Download INSTRUCTION MANUAL
Transcript
INSTRUCTION MANUA L Manuel d'utilisation C SkyRC Technology Co., Ltd. 2010 Version 1.0 Sauf erreurs et omissions, sous réserve de modifications. Attention cette traduction de la notice du charger e6650 est la propriété de la société Beez2B. Toute reproduction même partielle est interdite. Copyright © 2011 Beez2B TABLE MATIERES TABLEDES OF CONTENTS TABLEde OFmatières CONTENTS Table Introduction INTRODUCTION INTRODUCTION Special FeaturesSPECIFIQUES CARACTERISTIQUES Lithium Polymer Balance Charge Program Connection EX. DE CONNECTION POUR CHARGER/EQUILIBRER UNE BATTERIEDiagram LIPO WarningD’AVERTISSEMENT and Safety Notes NOTICES ET DE SECURITE Program Flow Chart ORGANIGRAMME DU PROGRAMME Initial SETUP(REGLAGE Parameter Setup (Users Set Up) MENU UTILISATEUR) Lithium (LiPo/Lilon/LiFe) program PROGRAMME LITHIUM (LiPo/LiIon/LiFe) ChargingUNE Lithium Battery in Charge Mode CHARGER BATTERIE LITHIUM EN MODE CHARGE ChargingUNE Lithium Battery in Balance Mode CHARGER BATTERIE LITHIUM EN MODE BALANCE Fast Charging of Lithium Battery CHARGE RAPIDE D’UNE BATTERIE LITHIUM Charging Lithium Battery in the Fast Charge Mode CHARGE RAPIDE D’UNE BATTERIE LITHIUM MODE ENTRETIEN BATTERIE LITHIUM Storage ControlPOUR of Lithium Battery CHARGER L’ ENTRETIEN D’UNE BATTERIEMode LITHIUM ChargingPOUR Lithium Battery in the Storage Discharging of BATTERIE Lithium Battery DECHARGER UNE LITHIUM Voltage Balancing andET Monitoring in the Discharge Process EQUILIBREUR DE TENSION SURVEILLANCE PENDANT LA DECHARGE ChargingUNE of NiCd/NiMH Battery CHARGER BATTERIE NICD/NIMH ChargingUNE NiCd/NiMH Battery in the Mode CHARGER BATTERIE LNICD/NIMH ENCharge MODE CHARGE Discharge UNE of NiCd/NiMH Battery DECHARGER BATTERIE NICD/NIMH Charge/Discharge and Discharge/Charge Cycle of NiCd/NiMH Battery CYCLE DE CHARGE / DECHARGE D’UNE BATTERIE NICD/NIMH ChargingUNE of the Pb Battery CHARGER BATTERIE Pb ChargingUNE PbBATTERIE (lead-acid) Battery the Charge Mode CHARGER Pb EN MODEinCHARGE Discharging of BATTERIE the Pb Battery DECHARGER UNE Pb Data Storage PROGRAMME DEProgram SAUVEGARDE DES DONNEES Load Data Program CHARGER LE PROGRAMME DE DONNEES Various Information in theDURANT Program DIFFERENTES INFORMATIONS LA CHARGE / DECHARGE Warning and ErrorET Message MESSAGES D’ERREUR DE SECURITE Specifications SPECIFICATIONS Warranty and Service GARANTIE 02 03 05 06 11 12 15 16 16 17 17 18 18 19 19 20 20 20 21 21 22 22 23 24 25 26 27 27 - 01 - Sauf erreurs et omissions, sous réserve de modifications. Attention cette traduction de la notice du charger e6650 est la propriété de la société Beez2B. Toute reproduction même partielle est interdite. Copyright © 2011 Beez2B INTRODUCTION INTRODUCTION Introduction Thank you for purchasing e6650 LiPo Balance Charger by de Nous vous remercions d’avoir the acheter un e6650 LiPo Balancing charger SKYRC.This product a rapidrapide charger a high performance SKYRC. Ce produit est un is chargeur avecwith un micro-processeur de microprocessor specialized read haute performanceand et un logiciel trèsoperating spécialisé. software. Veuillez lirePlease attentivethis entire operating manual completely attentively ment le manuel d’instructions avant d’utiliserand ce produit, car il before contient using this product, as it coversbien a wide range et of des information on de une large variété de programmes spécifiques informations operating and safety or please do use this product in company sécurité. with a specialist! LCD Display (16 chr.* 2 lines) Entrée source DC Port DC Input Power 11-18V DC Entrée source AC Port AC Input Power (AC 100-240V, 50/60HZ) Temperature Température entrée sensor Sensor Port Temperature Controlled Fan Parcourir le ménu principal. Balance Arrête n’importe Sortie pour Scroll Through Socket quelthe procès charl’équilibrage MaindeMenu ge Stop any Charge Processes Outputde charge Sortie Alter Values Cells Valeurs Charging in Balance Charge Mode Montre l’état individuelle des See the Status of Individual cellules en équilibrage Résumer ou démarrer le procès de charge. Resume or Start Charge Processes Confirmation Confirm an Action - 02 - Sauf erreurs et omissions, sous réserve de modifications. Attention cette traduction de la notice du charger e6650 est la propriété de la société Beez2B. Toute reproduction même partielle est interdite. Copyright © 2011 Beez2B CARACTERISTIQUES SPECIFIQUES SPECIAL FEATURES SPECIAL FEATURES Caractéristiques spécifiques Optimized operating software Logiciel de gestion très élaboré e6650 featuresune thedétection so-calledautomatique AUTO function thatle set the feeding Le e6650 détermine qui gère courant pendant la current during the process of pour charging or discharging. Especially charge et la décharge. Spécialement les accus Lithium, le chargeur évitera for Lithium batteries, overcharging may la surcharge, pouvant meneritàcan uneprevent batterie the défectueuse. Si unewhich mauvaise lead to an to the user's fault. Itsonne can disconnect the manipulation deexplosion l’utilisateurdue est détectée, une alarme et le chargeur circuit automatically andlealarm detecting malfunction. déconnecte automatiquement circuitonce de charge. Tous any les programmes sont programs of thiset product were controlled through two way gérésAlletthe interactifs contrôlant détectant toutes les erreurs de l’utilisateur. linkage to achieve the safety and L’appareil estand municommunication, d’un port de communication pourmaximum d’éventuelles mises à the trouble. All the settings can be configured by users! jour minimize dans le futur. Internaldeindependent lithium battery balancer Equilibreur tension intégré pour batteries Lithium e6650 employs an individual-cell-voltage balancer. It isn‟t Le chargeur e6650 possède un équilibreur de tension intégré pour chaque necessary to connect an external balancerséparé for balance élément individuel. Il ne nécessite pas d’équilibreur pour lacharging. charge des batteries Lithium. Balancing individual cells battery discharging During the process of discharging, e6650 can monitor and Equilibrage éléments pendant la décharge balancedes each cell ofindividuels the battery individually. Error message will Le e6650 contrôle également l’équilibrage desended éléments Lithium pendant be indicated and the process will be automatically if thele mode décharge. Si lasingle tensionone d’uncell élément varie anormalement le mode de voltage of any is abnormal. décharge sera interrompu et le message « error » apparaîtra. Adaptable to various type of lithium battery Convient pour les différents de types batteries Lithium batteries, such as e6650 is adaptable to types various of Lithium Le chargeur e6650and peutthe charger les 3 types Lithium : Li-ion, LiPo et Li-ion, LiPo new LiFe seriesdeofbatteries batteries. LiFe. Fast and storage mode of lithium battery Purposes charge Lithium varies, „fast‟ charge reduce Mode de chargetorapide « Fast » ou battery d ‘entretien « Storage » duration of vos charging, „store‟ state can control La thecharVousthe pouvez charger batterieswhereas Lithium de deux façons différentes. final voltage of your battery, as to storeque forleamode long time and ge rapide « Fast » réduit le temps de so charge tandis d’entretien protect useful time of thefinale battery. « Storage » contrôle la tension de la batterie, afin d’entreposer celle-ci dansMaximum les meilleures conditions. safety Delta-peak sensitivity: The automatic charge termination program Sécurité maximale based on the principle of the Delta-peak voltage detection. When Détection par Delta-peak, fin de charge est détectéethe parprocess ce mode.will Quand the battery's voltagelaexceeds the threshold, be le courant de la batterie dépasse le seuil, le processus de charge est arrêté autoterminated automatically. matiquement. - 03 - Sauf erreurs et omissions, sous réserve de modifications. Attention cette traduction de la notice du charger e6650 est la propriété de la société Beez2B. Toute reproduction même partielle est interdite. Copyright © 2011 Beez2B CARACTERISTIQUES SPECIAL FEATURES SPECIFIQUES Automatic charging current Sécurité de charge en mode « Auto limit » You lacan set up the upper limit the en charging when sont Pendant charge de batteries NiCd etof NiMH mode «current Auto », celles-ci charging your NiCd or NiMH it is useful foravec thedes NiMH protégées de courants de charge tropbattery; élevés, spécialement batteries à battery of low impedance and capacity in the 'AUTO' charging faible capacité. mode. Limites de charge Capacity limit La capacité de charge est toujours calculée : le courant charge multiplié par The charging capacity is always calculated asde the charging la durée. Si les limites permises sont