Download U300/UD300 Series Ice Dispensers

U300/UD300 Series Ice Dispensers
Order parts online
www.follettice.com
Operation, Service and Parts Manual
Service Number A23719 to B22204
Single-sided dispensers
Model U300
Model U300B
Model U300R400A/W
Model U300BR400A/W
Model U300R800A/W
Model U300BR800A/W
Model UD300R400A/W
Model UD300R800A/W
Dual-sided dispensers
Model UD300
801 Church Lane • Easton, PA 18040, USA
Toll free (800) 523-9361 • (610) 252-7301
Fax (610) 250-0696 • www.follettice.com
208782R03
Welcome to Follett
Follett ice dispensers enjoy a well-deserved reputation for excellent performance, long-term reliability and
outstanding after-the-sale support. To ensure that this dispenser delivers that same degree of service, we ask that
you take a moment to review this manual before using the dispenser. Should you have any questions or require
technical help at any point, please call our technical service group at (800) 523-9361 or (610) 252-7301.
Before you begin
Check your paperwork to determine which model you have. Following is an explanation of the different model
numbers in the U300 series.
U300BR400A
Condenser type – A = air-cooled, W = water-cooled
Remote icemaker(s) capacity and refrigerant – 400 = 400 lbs (181kg)/day, R404A
800 = 800 lbs (363kg)/day, R404A
absence of = manual fill unit
B = integral beverage cooling. Absence of a B = no integral beverage cooling.
Approximate storage capacity in lbs
Configuration – U = undercounter single-sided, UD = undercounter dual-sided
!
Important cautions
• Storage area of dispenser contains mechanical, moving parts. Keep hands and arms clear of this
area at all times. If access to this area is required, power to unit must be disconnected first.
• Follett manual load units accommodate most cube/cubelet ices up to 1" square and Follett
compressed nugget ice. Crushed, flake, bagged or congealed ice cannot be used. Use of these ices
can jam dispenser and void warranty. Separate any “waffle-like” sections of cubes before adding to
dispenser. If you have questions concerning your ice type, call Follett’s customer service group at
(800) 523-9361 or or ( 610) 252-7301.
• Follett recommends use of an activated carbon filter for units equipped with icemakers.
• Ice is slippery. Maintain counters and floors around dispenser in a clean and ice-free condition.
• Ice is food. Follow cleaning instructions to maintain cleanliness of delivered ice.
2
Electrical Specifications – 115V, 60Hz, 1 phase
!
U300 series dispensers with remote icemaker(s) require separate circuit and
disconnect for each icemaker and dispenser.
Single-sided models
U300 – dispenser 6.0 amps
U300B – dispenser 7.0 amps
U300R400A/W – dispenser 6.0 amps, icemaker 11.0 amps
U300BR400A/W – dispenser 7.0 amps, icemaker 11.0 amps
U300R800A/W – dispenser 6.0 amps, icemakers 11.0 amps each
U300BR800A/W – dispenser 7.0 amps, icemakers 11.0 amps each
Dual-sided models
UD300 – dispenser 8.0 amps
UD300R400A/W – dispenser 8.0 amps, icemaker 11.0 amps
UD300R800A/W – dispenser 8.0 amps, icemakers 11.0 amps each
Note: Each icemaker and dispenser require separate circuit with electrical disconnect within
10 feet (6m). Equipment ground required. Standard electrical – 115V, 60 Hz, 1 phase. Max. fuse
dispenser – 15 amps; each icemaker – 20 amps.
!
On all models with remote icemaker(s), black wire on icemaker control board
LINE VAC terminal must be moved to 24V terminal.
Plumbing
!
Do not reduce size of drain lines or tie drains together.
Dispenser – all models
3/4" PVC slip fit bin drain
1" PVC slip fit drain pan drain(s)
1" PVC slip fit beverage bath drain (units with beverage cooling only)
Note: Drains must be hard piped and insulated. Maintain 1/4" per foot (6mm per 304mm) min. slope
Icemaker – automatic load models only
1/4" FPT water in
1/2" MPT drain
3/8" FPT condenser inlet (water-cooled condenser only)
1/2" FPT condenser drain (water-cooled condenser only)
Note: Water disconnect within 10 feet (3m) of icemaker(s) is required for automatic load units
3
U300 series single-sided dispensers
Required clearances:
• 60" (1524mm) for installation
• 49" (1245mm) for auger removal
Front view
Dispenser only
with no icemaker
Model U300/U300B
40.875"
(1039mm)
One icemaker –
Models U300R5A/W
U300BR5A/W
Entrance
Two icemakers –
beverage
Models U300R10A/W
lines
U300BR10A/W
18.875"
(480mm)
ICE
25.25"
(642mm)
54.875"
(1394mm)
12" min
(305mm)
29.625"
(753mm)
Electric
conn.
