Download SERVICE MANUAL - MobileRead Projects

SERVICE MANUAL
PRS-950
US Model
Canadian Model
Ver. 1.0 2010.10
Note:
Be sure to keep your PC used for service and
checking of this unit always updated with the
latest version of your anti-virus software.
In case a virus affected unit was found during
service, contact your Service Headquarters.
SPECIFICATIONS
Model name
PRS-950
Power source
Built-in rechargeable battery: 3.7 V DC
AC adapter: 5.0 V DC, 1,500 mA
USB communication: Hi-Speed USB (USB 2.0 compliant)
Battery life (continuous playback)
Maximum Battery: Approx. 20,000 continuous page turns
when reading only *
* Measured using a text based content in ePub format and a
fully charged battery, consecutive page-turns at
approximately one second per page under the
recommended operating temperature. Actual battery life
may vary based on usage patterns and individual device.
User available capacity
Approx. 1.4 GB after initial setting
Depending on size of pre-loaded excerpts, available memory
capacity may vary.
Operating/charging temperature
41°F to 95°F (5°C to 35°C)
Dimensions (w/h/d)
The contents of each book pre-loaded on this product are copyrighted works,
edited with the cooperation of the publisher.
Copyright laws prohibit copying the data of this product or the contents of this
manual (illustrations, related documents, etc.) in whole or in part without the
permission of the copyright holder. Additionally, use of the data of this product or
the contents of this manual is not allowed without Sony’s permission except for
personal use.
Besides personal use, it is against the copyright law to use any audio or picture
you recorded without prior consent of the copyright holder. Accordingly,
Memory Stick™ media with content protected image or data can be only used
within the law.
Sony, the Sony logo, “BBeB”, “Reader”, “Reader Daily Edition” and their logos are
either trademarks or registered trademarks of Sony Corporation.
, “Memory Stick”, “Memory Stick PRO Duo”, “Memory Stick PRO-HG
Duo”, “Memory Stick Duo”, “Memory Stick Micro”, “M2”, “MagicGate” and their logos
are trademarks of Sony Corporation.
Bitstream is a registered trademark, and Dutch, Font Fusion, and Swiss are
trademarks, of Bitstream Inc.
Microsoft, Windows, Windows Vista and Windows Media are trademarks or
registered trademarks of Microsoft Corporation in the United States and / or other
countries.
Macintosh and Mac OS are trademarks of Apple Inc., registered in the U.S. and
other countries.
This PRS-950 contains Adobe® Reader® Mobile software under license from Adobe
Systems Incorporated, Copyright © 1995-2009 Adobe Systems Incorporated. All
rights reserved. Adobe and Reader are trademarks of Adobe Systems Incorporated.
MPEG Layer-3 audio coding technology and patents licensed from Fraunhofer IIS
and Thomson.
This product includes software developed by the OpenSSL Project for use in the
OpenSSL Toolkit. (http://www.openssl.org/) Copyright© 1998-2008 The OpenSSL
Project. All rights reserved. This product includes cryptographic software written
by Eric Young ([email protected]). This product includes software written by Tim
Hudson ([email protected]). For details on OpenSSL License, refer to “END USER
LICENSE AGREEMENT” in [About] at [Settings] menu on the Reader.
Wi-Fi, the Wi-Fi CERTIFIED logo, WPA, WPA2 and Wi-Fi Protected Setup are
trademarks or registered trademarks of Wi-Fi Alliance.
The Wireless LAN functionality, has passed Wi-Fi certification and complies with the
interoperability specifications established by WFA (Wi-Fi Alliance).
Approx. 5 1/8 × 7 7/8 × 13/32 inches (128 × 200 × 9.6 mm)
Mass
Approx. 9 6/10 oz. (273 g)
Display:
7.1” (180.98 mm) diagonal electrophoretic display
600 × 1,024 pixel, 0.151 × 0.153 pixel/mm
16-level gray scale
Mobile network:
HSPA/WCDMA
GPRS/EDGE
All other system names and product names appearing in this document are the
registered trademarks or trademarks of their respective owners. Further, the
trademark ™ and registered trademark ® symbols are not indicated throughout this
document.
