Download Panasonic WV-TW310 Installation Guide
Transcript
Installation Guide Wearable Camera WV-TW310L/WV-TW310S WV-TW310LE/WV-TW310SE Model No. Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. The model number is abbreviated in some descriptions in this manual. For WV-TB311 (Optional) WARNING: • Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunlight, fire or the like. • The installation shall be carried out in accordance with all applicable installation rules. • The connections should comply with local electrical code. Caution: Do not open, crush, disassemble or dispose of batteries in fire with temperatures above (60 °C {140 °F}). Mishandling may cause burns, fire or explosions. Dispose of used batteries according to local ordinances and /or regulations. For Europe We declare under our sole responsibility that the product to which this declaration relates is in conformity with the standard or other normative document following the provisions of Directive 2004/108/EC. For U.S. and Canada: WV-TW310L, WV-TW310S For Europe and other countries: WV-TW310LE, WV-TW310SE For Canada This Class A digital apparatus complies with Canadian ICES-003. For U.S.A NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. FCC Caution: To assure continued compliance, (example - use only shielded interface cables when connecting to computer or peripheral devices). Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. Wir erklären in alleiniger Verantwortung, daß das Produkt, auf das sich diese Erklärung bezieht, mit der folgenden Norm oder normativen Dokument übereinstimmt. Gemäß den Bestimmungen der Richtlinie 2004/108/EC. Nous déclarons sous notre propre responsabilité que le produit auquel se réfère la présente déclaration est conforme á la norme spécifiée ou à tout autre document normatif conformément aux dispositions de la directive 2004/108/CE. Nosotros declaramos bajo nuestra única responsabilidad que el producto a que hace referencia esta declaración está conforme con la norma u otro documento normativo siguiendo las estipulaciones de la directiva 2004/108/CE. Noi dichiariamo sotto nostra esclusiva responsabilità che il prodotto a cui si riferisce la presente dichiarazione risulta conforme al seguente standard o altro documento normativo conforme alle disposizioni della direttiva 2004/108/CE. Wij verklaren als enige aansprakelijke, dat het product waarop deze verklaring betrekking heeft, voldoet aan de volgende norm of ander normatief dokument, overeenkomstig de bepalingen van Richtlijn 2004/108/ EC. Vi erklærer os eneansvarlige for, at dette produkt, som denne deklaration omhandler, er i overensstemmelse med standard eller andre normative dokumenter i følge bestemmelserne i direktiv 2004/108/EC. Vi deklarerar härmed vårt fulla ansvar för att den produkt till vilken denna deklaration hänvisar är i överensstämmelse med standarddokument eller annat normativt dokument som framställs i direktiv 2004/108/ EC. For U.S.A The model number and serial number of this product may be found on the surface of the unit. You should note the model number and serial number of this unit in the space provided and retain this book as a permanent record of your purchase to aid identification in the event of theft. Model No. Serial No. 2 Ilmoitamme yksinomaisella vastuullamme, että tuote, jota tämä ilmoitus koskee, noudattaa seuraavaa standardia tai muuta ohjeellista asiakirjaa, jotka noudattavat direktiivin 2004/108/EC säädöksiä. Vi erklærer oss alene ansvarlige for at produktet som denne erklæringen gjelder for, er i overensstemmelse med følgende norm eller andre normgivende dokumenter som følger bestemmelsene i direktiv 2004/108/EC. Contents Important safety instructions.......................................................................................................... 4 Limitation of liability........................................................................................................................ 4 Disclaimer of warranty.................................................................................................................... 5 Preface........................................................................................................................................... 5 Main functions................................................................................................................................ 6 About the user manuals................................................................................................................. 7 System requirements for a PC....................................................................................................... 8 Trademarks and registered trademarks......................................................................................... 9 Abbreviations.................................................................................................................................. 9 Copyright........................................................................................................................................ 9 Network security............................................................................................................................ 9 Precautions.................................................................................................................................. 10 Precautions for Installation........................................................................................................... 