Download User Guide - Nightingale Care Beds Ltd
Transcript
the low bed specialist The SPIRIT™ Ultra Low Bed USER MANUAL It is the duty of all staff who handle the SPIRIT™ bed to read these:Guidance Notes for Safe Use Call our help line on 01865-409926 if you need advice or further instruction SPIRIT™ USER MANUAL - VERSION 01-2013 PAGE 1/20 Intended Use The Spirit™ Bed is intended for low to moderately acute patients in the medical and/or surgical area of the hospital. The Spirit™ Bed is also intended for use as a general-purpose variable height hospital bed for general care, post-operative, and general medicine wards. Standard Conventions Used in this Manual This manual includes information essential to the safety of the patient, personnel and equipment during the normal operation of the Spirit™ Bed. Before operating the Spirit™ Bed be sure you read and understood the contents of this manual. It is important that you use this equipment in accordance with the procedures outlined in this manual . As you read through this manual be alert to the three signal words. DANGER Information appearing under the DANGER caption concerns the protection of personnel from the immediate and imminent hazards that, if not avoided, will result in immediate, serious personal injury or loss of life in addition to equipment damage. WARNING Information appearing under the WARNING caption concerns the protection of personnel from potential hazards that can result in personal injury or loss of life in addition to equipment damage. CAUTION Information appearing under the CAUTION caption concerns the protection of personnel from potential hazards that can result in minor personal injury or equipment damage. IMPORTANT ELECTRICAL SAFEGUARDS DANGER • Plug the three prong electrical cord ONLY into a properly grounded 230 VAC, 50 cycle outlet. • DO NOT use an extension cord. • DO NOT permit the cord, wall outlet to become wet. • DO NOT operate the bed if the cord or outlet is damaged. • DO NOT operate the bed if any motor has malfunctioned or is damaged in any manner. During routine bed cleaning, always unplug the three-prong plug from grounded outlet. DO NOT roll the bed over the power cord. DO NOT entangle the cord on other objects. A pinched electric cord is dangerous and can become damaged. Be aware of the power cord location especially when moving the bed. AUXILIARY BATTERY NOTE PAGE 2/20 The battery is continuously charged as long as the bed’s power supply is plugged into a 230 VAC wall outlet. SPIRIT™ USER MANUAL - VERSION 01-2013 SPIRIT the low bed IMPORTANT MECHANICAL SAFEGUARDS WARNING DO NOT stand on the bed or concentrate weight on a single fiberglass deck panel. DO NOT use the bed without a mattress at least 4” (100mm) thick and of recommended dimensions. MATTRESS SPECIFICATIONS A mattress is not included with this bed. It is highly recommended that you use a 35.5” (900mm) wide mattress that is designed to conform to the bed length of 80” (2032mm). Possible patient ENTRAPMENT Hazard if using non-specified mattress, patient entrapment may result in an injury. Use only a mattress of recommended specifications with this bed. • DO NOT use without a special mattress specifically designed to bend and conform to the shape of the bed. • DO NOT use a water filled or gel filled mattress on this bed. GENERAL PRECAUTIONS • Do not use headboards or footboards from other manufacturers. • Ensure all deck hinges are properly aligned before raising head or knee sections. • Ensure that the headboard and footboard are properly attached to the frame. • This bed is rated to 35 stone / 227kg. DO NOT overload the bed. The combined weigh of patients, visitors, mattress and bedding must NOT exceed 35 stone / 227kg. The maximum load on either side rail is 12 stone / 77kg. At the installation The person supplying and setting up the bed will show staff how it operates. All staff that may come into contact with the bed whether nurses, cleaners or porters will need to understand how the bed operates. A further training session may be required for the above standard to be met and in order to consolidate staff competence. REMEMBER: Training in the use of equipment is a legal requirement The prerequisites for using the Spirit Ultra Low bed are that it has been electrically tested and that the person operating it has had instruction in its use. The bed must also have an up-to-date hospital inspection record. SPIRIT™ USER MANUAL - VERSION 01-2013 PAGE 3/20 WARNING Familiarise yourself with the various functions. Care should be taken that there is no wall - mounted obstruction to prevent the bed moving vertically. Ensure that nothing can get trapped underneath the bed when it is lowered. (Examples: slippers / pillows / walking sticks etc.) It is essential that the power cable does not get trapped between moving parts. Check before lowering the bed. DO NOT allow patients to fall on the bed. DO NOT Jump on the bed. Each of the preceding impacts can permanently damage either Hi/Lo motor resulting in an inoperable bed. In the case of an inoperable bed due to a damaged Hi /Lo motor remove the bed from service and replace the Hi/Lo motor immediately. If left unattended, a damaged Hi/ Lo motor could result in patient injury. ONLY use original manufacturers replacement parts PAGE 4/20 SPIRIT™ USER MANUAL - VERSION 01-2013 SPIRIT the low bed Bed Positioning Bed Elevation - HI-Lo Function To raise the bed, press the BED UP arrow on the staff control pad. See DIA 10. Release the button when the desired level is reached. See DIA 11 DIA 10 DIA 11 DIA 12 DIA 13 DIA 14 DIA 15 DIA 16 DIA 17 DIA 18 DIA 19 DIA 20 DIA 21 To lower the bed, press BED DOWN arrow on the staff control pad. See DIA 12. Release the button when the desired level is reached. See DIA 13 Head Elevation - Head Motor Function To raise the head section of the bed, press the HEAD UP arrow on the staff control pad. See DIA 14. Release the button when the desired level is reached. See DIA 15 To lower the head section of the bed, press the HEAD DOWN arrow on the staff control pad. See DIA 16. Release the button when the desired level is reached. See DIA 17 Knee Elevation - Foot Motor Function To raise the Knee section of the bed, press the KNEE UP arrow on the staff control pad. See DIA 18. Release the button when the desired level is reached. See DIA 19 To lower the Knee section of the bed, press the KNEE DOWN arrow on the staff control pad. See DIA 20. Release the button when the desired level is reached. See DIA 21 SPIRIT™ USER MANUAL - VERSION 01-2013 PAGE 5/20 Auto Contour Activate Auto Contour In order to prevent patients from sliding towards the footboard as the head section is elevated, it may be beneficial to use the auto contour function. This function will automatically raise/lower the knee section whenever the head section is raised or lowered (DIA 22). To activate auto contour, simply press the CONTOUR button at the bottom right corner of the staff control pad (DIA 23). When the green light is illuminated, the auto contour function is active. DIA 22 DIA 23 Staff and Emergency Functions TreNdelenburg and Reverse Trendelenburg Operation CAUTION Patient discomfort may result from normal operation of the Trendelenburg or Reverse Trendelenburg function. Trendelenburg and Reverse Trendelenburg modes should only be used on the advice of a medical practitioner. WARNING The Spirit™ bed may shift during Trendelenburg or Reverse Trendelenburg activation. Tredelenburg or Reverse Trendelenburg must be operated ONLY after the bed has been stabilized in the Central Lock & Steer LOCK position. Activate Trendelenburg Mode 1. Press and hold the TREND button on the staff control pad. Release the button once the desired bed angle between 0º and 15º is reached. See DIA 24 and 25 2. To return the bed to level, press and hold the REV TREND button until the bed automatically stops. DIA 24 DIA 25 DIA 26 DIA 27 Activate Reverse Trendelenburg Mode 1. Press and hold the rev. TREND button on the staff control pad. Release the button once the desired bed angle between 0º and 13º is reached. See DIA 26 and 27 2. To return the bed to level, press and hold the TREND button until the bed automatically stops. PAGE 6/20 SPIRIT™ USER MANUAL - VERSION 01-2013 SPIRIT the low