dépassées, le procédé interrompu current multiplied by time. If the charging capacitysera exceeds the automatiquement lorsque sélectionnezautomatically les valeurs maximums. limit, the process willvous be terminated when you set the maximum value. Protection thermique lors d’une charge de batterie Temperature threshold* La charge sera interrompu la température la batterie atteint la The battery‟s internallorsque chemical reaction willdecause the temperature limite programmée. Cette fonction estlimit disponible en connectant ofde thedegrés battery to rise. If the temperature is reached, the une module température en option, donc pas incluse. process will be terminated. * This function is available by connecting optional temperature Affichage de la tension d’alimentation probe, which is not included in our package. Afin de protéger la tension de la batterie de voiture, le voltage d’entrée est Processing time affiché. Si la tension estlimit: en dehors des limites, le processus de charge est interYou can also limit the maximum process time to avoid any rompu automatiquement. possible defect. Charge et stockage de données Input power monitoring PourTo votre facilité 5 configurations différentes de batteprotect thevous carpouvez batterystocker used as DC input power from being ries pour voitures, récepteur ou autre. damaged, its avions, voltageémetteur, keeps being monitored. If it drops below the lower limit, the process will be ended automatically. Cycles charge/décharge Data store/load Réanimer vos accus pour l’entretien périodique ou après une longue période The maximum five batteries‟ data can be stored for users‟ de stockage. Le chargeur charge la batterie jusqu’à sa capacité maximale puis la convenience. You can keep the data pertaining to program décharge lentement jusqu’à un niveau sûre et ceci jusqu’à 5 fois. setting of the battery of continuous charging or discharging. Users can call out these data at any time without any special program setting. Cyclic charging/discharging 1 to 5 cyclic and continuous process of charge>discharge or discharge>charge is operable for battery refreshing and Balancing to stimulate the battery's activity. - 04 - Sauf erreurs et omissions, sous réserve de modifications. Attention cette traduction de la notice du charger e6650 est la propriété de la société Beez2B. Toute reproduction même partielle est interdite. Copyright © 2011 Beez2B Exemple de connexion pour charger/ équilibrer une batterie Lithium polymère LITHIUM POLYMER BALANCE CHARGE PROGRAM CONNECTION DIAGRAM Exemple de connexion pour charger/ équilibrer une batteLITHIUM POLYMER BALANCE CHARGE PROGRAM rie Lithium polymère CONNECTION DIAGRAM This diagram shows correctvotre way batterie to connect your battery La bonne méthode pourthe connecter au chargeur e6650to dans e6650 charger while charging in the balance charge program lethe mode balance mode only. AVERTISSEMENT WARNING: Failure to connect asque shown in this diagram will damage this Une connexion autre celle montrée dans la phot peut endommager charger. le chargeur. The main battery leads must be connected along with theêtre balance Les connexions principales et le connecteur de balance doivent raccorlead as shownlabefore dées connector avant de commencer charge.charging your battery . - 05 - Sauf erreurs et omissions, sous réserve de modifications. Attention cette traduction de la notice du charger e6650 est la propriété de la société Beez2B. Toute reproduction même partielle est interdite. Copyright © 2011 Beez2B NOTICES WARNINGD’AVERTISSEMENTS AND SAFETY NOTES ET DE SECURITE WARNING AND SAFETY NOTES Notices d’avertissements et de sécurité These warnings and safety notes are particularly important. Ces notices d’avertissement et de sécurité sont particulièrement importanPleaselesfollow the instructions for maximum safety; otherwise the tes. Suivez instructions pour une sécurité maximale; vos batteries, charand the battery damaged or at si worst it canest cause geurcharger et personnes peuvent subircan desbe endommagements le produit mal a fire. utilisé. Ne laissez jamais votre chargeur non surveillé quand il est connecté à son Never leave the charger unattended when it is connected to its alimentation. Si un défaut est trouvé, coupez le chargeur et consultez le power supply. If any malfunction is found, Terminate THE manuel. PROCESS AT ONCE and refer to the operation manual. Gardez votre chargeur à l’abri de poussière, humidité, pluie, soleil directe et Keep the charger well away from dust, damp, rain, heat, direct vibrations. Ne laissez pas tomber l’appareil. sunshine and vibration. Never drop it. La tension est de 11-18 V en courant continu ou de 100-240 V en Thed’entrée allowable input voltage is 11-18V DC/110-240V AC. courant alternatif. This charger and the battery should be put on a heat-resistant, Pendantnoninflammable son utilisation, placez chargeur à un endroit ininflammable and le nonconductive surface. Never placeetthem non-conductible ne l’utilisez sur un tapis,allsiège voiture ou maon a car et seat, carpet jamais or similar. Keep the de inflammable tières similaires. volatile materials away from operating area. Assurez-vous lesyou spécifications la batterie à charger ou à décharger Makeque sure know the de specifications of the battery to be correspondent aux ce chargeur. Unthe programme de charcharged orcaractéristiques discharged to de ensure it meets requirements of ge inadéquat peut engendrer une explosion de vos batteries, ou elles peuthis charger. If the program is set up incorrectly, the battery vent même garantie ne couvre pas les composants détruits and s’enflammer. charger mayLabe damaged .It can cause fire or explosion lors de l’usage du produit ou les modifications de l’ensemble ainsi que le due to overcharging. This warranty is not valid for any damage détérioration due à l’utilisation de arising colles ouasautres produits non spécifiés or subsequent damage a result of a misuse or failure dans la notice. to observe the procedures outlined in this manual. - 06 - Sauf erreurs et omissions, sous réserve de modifications. Attention cette traduction de la notice du charger e6650 est la propriété de la société Beez2B. Toute reproduction même partielle est interdite. Copyright © 2011 Beez2B NOTICES D’AVERTISSEMENTS ET DE SECURITE WARNING AND SAFETY NOTES NiCd/NiMH NiCd/NiMH - Voltage level: 1.2V/cell Tension par élément : 1,2 V - Allowable fast charge current: (depends on the Courant de charge rapide autorisé : 1-21C-2C C (Dépend de la performanperformance ce des éléments). of cell) - Discharge voltage cut off level: (NiCd),1.0 V/ Voltage de coupure à la décharge : 0.85 0.85V/cell V/élément (NiCd), 1.0V/cell(NiMH) élement (NiMH) Li-ion Li-ion - Voltage level: 3.6V/cell Tension par élément : 3.6 V - Max. voltage: 4.1V/cell Tension decharge charge maximale par élément : 4.1 V - Allowable fast charge current: or less Courant de charge rapide autorisé : 1C 1C ou moins - Min. voltage cut: off 2.5V/cell or higher Voltage dedischarge coupure à la décharge 2.5 level: V/élément ou plus LiPoLiPo - Voltage level: 3.7V/cell Tension par élément : 3.7 V - Max. voltage: 4.2V/cell Tension decharge charge maximale par élément : 4.2 V - Allowable fast charge current: or less Courant de charge rapide autorisé : 1C 1C ou moins - Discharge voltage cut off level: 3.0V/cell ou or plus higher Voltage de coupure à la décharge : 3.0 V/élément LiFeLiFe Tension par élément : 3.3 V - Voltage level: 3.3V/cell Tension decharge charge maximale par élément : 3.6 V - Max. voltage: 3.6V/cell Courant de charge rapide autorisé : 4 C4C ou moins - Allowable fast charge current: or less Voltage de coupure à la décharge : 2.0 V/élément - Discharge voltage cut off level: 2.0V/cell ou or plus higher Pb Pb Tension par élément : 2.0 V - Voltage level: 2.0V/cell Tension de charge maximale par élément V - (Lead-acid) Max. charge voltage:: 2.46 2.46V/cell Courant de charge rapide autorisé : 0.40.4C C ou moins - Allowable fast charge current: or less Voltage de coupure à la décharge : 1.75 1.75V/cell V/élément ou - Discharge voltage cut off level: or plus higher - 07 - Sauf erreurs et omissions, sous réserve de modifications. Attention cette traduction de la notice du charger e6650 est la propriété de la société Beez2B. Toute reproduction même partielle est interdite. Copyright © 2011 Beez2B NOTICES D’AVERTISSEMENTS WARNING AND SAFETY NOTESET DE SECURITE To avoid circuit between the charge lead always connect Afin d’éviter toutshort court-circuit, prenez l’habitude de raccorder d’abord les cable to the first, then connect the battery. câblesthe de charge charge au chargeur et charger ensuite les batteries. Pour débranchez Reverse the sequence