Download - One Control
Transcript
Page 1 © LEP International Co, Ltd. One Control | Crocodile Tail Loop Thank you for your purchase of the Crocodile Tail Loop by One Control. The crocodile Tail Loop is the flagship switcher from One Control. Create up to 70 presets with the easy push button auto saving system. The OC10 has 7 programs per bank and you can choose up to 10 programs for each program. The OC10 also is equipped midi and can send program changes or to be used as a midi through to be used in combination with other midi devices. Link two OC10 together with a simple LAN cable to access multiple pedals off 1stage. The OC10 also has the amazing BJF buffer from One Control included and also can be Overview bypassed by using the not buffered input. The OC10 can also be a simple switcher but accessing the direct mode. Perfect for band practices or experimenting with pedals before you’ve decided how to set your programs. The Crocodile Tail Loop truly is one of the most innovative pedal switchers on the market. Top Panel To get the full potential of the unit and to avoid misuse, please read this user guide carefully. 9 10 11 11 12 12 8 7 6 5 4 3 8 7 6 5 5 4 10 3 2 9 2 13 13 1 — PGM7/L7 These switches instantly recall the presets stored in the corresponding program (1 - 7) when pressed in 1 PGM1/L1 PGM mode. They directly turn loops 1 - 7 on or off when pressed in DIRECT mode. UP/L8 In PGM mode, this switch increases the bank, there are 10 banks available (1,2,3,4,5,6,7,8,9,0), in DIRECT mode, 2 BANK PGM1/L1 this switch turns (1) on/off loop 8. ~ PGM7/L7 These switches instantly recallthe thebank, presets stored in the corresponding mode, this switch decreases in DIRECT mode, this switch turns on/off loop 9. 3 BANK DN/L9 In PGM program (1 ~ 7) when pressed in PGM mode. They directly turn loops 1 ~ 7 CONFIG LINK config feature is active only in PGM mode, push the tact switch to config the mode, 4 LINK or off pressed in DIRECT mode. - SYNC mode, M/Son LEDs arewhen both off 5 6 5 - DOWNLOAD MASTER mode, M/S red LED is on. (2) BANK UP/L8 - DOWNLOAD SLAVE mode, M/S green led is on. Check LINK sectionInfor more detail.this switch increases the bank, there are 10 banks available PGM mode, (6) Program Buttonsis active only in PGM mode, push the tact switch to config the mode, MIDI ON/OFF MIDI config feature (1,2,3,4,5,6,7,8,9,0), in DIRECT mode, this switch turns on/off loop 8. - If TX is on, OC10INwill transmit program change through MIDI OUT jack. separately, the signal PGM mode these buttons turn on / off LOOP1 to LOOP10 - If RX is on, OC10sends willBANK listen thewhich program change (3) DN/L9 to theto loop is turned on ( command LED on). in through DIRECT MIDI modeIN thejack. buttons are disabled. Check MIDI section for more detail. mode,these this buttons switch decreases bank, in DIRECT mode, this switchsends to the loop which is Program Buttons In IN PGM PGM mode turn on / offthe LOOP1 to LOOP10 separately, the signal turns on/offmode loopthe 9. buttons are disabled. LED Display turned on ( LED(7) on). in DIRECT In PGM mode, LED shows thebank banknumber, number,ititshows shows ““ ”” in LED Display In PGM mode, thethe LED shows the in DIRECT DIRECT MODE. MODE. (4) LINK CONFIG 7 In PGM mode, thisfeature switch shuts off the OUT-1 and mode, OUT-2 and switches input to jack,mode, press it again will LINK config is active only in PGM push the tacttheswitch to TUNER config the 8 TUNER/L10 get back to normal operation. In DIRECT mode the switch turns on/off loop 10. (8) TUNER/L10 - SYNC mode, M/S LEDs are both off In -PGM mode, this switch shutsmode, off the OUT-1 andLED OUT-2 and switches the input DOWNLOAD MASTER M/S red is on. to -TUNER jack, press it againmode, will getM/S backgreen to normal DOWNLOAD SLAVE ledoperation. is on. In DIRECT mode Page 2 9 STATUS LED The LED only be active in DIRECT MODE, it turns on when loop 8 is engaged. 10 STATUS LED The LED only be active in DIRECT MODE, it turns on when loop 9 is engaged. 11 STATUS LED The LED shows TUNER ON/OFF status in PGM mode, in DIRECT mode it will turn on when loop 10 is engaged. LED In PGM mode it turns on when its corresponding program is recalled. In DIRECT mode it will turn on when its 12 STATUS corresponding loop is engaged. 