bed Chair Mode The “Chair” function allows patients to be placed in an upright postion. WARNING Chair mode must be operated only after the Central Lock & Steer pedal has been put in the LOCK position. Activate Chair Mode Press and hold the CHAIR button on the staff control pad (DIA 28). Release the button once the chair configuration is reached (bed will stop automatically) See DAI 29. The green `Chair’ light will illuminate once the proper Reverse Trendelenburg angle has been achieved. To deactivate the Chair Mode, press and hold the CHAIR button until the bed is flat. The bed will stop automatically. DIA 28 DIA 29 CPR (Cardiopulmonary Resuscitation) Mode CAUTION Improper use of CPR mode may cause patient injury. Once activated, CPR function will lower head and knee sections to flat position automatically. To interrupt CPR function, touch any other button on the keypad. Activation of the CPR control allows one-touch flattening of all bed surfaces. Activate CPR Mode Press the CPR button on the staff control pad one time. The head section and knee section will lower to flat position. See DIA 30 and 31. The CPR mode does not need deactivation. Simply resume head and knee-foot operation once the CPR action is complete. DIA 30 DIA 31 To Interrupt the CPR mode, touch any other function on the keypad. SPIRIT™ USER MANUAL - VERSION 01-2013 PAGE 7/20 Patient Lockouts Activate Individual Function Lockouts Patient Lock-out restricts the patient from activating various bed features via the quad rail control pad. The degree of restriction depends on the lock out option selected. Staff may choose to lock patients access to one, two, or all three bed functions. To restrict a function, press the “PATIENT LOCK” button under that particular function (see DIA 32). The lock icon will illuminate when the function is locked-out for the patient. To unlock, press the same button again. When the light is not illuminated, the patient has access to that function. DIA 32 NOTE: When patient functions have been locked, the staff footboard control pad remains active. Activate Total Lock-out To completely restrict access to all bed functions from all control points (staff and patient controls), use the total lock-out function. Press and hold all three lock-out buttons at the same time (DIA 33). All functions on the staff footboard control pad and all patient controls are unavailable. Total lock-out is active when all three lock-out buttons flash sequentially. DIA 33 To deactivate the total lock-out feature, repeat the process by pressing and holding all three lock-out buttons at the same time. WARNING When left unattended, the bed should be lowered to its lowest position with the ”Bed Elevation” function locked-out in order to reduce the risk of patient injury. PAGE 8/20 SPIRIT™ USER MANUAL - VERSION 01-2013 SPIRIT 3.5.3 Spirit™ & Spirit Plus™ Power Status Indicator the low bed The enhanced footboard staff control on the Spirit Select™ is equipped with an Spirit™ Power Status Indicator integrated power status indicator. This cluster of 3 discrete icons indicate the realtime status of power available to operate the bed. The icons will illuminate respectivestaff of thecontrol source ofon power, operationnecessary of the battery bed chargingfunctions circuit, and The enhanced footboard thetheSpirit the level of battery power. Select™ is equippedThe with an integrated power status are performed to extend battery is continuously charged when connected to the CB10 control box and indicator. This cluster of 3 icons indicate the If the battery power long the bed isdiscrete plugged into an AC power outlet. battery voltage dropsas below realtime status of power available to operate the bed.disrupted as possible and discharge ensure 18VDC, battery power will be automatically to prevent further which could impact theofbattery’s ability toof fully recharge. When the bedfunctions is plugged The icons will illuminate respective the source emergency back into an AC power outlet, battery power will be automatically restored. power, the operation of the battery charging circuit, remain available when Indicator LED is Solid GREEN and the level of battery power. needed. Bed is connected to an AC power outlet and operating on AC power. The battery is connected to the CB10 control The battery is continuously when box and ischarged fully charged. Bed connected is ready to operate on battery power if required. This is the optimum operating for the the bed. to the CB10 control condition box and bed is plugged into Indicator LED is Flashing RED Indicator is Flashing GREEN an AC power outlet. If the LED battery voltage drops Bed is disconnected from an AC power outlet and Bed ispower connected to an power outlet and operating on AC operating power. The battery is connected to theAlthough CB10 controlthe below 18VDC, battery will beACautomatically has been on battery power. box but is currently recharging. disrupted to prevent further discharge which could battery is connected to the CB10 control box, it has is Alternating and RED impact the battery’sIndicator ability toLED fully recharge. Flashing When GREEN exhausted its battery power. Reconnect bed to an AC IMPORTANT: Bed may not reliably operate on battery the bed is plugged back into an AC power outlet, power power outletif required. as soon as possible and allow battery Bedautomatically is connected to anrestored. AC power outlet and operating on AC for power. The battery is connected to the CB10 control battery power will be to charge 24hr. box but not holding proper charge. Service bed and/or replace battery immediately. IMPORTANT: At this point, reliable bed operation OR Indicator LED is Solid GREEN cannot be battery guaranteed although somefor 24hr. bed The battery is not connected to the CB10 control box. Connect to CB10 and allow battery to charge Bed is connected Indicator to an AC power outlet and functionality may still be available. Exercise caution LED is Solid RED operating on AC power. The battery is AC connected operating bed as theThe bed williscease operation Bed is disconnected from an power outlet and is operatingthe on battery power. battery connected to the boxfully and has not yet exhausted available warning. battery power. Bed is OK to operate on battery power but to the CB10 control CB10 boxcontrol and is charged. Bed is thewithout should bepower connected to an AC power outlet ready to operate onitbattery if required. This is as soon as is possible to recharge the battery. IMPORTANT: Exercise caution the bed on battery power. Ensure that only vital and necessary bed the optimum operating condition for the bed.when operatingNo Indicator functions are performed to extend battery power as long as possible andLED ensureillumination emergency functions remain available when needed. IMPORTANT: Bed may NOT operate. Indicator LED is Flashing GREEN Indicator LED is Flashing RED The bed has been disconnected from an AC power Bed is connected to an power outlet BedAC is disconnected fromand an ACoperating power outlet and has been operating on battery power. Although the battery is outlet and the battery is disconnected from the CB10 connectedistoconnected the CB10 control has exhausted its battery power. Reconnect bed to an AC power outlet as soon on AC power. The battery to box, the itCB10 control box. Reconnect bed to an AC power outlet as possible and allow battery to charge for 24hr. control box but is currently recharging. andcannot allow toalthough chargesome for bed 24hr. IMPORTANT: At this point, reliable bed operation be battery guaranteed functionality may still be available. Exercise caution operating the bedor as the bed will cease operation without warning. Indicator LED is Alternating Flashing The bed has a faulty connection or component GREEN and REDNo Indicator LED illumination IMPORTANT: Bed may NOT operate. (CB09 control box, CB10 control box, battery, and/ IMPORTANT: BedThemay notbeen reliably operate bed has disconnected from an on AC power outlet and the battery is disconnected from the CB10 control box. connection cable). Confirm all connections and battery power if required. Bedto is anallowor Reconnect bed an connected AC power outlettoand battery to charge for 24hr. begin troubleshooting potentially faulty