when disconnecting. procédez inversement. Do not connect more than one battery pack to this charger at Ne jamais any connectez one time. plus d’une batterie à la fois au chargeur. Never attempt to charge or discharge thede following of : Ne jamais tenter de charger ou décharger les types batteriestypes suivants batteries. Un pack de batterie qui contient différents types d’éléments (y compris différentes A batterymarques). pack which consists of different types of cells (including different manufacturers) A battery that is already fully charged or just slightly discharged. complètement Non-rechargeable batteries (Explosion hazard). Batteries that require a different charge technique from NiCd, NiMh, LiPo or Gel cell (Pb, Lead acid). A faulty or damaged battery. NiMH, LiPo ou Pb A battery fitted with an integral charge circuit or a protection circuit. Batteries installed in a device or which are electrically linked to other components. protection Batteries that are not expressly stated by the manufacturer to be suitable for the currents the charger carries during the charge process. quement à d’autres composants. Please bear in mind the following points before commencing charging. Did the appropriate program suitable for the type of courantyou queselect peut livrer votre chargeur. battery you are charging? Did you set up adequate current for charging or discharging? Have you checked the battery voltage? Lithium battery packs can be wired in parallel and in series, i.e. a 2 cell pack can be 3.7V (in parallel) or 7.4V (in series). - 08 - Sauf erreurs et omissions, sous réserve de modifications. Attention cette traduction de la notice du charger e6650 est la propriété de la société Beez2B. Toute reproduction même partielle est interdite. Copyright © 2011 Beez2B NOTICES D’AVERTISSEMENTS ET DE SECURITE WARNING AND SAFETY NOTES Have you des checked all connections are firmlaand secure? Assurez-vous pointsthat suivants avant de commencer charge : Make sure there are no intermittent contacts at any point in the circuit. Est-ce que le programme adéquat a été choisi pour le type de batterie que vous voulez utiliser ? Charging During charge process, specific of electrical energy is -vous choisi un courantade charge quantity ou de décharge adéquat ? fed into the battery. The charge quantity is calculated by multiplying charge current by charge time. The maximum -vous vérifié le voltage de la batterie ? Des batteries Lithium peupermissible charge current varies depending on the battery type vent être mises en parallèle ou en série, un pack de 2 éléments peut être or its performance, and can be found in the information by the 3.7 V (en parallèle) ou 7.4 V (en série). battery manufacturer. Only batteries that are expressly stated to be capable of quick-charge are allowed to be charged at rates -elles bien assurées sans contact intermittent et higher than the standard charge current. sans risques de court-circuit ? Connect the battery to the terminal of the charger: red is positive Charge and black is negative. Due to the difference between resistance cablede and connector, thedépend charger detect resistance of Leof courant charge maximale du can type not de batterie ou de sa the batterycette pack,info thepeut essential requirement the charger to performance, être trouvée dans les for instructions du fabriwork properlyles isbatteries that the pour charge lead should be of d’être adequate cant. Seulement lesquelles il est stipulé capable pour une charge rapide peuvent être chargées à une charge plus puissanconductor cross-section, and high quality connectors which are te normally que la charge standard.should be fitted to both ends. gold-plated EnAlways connectant une au chargeur rouge est positif et noirpertaining est refer to batterie the manual by the :battery manufacturer négatif. Assurez-vous que les câbles de connexions ontcurrent une section to charging methods, recommended charging and assez importante que les connecteurs de haute qualité, plaqué norchargingettime. Especially, thesont Lithium battery should be or charged malement. Ceci réduit la résistance et permet une fonction correcte du according the charging instruction provided by the manufacturer chargeur. strictly. Contrôler toujours les be polarités etthe suivez les recommandations de charge Attention should paid to connection of Lithium battery duespecially. fabriquant des batteries Ceci concerne les batteries Lithium. Veuillez noter que les éléments Lithium peuvent être to assemblés en parallèle ou en série. Do not attempt disassemble the battery pack Assurez-vous arbitrarily. que la tension et la capacité sont correctes avant de charger. Ne désassemblez jamais les packs de batterie. - 09 - Sauf erreurs et omissions, sous réserve de modifications. Attention cette traduction de la notice du charger e6650 est la propriété de la société Beez2B. Toute reproduction même partielle est interdite. Copyright © 2011 Beez2B NOTICES WARNINGD’AVERTISSEMENTS AND SAFETY NOTES ET DE SECURITE Please get highlighted that Lithium battery packs can be wired in Décharge parallel and in series. In the parallel connection, the battery‟s capacity calculated battery‟s capacity by Le but principalisde déchargerby estmultiplying d’enlever ousingle de réduire la capacité restante number of cells with total voltage stay the same. The voltage‟s de lathe batterie. La décharge demande autant d’attention que la charge. Veillez imbalance may cause fire minimale or explosion .Lithium Les battery is Lià définir correctement la tension à la décharge. éléments recommended to charge in series. thium sont très sensibles pour ceci, si elles sont déchargées en dessous de la tension minimale, elles perdront rapi-dement leur capacité ou deviennent totalement inutilisable. Discharging The main purpose of discharging is to clean residual capacity of the battery, or to reduce the battery?voltage to a defined level. Certaines batteries rechargeables & NiMH) un effet mémoire. Si as The same attention should(NiCd be paid to theont discharging process ellescharging. sont partiellement et puisvoltage rechargées, ellesbe peuvent retenir » The finalvidées discharge should set up«correctly ceci to et elles utiliser uniquement cette partie decan leur not capacité. Un cycle de avoidvont deep-discharging. Lithium battery be discharged décharge peutthan mener batterie à un cycle normal d’utilisation. to lower thelaminimum voltage, or it will cause a rapid loss of Il n’est pas conseillé de décharger complètement et puis recharger des packs capacity or a total failure. Generally, Lithium battery doesn‟t need batteries GardezPlease les toujours partiellement charger. Pour voltage optimaliser to beLithium. discharged. pay attention to the minimum of la capacité maximale Lithium nouveaux, on peut les soumettre à Lithium battery d’éléments to protect the battery. une dizaine de cycles de charge. Some rechargeable batteries have a memory effect. If they are partly used and recharged before the whole charge is accomplished, they remember this and will only use that part of their capacity next time. This is a „memory effect‟ It is said that NiCd and NiMH batteries are suffering from memory effect. NiCd has more memory effect than NiMH. Lithium batteries are recommended to be discharged partially rather than fully discharged. Frequent full discharging should be avoided if possible. Instead, charge the battery more often or use a battery of larger capacity.Full capacity cannot be used until it has been subjected to 10 or more charge cycles. The cyclic process of charge and discharge will optimize the capacity of battery pack. - 10 - Sauf erreurs et omissions, sous réserve de modifications. Attention cette traduction de la notice du charger e6650 est la propriété de la société Beez2B. Toute reproduction même partielle est interdite. Copyright © 2011 Beez2B PROGRAMME PROGRAMFLOW FLOWCHART CHART PROGRAM FLOW Programme flowCHART chart - 11 - Sauf erreurs et omissions, sous réserve de modifications. Attention cette traduction de la notice du charger e6650 est la propriété de la société Beez2B. Toute reproduction même partielle est interdite. Copyright © 2011 Beez2B MENUPARAMETER SETUP (REGLAGE INITIAL SETUPUTILISATEUR) (USERS SET UP) INITIAL PARAMETER SETUP (USERS SET UP) Menu setup (réglage utilisateur) As default this charger will be set to typical user settings when it is Le chargeur e6650 peut fonctionner avec ses réglages par défaut pour un usage connected to AC 110-240V or DC 11-18V for the first time. The de base effectué en usine. L’écran affiche les informa-tions en séquences et screen displays the following information in sequence and the user l’utilisateur peut