17"
(432mm)
Disp.
drains
6" min
(153mm)
Side view – ice dispense chute
Ice waterbath
(U300BR5A/W,
U300BR10A/W
only)
32.375"
22" (823mm)
(559mm)
Beverage
lines enter
through
bottom
Junction
boxes
Ice
transport
tube entry
8.5"
(216mm)
1"
drains
7"
(178mm)
3" (77mm)
3/4"
drain
10"
(254mm)
9"
2.5" (229mm)
(64mm)
9"
(229mm)
15"
(381mm)
30"
(762mm)
4
27.5"
(699mm)
2"
(51mm)
UD300 series dual-sided dispensers
Required clearances:
• 60" (1524mm) for installation
• 49" (1245mm) for auger removal
Front view
43.875"
(1115mm)
Dispenser only with no
icemaker
Model UD300
ICE
25.25"
(642mm)
Dispenser with one icemaker
Models UD300R5A/W
Dispenser with two icemakers
Models UD300R10A/W
18.875" 12" min.
(480mm)
(305mm)
17"
(432mm)
Beverage
lines exit
through
bottom of
chase
Disp.
drains
54.875"
(1394mm)
12" min.
(305mm)
29.625"
(753mm)
Electric
conn.
6" min.
(153mm)
Side view opposite ice dispense chute
Side view - ice dispense chute
32.375"
(823mm)
12.125"
(308mm)
beverage
lines exit
through
bottom of
chase
ice
tube
entry
8.5"
(216mm)
27.5"
(699mm)
2.5"
(64mm)
1"
drains
3/4"
drain
9"
(229mm)
8.5"
(216mm)
alt. ice
transport
tube entry
27.5"
(699mm)
2"
(51mm)
electric
conn.
10"
(254mm)
9"
(229mm)
15"
(381mm)
13.25"
(337mm)
30"
(762mm)
5
13.25"
(337mm)
To start up and operate dispenser
1. Follow all cleaning and start-up instructions in U300 Installation Manual packed with dispenser before
operating dispenser.
2. Turn power switches located under dispenser top to ON position.
3. For manual load models, remove drain pan and fill storage area with compatible ice. (See caution on page 2
of this manual concerning ices which may be used in this dispenser.)
4. For automatic fill models, turn icemaker (bin signal) switch(es) located inside dispenser top to ON position
and begin to make ice.
5. When dispenser has at least 6" (153mm) of ice in storage area, press lever or button to ensure that dispenser
is operating properly.
How dispenser works
Follett’s single-sided U300 series and dual-sided UD300 series ice dispensers are available in manual load
configurations (using ice from another source) or automatic load configurations (fed from one or two Follett 400 lb/
day remote icemakers). An ice water bath beverage cooling system located directly behind valves is available for
single-sided U300 series dispensers. Dual-sided units must use a separate mechanical cooling system to cool
beverage lines.
In all models, ice is stored below counter in dispenser storage area. When dispense lever or button is pushed,
dispense motor is activated. This causes wheel assembly in storage area to rotate counterclockwise, moving ice to
vertical auger assembly. Vertical auger carries ice up to dispense chute where it drops by gravity into container.
In automatic load models, ice is manufactured in either one or two Follett remote icemakers. These icemakers
may be located up to 20 ft (3m) away from dispenser. As water freezes to inside walls of icemaker evaporator, a
rotating stainless steel auger removes ice and carries it to top of evaporator assembly where it is compressed and
extruded through an outlet port. The extruded ice is then pushed through tube to storage compartment of
dispenser. A bin thermostat shuts off icemaker when storage compartment is full.
Periodic cleaning of dispenser
!
Do NOT run plastic parts (drain pan, dispense chute cover, dispense wheel) through
a dishwasher.
Solution A: Prepare cleaning solution (200 ppm available chlorine content) of Ecolab Mikro-chlor Cleaner or equal chlorinated detergent. Solution temperature must be at 75˚ – 125˚F (23˚ – 52˚C).