Program ©2010 Sony Corporation
Documentation ©2010 Sony Corporation
850/900/1900/2100 MHz
850/900/1800/1900 MHz
Wi-Fi:
802.11b / g compliant
Expansion slots
Memory Stick PRO Duo™ slot, SD card slot
AC Adapter for Reader (PRSA-AC1)
Output: 5.0 V DC, 1,500 mA
Input: 100 - 240 V AC, 50/60 Hz, 0.2 A
Operating/Charging temperature: 41˚F to 95˚F (5˚C to
35˚C)
Dimensions (w/h/d):
Approx. 1 7/16 × 2 7/8 × 1 5/16 inches (Approx. 36 × 70 ×
33 mm)
Mass: Approx. 1.76 oz. (50 g)
USB cable length: Approx. 58 1/8 inches (1.5 m)
Design and specifications are subject to change
without notice.
9-893-000-01
2010J05-1
© 2010.10
Sony Corporation
Published by Sony Techno Create Corporation
DIGITAL BOOK READER
PRS-950
FLEXIBLE CIRCUIT BOARD REPAIRING
• Keep the temperature of soldering iron around 270 °C during
repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
SAFETY-RELATED COMPONENT WARNING!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR
LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES
PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE
PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS
PUBLIÉS PAR SONY.
2
TABLE OF CONTENTS
1.
SERVICING NOTES .............................................
3
2.
DISASSEMBLY
2-1.
2-2.
2-3.
2-4.
2-5.
2-6.
2-7.
2-8.
2-9.
2-10.
2-11.
2-12.
Disassembly Flow ........................................................... 4
Cover Antenna ................................................................ 4
Panel Rear Block ............................................................ 5
Battery Block Assy (BAT1) ............................................ 5
HP Board ......................................................................... 6
Ornament (B) (Assy) ...................................................... 6
Ornament (T) Assy.......................................................... 7
LED Board ...................................................................... 7
Card Assy (Fox Miniature) (WW1) ................................ 8
WWAN Antenna (ANT1) ............................................... 8
MAIN Board ................................................................... 9
Main Block Assy ............................................................. 10
3.
TEST MODE ............................................................ 11
4.
EXPLODED VIEWS
4-1.
4-2.
4-3.
4-4.
Rear Panel Section ..........................................................
Ornament Section ...........................................................
Main Section ...................................................................
Front Panel Section .........................................................
5.
ACCESSORIES ....................................................... 19
15
16
17
18
PRS-950
SECTION 1
SERVICING NOTES
NOTE THE EACH BOARDS REPAIRING
The mount parts on each boards installed in this set cannot exchange with single. When the each boards are damaged, exchange
the entire mounted board.
NOTE OF REPLACING THE COMPLETE MAIN BOARD
OR MAIN BLOCK ASSY
Please do the following work when you exchange COMPLETE
MAIN board or MAIN BLOCK ASSY.
• How to change the LUT
1. Confirm the lot number of INK INDICATOR 7inch ELEMENT referring to the figure below.
Note: The lot number disappears when the MAIN board is assembled.
Record the lot number in the memo etc. before assembling the
MAIN board.
MAIN BLOCK ASSY
Note: INK INDICATOR 7inch ELEMENT is included in MAIN BLOCK
ASSY.
•
•
Write VCOM: Refer to “20. Write VCOM” on page 14.
REWRITING THE LUT: Refer to this page.
REWRITING THE LUT
As for INK INDICATOR 7inch ELEMENT, the parameter that rewrites the screen of each lot number is different. This parameter is
called LUT (Look Up Table).
When replacing the complete MAIN board or MAIN BLOCK
ASSY (including INK INDICATOR 7inch ELEMENT) you need
to rewrite the LUT.
However, rewriting is not required if the lot number is the same.
Note: LUT is written in IC2003 on the MAIN board.
Refer to the following for the “How to enter the test mode” and
“How to change the LUT”.
• How to enter the test mode
1. Connect the set to PC by the USB cable.
2. The file for the test mode is copied under the “READER”
drive.
Note: Confirm the method of obtaining the file for test mode to each service headquarters.
