Download SERVICE MANUAL - MiniDisc Community Page

ZS-M30
SERVICE MANUAL
AEP Model
UK Model
Australian Model
Ver 1.1 2001.04
US and foreign patents licensed from Dolby
Laboratories Licensing Corporation
Model Name Using Similar Mechanism
CD
Section CD Mechanism Type
Optical Pick-up Name
NEW
Model Name Using Similar Mechanism
NEW
MD
MD Mechanism Type
Section
Optical Pick-up Name
KSM-213CDP
KSS-213C
MT-ZSM30-168
KMS-260B
SPECIFICATIONS
CD player section
System
Compact disc digital audio system
Laser diode properties
Material: GaAlAs
Wave length: 785 nm
Emission duration: Continuous
Laser output: Less than 44.6 µW
(This output is the value measured at a distance of about 200 mm
from the objective lens surface on the optical pick-up block with 7
mm aperture.)
Spindle speed
200 r/min (rpm) to 500 r/min (rpm) (CLV)
Number of programme positions
2
Frequency response
20 - 20 000 Hz +1/–2 dB
Wow and flutter
Below measurable limit
Radio section
Frequency range
FM: 87.5 - 108 MHz
MW:531 - 1,602 kHz (9 kHz step)
530 - 1,610 kHz (10 kHz step)
LW: 153 - 279 kHz
IF FM: 10.7 MHz
MW/LW: 450 kHz
Aerials
FM: Telescopic aerial
MW/LW: External aerial terminals
MD player section
System
Minidisc digital audio system
Disc
MiniDisc
Laser diode properties
Material: GaAlAs
Wave length: 785 nm
Emission duration: Continuous
Laser output: Less than 44.6 µW
(This output is the value measured at a distance of about 200 mm
from the objective lens surface on the optical pick-up block with 7
mm aperture.)
Recording/playback time
Stereo recording:
Maximum 80 minutes (with MDW-80)
Monaural recording:
Maximum 160 minutes (with MDW-80)
Revolutions
400 rpm to 900 rpm (CLV)
Error correction
Advanced Cross Interleave Reed Solomon Code (ACIRC)
Sampling frequency
44.1 kHz
Coding
Adaptive Transform Acoustic Coding (ATRAC)
9-873-011-12
Sony Corporation
2001D0200-1
© 2001.4
Personal Audio Company
Shinagawa Tec Service Manual Production Group
PERSONAL MINIDISC SYSTEM
ZS-M30
Modulation system
EFM (Eight-to-Fourteen Modulation)
Number of programme positions
2 stereo programme positions
Frequency response
20 - 20,000 Hz +1/–2 dB
Signal-to-noise ratio
Over 80 dB (during playback)
Wow and flutter
Below measurable limit
Power requirements
For personal minidisc system:
230 V AC, 50 Hz
For back-up memory:
4.5 V DC, 3 R6 (size AA) batteries
For remote control:
3 V DC, 2 R6 (size AA) batteries
Power consumption
26 W
Dimensions (incl.projecting parts)
approx. 475 X 165.5 X 249 mm (w/h/d)
(18 3/4 X 6 5 ⁄8 X 9 7/8 inches )
Mass
approx. 4.6 kg (10 lb. 2 oz)
Supplied accessories
Mains lead (1)
Remote control (1)
MW/LW loop aerial (1)
AV connecting cord (1)
Audio connecting cord (1)
General
Speaker
Full-range: 8 cm (3 1 ⁄4 in.) dia., 4 Ω cone type (2)
Panorama sound: 5 cm (2 in.) dia., 12 Ω cone type (2)
Inputs
LINE IN (stereo minijack): Sensitivity 436 mV/870 mV
Outputs
Headphones jack (stereo minijack) (1):
For 32 Ωimpedance headphones
Maximum power output
Full-range: 8 W
Panorama sound: 3.4 W
Design and specifications are subject to change without
notice.
TABLE OF CONTENTS
Specifications ........................................................................... 1
5. ELECTRICAL ADJUSTMENT
1. SERVICING NOTE
5-1. Tuner Section ................................................................... 17
5-2. MD section ....................................................................... 19
5-3. CD section ........................................................................ 25
1-1. Notes on Handling the Optical Pick-up Block or
Base Unit ............................................................................
1-2. Notes on Laser Diode Emission Check ..............................
1-3. Notes on Chip Component Replacement ...........................
1-4. Flexible Circuit Board Repairing .......................................
1-5. Chuck Plate Jig on Repairing .............................................
1-6. Checking the Laser Diode and Focus Search Operation ....
1-7. Checks Prior to Parts Replacement and Adjustments
(for MD Section) ...............................................................
3
3
3
3
3
3
4
2. GENERAL
Playing a CD ......................................................................
Recording a Whole CD (Synchronized Recording) ...........
Playing an MD ...................................................................
Listening to the Radio ........................................................
5
5
6
6
3. DISASSEMBLY
3-1. Cabinet (Rear), Cabinet (Front) ......................................... 7
3-2. BATT (B) Board, BATT (A) Board, Power Board ............. 7
3-3. Cabinet (Upper) ASSY ....................................................... 8
3-4. Main Board, LCD Board .................................................... 8
3-5. CD Board ........................................................................... 9
3-6. Top Board ........................................................................... 9
3-7. Tuner Board ........................................................................ 9
3-8. MD Block ASSY .............................................................. 10
3-9. SW (L) Board, Jack Board, SW (R) Board ...................... 10
3-10. MD Board ...................................................................... 11
3-11. REC Board, DETECT Board ......................................... 11
3-12. Over Write Head (HR901), MD Optical Pick-up,
D SW Board ................................................................... 12
4. TEST MODE
4-1. MD Section ......................................................................
4-2. Section the Test Mode ......................................................
4-3. Releasing the Test Mode ..................................................
4-4. Basic Operations of the Test Mode ..................................
4-5. Selecting the Test Mode ...................................................
4-6. Functions of Other Buttons ..............................................
4-7. Test Mode Displays ..........................................................
4-8. Meanings of Other Displays .............................................
2
6. DIAGRAMS
6-1. IC Pin Function Descriptions ...........................................
6-2. Block Diagrams (1/4) .......................................................
6-3. Block Diagrams (2/4) .......................................................
6-4. Block Diagrams (3/4) .......................................................
6-5. Block Diagrams (4/4) .......................................................
6-6. Printed Wiring Boards -Main Section- .............................
6-7. Schematic Diagram -Main Section (1/3)- ........................
6-8. Schematic Diagram -Main Section (2/3)- ........................
6-9. Schematic Diagram -Main Section (3/3)- ........................
6-10. Printed Wiring Boards -Power Section- .........................
6-11. Printed Wiring Boards -Tuner Section- ..........................
6-12. Schematic Diagram -Tuner Section- ..............................
6-13. Printed Wiring Boards -Control Section- .......................
6-14. Schematic Diagram -Control Section- ...........................
6-15. Printed Wiring Boards -CD Section- ..............................
6-16. Schematic Diagram -CD Section- ..................................
6-17. Printed Wiring Boards -MD Section- .............................
6-18. Schematic Diagram -MD Section (1/2)- ........................
6-19. Schematic Diagram -MD Section (2/2)- ........................
28
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
7. EXPLODED VIEWS
7-1. Rear Cabinet Section ........................................................
7-2. Front Cabinet Section .......................................................
7-3. Upper Cabinet Section .....................................................
7-4. Optical Pick-up Section ....................................................
7-5. MD Section -1 ..................................................................
7-6. MD Section -2 ..................................................................
64
65
66
67
68
69
8. ELECTRICAL PARTS LIST .................................... 70
13
13
13
13
14
16
16
16
SECTION 1
SERVICE NOTE
This Compact Disc player
is classified as a CLASS 1
LASER product.
The CLASS 1 LASER
PRODUCT label is located
on the bottom exterior.
ZS-M30
1-5. CHUCK PLATE JIG ON REPAIRING
On repairing CD section, playing a disc without the CD lid, use
Chuck Plate Jig.
• Code number of Chuck Plate Jig: X-4918-255-1
CAUTION
Use of controls or adjustments or performance of proceduresother than those specified herein may result in hazardous radiation exposure.
1-1. NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated
by the charged electrostatic load, etc. on clothing and the human
body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled
with care.
1-2. NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused
on the disc reflective surface by the objective lens in the optical
pick-up block. Therefore, when checking the laser diode emission,observe from more than 30 cm away from the objectivelens.
1-3. NOTES ON CHIP COMPONENT REPLACEMENT
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be damaged by heat.
1-6. CHECKING THE LASER DIODE AND FOCUS
SEARCH OPERATION
1. Turn on the POWER and open the CD cover.
2. As shown below, push S701 (CD DOOR) with a screwdriver or
other tool.
3. Press the CD button.
4. Check the objective lens to make sure that the laser diode is
emitting light. If not so, the auto power control circuit or
optical pickup would be damaged.
Verify that the objective lens moves vertically three times for
focus search.
Insert a precision
screw driver and push
SWITCH (S701)
1-4. FLEXIBLE CIRCUIT BOARD REPAIRING
• Keep the temperature of the soldering iron around 270 °C during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED
LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL
OR IN SUPPLEMENTS PUBLISHED BY SONY.
3
ZS-M30
1-7. CHECKS PRIOR TO PARTS REPLACEMENT AND ADJUSTMENTS (FOR MD SECTION)
Before performing repairs, perform the following checks to determine the faulty locations up to a certain extent.
Details of the procedures are described in “5 Electrical Adjustments”
Criteria for Determination
(Unsatisfactory if specified value is not satisfied)
Laser power check
Focus power check
C PLAY check
• 0.9 mW power
Specified value : 0.80 to 0.96 mW
• 7.0 mW power
Specified value : 6.8 to 7.2 mW
lop (at 7mW)
• Labeled on the optical pickup
Iop value ± 10%
• Error rate check
Specified value : For points a and b
C1 error : About 200
ADER : Below 2
Point C
C1 error :Below 50
AD error :Below 2
• Error rate check
Specified value:
a. When using test disc (MDW-74/AU-1)
C1 error : Below 80
ADER : Below 2
b. When using check disc (TDYS-1)
C1 error : Below 50
Self-recording/playback • CPLAY error rate check
check
Specified value:
C1 error : Below 80
ADER : Below 2
Measure if unsatisfactory:
• Clean the optical pick-up
• Adjust again
• Replace the optical pick-up
• Replace the optical pick-up
• Replace the optical pick-up
• Replace the optical pick-up
If always unsatisfactory:
• Replace the overwrite head
• Check for disconnection of the circuits around the
overwrite head
If occasionally unsatisfactory:
• Check if the overwrite head is distorted
• Check the mechanism around the sled
Note:
The criteria for determination above is intended merely to determine if satisfactory or not, and does not serve as the specified value for
adjustments.
When performing adjustments, use the specified values for adjustments.
4
SECTION 2
GENERAL
ZS-M30
This section is extracted from
instruction manual.
5
ZS-M30
6
ZS-M30
SECTION 3
DISASSEMBLY
r
The equipment can be removed using the following procedure.
Cabinet (rear)
BATT (B) board, BATT (A) board, power board
CD board
Main board,
LCD board
Set
Cabinet (front)
TOP board
Cabinet
(upper)
ASSY
MD block
ASSY
Tuner
board
SW (L) board,
jack board,
SW (R) board
MD board
REC board,
detect board
Over write head (HR901),
MD optical pick-up,
D SW board
Note : Follow the disassembly procedure in the numerical order given.
3-1. CABINET (REAR), CABINET (FRONT)
1Screws (+BVTP 3 X 14)
2Screws
(+BVTP 3 X 12) (silver)
4Main board
CN801
1Screws
(+BVTP 3 X 14)
3
Cabinet (rear)
2Screws
(+BVTP 3 X 12) (silver)
Cabinet (front)
3-2. BATT (B) BOARD, BATT (A) BOARD, POWER BOARD
5Screws (+BVTP 3 X 12) (silver)
Chissis, transformer
1Claw
3Claw
6Screws (+BVTP 3 X 10)
7
2
4
0CN902
9
Cabinet (rear)
BATT (A) board
BATT (B) board
Power board
8Screws (+BVTP 3 X 10)
7
ZS-M30
3-3. CABINET (UPPER) ASSY
1Screws (+BVTP 3 X 10)
Cabinet (upper) ASSY
2CN810
6Main board
(CN301)
7Main board
(CN302)
3Tuner board
(CN1)
8Main board
(CN303)
4CD board (CN703)
9
5Wire,parallel (22 core)
Main board (CN807)
0Wire,parallel (8 core)
SW (R) board (CN402)
Cabinet (front)
3-4. MAIN BOARD, LCD BOARD
Cabinet (upper) ASSY
1Wire,parallel (6 core)
Main board (CN803)
3Main board (CN805)
2Wire,parallel (19 core)
Main board (CN808)
7Screws (+BVTP 3 X 10)
0LCD board
Main board
6LCD board (CN404)
5
8
4Screws (+BVTP 3 X 10)
LCD1
9Remove solder (7 places)
4Screws (+BVTP 3 X 10)
8
ZS-M30
3-5. CD BOARD
Cabinet (upper) ASSY
2Wire,Parallel (16 core)
(CN701)
4
3Remove solder
(4 places)
CD board
1Screw (+P 2 X 6)
3-6. TOP BOARD
Cabinet (upper) ASSY
2
Top board
1Screws (+BVTP 2.6 X 10)
3-7. TUNER BOARD
2
Tuner board
1Screws (+BVTP 3 X 10)
Cabinet (front)
9
ZS-M30
3-8. MD BLOCK ASSY
3Screws (+BVTT 2.6 X 6)
Chassis (TU)
1Screws (+BVTP 3 X10)
4
1Screws (+BVTP3 X10)
2
MD block ASSY
(MT-ZSM30-168)
Cabinet (front)
3-9. SW (L) BOARD, JACK BOARD, SW (R) BOARD
1Screws (+BVTP 2.6 X 10)
Jack board
Retainer (A)
SW (L) board
3Screws (+BVTP 3 X 10)
Retainer (B)
2
5Screws (+BVTP 2.6 X 10)
4
6
SW (R) board
Cabinet (front)
10
ZS-M30
3-10. MD BOARD
1Screws (+BVTP 2.6 X 5)
Case (MD upper) shield
8Claw
2
4Screws, MD fitting
4Screws, MD fitting
0Op flexible board
MT-ZSM30-168
8Claw
qaWire,Parallel (7 core)
6Wire,parallel (9 core)
REC board (CN505)
qsCN601 (2pin)
9
8Claw
MD board
7Screws (+P 2.6 X 2.5)
3Wire,parallel (22 core)
Main board (CN807)
5
Case (MD lower) shield
3-11. REC BOARD, DETECT BOARD
Slider
8Remove solder 5
(2 places)
6Claws
DETECT board
2Claw
7
REC board
3
1Over write head flexible board
(CN504)
2Claws
4Move slider away from pin.
Chassis
11
ZS-M30
3-12. OVER WRITE HEAD (HR901), MD OPTICAL PICK-UP, D SW BOARD
1Screw (+P 1.7X2.5)
Over write head
(HR901)
4
Chassis
6D SW board
3
5Screws (1.4 X 2)
MD optical pick-up
(KMS-260B)
2Screws (+P 1.4 X 3.5)
12
ZS-M30
SECTION 4
TEST MODE
Refer to “5. ELECTRICAL ADJUSTMENT” for the test mode of CD section.
4-1. MD SECTION
1. PRECAUTIONS FOR USE OF TEST MODE
• As loading related operations will be performed regardless of the test mode operations being performed, be sure to check that the disc is
stopped before setting and removing it.
Even if the Z (MD EJECT) button is pressed while the disc is rotating during continuous playback, continuous recording, etc., the disc
will not stop rotating.
Therefore, it will be ejected while rotating.
Be sure to press the Z (MD EJECT) button after pressing the NO/CANCEL button and the rotation of disc is stopped.
1-1. Recording laser emission mode and operating buttons
• Continuous recording mode (CREC MODE)
• Laser power check mode (LDPWR CHECK)
• Laser power adjustment mode (LDPWR ADJUST)
• When pressing the YES/ENTER button.
4-2. SETTING THE TEST MODE
1. Set to standby state.
2. Press and hold the YES/ENTER button then press MD u t x t u t x
.
4-3. RELEASING THE TEST MODE
Remove the power cord to release the test mode.
4-4. BASIC OPERATIONS OF THE TEST MODE
All operations are performed with the following buttons: jogdial . , > , YES/ENTER and NO/CANSEL .
The functions of these buttons are as follows.
Function name
JOG ( > )
JOG ( . )
YES/ENTER
NO/CANCEL
Function
Proceeds the parameter/mode change.
Returns to the parameter/mode change.
Goes ahead. Determines the setting/selection.
Suspends.
13
ZS-M30
4-5. SELECTING THE TEST MODE
There are 9 types of test modes as shown below. The groups can be switched by turn the jog dial. After selecting the
group to be used, press the YES/ENTER button. After setting a certain group, turn the jog dial between these modes.
Display
TEMP ADJUST
LDPWR ADJUST
LDPWR CHECK
LOAD CHECK
S CURVE CHECK
EFBAL ADJUST
FBIAS ADJUST
FBIAS CHECK
CPLAY MODE
CREC MODE
DETRK CHECK
LOAD AGING
EEP MODE
Contents
Temperature compensation offset adjustment
Laser power adjustment
Laser power check
load check
S curve check
EF balance adjustment
Focus bias adjustment
Focus bias check
Continuous playback mode
Continuous recording mode
Detrack check
Load aging
Non-volatile memory control
• For details of each adjustment mode, refer to “5. Electrical Adjustments”.
• If a different mode has been selected by mistake, press the NO/CANCEL button to release that mode.
• EEP MODE is not used for servicing and therefore are not described in detail. If these modes are set accidentally, press the NO/CANCEL
button to release the mode immediately. Be especially careful this mode will overwrite the non-volatile memory and reset it, and as a
result, the unit will not operate normally.
•When selecting test mode, usually the message “TEMP ADJUST” appears. In two rare cases, however, another message may be shown.
1. After conclusion of automatic temperature compensation (starting from display “TEMP = 00”), the message “Disc Insert” appears.
2. The message “Disc Insert” is displayed right form the start.
In both cases press the YES/ENTER button while holding the EDIT button, thus displaying “TEMP ADJUST” and entering
normal test mode.
In order to cause “TEMP ADJUST” to be displayed whenever test mode is selected, execute the following steps.
1. Rotate the jog dial until “EEP MODE” is shown.
2. Press the YES/ENTER button to display “EEP READ”.
3. Press the YES/ENTER button to display “EEP XXXX”.
(The first two “X”-marks represent the address, the latter two the value).
4. Rotate the jog dial to set the address to 15.
5. Press the YES/ENTER button while holding the EDIT button.
6. Confirm that the display shows “EEP15XX >XX”.
7. Rotate the jog dial to set the value after the “>”-mark to FF.
8. Press the YES/ENTER button.
9. Confirm that the display shows “Complete”.
10.After that, confirm that the display turns to “EEP READ”.
11.Press the YES/ENTER button.
12.Confirm that the display shows “EEP15FF”.
13.Press the NO/CANCEL button.
14
ZS-M30
4-5-1. Operating the Continuous Playback Mode
1. Entering the continuous playback mode
1 Set the disc in the unit. (Whichever recordable discs or discs for playback only are available)
2 Potate the jog dial and display “CPLAY MODE”.
3 Press the YES/ENTER button to change the display to “CPLAY MID”.
AD = ”.
4 When access completes, the display changes to “C1 =
Note: The numbers “ ” displayed show you error rates and ADER.
2. Changing the parts to be played back
1 Press the YES/ENTER button during continuous playback to change the display as below.
CPLAY MID
CPLAY OUT
CPLAY IN
When pressed another time, the parts to be played back can be moved.
2 When access completes, the display changes to “C1 =
AD = ”.
Note: The numbers “ ” displayed show you error rates and ADER.
3. Ending the continuous playback mode
1 Press the NO/CANCEL button. The display will change to “CPLAY MODE”.
2 Press the Z (MD) button and take out the disc.
Note: The playback start addresses for IN, MID, and OUT are as follows.
IN : 40h cluster
MID : 300h cluster
OUT: 700h cluster
4-5-2. Operating the Continuous Recording Mode (Use only when performing self-recording/palyback check)
1. Entering the continuous recording mode
1 Set a recordable disc in the unit.
2 Rotate the jog dial and display “CRDE MODE”.
3 Press the YES/ENTER button to change the display to “CREC MID”.
4 When access completes, the display changes to “CREC (
)” and “REC ” lights up.
Note: The numbers “ ” displayed shows you the recording position addresses.
2. Changing the parts to be recorded
1 When the YES/ENTER button is pressed during continuous recording, the display changes as below.
CREC MID
CREC OUT
CREC IN
When pressed another time, the parts to be recorded can be changed. “REC ” goes off.
)” and “REC ” lights up.
2 When access completes, the display changes to “CREC (
Note: The numbers “ ” displayed shows you the recording position addresses.
3. Ending the continuous recording mode
1 Press the NO/CANCEL button. The display changes to “CREC MODE” and “REC ” goes off.
2 Press the Z (MD) button and take out the disc.
Note 1: The recording start addresses for IN, MID, and OUT are as follows.
IN : 40h cluster
MID : 300h cluster
OUT: 700h cluster
Note 2: The NO/CANCEL button can be used to stop recording anytime.
Note 3: Do not perform continuous recording for long periods of time above 5 minutes.
Note 4: During continuous recording, be careful not to apply vibration.
4-5-3. Non-storage memory mode (EEP mode)
This is the mode to read write the contents of the non-volatile storage memory.
This mode is not used for servicing.
If you accidentally enter this mode, exit immediately by pressing the NO/CANCEL button.
15
ZS-M30
4-6. FUNCTIONS OF OTHER BUTTONS
Function
Contents
Sets continuous playback when pressed in the STOP state. When pressed during continuous
playback, the tracking servo turns ON/OFF.
Stops continuous playback and continuous recording.
u (MD)
x
(MD)
M
The sled moves to the outer circumference only when this is pressed.
m
The sled moves to the inner circumference only when this is pressed.
Switches the displayed contents each time the button is pressed
Ejects the disc
DISPLAY
Z (MD)
When pressed during continuous playback, switches between recording start stop.
REC/REC MODE
4-7. TEST MODE DISPLAYS
Each time the DISPLAY button is pressed, the display changes in the following order.
1. Mode display
Displays “TEMP ADJUST”, “CPLAYMODE”, etc.
Mode display
2. Error rate display
Displays the error rate in the following way.
AD =
C1 =
C1 = Indicates the C1 error.
AD = Indicates ADER.
Error rate display
Address display
Auto gain display
(Not used in servicing)
3. Address display
The address is displayed as follows. (MO: recordable disc, CD: playback only disc)
Press the REPEAT buttons at the same time to switches between the groove display
and pit display.
h=
s=
(MO pit and CD)
h=
a=
(MO groove)
h = Indicates the header address.
s = Indicates the SUBQ address.
a = Indicates the ADIP address.
IVR display
(Not used in servicing)
Note: “–” is displayed when servo is not imposed.
4. Auto gain display (Not used in servicing)
The auto gain is displayed as follows.
AG F = T =
5. IVR display (Not used in servicing)
The IVR is displayed as follows.
[ ][
][ ]
4-8.MEANINGS OF OTHER DISPLAYS
Display
SHUF
PGM
REC
TOC EDIT
TRACK
TIMER
MONO
16
Contents
Contents When Lit
When Off
During continuous playback (CLV: ON) STOP (CLV: OFF)
Tracking servo ON
Tracking servo OFF
Recording mode OFF
Recording mode ON
ABCD adjustment completed
Pit
CLV-S
FCS/TRK/AUTO GAIN successful
Groove
CLV-A
FCS successful, TRK unsuccessful
ZS-M30
SECTION 5
ELECTRICAL ADJUSTMENTS
5-1.TUNER SECTION
LW FREQUENCY COVERAGE ADJUSTMENT
reading on digital
voltmeter
Adjustment value: 5.4 to 6.0V
0.4 to 1.1V
Adjust part Frequency display
AM Section
CT4
Confirmation
RADIO BAND button : MW or LW
Volume : MIN
AM RF signal
generator
Put the lead-wire
antenna close to
the supplisd MW/LW
loop antenna.
279kHz
153kHz
LW TRACKING ADJUSTMENT
Adjust for a maximum reading on level meter.
L4
162kHz
CT3
261kHz
FM IF ADJUSTMENT
Adjust for a maximum reading on level meter.
L6
10.7MHz
30% amplitude modulation by 400Hz
signal.
Output level : as low as possible
FM Section
FM FREQUENCY COVERAGE ADJUSTMENT
Adjust part Frequency display
RADIO BAND button : FM
Volume : MIN
Confirmation
Confirmation
reading on digital
voltmeter
1.4 to 2.4V
2.7 to 3.7V
87.5kHz
108kHz
FM RF signal
generator
FM TRACKING ADJUSTMENT
0.01 uF
Adjust for a maximum reading on level meter.
L1
87.5MHz
CT1
108MHz
telescopic
antenna
terminal
22.5kHz frequency deviation by
400Hz signal.
Output level : as low as possible
Frequency Coverage Adjustment
Connect Location :
Digital
voltmeter
level meter
47KΩ
+
—
+
–
C5
C6
JW10
8
R2
JW6
D6
CT4
JW7
C10
R6
JW5
JW4
C43
R32
C12
C47
Q4
L5
R13 C26 R14 C27
9
R3
CT3
R30
C11
C51
C44
R28
FL1
MW FREQUENCY COVERAGE ADJUSTMENT
CT2
R31
L2
C4
C45
Q3
D2
Q1
Q2
AM IF ADJUSTMENT
Adjust for a maximum reading on level meter.
T1
450kHz
R5
C46
JC3
C54
C8
D3
R4
L4
C7
L3
C9
JW3
JW2
D4
D5
L7
• Repeat the procedures in each adjustment several times, and the
frequency coverage and tracking adjustments should be finally
done by the trimmer capacitors.
D7
JW1
Adjustment Location : Tuner board (See page 18)
D8
TUNER BOARD (SIDE B)
D9
LINE OUT
JW4
(VT)
R7
set
100KΩ
reading on digital
Adjust part
Frequency display
voltmeter.