12 Major operating controls.............................................................................................................. 13 Insert/remove an SDHC memory card......................................................................................... 17 Installation.................................................................................................................................... 18 Connection................................................................................................................................... 23 Configure the network settings.................................................................................................... 24 Troubleshooting............................................................................................................................ 28 Specifications............................................................................................................................... 29 Standard accessories................................................................................................................... 31 Optional accessories.................................................................................................................... 31 3 Important safety instructions 1) Readtheseinstructions. 2) Keeptheseinstructions. 3) Heedallwarnings. 4) Followallinstructions. 5) Cleanonlywithdrycloth. 6) Donotinstallnearanyheatsourcessuchasradiators,heatregisters,stoves,orotherapparatus(includingamplifiers)thatproduceheat. 7) Onlyuseattachments/accessoriesspecifiedbythemanufacturer. 8) Referallservicingtoqualifiedservicepersonnel.Servicingisrequiredwhentheapparatushas been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture,doesnotoperatenormally,orhasbeendropped. Limitation of liability THIS PUBLICATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY,FITNESSFORANYPARTICULARPURPOSE,ORNON-INFRINGEMENTOF THETHIRDPARTY'SRIGHT. THIS PUBLICATION COULD INCLUDE TECHNICAL INACCURACIES OR TYPOGRAPHICAL ERRORS. CHANGES ARE ADDED TO THE INFORMATION HEREIN, AT ANY TIME, FOR THE IMPROVEMENTSOFTHISPUBLICATIONAND/ORTHECORRESPONDINGPRODUCT(S). 4 Disclaimer of warranty INNOEVENTSHALLPanasonicSystemNetworksCo.,Ltd.BELIABLETOANYPARTYORANY PERSON,EXCEPTFORREPLACEMENTORREASONABLEMAINTENANCEOFTHEPRODUCT, FORTHECASES,INCLUDINGBUTNOTLIMITEDTOBELOW: (1) ANY DAMAGE AND LOSS, INCLUDING WITHOUT LIMITATION, DIRECT OR INDIRECT, SPECIAL, CONSEQUENTIAL OR EXEMPLARY, ARISING OUT OF OR RELATING TO THE PRODUCT; (2) PERSONALINJURYORANYDAMAGECAUSEDBYINAPPROPRIATEUSEORNEGLIGENT OPERATIONOFTHEUSER; (3) ALL MALFUNCTIONS OR TROUBLES FROM UNAUTHORIZED DISASSEMBLE, REPAIR OR MODIFICATIONOFTHEPRODUCTBYTHEUSER,REGARDLESSOFTHECAUSEOFTHE MALFUNCTIONORTROUBLE; (4) INCONVENIENCE OR ANY LOSS ARISING WHEN IMAGES ARE NOT DISPLAYED, DUE TO ANYREASONORCAUSEINCLUDINGANYFAILUREORPROBLEMOFTHEPRODUCT; (5) ANY PROBLEM, CONSEQUENTIAL INCONVENIENCE, OR LOSS OR DAMAGE, ARISING OUTOFTHESYSTEMCOMBINEDBYTHEDEVICESOFTHIRDPARTY; (6) ANYCLAIMORACTIONFORDAMAGES,BROUGHTBYANYPERSONORORGANIZATION BEINGAPHOTOGENICSUBJECT,DUETOVIOLATIONOFPRIVACYWITHTHERESULTOF THAT SURVEILLANCE-CAMERA'S PICTURE, INCLUDING SAVED DATA, FOR SOME REASON,BECOMESPUBLICORISUSEDFORANYPURPOSE; (7) LOSSOFREGISTEREDDATACAUSEDBYANYFAILURE. Preface WV-TW310seriesWearableCamerasarebattery-poweredcamerasthatareusedtorecordimages bybeingwornonahumanbody.TheyhaveFisheyelens,whichenablesshootingwithsuperwide angles.ItisalsopossibletorecordH.264imagesontheSDHCmemorycardofthecamera. WV-TW310 • Imagecapturesize(1280x960(Aspectratioof4:3)). • Thereare2models,WV-TW310LandWV-TW310S,dependingonthelengthoftheconnecting cable. • WV-TW310seriesincludes2PCsoftwareapplications,WearableCameraAgentSoftwareand WearableCameraViewerSoftware,whichareintheprovidedCD-ROM. WV-TB311 (Optional) • TheWV-TB311isthebatterycontainerspecifiedfortheWV-TW310series. WV-TC312 (Optional) • TheWV-TC312istheconversionboxspecifiedfortheWV-TW310series. • TheWV-TC312isusedtoconnectthecameraandPC. • TheWV-TC312hasa12VDCinputterminaland10BASE-T/100BASE-TX(PoE)input terminal. 5 <System configuration> •NetworkCameraView4S •WearableCameraAgentSoftware •WearableCameraViewerSoftware PCinstalledwithsoftware Network(LAN) WearableCamera WearableCamera IMPORTANT: • Wearable Camera Agent Software uses directed broadcasts to search for the camera. The routerthatyouusemustbeconfiguredtoallowdirectedbroadcastpackets.Ifdirectedbroadcastpacketscannotbeconfiguredtobeallowed,structureyoursystemsothatcameraand thePCinstalledwithsoftwareareonthesamenetworksegment. • UseUDPport10668and10669fortransmissionsbetweentheWearableCameraAgentSoftware andthecamera.TherouterthatyouusemustbeconfiguredtoallowUDPport10668and10669. Note: • ItisnecessarytoconfigurethenetworksettingsofthePCanditsnetworkenvironmenttomonitorimagesfromthecameraonthePC.ItisalsonecessarytoinstallawebbrowseronthePC. Main functions H.264 Recording ImagesareencodedtoH.264andsavedontheSDHCmemorycard. Wide angle Thewideanglelensenableswideareastoberecorded. Pre recording Dependingonthesettings,prerecordingofupto30secondsispossible. Color mode / black & white mode switching available Imageswillbedisplayedclearlyevenatnightsincethecamerawillbeautomaticallyswitchedfrom thecolormodetotheblackandwhitemodeunderlowilluminationcondition. Power over Ethernet function WhenconnectingwithaPoE(PoweroverEthernet)device,powerwillbesuppliedbysimplyconnectingaLANcable.