3. Remove the set from PC. Then, the power supply automatically becomes on.
4. Confirm “Test Mode Available” is displayed on the screen.
-1.68 E505
lot number
2. Confirm the version and the LUT file of LUT corresponding to
the lot number to each service headquarters.
3. Make the following folder under the “READER” drive.
/Sony Reader/software/data
4. Copy the LUT file updated under the folder made in step 3, and
change the file name to “lut.bin”.
5. The current LUT version displayed at the lower side of “Update Waveform” on test mode menu 1
(Example: “000003020605000218031B321B00” in the figure
below).
(Example of displaying current LUT version)
5. Press the key as following order.
[ ]→[ ]→[ ]→[ ]
6. After a while, indicate the test mode menu, enter the test mode.
• Releasing the test mode
Slide the [POWER] key for 5 seconds or more to turn the power
off. Then, delete the file copied in “How to enter the test mode”
from the “READER” drive.
6. Touch the “Update Waveform” in the test mode menu page 1,
it starts rewriting LUT version.
7. After about 10 seconds, screen changes into all white.
8. Press [RESET] key and reboot the set.
9. Enter the test mode again, and confirm LUT version has been
updated.
Wi-Fi OPERATION CHECK
• MAIN board is replaced.
• WWAN ANTENNA is replaced.
• Cable of WWAN ANTENNA is removed.
In the above-mentioned case, confirm the Wi-Fi operation referring to the following.
Procedure:
1. Slide the [WIRELESS] switch to ON.
2. Touch in order of “Settings” → “Wi-Fi Network Settings” →
“Refresh Network List”.
3. Confirm the Wi-Fi access point is displayed.
3
PRS-950
SECTION 2
DISASSEMBLY
•
This set can be disassembled in the order shown below.
2-1.
DISASSEMBLY FLOW
SET
Note 1: Please detach STYLUS, SIM CARD SLOT LID and two DUMMY CARDS beforehand.
Note 2: Please take care not to lose STYLUS, SIM CARD SLOT LID and two DUMMY CARDS.
2-2. COVER ANTENNA
(Page 4)
2-3. PANEL REAR BLOCK
(Page 5)
2-4. BATTERY BLOCK
ASSY (BAT1)
(Page 5)
2-5. HP BOARD
(Page 6)
2-7. ORNAMENT
(T) ASSY
(Page 7)
2-8. LED BOARD
(Page 7)
2-9. CARD ASSY
(FOX MINIATURE)
(WW1)
(Page 8)
2-6. ORNAMENT (B)
(ASSY)
(Page 6)
Note 3: If all items in the dotted line are not removed, the
work doesn't advance to "2-11. MAIN BOARD".
2-11. MAIN BOARD
(Page 9)
2-10. WWAN ANTENNA
(ANT1)
(Page 8)
2-12. MAIN BLOCK ASSY
(Page 10)
Note: Follow the disassembly procedure in the numerical order given.
2-2.
COVER ANTENNA
2 two tapping screws
1 tapping screw
(P2)
3 claw
5 seven claws
4
6 cover antenna
– Rear side view (bottom side) –
4
PRS-950
2-3.
PANEL REAR BLOCK
Note: IWhen installing the sheet (cable),
please paste it referring to the following.
3 four claws
6 panel rear block
2 two tapping screws
claw
3 three claws
7 to 10 mm
sheet (cable)
3 four claws
4
5 two sheets (cable)
claw
15 to 18 mm
sheet (cable)
1 tapping screw
(P2)
– Panel rear inner view –
2-4.
– Rear side view (bottom side) –
BATTERY BLOCK ASSY (BAT1)
Note 1: When installing the copper foil (IC), please paste it
so as not to protrude beyond the sheet (battery).
2 sheet (cable)
9 battery block assy (BAT1)
sheet (battery)
copper foil (IC)
4 copper foil (IC)
1 cushion (stylus)
MAIN board
IC
3 battery connector
6 Pull the sheet (battery) and lift the battery block.
5 Peel the sheet (battery).
7
8 sheet (battery)
Note 3: Peel off so as not to
damage the battery
block assy (BAT1).