Adjustment value: 1.0V
L5
531kHz
Standaed value: 0.7 to 1.3V
Confirmation
1,611kHz
5.1 to 5.9V
MW TRACKING ADJUSTMENT
Adjust for a maximum reading on level meter.
L3
621kHz
CT2
1,404kHz
17
ZS-M30
Adjustment Location:
CT2 : MW Tracking Adjustment
CT3 : LW Tracking Adjustment
[TUNER BOARD]
(Component side)
CT4 : LW Frequency Coverage Adjustment
L3 : MW Tracking Adjustment
L4 : LW Tracking Adjustment
L5 : MW Frequency
Coverage Adjustment
L1 : FM Tracking Adjustment
CT1 : FM Tracking Adjustment
L6 : FM IF Adjustment
T1 : AM IF Adjustment
18
ZS-M30
5-2. MD SECTION
1. PARTS REPLACEMENT AND ADJUSTMENT
• Check and adjust the mechanism deck as follows.
The procedure changes according to the part replaced.
• Abbreviation
OP
: Optical pick-up
OWH : Overwrite head
• Laser power check
• Focus bias check
• C PLAY check
• Self-recording/playback check
OK
NG
Check the sled and spindle
mechanisms.
Other causes can be suspected.
Parts Replacement and Repair
Has the OWH been replaced?
YES
NO
Has OP, IC603, IC502, or
IC504 been replaced?
NO
YES
Initial setting of the adjustment value
Has OP or IC603 been replaced?
NO
YES
IOP information recording
(IOP value labeled on OP)
Has IC603 or D501
been replaced?
NO
YES
Temperature compensation offset adjustment
• Laser power adjustment
• EF balance adjustment
• Focus bias adjustment
• Error rate adjustment
• Focus bias check
• Auto gain adjustment
19
ZS-M30
2. PRECAUTIONS FOR CHECKING LASER DIODE
EMISSION
To check the emission of the laser diode during adjustments, never
view directly from the top as this may lose your eye-sight.
3. PRECAUTIONS FOR USE OF OPTICAL PICK-UP
(KMS-260B)
As the laser diode in the optical pick-up is easily damaged by static
electricity, solder the laser tap of the flexible board when using it.
Before disconnecting the connector, desolder first. Before connectingthe connector, be careful not to remove the solder. Also take
adequate measures to prevent damage by static electricity. Handle
the flexible board with care as it breaks easily.
pick- up
flexible board
4. Use the following tools and measuring device.
• Check Disc (MD) TDYS-1
(Part No. 4-963-646-01)
• Test Disc (MDW-74/AU-1) (Part No. 8-892-341-41)
• Laser power meter LPM-8001 (Part No. J-2501-046-A)
or MD Laser power meter 8010S (Part No. J-2501-145-A)
• Oscilloscope (Measure after performing CAL of prove)
• Digital voltmeter
• Thermometer
5. When observing several signals on the oscilloscope, etc., make
sure that VC and ground do not connect inside the oscilloscope.
(VC and ground will become short-circuited)
6. Using the above jig enables the waveform to be checked with-out
the need to solder.
(Refer to Service Note on page 3)
7. As the disc used will affect the adjustment results, make sure
that not dusts nor fingerprints are attached to it.
Laser Power Meter
When performing laser power checks and adjustment (electrical
adjustment), use of the new MD laser power meter 8010S (Part No.
J-2501-145-A) instead of the conventional laser power meter is convenient.
It sharply reduces the time and trouble to set the laser power meter
sensor onto the objective lens of optical pick-up.
laser tap
Optical pick-up flexible board
4. PRECAUTIONS FOR ADJUSTMENTS
1. When replacing the following parts, perform the adjustments
and checks with in the order shown in the following table.
Optical
Pick-up IC603
BD Board
D501
IC502, IC504 IC506
1. Recording of IOP
information
(Value written in
the pick-up)
2.Temperature
compensation
offset adjustment
3.Laser power
adjustment
4.EF balance
adjustment
5.Focus bias
adjustment
6.Error rate check
2. Set the test mode when performing adjustments.
After completing the adjustments, release the test mode.
Perform the adjustments and checks in “group S” of the test
mode.
3. Perform the adjustments to be needed in the order shown.
20
5. CREATING CONTINUOUSLY-RECORDED DISC
* This disc is used in focus bias adjustment and error rate check.
The following describes how to create a continuous recording
disc.
1. Insert a disc (blank disc) commercially available.
2. Turn the JOG dial to display “CREC MODE”.
3. Press the YES/ENTER button again to display “CREC MID”.
Display “CREC (0300)” and start to recording.
4. Complete recording within 5 minutes.
5. Press the NO/CANCEL button and stop recording.
6. Press the Z (MD) button and remove the disc.
The above has been how to create a continuous recorded data for
the focus bias adjustment/check and MO error rate check.
Note:
• Be careful not to apply vibration during continuous recording.
ZS-M30
6. CHECK PRIOR TO REPAIRS
These checks are performed before replacing parts according to
“approximate specifications” to determine the faulty locations. For
details, refer to “Checks Prior to Parts Replacement and Adjustments”(See page 4).
6-1. Laser Power Check
(Optical pick-up label)
KMS260B
27X40
B0825
lOP=82.5 mA in this case
lOP (mA) = Digital voltmeter reading (mV)/3.3 (Ω)
Connection:
laser
power meter
5. Press the NO/CANCEL button to display “LDPWR CHECK”
and stop the laser emission.
(The NO/CANCEL button is effective at all times to stop the
laser emission)
Note 1: After step 4, each time the YES/ENTER button is pressed,
the display will be switched “LD 0.7 mW $ ”,
“LD 6.2 mW $
”,
and “LD WP
$ ”. Nothing needs to be performed
here.(
= correction)
Optical pick-up
objective lens
digital voltmeter
TP502 (I+3V)
TP503 (IOP)
C520 C522
3635 30 25
37
IC502
C519 40
(TE)
1
5
C518
1012
R515
R516
R512
C512
R503
R504
Q503
R502
R510
C502
L501
R508
R514
R509
R505
Q505
L503
20
C505
Q501
Q504
C607
C521
15
13
Q507
C508
R633
R519
24
R513
Q502
C611
45
48
C517
R517
R518
R622
R52
MD BOARD (SIDE B)
Q506
C511
C506
TP502
R511
(I+3V)
TP503
(IOP)
L506
Checking Procedure:
1. Set the laser power meter on the objective lens of the optical
pick-up. (When it cannot be set properly, press the m but-ton
or M button to move the optical pick-up)
Connect the digital voltmeter to TPO 502 (I+3 V) and TP503 (IOP)
on the MD board.
2. Turm the JOG dial to display “LDPWR CHECK”.
3. Press the YES/ENTER button once to display “LD 0.9 mW $
”. Check that the reading of the laser power meter become
0.80 to 0.96 mW.
4. Press the YES/ENTER button once more to display “LD 7.0
mW $ ”. Check that the reading the laser power meter and
digital voltmeter satisfy the specified value.
Specified Value:
Laser power meter reading : 6.8 - 7.2 mW
Digital voltmeter reading : Value on the optical pick-up label
± 10 %
6-2. Focus Bias Check
Change the focus bias and check the focus tolerance amount.
Checking Procedure:
1. Load the test disc (MDW-74/AU-1).
2. Turn the JOG dial to display “CPLAY MODE”.
3. Press the YES/ENTER button twice to display “CPLAY MID”.
4. Press the NO/CANCEL button when “C1 =
AD = ”
is displayed.
5. Turn the JOG dial to display “FBIAS CHECK”.
6. Press the YES/ENTER button to display “
/
c = ”.
The first four digits indicate the C1 error rate, the two digits
after (( / )) indicate ADER, and the 2 digits after “c =” indicate
the focus bias value.
Check that the C1 error is below 50 and ADER is below 2.
7. Press the YES/ENTER button to display “
/
b = ”.
Check that the C1 error is about 200 and ADER is below 2.
8. Press the YES/ENTER button to display “
/
a = ”.
Check that the C1 error is about 200 and ADER is below 2.
9. Press the NO/CANCEL button, then press the Z (MD)
button and take out the test disc.
6-3. C PLAY Check
MO Error Rate Check
Checking Procedure:
1. Load the test disc (MDW-74/AU-1).
2. Turn the JOG dial to display “CPLAY MODE”.
3. Press the YES/ENTER button to display “CPLAY MID”.
4. The display changes to “C1 =
AD =
”.
5. If the C1 error rate is below 80, check that ADER is below 2.
6. Press the NO/CANCEL button to stop playback, then press
the Z (MD) button and take out the test disc.
CD Error Rate Check
Checking Procedure:
1. Load the check disc (MD) TDYS-1.
2. Turn the JOG dial to display “CPLAY MODE”.
3. Press the YES/ENTER button twice to display “CPLAY MID”.
AD =
”.
4. The display changes to “C1 =
5. Check that the C1 error rate is below 50.
6. Press the NO/CANCEL button to stop playback, then press
the Z (MD) button and take out the check disc.
21
ZS-M30
Connection:
laser
power meter
Optical pick-up
objective lens
digital voltmeter
TP502 (I+3V)
TP503 (IOP)
Adjusting Procedure:
1. Turn the JOG dial to display “TEMP ADJUST”.
2. Press the YES/ENTER button to select the “TEMP ADJUST”
mode.
3. “TEMP = ” and the current temperature data will be displayed.
4. To save the data, press the YES/ENTER button.
When not saving the data, press the NO/CANCEL button.
5. When the YES/ENTER button is pressed, “TEMP = SAVE”
will be displayed and turned back to “TEMP ADJUST” display
then. When the NO/CANCEL button is pressed, “TEMP
ADJUST” will be displayed immediately.
Specified Value:
The “TEMP =
” should be within “E0 - EF”, “F0 - FF”, “00 0F”,“10 - 1F” and “20 - 2F”.
20
5
C518
1012
R508
R512
C512
R503
R504
Q503
R516
R514
R515
C505
1
R502
R510
R505
Q505
L503
C521
15
13
Q507
C508
R633
R519
24
R513
Q502
C611
(TE)
45
48
R509
C607
7. TEMPERATURE COMPENSATION OFFSET
ADJUSTMENT
Save the temperature data at that time in the non-volatile memory
as 25 °C reference data.
Note:
1. Usually, do not perform this adjustment.
2. Perform this adjustment in an ambient temperature of 22 °C to
28 °C.
Perform it immediately after the power is turned on when the
internal temperature of the unit is the same as the ambient tem
perature of 22 °C to 28 °C.
3. When D501 has been replaced, perform this adjustment after
the tem-perature of this part has become the ambient tempera
ture.
Q504
Q501
R622
C517
R517
Note: After the TEST MODE is entered, insert the disc.
C520 C522
3635 30 25
R518
37
IC502
C519 40
R52
MD BOARD (SIDE B)
C502
Checking Procedure:
1. Load a recordable disc (blank disc).
2. Turn the JOG dial to display “CREC MODE”.
3. Press the YES/ENTER button to display “CREC MID”.
4. When recording starts, lights up “ REC ” and display “CREC
(@@@@)” (@@@@ is the address).
5. About 1 minute later, press the NO/CANCEL button to
stop continuous recording.
6. Turn the JOG dial to display “CPLAY MODE”.
7. Press the YES/ENTER button to display “CPLAY MID”.
8. “C1 =
AD = ” will be displayed.
9. Check that the C1 error becomes below 80 and the ADER below 2.
10.Press the NO/CANCEL button to stop play back, then press
the Z (MD) button and take out the disc.
8. LASER POWER ADJUSTMENT
L501
6-4. Self-Recording/playback Check
Prepare a continuous recording disc using the unit to be repaired
and check the error rate.
Q506
C511
C506
TP502
R511
(I+3V)
TP503
(IOP)
L506
Adjusting Procedure:
1. Set the laser power meter on the objective lens of the optical
pick-up. (When it cannot be set properly, press the m but-ton
or M button to move the optical pick-up)
Connect the digital voltmeter to TP502 (I+3 V) and TP503
(IOP) on the MD board.
2. Turn the JOG dial to display “LDPWR ADJUST”.
(Laser power: For adjustment)
3. Press the YES/ENTER button once to display “LD 0.9 mW
”.
$
4. Turn the JOG dial so that the reading of the laser power meter
becomes 0.85 to 0.91 mW. Press the YES/ENTER button after
setting the range knob of the laser power meter, and save the
adjustment results. (“LD SAVE $ ” will be displayed for a
moment)
5. Then “LD 7.0 mW $
” will be displayed.
6. Turn the JOG dial and adjust so that the reading on the laser
power meter is 6.9 to 7.1 mW. Press the YES/ENTER button to
save the setting.
Note: Do not perform the emission with 7.0 mW more than 15 sec
onds continuously.
7. Turn the JOG dial to display “LDPWR CHECK”.
8. Press the YES/ENTER button once to display “LD 0.9mW
$ ”. Check that the reading of the laser power meter become
0.85 to 0.91 mW.
9. Press the YES/ENTER button once more to display “LD 7.0
mW $
”. Check that the reading the laser power meter and
digital voltmeter satisfy the specified value.
Note down the digital voltmeter reading value.
22
ZS-M30
Specified Value:
Laser power meter reading : 7.0 ± 0.2 mW
Digital voltmeter reading : Value on the optical pick-up label
± 10%
Connection:
oscilloscope
(DC range)
(Optical pick-up label)
9. EF BALANCE ADJUSTMENT
Note 1: Data will be erased during MO reading if a recorded
disc is used in this adjustment.
Note 2: If the traverse waveform is not clear, connect the
oscilloscope as shown in the following figure so that
it can be seen more clearly.
oscilloscope
(DC range)
517
C520 C522
3635 30 25
R518
37
IC502
C519 40
C526
R519
24
C521
20
Adjusting Procedure:
1. Connect an oscilloscope to TP504 (TE) and TP506 (VC) on
the MD board.
2. Load a disc (any available on the market). (Refer to Note 1)
3. Press the M button to move the optical pick-up outside the
pit.
4. Turn the JOG dial to display “EFBAL ADJUST”.
5. Press the YES/ENTER button to display “EFB = MO-R”.
(Laser power READ power/Focus servo ON/tracking servo OFF/
spindle (S) servo ON)
6. Turn the JOG dial so that the waveform of the oscilloscope be
comes the specified value.
of “EFB = ” changes
(When the JOG dial is turned, the
and the waveform changes ) In this adjust-ment, wave form var
ies at intervals of approx. 2 %. Adjust the waveform so that the
specified value is satisfied as much as possible.
(Read power traverse adjustment)
Traverse Waveform
A
R540
C546
VC
B
R532
R54
MD BOARD
(SIDE B)
Specification : A = B
TP505
(RF)
R531
TP504
(TE)
C520 C522
3635 30 25
R518
37
IC502
C519 40
C526
R524
R535
TP506
(VC)
R525 R533
R538
C550
R542
L509
R531
R524
TP505
(RF)
Ω
517
R532
R54
TP506
(VC)
TP504
(TE)
10. Press the NO/CANCEL button to display “LDPWR
CHECK” and stop the laser emission.
(The NO/CANCEL button is effective at all times to stop
the laser emission)
Note 1: After step 9, each time the YES/ENTER button is pressed, the
”, “LD 6.2 mW $
”,
display will be switched “LD 0.7 mW $
and “LD WP
$
”. Nothing needs to be performed here.
= correction)
(
C546
R535
L509
lOP=82.5 mA in this case
lOP (mA) = Digital voltmeter reading (mV)/3.3 (Ω)
[MD BOARD]
(SIDE B)
R525 R533
R538
C550
R542
R540
KMS260B
27X40
B0825
R519
24
20
C521
7. Press the YES/ENTER button and save the result of adjustment to the non-volatile memory. (“EFB = SAVE” will be
displayed for a moment. Then “EFB = MO-W” will be displayed)
8. Turn the JOG dial so that the waveform of the oscilloscope be
comes the specified value.
(When the JOG dial is turned, the of “EFB- ” changes and
the waveform changes) In this adjustment, waveform varies at
intervals of approx. 2%. Adjust the waveform so that the specified value is satisfied as much as possible.
(Write power traverse adjustment)
Traverse Waveform
A
VC
B
Specification : A = B
23
ZS-M30
9. Press the YES/ENTER button, and save the adjustment results in the non-volatile memory. (“EFB = SAVE” will be
displayed for a moment)
10. “EFB = MO-P” will be displayed.
The optical pick-up moves to the pit area automatically and
servo is imposed.
11. Turn the JOG dial until the waveform of the oscilloscope moves
closer to the specified value.
In this adjustment, waveform varies at intervals of approx. 2%.
Adjust the waveform so that the specified value is satisfied as
much as possible.
Traverse Waveform
A
VC
B
Specification : A = B
12. Press the YES/ENTER button, and save the adjustment results in the non-volatile memory. (“EFB = SAVE” will be
displayed for a moment)
Next “EFBAL ADJUST” is displayed. The disc stops rotating
automatically.
13. Press the Z (MD) button and take out the disc.
14. Load the check disc (MD) TDYS-1.
15. Press the YES/ENTER button to display “EFB =
CD”.
Servo is imposed automatically.
16. Turn the JOG dial so that the waveform of the oscilloscope
moves closer to the specified value.
In this adjustment, waveform varies at intervals of approx.
2%.
Adjust the waveform so that the specified value is satisfied as
much as possible.
10. FOCUS BIAS ADJUSTMENT
Adjusting Procedure:
1. Load the continuously-recorded disc.
(Refer to “5. CREATING CONTINUOUSLY-RECORDED
DISC”)
2. Turn the JOG dial to display “CPLAY MODE”.
3. Press the YES/ENTER button to display “CPLAY MID”.
AD = ”
4. Press the NO/CANCEL button when “C1 =
is displayed.
5. Turn the JOG dial to display “FBIAS ADJUST”.
6. Press the YES/ENTER button to display “
/ a = ”.
The first four digits indicate the C1 error rate, the two digits
after “ / ” indicate ADER, and the 2 digits after “a =” indicate
the focus bias value.
7. Turn the JOG dial clockwise and find the focus bias value at
which the C1 error rate becomes about 200 (Refer to Note 2).
8. Press the YES/ENTER button to display “
/b=
”.
9. Turn the JOG dial counterclockwise and find the focus bias
value at which the C1 error rate becomes about 200.
10. Press the YES/ENTER button to display “
/ c = ”.
11. Check that the C1 error rate is below 50 and ADER is 00.
Then press the YES/ENTER button.
12. If the “(
)” in “ - (
)” is above 20, press the
YES/ENTER button.
If below 20, press the NO/CANCEL button and repeat the
adjustment from step 2.
13. Press the Z (MD) button and take out the disc.
Note 1: The relation between the C1 error and focus bias is as shown in
the following figure. Find points A and B in the following figure
using the above adjustment. The focal point position C is automatically calculated form points A and B.
Note 2: As the C1 error rate changes, perform the adjustment using the
average value.
C1 error
about
Traverse Waveform
Focus bias value
(F.BIAS)
A
B
C
A
VC
B
Specification : A = B
17. Press the YES/ENTER button, display “EFB = SAVE” for
a moment and save the adjustment results in the non-volatile
memory.
Next “EFBAL ADJUST” will be displayed.
18. Press the Z (MD) button and take out the disc.
11. ERROR RATE CHECK
11-1. CD Error Rate Check
Checking Procedure:
1. Load the check disc (MD) TDYS-1.
2. Turn the JOG dial and display “CPLAY MODE”.
3. Press the YES/ENTER button twice and display “CPLAY
MID”.
4. The display changes to “C1 =
AD =
”.
5. Check that the C1 error rate is below 20.
6. Press the NO/CANCEL button to stop playback, then press
the Z (MD) button and take out the check disc.
11-2. MO Error Rate Check
Checking Procedure:
1. Load the continuously-recorded disc. (Refer to “5. CREATING
CONTINUOUSLY-RECORDED DISC”)
2. Turn the JOG dial to display “CPLAY MODE”.
3. Press the YES/ENTER button to display “CPLAY MID”.
4. The display changes to “C1 =
AD = ”.
5. If the C1 error rate is below 50, check that ADER is 00.
6. Press the NO/CANCEL button to stop playback, then
press the Z (MD) button and take out the test disc.
24
ZS-M30
12. FOCUS BIAS CHECK
Change the focus bias and check the focus tolerance amount.
Checking Procedure:
1. Load the continuously-recorded disc. (Refer to “5. CREATING
CONTINUOUSLY-RECORDED DISC”)
2. Turn the JOG dial to display “CPLAY MODE”.
3. Press the YES/ENTER button twice to display “CPLAY
MID”.
4. Press the NO/CANCEL button when “C1 =
AD = ”
is displayed.
5. Turn the JOG dial to display “FBIAS CHECK”.
6. Press the YES/ENTER button to display “
/
c = ”.
The first four digits indicate the C1 error rate, the two digits
after “ / ” indicate ADER, and the 2 digits after “c =” indicate
the focus bias value.
Check that the C1 error is below 50 and ADER is below 2.
7. Press the YES/ENTER button and display “
/ b = ”.
Check that the C1 error is about 200 and ADER is below 2.
8. Press the YES/ENTER button and display “
/ a = ”.
Check that the C1 error is about 200 and ADER is below 2.
9. Press the NO/CANCEL button, then press the Z (MD)
button and take out the disc.
5-3. CD SECTION
Set the CD test mode when performing confirmations.
After completing the confirmation, release the CD test mode.
In the CD test mode, the set works as following sequence.
CD test mode sequence:
CD test mode
Enter the
CD test mode
1. CD
test mode 1
Press the
x (CD) button
2.
CD
test mode 2
Press the
u (CD) button
Press the
x (CD) button
Note 1: If the C1 error and ADER are above other than the speci-
fied value at points A (step 8. in the above) or B (step 7. in
the above), the focus bias adjustment may not have been
carried out properly. Adjust perform the beginning again.
Press the
u (CD) button
3. STOP mode 2
Press the u ,(CD)
button.
Press the x (CD)
button.
4. FOCUS mode
Press the u ,(CD)
button.
5. ALL SERVO
ON mode
Press the x (CD)
button.
Press the u ,(CD)
button.
6. LPC OFF
mode
Press the x (CD)
button.
Press the u ,(CD)
button.
7. TRACKING
GAIN UP mode
Press the x (CD)
button.
Press the u ,(CD)
button.
8. High speed
mode
Press the x (CD)
button.
Press the u ,(CD)
button.
25
ZS-M30
2. Connect an oscilloscope to TP (TE) and TP (VC) on the CD
board.
Connection:
oscilloscope
(DC range)
TP (VC)
TP (TE)
Display
R721
C
R7
JW724
10
Display
C720
41
Q702
PGM
JW720
R783
R717
C726
C723
R786
R708
TP
(RF)
C716 TP(TE)
C715
R716
C714
C722
R715
Q701
6. Press x (CD)button to enter CD test mode (STOP MODE 1)
and to show the following display.
C731
R722
JW701
88
JW719
JW715
21
J
[CD BOARD] (SIDE B)
IC702
C730
Entering the CD test Mode
Press POWER button to turn on the power.
Place CD into tray (TOC data of the CD will be read).
Press and hold EDIT button, then press CD buttons in the
following order:
u (CD)t x (CD)t u (CD)t x (CD)
4. All LED and LCD segments start flashing.
5. Press any button to stop flashing of LED and LCD segments and
to shoe the following display.
JW70
1.
1.
2.
3.
TP
(VC)
R713
C721
R718
R719
C712
3. Confirm that the traverse level of waveform satisfy specified
value as follows.
Traverse Waveform
81
PGM
2. STOP Mode 2
1. Press the x (CD) button to enter the STOP mode 2, and display as below.
Display
82
PGM
A
VC
B
A=B
Specified Value:
traverse level: 0.65 to 1.20 Vp-p
4. ALL SERVO ON Mode 1
(RF Level and Jitter Confirmation 1)
1. Press the u (CD) button four times to enter the ALL SERVO
ON
mode 1 (start playback the disc) and display as below.
(All servo ON. LPC ON)
Display
2. Press the M and m button to move the optical pick-up to
position of the track where signal is recorded.
3. FOCUS Mode (Traverse Confirmation)
1. Press the u (CD ) button to enter the FOCUS mode and dis
play as below. (Focus servo ON. CLV-S, tacking and sled servo
OFF)
Display
FPGM
26
traverse level:
0.65 to 1.20 Vp-
P-
PGM
ZS-M30
2. Connect an osilloscope to TP (RF) and TP (VC) on the CD board.
Connection:
6. Releasing the CD Test Mode
1. Press the x (CD) button to stop rotate the disc.
2. Press the POWER button, then remove the power cord to
release the test mode.
oscilloscope
(DC range)
TP (RF)
TP (VC)
J
C731
JW719
JW715
21
C730
JW70
[CD BOARD] (SIDE B)
IC702
C720
Q702
41
JW701
R722
R721
C
R7
JW724
10
JW720
R717
C726
C723
R786
R708
TP
(RF)
C716 TP(TE)
C715
R716
C714
C722
R715
Q701
R783
TP
(VC)
R713
C721
R718
R719
C712
3. Confirm that the RF level and jitter of waveform satisfy specifiedvalues as follows.
RF signal Waveform
VOLT/DIV: 200 mV
TIME/DIV: 500 ns
RF level:
1.1 to1.3 Vp-p
Specified Values:
RF level : 1.1 to 1.3 Vp-p
jitteriless than 9nsec
5. LPC Mode
(RF Level and Jitter Confirmation 2)
1. Press the u button to enter the LPC OFF mode and display
as below. (All servo ON. LPC OFF)
Display
P-
OF
PGM
2. Confirm that the RF level and jitter of waveform satisfy specifiedvalues as follows.
Specified Values:
RF level : 0.9 to 1.4 Vp-p
jitteriless than 9nsec
If the RF level and jitter are out of specified values, measure again
after clean the object lens by an applicator with lens cleaning liquid.
27
ZS-M30
SECTION 6
DIAGRAMS
6-1. IC PIN FUNCTION DESCRIPTIONS
• MAIN BOARD IC801 System control (CXP740096-059Q)
Pin No.
