Quick Start Setup Guide - Direct Video Entertainment Download

Transcript
Quick Start Setup Guide
46HFL5784L
42HFL5784D
42HFL5784L
39HFL5784D
39HFL5784L
46 42 39HFL5784D L
LC11_PHILIPS_hospitality_EN_QG.indd 1
2013/07/22 17:41:47
Know these
safety symbols
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of
uninsulated “dangerous voltage” within the apparatus’s enclosure
that may be of sufficient magnitude to constitute a risk of
electric shock to persons.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature accompanying
the apparatus.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The caution marking is located on the rear or bottom of the cabinet.
WARNING:
To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. Apparatus shall
not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the
apparatus.
CAUTION:
ATTENTION:
To prevent electric shock, match wide blade of plug to wide slot, fully insert.
Pour éviter les choc électriques,introduire la lame la plus large de la fiche dans la borne correspondante de la
prise et pousser jusqu’au fond.
Visit our World Wide Web Site at www.philips.com/support
www.philips.com/hospitality
CHILD SAFETY:
PROPER TELEVISION PLACEMENT MATTERS
WALL OR CEILING MOUNT YOUR
TELEVISION
™ALWAYSXdciVXindjggZiV^aZgVWdjiegd[Zhh^dcVa
^chiVaaVi^dc^[ndj]VkZVcnYdjWihVWdjindjgVW^a^inid
hV[ZanbdjcindjgiZaZk^h^dc#
™ALWAYSjhZVbdjcii]Vi]VhWZZcgZXdbbZcYZYWn
i]ZiZaZk^h^dcbVcj[VXijgZgVcY]VhVhV[ZinXZgi^[^XVi^dc
WnVc^cYZeZcYZciaVWdgVidgnhjX]VhJA!8H6!:IA#
™ALWAYS[daadlVaa^chigjXi^dchhjeea^ZYWni]Z
iZaZk^h^dcVcYbdjcibVcj[VXijgZgh#
™ALWAYSbV`ZhjgZi]Vii]ZlVaadgXZ^a^c\l]ZgZndj
VgZbdjci^c\i]ZiZaZk^h^dc^hVeegdeg^ViZ#HdbZbdjcih
VgZcdiYZh^\cZYidWZbdjciZYidlVaahVcYXZ^a^c\h
l^i]hiZZahijYhdgX^cYZgWadX`XdchigjXi^dc#>[ndjVgZ
jchjgZ!XdciVXiVegd[Zhh^dcVa^chiVaaZg#
™IZaZk^h^dchXVcWZ]ZVkn#6b^c^bjbd[ildeZdeaZ^h
gZfj^gZY[dgVlVaadgXZ^a^c\bdjci^chiVaaVi^dc#
MOVING AN OLDER TELEVISION TO A NEW
PLACE IN YOUR HOME
™BVcncZliZaZk^h^dcWjnZghbdkZi]Z^gdaYZg8GI
iZaZk^h^dch^cidVhZXdcYVgngddbV[iZgi]ZejgX]VhZd[V
[aVi"eVcZaiZaZk^h^dc#HeZX^VaXVgZh]djaYWZbVYZ^ci]Z
eaVXZbZcid[daYZg8GIiZaZk^h^dch#
™ALWAYSeaVXZndjgdaYZg8GIiZaZk^h^dcdc[jgc^ijgZ
i]Vi^hhijgYnVcYVeegdeg^ViZ[dg^ihh^oZVcYlZ^\]i#
™NEVEReaVXZndjgdaYZg8GIiZaZk^h^dcdcVYgZhhZg
l]ZgZX]^aYgZcbVnWZiZbeiZYidjhZi]ZYgVlZghid
Xa^bW#
™ALWAYSbV`ZhjgZndjgdaYZg8GIiZaZk^h^dcYdZh
cdi]Vc\dkZgi]ZZY\Zd[ndjg[jgc^ijgZ#
THE CONSUMER ELECTRONICS INDUSTRY
CARES
™BVcj[VXijgZgh!gZiV^aZghVcYi]ZgZhid[i]ZXdchjbZg
ZaZXigdc^Xh^cYjhignVgZXdbb^iiZYidbV`^c\]dbZ
ZciZgiV^cbZcihV[ZVcYZc_dnVWaZ#
™6hndjZc_dnndjgiZaZk^h^dc!eaZVhZcdiZi]ViVaa
iZaZk^h^dch¶cZlVcYdaY"bjhiWZhjeedgiZYdcegdeZg
hiVcYhdg^chiVaaZYVXXdgY^c\idi]ZbVcj[VXijgZg»h
gZXdbbZcYVi^dch#IZaZk^h^dchi]ViVgZ^cVeegdeg^ViZan
h^ijViZYdcYgZhhZgh!Wdd`XVhZh!h]ZakZh!YZh`h!heZV`Zgh!
