Download Aiwa NSX-DS50 Service manual

NSX-DS50
NSX-DS55
U
U
SERVICE MANUAL
COMPACT DISC
STEREO SYSTEM
BASIC TAPE MECHANISM : ZZM-3 PR3NM
BASIC CD MECHANISM : BZG-5 ZD3NM
SYSTEM
CD
CASSEIVER
NSX-DS50
CX-NDS50
NSX-DS55
CX-NDS55
SPEAKER
REMOTE
CONTROLLER
SX-NAJ502
SX-R290
SX-C610
RC-BAS10 VS
• This Service Manual is the “Revision Publishing” and replaces
“Simple Manual” of NSX-DS50 / DS55 <U>, (S/M Code No. 09-014-445-3T1).
S/M Code No. 09-017-445-3R1
RE
VI
SIO
DA
N
TA
• If requiring information about the CD mechanism, see Service Manual of
BZG-5, (S/M Code No. 09-00C-353-3N2).
SPECIFICATIONS
MAIN UNIT CX-NDS50 / CX-NDS55
TUNER
FM tuning range
FM usable sensitivity (IHF)
FM antenna terminals
AM tuning range
AM usable sensitivity
AM antenna
AMPLIFIER
Power output
Total harmonic distortion
Inputs
Outputs
CASSETTE DECK
Track format
Frequency response
Recording system
Heads
CD PLAYER
Laser
D/A converter
Signal-to-noise ratio
Harmonic distortion
87.5 MHz to 108 MHz
13.2 dBf
75 ohms (unbalanced)
530 kHz to 1710 kHz (10 kHz step)
531 kHz to 1602 kHz (9 kHz step)
350 µV/m
Loop antenna
Front:
70 W + 70 W (50 Hz - 20 kHz,
THD less than 1 %, 6 ohms)
88 W + 88 W (1 kHz,
THD less than 10 %, 6 ohms)
Rear (Surround):
25 W + 25 W (1 kHz,
THD less than 1 %, 8 ohms)
35 W + 35 W (1 kHz,
THD less than 10 %, 8 ohms)
Center:
25 (1 kHz, THD less than 1 %, 8 ohms)
35 W (1 kHz, THD less than 10 %,
8 ohms)
0.1 % (35 W, 1 kHz, 6 ohms,
DIN AUDIO/Front)
VIDEO/AUX/DVD: 300 mV (adjustable)
DIGITAL IN (PCM/DOLBY DIGITAL)
OPTICAL (VIDEO/AUX/DVD): Linear
PCM signals (32 kHz, 44.1 kHz and
48 kHz) and Dolby Digital bitstream
FRONT SPEAKERS: 6 ohms or more
SURROUND SPEAKERS: 8 ohms to
16 ohms
CENTER SPEAKER: 8 ohms or more
SUB WOOFER: 1 V
PHONES: 32 ohms or more
4 tracks, 2 channels stereo
50 Hz - 15 kHz
AC bias
Deck 1: playback x 1
Deck 2: recording/playback x 1,
erase x 1
Semiconductor laser (λ = 780 nm)
1 bit dual
85 dB (1 kHz, 0 dB)
0.05 % (1 kHz, 0 dB)
GENERAL
Power requirements
Power consumption
Power consumption
in standby mode
Dimensions (W x H x D)
Weight of main unit
120 V AC, 60 Hz
175 W
With ECO mode on: 0.6 W
With ECO mode off: 35 W
260 x 326 x 340 mm
(101/4 x 127/8 x 131/2 in.)
8.2 kg (18 lbs 1 oz)
FRONT SPEAKERS SX-NAJ502
Speaker system
Speaker units
Impedance
Dimensions (W x H x D)
Weight
3 way, bass reflex (magnetic shielded)
Woofer: 160 mm (63/8 in.) cone
Tweeter: 60 mm (23/8 in.) cone
Super tweeter: 20 mm (13/16 in.) ceramic
6 ohms
230 x 324 x 253 mm
(91/8 x 127/8 x 14 in.)
4.5 kg (9 lbs 15 oz)
SURROUND SPEAKERS SX-R290
Speaker system
Speaker units
Impedance
Dimensions (W x H x D)
Weight
Accessories
1 way, bass reflex
Full range: 100 mm (4 in.) cone
8 ohms
150 x 132 x 142 mm
(6 x 51/4 x 55/8 in.)
0.8 kg (1 lbs 12 oz)
Wall mounting screws (2)
CENTER SPEAKER SX-C610
Speaker system
Speaker units
Impedance
Dimensions (W x H x D)
Weight
1 way, bass reflex
Full range: 100 mm (4 in.) cone
8 ohms
260 x 132 x 216 mm
(101/4 x 51/4 x 85/8 in.)
1.0 kg (2 lbs 3 oz)
• Design and specifications are subject to change without notice.
• The word "BBE"and the "BBE symbol" are trademarks of BBE
Sound, Inc.
Under license from BBE Sound,Inc.
• Manufactured under license from Dolby Laboratories Licensing
Corporation.
“DOLBY”, the double-D symbol
and "PRO LOGIC" are trademarks
of Dolby Laboratories Licensing Corporation.
–2–
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING
This set employs laser. Therefore, be sure to follow carefully
the instructions below when servicing.
WARNING!!
WHEN SERVICING, DO NOT APPROACH THE LASER
EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS
NECESSARY TO CONFIRM LASER BEAM EMISSION.
BE SURE TO OBSERVE FROM A DISTANCE OF MORE
THAN 30cm FROM THE SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK.
CAUTION
Use of controls or adjustments or performance of procedures other than those specified herin may result in
hazardous radiation exposure.
ATTENTION
L’utillisation de commandes, réglages ou procédures
autres que ceux spécifiés peut entraîner une dangereuse
exposition aux radiations.
ADVARSEL
s
s
Caution: Invisible laser radiation when
open and interlocks defeated avoid
exposure to beam.
Advarsel: Usynlig laserståling ved åbning,
når sikkerhedsafbrydere er ude af funktion.
Undgå udsættelse for stråling.
Usynlig laserståling ved åbning, når sikkerhedsafbrydereer
ude af funktion. Undgå udsættelse for stråling.
This Compact Disc player is classified as a CLASS 1
LASER product.
The CLASS 1 LASER PRODUCT label is located on the
rear exterior.
VAROITUS!
Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa
mainitulla tavalla saataa altistaa käyt-täjän
turvallisuusluokan 1 ylittävälle näkymättömälle
lasersäteilylle.
CLASS 1
KLASSE 1
LUOKAN 1
KLASS 1
VARNING!
Om apparaten används på annat sätt än vad som
specificeras i denna bruksanvising, kan användaren
utsättas för osynling laserstrålning, som överskrider
gränsen för laserklass 1.
LASER PRODUCT
LASER PRODUKT
LASER LAITE
LASER APPARAT
Precaution to replace Optical block
PICK-UP Assy PWB
(KSS-213F)
Body or clothes electrostatic potential could
ruin laser diode in the optical block. Be sure
ground body and workbench, and use care the
clothes do not touch the diode.
1) After the connection, remove solder shown in
right figure.
Solder
–3–
NOTE ON BEFORE STARTING REPAIR
1. Forced discharge of electrolytic capacitor of power supply block
When repair is going to be attempted in the set that uses relay circuit in the power supply block, electric potential is kept charged across
the electrolytic capacitors (C101, 102) even though AC power cord is removed. If repair is attempted in this condition, secondary defect
can occur.
In order to prevent the secondary trouble, perform the following measures before starting repair work.
Discharge procedure
MAIN C.B
1 Remove the AC power cord.
2 Connect a discharging resistor at an end of lead wire that
has clips at both ends. Connect the other end of the lead
wire to metal chassis.
3 Contact the other end of the discharging resistor to the
positive (+) side (+VH) of C101. (For two seconds)
4 Contact the same end of the discharging resistor as step
3 to the negative (-) side (-VH) of C102 in the same way.
(For two seconds)
5 Check that voltage across C101 and C102 has decreased
to 1 V or less using a multimeter or an oscilloscope.
D101
3
2
Select a discharging resistor referring to the following table.
C102
4
2
Fig-1
Charging voltage (V)
Discharging
(C101, 102)
resistor (Ω)
25-48
100
3
87-A00-247-090
49-140
220
5
87-A00-232-090
Rated power (W)
C101
Parts number
Note: The reference numbers (C101, C102) of the electrolytic capacitors can change depending on the models. Be sure to check the
reference numbers of the charging capacitors on schematic diagram before starting the discharging work.
2. Check items before exchanging the MICROCOMPUTER
Be sure to check the following items before exchanging the MICROCOMPUTER. Exchange the MICROCOMPUTER after confirming
that the MICROCOMPUTER is surely defective.
2-1. Regarding the HOLD terminal of the MICROCOMPUTER
When the HOLD terminal (INPUT) of the MICROCOMPUTER is “H”, the MICROCOMPUTER is judged to be operating correctly.
When this terminal is “L”, the main power cannot be turned on. Therefore, be sure to check the terminal voltage of the HOLD
terminal before exchange.
When the MICROCOMPUTER is not defective, the HOLD terminal can also go “L” when the POWER AMPLIFIER has any
abnormalities that triggers the abnormality detection circuit on the MAIN C. B. that sets the HOLD terminal to “L”.
• Good or no good judgement of the MICROCOMPUTER
1 Turn on the AC main power.
2 Confirm that the main power is turned on and the HOLD terminal of the MICROCOMPUTER keeps the “H” level or not.
3 When the HOLD terminal is “L” level, the abnormality detection circuit is judged to be working correctly and the
MICROCOMPUTER is judged to be good.
–4–
In such a case, check also if the POWER AMPLIFIER circuit or power supply circuit has any abnormalities or not.
2-2. Regarding reset
TE
R
There are cases that the machine does not work correctly because the MICROCOMPUTER is not reset even though the AC power
cord is re-inserted, or the software reset (pressing the STOP key + POWER key) is performed.
When the above described phenomenon occurs, it can lead to wrong judgement as if the MICROCOMPUTER is defective and to
exchange the MICROCOMPUTER. In such a case, perform the forced-reset by the following procedure and check good or no
good of the MICROCOMPUTER.
1 Remove the AC power cord.
M
IC
RO
CO
M
PU
FRONT C.B
18
15
C113
% VSS
MICROC113
COMPUTER
* VDD
FRONT C.B
Short with tweezers.