(IEEE802.3afcompliant) 6 Upload and save the video image data WithWearableCameraAgentSoftware(includedintheCD-ROM),youcanuploadthevideoimage datafromthecameratoaPCandsaveit. Combine the multiple video image data With Wearable Camera Agent Software (included in the CD-ROM), you can combine the multiple videoimagedatainMPEG4fileformat. Verifying (Integrity check) With Wearable Camera Agent Software or Wearable Camera Viewer Software (included in the CD-ROM),youcanverifythevideoimagedata. Image correction WithWearableCameraViewerSoftware(includedintheCD-ROM),youcanviewtheimageswith stabilizationanddistortioncorrection. Playback WithWearableCameraViewerSoftware(includedintheCD-ROM),youcanplayvideoimages. Snapshot WithWearableCameraViewerSoftware(includedintheCD-ROM),youcantakesnapshots. About the user manuals Thereare2setsofoperatinginstructionsfortheWV-TW310L,WV-TW310S(Pmodel),WV-TW310LE andWV-TW310SE(Emodel). • InstallationGuide:Explainshowtoinstallandconnectdevices. • Operating Instructions (included in the CD-ROM): Explains how to perform the settings and howtooperatethiscamera. Adobe®Reader®isrequiredtoreadtheseoperatinginstructionsontheprovidedCD-ROM. When the Adobe Reader is not installed on the PC, download the latest Adobe Reader from the Adobewebsiteandinstallit. Themodelnumberisabbreviatedinsomedescriptionsinthismanual. ThescreensorillustrationsusedinthismanualshowthecaseofWV-TW310L(Pmodel). 7 System requirements for a PC CPU: Memory: NetworkInterface: Audiointerface: Monitor: OS: WebBrowser: Other: Intel®CoreTM2Duo2.66GHzorfasterrecommended 2GBormore 10BASE-T/100BASE-TX1port Soundcard(whenusingtheaudiofunction) Imagecapturesize:1024x768pixelsormore Color:24-bitTruecolororbetter Microsoft®Windows®7 Microsoft®WindowsVista® Microsoft®Windows®XPSP3 Windows®InternetExplorer®9.0(32-bit) Windows®InternetExplorer®8.0(32-bit) Windows®InternetExplorer®7.0(32-bit) Microsoft®InternetExplorer®6.0SP3 CD-ROMdrive (Itisnecessarytoreadtheoperatinginstructionsandusethesoftwareon theprovidedCD-ROM.) DirectX®9.0corlater Adobe®Reader® (ItisnecessarytoviewthePDFfileontheprovidedCD-ROM.) IMPORTANT: • When using a PC that does not meet the above requirements, displaying of images may becomeslowerorthewebbrowsermaybecomeinoperable. • Audio may not be heard if a sound card is not installed on a PC. Audio may be interrupted dependingonthenetworkenvironment. • Microsoft Windows 7 Starter, Microsoft Windows Vista Starter and Microsoft Windows XP Professional64-bitEditionarenotsupported. • WhenusingIPv6forcommunication,useMicrosoftWindows7orMicrosoftWindowsVista. Note: • Refer to "Notes on Windows®/ Internet Explorer® versions" (included in the CD-ROM) for further information about system requirements for a PC and precautions when using MicrosoftWindows7,MicrosoftWindowsVistaorInternetExplorer. 8 Trademarks and registered trademarks • Microsoft, Windows, Windows Vista, Internet Explorer, ActiveX, and DirectX are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. • Microsoftproductscreenshot(s)reprintedwithpermissionfromMicrosoftCorporation. • IntelandIntelCorearetrademarksorregisteredtrademarksofIntelCorporationintheUnited Statesandothercountries. • Adobe,AcrobatReader,andReaderareeitherregisteredtrademarksortrademarksofAdobe SystemsIncorporatedintheUnitedStatesand/orothercountries. • Allothertrademarksidentifiedhereinarethepropertyoftheirrespectiveowners. Abbreviations TheWearableCameraisrefertoas"thecamera"inthismanual. Copyright Distributing, copying, disassembling, reverse compiling and reverse engineering of the software providedwiththisproductareallexpresslyprohibited.Inaddition,exportinganysoftwareprovided withthisproductviolatingexportlawsisprohibited. Network security Asyouwillusethisunitconnectedtoanetwork,yourattentioniscalledtothefollowingsecurity risks. q Leakageortheftofinformationthroughthisunit w Useofthisunitforillegaloperationsbypersonswithmaliciousintent e Interferencewithorstoppageofthisunitbypersonswithmaliciousintent It is your responsibility to take precautions such as those described below to protect yourself againsttheabovenetworksecurityrisks. • Usethisunitinanetworksecuredbyafirewall,etc. • IfthisunitisconnectedtoanetworkthatincludesPCs,makesurethatthesystemisnotinfected by computer viruses or other malicious entities (using a regularly updated anti-virus program,anti-spywareprogram,etc.). • Protectyournetworkagainstunauthorizedaccessbyrestrictinguserstothosewhologinwith anauthorizedusernameandpassword. • Applymeasuressuchasuserauthenticationtoprotectyournetworkagainstleakageortheftof information,includingimagedata,authenticationinformation(usernamesandpasswords). • Aftertheunitisaccessedbytheadministrator,makesuretoclosethebrowser. • Changetheadministratorpasswordperiodically. • Do not install the camera in locations where the camera or the cables can be destroyed or damagedbypersonswithmaliciousintent. 9 Precautions Follow the instructions of battery. Use only the WV-TB311 battery container (optional) for the battery. In combination with this product, refer to the WV-TB311 and WV-TC312OperatingInstructionsforcareand handlingofthebatterycharge. Stop the operation immediately when something is wrong with this product. When smoke goes up from this product or the smell of smoke comes from this product, stop the operation immediately and contact your dealer. Turn the power off immediately and contact qualifiedservicepersonnelforservice. Do not attempt to disassemble or modify this product. Failuretoobservethismaycausefireorelectric shock. Consultthedealerfortherepairorinspections. Do not insert any foreign objects. Thiscouldpermanentlydamagetheapparatus. Turn the power off immediately and contact qualifiedservicepersonnelforservice. Do not use this product in an inflammable atmosphere. Failuretoobservethismaycauseanexplosion resultingininjury. Do not install this product in locations subject to vibration. Loosening of mounting screws or bolts may causeafalloftheproductresultingininjury. Do not strike or give a strong shock to this product. Failuretoobservethismaycausefireorinjury. Do not rub the edges of metal parts with your hand. Failuretoobservethismaycauseinjury. Turn the power off when connecting this product. Failuretoobservethismaycauseelectricshock. Inaddition,shortcircuitmaycausefire. 