modifier les paramètres à chaque écran. can change the parameter on each screen. Lorsque vous désirez changer les valeurs des paramètres dans un programme If yousur need to alterSTART the parameter value in the program, press appuyez la touche / ENTER pour faire clignoter l’écran et changer “Start/Enter” keylestotouches make it«blink then change value with “INC” alors la valeur avec Status ». La valeur the est enregistrée en apor “DEC” key.START The value will. be stored by pressing “Start/Enter” key puyant la touche / ENTER once. User Ecransetup initial starting screen. USER SET PROGRAM-> INC LiFe V.Type 3.3V - + DEC INC DEC INC LiPo/LiIo/LiFe CHK Time 10min Il existe 3 types de batteries Lithium: LiFe (3,3V) LiLo (3,6V) et LiPo (3,7V) avec chacune une ten-sion The screen displays Ilthe voltage of nominale différente. estnominal important de confirmer Lithium battery. There are kinds quelle type de batterie serathree chargée carof enLithium cas d’erbattery: LiFe(3.3V), Lilo(3.6V) or sa LiPo(3.7V). reur celle-ci peut exploser durant charge. This is very important so you have to check the battery carefully and set it up correctly. If it is different from correct value the battery may be Le chargeur e6650 détecte automatiquement le exploded during charge process. nombre d’éléments du pack de batteries Li-thium au début de la chargethe oucell décharge. Une batterie dée6650 recognize count of Lithium battery chargée de trop néanmoinsofêtre perçue automatically at peut the beginning charge or incorrectement.process Afin d’éviter cettefrom erreur vous pouvez discharge to avoid erroneous programmer le temps durantdischarged lequel le processeur setting by user. But deeply battery vérifie nombre d’éléments, de l’ordre can be le perceived incorrectly. qui To est prevent the de 10 minutes normale-ment. batteries plus error, you can set the time Pour term des to verify the àcell count the processor. Normally, minutesd’aughauteby capacité (+ de 2000mAh) il est10conseillé are enough to perceive cell count correctly. menter ce temps. Si vousthe utiliser des batteries à plus For thecapacité battery avec of larger capacity, you may faible un temps programmé trop long, extend the time term. But if termine you set avec the time il est possible que la charge un déterm to long for the of smaller compte incorrect desbattery éléments. Veuillezcapacity, ne chan-ger the or discharge process can qu’en be finished quecharge les valeurs initiales programmées cas de within time termdewith the erroneous chargethe d’éléments grande capacité. cell count. This may cause the fatal result. If the processor - 12 - Sauf erreurs et omissions, sous réserve de modifications. Attention cette traduction de la notice du charger e6650 est la propriété de la société Beez2B. Toute reproduction même partielle est interdite. Copyright © 2011 Beez2B MENUPARAMETER SETUP (REGLAGE INITIAL SETUPUTILISATEUR) (USERS SET UP) DEC INC NIMH Sensitivity D.Peak Default - + DEC INC DEC INC NICD Sensitivity D.Peak Default - + DEC INC DEC INC Temp. Cut-off ON 80C - + DEC INC DEC - + DEC INC INC Waste time CHG/DCHG 5min - + DEC INC DEC - + DEC INC INC recognizes the cell count incorrectly at the beginning of charge or discharge process, you may extend the time. Otherwise, youlors hadd’une better Cet écran montre la tension de coupe use withenthe default value. charge “Delta Peak” de batteries NiMH et NiCd. Cette valeur doit afficher de 5mV à 20mV par éléThis shows the trigger voltage for automatic ment. Si la coupure est trop élevée, il est possible charge termination of NiMH and NiCd battery. de surcharger la batterie et de l’endommager. Si The effective value ranges from 5 to 20mV per vousIfprogrammez la coupure trophigher, bas, lathere batterie cell. the trigger voltage is set is se chargera pas complètement. Veuillez vous anedanger of overcharging the battery; if it is set référerthere aux caractéristiques votre batterie. La lower, is a possibility de of premature programmation initiale estthe de 12mV pour NiCd et termination. Please refer technical 7mV pour NiMH. specification of the battery. (NiCd default: 12mV, NiMH default: 7mV) Vous pouvez également utiliser la sortie à 3 broches, à gauche du chargeur. C’est une porte USB ou pour le branchement de la sonde thermique. Sélectionnez la fonction choisie via l’écran et les touches + et -. Si vous sélectionnez le programme “Température” veuil-lez connecter la sonde therAn optional feature using temperature probe mique. La température coupure peut contacting the surface maximale of battery,de the temperature être programmée afinoff. que chargeur sa cut-off can be on or If le it is on, set termine the charge suivant la température choisie. Si vous maximum temperature at which the charger sélectionnez programme USB, veuillez connecter should allow le battery to reach during charge. le cordon USB à reaches votre ordinateur. Once a battery this temperatureduring charge, the process will be terminated to protect the battery. Avec le programme inclus vous pouvez suivre le The battery becomes warm after cycles of processus de charge et décharge sur votre PC. charge/discharge process. The program will Lorsque vous Chargez/Déchargez votre batterie insert a time delay after each charge/discharge suivant un cycle pré choisi, la batterie chauffe process to allow the battery enough time to cool souvent durant le cycle. Ce programme permet de down before beginning next cycle of charge/ programmer un temps devalid 0 à 60 minutes, laissant discharge process. The value ranges from temps de refroidir à la batterie entre chaque 0leto 60 minutes. charge/décharge. - 13 - Sauf erreurs et omissions, sous réserve de modifications. Attention cette traduction de la notice du charger e6650 est la propriété de la société Beez2B. Toute reproduction même partielle est interdite. Copyright © 2011 Beez2B MENU SETUP (REGLAGE UTILISATEUR) INITIAL PARAMETER SETUP (USERS SET UP) DEC INC Safety time ON 120min - + DEC INC - + DEC INC When the charge process starts, the integrated Quand le processus de charge démarre, le « safety safety timer starts to run simultaneously. If error timer » intégré démarre. Si une erreur est détectée detected or the termination circuit can not detect ou le circuit de delta peak ne peut pas détecter si whether the battery is fully charged or not, this la batterie est totalement chargée ou pas, ce prounit is programmed to prevent overcharging. grammerefer évitetolathe surcharge. Please below statement to calculate the timer you set. CalculSafe du temps deCalculation charge Timer Quand on veut charger une batterie NiCd ou NiMH, ondivide doit diviser la capacitéby du current, pack par When charging NiCd or NiMH batteries, the capacity le courant charge, diviser résultat 11,9. Mettez of ce chiffre comme nombre de then de divide thepuis result byle11.9, setpar this number minutes as the value minu-tes pour la valeur le menu « safety timerstopped » . Si le chargeur s’arrête à ce moment, for safety timer dans setting. If the charger at this time threshold, environ 140 % de la capacité sera injectée dans la batterie. about 140% of the capacity will have been fed into the battery. Exemple : For example: Capacité Courant Temps de charge Current Safety(2000 Time 2000 Capacity mAh 2.0 A / 2.0 = 1000) / 11.9 = 84 minutes 2.0A (2000/2.0=1000)/11.9=84 3300 2000mAh mAh 3.0 A (3300 / 3.0 = 1100) / 11.9 =minutes 92 minutes 1000 3300mAh mAh 1.2 A (1000 / 1.2 = 833) / 11.9 = minutes 70 minutes 3.0A (3300/3.0=1100)/11.9=92 1000mAh DEC 1.2A INC Capacity Cut-Off ON 5000mAh - + DEC INC DEC - + DEC INC INC Key Beep ON Buzzer ON - + DEC INC DEC (1000/1.2=833)/11.9=70 minutes Ce programme fixe la capacité de charge maximale qui The program provides maximum capacity sera utilisé function. pendant ce processus de charge. Si la tension protection If the Delta-peak voltage au sommet du “Delta or Peak” n’est pas détecté can not be detected the safety timer timesou la minuteriethe est charge expirée,process le présent arrêtera la charge out, willsystème stop automatically, automatiquement lorsque la capacité estmaximum atteinte. when the battery reaches the user-set charge capacity, The beep to confirm users' operation sounds every time a“beep” buttondeisconfirmation pressed. Thepeut beep orenclenché Le bruitage être melody sounds at various timeslors-que during operation ou arrêté. Le Buzzer qui informe le chargeur to confirm change. entre dans different un modemode particulier, peutThese également être functions be switched on or off. enclenchécan ou arrêté. INC Input Power Low Cut-Off 10.0V This function monitors the voltage of the input Ce programme indique la tension d’entrée en courant battery power thisbaisse charger. If the voltage continu used (DC). to Si la tension en des-sous de celle que is lower user-set value, the program will autovous avezthan programmée, l’opération se terminera end forcibly to protect the input battery. matiquement. - 14 - Sauf erreurs et omissions, sous réserve de modifications. Attention cette traduction de la notice du charger e6650 est la propriété de la société Beez2B. Toute reproduction même partielle est interdite. Copyright © 2011 Beez2B PROGRAMMES DE GESTION DESPROGRAM BATTERIES LITHIUM (LiPo,Li-Ion,LiFe) LITHIUM (LIPO/LILON/LIFE) LITHIUM (LIPO/LILON/LIFE) Programmes de gestion des PROGRAM batteries Lithium (LiPo, Li-Ion, LiFe) The program is only suitable for lacharging/discharging Lithium(LiPo/ Ces programmes ne sont valables que pour charge et décharge de batteries Lithium LiIon/LiFe) batteries with nominal voltage of élément. 