Fig-2-2
2 Short both ends of the electrolytic capacitor C113 that is connected to VDD of the MICROCOMPUTER with tweezers.
3 Connect the AC power cord again. If the MICROCOMPUTER returns to the normal operation, the MICROCOMPUTER is
good.
Note: The reference number or MICROCOMPUTER pin number of transistor (Q110) and electrolytic capacitor (C113) can change depending
on the models. Be sure to check the reference numbers on schematic diagram before starting the discharging work.
2-3. Confirmation of soldering state of MICROCOMPUTER
Check the soldering state of the MICROCOMPUTER in addition to the above described procedures. Be sure to exchange the
MICROCOMPUTER after surely confirming that the trouble is not caused by poor soldering but the MICROCOMPUTER itself.
–5–
ELECTRICAL MAIN PARTS LIST
REF. NO.
PART NO.
KANRI
NO.
DESCRIPTION
REF. NO.
PART NO.
KANRI
NO.
DESCRIPTION
MAIN C.B
IC
87-A21-893-040
87-A20-783-040
87-A21-703-040
87-A21-916-040
87-A21-884-040
C-IC,NJM14558V-TE2
C-IC,BA7762AFS
C-IC,SN74LV244APW
C-IC,SN74LV125APW
C-IC,CS4228A
C5
C6
C7
C8
C9
87-012-368-080
87-012-368-080
87-012-368-080
87-012-368-080
87-012-368-080
C-CAP,S
C-CAP,S
C-CAP,S
C-CAP,S
C-CAP,S
87-A21-882-030
87-A21-883-040
87-A20-921-040
87-A20-870-010
87-A21-885-040
C-IC,M62466FP
C-IC,CS8415A
C-IC,SN74LVU04APW
IC,GP1F37R
C-IC,CS49326
C10
C11
C12
C21
C22
87-012-368-080
87-012-368-080
87-012-368-080
87-A12-780-090
87-A12-780-090
C-CAP,S 0.1-50 F
C-CAP,S 0.1-50 F
C-CAP,S 0.1-50 F
CAP,E 4700-35 M 85 SKR
CAP,E 4700-35 M 85 SKR
87-A21-695-010
8B-NCK-601-030
87-A21-831-010
87-A21-928-010
87-070-289-040
IC,LA1845L
C-IC,UPD784975AGF-102-3BA
IC,SPS-442-1-F1
IC,LC72131D-N
C-IC,BU2092F
C23
C24
C25
C26
C27
87-A12-779-090
87-A12-779-090
87-A12-095-080
87-A12-095-080
87-A12-095-080
CAP,E
CAP,E
CAP,E
CAP,E
CAP,E
87-020-903-010
87-A21-269-010
IC,NJM7805FA
IC,EW732
C28
C30
C31
C32
C33
87-A12-095-080
87-010-430-080
87-A12-062-080
87-012-286-080
87-A12-062-080
CAP,E 100-50 SMG
CAP, ELECT 100-63
CAP,E 100-10 SMG
CAP, U 0.01-25
CAP,E 100-10 SMG
87-026-609-080
87-A30-559-010
87-026-610-080
87-A30-076-080
87-A30-075-080
TR,KTA1266GR
TR,CSB1370EF
TR,KTC3198GR
C-TR,2SC3052F
C-TR,2SA1235F
C34
C35
C36
C40
C60
87-A12-095-080
87-A12-076-080
87-A12-068-080
87-012-286-080
87-A12-089-080
CAP,E 100-50 SMG
CAP,E 22-35 SMG
CAP,E 470-16 SMG
CAP, U 0.01-25
CAP,E 3.3-50 SMG
87-A30-495-080
87-A30-074-080
87-A30-468-080
87-A30-106-040
87-A30-086-040
TR,2SA1981Y
C-TR,RT1P141C
C-TR,KRC102S-RTK
C-TR,CMBT5551
C-TR,CSD1306E
C63
C81
C97
C101
C102
87-A12-071-080
87-A10-918-080
87-010-831-080
87-A12-087-080
87-A12-087-080
CAP,E 47-25 SMG
CAP,E 100-16 SMG
C-CAP,U,0.1-16F
CAP,E 1-50 SMG
CAP,E 1-50 SMG
87-A30-256-010
87-A30-255-010
87-A30-107-070
87-A30-484-080
87-A30-494-080
TR,2SD1933
TR,2SB1342
C-TR,CMBT5401
C-TR,KRA102S
TR,2SA1980G
C110
C111
C112
C113
C121
87-010-831-080
87-A12-088-080
87-A12-088-080
87-A12-075-080
87-A12-088-080
C-CAP,U 0.1-16 Z F
CAP,E 2.2-50 SMG
CAP,E 2.2-50 SMG
CAP,E 10-35 SMG
CAP,E 2.2-50 SMG
87-A30-190-080
87-A30-529-010
87-A30-528-010
87-A30-105-080
87-A30-162-010
TR,CC5551
TR,2SD2642
TR,2SB1686
C-TR,RT1P441C
FET,2SK2937
C122
C145
C146
C147
C148
87-A12-086-080
87-012-368-080
87-012-368-080
87-012-368-080
87-012-368-080
CAP,E 0.47-50 SMG
C-CAP,S 0.1-50 F
C-CAP,S 0.1-50 F
C-CAP,S 0.1-50 F
C-CAP,S 0.1-50 F
87-A30-087-080
87-A30-582-080
87-A30-234-080
87-A30-288-040
89-327-143-080
C-FET,2SK2158
TR,CDA1585BC
TR,CSC4115BC
C-TR,DTC114YKA
C-TR,2SC2714O
C155
C170
C171
C173
C201
87-010-831-080
87-012-278-080
87-012-282-080
87-010-759-080
87-012-281-080
C-CAP,U,0.1-16F
C-CAP,U 2200P-50 B
CAP, U 4700P-50
C-CAP,U, 0.1-25F
C-CAP,U 3900P-50 B
87-A30-489-080
C-TR,KRA107S
C202
C203
C204
C205
C206
87-012-281-080
87-A12-084-080
87-A12-084-080
87-012-282-080
87-012-282-080
C-CAP,U 3900P-50 B
CAP,E 0.22-50 SMG
CAP,E 0.22-50 SMG
CAP, U 4700P-50
CAP, U 4700P-50
87-A40-839-090
87-A40-291-080
87-A40-838-090
87-A40-553-080
87-A40-778-080
DIODE,G5SBA60L-6088
DIODE,1N4148M(CPT)
DIODE,G3SBA60L-6088
DIODE,1N4003 LES
ZENER,UZ30BSD
C207
C208
C209
C210
C211
87-A12-090-080
87-A12-090-080
87-016-615-080
87-016-615-080
87-A12-078-080
CAP,E 4.7-50 SMG
CAP,E 4.7-50 SMG
C-CAP,U 2.2P-50CH
C-CAP,U 2.2P-50CH
CAP,E 47-35 SMG
87-A40-764-080
87-A40-270-080
87-A40-269-080
87-A40-488-080
87-A40-202-080
ZENER,UZ10BSC
C-DIODE,MC2838
C-DIODE,MC2836
DIODE,1SS244
ZENER,UZ5.1BSB
C212
C215
C216
C217
C218
87-A12-078-080
87-012-273-080
87-012-273-080
87-A10-596-080
87-A10-596-080
CAP,E 47-35 SMG
C-CAP,U 820P-50 B
C-CAP,U 820P-50 B
C-CAP,S 100P-100 J CH
C-CAP,S 100P-100 J CH
87-A40-749-080
87-A40-393-090
87-A40-748-080
87-A40-747-080
87-A40-745-080
ZENER,UZ5.6BSB
DIODE,1N5402GW(F20)
ZENER,UZ5.6BSA
ZENER,UZ5.1BSB
ZENER,UZ4.7BSA
C219
C220
C221
C222
C223
87-012-368-080
87-012-368-080
87-012-286-080
87-012-286-080
87-A10-596-080
C-CAP,S 0.1-50 F
C-CAP,S 0.1-50 F
CAP, U 0.01-25
CAP, U 0.01-25
C-CAP,S 100P-100 J CH
87-A40-739-080
87-017-149-080
ZENER,UZ 2.7BSA
ZENER,HZS6A2L
C224
C273
C274
87-A10-596-080
87-010-759-080
87-A12-091-080
C-CAP,S 100P-100 J CH
C-CAP,U, 0.1-25F
CAP,E 10-50 SMG
TRANSISTOR
DIODE
–6–
0.1-50
0.1-50
0.1-50
0.1-50
0.1-50
F
F
F
F
F
3300-50 M 85 SKR
3300-50 M 85 SKR
100-50 SMG
100-50 SMG
100-50 SMG
REF. NO.
PART NO.
C275
C301
C301
C302
C303
KANRI
NO.
87-A12-091-080
87-012-278-080
87-012-188-080
87-012-188-080
87-012-268-080
DESCRIPTION
CAP,E 10-50 SMG
C-CAP,U 2200P-50 B
C-CAP,U 47P-50 CH
C-CAP,U 47P-50 CH
C-CAP,U 330P-50 B
C304
C305
C306
C307
C309
87-012-268-080
87-012-268-080
87-012-268-080
87-010-759-080
87-010-759-080
C310
C311
C312
C313
C314
REF. NO.
C689
C701
C702
C703
C707
KANRI
NO.