Solution B: Prepare sanitizing solution (50 ppm available chlorine content) of Ecolab Mikro-chlor Cleaner or
equal chlorinated detergent. Solution temperature must be at 75˚ – 125˚F (23˚ – 52˚C).
Recommended daily cleaning of drain pan
1. Remove all debris from drain pan.
2. Pour 1 gallon (4L) hot water into drain pan to keep drain lines clear.
Recommended weekly cleaning
1. Remove drain pan(s) and grille(s) and wash with Solution A above. Rinse thoroughly.
2. On units with beverage valves, remove nozzles and diffusers from valves, soak for at least 10 minutes in
cleaning Solution A, rinse, sanitize with Solution B and reinstall.
3. Pour a solution of one cup (8 oz/237ml) household bleach mixed with one gallon (3.8L) hot water into drain
pan(s) to help prevent algae growth in drain lines.
Recommended quarterly cleaning (every 3 months)
1. Empty all ice from dispenser.
2. Remove dispenser top and turn bin signal switch(es) and dispenser power switch to OFF position.
3. Remove dispenser drain pan(s) and grille(s).
4. Remove thumbscrews from splash panel, lift up and out at bottom of panel and remove.
5. Remove chute cover(s), dispense chute(s), auger tube and auger (see disassembly instructions).
6
6. Remove yoke rods, drive shaft and dispense wheel (see disassembly instructions).
7. Clean all components and bin storage area with Solution A, rinse thoroughly with clear water and sanitize
with Solution B. Caution: To avoid damage to switch, do not immerse chute cover in solution. Wipe only
with cleaning cloth.
8. On units with beverage valves, remove nozzles and diffusers from valves, soak for at least 10 minutes in
cleaning Solution A, rinse, sanitize with Solution B and reinstall.
9. For models with integral ice water bath beverage cooling only:
a. Lower Tygon drain tube found on drain connection side of waterbath into PVC waterbath drain and drain
ice water bath.
b. Wash bath interior and components with Solution A, using a bottle brush to clean coils.
c. Reposition Tygon waterbath drain line in UP position.
d. Fill waterbath with Solution A and turn power back on.
e. Allow pump to run for 2 minutes to clean pump and pump lines.
f. Turn power OFF, drain bath and secure tube in UP position.
Putting unit back in service after quarterly cleaning
1. On units with integral beverage cooling, fill ice water bath manually with potable water. Add ice slowly enough
to avoid spillage over top of waterbath.
2. Reassemble components.
3. For manual load units, turn dispenser power switch to ON position and fill unit with approved ice (see caution
statement page 2).
4. For automatic load units, turn bin signal switch(es) and dispenser power switch to ON position and allow
storage area to fill.
5. When dispenser has at least 6" (153mm) of ice in lower storage area, press dispense button or lever to test
that dispenser is functioning properly.
Quarterly cleaning of icemaker system
!
Units with an icemaker require that icemaker be cleaned at least every three months or
more often if local water conditions dictate. Failure to clean icemaker system will result
in decreased performance and potential damage to icemaker. Refer to Icemaker
Operation and Service Manual for instructions.
Disassembly instructions for periodic cleaning
Dispense chute cover removal
1. Remove dispenser top cover and turn three switches on electrical box OFF.
2. Remove two Phillips head screws from top of black dispense chute cover.
3. Pull chute cover forward and down to remove.
4. On push-button actuated units, disconnect plug on harness.
dispenser top cover
(electrical box below)
dispense chute cover
(dispense mechanism
behind cover)
splash
panel
dispense tower
(auger and
auger tube
inside)
drain
pan
Front view
7
Gate assembly removal
1. Remove black dispense chute cover.
2. Remove thumbscrews on each side of focus chute
and remove.
3. Remove quick release pins holding dispense gate
assembly and chute.
4. Lift gate up and over hinge tabs, then carefully pull and
tilt to unhook from solenoid link.
5. Pull ice chute toward you to unclip from dimples on
chute mounting bracket.
6. Pull ice chute and gate toward you and out through
panel opening.
Dispense chute assembly
quick release pins
gate assembly
gate assembly
springs
Auger and auger tube removal
1. Remove black dispense chute cover, focus chute,
dispense chute and gate assembly.
