AG AK AC AD AH AC AE AG XG-C50X OPTICS MECHANISM PARTS-1/2 H 5-2 5-2-7 5-2-6 5-2-6 5-2-7 5-2-6 5-2-1 5-2-6 G 5-2-5 5-2-2 5-2-7 A 5-2-3 5-2-6 5-1 5-2-4 5-1-15 5-1-16 5-2-2 5-2-1 5-2-7 5-2-7 F 5-1-4 5-1-1 5-1-2 5-1-12 5-1-14 5-3 5-1-11 5-3-1-14 5-3-1-10 E 5-3-1-1 5-3-1-1 5-3-1-11 5-3-1-14 5-3-1-1 5-3-1-13 5-3-1-5 5-3-1-13 5-3-1-5 5-3-1-14 5-1-8 5-3-4 5-3-1-2 5-3-1-6 5-1-9 5-3-1-12 5-1-9 5-3-1-5 D 5-3-1-8 5-1-6 5-3-10 5-3-1-4 5-1-9 5-1-9 5-3-1-13 5-1-5 5-3-1-7 5-3-1-3 C 5-1-9 5-3-2 5-1-10 5-3-3 5-1-9 5-5 5-3-5 5-1-5 5-1-10 5-1-9 5-31 5-1-10 5-1-9 B 5-3-1-14 5-1-7 5-1-13 5-1-6 A 1 2 3 4 166 5 6 5-1-13 XG-C50X OPTICS MECHANISM PARTS-2/2 H 5-4 5-4-6 5-4-9 5-4-2 5-4-8 5-4-1 5-4-1-4 5-4-6 5-45 G 5-4-1-1 5-4-10 5-4-9 5-4-3 5-4-1-1 5-4-4 5-9 5-4-1-3 5-4-7 5-4-1-2 5-4-1-4 5-45 A 5-11 5-45 5-45 5-46 F 5-6 5-45 5-11 5-45 5-16 5-43 5-12 5-34 5-36 5-36 5-12 5-45 5-45 5-8 5-35 E 5-10 5-11 5-21 5-22 5-23 5-40 5-31 5-42 D 5-21 5-25 5-24 5-33 5-14 5-32 5-39 5-41 5-29 5-21 5-39 5-30 5-38 5-46 5-17 C 5-20 5-46 5-18 5-7 5-28 5-24 B 5-37 5-12 5-12 5-37 5-46 5-13 5-39 A 5-15 5-45 1 2 3 5-45 4 167 5 6 XG-C50X Ref. No. Part No. ★ Description Code Ref. No. 5-15 5-16 5-17 5-18 5-19 5-20 5-21 5-22 5-23 5-24 5-25 5-26 5-27 5-28 5-29 5-30 5-31 5-32 5-33 5-34 5-35 5-36 5-37 5-38 5-39 5-40 5-41 5-42 5-43 5-44 5-45 5-46 OPTICAL MECHANISM PARTS 5 CCHSKA001WJ01 5-1 Not Available 5-1-1 LANGKA009WJFW 5-1-2 LHLDW1037CEZZ 5-1-3 LHLDW1182CEZZ 5-1-4 NFANRA005WJZZ 5-1-5 NFANSA002WJZZ 5-1-6 NFANSA003WJZZ 5-1-7 PDUC-A001WJKZ 5-1-8 PDUC-A002WJKZ 5-1-9 PSPAZ0373CEZZ 5-1-10 PSPAZA017WJZZ 5-1-11 QCNW-A498WJZZ 5-1-12 QCNW-A499WJZZ 5-1-13 RH-HXA002WJZZ 5-1-14 RUNTKA026WJZZ 5-1-15 XBPSD26P14000 5-1-16 XEBSD30P12000 5-2 Not Available 5-2-1 LANGKA004WJFW 5-2-2 LANGKA005WJFW 5-2-3 NFANRA003WJZZ 5-2-4 PDUC-A003WJKZ 5-2-5 PSLDPA003WJFW 5-2-6 PSPAZ0373CEZZ 5-2-7 XEBSD30P12000 Not Available 5-3 5-3-1 CMiR-A004WJ01 5-3-1-1 LANGKA001WJFW 5-3-1-2 LANGKA002WJFW 5-3-1-3 LANGKA003WJFW 5-3-1-4 LANGKA036WJ00 5-3-1-5 LANGUA001WJFW 5-3-1-6 PFiLWA018WJZZ 5-3-1-7 PFiLWA019WJZZ 5-3-1-8 PFiLWA020WJZZ 5-3-1-9 Not Available 5-3-1-10 RLCDPA007WJZZ 5-3-1-11 RLCDPA008WJZZ 5-3-1-12 RLCDPA009WJZZ 5-3-1-13 XASSF26P07000 5-3-1-14 XiPSF20P04000 5-3-2 LHLDZA002WJFW 5-3-3 LHLDZA036WJFW 5-3-4 LX-BZ3248CEFF 5-3-5 XBPSF30P08JS0 5-4 BQC-XGC50X//1 5-4-1 Not Available 5-4-2 LX-BZ3449CEFN 5-4-3 PCASZA002WJKZ 5-4-4 PSLDHA001WJFW 5-4-5 XREUW20-04000 5-4-6 LANGKA072WJFW 5-4-7 LANGUA002WJFW 5-4-8 MSPRKA002WJFW 5-4-9 PSLDHA011WJFW 5-4-10 RLMPFA003WJZZ 5-4-11 TLABZA053WJZZ 5-4-12 XBPBN30P06JS0 5-4-13 XBPSF30P08JS0 