87-A12-058-080
87-012-195-080
87-012-195-080
87-012-286-080
87-A12-088-080
CAP,E 470-6.3 M SMG
C-CAP,U 100P-50CH
C-CAP,U 100P-50CH
CAP, U 0.01-25
CAP,E 2.2-50 SMG
C-CAP,U 330P-50 B
C-CAP,U 330P-50 B
C-CAP,U 330P-50 B
C-CAP,U, 0.1-25F
C-CAP,U, 0.1-25F
C708
C772
C782
C783
C784
87-A12-088-080
87-012-286-080
87-012-286-080
87-012-286-080
87-012-286-080
CAP,E 2.2-50 SMG
CAP, U 0.01-25
CAP, U 0.01-25
CAP, U 0.01-25
CAP, U 0.01-25
87-010-759-080
87-010-787-080
87-010-787-080
87-012-276-080
87-012-276-080
C-CAP,U, 0.1-25F
CAP, U 0.022-25
CAP, U 0.022-25
CAP, CHIP SS 1500 PBK
CAP, CHIP SS 1500 PBK
C785
C786
C788
C789
C790
87-012-286-080
87-012-286-080
87-012-167-080
87-A12-052-080
87-A12-052-080
CAP, U 0.01-25
CAP, U 0.01-25
C-CAP,U 5P-50 CH
C-CAP,S 0.033-25 J B
C-CAP,S 0.033-25 J B
C315
C316
C321
C322
C324
87-012-278-080
87-012-278-080
87-012-142-080
87-012-142-080
87-A12-071-080
C-CAP,U 2200P-50 B
C-CAP,U 2200P-50 B
CAP, S 0.33-16
CAP, S 0.33-16
CAP,E 47-25 SMG
C791
C792
C793
C795
C796
87-010-831-080
87-012-286-080
87-A12-090-080
87-012-286-080
87-012-286-080
C-CAP,U,0.1-16F
CAP, U 0.01-25
CAP,E 4.7-50 SMG
CAP, U 0.01-25
CAP, U 0.01-25
C325
C327
C328
C332
C333
87-A12-057-080
87-A12-090-080
87-A12-090-080
87-010-759-080
87-016-251-080
CAP,E 330-6.3 SMG
CAP,E 4.7-50 SMG
CAP,E 4.7-50 SMG
C-CAP,U, 0.1-25F
CAP,E 220-16 M SMG
C797
C798
C799
C800
C801
87-A12-091-080
87-012-286-080
87-A12-093-080
87-010-829-080
87-A12-089-080
CAP,E 10-50 SMG
CAP, U 0.01-25
CAP,E 33-50 SMG
CAP, U 0.047-16
CAP,E 3.3-50 SMG
C335
C336
C337
C339
C340
87-A12-087-080
87-A12-087-080
87-010-759-080
87-010-759-080
87-010-759-080
CAP,E 1-50 SMG
CAP,E 1-50 SMG
C-CAP,U, 0.1-25F
C-CAP,U, 0.1-25F
C-CAP,U, 0.1-25F
C802
C803
C803
C804
C807
87-010-829-080
87-010-787-080
87-012-280-080
87-A12-062-080
87-A12-086-080
CAP, U 0.047-16
CAP, U 0.022-25
CAP, U 3300P-50
CAP,E 100-10 SMG
CAP,E 0.47-50 SMG
C351
C352
C354
C355
C356
87-012-270-080
87-012-270-080
87-012-271-080
87-012-274-080
87-A12-071-080
CAP, U 470P-50
CAP, U 470P-50
CAP, U 560P-50
CHIP CAP,U 1000P-50B
CAP,E 47-25 SMG
C808
C809
C810
C814
C815
87-A12-087-080
87-A12-087-080
87-010-831-080
87-012-286-080
87-A12-086-080
CAP,E 1-50 SMG
CAP,E 1-50 SMG
C-CAP,U,0.1-16F
CAP, U 0.01-25
CAP,E 0.47-50 SMG
C357
C358
C359
C360
C363
87-012-286-080
87-012-279-080
87-012-279-080
87-012-279-080
87-A12-361-080
CAP, U 0.01-25
C-CAP,U 2700P-50 B
C-CAP,U 2700P-50 B
C-CAP,U 2700P-50 B
CAP,M 5600P-100 J CP
C816
C821
C823
C824
C825
87-A12-086-080
87-A12-091-080
87-010-177-080
87-A12-090-080
87-010-596-080
CAP,E 0.47-50 SMG
CAP,E 10-50 SMG
C-CAP,S 820P-50 SL
CAP,E 4.7-50 SMG
CAP, S 0.047-16
C370
C373
C374
C378
C379
87-010-759-080
87-A10-060-080
87-A10-060-080
87-010-759-080
87-A12-069-080
C-CAP,U, 0.1-25F
C-CAP,S 0.18-16 K B
C-CAP,S 0.18-16 K B
C-CAP,U, 0.1-25F
CAP,E 22-25 SMG
C831
C842
C844
C850
C851
87-010-406-080
87-012-286-080
87-012-286-080
87-A12-071-080
87-012-286-080
CAP, ELECT 22-50
CAP, U 0.01-25
CAP, U 0.01-25
CAP,E 47-25 SMG
CAP, U 0.01-25
C380
C386
C388
C391
C392
87-A12-069-080
87-010-759-080
87-012-266-080
87-012-191-080
87-012-191-080
CAP,E 22-25 SMG
C-CAP,U, 0.1-25F
C-CAP,U 220P-50 B
C-CAP,U 56P-50 J CH
C-CAP,U 56P-50 J CH
C852
C853
C858
C859
C860
87-012-286-080
87-012-286-080
87-010-831-080
87-010-759-080
87-012-286-080
CAP, U 0.01-25
CAP, U 0.01-25
C-CAP,U,0.1-16F
C-CAP,U, 0.1-25F
CAP, U 0.01-25
C393
C394
C619
C621
C622
87-012-191-080
87-012-191-080
87-010-831-080
87-012-278-080
87-012-278-080
C-CAP,U 56P-50 J CH
C-CAP,U 56P-50 J CH
C-CAP,U,0.1-16F
C-CAP, U 2200P-50 K B
C-CAP, U 2200P-50 K B
C913
C918
C959
C960
C961
87-012-286-080
87-A10-039-080
87-010-831-080
87-010-831-080
87-012-167-080
CAP, U 0.01-25
C-CAP,U 470P-50 J CH
C-CAP,U 0.1-16F
C-CAP,U,0.1-16F
C-CAP,U 5P-50 CH
C633
C634
C635
C636
C637
87-012-281-080
87-016-369-080
87-012-281-080
87-016-369-080
87-A12-088-080
C-CAP,U 3900P-50
C-CAP,S 0.033-25
C-CAP,U 3900P-50
C-CAP,S 0.033-25
CAP,E 2.2-50 SMG
C963
C971
C972
C973
C974
87-015-785-080
87-A12-067-080
87-A12-090-080
87-012-286-080
87-012-286-080
CHIP CAPACITOR, 0.1FZ-25Z
CAP,E 330-16 SMG
CAP,E 4.7-50 SMG
CAP, U 0.01-25
CAP, U 0.01-25
C638
C656
C675
C676
C683
87-A12-088-080
87-A10-260-080
87-012-282-080
87-012-282-080
87-A11-969-080
CAP,E 2.2-50 SMG
C-CAP,U 0.1-16 K B
CAP, U 4700P-50
CAP, U 4700P-50
C-CAP,U 0.082U-16 K B
C979
C981
C982
C983
C984
87-012-195-080
87-A12-071-080
87-010-831-080
87-012-286-080
87-012-286-080
C-CAP,U 100P-50CH
CAP,E 47-25 SMG
C-CAP,U,0.1-16F
CAP, U 0.01-25
CAP, U 0.01-25
C684
C685
C686
C687
C688
87-A12-075-080
87-012-167-080
87-010-759-080
87-010-759-080
87-A12-062-080
CAP,E 10-35 SMG
C-CAP,U 5P-50 CH
C-CAP,U, 0.1-25F
C-CAP,U, 0.1-25F
CAP,E 100-10 SMG
C987
C991
C992
C993
C995
87-012-286-080
87-012-176-080
87-012-176-080
87-012-274-080
87-012-274-080
CAP, U 0.01-25
CAP 15P
CAP 15P
CHIP CAP,U 1000P-50B
CHIP CAP,U 1000P-50B
B
B K
B
B K
–7–
PART NO.
DESCRIPTION
REF. NO.
PART NO.
C997
C998
C999
CF831
CF832
KANRI
NO.
87-010-831-080
87-A12-071-080
87-A11-155-080
87-008-261-010
87-008-261-010
DESCRIPTION
C-CAP,U,0.1-16F
CAP,E 47-25 SMG
CAP,TC U 0.01-16 Z F
FILTER, SFE10.7MA5
FILTER, SFE10.7MA5
CN105
CN183
CN301
CN351
CN601
87-099-195-010
87-099-564-010
87-A60-620-010
87-A60-625-010
87-099-719-010
CN701
CN703
CNA1
CNA102
CNA602
C501
C502
C503
C504
C601
KANRI
NO.