2. Remove drain pan.
3. Remove thumbscrews from splash guard and remove.
4. Remove thumbscrews from splash panel; lift and pull
forward at base of panel and remove.
5. Unplug auger motor at electrical box.
6. Remove two 1/4-20 bolts holding auger motor to
holddown bracket.
7. Remove two thumbscrews from auger motor stabilizer
bracket and aside.
8. Lift auger motor off.
9. Remove dispense chute mounting bracket assembly.
10. Remove side panel of tower.
11. Remove screw holding top auger tube ring to lower ring.
12. Lift auger out of auger tube.
13. Lift out auger tube, turning as needed to clear rivnuts
on side auger motor mounting bracket.
ice chute
mounting
bracket
ice chute
U300 cutaway – front view
auger motor
auger tube
wheel motor
auger
tube ring
auger
Dispenser wheel removal
1. Remove dispenser top and turn power
switch OFF.
2. Remove drain pan and ice bin access
cover below it.
3. Remove splash guard and wheel motor access cover.
4. Remove all ice from bin.
5. Unplug wheel motor at electrical box and remove
ground wire.
5. Remove wheel motor by pulling out two quick
release pins.
6. Lift drive shaft up through hole in countertop.
7. Lift dispense wheel out through drain pan opening.
fixed yoke
rods with
brackets (front
rod is lowest)
8
drive
shaft
Front
fixed ramped
yoke rod with
bracket (below
rotating drive
bar)
Wiring diagram
Single-sided models with a service number of 5012607 or higher or any model with
blue circuit board
JUNCTION BOX
CONTROL BOARD
PL9
BLACK
POWER
SWITCH
PL13
PUMP QC9
GREEN
QC1
WM QC10
BLACK
PL13
GREEN
AM QC11
PL9
BLACK
PL1
BLACK
PL1
WM
PL2
BLACK
PL2
AM
QC3
L2
AM . . . . . AUGER MOTOR
DISP . . . DISPENSE
GND . . . . GROUND
IM . . . . . . ICE MAKER
JB . . . . . .JUNCTION BOX
PB . . . . . .PUSH BUTTON
PL . . . . . .PLUG
QC . . . . . QUICK CONNECT
SOL . . . . SOLENOID
TRAN . . .TRANSFORMER
T'STAT . .THERMOSTAT
WM . . . . .WHEEL MOTOR
WHITE
WHITE
QC5
L1
LEGEND
PL13
PUMP
QC4
QC2
L2
WHITE
INPUT POWER
BLACK
GREEN
GND L1
JUNCTION BOX
WHITE
QC6
WHITE
QC7
QC8
TRANSFORMER
PRIMARY
BLACK
WHITE
BLUE
Temperature lights
RED
SECONDARY (24V)
TRAN
BLUE
PL12
PL12
CONTROL BOARD
BLUE
QC21
RED
QC22
24 VAC
24 VAC
DRAIN PAN
SWITCH
QC18
TRAN
RED
QC17
TRAN
BATH
BATH
SENSOR
PL3
YELLOW
BLUE
RED
DISPENSE
PL3
SWITCH
(PB OR LEVER)
BLUE
BATH
SOL
SOL
PL6
Low LED: Bath is at
optimal temperature for
cold drinks.
RED
QC14
DISP
SWITCH
PL6
DISPENSE
BLUE
QC15
DISP
SOL
SOL
High LED: Bath
temperature is above
optimal temperature. The
bath will fill with ice for 15
seconds and will then
stop for 75 seconds. If
temperature is still too
high, cycle will repeat.
PL4
RED
PL4
DRAIN PAN
SWITCH
TRAN
BEVERAGE VALVES
BLUE
PL10
QC
QC
KEY
SWITCH
V
ACCESSORY
V
V
V
V
V
V
V
V
V
RED
PL10
BLUE
PL14
BIN SIGNAL
SWITCH IM#1
YELLOW
BLUE
BLUE
PL14
PL7
BLUE
TRAN
T'STAT
1 2
BLUE
BIN SIGNAL
SWITCH IM#2
PL8
YELLOW
24V JB
BLUE
TRAN
24V JB
IM#1
BIN
SIGNAL
IM#1
BIN
SIGNAL
9
Temperature lights
provide information on
the status of the icewaterbath. When lighted,
the following LEDs
indicate:
BLUE
PL7
PL8
RED
RED
QC22
QC17
Error and Low LEDs:
After 15 minutes of fill
cycling, bath is above
40˚F (4.4˚C).