10 Do not directly touch the product with your skin when it has been turned on for an extended period. Directskincontactwithhigh-temperatureparts oftheproductforextendedperiodsmaycause low-temperatureburns. Turn the power off when cleaning of this product. Failuretoobservethismaycauseinjury. [Precautions for use] To keep on using with stable performance Donotusethiscamerainhotandhumidconditions for a long time. Failure to observe this causescomponentdegradationresultinginlife shorteningofthisproduct. Do not expose this camera to direct heat sourcessuchasaheater. Handle this camera with care. Do not drop this camera, nor apply shock or vibrationtothiscamera.Failuretoobservethis maycausetrouble. About the PC monitor Displaying the same image on a CRT type monitorforalongtimemaydamagethemonitor.Itisrecommendedtouseascreen-saver. When an error is detected, this product will restart automatically. This product will be inoperable for about 2 minutes after the restart just as when the poweristurnedon. Product disposal/transfer Datasavedonthisproductorastoragedevice used with this product may lead to personal informationleakage. When it is necessary to dispose or give this product to someone, even when for repair, makesurethatthereisnodataonthisproduct. Cleaning this product body Be sure to turn off the power before cleaning. Do not use strong abrasive detergent when cleaning this camera. Otherwise, it may cause discoloration. Whenusingachemicalclothforcleaning,readthe cautionprovidedwiththechemicalclothproduct. Do not touch the lens cover with your bare hands. A dirty lens cover causes deterioration of picturequality. Cleaning the lens cover Usealenscleaningpaper(usedtocleancamera lenses or lenses of spectacles). When using solvent, use an alcohols solvent and do notuseathinneroraglasscleaner. Transmission interval Image transmission interval may become slow dependingonthenetworkenvironment,PCperformance,shootingsubject,accessnumber,etc. About SDHC memory card • BeforeinsertingtheSDHCmemorycard,turn offthepowerofthisproductfirst.Otherwise, it may cause malfunction or damage data recordedontheSDHCmemorycard. • WhenusinganunformattedSDHCmemory card, format it using this camera. RecordeddataontheSDHCmemorycard willbedeletedwhenformatted.Ifanunformatted SDHC memory card or an SDHC memorycardformattedwithotherdevices isused,thisproductmaynotworkproperly or performance deterioration may be caused.RefertotheOperatingInstructions (included in the CD-ROM) for how to formatanSDHCmemorycard. • WhensomeSDHCmemorycardsareused with this product, the product may not workproperlyorperformancedeterioration may be caused. Use the SDHC memory cardsrecommendedinpage30. • FrequentlyoverwritingtheSDmemorycard reduces its product life. It is recommended toreplacetheSDmemorycardonceayear. Contact service personnel for information aboutreplacementSDmemorycards. About the MOS image sensor • When continuously shooting a bright light source such as a spotlight, the color filter oftheMOSimagesensormayhavedeteriorated and it may cause discoloration. Even when changing the fixed shooting direction after continuously shooting a spotlightforacertainperiod,thediscolorationmayremain. • Whenshootingfast-movingsubjects, objects crossing the shooting area may look to be bendingaskew. AVC Patent Portfolio License THIS PRODUCT IS LICENSED UNDER THE AVCPATENTPORTFOLIOLICENSEFORTHE PERSONAL USE OF A CONSUMER OR OTHER USES IN WHICH IT DOES NOT RECEIVE REMUNERATION TO (i) ENCODE VIDEO IN COMPLIANCE WITH THE AVC STANDARD ("AVC VIDEO") AND/OR (ii) DECODE AVC VIDEO THAT WAS ENCODED BYACONSUMERENGAGEDINAPERSONAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED TO PROVIDE AVC VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE. ADDITIONAL INFORMATION MAY BE OBTAINEDFROMMPEGLA,L.L.C. SEEHTTP://WWW.MPEGLA.COM About the stabilization Excessively rough movements during recording reducestheeffectivenessofdistortioncorrection. About the batteries The capacity of the battery is reduced each timeitisused.Inparticular,rechargingorusing the battery in high-temperature locations increasesdeterioration. 11 Precautions for Installation Panasonic assumes no responsibility for injuries or property damage resulting from failures arising out of improper installation or operation inconsistent with this documentation. Installation place Donotplacetheunitinthefollowingplaces: • Locationswhereachemicalagentisused suchasaswimmingpool • Locationssubjecttohumidity,dust,steam andoilsmoke • Locations in a specific environment where a solvent or a flammable atmosphere exists • Locations where a radiation, an X-ray, a strong radio wave or a strong magnetic fieldisgenerated • Locations where corrosive gas is produced, Locations where it may be damagedbybrinyairsuchasseashores • Locations where the temperature is not within–10°Cto+50°C{14°Fto122°F}. • Locationssubjecttovibrations(Thisproductisnotdesignedforon-vehicleuse.) IMPORTANT: • When attaching the camera to your body, useitenvironmentswithambienttemperaturesof-10°Cto+45°C{14°Fto113°F}. Note: • Locations subject to condensation as the resultofseverechangesintemperature Shielded (STP) LAN cables must be used with this unit to ensure compliance with EMC standards. * *Emodelsonly Radio disturbance WhenthisproductisusednearTV/radioantenna,strongelectricfieldormagneticfield(neara motor, a transformer or a power line), images maybedistortedandnoisesoundmaybeproduced. 