‡:LUHSURFHVVLQJ
Note 2: Please process it so that battery wire
should not run aground in chassis and
module connector.
chassis
module connector
–5HDUVLGHYLHZERWWRPVLGH–
sheet (cable)
battery wire
MAIN board
5
PRS-950
2-5.
HP BOARD
2 two shafts
(M1.4 u 2.5)
4 HP board
1 HP flexible board
3
– Rear side view (bottom side) –
2-6.
ORNAMENT (B) (ASSY)
1 shaft
(M1.4 u 1.8)
2 three tapping screws
3 claw
2 two tapping screws
7 key reset
Note 2: When installing three tapping
screws, please tighten after drawing
the ornamennt (B) (assy) to the main
block.
2 main block
8 ornament (B)
(assy)
2
2
1 push
5 rib
1 push
6
1 push
ornament (B) (assy)
Note 1: When installing the ornament (B) (assy)
block, the position of switch and knob
(wireless) is set and installed.
switch
4 two adhesive sheets
(ornament)
knob (wireless)
– Rear side view (bottom side) –
6
PRS-950
2-7.
ORNAMENT (T) ASSY
5 ornament (T) assy
Note 2: When installing ornament (T) assy,
please match the position of three
bosses and three holes respectively.
Note 1: When installing the ornament (T) assy,
the position of switch and knob power
is set and installed.
4 three tapping screws
hole
Note 3: When installing three tapping
screws, please tighten after drawing
the ornamennt (T) assy to the main
block.
2
ornament (T) assy 1 push
1 push
2
knob power
2 screw
1 light guide
MSSD
two holes
3 light guide
power
boss
switch
two bosses
2
1 push
main block
– Rear side view (bottom side) –
2-8.
LED BOARD
Note 2: When installing four shafts, please
tighten in following numerical order.
Note 3: Please tighten while suppressing the
LED board so that it should not bend.
4
1 four shafts
(M1.4 u 2.5)
2 shaft
(M1.4 u 1.8)
hole
hole
5 LED board
Note 1: When installing LED board,
please match the position of
three bosses and three holes
respectively.
hole
3
3
2
boss
LED board
1
boss
boss
4 FL5033 flexible board
(FPC1)
– Rear side view (bottom side) –
7
PRS-950
2-9.
CARD ASSY (FOX MINIATURE) (WW1)
Note: When the WWAN antenna cable is removed, refer to “Wi-Fi OPERATION CHECK” (page 3).
1 two new truster screws
(M2)
4 card assy (fox miniature)
(WW1)
2
3 WWAN antenna cable
– Rear side view (bottom side) –
2-10. WWAN ANTENNA (ANT1)
Note 1: When the WWAN antenna is removed, refer to “Wi-Fi OPERATION CHECK” (page 3).
‡ :ire SroFessiQJ
1 sheet (antenna)
Note 3: When pasting sheet (antenna), please let me
stick to MAIN board rubbing on several times.
WWAN antenna cable
Note 2: Please take care not to run aground in the chassis.
chassis
sheet (antenna) WWAN antenna
4 Peel the adhesive.
5 WWAN antenna
(ANT1)
3 Peel the aluminum tape.
Note 4: When pasting aluminum
tape, please let me stick to
MAIN board rubbing on
several times.
mounted parts
MAIN board
1 + 1 (-0) mm
mounted parts
1 + 1 (-0) mm
3 Peel the aluminum tape.
Note 4: When pasting aluminum tape, please let me
stick to MAIN board rubbing on several times.
2 WWAN antenna cable
8
– Rear side view (bottom side) –
PRS-950
2-11. MAIN BOARD
Note 1: When the MAIN board is removed, refer to “Wi-Fi OPERATION CHECK” (page 3).
‡ :ire SroFessiQJ
WWAN antenna cable
Note 2: Please take care not to run aground in the chassis.
2 sheet (antenna)
Note 3: When pasting sheet (antenna), please let me
stick to MAIN board rubbing on several times.
chassis
sheet (antenna) WWAN antenna
5 Peel the aluminum tape.
Note 4: When pasting aluminum
tape, please let me stick to
MAIN board rubbing on
several times.