3.3/3.6/3.7V/cell. possédant une tension nominale dea3,3V, 3,6V and 3,7V par Ces batteries nécessiDifferent batteriesdehave technique. are two (CV) et tent des caractéristiques chargedifferent différentscharge et dépendant de leur There ension constante methods termed constant voltage constant current. The cou-rant constant (CC). Leas courant de charge varieand suivant sa capacité et ses caractéristicurrent varieslaaccording to batterytrès capacity andElle specification. ques.charge La tension finale durant charge est également importante. doit concorder avec The le type de batterie, mémoire 4,2V=LiPo, 4.1V=Li-ion et 6V=LiFe. Si lethe voltage final final voltagepour is very important; it should precisely match dépasse 1% durant le processus de charge la batterie exploser. courant et voltage voltage of the battery: LiPo is 4.2V, LiIonpeut is 4.1V andLeLiFe is 3.6V. nominaux pour le comptage d’éléments être détermines à la mise en charge. Le The current and voltage of thedoivent battery should be correctly set. bon programme êtretodéterminé charger la lorsqueplease vous désirez changer When youdoit want change pour the values ofbatterie. parameters, press les para-mètres dans le programme appuyez sur la touche START / ENTER pour faire clignoSTART/ENTER key to make it blink and then use DEC or INC to ter votre sélection, puis appuyez sur la touche ▲ ou ▼ pour changer la valeur. Confirmez change the value. Then press START/ENTER key again to store the avec la touche START / ENTER pour garder la valeur. value. CHARGING LITHIUMLithium BATTERY Charge d’uneOF batterie The left side of the first line shows the type La valeur à gauche de la seconde ligne indique of battery you choose. The value on the left le courant de charge et celle de la seconde of the second line of the charger is current ligne à droite indique le voltage du pack d’acuser set, After setting the current and - + - + cus. Après avoir choisi le courant et le voltage DEC INC DEC INC voltage, press START/ENTER key for more appuyez sur START / ENTER 3 seBatt type Start than 3 seconds to start the pendant process.(charge „>3 seconds‟ condes pour démarrer le processus. Courant Stop Enter current: 0.1-5.0A, voltage: 3.7-22.2V). de charge : 0.1- 5.0A. voltage : 3.7-22.2 v. This displays the number of cells you set up R:3SER S:3SER processor shows the «and R »the vous montre ledetects.”R” nombre d’éléments déCONFIRM(ENTER) number detected charger tectés paroflecells chargeur et « Sby» the le nombre sélecand “S”par is the number of cells set by you at tion-né l’utilisateur. Si les nombres affichés the previous screen. If both numbers are sont identiques appuyez sur START / ENTER Start identical you can start charging by press Enter pour démarrer la charge. Sinon appuyez sur START/ENTER If not, press BATT BATT.TYPE / STOPbutton. pour retourner et modifier. TYPE/STOP button to go back to previous screen to carefully check the number of cells Li3s 1.2A 12.59V Cet écran affiche l’évolution durant la charge. of the battery pack before going ahead. CHG 022:43 00682 Appuyez sur BATT.TYPE / STOP pour arrêter la This screen shows the real-time status charge. Number Charging Battery during charge process. Press BATT TYPE/ of cells time voltage Charging Charged STOP key once to stop the charge process. LiPo CHARGE 2.0A 11.1V(3S) current capacity - 15 - Sauf erreurs et omissions, sous réserve de modifications. Attention cette traduction de la notice du charger e6650 est la propriété de la société Beez2B. Toute reproduction même partielle est interdite. Copyright © 2011 Beez2B CHARGER UNE BATTERIE LITHIUMINEN MODE « CHARGE CHARGING LITHIUM BATTERY THE CHARGE MODE » CHARGING LITHIUMLithium BATTERY THE CHARGE Charger une batterie enINmode « chargeMODE » This charging mode is for charging Li-Po/Ion/Fe battery without Le mode de charge « charge » est pour charger des batteries LiPo / balance Li-ion / LiFe lead. sans câble balanceur BALANCE OF LITHIUM BATTERY Charger uneCHARGING batterie Lithium The left side of thedefirst line shows type La valeur à gauche la seconde lignethe indique LiPo BALANCE of battery you choose. The value on the le courant de charge et celle de la seconde left 2.0A 11.1V(3S) of theà second line of le the charger current ligne droite indique voltage du is pack d’acuser set, After setting the current and - + - + cus. Après avoir choisi le courant et le voltage DEC INC DEC INC voltage, press START/ENTER key for more appuyez sur START / ENTER pendant 3 seBatt type Start than 3 seconds to start the process.(charge „>3 seconds‟ condes pour démarrer le processus. Courant Stop Enter current: 0.1-5.0A, voltage: 3.7-22.2V). de charge : 0.1- 5.0A. voltage : 3.7-22.2 v. This displays the number of cells you set up R:3SER S:3SER processor shows the «and R »the vous montre ledetects.”R” nombre d’éléments déCONFIRM(ENTER) number detected charger tectés paroflecells chargeur et « Sby» the le nombre sélecand “S”par is the number of cells set by you at tion-né l’utilisateur. Si les nombres affichés the previous screen. If both numbers are sont identiques appuyez sur START / ENTER Start identical you can start charging by press Enter pour démarrer la charge. Sinon appuyez sur START/ENTER If not, press BATT BATT.TYPE / STOPbutton. pour retourner et modifier. TYPE/STOP button to go back to previous screen toaffiche carefully check the number of cells Li3s 1.2A 12.59V Cet écran l’évolution durant la charge. of the battery pack before going ahead. BAL 022:43 00682 Appuyez sur BATT.TYPE / STOP pour arrêter la Number Charging of cells time charge. This screen shows the real-time status during charge process. Press BATT TYPE/ Charged STOP key once to stop the charge process. Battery voltage Charging current capacity Charger une batterie enINmode « balance » CHARGING LITHIUMLithium BATTERY THE BALANCE MODE This ce function balancing the voltage of Lithium-polymer battery Dans mode, is le for procédé de charge est différent d’un mode de charge cells whilele charging. the balance mode,vérifie the battery needs to have ordinaire. processeurIninterne du chargeur le voltage de chaque a balance to connect to thelaindividual balance port the right élément de lead la batterie et contrôle quantité de courant de at chaque éléside of the charger. And you need to connect the battery's power lead ment pour régulariser le voltage. Vous pouvez déterminer le courant de to the output of charger. charge du pack d’accus. Avant de procéder vérifiez attentivement les Charging in this mode is different from the normal modes, because connexions de l’équilibreur et du chargeur. the built-in processor monitors voltage of individual cell and control input current fed into each cell to equalized voltage of individual cell. - 16 - Sauf erreurs et omissions, sous réserve de modifications. Attention cette traduction de la notice du charger e6650 est la propriété de la société Beez2B. Toute reproduction même partielle est interdite. Copyright © 2011 Beez2B CHARGE RAPIDEOF D’UNE BATTERIE LITHIUM FAST CHARGING LITHIUM BATTERY FASTrapide CHARGING OFbatterie LITHIUM Lithium BATTERY Charge d’une The value on the left of theligne second linesle La valeur à gauche de laside seconde indique sets thede charge on the courant chargecurrent. et celle The de lavalue seconde ligne à right side of the seconddu lines sets the battery droite indique le voltage pack d’accus. Après pack's voltage. After setting current and - + avoir choisi le courant et le voltage appuyez sur DEC INC voltage, press STAR/ENTER for more than START / ENTER pendant 3 secondes pour démar3 seconds to start the process. Start „>3 seconds‟ rer le processus. Enter LiPo FAST CHG 2.0A 11.1V(3S) - + DEC INC Batt type Stop R:3SER S:3SER CONFIRM(ENTER) Start Enter Li3s 2.0A 12.59V FAS 022:43 00682 This displays the number of cells you set up «and