87-012-195-080
87-012-195-080
87-012-195-080
87-010-759-080
87-010-382-040
C-CAP,U 100P-50CH
C-CAP,U 100P-50CH
C-CAP,U 100P-50CH
C-CAP,U, 0.1-25F
CAP,E 22-25 SME
CONN,7P V BLK 6216
CONN,4P V TUC-P4P-B1
CONN,3P V 2MM JMT
CONN,8P V 2MM JMT
CONN,30P H BLK(X)
C801
C802
C803
C804
C805
87-A10-804-080
87-010-316-080
87-012-280-080
87-A10-592-080
87-012-184-080
C-CAP,S
C-CAP,S
C-CAP,U
C-CAP,S
C-CAP,U
87-A60-061-010
87-010-385-040
8A-NF6-646-010
8A-NF8-655-010
87-A60-632-010
CONN,06P V 9604S-06C
CAP,E 220-25 M SME
CONN ASSY,9P TID-A(460)
CONN ASSY,7P TID-A(150)
CONN 15P V 2MM JMT
C806
C807
C808
C809
C810
87-012-274-080
87-012-274-080
87-010-544-040
87-010-404-040
87-016-114-080
CHIP CAP,U 1000P-50B
CHIP CAP,U 1000P-50B
CAP,E 0.1-50 SME
CAP,E 4.7-50 SME
C-CAP,U0.01-25B
FFC105
FFC701
FFE831
J101
J102
88-907-121-110
88-906-251-110
A8-6ZA-19M-030
87-A60-929-010
87-A60-238-010
FF-CABLE,7P 120
FF-CABLE,6P 1.25
6ZA-1 YFEMENM
JACK,DIA6.3 BLK ST W/S TAI
TERMINAL,SP 4P (MSC)
C811
C901
C902
C903
C904
87-A12-052-080
87-012-195-080
87-012-195-080
87-012-195-080
87-012-195-080
C-CAP,S
C-CAP,U
C-CAP,U
C-CAP,U
C-CAP,U
0.033-25 J B
100P-50CH
100P-50CH
100P-50CH
100P-50CH
J603
J831
L141
L142
L301
87-A60-881-010
87-A60-202-010
87-A50-610-010
87-A50-610-010
87-A50-625-010
JACK,PIN 2P MSP 242V05 PBSN
TERMINAL,ANT 4P MSP-154V-02
COIL,1UH K(MDEC)
COIL,1UH K(MDEC)
COIL,TRAP 85KHZ (SANWA)
C905
C906
C907
C908
C909
87-012-195-080
87-012-195-080
87-012-195-080
87-012-195-080
87-012-195-080
C-CAP,U
C-CAP,U
C-CAP,U
C-CAP,U
C-CAP,U
100P-50CH
100P-50CH
100P-50CH
100P-50CH
100P-50CH
L302
L351
L801
L802
L811
87-A50-625-010
87-007-342-010
87-A50-608-010
87-A91-552-010
87-005-847-080
COIL,TRAP 85KHZ (SANWA)
COIL,OSC 85KHZ BIAS
COIL,FM DET-N(TOK)
FLTR,MT-450AL(TOK)
COIL,2.2UH K CECS
C910
C911
C912
C913
C914
87-012-195-080
87-012-274-080
87-010-759-080
87-A11-242-040
87-A11-242-040
C-CAP,U 100P-50CH
CHIP CAP,U 1000P-50B
C-CAP,U, 0.1-25F
CAP,E 220-10 M 5L SRM
CAP,E 220-10 M 5L SRM
L832
L909
L951
R85
R86
87-005-847-080
87-A91-639-010
8A-NF8-667-010
87-A00-436-050
87-A00-436-050
COIL,2.2UH K CECS
TRANS,BALUN FM
COIL,AM PACK 4(TOK)
RES,100-1/2W J RP
RES,100-1/2W J RP
C915
C916
C917
C919
C920
87-010-759-080
87-010-759-080
87-010-759-080
87-012-286-080
87-010-757-080
C-CAP,U, 0.1-25F
C-CAP,U, 0.1-25F
C-CAP,U, 0.1-25F
CAP, U 0.01-25
C.CAP,U 0.047-25F
R87
R88
R149
R150
R151
87-A00-436-050
87-A00-436-050
87-A01-001-050
87-A01-001-050
87-A01-001-050
RES,100-1/2W
RES,100-1/2W
RES,220-1/2W
RES,220-1/2W
RES,220-1/2W
C921
C951
C952
C953
C961
87-012-282-080
87-012-176-080
87-012-198-080
87-A10-039-080
87-010-378-040
CAP, U 4700P-50
C-CAP,U 15P-50 J CH
C-CAP,U 180P-50 J CH
C-CAP,U 470P-50 J CH
CAP,E 10-16
R152
R255
R256
R259
R260
87-A01-001-050
87-A00-262-080
87-A00-262-080
87-A00-262-080
87-A00-262-080
RES,220-1/2W J BLT2J
RES,M/F 0.15-2W J
RES,M/F 0.15-2W J
RES,M/F 0.15-2W J
RES,M/F 0.15-2W J
C962
C963
CN104
CN701
CN731
87-012-157-080
87-010-759-080
87-A60-057-010
87-099-720-010
87-099-196-010
C-CAP,S 330P-50 CH
C-CAP,U, 0.1-25F
CONN,11P V 9604S-11C
CONN,30P BLK B(P)
CONN,8P V BLK 6216
R790
R991
R993
R995
SFR351
87-012-286-080
87-012-195-080
87-012-195-080
87-012-195-080
87-A90-433-080
CAP, U 0.01-25
C-CAP,U 100P-50CH
C-CAP,U 100P-50CH
C-CAP,U 100P-50CH
SFR,50K H NVZ6TLTA
CN732
FFC104
FFC731
FFC732
FL901
87-099-014-010
88-911-101-110
88-908-301-110
88-912-371-110
8B-NCK-605-010
CONN,12P V BLK 6216
FF-CABLE, 11P 1.25
FF-CABLE, 8P 1.25
FF-CABLE,12P 1.25 37
FL,HNA-08MM29
SFR352
TH201
TH202
WH1
WH102
87-A90-433-080
87-A91-042-080
87-A91-042-080
87-A90-510-010
87-A90-460-010
SFR,50K H NVZ6TLTA
C-THMS,100K 55001
C-THMS,100K 55001
HLDR,WIRE 2.5-9P
HLDR,WIRE 2.5-7P
L951
LED201
LED202
LED203
LED204
87-A50-652-010
87-A40-606-040
87-A40-606-040
87-A40-606-040
87-A40-606-040
COIL,OSC 15.6MHZ
LED,SLR-332VC
LED,SLR-332VC
LED,SLR-332VC
LED,SLR-332VC
X992
87-A70-306-010
VIB,XTAL 4.500MHZ CSA-309ST
LED209
S321
S322
S323
S324
87-A40-317-080
87-A90-095-080
87-A90-095-080
87-A90-095-080
87-A90-095-080
LED,SLR-342VCT31 RED
SW,TACT EVQ11G04M
SW,TACT EVQ11G04M
SW,TACT EVQ11G04M
SW,TACT EVQ11G04M
C153
C154
C155
C156
C301
87-010-787-080
87-A12-078-040
87-010-404-040
87-010-404-040
87-012-278-080
CAP, U 0.022-25
CAP,E 47-35 SMG
CAP,E 4.7-50 SME
CAP,E 4.7-50 SME
C-CAP,U 2200P-50 K B
S325
S326
S327
S328
S329
87-A90-095-080
87-A90-095-080
87-A90-095-080
87-A90-095-080
87-A90-095-080
SW,TACT
SW,TACT
SW,TACT
SW,TACT
SW,TACT
EVQ11G04M
EVQ11G04M
EVQ11G04M
EVQ11G04M
EVQ11G04M
C351
C361
C362
C371
C372
87-A10-201-080
87-012-274-080
87-012-274-080
87-012-274-080
87-012-274-080
C-CAP,S 0.33-16 K B
CHIP CAP,U 1000P-50B
CHIP CAP,U 1000P-50B
CHIP CAP,U 1000P-50B
CHIP CAP,U 1000P-50B
S330
S331
S332
S333
S334
87-A90-095-080
87-A90-095-080
87-A90-095-080
87-A90-095-080
87-A90-095-080
SW,TACT
SW,TACT
SW,TACT
SW,TACT
SW,TACT
EVQ11G04M
EVQ11G04M
EVQ11G04M
EVQ11G04M
EVQ11G04M
J
J
J
J
J
REF. NO.
RP
RP
BLT2J
BLT2J
BLT2J
FRONT C.B
–8–
PART NO.
DESCRIPTION
0.1-25 J B
33P-50 CH
3300P-50 K B
0.015-50
33P-50 CH
REF. NO.
PART NO.
S335
S341
S342
S343
S344
KANRI
NO.
87-A90-095-080
87-A90-095-080
87-A90-095-080
87-A90-095-080
87-A90-095-080
DESCRIPTION
SW,TACT
SW,TACT
SW,TACT
SW,TACT
SW,TACT
EVQ11G04M
EVQ11G04M
EVQ11G04M
EVQ11G04M
EVQ11G04M
S345
S346
S347
S348
S349
87-A90-095-080
87-A90-095-080
87-A90-095-080
87-A90-095-080
87-A90-095-080
SW,TACT
SW,TACT
SW,TACT
SW,TACT
SW,TACT
EVQ11G04M
EVQ11G04M
EVQ11G04M
EVQ11G04M
EVQ11G04M
S361
S371
87-A92-172-010
87-A92-057-010
C101
C102
C103
C104
C105
REF. NO.
C216
C217
C219
C221
C223
KANRI
NO.