5-4-14 XEBSD30P12000 5-5 GCOVUA003WJKZ 5-6 LANGKA037WJFW 5-7 LCHSKA001WJKZ 5-8 LCHSKA002WJKZ 5-9 LHLDW1046CEZZ 5-10 LHLDW1076GEZZ 5-11 LHLDZA001WJKZ 5-12 MSPRP1198CEFW 5-13 NFANSA002WJZZ 5-14 NFANSA003WJZZ J – J J J J J J J J J J J J J J J J – J J J J J J J – J J J J J J J J J – – – – J J J J J J J – J J J J J J J J J J J J J J J J J J J J J J J Optical Mechanism Unit Intake Duct Ass'y IC Fan Angle Wire Holder, x1 Cable Clamp, x1 Cooling Fan, x1 Blow Fan, x2 Blow Fan, x1 Intake Duct(Bottom) Intake Duct(Top) Spacer, for Fan, x12 Spacer, for Fan, x3 Connecting Cord(SO) Connecting Cord(EB) Thermister Fan Unit Screw, x2 Screw, x2 Exhaust Duct Ass'y Fixing Angle, x2 Fixing Angle, x2 Exhaust Fan Exhaust Duct Heat Sink Spacer, for Fan, x8 Screw, x5 Prism Holder Unit Prism Unit Fixing Spring, x3 Fixing Angle(Upper) Fixing Angle(Lower) Light Shielding Angle LCD Attaching Angle, x3 Output Polarizer(G) Output Polarizer(B) Output Polarizer(R) Cross Dichroic Prism R-LCD Panel G-LCD Panel B-LCD Panel Screw, x9 Screw, x10 Prism Holder Lens Mount Screw, x4 Screw, x4 Lamp Unit Lamp Case Ass'y Screw, x2 Lamp Case Heat Sink E-ring, x2 Fixing Angle Lamp Adjusting Angle Reflector Fixing Angle Heat Sink Lamp Caution Label Screw, x2 Screw, x6 Screw, x1 Light Shield Plate Temp. Sensor Attaching Angle Optical Mecha. Unit, Base Optical Mecha. Unit, Cover Wire Holder Cable Clamp Holder, x3 Mirror Adj. Holder, x3 Mirror Fixing Spring, x6 Blow Fan Blow Fan FX — AH AA AC AR AV AU AN AM AC AB AF AH AH BD AA AA — AD AD AV AQ AC AA — AD AE AE AK AH BF BG BG — — — — AC AA AZ BD AB AA CQ — AC AR AE AA AD AN AD AE CL AC AB AA AA AD AD AY AV AA AA AD AD AV AU 168 Part No. PCOVZA001WJKZ PCOVZA002WJKZ PFiLWA021WJZZ PFiLWA022WJZZ PFiLWA023WJZZ PFiLWA024WJZZ PLNS-A006WJZZ PLNS-A007WJZZ PLNS-A008WJZZ PLNS-A009WJZZ PLNS-A010WJZZ PLNS-A011WJZZ PLNS-A012WJSA PLNS-A015WJZZ PMiR-0219CEZZ PMiR-A005WJZZ PMiR-A006WJZZ PMiR-A008WJZZ PMiR-A009WJZZ PSLDHA003WJFW PSLDHA004WJFW PSPAT0076CEZZ PSPAZ0373CEZZ PSPAZA013WJZZ PSPAZA014WJZZ PSPAZA016WJZZ PSPAZA017WJZZ PSPAZA090WJZZ QCNW-A546WJZZ RH-HXA003WJZZ XBPSF30P08JS0 XEBSD30P12000 ★ J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J J Description PBS Fan Holder Lamp House Incoming PF(G) Incoming PF(B) Incoming PF(R) UV Absorbing Filter Fly-eye Lens-1 Fly-eye Lens-2 Condenser Lens-1 Condenser Lens-2, x2 Relay Lens-1 Relay Lens-2 Projection Lens Relay Lens-3 Reflection Mirror(M3) Reflection Mirror(M1) Reflection Mirror(M2) Reflection Mirror(M4) Reflection Mirror(M5) Heat Sink, for Lamp House Heat Sink, for Lamp House