R »the vous montre le nombre d’éléments détecprocessor detects. “R” shows the tés par leofchargeur et « S » by le nombre sélectionnumber cells detected the charger and né par l’utilisateur. Si les nombres affichés sont “S” is the number of cells set by you at the identiques appuyezIf sur START / ENTER previous screen. both numbers arepour démarrer la charge. Sinon appuyezbysur identical you can start charging press BATT.TYPE / STOPbutton. pour retourner et modifier. START/ENTER If not, press BATT TYPE/STOP button to go back to previous screen to carefully check the number of cells of the battery pack before going ahead. Cet écran affiche l’évolution durant la charge. This screen shows the real-time status during Appuyez sur BATT.TYPE / STOP pour arrêter la charge process. Press BATT TYPE/STOP charge. key once to stop the charge process. Number Charging of cells time Current voltage battery Charging Supplied current capacity CHARGING BATTERYLithium IN THE FAST CHARGE MODE Charge rapideLITHIUM d’une batterie en mode charge Charging will become lower when it progress to the end of La fonctioncurrent « FAST CHG » sert à charger une batterie rapidement. Pendant charging. A specific CV process will be reduced to end the charging ce processus le chargeur diminue le courant de charge en at-teignant la fin process earlier. In fact, the charging current will goes to 1/5 when the de la charge. Le courant de charge sera réduit jusqu’à 1/5ième après 90% charging process comes to 1/10. Charging capacity will be little de la charge. La capacité de charge sera un peu plus faible, mais les temps smaller than normal charging, but charging time will be shortened de charge sont réduits fortement. accordingly. - 17 - Sauf erreurs et omissions, sous réserve de modifications. Attention cette traduction de la notice du charger e6650 est la propriété de la société Beez2B. Toute reproduction même partielle est interdite. Copyright © 2011 Beez2B MODE ENTRETIEN POUR BATTERIE LITHIUM STORAGE CONTROL OF LITHIUM BATTERY STORAGE CONTROL OF LITHIUM BATTERY Mode entretien pour batterie Lithium LiPo STORAGE 1.0A 11.1V(3S) - + DEC INC - + DEC INC At this you can setpeut up the current Avec cetscreen, écran, l’utilisateur entrer le and voltage of the battery pack. Charging courant de charge et la tension de la batterie à and discharging will make the batteries entre-tenir. En charge et décharge, le chargeur come to the voltage level of “Storage” state. donnera à la batterie son niveau de stockage. Batt type Start „>3 seconds‟ Stop Enter Li3s 1.0A 12.59V STO 022:43 00682 Cet écran montre situation durant le proThis screen showsla the real-time status cessus de Press chargeBATT décharge. Pour arrêter charging. TYPE/STOP keyce processus, appuyez sur BATT.TYPE once to stop the charge process. / STOP. Number Elapsed of cells time Current voltage battery Charge or Supplied discharge capacity current Charge d’une batterie Lithium en mode entretien CHARGING LITHIUM BATTERY IN THE STORAGE MODE This function for charging/discharging batteries areutilisée not used Ce mode sert àisconserver une batterie Lithium qui ne which sera pas at once.un This program designed détermine for charging of pendant moment. Ce is programme s’ilor estdischarging nécessaire de batteries specific original state. are 3.75V charger ouofdécharger la batterie à unThey niveau declassified tension etby cetypes: d’après la Lilo, 3.85V LiPo and 3.3V LiFe. The program will begin to discharge tension initiale de la batterie. Il existe plusieurs type de batte-ries Lithium if the original state of the battery exceeds the voltage level of storage. tels : LiIo=3,75V, LiPo=3,85V et LiFe=3,3V de tension par élément. Si la tension de la batterie est supérieure à sa valeur initia-le, le programme commencera par décharger la batterie à son meilleur niveau de conservation. - 18 - Sauf erreurs et omissions, sous réserve de modifications. Attention cette traduction de la notice du charger e6650 est la propriété de la société Beez2B. Toute reproduction même partielle est interdite. Copyright © 2011 Beez2B DECHARGER BATTERIE LITHIUM DISCHARGINGUNE OF LITHIUM BATTERY DISCHARGING OF LITHIUM BATTERY Décharger une batterie Lithium The value discharge current on the leftde La valeur duofcourant de décharge à gauche can notneexceed 1C, and the1C value the à l’écran peut pas dépasser et laon valeur right can not be descendre under the en voltage droite ne pourra dessous de la recommended by the par manufacturer avoid - + - + tension recommandée le fabricantto afin DEC INC DEC INC deep discharging. Press for d’éviter une décharge tropSTART/ENTER profonde. Appuyez more than 3 seconds to start discharging. Batt type Start „>3 seconds‟ sur START / ENTER pendant plus de 3 secondes Stop Enter pour démarrer la décharge. This shows the real-time status of Li3s 0.4A 12.59V Cet écran affiche discharging, youl’évolution can pressdurant BATT la déDSC 022:43 00682 charge. Appuyez / STOP pour TYPE/STOP keysur to BATT.TYPE stop discharging. arrêter la décharge. Number Elapsed Battery LiPo DISCHARGE 1.0A 11.1V(3S) of cells time voltage Discharge Discharged current capacity BATTERY VOL ERR CELL LOW VOL Si cet écran apparaît, le microprocesseur a The processor detects voltage of one cell is déterminé que la tension d’un élément du pack too low. de batterie est trop faible. INC 4.14 4.16 4.09 2.18 0.00 0.00 Cet montre liste des tensions de chaque Theécran 4th cell wasladamaged. The value of élément. Dansbe ce zero cas c’est l’élément 4 qui est voltage may if disconnection occurs. défectueux. VOLTAGEde BALANCING MONITORING IN THEla décharge Equilibreur tension etAND surveillance pendant DISCHARGE PROCESS Le microprocesseur surveille la tension de chaque élément individuel de batterie Lithium The processor monitors voltage of each cell when thechaque battery packs durant le mode de charge d’entretien et déchar-ge en équilibrant cellule à la are during and “discharging” If voltage of any même tension.its Les“storage” deux connecteurs de la batterie, process. c.à.d. la multi-fiche d’équilibrage cellque is abnormal, show errorêtre message and ainsi le connecteure6650 positif /will négatif doivent connectés au terminate chargeur. Si the la tension program forcibly. So if varie thereanormalement is battery damage disconnection, you d’une ou plusieurs éléments durant laor charge, le e6650 arrête la charge et affiche “ERROR” sur l’écran. le pack ne contient can see the error message andVérifiez pressd’abords INC to siknow which cell ispas un élément défectueux ou une mauvaise soudure au connecteur. Afin de déterminer quel damaged. élément est défectueux appuyez le bouton “▲” afin d’afficher le message. - 19 - Sauf erreurs et omissions, sous réserve de modifications. Attention cette traduction de la notice du charger e6650 est la propriété de la société Beez2B. Toute reproduction même partielle est interdite. Copyright © 2011 Beez2B CHARGE D’UNE BATTERIE NiCd/NiMH CHARGING OF NICD/NIMH BATTERY CHARGING OF NICD/NIMH BATTERY Charge d’une batterie NiCd/NiMH This programcharge is for la charging of NiCd/NiMH Ce programme batterie suivant le courant de batteries with R/C models charge queassociated vous avez installé. Appuyez sur START/ applications. Youl’application can pressetSTART/ENTER ENTER pour choisir puis poussez sur INC key to make it blinklaand then INC or DEC to ou DEC pour changer valeur des paramètres. Poussez - + DEC INC sur START/ENTER pour sauver les valeurs. change the parameter value. Press Start „>3 seconds‟ START/ENTER key to store the value. NIMH CHARGE Aut CUR LIMIT 5.0A - + DEC INC Batt type Stop Enter NIMH 2.0A 7.42V CHG 022:45 00890 The screen real-time status. L’écran afficheshows l’état dethe charge. Pour arrêter la charge Press BATT key tola end appuyez: STARTTYPE/STOP / ENTER; Maintenez tou- the program. The sound will emitted to indicates che>3secondes. Le son audible vous indique l’arrêt du the end of program. processus. Battery Elapsed Battery type time voltage Charge current Charged capacity CHARGING NICD/NIMH BATTERY INen THE CHARGE MODE Charge d’une batterie NiCd/NiMH mode charge This program ont charge the battery usingetthe currentlesyou setNickel up. In the Ces programmes pour fonction de charger décharger accus Metal“auto” ou state, you shouldlargement set up the upper of the charge current to Hydride Nickel Cadmium utilisés pourlimit les modèles radio-commandés. avoid damage excessive feeding batteries of low Vérifiez les flux de by voltage de chaque type decurrent. batteries Some pour une charge automatiresistance and capacity can programme lead to higher current in the “auto” que. Vous trouverez dans le menu des sensibilités adaptées soit pour les accus NiMH mode. ou NiCdBut car les fournis sont différents. Pour changer entre le charging in courants the manual mode, it will charge with the mode Autoyou et Manual, poussez sur INCitet DEC in simultanément. Voltage rapide current set. You can make blink the current Note field :and press de charge : 1C-2C. INC andacceptable DEC simultaneously to swap between Auto and Manual Mode. NOTE: Allowable fast charge current: 1C-2C Décharge d’une batterie NiCd/NiMH DISCHARGE OF NICD/NIMH BATTERY NIMH DISCHARGE 1.0A 11.5A - + - + Set charge current ondécharge the leftsur and the final Sélectionnez courant de la gauche et voltage on the right. Range of thesur charge voltage final trouvé en fin de processus la droite current is La 0.1-1.0A; range ofdefinal voltage de l’écran. plage de courants décharge va deis 0.1A à 1.0A celle de tension de 0.1V~25V. Appuyez 0.1-25.0V. Press START/ENTER key for sur START Pour démarrer la décharge apmore than/ ENTER. 