X]Zhih!XVgih!ZiX#!bVn[VaadkZg!gZhjai^c\^c^c_jgn#
TUNE IN TO SAFETY
™ALWAYS[daadli]ZbVcj[VXijgZg»hgZXdbbZcYVi^dch
[dgi]ZhV[Z^chiVaaVi^dcd[ndjgiZaZk^h^dc#
™ALWAYSgZVYVcY[daadlVaa^chigjXi^dch[dgegdeZgjhZ
d[ndjgiZaZk^h^dc#
™NEVERVaadlX]^aYgZcidXa^bWdcdgeaVndci]Z
iZaZk^h^dcdgi]Z[jgc^ijgZdcl]^X]i]ZiZaZk^h^dc^h
eaVXZY#
™NEVEReaVXZi]ZiZaZk^h^dcdc[jgc^ijgZi]ViXVcZVh^an
WZjhZYVhhiZeh!hjX]VhVX]Zhid[YgVlZgh#
™ALWAYS^chiVaai]ZiZaZk^h^dcl]ZgZ^iXVccdiWZ
ejh]ZY!ejaaZYdkZgdg`cdX`ZYYdlc#
™ALWAYSgdjiZXdgYhVcYXVWaZhXdccZXiZYidi]Z
iZaZk^h^dchdi]Vii]ZnXVccdiWZig^eeZYdkZg!ejaaZYdg
\gVWWZY#
CE.org/safety
2
46 42 39HFL5784D L
LC11_PHILIPS_hospitality_EN_QG.indd 2
2013/07/22 17:41:48
Important Safety Instructions
1.
2.
3.
4.
5.
6.
7.
13. Unplug this apparatus during lightning storms or when
unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11. Only use attachments / accessories specified by the
manufacturer.
12. Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or
sold with the apparatus. When a cart
is used, use caution when moving the
cart / apparatus combination to avoid
injury from tip-over.
Note to the CATV system installer:
This reminder is provided to call the CATV system installer’s
attention to Article 820-40 of the NEC that provides guidelines for
proper grounding and, in particular, specifies that the cable ground
shall be connected to the grounding system of the building, as close
to the point of cable entry as practical.
Example of Antenna Grounding as per NEC - National
Electric Code
GROUND CLAMP
ANTENNA DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
ELECTRIC SERVICE EQUIPMENT
Wall Mount Bracket Kit
Brand
Model #
Screw dimension
PHILIPS
SQM6485
M6 x 1.614” (41mm)
with spacer
42HFL5784D
42HFL5784L
SANUS
39HFL5784D
39HFL5784L
SAN25BB
M4 x 0.472” (12mm)
46HFL5784L
•
•
•
•
ANTENNA LEAD IN WIRE
POWER SERVICE GROUNDING ELECTRODE
SYSTEM (NEC ART 250, PART H)
P&F USA is not liable for these types of accidents or
injury noted below.
• Install the Wall Mount Bracket on a sturdy vertical wall.
• If installed onto a ceiling or slanted wall, the TV and Wall
Mount Bracket may fall which could result in a severe injury.
• Do not use screws that are longer or shorter than their
specified length. If screws too long are used this may cause
mechanical or electrical damage inside the TV set. If screws
too short are used this may cause the TV set to fall.
• Do not fasten the screws by excessive force.This may
damage the product or cause the product to fall, leading
to an injury.
• For safety reasons use 2 people to mount the TV onto a
Wall Mounting Bracket.
• Do not mount the TV onto the Wall Mounting Bracket
while your TV is plugged in or turned on. It may result in
an electrical shock injury.