Pin name
I/O
1
MD–PDOWN
O
Power down signal output to the MD mechanism coutroller(IC601)
2
MD–SRTS
I
System controller busy status monitor input from the MD mechanism controller
3
MD–PACK IN
I
MO disc detection signal input
4
MD–SCTS
I
MD mechanism controller busy status monitor input from the MD mechanism controller
5
MD–RST
O
Power supply on /off control signal output for the MD mechanism controller
6
MD–H
O
MD play control signal output to the A/D, D/A converter(IC604)
7
REC–H
8–10
11
B/L7V–SHORT
12
O
MD record signal output to the A/D, D/A converter (IC604)
—
Not used (OPEN)
I
Backlight voltage detection input
—
Not used (OPEN)
13
CD–MUTE
—
Not used (OPEN)
14
AU–MUTE
O
Audio mute drive signal output
—
Not used (OPEN)
—
Not used (OPEN)
15–17
18
SUR–CTR
19, 20
—
Not used (OPEN)
21
MEGA BASS
O
MEGA–BASS ON/OFF signal output
22
HP–SW
O
Headphones ON/OFF signal output
23
AU–CS
O
Audio chip select signal output
24
AU–DATA
O
Serial data output to the electrical volume (IC302)
25
AU–CLK
O
Serial data transfer clock signal output
—
Not used (OPEN)
30
LEO–OPERATION2
—
Not used (OPEN)
31
PA–STANDBY
O
Power amplifier ON/OFF signal output “ L ” : standby “ H ” power ON
32
P–CON2
—
Not used (OPEN)
33
LINE–MUTE
O
Line mute drive signal output
34
TU–MUTE
—
Not used (OPEN)
26–29
35
SUR
O
Panorama sound select signal output
36
LED–HIGHSPEED2
O
HIGHSPEED LED ON/OFF control signal output
37
LED–SURROUND2
O
Panorama sound LED ON/OFF control signal output
38
VDD–CONT
O
VDD 3.3V ON/OFF control signal output
39
TU–SFT
O
Level shift control signal output
40
RST
I
System reset signal input
41
VSS
—
42
XTAL
I
43
EXTAL
44
28
Description
Ground terminal
Main system clock input terminal (8MHz)
O
Main system clock output terminal (8MHz)
—
Not used (OPEN)
45
LCD–STB
O
LCD standby signal output
46
LCD–DATA
O
LCD serial data output
47
LCD–CLK
O
LCD clock signal output
48
SELECT–GND
—
Not used (OPEN)
49
SELECT
—
Not used (fixed “ H ” )
50
LED–OPERATION
—
Not used (OPEN)
51
LEO–HISPEED
—
Not used (OPEN)
52
AVSS
—
Ground terminal
53
AVREF
—
Reference voltage (3.3V) input for A/D converter
54
AVDD
—
Power supply terminal(3.3V)
55
KEY–AD1
I
Key input terminal
56
KEY–AD0
I
Key input terminal
57
JOG–B
I
Jog controller (B) input
ZS-M30
Pin No.
Pin name
I/O
Description
58
JOG–A
I
Jog controller (A) input
59
KEY–AD4
I
Key input terminal
60
KEY–AD3
I
Key input terminal
61
KEY–AD2
I
Key input terminal
62
COM3.3V–SHORT
I
COM3.3V voltage detection terminal
63
LED–SURROUND
—
Not used (OPEN)
64
CD–POWER
O
Power supply ON/OFF signal output for CD servo system
65
CD–C2P0
—
Not used (OPEN)
66
CD–SPH
O
CD High speed recording control signal output
67
CD–AGC CONT
O
CD AGC signal output
68
CD–SCLK
O
Subcode Q data transfer clock signal output for CD DSP IC (IC702)
69
MD–SRXD
I
UART communication data input from the MD mechanism controller (IC601)
70
MD–STXD
O
UART communication data output to the MD mechanism controller (IC601)
71
—
Not used (OPEN)
72
—
Not used (OPEN)
73
CD–CLK
O
Serial data transfer clock signal output to the CD DSP IC (IC702)
74
CD–XLAT
O
Serial data latch pulse signal output to the CD DSP IC (IC702)
75
CD–DATA
O
Serial data output to the CD DSP IC (IC702)
76
CD–XRST
O
CD reset signal output to the CD RF AMP (IC701),CD DSP IC (IC702)
77
CD SENSE
I
Internal status (SENSE) input from the CD DSP IC (IC702)
78
CD–SCOR
I
Subcode sync (SO +S1) detection signal input from the CD DSP IC (IC702)
79
CD–SQSO
I
Subcode Q data input from the CD DSP IC (IC702)
80
CD–RFH
O
CD RF level select output
81
CD–SQCK
82,83
O
Subcode Q data reading clock signal output to the CD DSP IC (IC702)
—
Not used (OPEN)
84
CD–DOOR
I
CD door open/close signal input
85
RMC
I
Remote control signal input
86
TEX
I
Sub system clock input terminal (32.768KHz)
87
TX
O
Sub system clock output terminal (32.768KHz)
88
VSS
—
Ground terminal
89
VDD
—
Power supply terminal (3.3V)
—
Not used (OPEN)
O
LCD backlight control signal output
90-92
93
B/L–CONT
94
ACCHK
I
AC power supply voltage detection terminal
95
P–COM
O
Power ON/OFF control signal output
96
—
Not used (OPEN)
O
PLL serial chip enable signal output to the tuner IC (IC1)
97
TU–CE
98
TU–DATA
O
PLL serial data output to the tuner IC (IC1)
99
TU–CLK
O
PLL serial data transfer clock signal output to the tuner IC (IC1)
100
TU–COUNT
I
PLL serial data input from the tuner IC (IC1)
29
ZS-M30
• MD BOARD IC502 CXA2523AR (RF AMP, FOCUS/TRACKING ERROR AMP)
Pin No.
Pin Name
I/O
1
I
I
I-V converted RF signal I input from the optical pick-up block detector
2
J
I
I-V converted RF signal J input from the optical pick-up block detector
3
VC
O
Middle point voltage (+ 1.65 V) generation output terminal
4–9
A–F
I
Signal input from the optical pick-up detector
30
Pin Description
10
PD
I
Light amount monitor input from the optical pick-up block laser diode
11
APC
O
Laser amplifier output terminal to the automatic power control circuit
12
APCREF
I
13
GND
—
Reference voltage input terminal for setting laser power
Ground terminal
14
TEMPI
I
Connected to the temperature sensor
15
TEMPR
O
Output terminal for a temperature sensor reference voltage
16
SWDT
I
Writing serial data input from the CXD2654R (IC504)
17
SCLK
I
Serial data transfer clock signal input from the CXD2654R (IC504)
18
XLAT
I
Serial data latch pulse signal input from the CXD2654R (IC504)
19
XSTBY
I
Standby signal input terminal “L”: standby (fixed at “H” in this set)
20
F0CNT
I
Center frequency control voltage input terminal of internal circuit (BPF22, BPF3T, EQ)
inputfrom the CXD2654R (IC504)
21
VREF
O
22
EQADJ
I/O
Reference voltage output terminal Not used (open)
23
3TADJ
I/O
Center frequency setting terminal for the internal circuit (BPF3T)
24
VCC
—
Power supply terminal (+3.3V)
25
WBLADJ
I/O
Center frequency setting terminal for the internal circuit (BPF22)
26
TE
O
Tracking error signal output to the CXD2654R (IC504)
27
CSLED
I
Connected to the external capacitor for low-pass filter of the sled error signal
28
SE
O
Sled error signal output to the CXD2654R (IC504)
29
ADFM
O
FM signal output of the ADIP
30
ADIN
I
Receives a ADIP FM signal in AC coupling
31
ADAGC
I
Connected to the external capacitor for ADIP AGC
32
ADFG
O
ADIP duplex signal (22.05 kHz ± 1 kHz) output to the CXD2654R (IC504)
33
AUX
O
Auxiliary signal (I3 signal/temperature signal) output to the CXD2654R (IC504)
34
FE
O
Focus error signal output to the CXD2654R (IC504)
Center frequency setting terminal for the internal circuit (EQ)
35
ABCD
O
Light amount signal (ABCD) output to the CXD2654R (IC504)
36
BOTM
O
Light amount signal (RF/ABCD) bottom hold output to the CXD264R (IC504)
37
PEAK
O
Light amount signal (RF/ABCD) peak hold output to the CXD2654R (IC504)
38
RF
O
Playback EFM RF signal output to the CXD2654R (IC504)
39
RFAGC
I
Connected to the external capacitor for RF auto gain control circuit
40
AGCI
I
Receives a RF signal in AC coupling
41
COMPO
O
User comparator output terminal Not used (open)
42
COMPP
I
User comparator input terminal Not used (fixed at “L”)
43
ADDC
I/O
44
OPO
O
User operational amplifier output terminal Not used (open)
45
OPN
I
User operational amplifier inversion input terminal Not used (fixed at “L”)
46
RFO
O
RF signal output terminal
Connected to the external capacitor for cutting the low band of the ADIP amplifier
47
MORFI
I
Receives a MO RF signal in AC coupling
48
MORFO
O
MO RF signal output terminal
ZS-M30
• MD BOARD IC 504 CXD2654R
(DIGITAL SIGNAL PROCESSOR, DIGITAL SERVO SIGNAL PROCESSOR, EFM/ACIRC ENCODER/DECODER,
SHOCK PROOF MEMORY CONTROLLER, ATRAC ENCODER/DECODER)
Pin No.
Pin Name
I/O
Pin Description
Focus OK signal output to the MD mechanism controller (IC601)
1
MNT0 (FOK)
O
2
MNT1 (SHOCK)
O
3
MNT2 (XBUSY)
O
Busy monitor signal output to the MD mechanism controller (IC601)
4
MNT3 (SLOCK)
O
Spindle servo lock status monitor signal output to the MD mechanism controller (IC601)
5
SWDT
I
Writing serial data signal input from the MD mechanism controller (IC601)
6
SCLK
7
XLAT
I (S) Serial data latch pulse signal input from the MD mechanism controller (IC601)
8
SRDT
O (3) Reading serial data signal output to the MD mechanism controller (IC601)
“H” is output when focus is on (“L”: NG)
Track jump detection signal output to the MD mechanism controller (IC601)
I (S) Serial data transfer clock signal input from the MD mechanism controller (IC601)
9
SENS
O (3) Internal status (SENSE) output to the MD mechanism controller (IC601)
10
XRST
I (S) Reset signal input from the MD mechanism controller (IC601) “L”: reset
11
SQSY
O
12
DQSY
O
13
RECP
I
14
XINT
O
15
TX
I
16
OSCI
I
17
OSCO
O
Subcode Q sync (SCOR) output to the MD mechanism controller (IC601)
“L” is output every 13.3 msec Almost all, “H” is output
Digital In U-bit CD format subcode Q sync (SCOR) output to the MD mechanism
controller(IC601) “L” is output every 13.3 msec Almost all, “H” is output
Laser power selection signal input from the MD mechanism controller (IC601)“L”:
playback mode, “H”: recording mode
Interrupt status output to the MD mechanism controller (IC601)
Recording data output enable signal input from the MD mechanism controller(IC601)
Writing data transmission timing input (Also serves as the magnetic head on/off output)
System clock signal (512 Fs = 45.1584 MHz) input terminal
System clock signal (512 Fs = 45.1584 MHz) output terminal
Input terminal for the system clock frequency setting
18
XTSL
I
19
DIN0
I
20
DIN1
I
21
DOUT
O
22
DATAI
I
Serial data input terminal Not used (fixed at “L”)
23
LRCKI
I
L/R sampling clock signal (44.1 kHz) input terminal Not used (fixed at “L”)
24
XBCKI
I
Bit clock signal (2.8224 MHz) input terminal Not used (fixed at “L”)
25
ADDT
I
Recording data input from the A/D, D/A converter (IC604)
“L”: 45.1584 MHz, “H”: 22.5792 MHz (fixed at “H” in this set)
Digital audio signal input terminal when recording mode (for digital optical input) Not
used
Digital audio signal input terminal when recording mode (for digital optical input)
Digital audio signal output terminal when playback mode (for digital optical output)
Not used
26
DADI
I
Playback data input from the A/D, D/A converter (IC604)
27
LRCK
O
L/R sampling clock signal (44.1 kHz) output to the A/D, D/A converter (IC604)
28
XBCK
O
Bit clock signal (2.8224 MHz) output to the A/D, D/A converter (IC604)
29
FS256
O
Clock signal (11.2896 MHz) output terminal
30
DVDD
—
Power supply terminal (+3.3 V) (digital system)
31 – 34
A03
O
A00 O Address signal output to the D-RAM (IC505)
35
A10
O
Address signal output to the external D-RAM Not used (open)
36 – 40
A04 – A08
O
Address signal output to the D-RAM (IC505)
41
A11
O
Address signal output to the external D-RAM Not used (open)
42
DVSS
—
Ground terminal (digital system)
43
XOE
O
Output enable signal output to the D-RAM (IC505) “L” active
44
XCAS
O
Column address strobe signal output to the D-RAM (IC505) “L” active
45
A09
O
Address signal output to the D-RAM (IC505)
31
ZS-M30
Pin No.
Pin Name
I/O
46
XRAS
O
Row address strobe signal output to the D-RAM (IC505) “L” active
47
XWE
O
Write enable signal output to the D-RAM (IC505) “L” active
48
D1
I/O
49
D0
I/O
50
D2
I/O
32
51
D3
52
MVCI
53
ASYO
54
ASYI
55
AVDD
56
BIAS
Pin Description
Two-way data bus with the D-RAM (IC505)
I/O
I (S) Digital in PLL oscillation input from the external VCO Not used (fixed at “L”)
O
Playback EFM full-swing output terminal
I (A) Playback EFM asymmetry comparator voltage input terminal
—
Power supply terminal (+3.3 V) (analog system)
I (A) Playback EFM asymmetry circuit constant current input terminal
57
RFI
58
AVSS
I (A) Playback EFM RF signal input from the CXA2523AR (IC502)
59
PCO
O (3) Phase comparison output for master clock of the recording/playback EFM master PLL
60
FILI
I (A) Filter input for master clock of the recording/playback master PLL
61
FILO
O (A) Filter output for master clock of the recording/playback master PLL
62
CLTV
I (A) Internal VCO control voltage input of the recording/playback master PLL
—
Ground terminal (analog system)
63
PEAK
I (A) Light amount signal (RF/ABCD) peak hold input from the CXA2523AR (IC502)
64
BOTM
I (A) Light amount signal (RF/ABCD) bottom hold input from the CXA2523AR (IC502)
65
ABCD
66
FE
67
AUX1
68
VC
69
ADIO
70
AVDD
I (A) Light amount signal (ABCD) input form the CXA2523AR (IC502)
I (A) Focus error signal input from the CXA2523AR (IC502)
I (A) Auxiliary signal (I3 signal/temperature signal) input from the CXA2523AR (IC502)
I (A) Middle point voltage (+1.65 V) input from the CXA2523AR (IC502)
O (A) Monitor output of the A/D converter input signal Not used (open)
—
Power supply terminal (+3.3 V) (analog system)
71
ADRT
I (A) A/D converter operational range upper limit voltage input terminal (fixed at “H” in this set)
72
ADRB
I (A) A/D converter operational range lower limit voltage input terminal (fixed at “L” in this set)
73
AVSS
74
SE
75
TE
76
DCHG
—
Ground terminal (analog system)
I (A) Sled error signal input from the CXA2523AR (IC502)
I (A) Tracking error signal input from the CXA2523AR (IC502)
I (A) Connected to the +3.3 V power supply
77
APC
78
ADFG
I (A) Error signal input for the laser automatic power control Not used (fixed at “H”)
79
F0CNT
O
Filter f0 control signal output to the CXA2523AR (IC502)
80
XLRF
O
Serial data latch pulse signal output to the CXA2523AR (IC502)
81
CKRF
O
Serial data transfer clock signal output to the CXA2523AR (IC502)
82
DTRF
O
Writing serial data output to the CXA2523AR (IC502)
83
APCREF
O
84
TESTO
—
Not used (OPEN)
85
TRDR
O
Tracking servo drive PWM signal (–) output to the BH6511FS (IC501)
I (S) ADIP duplex FM signal (22.05 kHz ± 1 kHz) input from the CXA2523AR (IC502)
Control signal output to the reference voltage generator circuit for the laser automatic
powercontrol
86
TFDR
O
Tracking servo drive PWM signal (+) output to the BH6511FS (IC501)
87
DVDD
—
Power supply terminal (+3.3 V) (digital system)
88
FFDR
O
Focus servo drive PWM signal (+) output to the BH6511FS (IC501)
89
FRDR
O
Focus servo drive PWM signal (–) output to the BH6511FS (IC501)
90
FS4
O
Clock signal (176.4 kHz) output terminal (X’tal system) Not used (open)
ZS-M30
Pin No.
Pin Name
I/O
Pin Description
91
SRDR
O
Sled servo drive PWM signal (–) output to the BH6511FS (IC501)
92
SFDR
O
Sled servo drive PWM signal (+) output to the BH6511FS (IC501)
93
SPRD
O
Spindle servo drive PWM signal (–) output to the BH6511FS (IC501)
94
SPFD
O
Spindle servo drive PWM signal (+) output to the BH6511FS (IC501)
95
FGIN
I (S)
96
TEST1
I
97
TEST2
I
98
TEST3
I
99
DVSS
—
Ground terminal (digital system)
100
EFMO
O
EFM signal output terminal when recording mode
Input terminal for the test (fixed at “L”)
* I (S) stands for schmitt input, I (A) for analog input, O (3) for 3-state output, and O (A) for analog output in the column I/O.
33
ZS-M30
• MD BOARD IC601 MD System control ( M30620MCA-A73FP )
Pin No.
Pin Name
1
LCD_DATA
—
Not used (OPEN)
2
LCD_CLK
—
Not used (OPEN)
3
LCD_CE
—
Not used (OPEN)
4
LCD_AO
—
Not used (OPEN)
5–7
8
BYTE
9
CNVss
10,11
I/O
Pin Description
—
Not used (OPEN)
—
Not used (OPEN) (connect to ground)
—
Ground terminal
—
Not used (OPEN)
12
SYS–RST
I
System reset input “L” reset
13
EXTAL
O
Main system clock output terminal (12MHz)
14
Vss
—
Ground terminal
15
XTAL
I
16
Vcc
—
Power supply terminal
—
Not used (fixed at “L” )
17
18
—
19
XINT
20
PDOWN
21
Main system clock input terminal (12MHz)
Not used (OPEN)
I
Sub system clock input terminal (32.768KHz)
I
Power down signal input from main system control (IC801)
—
Not used (OPEN)
22
LEO–0
—
Not used (OPEN)
23
LEO–1
—
Not used (OPEN)
24
LEO–2
—
Not used (OPEN)
—
Not used (OPEN)
25–30
31
SWDT
O
Writing data signal output to the serial bus
32
SRDT
I
Reading signal input from the serial bus
33
SCLK
O
Clock signal output to the serial bus
34
XLATCH
O
Latch signal output to the serial bus
35
TXD(UART)
I
Communication UART transfer input for main system control (IC801)
36
RXD(UART)
O
Communication UART receive output for main system control (IC801)
37
RTS(T)
I
UART transfer request input from master system control (IC801)
38
CTS(R)
O
UART transfer request output to master system control (IC801)
39,40
—
Not used (OPEN)
41
—
Not used (fixed at “L” )
42 – 45
—
Not used (OPEN)
46
—
Not used (fixed at “H” )
47– 50
—
Not used (OPEN)
51
A–MUTE
—
Not used (OPEN)
52
SDA
I/O
Serial data IN/OUT terminal for EEPROM (IC603)
53
SCL
O
Serial clock output terminal for EEPROM (IC603)
54
2654/2662
I
Destination select terminal
55
STB
O
Power ON/OFF control signal output
56
SCTX
O
shared with the magnetic head ON/OFF output
57
EMP
O
Diemphasis ON/OFF control signal output
58
DIG–RST
O
Reset signal output “L” reset
59
WRPWR
O
Write power ON/OFF output
60
DA–RST
O
Reset signal output to the D/A, A/D converter (IC604)
61
MOD
O
Laser modulation swithing signal output
62
Vcc
—
Power supply terminal
—
Not used (OPEN)
63
34
Writing data transmission timing output to the CXD2654R (IC504)
ZS-M30
Pin No.
Pin Name
I/O
64
Vss
—
65
SENS
I
Internal status (SENS) input from the CXD2654R (IC504)
66
FOK
I
Focus OK signal input from CXD2654R (IC504)
67
SHOCK
I
Track jump detection signal input from CXD2654R (IC504)
68
MNT2(XBUSY)
I
In the state of executive command from the CXD2654R (IC504)
69
MNT3(SLOCK)
70
71
LDON
72–73
Pin Description
Ground terminal
I
In the state of spindle servo lock from the CXD2654R (IC504)
—
Not used (OPEN)
O
Laser ON/OFF control output “H” : Laser ON
—
Not used (OPEN)
74
SQSY
I
ADIP sync or subcode Q sync input from the CXD2654R (IC504)
75
DQSY
I
Digital in sync input from the CXD2654R (IC504)
76–79
80
LDOUT
—
Not used (OPEN)
O
Loading motor control output
81
LDIN
I
Loading motor control input
82
LD LOW
O
Loading motor voltage control output Low voltage : “H”
83
REC P
I
Recording position detection switch (S502) input
84
PB P
I
Playback position detection switch (S504) input
85
LIMIT–IN
I
Limit switch (S681) input
86
PROTECT
I
Disc write protect detect switch (SW5) input
87
REFLECT
I
Disc reflection rate detection input from the reflect detection switch (SW5)
88
PAC–OUT
I
Pack out switch (S503) input
89
KYE0
—
Not used (OPEN)
90
KYE1
—
Not used (OPEN)
91
KYE2
—
Not used (OPEN)
92
JOG0
—
Not used (OPEN)
93
JOG1
—
Not used (OPEN)
—
Not used (OPEN)
94 –95
96
Avss
—
Ground terminal
97
Vref
—
Reference voltage input
—
Not used (OPEN)
—
Power supply terminal
—
Not used (OPEN)
98
99
100
Avcc
35
ZS-M30
• Circuit Board Location.
POWER BOARD
BATT (A) BOARD
BATT (B) BOARD
MAIN BOARD
TOP BOARD
SW (L) BOARD
JACK BOARD
LCD BOARD
TUNER BOARD
SW (R) BOARD
CD BOARD
REC BOARD
DETECT BOARD
D SW BOARD
MD BOARD
36
ZS-M30
6-2. BLOCK DIAGRAMS (1/4)
REC BOARD
(1/2)
CN602
2
MD BOARD
E
15
TX
FILO
ASYO
40
AUX
PEAK
3T
TEMP
B
38
57
PEAK &
BOTTOM
BOTM
ADIN
ADFG
19
11 BCK
10 LRCK
9 256FS
20
DIN
33
CLOCK
GENERATOR
SERIAL/PARALLEL
CONVERTER,
DECODER
LD
PD
APCREF
LASER DIODE
PD
V-I
CONVERTER
F0CNT
12
8
A00 – A09
MNT0
MNT1
MNT2
MNT3
SWDT
SCLK
XLAT
SRDT
SENS
14
9
5 6 7
1 2 3 4
75 74
19
65 32 31 33 34
64 67 68 65
16 17 18
56 SCTX
LD+3V
58 DIG-RST
61 MOD
59 WR-PWR
EXTAL 13
IN2F 29
92
IN2R 30
91
IN1F 19
IN1R 18
SFDR
IN3F 14
IN3R 15
27 OUT2F
M
SL-
TFDR
86
TRDR
85
IC602
LDIN
LDOUT
5
4
FIN
1
7
16
3
4
17
D
MAIN
BOARD
(2/2)
XOE
XWE
XRAS
XCAS
B+SWITCH
Q602,603
D+5V
X601
12MHz
STB 55
PODWN 30
PODWM
IC603
M+5V
DIGITAL SERVO
SIGNAL
PROCESS
DIGITAL SERVO
SIGNAL PROCESSOR
8
VCC 3
VREF 6
SCL 53
SDA(EEP) 52
REFERENCE
VOLTAGE SWITCH
Q601
82 LD-LOW
(LIMIT IN SW)
A/D CONVERTER
S501
85 LIMIT-IN
M
FROM CPU
INTERFACE
AUTO
SEQUENCER
8 OUT4R
SL+
IC601
ANALOG MUX
SRDR
FFDR
88
FRDR
89
LOADING
MOTOR DRIVE
AUX1
ABCD
FE
TE
SE
PEAK
BOTM
AUTOMATIC
POWER
CONTROL
67 65 66 75 74 63 64
OUT2
SPRD
13
WRPWR
OUT1
IN4F 4
10
XRST
6 OUT4F
M
SP-
M602
(SLED)
IN4R 3
SPFD
12 OUT3F
10 OUT3R
SP+
IC505
EEPROM
83
16
PSB
PWM GENERATOR
FCS–
TRK+
TRK–
D SW BOARD
M601
(SPINDLE)
21 OUT1F
23 OUT1R
D-RAM
17
AU3.3V
DARST 60
MD SYSTEM CONTROLLER
80 81
APCREF
FCS+
(FOCUS)
(TRACKING)
2-AXIS
DEVICE
16
+5V
M+5V
H+5V
Q508
FOCUS/TRACKING COIL DRIVE,
SPINDLE/SLED MOTOR DRIVE
IC501
B+SWITCH
Q605,606
XTAL 15
RIN
HF MODULE
SWITCH
Q501,502
Q504,505
MOD
MD-H
Q604(2/2)
GATE
X501
45.1584MHz
XOE
43
XWE
47
XRAS
46
XCAS
44
71 LDON
HF MODULE
Q604(1/2)
20
FOK
10
LD/PD
AMP
12 11
SHOCK
MNT2(BUSY)
MNT3(SLOCK)
LASER ON
SWITCH
Q503
APC
94 93
SCLK
XLAT
11
28
SWDT
AUTOMATIC
POWER CONTROL
Q506,507
26
MONITOR
CONTROL
SPINDLE
SERVO
SENS
PD
COMMAND
79
34
F0CNT
SRDT
LD+3V
SE
CPU
INTERFACE
35
XINT
TRACKING
ERROR AMP
78
XINT
TE
I-V
AMP
F
9
ILCC
FE
FOCUS
ERROR AMP
E
8
F
ABCD
ABCD
AMP
I-V
AMP
32
SQSY
C
D
E
30
SQSY
DETECTOR
29
DQSY
E
B.P.F.