3
mounted parts
MAIN board
1 + 1 (-0) mm
mounted parts
1 + 1 (-0) mm
4 WWAN antenna cable
5 Peel the aluminum tape.
Note 4: When pasteing aluminum tape, please let me
stick to MAIN board rubbing on several times.
1 ink indicator element
flexible board
– Rear side view (bottom side) –
Note 5: Please note the direction when you
install FL5033 flexible board (FPC1).
to LED board
9 FL5033 flexible board (FPC1)
6 twelve shafts
(M1.4 u 1.8)
7 two tapping screws
FL5033 flexible
board (FPC1)
to MAIN board
8
0 MAIN board
9
PRS-950
2-12. MAIN BLOCK ASSY
1 two magnet 6x7 blocks
hole
2 five screws
two holes
3 main block assy
Note 1: When installing main block assy,
please match the position of five
bosses and five holes respectively.
hole
boss
hole
two bosses
boss
boss
– Rear side view (bottom side) –
Note 2: When installing the magnet 6x7 block, note the position of
sheet (magnet) of the magnet 6x7 block.
magnet 6x7 sheet (magnet)
magnet 6x7
sheet (magnet) side
sheet (magnet)
sheet (magnet) side
10
PRS-950
SECTION 3
TEST MODE
HOW TO ENTER THE TEST MODE
1. Connect the set to PC by the USB cable.
2. The file for the test mode is copied under the “READER”
drive.
Note: Confirm the method of obtaining the file for test mode to each service headquarters.
3. Remove the set from PC. Then, the power supply automatically becomes on.
4. Confirm “Test Mode Available” is displayed on the screen.
5. Press the key as following order.
[ ]→[ ]→[ ]→[ ]
6. After a while, indicate the test mode menu, enter the test mode.
7. Press the [<]/[>] keys, change the test mode menu page 1/page
2.
OPERATION OF THE TEST MODE
1. Test Panel
Procedure:
1. Make the following folder under the “READER” drive.
/Sony Reader/software/images
2. Copy the image files under the folder made in step 1.
3. Touch the “Test Panel” in the test mode menu page 1.
The screen is changed into the image files.
4. Press the [<]/[>] keys, change the image files.
5. Press the [ ] key, image file display size change to 600×800 or
500×700.
6. If there are no image files, screen is filled with grayscale color.
Press the [<]/[>] keys, change the grayscale color.
>
WHITE
<
>
LIGHT GRAY
<
>
DARK GRAY
<
>
BLACK
<
When the setting of “17. Slideshow Setting” is turning on, the
image files (or grayscale color) are changes by the automatic
operation.
Releasing method:
Press the [ ] key, return to the test mode menu 1.
2. Drawing with point
Procedure:
1. Touch the “Drawing with point” in the test mode menu page 1.
The screen is changed into the drawing check.
2. The scanned coordinate is displayed while dragging.
(Test mode menu page 1)
(Test mode menu page 2)
RELEASING THE TEST MODE
Slide the [POWER] key for 5 seconds or more to turn the power
off. Then, delete the file copied in “How to enter the test mode”
from the “READER” drive.
(Screen display)
Releasing method:
Press the [ ] key, return to the test mode menu 1.
11
PRS-950
3. Test TP Coordinate
Procedure:
1. Touch the “Test TP Coordinate” in the test mode menu page 1.
The screen is changed into the touch panel coordinate.
2. The scanned coordinate is displayed pen down and pen up.
The grid is drawn every 100 pixels.
All the touch panel data is recorded in the log file.
(pen down, pen move, pen up, pressure)
screen coordinate
5. Check battery
Touch the “Check battery” in the test mode menu page 1.
Display of the right side of “Check battery” on test mode menu
changes into the display of the battery level.
6. Factory Initialize
Touch the “Factory Initialize” in the test mode menu page 1.
Clean up all the evidence and reset all settings, then shutdown.
7. Version confirmation
Procedure:
1. Touch the “Version confirmation” in the test mode menu page
1.