The recommended Wall Mount Bracket Kit (sold
separately) allows the mounting of the TV on the wall.
For detailed information on installing the wall mount,
refer to the Wall Mount Instruction Book.
P&F USA is not responsible for any damage to the
product or injury to yourself or others if you elect to
install the TV Wall Mount Bracket or mount the TV
onto the Bracket on your own.
The Wall Mount Bracket must be installed by experts.
When installing the unit on the wall, allow this much space.
Top:
Left and right side:
Bottom:
11.8 inches (30cm)
5.9 inches (15cm)
3.9 inches (10cm)
3
46 42 39HFL5784D L
LC11_PHILIPS_hospitality_EN_QG.indd 3
2013/07/22 17:41:48
1 Notice
Modifications
This apparatus may generate or use radio frequency energy. Changes
or modifications to this apparatus may cause harmful interference
unless the modifications are expressly approved in the manual. The
user could lose the authority to operate this apparatus if an
unauthorized change or modification is made.
Trademarks are the property of Koninklijke Philips Electronics N.V. or
their respective owners.
P&F USA reserves the right to change products at any time without
being obliged to adjust earlier supplies accordingly.
The material in this manual is believed adequate for the intended use
of the system. If the product or its individual modules or procedures
are used for purposes other than those specified herein, confirmation
of their validity and suitability must be obtained. P&F USA warrants
that the material itself does not infringe any United States patents. No
further warranty is expressed or implied.
P&F USA cannot be held responsible neither for any errors in the
content of this document nor for any problems as a result of the
content in this document. Errors reported to P&F USA will be
adapted and published on the P&F USA support website as soon as
possible.
Cables
Connections to this device must be made with shielded cables with
metallic RFI / EMI connector hoods to maintain compliance with FCC
Rules and Regulations.
Canadian notice
CAN ICES-3 (B)/NMB-3 (B)
Standard Television Receiving Apparatus, Canada BETS-7 / NTMR-7.
Copyright
All other registered and unregistered trademarks are the property of
their respective owners.
The terms HDMI and HDMI HighDefinition Multimedia Interface, and
the HDMI Logo are trademarks
or registered trademarks of HDMI
Licensing LLC in the United States and
other countries.
Pixel characteristics
This LCD product has a high number of color pixels. Although it has
effective pixels of 99.999% or more, black dots or bright points of light
(red, green or blue) may appear constantly on the screen. This is a
structural property of the display (within common industry standards)
and is not a malfunction.
Manufactured under license from Dolby
Laboratories. Dolby and the double-D
symbol are trademarks of Dolby
Laboratories.
Warranty
No components are user serviceable. Do not open or remove covers
to the inside of the product. Repairs may only be done by Service
Centers and official repair shops. Failure to do so shall void any
warranty, stated or implied.
Any operation expressly prohibited in this manual, any adjustments or
assembly procedures not recommended or authorized in this manual
shall void the warranty.
is a trademark of SRS Labs,
Inc. TruSurround HD technology is
incorporated under license from SRS
Labs, Inc.
SRS TruSurround HD™ creates an
immersive, feature-rich surround
sound experience from two speakers,
complete with rich bass, high frequency
detail and clear dialog.
Federal Communications Commission Notice
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the
receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio or television
technician for help.
Consumer Notice:
ENERGY STAR® is a joint program
of the U.S. Environmental Protection
Agency and the U.S. Department of
Energy helping us all save money and
protect the environment through
energy efficient products and practices.
This TV has been set to maximize energy efficiency while delivering
the best possible picture using the factory installed home mode
settings.
Changing or enabling other features in this TV (e.g. brightened
backlighting) will possibly increase energy consumption beyond the
original ENERGY STAR® qualified limits.
LED backlighting technology uses less
energy when compared with a standard
CCFL backlighting LCD television of the
same screen size. Actual energy savings
will vary depending on the screen size.
Declaration of Conformity
Portions of this software are copyright © The FreeType Project
(www.freetype.org).
Trade Name :
PHILIPS
Responsible Party : P&F USA, Inc.