INTERNAL BUS
DQSY
A
B
C
D
4
5
6
7
SUBCODE
PROCESSOR
ADIP
DEMODULATOR/
DECODER
SPRD
A
ADFM
SPFD
A
D
AT
AMP
ADFG
J
EQ
3T
WBL
B
C
MAIN
BOARD
DA-RCH
(1/2)
A/D,D/A
CONVERTER
OSCO
36
SWDT
SCLK
XLAT
C
AD-RCH
IC604
OSCI
37
CD
BOARD
REC-H
21
WBL
I
A/D
15
DADT
26
XBCK
28
LRCK
27
FS256
29
COMPARATOR
RFI
DIN
23
14 1 2 24
ASYI
EQ
WBL
B.P.F.
F
RF
DOUT
DA-LCH
1, 2, 18, 19
46
RF AGC
& EQ
DIN1
VOUTL
19
VOUTR
20
PDDA
8
DQ1 – DQ4
RF AMP
AGCI
DIN0
DIGITAL
AUDIO
INTERFACE
24
A0 – A9
RFO
LRCKI
A/D
22
VDD
VCC1
VCC1
VCC2
PLL
XBCKI
DOUT
AD-LCH
6 – 9, 11 – 15,5
54
J
2
CLTV
IC502
I
1
J
53
PCO
12
D0 – D3
I
MORFI
MORFO
OPTICAL PICK-UP
(KMS-260B)
RF AMP,
FOCUS/TRACKING ERROR AMP
47
62
61
IC504 (1/2)
48
59
SAMPLING
RATE
CONVERTER
25
6
3
7
49, 48, 50, 51
FILTER
DIGITAL SIGNAL PROCESSOR,
EFM/ACIRC ENCODER/DECODER,
SHOCK PROOF MEMORY CONTROLLER,
ATRAC ENCODER/DECODER
DADT
VINL
VINR
PDAD
34 – 31, 36 – 40, 45
60
SCTX
ADDT
ATRAC
ENCODER/DECODER
HR901
OVER WRITE HEAD
EFMO
FILI
SHOCK PROOF
MEMORY CONTROLLER
100
IC503
EFM/ACIRC
ENCODER/DECODER
OVER WRITE
HEAD DRIVE
HEAD
DRIVER
Q509,510
1
IC151 (1/2)
M103
(LOADING)
XLRF
XLAT
80
CKRF
SCLK
81
DTRF
SWDT
82
87 REFLECT
86 PROTECT
6 SCL
5 SDA
B+SWITCH
Q607
BU3.3V
RXD(UART) 36
TXD(UART) 35
STXD
SRXD
RTS(L) 37
CTS(R) 38
SCTS
SRTS
PAC-OUT 88
SYS-RST 12
REC-P 83
PLAY-P 84
PACKIN
MDRST
S502 (REC P)
S504 (PLAY P)
S503
(OUT)
IC504 (2/2)
• RCH
25 OUT2R
REC BOARD
(2/2)
SW5
PROTECT/REFLECT
37
37
DETECT
BOARD
: Same as LCH
• SIGNAL PATH
: MD (PLAY)
: MD (REC)
ZS-M30
6-3. BLOCK DIAGRAMS (2/4)
CD BOARD
IC701
HI-SPEED
VCC
A
4
A
C
1
B
D
5
10K
RAM
RFM 14
VC
4
PD1
C
D
5
RF
SUMMING
AMP
PD2
B
2
DIGITAL SERVO
DIGITAL SIGNAL PRCESSOR
SWITCH
6
E
IC702
Q703
RF AMP
DETECTOR
RF EQ
AMP
RFO
RF AC
15
EFM
DEMODULATOR
51
RF-I 16
FE
FOCUS
ERROR
AMP
15
INTEGRATOR
49
ASYI
ASYMMETRY
CORRECTION
8
7
TE
TRACKING
ERROR
AMP
F
11
X701
33.8688MHz
67
LD
DRIVE
Q101
LD
2
66
VC
BUFFER
LD
LMUT
AIN1
AOUT1
DIGITAL
CLV
3rd ORDER
NOISE
SHAPER
PWM
PWM
CONTROL SIGNAL
BLOCK
3
PD
18
VC
AOUT2
LDON
43
39
19
41
IC703
42
FOCUS/TRACKING COIL DRIVE
SPINDLE/SLED MOTOR DRIVE
T+
T
F
SL+
14
2
SP+
CE
MIRR
DFCT
FOK
OP AMP
A/D
ANALOG SW CONVERTER
SERVO
AUTO
SEQUENCER
SE
PWM
GENERATOR
TRDR
30
18
31
24
23
FRDR
32
12
11
5
6
TFDR
TRDR
FFDR
33
SFDR
28
SRDR
29
FFDR
FRDR
SFDR
SRDR
FOCUS
PWM
GENERATOR
FOCUS
SERVO
SLED
PWM
GENERATOR
SLED
SERVO
LOUT
72
71
70
75
A
MAIN BOARD
(2/2)
ROUT
37 NC
XLAT
7
CLK
20
SCOR
1
SQSO
SQCK
2
SYSM
4
SQCK
SQSO
MAIN BOARD
(1/2)
76
DATA
SCOR
B
77
6
CLK
CPU
INTERFACE
79 NC
80 NC
5
XLAT
SSTP
TRACKING
SERVO
19 NC
SENS
SERVO DSP
TRACKING
PWM
GENERATOR
61 NC
AU3.3V
27
S702
LIMIT SW
SERVO
INTERFACE
SCLK
9
SCLK
RF-H
SP-H
XRST 3
XRST
AGC CONT
XLON
14
15
M
SP
40
DETECTOR
FE
TE
63 NC
8
DATA
RFDC
TFDR
17
M
SL
Q702
SENS
13
3
F+
INTEGRATOR
XTSL
SERVO
BLOCK
38
APC LD
AMP
LD
POWER
M901
SPINDLE
MOTOR
RMUT
LOUT2
AGC CONT
M902
SLED
MOTOR
C2PO
AIN2
PD
FOCUS
COIL
LRCK
10
LASER
DIODE
TRACKING
COIL
D/A
INTERFACE
DIGITAL
FILTER
CLOCK
GENERATOR
MD BOARD
62 NC
SERIAL IN
INTERFACE
XTAO
XTAI
E
PCMD
LOUT1
E
CN703
1
60
3 NC
ASYO
F
D OUT
2
DIGITAL
PLL
48
E
ERROR
CORRECTOR
DIGITAL
OUT
BCLK
SUB CODE
PROCESSOR
F
10
REGISTER
DATA BUS
OPTICAL PICK-UP BLOCK
(KSS-213C)
16
26
25
SPIN
SPEED SW
Q705
26
MDP
NC
• SIGNAL PATH
Q707
MUTE 20
: CD
MUTE
: MD (REC)
38
38
ZS-M30
6-4. BLOCK DIAGRAMS (3/4)
B+(5V)
TUNER BOARD
L6
FM IF
FM/AM FRONT-END,
IF, DET, FM MPX
ANT1
FM
TELESCOPIC ANTENNA
IC1
AM MIX-OUT
32
D7
CT3
LW
TRACKING
CT2
MW
TRACKING
D6
7
23
22
MP
IN
12
FM
MPX
MUTE
13
AM
IF-IN
R-CH
• SIGNAL PATH
AM
DET
: FM
: AM
IF
BUFFER
5
CF3
FM
OSC
DET-OUT
R-CH : Same as L-CH.
L3
RF AMP
Q1
1
AM RF-IN
AM
MIX
L3
MW
TRACKING
D3
L4
LW SWITCH
Q3
OSC
DO
18
CL
17
DI
16
CE
15
PLL
L4
LW
TRACKING
MW SWITCH
Q2
XOUT
30
Q6
L5
MW
FREQUENCY
COVERAGE
CT4
LW SWITCH
Q4
TU CONT
TU CLK
TU DATA
TU CE
CONTROL
Q5
CT4
LW
FREQUENCY
COVERAGE
FM
DET
B+(5V)
CT2
CT3
FM
IF-IN
29
L5
MW/LW
OSC
31
20
MW
XIN
LW
AM OSC
AM
OSC
G
MAIN
BOARD
(2/2)
X1
75kHz
19
P-IN
MW/LW
ANTENNA
D8
FM OSC
L2
FM
OSC
B+ (5V)
D9
8
T1
AM IF
B+ (5V)
TB1
CF2
FM RF OUT
L1
FM
RF
CT1
D2
CF1
3
AM/FM
BUFFER
34
D1
FM MIX-OUT
FM
MIX
L1
FM
TRACKING
CT1
FM
TRACKING
D4
FM RF-IN
P-OUT
D5
36
FM DET
FL1
B.P.F
11
28
27
B+(5V)
VT(+7.5V)
NC
NC
NC
MAIN BOARD (1/2)
J302
LINE
14
R-CH
13
MUTE
Q111
12
11
R-CH
17
AD LCH
17
20
MD R-CH
L1
LIN
MEGA BASS AMP
LOUT
AMP
5
5
RSELO
L4
21
22
ROUT
RIN
AMP
26
R-CH
VCC 4
7
R-CH
L3
11
OUT1
Q310
R1
POWER AMP
R-CH
MAIN BOARD
(2/2)
SP101
MAIN SPEAKER
(L-CH)
R2
R3
VCC 4
CONTROL
R4
11
MD R-CH
2
1
IN1
MUTE
Q106
CL
VCC
H
i
5
STBY 8
OUT1
UNREG 14V
SP201
MAIN SPEAKER
(R-CH)
5
STBY 8
SP102
PANORAMA SOUND
(L-CH)
Q302
30
R-CH
MUTE DRIVER
Q313,312
SP202
PANORAMA SOUND
(R-CH)
R-CH
COM7V
CD R-CH
AUDIO LEVEL
DETECT
D101,201,301
LINE MUTE
J301
R-CH
MUTE
Q101
Q102
CD LOUT
CD ROUT
IN1
UNREG 14V
IC303
29
B
9
POWER AMP
IC305
DA LCH
DA RCH
CD BOARD
LTRE
10
L2
DI
C
18
LSELO
CE
MD BOARD
AD RCH
8 7 6
IC302
INPUT SELECT
LBASS1
LBASS2
JACK
BOARD (1/2)
JACK
BOARD (2/2)
IC301
R-CH
Q305
R-CH
HP-SW
PA-STANDBY
AU-CS
SUR
AU-DATA
MEGA BASS
AU-CLK
A-MUTE
39
39
I
MAIN
BOARD
(2/2)
ZS-M30
6-5. BLOCK DIAGRAMS (4/4)
MAIN BOARD (2/2)
MAIN
BOARD
(1/2)
MAIN
BOARD
(1/2)
H
I
LINE MUTE
AU-CS
AU-DATA
AU-CLK
33
23
24
25
LINE MUTE
AU-CS
AU-DATA
AU-CLK
HP-SW
PA-STANDBY
22
31
35
21
14
HP-SW
PA-STANDBY
SUR
MEGA BASS
A MUTE
TU-CONT
TUNER BOARD
G
100
99
98
97
TU-CLK
TU-DATA
TU-CE
BU3.3V
AU3.3V
D+5V
SUR
MEGA BASS
TOP BOARD
A MUTE
MD+5V
D403
PANORAMA
SOUND
TU-CONT
TU-CLK
TU-DATA
D402
HI-SPEED
LED-SURROUND2 37
LED-HISPEED2 36
TU-CE
BU3.3V
AU3.3V
D+5V
KEY AD0 56
KEY AD0
S401-405
STXD
PDOWN
69 MD-SRXD
70 MD-STXD
1 MD-PDOWN
SRTS
PACK IN
SCTS
MDRST
MD-H
REC-H
2
3
4
5
6
7
MD-SRTS
MD-PACK IN
MD-SCTS
MD-RST
MD-H
REC-H
SP-H
RF-H
AGCCONT
SCLK
SCOR
SENS
SQSO
SQCK
XLAT
CLK
DATA
XRST
66
80
67
68
78
77
79
81
74
73
75
76
CD-SPH
CD-RFH
CD-AGCCONT
CD-SCLK
CD-SCOR
CD-SENS
CD-SQSO
CD-SQCK
CD-XLAT
CD-CLK
CD-DATA
CD-XRST
SRXD
MD BOARD
CD BOARD
D
A
S701
(CD DOOR OPEN/CLOSE)
KEY AD1 55
S406-410
KEY AD2 61
B+
(COM 7.5V)
IC801
KEY AD3 60
JOG-B 57
JOG-A
SW(L)BOARD
B+
(CD 3.3V)
B +5V
(MD)
B+
(BU 3.3V)
XTAL
EXTAL
TU SFT
BU3.3V
86
87
42
43
39
X801
32.768kHz
X802
8MHz
3
B +5V
REG
B+
(MD 5V)
1
RESET
2
3
IC506
D911
J901
- AC IN
F902
1.6A
MD +5V
REG
1
IC802
BU +3.3V
3
2
REG
D802
IC803
P-CON 85
CD POWER
CD-POWER 64
IC804
LF901
D910
D806
SW(R)BOARD
1
F901
3.15A
CD POWER
P-CON
RST 40
+7V
REG
Q810
B+
(CD 7V)
CD POWER
SWITCH
Q806,807
IC401
38 VDD-CONT
RECT
D905-908
P-CON
REMOTE
CONTROL
1 RECEIVER
RMC
B+
(UNREG 10V)
POWER
SWITCH
Q808,809
REG
SWITCH
Q816,817
1
93 B/L-CONT
B/L VCC
B+SWITCH
Q812
+7.5V
REG
Q804
S411
S425
(JOG)
. >
2
JOG-B
RMC 85
45 LCD-STB
TX
BU3.3V
+3.3V
REG
Q805
KEY AD4
46 LCD-DATA
+7V REG.
Q811,
Q818,819
S412
S417-419,
S421,422
TTEX
B/L
VDD
(+7V)
B+
(COM 3.3V)
S423
KEY AD4 59
T901
POWER
TRANSFORMER
RECT
D901-904
S424
47 CD-CLK
LCD-STB
B+
(UNREG 14V)
S413-416
S420
MASTER
CONTROL
JOG-A 58
LCD-DATA
B+
(MD 5V)
POWER BOARD
B/L VCC
KEY AD3
84 CD-DOOR
LCD-CLK
PL404,405
LCD
BACK
LIGHT
KEY AD2
KEY
CONTROL
Q401
LCD
BOARD
LCD1
LCD
UNIT
KEY AD1
B+
(BU 3.3V)
AC
CHECK
Q802
ACCHK 94
LEVEL
SHIFT
Q801
40
40
B+(BL VCC)
BATT(A)BOARD
DRY BATTERY
SIZE "AA"
(IEC DESIGNATION R6)
3PCS,4.5V
(FOR MEMORY BACK-UP)
BATT(B)BOARD
ZS-M30
6-6. PRINTED WIRING BOARDS – MAIN SECTION –
3
2
4
MAIN BOARD
–
–
+
+
JW809
JW807
C120
R219
C123
C220
C304
C122 C222
R118
C130
R104
C103
R325
R220
R120
R202
C203
5 8
IC305
R119
JW806
R128
R101
R228
R102
C104
JW813
C223
R306
JW801
Q302 Q101
R314
JW805
JW803
JW845
JW804
IC301
C225
JW861
JW888
IC802
JW897
JW898
JW896
C864
JW820
JW816
D802
R857
D806
FB823
Q818
C821
R454
Q819
D811
Q811
R455
JW892
JW876
R883 R884
C810
R452
JW879
FB827
CN811
FB828 FB829
JW877
FB830
JW893
R459
C823
C822
Q810
JW875
Q817 Q816
C820
R899
FB814
FB819
R805 FB808
FB821
C846
C832
R806
C829
JW881
C827
R451
G
F
JW891
C881
Ref. No.
Location
D101
D201
D301
D802
D803
B-5
C-5
B-6
F-7
C-7
D804
D805
D806
D811
IC301
D-5
G-4
F-7
G-8
D-8
IC302
IC303
IC305
IC801
IC802
C-4
A-8
B-6
E-5
F-9
IC803
IC804
Q101
Q102
Q106
F-6
F-6
C-8
B-5
B-7
Q111
Q201
Q202
Q206
Q211
B-3
B-7
B-5
B-7
B-3
Q302
Q305
Q310
Q312
Q313
C-7
C-8
C-7
B-3
B-3
Q801
Q802
Q804
Q805
Q806
D-5
F-6
C-7
D-5
E-4
Q807
Q808
Q809
Q810
Q811
F-4
D-7
A-7
G-4
G-7
Q812
Q816
Q817
Q818
Q819
E-4
G-5
G-5
G-7
G-7
FB831
JW895
(MD CHASSIS)
JW890
1-679-399-
H
Semiconductor
Location
JW899
CN805
S701
(CD DOOR OPEN/CLOSE)
MD BOARD
CN603
R860
R862
R859
R893
R846 R855
R847
R848
R851
R850
R856
R853
IC803
R858
R854
CH802
C818
JW872
FB817
FB818 C882
FB812
FB815 FB813
FB807 FB809
R807 R809
R808
R813
R812
R811
R898
FB816
FB810
FB806
FB811
D804
R814
C847
R890
R839
R843
R844
R845
C861
JW871 C862
JW870
C869
JW867
JW869
JW873
D805
C819
JW866
R878
JW868
R821
R863
R822
C849
C848
JW860
R874 R894
R865
R886
JW849
JC804 R867
R866 JW859
JW864
JW865
JW863
JW862
C853
R831
R825
JW858
R824
C854 JW848
R832
C804
C801
JW850
C850
R424
R425
C407
H
CD BOARD
CN702
Q305
D803
R309
R319
C115
C116
R873
JW839
R457
R456
JW840
R111
C117
JW821
R203
R426
R429
R320
R324
C114
R428
R430
R427
Q206
R218
R302
R226
R312 R221 D201
C308
C124
Q106
4 1
D301
C319
R303
R318
R110
D101
R125
R123
R217
C111
I
F
R207
C306
C310
C230
R201
C811
JW822
C813
C311
Q310
JW823
CN807 C879
JW825
FB880
JW815 R326
JW842
JW824
R122
C883
C113 C126
C112
JW843
JW826
R304
JW827
FB802
R117
JW844
PL404
JW828
JW802
R103
C118
(BACK LIGHT)
JW830
R124
C816 Q805
C129
FB803
R216
Q804
JW829
C814
C102
JW831
JW332
R212
JW832
C202
R112
JW331
Q809
JW833
C125
JW315
JW834
R116
JW314
C309
R885
JW836
JW835
R323
R891
FB820
R864
JW313
Q808
C840
C838
R115
C805
C839
JW312 JW855
Q801
C835
R826
C105
C119
JW856
C806
C219
C836
CN804
C877
JW330
C803
R215
C865
JW319
JW311
31
R887
JW308
JW889
C205
JW310
X802
Q812
R829
JW894
JW309
JW847
R823
R804
JW307
C834
R453 R803
CN404
C833
R802
CN812
R827
R801
JW305
R875
C831
R820
1
PL405
IC801
JW306
51
R868
R819
Q806
(BACK LIGHT)
JW304
R818
JW857
C855 R833
C844
C303
R869
C845
JW887
R834
R817
R870
C863
C843
C817
R835
R861
C856
R816
JW886
R836
Q807
JW885
CN808
R837
C857
81
Q802
JW321
C878
C842 JW884
21
X801 C808
R892
(21)
JW880
JW838
1-679-400C870
C825
C807
JW883
C859
R852
SW (R) BOARD
R881
C828
JW878
IC804 JW882
CN402
R841
R882
JW301
R842
123
JW874
123
LCD BOARD
E
C208
R105
C108
JW814
C107
JW324
C216
C215
IC302
C204
R206
Q202
R107
R108 Q102
Q201
R204
C323
R208
C224
LCD1
LIQUID
CRYSTAL
DISPLAY
R205
R106
C106
C217
C101
POWER BOARD
CN901
IC303
JW811
JW810
C221
R210
C207
JW323
C121
R126
C213
C201
R211
C214
D
CN801
R225
JW817
D
JACK BOARD
CH306
C218 CN302
C212
Q313
C
10
CN810
CN303
C226
R327
C211
C110
Q312
R328
Q111
B
9
z
C206
C326
Q211
JW819
JW818
TOP BOARD
CN401
R114
R113
R214
R213
R223
R222
C210
R224
C229
6
A
C
8
7
CN301
CN803
JACK BOARD
CH302
6
SP202
PANORAMA
SOUND (R-CH)
JW322
B
A
5
SP102
PANORAMA
SOUND (L-CH)
R121
1
21
(21)
G
TUNER BOARD
CN1
41
NOTE:
• X : parts extracted from the component side.
• b : Pattern of the rear side.
41
ZS-M30
6-7. SCHEMATIC DIAGRAM – MAIN SECTION (1/3) –
z
Refer to page 55 for Notes.
z
Refer to page 58 to 61 for IC Block Diagrams.
42
42
z
Refer to page 56 for Waveforms.
ZS-M30
6-8. SCHEMATIC DIAGRAM – MAIN SECTION (2/3) –
z
Refer to page 55 for Notes.
z
Refer to page 58 to 61 for IC Block Diagrams.
43
43
ZS-M30
6-9. SCHEMATIC DIAGRAM – MAIN SECTION (3/3) –
z
Refer to page 55 for Notes.
z
Refer to page 58 to 61 for IC Block Diagrams.
44
44
ZS-M30
6-10. PRINTED WIRING BOARDS – POWER SECTION –
3
2
1
4
5
POWER BOARD
A
6
BATT (B) BOARD
J901
- AC IN
7
BATT (A) BOARD
JW405
LF901
JW404
JW406
B
RED
JW407
WHT
T901
POWER TRANSFORMER
JW403
* NOT REPLACEABLE:
BUILT IN TRANSFORMER
1-679-405-
*
C
21
(21)
1-679-404-
JW402
21
21)
DRY BATTERY
SIZE "AA"
(IEC DESIGNATION R6)
3PCS, 4.5V
(FOR MEMORY BACK-UP)
z
Semiconductor
Location
Ref. No.
D
D904
D908
6
C902
D901
E
F901
D903
D911
D906
R902
D905
R901
D910
C905
CN901
C901
C906
CN902
RED
D907
F902
C904
C903
D902
Location
D901
D902
D903
D904
D905
E-2
E-2
E-2
D-2
E-3
D906
D907
D908
D910
D911
E-3
E-3
D-3
E-3
E-3
1-679-40621
(21)
D
NOTE:
• X : parts extracted from the component side.
• b : Pattern of the rear side.
MAIN BOARD
CN801
45
45
ZS-M30
6-11. PRINTED WIRING BOARDS – TUNER SECTION –
3
2
1
4
z
ANT1
FM
TELESCOPIC ANTENNA
Ref. No.
D1
D2
D3
D4
D5
TB1
MW/LW ANTENNA
A
R17
R9
C23
L6
R34
R36
R33
C25
R22
R19
R23
R21
R35
CN1
C15
JW14
R24
C39
C38
R18
C20
R10
R25
R26
C17
C41
R8
JW13
C16
JW17
R15
C33
R16
C19
C2
C18
CF2
CF3
CF1
C13
T1
C40
R11 C21
JW11
E
C28
JW16 C37
C22
JW12
C14
C24
C32
L8
D1
CT1
R32
C50
C1
C30
IC1
B-3
B-3
B-3
B-3
D-3
IC1
Q1
Q2
Q3
Q4
D-2
B-1
B-2
B-2
C-3
Q5
Q6
C-4
C-3
NOTE:
• X : parts extracted from the component side.
•
f
: internal component.
•
x
: parts mounted on the conductor side.
• b : Pattern of the rear side.
C29
C36
X1
C3
D
JW5
JW4
R7
R27
L1
Q5
Q6
R13 C26 R14 C27
R12
D6
D7
D8
D9
D10
C52
Q4
L5
R2
C49
C11
C12
Location
D-1
C-2
B-3
B-2
B-2
C43 JC2
C34
C35
JW10
JW8
R3
JW9
R29
C47
D10
R28
CT3
R30
R4
C5
C6
C4
C44
FL1
R1
D2
C51
Q1
L2
C45
C
R31
Q3
C53
JW6
C9
CT2
Q2
CT4
R5
C46
L4
C10
C8
D3
JC3
JW7
C7
L3
R6
JW3
JW2
C60
D5
L7
B
D6
D4
D7
D8
D9
TUNER BOARD
JW1
Semiconductor
Location
R20
11
(11)
1-681-053-
G
MAIN BOARD
CH802
46
46
ZS-M30
6-12. SCHEMATIC DIAGRAM – TUNER SECTION –
z
Refer to page 55 for Notes.
z
Refer to page 58 to 61 for IC Block Diagrams.
47
47
z
Refer to page 56 for Waveforms.
ZS-M30
6-13. PRINTED WIRING BOARDS – CONTROL SECTION –
3
2
1
4
TOP BOARD
5
6
8
7
9
F
z
A
R406
S403
SYNCHRO REC
CDBMD
D402, S402
HIGH SPEED
S404
S405
R407
STANDBY
REC
REC MODE
S410
SOUND
MEGA BASS
S408
MODE
Ref. No.
R410
R405
D403
S409
D402
S402
6
CN401
D403, S409
R411 PANORAMA
SOUND
S407
VOLUME–
R409
A
MAIN BOARD
CN803
S406
VOLUME+
R408
S401
OPERATE
R404
B
1-679-401-
–
+
CH306
1
S411
MD
u
S424
MD
R419
Z
R414
S415
RADIO BAND
AUTO PRESET
S414
CD
x
S413
CD
u
1-679-403-
MAIN BOARD
CN303
R431
21
(21)
S420
EDIT
R418
CH401
R417
B
1-679-407-
21
(21)
IC401
CN402
E
3
S412
MD
x
MAIN BOARD
CN301
21
(21)
A-7
E-8
C-8
R415
D307
D306
J302
L302
CH402
R416
C
FB202
CH302
R413
D403
Q401
IC401
SW (R) BOARD
L301
D308
D309
FB102
SP201
MAIN
SPEAKER
(R-CH)
S416
(GAME)LINE
LINE LEVEL
D-3
D-3
D-2
D-2
A-3
S423
NO
CANCEL
I
MAIN BOARD
CN804
S422
YES
ENTER
Q401
R423
BLK
BLU
JW317
JW316
L201
D
R227
J302
LINE IN
+
WHT –
CN304
J301
i
RED
Location
D306
D307
D308
D309
D402
R412
JW318
L101
R127
C
SW (L) BOARD
SP101
MAIN
SPEAKER
(L-CH)
C401
JACK BOARD
Semiconductor
Location
C403 C402
S418
TUNE+
Mg
S419
TUNE–
Gm
R420
F
S417
DISPLAY
S425
(JOG)
. >
R421
1-679-402G
R422
S421
DEL
CLOCK/SLEEP/TIMER
21
(21)
NOTE:
• X : parts extracted from the component side.