3 seconds to start the program. DEC INC DEC INC Batt type Start „>3 seconds‟ puyez START / ENTER pendant 3 secondes. Stop Enter NIMH 1.0A 7.42V DSC 022:45 00890 Battery Elapsed Battery type time voltage Discharge current Discharged capacity The screen indicates the discharging state. You can press START/ENTER key to alter L’écran affiche l’état de décharge. Vous pouvez discharge current.dePress START/ENTER modifier le courant décharge en pressant une again to store the value. Press BATT fois pendant l’opération START / ENTER . Poussez TYPE/STOP key toarrêter stop discharging. BATT TYPE/STOP pour la décharge. LeThe son émis voussound indiquealerts la fin du emitted theprocessus. end of discharging. - 20 - Sauf erreurs et omissions, sous réserve de modifications. Attention cette traduction de la notice du charger e6650 est la propriété de la société Beez2B. Toute reproduction même partielle est interdite. Copyright © 2011 Beez2B CHARGE/DECHARGE ET CYCLE DE CHARGE ET DE DECHARGE CHARGE/DISCHARGE AND DISCHARGE/CHARGE CYCLE D’UNE BATTERIE NiCd/NiMH OF NICD/NIMH BATTERY TABLE DES MATIERES CHARGE/DISCHARGE AND et DISCHARGE/CHARGE Charge/décharge et cycle de chrge de déch. d’une batterieCYCLE NiCd/NiMH OF NICD/NIMH BATTERY NIMH CYCLE DCHG>CHG 3 - + - + You can set up sequence onlathe left and Réglez la séquence visible sur gauche et lethe number de of cycles cyclessur onlathe right.Le Range of de the nombre droite. nombre cycle number 1-5. séquences varieisde 1 à 5 fois. DEC INC DEC INC Batt type Start „>3 seconds‟ Stop Enter NIMH 1.0A 7.42V D>C 022:45 00890 Battery Elapsed type time Battery voltage Poussez BATTTYPE/STOP TYPE/STOP pour Press BATT keyarrêter to stople proprogram,vous you pouvez can press START/ENTER gramme, changer le courant dekey to alter charge current. The/sound décharge en pressant START ENTER.indicates Le son the end program. émis vousofindique la fin du processus. Discharge Discharged or charge or charged A current capacity DCHG 1 1314mAh CHG 1 1430mAh la fin du processus, vous pouvez voir les capaciWhen it approaches to the you can see tés électriques de charges et end, décharges de chathe capacity of the battery being charged or que cycle. Poussez sur INC or DEC pour voir le discharged. You can press INC or DEC key résultat de chaque cycle sur le display. to display result of each cycle. CHARGING OF THE BATTERY Charger une batterie auPB plomb Set up the charge current on the left and Réglez le courant de charge à gauche de l’énominal voltage on the right. Range of cran et le voltage nominal de la batterie sur la current is 0.1-5.0A, the voltage should droite. Les plages de courant de charge vont match the battery being charged. Press - + - + de 0.1~5.0A. Démarrez la charge en pressant DEC INC DEC INC START/ENTER key for more than 3 seconds le bouton START / ENTER pendant plus de 3 Batt type Start „>3 seconds‟ to start charging. Stop Enter secondes. The screen displays the real-time Pb-6 4.0A 12.59V L’écran affiche l’étatPress du processus de charge. discharging status. START/ENTER CHG 022:43 00682 Pourtoarrêter la charge pressez touche key alter discharge current.laPress BATT.TYPE / STOPkey 1 fois. Unto avertissement START/ENTER again store the Battery Elapsed Battery type time voltage sonore confirme fin set. de l’opération. parameter valuelayou Press BATT Charge Charged TYPE/STOP key to end the program. Pb CHARGE 4.0A 12.0V(6P) current capacity - 21 - Sauf erreurs et omissions, sous réserve de modifications. Attention cette traduction de la notice du charger e6650 est la propriété de la société Beez2B. Toute reproduction même partielle est interdite. Copyright © 2011 Beez2B CHARGE/DISCHARGE AND DISCHARGE/CHARGE CYCLE OF NICD/NIMH BATTERY CHARGE/DISCHARGE AND DISCHARGE/CHARGE CYCLE OF NICD/NIMH BATTERY You can set up sequence on the left and the number of cycles on the right. Range of the cycle number is 1-5. NIMH CYCLE DCHG>CHG 3 - + - + DEC INC DEC INC Batt type Start „>3 seconds‟ Stop Enter NIMH 1.0A 7.42V D>C 022:45 00890 Battery Elapsed type time Battery voltage Discharge Discharged or charge or charged current capacity DCHG 1 1314mAh CHG 1 1430mAh Press BATT TYPE/STOP key to stop program, you can press START/ENTER key to alter charge current. The sound indicates the end of program. When it approaches to the end, you can see the capacity of the battery being charged or discharged. You can press INC or DEC key to display result of each cycle. CHARGING OF THE PB BATTERY Set up the charge current on the left and Pb CHARGE nominal voltage on the right. Range of 4.0A 12.0V(6P) current is 0.1-5.0A, the voltage should match the battery being charged. Press - + - + DEC INC DEC INC START/ENTER key for more than 3 seconds Batt type Start „>3 seconds‟ to start charging. Stop Enter Pb-6 4.0A 12.59V CHG 022:43 00682 Battery Elapsed type time Charge current Battery voltage Charged capacity The screen displays the real-time discharging status. Press START/ENTER key to alter discharge current. Press START/ENTER key again to store the parameter value you set. Press BATT TYPE/STOP key to end the program. - 21 - Sauf erreurs et omissions, sous réserve de modifications. Attention cette traduction de la notice du charger e6650 est la propriété de la société Beez2B. Toute reproduction même partielle est interdite. Copyright © 2011 Beez2B DECHARGE D’UNE BATTERIE au plomb DISCHARGING OF THE PB BATTERY DATA STORAGE PROGRAM de données Programme de sauvegarde For your convenience, e6650 has adedata storage and load Le chargeur e6650 possède un programme stockage de données pourprogram. votre faciliIt can fivevous battery data representing the respective té. Cettestore fonction permet de stocker 5 configurations différentesspecifications par numéros of batteries. can call individuelles back the data whenbatterie charging or discharging représentant lesYou spécifications de chaque en utilisation. Chaque configuration peut up êtrethe appelée pour effectuer les tâches de charge et décharge without setting program again. Press START/ENTER key tode make it blink, and use INC or DEC todevoir set up the parameter. batteries sans configurer le système à chaque fois. Enfoncez la touche START/ENTER pour le faire clignoter et poussez INC ou DEC pour mettre les paramètres. PROGRAM SELECT SAVE DATA Start Enter En mettant lesparameter paramètresinles processus de Setting of the the screen will not affect charge and discharge process. charge outhe de décharge ne sera pas affecté. Ils They just present the specification of thede la représentent uniquement la spécification battery. example is NiMH batteryd’un pack, batterie.The L’exemple montre le voltage pack including 12 cells, Ah. d’accus NiMH avec the unecapacity capacité is de3000m 3000mAh (12 éléments). SAVE [01] NiMH 14.4V 3000mHh Voltage Data Capacity number Type of battery Batt type Start „>3 seconds‟ Stop Enter Vous programmez de charSet uppouvez the charge current le incourant the manual ge tantor encurrent mode manuel mode auto mode, limit in qu’en the auto mode. avec limiteur deDEC courant. mode peut Press INC and key Chaque simultaneously to make the current field blinken to appuyant switch thesur être changé simultanément charge mode. INC et DEC lorsque l’affichage clignote. NiMH CHARGE At* CUR LIMIT 5.0A - + DEC INC DEC INC NiMH DISCHARGE* 1.0A 11.0V - + DEC INC Sélectionner un courant de décharge et voltage. un Set up the discharge current and final voltage final - + DEC INC DEC INC Ajuster le haut ladischarge séquencesequence de charge and / Set up vers the charge/ cycle number. décharge et le nombre de cycles NiMH CYCLE * DCHG>CHG 3 - + DEC INC Save ... - + Start DEC INC Enter „>3 seconds‟ Sauvegarder les données. Saving the data. - 23 - Sauf erreurs et omissions, sous réserve