Model :
46HFL5784L, 42HFL5784D, 42HFL5784L,
39HFL5784D, 39HFL5784L
Address :
PO Box 2248, Alpharetta, GA 30023 U.S.A.
Telephone Number : 1 866 497 4225
The American Academy of Pediatrics discourages television viewing
for children younger than two years of age.
4
46 42 39HFL5784D L
LC11_PHILIPS_hospitality_EN_QG.indd 4
2013/07/22 17:41:48
2 Important
CAUTION: Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
WARNING: Batteries (battery pack or battery installed) shall not
be exposed to excessive heat such as sunshine, fire
or the like.
Positioning the TV
•
•
•
•
•
•
•
•
•
•
•
•
WARNING: To prevent injury, this apparatus must be securely
attached to the furniture / wall in accordance with the
instructions. Tipping, shaking or rocking the unit may
cause injury / death.
Large screen TVs are heavy. 2 people are required to carry and
handle a large screen TV.
Make sure to hold the upper and bottom frames of the unit
firmly as illustrated.
Install the unit in a horizontal and stable
position.
Do not install the unit in direct sunlight
or in a place subject to dust or strong
vibration.
Depending on the environment, the
temperature of this unit may increase
slightly. This is not a malfunction.
Avoid a place with drastic temperature changes.
Do not place anything directly on top or bottom of the unit.
Depending on your external devices, noise or disturbance of
the picture and / or sound may be generated if the unit is placed
too close to them. In this case, please ensure enough space
between the external devices and the unit.
Do not insert the AC power cord into the power socket outlet
before all the connections are made.
Ensure that you always have easy access to the AC power cord
or plug to disconnect the TV from the power.
Before you move the TV, disconnect attached cables to prevent
damage to connectors.
Be sure to unplug the AC power cord from the AC outlet
before moving or carrying the unit.
Environmental care
The packaging of this product is intended to be recycled.
Contact your local authorities for information about how to recycle
the packaging.
For product recycling information, please visit www.recycle.philips.com
End of life directives
Philips pays a lot of attention to produce environment-friendly
products in green focal areas.Your new TV contains materials
which can be recycled and reused. At the end of its life, specialized
companies can dismantle the discarded TV to concentrate the
reusable materials and to minimize the amount of materials to be
disposed of. Please ensure you dispose of your old TV according to
local regulations.
Regulatory notices
Do not place the unit on the furniture that is capable of being tilted
by a child and an adult leaning, pulling, standing or climbing on it. A
falling unit can cause serious injury or even death.
This apparatus should not be placed in a built-in installation such as
a bookcase or rack unless proper ventilation is provided.
Make sure to leave a space of 4 inches (10cm) or more around this
apparatus.
Disposal of used batteries
The batteries supplied do not contain the heavy metals mercury
and cadmium. Nevertheless, in many areas batteries may not be
disposed of with your household waste. Please ensure you dispose
of batteries according to local regulations.
Press to turn the unit on and go into standby mode.
To completely turn off the unit, you must unplug the AC power
cord.
Disconnect the AC plug to shut the unit off when trouble is found
or not in use. The AC plug shall remain readily available.
AC plug
Never use a gas duster on this TV.
The gas trapped inside of this unit may cause ignition and explosion.
5
46 42 39HFL5784D L
LC11_PHILIPS_hospitality_EN_QG.indd 5
2013/07/22 17:41:49
How to use this guide
TV Setup
The Quick Start Setup Guide helps you install the Philips
commercial television, as quickly as possible. It contains the
necessary information to install the TV and configure the
settings. Read and understand the instructions in the Quick
Start Setup Guide before you use your TV.
For detailed information on additional features, download
the user manual by selecting your TV model at
www.philips.com/hospitality.
The Quick Start Setup Guide contains the following
information:
• Contents of the box
• Configuration of channel and advanced settings
• Cloning of data
As part of striving to improve the TV performance
throughout the product life, some TV menus may differ from
the illustration on this document.
Philips Hospitality TVs have a USB cloning capability so you
only need to manually setup one TV - the “master TV”. Then
the complete setup configuration can be copied from the
master TV to a USB storage device which can then be used
to load the same setup configuration into all other TVs.