87-A11-538-080
87-012-277-080
87-012-277-080
87-012-282-080
87-A12-091-080
C-CAP,S 0.12-25 J B
C-CAP,U 1800P-50 K B GRM
C-CAP,U 1800P-50 K B GRM
CAP, U 4700P-50
CAP,E 10-50 SMG
C224
C401
C404
C503
C504
87-A12-091-080
87-A10-260-080
87-A10-260-080
87-A12-088-080
87-A12-088-080
CAP,E 10-50 SMG
C-CAP,U 0.1-16 K B
C-CAP,U 0.1-16 K B
CAP,E 2.2-50 SMG
CAP,E 2.2-50 SMG
SW,RTRY EC12E24204-25MM OFF
SW,RTRY EC12E12504-25MM OFF
C505
C506
C507
C508
C511
87-A12-090-080
87-A12-090-080
87-A12-090-080
87-A12-090-080
87-012-275-080
CAP,E 4.7-50 SMG
CAP,E 4.7-50 SMG
CAP,E 4.7-50 SMG
CAP,E 4.7-50 SMG
C-CAP,U 1200P-50
87-A12-091-080
87-A12-091-080
87-012-172-080
87-012-172-080
87-010-831-080
CAP,E 10-50 SMG
CAP,E 10-50 SMG
CAPACITOR CHIP U 10P CH
CAPACITOR CHIP U 10P CH
C-CAP,U,0.1-16F
C512
C513
C551
C552
C553
87-012-275-080
87-A10-918-080
87-A10-047-080
87-A10-047-080
87-010-831-080
C-CAP,U 1200P-50
CAP,E 100-16 SMG
C-CAP,U 1-10 Z F
C-CAP,U 1-10 Z F
C-CAP,U 0.1-16 Z F
C106
C107
C108
C113
C114
87-010-831-080
87-A12-091-080
87-A12-091-080
87-012-268-080
87-012-268-080
C-CAP,U,0.1-16F
CAP,E 10-50 SMG
CAP,E 10-50 SMG
C-CAP,U 330P-50 B
C-CAP,U 330P-50 B
C601
C602
C603
C604
C606
87-A12-091-080
87-A10-260-080
87-A12-091-080
87-A10-260-080
87-012-195-080
CAP,E 10-50 SMG
C-CAP,U 0.1-16 K B
CAP,E 10-50 SMG
C-CAP,U 0.1-16 K B
C-CAP,U 100P-50CH
C115
C116
C117
C118
C119
87-012-284-080
87-012-284-080
87-012-277-080
87-012-277-080
87-012-282-080
CAP, U 6800P-50
CAP, U 6800P-50
C-CAP,U 1800P-50 CH
C-CAP,U 1800P-50 CH
CAP, U 4700P-50
C617
C618
C621
C624
C651
87-A12-087-080
87-010-831-080
87-A12-091-080
87-A10-260-080
87-016-251-080
CAP,E 1-50 SMG
C-CAP,U,0.1-16F
CAP,E 10-50 SMG
C-CAP,U 0.1-16 K B
CAP,E 220-16 M SMG
C120
C121
C122
C123
C124
87-012-282-080
87-012-277-080
87-012-277-080
87-A12-091-080
87-A12-091-080
CAP, U 4700P-50
C-CAP,U 1800P-50 CH
C-CAP,U 1800P-50 K B GRM
CAP,E 10-50 SMG
CAP,E 10-50 SMG
C653
C654
C655
C656
C657
87-010-831-080
87-010-831-080
87-A12-087-080
87-A12-091-080
87-010-831-080
C-CAP,U,0.1-16F
C-CAP,U,0.1-16F
CAP,E 1-50 SMG
CAP,E 10-50 SMG
C-CAP,U,0.1-16F
C125
C126
C151
C152
C153
87-A10-902-080
87-A12-091-080
87-A12-091-080
87-A12-091-080
87-012-172-080
C-CAP,U 0.47-10 K B
CAP,E 10-50 SMG
CAP,E 10-50 SMG
CAP,E 10-50 SMG
CAPACITOR CHIP U 10P CH
C658
C659
C701
C702
C703
87-010-831-080
87-010-831-080
87-012-195-080
87-A11-969-080
87-010-831-080
C-CAP,U,0.1-16F
C-CAP,U,0.1-16F
C-CAP,U 100P-50CH
C-CAP,S 0.082U-16 K B
C-CAP,U,0.1-16F
C154
C155
C156
C157
C161
87-012-172-080
87-010-831-080
87-010-831-080
87-A10-902-080
87-012-268-080
CAPACITOR CHIP U 10P CH
C-CAP,U,0.1-16F
C-CAP,U,0.1-16F
C-CAP,U 0.47-10 K B
C-CAP,U 330P-50 B
C704
C706
C707
C709
C711
87-012-278-080
87-012-180-080
87-012-180-080
87-012-180-080
87-010-831-080
C-CAP,U 2200P-50
C-CAP,U 470-50 J
C-CAP,U 470-50 J
C-CAP,U 470-50 J
C-CAP,U,0.1-16F
C162
C163
C164
C165
C166
87-012-268-080
87-010-831-080
87-010-831-080
87-012-284-080
87-012-284-080
C-CAP,U 330P-50 B
C-CAP,U,0.1-16F
C-CAP,U,0.1-16F
CAP, U 6800P-50
CAP, U 6800P-50
C712
C715
C721
C722
C723
87-A12-062-080
87-012-286-080
87-012-167-080
87-012-167-080
87-010-831-080
CAP,E 100-10 SMG
CAP, U 0.01-25
C-CAP,U 5P-50 CH
C-CAP,U 5P-50 CH
C-CAP,U,0.1-16F
C167
C168
C169
C170
C171
87-012-277-080
87-012-277-080
87-012-277-080
87-012-277-080
87-012-282-080
C-CAP,U 1800P-50
C-CAP,U 1800P-50
C-CAP,U 1800P-50
C-CAP,U 1800P-50
CAP, U 4700P-50
C751
C801
C802
C804
C805
87-012-278-080
87-010-831-080
87-012-286-080
87-012-270-080
87-A12-088-080
C-CAP,U 2200P-50 B
C-CAP,U,0.1-16F
CAP, U 0.01-25
CAP, U 470P-50
CAP,E 2.2-50 SMG
C172
C173
C174
C201
C202
87-012-282-080
87-A12-091-080
87-A12-091-080
87-A12-091-080
87-A12-091-080
CAP, U 4700P-50
CAP,E 10-50 SMG
CAP,E 10-50 SMG
CAP,E 10-50 SMG
CAP,E 10-50 SMG
C810
C818
C819
C820
C823
87-012-267-080
87-010-831-080
87-A12-062-080
87-010-831-080
87-010-831-080
C-CAP,U 270P-50 B
C-CAP,U,0.1-16F
CAP,E 100-10 SMG
C-CAP,U,0.1-16F
C-CAP,U,0.1-16F
C203
C204
C205
C206
C207
87-012-172-080
87-012-274-080
87-010-831-080
87-010-831-080
87-A10-902-080
CAPACITOR CHIP U 10P CH
CHIP CAP,U 1000P-50B
C-CAP,U,0.1-16F
C-CAP,U,0.1-16F
C-CAP,U 0.47-10 K B
C824
C825
C826
C828
CN101
87-A12-087-080
87-A12-087-080
87-A12-087-080
87-018-127-080
87-009-551-010
CAP,E 1-50 SMG
CAP,E 1-50 SMG
CAP,E 1-50 SMG
CAP,TC U 470P-50 K B
CONN,15P V PH
C211
C212
C213
C214
C215
87-012-268-080
87-016-115-080
87-010-831-080
87-010-831-080
87-012-284-080
C-CAP,U 330P-50 B
C-CAP,U 0.012-25 J B
C-CAP,U,0.1-16F
C-CAP,U,0.1-16F
CAP, U 6800P-50
CN402
CN651
FB601
FB602
FB701
87-A60-056-010
87-049-919-010
87-008-372-080
87-008-372-080
87-008-372-080
CONN,12P V 9604S-12C
CONN,3P V WHT EH
FILTER, EMI BL OIRNI
FILTER, EMI BL OIRNI
FILTER, EMI BL OIRNI
AC3 C.B
K
K
K
K
B
B
B
B
GRM
GRM
GRM
GRM
–9–
PART NO.
DESCRIPTION
B
CH
CH
CH
REF. NO.
FB702
FB801
FB802
X701
PART NO.
KANRI
NO.
87-008-372-080
87-008-372-080
87-008-372-080
87-A70-115-010
DESCRIPTION
REF. NO.
C101
C102
C103
C104
C107
87-012-278-080
87-012-278-080
87-A12-087-080
87-A12-087-080
87-A12-095-080
C-CAP,U 2200P-50 B
C-CAP,U 2200P-50 B
CAP,E 1-50 SMG
CAP,E 1-50 SMG
CAP,E 100-50 SMG
C108
C111
C112
C113
C114
87-A12-095-080
87-A12-078-080
87-A12-078-080
87-012-195-080
87-012-195-080
CAP,E 100-50 SMG
CAP,E 47-35 SMG
CAP,E 47-35 SMG
C-CAP,U 100P-50CH
C-CAP,U 100P-50CH
C117
C118
C119
C120
C121
87-A10-596-080
87-A10-596-080
87-012-368-080
87-012-368-080
87-012-286-080
C-CAP,S 100P-100 J CH
C-CAP,S 100P-100 J CH
C-CAP,S 0.1-50 F
C-CAP,S 0.1-50 F
CAP, U 0.01-25
C122
C125
C201
C202
C204
87-012-286-080
87-010-831-080
87-012-278-080
87-A12-087-080
87-A12-095-080
CAP, U 0.01-25
C-CAP,U,0.1-16F
C-CAP,U 2200P-50 B
CAP,E 1-50 SMG
CAP,E 100-50 SMG
C206
C207
C209
C210
C211
87-A12-078-080
87-012-195-080
87-A10-596-080
87-012-368-080
87-012-286-080
CAP,E 47-35 SMG
C-CAP,U 100P-50CH
C-CAP,S 100P-100 J CH
C-CAP,S 0.1-50 F
CAP, U 0.01-25
C300
C301
C714
CN102
CN104
87-012-278-080
87-012-282-080
87-012-286-080
87-A61-109-010
87-A60-060-010
C-CAP,U 2200P-50 B
CAP, U 4700P-50
CAP, U 0.01-25
CONN,7P V TID-A
CONN,07P V 9604S-07C
R157
R158
R161
R162
R230
87-A00-258-080
87-A00-258-080
87-A00-258-080
87-A00-258-080
87-A00-258-080
RES,M/F
RES,M/F
RES,M/F
RES,M/F
RES,M/F
R231
TH101
TH102
TH201
W201
87-A00-258-080
87-A91-042-080
87-A91-042-080
87-A91-042-080
8B-NCK-607-010
RES,M/F 0.22-1W J
C-THMS,100K 55001
C-THMS,100K 55001
C-THMS,100K 55001
F-CABLE,6P 2.5 130MM
WH201
87-A90-508-010
HLDR,WIRE 2.5-6P
KANRI
NO.
DESCRIPTION
PT C.B
FILTER, EMI BL OIRNI
FILTER, EMI BL OIRNI
FILTER, EMI BL OIRNI
VIB,XTAL 12.288MHZ
AMP C.B
PART NO.
!
!
!
C1
CN1
PT1
PT2
RY2
87-A10-831-010
87-A61-110-010
8B-NCK-612-010
8B-MA6-671-010
87-A91-418-010
CAP,E 1000-25 M SMG
CONN,9P V TID-A
PT BNC-19 U
PT,SUB BMA U (VRK)
RELAY,AC12V G5PA-1-M
!
!