components. OR operating on AC power. The AC power outlet and The bed has a faulty connection or component (CB09 control box, CB10 control box, battery, and/or connection battery is connected to the CB10 control box but not or cable). Confirm all connections and begin troubleshooting potentially faulty components. holding proper charge. Service bed and/or replace The bed has been disconnected from an AC power OR battery immediately.The bed has been disconnected from an AC power outlet battery been disengaged automatically outletand and thethe battery has been has automatically from the battery circuit because the voltage has dropped below 18VDC. Reconnect bed to an AC power outlet and allowthe disengaged from the battery circuit because OR battery to charge for 24hr. The battery is not connected to the CB10 control voltage has dropped below 18VDC. Reconnect bed ACa power outlet andwhen allow In-house testing has demonstrated new back-up battery, fully charged, has sufficient box. Connect battery to CB10 and allow battery to to anthat power to deliver the equivalent of approximately 5 CPR cycles with a patient weight of 250 lbs. battery to charge for 24hr. charge for 24hr. Battery power discharge rate depends upon factors such as patient weight, age of battery, ambient temperature and humidity, and the number of charge/discharge cycles the battery has been NOTE: Note: heavier the patient, the faster battery power will be exhausted Indicator LED is Solid REDsubjected to. For example, the In-house testing has demonstrated that a new back-up battery, during battery powered bed operation. Conversely, the lighter the patient, battery power may whenpowered fully charged, has sufficient power to deliver the equivalent Bed is disconnected from an AC power outlet and of is battery offer a longer duration bed operation. of approximately 5 CPR 20 Stone operating on battery power. battery is connected © Carroll Hospital Group Inc. cycles with a patient weight of 1-70-001-H UserThe Manual - Spirit™ Bed Page 47 of 120 (120kgs) to the CB10 control box and has not yet exhausted power discharge rate depends upon factors such the available battery power. Bed is OK to operate Battery as patient weight, age of battery, ambient temperature and on battery power but it should be connected to an humidity, and the number of charge/discharge cycles the battery AC power outlet as soon as is possible to recharge has been subjected to. For example, the heavier the patient, the faster battery power will be exhausted during battery powered the battery. bed operation. Conversely, the lighter the patient, battery power IMPORTANT: Exercise caution when operating may offer a longer duration of battery powered bed operation. the bed on battery power. Ensure that only vital and SPIRIT™ USER MANUAL - VERSION 01-2013 PAGE 9/20 Patient Quad Rail Control Pad Head Elevation function To raise the head section of the bed, press the Head UP arrow, release the button when the desired level is reached. To lower the head section of the bed, press the HEAD Down arrow, release button when the desired level is reached. Knee Elevation Function To raise the knee section of the bed, press the KNEE UP arrow, release button when the desired level is reached. To lower the knee section of the bed, press the KNEE DOWN arrow, release button when the desire level is reached. CAUTION It is recommended that you de-activate auto contour on the staff control pad, when patient has full control of head and foot profile functions. PAGE 10/20 SPIRIT™ USER MANUAL - VERSION 01-2013 SPIRIT the low bed Quad-rail staff control pad Head Profile Elevation Function To raise the head section of the bed, press the HEAD UP arrow, release the button when the desired level is reached. To lower the head section of the bed, press the HEAD DOWN arrow, release button when the desired level is reached. Knee Profile Elevation Function To raise the knee section of the bed, press the KNEE UP arrow, release button when the desired level is reached. To lower the knee section of the bed, press the KNEE DOWN arrow, release button when the desired level is reached. BeD High/Low Elevation Function To raise the bed, press the BED UP arrow, release button when the desired level is reached. To lower the bed, press BED DOWN arrow, release button when the desire level is reached. SPIRIT™ USER MANUAL - VERSION 01-2013 PAGE 11/20 3.14.4 3.14.4 Quad QuadSiderails Siderails 3.14.4 Quad Siderails Your YourSpirit SpiritPlus™ Plus™or orSpirit SpiritSelect™ Select™bed bedcomes comeswith withmoulded mouldedplastic plasticQuad Quadsiderails siderailsas asstandard standardequipment. equipment. Your Spirit Plus™ or Spirit Select™ bed comes with moulded plastic Quad siderails as standard equipment. Operation Operationof ofthe theQuad QuadSiderails Siderails Operation of the Quad Siderails ItItisisimportant importantthat thatcaregivers caregiversknow knowhow howtotooperate operatethe theQuad Quadsiderails siderailssafely. safely. The TheQuad Quadsiderails siderailslock lockinin Itthe is UP important that caregivers know how to operate the Quad siderails safely. The Quad siderails lock in the position and enables patient ingress, egress, and transfer in the DOWN position. UP position and enables patient ingress, egress, and transfer in the DOWN position. the UP position and enables patient ingress, egress, and transfer in the DOWN position. In Inthe theUP UPposition, position,the theQuad Quadsiderails siderailsprovide provide In the UP position, the Quad siderails In the UP position, the Quad siderails providepositive positive patient location and support helping toto positive patient location and supportprovide helping patient location and support helping to protect positive patient location and support helping to the protect protectthe thepatient patientfrom fromthe thepotential potentialofoffalling falling patient from the potential of falling from bed. protect the patient from the potential of the falling from bed. fromthe the bed. from the bed. IMPORTANT: An Anaudible audible“click” “click”should shouldbebe heard IMPORTANT: IMPORTANT: An Siderails audible “click” should beheard heard 3.14.4 Quad when each siderail assembly has been completely IMPORTANT: An audible “click” should be heard when siderail assembly has been wheneach each siderail assembly haslocking beencompletely completely rotated intosiderail the UP position asas the mechanism when each assembly has been completely rotated into the UP position the locking rotated into the UP position as thebed locking Your Spirit Plus™ or Spirit Select™ comes with moulded plastic Quad siderails as standard equipment. engages. rotated into engages. the UP position as the locking mechanism mechanism engages. mechanism engages. Operation of the Quad Siderails Operation of the Quad Siderails It isDOWN important that caregivers know how to operate the Quad siderails safely. The Quad siderails lock in The TheDOWN DOWNposition, position, the Quad siderails fully rotate The position,the theQuad Quadsiderails siderailsfully fullyrotate rotate the UP position and enables patient ingress, egress, and transfer in the DOWN position. The DOWN position, the Quad siderails fully rotate out of the way to provide unimpeded and outof ofthe theway waytotoprovide provideunimpeded unimpededand andunassisted out out of the way to provide unimpeded and unassisted patient ingress totoand from unassisted patient ingress andegress egress from the In the UP position, theegress Quad siderails provide patient ingress to and from the bed andthe also unassisted patient ingress to and egress from the bed and also enables patient transfer by staff. bed and also enables patient transfer by staff. positive patient location and support helping to enables patient transfer by staff. bed andthe alsopatient enables patient transfer by staff. protect from thewill potential oflock falling IMPORTANT: not lock in IMPORTANT: Thesiderails siderails will in the IMPORTANT:The The siderails will notnot lock inthe the from the bed. IMPORTANT: The siderails will not lock in the DOWN DOWN position. DOWNposition. position. DOWN position. An audible “click” should be heard IMPORTANT: when each siderail assembly has been completely rotated into the UP