Step 1 is to setup the master TV as follows:
Accessing the setup menu
To access and adjust the setup functions, YOU MUST USE
A SPECIAL SETUP REMOTE CONTROL (not provided
with the TV) IN THE RC5 SETUP MODE. All the following
instructions assume the use of a setup remote control in
the RC5 Setup mode.
Note
• The optional setup remote control is not included in the box.
Contact your Philips authorized agent or dealer to purchase the
setup remote control. Setup remote control might differ from
the illustration.
The contents of the box
The box contains the following items:
• TV
• TV stand
• Quick Start Setup Guide (this document)
• Warranty sheet
• Remote control
• 2 x AAA, 1.5V batteries
• TV stand hardware
A
B
C
D
E
F
G
RESET/UPGRADE
GUIDE
RECALL/INFO
HOME
MENU
BACK/PP
Stand-to-TV screws
(x 3 for 42HFL5784D, 42HFL5784L, 39HFL5784D,
39HFL5784L)
(x 4 for 46HFL5784L)
• Stand -to-Stand neck screw
(x 4 for 46HFL5784L)
• Stand pin
(x 2 for 42HFL5784D, 42HFL5784L, 39HFL5784D,
39HFL5784L)
• Screw for Stand pin
(x 4 for 42HFL5784D, 42HFL5784L, 39HFL5784D,
39HFL5784L)
• TV security package
• Stand-to-TV security hex screws
(x 3 for 42HFL5784D, 42HFL5784L, 39HFL5784D,
39HFL5784L)
(x 4 for 46HFL5784L)
• Stand -to-Stand neck security hex screw
(x 4 for 46HFL5784L)
• Security bolt and cap (x 2)
• Washer (x 2)
• Security nut (x 2)
• Security double-sided tape (x 4)
OPTIONS
ALARM/CLOCK
SMART
TELETEXT
CC
•
MUTE
TV
VOL
P
ABC
DEF
GHI
JKL
MNO
PQRS
TUV
WXYZ
AV
RC5 GUEST
SLEEP
RC5 SETUP
RC6 GUEST
RC6 SETUP
HOSPITALITY
Note
• The items are available on selected models only.
• An optional security tool is required to tighten the security
screws and nuts. Please contact your Philips authorized agent or
distributor to purchase the tool.
6
46 42 39HFL5784D L
LC11_PHILIPS_hospitality_EN_QG.indd 6
2013/07/22 17:41:49
Channel installation
39HFL5784D, 39HFL5784L
• Press . POWER at the front of the TV or use the
This section describes how to install the TV channels
automatically.
1 Connect the RF signal to the TV.
2 Plug the power cord into the power outlet.
. (POWER) on the remote control.
4
5
Cable
3
Press RC5 SETUP to put the remote control into setup
mode, then press the HOME/MENU button to display
the setup menu. (Hereafter, HOME/MENU will be
simply referred to as MENU)
Select Setup Menu - Channels - Autoprogram; then
select Cable. (unless the installation is using only Antenna
signals - in which case you would select Antenna)
Turn the TV on.
46HFL5784L, 42HFL5784D, 42HFL5784L
• Press . (POWER) at the rear of the TV or use the
. (POWER) on the remote control.
7
46 42 39HFL5784D L
LC11_PHILIPS_hospitality_EN_QG.indd 7
2013/07/22 17:41:51
f
g
h
i
a
j
b
c
d
e
a DATA (RJ-12 SPI port)
b Digital audio output jack
c IP Control port
d Antenna Input jack
GAME port
PC Input jack
USB terminal
HDMI Input jack(s)
i Audio input jack for PC connection
j Audio Video Input jack
*e
f
g
h
* 46HFL5784L, 42HFL5784L, 39HFL5784L only.
8
46 42 39HFL5784D L
LC11_PHILIPS_hospitality_EN_QG.indd 8
2013/07/22 17:41:53
Installation
Install TV Channels
(Skip if the TV is in PPV mode)
1
Note
Press MENU on the setup remote control to display
the setup menu.
2 Select Channels.
3 Select Installation mode and the required installation
mode(Antenna, Cable).
4 If auto installation is required, select Auto program and
Start.
5 If manual installation is preferred, select Manual setup
and the correct parameters.
After the initial setup, the TV can be further configured,
to achieve the desired behavior. A summary of available
options is described in the following sections.