• b : Pattern of the rear side.
48
48
ZS-M30
6-14. SCHEMATIC DIAGRAM – CONTROL SECTION –
z
Refer to page 55 for Notes.
49
49
ZS-M30
6-15. PRINTED WIRING BOARDS – CD SECTION –
3
2
1
4
5
6
8
7
H
CD BOARD
MAIN BOARD
CN808
z
Semiconductor
Location
Ref. No.
A
FB706
C746
FB705
M902
SLED MOTOR
Location
IC701
IC702
IC703
Q701
Q702
E-3
D-5
B-2
E-4
D-5
Q703
Q705
Q707
D-1
B-3
B-4
JW713
TP
(RF)
R725
R710
C731
JC701
L702
C730
C727
C726
C723
C714
C722
R786
TP
(VC)
R708
R713
R714
R715
R716
C721
R718
R719
C712
C707
C717
1-679-411-
F
MD BOARD
CN602
C701
R721
R717
C716 TP(TE)
C715
R732
C706
C761
JW701
Q702
JW720
JW734
C708
E
JW728
JW726
JW724
C711
C704
R709
R791
CN703
JW719
JW715
JW727
E
C733
R720
Q701
JW706
JC708
C720
41
R783
JW723
IC701
JW708
JW703
JW702
R706
C703
JC721
C734
R722
JW710
JW722
C702
X701
JW716
JW721
JW717
R762
R701
JC722
R707
R705
C781
C705
21
R761
JC720
61
IC702
R759
JC707
Q703
R704
C762
R703
R724
R702
CN701
JW704
M
R790
1
R788
C732
R760
JW718
M901
SPINDLE MOTOR
D
C737
JW711
C757
S702
(LIMIT)
C760
L701
JC703
JW730
JC711
C758
JW714
JC712
C741
C740
C743
JW725
C738
C764
R723
R726 C739
C729
C765
R787
C
R728
JW729
C766
R727
FB703
R776
R729
R779
JW705
R736
R735
FB704
C768
R774
R785
R730
R751
C713
R750
C710
R731
R712
C744
R799
JW732
Q705
C759
IC703
R780
Q707
JW733
B
R782 JW709
R775
JW712
R781
M
JW707
R777
CN702
11
(11)
OPTICAL PICK-UP
BLOCK
(KSS-213C)
NOTE:
• X : parts extracted from the component side.
• b : Pattern of the rear side.
50
50
ZS-M30
6-16. SCHEMATIC DIAGRAM – CD SECTION –
z
Refer to page 55 for Notes.
z
Refer to page 58 to 61 for IC Block Diagrams.
51
51
z
Refer to page 56 for Waveforms.
ZS-M30
6-17. PRINTED WIRING BOARDS – MD SECTION –
8
90
35
85
IC504
80
60
50
45
R633
R629
R631
G
IC603
C621
Q603
FB628
C533
L510
R611
R534
R616
IC503
Q509
CN504
1
R605
C613
11
(11)
M601
M SPINDLE
SW5
(PROTECT/REFLECT)
MOTOR
M
1-677-526-
1-679-413-
Q510
I
F-11
B-5
B-3
C-3
F-2
IC602
IC603
IC604
Q501
Q502
A-5
G-3
A-3
F-4
F-4
Q503
Q504
Q505
Q506
Q507
F-5
F-4
F-4
F-5
F-5
Q508
Q509
Q510
Q601
Q602
G-5
I-5
I-4
B-5
D-10
Q603
Q604
Q605
Q606
Q607
C-10
B-10
A-10
A-10
F-1
Caution:
Pattern face side: Parts on the pattern face side seen from the
(Side B)
pattern face are indicated.
Parts face side: Parts on the parts face side seen from the
D SW BOARD
C562
D502
D503
IC503
IC504
IC505
IC506
IC601
NOTE:
• X : parts extracted from the component side.
•
a
: Through hole.
• b : Pattern from the side which enables seeing.
(The other layers’ patterns are not indicated.)
C612
R601
R603
C606
JC601
R608
JC602
R607
R604
C608
C601
R627
R635
R606
R620
R619
C503
1-679-412-
HR901
OVER
WRITE
HEAD
R560
C563 C564
JC509
C565
L513
S504
(PLAY POSITION)
Q602
L603
C515
C524
C510
L502
11
(11)
4
E-7
I-5
I-5
E-9
E-5
R637
REC BOARD (SIDE A)
R561
Q605
L610
C627
FB507
C509
R602
C536
CN108
1-679-414-
C530
C501
C602
R506
C561
S504
R625
21
C537
5 7
11
(11)
S502
(REC POSITION)
L504
L505
1
S503
(PACK OUT)
CN503
C516
TP502
R511
(I+3V)
TP503
(IOP)
L506
1-679-412-
CN505
C531
IC501
CN501
C511
C506
S502
H
JC501
OPTICAL
PICK-UP
BLOCK
(KMS-260B)
R503
R504
Q503
C512
REC BOARD (SIDE B)
DETECT BOARD
FB621
L602
R524
R516
D501
R512
C528
R535
C518
C505
C517
R630
R515
Q506
Q508
40
1012
R514
L501
C611
35
R508
51
31
5
R502
R510
C508
30
15
13
S501
(LIMIT)
L604
R540
C550
55
C521
20
45
48
1
C523
R519
24
Q507
Q505
25
Q607
Q502
60
L503
R639
Q504
65
R505
15
JC506
L508
C526
R513
70
IC601
C607
X601
R621
75
R661 20
R638
R632
Q501
5
C604
10
R628
F
R531
C502
R622
R641
R642
C514
C520 C522
3635 30 25
37
IC502
C519 40
80
L608
L512
TP506
(VC)
R509
81
85
L611
JC502 L507
L511
TP505
(RF)
R517
90
95
1
C609
C546
R518
C603 100
MAIN BOARD
CN807
L612
JC505
C539
R542
TP504
(TE)
R614
FB601
E
F
5
C556
C534
R538
C513
JC603
R612
R613
R660
R659
FB602
L509
R526
FB603
R610
15
10
C559
R532
C552
C525
R609
FB614
R617
20
FL611
JC511
R541
C553
R549
R655
R618
JC510
Location
D501
D502
D503
IC501
IC502
22
L613
C560
C558
C540
JC605
D
FB627
FB625 FL612
R539
M103
LOADING
MOTOR
C527
CN603
1
JC516
FB613
75
R646
1
CN601
C547
FB617
JC503
IC506
70
C551
C554
JC508
65
R544
R654
R656
C629
7
M
C529
76
R553
R551
C549
C541
1
JC504
1
C545
C544
C542
81
45
51 55
2
3
R658
30
C626
Q604
X501
C538
100
50
20
CN502
5
C548
R521
R528
JC514
L605
FB624
FB629
FB616
FB615
FB619
FL609
5
L606
C555
1
26
40
16
R651
Semiconductor
Location
Ref. No.
Q606
C532
6
IC505
JC512
FB626
JC507
C631
C
R562
10 5
15
R522 R523
15
FL606
FL602
20
25
10
R520
R527
11
R530
R640
FL601
R547
R559
R652
R501
FB501 R555
C557
Q601
R537 R536
12
C623
R653
C632
R548
C633
FB508
R529
JC604
R626
R550 R545
R556
R558
FB505
FB506
FB502
R643
R644
FB612
FB611
FL605 FB618
C620
C614
L607
FB620
L601
R543
FL610
C624
(CHASSIS)
FL607
R624
FL503
FL608
11
z
CN602
IC602
R623
IC604
C610
R552
FL502 FB504
FB606
FB503
FB610
R557
R554
FL501
R525 R533
C625
R649
FB605
FL603
FL604
R650
C619
R648
FB607
FB609
FB623
B
R647
FB604
FB622
A
E
MD BOARD (SIDE A)
10
C622
MD BOARD (SIDE B)
9
CD BOARD
CN703
C615
7
C616
C630
6
R645
5
C618
C617
4
C605
3
2
1
11
(11)
1-679-413-
52
52
11
(11)
11
(11)
M602
SLED
MOTOR
ZS-M30
6-18. SCHEMATIC DIAGRAM – MD SECTION (1/2) –
z
Refer to page 55 for Notes.
z
Refer to page 58 to 61 for IC Block Diagrams.
53
53
z
Refer to page 57 for Waveforms.
ZS-M30
6-19. SCHEMATIC DIAGRAM – MD SECTION (2/2) –
z
Refer to page 55 for Notes.
z
Refer to page 58 to 61 for IC Block Diagrams.
54
54
z
Refer to page 57 for Waveforms.
ZS-M30
Note on Schematic Diagram: MAIN SECTION (1/3)
• All capacitors are in mF unless otherwise noted. pF: mmF 50 WV
or less are not indicated except for electrolytics and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise specified.
• A : B+ Line.
• Voltages and waveforms are dc with respect to ground under nosignal (detuned) conditions.
no mark: FM
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production tolerances.
• Circled numbers refer to waveforms.
Note on Schematic Diagram: MAIN SECTION (2/3)
• All capacitors are in mF unless otherwise noted. pF: mmF 50 WV
or less are not indicated except for electrolytics and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise specified.
Note: The components identified by mark ! or dotted line with
mark ! are critical for safety.
Replace only with part number specified.
• A : B+ Line.
• Voltages and waveforms are dc with respect to ground under nosignal (detuned) conditions.
no mark: FM
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production tolerances.
Note on Schematic Diagram: MAIN SECTION (3/3)
• All capacitors are in mF unless otherwise noted. pF: mmF 50 WV
or less are not indicated except for electrolytics and tantalums.
• All resistors are in W and 1/4 Ω or less unless otherwise specified.
• A : B+ Line.
• Voltages and waveforms are dc with respect to ground under nosignal (detuned) conditions.
no mark : FM
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production tolerances.
• Signal path.
F : FM
Note on Schematic Diagram: TUNER SECTION
• All capacitors are in mF unless otherwise noted. pF: mmF 50 WV
or less are not indicated except for electrolytics and tantalums.
• All resistors are in Ω and 1/4 Ω or less unless otherwise specified.
•
f : internal component.
• A : B+ Line.
• H : adjustment for repair.
• Voltages and waveforms are dc with respect to ground under nosignal (detuned) conditions.
no mark: FM
(
) : MW
<
> : LW
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production tolerances.
• Circled numbers refer to waveforms.
• Signal path.
F: FM
f: AM
Note on Schematic Diagram: CONTROLSECTION
• All capacitors are in mF unless otherwise noted. pF: mmF 50 WV
or less are not indicated except for electrolytics and tantalums.
• All resistors are in Ω and 1/4 W or9Uss unless otherwise specified.
• A : B+ Line.
• Voltages and waveforms are dc with respect to ground under nosignal (detuned) conditions.
no mark: FM
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production tolerances.
Note on Schematic Diagram: CD SECTION
• All capacitors are in mF unless otherwise noted. pF: mmF 50 WV
or less are not indicated except for electrolytics and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise specified.
Note: The components identified by mark ! or dotted line with
mark ! are critical for safety.
Replace only with part number specified.
• A : B+ Line.
• Voltages and waveforms are dc with respect to ground under nosignal conditions.
no mark: CD PLAY
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production tolerances.
• Circled numbers refer to waveforms.
• Signal path.
J: CD
j: MD REC
Note on Schematic Diagram: MD SECTION (1/2) (2/2)
• All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or
less are not indicated except for electrolytics and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise specified.
Note: The components identified by mark ! or dotted line with
mark ! are critical for safety.
Replace only with part number specified.
• A : B+ Line.
• Voltages and waveforms are dc with respect to ground under nosignal conditions.
no mark : STOP
(
) : PLAY
<
> : REC
: Impossible to measure
∗
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production tolerances.
• Circled numbers refer to waveforms.
• Signal path.
E : MD PLAY
j : MD REC
55
ZS-M30
• Waveforms – CD SECTION –
1 IC701qg(RFO)
(PLAY MODE)
VOLT/DIV : 0.5 V AC
TIME/DIV : 1 msec
5 IC702 yj (XTAO)
(PLAY MODE)
VOLT/DIV : 0.5 V AC
TIME/DIV : 20 µsec
2.1 Vp-p
1.1 – 1.3 Vp-p
33.8688 MHz
2 IC701 qd(FE)
(PLAY MODE)
VOLT/DIV : 0.1 V AC
TIME/DIV : 5 msec
• Waveforms – MAIN SECTION –
1IC801 ij TX
VOLT/DIV : 1 V AC
TIME/DIV : 20 µsec
0.6 Vp-p
3.4 Vp-p
32.768 kHz
3 IC701 qa (TE)
(PLAY MODE)
VOLT/DIV : 0.1 V AC
TIME/DIV : 5 msec
2IC801 rs XTAL
VOLT/DIV : 1 V AC
TIME/DIV : 0.1 µsec
0.3 Vp-p
2.8 Vp-p
8 MHz
4 IC702 rd (RF DC)
(PLAY MODE)
VOLT/DIV : 0.5 V AC
TIME/DIV : 1 msec
• Waveforms – TUNER SECTION –
1IC1 w; X OUT
VOLT/DIV : 0.5 V AC
TIME/DIV : 10 µsec
1.1 – 1.3 Vp-p
1.5 Vp-p
75 kHz
56
ZS-M30
• Waveforms – MD SECTION –
1 IC502 1,2I , J
(PLAY MODE)
VOLT/DIV : 0.2 V AC
TIME/DIV : 0.5 µsec
5 IC504 qj OSCO
VOLT/DIV : 0.5 V AC
TIME/DIV : 20 msec
9 IC504 o; FS4
VOLT/DIV : 1 V AC
TIME/DIV : 2 µsec
22 nsec
2 IC502 ek FE
(PLAY MODE)
VOLT/DIV : 0.5 V AC
TIME/DIV : 0.5 µsec
3.4 Vp-p
1.2 Vp-p
0.46 Vp-p
5.6 µsec
0 IC601 qd EXTAL
VOLT/DIV : 1 V AC
TIME/DIV : 0.1 µsec
6IC504 wj LRCK
VOLT/DIV : 1 V AC
TIME/DIV : 10 µsec
3.3 Vp-p
1.2–1.6 Vp-p
2.5 Vp-p
0.083 µsec
22.7 µsec
3 IC502 ef FE
(PLAY MODE)
VOLT/DIV : 100 V AC
TIME/DIV : 5 µsec
7IC504 wk XBCK
VOLT/DIV : 1 V AC
TIME/DIV : 0.1 µsec
3.5 Vp-p
0.2 Vp-p
0.36 µsec
4 IC502 wh TE
(PLAY Mode)
VOLT/DIV : 2 V AC
TIME/DIV : 5 msec
8IC504 wl FS256
VOLT/DIV : 1 V AC
TIME/DIV : 50 nsec
4 Vp-p
1.0 Vp-p
90 nsec
57
ZS-M30
• IC BLOCK DIAGRAMS (MAIN SECTION)
IC301,303 BA5417
IC305 NJM4558V-TE2
A OUT 1
8 VCC
7 B OUT
A
– +
T. S. D
A IN– 2
B
+ –
ST. BY
BS
2
3
4
5
6
7
8
9
10
11
12
13
14
15
OUT2
VCC
OUT1
B.S.1
POWER GND
ST-BY
FLTR
NF1
IN1
IN2
NF2
PRE GND
PRE GND
FILTER
B.S.2
N.C
1
BS
IC302 LC75342
30 CL
2
29 VDD
VSS
3
28 VREF
TEST
4
27 NC
LOUT
5
26 ROUT
LBASS2
6
LBASS1
7
LTRE
8
LIN
9
22 RIN
LSELO
10
21 RSELO
L4
11
20 R4
L3
12
19 R3
L2
13
18 R2
L1
14
17 R1
NC
15
16 NC
58
CCB
INTERFACE
RVREF
1
LVREF
DI
CE
25 RBASS2
CONTROL
CIRCUIT
LOGIC
CIRCUIT
CONTROL
CIRCUIT
24 RBASS1
23 RTRE
A IN+ 3
6 B IN–
VEE 4
5 B IN+
ZS-M30
• IC BLOCK DIAGRAMS (TUNER SECTION)
IC1 LV23000M-TLM
32
31
30
29
28
27
26
25
24
23
22
21
20
19
X IN
AM
RF
REG
3
BND1
4
AM
MIX
5
AM
IF
AM
DET
8
FM
IF
FM
DET
OSC
BUFFER
VCC1
7
FM
S-METER
6
IF
BUFFER
PILOT
DET
9
10
DECODER
12
14
SHALLOW
COUNTER
PHASE DETECTOR
CHARGE PUMP
PROGRAMMABLE
DIVIDER
16
I/F
DATA SHIFT REGISTER
LATCH
UNIVERSAL
COUNTER
15
17
REFERENCE
DEVIDER
UNLOCK
DETECTOR
18
D0
2
DI
1
CE
POWER ON
RESET
X OUT
CL
VCO
VDD
VSS
AM
OSC
MPX-IN
R-OUT
FM
OSC
DET-OUT
L-OUT
VCC2
AM LOW CUT
P-CONP
GND2
33
VCO
34
LPF
FF
AGC
FM-DET
ST SN
PD
FM IF-IN
TRIG
LP-IN
P-DET
SD
LP-OUT
AM IF-IN
FM
RF
35
ST
MUTE
BO1
VCC1
PHASE
COMP
BO2
FF
AM OSC
FF
36
AGC
FM OSC
AM MIX-OUT
FM
MIX
VCC2
GND1
VSS
FM RF-OUT
FM MIX-OUT
13
GND2
REG
11
FM RF-IN
AM RF-IN
59
ZS-M30
• IC BLOCK DIAGRAMS (CD SECTION)
IC701 CXA2550M-T6
AGCVTH 1
PD
VCC
1k
LD 2
APC PD
AMP VCC
20 VCC
APC LD
AMP
56k
19 LD ON
3
10k
VEE
10k
55k
56k
10k
VEE
VREF 1.25V
10k
18 AGCCONT
VCC
VC
13.4k
670mV
50µA
17 RFTC
16 RF I
VC
2k
15k
10k
PD1
VC
4
8k
VC
6k
6p
54k
VC
2k
VEE
VC
15 RF O
10k
PD2
2k
5
14 RFM
VC
8k
2k
6p
24p
32k
174k
32k
VEE
87k
13 FE
VEE
6
FOCUS
ERROR
154k AMP
24p
25k
VC
260k
F
E
7
13k
95k
VC
12p
30k
VC
12p
30k
8
260k
96k
VCC
26k
9
11 TE
13k
VC
EI
12 FE BIAS
VC
30k
TRACKING
VC ERROR
AMP
49
VC 10
30k
VC
15k
VEE
VREF
SPIN
NC
FFDR
FRDR
FCAP
GND
MUTE
VCC
F–
F+
SP–
SP+
28
27 26
25
24
23
22
21
20
19
18
17
16
15
10k
50k POWER
VCC
100k
PRE VCC
F
R
R
MUTE
+ –
190k
DRIVE BUFFER
VCC
IC703 BA5974FP-E2
30k
INTERFACE
F
LEVEL SHIFT
POWER
VCC
50k
30k
F
THERMAL
SHUTDOWN
VREF
INTERFACE
R
F
R
DRIVE BUFFER
F
INTERFACE
F
R
R
60
1
2
3
4
5
6
7
8
9
10
11
12
13
14
VREFOUT
TFDR
TRDR
TCAP
SFDR
SRDR
SCAP
GND
VREFIN
VCC
SL-
SL+
T+
T-
POWER
VCC
ZS-M30
DOUT
VDD
VSS
AVDD
PCO
FILI
FILO
CLTV
AVSS
RFAC
BIAS
ASYI
ASYO
AVDD
IGEN
AVSS
ADIO
RFDC
CE
TE
IC702 CXD3017Q
60
59 58 57
56
55
54
53
52
51
50
49
48
47
46 45 44
43
42
41
Digital
OUT
LRCK 61
PCMD 62
BCK 63
40 SE
D/A
Interface
Digital
PLL
A/D
Converter
Asymmetry
Corrector
OP Amp
Analog SW
39 FE
38 VC
37 XTSL
64
65
66
67
SERVO DSP
LOUT1 72
AVSS1 73
Over Sampling
Digital Filter
16K
RAM
3rd-Order
Noise Shaper
PWM
Servo Auto
Sequencer
PWM
AVSS2 74
75
76
77
78
RMUT 79
LMUT 80
PWM
GENERATOR
34 VSS
FOCUS
SERVO
FOCUS PWM
GENERATOR
TRACKING
SERVO
TRACKING
PWM
GENERATOR
SELED
SERVO
SLED PWM
GENERATOR
SERVO
Interface
Sub Code
Processor
LOUT2
AIN2
AOUT2
AVDD2
36 TES1
35 TEST
32 FFDR
31 TRDR
30 TFDR
29 SRDR
28 SFDR
27 SSTP
1
2
3 4
5
6
7
8
9 10 11 12 13 14 15 16 17 18
19
SQSO
SQCK
XRST
SYSM
DATA
XLAT
CLOK
SENS
SCLK
XPCK
GFS
C2PO
CPU
Interface
Digital
CLV
26 MDP
MIRR
DFCT
FOK
24 FOK
23 DFCT
22 MIRR
21 COUT
25 LOCK
20
SCOR
AIN1 71
EFM
Demodurator
WFCK
XUGF
AOUT1 70
Timing
Logic
Clock
Generator
33 FRDR
Error
Corrector
Serial-In
Interface
VDD
XVSS 68
AVDD1 69
ATSK
SPOA
SPOB
XLON
EMPH
XVDD
XTAI
XTAO
61
ZS-M30
• IC BLOCK DIAGRAMS (MD SECTION)
CAPA–
CAPA+
IN2R
IN2F
VM2
OUT2F
PGND2
OUT2R
VM12
OUT1R
PGND1
OUT1F
VM1
IN1F
IN1R
VDD
IC501 BH6511FS-E2
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
AMP
AMP
PRE DRIVE
PRE DRIVE
PRE DRIVE
PRE DRIVE
3
4
5
6
7
8
9
10
11
12
IN4R
IN4F
VM4
OUT4F
PGND4
OUT4R
VM34
OUT3R
PGND3
OUT3F
PSB
13
14
15
16
PSB
2
INTERFACE
IN3R
1
VG
AMP
GND
AMP
IN3F
AMP
AMP
INTERFACE
VDD
INTERFACE
VM3
CHARGE
PUMP.
OSC
AMP
AMP
INTERFACE
IC602 BA6287F-T1
IC603 BR24C02F-WE2
8 VCC
OUT1 1
8 GND
1KBIT EEPROM ARRAY
8BIT
7BIT
ADDRESS
DECODER
7BIT
SAVE•WORD
ADDRESS
REGISTER
VM 2
DATA
REGISTER
7 OUT2
DRIVER
DRIVER
TSD
START
STOP
A0 1
A1 2
7 WP
5 SDA
62
HI-VOLTAGE
OCUURENCE CIRCUIT
CONTROL LOGIC
6 VREF
6 SCL
CONTROL LOGIC
A2 3
GND 4
VCC 3
POWER SUPPLY
VOLTAGE DET
POWER
SAVE
FIN 4
5 RIN
ZS-M30
VCC2
AGND1
AGND2
VCOM
VOUTR
VOUTL
DEM0
DEM1
20BIT
DIN
VDD
DGND
IC604 PCM3003E/T2
24
23
22
21
20
19
18
17
16
15
14
13
MODE CONTROL
INTERFACE
ANALOG
LOW-PASS
FILTER
MULTI-LEVEL
DELTA-SIGMA
MODULATOR
INTERPOLATION
FILTER
OVERFLOWING
D/A
CONVERTER
ANALOG
LOW-PASS
FILTER
MULTI-LEVEL
DELTA-SIGMA
MODULATOR
INTERPOLATION
FILTER
OVERFLOWING
SERIAL
INTERFACE
POWER
SUPPLY
DECIMATION
&
LOW CUT FILTER
A/D
CONVERTER
DELTA-SIGMA
MODULATOR
(+) (-)
DECIMATION
&
LOW CUT FILTER
DELTA-SIGMA
MODULATOR
(+) (-)
1
2
3
4
5
6
7
8
9
10
11
12
VERF2
VINL
PDAD
PDDA
SYSCK
LRCK
BCK
DOUT
CLOCK
VERF1
RESET AND
POWER DOWN
VINR
ANALOG
FRONT-END
CIRCUIT
VCC1
REFERENCE
VCC1
ANALOG
FRONT-END
CIRCUIT
63
ZS-M30
SECTION 7
EXPLODED VIEWS
NOTE :
• -XX, -X mean standardized parts, so they
may have some difference from the original
one.
• Color indication of Appearance Parts
Example :
KNOB, BALANCE (WHITE) ••• (RED)
↑
↑
Parts color Cabinet's color
• Items marked “ * ”are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering
these items.
• The mechanical parts with no reference
number in the exploded views are not
supplied.
• Hardware (# mark) list and accessories and
packing materials are given in the last of this
parts list.
The components identified by mark 0
or dotted line with mark 0 are critical
for safety.
Replace only with part number specified.
7-1. REAR CABINET SECTION
12
8
10
ANT1
#11
9
#9
11
#9
#6
#10
#9
#10
T901
#11
6
F901
#10
F902
5
4
7
#9
6
#10
#10
12
2
#12
3
1
#10
#10
#10
Ref. No.
Part No.
Description
* 1
2
3
* 4
* 5
A-3347-168-A
3-222-353-01
3-222-362-01
1-679-404-21
1-679-405-21
TUNER BOARD, COMPLETE
CHASSIS (TU)
TERMINAL, ANT
BATT (A) BOARD
BATT (B) BOARD
6
* 7
8
9
9
3-039-967-01
1-679-406-21
3-222-350-01
3-222-341-41
3-222-341-51
TERMINAL (–) , BATTERY
POWER BOARD
CHASSIS, TRANSFORMER
CABINET (REAR) ... (ORANGE)
CABINET (REAR) ... (WHITE)
9
9
10
64
3-222-341-61 CABINET (REAR) ... (BLUE)
3-222-341-71 CABINET (REAR) ... (GREEN)
3-222-343-01 HANDLE... (ORANGE)
Remark
Ref. No.
Part No.