position as the locking mechanism engages. Raising Raisingthe theFoot FootSiderails Siderails Raising the Foot Siderails Raising the Foot Siderails Gently Gentlyrotate rotatethe thefoot footsiderail siderailtotothe theUP UP The DOWN position, the Quad siderails Gently rotate the foot siderail to UP the fully UP rotate Gently rotate the foot siderail to the position. position. The Thefoot footsiderail siderailwill willfirst firstarc arc out of the way to provide unimpeded and position. The foot siderail will first arc toward position. The foot siderail arc toward foot end ofofthe bed then towardthe the foot end thewill bedfirst then unassisted patient ingress to and egress from the the foot endfoot ofthe the bed then back towards the toward the end of the bed then back towards head end of the bed back towards the head end of the bedas as bed and also enables patient transfer byUP staff. endto of the bed as it rotates to the back towards the head end of the bed as ithead UP position. itrotates rotates tothe the UP position. position. itIMPORTANT: rotates to the UP position. The siderails will should not lock in the IMPORTANT: audible “click” IMPORTANT:An An audible “click” should IMPORTANT: An audible “click” should DOWN position. IMPORTANT: An audible “click”has should be heard when the foot siderail been be heard when the foot siderail has been be heard when the foot siderail has been be heard when thetoto foot siderail has been completely raised the UP position as completely raised the UP position as completely raised to the UP position as the completely raised to theengages. UP position as the mechanism thelocking locking mechanism engages. locking mechanism engages. the locking mechanism engages. Lowering Loweringthe theFoot FootSiderails Siderails Lowering the Foot Siderails Raising the Foot Siderails Lowering the Foot Siderails Depress Depressthe thegreen greenpush pushbutton buttonthen then Depress the green push button then gently push down on the foot siderail. Gently rotate the foot siderail to the UP gently push down on the foot siderail. Depress thedown green push button then the gently gently push on the foot siderail. The foot siderail will first arc towards position. The foot willtowards first arcthe The foot siderail willsiderail first arc push down on the foot siderail. The foot The foot siderail will first arc towards foot end of the bed back towards toward the foot endthen of the bed then the foot end of the bed then back towards siderail will first arcthen towards the foot to end of foot end of the bed back towards the end ofof the bed as back towards the head ofrotates the bed thehead head end the bedend asitthe it rotates toas of the bed then back towards head end head end of the bed as it rotates to the DOWN position. it rotates toposition. the UP position. the DOWN the bed as position. it rotates to the DOWN position. the DOWN IMPORTANT: foot siderails will not IMPORTANT: An “click”will should IMPORTANT:The Theaudible footsiderails siderails will notlock IMPORTANT: The foot not IMPORTANT: The foot siderails will not lock in the DOWN position. be heard when the foot siderail has been lock in the DOWN position. in the DOWN position. lock in the DOWN completely raised position. to the UP position as the locking mechanism engages. Lowering the Foot Siderails 1-70-001-H User Manual - -Spirit™ 1-70-001-H User Manual Spirit™ Bed Depress the green pushBed button 1-70-001-H User Manual - Spirit™ Bed ©©Carroll Page CarrollHospital HospitalGroup GroupInc. Inc. Page67 67ofof120 120 then © Carroll Hospital Group Inc. Page 67 of 120 gently push down on the foot siderail. PAGE 12/20 SPIRIT™ USER MANUAL - VERSION 01-2013 The foot siderail will first arc towards the foot end of the bed then back towards the head end of the bed as it rotates to SPIRIT the low bed Raising the Siderails Raising the Head Head Raising the Siderails Head Siderails Gently rotate the head siderail to UP Gently the siderail to the the UP UP Gently rotate rotate thehead head siderail toarc the position. The head siderail will first position. The head siderail will will first arc position. The head siderail first arc toward the head end of the bed then back toward the head end of the bed then back toward the head endofofthe thebed bedasthen back towards the foot end it towards the foot end of the bed as itit rotates towards the foot end of the bed as rotates to the rotates to position. the UP UP position. position. to the UP IMPORTANT: “click” should be IMPORTANT: An Anaudible audible “click” should IMPORTANT: An audible “click” should be heard when the head siderail has been be heard the head siderail has been heard whenwhen the head siderail has been completely completely raised raisedto theUP UPposition positionas the completely raised totothe the UP position asasthe the locking mechanism engages. lockingmechanism mechanism engages. engages. locking Lowering Head Siderails Lowering the Head Siderails Raisingthe the Head Siderails Depress the green push button then Depress Depress the the green greenpush pushbutton buttonthen then gently gently push on the siderail. gently push down down the head head siderail. push down on theonhead siderail. The head The head siderail will first arc towards the The head siderail will first arc towards the of siderail will first arc towards the head end head end of the bed then back towards head endthen of the bed then back towards the bed back towards the foot end of the the foot end of bed as to the of the the bedDOWN as it it rotates rotates to bedfoot as itend rotates to the position. the DOWN position. the DOWN position. IMPORTANT: The head siderails will not IMPORTANT: The head lock in the DOWN IMPORTANT: The position. head siderails siderails will will not not lock in the DOWN position. lock in the DOWN position. Integrated Features Integrated Features BED operation Staff Siderail Central Lock Controls and Steer System Staff Siderail Controls Neutral Angle Gauges Angle Gauges Mode used only to manoeuvre the All casters swivel and roll All four siderails have integrated angle gauges: All four haveThis integrated bed in asiderails tight area. mode angle gauges: •• The head angle allows the bed move forward, The headtosiderail siderail angle gauge gauge displays displays the the angle of the head section of the backward or of sideways. angle the head section of the mattress mattress deck. deck. SPIRIT™ USER MANUAL - VERSION 01-2013 •• The Head The foot foot siderail siderail angle angle gauge gauge displays displays the the Head Siderail Siderail Trendelenburg or reverse Trendelenburg angle Angle Trendelenburg or reverse Trendelenburg angle Angle Gauge Gauge DIA 36 DIA 35 DIA 34 The control The head head siderails siderails incorporate incorporate integrated integrated staff staffWARNING control that that offers offers staff staff control of basic bed operations: control of basic bed operations: •• Head UP/DOWN, HeadUnintended UP/DOWN,bed movement may occur if bed is left in either of the mobilized positions, “STEER” •• Knee/Foot UP/DOWN or “NEUTRAL”. Knee/Foot UP/DOWN •• Bed UP/DOWN Never leave the bed unattended in either the “STEER” or “NEUTRAL” positions. Bed UP/DOWN IMPORTANT: operation from this control is when patient Do Bed not move the bed until mobilization system hasthe been activated. IMPORTANT: Bed operation from thisthe control is disabled disabled when the patient lock-outs are activated. lock-outs are activated. MODEFUNCTIONPEDAL POSITION Lock Patient Siderail Patient Siderail Controls Controls Typical mode used to stabilize the Casters DO NOT The head siderails incorporate integrated patient control that The incorporate control that offers offers patient patient bed head from siderails shifting. This mode integrated patient swivel or roll control of basic bed operations: control of basic bed operations: prevents the bed from moving •• Head UP/DOWN, forward, backward or sideways. Head UP/DOWN, •• Knee/Foot UP/DOWN Knee/Foot UP/DOWN STEER •• Nurse Call Nursewhen Call feature feature Mode used attempting to Two head end casters swivel; IMPORTANT: Bed operation from control is when IMPORTANT: operation from this this is disabled disabled when the the patient patient steer the bed inBed a desired direction. control Two foot end casters lock-outs are activated. lock-outs are activated. All caster wheels can still rotate, DO NOT swivel; IMPORTANT: The Call if patient enabling the bed to Nurse move forward remains Allactive casters IMPORTANT: The Nurse Call feature feature remains active if roll patient lock-outs lock-outs have been activated. or backward. have been activated. PAGE 13/20 Foot Foot Siderail Siderail Angle Gauge Angle Gauge Mobilization Mobilization The bed is mobile in either the “NEUTRAL” or “STEER” modes. Use either of these modes depending on the situation, when bed mobility is needed. Activate Steer Mode 1. Fully depress the right side of the central lock & Steer pedal at either end of the bed. See DIA 36. 