Error (flashing) LED:
Board not receiving
signal from sensor.
Wiring diagram – all dual-sided models
GND
JUNCTION BOX
JUNCTION BOX
L1
L2
INPUT POWER
PL13
WHITE
PL13
BLK RED
BLK BLK
WHT WHT WHITE
BLK
BLK
WM
TB
SAFETY SAFETY
PL1
PL1
PL12
PL12
R1
SWITCH SWITCH
4 7
#2
#1
(DP-NO) (DP-NO)
PL13
BL
K
POWER
SWITCH
K
BLK
BL
GREEN
BLK
TB
BLK BLK
4
7
BLK
GREEN
BLACK
TB
R1
(6)
YELLOW
BLUE
BIN
STAT
(1)
TRANS.1
(R)
BLUE A
PL4
R1
RED
TRANS.1
(C)
R1
(B)
PL4
SODA VALVES – SIDE 1
BLACK
SAFETY
QC
V V V V V V V V V V
PL10
SWITCH #1
RED
(DP-NO)
ACCESSORY
PL10
24V J.B.
IM #1 YEL
BLUE 1
BLUE
BLUE
RED
RED
YEL
2
BIN
BIN SIGNAL
SIGNAL
PL7
PL7
QC
T-STAT
SWITCH IM#1
24V J.B.
BLUE
BLK
QC
KEY
SWITCH
BLUE
BLUE
YELLOW
DISPENSE
SWITCH #2
(PB OR LEVER)
PL5
6
PL11
KEY
SWITCH
#2
S
PL6
TB
R2
RED
B
TRANS.2
(C)
R2
(B)
RED
PL6
SODA VALVES – SIDE 2
BLK
QC
BLUE A
DISPENSE
SOLENOID #2
BLUE
R2
WHITE
PL5
9
BLUE
BLUE
SEC
24V
YELLOW
TRANS.1
(C)
C
R
BLUE
TRANS.1
(C)
IM #2 BLUE
RED
BIN
PL8
SIGNAL
BIN SIGNAL
PL8
SWITCH IM#2
TRANSFORMER 2
PRI
BLACK
TRANS.2
(R)
RED
B
S
TB
TRANS.2
(R)
R1
DISPENSE
SOLENOID #1
BLUE
BLUE
R2
(6)
TB
PL3
9
BLUE
TRANS.1
(R)
SEC
24V
YELLOW
6
WHITE
C
R
DISPENSE
SWITCH #1
(PB OR LEVER)
PL3
WHT
PL2
PL2
R2
TRANSFORMER 1
PRI
AM BLUE
QC
BLACK
SAFETY
V V V V V V V V V V
SWITCH #2
(DP-NO)
RED
PL11
ACCESSORY
10
TRANS.2
(C)
Service and parts
Before calling for service
1. Check that ice is in the dispenser and that congealed cubes are not causing a jam.
2. Check that circuit breaker and switches are in ON position.
3. Check that drain pan(s) are on securely. If ajar, neither dispenser nor valves will operate.
4. Check that all drains are clear.
For units equipped with Follett compressed nugget icemaker, see Icemaker Operation and Service Manual for
service and troubleshooting information.
Dispenser troubleshooting guide
Possible cause
Symptom
Ice does not dispense when switch
is actuated.
• Auger motor does not run
• Wheel motor does not run
• Gate does not open
1.Power switch faulty or in OFF position;
loose connection.
2.Faulty dispense switch.
3.Faulty transformer/tripped breaker.
4.Faulty fill board.
5.Drain pan ajar.
6.Faulty drain pan safety switch.
Solution
1.Turn power switch to ON, check
connections.
2.Replace switch.
3.Replace transformer/reset
breaker.
4.Replace fill board.
5.Check pan and reseat.
6.Replace switch.
Ice does not dispense.
• Auger motor runs
• Wheel motor runs
• Gate does not open
1.Loose electrical connection.
2.Linkage problem between solenoid
and gate.
3.Faulty solenoid.
4.Faulty fill board.
Ice does not dispense.
• Auger motor does not run
• Wheel motor runs
1.Loose electrical connection.
2.Faulty auger motor.
3.Faulty run capacitor.
1.Check connections.
2.Check auger motor.
3.Check run capacitor.
Ice does not dispense.
• Auger motor runs
• Wheel motor does not run
1.Loose electrical connection.