13 GUARD BAR The guard bar protects the buttons and display panel, it is remove-able. Rear Panel 15 15 16 16 17 17 11 12 13 8 14 11 12 13 14 8 11 22 33 44 55 66 77 88 99 10 10 1 MIDI OUT/THRU The toggle switch setups the MIDI JACK for “OUTPUT” or “THRU” function. 2 3 4 5 6 (1) MIDI OUT/THRU LINK Connect the link cable here. The toggle switch setups the MIDI JACK for “OUTPUT” or “THRU” function. 9V IN Connect to an external 9V DC power source 5.5x2.1mm center negative. (2) LINK BUF IN Signal inputConnect via this jack fedcable to a buffer the islink here.circuit prior to being sent to the loops. BUF OUT The input (3) signal 9V INreceived at the BUF-IN jack is directly output via the BUF OUT jack prior to being send to loops. to an 9Vvia DCbuffered power source, 5.5x2.1mm, negative TUNER When OUTConnect are muted, theexternal input signal or non-buffered reaches this jack.center type. (4)switch BUF setups IN the MIDI JACK for “OUTPUT” or “THRU” function. 7 INPUT The toggle Signaljacks inputforviaseries this jack fed to a7), buffer circuit prior being sent to the loops. and OUT2 Output loopsis(LOOP1the input signal viatobuffered or non-buffered Input jacks reaches the 8 OUT1 two jacks via the 7 series loops, OUT-1 and OUT-2 jacks are Internally connected in parallel. 9 10 11 12 13 14 15 16 17 (5) BUF OUT SEND 1–7 Send jacks of LOOP1–7, connect to input jack of guitar pedals. The input signal received at the BUF-IN jack is directly output via the BUF OUT jack RETURN 1–7 Return jacks of LOOP1–7, prior to being send toconnect loops. to output jack of guitar pedals. IN8 - IN9 - IN10(6) Input of separate LOOP8–10. prior to sending to loops. TUNER When OUT are muted, the input signal via or non-bufferd reaches this jack S8 - S9 - S10 SEND jack of separate LOOP8, LOOP9,LOOP10, thebuffered jacks should be connected to the input of guitar pedals. These jacks also function as latching N.C (Normally Closed) switch which works as foot-switch to control amplifier channel. The sleeve and tip of the jack “closed”/“open” when the loop is “off/on”. (7)are INPUT R8 - R9 - R10 Return of separate LOOP8,the LOOP9,LOOP10, the“OUTPUT” jacks shouldorbe connected to the output of Thejack toggle switch setups MIDI JACK for “THRU” function. guitar pedals. (8) OUT1 andjack OUT2 OUT8 - OUT9 - OUT10 Output of separate LOOP8, LOOP9, LOOP10, the jacks also function as latching N.O (Normally Open) switches which work as foot-switch to control amplifier channel. tip of jack areor “open”/“closed” Output jacks for series loops (LOOP1 ~ 7),The thesleeve input and signal viathe buffered non-bufferd when the loop is off/on. jacks reaches the two jacks viathe theMIDI 7 series OUT-1 and OUT-2 are MIDI IN Receives Input MIDI data from an external MIDI device, IN is loops, not available in when it is set jacks as DOWNLOAD SLAVE device. Check detail in MIDI and LINK sections. Internally connected in parallel. MIDI OUT/THRU Transmits MIDI data to an external MIDI device. (9) SEND 1~7 GROUND STUB Connect the stub to earth to ground the frame. Send jacks of LOOP1~7, connect to input jack of guitar pedals. (10) RETURN 1~7 Return jacks of LOOP1~7, connect to output jack of guitar pedals. (11) IN8,IN9,IN10 Input of separate LOOP8~10. prior to sending to loops. Page 3 2- Signal Path Signal Path LOOP1 NBUF IN LOOP2 LOOP4 LOOP5 LOOP6 LOOP7 LOOP8 LOUT1 LOUT2 TUNER BUF IN BUF OUT IN8 LOOP3 OUT8 IN9 LOOP9 OUT9 IN10 LOOP10 OUT10 Guitar signal feedsGuitar into OC10 input IN or BUF IN), enters series LOOP1~LOOP7 when MUTE switch is off, feeds(NBUF into OC10 input (NBUF INpushed, or BUF IN), then outputs from OUT-1signal and OUT-2. when TUNER switch is the enters signal series outputs to TUNER jack. Be noted when MUTE switch is off, outputs from OUT-1 and OUT-2. the BUF OUT jackLOOP1~LOOP7 doesn’t output when the guitar plug intothen NBUF IN jack. when TUNER switch is pushed, the signal outputs to TUNER jack. Recall Programs Be noted the BUF OUT jack output when guitar plug into NBUF is IN active. jack. Recall / Press preset switches to recall presets, the doesn’t corresponding LED the lights up when a preset bypass operation will not change the MUTE status. 