T1
T2
87-A60-317-010
87-A60-317-010
TERMINAL, 1P MSC
TERMINAL, 1P MSC
87-A12-087-080
87-010-379-080
87-A12-071-080
87-009-030-010
87-A60-688-010
CAP,E 1-50 SMG
CAP,E 22-16 M 11L SME
CAP,E 47-25 SMG
CONN,2P V WHT PH
CONN,4P H GRY TUC-P04X-C1
8B-NCK-610-010
CONN ASSY,3P BNC-K
C401
C402
C403
C404
C411
87-012-368-080
87-012-368-080
87-012-368-080
87-012-368-080
87-012-368-080
C-CAP,S
C-CAP,S
C-CAP,S
C-CAP,S
C-CAP,S
C412
J201
L401
L402
L411
87-012-368-080
87-A61-540-010
87-A50-610-010
87-A50-610-010
87-A50-610-010
C-CAP,S 0.1-50 F
JACK,PIN 4P ORBW MSP-244V -41
COIL,1UH K(MDEC)
COIL,1UH K(MDEC)
COIL,1UH K(MDEC)
WH401
87-A90-508-010
HLDR,WIRE 2.5-6P
CN1
CNA351
SFR1
SOL1
SOL2
87-099-753-010
86-ZM3-605-110
87-024-581-010
82-ZM3-627-010
82-ZM3-627-010
CONN,11P H 9604
CONN ASSY,8P-RPB
SFR,3.3K H KVSF637A
SOL ASSY,27 SO
SOL ASSY,27 SO
SW1
SW2
SW3
SW4
SW5
87-A90-673-010
87-A90-673-010
87-A90-673-010
87-A90-673-010
87-A90-673-010
SW,MICRO
SW,MICRO
SW,MICRO
SW,MICRO
SW,MICRO
FAN C.B
C180
C181
C182
CN181
CN184
VM2 C.B
CNA004
JACK C.B
0.1-50
0.1-50
0.1-50
0.1-50
0.1-50
F
F
F
F
F
DET C.B
0.22-1W
0.22-1W
0.22-1W
0.22-1W
0.22-1W
J
J
J
J
J
DECK C.B
– 10 –
ESE11SH1C
ESE11SH1C
ESE11SH1C
ESE11SH1C
ESE11SH1C
CHIP RESISTOR PART CODE
Chip Resistor Part Coding
8 8
A
Figure
Resistor Code
Value of resistor
Chip resistor
L
W
t
:A
Resistor Code : A
1.0
0.5
0.35
104
1.6
0.8
0.45
108
2
1.25
0.45
118
3.2
1.6
0.55
128
Dimensions (mm)
Wattage
1/16W
Type
1005
Symbol
CJ
Tolerance
5%
1/16W
1/10W
1608
2125
5%
5%
CJ
CJ
1/8W
3216
5%
CJ
Form
L
t
W
TRANSISTOR ILLUSTRATION
E C B
CDA1585BC
KTA1266GR
KTC3198GR
E C B
B C E
E C B
2SA1980G
2SA1981Y
CC5551
CSB1370EF
CSC4115BC
D
G
B
S
B C E
G D S
2SB1342
2SB1686
2SD1933
2SD2642
2SK2937
2SK2158
– 11 –
C
E
2SA1235F
2SC2714O
2SC3052F
CMBT5401
CMBT5551
CSD1306E
DTC114YKA
KRA102S
KRA107S
KRC102S-RTK
RT1P141C
RT1P441C
WIRING – 1 (MAIN / FAN / VM2)
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
– 12 –
SCHEMATIC DIAGRAM – 1 (MAIN 1 / 4 / FAN)
– 13 –
SCHEMATIC DIAGRAM – 2 (MAIN 2 / 4 : TUNER)
– 14 –
SCHEMATIC DIAGRAM – 3 (MAIN 3 / 4 : AMP)
– 15 –
SCHEMATIC DIAGRAM – 4 (MAIN 4 / 4 : DECK)
– 16 –
WIRING – 2 (FRONT)
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
– 17 –
SCHEMATIC DIAGRAM – 5 (FRONT / DECK)
– 18 –
WIRING – 3 (AC3) <1 / 2>
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
– 19 –
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
WIRING – 3 (AC3) <2 / 2>
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
– 20 –
SCHEMATIC DIAGRAM – 6 (AC3 / VM2)
– 21 –
WIRING – 4 (AMP / JACK / DET)
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
– 22 –
SCHEMATIC DIAGRAM – 7 (AMP / JACK / DET)
– 23 –
WIRING – 5 (PT)
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
– 24 –
SCHEMATIC DIAGRAM – 8 (PT)
– 25 –
WIRING – 6 (DECK)
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
A
TO FRONT C.B CN104
J DECK C.B
SW5
(FFC104)
11 9
SW4
10 8
7
5
6
3
4
1
B
SW3
SW1
SW2
L
(REA)
(CST2)
C
2
CN1
(CAM2)
1
H
+
(CAM1)
(CST1)
D
E
1
IC2
3
SFR1
SOL2
1
R1
SOL1
IC1
F
3
G
H
W1
+
H
L
M1
TAPE
MOTOR
I
J
K
L
M
N
O
P
Q
R
S
T
U
– 26 –
IC BLOCK DIAGRAM
– 27 –
– 28 –
FL (HNA-08MM29) GRID ASSIGNMENT AND ANODE CONNECTION
GRID ASSIGNMENT
– 29 –
ANODE CONNECTION
(UP)
(DOWN)
– 30 –
IC DESCRIPTION
IC, µPD784975AGF-102-3BA
Pin No.
Pin Name
I/O
Description
1
AVDD
–
Power supply.
2
I-HOLD
I
Power failure detected input.
3
I-CDSW
I
CD mecha switch A/D converter input.
4
I-SPEANA_1
I
A/D input for spectrum analyser level display.
5
I-SPEANA_2
I
A/D input for spectrum analyser level display.
6
I-SPEANA_3
I
A/D input for spectrum analyser level display.
7
I-KEY1
I
Key A/D input 1.
8
I-KEY2
I
Key A/D input 2.
9
I-TU_SIG
I
Tuner signal input. (Not used)
10
I-5VMISO
I
IC, CS8415A data input.
11
I-2VMISO
I
IC, CS49326 data input.
12
I-SUBQ
I
CD SUBQ data input.
13
I-DISH
I
CD turntable photo sensor input A/D converter input.
14
AVSS
–
GND.
15
VSS1
–
GND.
16
X1
–
15.6MHz oscillator circuit.
17
X2
–
15.6MHz oscillator circuit.
18
VDD1
–
Power supply.
19
IC
–
Internal connection (connected to GND).
20
I-RMC
I
System remote control signal input.
21
O-POWER
O
System power supply ON/OFF output.
22
I-WRQ
I
CD interrupt signal input.
23
I-DRF
I
CD focus ON detect data input.
24
CODECCSN
O
IC, CS4228A chip select output.
25
O-5VDSPCSN
O
IC, CS49326 chip select output.
26
O-5VMOSI
O
IC, CS8415A, IC, CS4228A, IC, CS49326 data output.
27
I-RDS_CLK
I
Tuner RDS clock input. (Not used)
28
O-5VSCK
O
IC, CS8415A, IC, CS4228A, IC, CS49326 serial clock output.
29
NC
-
Not connected.
30
O-STB
O
MAIN PWB strobe output.
31
DIRCSN
O
IC, CS8415A chip select output.
32
O-5VMRESET
O
IC, CS8415A, IC, CS4228A reset output.
33
O-SOL1
O
DECK1 solenoid ON/OFF output.
34
O-SOL2
O
DECK2 solenoid ON/OFF output.
35
I-HPMUTE
I
Headphone MUTE input.
36
I-8415EMPH
I
Not used.
37
O-KSCAN
O
Switch SCAN timing output.
38
I-8415INT
I
IC, CS8415A INT input.
39
O-MUTE
O
System MUTE ON/OFF output.
40
VSS0
–
GND.
41
VDD0
–
Power supply.
42
RESET
–
System reset input (ON/OFF).
43
I-RDS_DATA
I
Tuner RDS data input. (Not used)
– 31 –
Pin No.
Pin Name
I/O
Description
44
O-DSC/O-DATA
O
Function IC / Tuner IC, data output.
45
I-STEREO
I
Tuner STEREO detect input.
46
I-IFC
I
Tune IF count serial data input.
47
O-5VDSPRESET
O
IC, CS49326 reset output.
48
I-2VINTREQ
I
IC, CS49326 INT input.
49
NC
–
Not connected.
50
O-STB(SHIFT)
O
Shift register strobe output.
51
O-PLL_CLK
O
PLL IC clock enable output.
52
O-PLL_CE
O
PLL IC chip enable output.
53, 54
P1, P2
O
FL segment P1, P2 output.
55
O-CD_CLK
O
CD clock output.
56
O-CD_DATA
O
CD data output.
57
O-CD_CE
O
CD chip enable output.
58
P3
O
FL segment P3 output.
59
I-JOG_B
I
Dial jog rotary encoder input B.
60
I-JOG_A
I
Dial jog rotary encoder input A.
61
I-VOL_B
I
Volume rotary encoder input B.
62
I-VOL_A
I
Volume rotary encoder input A.
63
P4/AM10K
O/I
64
I-TM_BASE
I
65
P5/I-AMST
O/I
FL segment P5 output / AM stereo diode input (Not used).
66
P6/I-LW
O/I
FL segment P6 output / LW diode input (Not used).
67
P7/I-AUTO2
O/I
FL segment P7 output / DECK2 AUTO STOP switch data input.
68
P8/I-AUTO1
O/I
FL segment P8 output / DECK1 AUTO STOP switch data input.
69
P9/I-CST2
O/I
FL segment P9 output / DECK2 cassette detect switch data input.
70
P10/I-CST1
O/I
FL segment P10 output / DECK1 cassette detect switch data input.
71
P11/CAM2
O/I
FL segment P11 output / DECK2 CAM switch data input.
72
P12/I-CAM1
O/I
FL segment P12 output / DECK1 CAM switch data input.
73
P13/I-REB
O/I
FL segment P13 output / DECK2 side B record OK switch data input (Not used).
74
P14/I-REA
O/I
FL segment P14 output / DECK2 side A record OK switch data input.
75
P15/OIRT
O/I
FL segment P15 output / OIRT diode input (Not used).
76
P16/RDS
O/I
FL segment P16 output / RDS input to diode (Not used).
77
P17/R+1
O/I
FL segment P17 output / DECK R+1 diode input (Not used).
78
P18/DEMO
O/I
FL segment P18 output / DEMO diode input (Not used).
79
VDD2
–
Power supply.
80
VLOAD
–
Power supply for FL display.
81
P19/C-JACK
O/I
FL segment P19 output / C-JACK data input (Not used).
82
P20/ECO-OFF
O/I
FL segment P20 output / ECO-OFF data input (Not used).
83
P21/DTS
O/I
FL segment P21 output / DTS diode input (Not used).
84
P22/SW
O/I
FL segment P22 output / SW diode input (Not used).
85 ~ 92
P23 ~ P30
O
FL segment P23 ~ P30 output.
93 ~ 100
G1 ~ G8
O
FL grid G1 ~ G8 output.
FL segment P4 output / AM10K diode input (Not used).
Base input for clock.
– 32 –
ADJUSTMENT <TUNER / FRONT / DECK>
< TUNER SECTION >
< DECK SECTION >
1. Clock Frequency Check
Settings : • Test point : TP2(CLK)
Method : Set to AM 1710kHz and check that the test point is
2160kHz ± 45Hz.
9. Tape Speed Adjustment (DECK 2)
Settings : • Test tape : TTA–100
• Test point : TP8(Lch), TP9(Rch)
• Adjustment location : SFR1
Method : Play back the test tape and adjust SFR1 so that the
frequency counter reads 3000Hz ± 5Hz.
2. AM VT Check
Settings : • Test point : TP1(VT)
Method : Set to AM 1710kHz and check that the test point is less
than 8.5V.