2. Each version of this set are displayed.
Note: “Preload contents version” is not displayed.
raw coordinate
pressure
Note: The value displayed
in "pressure" is invalid
because of the optical
touch panel.
Firmware version: 1.0.00.08100
Preload contents version:
Preload Partition version: 1.0.00.08100
(Screen display)
eDictionary contents version: 1.0.00.07150
Releasing method:
Press the [ ] key, return to the test mode menu 1.
Installer Launcher version: 1.0.00.08100
4. Test All Keys
Procedure:
1. Touch the “Test All Keys” in the test mode menu page 1.
The screen is changed into the all keys state.
(Screen display)
Releasing method:
Press the [ ] key, return to the test mode menu 1.
HOME
PREV
NEXT
SIZE
OPTION
VOL+
VOL-
(Screen display)
2. Each keys are pressed, the display changed from white into the
black.
3. It returns to the test mode menu 1 when all buttons are pressed.
Releasing method:
Press the [OPTION] key for 3 seconds or more, return to the test
mode menu 1.
12
PRS-950
8. Update Waveform
In this mode, it is possible to confirm the variation of LUT and
rewrite.
As for INK INDICATOR 7inch ELEMENT, the parameter that rewrites the screen of each lot number is different. This parameter is
called LUT (Look Up Table).
When replacing the complete MAIN board or MAIN BLOCK
ASSY (including INK INDICATOR 7inch ELEMENT) you need
to rewrite the LUT.
However, rewriting is not required if the lot number is the same.
Note: LUT is written in IC2003 on the MAIN board.
Procedure:
1. Confirm the lot number of INK INDICATOR 7inch ELEMENT referring to the figure below.
Note: The lot number disappears when the MAIN board is assembled.
Record the lot number in the memo etc. before assembling the
MAIN board.
MAIN BLOCK ASSY
10. Power Off
Touch the “Power Off” in the test mode menu page 1.
After a while, the screen display is changed white, so power is
turned off.
11. Log Extract
Touch the “Log Extract” in the test mode menu page 1.
The device saves the log files of using right now.
12. NAND Log Extract
Touch the “NAND Log Extract” in the test mode menu page 1.
The device saves the log files of using last time before rebooted
or shutdown.
13. Self Log Extract
It is the tool for the developer.
This mode is not used in servicing.
14. Log Convert
It is the tool for the developer.
This mode is not used in servicing.
15. Calibration
Note: The calibration need not be executed in this set. There is a possibility that the problem occurs in this set when this item is executed. Never execute this item.
-1.68 E505
lot number
2. Confirm the version and the LUT file of LUT corresponding to
the lot number to each service headquarters.
3. Make the following folder under the “READER” drive.
/Sony Reader/software/data
4. Copy the LUT file updated under the folder made in step 3, and
change the file name to “lut.bin”.
5. The current LUT version displayed at the lower side of “Update Waveform” on test mode menu 1
(Example: “000003020605000218031B321B00” in the figure
below).
16. Check Temperature
Touch the “Check Temperature” in the test mode menu page 2.
Display of the right side of “Check Temperature” on test mode
menu changes into the display of the temperature.
17. Slideshow Setting
Touch the “Slideshow Setting” in the test mode menu page 2, slideshow on/off changes whenever it touch the “Slideshow Setting”.
The setting is on, next image is shown every 3 seconds.
18. Test Audio
Procedure:
1. Make the following folder under the “READER” drive.
/Sony Reader/software/audio
2. Copy the audio files under the folder made in step 1.
3. Touch the “Test Audio” in the test mode menu page 2.
The screen is changed into the audio check.
4. Press the [<]/[>] keys, change the audio files.
5. Press the [OPTIONS] key, music play or pause.
6. Press the [VOL +]/[VOL –] keys, volume level up or down.
(Example of displaying current LUT version)
6. Touch the “Update Waveform” in the test mode menu page 1,
it starts rewriting LUT version.
7. After about 10 seconds, screen changes into all white.
8. Press [RESET] key and reboot the set.
9. Enter the test mode again, and confirm LUT version has been
updated.
Releasing method:
Press the [ ] key, return to the test mode menu 2.