• As part of the initial TV setup, there is PC application to
support the installation. The application that can be downloaded
at www.philips.com/hospitality or contact Philips agent
representative, this tool is subject to availability.
In the 1st time (Virgin) installation, the following steps
should be followed:
Language
If Language other than English is required, select the desired
language.
1
2
3
Press MENU on the setup remote control to display
the setup menu.
Select Settings.
Select the preferred language.
Channel setting setup
This section describes how to change the channel settings.
The TV must be in FTG mode for the channel settings to
be available.
1 Press MENU on the setup remote control to display
the setup menu.
2 Select Channels.
3 Manual setup options: Channel, Input, Channel
Logo, Digital, RF Channel Number, MPEG Program
Number, Rings, Label and Mute.
4 Select the Current Ring.
TV system
If TV is part of a PPV (Pay Per View) system
1
2
3
4
Press MENU on the setup remote control to display
the setup menu.
Select System.
Select SPI.
Select the correct SPI mode ( 3v3 , 5V).
If the TV will be used in FTG (Free To Guest) mode
(Skip if the TV is in PPV mode)
1
2
3
4
5
6
Configuration menu
Press MENU on the setup remote control to display
the setup menu.
Select System.
Select Pro:Idiom Control.
Select Mode.
Select FTG.
Enter the correct pass-code.
This section describes how to change the TV general
performance settings. Switch On settings and Control
settings.
1 Press MENU on the setup remote control to display
the setup menu.
2
Press Î ï to select the desired mode, then press OK.
property information.
Hotel Info Defines
(Hotel name and Room ID)
Defines the parameters loaded when the TV is
Switch On switched On and the OSD behavior.
and OSD (Welcome Message, Switch On Program and
Channel Display)
Volume Defines the Volume and Volume OSD behavior.
Settings (Volume Indicator, Max Volume and Switch On Volume)
Enable disable various interfaces and controls.
Lock
Keyboard, Remote Control, AV Inputs and Auto
Settings (USB,
Sensing)
the TV standby and Eco power, as well as the
Power DefinesOn
mode.
Settings Power
(StandBy Mode, Power On and Eco Power)
9
46 42 39HFL5784D L
LC11_PHILIPS_hospitality_EN_QG.indd 9
2013/07/22 17:41:53
How capture a clonefile from the TV to a USB
storage device
Configure standard TV settings
This menu will allow the configuration of the standard TV
parameters.
Options: Language, Picture, Sound, Caption settings, Child
Lock, EasyLink
Use of Slideshow application
The slideshow application will enable a basic signage mode.
1 Insert the USB stick with the graphic files.
2
Press MENU on the setup remote control to display the
setup menu.
3
4
Select Applications or Slideshow.
For testing and fine tuning, select Run from USB. The
TV will start displaying the files, with the parameters
configured in the Slideshow menu.
5
When all is confirmed, select Copy to TV. The graphic
files will be copied to the TV memory.
6
Select Configuration, Switch On and OSD, Switch On
Program or Slideshow in the main setup menu. Next
time the TV will switch On, will automatically start the
slideshow application.
1.
Insert a USB storage device into the TV USB terminal.
(It must have sufficient free space to hold a TV clonefile
– about 5 MB.)
2.
Press MENU on the setup remote control to display the
setup menu.
3.
4.
5.
6.
7.
8.
Scroll down to and select Upgrades.
Select Source and select USB then press OK.
Select Type and select Clone then press OK.
Select Direction and select from TV then press OK.
Select Execute and select Start then press the OK.
After the successful completion, Upgrade Completed!
Press OK to continue message appears on screen.
How install a clonefile from a USB storage
device to the TV
Configure the upgrading and cloning
settings
Preface:
The Upgrades section of the Hospitality TV setup menu has
three possible sources:
1. IP
2. USB
3. RF
Only the USB source is bidirectional, meaning that the TV
can either read from the USB, or write to the USB. The
IP and RF sources are unidirectional – read only. It cannot
write to them.
If the source USB is selected, there are 5 upgrade types
available:
1. All
2. Software (TV firmware(s))
3. Assets (Slideshow pictures)
4. Clone (TV settings and channel map)
5. P:I Key (Change TV between PPV ↔ FTG modes)
Of these, only the Assets and Clone types are bidirectional.