12 PoE (Power over Ethernet) Use a PoE hub/device that is compliant with IEEE802.3afstandard. Time & date setting It is necessary to set the time & date before putting this product into operation. Because thetime&dateofthisproductissettothetime and date of the connected computer, make sure that the time and date settings of the computer are correct before connecting the camera. Major operating controls <Camera> WV-TW310 Connecting cable Lens cover Connector Clip Mic hole SDHC memory card slot Initial set button REC button (Recording start button) About the initial set button After turning off the power of the camera, while recharging the battery, turn on the power of the camerawhileholdingdownthisbutton,andwaitforabout5secondsormorewithoutreleasingthis button.Waitabout3minutesafterreleasingthebutton.Thecamerawillstartupandthesettings includingthenetworksettingswillbeinitialized.Beforeinitializingthesettings,itisrecommendedto writedownthesettingsinadvance. 13 <Battery container (Optional)> WV-TB311 (Optional) Indicatorlamps <Rear view> Clip Connector Powerbutton The connector cover of the battery container (optional) can be opened in the following way and fixedtothesideofthebatterycontainer(optional).Whenstoringthebatterycontainer(optional)in thestand,opentheconnectorcoverandfixittothesideofthebatterycontainer(optional). Connectorcover Connectorcover Network/chargeconnector About the battery container's indicators Thebatterycontainer'sindicatorslightasfollowsaccordingtothestatusofthecamera.Understanding howandwhentheindicatorslightcanhelpyoutroubleshootproblemswiththecamera. Indicator Slowblinking Lightoff PowerOFF (Remainingbatterytime:None) REC Recordingimag- Recording esandaudio images qWritingrecordeddata Notrecording wAccessingtheSDmemorycard Pre-recording RemainingSD recordingtime: Long RemainingSD recordingtime: Short SDmemorycarderror ∙TheSDmemorycardisnotinserted ∙TheSDmemorycardislocked ∙Thereisnoremainingmemory ∙Aread/writeerrorhasoccurred - - CHG Green:Charging Red:Charging errordetected ON (Remainingbatterytime:Short) Fastblinking PWR SD 14 Lit ON (Remainingbatterytime:Long) Activating - Operating normally <Conversion box (Optional)> WV-TC312 (Optional) Conversionbox(optional) Network/chargecable Powerindicator Networkconnector Terminals of the 12 V DC IN connector (Pinout) 1 12VDCINconnector 2 3 4 PinNo. 1 2 3 4 + NC NC 15 Thebatterycontainer(optional)andthecameracanbestoredinthestandmountedtotheconversion box (optional). With the battery container (optional) and the camera stored in the stand, the conversionbox(optional)canbeconnectedto12VDCoraPoEhub,makingrechargingthebattery container (optional) possible, a LAN cable can also be connected to the conversion box (optional),makingitpossibletoviewsavedimagesonacomputermonitor. Whenremovingthestandfromtheconversionbox(optional),liftupthestandwhilepressingthe4 tabsonthestandatthesametime. Tab Stand Tab Conversionbox(optional) 16 Insert/remove an SDHC memory card IMPORTANT: • ContactanauthorizedservicecenterforinformationonreplacingSDHCmemorycards. • BeforeinsertinganSDHCmemorycard,turnoffthepowerofthecamerafirst. • WheninsertinganSDHCmemorycard,makesurethedirection. • When the SDHC memory card is inserted or removed with the power on, data in the SDHC memorycardmaybedamaged. • Donotuseotherscrewstotightenthecover. RecommendedtighteningtorqueT8:0.2N·m{0.14lbf·ft} z Remove the memory cover after removing the tamperproof screw of the cover on the WV-TW310,andinserttheSDHCmemorycardintotheSDHCmemorycardslot. x Attachthecover,andtightenthetamperproofscrew. Recommendedtighteningtorque:T8:0.2N·m{0.14lbf·ft} 17 Installation Connecting the battery container (optional) to the camera z Align the direction of the mark on the connector on the end of the connecting cable to the directionofthemarkonthebatterycontainer(optional). x Inserttheconnectoroftheconnectingcablestraightintotheconnectorofthebatterycontainer (optional),andthenlockitbyrotatingtheouterringoftheconnectingcableclockwise. Batterycontainer(optional) Connector Outerring Rotateclockwise. Removing the battery container (optional) from the camera Toremovethecamerafromthebatterycontainer(optional),unlocktheconnectorbyrotating theouterringcounterclockwise,andthenpulltheconnectingcablestraight. Rotatecounterclockwise. 18 Connecting the conversion box (optional) to the battery container (optional) z Connectthepowertotheconversionbox(optional). Connect12VDCorPoEhubforthepowersource. Connectingcable Stand Camera Conversionbox (optional) Networkconnector 12VDCINconnector LANcable x Connectthenetwork/chargecableoftheconversionbox(optional)tothenetwork/chargecon nectorofthebatterycontainer(optional). Insertthecableintotheconnectoruntilaclickisheard.Ensurethattheyareconnectedinthe correctdirection. Batterycontainer(optional) Network/chargeconnector Network/chargecable 19 c Connecttheconnectingcableofthecameratotheconnectorofthebatterycontainer(optional). Thenchargingstarts. Connectingcable Batterycontainer(optional) Camera LANcable IMPORTANT: • Rechargingwillnotbeginifthetemperatureoftheinternalbatterypackisoutsideoftheallowabletemperaturerange(0°Cto+50°C{32°Fto122°F}). • Chargingbeginsautomaticallywhenthetemperatureenterstheallowablerange. • Rechargingwillstopafter6hoursfromwhentheconnectionwasmade. (Undernormalconditions,rechargingfinisheswithin3.5hours.) • Exposing the battery to high temperatures may cause battery deterioration (reduced battery capacityandrechargingcycle). Note: • WhenthecameraisconnectedtoaPoEhubwithoutthebatterycontainer(optional)connected, thepowerindicatoroftheconversionbox(optional)mayblink.Thisisnotamalfunction. 