Teflon Tape, x2 Fan Spacer, x2 Mirror Spacer, x10 Blow Fan Spacer, x3 Fixing Spacer, x13 Fan Spacer, x2 Glass Tape, x1 Connecting Cord Temp. Sensor Screw, x22 Screw, x4 Code AH AS BB BG BD AU BE BS AX AS AT AQ BZ AS AS AZ AV AM AL AF AF AC AC AB AD AB AB AF AG AH AA AA XG-C50X Ref. No. Part No. ★ Description Code Ref. No. å å J J J J å QACCDA012WJPZ J å QACCL3022CEZZ J å QACCV4002CEZZ J QCNWGA012WJPZ QCNWGA013WJPZ QCNWGA014WJPZ QCNWGA015WJPZ RCORF0083CEZZ J J J J J RRMCGA029WJSA TCADEA009WJZZ TCAUZA015WJZZ TGAN-A018WJZZ TGAN-A019WJZZ TGAN-A020WJZZ TGAN-A027WJZZ TiNS-A139WJZZ TiNS-A163WJZZ UDSKAA005WJN1 UDSKAA007WJZZ J J J J J J J J J J J Dust Cover Extra Air Filter Power Cord(XG-C50XK) Power Cord (for U.S., Canada, etc) Power Cord(for U.K., Hong Kong Singapore) Power Cord(for Australia, New Zealand and Oceania) Power Cord (for Europe, except U.K.) RGB Cable Computer Audio Cable USB Cable DIN-D-sub RS-232C Adaptor Core, for Power Cord (XG-C50XU) Remote Control Questionnaire Card Stipulation Card Guarantee Card(XG-C50XU) Guarantee Card(XG-C50XU) Guarantee Card(XG-C50XU) Guarantee Card(XG-C50XU) Operation Manual Operation Manual CD-ROM(SAPS) CD-ROM(INS) ★ Description Code PACKING PARTS SUPPLIED ACCESSORIES GCOVDA001WJZZ PFiLDA005WJZZ QACCB5024CENA QACCDA010WJPZ Part No. (NOT REPLACEMENT ITEM) AL AF AZ AR SPAKCA231WJZZ SPAKFA040WJZZ SPAKFA071WJZZ SPAKP0805CEZZ SPAKXA053WJZZ SSAKA0160CEZZ TLABK0001TAZZ AR – – – – – – – Packing Case — Packing Case, for Accessories — Partition — Polystylene Cover — Buffer Material — Polyethylene Bag — No. Label — AZ AZ AS AK AQ AK AL BB AG AE AF AF AF AF AK AQ AM AM EXTENSION CABLE (Use for servicing) QCNW-A537WJZZ QCNW-A538WJZZ QCNW-5688CEZZ 169 J Connecting Cable (OUTPUT-PC I/F) J Connecting Cable (OUTPUT-INPUT) J Connecting Cable (OUTPUT-LCD), x3 BK XG-C50X PACKING OF THE SET/VERPACKEN DES GERÄTS Remote Control "AA" size Battery (2pcs) Power Cord RGB Cable USB Cable Computer Audio Cable DIN-D-sub RS-232C Adaptor Extra Air Filter Dust Cover CD-ROM (SAPS) CD-ROM (INS) Operation Manual Quick Reference Label Remote Control Packing Case, for Accessories Buffer Material Polystyrene Cover Lens Cap Front Packing Case Fix with craft tape. No. Label Fix with 8 staples. 170 XG-C50X 171 XG-C50X COPYRIGHT © 2002 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher. D Japan P Japan TQ1392-S Sep. 2002 Printed in Japan In Japan gedruckt SY. KG SHARP CORPORATION AV Systems Group Quality & Reliability Control Center Yaita, Tochigi 329-2193, Japan
This document in other languages
- Deutsch: Sharp XG-C50X