#10
Description
10
10
3-222-343-11 HANDLE... (WHITE)
3-222-343-21 HANDLE... (BLUE)
10
11
11
11
11
12
3-222-343-31
3-226-496-01
3-226-496-11
3-226-496-21
3-226-496-31
3-831-441-99
HANDLE... (GREEN)
LID, BATTERY CASE... (ORANGE)
LID, BATTERY CASE... (WHITE)
LID, BATTERY CASE... (BLUE)
LID, BATTERY CASE... (GREEN)
CUSHION (A)
ANT1
! F901
! F902
! T901
1-501-452-11
1-532-465-51
1-532-503-51
1-435-872-11
ANTENNA, TELESCOPIC
FUSE,TIME LAG 3.15A/250V
FUSE,TIME LAG 1.6A/250V
TRANSFORMER, POWER
Remark
ZS-M30
7-2. FRONT CABINET SECTION
64
63
#10
62
#10
61
SP102
#10
not
supplied
65
SP101
#10
#10
68
60
72
61
#10
#10
#10
66
69 72
59
#10
72
58
#10
SP201
#10
70
62
68
71
67
SP202
56
54
53
57
55
52
51
Ref. No.
Part No.
Description
51
51
51
51
52
X-3379-522-1
X-3379-574-1
X-3379-575-1
X-3379-576-1
3-222-387-01
CHASSIS ASSY, NET (ORANGE)
CHASSIS ASSY, NET (WHITE)
CHASSIS ASSY, NET (BLUE)
CHASSIS ASSY, NET (GREEN)
ORNAMENT (CD.MD) , BUTTON...
(ORANGE,WHITE,BLUE)
52
53
3-222-387-11 ORNAMENT (CD.MD) , BUTTON... (GREEN)
3-222-388-01 ORNAMENT (BAND.LINE) , BUTTON...
(ORANGE,WHITE,BLUE)
3-222-388-11 ORNAMENT (BAND.LINE) , BUTTON...(GREEN)
3-222-349-01 KNOB (JOG)
3-222-386-01 PLATE (JOG) , ORNAMENTAL...
(ORANGE,WHITE)
53
54
55
Remark
55
55
56
56
56
3-222-386-11
3-222-386-21
3-222-352-01
3-222-352-11
3-222-352-21
PLATE (JOG) , ORNAMENTAL... (BLUE)
PLATE (JOG) , ORNAMENTAL... (GREEN)
WINDOW (LCD) ... (ORANGE)
WINDOW (LCD) ... (WHITE)
WINDOW (LCD) ... (BLUE)
56
57
57
57
57
3-222-352-31
3-222-336-01
3-222-336-11
3-222-336-21
3-222-336-31
WINDOW (LCD) ... (GREEN)
CABINET (FRONT) ... (ORANGE)
CABINET (FRONT) ... (WHITE)
CABINET (FRONT) ... (BLUE)
CABINET (FRONT) ... (GREEN)
Ref. No.
Part No.
Description
58
58
58
58
59
3-222-344-01
3-222-344-11
3-222-344-21
3-222-344-31
3-224-892-01
BUTTON (PLAY) ... (ORANGE)
BUTTON (PLAY) ... (WHITE)
BUTTON (PLAY) ... (BLUE)
BUTTON (PLAY) ... (GREEN)
CUSHION
* 60
61
* 62
63
* 64
1-679-403-21
4-951-620-11
3-222-389-01
1-757-153-11
1-679-402-21
SW (L) BOARD
SCREW (2.6X10) , +BVTP
BRACKET (SP)
WIRE, PARALLEL (FFC) (8 CORE)
SW (R) BOARD
* 65
66
67
68
69
1-679-407-21
3-222-346-01
3-222-337-01
3-831-441-99
3-226-251-01
JACK BOARD
BUTTON (EJECT)
WINDOW, REMOTE CONTROL
CUSHION (A)
SHEET (LCD) , ADHESIVE
70
71
72
SP101
SP102
3-041-801-01
3-040-916-01
3-831-441-11
1-529-846-11
1-529-847-11
SHEET (B) , ADHESIVE
FOOT (F) , RUBBER
CUSHION (F)
SPEAKER (8 cm) (L-CH)
SPEAKER (5.7 cm) (L-CH)
SP201
SP202
1-529-846-11 SPEAKER (8 cm) (R-CH)
1-529-847-11 SPEAKER (5.7 cm) (R-CH)
Remark
65
ZS-M30
7-3. UPPER CABINET SECTION
111
110
S701
109
112
108
124
114
#10
113
107
121
#8
106
115
105
117
116
115
103
102
#10
104
117
117
not
supplied
116
117
123
118
LCD1
101
#10
#10
#10
122
Ref. No.
Part No.
Description
* 101
102
103
104
* 105
A-3347-176-A
3-222-467-01
3-222-351-01
4-951-620-11
1-679-401-21
MAIN BOARD, COMPLETE
ILLUMINATOR
HOLDER (LCD)
SCREW (2.6X10) , +BVTP
TOP BOARD
106
107
108
109
109
1-757-152-11
3-222-348-11
3-049-782-21
3-222-342-01
3-222-342-11
WIRE, PARALLEL (FFC) (6 CORE)
BUTTON (TOP)
DAMPER
CABINET (UPPER) ... (ORANGE)
CABINET (UPPER) ... (WHITE)
109
109
110
111
111
3-222-342-21
3-222-342-31
3-222-361-01
3-222-340-01
3-222-340-11
CABINET (UPPER) ... (BLUE)
CABINET (UPPER) ... (GREEN)
SPRING (CD UP)
LID, CD... (ORANGE)
LID, CD... (WHITE)
111
111
3-222-340-21 LID, CD... (BLUE)
3-222-340-31 LID, CD... (GREEN)
66
120
#10
Remark
Ref. No.
112
113
114
Part No.
#1
119
Description
115
116
117
* 118
119
3-931-379-31
3-931-379-21
3-921-725-11
A-3347-177-A
1-757-470-11
RUBBER, VIBRATION PROOF (PINK)
RUBBER, VIBRATION PROOF (GREEN)
SCREW (2.6X10) , +PWH
CD BOARD, COMPLETE
WIRE, PARALLEL (FFC) (16 CORE)
120
121
* 122
123
124
1-757-154-11
3-225-870-01
1-679-400-21
3-226-009-01
3-831-441-11
CABLE, FLEXIBLE FLAT (19 CORE)
CUSHION, RUBBER
LCD BOARD
SHEET (CD), ADHESIVE
CUSHION (B)
LCD1
S701
Remark
1-471-110-11 MAGNET
3-021-020-01 PLATE, CHUCKING
3-923-736-01 COVER, CD
1-476-281-11 INDICATOR UNIT, LIQUID CRYSTAL
1-692-960-11 SWITCH, PUSH (1 KEY) (CD DOOR OPEN/
CLOSE)
ZS-M30
7-4. OPTICAL PICK-UP SECTION (KSM-213CDP)
154
not supplied
not supplied
151
M901
152
155
M902
153
(including M901)
The components identified by mark 0
or dotted line with mark 0 are critical
for safety.
Replace only with part number specified.
Ref. No.
151
152
153
Part No.
Remark
Ref. No.
Part No.
3-713-786-51 SCREW +P 2X3
2-626-908-01 SHAFT, SLED
X-2646-381-1 SHASSIS ASSY, MOTOR (MB) (SPINDLE)
(INCLUDING M901)
Description
! 154
155
M902
8-848-483-05 OPTICAL PICK-UP KSS-213C
2-627-003-01 GEAR B (RP)
X-2625-769-1 GEAR ASSY, MOTOR (MB) (SLED)
(INCLUDING GEAR)
Description
Remark
67
ZS-M30
7-5. MD SECTION-1 (MT-ZSM30-168)
#12
225
#12
#12
216
not supplied
219
218
215
213
#5
M103
217
220
212
213
210
214
221
211
222
208
212
207
213
209
224
223
206
205
204
202
not supplied
201
203
#7
Ref. No.
Part No.
Description
* 201
202
203
204
* 205
A-3322-905-A
1-669-180-11
1-757-156-11
1-792-047-11
3-042-574-01
MD BOARD, COMPLETE
OP FLEXIBLE BOARD
CABLE, FLEXIBLE FLAT (9 CORE)
CABLE, FLEXIBLE FLAT (7 CORE)
SLIDER
* 206
207
* 208
209
210
3-042-575-01
3-042-582-01
3-042-572-01
3-042-587-12
3-042-585-13
CATCHER, LOADING
SPRING, CATCHER
CHASSIS
LID (B)
LID (A)
211
212
213
* 214
3-042-586-01
3-044-636-01
3-042-689-01
1-679-414-11
SPRING, LID (A)
SCREW, MD FITTING
DAMPER
DETECTION BOARD
68
Remark
Ref. No.
215
Part No.
Description
Remark
3-042-588-01 SCREW (1.4X4) , PWH
* 216
217
218
219
* 220
3-042-573-01
3-042-579-01
3-042-580-01
3-042-576-01
A-3322-907-A
LIFTER
GEAR (A)
GEAR (B)
GEAR, LOADING
REC BOARD, COMPLETE
221
222
223
224
225
3-042-583-01
3-042-577-01
3-042-581-01
1-757-155-11
3-831-441-99
SPRING, HEAD ARM
ARM, HEAD
SPRING, SHUTTER
WIRE, PARALLEL (FFC) (22 CORE)
CUSFION (A)
M103
X-3378-325-1 MOTOR ASSY, LOADING (INCLUDING GEAR)
ZS-M30
7-6. MD SECTION-2 (MT-ZSM30-168)
259
265
262
M602
263
258
260
not supplied
261
257
256
#2
264
256
#3
267
HR901
255
254
#2
266
252
#2
256
253
251
M601
#2
#4
The components identified by mark 0
or dotted line with mark 0 are critical
for safety.
Replace only with part number specified.
Ref. No.
Part No.
Description
Remark
! 251
252
253
* 254
A-4672-541-A
2-646-452-01
3-042-584-01
2-646-566-01
KMS-260B (MD) OPTICAL PICK-UP ASSY
SHAFT, GUIDE
LEVER, DETECTION
BRACKET, SP MOTOR
255
256
* 257
258
* 259
2-648-052-01
2-627-404-01
1-677-526-11
2-627-431-01
2-646-571-11
GUIDE, SUB
GRIP (1.4X3.5)
D SW BOARD
SCREW (1.2X3.3)
GEAR (MD)
* 260
261
2-646-567-01 PLATE, PRE ROAD
2-648-049-01 BRACKET, SL MOTOR
Ref. No.
Part No.
262
* 263
* 264
X-2626-330-1 SCREW ASSY, LEAD
2-646-574-03 HOLDER (A) , LEAD
2-646-573-01 HOLDER (B) , LEAD
265
* 266
267
* HR901
M601
2-648-055-01
2-647-338-01
1-676-550-11
1-500-518-11
X-2626-327-1
M602
Description
Remark
GEAR (LD)
SPRING, RACK
FLEXIBLE BOARD
HEAD, MD OVER LIGHT
MOTOR ASSY, SPINDLE (MB) (SPINDLE)
X-2646-617-2 MOTOR ASSY, SLED (SLED) (INCLUDING
GEAR)
69
ZS-M30
BATT (A)
BATT (B)
CD
NOTE :
• Due to standardization, replacements in the
parts list may be different from the parts
specified in the diagrams or the components
used on the set.
• -XX, -X mean standardized parts, so they
may have some difference from the original
one.
• RESISTORS
All resistors are in ohms
METAL : Metal-film resistor
METAL OXIDE :Metal oxide-film resistor
F : nonflammable
• Items marked “ * ”are not stocked since
they are seldom required for routine service.
Some delay should be anticipated when
ordering these items.
Ref. No.
Part No.
*
1-679-404-21 BATT (A) BOARD
**************
SECTION 8
ELECTRICAL PARTS LIST
Description
Remark
3-039-967-01 TERMINAL (–) , BATTERY
**************************************************************
1-679-405-21 BATT (B) BOARD
**************
*
3-039-967-01 TERMINAL (–) , BATTERY
**************************************************************
A-3347-177-A CD BOARD, COMPLETE
*******************
*
< CAPACITOR >
C701
C702
C703
C704
C705
1-164-230-11
1-162-970-11
1-162-919-11
1-104-664-11
1-162-919-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
220PF
0.01uF
22PF
47uF
22PF
5%
10%
5%
20%
5%
50V
25V
50V
10V
50V
C706
C707
C708
C710
C711
1-162-964-11
1-104-665-11
1-104-665-11
1-162-970-11
1-107-823-11
CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
0.001uF
100uF
100uF
0.01uF
0.47uF
10%
20%
20%
10%
10%
50V
10V
10V
25V
16V
C712
C713
C714
C715
C716
1-162-968-11
1-164-227-11
1-107-826-11
1-164-230-11
1-164-230-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0047uF
0.022uF
0.1uF
220PF
220PF
10%
10%
10%
5%
5%
50V
25V
16V
50V
50V
C717
C720
C721
C722
C723
1-104-664-11
1-162-970-11
1-162-970-11
1-107-823-11
1-164-230-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
47uF
0.01uF
0.01uF
0.47uF
220PF
20%
10%
10%
10%
5%
10V
25V
25V
16V
50V
C726
C727
C729
C730
C731
1-162-962-11
1-107-823-11
1-104-665-11
1-162-970-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
470PF
0.47uF
100uF
0.01uF
0.01uF
10%
10%
20%
10%
10%
50V
16V
10V
25V
25V
C732
C733
C734
C737
1-162-970-11
1-162-915-11
1-162-919-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
10PF
22PF
0.01uF
10%
0.5PF
5%
10%
25V
50V
50V
25V
70
The components identified by mark 0
or dotted line with mark 0 are critical
for safety.
Replace only with part number specified.
• SEMICONDUCTORS
In each case, u : µ , for example :
uA.... : µ A.... , uPA.... : µ PA....
uPB.... : µ PB.... , uPC.... : µ PC....
uPD.... : µ PD....
• CAPACITORS
uF : µ F
• COILS
uH : µ H
Ref. No.
When indicating parts by reference number, please include the board.
Part No.
Description
Remark
C738
1-162-970-11 CERAMIC CHIP
0.01uF
10%
25V
C739
C740
C741
C743
C744
1-162-962-11
1-162-923-11
1-162-964-11
1-162-923-11
1-162-962-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
470PF
47PF
0.001uF
47PF
470PF
10%
5%
10%
5%
10%
50V
50V
50V
50V
50V
C746
C757
C758
C759
C760
1-126-934-11
1-162-927-11
1-162-962-11
1-162-970-11
1-162-927-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
220uF
100PF
470PF
0.01uF
100PF
20%
5%
10%
10%
5%
10V
50V
50V
25V
50V
C761
C762
C764
C765
C766
1-104-665-11
1-107-823-11
1-162-927-11
1-164-230-11
1-162-927-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100uF
0.47uF
100PF
220PF
100PF
20%
10%
5%
5%
5%
10V
16V
50V
50V
50V
C768
C781
1-162-970-11 CERAMIC CHIP
1-104-665-11 ELECT
0.01uF
100uF
10%
20%
25V
10V
< CONNECTOR >
CN701
CN702
CN703
1-779-466-11 CONNECTOR,FFC (LIF (NON-ZIF) ) 16P
1-695-380-31 PIN, CONNECTOR (PC BOARD) 19P
1-569-614-11 PLUG, CONNECTOR 2P
< FERRITE BEAD >
FB703
FB704
FB705
FB706
1-216-864-91
1-216-864-91
1-216-864-91
1-216-864-91
SHORT
SHORT
SHORT
SHORT
0
0
0
0
< IC >
IC701
IC702
IC703
8-752-097-74 IC CXA2550M-T6
8-752-402-31 IC CXD3017Q
8-759-549-28 IC BA5974FP-E2
< JUMPER >
JC701
JC703
JC707
JC708
JC711
1-216-864-91
1-216-864-91
1-216-864-91
1-216-864-91
1-216-864-91
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
JC712
1-216-864-91 SHORT
0
ZS-M30
CD
Ref. No.
JC720
JC721
JC722
Part No.
Description
1-216-864-91 SHORT
1-216-864-91 SHORT
1-216-864-91 SHORT
Remark
0
0
0
< COIL >
L701
L702
1-412-981-11 INDUCTOR
1-216-813-11 METAL CHIP
1.5uH
220
5%
1/16W
Ref. No.
D SW
Part No.
DETECTION
Description
JACK
Remark
R777
R779
R780
1-216-821-11 METAL CHIP
1-216-821-11 METAL CHIP
1-216-821-11 METAL CHIP
1K
1K
1K
5%
5%
5%
1/16W
1/16W
1/16W
R781
R782
R783
R785
R786
1-216-821-11
1-216-821-11
1-216-841-11
1-216-837-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
47K
22K
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R787
R788
R790
R791
R799
1-216-821-11
1-216-821-11
1-216-821-11
1-216-843-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
1K
68K
47K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
< TRANSISTOR >
Q701
Q702
Q703
Q705
Q707
8-729-903-46
8-729-900-53
8-729-931-02
8-729-027-60
8-729-027-60
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SB1132-P
DTC114EK
2SC2413KQ
DTC144TKA-T146
DTC144TKA-T146
< SWITCH >
< RESISTOR >
S702
R701
R702
R703
R704
R705
1-216-849-11
1-216-849-11
1-216-827-11
1-216-827-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
220K
220K
3.3K
3.3K
47K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R706
R707
R708
R709
R710
1-216-829-11
1-216-829-11
1-216-797-11
1-216-835-11
1-412-967-31
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
INDUCTOR
4.7K
4.7K
10
15K
0.1uH
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
R712
R713
R714
R715
R716
1-216-833-11
1-216-839-11
1-216-845-11
1-216-839-11
1-216-839-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
33K
100K
33K
33K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R717
R718
R719
R720
R721
1-216-833-11
1-216-845-11
1-216-857-11
1-216-833-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
100K
1M
10K
1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R722
R723
R724
R725
R726
1-216-827-11
1-216-839-11
1-216-839-11
1-216-839-11
1-216-839-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
3.3K
33K
33K
33K
33K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R727
R728
R729
R730
R731
1-216-839-11
1-216-839-11
1-216-819-11
1-216-821-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
33K
33K
680
1K
47K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R732
R735
R736
R750
R751
1-216-864-91
1-216-809-11
1-216-809-11
1-216-837-11
1-216-843-11
SHORT
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
100
100
22K
68K
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
R759
R760
R761
R762
R774
1-216-845-11
1-216-845-11
1-216-845-11
1-216-845-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
100K
100K
100K
1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R775
R776
1-216-821-11 METAL CHIP
1-216-821-11 METAL CHIP
1K
1K
5%
5%
1/16W
1/16W
1-762-812-11 SWITCH, LEAF (LIMIT)
< VIBRATOR >
X701
1-795-046-21 VIBRATOR, CRYSTAL (33.8688MHz)
**************************************************************
1-677-526-11 D SW BOARD
***********
< CONNECTOR >
* CN108
1-794-627-21 CONNECTOR, FFC/FPC 7P
< SWITCH >
SW5
1-771-327-11 SWITCH, 2PIN PUSH (2KEY)(PROTECT/
REFLECT)
**************************************************************
1-679-414-11 DETECTION BOARD
****************
< SWITCH >
S503
1-572-688-11 SWITCH, PUSH LEVER (1KEY) (PACK OUT)
**************************************************************
1-679-407-21 JACK BOARD
***********
< HOLDER >
* CH302
* CH306
1-565-386-11 HOLDER, CABLE 5P
1-815-170-11 HOLDER, CABLE 4P
< CONNECTOR >
* CN304
1-564-778-11 PLUG, CONNECTOR (2.5MM) 4P
< DIODE >
D306
D307
D308
D309
8-719-988-61
8-719-988-61
8-719-988-61
8-719-988-61
DIODE
DIODE
DIODE
DIODE
1SS355TE-17
1SS355TE-17
1SS355TE-17
1SS355TE-17
< FERRITE BEAD >
FB102
FB202
1-216-864-91 SHORT
1-216-864-91 SHORT
0
0
71
ZS-M30
JACK
Ref. No.
LCD
Part No.
MAIN
Description
Remark
< COIL >
L101
L201
L301
L302
1-412-987-41
1-412-987-41
1-412-987-41
1-412-987-41
INDUCTION
INDUCTION
INDUCTION
INDUCTION
4.7uH
4.7uH
4.7uH
4.7uH
< JACK >
J301
J302
1-794-838-11 JACK (2)
1-566-891-11 JACK (LINE IN)
< RESISTOR >
R127
1-216-813-11 METAL CHIP
220
5%
1/16W
R227
1-216-813-11 METAL CHIP
220
5%
1/16W
**************************************************************
1-679-400-21 LCD BOARD
**********
3-222-351-01 HOLDER (LCD)
3-222-467-01 ILLUMINATOR
7-685-647-79 SCREW +BVTP
3X10 TYPE2 N-S
< CAPACITOR >
C407
1-107-826-11 CERAMIC CHIP
0.1uF
10%
Part No.
Description
Remark
C103
C104
C105
1-126-963-11 ELECT
1-162-927-11 CERAMIC CHIP
1-104-664-11 ELECT
4.7uF
100PF
47uF
20%
5%
20%
50V
50V
10V
C106
C107
C108
C110
C111
1-130-495-00
1-130-495-00
1-126-960-11
1-126-961-11
1-126-961-11
MYLAR
MYLAR
ELECT
ELECT
ELECT
0.1uF
0.1uF
1uF
2.2uF
2.2uF
5%
5%
20%
20%
20%
50V
50V
50V
50V
50V
C112
C113
C114
C115
C116
1-126-961-11
1-126-961-11
1-126-961-11
1-130-495-00
1-137-366-11
ELECT
ELECT
ELECT
MYLAR
MYLAR
2.2uF
2.2uF
2.2uF
0.1uF
0.0022uF
20%
20%
20%
5%
5%
50V
50V
50V
50V
50V
C117
C118
C119
C120
C121
1-130-495-00
1-126-961-11
1-130-495-00
1-104-664-11
1-126-963-11
MYLAR
ELECT
MYLAR
ELECT
ELECT
0.1uF
2.2uF
0.1uF
47uF
4.7uF
5%
20%
5%
20%
20%
50V
50V
50V
10V
50V
C122
C123
C124
C125
C126
1-130-495-00
1-104-664-11
1-162-927-11
1-104-664-11
1-126-960-11
MYLAR
ELECT
CERAMIC CHIP
ELECT
ELECT
0.1uF
47uF
100PF
47uF
1uF
5%
20%
5%
20%
20%
50V
10V
50V
10V
50V
C129
C130
C201
C202
C203
1-126-963-11
1-137-366-11
1-126-926-11
1-126-960-11
1-126-963-11
ELECT
MYLAR
ELECT
ELECT
ELECT
4.7uF
0.0022uF
1000uF
1uF
4.7uF
20%
5%
20%
20%
20%
50V
50V
10V
50V
50V
C204
C205
C206
C207
C208
1-162-927-11
1-104-664-11
1-130-495-00
1-130-495-00
1-126-960-11
CERAMIC CHIP
ELECT
MYLAR
MYLAR
ELECT
100PF
47uF
0.1uF
0.1uF
1uF
5%
20%
5%
5%
20%
50V
10V
50V
50V
50V
C210
C211
C212
C213
C214
1-126-961-11
1-126-961-11
1-126-961-11
1-126-961-11
1-126-961-11
ELECT
ELECT
ELECT
ELECT
ELECT
2.2uF
2.2uF
2.2uF
2.2uF
2.2uF
20%
20%
20%
20%
20%
50V
50V
50V
50V
50V
C215
C216
C217
C218
C219
1-130-495-00
1-137-366-11
1-130-495-00
1-126-961-11
1-130-495-00
MYLAR
MYLAR
MYLAR
ELECT
MYLAR
0.1uF
0.0022uF
0.1uF
2.2uF
0.1uF
5%
5%
5%
20%
5%
50V
50V
50V
50V
50V
C220
C221
C222
C223
C224
1-104-664-11
1-126-963-11
1-130-495-00
1-104-664-11
1-162-927-11
ELECT
ELECT
MYLAR
ELECT
CERAMIC CHIP
47uF
4.7uF
0.1uF
47uF
100PF
20%
20%
5%
20%
5%
10V
50V
50V
10V
50V
C225
C226
C229
C230
C303
1-104-664-11
1-126-960-11
1-126-963-11
1-137-366-11
1-128-548-11
ELECT
ELECT
ELECT
MYLAR
ELECT
47uF
1uF
4.7uF
0.0022uF
4700uF
20%
20%
20%
5%
20%
10V
50V
50V
50V
25V
C304
C306
C308
C309
C310
1-104-664-11
1-126-964-11
1-104-665-11
1-104-664-11
1-104-664-11
ELECT
ELECT
ELECT
ELECT
ELECT
47uF
10uF
100uF
47uF
47uF
20%
20%
20%
20%
20%
10V
50V
10V
10V
10V
16V
< CONNECTOR >
CN404
Ref. No.
1-573-069-11 SOCKET, CONNECTOR 7P
< LIQUID CRYSTAL DISPLAY >
LCD1
1-476-281-11 INDICATOR UNIT, LIQUID CRYSTAL
< PILOT LAMP >
PL404
PL404
PL404
PL405
PL405
1-517-409-11
1-518-726-11
1-518-727-11
1-517-409-11
1-518-726-11
LAMP, PILOT (ORANGE) (BACK LIGHT)
LAMP, PILOT (WHITE,BLUE) (BACK LIGHT)
LAMP, PILOT (GREEN) (BACK LIGHT)
LAMP, PILOT (ORANGE) (BACK LIGHT)
LAMP, PILOT (WHITE,BLUE) (BACK LIGHT)
PL405
1-518-727-11 LAMP, PILOT (GREEN) (BACK LIGHT)
< RESISTOR >
R424
R425
R426
R427
R428
1-216-821-11
1-216-821-11
1-216-821-11
1-216-841-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
1K
47K
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R429
1-216-839-11 METAL CHIP
33K
5%
1/16W
R430
1-216-864-91 SHORT
0
**************************************************************
A-3347-176-A MAIN BOARD, COMPLETE
*********************
7-685-647-79 SCREW +BVTP
7-685-647-79 SCREW +BVTP
3X10 TYPE2 N-S
3X10 TYPE2 N-S
< CAPACITOR >
C101
C102
72
1-126-926-11 ELECT
1-126-960-11 ELECT
1000uF
1uF
20%
20%
10V
50V
ZS-M30
MAIN
Ref. No.