20 Wearing the camera z Attachthebatterycontainer(optional)tothebeltyouarewearing. Belt Battery container (optional) x Thecameraclipcanbeattachedin4directionstothecameradependingonwhereyouwant tofixthecamera.Thecameraclipcanbefixedtoclothing(belts,pockets,etc.)fromdifferent directions(top,bottom,left,orright)bychangingthedirectionitisattachedtothecamera. Tochangethedirectionofthecameraclip,loosenthecameraclipscrews,rotatethecliptothe desireddirection,andthenretightenthecameraclipscrews. Recommendedtighteningtorque:0.78N·m{0.58lbf·ft}. Fixingscrewforclip 21 c Fixthecameratoyourclothing. <WV-TW310L> <Frontview> <Rearview> Connectingcable Camera Batterycontainer(optional) <Lens angular field of view> <WV-TW310S> Camera 140° 180° IMPORTANT: • Attachthecamerasothatitissecurelyfixed. • Attachingthecameratolooseclothingreducestheeffectivenessofdistortioncorrection. 22 Connection Caution: • ONLYCONNECT12VDCCLASS2POWERSUPPLYorLIMITEDPOWERSOURCE. Beforestartingtheconnection,turnoffthepowerforthiscameraandthedevicestobeconnected, andthenpreparetherequireddevicesandcables. Connection example when connecting to a network using a PoE hub PoE Hub Charge 5 V DC LAN Data Communication PC LAN cable (category 5 or better, straight, STP*) PC <Required cable> LANcable(category5orbetter,straight,STP*) *Emodelsonly IMPORTANT: • Useaswitchinghuborarouterwhichiscompliantwith10BASE-T/100BASE-TX. • Power supply is required for each camera. When using a PoE device (hub), 12 V DC power supplyisunnecessary. 23 Configure the network settings Install the software Beforeinstallingthesoftware,readthereadmefileontheprovidedCD-ROMfirst. Software included on the provided CD-ROM • PanasonicIPsettingsoftware Configurethenetworksettingsofthecamera.Refertothefollowingforfurtherinformation. • ViewerSoftware"NetworkCameraView4S" Itisnecessarytoinstalltheviewersoftware"NetworkCameraView4S"todisplayimagesona PCandtosetuptheWearableCamerabasicconfiguration.Installtheviewersoftwarebydouble-clicking the "nwcv4Ssetup.exe" icon on the provided CD-ROM. Refer to the WV-TW310 OperatingInstructions(includedintheCD-ROM)formoredetails. • WearableCameraAgentSoftware ItisnecessarytoinstalltheWearableCameraAgentSoftwaretouploadthevideoimagedata fromthecameras. • WearableCameraViewerSoftware ItisnecessarytoinstalltheWearableCameraViewerSoftwaretoplaythevideoimagedata. Configure the network settings of the camera using the Panasonic IP setting software It is possible to perform the network settings of the camera using the IP setup software on the provided CD-ROM. When using multiple cameras, it is necessary to configure the network settings of each camera independently. If the Panasonic IP setting software does not work, configure the network settings of the camera and the PC individually on the "Network" page of the setup menu. Refer to the Operating Instructions (included in the CD-ROM) for further information. IMPORTANT: • When using Microsoft Windows 7 or Microsoft Windows Vista, the "Windows Security Alert" window may be displayed when starting the IP setup software. In this case, disable "User Account Control" from the control panel. • For the security enhancement, the MAC address/IP address of the camera to be configured will not be displayed when about 20 minutes have passed after turning on the power of the camera. (When the effective period is set to "20min" in the IP setup) However cameras in the initial set mode are still displayed even after 20 minutes. • Panasonic IP setting software is inoperable in other subnets via the same router. When configuring the IP address of the camera for the first time, configure the PC's IP address to 192.168.0.xxx. • This camera cannot be displayed or set with an older version of the IP setup software (version 2.xx). z Start the Panasonic IP setting software by double-clicking the "EasyIpSetup.exe" icon on the provided CD-ROM. • The License Agreement will be displayed. Read the Agreement and choose "I accept the term in the license agreement", and click [OK]. x Click the [Network Settings] button after selecting the MAC address/IP address of the camera to be configured. 24 Note: • When using a DHCP server, the IP address assigned to the camera can be displayed by clicking the [Search] button of the IP setting software. • When a duplicate IP address is used, the corresponding camera number will be displayed shaded. • When the [Access Camera] button is clicked, live images of the selected camera will be displayed. • It is possible to change the "Camera list" display between IPv4 addresses and IPv6 addresses in accordance with the protocol in use. • The information displayed can be sorted by clicking the title of each displayed item. c Complete each network setup item and click the [Save] button. Note: • In the camera settings, "Auto IP" is deactivated even when it is selected for the connection mode. • In the camera settings, the "Primary DNS" and "Secondary DNS" settings are deactivated. IMPORTANT: • It may take for