Even if you return to test mode menu, music is still playing. You
can “Test Audio” and other things at the same time.
9. Reset Device Lock
The current state of device lock and the password are displayed on
the right side of “Reset Device Lock” of test mode menu page 1.
Touch the “Reset Device Lock” to reset the device lock.
13
PRS-950
19. Test Battery Life
Procedure:
1. Make the following folder under the “READER” drive.
/Sony Reader/software/books
2. Copy the book contents file supported in this set (ePub, PDF,
text, RTF, BBeB) under the folder made in step 1.
3. Touch the “Test Battry Life” in the test mode menu page 2.
1 seconds
ONE
ALL
20. Write VCOM
In this mode, the VCOM voltage can be rewritten.
The VCOM voltage for INK INDICATOR 7inch ELEMENT varies for each INK INDICATOR 7inch ELEMENT.
When replacing the complete MAIN board or MAIN BLOCK
ASSY (including INK INDICATOR 7inch ELEMENT) you need
to rewrite the VCOM voltage.
Procedure:
1. Confirm the VCOM voltage for INK INDICATOR 7inch (L)
ELEMENT referring to the figure below.
Note: The VCOM voltage disappears when the MAIN board is assembled.
Record the VCOM voltage in the memo etc. before assembling the
MAIN board.
MAIN BLOCK ASSY
-1.68 E505
VCOM voltage
(Screen display)
4. Touch the “ONE” or “ALL”, and the page is turned until the
battery runs down.
Note: The battery have run out if this mode is executed. Release this mode
by pressing the [ ] key when you want to stop it on the way.
ONE:
ALL:
Page of one book in the copied books is turned.
Page of all book in the copied books is turned.
2. Make the text file, and write the VCOM voltage confirmed in
step 1. The VCOM voltage is described by the unit of mV that
omits minus (Write “1680” when it is printed on the label as
“–1.68 V”). Then, change the file name to “Vcom.dt”.
3. Make the following folder under the “READER” drive.
/Sony Reader/software/data
4. Copy the file made in step 2 under the folder made in step 3.
5. The current VCOM voltage displayed at the lower side of
“Write VCOM” on test mode menu 2 (Example: “–1.650 V” in
the figure below).
5. Whenever 100 pages are turned, the result is maintained in the
following file.
/Sony Reader/software/books/counter
Releasing method:
Press the [ ] key, return to the test mode menu 2.
(Example of displaying current VCOM voltage)
6. Touch the “Write VCOM” in the test mode menu page 2, it
starts rewriting the VCOM voltage.
7. Confirm the VCOM voltage has been updated.
14
PRS-950
SECTION 4
EXPLODED VIEWS
Note:
• -XX and -X mean standardized parts, so
they may have some difference from the
original one.
• Items marked “*” are not stocked since
they are seldom required for routine service. Some delay should be anticipated
when ordering these items.
4-1.
• The mechanical parts with no reference
number in the exploded views are not supplied.
• Color Indication of Appearance Parts Example:
KNOB, BALANCE (WHITE) . . . (RED)
↑
↑
Parts Color Cabinet’s Color
REAR PANEL SECTION
• Rear side view
5
7
8
6
SIM1
4
ornament section
9
1
3
4
not supplied
2
2
Ref. No.
Part No.
Description
1
2
3
4
5
4-196-615-11
3-078-890-11
4-196-616-11
3-080-204-11
A-1794-926-A
PANEL REAR
SCREW, TAPPING
COVER ANTENNA
SCREW, TAPPING, P2
STYLUS BLOCK ASSY (Stylus)
6
A-1794-930-A
LID (CARD) BLOCK ASSY
Remark
Ref. No.
Part No.
Description
Remark
7
8
4-198-978-01
4-198-979-01
9
SIM1
4-156-278-01
X-2560-950-1
CARD (SD), DUMMY (for SD card slot)
CARD (MS), DUMMY
(for Memory Stick PRO DuoTM slot)
SHEET (CABLE)
CARD ASSY, SIM (for SERVICE)
15
PRS-950
4-2.