3- Recall Programs TUNER Press preset switches to TUNER recall presettings, corresponding Press TUNER/L10 switch the guitar signal to jack and mute the the output (OUT-1 and OUT-2) at the same time. Press the switch again will switch back the guitar signal to loops. LED lights on when a preset is active. TUNER function works individually, recalling programs do not affect TUNER function. Recall / bypass operation will not change the MUTE status. Bank UP/DOWN Oc10 have 10 banks from 1 to 10(”0"), each bank store 7 programs. Press BANK UP or BANK DOWN switches to change the bank, the numerical bank display blinks when the bank is about to be changed. Press any 4- TUNER PGM switch to recall new bank programs. Press TUNER/L10 switch the guitar signal to TUNER jack and mute Programming thethe loops output (OUT-1 and OUT-2) at the same time. Press the switch Press the program buttons to turn on/off corresponding loops, the loop status LED will be on/off accordingly, again will switch the memory automatically stores the back statusthe of allguitar loops. signal to loops. TUNER function works individually, recalling programs do not affect PGM/ DIRECT MODE TUNER function. Oc10 is able to work in DIRECT mode, holding the TUNER/L10 switch for 3 seconds will turn on DIRECT mode, the numerical display shows “-”. In DIRECT mode each stomp switch (L1 ~ L10) turns on/off the loop1~loop10 separately. holding the TUNER/L10 switch for 3 seconds will turn off DIRECT mode and back to PGM mode. 5- Bank UP/DOWN Note: in DIRECT mode the MIDI and LINK function are not available. Oc10 have 10 banks from 1 to 10(”0"), each bank store 7 programs. Configurate MIDI BANK UP the or BANK DOWNPress switches to change the to bank, A program allows Press to enable/disable MIDI functions. MIDI ON/OFF button turn on/off the transmit (TX) and receive(RX) MIDI, TX/RX led’sdisplay show the on/offwhen status. The TX/RX status to is stored into a PGM theofnumerical bank blinks the bank is about be automatically. When the TX is on, a PGM recall will transmit a “MIDI program change” command via MIDI OUT changed. Press any PGM switch to recall new bank programs. jack on MIDI channel 0. The program change number is from 0 to 69, the number of Bank 1/PGM 1 is 0, the number of BANK 10/PGM7 is 69. When the RX is on, a “MIDI program change” on MIDI channel 0, from an external MIDI device will recall the corresponding PGM of Oc10. if program change number is 0, it recalls BANK 6- Programming the loops 1/PGM1 on Oc10. LINK FUNCTIONPress the program buttons to turn on/off corresponding loops, the status LED on/off accordingly, memory Oc10 allows to link toloop another Oc10 and will workbe together. There’re 2 link the modes, SYNC and DOWNLOAD mode. In SYNC mode, a PGM recall will cause the same PGM recall on another unit, for example, recall BANK 1/ PGM7 automatically stores the status of all loops. on Oc10 A, the BANK1/PGM7 on Oc10 B will be recalled simultaneously, if press PGM7 of BANK 2 on Oc10 B, the BANK2/PGM7 on Oc10 A will be recalled at the same time. In DOWNLOAD mode, the MASTER Oc10 downloads the data to the SLAVE Oc10. The SLAVE Oc10 duplicates the MASTER Oc10. Push the LINK CONFIG button changes the LINK mode. The mode is SYNC when M/S led is off. The mode is DOWNLOAD MASTER when M/S led is red. The mode is DOWNLOAD SLAVE when M/S led is green. The blue LINK led lights on when two Oc10 are connected with LINK cable. Note: The MIDI IN is not available when Oc10 is set as DOWNLOAD SLAVE device Page 4 Specifications POWER SUPPLY: DC9V CURRENT DRAIN: max. 450mA INPUT IMPEDANCE: 500K Ohm OUTPUT IMPEDANCE: 10K Ohm MAX. BUFFERED INPUT: 9V MAX NON_BUFFERED OUTPUT: 30V DIMENSIONS: 462x110x64 mm — 18.2x4.35x2.5 Inch WEIGHT: 1800g — 4 lb. Warranty Repairs or exchanges under warranty are subject to these warranty guidelines: This product is covered under our warranty for the period of 1 year from date of purchase, as filled out on the warranty card. In the case the product needs to be shipped, the cost of shipping will be paid by the buyer. The Following are not covered by this warranty: Fire, earthquake, natural disasters such as flooding, material breakage, or war. Warranty is void if there is any trace of repair or modification that is not performed or authorized by LEP International. One Control by LEP International Co, LTD. 9-16 Suehiro Hanamaki Iwate 025-0079, Japan Phone: 0198-23-6600 Fax: 0198-29-4244 [email protected] www.one-control.com