about 2 minutes to complete to upload the settings to the camera after clicking the [Save] button. The settings may be invalidated when the LAN cable is disconnected before completing the upload. In this case, perform the settings again. • When using a firewall (including software), allow access to all UDP ports. • The Wearable Camera Agent Software and Panasonic IP setting software cannot be used on the same PC at the same time. To use the Panasonic IP setting software on a PC with Wearable Camera Agent Software installed: right click "My Computer" and select "Manage" to open the "Computer Management" screen, select and right click "Wearable Camera Agent" from [Services and Applications] - [Services], and then select "Stop". After finishing using the Panasonic IP setting software, perform the above steps again, select and right click "Wearable Camera Agent", and then select "Start". 25 Installation of Wearable Camera Agent Software z InserttheprovidedCD-ROMintotheCD-ROMdriveofyourPC. x Double-click"Agent_setup.exe"inthe"PC_software"folder.TheinstallerforWearableCamera AgentSoftwarewillstart.Followtheon-screeninstructions.Iftheinstallationisperformedwith the standard settings, a "C:\Panasonic\Wearable" folder is created and executable files and otherfilesareinstalled. c ConfiguretheexceptionalsettingsofWindowsFirewall. ProceduresforWindowsXP qClickthe"SecurityCenter"onthe"ControlPanel",andclick"WindowsFirewall" "Exceptions"tab. wClickthe"AddProgram..."button,andclickthe"Browse..."button. eSelect"CamManageService.exe"inthefolder"C:\Panasonic\Wearable\Agent",andclick the"Open"button. rSelect"CamManageService.exe",andclickthe"OK"button. tPerformstepswtorinthesamemannertoadd"AgentGui.exe". ProceduresforWindowsVista qOpenthe"Security"onthe"ControlPanel",andclickthe"WindowsFirewall""AllowAProgramThroughWindowsFirewall"-"Exceptions"tab. wClickthe"AddProgram..."button,andclickthe"Browse..."button. eSelect"CamManageService.exe"inthefolder"C:\Panasonic\Wearable\Agent",andclick the"Open"button. rSelect"CamManageService.exe",andclickthe"OK"button. tPerformstepswtorinthesamemannertoadd"AgentGui.exe". ProceduresforWindows7 qOpenthe"SystemandSecurity"onthe"ControlPanel",andclickthe"Windows Firewall"-"AllowAProgramThroughWindowsFirewall". wClickthe"AllowAnotherProgram"button,andclickthe"Browse..."button. eSelect "CamManageService.exe" in the folder "C:\Panasonic\Wearable\Agent", and click the"Open"button. rSelect"CamManageService.exe",andclickthe"OK"button. tPerformstepswtorinthesamemannertoadd"AgentGui.exe". Uninstallation of Wearable Camera Agent Software Note: • The data uploaded from the camera will not be deleted even when this software is uninstalled. ProceduresforWindowsXP qSelect"WearableCameraAgent"from[ControlPanel]-[AddorRemovePrograms]. wClick[Delete].Theuninstallprogramstarts.Followtheon-screeninstructionstouninstalltheprogram. 26 Procedures for Windows Vista q Select "Wearable Camera Agent" from [Control Panel]-[Programs]-[Uninstall a program]. w Click [Uninstall]. The uninstall program starts. Follow the on-screen instructions to uninstall the program. Procedures for Windows 7 q Open "Programs and Features" from [Control Panel]-[Programs]. w Select "Wearable Camera Agent" from the presently installed programs and click the [Remove] button. e Uninstall the software by following the instructions displayed on the monitor. How to operate the Wearable Camera Agent Software Refer to the WV-TW310-Agent_en.chm file for the details. Installation of Wearable Camera Viewer Software z Insert the provided CD-ROM into the CD-ROM drive of your PC. x Double-click "Viewer_setup.exe" in the "PC_software" folder. The installer for Wearable Camera Viewer Software will start. Follow the on-screen instructions. If the installation is performed with the standard settings, a "C:\Panasonic\Wearable" folder is created and executable files and other files are installed. Uninstallation of Wearable Camera Viewer Software Procedures for Windows XP q Select "Wearable Camera Viewer" from [Control Panel]-[Add or Remove Programs]. w Click [Delete]. The uninstall program starts. Follow the on-screen instructions to uninstall the program. Procedures for Windows Vista q Select "Wearable Camera Viewer" from [Control Panel]-[Programs]-[Uninstall a program]. w Click [Uninstall]. The uninstall program starts. Follow the on-screen instructions to uninstall the program. Procedures for Windows 7 q Open "Programs and Features" from [Control Panel]-[Programs]. w Select "Wearable Camera Viewer" from the presently installed programs and click the [Remove] button. e Uninstall the software by following the instructions displayed on the monitor. How to operate the Wearable Camera Viewer Software Refer to the WV-TW310-Viewer_en.chm file for the details. 27 Troubleshooting Before asking for repairs, check the symptoms with the following table. Contactyourdealerifaproblemcannotbesolvedevenaftercheckingandtryingthesolutioninthe tableoraproblemisnotdescribedbelow. Symptom Power is not turned on. Camera search cannot be performed with Panasonic "IP Setting Software". 28 Cause/solution Reference pages When using DC power supply •Is12VDCpowersupplyconnectedto thepowersupplyterminal? →Checkwhethertheconnectionis appropriatelyestablished. •IstheACadaptorinusecompliantwith theSpecifications? →ChecktheSpecificationsregarding ACadaptor. When using a PoE device for power supply •ArethePoEdeviceandthenetwork connectorontherearofthecamera connectedusingaLANcable(4-pair)? →Checkwhethertheconnectionis appropriatelyestablished. •DependingonthePoEdevice,the powersupplywillstopwhenthe demandedpowerexceedsitstotal powerlimitforallPoEports. →Refertotheoperatinginstructionsof thePoEdeviceinuse. 