2. Slide the bed sideways, in a back and fourth motion, at the foot end of the bed until the steering casters are engaged. See DIA 37. NOTE: When the ”NEUTRAL” mode is activated properly, the bed should move freely without any unusual noises. If any clicking noises are present in the neutral mode, stop and check that the pedal is level. Adjust, if necessary. DIA 37 DIA 38 Activate Neutral Mode 1. Press or lift the pedal with your foot until the pedal is level. Stabilization DIA 39 The bed is stable in the ”LOCK” mode. Use this mode whenever the bed is left unattended or when the bed needs to remain stable. Activate Lock Mode 1. Fully depress the left side of the Central Lock & Steer pedal at either end of the bed. See DIA 39 DIA 40 PAGE 14/20 SPIRIT™ USER MANUAL - VERSION 01-2013 SPIRIT the low bed Optional “Easy Bed” Extension/Retraction System 3.12 3.12Optional 3.12 Optional 3.12Optional Optional “Easy “EasyBed” “Easy Bed” “Easy Extension/Retraction Bed” Extension/Retraction Bed”Extension/Retraction Extension/Retraction System System System System To accommodate the physical needs of taller patients, while maintaining the easy ofbed frequent bed movement 3.12 Optional 3.12 “Easy Optional Bed” Extension/Retraction “Easy Bed” Extension/Retraction System System To To accommodate accommodate To To accommodate accommodate thethe physical physical the needs the needs physical physical of of taller taller needs needs patients, patients, of taller of taller while while patients, patients, maintaining maintaining while while maintaining themaintaining the easy easy of of the frequent frequent the easy easy of bed bed frequent ofmovement frequent movement bed about movement about movement about about about space confined healthcare facilities, Carroll Hospital Group offers anBed” optional “Easy Bed” extension space space confined confined space space healthcare healthcare confined confined facilities, healthcare facilities, healthcare Carroll Carroll facilities, facilities, Hospital Hospital Carroll Carroll Group Group Hospital Hospital offers offers Group an Group an optional optional offers offers an “Easy “Easy an optional optional Bed” Bed” extension “Easy extension “Easy Bed” system extension system extension that that system system that that To accommodate the physical To accommodate needs of taller the patients, physical needs while maintaining of taller patients, the easy while of maintaining frequent bedthe movement easy of frequent about bed movement about allows allows for for easy allows easy allows and and for rapid for easy rapid easy extension/retraction and extension/retraction and rapid rapid extension/retraction extension/retraction of of thethe mattress mattress ofan the ofHospital deck the deck mattress mattress byGroup by 4 of inches 4deck inches deck by (102 (102 by 4 optional inches mm) 4 mm) inches from (102 from (102 80” mm) 80” mm) (2032 (2032 from from mm) 80” mm) 80” (2032 to to (2032 mm) mm) to tomm) from system that allows for easy and rapid extension/retraction the mattress deck by 4 inches (102 space confined healthcare space facilities, confined Carroll healthcare Hospital facilities, Group offers Carroll optional “Easy offers Bed” extension an system “Easy that Bed” extension system that 84” 84” (2134 (2134 84” mm). (2134 No (2134 No tools mm). tools mm). areare No required No required tools tools are toare to perform required required bed tobed perform toare “Easy perform “Easy Bed” bed Bed” extension/retraction “Easy extension/retraction “Easy Bed” extension/retraction extension/retraction operations. operations. operations. operations. allows formm). easy and rapid allows extension/retraction for easy and rapid ofperform the extension/retraction mattress deckrequired by of 4bed inches the mattress (102 mm) deck from by 480” inches (2032 (102 mm) mm) to from 80” (2032 mm) to 80” (2032 mm) to84” 84” (2134 mm). No tools toBed” perform bed “Easy Bed” extension/retraction 84” (2134 mm). NoSpirit™ tools 84” are (2134 required mm). tobeen No perform tools are bed required “Easy Bed” to perform extension/retraction bed “Easy Bed” operations. extension/retraction operations. If If your your Spirit™ Spirit™ If your If bed your bed has has Spirit™ been been bed equipped bed has equipped has been with equipped with equipped the the optional optional with with the “Easy the “Easy optional optional Bed Bed Extension” “Easy Extension” “Easy Bed Bed system, Extension” system, Extension” the the system, bed bed system, will will the be be the outfitted bed outfitted bed will will be with with be outfitted outfitted withbed will operations. If your Spirit™ bed haswith been equipped with the optional “Easy Bed Extension” system,with the If your Spirit™ bed has been If an your equipped Spirit™ bedan has the been optional equipped “Easy Bed with Extension” the optional system, “Easy the Bed bed Extension” will be outfitted system, the with bed will be outfitted with two two clamping clamping two knobs two clamping knobs clamping and and knobs an extendable knobs extendable andand an foot extendable foot extendable deck deck section foot section foot deck of deck of the section the mattress section mattress of the of deck the deck mattress mattress as as shown shown deck deck below. as below. as shown shown below. below. be outfitted two clamping knobs an extendable deck of as the mattress two with clamping knobs andtwo an extendable clamping knobs footand deck and an section extendable of the foot mattress deckfoot deck section as shown of thesection mattress below. deck shown below. deck as shown below. 3.12 3.12Optional 3.12 Optional 3.12Optional Optional “Easy “EasyBed” “Easy Bed” “Easy Extension/Retraction Bed” Extension/Retraction Bed”Extension/Retraction Extension/Retraction System System System System Clamping Knobs (viewed Clamping from foot Knobs endfoot of(viewed bed) foot end Extendable of bed) Foot Deck Section Extendable Foot Deck Section Clamping Knobs (viewed from end from of bed) Extendable Foot Deck Section ToClamping To accommodate accommodate To To accommodate accommodate the the physical physical the needs the needs physical physical of of taller taller needs needs patients, patients, ofend taller of bed) taller while while patients, patients, maintaining maintaining while while maintaining the maintaining the easy easy of of the frequent frequent the easy easy of bed bed frequent of movement frequent movement bedbed about movement about movement about about (viewed (viewed from from (viewed foot (viewed foot end from end of from of bed) foot bed) foot end of of bed) Extendable Extendable Foot Extendable Foot Extendable Deck Deck Section Foot Section Foot Deck Deck Section Section Clamping Knobs Clamping Knobs Clamping Knobs Knobs Bed Extension Procedure Bed Extension Procedure space space confined confined space space healthcare healthcare confined confined facilities, healthcare facilities, healthcare Carroll Carroll facilities, facilities, Hospital Hospital Carroll Carroll Group Group Hospital Hospital offers offers Group anGroup an optional optional offers offers an “Easy “Easy an optional optional Bed” Bed” extension “Easy extension “Easy Bed” Bed” system extension system extension that that system system that that Bed allows Extension Procedure Bed BedExtension Bed Bed Extension Extension Procedure Procedure Procedure Procedure allows forExtension for easy allows easy allows and and for rapid for easy rapid easy extension/retraction and extension/retraction and rapid rapid extension/retraction extension/retraction of of thethe mattress mattress of the ofdeck the deck mattress mattress byby 4 inches 4deck inches deck by (102 (102 by 4 inches mm) 4 mm) inches from (102 from (102 80” mm) 80” mm) (2032 (2032 from from mm) 80” mm) 80” (2032 to to (2032 mm) mm) to to 84” 84” (2134 (2134 mm). 