Then set to AM 530kHz and check that the test point is
more than 0.6V.
3. FM VT Check
Settings : • Test point : TP1(VT)
Method : Set to FM 87.5MHz and check that the test point is more
than 0.5V.
Then set to FM 108.0MHz and check that the test point
is less than 8.0V.
4. AM Tracking Adjustment
Settings : • Test point : TP8(Lch), TP9(Rch)
• Adjustment location : L951(1/3)
Method : Set to AM 1000kHz and adjust L951(1/3) to maximum.
13. REC/PB Frequency Response Adjustment (DECK 2)
Settings : • Test tape : TTA–602
• Test point : TP8(Lch), TP9(Rch)
• Input signal : 1kHz / 8kHz (LINE IN)
• Adjustment location : SFR351 (Lch)
SFR352 (Rch)
Method : Apply a 1kHz signal and REC mode. Then adjust OSC
attenuator so that the output level at the TP8, TP9
becomes -20VU (21mV). Record and play back the
1kHz and 8kHz signals and adjust SFRs so that the
output of the 8kHz signals becomes 0dB ± 0.5dB with
respect to that of the 1kHz signal.
6. AM IF Adjustment
Settings : • Test point : TP8(Lch), TP9(Rch)
• Adjustment location :
L802 ............................................................ 450kHz.
7. DC Balance / Mono Distortion Adjustment
Settings : • Test point : TP3, TP4 (DC Balance)
TP8(Lch), TP9(Rch) (Distortion)
• Adjustment location : L801
• Input level : 60dBµV
Method : Set to FM 98.0MHz and adjust L801 so that the
distortion becomes minimum. Next, check that the
voltage between TP3 and TP4 is 0V ± 500mV.
< FRONT SECTION >
µ-CON
11. PB Frequency Response Check (DECK 1, DECK 2)
Settings : • Test tape : TTA–330
• Test point : TP8(Lch), TP9(Rch)
Method : Play back the 315Hz and 8kHz signals of the test tape
and check that the output ratio of the 8kHz signal with
respect to that of the 315Hz signal is within 3dB.
12. PB Sensitivity Check (DECK 1, DECK 2)
Settings : • Test tape : TTA–200
• Test point : TP8(Lch), TP9(Rch)
Method : Play back the test tape and check that the output level of
the test point is 280mV ± 3dB.
5. FM Tracking Check
Settings : • Test point : TP8(Lch), TP9(Rch)
Method : Set to FM 98.0MHz and check that the test point is less
than 13dBµV.
8.
10. Head Azimuth Adjustment (DECK 1, DECK 2)
Settings : • Test tape : TTA–330
• Test point : TP8(Lch), TP9(Rch)
• Adjustment location : Azimuth adjustment screw
Method : Play back (FWD) the 8kHz signal of the test tape and
adjust screw so that the output becomes maximum.
Next, perform on REV PLAY mode.
OSC Adjustment
Settings : • Test point : TP11(KEY-SCAN), (GND)
• Adjustment location : L951
Method : Connect a frequency counter across TP11(KEY-SCAN)
and GND. Insert AC plug while pressing TUNER function
key and POWER key. Then adjust L951 so that the test
point becomes 67.708Hz ± 0.068Hz.
To manual reset press POWER key while pressing
CLEAR key.
14. REC/PB Sensitivity Check (DECK 2)
Settings : • Test tape : TTA–602
• Test point : TP8(Lch), TP9(Rch)
• Input signal : 8kHz (LINE IN)
Method : Apply a 8kHz signal and REC mode. Then adjust OSC
attenuator so that the output level at TP8, TP9 becomes
0VU (210mV). Record and play back the 8kHz signal
and check that the output is -1dB ± 3.5dB.
– 33 –
CD TEST MODE
1. How to Start the CD Test Mode
While pressing the FUNCTION button, insert the AC plug to the power outlet.
When the test mode is started, the message [CD TEST] is displayed.
2. How to Exit the CD Test Mode
Press the POWER button or disconnect the AC plug.
* When any key other than PRESET is pressed during play mode, the machine exits the test mode.
3. Function Descriptions and Application of the CD Test Mode
No
Mode
1
Start mode
Operation
Display
Function
All indicators light • All FL indicators light
Checking item
• FL check
• Microprocessor check
2
Search
CLEAR
mode
button
READING
• LD illuminates all the time
• APC circuit check
• Focus search continuous
• Laser current measurement
operations *1
• Focus search waveform check
• Spindle motor continuous kick • Focus error waveform check
(DRF in the search mode is
ignored)
3
Play mode
PRESET
Normal
button
• Normal playback
• Each servo circuit is checked
• If TOC cannot be read, focus
• DRF check
search is continued
4
Traverse
SET
mode
button
Normal
• Tracking servo OFF/ON
• Tracking balance check
• Each time PAUSE button is
pressed, the tracking servo
repeats turning OFF/ON
5
Sled mode UP button
CD TEST
• Pickup moves to the inner
circumference *2
• Sled circuit check
• Tracking circuit check
At the same time, lens kicks to • Mechanism operation check
the inner circumference
DOWN
button
CD TEST
• Pickup check
• Pickup moves to the outer
circumference *2
At the same time, lens kicks to
the outer circumference
6
Spindle
mode
REC/REC All indicators light • The spindle motor rotates
MUTE
forward (rough speed) by
button
pressing the button and
• Spindle circuit
• Spindle motor
rotates backward by pressing
one more time and stops by
pressing again
*1: The driver IC heats up and the protection circuit starts working when the focus search is continued for 10 minutes or longer.
There can be a case that operations cannot be performed correctly.
In such a case, turn off the main power. After cooling down the machine, restart the machine.
*2: Be careful not to damage the gear because the sled motor rotates while the UP or DOWN button is being pressed even if the
pick-up is located in the innermost track or the outermost track.
– 34 –
MECHANICAL EXPLODED VIEW 1 / 1
A
BZG-5 ZD3NM
47
A
L
PWB
A
A
A
24
50
PWB
45
WIRE,
BINDER
M
48
C
32
A
44
A
49
43
F
A
31
J
PWB
22
FL901
30
PWB
M
WIRE,
BINDER
40
N
C
37
G
34
54
15
42
17 18
I
23
19
D
53
H
O 46
A
1
A
A
20
48
A
A
16
WIRE,
BINDER
HT-SINK,
FIN T2
A
PWB
35
2
HT-SINK,S
41
O
O
25
A
PWB
H
51
N
I
A
52
5
46
3
39
A
6
20
N
A
A
13
14
26
38
E
27
28
7
21
B
8
4
10
33
28
27
PLATE,EATH MECH
29
ZZM-3 PR3NM A
K
36
9
CHAS,MAIN
11
12
– 35 –
J
MECHANICAL PARTS LIST 1 / 1
REF. NO. PART NO.
1
2
3
3
4
8B-NFK-008-010
8B-NFK-013-010
8B-NCK-011-010
8B-NCK-013-010
8B-NFK-033-010
KANRI
DESCRIPTION
NO.
PANEL,TRAY
WINDOW,TRAY
WINDOW,DISP U<50>
WINDOW,DISP U DS55<55>
PANEL,FR U
5
6
7
8
9
8B-NCK-006-010
8B-NFK-024-010
8A-NF8-281-010
8B-NFK-003-010
8B-NFK-011-010
10
11
12
13
14
REF. NO. PART NO.
KANRI
DESCRIPTION
NO.
AC CORD ASSY,U BLK
HLDR,PWB PNRM R
HLDR,TR 1
HLDR,PWB PNRM F
HLDR,PWB AMP
39
40
41
42
43
87-A80-149-010
8B-NF7-236-010
8B-NCK-206-010
8B-NF7-235-010
8B-NCK-209-010
KEY,ASSY FUNCTION DD
KEY,CD
SPR-T,EJECT 1
BOX,CASS 1
WINDOW,CASS 1 1WAY
44
45
46
47
48
8B-NCK-202-010
8B-NCK-208-010
87-064-185-010
87-084-079-010
87-A90-457-010
HLDR,PWB DD
HLDR,TR AMP
HLDR,WIRE
RIVET,NYL 4-5
F-BEAD,15-25-15 E251
8A-NF8-282-010
8B-NFK-004-010
8B-NFK-012-010
8B-NFK-014-010
8B-NFK-015-010
SPR-T,EJECT 2
BOX,CASS 2
WINDOW,CASS 2
KNOB,RTRY VOL
KNOB,RTRY JOG
49
50
51
52
53
87-A90-173-010
8B-NCK-210-010
8B-NF7-238-010
87-A92-117-010
88-912-371-110
F-BEAD,9-20-21 ZCAT
HLDR,TR AMP ST
HLDR,FAN LOW
FAN,ASB0812H(DELTA)-400MM
FF-CABLE,12P 1.25 37
15
16
17
18
19
8B-NFK-016-010
8B-NFK-029-010
8B-NCK-021-010
8B-NFK-018-010
8B-NFK-026-010
KEY,POWER
LENS,SENSOR
KEY,DOLBY
KEY,PLAY 1WAY
KEY,ENTER
54
A
B
C
D
88-907-121-110
87-067-703-010
87-067-688-010
87-NF4-224-010
87-723-096-410
FF-CABLE,7P 120
TAPPING SCREW, BVT2+3-10
BVTT+3-6
S-SCREW,IT3B+3-8 CU
QT2+3-10W/O SLOT BL
20
21
22
23
24
8Z-NF6-210-010
8B-NCK-001-010
8B-NFK-201-010
88-908-301-110
88-906-251-110
DMPR,150 N
CABI,FR U
GUIDE,FL
FF-CABLE,8P 1.25
FF-CABLE,6P 1.25(RVS-FACE)
E
F
G
H
I
87-721-096-410
8A-NF7-251-010
87-067-689-010
87-078-200-010
87-721-097-410
QT2+3-10 GLD
W,3.2-8-0.45
TAPPING SCREW, BVTT+3-8
S-SCREW,ITC+4-8 R
QT2+3-12 GLD
25
26
27
28
29
88-911-101-110
87-NF4-216-010
86-NF9-224-010
82-NF5-229-010
87-NF4-217-110
FF-CABLE,11P 1.25
HLDR,LOCK 1
SPR-C,LOCK
PLATE,LOCK
HLDR,LOCK 2
J
K
L
M
N
87-067-641-010
87-067-698-010
87-067-758-010
87-067-585-010
87-067-579-010
UTT2+3-8(W/O SLOT)BL
BVT2+3-18(W/O,SLOT)
BVT2+3-12 W/O SLOT
BVTT+4-6
BVT2+3-8 W/O SLOT
30
31
32
33
34
8B-NFK-006-010
8B-NFK-040-010
8A-NF8-206-010
8A-NHZ-021-010
8A-DB8-209-010
PANEL,LEFT
PANEL,TOP
HLDR,PWB M
FOOT,H20
HLDR,PWB PT
O
87-B10-315-010
BVIT3B+3-8 R W/O
35
36
37
37
38
8B-NFK-027-010
8B-NCK-008-010
8B-NCK-031-010
8B-NCK-032-010
87-A91-422-010
REFLECTOR,ECO
PANEL,RIGHT BNC-19
PANEL,REAR USM<50>
PANEL,REAR USM DS55<55>
BUSHING,AC CORD(U)
!