2.Faulty wheel motor.
3.Faulty run capacitor.
1.Check connections.
2.Check wheel motor.
3.Check capacitor.
Warm drinks or soda foaming.
1.Fill storage area with ice or
check icemaker operation. Push
reset on board.
2.Check that ice-waterbath drain
tube is in fixed upright position.
Push reset on board.
3.Check pump. Push reset on
board.
4.Replace bath solenoid. Push reset
on board.
5.Replace thermistor.
1.No ice in storage bin.
2.Water drained out of ice-waterbath.
3.Faulty circulating pump.
4.Faulty bath solenoid.
5.Faulty thermistor.
1.Check connections.
2.Check linkage.
3.Replace solenoid.
4.Replace fill board.
If problem persists after following this basic troubleshooting guide, call Follett's
technical service department at (800) 523-9361 or (610) 252-7301.
11
Possible cause
Symptom
Beverage valves not operating.
Ice dispenses without actuation. No ice in dispenser.
Solution
1.Faulty 24V transformer.
1.Check transformer & circuit
2.Power switch faulty or in OFF position.
breaker.
3.Drain pan switch faulty or not depressed. 2.Check power switch.
4.Beverage key switch locking out access. 3.Check switch and placement of
drain pan.
4.Check valve lockout.
1.Front ice gate stuck open.
2.Faulty rear solenoid.
1.Adjust gate (contact Follett)
3.Faulty pump/faulty bath temperature
2.Replace solenoid.
sensor.
3.Replace pump or bath sensor.
4.Linkage pin dislodged or broken.
4.Check pin and reseat or replace if
5.Ice jam in rear chute.
broken.
6.Misplaced bath sensor causing jam of
5.Clear ice jam from chute.
rear chute.
6.Remount bath sensor in proper
7.Wire off rear solenoid causing ice to
location.
dispense out front when filling bath,
7.Reconnect wire.
without actuation.
1.Power switch in OFF position or faulty.
2.Bin signal switches in OFF position or
faulty.
3.Faulty bin thermostat.
4.Faulty transformer.
5.Icemaker related problem.
6.Faulty or disconnected wiring.
1.Check switch and replace if
necessary.
2.Check switch and replace if
necessary.
3.Replace bin thermostat.
4.Replace transformer.
5.Refer to icemaker Operation and
Service Manual for diagnosing.
6.Check for power and bin signal on
icemaker pc board.
Disassembly instructions for service requirements only –
NOT required for any cleaning procedure.
Ice water bath pump motor removal
Plan view ice water bath
1. Disconnect electrical wires to pump.
2. Remove two screws anchoring pump motor bracket
to water bath.
3. Loosen hose clamp on 1" (26mm) Tygon hose at pump
and pull hose free of pump motor.
4. Slide motor and bracket toward center of dispenser
and lift to remove.
12
drain
hose
bath sensor
pump
Parts
3
1
2
3
9
4
ICE
11
ICE
5
11
7
6
10
Single-side dispenser
11
7
6
10
Dual-side dispenser
1
9
7
8
Reference #
1
2
3
4
5
Not shown
6
7
Not shown
8
9
Not shown
10
11
Not shown
Not shown
Not shown
Not shown
Not shown
Not shown
Not shown
Not shown
Not shown
Not shown
Not shown
Not shown
Plan view
Description
Lid, with graphics, single-sided Lid, with graphics, dual-sided Graphics, “Follett”
Access panel, tower, single-sided
Access panel, tower, dual-sided
Cover, ice opening (below drain pan)
Drain pan assembly and grille
Drain pan, plastic
Switch, drain pan safety
Grille, drain pan
Chute cover, dispense, push-button with switch
Chute cover, dispense, lever
Splash guard
Thumbscrew, 10/32-1/2, splash guard
Switch, dispense, PB Switch, dispense lever (includes boot and spacer)
Boot, dispense switch button, lever
Access cover, wheel motor (behind splash guard)
Skid
Carton and fillers
Lip kit (plastic strip bordering ice bin opening and adhesive)
Insulation, transport tube (sold by the foot)
Tube, ice transport, 10 ft
Tube, ice transport, 20 ft
Plug 2 lead, male
Plug 2 lead, female
13
Part #
501930
501931