84” mm). 84” (2134 No (2134 No tools mm). tools mm). areare No required No required tools tools are toare to perform required perform required bed tobed perform to“Easy perform “Easy Bed” bed Bed” bed extension/retraction “Easy extension/retraction “Easy Bed” Bed” extension/retraction extension/retraction operations. operations. operations. operations. If If your your Spirit™ Spirit™ If your Ifbed your bed Spirit™ has has Spirit™ been been bed equipped bed has equipped has been been with equipped with equipped thethe optional optional with with the “Easy the “Easy optional optional Bed Bed Extension” “Easy Extension” “Easy BedBed system, Extension” system, Extension” thethe system, bed bed system, willwill the bebe the outfitted bed outfitted bed willwill be with with be outfitted outfitted with with two two clamping clamping two knobs two clamping knobs clamping and and an knobs an extendable knobs extendable andand an an foot extendable foot extendable deck deck section foot section foot deck ofdeck of the section the mattress section mattress of the ofdeck the deck mattress mattress asas shown shown deck deck below. as below. as shown shown below. below. Knob clamped 1. Knob Knob unclamped and Knob unclamped clamped and contacting retention bracket contacting retention bracket 1. Elevate bed to comfortable 1. Elevate working bedunclamped height. tounclamped comfortable Unclamp working height. Unclamp bracket 2. Grasp 2. Grasp by thefootboard corners as bracket shownby the corners as shown Knob Knob and and Knob Knob unclamped unclamped and andfootboard Knob Knob clamped clamped Knob Knob clamped clamped the footboard bracket slide the mechanism footboard bracket by turning slidebracket both mechanism by bracket turning bothsmoothly above. Gently and above. pullGently away and fromsmoothly the headpull away from the head retention retention bracket retention retention bracket contacting contacting contacting contacting knobs counter-clockwiseknobs until they counter-clockwise come to stop on until they come stop on the footboard of thetobed until of the bracket bed untilslide the footboard bracket slide their retention brackets. their retention brackets. mechanism contacts its mechanical mechanism stops. contacts its mechanical stops. 1. 1. Elevate Elevate 1.bed Elevate tocomfortable Elevate to comfortable comfortable bedbed to comfortable to working comfortable working height. height. working working Unclamp Unclamp height. height. Unclamp 2.Unclamp 2. Grasp Grasp footboard footboard 2. 2. Grasp Grasp bracket footboard bracket footboard byby the bracket the bracket corners corners by by the asas the shown corners shown corners as shown shown Elevate bedbed to1. working height 2. Grasp footboard bracket byasthe corners as thethe footboard footboard thebracket the footboard bracket footboard slide slide bracket mechanism bracket mechanism slide slide mechanism byby mechanism turning turning both byboth by turning turning both both above. above. Gently Gently above. and above. and smoothly Gently smoothly Gently and pull and smoothly pull away smoothly away from pull from pull the away the away head head from from thethe head head Unclamp the footboard bracket slide mechanism shownabove. Gently and smoothly pull knobs knobs counter-clockwise counter-clockwise knobs knobs counter-clockwise counter-clockwise until until they they come until come until to they to stop they stop come on come onto stop to stop onof onthe of the bed bed until ofuntil the ofthe the the bed footboard bed footboard until until thebracket the footboard bracket footboard slide slide bracket bracket slide slide their their retention retention their their brackets. retention brackets. retention brackets. brackets. mechanism mechanism mechanism contacts contacts mechanism its its contacts mechanical mechanical contacts its mechanical stops. stops. mechanical stops.until the by turning both knobs counter-clockwise until away from theitsheadof thestops. bed (viewed (viewed from from (viewed foot (viewed foot end from end of from of bed) foot bed) foot endend of bed) of bed) Extendable Extendable Extendable Foot Extendable Deck Deck Section Foot Section Foot Deck Deck Section Section Clamping Clamping Clamping Knobs Clamping Knobs they comeKnobs to stop onKnobs their retention brackets. Foot footboard bracket slidemechanism contacts its Bed BedExtension Extension Bed Bed Extension Extension Procedure Procedure Procedure Procedure mechanical stops. Knob fully clamped (knob fastener fully engaged) Knob Knob fully clamped not fully (knob clamped (knobKnob not fully clamped (knob fastener fully engaged) fastener not fully engaged) fastener not fully engaged) Unlock footbydeck extension 4. Unlock pan foot by grasping deck extension the pan by grasping the 3. Clamp the footboard bracket 3. Clampslide the mechanism footboard bracket by slide4.mechanism chrome and sliding chrome the locking handlemechanism and sliding the locking mechanism turning both retention knobs turning clockwise both retention until hand knobs tight. clockwise until handle hand tight. towards the patient left side towards of the thebed patient to the left side of the bed to the Knob Knob fully fully clamped clamped Knob Knob fully (knob (knob fully clamped clamped (knob (knob IMPORTANT: Ensure that IMPORTANT: the clamping Ensure knob fastener that thenot clamping knob fastener Knob Knob not not fully fully Knob clamped Knob clamped not fully (knob (knob fully clamped clamped (knob (knob unlocked unlocked unlocked position icon) (green, unlocked icon) fastener fastener fully fully engaged) fastener engaged) fastener fully fully engaged) engaged) extends through the retention extends hole through located the retention the hole located in theposition (green, fastener fastener notin not fully fastener fully fastener engaged) engaged) not not fully fully engaged) engaged) footboard bracket channel. footboard Typicalbracket both sides. channel. Typical both sides. 4.by 4. Unlock foot 4. foot 4. Unlock deck deck Unlock extension foot extension foot deck deck pan extension pan extension by by grasping grasping panpan by thethe by grasping grasping thethe 3.1-70-001-H 3. Clamp Clamp the 3. the footboard 3. Clamp footboard Clamp the bracket the footboard bracket footboard slide slide bracket mechanism bracket mechanism slide slide mechanism byby mechanism byUnlock User Manual - Spirit™ 1-70-001-H Bed User Manual - Spirit™ © Carroll Bed Hospital Group Inc. © Carroll Hospital Group Inc. Page 61 of 120 Page 61 of 120 chrome chrome handle handle chrome chrome and and handle sliding sliding handle the and the and locking sliding locking sliding mechanism the mechanism the locking locking mechanism mechanism turning turning both both turning retention turning retention both both knobs retention knobs retention clockwise clockwise knobs knobs until clockwise until clockwise hand hand tight. until tight. until hand hand tight. tight. towards towards thethe towards patient towards patient left the left the side patient side patient of of the left the left bed side bed side to ofto the the ofthe the bedbed to the to the IMPORTANT: IMPORTANT: IMPORTANT: IMPORTANT: Ensure Ensure that that Ensure thethe Ensure clamping clamping that that the knob the clamping knob clamping fastener fastener knob knob fastener fastener unlocked unlocked position position unlocked unlocked (green, (green, position position unlocked unlocked (green, (green, icon) icon) unlocked unlocked icon) icon) extends extends through through extends extends thethe through retention through retention the hole the retention hole retention located located hole inhole in the located the located in the in the footboard footboard bracket footboard bracket footboard channel. channel. bracket bracket Typical Typical channel. channel. both both Typical sides. Typical sides. both both sides. sides. Knob Knob unclamped unclamped and and Knob Knob unclamped unclamped andand Knob Knob clamped clamped Knob Knob clamped clamped 1-70-001-H 1-70-001-H User 1-70-001-H User Manual 1-70-001-H Manual - Spirit™ User - Spirit™ User Manual Bed Manual Bed-contacting Spirit™ - Spirit™ Bedretention Bed ©© Carroll Carroll Hospital Hospital © Carroll © Group Carroll Group Hospital Inc. Hospital Inc. Group Group Inc.Inc. retention bracket bracket retention retention bracket bracket contacting contacting contacting Page Page 61 61 of 120 of 120 Page Page 61 of 61120 of 120 1. 