23 Click"ServicesandApplications",select "WearableCameraAgent"under "Services",andthenrightclickandselect "Stop".AfterusingPanasonic"IPSetting Software",followtheaboveprocedureto select"WearableCameraAgent",and thenrightclickandtheselect"Start". 24 Specifications ● Basic Powersource: Powerconsumption: Ambientoperating temperature: Ambientoperatinghumidity: Continuousoperatingtime: Battery: Dimensions: Mass: CableLength: Finish: 12VDC,PoE(IEEE802.3afcompliant) 12VDC*:650mA,PoE:11W(Class0device) *ONLYCONNECT12VDCCLASS2POWERSUPPLYor LIMITEDPOWERSOURCE. –10°Cto+50°C{14°Fto122°F} Inwearing:-10°Cto+45°C{14°Fto113°F} Lessthan90%(nocondensation) Approx.5hours (atnormaltemperature,atthetimeofpurchasewhenchargedfully) WV-TB311(Lithium-ionbattery)only 45mm(W)x75mm(H)x41mm(D) {1-25/32inches(W)x2-15/16inches(H)x1-5/8inches(D)} (Excludingthecableandprojection.) WV-TW310L:Approx.210g{0.46lbs.} WV-TW310S:Approx.160g{0.35lbs.} WV-TW310L:950mm{37-3/8inches} WV-TW310S:600mm{23-5/8inches} Black ● Camera Imagesensor: Effectivepixels: Scanningarea: Scanningsystem: Minimumillumination: Gain(AGC): Widedynamicrange: Adaptiveblackstretch: Backlightcompensation: Lightcontrolmodesetting: Maximumexposuretime: Day&Night(electrical): Whitebalance: Digitalnoisereduction: 1/4typeMOSimagesensor Approx.1.3megapixels 3.60mm(H)x2.70mm(V){5/32inches(H)x11/100inches(V)} Progressive Color: 1.5lx{1.5footcandle} BW: 1.0lx{1.0footcandle} On(High)/On(Mid)/On(Low)/Off On/Off On/Off On/Off Indoorscene(50Hz/60Hz)/ELC 1/30,3/100,3/120,2/100,2/120,1/100,1/120,1/250, 1/500,1/1000,1/2000,1/4000,1/10000 Off/Auto ATW1/ATW2/AWC High/Low ● Lens Focallength: Maximumapertureratio: Angularfieldofview: 0.82mm 1:2.6 Horizontal:180° Vertical:140° 29 ● Network Network: Resolution: Imagecompressionmethod: Audiocompressionmethod: Protocol: OS*1*2: Browser: Maximumconcurrentaccess number: CompatibleSDHCmemory card(option): 10BASE-T/100BASE-TX,RJ45connector Aspectratio:4:3 H.2641280×960 JPEG640×480(OnlyHTMLonPC,5fps) H.264Transmissiontype:Unicast Videobitrate: 2048kbps/4096kbps/8192kbps Frameratepriority:15fps/30fps G.726(ADPCM)32kbps IPv6:HTTP,FTP IPv4:HTTP,FTP,DHCP MicrosoftWindows7 MicrosoftWindowsVista MicrosoftWindowsXPSP3 WindowsInternetExplorer9.0(32-bit) WindowsInternetExplorer8.0(32-bit) WindowsInternetExplorer7.0(32-bit) MicrosoftInternetExplorer6.0SP3 10atJPEG,4atH.264 ManufacturedbyPanasonic SDHCmemorycard:32GB,Class10 *1 Referto"NotesonWindows®/InternetExplorer®versions"(includedintheCD-ROM)forfurther information about system requirements for a PC and precautions when using Microsoft Windows7,MicrosoftWindowsVistaorInternetExplorer. *2 WhenusingIPv6forcommunication,useMicrosoftWindows7orMicrosoftWindowsVista. 30 Standard accessories InstallationGuide(thisdocument)..................................................................................1pc. Warrantycard*1..............................................................................................................1pc. CD-ROM*2....................................................................................................................1pc. *1Pmodelsonly *2TheCD-ROMcontainstheoperatinginstructionsandthesoftware. Optional accessories BatteryContainer(Li-ion3.7VDC,2450mAh,9.1Wh)..........WV-TB311 ConversionBox.......................................................................WV-TC312 UserLicenseAccessory(ForH.264)........................................BB-HCA8A(Pmodel) BB-HCA8CE(Emodel,Korea) 31 Information for Users on Collection and Disposal of Old Equipment and used Batteries These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries should not be mixed with general household waste. For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable collection points, in accordance with your national legislation and the Directives 2002/96/EC and 2006/66/EC. By disposing of these products and batteries correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling. For more information about collection and recycling of old products and batteries, please contact your local municipality, your waste disposal service or the point of sale where you purchased the items. Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation. For business users in the European Union If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information. [Information on Disposal in other Countries outside the European Union] These symbols are only valid in the European Union. If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of disposal. Cd Note for the battery symbol (bottom two symbol examples): This symbol might be used in combination with a chemical symbol. In this case it complies with the requirement set by the Directive for the chemical involved. For U.S. and Canada: For Europe and other countries: Panasonic System Communications Company of North America, Unit of Panasonic Corporation of North America Panasonic Corporation www.panasonic.com/business/ For customer support, call 1.800.528.6747 Three Panasonic Way, Secaucus, New Jersey 07094 U.S.A. http://panasonic.net Importer's name and address to follow EU rules: Panasonic Testing Centre Panasonic Marketing Europe GmbH Winsbergring 15, 22525 Hamburg F.R.Germany Panasonic Canada Inc. 5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 Canada (905)624-5010 www.panasonic.ca ©PanasonicSystemNetworksCo.,Ltd.2012 Cs0212-3042PGQX1132WAPrintedinChina