ORNAMENT SECTION
• Rear side view
64
55
63
65
61
60
56
54
51
62
55
main section
53
61
60
52
59
57
58
BAT1
66
55
51
Ref. No.
Part No.
Description
51
52
53
54
55
4-259-711-01
4-259-712-01
4-199-844-01
X-2560-971-1
3-078-890-11
CUSHION (STYLUS)
COPPER FOIL (IC)
SHEET (BATTERY)
ORNAMENT (B) (ASSY)
SCREW, TAPPING
56
57
58
59
4-262-516-11
4-196-613-01
4-262-517-01
A-1792-541-A
SHAFT M1.4X1.8 (H=0.2)
KEY RESET
SHAFT M1.4X2.5 (B TITE)
HP BOARD, COMPLETE
16
Remark
Ref. No.
Part No.
Description
60
4-155-226-01
SHEET (MAGNET)
61
62
63
64
65
4-196-614-01
4-196-610-01
4-198-971-01
X-2560-970-1
4-196-609-01
MAGNET 6X7
LIGHT GUIDE POWER
SHEET (ORNAMENT), ADHESIVE
ORNAMENT (T) ASSY
LIGHT GUIDE MSSD
66
BAT1
4-156-278-01
A-1792-542-A
SHEET (CABLE)
BATTERY BLOCK ASSY
Remark
PRS-950
4-3.
MAIN SECTION
• Rear side view
front panel section
107
105
106
102
103
104
FPC1
102
108
103
WW1
ANT1
102
101
Note: When the MAIN board or WWAN antenna is removed,
refer to “Wi-Fi OPERATION CHECK” (page 3).
Ref. No.
Part No.
Description
Remark
101
102
103
104
105
2-630-005-21
4-262-516-11
3-078-890-11
A-1792-764-A
4-262-517-01
SCREW (M2), NEW TRUSTER, P2
SHAFT M1.4X1.8 (H=0.2)
SCREW, TAPPING
LED BOARD, COMPLETE
SHAFT M1.4X2.5 (B TITE)
106
107
X-2560-948-1
A-1792-537-A
MAIN BOARD, COMPLETE (for SERVICE)
MAIN BLOCK ASSY
(Including INK INDICATOR 7inch ELEMENT)
Ref. No.
Part No.
Description
Remark
108
ANT1
FPC1
4-199-845-01
1-754-728-11
1-882-791-11
SHEET (ANTENNA)
ANTENNA, WWAN
FL5033 FLEXIBLE BOARD
WW1
X-2560-949-1
CARD ASSY, (FOX MINIATURE) (Gobi 2000)
(for SERVICE)
17
PRS-950
4-4.
FRONT PANEL SECTION
• Rear side view
159
157
156
158
155
154
153
152
151
Note: KEY TOP (Ref. No. 153) included each button by two pairs.
Ref. No.
151
152
153
154
155
18
Part No.
Description
4-196-604-01
4-196-603-01
4-196-597-11
4-155-094-01
4-155-095-01
LIGHT GUIDE
HINJI KEY
KEY TOP (1 set)
CUSHION TP (UPPER)
CUSHION TP (SIDE)
Remark
Ref. No.
156
157
158
159
Part No.
Description
3-078-890-11
4-196-605-01
4-259-710-01
4-196-596-11
SCREW, TAPPING
GUIDE STYLUS
GASKET (FRONT)
PANEL FRONT
Remark
PRS-950
SECTION 5
ACCESSORIES
Ref. No.
0
Part No.
Description
1-489-298-12
1-838-503-21
4-257-320-11
X-2560-950-1
AC ADAPTOR (PRSA-AC1)
CABLE, USB (MICRO B) (USB cable)
QUICK START GUIDE (ENGLISH)
CARD ASSY, SIM (for SERVICE)
Remark
The components identified by mark 0
or dotted line with mark 0 are critical for
safety.
Replace only with part number specified.
Les composants identifiés par une marque
0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant le numéro spécifié.
19
PRS-950
REVISION HISTORY
Checking the version allows you to jump to the revised page.
Also, clicking the version at the top of the revised page allows you to jump to the next revised page.
Ver.
Date
1.0
2010.10
Description of Revision
New