de modifications. Attention cette traduction de la notice du charger e6650 est la propriété de la société Beez2B. Toute reproduction même partielle est interdite. Copyright © 2011 Beez2B CHARGER LE PROGRAMME DE DONNEES LOAD DATA PROGRAM LOAD DATA PROGRAM de données Charger le programme program loadstockées the data at the “save data” program. CeThis programme utilise is les to données dansstored ‘Save Data’. (données sauvegardées) Pour charger lesPress donnéesSTART/ENTER appuyez START / ENTER pour clignoter champfield des données et sélectionnez le key tofaire make theledata blink and press INC numéro désiréfor en more utilisantthan les touches INC ou DECtoensuite pressez la touche START / ENTER penor DEC 3 seconds load the les data. numéro désiré en utilisant touches INC ou DEC ensuite pressez la touche START / ENTER pendant plus de 3 secondes. PROGRAM SELECT LOAD DATA Start Enter LOAD [01] NiMH 14.4V 3000mHh Choisissez le numéro de données stockées Choose the data number you want to call que vous voulez back. The data charger you want to call back will be displayed. Start Enter „>3 seconds‟ Load ... Loading thedonnées. data. Charger les - 24 - Sauf erreurs et omissions, sous réserve de modifications. Attention cette traduction de la notice du charger e6650 est la propriété de la société Beez2B. Toute reproduction même partielle est interdite. Copyright © 2011 Beez2B DIFFERENTES INFORMATIONS DURANT LA CHARGE/DECHARGE VARIOUS INFORMATION IN THE PROGRAM VARIOUS INFORMATION IN durant THE PROGRAM Différentes informations la charge/décharge Vous recevoirvarious de multiples informations pendant les charges/ Youpouvez can inquire information onsur thel’écran LCD LCD screen during the décharges. vousdischarging pressez DEC leprocess. chargeur Press vous montre configurations de l’utilisacharging Siand DECles key, the charger will teur et aussi affiche le voltage de can chaque élément pressant le bouton INC lorsque display users' setting. You press INCen key to monitor voltage of que le chargeur est the en mode équilibrage.. each cell while battery is connected with each port of the charger. End Voltage 12.6V(3S) ItQuand comes the final voltage whenlethe le to programme est terminé, courant program ended. final apparaît sur l’écran. DEC Capacity Cut-Off ON 5000mAh Displayed cut-off function is turn on La capacitécapacity de coupure apparaît sur l’écran. and the setting value of capacity. DEC Safety Timer ON 200min Displayed safety timerdeissécurité turn on apparaissent and duration Les données du timer of in minutes. surtime l’écran. DEC Temp. Cut-Off ON 80C 176F Displayed temperature function isappaturn Les données de coupurecut-off de température on. raissent sur l’écran. DEC Ext.Temp 26C DEC 4.14 4.16 4.09 0.00 0.00 0.00 Cet écran montre la température lue parwhen la The external temperature is displayed sonde extérieureprobe si employé. the temperature is used. The connected Si la battery batterieisest connecté with via leeach câbleport équilithrough cable; you can check voltage of breur, vous pouvez vérifier la tension de chaeach cell in the battery pack. When the cable que cellule dans le pack. Jusqu’à 6 cellules is connected with the ports on the charger, peuvent être montrées. the program will display voltage of up to 6 batteries. - 25 - Sauf erreurs et omissions, sous réserve de modifications. Attention cette traduction de la notice du charger e6650 est la propriété de la société Beez2B. Toute reproduction même partielle est interdite. Copyright © 2011 Beez2B MESSAGES D’ERREURS DE SECURITE WARNING AND ET ERROR MESSAGE WARNING AND ERROR Messages d’erreurs etMESSAGE de sécurité Le chargeur e6650 comprend de multiples fonctionsfor dethe protections et to de verify surveillance e6650 incorporates a variety of functions systems pour vérifier leand fonctionnement l’état de l’élec-tronique. Dans les casthe l’affichage processes the state ofetthe electronics. In case of tous an error vous renseigne sur la cause l’erreur avertissement sonore. screen will display the de cause of avec erroraussi andunemit an audible sound. REVERSE POLARITY Incorrect polarity connected. Polarité inversée. CONNECTION BREAK La batterie n’est pas bien connectée. Polarité. Rupture de Battery connection is interrupted. SHORT ERR Indique un court-circuit. les termination. câbles d’alimentation. Short-circuit of theVérifiez output INPUT VOL ERR La tension d’alimentation est trop faible. Input voltage incorrect. VOL SELECT ERR La tension de la batterie est incorrectement proThe voltage of theLithium battery pack has been grammée. selected incorrectly! BREAK DOWN The charger has malfunctioned for some Une mauvaise opération s’est passée. reason. Seek professional advice. connexion. BATTERY VOLTAGE CELL LOW VOL La tension du pack batterie est inférieure The voltage isdelower than which àiscelle set.que vous avez programmée. Vérifiez les nombre de votre pack Please check the number of d’éléments cells in the de batterie. battery pack. The voltage isélevée. higher thanleswhich set. de La tension est trop Vérifiez nombreis d’éléments votre packcheck de batterie. Please the number of cells in the battery pack. La tension d’un élément de batterie Lithium est Voltage of one celldeinvotre thepack battery pack is too trop faible. Vérifiez la tension de chaque élément, un par un. low, please check the voltage of each cell. BATTERY VOLTAGE CELL HIGH VOL La tension d’un élément de batterie Lithium est trop Voltage of one celldeinvotre thepack battery pack is too élevée.please Vérifiez lacheck tension de chaque élément, par un. high; the voltage of un each cell. BATTERY VOL ERR CELL CONNECT Wrong connection of the connector detected; Il y a une mauvaise connexion. Vérifiez les connecteurs et les please câbles. check the connector and cable. TEMP OVER ERR The internal interne temperature is too high, please La température est trop élevée, veuillez refroidir. cool down. CONTROL FAILURE The cannot control the feeding Erreurprocessor de contrôle. Vérifiez le courant d’entré. current, please repair it. BATTERY CHECK LOW VOLTAGE BATTERY CHECK HIGH VOLTAGE - 26 - Sauf erreurs et omissions, sous réserve de modifications. Attention cette traduction de la notice du charger e6650 est la propriété de la société Beez2B. Toute reproduction même partielle est interdite. Copyright © 2011 Beez2B SPECIFICATIONS SPECIFICATIONS SPECIFICATIONS Spécifications AC Input: Entrée AC : 100-240Volt 100-240 Volt DC Input: 11-18Volt Entrée DC : 11-18 Volt Circuit Power: Max. Charge Power 50W Puissance de charge max. 50W Max. Discharge Power 5W Puissance de décharge max. 5W Charge Current Range: 0.1-6.0A Courant de charge Discharge Current: 0.1-6.0A Range: 0.1-1.0A Courant décharge : 0.1-1.0ALiPo: 300mA/cell Currentde Drain For Balancing Courant balanceur : 300 NiCd/NiMH Battery CellmA/élément Count: 1-15Cells Comptage cellulesCell batterie NiCd/NiMH LiPo/LiFe/Lilon Count: 1-6Cells : 1-15 éléments Comptage batteries Pb batterycellules voltage: 2-20V LiPo/LiFe/LiLon : 1-6 élements Tension batterie au plomb : 2-20v Net Weight: 433g Poids net : 433g Dimension: 135x112x60.9mm Dimensions : 135x112x60.9mm WARRANTY AND SERVICE Garantie Weproduit guarantee this product to bevice freedeofconstruction manufacturing andau assembly Ce est garanti contre tout d’usine moment defects for a period of one year from the time of purchase. The de l’achat. Cette garantie ne couvre pas les composants détruits lors de warranty only applies to material or operational defects, which are l’usage du produit ou les modifications de l’ensemble ainsi que de la détépresent at t he time of purchase. During that period, we will repair or rioration due à l’utilisation de colles ou autres produits non spécifiés dans replace free of service charge for products deemed defective due to lathose notice. Nous nous réservons le droit de changer ou modifier les clauses causes. de cette garantie sans préavis. Nous déclinons toute responsabilité quant au dommages pouvanttorésulter deproof l’utilisation de ce produit, pas à You will be required produce of purchase (invoicen’étant or receipt). même de contrôler nous-mêmes le montage et son utilisationdamage correcte. This warranty is not valid for any damage or subsequent arising as a result of misuse, modification or as a result of failure to observe the procedures outlined in this manual. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. Manufactured by SKYRC TECHNOLOGY CO., LTD. www.skyrc.com - 27 - Sauf erreurs et omissions, sous réserve de modifications. Attention cette traduction de la notice du charger e6650 est la propriété de la société Beez2B. Toute reproduction même partielle est interdite. Copyright © 2011 Beez2B