The All, Software, and P:I Key types are read only. So, if
either Assets or Clone is selected, an additional menu item:
Direction appears. There are two possible directions:
1. To TV
(reads data from the USB, copies it to the TV)
2. From TV (reads data from the TV, copies it to the USB)
1.
Insert the USB storage device containing the clonefile
into the TV USB terminal.
2.
Press MENU on the setup remote control to display the
setup menu.
3.
4.
5.
6.
7.
8.
Scroll down to and select Upgrades.
9.
After pressing OK, the TV will restart and initialize with
the new values
Select Source and select USB then press OK.
Select Type and select Clone then press OK.
Select Direction and select To TV then press the OK.
Select Execute and select Start then press the OK.
After the successful completion, Upgrade Completed!
Press OK to continue message appears on screen.
Note
• When selecting RF and its respective parameter, ensure that
this is the channel that will be used to stream the data and it is
not used by any video channel.
• RF cloning/upgrading must be used with a Gateway Network
Appliance (GNA) device. For more information on the GNA,
contact your Philips authorized agent or dealer.
10
46 42 39HFL5784D L
LC11_PHILIPS_hospitality_EN_QG.indd 10
2013/07/22 17:41:53
Installation of pay-per-view box
Multi RC
This section describes how to install a external pay-perview box.
Step 1 : Set the communication mode
You must setup the correct communication protocol before
you connect the Pay-per-View box to the TV. This section
describes how to select the communication mode.
1 Press MENU on the setup remote control to display the
setup menu.
Multi RC enables control of multiple TVs in a room without
any interference from each other’s remote control.
To enable Multi RC, each remote control is set to one of
the four colors - Blue, Green, Yellow or Red. Each TV in the
room is separately programmed to a remote control of
one of those colors. In this way, each TV responds to only
one RC that is set to the same color as the TV itself. This
prevents interference from each other’s remote control
when you watch multiple TVs in a room.
1 Press MENU on the setup remote control to display
the setup menu.
2 Select System.
3 Select MultiRC and the correct color code.
2
Select SPI and the appropriate option (3v3 , 5v).
Step 2 : Set the communication mode
Note
• Turn off your TV before you connect the pay-per-view box.
1
Insert the RJ12 cable of the Pay-per-View box into the
RJ12 connector of the TV.
2
Connect the other cables as directed by the Pay-perView provider.
After completing the connections of the cable, turn on
the TV.
3
4
4
Press ÎïÍÆ to select [Select a color code].
• The TV is configured to respond to the RC that is set to the
5
On the guest RC, press HOME (the menu button) and
the color button (same color as above) simultaneously,
for at least 5 seconds.
• The guest RC is set to the selected color.
same color.
Note
• The Guest RC defaults to Blue, and a remote which has been
set to any color can operate any TV which has not been
configured to a different color yet. Therefore, if 2 TVs are being
configured in the same space, then each TV/RC pair MUST
be set a their own color (one pair cannot be left as default,
otherwise both RCs will operate the TV which has not been
configured).
Press RECALL on the setup remote control and check
that the status of SPI ONLINE in page 4.
Watch your video on a USB storage
device
1 Connect your USB storage device to the TV.
2 Press MENU on the remote control to display the guest
3
menu.
Select Browse USB.
11
46 42 39HFL5784D L
LC11_PHILIPS_hospitality_EN_QG.indd 11
2013/07/22 17:41:53
P&F USA, Inc.
PO Box 2248, Alpharetta, GA 30023
P&F Mexicana, S.A. de C.V.
Av. La Palma No. 6, Col. San Fernando La Herradura.
Huixquilucan, Edo. de México.
C.P. 52787
Philips and Philips Shield are used under license of
Koninklijke Philips Electronics N.V.
Printed in China
A37QZUH / A37HYUH / A37HZUH / A37TYUH / A37TZUH
2EMN00058 ★★★★
* 2 E M N 0 0 0 5 8 *
46 42 39HFL5784D L
LC11_PHILIPS_hospitality_EN_QG.indd 12
2013/07/22 17:41:54