Part No.
Description
C311
C319
C323
C326
C801
1-104-664-11
1-126-960-11
1-104-665-11
1-126-964-11
1-162-920-11
ELECT
ELECT
ELECT
ELECT
CERAMIC CHIP
47uF
1uF
100uF
10uF
27PF
20%
20%
20%
20%
5%
10V
50V
10V
50V
50V
Remark
C803
C804
C805
C806
C807
1-162-921-11
1-162-921-11
1-162-964-11
1-162-964-11
1-162-919-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
33PF
33PF
0.001uF
0.001uF
22PF
5%
5%
10%
10%
5%
50V
50V
50V
50V
50V
C808
C810
C811
C813
C814
1-162-915-11
1-126-937-11
1-104-665-11
1-104-664-11
1-104-665-11
CERAMIC CHIP
ELECT
ELECT
ELECT
ELECT
10PF
4700uF
100uF
47uF
100uF
0.5PF
20%
20%
20%
20%
50V
16V
10V
10V
10V
C816
C817
C818
C819
C820
1-104-664-11
1-104-664-11
1-104-665-11
1-162-970-11
1-104-664-11
ELECT
ELECT
ELECT
CERAMIC CHIP
ELECT
47uF
47uF
100uF
0.01uF
47uF
20%
20%
20%
10%
20%
10V
10V
10V
25V
10V
C821
C822
C823
C825
C827
1-104-664-11
1-162-970-11
1-126-964-11
1-104-664-11
1-104-664-11
ELECT
CERAMIC CHIP
ELECT
ELECT
ELECT
47uF
0.01uF
10uF
47uF
47uF
20%
10%
20%
20%
20%
10V
25V
50V
10V
10V
C828
C829
C831
C832
C833
1-104-664-11
1-104-664-11
1-162-964-11
1-162-964-11
1-162-964-11
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
47uF
47uF
0.001uF
0.001uF
0.001uF
20%
20%
10%
10%
10%
10V
10V
50V
50V
50V
C834
C835
C836
C838
C839
1-162-964-11
1-162-964-11
1-162-964-11
1-162-964-11
1-162-964-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.001uF
0.001uF
0.001uF
0.001uF
10%
10%
10%
10%
10%
50V
50V
50V
50V
50V
C840
C842
C843
C844
C845
1-162-964-11
1-162-964-11
1-162-964-11
1-162-964-11
1-162-964-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.001uF
0.001uF
0.001uF
0.001uF
10%
10%
10%
10%
10%
50V
50V
50V
50V
50V
C846
C847
C848
C849
C850
1-162-964-11
1-162-964-11
1-162-964-11
1-162-964-11
1-162-962-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.001uF
0.001uF
0.001uF
470PF
10%
10%
10%
10%
10%
50V
50V
50V
50V
50V
C853
C854
C855
C856
C857
1-162-964-11
1-162-964-11
1-162-964-11
1-162-964-11
1-162-964-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.001uF
0.001uF
0.001uF
0.001uF
10%
10%
10%
10%
10%
50V
50V
50V
50V
50V
C859
C861
C862
C863
C864
1-162-964-11
1-162-964-11
1-162-964-11
1-162-964-11
1-104-905-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CAPACITOR
0.001uF
0.001uF
0.001uF
0.001uF
0.22F
10%
10%
10%
10%
50V
50V
50V
50V
5.5V
C865
C869
C870
1-162-964-11 CERAMIC CHIP
1-162-964-11 CERAMIC CHIP
1-126-960-11 ELECT
0.001uF
0.001uF
1uF
10%
10%
20%
50V
50V
50V
Ref. No.
Part No.
Description
Remark
C877
C878
1-164-378-11 CERAMIC CHIP
1-162-915-11 CERAMIC CHIP
30PF
10PF
5%
0.5PF
50V
50V
C879
C881
C882
C883
1-104-664-11
1-162-964-11
1-162-964-11
1-285-511-11
47uF
0.001uF
0.001uF
22uF
20%
10%
10%
20%
10V
50V
50V
25V
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
< HOLDER >
* CH802
1-815-154-11 HOLDER, CABLE 10P
< CONNECTOR >
CN301
CN302
CN303
CN801
CN803
1-785-656-21
1-785-656-11
1-785-657-11
1-564-779-11
1-695-329-31
PIN, CONNECTOR (PC BOARD) 4P
PIN, CONNECTOR (PC BOARD) 4P
PIN, CONNECTOR (PC BOARD) 5P
PLUG, CONNECTOR (2.5MM) 6P
PIN, CONNECTOR (PC BOARD) 6P
* CN804
* CN805
CN807
CN808
CN810
1-568-827-11
1-785-654-11
1-770-650-11
1-695-342-31
1-569-614-11
PIN, CONNECTOR (PC BOARD) 8P
PIN, CONNECTOR (PC BOARD) 2P
CONNECTOR, FFC/FPC 22P
PIN, CONNECTOR (PC BOARD) 19P
PLUG, CONNECTOR 2P
*
*
*
*
*
< DIODE >
D101
D201
D301
D802
D803
8-719-988-61
8-719-988-61
8-719-988-61
8-719-988-61
8-719-056-85
DIODE
DIODE
DIODE
DIODE
DIODE
1SS355TE-17
1SS355TE-17
1SS355TE-17
1SS355TE-17
UDZ-TE-17-8.2B
D804
D805
D806
D811
8-719-422-12
8-719-056-84
8-719-988-61
8-719-056-84
DIODE
DIODE
DIODE
DIODE
MA8039
UDZ-TE-17-7.5B
1SS355TE-17
UDZ-TE-17-7.5B
< FERRITE BEAD >
FB802
FB803
FB806
FB807
FB808
1-500-329-21
1-500-329-21
1-500-329-21
1-500-329-21
1-500-329-21
FERRITE
FERRITE
FERRITE
FERRITE
FERRITE
0uH
0uH
0uH
0uH
0uH
FB809
FB810
FB811
FB812
FB813
1-500-329-21
1-500-329-21
1-500-329-21
1-469-185-11
1-469-185-11
FERRITE
FERRITE
FERRITE
FERRITE
FERRITE
0uH
0uH
0uH
0uH
0uH
FB814
FB815
FB816
FB817
FB818
1-500-329-21
1-500-329-21
1-500-329-21
1-500-329-21
1-500-329-21
FERRITE
FERRITE
FERRITE
FERRITE
FERRITE
0uH
0uH
0uH
0uH
0uH
FB819
FB820
FB821
FB823
FB827
1-500-329-21
1-500-329-21
1-500-329-21
1-216-864-11
1-469-179-21
FERRITE
FERRITE
FERRITE
SHORT
FERRITE
0uH
0uH
0uH
0
0uH
FB828
FB829
FB830
* FB831
1-469-179-21
1-469-179-21
1-469-179-21
1-469-532-21
FERRITE
FERRITE
FERRITE
FERRITE
0uH
0uH
0uH
0uH
73
ZS-M30
MAIN
Ref. No.
FB880
Part No.
Description
1-500-329-21 FERRITE
Remark
0uH
Ref. No.
Part No.
Description
Remark
R110
R111
1-216-821-11 METAL CHIP
1-216-827-11 METAL CHIP
1K
3.3K
5%
5%
1/16W
1/16W
R112
R113
R114
R115
R116
1-216-821-11
1-216-841-11
1-216-835-11
1-216-789-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
47K
15K
2.2
100
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R117
R118
R119
R120
R121
1-216-845-11
1-216-864-91
1-216-789-11
1-216-821-11
1-216-833-11
METAL CHIP
SHORT
METAL CHIP
METAL CHIP
METAL CHIP
100K
0
2.2
1K
10K
5%
1/16W
5%
5%
5%
1/16W
1/16W
1/16W
R122
R123
R124
R125
R126
1-216-821-11
1-216-845-11
1-216-827-11
1-216-843-11
1-216-829-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
100K
3.3K
68K
4.7K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R128
R201
R202
R203
R204
1-216-837-11
1-216-817-11
1-216-823-11
1-216-821-11
1-216-825-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
22K
470
1.5K
1K
2.2K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R205
R206
R207
R208
R210
1-216-823-11
1-216-851-11
1-216-857-11
1-216-837-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1.5K
330K
1M
22K
1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R211
R212
R213
R214
R215
1-216-827-11
1-216-821-11
1-216-841-11
1-216-835-11
1-216-789-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
3.3K
1K
47K
15K
2.2
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R216
R217
R218
R219
R220
1-216-809-11
1-216-845-11
1-216-864-91
1-216-789-11
1-216-821-11
METAL CHIP
METAL CHIP
SHORT
METAL CHIP
METAL CHIP
100
100K
0
2.2
1K
5%
5%
1/16W
1/16W
5%
5%
1/16W
1/16W
R221
R222
R223
R224
R225
1-216-833-11
1-216-821-11
1-216-845-11
1-216-827-11
1-216-843-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
1K
100K
3.3K
68K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R226
R228
R302
R303
R304
1-216-829-11
1-216-837-11
1-216-833-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
22K
10K
10K
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R306
R309
R312
R314
R318
1-216-809-11
1-216-805-11
1-216-839-11
1-216-821-11
1-216-857-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
47
33K
1K
1M
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R319
R320
R323
R324
R325
1-216-821-11
1-216-821-11
1-216-817-11
1-216-821-11
1-216-817-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
470
1K
470
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
< IC >
IC301
IC302
IC303
IC305
IC801
8-759-426-51
8-759-669-03
8-759-426-51
8-759-278-58
8-752-921-18
IC
IC
IC
IC
IC
BA5417
LC75342
BA5417
NJM4558V-TE2
CXP740096-059Q
IC802
IC803
IC804
8-759-646-52 IC KIA7805API
8-759-486-73 IC XC62FP3302PR
8-759-649-23 IC XC61CN2802PR
< JUMPER >
JC804
1-216-864-91 SHORT
0
< JUMPER RESISTOR >
JW876
1-249-401-11 CARBON
47
5%
1/4W
< TRANSISTOR >
Q101
Q102
Q106
Q111
Q201
8-729-027-56
8-729-120-28
8-729-920-31
8-729-027-56
8-729-027-56
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC143TKA-T146
2SC1623-L5L6
DTC343TK
DTC143TKA-T146
DTC143TKA-T146
Q202
Q206
Q211
Q302
Q305
8-729-120-28
8-729-920-31
8-729-027-56
8-729-027-26
8-729-027-46
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC1623-L5L6
DTC343TK
DTC143TKA-T146
DTA114YKA-T146
DTC114YKA-T146
Q310
Q312
Q313
Q801
Q802
8-729-027-26
8-729-027-24
8-729-027-26
8-729-903-10
8-729-027-46
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTA114YKA-T146
DTA114TKA-T146
DTA114YKA-T146
FMW1
DTC114YKA-T146
Q804
Q805
Q806
Q807
Q808
8-729-052-52
8-729-052-52
8-729-903-46
8-729-027-46
8-729-027-26
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
KTC2026Y
KTC2026Y
2SB1132-P
DTC114YKA-T146
DTA114YKA-T146
Q809
Q810
Q811
Q812
Q816
8-729-027-46
8-729-021-82
8-729-027-46
8-729-903-46
8-729-027-46
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC114YKA-T146
2SD2396K
DTC114YKA-T146
2SB1132-P
DTC114YKA-T146
Q817
Q818
Q819
8-729-027-26 TRANSISTOR
8-729-052-52 TRANSISTOR
8-729-027-26 TRANSISTOR
DTA114YKA-T146
KTC2026Y
DTA114YKA-T146
< RESISTOR >
R101
R102
R103
R104
R105
1-216-817-11
1-216-823-11
1-216-821-11
1-216-825-11
1-216-823-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
470
1.5K
1K
2.2K
1.5K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R106
R107
R108
1-216-851-11 METAL CHIP
1-216-857-11 METAL CHIP
1-216-837-11 METAL CHIP
330K
1M
22K
5%
5%
5%
1/16W
1/16W
1/16W
74
ZS-M30
MAIN
Ref. No.
Part No.
Description
R326
R327
R328
R451
R452
1-216-837-11
1-216-833-11
1-216-833-11
1-249-411-11
1-249-413-11
METAL CHIP
METAL CHIP
METAL CHIP
CARBON
CARBON
22K
10K
10K
330
470
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/4W
1/4W
Remark
R453
R454
R455
R456
R457
1-216-821-11
1-216-839-11
1-216-837-11
1-216-833-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
33K
22K
10K
47K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R459
R801
R802
R803
R804
1-216-833-11
1-216-821-11
1-216-821-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
1K
1K
1K
1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R805
R806
R807
R808
R809
1-216-821-11
1-216-821-11
1-216-821-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
1K
1K
1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R811
R812
R813
R814
R816
1-216-821-11
1-216-821-11
1-216-821-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
1K
1K
1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R817
R818
R819
R820
R821
1-216-817-11
1-216-817-11
1-216-821-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
470
470
1K
1K
1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R822
R823
R824
R825
R826
1-216-829-11
1-216-817-11
1-216-821-11
1-216-817-11
1-216-817-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
470
1K
470
470
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R827
R829
R831
R832
R833
1-216-827-11
1-216-829-11
1-216-821-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
3.3K
4.7K
1K
1K
1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R834
R835
R836
R837
R839
1-216-821-11
1-216-821-11
1-216-821-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
1K
1K
1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R841
R842
R843
R844
R845
1-216-821-11
1-216-821-11
1-216-821-11
1-216-817-11
1-216-817-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
1K
470
470
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R846
R847
R848
R850
R851
1-216-821-11
1-216-821-11
1-216-821-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
1K
1K
1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R852
R853
R854
1-216-821-11 METAL CHIP
1-216-809-11 METAL CHIP
1-216-805-11 METAL CHIP
1K
100
47
5%
5%
5%
1/16W
1/16W
1/16W
Ref. No.
Part No.
Description
MD
Remark
R855
R856
1-216-817-11 METAL CHIP
1-216-821-11 METAL CHIP
470
1K
5%
5%
1/16W
1/16W
R857
R858
R859
R860
R861
1-216-805-11
1-216-821-11
1-216-821-11
1-216-833-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47
1K
1K
10K
1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R862
R863
R864
R865
R866
1-216-841-11
1-216-821-11
1-216-833-11
1-216-829-11
1-216-829-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
1K
10K
4.7K
4.7K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R867
R868
R869
R870
R873
1-216-829-11
1-216-829-11
1-216-829-11
1-216-829-11
1-216-817-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
4.7K
4.7K
4.7K
470
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R874
R875
R878
R881
R882
1-216-813-11
1-216-841-11
1-216-833-11
1-216-821-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
220
47K
10K
1K
100
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R883
R884
R885
R886
R887
1-216-833-11
1-216-835-11
1-216-821-11
1-216-841-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
15K
1K
47K
1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R890
R891
R892
R893
R894
1-216-817-11
1-216-813-11
1-216-821-11
1-216-821-11
1-216-829-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
470
220
1K
1K
4.7K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R898
R899
1-216-821-11 METAL CHIP
1-249-413-11 CARBON
1K
470
5%
5%
1/16W
1/4W
< VIBRATOR >
X801
1-767-697-11 VIBRATOR, CRYSTAL (32.768KHz)
X802
1-781-598-21 VIBRATOR, CERAMIC (8MHz)
**************************************************************
A-3322-905-A MD BOARD, COMPLETE
********************
< CAPACITOR >
C501
C502
C503
C505
C506
1-126-791-11
1-107-826-11
1-126-791-11
1-162-970-11
1-164-156-11
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
10uF
0.1uF
10uF
0.01uF
0.1uF
20%
10%
20%
10%
C508
C509
C510
C511
C512
1-164-156-11
1-126-791-11
1-126-791-11
1-164-156-11
1-164-227-11
CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
0.1uF
10uF
10uF
0.1uF
0.022uF
10%
25V
16V
16V
25V
25V
C513
C514
C515
C516
1-164-156-11
1-162-970-11
1-126-791-11
1-126-791-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
0.1uF
0.01uF
10uF
10uF
10%
20%
20%
25V
25V
16V
16V
20%
20%
16V
16V
16V
25V
25V
75
ZS-M30
MD
Ref. No.
Part No.
Description
Remark
C517
1-165-176-11 CERAMIC CHIP
0.047uF
10%
16V
C518
C519
C520
C521
C522
1-162-964-11
1-162-970-11
1-164-227-11
1-162-968-11
1-115-467-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.01uF
0.022uF
0.0047uF
0.22uF
10%
10%
10%
10%
10%
50V
25V
25V
50V
10V
C523
C524
C525
C526
C527
1-164-156-11
1-126-791-11
1-164-156-11
1-164-227-11
1-162-970-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
10uF
0.1uF
0.022uF
0.01uF
C528
C529
C530
C531
C532
1-162-968-11
1-162-970-11
1-109-982-11
1-164-156-11
1-165-176-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0047uF
0.01uF
1uF
0.1uF
0.047uF
C533
C534
C536
C537
C538
1-126-382-11
1-163-021-91
1-124-779-00
1-164-156-11
1-164-156-11
ELECT
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
100uF
0.01uF
10uF
0.1uF
0.1uF
20%
10%
20%
6.3V
50V
16V
25V
25V
C539
C540
C541
C542
C544
1-126-382-11
1-164-156-11
1-162-927-11
1-162-927-11
1-162-927-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100uF
0.1uF
100PF
100PF
100PF
20%
5%
5%
5%
6.3V
25V
50V
50V
50V
C545
C546
C547
C548
C549
1-162-970-11
1-164-227-11
1-125-891-11
1-162-915-11
1-162-915-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.022uF
0.47uF
10PF
10PF
10%
10%
10%
0.5PF
0.5PF
25V
25V
10V
50V
50V
C550
C551
C552
C553
C554
1-162-968-11
1-163-038-11
1-162-927-11
1-125-891-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0047uF
0.1uF
100PF
0.47uF
0.01uF
10%
50V
25V
50V
10V
25V
C555
C556
C557
C558
C559
1-164-156-11
1-126-791-11
1-164-156-11
1-164-156-11
1-126-382-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.1uF
10uF
0.1uF
0.1uF
100uF
C560
C601
C602
C603
C604
1-126-791-11
1-162-927-11
1-162-927-11
1-164-156-11
1-164-156-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
10uF
100PF
100PF
0.1uF
0.1uF
20%
5%
5%
C605
C606
C607
C608
C609
1-162-927-11
1-164-156-11
1-162-927-11
1-164-156-11
1-164-156-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100PF
0.1uF
100PF
0.1uF
0.1uF
5%
C610
C611
C612
C613
C614
1-126-205-11
1-164-156-11
1-162-964-11
1-126-246-11
1-107-826-11
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
47uF
0.1uF
0.001uF
220uF
0.1uF
20%
10%
20%
10%
6.3V
25V
50V
4V
16V
C615
1-162-964-11 CERAMIC CHIP
0.001uF
10%
50V
76
20%
10%
10%
10%
10%
10%
10%
5%
10%
10%
20%
20%
5%
25V
16V
25V
25V
25V
50V
25V
10V
25V
16V
25V
16V
25V
25V
6.3V
16V
50V
50V
25V
25V
50V
25V
50V
25V
25V
Ref. No.
Part No.
Description
C616
C617
C618
C619
1-162-964-11
1-162-927-11
1-162-927-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
100PF
100PF
0.01uF
10%
5%
5%
10%
50V
50V
50V
25V
Remark
C620
C621
C622
C623
C624
1-109-982-11
1-162-927-11
1-162-927-11
1-124-779-00
1-109-982-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
1uF
100PF
100PF
10uF
1uF
10%
5%
5%
20%
10%
10V
50V
50V
16V
10V
C625
C626
C627
C629
C630
1-164-156-11
1-124-589-11
1-162-970-11
1-164-156-11
1-124-589-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.1uF
47uF
0.01uF
0.1uF
47uF
C631
C632
1-162-970-11 CERAMIC CHIP
1-469-125-21 FERRITE
0.01uF
0uH
20%
25V
16V
25V
25V
16V
10%
25V
20%
10%
< CONNECTOR >
CN501
* CN502
CN503
* CN601
* CN602
CN603
1-766-833-21
1-794-627-21
1-770-692-11
1-580-055-21
1-580-055-21
CONNECTOR, FFC/FPC (ZIF) 21P
CONNECTOR, FFC/FPC 7P
CONNECTOR, FFC/FPC 9P
PIN, CONNECTOR (SMD) 2P
PIN, CONNECTOR (SMD) 2P
1-770-705-11 CONNECTOR, FFC/FPC 22P
< DIODE >
D501
8-719-988-61 DIODE 1SS355TE-17
< FERRITE BEAD >
FB501
FB502
FB503
FB504
FB505
1-469-179-21
1-469-125-21
1-412-987-31
1-412-987-31
1-412-987-31
FERRITE
FERRITE
INDUCTOR
INDUCTOR
INDUCTOR
0uH
0uH
4.7uH
4.7uH
4.7uH
FB506
FB507
FB508
FB601
FB602
1-412-987-31
1-216-864-91
1-216-864-91
1-216-864-91
1-216-864-91
INDUCTOR
SHORT
SHORT
SHORT
SHORT
4.7uH
0
0
0
0
FB603
FB604
FB605
FB606
FB607
1-216-864-91
1-469-125-21
1-469-125-21
1-469-125-21
1-469-125-21
SHORT
FERRITE
FERRITE
FERRITE
FERRITE
0
0uH
0uH
0uH
0uH
FB609
FB610
FB611
FB612
FB613
1-469-125-21
1-469-125-21
1-469-125-21
1-469-125-21
1-469-125-21
FERRITE
FERRITE
FERRITE
FERRITE
FERRITE
0uH
0uH
0uH
0uH
0uH
* FB614
FB615
FB616
FB617
FB618
1-469-532-21
1-469-125-21
1-469-125-21
1-469-125-21
1-469-125-21
FERRITE
FERRITE
FERRITE
FERRITE
FERRITE
0uH
0uH
0uH
0uH
0uH
1-469-125-21 FERRITE
1-469-125-21 FERRITE
1-500-329-21 FERRITE
0uH
0uH
0uH
FB619
FB620
FB621
ZS-M30
MD
Ref. No.
Part No.
Description
Remark
FB622
FB623
1-469-125-21 FERRITE
1-469-125-21 FERRITE
0uH
0uH
FB624
FB625
FB626
FB627
FB628
1-469-125-21
1-469-125-21
1-469-125-21
1-469-125-21
1-469-125-21
FERRITE
FERRITE
FERRITE
FERRITE
FERRITE
0uH
0uH
0uH
0uH
0uH
FB629
1-469-125-21 FERRITE
0uH
< FILTER >
FL501
FL502
FL503
FL601
FL602
1-234-117-21
1-234-117-21
1-234-117-21
1-239-899-21
1-239-899-21
FILTER, CHIP EMI
FILTER, CHIP EMI
FILTER, CHIP EMI
FILTER, CHIP EMI
FILTER, CHIP EMI
FL603
FL604
FL605
FL606
FL607
1-234-121-21
1-234-121-21
1-234-177-21
1-234-177-21
1-234-177-21
FILTER, CHIP EMI
FILTER, CHIP EMI
FILTER, CHIP EMI
FILTER, CHIP EMI
FILTER, CHIP EMI
FL608
FL609
FL610
FL611
FL612
1-234-121-21
1-234-177-21
1-234-121-21
1-234-126-21
1-234-126-21
FILTER, CHIP EMI
FILTER, CHIP EMI
FILTER, CHIP EMI
FILTER, CHIP EMI
FILTER, CHIP EMI
Ref. No.
Part No.
Description
Remark
< COIL >
* L501
L502
L503
L504
L505
1-469-532-21
1-469-967-21
1-414-771-91
1-414-398-11
1-414-398-11
FERRITE
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
0uH
10uH
10uH
10uH
10uH
L506
L507
L508
L509
L510
1-469-967-21
1-414-404-11
1-414-404-11
1-414-771-91
1-414-398-11
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
10uH
100uH
100uH
10uH
10uH
L511
L512
L601
L602
L603
1-216-295-11
1-469-967-21
1-469-967-21
1-469-967-21
1-414-398-11
SHORT
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
0
10uH
10uH
10uH
10uH
L604
L605
L606
L607
L608
1-414-398-11
1-414-771-91
1-469-967-21
1-216-295-11
1-414-398-11
INDUCTOR
INDUCTOR
INDUCTOR
SHORT
INDUCTOR
10uH
10uH
10uH
0
10uH
L610
L611
L612
L613
1-216-295-11
1-416-107-21
1-414-398-11
1-414-398-11
SHORT
INDUCTOR
INDUCTOR
INDUCTOR
0
0uH
10uH
10uH
< IC >
< TRANSISTOR >
IC501
IC502
IC503
IC504
IC505
8-759-430-25
8-752-080-95
8-759-523-37
8-752-389-44
8-759-653-36
IC
IC
IC
IC
IC
BH6511FS-E2
CXA2523AR
TC74ACT08FT (EL)
CXD2654R
GLT441M04-70TC
Q501
Q502
Q503
Q504
Q505
8-729-402-93
8-729-903-10
8-729-403-35
8-729-402-93
8-729-026-53
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
UN5214
FMW1
UN5113
UN5214
2SA1576A-T106-QR
IC506
IC601
IC602
IC603
IC604
8-759-460-72
8-759-697-89
8-759-040-83
8-759-640-39
8-759-561-36
IC
IC
IC
IC
IC
BA033FP-E2
M30620MCA-A73FP
BA6287F-T1
BR24C02F-WE2
PCM3003E/T2
Q506
Q507
Q508
Q601
Q602
8-729-903-46
8-729-403-35
8-729-031-43
8-729-031-43
8-729-028-99
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SB1132-P
UN5113
IMD9A-T108
IMD9A-T108
DTC114YUA-T106
Q603
Q604
Q605
Q606
Q607
8-729-101-07
8-729-907-03
8-729-027-46
8-729-904-87
8-729-031-43
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SB798-DL
FMG5
DTC114YKA-T146
2SB1197K-R
IMD9A-T108
< JUMPER >
JC501
JC502
JC503
JC504
JC505
1-216-295-11
1-216-295-11
1-216-295-11
1-216-295-11
1-216-295-11
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
JC506
JC507
JC508
JC510
JC511
1-216-295-11
1-216-295-11
1-216-295-11
1-216-295-11
1-216-295-11
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
R501
R502
R503
R504
R505
1-216-829-11
1-216-821-11
1-216-853-11
1-216-863-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
RES-CHIP
METAL CHIP
4.7K
1K
470K
3.3M
1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
JC512
JC514
JC516
JC601
JC602
1-216-295-11
1-216-295-11
1-216-295-11
1-216-295-11
1-216-295-11
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
R506
R508
R509
R510
R511
1-249-387-11
1-216-821-11
1-216-841-11
1-216-833-11
1-216-845-11
CARBON
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
3.3
1K
47K
10K
100K
5%
5%
5%
5%
5%
1/4W
1/16W
1/16W
1/16W
1/16W
JC603
JC604
JC605
1-216-864-91 SHORT
1-216-864-91 SHORT
1-216-295-11 SHORT
0
0
0
R512
R513
R514
R515
1-216-825-11
1-216-853-11
1-216-829-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.2K
470K
4.7K
10K
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
< RESISTOR >
77
ZS-M30
MD
Ref. No.