COLOR NAME TABLE
Basic color symbol
Color
Basic color symbol
Color
Basic color symbol
Color
B
Black
C
Cream
D
Orange
G
Green
H
Gray
L
Blue
LT
Transparent Blue
N
Gold
P
Pink
R
Red
S
Silver
ST
Titan Silver
T
Brown
V
Violet
W
White
WT
Transparent White
Y
Yellow
YT
Transparent Yellow
LM
Metallic Blue
LL
Light Blue
GT
Transparent Green
LD
Dark Blue
DT
Transparent Orange
GM
Metallic Green
YM
Metallic Yellow
DM
Metallic Orange
PT
Transparent Pink
LA
Aqua Blue
GL
Light Green
HT
Transparent Gray
– 36 –
TAPE MECHANISM EXPLODED VIEW 1 / 1
TERMINAL,
LB1
33
A
34
55
A
44
45
43
36
42
31
32
41
46
51
TERMINAL,LB1
33
45
51
35
A
52
44
52
31
32
b
a
29
43
47
29
40
39
28
48
50
42
53
46
49
35
41
30
27
37
47
B
38
21
a
48
40
19
27
49
20
26
25
b
24
17
23
18
16
22
28
30
21
26
20
25
24
19
IC, EW732
23
18
22
IC, EW732
54
9
5
6
38
1
14
54
39
2
10
11
c
c
5
6
3
37
9
14
15
16
PWB
10
7
11
12
8
4
12
15
13
– 37 –
13
TAPE MECHANISM PARTS LIST 1 / 1
31
32
33
34
35
8Z-ZM3-233-010
84-ZM2-227-310
87-A92-198-010
87-A90-404-010
8Z-ZM3-239-010
KANRI
DESCRIPTION
NO.
SPR-T,BRG M3
SPR-C,AZIMUTH
HEAD,PH HASVH 2504A
HEAD,EH LE15B
SPR-E,FR
GEAR,CAM TD20
FLY-WHL ASSY,M3 R
FLY-WHL ASSY,M3 L
SPR-T,TRIG
CLR,MG
36
37
38
39
40
8Z-ZM3-211-010
8Z-ZM3-225-010
8Z-ZM3-221-010
8Z-ZM3-234-010
8Z-ZM3-223-010
LEVER,EJECT R
LEVER,STOP
LEVER,CAS
SPR-T,LVR CAS
SPR-C,REEL R M3
82-ZM3-616-010
8Z-ZM3-243-010
8Z-ZM3-238-010
8Z-ZM3-219-010
8Z-ZM3-206-010
RING MAGNET 4
LEVER ASSY,HD UP
SPR-T,HD UP
GEAR,CAM M3
LEVER,TRIG
41
42
43
44
45
8Z-ZM1-225-110
8Z-ZM3-240-010
8Z-ZM3-237-010
8Z-ZM3-215-010
8Z-ZM1-261-110
GEAR,REEL R
SPR-T,T-UP M3
SPR-T,PINCH M3
LEVER,PINCH M3
ROLLER ASSY,PINCH
16
17
18
19
20
8Z-ZM3-209-010
8Z-ZM3-203-010
8Z-ZM1-228-010
8Z-ZM1-265-010
8Z-ZM1-227-010
LEVER,CAM FR
CHAS ASSY,M3
GEAR,SLIP T-UP B
FELT,T-UP
GEAR,SLIP T-UP A
46
47
48
49
50
8Z-ZM1-226-010
8Z-ZM3-222-010
8Z-ZM3-251-010
8Z-ZM3-236-010
82-ZM1-240-110
GEAR,REEL L
SPR-C,REEL L M3
GEAR,IDL REW M3
SPR-T,PLAY M3
LVR,REC(*)
21
22
23
24
25
8Z-ZM1-251-110
8Z-ZM1-275-010
8Z-ZM1-257-010
8Z-ZM1-236-010
8Z-ZM3-226-010
SPR-C,T-UP SLIP
W-L,1,47-4-0.25
SPR-C,F/R
CLR,SLIP FF/REW
SPR-C,FR M3
51
52
53
54
55
8Z-ZM3-216-010
87-B10-301-010
8Z-ZM3-212-010
8Z-ZM3-214-010
86-ZM3-605-110
LEVER,T-UP M3
W-L,1.63-3.2-05 SLIT
LEVER,EJECT L
HLDR,IC
CONN ASSY,8P -RPB
26
27
28
29
30
8Z-ZM3-250-010
8Z-ZM1-269-010
8Z-ZM1-238-110
8Z-ZM3-220-010
8Z-ZM3-205-010
GEAR,SLIP F/R A M3
FELT,FF/REW 2
GEAR,SLIP FF/REW B 2
LEVER,FR M3
LEVER,PLAY M3
A
B
84-ZM2-242-010
8Z-ZM2-220-110
S-SCREW,AZ1-2-6.4
V+2.6 ZZM-2
REF. NO. PART NO.
1
2
3
4
5
8Z-ZM3-227-010
8Z-ZM3-235-010
8Z-ZM1-235-010
87-045-347-010
8Z-ZM1-232-010
6
7
8
9
10
8Z-ZM3-244-010
8Z-ZM3-256-010
8Z-ZM3-255-010
8Z-ZM3-231-010
8Z-ZM3-213-010
11
12
13
14
15
REF. NO. PART NO.
KANRI
DESCRIPTION
NO.
BELT,MAIN M3
BELT,MAIN L
PULLEY,MOT
MOT,SHU2L 70
GEAR,IDL FF/REW
– 38 –
GENERAL SPEAKER DISASSEMBLY INSTRUCTIONS (FOR REFERENCE)
Type.1
Type.4
TOOLS
Insert a flat-bladed screwdriver into the position indicated by the
arrows and remove the panel. Remove the screws of each speaker
unit and then remove the speaker units.
1 Plastic head hammer
2 (() flat head screwdriver
3 Cut chisel
1
2
3
How to Remove the PANEL, FR
Type.2
Remove the grill frame and four pieces of rubber caps by pulling
out with a flat-bladed screwdriver. Remove the screws from hole
where installed rubber caps. Insert a flat-bladed screwdriver into
the position indicated by the arrows and remove the panel. Remove the screws of each speaker unit and then remove the speaker
units.
1.
Insert the (() flat head screwdriver tip into the gap
between the PANEL, FR and the PANEL, SPKR. Tap the
head of the (() flat head screwdriver with the plastic
hammer head, and create the clearance as shown in Fig-1.
2.
Insert the cut chisel in the clearance, and tap the head of
the cut chisel with plastic hammer as shown in Fig-2, to
remove the PANEL, FR.
3.
Place the speaker horizontally. Tap head of the cut chisel
with plastic hammer as shown in Fig-3, and remove the
PANEL, FR completely.
Type.3
Insert a flat-bladed screwdriver into the position indicated by the
arrows and remove the panel. Turn the speaker unit to counterclockwise direction while inserting a flat-bladed screwdriver into
one of the hollows around speaker unit, and then remove the speaker
unit. After replacing the speaker unit, install it turning to clockwise
direction until "click" sound comes out.
Fig-1
Fig-2
Fig-3
How to Attach the PANEL, FR
Attach the PANEL, FR to the PANEL, SPKR. Tap the four
corners of the PANEL, FR with the plastic hammer to fit the
PANEL, FR into the PANEL, SPKR completely.
– 39 –
SPEAKER PARTS LIST
SX-NAJ502 (YUSC,YUSC9,YUSL)
REF. NO. PART NO.
1
2
3
4
4
KANRI
DESCRIPTION
NO.
8B-NS0-001-010
PANEL,FR
8B-NS0-003-010
GRILLE,FRAME ASSY
8B-NS0-008-010
PROTECTOR,TW
8B-NSK-602-010
SPKR,W 160<YUSC>
8B-NS0-602-010
SPKR,W 160 30/4<YUSC9,YUSL>
5
6
7
87-NSH-612-010
87-NS7-611-010
8B-NSK-604-010
SPKR,CERAMIC ASSY
CORD,SPKR
SPKR,T 60
SPEAKER PARTS LIST
SX-R290 (YUSC)
REF. NO. PART NO.
1
2
3
4
5
KANRI
DESCRIPTION
NO.
8B-YS1-003-010
PANEL,FR
8B-YS1-002-010
PROTECTOR,ASSY
81-VSA-009-010
CORD,BUSH
87-YS6-002-010
SPKR,CORD Y
8B-YS1-602-010
SPKR,100 L
6
87-010-384-010
CAP,E 100-25 M SME
SPEAKER PARTS LIST
SX-C610 (YUSC)
REF. NO. PART NO.
1
2
3
4
5
KANRI
DESCRIPTION
NO.
8B-YS2-002-010
PANEL,REAR
8B-YS2-003-010
PROTECTOR,ASSY
81-VSA-009-010
CORD,BUSH
83-NSM-010-010
SPKR,CORD
8B-YS2-604-010
SPKR,100 L
ACCESSORIES / PACKAGE LIST
REF. NO. PART NO.
1
2
3
4
KANRI
DESCRIPTION
NO.
8B-NCK-903-010
IB,U(ESF)M
87-043-115-010
ANT,FEEDER FM
87-006-268-010
ANT LOOP,AM
8B-NCK-702-010
RC UNIT,RC-BAS10 VS
– 40 –
2–11, IKENOHATA 1–CHOME, TAITO-KU, TOKYO 110, JAPAN TEL:03 (3827) 3111
9820543 9301978 921338
Printed in Singapore