1. Elevate Elevate bed 1.bed 1. Elevate to Elevate to comfortable comfortable bed bed to comfortable to working comfortable working height. working working Unclamp Unclamp height. height. 2.Unclamp 2. Grasp Grasp footboard footboard 2. 2. Grasp Grasp bracket footboard bracket footboard byby the bracket the bracket corners corners by by the asas the shown corners shown corners as as shown shown 3.Clamp the footboard bracket slideheight. mechanism byUnclamp 4. Unlock foot deck extension pan by grasping thethe footboard footboard thebracket the footboard bracket footboard slide slide bracket mechanism bracket mechanism slide slide mechanism byby mechanism turning turning both byboth by turning turning both both above. above. Gently Gently above. and above. and smoothly Gently smoothly Gently and pull and smoothly pull away smoothly away from pull from pull the away the away head head from from thethe head head turning both retention knobs clockwise until hand tight. the chrome handle and sliding the locking knobs knobs counter-clockwise counter-clockwise knobs knobs counter-clockwise counter-clockwise until until they they come until come until to they to stop they stop come on come onto stop to stop onof onthe of the bed bed until ofuntil the ofthe the the bed footboard bed footboard until until thebracket the footboard bracket footboard slide slide bracket bracket slide slide their their retention retention their their brackets. retention brackets. retention brackets. brackets. mechanism mechanism mechanism contacts contacts mechanism itsits contacts mechanical mechanical contacts its its mechanical stops. stops. mechanical stops. stops. left side of the mechanism towards the patient IMPORTANT: Ensure that the clamping knob fastener bed to theunlocked position extends through the retention hole located in the (green, unlocked icon) footboard bracket channel. Typical both sides. SPIRIT™ USER MANUAL - VERSION 01-2013 Knob Knob fully fully clamped clamped Knob Knob fully (knob (knob fully clamped clamped (knob (knob Knob Knob notnot fully fully Knob clamped Knob clamped notnot fully (knob (knob fully clamped clamped (knob (knob fastener fastener fully fully engaged) fastener engaged) fastener fullyfully engaged) engaged) fastener fastener notnot fully fastener fully fastener engaged) engaged) notnot fullyfully engaged) engaged) PAGE 15/20 5. Grasp the chrome handle as shown at right. Gently 6. Lock foot deck extension pan by grasping the Grasp thechrome chrome handleas asshown shownatatright. right. Gently and 6.6.Lock graspingthe thechrome chrome Lockfoot footdeck deck extension panbybygrasping 5.5.Grasp the handle Gently and extension pan smoothly pull away from the head end of the bed until handle and sliding the locking mechanism towards and smoothly pull away from the head end of the bed chrome handle and sliding smoothly pull away from the head end of the bed until handle and sliding the locking mechanism towards the locking thefoot footdeck deckextension extensionpan pancontacts contactsitsitsmechanical mechanical patientright rightside sideofofthe thebed bedtotothe thelocked locked the the patient until the foot deck extension pan contacts its the (red, mechanism towards the patient right side of stops. position(red, lockedicon). icon). stops. position locked mechanical the bed to the locked pan position 5. 5. Grasp Grasp the thestops. chrome chrome handle handle as as shown shown at at right. right. Gently Gently and and 6. grasping the the chrome chrome 6. Lock Lock foot foot deck deck extension extension pan by by grasping (red, locked icon). smoothly smoothly pull pull away away from from the the head head end end of of the the bed bed until until handle handle and and sliding sliding the the locking locking mechanism mechanism towards towards WARNING WARNING the the foot foot deck deck extension extension pan pan contacts contacts its its mechanical mechanical the the patient patient right right side side of of the the bed bed to to the the locked locked stops. stops. PossiblePATIENT PATIENTENTRAPMENT ENTRAPMENTHazard Hazardcould couldoccur occurififthe themattress mattressisisnot notsecurely securely Possible position position (red, (red, locked locked icon). icon). located and retained on the mattress deck by the four corner mattress keepers. located and retained on the mattress deck by the four corner mattress keepers. WARNING NEVERperform performaabed bedextension/retraction extension/retraction withaapatient patienton onthe thebed. bed. NEVER with NEVER place a patient on the bed if the mattress is not properly located and retained on WARNING WARNING NEVER place a patient on the bed if the mattress is not properly located and retained on Possible PATIENT Hazard could themattress mattressENTRAPMENT deckby bythe thefour fourcorner corner mattresskeepers. keepers.occur if the mattress is not securely located the deck mattress Possible Possible PATIENT PATIENT ENTRAPMENT Hazard Hazard could occur occurkeepers. ifif the the mattress mattress isis not not securely securely and retained on the mattressENTRAPMENT deck by the four cornercould mattress NEVER perform a bed located located and and retained retained on on the the mattress mattress deck deck by by the the four four corner corner mattress mattress keepers. keepers. extension/retraction with a patient on theCAUTION bed. NEVER place a patient on the bed if the mattress CAUTION NEVER NEVER perform perform aa bed bed extension/retraction extension/retraction with with aaby patient patient on on“lock” the the bed. bed.mattress keepers. is not properly and retained on the mattress deck the four corner Possiblelocated UNEXPECTED MOTION could occur theslide slide lock not the “lock” Possible UNEXPECTED MOTION could occur ififthe lock isisnot ininthe positionand andthe themattress mattressdeck deckisisarticulated articulatedfrom thehorizontal horizontalposition. position. position NEVER NEVER place place aa patient patient on on the the bed bed ififfrom the thethe mattress mattress isis not not properly properly located located and and retained retained on on When the bed is in either the extended or retracted position, the clamping knob When the bed is in either the extended or retracted position, the clamping knob the the mattress mattress deck deck by by the the four four corner corner mattress mattress keepers. keepers. fastenersMUST MUSTbe befully fullyengaged engagedCAUTION andthe theslide slidelock lockMUST MUSTbe beininthe the“lock” “lock”position positionprior prior fasteners and placingaapatient patienton onthe thebed bedand/or and/orallowing allowingaapatient patienttotoreturn returntotothe thebed. bed. totoplacing Possible UNEXPECTED MOTION could occur if the slide lock is not in the “lock” position CAUTION CAUTION and the mattress deck is articulated from the horizontal position. When theand bed Bedretraction retraction procedure isthe thesame same asthe the above exceptthat that thefootboard footboard bracket and is in either the Bed procedure is as above except the bracket Possible Possible UNEXPECTED UNEXPECTED MOTION MOTION could could occur occur if if the the slide slide lock lock is is not not in in the the “lock” “lock”and the the foot deck extension pan are pushed towards the head end of the bed until contact extended or retracted position, the clamping knob fasteners MUST be fully engaged NOTE: the foot deck extension pan are pushed towards the head end of the bed until contact isis NOTE: position position and and the the mattress deck deckstops. isis articulated articulated from from the the horizontal horizontal position. position. made withbe their respective mechanical stops. with their mechanical slide lockmade MUST inrespective themattress “lock” position prior to placing a patient on the bed and/or allowing When the theto bed bed in in either either the the extended extended or or retracted retracted position, position, the the clamping clamping knob knob a patient When to return theisisbed. NOTE: fasteners fasteners MUST MUST be be fully fully engaged engaged and and the the slide slide lock lock MUST MUST be be in in the the “lock” “lock” position position prior prior to to placing placing aa patient patient on on the the bed bed and/or and/or allowing allowing aa patient patient to to return return to to the the bed. bed. Bed Bedisretraction retraction procedure isis the the same same as asthe the thefootboard above above except except that thatand the thethe footboard footboard bracket bracket and and Bed retraction procedure the same procedure as the above except that bracket foot deck extension the thethe foot foothead deck deckend extension extension pan are are pushed pushed towards the head head end of of the the bed bed until until contact contact isis NOTE: pan areNOTE: pushed towards of the pan bed until contacttowards is madethe with theirend respective mechanical stops. made made with with their their respective respective mechanical mechanical stops. stops. 