Part No.
Description
Remark
R516
1-216-819-11 METAL CHIP
680
5%
1/16W
R517
R518
R519
R520
R521
1-216-833-11
1-216-833-11
1-216-845-11
1-216-833-11
1-216-829-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
100K
10K
4.7K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R522
R523
R524
R525
R526
1-216-833-11
1-216-827-11
1-216-845-11
1-216-833-11
1-216-864-91
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
SHORT
10K
3.3K
100K
10K
0
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
R527
R528
R529
R530
R531
1-216-837-11
1-216-839-11
1-216-825-11
1-216-825-11
1-216-864-91
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
SHORT
22K
33K
2.2K
2.2K
0
5%
5%
5%
5%
R532
R533
R534
R535
R536
1-216-815-11
1-216-819-11
1-216-841-11
1-216-809-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
330
680
47K
100
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R537
R538
R539
R540
R541
1-216-833-11
1-216-864-91
1-216-845-11
1-216-811-11
1-216-821-11
METAL CHIP
SHORT
METAL CHIP
METAL CHIP
METAL CHIP
10K
0
100K
150
1K
5%
1/16W
5%
5%
5%
1/16W
1/16W
1/16W
R542
R543
R544
R545
R547
1-216-827-11
1-216-821-11
1-216-809-11
1-216-864-91
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
SHORT
METAL CHIP
3.3K
1K
100
0
10K
5%
5%
5%
1/16W
1/16W
1/16W
5%
1/16W
R548
R549
R550
R551
R552
1-216-813-11
1-216-855-11
1-216-833-11
1-216-845-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
220
680K
10K
100K
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R553
R554
R555
R556
R557
1-216-833-11
1-216-833-11
1-216-809-11
1-216-817-11
1-216-817-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
100
470
470
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R558
R559
R562
R601
R602
1-216-817-11
1-216-813-11
1-216-864-91
1-216-833-11
1-216-821-11
METAL CHIP
METAL CHIP
SHORT
METAL CHIP
METAL CHIP
470
220
0
10K
1K
5%
5%
1/16W
1/16W
5%
5%
1/16W
1/16W
R603
R604
R605
R606
R607
1-216-833-11
1-216-049-11
1-216-833-11
1-216-049-11
1-216-833-11
METAL CHIP
RES-CHIP
METAL CHIP
RES-CHIP
METAL CHIP
10K
1K
10K
1K
10K
5%
5%
5%
5%
5%
1/16W
1/10W
1/16W
1/10W
1/16W
R608
R609
R610
R611
R612
1-216-049-11
1-216-853-11
1-216-853-11
1-216-853-11
1-216-853-11
RES-CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
470K
470K
470K
470K
5%
5%
5%
5%
5%
1/10W
1/16W
1/16W
1/16W
1/16W
78
1/16W
1/16W
1/16W
1/16W
Ref. No.
Part No.
Description
R613
R614
R616
R617
R618
1-216-853-11
1-216-853-11
1-216-833-11
1-216-049-11
1-216-049-11
METAL CHIP
METAL CHIP
METAL CHIP
RES-CHIP
RES-CHIP
470K
470K
10K
1K
1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/10W
1/10W
Remark
R619
R620
R621
R622
R623
1-216-845-11
1-216-845-11
1-216-857-11
1-216-833-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
100K
1M
10K
47K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R624
R625
R626
R627
R628
1-216-841-11
1-216-833-11
1-216-025-11
1-216-845-11
1-216-864-91
METAL CHIP
METAL CHIP
RES-CHIP
METAL CHIP
SHORT
47K
10K
100
100K
0
5%
5%
5%
5%
1/16W
1/16W
1/10W
1/16W
R629
R630
R631
R632
R633
1-216-845-11
1-216-833-11
1-216-845-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
10K
100K
10K
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R635
R637
R638
R639
R640
1-216-845-11
1-216-845-11
1-216-809-11
1-216-809-11
1-216-829-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
100K
100
100
4.7K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R641
R642
R643
R644
R645
1-216-817-11
1-216-841-11
1-216-833-11
1-216-833-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
470
47K
10K
10K
1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R646
R647
R648
R649
R650
1-216-821-11
1-216-821-11
1-216-821-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
1K
10K
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R651
R652
R653
R654
R655
1-216-821-11
1-216-821-11
1-500-329-21
1-216-817-11
1-216-073-00
METAL CHIP
METAL CHIP
FERRITE
METAL CHIP
METAL CHIP
1K
1K
0uH
470
10K
5%
5%
1/16W
1/16W
5%
5%
1/16W
1/10W
R656
R658
R659
R660
R661
1-216-841-11
1-216-864-91
1-216-821-11
1-216-821-11
1-216-845-11
METAL CHIP
SHORT
METAL CHIP
METAL CHIP
METAL CHIP
47K
0
1K
1K
100K
5%
1/16W
5%
5%
5%
1/16W
1/16W
1/16W
< SWITCH >
S501
1-762-596-21 SWITCH, PUSH (1 KEY) (LIMIT)
< VIBRATOR >
X501
1-760-173-11 VIBRATOR, CRYSTAL (45.1584MHz)
X601
1-781-155-21 VIBRATOR, CERAMIC (12MHz)
**************************************************************
ZS-M30
POWER
Ref. No.
Part No.
Description
Remark
1-679-406-21 POWER BOARD
*************
Ref. No.
C564
C565
Part No.
1-162-995-11
1-162-995-11
1-162-995-11
1-162-995-11
1-162-995-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.022uF
0.022uF
0.022uF
0.022uF
0.022uF
50V
50V
50V
50V
50V
C906
1-162-995-11 CERAMIC CHIP
0.022uF
50V
* CN504
CN505
Remark
10uF
0.1uF
10%
10%
6.3V
16V
1-778-774-11 HOUSING, CONNECTOR (FPC) 4P
1-784-683-11 CONNECTOR, FFC/FPC 9P
< DIODE >
D502
D503
8-719-046-86 DIODE F1J6TP
8-719-046-86 DIODE F1J6TP
< CONNECTOR >
< JUMPER >
1-785-654-11 PIN, CONNECTOR (PC BOARD) 2P
JC509
1-216-864-91 SHORT
< DIODE >
0
< COIL >
D901
D902
D903
D904
D905
8-719-046-07
8-719-046-07
8-719-046-07
8-719-046-07
8-719-046-07
DIODE
DIODE
DIODE
DIODE
DIODE
2A02M
2A02M
2A02M
2A02M
2A02M
D906
D907
D908
D910
D911
8-719-046-07
8-719-046-07
8-719-046-07
8-719-988-61
8-719-988-61
DIODE
DIODE
DIODE
DIODE
DIODE
2A02M
2A02M
2A02M
1SS355TE-17
1SS355TE-17
L513
1-414-398-11 INDUCTOR
10uH
< TRANSISTOR >
Q509
Q510
8-729-017-65 TRANSISTOR
8-729-018-75 TRANSISTOR
2SK1764KYTR
2SJ278MYTR
< RESISTOR >
R560
R561
1-216-841-11 METAL CHIP
1-216-841-11 METAL CHIP
< FUSE >
! F901
! F902
SW(L)
< CONNECTOR >
C901
C902
C903
C904
C905
* CN902
Description
1-125-817-11 CERAMIC CHIP
1-107-826-11 CERAMIC CHIP
< CAPACITOR >
REC
47K
47K
5%
5%
1/16W
1/16W
< SWITCH >
1-532-465-51 FUSE,TIME LAG 3.15A/250V
1-532-503-51 FUSE,TIME LAG 1.6A/250V
S502
1-771-783-21 SWITCH, PUSH LEVER (REC POSOTION)
S504
1-771-783-21 SWITCH, PUSH LEVER (PLAY POSOTION)
**************************************************************
< FUSE HOLDER >
FH901
FH902
FH903
FH904
1-533-233-31
1-533-233-31
1-533-233-31
1-533-233-31
1-679-403-21 SW (L) BOARD
************
HOLDER, FUSE
HOLDER, FUSE
HOLDER, FUSE
HOLDER, FUSE
3-831-441-11 CUSHION (B)
< HOLDER >
< JACK >
* CH402
0 J901
1-815-155-11 HOLDER, CABLE 4P
1-526-838-11 INLET, AC 2P ( - AC IN)
< RESISTOR >
< LINE FILTER >
0 LF901
R413
R414
R415
R416
1-402-663-11 TRANSFORMER, LINE FILTER (LFT)
< RESISTOR >
R901
R902
1-216-833-11 METAL CHIP
1-216-841-11 METAL CHIP
10K
47K
5%
5%
1/16W
1/16W
< TRANSFORMER >
0 T901
1-435-872-11 TRANSFORMER, POWER
**************************************************************
A-3322-907-A REC BOARD, COMPLETE
********************
1-127-677-21 CERAMIC CHIP
1-119-667-11 CERAMIC CHIP
1-107-826-11 CERAMIC CHIP
0.001uF
22uF
0.1uF
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1.5K
1.5K
4.7K
1.5K
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
< SWITCH >
S411
S412
S413
S414
S415
1-786-050-21
1-786-050-21
1-786-050-21
1-786-050-21
1-786-050-21
SWITCH, KEY BOARD (MDu)
SWITCH, KEY BOARD (MDx)
SWITCH, KEY BOARD (CDu)
SWITCH, KEY BOARD (CDx)
SWITCH, KEY BOARD (RADIO BAND,AUTO
PRESET)
S416
1-786-050-21 SWITCH, KEY BOARD (GAME(LINE),LINE
LEVEL)
**************************************************************
< CAPACITOR >
C561
C562
C563
1-216-823-11
1-216-823-11
1-216-829-11
1-216-823-11
10%
10%
250V
10V
16V
The components identified by mark 0
or dotted line with mark 0 are critical
for safety.
Replace only with part number specified.
79
ZS-M30
SW(R)
Ref. No.
TOP
Part No.
TUNER
Description
Remark
1-679-402-21 SW (R) BOARD
*************
Ref. No.
Part No.
Description
Remark
R406
R407
R408
1-216-829-11 METAL CHIP
1-216-833-11 METAL CHIP
1-216-833-11 METAL CHIP
4.7K
10K
10K
5%
5%
5%
1/16W
1/16W
1/16W
R409
R410
R411
1-216-829-11 METAL CHIP
1-216-823-11 METAL CHIP
1-216-823-11 METAL CHIP
4.7K
1.5K
1.5K
5%
5%
5%
1/16W
1/16W
1/16W
< CAPACITOR >
C401
C402
C403
1-124-259-11 ELECT
1-162-968-11 CERAMIC CHIP
1-162-968-11 CERAMIC CHIP
4.7uF
20%
0.0047uF 10%
0.0047uF 10%
16V
50V
50V
< SWITCH >
< HOLDER >
* CH401
S401
S402
S403
1-565-385-11 HOLDER, CABLE 4P
< TRANSISTOR >
Q401
S404
S405
8-729-027-43 TRANSISTOR DTC144EKA-T146
S406
1-786-050-21 SWITCH, KEY BOARD (VOLUME+)
S407
1-786-050-21 SWITCH, KEY BOARD (VOLUME-)
S408
1-786-050-21 SWITCH, KEY BOARD (MODE)
S409
1-786-050-21 SWITCH, KEY BOARD (PANORAMA SOUND)
S410
1-786-050-21 SWITCH, KEY BOARD (SOUND MEGA BASS)
**************************************************************
< CONNECTOR >
CN402
1-770-516-31 PIN, CONNECTOR (PC BOARD) 8P
< IC >
IC401
1-786-050-21 SWITCH, KEY BOARD (OPERATE)
1-786-050-21 SWITCH, KEY BOARD (HIGH SPEED)
1-786-050-21 SWITCH, KEY BOARD (SYNCHRO
REC,CDNMD)
1-786-050-21 SWITCH, KEY BOARD (REC,REC MODE)
1-786-050-21 SWITCH, KEY BOARD (STANDBY)
8-749-016-97 IC NJL62H400A
A-3347-168-A TUNER BOARD, COMPLETE
**********************
< RESISTOR >
R412
R417
R418
R419
R420
1-216-839-11
1-216-823-11
1-216-829-11
1-216-833-11
1-216-823-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
33K
1.5K
4.7K
10K
1.5K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R421
R422
R423
R431
1-216-823-11
1-216-829-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1.5K
4.7K
10K
10K
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
< CAPACITOR >
C1
C2
C3
C4
C5
1-162-964-11
1-162-923-11
1-162-970-11
1-162-970-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
47PF
0.01uF
0.01uF
0.01uF
10%
5%
10%
10%
10%
50V
50V
25V
25V
25V
C6
C7
C8
C9
C10
1-162-915-11
1-165-176-11
1-164-230-11
1-162-927-11
1-162-923-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
10PF
0.047uF
220PF
100PF
47PF
0.5PF
10%
5%
5%
5%
50V
16V
50V
50V
50V
SWITCH, KEY BOARD (DISPLAY)
SWITCH, KEY BOARD (TUNE+,M k)
SWITCH, KEY BOARD (TUNE-,m K)
SWITCH, KEY BOARD (EDIT)
SWITCH, KEY BOARD (DEL,CLOCK/SLEEP/
TIMER)
C11
C12
C13
C14
C15
1-162-918-11
1-164-227-11
1-164-227-11
1-104-664-11
1-126-935-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
18PF
0.022uF
0.022uF
47uF
470uF
5%
10%
10%
20%
20%
50V
25V
25V
10V
10V
S422
1-786-050-21 SWITCH, KEY BOARD (YES,ENTER)
S423
1-786-050-21 SWITCH, KEY BOARD (NO,CANCEL)
S424
1-786-050-21 SWITCH, KEY BOARD ((MD)Z)
S425
1-771-915-11 SWITCH, ROTARY (JOG)
**************************************************************
C16
C17
C18
C19
C20
1-164-227-11
1-164-227-11
1-115-156-11
1-125-891-11
1-115-156-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.022uF
0.022uF
1uF
0.47uF
1uF
10%
10%
25V
25V
10V
10V
10V
C21
C22
C23
C24
C25
1-162-917-11
1-162-970-11
1-162-968-11
1-162-970-11
1-162-968-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
15PF
0.01uF
0.0047uF
0.01uF
0.0047uF
5%
10%
10%
10%
10%
50V
25V
50V
25V
50V
C26
C27
C28
C29
C30
1-125-891-11
1-162-970-11
1-128-551-11
1-164-227-11
1-126-963-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
0.47uF
0.01uF
22uF
0.022uF
4.7uF
10%
10%
20%
10%
20%
10V
25V
25V
25V
50V
C32
C33
C34
C35
1-126-934-11
1-162-970-11
1-162-915-11
1-162-915-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
220uF
0.01uF
10PF
10PF
20%
10%
0.5PF
0.5PF
10V
25V
50V
50V
< SWITCH >
S417
S418
S419
S420
S421
1-786-050-21
1-786-050-21
1-786-050-21
1-786-050-21
1-786-050-21
1-679-401-21 TOP BOARD
**********
< CONNECTOR >
CN401
1-770-540-31 PIN, CONNECTOR (PC BOARD) 6P
< DIODE >
D402
D403
8-719-941-07 LED SLC-22VR3 (HIGH SPEED)
8-719-077-29 LED SLC-22MG3F (PANORAMA SOUND)
< RESISTOR >
R404
R405
80
10%
1-216-823-11 METAL CHIP
1-216-823-11 METAL CHIP
1.5K
1.5K
5%
5%
1/16W
1/16W
ZS-M30
TUNER
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
< COIL >
C36
1-162-968-11 CERAMIC CHIP
0.0047uF 10%
50V
C37
C38
C39
C40
C41
1-162-962-11
1-162-962-11
1-162-927-11
1-126-964-11
1-164-227-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
470PF
470PF
100PF
10uF
0.022uF
10%
10%
5%
20%
10%
50V
50V
50V
50V
25V
L1
L2
L3
L4
L5
1-424-716-11
1-424-717-11
1-416-991-11
1-416-129-11
1-411-959-11
C43
C44
C45
C46
C47
1-162-925-11
1-165-176-11
1-165-176-11
1-162-925-11
1-164-230-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
68PF
0.047uF
0.047uF
68PF
220PF
5%
10%
10%
5%
5%
50V
16V
16V
50V
50V
L6
L7
L8
1-419-465-11 COIL (FM DET) (FM IF)
1-412-979-21 INDUCTOR
1uH
1-410-071-11 INDUCTOR
10MH
C49
C50
C51
C52
C53
1-165-176-11
1-162-927-11
1-165-176-11
1-162-970-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.047uF
100PF
0.047uF
0.01uF
0.01uF
10%
5%
10%
10%
10%
16V
50V
16V
25V
25V
Q1
Q2
Q3
Q4
Q5
8-729-119-32
8-729-920-31
8-729-920-38
8-729-931-02
8-729-027-26
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SK193-E
DTC343TK
2SC2059K-N
2SC2413KQ
DTA114YKA-T146
C60
1-164-230-11 CERAMIC CHIP
220PF
5%
50V
Q6
8-729-027-26 TRANSISTOR
DTA114YKA-T146
< TRANSISTOR >
< RESISTOR >
< FILTER >
CF1
CF2
CF3
1-781-407-11 FILTER, CERAMIC
1-781-407-11 FILTER, CERAMIC
1-781-344-12 FILTER, AM CERAMIC
< CONNECTOR >
* CN1
1-785-662-11 PIN, CONNECTOR (PC BOARD) 10P
< TRIMMER >
CT1
CT2
CT3
CT4
COIL, AIR-CORE (FM TRACKING)
COIL, AIR-CORE
COIL, AM ANT (MW TRACKING)
COIL, LW ANT (LW TRACKING)
COIL, AM OSC (MW FREQUENCY COVERAGE)
1-141-601-21 CAP, ADJ 10PF (FM TRACKING)
1-141-601-21 CAP, ADJ 10PF (MW TRACKING)
1-141-459-11 CAP, TRIMMER (SEAL TYPE) 45PF
(LW TRACKING)
1-141-459-11 CAP, TRIMMER (SEAL TYPE) 45PF
(LW FREQUENCY COVERAGE)
R1
R2
R3
R4
R5
1-216-845-11
1-216-797-11
1-216-827-11
1-216-835-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
10
3.3K
15K
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R6
R7
R8
R9
R10
1-216-845-11
1-216-839-11
1-216-805-11
1-216-817-11
1-216-801-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
33K
47
470
22
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R11
R12
R13
R14
R15
1-216-827-11
1-216-825-11
1-216-831-11
1-216-821-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
3.3K
2.2K
6.8K
1K
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R16
R17
R18
R19
R20
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
100
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R21
R22
R23
R24
R25
1-216-821-11
1-216-821-11
1-216-809-11
1-216-829-11
1-216-829-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
100
4.7K
4.7K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R26
R27
R28
R29
R30
R31
R32
R33
R34
R35
1-216-819-11
1-216-837-11
1-216-819-11
1-216-813-11
1-216-829-11
1-216-833-11
1-216-833-11
1-216-829-11
1-216-829-11
1-216-837-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
680
22K
680
220
4.7K
10K
10K
4.7K
4.7K
22K
5%
5%
5%
5%
5%
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
R36
1-216-837-11 METAL CHIP
22K
5%
1/16W
< DIODE >
D1
D2
D3
D4
D5
8-719-076-71
8-719-076-71
8-719-050-69
8-719-988-61
8-719-988-61
DIODE
DIODE
DIODE
DIODE
DIODE
KV1471ETR
KV1471ETR
KV1520N
1SS355TE-17
1SS355TE-17
D6
D7
D8
D9
D10
8-719-988-61
8-719-988-61
8-719-988-61
8-719-988-61
8-719-978-04
DIODE
DIODE
DIODE
DIODE
DIODE
1SS355TE-17
1SS355TE-17
1SS355TE-17
1SS355TE-17
DTZ-TT11-3.3B
< FILTER >
FL1
1-236-711-21 FILTER, BAND PASS
< IC >
IC1
8-759-689-35 IC LV23000M-TLM
< JUMPER >
JC2
JC3
1-216-864-91 SHORT
1-216-864-91 SHORT
0
0
81
ZS-M30
Ver 1.1 2001.04
TUNER
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
T1
Remark
1-433-741-11 TRANSFORMER, IF (AM IF)
1-696-819-11 CORD, POWER (Australian)
1-754-102-21 ANTENNA, ROOP (LW.MW)
1-757-404-11 CORD, CONNECTION (AUDIO)(STEREO MINI
PLUG/STEREO MINI PULUG,102cm)
1-769-412-13 CORD, POWER (AEP,UK)
1-770-019-11 ADAPTOR, CONVERSION PLUG 3P (UK)
3-027-153-11 LID, BATTERY CASE (for RMT-CM30AD)
!
< TERMINAL >
TB1
Description
ACCESSORIES & PACKING MATERIALS
********************************
< TRANSFORMER >
1-694-156-11 TERMINAL BOARD (MW/LW ANTENNA)
< VIBRATOR >
!
!
X1
1-760-130-11 VIBRATOR, CRYSTAL (75kHz)
**************************************************************
3-222-390-31 MANUAL, INSTRUCTION (ENGLISH,SPANISH)
(AEP,UK,Australian)
3-222-390-42 MANUAL, INSTRUCTION (FRENCH,GERMAN)
(AEP)
3-222-390-52 MANUAL, INSTRUCTION
(DUTCH,PORTUGUESE) (AEP)
3-222-390-72 MANUAL, INSTRUCTION (SWEDISH,FINNISH)
(AEP)
A-3364-624-A CONNECTION UNIT ASSY(AV CONNECTING
CORD)
MISCELLANEOUS
***************
63
106
112
119
120
1-757-153-11
1-757-152-11
1-471-110-11
1-757-470-11
1-757-154-11
WIRE, PARALLEL (FFC) (8 CORE)
WIRE, PARALLEL (FFC) (6 CORE)
MAGNET
WIRE, PARALLEL (FFC) (16 CORE)
CABLE, FLEXIBLE FLAT (19 CORE)
153
!154
202
203
204
X-2646-381-1 SHASSIS ASSY, MOTOR (MB) (SPINDLE)
(INCLUDING M901)
8-848-483-05 OPTICAL PICK-UP KSS-213C
1-669-180-11 OP FLEXIBLE BOARD
1-757-156-11 CABLE, FLEXIBLE FLAT (9 CORE)
1-792-047-11 CABLE, FLEXIBLE FLAT (7 CORE)
224
! 251
267
ANT1
! F901
1-757-155-11
A-4672-541-A
1-676-550-11
1-501-452-22
1-532-465-51
WIRE, PARALLEL (FFC) (22 CORE)
KMS-260B (MD) OPTICAL PICK-UP ASSY
FLEXIBLE BOARD
ANTENNA, TELESCOPIC
FUSE,TIME LAG 3.15A/250V
#1
#2
#3
#4
#5
7-621-255-45
7-627-850-79
7-627-852-08
7-627-852-18
7-627-853-28
SCREW +P 2X6
SCREW, PRECISION +P1.4X1.8TYPE3
SCREW, PRECISION +P 1.7X2.5
SCREW, PRECISION +P 1.7X4 TYPE3
SCREW, PRECISION +P 2X3 TYPE3
! F902
LCD1
M103
M601
M602
1-532-503-51
1-476-281-11
X-3378-325-1
X-2626-327-1
X-2646-617-2
#6
#7
#8
#9
#10
7-682-549-04
7-685-132-19
7-685-533-19
7-685-648-14
7-685-647-79
SCREW +B 3X10
SCREW +P 2.6X5 TYPE2 NON-SLIT
SCREW +BTP 2.6X6 TYPE2 N-S
SCREW +BVTP 3X12 TYPE2 N-S
SCREW +BVTP 3X10 TYPE2 N-S
M603
M902
X-3378-325-1
X-2625-769-1
#11
#12
7-685-649-79 SCREW +BVTP 3X14 TYPE2 N-S
7-685-862-09 SCREW +BVTT 2.6X6
(S)
S701
1-692-960-11
! T901
* HR901
1-435-872-11
1-500-518-11
FUSE,TIME LAG 1.6A/250V
INDICATOR UNIT, LIQUID CRYSTAL
MOTOR ASSY, LOADING (INCLUDING GEAR)
MOTOR ASSY, SPINDLE (MB) (SPINDLE)
MOTOR ASSY, SLED (SLED) (ENCLUDING
GEAR)
MOTOR ASSY, LOADING (ENCLUDING GEAR)
GEAR ASSY, MOTOR (MB) (RP) (SLED)
(ENCLUDING GEAR)
SWITCH, PUSH (1 KEY) (CD DOOR OPEN/
CLOSE)
TRANSFORMER, POWER
HEAD, MD OVER LIGHT
A-3258-095-A REMOTE CONTROLLER (RMT-CM30AD)
**************************************************************
**************
HARDWARE LIST
**************
SP101 1-529-846-11 SPEAKER (8cm)(L-CH)
SP102 1-529-847-11 SPEAKER (5.7cm)(L-CH)
SP201 1-529-846-11 SPEAKER (8 cm) (R-CH)
SP202 1-529-847-11 SPEAKER (5.7 cm) (R-CH)
**************************************************************
The components identified by mark 0
or dotted line with mark 0 are critical
for safety.
Replace only with part number specified.
82
ZS-M30
83
ZS-M30
REVISION HISTORY
Clicking the version allows you to jump to the revised page.
Also, clicking the version at the upper right on the revised page allows you to jump to the next revised
page.
84
Ver.
Date
Description of Revision
1.1
2001.04
Australian model added.
1.0
2001.02
New