501938
501944
501945
501934
501935
501936
501318
501937
501957
501956
501943
501100
502441
501714
501841
501932
501946
501947
502285
501176
502522
502523
502333
502334
1
4
2
3
8
4
15
Top view
lower ring
Top view
auger tube seal
16
reinforcing
tab
9
5
6
5
12
10
6
11
13
7
14
Reference #
1
2
Not shown
Not shown
Not shown
3
4
5
6
7
8
9
Not shown
Not shown
Not shown
10
11
12
13
Not shown
Not shown
Not shown
Not shown
14
15
Not shown
Not shown
16
Front view
auger tube
countertop
section
Description
Motor, auger (includes capacitor), 100 RPM*
*Note: If your machine serial number precedes C69443, then you
Bracket, auger motor hold-down
Bracket, auger motor stabilizer, single-sided models
Bracket, auger motor stabilizer, dual-sided models
Seal, shaft, auger motor
Auger
Auger tube (includes insulation)
Insulation, auger tube
Ring, auger tube, upper
Ring, auger tube, lower
Motor, wheel, Brother (includes capacitor)
Bracket, wheel motor
Capacitor, wheel motor, Brother
Gasket, wheel motor bracket
Pin, quick release, wheel motor (2 required)
Drive shaft assembly, for Brother motor Agitator rods, fixed, front and back Wheel, dispense
Bearing plate, bottom auger
Bearing, bottom, auger
Agitator rod, ramped
Bracket, fixed agitator (3 used per unit)
Thumbscrew, 10/32 x 3/4, fixed agitator bracket (2 required)
Tee, drain
Thermostat box (includes 500514)
Thermostat
Retainer, ice hose (includes 2 thumbscrews)
Bracket, ice hose and wheel motor
14
Part #
00918904
502047
502060
502113
501977
501980
502631
502099
501939
502155
502657
501981
502658
501982
502102
502630
502629
501978
501971
501972
502628
501974
501259
502059
502211
500514
501764
502050
1
U300 dispense assembly
side view
U300 dispense assembly
top view
2
3
1
3
7
4
6
Reference #
1
2
3
4
5
Not shown
6
7
Not shown
Not shown
4
Description
Gate, dispense
Linkage pin, gate/solenoid
Pin, quick release, 3" (77mm), gate and lever
Chute, ice
Solenoid
Boot, solenoid
Dispense mechanism assembly
Spring, dispense mechanism (1 per side)
Chute, focus
Lever, dispense
5
Part #
501955
502096
501949
501952
501961
502098
501948
501950
501954
501953
5
4
6
3
2
1
Reference #
1
2
3
4
5
6
Not shown
Not shown
Not shown
Not shown
Not shown
Description
Manifold, carbonated water (bev. cooled units)
Syrup coil
Waterbath ice guide assembly
Bath sensor
Bracket, bath sensor
Pump, waterbath
Manifold, carbonated water (single-side, non-beverage cooled units)
Tubing, vinyl, 1/2" (13mm) ID x 5/8" (17mm) OD (order by the
foot – 5 feet required for bath, 2 feet required for overflow)
Tubing, vinyl, pump (order by the foot – 3 feet required)
Syrup tube, insulated, non-bev. cooled units)
Cap, carbonated water manifold valve fitting
15
Part #
502002
501962
502001
502208
502210
501964
501968
501965
501966
501967
502062
Electrical box
Single-sided models with Blue circuit board
3
2
1
POWER
RESET
5
4
Reference #
1
2
3
4
5
Not shown
Not shown
Not shown
Not shown
Description
Control board (blue)
Stand-off
Transformer, 65VA
Switch, rocker
Control box (includes all components)
Keylock switch with leads
Bracket, electric box support
Thermostat (located behind splash panel in thermostat box)
Key, beverage, lock switch
Part #
502207
501959
502058
502209
502212
501960
501933
500514
501286
Electrical box
All UD300 dual-sided models
1
2
3
Reference #
1
2
3
4
5
Not shown
Not shown
Not shown
4
5
Description
Relay, 24V
Transformer, 65VA
Control box, dual-side models
Thermostat
Switch, rocker
Bracket, electric box support
Keylock switch with leads
Key, beverage, lock switch
801 Church Lane • Easton, PA 18040, USA
Toll free (800) 523-9361 • (610) 252-7301
Fax (610) 250-0696 • www.follettice.com
Part #
501826
502058
502049
500514
502209
502113
501960
501286
208782R03
03/10