1-70-001-HUser UserManual Manual- Spirit™ - Spirit™Bed Bed 1-70-001-H PAGE 16/20 1-70-001-H 1-70-001-H User User Manual Manual -- Spirit™ Spirit™ Bed Bed CarrollHospital HospitalGroup GroupInc. Inc. ©©Carroll Page6262ofof120 120 Page SPIRIT™ USER MANUAL - VERSION 01-2013 © © Carroll Carroll Hospital Hospital Group Group Inc. Inc. Page Page 62 62 of of 120 120 SPIRIT the low bed SPIRIT™ BED TROUBLESHOOTING GUIDE * NOTICE: Perform a brief function test on the bed. Check all functions on both the staff control pads and the patient control pads. PROBLEM / failure Recommended Action No functions working on the bed 1. Check to ensure bed is plugged in 2. Check wall outlet for power. 3. Check mains cable for any damage. Patients control pad working properly, Footboard staff control pad not working Check cable connection under lower left side of footboard. Footboard staff control pad is working properly, but quad-rail control pad not working Check lockout buttons on footboard pad; orange light on “lock” button prevents the patient control from being used. Bed will not lower all the way 1. Check to see if the ”Bed ” Up/Down function is locked out on the footboard 2. Check to see if the bed is in Trendelenburg or Reverse Trendelenburg angle. For patient safety bed maintains whatever angle is established by staff as the bed is raised and lowered - if the bed is in Trend/Reverse Trend it will not lower past its Trendelenburg limit of 15” deck height. If the bed is angled, level bed by pressing opposite ‘Trend’ function – bed will automatically stop at level position. Lift up footboard and check connection is not damaged. Hint: A slight Trendelenburg or Reverse Trendelenburg angle may not be easily visible. If the bed appears ‘stuck’ at approximately 15”, briefly press and hold the ‘Trend’ button to achieve a slight bed angle, then hold the ‘rev Trend’ button until the bed automatically stops at level. Then lower the bed. Bed “up” “down” Function not working To reset spirit ultra-low bed 1. Make sure that the bed is plugged in and switched on 2. Check that there are no lock-out lights showing on the footboard control panel 3. On the side rail control press the “BED DOWN” button and keep pressing for about 30 seconds or as long as it takes for the bed to go down to it’s lowest position 4. When the bed has gone down to it’s lowest position keep pressing for a further 30 seconds 5. The bed should now work normally SPIRIT™ USER MANUAL - VERSION 01-2013 PAGE 17/20 INFECTION CONTROL Spirit Ultra Low Bed quad side rails, headboard and footboard, have been treated to kill bacteria that come in contact with these bed surfaces. This treatment lasts throughout the life of the bed and is effective against numerous bacteria, including MRSA and e-coli. In addition, the detachable mattress deck provides easy and thorough cleaning of the entire surface, while the fiber-composite material reduces moisture build-up. CLEANING ADVICE • The SPIRT™ bed is manufactured to IPX4 : this is “moderate resistance to ingress of liquids and dust”. • The bed can be washed in a low-pressure spray booth. • All normal hospital cleaners can be used e.g. 1/10,000 chlorine • DO NOT USE PHENOL - BASED CLEANERS • ALWAYS DISCONNECT THE POWER BEFORE CLEANING If you require any further advice please call Montcalm International on 01865 409926. PAGE 18/20 SPIRIT™ USER MANUAL - VERSION 01-2013 SPIRIT the low bed SPECIFICATIONS • Sleep surface deck length 80” (2030mm) • Recommended weight capacity 35 stone / 227kgs • Sleep surface deck to floor - high position 34” (865mm) • Recommended mattress thickness 6” (152mm) • Sleep surface deck to floor - low position 8.25” (200mm) • Recommended mattress size 900mm x 2032mm • Overall sleep surface width (with mattress 36” (915mm) • Overall length 93.5” (2375mm) • Overall sleep surface width (without mattress) 35.5” (900mm)•Overall width (with quad rails) 40 “ (1020mm) FEATURES Low Bed HeightCentral Lock-and-Steer System • Prevents patient falls and related injuries • Colour coded foot pedal has three functions: • Help risk-free manual handling complete caster lockout, neutral/total swivel and steer mode (for single attendant bed transport). Detachable Mattress Deck Bed Exit Alarms (Optional) •Fibre composite deck completely detaches for • Alarm sounds in-patients room when patient gets thorough sanitization out of bed • Standard 5-year warranty Footboard Staff Control Panel Patient Controls and Lock-out • 15-function panel is located on the footboard •Can add optional 6-function electric Hand for staff access Pendant • Includes lockout buttons for each and all-patient • Patient access can be locked-out from (each or all) controls patient controls • Total bed lockout feature • Includes Trendelenburg, Reverse Trendelenburg, Chair Positioning, CPR, and Auto Contour functions •Head section and bed frame angle - monitor Moulded Quad Rails • Pass all new FDA guidelines for bedrail • Bed can be extended by 4” / 100mm entrapment IEC 60601-2-52 • Provide assistance, freedom and protection for patients SAFETY FEATURES • Ultra low height of 8.25”/200mm prevents • Built-in emergency battery back-up systems patient falls • Battery monitor • Passes all new 2006 FDA Bedrail Entrapment • Instant CPR release button Guidelines • Total bed lock-out feature • Easy-access to Central Lock-and-Steer pedal at • Bed Exit Alarm system (optional) head-end and foot-end • Removable headboard and footboard • Patient control positioning • Easy-to-read angle indicators for degree of Head • One-button chair positioning & Trendelenburg • Secure caster locking system • Ergonomically designed quad rails •Detachable mattress deck facilitates infection control • SPIRIT™ can be used with a wide range of mattresses and therapeutic support surfaces to meet the specific needs of your patient. (see recommended mattress dimensions above) SPIRIT™ USER MANUAL - VERSION 01-2013 PAGE 19/20 SPIRIT ULTRA-LOW BED the low bed specialist FEATURES The SPIRIT™ Ultra Low Bed FULLY MOBILE AT ANY HEIGHT FULL FOUR-WHEEL LOCK (ROTATION AND SWIVEL) USER MANUAL SEALED WATERPROOF ELECTRICS COMPOSITE “EASY-CLEAN” MATTRESS PLATFORM EMBEDDED PATIENT CONTROLS IN SIDE-RAILS INTERGRATED NURSE CALL BUTTON CENTRAL CONTROL PANEL ON FOOTBOARD SELECTIVE PATIENT CONTROL “LOCKOUT” COMPLETE SAFETY CONTROL “LOCKOUT” INSTANT CPR FULLY PROFILING MATTRESS PLATFORM AUTO-CONTOUR TRENDELENBURG POSITIONING AUTO CARDIAC CHAIR POSITION MOULDED HEADBOARD/FOOTBOARD WITH DROP-IN CONNECTION FOLD-DOWN QUAD-RAILS FOR PATIENT TRANSFER MEETS ALL FDA NON-ENTRAPMENT REQUIREMENTS REMOVABLE HEADBOARD AND FOOTBOARD BATTERY BACK-UP SPECIFICATION OVERALL LENGTH DECK LENGTH 230 CMS 200 CMS Guidance Notes for Safe Use 100 CMS OVERALL WIDTH DECK WIDTH DECK HEIGHT: MATTRESS DECK TO FLOOR LEVEL - LOW 20 CMS DECK HEIGHT: MATTRESS DECK TO FLOOR LEVEL - HIGH 85 CMS PATIENT WEIGHT CAPACITY 35 STONE 230 KGS CE Class 1 medical Device CE CLASS 1 MEDICAL DEVICE 1 Stert Street, Abingdon Oxfordshire OX14 3JF T 01865 409926 F 01865 409948 [email protected] www.montcalmcare.co.uk 89 CMS